| Age | Commit message (Collapse) | Author |
|---|
|
When building bsp/cvitek/c906_little, compiler warns:
```
board/board.c: In function 'rt_hw_board_init':
board/board.c:26:5: warning: implicit declaration of
function 'rt_hw_tick_init'; did you mean 'rt_hw_stack_init'?
[-Wimplicit-function-declaration]
26 | rt_hw_tick_init();
| ^~~~~~~~~~~~~~~
| rt_hw_stack_init
board/board.c:29:5: warning: implicit declaration of
function 'rt_hw_uart_init'; did you mean 'rt_hw_board_init'?
[-Wimplicit-function-declaration]
29 | rt_hw_uart_init();
| ^~~~~~~~~~~~~~~
| rt_hw_board_init
```
To remove these build warnings, include header files
which declare these functions.
Plus, remove the decalartion of `tick_isr()`, this
function does not exist.
Signed-off-by: Chen Wang <[email protected]>
|
|
build warning: passing argument 1 of 'inv_icache_range' makes integer
from pointer without a cast [-Wint-conversion]
Analyze: The passed parameter type is void*, which is a pointer type,
but the required type is uintptr_t, which is an integer type. Therefore,
there will be a 'makes integer from pointer without a cast' warning.
Solution: casting the void* pointer to uintptr_t, ensure that the
function receives the correct type.
Signed-off-by: zdtyuiop4444 <[email protected]>
|
|
By default, the small core enables D-Cache without ensuring cache
coherence. Therefore, when using shared memory, inconsistencies can
occur in the data read by the small core and the big core.
Solution: Migrate cache-related functions from the official
duo-buildroot-sdk library to implement cache-related operations in
rthw.h. This allows you to either disable D-Cache or call the
flush_dcache_range function before reading and after writing for
synchronization.
It is recommended to use the flush_dcache_range function, as disabling
D-Cache can have a significant performance impact.
Signed-off-by: zdtyuiop4444 <[email protected]>
|
|
description: In the bsp/cvitek/c906_little/board/interrupt.c, There is an issue with
setting the PLIC_PRIORITY[n].
analysis: PLIC_PRIORITY[n] each register corresponds to the priority of
a hardware interrupt number.
Solution: Each register is 4 bytes.
Multiply the total number of IRQs by 4 instead of dividing by 4.
Signed-off-by: Liu Gui <[email protected]>
|
|
fix milkv-duos-sd cann't startup big-core kernel
milkv-duos-sd use cv1813h folder store ld file
Signed-off-by: flyingcys <[email protected]>
|
|
|
|
Signed-off-by: Shicheng Chu <[email protected]>
|
|
Analysis: Some macro definition names are not standardized
and lack prefixes.
Solution: Add BSP_ prefix to GPIO_IRQ_BASE SYS_GPIO_IRQ_BASE
PLIC_PHY_ADDR TIMER_CLK_FREQ UART_IRQ_BASE I2C_IRQ_BASE.
Signed-off-by: Shicheng Chu <[email protected]>
|
|
Analysis: The IRQ_MAX_NR value of c906_little is wrong.
interrupt.h relies on IRQ_MAX_NR defined in rtconfig.h but
does not explicitly include this header file.
Solution: Change IRQ_MAX_NR to the correct value 61 in
the datasheet. Explicitly include rtconfig.h in interrupt.h.
