menu "Hardware Drivers Config" menu "Onboard Peripheral Drivers" config BSP_USING_COM2 bool "Enable COM2(485)" select BSP_USING_UART select BSP_USING_UART2 select RT_USING_I2C select BSP_USING_SOFT_I2C select BSP_USING_SOFT_I2C1 select PKG_USING_PCF8574 default n config BSP_USING_SDRAM bool "Enable SDRAM" select BSP_USING_FMC default n config BSP_USING_LCD bool "Enable LCD" select BSP_USING_LTDC select BSP_USING_SDRAM default n config BSP_USING_QSPI_FLASH bool "Enable QSPI FLASH (W25Q256 qspi)" select BSP_USING_QSPI select RT_USING_SFUD select RT_SFUD_USING_QSPI default n config BSP_USING_SDMMC bool "Enable SDMMC (SD card)" select RT_USING_SDIO select RT_USING_DFS select RT_USING_DFS_ELMFAT default n config BSP_USING_OV2640 bool "Enable camera (ov2640)" select BSP_USING_DCMI select RT_USING_I2C select BSP_USING_SOFT_I2C select BSP_USING_SOFT_I2C2 default n config RT_SOFT_I2C1_HAS_PIN_DEFAULT bool default y if RT_USING_SOFT_I2C1 config RT_SOFT_I2C1_SCL_PIN_DEFAULT int default 116 if RT_USING_SOFT_I2C1 config RT_SOFT_I2C1_SDA_PIN_DEFAULT int default 117 if RT_USING_SOFT_I2C1 config RT_SOFT_I2C2_HAS_PIN_DEFAULT bool default y if RT_USING_SOFT_I2C2 config RT_SOFT_I2C2_SCL_PIN_DEFAULT int default 127 if RT_USING_SOFT_I2C2 config RT_SOFT_I2C2_SDA_PIN_DEFAULT int default 125 if RT_USING_SOFT_I2C2 endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL if BSP_USING_UART config BSP_STM32_UART_V1_TX_TIMEOUT int "UART TX timeout" default 6000 depends on RT_USING_SERIAL_V1 menuconfig BSP_USING_UART1 bool "Enable UART1" default y if BSP_USING_UART1 config BSP_UART1_RX_BUFSIZE int "Set UART1 RX buffer size" range 64 65535 depends on RT_USING_SERIAL_V2 default 256 config BSP_UART1_TX_BUFSIZE int "Set UART1 TX buffer size" range 0 65535 depends on RT_USING_SERIAL_V2 default 0 config BSP_UART1_DMA_PING_BUFSIZE int "Set UART1 RX DMA ping-pong buffer size" range 32 65535 depends on RT_USING_SERIAL_V2 && BSP_UART1_RX_USING_DMA default 64 endif menuconfig BSP_USING_UART2 bool "Enable UART2" default n if BSP_USING_UART2 config BSP_UART2_RX_USING_DMA bool "Enable UART2 RX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_UART2_TX_USING_DMA bool "Enable UART2 TX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_UART2_RX_BUFSIZE int "Set UART2 RX buffer size" range 64 65535 depends on RT_USING_SERIAL_V2 default 256 config BSP_UART2_TX_BUFSIZE int "Set UART2 TX buffer size" range 0 65535 depends on RT_USING_SERIAL_V2 default 0 config BSP_UART2_DMA_PING_BUFSIZE int "Set UART2 RX DMA ping-pong buffer size" range 32 65535 depends on RT_USING_SERIAL_V2 && BSP_UART2_RX_USING_DMA default 64 endif endif config BSP_USING_FMC bool default n config BSP_USING_LTDC bool default n menuconfig BSP_USING_SPI bool "Enable SPI BUS" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI2 bool "Enable SPI2 BUS" default n endif config BSP_USING_QSPI bool "Enable QSPI BUS" select RT_USING_QSPI select RT_USING_SPI default n menuconfig BSP_USING_SOFT_I2C bool "Enable software I2C (swi2c)" default n select RT_USING_I2C select RT_USING_SOFT_I2C if BSP_USING_SOFT_I2C menuconfig BSP_USING_SOFT_I2C1 bool "Enable software I2C1 Bus (swi2c1)" default n select RT_USING_SOFT_I2C1 if BSP_USING_SOFT_I2C1 config RT_SOFT_I2C1_SCL_PIN int "swi2c1 SCL pin number" default 116 config RT_SOFT_I2C1_SDA_PIN int "swi2c1 SDA pin number" default 117 endif menuconfig BSP_USING_SOFT_I2C2 bool "Enable software I2C2 Bus (swi2c2)" default n select RT_USING_SOFT_I2C2 if BSP_USING_SOFT_I2C2 config RT_SOFT_I2C2_SCL_PIN int "swi2c2 SCL pin number" default 127 config RT_SOFT_I2C2_SDA_PIN int "swi2c2 SDA pin number" default 125 endif endif config BSP_USING_ON_CHIP_FLASH bool "Enable on-chip FLASH" default n config BSP_USING_DCMI bool "Enable DCMI" default n menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC default n if BSP_USING_ONCHIP_RTC choice BSP_RTC_LS_SEL prompt "Select clock source" default BSP_RTC_USING_LSE config BSP_RTC_USING_LSE bool "RTC USING LSE" config BSP_RTC_USING_LSI bool "RTC USING LSI" endchoice endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_DAC bool "Enable DAC" default n select RT_USING_DAC if BSP_USING_DAC config BSP_USING_DAC1 bool "Enable DAC1" default n endif config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig" endmenu menu "Board extended module Drivers" endmenu endmenu