frdmmcxa153 files added

16 files changed, 1480 insertions, 0 deletions

diff --git a/hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h
new file mode 100644
index 000000000..6f10a7ab0
--- /dev/null
+++ b/hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h
@@ -0,0 +1,149 @@
+/*
+ * FreeRTOS Kernel V10.0.0
+ * Copyright (C) 2017 Amazon.com, Inc. or its affiliates.  All Rights Reserved.
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy of
+ * this software and associated documentation files (the "Software"), to deal in
+ * the Software without restriction, including without limitation the rights to
+ * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of
+ * the Software, and to permit persons to whom the Software is furnished to do so,
+ * subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in all
+ * copies or substantial portions of the Software. If you wish to use our Amazon
+ * FreeRTOS name, please do so in a fair use way that does not cause confusion.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS
+ * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR
+ * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER
+ * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
+ * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * http://www.FreeRTOS.org
+ * http://aws.amazon.com/freertos
+ *
+ * 1 tab == 4 spaces!
+ */
+
+
+#ifndef FREERTOS_CONFIG_H
+#define FREERTOS_CONFIG_H
+
+/*-----------------------------------------------------------
+ * Application specific definitions.
+ *
+ * These definitions should be adjusted for your particular hardware and
+ * application requirements.
+ *
+ * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE
+ * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE.
+ *
+ * See http://www.freertos.org/a00110.html.
+ *----------------------------------------------------------*/
+
+// skip if included from IAR assembler
+#ifndef __IASMARM__
+  #include "fsl_device_registers.h"
+#endif
+
+/* Cortex M23/M33 port configuration. */
+#define configENABLE_MPU                        0
+#define configENABLE_FPU                        1
+#define configENABLE_TRUSTZONE                  0
+#define configMINIMAL_SECURE_STACK_SIZE         (1024)
+
+#define configUSE_PREEMPTION                    1
+#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0
+#define configCPU_CLOCK_HZ                      SystemCoreClock
+#define configTICK_RATE_HZ                      ( 1000 )
+#define configMAX_PRIORITIES                    ( 5 )
+#define configMINIMAL_STACK_SIZE                ( 128 )
+#define configTOTAL_HEAP_SIZE                   ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 )
+#define configMAX_TASK_NAME_LEN                 16
+#define configUSE_16_BIT_TICKS                  0
+#define configIDLE_SHOULD_YIELD                 1
+#define configUSE_MUTEXES                       1
+#define configUSE_RECURSIVE_MUTEXES             1
+#define configUSE_COUNTING_SEMAPHORES           1
+#define configQUEUE_REGISTRY_SIZE               4
+#define configUSE_QUEUE_SETS                    0
+#define configUSE_TIME_SLICING                  0
+#define configUSE_NEWLIB_REENTRANT              0
+#define configENABLE_BACKWARD_COMPATIBILITY     1
+#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP   0
+
+#define configSUPPORT_STATIC_ALLOCATION         1
+#define configSUPPORT_DYNAMIC_ALLOCATION        0
+
+/* Hook function related definitions. */
+#define configUSE_IDLE_HOOK                    0
+#define configUSE_TICK_HOOK                    0
+#define configUSE_MALLOC_FAILED_HOOK           0 // cause nested extern warning
+#define configCHECK_FOR_STACK_OVERFLOW         2
+#define configCHECK_HANDLER_INSTALLATION       0
+
+/* Run time and task stats gathering related definitions. */
+#define configGENERATE_RUN_TIME_STATS          0
+#define configRECORD_STACK_HIGH_ADDRESS        1
+#define configUSE_TRACE_FACILITY               1 // legacy trace
+#define configUSE_STATS_FORMATTING_FUNCTIONS   0
+
+/* Co-routine definitions. */
+#define configUSE_CO_ROUTINES                  0
+#define configMAX_CO_ROUTINE_PRIORITIES        2
+
+/* Software timer related definitions. */
+#define configUSE_TIMERS                       1
+#define configTIMER_TASK_PRIORITY              (configMAX_PRIORITIES-2)
+#define configTIMER_QUEUE_LENGTH               32
+#define configTIMER_TASK_STACK_DEPTH           configMINIMAL_STACK_SIZE
+
+/* Optional functions - most linkers will remove unused functions anyway. */
+#define INCLUDE_vTaskPrioritySet               0
+#define INCLUDE_uxTaskPriorityGet              0
+#define INCLUDE_vTaskDelete                    0
+#define INCLUDE_vTaskSuspend                   1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY
+#define INCLUDE_xResumeFromISR                 0
+#define INCLUDE_vTaskDelayUntil                1
+#define INCLUDE_vTaskDelay                     1
+#define INCLUDE_xTaskGetSchedulerState         0
+#define INCLUDE_xTaskGetCurrentTaskHandle      1
+#define INCLUDE_uxTaskGetStackHighWaterMark    0
+#define INCLUDE_xTaskGetIdleTaskHandle         0
+#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0
+#define INCLUDE_pcTaskGetTaskName              0
+#define INCLUDE_eTaskGetState                  0
+#define INCLUDE_xEventGroupSetBitFromISR       0
+#define INCLUDE_xTimerPendFunctionCall         0
+
+/* FreeRTOS hooks to NVIC vectors */
+#define xPortPendSVHandler    PendSV_Handler
+#define xPortSysTickHandler   SysTick_Handler
+#define vPortSVCHandler       SVC_Handler
+
+//--------------------------------------------------------------------+
+// Interrupt nesting behavior configuration.
+//--------------------------------------------------------------------+
+
+// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header
+#define configPRIO_BITS       3
+
+/* The lowest interrupt priority that can be used in a call to a "set priority" function. */
+#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY			  ((1<<configPRIO_BITS) - 1)
+
+/* The highest interrupt priority that can be used by any interrupt service
+routine that makes calls to interrupt safe FreeRTOS API functions.  DO NOT CALL
+INTERRUPT SAFE FREERTOS API FUNCTIONS FROM ANY INTERRUPT THAT HAS A HIGHER
+PRIORITY THAN THIS! (higher priorities are lower numeric values. */
+#define configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY	2
+
+/* Interrupt priorities used by the kernel port layer itself.  These are generic
+to all Cortex-M ports, and do not rely on any particular library functions. */
+#define configKERNEL_INTERRUPT_PRIORITY 		          ( configLIBRARY_LOWEST_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) )
+
+/* !!!! configMAX_SYSCALL_INTERRUPT_PRIORITY must not be set to zero !!!!
