[bsp][stm32/templates]简化stm32模板下的Kconfig，增加Kconfig参考模板

8 files changed, 201 insertions, 230 deletions

diff --git a/bsp/stm32/libraries/templates/stm32f0xx/board/Kconfig b/bsp/stm32/libraries/templates/stm32f0xx/board/Kconfig
index ae56cab5a4..ad25140f65 100644
--- a/bsp/stm32/libraries/templates/stm32f0xx/board/Kconfig
+++ b/bsp/stm32/libraries/templates/stm32f0xx/board/Kconfig
@@ -30,44 +30,7 @@ menu "On-chip Peripheral Drivers"
                 depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                 default n
         endif
-
-    menuconfig BSP_USING_SPI
-        bool "Enable SPI BUS"
-        default n
-        select RT_USING_SPI
-        if BSP_USING_SPI
-            config BSP_USING_SPI1
-                bool "Enable SPI1 BUS"
-                default n
-
-            config BSP_SPI1_TX_USING_DMA
-                bool "Enable SPI1 TX DMA"
-                depends on BSP_USING_SPI1
-                default n
-                
-            config BSP_SPI1_RX_USING_DMA
-                bool "Enable SPI1 RX DMA"
-                depends on BSP_USING_SPI1
-                select BSP_SPI1_TX_USING_DMA
-                default n
-        endif
-
-    menuconfig BSP_USING_I2C1
-        bool "Enable I2C1 BUS (software simulation)"
-        default n
-        select RT_USING_I2C
-        select RT_USING_I2C_BITOPS
-        select RT_USING_PIN
-        if BSP_USING_I2C1
-            config BSP_I2C1_SCL_PIN
-                int "i2c1 scl pin number"
-                range 1 216
-                default 15
-            config BSP_I2C1_SDA_PIN
-                int "I2C1 sda pin number"
-                range 1 216
-                default 16
-        endif
+        
     source "../libraries/HAL_Drivers/Kconfig"
     
 endmenu
diff --git a/bsp/stm32/libraries/templates/stm32f10x/board/Kconfig b/bsp/stm32/libraries/templates/stm32f10x/board/Kconfig
index 913c52dbbb..fb1f508f27 100644
--- a/bsp/stm32/libraries/templates/stm32f10x/board/Kconfig
+++ b/bsp/stm32/libraries/templates/stm32f10x/board/Kconfig
@@ -31,45 +31,8 @@ menu "On-chip Peripheral Drivers"
                 default n
         endif
 
-    menuconfig BSP_USING_SPI
-        bool "Enable SPI BUS"
-        default n
-        select RT_USING_SPI
-        if BSP_USING_SPI
-            config BSP_USING_SPI1
-                bool "Enable SPI1 BUS"
-                default n
-
-            config BSP_SPI1_TX_USING_DMA
-                bool "Enable SPI1 TX DMA"
-                depends on BSP_USING_SPI1
-                default n
-                
-            config BSP_SPI1_RX_USING_DMA
-                bool "Enable SPI1 RX DMA"
-                depends on BSP_USING_SPI1
-                select BSP_SPI1_TX_USING_DMA
-                default n
-        endif
-
-    menuconfig BSP_USING_I2C1
-        bool "Enable I2C1 BUS (software simulation)"
-        default n
-        select RT_USING_I2C
-        select RT_USING_I2C_BITOPS
-        select RT_USING_PIN
-        if BSP_USING_I2C1
-            config BSP_I2C1_SCL_PIN
-                int "i2c1 scl pin number"
-                range 1 216
-                default 15
-            config BSP_I2C1_SDA_PIN
-                int "I2C1 sda pin number"
-                range 1 216
-                default 16
-        endif
     source "../libraries/HAL_Drivers/Kconfig"
-    
+       
 endmenu
 
