menu "Hardware Drivers Config" menu "Onboard Peripheral Drivers" config BSP_USING_STLINK_TO_USART bool "Enable STLINK TO USART (uart2)" select BSP_USING_UART select BSP_USING_UART2 default y config BSP_USING_ARDUINO bool "Compatible with Arduino Ecosystem (RTduino)" select PKG_USING_RTDUINO select BSP_USING_STLINK_TO_USART select BSP_USING_GPIO select BSP_USING_TIM select BSP_USING_TIM9 select BSP_USING_ADC select BSP_USING_ADC1 select BSP_USING_PWM select BSP_USING_PWM1 select BSP_USING_PWM1_CH1 select BSP_USING_PWM2 select BSP_USING_PWM2_CH2 select BSP_USING_PWM2_CH3 select BSP_USING_PWM3 select BSP_USING_PWM3_CH1 select BSP_USING_PWM3_CH2 select BSP_USING_PWM4 select BSP_USING_PWM4_CH1 select RT_USING_I2C select BSP_USING_SOFT_I2C select BSP_USING_SOFT_I2C1 select BSP_USING_SPI select BSP_USING_SPI1 select BSP_SPI1_TX_USING_DMA select BSP_SPI1_RX_USING_DMA select RTDUINO_USING_WIRE select RTDUINO_USING_SPI imply RTDUINO_USING_SERVO default n config RT_SOFT_I2C1_HAS_PIN_DEFAULT bool default y if RT_USING_SOFT_I2C1 config RT_SOFT_I2C1_SCL_PIN_DEFAULT int default 24 if RT_USING_SOFT_I2C1 config RT_SOFT_I2C1_SDA_PIN_DEFAULT int default 25 if RT_USING_SOFT_I2C1 endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default n select RT_USING_SERIAL if BSP_USING_UART config BSP_STM32_UART_V1_TX_TIMEOUT int "UART TX timeout" default 2000 depends on RT_USING_SERIAL_V1 menuconfig BSP_USING_UART2 bool "Enable UART2" default n if BSP_USING_UART2 config BSP_UART2_RX_USING_DMA bool "Enable UART2 RX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_UART2_TX_USING_DMA bool "Enable UART2 TX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_UART2_RX_BUFSIZE int "Set UART2 RX buffer size" range 64 65535 depends on RT_USING_SERIAL_V2 default 256 config BSP_UART2_TX_BUFSIZE int "Set UART2 TX buffer size" range 0 65535 depends on RT_USING_SERIAL_V2 default 0 config BSP_UART2_DMA_PING_BUFSIZE int "Set UART2 RX DMA ping-pong buffer size" range 32 65535 depends on RT_USING_SERIAL_V2 && BSP_UART2_RX_USING_DMA default 64 endif endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_TIM bool "Enable timer" default n select RT_USING_CLOCK_TIME if BSP_USING_TIM config BSP_USING_TIM9 bool "Enable TIM9" default n config BSP_USING_TIM11 bool "Enable TIM11" default n endif menuconfig BSP_USING_PWM bool "Enable PWM" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM1 bool "Enable timer1 output PWM" default n if BSP_USING_PWM1 config BSP_USING_PWM1_CH1 bool "Enable PWM1 channel1" default n config BSP_USING_PWM1_CH4 bool "Enable PWM1 channel4" default n endif menuconfig BSP_USING_PWM2 bool "Enable timer2 output PWM" default n if BSP_USING_PWM2 config BSP_USING_PWM2_CH2 bool "Enable PWM2 channel2" default n config BSP_USING_PWM2_CH3 bool "Enable PWM2 channel3" default n endif menuconfig BSP_USING_PWM3 bool "Enable timer3 output PWM" default n if BSP_USING_PWM3 config BSP_USING_PWM3_CH1 bool "Enable PWM3 channel1" default n config BSP_USING_PWM3_CH2 bool "Enable PWM3 channel2" default n endif menuconfig BSP_USING_PWM4 bool "Enable timer4 output PWM" default n if BSP_USING_PWM4 config BSP_USING_PWM4_CH1 bool "Enable PWM4 channel1" default n endif endif menuconfig BSP_USING_SPI bool "Enable SPI BUS" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI1 bool "Enable SPI1 BUS" default n config BSP_SPI1_TX_USING_DMA bool "Enable SPI1 TX DMA" depends on BSP_USING_SPI1 default n config BSP_SPI1_RX_USING_DMA bool "Enable SPI1 RX DMA" depends on BSP_USING_SPI1 select BSP_SPI1_TX_USING_DMA default n config BSP_USING_SPI3 bool "Enable SPI3 BUS" default n config BSP_SPI3_TX_USING_DMA bool "Enable SPI3 TX DMA" depends on BSP_USING_SPI3 default n config BSP_SPI3_RX_USING_DMA bool "Enable SPI3 RX DMA" depends on BSP_USING_SPI3 select BSP_SPI3_TX_USING_DMA default n endif menuconfig BSP_USING_SOFT_I2C bool "Enable software I2C (swi2c)" default n select RT_USING_I2C select RT_USING_SOFT_I2C if BSP_USING_SOFT_I2C menuconfig BSP_USING_SOFT_I2C1 bool "Enable software I2C1 Bus (swi2c1)" default n select RT_USING_SOFT_I2C1 if BSP_USING_SOFT_I2C1 config RT_SOFT_I2C1_SCL_PIN int "swi2c1 SCL pin number" default 24 config RT_SOFT_I2C1_SDA_PIN int "swi2c1 SDA pin number" default 25 endif endif source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig" endmenu menu "Board extended module Drivers" endmenu endmenu