+See http://www.FreeRTOS.org/RTOS-Cortex-M3-M4.html. */
+#define configMAX_SYSCALL_INTERRUPT_PRIORITY 	        ( configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY << (8 - configPRIO_BITS) )
+
+#endif
diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/board.cmake b/hw/bsp/mcxa/boards/frdmmcxa153/board.cmake
new file mode 100644
index 000000000..7f3c6c665
--- /dev/null
+++ b/hw/bsp/mcxa/boards/frdmmcxa153/board.cmake
@@ -0,0 +1,18 @@
+set(MCU_VARIANT MCXA153)
+set(MCU_CORE MCXA153)
+
+set(JLINK_DEVICE MCXA153_M33)
+set(PYOCD_TARGET MCXA153)
+set(NXPLINK_DEVICE MCXA153:MCXA153)
+
+function(update_board TARGET)
+  target_compile_definitions(${TARGET} PUBLIC
+    CPU_MCXA153VLH
+    BOARD_TUD_RHPORT=0
+    BOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED
+    )
+  target_sources(${TARGET} PUBLIC
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/clock_config.c
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/pin_mux.c
+    )
+endfunction()
diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/board.h b/hw/bsp/mcxa/boards/frdmmcxa153/board.h
new file mode 100644
index 000000000..d18175c3d
--- /dev/null
+++ b/hw/bsp/mcxa/boards/frdmmcxa153/board.h
@@ -0,0 +1,66 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2021, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+// LED
+#define LED_GPIO              GPIO3
+#define LED_CLK               kCLOCK_GateGPIO3
+#define LED_PIN               12 // red
+#define LED_STATE_ON          0
+
+// WAKE button (Dummy, use unused pin
+#define BUTTON_GPIO           GPIO1
+#define BUTTON_CLK            kCLOCK_GateGPIO1
+#define BUTTON_PIN            7 //sw3
+#define BUTTON_STATE_ACTIVE   0
+
+// UART
+#define UART_DEV              LPUART0
+
+static inline void board_uart_init_clock(void) {
+
+  /* attach 12 MHz clock to LPUART0 (debug console) */
+    CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u);
+    CLOCK_AttachClk(kFRO12M_to_LPUART0);
+
+    RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn);
+}
+
+
+// XTAL
+#define XTAL0_CLK_HZ          (24 * 1000 * 1000U)
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif
diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/board.mk b/hw/bsp/mcxa/boards/frdmmcxa153/board.mk
new file mode 100644
index 000000000..e8797cd95
--- /dev/null
+++ b/hw/bsp/mcxa/boards/frdmmcxa153/board.mk
@@ -0,0 +1,26 @@
+MCU_VARIANT = MCXA153
+MCU_CORE = MCXA153
+PORT = 0
+
+CFLAGS += \
+	-DCPU_MCXA153VLH \
+	-DCPU_MCXA153VLH_cm33_nodsp \
+	-DPRINTF_FLOAT_ENABLE=0 \
+	-DSCANF_FLOAT_ENABLE=0 \
+	-DPRINTF_ADVANCED_ENABLE=0 \
+	-DSCANF_ADVANCED_ENABLE=0 \
+	-mcpu=cortex-m33+nodsp+nofp+nosimd
+
+#FORCING NOT TO USE DPS AND FPU UNITS (THIS CHIP DOESN'T HAVE)
+CFLAGS += -D__SOFTFP__  
+# Undefine __ARM_FEATURE_DSP if it's already defined
+CFLAGS += -U__ARM_FEATURE_DSP
+# Define __ARM_FEATURE_DSP with the new value
+CFLAGS += -D__ARM_FEATURE_DSP=0
+ 
+
+JLINK_DEVICE = MCXA153
+PYOCD_TARGET = MCXA153
+
+# flash using pyocd
+flash: flash-jlink
diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.c b/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.c
new file mode 100644
index 000000000..f16bc51f6
--- /dev/null
+++ b/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.c
@@ -0,0 +1,468 @@
+/*
+ * Copyright 2023 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+/***********************************************************************************************************************
+ * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file
+ * will be overwritten if the respective MCUXpresso Config Tools is used to update this file.
+ **********************************************************************************************************************/
+/*
+ * How to setup clock using clock driver functions:
+ *
+ * 1. Setup clock sources.
+ *
+ * 2. Set up wait states of the flash.
+ *
+ * 3. Set up all dividers.
+ *
+ * 4. Set up all selectors to provide selected clocks.
+ *
+ */
+
+/* clang-format off */
+/* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+!!GlobalInfo
+product: Clocks v12.0
+processor: MCXA153
+package_id: MCXA153VLH
+mcu_data: ksdk2_0
+processor_version: 0.13.0
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
+/* clang-format on */
+
+#include "fsl_clock.h"
+#include "clock_config.h"
+#include "fsl_spc.h"
+
+/*******************************************************************************
+ * Definitions
+ ******************************************************************************/
+
+/*******************************************************************************
+ * Variables
+ ******************************************************************************/
+/* System clock frequency. */
+//uint32_t SystemCoreClock;
+
+/*******************************************************************************
+ ************************ BOARD_InitBootClocks function ************************
+ ******************************************************************************/
+void BOARD_InitBootClocks(void)
+{
+    BOARD_BootClockFRO96M();
+}
+
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO12M **********************
+ ******************************************************************************/
+/* clang-format off */
+/* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+!!Configuration
+name: BOARD_BootClockFRO12M
+outputs:
+- {id: CLK_1M_clock.outFreq, value: 1 MHz}
+- {id: CPU_clock.outFreq, value: 12 MHz}
+- {id: FRO_12M_clock.outFreq, value: 12 MHz}
+- {id: MAIN_clock.outFreq, value: 12 MHz}
+- {id: Slow_clock.outFreq, value: 3 MHz}
+- {id: System_clock.outFreq, value: 12 MHz}
+settings:
+- {id: SCGMode, value: SIRC}
+- {id: FRO_HF_PERIPHERALS_EN_CFG, value: Disabled}
+- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1}
+- {id: SCG.SCSSEL.sel, value: SCG.SIRC}
+- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
+/* clang-format on */
+
+/*******************************************************************************
+ * Variables for BOARD_BootClockFRO12M configuration
+ ******************************************************************************/
+/*******************************************************************************
+ * Code for BOARD_BootClockFRO12M configuration
+ ******************************************************************************/
+void BOARD_BootClockFRO12M(void)
+{
+    uint32_t coreFreq;
+    spc_active_mode_core_ldo_option_t ldoOption;
+    spc_sram_voltage_config_t sramOption;
+
+    /* Get the CPU Core frequency */
+    coreFreq = CLOCK_GetCoreSysClkFreq();
+
+    /* The flow of increasing voltage and frequency */
+    if (coreFreq <= BOARD_BOOTCLOCKFRO12M_CORE_CLOCK) {
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P0V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+    }
+
+    CLOCK_SetupFRO12MClocking();                /*!< Setup FRO12M clock */
+
+    CLOCK_AttachClk(kFRO12M_to_MAIN_CLK);       /* !< Switch MAIN_CLK to FRO12M */
+
+    /* The flow of decreasing voltage and frequency */
+    if (coreFreq > BOARD_BOOTCLOCKFRO12M_CORE_CLOCK) {
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P0V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+    }
+
+    /*!< Set up clock selectors - Attach clocks to the peripheries */
+
+    /*!< Set up dividers */
+    CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U);               /* !< Set AHBCLKDIV divider to value 1 */
+
+    /* Set SystemCoreClock variable */
+    SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK;
+}
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO24M **********************
+ ******************************************************************************/
+/* clang-format off */
+/* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+!!Configuration
+name: BOARD_BootClockFRO24M
+outputs:
+- {id: CLK_1M_clock.outFreq, value: 1 MHz}
+- {id: CLK_48M_clock.outFreq, value: 48 MHz}
+- {id: CPU_clock.outFreq, value: 24 MHz}
+- {id: FRO_12M_clock.outFreq, value: 12 MHz}
+- {id: FRO_HF_DIV_clock.outFreq, value: 48 MHz}
+- {id: FRO_HF_clock.outFreq, value: 48 MHz}
+- {id: MAIN_clock.outFreq, value: 48 MHz}
+- {id: Slow_clock.outFreq, value: 6 MHz}
+- {id: System_clock.outFreq, value: 24 MHz}
+settings:
+- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1}
+- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
+/* clang-format on */
+
+/*******************************************************************************
+ * Variables for BOARD_BootClockFRO24M configuration
+ ******************************************************************************/
+/*******************************************************************************
+ * Code for BOARD_BootClockFRO24M configuration
+ ******************************************************************************/
+void BOARD_BootClockFRO24M(void)
+{
+    uint32_t coreFreq;
+    spc_active_mode_core_ldo_option_t ldoOption;
+    spc_sram_voltage_config_t sramOption;
+
+    /* Get the CPU Core frequency */
+    coreFreq = CLOCK_GetCoreSysClkFreq();
+
+    /* The flow of increasing voltage and frequency */
+    if (coreFreq <= BOARD_BOOTCLOCKFRO24M_CORE_CLOCK) {
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P0V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+    }
+
+    CLOCK_SetupFROHFClocking(48000000U);               /*!< Enable FRO HF(48MHz) output */
+
+    CLOCK_SetupFRO12MClocking();                /*!< Setup FRO12M clock */
+
+    CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK);       /* !< Switch MAIN_CLK to FRO_HF */
+
+    /* The flow of decreasing voltage and frequency */
+    if (coreFreq > BOARD_BOOTCLOCKFRO24M_CORE_CLOCK) {
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P0V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+    }
+
+    /*!< Set up clock selectors - Attach clocks to the peripheries */
+
+    /*!< Set up dividers */
+    CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 2U);               /* !< Set AHBCLKDIV divider to value 2 */
+    CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U);           /* !< Set FROHFDIV divider to value 1 */
+
+    /* Set SystemCoreClock variable */
+    SystemCoreClock = BOARD_BOOTCLOCKFRO24M_CORE_CLOCK;
+}
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO48M **********************
+ ******************************************************************************/
+/* clang-format off */
+/* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+!!Configuration
+name: BOARD_BootClockFRO48M
+outputs:
+- {id: CLK_1M_clock.outFreq, value: 1 MHz}
+- {id: CLK_48M_clock.outFreq, value: 48 MHz}
+- {id: CPU_clock.outFreq, value: 48 MHz}
+- {id: FRO_12M_clock.outFreq, value: 12 MHz}
+- {id: FRO_HF_DIV_clock.outFreq, value: 48 MHz}
+- {id: FRO_HF_clock.outFreq, value: 48 MHz}
+- {id: MAIN_clock.outFreq, value: 48 MHz}
+- {id: Slow_clock.outFreq, value: 12 MHz}
+- {id: System_clock.outFreq, value: 48 MHz}
+settings:
+- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
+/* clang-format on */
+
+/*******************************************************************************
+ * Variables for BOARD_BootClockFRO48M configuration
+ ******************************************************************************/
+/*******************************************************************************
+ * Code for BOARD_BootClockFRO48M configuration
+ ******************************************************************************/
+void BOARD_BootClockFRO48M(void)
+{
+    uint32_t coreFreq;
+    spc_active_mode_core_ldo_option_t ldoOption;
+    spc_sram_voltage_config_t sramOption;
+
+    /* Get the CPU Core frequency */
+    coreFreq = CLOCK_GetCoreSysClkFreq();
+
+    /* The flow of increasing voltage and frequency */
+    if (coreFreq <= BOARD_BOOTCLOCKFRO48M_CORE_CLOCK) {
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P0V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+    }
+