 menu "Board extended module Drivers"
diff --git a/bsp/stm32/libraries/templates/stm32f2xx/board/Kconfig b/bsp/stm32/libraries/templates/stm32f2xx/board/Kconfig
index 512a3b5be3..babf0f6e1a 100644
--- a/bsp/stm32/libraries/templates/stm32f2xx/board/Kconfig
+++ b/bsp/stm32/libraries/templates/stm32f2xx/board/Kconfig
@@ -30,46 +30,9 @@ menu "On-chip Peripheral Drivers"
                 depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                 default n
         endif
-
-    menuconfig BSP_USING_SPI
-        bool "Enable SPI BUS"
-        default n
-        select RT_USING_SPI
-        if BSP_USING_SPI
-            config BSP_USING_SPI1
-                bool "Enable SPI1 BUS"
-                default n
-
-            config BSP_SPI1_TX_USING_DMA
-                bool "Enable SPI1 TX DMA"
-                depends on BSP_USING_SPI1
-                default n
-                
-            config BSP_SPI1_RX_USING_DMA
-                bool "Enable SPI1 RX DMA"
-                depends on BSP_USING_SPI1
-                select BSP_SPI1_TX_USING_DMA
-                default n
-        endif
-
-    menuconfig BSP_USING_I2C1
-        bool "Enable I2C1 BUS (software simulation)"
-        default n
-        select RT_USING_I2C
-        select RT_USING_I2C_BITOPS
-        select RT_USING_PIN
-        if BSP_USING_I2C1
-            config BSP_I2C1_SCL_PIN
-                int "i2c1 scl pin number"
-                range 1 216
-                default 15
-            config BSP_I2C1_SDA_PIN
-                int "I2C1 sda pin number"
-                range 1 216
-                default 16
-        endif
+        
     source "../libraries/HAL_Drivers/Kconfig"
-    
+   
 endmenu
 
 menu "Board extended module Drivers"
diff --git a/bsp/stm32/libraries/templates/stm32f4xx/board/Kconfig b/bsp/stm32/libraries/templates/stm32f4xx/board/Kconfig
index 0e5bacf28b..00b23fbd44 100644
--- a/bsp/stm32/libraries/templates/stm32f4xx/board/Kconfig
+++ b/bsp/stm32/libraries/templates/stm32f4xx/board/Kconfig
@@ -30,45 +30,8 @@ menu "On-chip Peripheral Drivers"
                 depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                 default n
         endif
-
-    menuconfig BSP_USING_SPI
-        bool "Enable SPI BUS"
-        default n
-        select RT_USING_SPI
-        if BSP_USING_SPI
-            config BSP_USING_SPI1
-                bool "Enable SPI1 BUS"
-                default n
-
-            config BSP_SPI1_TX_USING_DMA
-                bool "Enable SPI1 TX DMA"
-                depends on BSP_USING_SPI1
-                default n
-                
-            config BSP_SPI1_RX_USING_DMA
-                bool "Enable SPI1 RX DMA"
-                depends on BSP_USING_SPI1
-                select BSP_SPI1_TX_USING_DMA
-                default n
-        endif
-
-    menuconfig BSP_USING_I2C1
-        bool "Enable I2C1 BUS (software simulation)"
-        default n
-        select RT_USING_I2C
-        select RT_USING_I2C_BITOPS
-        select RT_USING_PIN
-        if BSP_USING_I2C1
-            config BSP_I2C1_SCL_PIN
-                int "i2c1 scl pin number"
-                range 1 216
-                default 15
-            config BSP_I2C1_SDA_PIN
-                int "I2C1 sda pin number"
-                range 1 216
-                default 16
-        endif
-    source "../libraries/HAL_Drivers/Kconfig"
+        
+    source "../libraries/HAL_Drivers/Kconfig"    
     
 endmenu
 
diff --git a/bsp/stm32/libraries/templates/stm32f7xx/board/Kconfig b/bsp/stm32/libraries/templates/stm32f7xx/board/Kconfig
index 0ab9b6b224..e78efb71a1 100644
--- a/bsp/stm32/libraries/templates/stm32f7xx/board/Kconfig
+++ b/bsp/stm32/libraries/templates/stm32f7xx/board/Kconfig
@@ -31,43 +31,6 @@ menu "On-chip Peripheral Drivers"
                 default n
         endif
 
-    menuconfig BSP_USING_SPI
-        bool "Enable SPI BUS"
-        default n
-        select RT_USING_SPI
-        if BSP_USING_SPI
-            config BSP_USING_SPI1
-                bool "Enable SPI1 BUS"
-                default n
-
-            config BSP_SPI1_TX_USING_DMA
-                bool "Enable SPI1 TX DMA"
-                depends on BSP_USING_SPI1
-                default n
-                
-            config BSP_SPI1_RX_USING_DMA
-                bool "Enable SPI1 RX DMA"
-                depends on BSP_USING_SPI1
-                select BSP_SPI1_TX_USING_DMA
-                default n
-        endif
-
-    menuconfig BSP_USING_I2C1
-        bool "Enable I2C1 BUS (software simulation)"
-        default n
-        select RT_USING_I2C
-        select RT_USING_I2C_BITOPS
-        select RT_USING_PIN
-        if BSP_USING_I2C1
-            config BSP_I2C1_SCL_PIN
-                int "i2c1 scl pin number"
-                range 1 216
-                default 15
-            config BSP_I2C1_SDA_PIN
-                int "I2C1 sda pin number"
-                range 1 216
-                default 16
-        endif
     source "../libraries/HAL_Drivers/Kconfig"
     
