menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_STM32_UART_V1_TX_TIMEOUT
                int "UART TX timeout"
                default 2000
                depends on RT_USING_SERIAL_V1  
                
            menuconfig BSP_USING_UART1
                bool "Enable UART1"
                default n
                if BSP_USING_UART1
                    config BSP_UART1_RX_USING_DMA
                        bool "Enable UART1 RX DMA"
                        depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART1_TX_USING_DMA
                        bool "Enable UART1 TX DMA"
                        depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART1_RX_BUFSIZE
                        int "Set UART1 RX buffer size"
                        range 64 65535
                        depends on RT_USING_SERIAL_V2
                        default 256

                    config BSP_UART1_TX_BUFSIZE
                        int "Set UART1 TX buffer size"
                        range 0 65535
                        depends on RT_USING_SERIAL_V2
                        default 0

                    config BSP_UART1_DMA_PING_BUFSIZE
                        int "Set UART1 RX DMA ping-pong buffer size"
                        range 32 65535
                        depends on RT_USING_SERIAL_V2 && BSP_UART1_RX_USING_DMA
                        default 64    
                endif

            menuconfig BSP_USING_UART2
                bool "Enable UART2"
                default y
                if BSP_USING_UART2
                    config BSP_UART2_RX_USING_DMA
                        bool "Enable UART2 RX DMA"
                        depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART2_TX_USING_DMA
                        bool "Enable UART2 TX DMA"
                        depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                        default n

                    config BSP_UART2_RX_BUFSIZE
                        int "Set UART2 RX buffer size"
                        range 64 65535
                        depends on RT_USING_SERIAL_V2
                        default 256

                    config BSP_UART2_TX_BUFSIZE
                        int "Set UART2 TX buffer size"
                        range 0 65535
                        depends on RT_USING_SERIAL_V2
                        default 0

                    config BSP_UART2_DMA_PING_BUFSIZE
                        int "Set UART2 RX DMA ping-pong buffer size"
                        range 32 65535
                        depends on RT_USING_SERIAL_V2 && BSP_UART2_RX_USING_DMA
                        default 64                        
                endif
        endif

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n

            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n
        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu