threadx.git/ports/cortex_m52/ac6/src, branch master

Normalized the AI disclosure comment to one fixed line per file (#740)

2026-09-15T21:17:26Z

The per-edit disclosure named the product and model, so every agent and every model version appended another line. 74 files carried two to four of them, and the same five products had accumulated 13 spellings -- Copilot against GitHub Copilot, Claude Sonnet 4.6 against claude-sonnet-4.6, four spellings of Codex. Twenty assembly lines carried a doubled comment marker, `; //` or `@ //`. Every file now carries exactly one line, fixed text naming no product: Portions of this file were generated with AI assistance. It is written with the comment character that file already uses, so the `;` and `@` assembly files keep theirs and the doubled markers are gone. Precise attribution stays on the commit, where the Assisted-by trailer is per-change, dated and attached to the diff it describes. A header line cannot hold that record honestly, because the code it names gets rewritten and the line stays. A file-level flag answers whether; the history answers who. Comment-only. 455 files, 455 insertions and 574 deletions: every removed line was a disclosure line, every added line is the fixed text, and no file is left with zero or with more than one. `scripts/check_ports.sh` passes, including the reproducibility check that would catch a ports_arch master and its generated copies drifting apart. Recompiled against dev, every file that builds without a vendor toolchain gives a byte-identical object: 19 of 19 C files under common, 100 of 100 GNU assembly files, and all 16 assemblable files whose comment marker changed. The 10 remaining marker changes are ac5 and IAR sources where `;` already started the comment and only the redundant `//` was removed. Assisted-by: Claude Code (Opus 5)

Removed the vector table offset register and system stack pointer setup from the Cortex-M low-level initialization (#714)

2026-09-09T20:28:59Z

_tx_initialize_low_level wrote VTOR and derived _tx_thread_system_stack_ptr from the reset vector on every Cortex-M port. Programming VTOR is the job of the low-level startup code that runs before the kernel is entered, and doing it again inside ThreadX silently overrode a vector table that the application, a bootloader or a firmware update had already installed. It also forced every application to export a vector table symbol that the kernel itself never needed. _tx_thread_system_stack_ptr is never read by any Cortex-M port, so the value copied out of the reset vector served no purpose. Both blocks are removed from all Cortex-M ports, together with the now-unused symbol declarations. The GreenHills files keep the NVIC base address load that the removed block used to leave in r0 for the SysTick setup that follows. Applications that relied on ThreadX programming VTOR must now set it in their startup code. The bundled examples link their vector table at address zero and run on the reset default. Fixes #370 Assisted-by: Copilot (Opus 5)

Allowed a BASEPRI-masked interrupt to wake the Cortex-M idle loop from WFI (#711)

2026-09-09T15:29:14Z

The idle loop in _tx_thread_schedule masks interrupts before re-reading _tx_thread_execute_ptr, so that an interrupt cannot make a thread ready between that read and the WFI and then be lost. With PRIMASK that is safe: the architecture excludes PRIMASK from the WFI wake-up condition, so the interrupt still wakes the processor and is taken as soon as the loop re-enables interrupts. BASEPRI is not excluded. When TX_PORT_USE_BASEPRI is defined, the mask written at the top of the loop is still in place at the WFI, so any interrupt at or below TX_PORT_BASEPRI fails to wake the processor at all. On a system where every interrupt is managed by ThreadX, that is every interrupt, and the processor stays in WFI or in the low power mode entered by tx_low_power_enter until something outside the mask happens. Set PRIMASK and clear BASEPRI for the duration of the WFI, then restore BASEPRI and clear PRIMASK. Interrupts remain masked across the whole window, so the original race is still closed, but the wake-up condition is now evaluated with BASEPRI clear and any enabled interrupt can end the wait. A pending interrupt is taken at the CPSIE i, or at the existing unmask further down the loop if it falls below TX_PORT_BASEPRI. The change is made in the ARMv7-M and ARMv8-M sources under ports_arch, including the module manager, and propagated to the generated ports with the copy scripts. The ghs and keil ports do not implement TX_PORT_USE_BASEPRI, and Cortex-M0/M0+/M23 have no BASEPRI register, so those ports are unaffected. Verified by assembling every patched GNU port for Cortex-M3, M4, M7, M33, M55 and M85, with and without TX_PORT_USE_BASEPRI, TX_LOW_POWER and TX_ENABLE_EXECUTION_CHANGE_NOTIFY, and by checking the disassembly of the idle loop. Fixes #279 Assisted-by: Copilot (Opus 5)

Added Cortex-M52 (Armv8.1-M) port (#519)

2026-08-16T12:29:46Z

* ports: add Cortex-M52 (Armv8.1-M) port support Add ThreadX port for Cortex-M52, supporting three toolchains: - GNU (GCC) - AC6 (Arm Compiler 6) - IAR Cortex-M52 is an Armv8.1-M Mainline processor sharing the same architecture profile as Cortex-M55 and Cortex-M85. The port is functionally identical to the existing Cortex-M85 port. * ports: update cortex_m52 port copy script,using it update content -Add cortex_m52 in threadx/scriprts/copy_armv8m.sh -Using updated copy_armv8m.sh to generate new cortex_m52 port content * Regenerated the Cortex-M52 port against dev and wired it into the checks The port was generated from ports_arch/ARMv8-M as it stood on master, which has since moved on. Rebasing onto dev and running scripts/copy_armv8_m.sh again brings the twelve stale files into line, which is the point of generating them: the core picks up every ARMv8-M fix made since without anyone porting it by hand. Among what it picks up: "MOV r0, 0" becomes "MOV r0, #0" in the schedule and system-return paths, the non-canonical immediate form that GNU as tolerates and LLVM's assembler rejects; and gnu/src/tx_initialize_low_level.S goes away, since the shared source no longer has it. Two integration points exist only on dev, so the original change could not have included them. cmake/cortex_m52.cmake, so the port can be selected the documented way. Every other Cortex-M core has one. It uses the hard float ABI, as Cortex-M55 and Cortex-M85 do. An entry in scripts/check_clang.sh, likewise with -mfloat-abi=hard. That flag is not decoration: -mcpu=cortex-m52 implies Helium, and building it soft-float ends in "multilib configuration error: No library available for MVE with soft-float ABI" on every file, which reads as a broken port rather than a missing flag. Verified after regenerating: scripts/copy_armv8_m.sh is a no-op, so the tree matches its source; all 14 assembly sources and 188 C sources compile for cortex-m52 with Arm Toolchain for Embedded 22.1.0. Note for anyone building with GNU tools: arm-none-eabi-gcc 13.2.1 rejects -mcpu=cortex-m52 outright. Support arrives in GCC 14. --------- Co-authored-by: Frédéric Desbiens Assisted-by: Claude Code (Opus 5)