Signed-off-by: Shicheng Chu <[email protected]>
Reviewed-by: Chen Wang <[email protected]>
|
|
Signed-off-by: Chen Wang <[email protected]>
|
|
Board level pin available info:
duo & duo256:
NAME SPI CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP6 SPI2_SCK PWR_GPIO[23] SD1_CLK__SPI2_SCK
GP7 SPI2_SDO PWR_GPIO[22] SD1_CMD__SPI2_SDO
GP8 SPI2_SDI PWR_GPIO[21] SD1_D0__SPI2_SDI
GP9 SPI2_CS_X PWR_GPIO[18] SD1_D3__SPI2_CS_X
Signed-off-by: Chen Wang <[email protected]>
|
|
Board level pin available info is summarized and list here for memo:
Duo:
NAME PWM CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
PWM-1
GP9 PWM4 PWR_GPIO[18] SD1_D3__PWM_4
GP12 PWM4 XGPIOA[16] UART0_TX__PWM_4
GP4 PWM5 PWR_GPIO[19] SD1_D2__PWM_5
GP13 PWM5 XGPIOA[17] UART0_RX__PWM_5
GP5 PWM6 PWR_GPIO[20] SD1_D1__PWM_6
GP8 PMW7 PWR_GPIO[21] SD1_D0__PWM_7
PWM-2
GP7 PWM8 PWR_GPIO[22] SD1_CMD__PWM_8
GP6 PWM9 PWR_GPIO[23] SD1_CLK__PWM_9
GP2 PWM10 PWR_GPIO[26] SD1_GPIO1__PWM_10
GP3 PWM11 PWR_GPIO[25] SD1_GPIO0__PWM_11
Duo256:
NAME PWM CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
PWM-1
GP9 PWM4 PWR_GPIO[18] SD1_D3__PWM_4
GP12 PWM4 XGPIOA[16] UART0_TX__PWM_4
GP4 PWM5 PWR_GPIO[19] SD1_D2__PWM_5
GP13 PWM5 XGPIOA[17] UART0_RX__PWM_5
GP3 PWM6 XGPIOA[18] JTAG_CPU_TCK__PWM_6
GP5 PWM6 PWR_GPIO[20] SD1_D1__PWM_6
GP2 PWM7 XGPIOA[19] JTAG_CPU_TMS__PWM_7
GP8 PMW7 PWR_GPIO[21] SD1_D0__PWM_7
PWM-2
GP7 PWM8 PWR_GPIO[22] SD1_CMD__PWM_8
GP6 PWM9 PWR_GPIO[23] SD1_CLK__PWM_9
GP10 PWM10 XGPIOC[14] PAD_MIPI_TXM1__PWM_10
GP11 PWM11 XGPIOC[15] PAD_MIPI_TXP1__PWM_11
Signed-off-by: Chen Wang <[email protected]>
|
|
Board level UART pinmux summary, following capability
should be controlled by pinname whitelist.
Duo:
NAME UART CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP13 UART0_RX XGPIOA[17] UART0_RX__UART0_RX
GP12 UART0_TX XGPIOA[16] UART0_TX__UART0_TX
GP1 UART1_RX XGPIOA[29] IIC0_SDA__UART1_RX
GP13 UART1_RX XGPIOA[17] UART0_RX__UART1_RX
GP0 UART1_TX XGPIOA[28] IIC0_SCL__UART1_TX
GP12 UART1_TX XGPIOA[16] UART0_TX__UART1_TX
GP1 UART2_RX XGPIOA[29] IIC0_SDA__UART2_RX
GP5 UART2_RX PWR_GPIO[20] SD1_D1__UART2_RX
GP0 UART2_TX XGPIOA[28] IIC0_SCL__UART2_TX
GP4 UART2_TX PWR_GPIO[19] SD1_D2__UART2_TX
GP5 UART3_RX PWR_GPIO[20] SD1_D1__UART3_RX
GP4 UART3_TX PWR_GPIO[19] SD1_D2__UART3_TX
GP3 UART4_RX PWR_GPIO[25] SD1_GPIO0__UART4_RX
GP2 UART4_TX PWR_GPIO[26] SD1_GPIO1__UART4_TX
Duo 256m:
NAME UART CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP13 UART0_RX XGPIOA[17] UART0_RX__UART0_RX
GP12 UART0_TX XGPIOA[16] UART0_TX__UART0_TX
GP1 UART1_RX XGPIOA[29] IIC0_SDA__UART1_RX
GP3 UART1_RX XGPIOA[18] JTAG_CPU_TCK__UART1_RX
GP13 UART1_RX XGPIOA[17] UART0_RX__UART1_RX
GP0 UART1_TX XGPIOA[28] IIC0_SCL__UART1_TX
GP2 UART1_TX XGPIOA[19] JTAG_CPU_TMS__UART1_TX
GP12 UART1_TX XGPIOA[16] UART0_TX__UART1_TX
GP1 UART2_RX XGPIOA[29] IIC0_SDA__UART2_RX
GP5 UART2_RX PWR_GPIO[20] SD1_D1__UART2_RX
GP0 UART2_TX XGPIOA[28] IIC0_SCL__UART2_TX
GP4 UART2_TX PWR_GPIO[19] SD1_D2__UART2_TX
GP5 UART3_RX PWR_GPIO[20] SD1_D1__UART3_RX
GP4 UART3_TX PWR_GPIO[19] SD1_D2__UART3_TX
Note: this patch also update the .config and rtconfig.h
because this patch modify some configuration items's name,
for example: RT_USIMG_UART0 -> BSP_USING_UART0.
FIXME: only handle RISC-V related, no ARM.
