| Age | Commit message (Collapse) | Author |
|---|
|
This patch improves the efficiency and readability of the AArch64 common setup
code by calculating the `PV_OFFSET` once at the start and reusing the value.
This change reduces redundant calculations.
Signed-off-by: Shell <[email protected]>
|
|
Rewrote the spi driver.
Reuse the driver code from https://github.com/sophgo/cvi_alios_open,
which is Apache 2.0 licenced.
Signed-off-by: flyingcys <[email protected]>
Reviewed-by: Chen Wang <[email protected]>
|
|
[libcpu/rv64] feat: unify tick.c
|
|
|
|
Update dfs_cromfs.c
|
|
```
./bsp/cvitek/drivers/drv_wdt.c: In function '_wdt_control':
warning: assignment to 'void *' from 'unsigned int' makes pointer
from integer without a cast [-Wint-conversion]
119 | wdt_device->parent.user_data = (rt_uint32_t)(*(rt_uint32_t *)arg);
| ^
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
122 | *(rt_uint32_t *)arg = (rt_uint32_t)wdt_device->parent.user_data;
| ^
```
Rootcasue: It's not portable to store integar in a pointer.
Solution: use global _wdt_dev to store the timeout value.
Signed-off-by: Chen Wang <[email protected]>
|
|
Optimize the original i2c driver code.
Signed-off-by: flyingcys <[email protected]>
Reviewed-by: Chen Wang <[email protected]>
|
|
Do unmap before shrink so we don't see mapped entry on page table
insertion, which is not acceptable for riscv implementation of
architecture porting.
Changes:
- add un-mapping of pte on `_null_shrink()`
Signed-off-by: Shell <[email protected]>
|
|
Signed-off-by: Chen Wang <[email protected]>
|
|
Board level pin available info:
duo & duo256:
NAME SPI CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP6 SPI2_SCK PWR_GPIO[23] SD1_CLK__SPI2_SCK
GP7 SPI2_SDO PWR_GPIO[22] SD1_CMD__SPI2_SDO
GP8 SPI2_SDI PWR_GPIO[21] SD1_D0__SPI2_SDI
GP9 SPI2_CS_X PWR_GPIO[18] SD1_D3__SPI2_CS_X
Signed-off-by: Chen Wang <[email protected]>
|
|
Board level pin available info is summarized and list here for memo:
Duo:
NAME PWM CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
PWM-1
GP9 PWM4 PWR_GPIO[18] SD1_D3__PWM_4
GP12 PWM4 XGPIOA[16] UART0_TX__PWM_4
GP4 PWM5 PWR_GPIO[19] SD1_D2__PWM_5
GP13 PWM5 XGPIOA[17] UART0_RX__PWM_5
GP5 PWM6 PWR_GPIO[20] SD1_D1__PWM_6
GP8 PMW7 PWR_GPIO[21] SD1_D0__PWM_7
PWM-2
GP7 PWM8 PWR_GPIO[22] SD1_CMD__PWM_8
GP6 PWM9 PWR_GPIO[23] SD1_CLK__PWM_9
GP2 PWM10 PWR_GPIO[26] SD1_GPIO1__PWM_10
GP3 PWM11 PWR_GPIO[25] SD1_GPIO0__PWM_11
Duo256:
NAME PWM CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
PWM-1
GP9 PWM4 PWR_GPIO[18] SD1_D3__PWM_4
GP12 PWM4 XGPIOA[16] UART0_TX__PWM_4
GP4 PWM5 PWR_GPIO[19] SD1_D2__PWM_5
GP13 PWM5 XGPIOA[17] UART0_RX__PWM_5
GP3 PWM6 XGPIOA[18] JTAG_CPU_TCK__PWM_6
GP5 PWM6 PWR_GPIO[20] SD1_D1__PWM_6
GP2 PWM7 XGPIOA[19] JTAG_CPU_TMS__PWM_7
GP8 PMW7 PWR_GPIO[21] SD1_D0__PWM_7
PWM-2
GP7 PWM8 PWR_GPIO[22] SD1_CMD__PWM_8
GP6 PWM9 PWR_GPIO[23] SD1_CLK__PWM_9
GP10 PWM10 XGPIOC[14] PAD_MIPI_TXM1__PWM_10
GP11 PWM11 XGPIOC[15] PAD_MIPI_TXP1__PWM_11
Signed-off-by: Chen Wang <[email protected]>
|
|
Board level UART pinmux summary, following capability
should be controlled by pinname whitelist.
