tinyusb.git/examples/device, branch etmtrace-rp2350

ci: an empty selection must build nothing, plus selector follow-ups (#3845)

2026-08-25T02:46:42Z

ci: an empty selection must build nothing, plus selector follow-ups A PR whose build axis legitimately selected nothing rebuilt everything. build.yml reads .build.families twice - as a |-joined regex, and implicitly as "is anything selected" - but tested only -z "$FAMILY_REGEX", which an empty list and a charset-rejected one both satisfy while meaning opposite things. ci_set_matrix had already returned the correct all-empty matrix; the fall-open branch discarded it. #3842 and #3840 each spent 74 cmake legs on it. Branch on the two cases instead, rename FAM_* to FAMILY_*, and cover the block with a test that extracts it from build.yml and executes it - it had no test at all, which is how this shipped through two merges. Follow-ups to the same machinery: glob.escape the repo root at five sites, so a checkout path containing [ or * stops failing closed; drop the ci-full label, read after the matrix was already computed and so never functional; delete 13 mcu:MKL25ZXX / mcu:SAME5X skip tokens matching no board; carry the rule table in the module docstring, guarded against drift; and pin six selection behaviours a mutation pass proved untested. Cut the selector's cost 1.8x (26.0s -> 14.6s) with 0 divergences over 260 paths, and stop scoping the membrowse upload by the PR example filter.

examples: document and work around the i.MX RT and LPC55 USB errata

2026-08-18T15:07:49Z

ERR050101: while an isochronous IN endpoint is active, an IN token addressed to that same endpoint number on ANOTHER device sharing the host can silently unprime one of this device's OUT endpoints - control, bulk, interrupt or isochronous alike. NXP states it cannot be detected by software and raises no interrupt, so the endpoint simply stops answering and the transfer never completes. The workaround is a uniqueness requirement rather than a particular number: the isochronous IN endpoint must not share its number with any IN endpoint in use on the bus. One family-wide constant therefore defeats it, since two affected boards on the same hub then pick the same number and each becomes the other's aggressor. CFG_TUSB_MIMXRT1XXX_ERRATA_ERR050101 is set only for the parts whose errata list it - RT1015, RT1020, RT1024 and RT1050, where it is marked no fix scheduled, plus RT1060 and RT1064 rev A - so RT1010 and the RT11xx family keep the ordinary number and cannot collide with an affected board beside them. Several affected boards on one hub can still be given distinct numbers with -DEPNUM_ISO_IN. The guard covers every example that has an isochronous IN endpoint: audio_test, audio_4_channel_mic, uac2_headset, cdc_uac2, usbtest, video_capture and video_capture_2ch. The video examples move the endpoint only when streaming isochronously, since the bulk configuration is unaffected, and video_capture_2ch takes two numbers because it has two streams. The macro name follows CFG_TUSB_RP2_ERRATA_E2/E4/E15 already in tree, and its is fixed, and which cannot be told apart at compile time - a way to define it to 0. device_issues.rst records ERR050101 against every affected part with a link to each errata sheet, and adds the LPC55S2x USB.3 speed-detection and USB.5 isochronous IN entries, neither of which TinyUSB works around. The branch's design notes are included under docs/superpowers. Verified: 340 wedge-free runs on mimxrt1064_evk, which previously wedged within hours, and the macro resolving to endpoint 0x87 on mimxrt1064_evk against 0x83 on mimxrt1010_evk and stm32f407disco.

example(midi2): report device identity in midi2_device

2026-08-14T18:21:24Z

Enable APM32F0 dependency fetching and CI

2026-07-25T03:28:29Z

misc fixes

2026-07-19T12:38:54Z

examples now build

2026-07-19T11:24:40Z

dcd_lpc17_40: address review findings in the iso paths

2026-07-17T17:15:53Z

From a second max-effort review of the branch: - Drop the dead TUSB_XFER_ISOCHRONOUS case in dcd_edpt_open: iso endpoints are armed via dcd_edpt_iso_alloc/activate (TUP_DCD_EDPT_ISO_ALLOC is defined for this IP), never through dcd_edpt_open, so the case and its dd->isochronous assignment were unreachable and asserted a false invariant. Only bulk/interrupt reach the switch now. - Extend the iso compile gate to the classes that actually arm an iso endpoint: DCD_ISO_ENABLED now includes CFG_TUD_BTH (bth_device.c opens an iso voice endpoint). Without it a BTH build would compile the iso machinery out and fail SET_INTERFACE at runtime. - Un-skip LPC175X_6X in the usbtest example: it shares dcd_lpc17_40.c with LPC40XX verbatim, so the "DCD has no isochronous support" skip reason no longer holds. Build-verified for lpcxpresso1769 (previously blocked by the skip). - TU_ATTR_UNUSED on the ep_id_is_iso helper: every caller is under #if DCD_ISO_ENABLED, so non-iso builds don't reference it and clang's -Wunused-function (fatal in CI) rejected the build — gcc stays quiet. Verified with the full lpc17 and lpc40 example sets under arm-clang. A fifth finding — bounding control_ep_read's PACKET_READY spin with a timeout — was implemented and REVERTED: a naive 100k-iteration bound fires on legitimately-slow control reads and intermittently drops the device (hardware-proven by interleaved A/B testing against the pre-fix binary). The infinite wait is retained; the read is only reached once out_received/ out_queued signal data is present, so the theoretical IRQ-off hang is not reachable in practice. Re-verified on ea4088_quickstart: usbtest 30/30 (repeated) + HIL 14/14.

