diff options
Diffstat (limited to 'bsp/tm4c123bsp/board/Kconfig')
| -rw-r--r-- | bsp/tm4c123bsp/board/Kconfig | 349 |
1 files changed, 349 insertions, 0 deletions
diff --git a/bsp/tm4c123bsp/board/Kconfig b/bsp/tm4c123bsp/board/Kconfig new file mode 100644 index 0000000000..db5b976281 --- /dev/null +++ b/bsp/tm4c123bsp/board/Kconfig @@ -0,0 +1,349 @@ +menu "Hardware Drivers Config" + +config tm4c123 + bool + select RT_USING_COMPONENTS_INIT + select RT_USING_USER_MAIN + default y + + +menu "Onboard Peripheral Drivers" + + config BSP_USING_USB_TO_USART + bool "Enable USB TO USART (uart1)" + select BSP_USING_UART + select BSP_USING_UART1 + default y + + config BSP_USING_RS485_OR_RS232 + bool "Enable RS485/RS232 (uart2 be shared)" + select BSP_USING_UART2 + default n + + config BSP_USING_SPI_FLASH + bool "Enable SPI FLASH (W25Q64 spi1)" + select BSP_USING_SPI + select BSP_USING_SPI1 + select RT_USING_SFUD + select RT_SFUD_USING_SFDP + default n + + config BSP_USING_RGB + bool "Enable RGB LED (timer3 channel2 - 4)" + select RT_USING_PWM + select BSP_USING_PWM + select BSP_USING_PWM3 + select BSP_USING_PWM3_CH2 + select BSP_USING_PWM3_CH3 + select BSP_USING_PWM3_CH4 + default n + + config BSP_USING_POT + bool "Enable potentiometer" + select BSP_USING_ADC + select BSP_USING_ADC1 + default n + + config BSP_USING_EEPROM + bool "Enable I2C EEPROM (i2c1)" + select BSP_USING_I2C1 + default n + + config BSP_USING_ETH + bool "Enable Ethernet Driver (spi2)" + default n + select PKG_USING_WIZNET + select WIZNET_DEVICE_EXTERN_CONFIG + select BSP_USING_SPI2 + if BSP_USING_ETH + if WIZNET_DEVICE_EXTERN_CONFIG + config WIZ_SPI_DEVICE + string + default "spi20" + + config WIZ_RST_PIN + int + default 111 + + config WIZ_IRQ_PIN + int + default 104 + endif + + config EXTERNAL_PHY_ADDRESS + hex + default 0x00 + + endif + + config BSP_USING_SDCARD + bool "Enable SDCARD (sdio)" + select BSP_USING_SDIO + select RT_USING_DFS + select RT_USING_DFS_ELMFAT + default n + +endmenu + +menu "On-chip Peripheral Drivers" + + config BSP_USING_GPIO + bool "Enable GPIO" + select RT_USING_PIN + default y + + menuconfig BSP_USING_UART + bool "Enable UART" + default y + select RT_USING_SERIAL + if BSP_USING_UART + config BSP_USING_UART0 + bool "Enable UART0" + default y + + config BSP_USING_UART1 + bool "Enable UART1" + default n + + config BSP_UART1_RX_USING_DMA + bool "Enable UART1 RX DMA" + depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA + default n + + config BSP_USING_UART2 + bool "Enable UART2" + default n + + config BSP_UART2_RX_USING_DMA + bool "Enable UART2 RX DMA" + depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA + default n + + config BSP_USING_UART3 + bool "Enable UART3" + default n + + config BSP_UART3_RX_USING_DMA + bool "Enable UART3 RX DMA" + depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA + default n + endif + + config BSP_USING_ON_CHIP_FLASH + bool "Enable on-chip FLASH" + default n + + menuconfig BSP_USING_SPI + bool "Enable SPI BUS" + default n + select RT_USING_SPI + if BSP_USING_SPI + config BSP_USING_SPI0 + bool "Enable SPI0 BUS" + default n + + config BSP_USING_SPI1 + bool "Enable SPI1 BUS" + default n + + config BSP_SPI1_TX_USING_DMA + bool "Enable SPI1 TX DMA" + depends on BSP_USING_SPI1 + default n + + config BSP_SPI1_RX_USING_DMA + bool "Enable SPI1 RX DMA" + depends on BSP_USING_SPI1 + select BSP_SPI1_TX_USING_DMA + default n + + config BSP_USING_SPI2 + bool "Enable SPI2 BUS" + default n + + config BSP_SPI2_TX_USING_DMA + bool "Enable SPI2 TX DMA" + depends on BSP_USING_SPI2 + default n + + config BSP_SPI2_RX_USING_DMA + bool "Enable SPI2 RX DMA" + depends on BSP_USING_SPI2 + select BSP_SPI2_TX_USING_DMA + default n + + config BSP_USING_SPI3 + bool "Enable SPI3 BUS" + default n + + config BSP_SPI3_TX_USING_DMA + bool "Enable SPI3 TX DMA" + depends on BSP_USING_SPI3 + default n + + config BSP_SPI3_RX_USING_DMA + bool "Enable SPI3 RX DMA" + depends on BSP_USING_SPI3 + select BSP_SPI3_TX_USING_DMA + default n + endif + + menuconfig BSP_USING_I2C1 + bool "Enable I2C1 BUS (software simulation)" + default n + select RT_USING_I2C + select RT_USING_I2C_BITOPS + select RT_USING_PIN + if BSP_USING_I2C1 + config BSP_I2C1_SCL_PIN + int "i2c1 scl pin number" + range 0 175 + default 22 + config BSP_I2C1_SDA_PIN + int "I2C1 sda pin number" + range 0 175 + default 23 + endif + + menuconfig BSP_USING_TIM + bool "Enable timer" + default n + select RT_USING_HWTIMER + if BSP_USING_TIM + config BSP_USING_TIM2 + bool "Enable TIM2" + default n + + config BSP_USING_TIM3 + bool "Enable TIM3" + default n + + config BSP_USING_TIM4 + bool "Enable TIM4" + default n + + config BSP_USING_TIM5 + bool "Enable TIM5" + default n + endif + + menuconfig BSP_USING_PWM + bool "Enable pwm" + default n + select RT_USING_PWM + if BSP_USING_PWM + menuconfig BSP_USING_PWM0 + bool "Enable pwm0" + default n + if BSP_USING_PWM0 + config BSP_USING_PWM0_CH1 + bool "Enable PWM0 channel1" + default y + + config BSP_USING_PWM0_CH2 + bool "Enable PWM0 channel2" + default n + endif + config BSP_USING_PWM1 + bool "Enable pwm1" + default n + config BSP_USING_PWM2 + bool "Enable pwm2" + default n + config BSP_USING_PWM3 + bool "Enable pwm3" + default n + config BSP_USING_PWM4 + bool "Enable pwm4" + default n + config BSP_USING_PWM5 + bool "Enable pwm5" + default n + config BSP_USING_PWM6 + bool "Enable pwm6" + default n + config BSP_USING_PWM7 + bool "Enable pwm7" + default n + endif + + menuconfig BSP_USING_ADC + bool "Enable ADC" + default n + select RT_USING_ADC + if BSP_USING_ADC + config BSP_USING_ADC0 + bool "Enable ADC0" + default n + config BSP_USING_ADC1 + bool "Enable ADC1" + default n + endif + + menuconfig BSP_USING_ONCHIP_RTC + bool "Enable RTC" + select RT_USING_RTC + select RT_USING_LIBC + default n + if BSP_USING_ONCHIP_RTC + choice + prompt "Select clock source" + default BSP_RTC_USING_LSE + + config BSP_RTC_USING_LSE + bool "RTC USING LSE" + + config BSP_RTC_USING_LSI + bool "RTC USING LSI" + endchoice + endif + + config BSP_USING_WDT + bool "Enable Watchdog Timer" + select RT_USING_WDT + default n + + config BSP_USING_SDIO + bool "Enable SDIO" + select RT_USING_SDIO + select RT_USING_DFS + default n + + menuconfig BSP_USING_CAN + bool "Enable CAN" + default n + select RT_USING_CAN + if BSP_USING_CAN + config BSP_USING_CAN1 + bool "using CAN1" + default n + endif + + config BSP_USING_USBD + bool "Enable USB device" + select RT_USING_USB_DEVICE + default n + if BSP_USING_USBD + config BSP_USB_CONNECT_PIN + int "USB connect pin" + default 67 + + config BSP_USB_PULL_UP_STATUS + int "USB PULL UP STATUS" + default 0 + endif + config BSP_USING_CRC + bool "Enable CRC (CRC-32 0x04C11DB7 Polynomial)" + select RT_USING_HWCRYPTO + select RT_HWCRYPTO_USING_CRC + # "Crypto device frame dose not support above 8-bits granularity" + # "Reserve progress, running well, about 32-bits granularity, such as stm32f1, stm32f4" + default n + +endmenu + +menu "Board extended module Drivers" + +endmenu + +endmenu |