Signed-off-by: Chen Wang <[email protected]>
|
|
Based on new pinmux framework, add configuration for uart.
Board level pin available info is summarized and should be
controlled by pin whitelist.
Duo
NAME I2C CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP0 I2C0_SCL XGPIOA[28] IIC0_SCL__IIC0_SCL
GP1 I2C0_SDA XGPIOA[29] IIC0_SDA__IIC0_SDA
GP4 I2C1_SCL PWR_GPIO[19] SD1_D2__IIC1_SCL
GP9 I2C1_SCL PWR_GPIO[18] SD1_D3__IIC1_SCL
GP11 I2C1_SCL XGPIOC[10] PAD_MIPIRX0N__IIC1_SCL
GP5 I2C1_SDA PWR_GPIO[20] SD1_D1__IIC1_SDA
GP8 I2C1_SDA PWR_GPIO[21] SD1_D0__IIC1_SDA
GP10 I2C1_SDA XGPIOC[9] PAD_MIPIRX1P__IIC1_SDA
GP7 I2C3_SCL PWR_GPIO[22] SD1_CMD__IIC3_SCL
GP6 I2C3_SDA PWR_GPIO[23] SD1_CLK__IIC3_SDA
Duo256m
NAME I2C CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP4 I2C1_SCL PWR_GPIO[19] SD1_D2__IIC1_SCL
GP9 I2C1_SCL PWR_GPIO[18] SD1_D3__IIC1_SCL
GP5 I2C1_SDA PWR_GPIO[20] SD1_D1__IIC1_SDA
GP8 I2C1_SDA PWR_GPIO[21] SD1_D0__IIC1_SDA
GP11 I2C2_SCL XGPIOC[15] PAD_MIPI_TXP1__IIC2_SCL
GP10 I2C2_SDA XGPIOC[14] PAD_MIPI_TXM1__IIC2_SDA
GP7 I2C3_SCL PWR_GPIO[22] SD1_CMD__IIC3_SCL
GP6 I2C3_SDA PWR_GPIO[23] SD1_CLK__IIC3_SDA
Duo S(Note, we have not supported duo S, just list for memo)
NAME I2C CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
J3-B18 I2C1_SCL XGPIOB[18] VIVO_D3__IIC1_SCL
J3-B12 I2C1_SCL XGPIOB[12] VIVO_D9__IIC1_SCL
J3-B11 I2C1_SDA XGPIOB[11] VIVO_D10__IIC1_SDA
J3-B13 I2C2_SCL XGPIOB[13] VIVO_D8__IIC2_SCL
J4-E1 I2C2_SCL PWR_GPIO[1] PWR_GPIO1__IIC2_SCL
J3-B14 I2C2_SDA XGPIOB[14] VIVO_D7__IIC2_SDA
J4-E2 I2C2_SDA PWR_GPIO[2] PWR_GPIO2__IIC2_SDA
J3-B20 I2C4_SCL XGPIOB[20] VIVO_D1__IIC4_SCL
J4-B1 I2C4_SCL XGPIOB[1] ADC3__IIC4_SCL
J3-B21 I2C4_SDA XGPIOB[21] VIVO_D0__IIC4_SDA
J4-B2 I2C4_SDA XGPIOB[2] ADC2__IIC4_SDA
Signed-off-by: Chen Wang <[email protected]>
|
|
The contents of the SOC type part in the Kconfig configuration
are retained, and other parts related to I2C pin multiplexing
selection have been rolled back.
Signed-off-by: Chen Wang <[email protected]>
Reviewed-by: Yuanjie He <[email protected]>
Reviewed-by: Shell <[email protected]>
|
|
* bsp: cvitek: kconfig: add wdt for cv18xx_riscv
Add Watchdog timer in Kconfig.
Signed-off-by: Chen Wang <[email protected]>
* drv: cvitek: remove using macro from source file
Building of source file should be controlled by SConscript,
but not in source file itself.
Signed-off-by: Chen Wang <[email protected]>
* bsp: cvitek: kconfig: add i2c for cv18xx_riscv
Add I2C in Kconfig for c906B.
Note, the IRQ# is different from that of c906L.
Signed-off-by: Chen Wang <[email protected]>
* bsp: cvitek: kconfig: add rtc for cv18xx_riscv
Add RTC in Kconfig for c906B.
Signed-off-by: Chen Wang <[email protected]>
* bsp: cvitek: fix channel issue for pwm driver
The original code confuses the concepts of controllers and channels.
Fixed it and do some code cleanup.