skill: add usb-sniffer — wire-level capture with the ataradov hardware tap

2026-07-17T10:32:47Z

Fourth view in the USB debugging toolset (usbmon = host URBs, usb-debug = host reasoning, usb-target-debug = device firmware, usb-sniffer = what actually crossed D+/D-). Covers the ataradov/usb-sniffer analyzer: headless pcapng capture (--speed ls/fs/hs, --fold, --limit self-exit), Wireshark/tshark analysis recipes, and the wire realities that bite: downstream broadcast, sniffer self-capture noise, xHCI devnum != wire address, tap-point-dependent reset visibility (hub choreography anchors), FS-behind-HS-hub splits. Every recipe hardware-validated on the rig, including the capture-window floor (a 3 s window provably misses the enumeration ladder; 3M packets minimum). Two udev files with distinct audiences, not one: - examples/device/99-tinyusb-examples.rules (renamed from 99-tinyusb.rules): the user-facing rules the examples need — cafe VID access, hidraw, the ModemManager blacklist, a couple of board probes. getting_started.rst, the webusb_serial README and its source comment point here. - tools/88-tinyusb.rules: the HIL rig's private probe/analyzer allowlist, now with the sniffer (6666:6620 + blank FX2LP 04b4:8613). Installed on the rig only; the usb-sniffer skill references it.

dcd_lpc17_40: fix stale EP0 out_received, add isochronous support

2026-07-17T09:48:01Z

EP0 control-OUT fix (usbtest 14/21, errno 110/-74): usbd queues the status-stage OUT ZLP of every control read with buffer=NULL, so the ISR's `if (out_buffer)` check missed it and marked the arriving ZLP as out_received instead. The stale flag poisoned the next control-OUT with data: its first chunk "completed" instantly from an empty EP0 buffer and the host's real DATA NAKed forever. Track queued transfers with an explicit out_queued flag and void half-finished control state on a new SETUP. Isochronous support (UM10562 12.15.6): 5-word DMA descriptors with per-packet size memory, buflen/present_count in packets, one packet per FRAME (no DMARSet/EpIntEn involvement), completion at EOT for both directions. Details that matter: - the iso machinery (5th DD word + packet-size memory) is compiled only when an iso-capable class is enabled (CFG_TUD_AUDIO/VIDEO/VENDOR), so non-iso builds pay nothing: _dcd stays 648 B vs 1032 B with iso - ISR dispatch keys on the hardware's fixed ep-number/type map (ep_id_is_iso), never on dd fields that thread mode rebuilds - iso OUT honors Packet_valid (bit 16) and prefills the hardware writeback slots with 0, so a missed frame counts as 0 bytes instead of reading back stale buffer contents as data - packet count is validated (tu_div_ceil <= ISO_MAX_PACKETS) before the DD is touched, so an oversized transfer is refused without leaving a serviceable half-built descriptor armed for the frame engine - dcd_edpt_iso_alloc and iso_activate both enforce the fixed iso endpoint numbers (3/6/9/12); classes ignore alloc's return value, so activate must not trust it Un-skip LPC40XX in the usbtest example; tier 4 now enumerates and passes iso cases 15/16/22/23. cdc_msc_throughput and printer_to_cdc had bulk on iso-only EP3 (SET_CONFIGURATION failed with -32); add the LPC17/40 EPNUM block (bulk on EP2/EP5) like other fixed-EP examples. Verified on ea4088_quickstart: usbtest tier-4 battery 30/30 repeatedly and the full device HIL suite 14/14 (incl. audio_test iso).