 endmenu
diff --git a/bsp/stm32/libraries/templates/stm32h7xx/board/Kconfig b/bsp/stm32/libraries/templates/stm32h7xx/board/Kconfig
index 249d3d6772..4b0897972c 100644
--- a/bsp/stm32/libraries/templates/stm32h7xx/board/Kconfig
+++ b/bsp/stm32/libraries/templates/stm32h7xx/board/Kconfig
@@ -26,6 +26,7 @@ menu "On-chip Peripheral Drivers"
                 default y
 
         endif
+        
     source "../libraries/HAL_Drivers/Kconfig"
     
 endmenu
diff --git a/bsp/stm32/libraries/templates/stm32l4xx/board/Kconfig b/bsp/stm32/libraries/templates/stm32l4xx/board/Kconfig
index ca508a0961..48708ad3bc 100644
--- a/bsp/stm32/libraries/templates/stm32l4xx/board/Kconfig
+++ b/bsp/stm32/libraries/templates/stm32l4xx/board/Kconfig
@@ -29,47 +29,10 @@ menu "On-chip Peripheral Drivers"
                 bool "Enable UART1 RX DMA"
                 depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                 default n
-        endif
+        endif   
 
-    menuconfig BSP_USING_SPI
-        bool "Enable SPI BUS"
-        default n
-        select RT_USING_SPI
-        if BSP_USING_SPI
-            config BSP_USING_SPI1
-                bool "Enable SPI1 BUS"
-                default n
-
-            config BSP_SPI1_TX_USING_DMA
-                bool "Enable SPI1 TX DMA"
-                depends on BSP_USING_SPI1
-                default n
-
-            config BSP_SPI1_RX_USING_DMA
-                bool "Enable SPI1 RX DMA"
-                depends on BSP_USING_SPI1
-                select BSP_SPI1_TX_USING_DMA
-                default n
-        endif
-
-    menuconfig BSP_USING_I2C1
-        bool "Enable I2C1 BUS (software simulation)"
-        default n
-        select RT_USING_I2C
-        select RT_USING_I2C_BITOPS
-        select RT_USING_PIN
-        if BSP_USING_I2C1
-            config BSP_I2C1_SCL_PIN
-                int "i2c1 scl pin number"
-                range 1 176
-                default 15
-            config BSP_I2C1_SDA_PIN
-                int "I2C1 sda pin number"
-                range 1 176
-                default 16
-        endif
     source "../libraries/HAL_Drivers/Kconfig"
-    
+      
 endmenu
 
