able to build with newly added lwip folder

2 files changed, 76 insertions, 0 deletions

diff --git a/demos/bsp/boards/board.c b/demos/bsp/boards/board.c
index 31186c35a..99497400d 100644
--- a/demos/bsp/boards/board.c
+++ b/demos/bsp/boards/board.c
@@ -48,6 +48,17 @@ void SysTick_Handler (void)
 }
 #endif
 
+// FIXME refractor
+void boardGetMACaddr(uint8_t *macaddr)
+{
+	macaddr[0] = BOARD_MAC_ADDR0;
+	macaddr[1] = BOARD_MAC_ADDR1;
+	macaddr[2] = BOARD_MAC_ADDR2;
+	macaddr[3] = BOARD_MAC_ADDR3;
+	macaddr[4] = BOARD_MAC_ADDR4;
+	macaddr[5] = BOARD_MAC_ADDR5;
+}
+
 void check_failed(uint8_t *file, uint32_t line)
 {
   (void) file;
diff --git a/demos/bsp/boards/embedded_artists/board_ea4357.h b/demos/bsp/boards/embedded_artists/board_ea4357.h
index 56a82cb00..138e6e199 100644
--- a/demos/bsp/boards/embedded_artists/board_ea4357.h
+++ b/demos/bsp/boards/embedded_artists/board_ea4357.h
@@ -63,11 +63,76 @@
 #include "lpc43xx_uart.h"
 #include "lpc43xx_i2c.h"
 
+
 #include "oem_base_board/pca9532.h" // LEDs
 
 #define CFG_PRINTF_TARGET       PRINTF_TARGET_SWO
 //#define CFG_PRINTF_TARGET       PRINTF_TARGET_UART
 
+/*=========================================================================
+    HARDWARE MAC ADDRESS
+    -----------------------------------------------------------------------*/
+	#define BOARD_MAC_ADDR0 0x00
+	#define BOARD_MAC_ADDR1 0x10
+	#define BOARD_MAC_ADDR2 0x20
+	#define BOARD_MAC_ADDR3 0x30
+	#define BOARD_MAC_ADDR4 0x40
+	#define BOARD_MAC_ADDR5 0x50
+/*=========================================================================*/
+
+/*=========================================================================
+    EMAC CONFIGURATION
+    -----------------------------------------------------------------------*/
+	/*  The PHY address connected the to MII/RMII */
+	#define LPC_PHYDEF_PHYADDR 1    /**< The PHY address on the PHY device. */
+
+	/*  Enable autonegotiation mode.
+	 *  If this is enabled, the PHY will attempt to auto-negotiate the
+	 *  best link mode if the PHY supports it. If this is not enabled,
+	 *  the PHY_USE_FULL_DUPLEX and PHY_USE_100MBS defines will be
+	 *  used to select the link mode. Note that auto-negotiation may
+	 *  take a few seconds to complete.
+	 */
+	#define PHY_USE_AUTONEG 1 /**< Enables auto-negotiation mode. */
+
+	/*  Sets up the PHY interface to either full duplex operation or
+	 *  half duplex operation if PHY_USE_AUTONEG is not enabled.
+	 */
+	#define PHY_USE_FULL_DUPLEX 1 /**< Sets duplex mode to full. */
+
+	/*  Sets up the PHY interface to either 100MBS operation or 10MBS
+	 *  operation if PHY_USE_AUTONEG is not enabled.
+	 */
+	#define PHY_USE_100MBS 1 /**< Sets data rate to 100Mbps. */
+
+	/*  Selects RMII or MII connection type in the EMAC peripheral */
+	#define LPC_EMAC_RMII 1   /**< Use the RMII or MII driver variant */
+
+	/*  Defines the number of descriptors used for RX */
+	#define LPC_NUM_BUFF_RXDESCS 20
+
+	/*  Defines the number of descriptors used for TX */
+	#define LPC_NUM_BUFF_TXDESCS 20
+
+	/*  Enables slow speed memory buffering
+	 *  Enable this define if you expect to transfer packets directly
+	 *  from SPI FLASH or any slower memory. This will add a check
+	 *  before queueing up the transfer pbuf to make sure the packet
+	 *  is not in slow memoey (defined by the LPC_SLOWMEM_ARRAY). If
+	 *  the packet does exists in slow memory, a pbuf will be created
+	 *  in the PBUF_RAM pool, copied to it, and sent from there.
+	 */
+	#define LPC_CHECK_SLOWMEM 0
+
+	/*  Array of slow memory addresses for LPC_CHECK_SLOWMEM
+	 *  Define the array - start and ending address - for the slow
+	 *  memory regions in the system that need pbuf copies.
+	 *
+	 *  Not defined since LPC_CHECK_SLOWMEM = 0.
+	 */
+	#define LPC_SLOWMEM_ARRAY
+/*=========================================================================*/
+
 #ifdef __cplusplus
  }
 #endif