menu "Hardware Drivers Config" config SOC_STM32H750_ARTPI bool default y menu "Board extended module" menuconfig ART_PI_USING_MEDIA_IO bool "Media-IO" default n if ART_PI_USING_MEDIA_IO config BSP_USING_SPI_LCD_ILI9488 bool config PKG_USING_PERSIMMON_SRC bool config MEDIA_IO_USING_SCREEN select BSP_USING_SPI select BSP_USING_SPI2 select BSP_USING_SDRAM select BSP_USING_SPI_LCD_ILI9488 select PKG_USING_PERSIMMON_SRC bool "Enable Screen" default y if MEDIA_IO_USING_SCREEN config BSP_USING_LVGL bool "Enable LVGL for LCD" select BSP_USING_SPI_LCD_ILI9488 select PKG_USING_LVGL select PKG_USING_LV_MUSIC_DEMO default n endif config MEDIA_IO_USING_TOUCH select RT_USING_I2C select BSP_USING_SOFT_I2C select BSP_USING_SOFT_I2C2 select BSP_USING_SOFT_I2C3 select PKG_USING_FT6236 bool "Enable Touch" default y config MEDIA_IO_USING_AUDIO select RT_USING_AUDIO select RT_USING_I2C bool "Enable Audio" default y if MEDIA_IO_USING_AUDIO config AUDIO_MP3 bool "Support MP3" select PKG_USING_HELIX default y endif endif menuconfig ART_PI_USING_INDUSTRY_IO bool "Industry-IO" default n if ART_PI_USING_INDUSTRY_IO config INDUSTRY_IO_USING_ETH select BSP_USING_ETH select PHY_USING_LAN8720A select BSP_USING_ETH_H750 bool "Enable Ethernet" default y endif endmenu menu "Onboard Peripheral Drivers" config BSP_USING_USB_TO_USART bool "Enable Debuger USART (uart4)" select BSP_USING_UART select BSP_USING_UART4 default n config BSP_USING_SPI_FLASH bool "Enable SPI FLASH (spi1)" select BSP_USING_SPI select BSP_USING_SPI1 select RT_USING_FAL select FAL_USING_SFUD_PORT select RT_USING_SFUD default n config BSP_USING_QSPI_FLASH bool "Enable QSPI FLASH (w25q64 qspi)" select BSP_USING_QSPI select FAL_USING_SFUD_PORT select RT_USING_SFUD select RT_SFUD_USING_QSPI default n menuconfig BSP_USING_FS bool "Enable filesystem" select RT_USING_DFS select RT_USING_DFS_ROMFS default n if BSP_USING_FS config BSP_USING_SDCARD_FS bool "Enable SDCARD filesystem" select BSP_USING_SDIO_ARTPI select BSP_USING_SDIO1 select RT_USING_DFS_ELMFAT default n config BSP_USING_SPI_FLASH_FS bool "Enable SPI FLASH filesystem" select BSP_USING_SPI_FLASH select RT_USING_MTD_NOR select PKG_USING_LITTLEFS default n endif config BSP_USING_WIFI bool "Enable wifi (AP6212)" select ART_PI_USING_WIFI_6212_LIB select BSP_USING_SPI_FLASH select RT_USING_WIFI select RT_USING_SAL default n config RT_SOFT_I2C2_HAS_PIN_DEFAULT bool default y if RT_USING_SOFT_I2C2 config RT_SOFT_I2C2_SCL_PIN_DEFAULT int default 127 if RT_USING_SOFT_I2C2 config RT_SOFT_I2C2_SDA_PIN_DEFAULT int default 125 if RT_USING_SOFT_I2C2 config RT_SOFT_I2C3_HAS_PIN_DEFAULT bool default y if RT_USING_SOFT_I2C3 config RT_SOFT_I2C3_SCL_PIN_DEFAULT int default 123 if RT_USING_SOFT_I2C3 config RT_SOFT_I2C3_SDA_PIN_DEFAULT int default 124 if RT_USING_SOFT_I2C3 endmenu menu "On-chip Peripheral Drivers" config BSP_SCB_ENABLE_I_CACHE bool "Enable ICACHE" default y config BSP_SCB_ENABLE_D_CACHE bool "Enable DCACHE" default y config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default n select RT_USING_SERIAL select RT_SERIAL_USING_DMA if BSP_USING_UART config BSP_STM32_UART_V1_TX_TIMEOUT int "UART TX timeout" default 6000 depends on RT_USING_SERIAL_V1 menuconfig BSP_USING_UART1 bool "Enable UART1" default n if BSP_USING_UART1 config BSP_UART1_RX_USING_DMA bool "Enable UART1 RX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_UART1_TX_USING_DMA bool "Enable UART1 TX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_UART1_RX_BUFSIZE int "Set UART1 RX buffer size" range 64 65535 depends on BSP_USING_UART1 default 256 config BSP_UART1_TX_BUFSIZE int "Set UART1 TX buffer size" range 0 65535 depends on BSP_USING_UART1 default 0 config BSP_UART1_DMA_PING_BUFSIZE int "Set UART1 RX DMA ping-pong buffer size" range 32 65535 depends on RT_USING_SERIAL_V2 && BSP_UART1_RX_USING_DMA default 64 endif menuconfig BSP_USING_UART3 bool "Enable UART3" default n if BSP_USING_UART3 config BSP_UART3_RX_BUFSIZE int "Set UART3 RX buffer size" range 64 65535 depends on BSP_USING_UART3 default 256 config BSP_UART3_TX_BUFSIZE int "Set UART3 TX buffer size" range 0 65535 depends on BSP_USING_UART3 