Duo:
NAME UART CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP13 UART0_RX XGPIOA[17] UART0_RX__UART0_RX
GP12 UART0_TX XGPIOA[16] UART0_TX__UART0_TX
GP1 UART1_RX XGPIOA[29] IIC0_SDA__UART1_RX
GP13 UART1_RX XGPIOA[17] UART0_RX__UART1_RX
GP0 UART1_TX XGPIOA[28] IIC0_SCL__UART1_TX
GP12 UART1_TX XGPIOA[16] UART0_TX__UART1_TX
GP1 UART2_RX XGPIOA[29] IIC0_SDA__UART2_RX
GP5 UART2_RX PWR_GPIO[20] SD1_D1__UART2_RX
GP0 UART2_TX XGPIOA[28] IIC0_SCL__UART2_TX
GP4 UART2_TX PWR_GPIO[19] SD1_D2__UART2_TX
GP5 UART3_RX PWR_GPIO[20] SD1_D1__UART3_RX
GP4 UART3_TX PWR_GPIO[19] SD1_D2__UART3_TX
GP3 UART4_RX PWR_GPIO[25] SD1_GPIO0__UART4_RX
GP2 UART4_TX PWR_GPIO[26] SD1_GPIO1__UART4_TX
Duo 256m:
NAME UART CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP13 UART0_RX XGPIOA[17] UART0_RX__UART0_RX
GP12 UART0_TX XGPIOA[16] UART0_TX__UART0_TX
GP1 UART1_RX XGPIOA[29] IIC0_SDA__UART1_RX
GP3 UART1_RX XGPIOA[18] JTAG_CPU_TCK__UART1_RX
GP13 UART1_RX XGPIOA[17] UART0_RX__UART1_RX
GP0 UART1_TX XGPIOA[28] IIC0_SCL__UART1_TX
GP2 UART1_TX XGPIOA[19] JTAG_CPU_TMS__UART1_TX
GP12 UART1_TX XGPIOA[16] UART0_TX__UART1_TX
GP1 UART2_RX XGPIOA[29] IIC0_SDA__UART2_RX
GP5 UART2_RX PWR_GPIO[20] SD1_D1__UART2_RX
GP0 UART2_TX XGPIOA[28] IIC0_SCL__UART2_TX
GP4 UART2_TX PWR_GPIO[19] SD1_D2__UART2_TX
GP5 UART3_RX PWR_GPIO[20] SD1_D1__UART3_RX
GP4 UART3_TX PWR_GPIO[19] SD1_D2__UART3_TX
Note: this patch also update the .config and rtconfig.h
because this patch modify some configuration items's name,
for example: RT_USIMG_UART0 -> BSP_USING_UART0.
FIXME: only handle RISC-V related, no ARM.
Signed-off-by: Chen Wang <[email protected]>
|
|
Based on new pinmux framework, add configuration for uart.
Board level pin available info is summarized and should be
controlled by pin whitelist.