+    CLOCK_SetupFROHFClocking(48000000U);               /*!< Enable FRO HF(48MHz) output */
+
+    CLOCK_SetupFRO12MClocking();                /*!< Setup FRO12M clock */
+
+    CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK);       /* !< Switch MAIN_CLK to FRO_HF */
+
+    /* The flow of decreasing voltage and frequency */
+    if (coreFreq > BOARD_BOOTCLOCKFRO48M_CORE_CLOCK) {
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P0V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+    }
+
+    /*!< Set up clock selectors - Attach clocks to the peripheries */
+
+    /*!< Set up dividers */
+    CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U);               /* !< Set AHBCLKDIV divider to value 1 */
+    CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U);           /* !< Set FROHFDIV divider to value 1 */
+
+    /* Set SystemCoreClock variable */
+    SystemCoreClock = BOARD_BOOTCLOCKFRO48M_CORE_CLOCK;
+}
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO64M **********************
+ ******************************************************************************/
+/* clang-format off */
+/* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+!!Configuration
+name: BOARD_BootClockFRO64M
+outputs:
+- {id: CLK_1M_clock.outFreq, value: 1 MHz}
+- {id: CLK_48M_clock.outFreq, value: 48 MHz}
+- {id: CPU_clock.outFreq, value: 64 MHz}
+- {id: FRO_12M_clock.outFreq, value: 12 MHz}
+- {id: FRO_HF_DIV_clock.outFreq, value: 64 MHz}
+- {id: FRO_HF_clock.outFreq, value: 64 MHz}
+- {id: MAIN_clock.outFreq, value: 64 MHz}
+- {id: Slow_clock.outFreq, value: 16 MHz}
+- {id: System_clock.outFreq, value: 64 MHz}
+settings:
+- {id: VDD_CORE, value: voltage_1v1}
+- {id: MRCC.FROHFDIV.scale, value: '1', locked: true}
+- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1}
+- {id: SYSCON.AHBCLKDIV.scale, value: '1', locked: true}
+sources:
+- {id: SCG.FIRC.outFreq, value: 64 MHz}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
+/* clang-format on */
+
+/*******************************************************************************
+ * Variables for BOARD_BootClockFRO64M configuration
+ ******************************************************************************/
+/*******************************************************************************
+ * Code for BOARD_BootClockFRO64M configuration
+ ******************************************************************************/
+void BOARD_BootClockFRO64M(void)
+{
+    uint32_t coreFreq;
+    spc_active_mode_core_ldo_option_t ldoOption;
+    spc_sram_voltage_config_t sramOption;
+
+    /* Get the CPU Core frequency */
+    coreFreq = CLOCK_GetCoreSysClkFreq();
+
+    /* The flow of increasing voltage and frequency */
+    if (coreFreq <= BOARD_BOOTCLOCKFRO64M_CORE_CLOCK) {
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P1V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+    }
+
+    CLOCK_SetupFROHFClocking(64000000U);               /*!< Enable FRO HF(64MHz) output */
+
+    CLOCK_SetupFRO12MClocking();                /*!< Setup FRO12M clock */
+
+    CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK);       /* !< Switch MAIN_CLK to FRO_HF */
+
+    /* The flow of decreasing voltage and frequency */
+    if (coreFreq > BOARD_BOOTCLOCKFRO64M_CORE_CLOCK) {
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P1V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+    }
+
+    /*!< Set up clock selectors - Attach clocks to the peripheries */
+
+    /*!< Set up dividers */
+    CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U);               /* !< Set AHBCLKDIV divider to value 1 */
+    CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U);           /* !< Set FROHFDIV divider to value 1 */
+
+    /* Set SystemCoreClock variable */
+    SystemCoreClock = BOARD_BOOTCLOCKFRO64M_CORE_CLOCK;
+}
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO96M **********************
+ ******************************************************************************/
+/* clang-format off */
+/* TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+!!Configuration
+name: BOARD_BootClockFRO96M
+called_from_default_init: true
+outputs:
+- {id: CLK_1M_clock.outFreq, value: 1 MHz}
+- {id: CLK_48M_clock.outFreq, value: 48 MHz}
+- {id: CPU_clock.outFreq, value: 96 MHz}
+- {id: FRO_12M_clock.outFreq, value: 12 MHz}
+- {id: FRO_HF_DIV_clock.outFreq, value: 96 MHz}
+- {id: FRO_HF_clock.outFreq, value: 96 MHz}
+- {id: MAIN_clock.outFreq, value: 96 MHz}
+- {id: Slow_clock.outFreq, value: 24 MHz}
+- {id: System_clock.outFreq, value: 96 MHz}
+settings:
+- {id: VDD_CORE, value: voltage_1v1}
+- {id: CLKOUTDIV_HALT, value: Enable}
+- {id: MRCC.FROHFDIV.scale, value: '1', locked: true}
+- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1}
+- {id: SYSCON.AHBCLKDIV.scale, value: '1', locked: true}
+sources:
+- {id: SCG.FIRC.outFreq, value: 96 MHz}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/
+/* clang-format on */
+
+/*******************************************************************************
+ * Variables for BOARD_BootClockFRO96M configuration
+ ******************************************************************************/
+/*******************************************************************************
+ * Code for BOARD_BootClockFRO96M configuration
+ ******************************************************************************/
+void BOARD_BootClockFRO96M(void)
+{
+    uint32_t coreFreq;
+    spc_active_mode_core_ldo_option_t ldoOption;
+    spc_sram_voltage_config_t sramOption;
+
+    /* Get the CPU Core frequency */
+    coreFreq = CLOCK_GetCoreSysClkFreq();
+
+    /* The flow of increasing voltage and frequency */
+    if (coreFreq <= BOARD_BOOTCLOCKFRO96M_CORE_CLOCK) {
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x2U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P1V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+    }
+
+    CLOCK_SetupFROHFClocking(96000000U);               /*!< Enable FRO HF(96MHz) output */
+
+    CLOCK_SetupFRO12MClocking();                /*!< Setup FRO12M clock */
+
+    CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK);       /* !< Switch MAIN_CLK to FRO_HF */
+
+    /* The flow of decreasing voltage and frequency */
+    if (coreFreq > BOARD_BOOTCLOCKFRO96M_CORE_CLOCK) {
+        /* Configure Flash to support different voltage level and frequency */
+        FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x2U));
+        /* Specifies the operating voltage for the SRAM's read/write timing margin */
+        sramOption.operateVoltage = kSPC_sramOperateAt1P1V;
+        sramOption.requestVoltageUpdate =  true;
+        (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption);
+        /* Set the LDO_CORE VDD regulator level */
+        ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage;
+        ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength;
+        (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption);
+    }
+
+    /*!< Set up clock selectors - Attach clocks to the peripheries */
+
+    /*!< Set up dividers */
+    CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U);               /* !< Set AHBCLKDIV divider to value 1 */
+    CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U);           /* !< Set FROHFDIV divider to value 1 */
+
+    /* Set SystemCoreClock variable */
+    SystemCoreClock = BOARD_BOOTCLOCKFRO96M_CORE_CLOCK;
+}
diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h b/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h
new file mode 100644
index 000000000..079d0d312
--- /dev/null
+++ b/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h
@@ -0,0 +1,170 @@
+/*
+ * Copyright 2023 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+ 
+/***********************************************************************************************************************
+ * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file
+ * will be overwritten if the respective MCUXpresso Config Tools is used to update this file.
