summaryrefslogtreecommitdiff
path: root/components/drivers
AgeCommit message (Collapse)Author
2020-06-11[Sensor] Add Plantower sensor infoluhuadong
2020-06-10[ drivers/usb]Fixed a bug may cause stackover flowDavid Lin
2020-06-02[W25Q32BV]Support fast read QUAD_OUTPUT and QUAL_IO.Wayne Lin
2020-05-30Merge pull request #3601 from OpenNuvoton/rtt_issuesBernard Xiong
Fix issues
2020-05-20Fix rt_hw_inputcapture_isr public function name in header file.Wayne Lin
Fix miss-break in HWTIMER_CTRL_INFO_GET case.
2020-05-19[drivers][watchdog] 修复watchdog.c 注释的一处笔误GaoJie
2020-05-15Merge branch 'master' of https://github.com/rt-thread/rt-thread into rtt_issuesWayne Lin
2020-05-04Merge pull request #3565 from OpenNuvoton/rtt_issuesBernard Xiong
Get stuck issue after open-close-open CAN device.
2020-05-02add vendor information of sensorPrry
2020-05-01Merge pull request #3569 from egbert-h/masterBernard Xiong
mstorage.c: fix the issue bug in_read_capacity()
2020-04-30Rename usbd and usbh source files for IAR building issue.Wayne Lin
2020-04-28mstorage.c: fix the issue that _read_capacity() returns the wrong last valid ↵hphuang
address of storage medium
2020-04-27Get stuck issue after open-close-open CAN device.Wayne Lin
Signed-off-by: Wayne Lin <[email protected]>
2020-04-13Update pipe.cDavid Lin
2020-04-12[components/drivers] update pipe.cDavid Lin
Fixed stackover flow bug when create pipe->fifo
2020-04-11Fix some spelling mistakesDeclanHuaChen
2020-04-10[components][serial]关闭uart时，反初始化tx_dma->data_queue，防止� ↵yangjie
��存泄漏
2020-04-10Merge pull request #3503 from yangjie11/yj_devBernard Xiong
[components][dataqueue]add rt_data_queue_deinit
2020-04-10Merge pull request #3425 from DavidLin1577/patch-1Bernard Xiong
Fixed wrong output information
2020-04-08[components][dataqueue]修改is_init为magic数yangjie
2020-04-07[components][dataqueue]add rt_data_queue_deinityangjie
2020-03-30Merge pull request #3484 from qz721/masterBernard Xiong
修复USB不能正常识别composite设备的bug
2020-03-26Merge pull request #3472 from DavidLin1577/patch-2Bernard Xiong
[components/usb]Fixed a stack overflow bug
2020-03-26修复USB不能正常识别composite设备的bugqz721
2020-03-23[optimize] stm32 uart driverSummerGift
2020-03-21Update hub.cDavid Lin
2020-03-21Update cdc_vcom.cDavid Lin
2020-03-21Update ecm.cDavid Lin
2020-03-21Merge pull request #3427 from DavidLin1577/patch-2Bernard Xiong
Fixed typos in Kconfig
2020-03-16Merge pull request #3397 from luhuadong/developBernard Xiong
[Sensor] Support custom commands for rt_sensor_control
2020-03-16Merge pull request #3458 from shawn1221/mmc-upstream-20200316Bernard Xiong
component: sdio: fix potential ricky clock setting
2020-03-16Merge pull request #3456 from zhao0116/spiBernard Xiong
spi: support slave mode and master mode runtime config
2020-03-16component: sdio: fix potential ricky clock settingShawn Lin
Currently RTT mmc stack only support Highspeed mode or blow, which means the max speed should be 52MHz according to JEDEC spec. Two problems show here: (1) max_data_rate = (unsigned int)-1. The value of unsigned int depends on compilers/arch. Moreover, it makes no sense to assume cpu addressing width with IP clock rate limit. (1)hs_max_data_rate was set to 200MHz. So what should BSP drivers do if 52MHz < max_data_rate < 200MHz? Either it blindly sets a spec-violated clock rate to drive a Highspeed card, or just adjust the clock rate internally. Both cases are really bad for practice. If the card claims to support Highspeed, we set the clock to not to exceed 52MHz. Otherwise it should be set according to card->max_data_rate parsed by ext_csd. This patch fixes it as-is, and also simplify the code a lot. Signed-off-by: Shawn Lin <[email protected]>
2020-03-16[Sensor] Add user-commands range limitationluhuadong
2020-03-16Support msc mode automatic switchingCliff Chen
Signed-off-by: Cliff Chen <[email protected]>
2020-03-16spi: support slave mode and master mode runtime configYifeng Zhao
support slave mode and master mode runtime config. Change-Id: Iabadbade8997bb8e3adef8ce95f6c45f6bb35329 Signed-off-by: Yifeng Zhao <[email protected]>
2020-03-12[Components] sdio: try bus width depends on host's capabilityShawn Lin
It makes no sense to try bus width if not supported by drivers or BSP, since we know it must be failed. It saves a lot for booting in time critical environment. Signed-off-by: Shawn Lin <[email protected]>
2020-03-12[component] sdio: Fix mmc mount function if the whole device is a partitionShawn Lin
If the whole sd card was formatted as a partition, current code break out the loop mistakenly, so it skips dfs_mount_device later. Simply remove the broken 'break' to solve this problem. Signed-off-by: Shawn Lin <[email protected]>
2020-03-08Fixed wrong output information in core.cDavid Lin
rt_kprintf("alloc memery failed\n"); -> rt_kprintf("alloc memory failed\n");
2020-03-05Fixed typos in KconfigDavid Lin
mesage -> message memmory -> memory
2020-03-04Fixed wrong output informationDavid Lin
to ->too
2020-03-04Fixed wrong output informationDavid Lin
to -> too
2020-03-04Merge pull request #3413 from luhuadong/patch1Bernard Xiong
[Sensor] Add vendor info and sensor types for cmd
2020-02-29[driver][wlan] add raw frame send interface and Management frame filter ↵chenyong
interface Signed-off-by: chenyong <[email protected]>
2020-02-28fix raspi3-64 sdio driverbigmagic
2020-02-26[Sensor] fixed %% printluhuadong
2020-02-26[Sensor] Add vendor info and sensor types for cmdluhuadong
2020-02-23Update sd.cA.orz
clean #if 0 code
2020-02-22add change logluhuadong
2020-02-22[Sensor] Support custom commands for rt_sensor_controlluhuadong
generated by cgit v1.3.1 (git 2.54.0) at 2026-10-25 15:33:26 +0000