Signed-off-by: Chen Wang <[email protected]>
* bsp:cvitek: add i2c pinmux config for cv18xx_riscv
Pinmux in driver code is controlled by SOC type, bcos driver
code should be general and support all pins defined by SoC.
Pinmux configuration in Kconfig is controlled by BOARD type,
bcos when we operate on board, it does not expose all chip-level
pin signals and we can only use part of them.
Following is I2C signals exported by duo family. Details see
https://milkv.io/docs/duo/overview.
Note: we have not added support for duo-S.
Duo
===
NAME I2C CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP0 I2C0_SCL XGPIOA[28] IIC0_SCL__IIC0_SCL
GP1 I2C0_SDA XGPIOA[29] IIC0_SDA__IIC0_SDA
GP4 I2C1_SCL PWR_GPIO[19] SD1_D2__IIC1_SCL
GP9 I2C1_SCL PWR_GPIO[18] SD1_D3__IIC1_SCL
GP11 I2C1_SCL XGPIOC[10] PAD_MIPIRX0N__IIC1_SCL
GP5 I2C1_SDA PWR_GPIO[20] SD1_D1__IIC1_SDA
GP8 I2C1_SDA PWR_GPIO[21] SD1_D0__IIC1_SDA
GP10 I2C1_SDA XGPIOC[9] PAD_MIPIRX1P__IIC1_SDA
GP7 I2C3_SCL PWR_GPIO[22] SD1_CMD__IIC3_SCL
GP6 I2C3_SDA PWR_GPIO[23] SD1_CLK__IIC3_SDA
Duo 256m
========
NAME I2C CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
GP4 I2C1_SCL PWR_GPIO[19] SD1_D2__IIC1_SCL
GP9 I2C1_SCL PWR_GPIO[18] SD1_D3__IIC1_SCL
GP5 I2C1_SDA PWR_GPIO[20] SD1_D1__IIC1_SDA
GP8 I2C1_SDA PWR_GPIO[21] SD1_D0__IIC1_SDA
GP11 I2C2_SCL XGPIOC[15] PAD_MIPI_TXP1__IIC2_SCL
GP10 I2C2_SDA XGPIOC[14] PAD_MIPI_TXM1__IIC2_SDA
GP7 I2C3_SCL PWR_GPIO[22] SD1_CMD__IIC3_SCL
GP6 I2C3_SDA PWR_GPIO[23] SD1_CLK__IIC3_SDA
Duo S
=====
NAME I2C CV1800B/GPIO <PINNAME>__<FUNCNAME>
---- --- ------------ ---------------------
J3-B18 I2C1_SCL XGPIOB[18] VIVO_D3__IIC1_SCL
J3-B12 I2C1_SCL XGPIOB[12] VIVO_D9__IIC1_SCL
J3-B11 I2C1_SDA XGPIOB[11] VIVO_D10__IIC1_SDA
J3-B13 I2C2_SCL XGPIOB[13] VIVO_D8__IIC2_SCL
J4-E1 I2C2_SCL PWR_GPIO[1] PWR_GPIO1__IIC2_SCL
J3-B14 I2C2_SDA XGPIOB[14] VIVO_D7__IIC2_SDA
J4-E2 I2C2_SDA PWR_GPIO[2] PWR_GPIO2__IIC2_SDA
J3-B20 I2C4_SCL XGPIOB[20] VIVO_D1__IIC4_SCL
J4-B1 I2C4_SCL XGPIOB[1] ADC3__IIC4_SCL
J3-B21 I2C4_SDA XGPIOB[21] VIVO_D0__IIC4_SDA
J4-B2 I2C4_SDA XGPIOB[2] ADC2__IIC4_SDA
Signed-off-by: Chen Wang <[email protected]>
Signed-off-by: flyingcys <[email protected]>
* bsp:cvitek: remove using macro from source file for i2c
Signed-off-by: Chen Wang <[email protected]>
* bsp:cvitek: unify menu message text for i2c as other drivers
Other dirvers has no extra word "HW".
Signed-off-by: Chen Wang <[email protected]>
* bsp:cvitek: add i2c pinmux config for c906_little
Porting what we have done in commit "bsp:cvitek: add i2c pinmux config
for cv18xx_riscv" to c906_little.
Signed-off-by: Chen Wang <[email protected]>
---------
Signed-off-by: Chen Wang <[email protected]>
Signed-off-by: flyingcys <[email protected]>
Co-authored-by: flyingcys <[email protected]>
|
|
Signed-off-by: Jingbao Qiu <[email protected]>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