+ **********************************************************************************************************************/
+
+#ifndef _CLOCK_CONFIG_H_
+#define _CLOCK_CONFIG_H_
+
+#include "fsl_common.h"
+
+/*******************************************************************************
+ * Definitions
+ ******************************************************************************/
+
+/*******************************************************************************
+ ************************ BOARD_InitBootClocks function ************************
+ ******************************************************************************/
+
+#if defined(__cplusplus)
+extern "C" {
+#endif /* __cplusplus*/
+
+/*!
+ * @brief This function executes default configuration of clocks.
+ *
+ */
+void BOARD_InitBootClocks(void);
+
+#if defined(__cplusplus)
+}
+#endif /* __cplusplus*/
+
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO12M **********************
+ ******************************************************************************/
+/*******************************************************************************
+ * Definitions for BOARD_BootClockFRO12M configuration
+ ******************************************************************************/
+#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK           12000000U  /*!< Core clock frequency: 12000000Hz */
+
+
+/*******************************************************************************
+ * API for BOARD_BootClockFRO12M configuration
+ ******************************************************************************/
+#if defined(__cplusplus)
+extern "C" {
+#endif /* __cplusplus*/
+
+/*!
+ * @brief This function executes configuration of clocks.
+ *
+ */
+void BOARD_BootClockFRO12M(void);
+
+#if defined(__cplusplus)
+}
+#endif /* __cplusplus*/
+
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO24M **********************
+ ******************************************************************************/
+/*******************************************************************************
+ * Definitions for BOARD_BootClockFRO24M configuration
+ ******************************************************************************/
+#define BOARD_BOOTCLOCKFRO24M_CORE_CLOCK           24000000U  /*!< Core clock frequency: 24000000Hz */
+
+
+/*******************************************************************************
+ * API for BOARD_BootClockFRO24M configuration
+ ******************************************************************************/
+#if defined(__cplusplus)
+extern "C" {
+#endif /* __cplusplus*/
+
+/*!
+ * @brief This function executes configuration of clocks.
+ *
+ */
+void BOARD_BootClockFRO24M(void);
+
+#if defined(__cplusplus)
+}
+#endif /* __cplusplus*/
+
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO48M **********************
+ ******************************************************************************/
+/*******************************************************************************
+ * Definitions for BOARD_BootClockFRO48M configuration
+ ******************************************************************************/
+#define BOARD_BOOTCLOCKFRO48M_CORE_CLOCK           48000000U  /*!< Core clock frequency: 48000000Hz */
+
+
+/*******************************************************************************
+ * API for BOARD_BootClockFRO48M configuration
+ ******************************************************************************/
+#if defined(__cplusplus)
+extern "C" {
+#endif /* __cplusplus*/
+
+/*!
+ * @brief This function executes configuration of clocks.
+ *
+ */
+void BOARD_BootClockFRO48M(void);
+
+#if defined(__cplusplus)
+}
+#endif /* __cplusplus*/
+
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO64M **********************
+ ******************************************************************************/
+/*******************************************************************************
+ * Definitions for BOARD_BootClockFRO64M configuration
+ ******************************************************************************/
+#define BOARD_BOOTCLOCKFRO64M_CORE_CLOCK           64000000U  /*!< Core clock frequency: 64000000Hz */
+
+
+/*******************************************************************************
+ * API for BOARD_BootClockFRO64M configuration
+ ******************************************************************************/
+#if defined(__cplusplus)
+extern "C" {
+#endif /* __cplusplus*/
+
+/*!
+ * @brief This function executes configuration of clocks.
+ *
+ */
+void BOARD_BootClockFRO64M(void);
+
+#if defined(__cplusplus)
+}
+#endif /* __cplusplus*/
+
+/*******************************************************************************
+ ******************** Configuration BOARD_BootClockFRO96M **********************
+ ******************************************************************************/
+/*******************************************************************************
+ * Definitions for BOARD_BootClockFRO96M configuration
+ ******************************************************************************/
+#define BOARD_BOOTCLOCKFRO96M_CORE_CLOCK           96000000U  /*!< Core clock frequency: 96000000Hz */
+
+
+/*******************************************************************************
+ * API for BOARD_BootClockFRO96M configuration
+ ******************************************************************************/
+#if defined(__cplusplus)
+extern "C" {
+#endif /* __cplusplus*/
+
+/*!
+ * @brief This function executes configuration of clocks.
+ *
+ */
+void BOARD_BootClockFRO96M(void);
+
+#if defined(__cplusplus)
+}
+#endif /* __cplusplus*/
+
+#endif /* _CLOCK_CONFIG_H_ */
diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c
new file mode 100644
index 000000000..b0e6de560
--- /dev/null
+++ b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c
@@ -0,0 +1,159 @@
+/*
+ * Copyright 2023 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+ 
+/***********************************************************************************************************************
+ * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file
+ * will be overwritten if the respective MCUXpresso Config Tools is used to update this file.