Duo
NAME I2C CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP0 I2C0_SCL XGPIOA[28] IIC0_SCL__IIC0_SCL
GP1 I2C0_SDA XGPIOA[29] IIC0_SDA__IIC0_SDA
GP4 I2C1_SCL PWR_GPIO[19] SD1_D2__IIC1_SCL
GP9 I2C1_SCL PWR_GPIO[18] SD1_D3__IIC1_SCL
GP11 I2C1_SCL XGPIOC[10] PAD_MIPIRX0N__IIC1_SCL
GP5 I2C1_SDA PWR_GPIO[20] SD1_D1__IIC1_SDA
GP8 I2C1_SDA PWR_GPIO[21] SD1_D0__IIC1_SDA
GP10 I2C1_SDA XGPIOC[9] PAD_MIPIRX1P__IIC1_SDA
GP7 I2C3_SCL PWR_GPIO[22] SD1_CMD__IIC3_SCL
GP6 I2C3_SDA PWR_GPIO[23] SD1_CLK__IIC3_SDA
Duo256m
NAME I2C CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP4 I2C1_SCL PWR_GPIO[19] SD1_D2__IIC1_SCL
GP9 I2C1_SCL PWR_GPIO[18] SD1_D3__IIC1_SCL
GP5 I2C1_SDA PWR_GPIO[20] SD1_D1__IIC1_SDA
GP8 I2C1_SDA PWR_GPIO[21] SD1_D0__IIC1_SDA
GP11 I2C2_SCL XGPIOC[15] PAD_MIPI_TXP1__IIC2_SCL
GP10 I2C2_SDA XGPIOC[14] PAD_MIPI_TXM1__IIC2_SDA
GP7 I2C3_SCL PWR_GPIO[22] SD1_CMD__IIC3_SCL
GP6 I2C3_SDA PWR_GPIO[23] SD1_CLK__IIC3_SDA
Duo S(Note, we have not supported duo S, just list for memo)
NAME I2C CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
J3-B18 I2C1_SCL XGPIOB[18] VIVO_D3__IIC1_SCL
J3-B12 I2C1_SCL XGPIOB[12] VIVO_D9__IIC1_SCL
J3-B11 I2C1_SDA XGPIOB[11] VIVO_D10__IIC1_SDA
J3-B13 I2C2_SCL XGPIOB[13] VIVO_D8__IIC2_SCL
J4-E1 I2C2_SCL PWR_GPIO[1] PWR_GPIO1__IIC2_SCL
J3-B14 I2C2_SDA XGPIOB[14] VIVO_D7__IIC2_SDA
J4-E2 I2C2_SDA PWR_GPIO[2] PWR_GPIO2__IIC2_SDA
J3-B20 I2C4_SCL XGPIOB[20] VIVO_D1__IIC4_SCL
J4-B1 I2C4_SCL XGPIOB[1] ADC3__IIC4_SCL
J3-B21 I2C4_SDA XGPIOB[21] VIVO_D0__IIC4_SDA
J4-B2 I2C4_SDA XGPIOB[2] ADC2__IIC4_SDA
Signed-off-by: Chen Wang <[email protected]>
|
|
fix fdt_ptr error
|
|
[dfs] feat: Mark dirty on unmap for shared mapping
This patch optimizes the pcache varea management by refining the
conditions under which pages are marked dirty, specifically targeting
the unmap operations in the dfs_pcache component. These changes were
necessary to enhance the efficiency of page cache management.
Changes:
- Adjusted include statements in `dfs_pcache.c` for better organization.
- Modified `dfs_aspace_unmap` function:
- Added a check to ensure `varea` is not privately locked before marking a page as dirty.
- Updated `dfs_aspace_page_unmap` function:
- Added a similar check for `varea` lock status before marking a page as dirty.
Signed-off-by: Shell <[email protected]>
|
|
The ADC controller needs to be calibrated during the initialization
phase, otherwise the measured voltage value will be inaccurate.
Signed-off-by: Chen Wang <[email protected]>
|
|
In the new design, we require the user to manually enter the
PinName (as a string) in menuconfig instead of being given
menu items to select.
The original method will lead to too many menu item-related
macros being defined in the code, causing ifdef and other
codes scatter everywhere in the driver code, which is
inconvenient to maintain.
The new design adds a pinmux driver module to manage the
multiplexing of pins. This patch provides this driver module.
P.S., the reason why users are allowed to specify pinname
in a string instead of the pin number is mainly because
the technical manual provided by the SOC manufacturer
does not have numbers for some pins, only names.
Signed-off-by: Chen Wang <[email protected]>
Reviewed-by: Yuanjie He <[email protected]>
Reviewed-by: Shell <[email protected]>
|
|
The contents of the SOC type part in the Kconfig configuration
are retained, and other parts related to I2C pin multiplexing
selection have been rolled back.
Signed-off-by: Chen Wang <[email protected]>
Reviewed-by: Yuanjie He <[email protected]>
Reviewed-by: Shell <[email protected]>
|
|
Add VDSO functionality under the aarch64 architecture
|
|
* [bsp][hpmicro] add weak handle_trap implementation
- added weak handle_trap implementation
Signed-off-by: Fan YANG <[email protected]>
* [libcpu][risc-v][common] remove weak handle_trap function
- removed weak handle_trap function from trap_common.c
Signed-off-by: Fan YANG <[email protected]>
---------
Signed-off-by: Fan YANG <[email protected]>
|
|
The changes unify the tick.c implementations for all risc-v64
architectures, leveraging the CPUTIME feature. This refactoring was
necessary to streamline the codebase, and ensure consistent timer
handling across different platforms.
Changes:
- Updated `Kconfig` in `bsp/cvitek/cv18xx_risc-v` to fix formatting issues.
- Updated .config for BSPs to update `CPUTIME_TIMER_FREQ`
- Updated header of for API `riscv_cputime_init`
- Initialized riscv timer on `rt_hw_tick_init`
- Refactored `tick.c` and `tick.h` in `libcpu/risc-v/t-head/c906` and `libcpu/risc-v/virt64`:
- Replaced direct use of `rdtime` with `clock_cpu_gettime`.
- Removed redundant timer frequency definitions.
- Added static assertions to check the value of `CPUTIME_TIMER_FREQ`.
- Initialized `tick_cycles` based on `CPUTIME_TIMER_FREQ`.
- Integrated `ktime` support for tick initialization.
Signed-off-by: Shell <[email protected]>
Reviewed-on: https://github.com/RT-Thread/rt-thread/pull/9164
Reviewed-by: Chen Wang <[email protected]>
|
|
|
|
fix virtio net rx error
|
|
|
|
|
|
* 移除初始化时未进行引脚初始化就进行引脚设置可能导致的异常
* CS引脚配置判断完善
* xfer返回值优化
|
|
|
|
feat: [libcpu/c906] support ARCH_REMAP_KERNEL
This change was necessary to enable the remapping of the kernel image to
a high virtual address region on the c906 platform.
Changes:
- Introduced new configuration options `ARCH_REMAP_KERNEL`, and
`ARCH_USING_ASID` under the `ARCH_RISCV64` section.
- Updated MMU initialization and switching functions to incorporate
remapping handling.
- Modified page table setup for proper memory attribute settings.
- Added support for early memory setup, kernel remapping
- Added conditional compilation for ASID support in the `rt_aspace` struct,
since this is not enable currently for most architecture.
Signed-off-by: Shell <[email protected]>
|
|
ioremap后地址可能超32位
|
|
|
|
|
|
|
|
修复RX可能导致的内存溢出情况
#8634
|
|
|
|
* [bsp/allwinner] feat: porting to RT_USING_DEVICE_OPS
This patch ports the codebase to use the RT_USING_DEVICE_OPS structure,
which is required by v5.1.0 Smart kernel, improves modularity and makes
it easier to manage device operations by consolidating them into a
single structure, enhancing maintainability and future scalability.
Changes:
- Added RT_USING_DEVICE_OPS conditionals to partition.c and drv_sdmmc.c.
- Defined rt_device_ops structures for partition and sdmmc drivers.
- Updated device initialization to use the ops structure if defined.
- Replaced direct function calls with rt_dev_control, rt_dev_read, and
rt_dev_write macros where applicable.
- Removed redundant us_delay function from os.c.
Signed-off-by: Shell <[email protected]>
* feat: update configuration
* feat: fixup compiler warning
---------
Signed-off-by: Shell <[email protected]>
|
|
Skip configure on open since all configs are copied from the current
configuration on device. So we don't bother to set it back to device
again.
Changes:
- test and skip configuration on open() of tty device
Signed-off-by: Shell <[email protected]>
|
|
|
|
|
|
|
|
|
|
|
|
let cmake generator get more param from `rtconfig.py`
* support getting c/cpp standard from c/cpp compilation flags
* support getting post action and conv it to cmake variable
* add a custom cmake file for user custom settings
* support setting project name from `--project-name=` option
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* 删除tools/kconfiglib文件夹，采用pip安装kconfiglib
* workflows/action_utest.yml添加安装kconfiglib
|