 menu "Board extended module Drivers"
diff --git a/bsp/stm32/libraries/templates/stm32xx_board_Kconfig b/bsp/stm32/libraries/templates/stm32xx_board_Kconfig
new file mode 100644
index 0000000000..ce836e027b
--- /dev/null
+++ b/bsp/stm32/libraries/templates/stm32xx_board_Kconfig
@@ -0,0 +1,192 @@
+menu "Hardware Drivers Config"
+
+config SOC_STM32L475VE
+    bool
+    select SOC_SERIES_STM32L4
+    default y
+
+menu "Onboard Peripheral Drivers"
+
+    config BSP_USING_STLINK_TO_USART
+        bool "Enable STLINK TO USART (uart1)"
+        select BSP_USING_UART
+        select BSP_USING_UART1
+        default y
+
+    config BSP_USING_QSPI_FLASH
+        bool "Enable QSPI FLASH (W25Q128 qspi1)"
+        select BSP_USING_QSPI
+        select RT_USING_SFUD
+        select RT_SFUD_USING_QSPI
+        default n
+
+    config BSP_USING_SDCARD
+        bool "Enable SDCARD (spi1)"
+        select BSP_USING_SPI
+        select BSP_USING_SPI1
+        select RT_USING_SPI_MSD
+        select RT_USING_DFS
+        select RT_USING_DFS_ELMFAT
+        default n
+
+endmenu
+
+menu "On-chip Peripheral Drivers"
+
+    config BSP_USING_GPIO
+        bool "Enable GPIO"
+        select RT_USING_PIN
+        default y
+
+    menuconfig BSP_USING_UART
+        bool "Enable UART"
+        default y
+        select RT_USING_SERIAL
+        if BSP_USING_UART
+            config BSP_USING_UART1
+                bool "Enable UART1"
+                default y
+
+            config BSP_UART1_RX_USING_DMA
+                bool "Enable UART1 RX DMA"
+                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
+                default n            
+        endif
+
+    config BSP_USING_ON_CHIP_FLASH
+        bool "Enable on-chip FLASH"
+        default n
+
+    menuconfig BSP_USING_SPI
+        bool "Enable SPI BUS"
+        default n
+        select RT_USING_SPI
+        if BSP_USING_SPI
+            config BSP_USING_SPI1
+                bool "Enable SPI1 BUS"
+                default n
+
+            config BSP_SPI1_TX_USING_DMA
+                bool "Enable SPI1 TX DMA"
+                depends on BSP_USING_SPI1
+                default n
+                
+            config BSP_SPI1_RX_USING_DMA
+                bool "Enable SPI1 RX DMA"
+                depends on BSP_USING_SPI1
+                select BSP_SPI1_TX_USING_DMA
+                default n           
+        endif
+
+    config BSP_USING_QSPI
+        bool "Enable QSPI BUS"
+        select RT_USING_QSPI
+        select RT_USING_SPI
+        default n
+
+    config BSP_QSPI_USING_DMA
+        bool "Enable QSPI DMA support"
+        default n
+
+    menuconfig BSP_USING_I2C
+        bool "Enable I2C BUS"
+        default n
+        select RT_USING_I2C
+        select RT_USING_I2C_BITOPS
+        select RT_USING_PIN
+        if BSP_USING_I2C
+            menuconfig BSP_USING_I2C3
+                bool "Enable I2C3 BUS (software simulation)"
+                default y
+                if BSP_USING_I2C3
+                    comment "Notice: PC0 --> 32; PC1 --> 33" 
+                    config BSP_I2C3_SCL_PIN
+                        int "i2c3 scl pin number"
+                        range 1 176
+                        default 32
+                    config BSP_I2C3_SDA_PIN
+                        int "I2C3 sda pin number"
+                        range 1 176
+                        default 33
+                endif            
+        endif
+
+    menuconfig BSP_USING_TIM
+        bool "Enable timer"
+        default n
+        select RT_USING_HWTIMER
+        if BSP_USING_TIM
+            config BSP_USING_TIM15
+                bool "Enable TIM15"
+                default n
+        endif
+
+    menuconfig BSP_USING_PWM
+        bool "Enable pwm"
+        default n
+        select RT_USING_PWM
+        if BSP_USING_PWM
+        menuconfig BSP_USING_PWM1
+            bool "Enable timer1 output pwm"
+            default n
+            if BSP_USING_PWM1
+                config BSP_USING_PWM1_CH1
+                    bool "Enable PWM1 channel1"
+                    default n
+            endif
+        endif
+
+    menuconfig BSP_USING_ADC
+        bool "Enable ADC"
+        default n
+        select RT_USING_ADC
+        if BSP_USING_ADC
+            config BSP_USING_ADC1
+                bool "Enable ADC1"
+                default n
+        endif
+
+    menuconfig BSP_USING_ONCHIP_RTC
+        bool "Enable RTC"
+        select RT_USING_RTC
+        select RT_USING_LIBC
+        default n
+        if BSP_USING_ONCHIP_RTC
+            choice
+                prompt "Select clock source"
+                default BSP_RTC_USING_LSE
+
+                config BSP_RTC_USING_LSE
+                    bool "RTC USING LSE"
+
+                config BSP_RTC_USING_LSI
+                    bool "RTC USING LSI"
+            endchoice
+        endif
+
+    config BSP_USING_WDT
+        bool "Enable Watchdog Timer"
+        select RT_USING_WDT
+        default n
+
+    config BSP_USING_USBD_FS
+        bool "Enable OTGFS as USB device"
+        select RT_USING_USB_DEVICE
+        default n
+   
+    source "../libraries/HAL_Drivers/Kconfig"
+    
+endmenu
+
+menu "Board extended module Drivers"
+
+    config BSP_USING_NRF24L01
+        bool "Enable NRF24L01"
+        select BSP_USING_SPI
+        select BSP_USING_SPI2
+        select PKG_USING_NRF24L01
+        default n
+
+endmenu
+
+endmenu