+ **********************************************************************************************************************/
+
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+!!GlobalInfo
+product: Pins v14.0
+processor: MCXA153
+package_id: MCXA153VLH
+mcu_data: ksdk2_0
+processor_version: 0.14.3
+pin_labels:
+- {pin_num: '38', pin_signal: P3_12/LPUART2_RTS_B/CT1_MAT2/PWM0_X0, label: LED_RED, identifier: LED_RED}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+
+#include "fsl_common.h"
+#include "fsl_port.h"
+#include "fsl_gpio.h"
+#include "pin_mux.h"
+
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitBootPins
+ * Description   : Calls initialization functions.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitBootPins(void)
+{
+    BOARD_InitPins();
+}
+
+/* clang-format off */
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitPins:
+- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'}
+- pin_list:
+  - {pin_num: '38', peripheral: GPIO3, signal: 'GPIO, 12', pin_signal: P3_12/LPUART2_RTS_B/CT1_MAT2/PWM0_X0, direction: OUTPUT, gpio_init_state: 'false', slew_rate: fast,
+    open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+/* clang-format on */
+
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitPins
+ * Description   : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitPins(void)
+{
+    RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn);
+    RESET_PeripheralReset(kPORT0_RST_SHIFT_RSTn);
+    CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u);
+    CLOCK_AttachClk(kFRO12M_to_LPUART0);
+
+    /* write to PORT0: Peripheral clock is enabled */
+    CLOCK_EnableClock(kCLOCK_GatePORT0);
+
+    /* Write to GPIO3: Peripheral clock is enabled */
+    CLOCK_EnableClock(kCLOCK_GateGPIO3);
+    /* Write to PORT3: Peripheral clock is enabled */
+    CLOCK_EnableClock(kCLOCK_GatePORT3);
+    /* GPIO3 peripheral is released from reset */
+    RESET_ReleasePeripheralReset(kGPIO3_RST_SHIFT_RSTn);
+    /* PORT3 peripheral is released from reset */
+    RESET_ReleasePeripheralReset(kPORT3_RST_SHIFT_RSTn);
+
+    const port_pin_config_t port3_12_pin38_config = {/* Internal pull-up/down resistor is disabled */
+                                       kPORT_PullDisable,
+                                       /* Low internal pull resistor value is selected. */
+                                       kPORT_LowPullResistor,
+                                       /* Fast slew rate is configured */
+                                       kPORT_FastSlewRate,
+                                       /* Passive input filter is disabled */
+                                       kPORT_PassiveFilterDisable,
+                                       /* Open drain output is disabled */
+                                       kPORT_OpenDrainDisable,
+                                       /* Low drive strength is configured */
+                                       kPORT_LowDriveStrength,
+                                       /* Normal drive strength is configured */
+                                       kPORT_NormalDriveStrength,
+                                       /* Pin is configured as P3_12 */
+                                       kPORT_MuxAlt0,
+                                       /* Digital input enabled */
+                                       kPORT_InputBufferEnable,
+                                       /* Digital input is not inverted */
+                                       kPORT_InputNormal,
+                                       /* Pin Control Register fields [15:0] are not locked */
+                                       kPORT_UnlockRegister};
+    /* PORT3_12 (pin 38) is configured as P3_12 */
+      PORT_SetPinConfig(PORT3, 12U, &port3_12_pin38_config);
+
+    const port_pin_config_t port0_2_pin51_config = {/* Internal pull-up resistor is enabled */
+                                                    kPORT_PullUp,
+                                                    /* Low internal pull resistor value is selected. */
+                                                    kPORT_LowPullResistor,
+                                                    /* Fast slew rate is configured */
+                                                    kPORT_FastSlewRate,
+                                                    /* Passive input filter is disabled */
+                                                    kPORT_PassiveFilterDisable,
+                                                    /* Open drain output is disabled */
+                                                    kPORT_OpenDrainDisable,
+                                                    /* Low drive strength is configured */
+                                                    kPORT_LowDriveStrength,
+                                                    /* Normal drive strength is configured */
+                                                    kPORT_NormalDriveStrength,
+                                                    /* Pin is configured as LPUART0_RXD */
+                                                    kPORT_MuxAlt2,
+                                                    /* Digital input enabled */
+                                                    kPORT_InputBufferEnable,
+                                                    /* Digital input is not inverted */
+                                                    kPORT_InputNormal,
+                                                    /* Pin Control Register fields [15:0] are not locked */
+                                                    kPORT_UnlockRegister};
+    /* PORT0_2 (pin 51) is configured as LPUART0_RXD */
+    PORT_SetPinConfig(PORT0, 2U, &port0_2_pin51_config);
+
+    const port_pin_config_t port0_3_pin52_config = {/* Internal pull-up resistor is enabled */
+                                                    kPORT_PullUp,
+                                                    /* Low internal pull resistor value is selected. */
+                                                    kPORT_LowPullResistor,
+                                                    /* Fast slew rate is configured */
+                                                    kPORT_FastSlewRate,
+                                                    /* Passive input filter is disabled */
+                                                    kPORT_PassiveFilterDisable,
+                                                    /* Open drain output is disabled */
+                                                    kPORT_OpenDrainDisable,
+                                                    /* Low drive strength is configured */
+                                                    kPORT_LowDriveStrength,
+                                                    /* Normal drive strength is configured */
+                                                    kPORT_NormalDriveStrength,
+                                                    /* Pin is configured as LPUART0_TXD */
+                                                    kPORT_MuxAlt2,
+                                                    /* Digital input enabled */
+                                                    kPORT_InputBufferEnable,
+                                                    /* Digital input is not inverted */
+                                                    kPORT_InputNormal,
+                                                    /* Pin Control Register fields [15:0] are not locked */
+                                                    kPORT_UnlockRegister};
+    /* PORT0_3 (pin 52) is configured as LPUART0_TXD */
+    PORT_SetPinConfig(PORT0, 3U, &port0_3_pin52_config);
+
+}
+/***********************************************************************************************************************
+ * EOF
+ **********************************************************************************************************************/
diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h
new file mode 100644
index 000000000..06b6fdee9
--- /dev/null
+++ b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h
@@ -0,0 +1,47 @@
+/*
+ * Copyright 2022 NXP
+ * All rights reserved.
+ *
+ * SPDX-License-Identifier: BSD-3-Clause
+ */
+
+#ifndef _PIN_MUX_H_
+#define _PIN_MUX_H_
+
+/*!
+ * @addtogroup pin_mux
+ * @{
+ */
+
+/***********************************************************************************************************************
+ * API
+ **********************************************************************************************************************/
+
+#if defined(__cplusplus)
+extern "C" {
+#endif
+
+/*!
+ * @brief Calls initialization functions.
+ *
+ */
+void BOARD_InitBootPins(void);
+
+/*!
+ * @brief Configures pin routing and optionally pin electrical features.
+ *
+ */
+void BOARD_InitPins(void);
+
+#if defined(__cplusplus)
+}
+#endif
+
+/*!
