Unnamed repository; edit this file 'description' to name the repository. http://cgit.235523.xyz/tinyusb.git/atom/src/portable/dialog?h=0.13.0 2022-01-20T15:28:09Z 2022-01-20T15:28:09Z Jerzy Kasenberg jerzy.kasenberg@codecoup.pl 2022-01-20T08:58:40Z urn:sha1:7b078367e82fae8ef4ec094f6db9e584db82f06a Going to suspend states disable reception on non-0 RX endpoints. Now when USB resume condition is detected, all RX endpoints with pending transfers are resumed. 2022-01-20T09:01:18Z Jerzy Kasenberg jerzy.kasenberg@codecoup.pl 2022-01-20T08:55:25Z urn:sha1:ae4d901d8351437c499cecef349b84af4bb6c239 Bit mask enabling/disabling over-run/unde-run was shifted by one nibble, so interrupt was never enabled. It did not force any issue as this situation could only happen on ISO endpoints without DMA. 2021-10-24T07:39:02Z hathach thach@tinyusb.org 2021-10-24T07:39:02Z urn:sha1:109b7a666155eb1b59bf946be7319ac11bc625ea 2021-10-24T06:11:21Z hathach thach@tinyusb.org 2021-10-24T06:11:21Z urn:sha1:5af989384bd95dbf16f824bcc48e56f3ea283080 2021-10-23T14:23:56Z Ha Thach thach@tinyusb.org 2021-10-23T14:23:56Z urn:sha1:311c05b401591507cbc4977926bcc878d3f119aa 2021-10-17T10:33:14Z hathach thach@tinyusb.org 2021-10-17T10:33:14Z urn:sha1:099d3b377fd619e664e60c948e6f73d7276dd81d since gcc does difference between volatile struct and member when casting pointer 2021-10-15T10:02:15Z Jerzy Kasenberg jerzy.kasenberg@codecoup.pl 2021-10-15T09:57:52Z urn:sha1:bf4b133084585d302691e53faf868c0c37b9eaf0 USB3CV tool verifies MSC device by sending too short or too long packets. In case of too long packets (msc_device requested 31 bytes but incoming data had 32 bytes) extra byte(s) were left in FIFO resulting in some data mismatch later on. Now if more data is received in packet that expected extra bytes are just dropped. 2021-10-15T10:02:15Z Jerzy Kasenberg jerzy.kasenberg@codecoup.pl 2021-10-15T09:34:26Z urn:sha1:49aa0b72a8301f21281fa6498af47ac26bcb1bea Normal TX handler for IN non-0 endpoints is called during outgoing transfer or just after it was finished. It may need to fill TX fifo with same data if TX_DONE is present but ACK_STAT is not. It may need to fill more data when called during transfer. But it may also be called when STALL was sent. In this case TX_DONE is set ACK_STAT is not, just like for packets that were sent but no ACK was received. Code was trying to send something again. There was nothing to send so empty ZLP was scheduled for stalled endpoint. This ZLP was later send to host where valid response was required. This change checks if notification was for STALL endpoint and does not try to fill TX FIFO in that case. 2021-10-13T09:33:54Z Ha Thach thach@tinyusb.org 2021-10-13T09:33:54Z urn:sha1:9da234cd7c73786624970206d7b7b7361275a6b7 da146xx bus reset and sleep reworked 2021-09-24T13:55:16Z Ha Thach thach@tinyusb.org 2021-09-24T13:55:16Z urn:sha1:1c17cb1c451f8564623fef09fa4bd74a0e2a30da dcd_da146xx: Remove registers pointer from xfer_ctl_t