default 0 endif menuconfig BSP_USING_UART4 bool "Enable UART4" default n if BSP_USING_UART4 config BSP_UART4_RX_BUFSIZE int "Set UART4 RX buffer size" range 64 65535 depends on BSP_USING_UART4 default 256 config BSP_UART4_TX_BUFSIZE int "Set UART4 TX buffer size" range 0 65535 depends on BSP_USING_UART4 default 0 endif menuconfig BSP_USING_UART6 bool "Enable UART6" default n if BSP_USING_UART6 config BSP_UART6_RX_BUFSIZE int "Set UART6 RX buffer size" range 64 65535 depends on BSP_USING_UART6 default 256 config BSP_UART6_TX_BUFSIZE int "Set UART6 TX buffer size" range 0 65535 depends on BSP_USING_UART6 default 0 endif endif menuconfig BSP_USING_LPTIM bool "Enable lptimer" default n select RT_USING_LPTIMER select RT_USING_CLOCK_TIME if BSP_USING_LPTIM config BSP_USING_LPTIM1 bool "Enable LPTIM1" default n config BSP_USING_LPTIM2 bool "Enable LPTIM2" default n config BSP_USING_LPTIM3 bool "Enable LPTIM3" default n endif menuconfig BSP_USING_SPI bool "Enable SPI" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI1 bool "Enable SPI1" default n config BSP_USING_SPI2 bool "Enable SPI2" default n config BSP_USING_SPI3 bool "Enable SPI3" default n config BSP_USING_SPI4 bool "Enable SPI4" default n endif config BSP_USING_QSPI bool "Enable QSPI BUS" select RT_USING_QSPI select RT_USING_SPI default n config BSP_USING_ONCHIP_RTC bool "Enable Onchip RTC" select RT_USING_RTC default n menuconfig BSP_USING_SOFT_I2C bool "Enable software I2C (swi2c)" default n select RT_USING_I2C select RT_USING_SOFT_I2C if BSP_USING_SOFT_I2C menuconfig BSP_USING_SOFT_I2C1 bool "Enable software I2C1 Bus (swi2c1)" default n select RT_USING_SOFT_I2C1 if BSP_USING_SOFT_I2C1 config RT_SOFT_I2C1_SCL_PIN int "swi2c1 SCL pin number" default 22 config RT_SOFT_I2C1_SDA_PIN int "swi2c1 SDA pin number" default 23 endif menuconfig BSP_USING_SOFT_I2C2 bool "Enable software I2C2 Bus (swi2c2)" default n select RT_USING_SOFT_I2C2 if BSP_USING_SOFT_I2C2 config RT_SOFT_I2C2_SCL_PIN int "swi2c2 SCL pin number" default 127 config RT_SOFT_I2C2_SDA_PIN int "swi2c2 SDA pin number" default 125 endif menuconfig BSP_USING_SOFT_I2C3 bool "Enable software I2C3 Bus (swi2c3)" default n select RT_USING_SOFT_I2C3 if BSP_USING_SOFT_I2C3 config RT_SOFT_I2C3_SCL_PIN int "swi2c3 SCL pin number" default 123 config RT_SOFT_I2C3_SDA_PIN int "swi2c3 SDA pin number" default 124 endif endif config BSP_USING_SDRAM bool "Enable SDRAM" select RT_USING_MEMHEAP default n config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n config BSP_USING_LCD bool "Enable LCD" select BSP_USING_LTDC select BSP_USING_GPIO select BSP_USING_SDRAM default n menuconfig BSP_USING_SDIO_ARTPI bool "Enable SDIO" default n select RT_USING_SDIO if BSP_USING_SDIO_ARTPI config BSP_USING_SDIO1 bool "Enable SDIO1" default n config BSP_USING_SDIO2 bool "Enable SDIO2" default n endif config BSP_USING_USBD bool "Enable USB Device" select RT_USING_USB_DEVICE default n menuconfig BSP_USING_USBH bool "Enable USB Host" select RT_USING_USB_HOST default n if BSP_USING_USBH menuconfig RT_USBH_MSTORAGE bool "Enable Udisk Drivers" select RT_USING_DFS select RT_USING_DFS_ELMFAT default n if RT_USBH_MSTORAGE config UDISK_MOUNTPOINT string "Udisk mount dir" default "/" endif endif menuconfig BSP_USING_ETH_H750 bool "Enable Ethernet" default n select RT_USING_LWIP if BSP_USING_ETH_H750 config ETH_RESET_PIN string "ETH RESET PIN" default "PA.3" endif if BSP_USING_ETH_H750 choice ETH_PHY_SEL prompt "Choose ETH PHY" default PHY_USING_LAN8720A config PHY_USING_LAN8720A bool "USING LAN8720A" default n endchoice endif config BSP_USING_LTDC bool default n source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig" endmenu menu "External Libraries" config ART_PI_USING_WIFI_6212_LIB bool "Using Wifi(AP6212) Library" select PKG_USING_EASYFLASH select BSP_USING_SDIO_ARTPI select BSP_USING_SDIO2 select RT_USING_LWIP select RT_USING_WIFI default n endmenu config RT_SOFT_I2C1_HAS_PIN_DEFAULT bool default y if RT_USING_SOFT_I2C1 config RT_SOFT_I2C1_SCL_PIN_DEFAULT int default 22 if RT_USING_SOFT_I2C1 config RT_SOFT_I2C1_SDA_PIN_DEFAULT int default 23 if RT_USING_SOFT_I2C1 endmenu