+ * @}
+ */
+#endif /* _PIN_MUX_H_ */
+
+/***********************************************************************************************************************
+ * EOF
+ **********************************************************************************************************************/
diff --git a/hw/bsp/mcxa/debug.jlinkscript b/hw/bsp/mcxa/debug.jlinkscript
new file mode 100644
index 000000000..fd8bcffef
--- /dev/null
+++ b/hw/bsp/mcxa/debug.jlinkscript
@@ -0,0 +1,5 @@
+int SetupTarget(void) {
+  JLINK_ExecCommand("SetRTTSearchRanges 0x20000000 0x40000");
+
+  return 0;
+}
diff --git a/hw/bsp/mcxa/family.c b/hw/bsp/mcxa/family.c
new file mode 100644
index 000000000..97abc1bc3
--- /dev/null
+++ b/hw/bsp/mcxa/family.c
@@ -0,0 +1,163 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2018, hathach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#include "bsp/board_api.h"
+#include "fsl_device_registers.h"
+#include "fsl_gpio.h"
+#include "fsl_lpuart.h"
+#include "board.h"
+
+#include "pin_mux.h"
+#include "clock_config.h"
+#include "fsl_common.h"
+
+
+#ifdef BOARD_TUD_RHPORT
+  #define PORT_SUPPORT_DEVICE(_n)  (BOARD_TUD_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_DEVICE(_n)  0
+#endif
+
+#ifdef BOARD_TUH_RHPORT
+  #define PORT_SUPPORT_HOST(_n)    (BOARD_TUH_RHPORT == _n)
+#else
+  #define PORT_SUPPORT_HOST(_n)    0
+#endif
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM
+//--------------------------------------------------------------------+
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USB0_FS_IRQHandler(void)
+{
+  tud_int_handler(0);
+}
+
+void board_init(void)
+{
+  BOARD_InitPins();
+  BOARD_InitBootClocks();
+  CLOCK_SetupExtClocking(XTAL0_CLK_HZ);
+
+  // 1ms tick timer
+  SysTick_Config(SystemCoreClock / 1000);
+
+  // LED
+  CLOCK_EnableClock(LED_CLK);
+  gpio_pin_config_t LED_RED_config = {
+      .pinDirection = kGPIO_DigitalOutput,
+      .outputLogic = 0U
+  };
+  
+  /* Initialize GPIO functionality on pin PIO3_12 (pin 38)  */
+  GPIO_PinInit(LED_GPIO, LED_PIN, &LED_RED_config);
+  board_led_write(1);
+
+  // Button
+#ifdef BUTTON_GPIO
+  CLOCK_EnableClock(BUTTON_CLK);
+  gpio_pin_config_t const button_config = { kGPIO_DigitalInput, 0};
+  GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config);
+#endif
+
+#ifdef UART_DEV
+
+  CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u);
+  CLOCK_AttachClk(kFRO12M_to_LPUART0);
+  RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn);
+
+  lpuart_config_t uart_config;
+  LPUART_GetDefaultConfig(&uart_config);
+  uart_config.baudRate_Bps = 115200;
+  uart_config.enableTx     = true;
+  uart_config.enableRx     = true; 
+  LPUART_Init(UART_DEV, &uart_config, 12000000u);
+
+
+#endif
+
+  // USB VBUS
+  /* PORT0 PIN22 configured as USB0_VBUS */
+
+#if PORT_SUPPORT_DEVICE(0)
+  // Port0 is Full Speed
+
+  RESET_PeripheralReset(kUSB0_RST_SHIFT_RSTn);
+  CLOCK_EnableUsbfsClock();
+#endif
+
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state)
+{
+  GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON));
+}
+
+uint32_t board_button_read(void)
+{
+#ifdef BUTTON_GPIO
+  return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN);
+#else
+  return 1;
+#endif
+}
+
+int board_uart_read(uint8_t* buf, int len)
+{
+  (void) buf; (void) len;
+  return 0;
+}
+
+int board_uart_write(void const * buf, int len)
+{
+#ifdef UART_DEV
+  LPUART_WriteBlocking(UART_DEV, (uint8_t const *) buf, len);
+  return len;
+#else
+  (void) buf; (void) len;
+  return 0;
+#endif
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler(void)
+{
+  system_ticks++;
+}
+
+uint32_t board_millis(void)
+{
+  return system_ticks;
+}
+#endif
diff --git a/hw/bsp/mcxa/family.cmake b/hw/bsp/mcxa/family.cmake
new file mode 100644
index 000000000..0aa690afc
--- /dev/null
+++ b/hw/bsp/mcxa/family.cmake
@@ -0,0 +1,110 @@
+include_guard()
+
+if (NOT BOARD)
+  message(FATAL_ERROR "BOARD not specified")
+endif ()
+
+set(SDK_DIR ${TOP}/hw/mcu/nxp/mcux-sdk)
+set(CMSIS_DIR ${TOP}/lib/CMSIS_5)
+
+# include board specific
+include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake)
+
+# toolchain set up
+set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor")
+set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOLCHAIN}.cmake)
+
+set(FAMILY_MCUS MCXA CACHE INTERNAL "")
+
+
+#------------------------------------
+# BOARD_TARGET
+#------------------------------------
+# only need to be built ONCE for all examples
+function(add_board_target BOARD_TARGET)
+  if (NOT TARGET ${BOARD_TARGET})
+    add_library(${BOARD_TARGET} STATIC
+      # external driver
+      #lib/sct_neopixel/sct_neopixel.c
+
+      # driver
+      ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_gpio.c
+      ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_common_arm.c
+      ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpuart.c
+      ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpflexcomm.c
+      # mcu
+      ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c
+      ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_reset.c
+      ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_CORE}.c
+      )
+    #  target_compile_definitions(${BOARD_TARGET} PUBLIC
+    #    )
+    target_include_directories(${BOARD_TARGET} PUBLIC
+      # driver
+      # mcu
+      ${CMSIS_DIR}/CMSIS/Core/Include
+      ${SDK_DIR}/devices/${MCU_VARIANT}
+      ${SDK_DIR}/devices/${MCU_VARIANT}/drivers
+      )
+
+    update_board(${BOARD_TARGET})
+
+    if (CMAKE_C_COMPILER_ID STREQUAL "GNU")
+      target_sources(${BOARD_TARGET} PUBLIC