test/hil: usbtest fleet enablement, shuffled scheduling, unique PIDs

2026-07-14T06:22:48Z

Pool/config: - record real uids (ra8m1_ek), enable usbtest for espressif s3/p4, then park ra6m5_ek and ra8m1_ek in boards-skip (ra6m5's usbtest/MSC traffic can kill the uPD720201 host on its ROM firmware; ra8m1 USBHS bring-up pending); max32666/nrf54lm20 stay enabled - their MosChip flakiness never wedges - re-enable device/usbtest on HS boards (mimxrt1064, ch32v307) now that uPD720201 firmware 2.0.2.6 fixes the command-ring death; mimxrt1015 stays skipped - its HS battery killed the controller on both ROM and 2.0.2.6 firmware (board-specific); match the moved host-test bundles (f723 <-> rt1064); skip never-passing tests on the new nrf5340dk/nrf54lm20dk boards and the detached pico host bundle, each documented with a comment Host-controller quirk gating in usbtest.py (auto-skip, self-heals on a healthy xHCI): - MosChip MCS9990 EHCI: case 25 (int-OUT never scheduled, FRINDEX bug) and case 11 (unlinked reads complete short/EREMOTEIO) - Renesas uPD720201 xHCI: firmware-gated. The card must run firmware >= 2.0.2.6 (RAM-uploaded - it reverts to ROM on every power cycle): on older firmware the command ring dies under unlink stress (a Configure Endpoint command stops completing; the hub worker deadlocks holding the device lock; only a host power cycle recovers; three boards reproduced it). usbtest.py reads the FW version register (PCI config 0x6c) and refuses to run at all on older firmware - hil_test surfaces that as a failed test with the reason. On current firmware the full 30-case battery runs (validated FS+HS: metro_m4, f723, f723-DMA all 30/30). Scheduling (hil_test.py): - Shuffle each (board, variant)'s test order with a seeded RNG (HIL_SHUFFLE_SEED to replay) so usbtest batteries and flash churn spread across the timeline instead of convoying on one controller. - Per-controller usbtest + flash semaphores: HIL_USBTEST_PARALLEL (default 4) concurrent usbtest batteries and HIL_FLASH_PARALLEL (default 8) concurrent flashes per host controller. Profiled on uPD720201 firmware 2.0.2.6 across 8/1..12/8: wall time falls 22.2/14.3/12.5/10.8 min at usbtest width 1/2/3/4 and plateaus there; zero controller errors everywhere; first battery case failures (leaf-hub bandwidth stretch) appear at 12/8, and flash width 12 only amplifies flasher-hub contention flakes - so 8/4 is the optimum. A separate battery-window flash throttle was profiled and dropped. - Give every example a unique hardcoded USB PID (0x4001-0x4022, usbtest keeps 0x4010) instead of the PID_MAP interface bitmap: different examples now always re-enumerate back-to-back, even on boards whose CPU reset does not drop D+ (WCH CH58x), so the EXAMPLE_PID table and same-PID adjacency reordering in hil_test.py are gone; only the variant-boundary same-example repeat needs a swap. - Report matrix: stable columns with the metric-bearing tests pinned first (usbtest, cdc_msc_throughput, msc_file_explorer[_freertos]), the rest alphabetical. Fail fast: - enum wait budget 8 s on the first attempt, 4 s on retries; dfu waits are deadline-based so dfu-util's own runtime counts against the budget. A device-absent failure now costs ~3-5x a passing test (20-30 s) instead of 10-30x (47-150 s). - CI runs hil_test with --retry 1 and no in-run second pass: a broken fixture fails the job fast instead of holding the self-hosted runner for hours and blocking other PRs' HIL jobs. hil_test still writes the .skip sidecar, so a manual re-run attempt only retests what failed. Review fixes (multi-agent adversarial review of this commit): - tinyusb_win_usbser.inf: the PID rework moved five CDC examples onto even PIDs the INF's odd-only DeviceList never matched (legacy-Windows usbser binding) - appended 0x4006/4008/400a/4020/4022 to both lists. - usbtest example: USBTEST_TIER is now overridable and the descriptors and pumps are tier-conditional, so a board whose DCD cannot serve a tier lowers it instead of skipping the whole example - RA2A1 (RUSB2 with no isochronous pipe) builds at tier 3 via its BOARD_ define; the host battery follows the tier advertised in bcdDevice. Tier-4 output verified byte-identical after the refactor. - dynamic_configuration's second config derived USB_PID + 11 = 0x4018, colliding with net_lwip_webserver - now USB_PID + 0x0100, outside the per-example space. tools/check_example_pids.py (pre-commit hook) enforces PID uniqueness incl. derived and literal idProduct values. - usbtest.py firmware gate: matched by device ID (uPD720201/720202, both use the 0x6c FW register), and an unreadable version (setpci missing/denied) now refuses with its own message instead of masquerading as "firmware 0x00000000"; noted the gate is necessary but not sufficient (board-specific kills stay per-board skips). - hil_test: deadline waits use time.monotonic(); multiprocessing context pinned to fork (raw semaphores in Pool initargs); flash and usbtest permits unified into one fail-closed, exception-safe ctrl_permit (unknown controller takes every slot and logs a warning instead of silently borrowing slot 0); an all-skipped battery reports as skip, not "0/0" failure; slow-body polls (mtp, printer, disk read) go through a shared deadline-based wait_until so their bodies count against the enum budget; throughput's FS detection compares serials case-insensitively like every other walk; a missing MSC read-speed line now fails the host msc_file_explorer test instead of passing with an empty metric. Hardening: - fail fast (15 s) when a driver-registry sysfs write blocks: a wedged device otherwise turns every subsequent battery into an unkillable D-state writer and silently hangs the whole run - usb-recover skill: a VM reboot is not a reliable cure (MosChip hubs latch up across the PCIe reset); full host power cycle is Co-Authored-By: Claude Fable 5 Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg