tinyusb.git/hw/bsp/stm32f7, branch claude/add-systemview-debug

sysview: per-family RTT buffer defaults, 65536 on RAM-rich parts

2026-09-03T21:21:57Z

The dual-role dogfood measured the 4096 fallback losing 96.7% of ISR exit contexts on mimxrt1064_evk and 99.1% on metro_m4_express; a local-board run measured stm32u575nucleo losing ~19% of the whole stream under a 12 s cdc_msc workload. The default was too small for any real capture on fast parts and every user had to rediscover that per board. Families now declare SYSVIEW_BUFFER_SIZE_DEFAULT in family.cmake (the SYSVIEW_RAM_BASE_DEFAULT pattern): imxrt, nrf, rp2040, samd5x_e5x, stm32f4, stm32f7, stm32h7 and stm32u5 set 65536, the measured-safe value. -DSYSVIEW_BUFFER_SIZE still beats everything; small-RAM parts keep the 4096 fallback and their per-board overrides (stm32f072disco's 2048 verified still honoured). lpc55 measured 34 lost events on the same route, an order of magnitude lighter, so it keeps the fallback rather than inheriting a default on thin evidence.

sysview: FreeRTOS trace hooks, stack high-water and heap tracking

2026-09-03T21:21:57Z

hw/bsp/sysview_freertos_hooks.h maps the FreeRTOS trace macros onto SystemView task records (task names, switches, ready/blocked) and adds heap tracking; the FreeRTOSConfig.h of the families used on the rig include it when SYSVIEW is on. The FreeRTOS examples grow their USB task stacks when CFG_TU*_SYSVIEW is enabled, the same way they already do for CFG_TUSB_DEBUG -- the instrumentation's stack cost is real (measured overflows on lpc55 before the bump).

Fix stm32f723disco host/cdc_msc_hid HIL: UART RX starvation + DWC2 DMA split-IN NAK storm (#3677)

2026-06-11T03:17:28Z

Fix stm32f723disco host HIL: UART RX starvation + DWC2 split bulk NAK/XactErr handling (#3677) stm32f7 BSP — UART RX starvation - The host console USART shared interrupt priority with the USB OTG ISR, so a long OTG interrupt could starve RXNE and drop received bytes. Raise the USART RX IRQ above OTG_FS/OTG_HS in both the bare-metal and FreeRTOS init paths, guarded by #ifdef UART_ID so boards without a UART console keep the default OTG priority. dwc2 host — split NAK/XactErr handling - Slave mode: a persistently-NAKing split bulk/control IN poll re-armed the start-split immediately, storming the ISR and starving task context. Throttle by disabling the channel and re-arming on the resulting halt (no frame deferral). - Buffer-DMA mode: a pure split bulk-OUT NAK was unhandled, leaving the channel halted and stalling the transfer — the dominant cause of CDC echo truncation. Handle it by rewinding the buffer pointers and retrying the start-split (Programming Guide v4.20a 5.1.4.2). - Buffer-DMA mode: a split bulk-OUT XactErr was retried immediately, exhausting HCD_XFER_ERROR_MAX before the transient cleared. Throttle via channel_disable + re-arm to give the hub TT a recovery gap, mirroring slave mode. - All three are scoped to split transfers (hcsplt.split_en); non-split NAK/XactErr keep the core-handled / immediate-retry behavior. The OUT XactErr throttle also excludes periodic split, where channel_disable() is a no-op and would wedge the channel. The nak_disabled flag is generalized to retry_disabled and honors xfer->closing so an endpoint close during a throttled retry tears down cleanly. Verified on stm32f723disco HIL (slave + CFG_TUH_DWC2_DMA_ENABLE): host/cdc_msc_hid, msc_file_explorer, and device_info all pass on both variants; DMA CDC echo went from ~15-25% raw failure to 10/10 clean.

refactor(cmake): comment out unused target folder properties

2026-06-03T14:46:11Z

bsp/stm32f7: fix f746disco jlink device

2026-05-28T22:39:19Z

Signed-off-by: HiFiPhile

ensure board_uart_write return -1 on default

2026-04-29T20:00:05Z

Signed-off-by: HiFiPhile

remove IAR toolchain support from make build system

2026-04-06T04:17:34Z

IAR is only supported with CMake. Remove all IAR-specific references from the Make build system including toolchain files, SRC_S_IAR, LD_FILE_IAR variables, and IAR toolchain detection. Also fix GET_SECTOR_COUNT truncation in msc_file_explorer and broken formatting in stm32f7 board_uart_write. Co-Authored-By: Claude Opus 4.6 (1M context)

update stm32 to use better uart id

2026-04-03T12:38:07Z

stm32 add uart hwfifo if supported, otherwise usb tu_fifo_t for receive uart in irq

2026-04-03T09:33:03Z

add board_uart_read() for f7

2026-03-17T17:20:42Z