+        ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_CORE}.S
+        )
+      target_link_options(${BOARD_TARGET} PUBLIC
+        # linker file
+        "LINKER:--script=${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_CORE}_flash.ld"
+        # nanolib
+        --specs=nosys.specs
+        --specs=nano.specs
+        )
+    elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR")
+      target_link_options(${BOARD_TARGET} PUBLIC
+        "LINKER:--config=${LD_FILE_IAR}"
+        )
+    endif ()
+  endif ()
+endfunction()
+
+
+#------------------------------------
+# Functions
+#------------------------------------
+function(family_configure_example TARGET RTOS)
+  family_configure_common(${TARGET} ${RTOS})
+
+  # Board target
+  add_board_target(board_${BOARD})
+
+  #---------- Port Specific ----------
+  # These files are built for each example since it depends on example's tusb_config.h
+  target_sources(${TARGET} PUBLIC
+    # BSP
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c
+    )
+  target_include_directories(${TARGET} PUBLIC
+    # family, hw, board
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../
+    ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD}
+    )
+
+  # Add TinyUSB target and port source
+  family_add_tinyusb(${TARGET} OPT_MCU_MCXA ${RTOS})
+  target_sources(${TARGET}-tinyusb PUBLIC
+    # TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS
+    ${TOP}/src/portable/chipidea/ci_fs/dcd_ci_fs.c
+    )
+  target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD})  
+
+  # Link dependencies
+  target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb)
+
+  # Flashing
+  family_flash_jlink(${TARGET})
+  #family_flash_nxplink(${TARGET})
+  #family_flash_pyocd(${TARGET})
+endfunction()
diff --git a/hw/bsp/mcxa/family.mk b/hw/bsp/mcxa/family.mk
new file mode 100644
index 000000000..b32282d04
--- /dev/null
+++ b/hw/bsp/mcxa/family.mk
@@ -0,0 +1,42 @@
+UF2_FAMILY_ID = 0x2abc77ec
+SDK_DIR = hw/mcu/nxp/mcux-sdk
+
+DEPS_SUBMODULES += $(SDK_DIR) lib/CMSIS_5		#not found
+
+include $(TOP)/$(BOARD_PATH)/board.mk
+CPU_CORE ?= cortex-m33
+
+CFLAGS += \
+  -flto \
+  -DCFG_TUSB_MCU=OPT_MCU_MCXA \
+  -DBOARD_TUD_RHPORT=0 
+
+# mcu driver cause following warnings
+CFLAGS += -Wno-error=unused-parameter -Wno-error=old-style-declaration
+
+LDFLAGS_GCC += -specs=nosys.specs -specs=nano.specs
+
+# All source paths should be relative to the top level.
+LD_FILE ?= $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/$(MCU_CORE)_flash.ld
+
+# TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS
+$(info "PORT0 Full Speed")
+CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED
+SRC_C += src/portable/chipidea/ci_fs/dcd_ci_fs.c
+
+SRC_C += \
+	$(SDK_DIR)/devices/$(MCU_VARIANT)/system_$(MCU_CORE).c \
+	$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_clock.c \
+	$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_reset.c \
+	$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_gpio.c \
+	$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpuart.c \
+	$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_common_arm.c \
+	$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_spc.c 
+INC += \
+	$(TOP)/$(BOARD_PATH) \
+	$(TOP)/lib/CMSIS_5/CMSIS/Core/Include \
+	$(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT) \
+	$(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers 
+	
+
+SRC_S += $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/startup_$(MCU_CORE).S
diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h
index e589c4c86..21ae3a71e 100644
--- a/src/common/tusb_mcu.h
+++ b/src/common/tusb_mcu.h
@@ -100,6 +100,13 @@
   #define TUP_DCD_ENDPOINT_MAX    8
   #define TUP_RHPORT_HIGHSPEED    1
 
+#elif TU_CHECK_MCU(OPT_MCU_MCXA)
+  // USB0 is chipidea FS
+  #define TUP_USBIP_CHIPIDEA_FS
+  #define TUP_USBIP_CHIPIDEA_FS_MCXA
+
+  #define TUP_DCD_ENDPOINT_MAX    16
+
 #elif TU_CHECK_MCU(OPT_MCU_MIMXRT1XXX)
   #define TUP_USBIP_CHIPIDEA_HS
   #define TUP_USBIP_EHCI
diff --git a/src/portable/chipidea/ci_fs/ci_fs_mcxa.h b/src/portable/chipidea/ci_fs/ci_fs_mcxa.h
new file mode 100644
index 000000000..81786efdf
--- /dev/null
+++ b/src/portable/chipidea/ci_fs/ci_fs_mcxa.h
@@ -0,0 +1,47 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2023 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+#ifndef _CI_FS_MCXA_H
+#define _CI_FS_MCXA_H
+
+#include "fsl_device_registers.h"
+
+#define CI_FS_REG(_port)        ((ci_fs_regs_t*) USB0_BASE)
+#define CI_REG                  CI_FS_REG(0)
+
+void dcd_int_enable(uint8_t rhport)
+{
+  (void) rhport;
+  NVIC_EnableIRQ(USB0_IRQn);
+}
+
+void dcd_int_disable(uint8_t rhport)
+{
+  (void) rhport;
+  NVIC_DisableIRQ(USB0_IRQn);
+}
+
+#endif
diff --git a/src/portable/chipidea/ci_fs/dcd_ci_fs.c b/src/portable/chipidea/ci_fs/dcd_ci_fs.c
index 9327e09d8..08e73711f 100644
--- a/src/portable/chipidea/ci_fs/dcd_ci_fs.c
+++ b/src/portable/chipidea/ci_fs/dcd_ci_fs.c
@@ -35,6 +35,8 @@
   #include "ci_fs_kinetis.h"
 #elif defined(TUP_USBIP_CHIPIDEA_FS_MCX)
   #include "ci_fs_mcx.h"
+#elif defined(TUP_USBIP_CHIPIDEA_FS_MCXA)
+  #include "ci_fs_mcxa.h"
 #else
   #error "MCU is not supported"
 #endif
diff --git a/src/tusb_option.h b/src/tusb_option.h
index 767323bdd..fe9c44e96 100644
--- a/src/tusb_option.h
+++ b/src/tusb_option.h
@@ -175,6 +175,7 @@
 
 // NXP LPC MCX
 #define OPT_MCU_MCXN9            2300  ///< NXP MCX N9 Series
+#define OPT_MCU_MCXA             2301  ///< NXP MCX A Series
 
 // Check if configured MCU is one of listed
 // Apply _TU_CHECK_MCU with || as separator to list of input