menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"

    config BSP_USING_STLINK_TO_USART
        bool "Enable STLINK TO USART (uart1)"
        select BSP_USING_UART
        select BSP_USING_UART1
        default y

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_STM32_UART_V1_TX_TIMEOUT
                int "UART TX timeout"
                default 2000
                depends on RT_USING_SERIAL_V1
                
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_LPUART1
                bool "Enable LPUART1"
                default n

            config BSP_LPUART1_RX_USING_DMA
                bool "Enable LPUART1 RX DMA"
                depends on BSP_USING_LPUART1 && RT_SERIAL_USING_DMA
                default n

        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n

            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

        endif



    menuconfig BSP_USING_SOFT_I2C
        bool "Enable software I2C (swi2c)"
        default n
        select RT_USING_I2C
        select RT_USING_SOFT_I2C
        if BSP_USING_SOFT_I2C
        menuconfig BSP_USING_SOFT_I2C1
            bool "Enable software I2C1 Bus (swi2c1)"
            default n
            select RT_USING_SOFT_I2C1
            if BSP_USING_SOFT_I2C1
                config RT_SOFT_I2C1_SCL_PIN
                    int "swi2c1 SCL pin number"
                    default 24
                config RT_SOFT_I2C1_SDA_PIN
                    int "swi2c1 SDA pin number"
                    default 25
            endif

        menuconfig BSP_USING_SOFT_I2C3
            bool "Enable software I2C3 Bus (swi2c3)"
            default n
            select RT_USING_SOFT_I2C3
            if BSP_USING_SOFT_I2C3
                config RT_SOFT_I2C3_SCL_PIN
                    int "swi2c3 SCL pin number"
                    default 29
                config RT_SOFT_I2C3_SDA_PIN
                    int "swi2c3 SDA pin number"
                    default 30
            endif
        endif
    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_CLOCK_TIME
        if BSP_USING_TIM

            config BSP_USING_TIM16
                bool "Enable TIM16"
                default n

            config BSP_USING_TIM17
                bool "Enable TIM17"
                default n
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_ONCHIP_RTC
            choice BSP_RTC_LS_SEL
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

    config RT_SOFT_I2C1_HAS_PIN_DEFAULT
        bool
        default y if RT_USING_SOFT_I2C1

    config RT_SOFT_I2C1_SCL_PIN_DEFAULT
        int
        default 24 if RT_USING_SOFT_I2C1

    config RT_SOFT_I2C1_SDA_PIN_DEFAULT
        int
        default 25 if RT_USING_SOFT_I2C1

    config RT_SOFT_I2C3_HAS_PIN_DEFAULT
        bool
        default y if RT_USING_SOFT_I2C3

    config RT_SOFT_I2C3_SCL_PIN_DEFAULT
        int
        default 29 if RT_USING_SOFT_I2C3

    config RT_SOFT_I2C3_SDA_PIN_DEFAULT
        int
        default 30 if RT_USING_SOFT_I2C3

endmenu