clean up example to use CFG_TUD_ENABLED + CFG_TUD_MAX_SPEED instead of CFG_TUSB_RHPORT0_MODE

2 files changed, 38 insertions, 28 deletions

diff --git a/examples/device/audio_4_channel_mic/src/main.c b/examples/device/audio_4_channel_mic/src/main.c
index d085dd43a..9c94edd49 100644
--- a/examples/device/audio_4_channel_mic/src/main.c
+++ b/examples/device/audio_4_channel_mic/src/main.c
@@ -81,7 +81,8 @@ int main(void)
 {
   board_init();
 
-  tusb_init();
+  // init device stack on configured roothub port
+  tud_init(BOARD_TUD_RHPORT);
 
   // Init values
   sampFreq = AUDIO_SAMPLE_RATE;
diff --git a/examples/device/audio_4_channel_mic/src/tusb_config.h b/examples/device/audio_4_channel_mic/src/tusb_config.h
index 023faa7e2..0f5fbfef7 100644
--- a/examples/device/audio_4_channel_mic/src/tusb_config.h
+++ b/examples/device/audio_4_channel_mic/src/tusb_config.h
@@ -30,6 +30,20 @@
 extern "C" {
 #endif
 
+//--------------------------------------------------------------------+
+// Board Specific Configuration
+//--------------------------------------------------------------------+
+
+// RHPort number used for device can be defined by board.mk, default to port 0
+#ifndef BOARD_TUD_RHPORT
+#define BOARD_TUD_RHPORT      0
+#endif
+
+// RHPort max operational speed can defined by board.mk
+#ifndef BOARD_TUD_MAX_SPEED
+#define BOARD_TUD_MAX_SPEED   OPT_MODE_DEFAULT_SPEED
+#endif
+
 //--------------------------------------------------------------------
 // COMMON CONFIGURATION
 //--------------------------------------------------------------------
@@ -39,18 +53,19 @@ extern "C" {
 #error CFG_TUSB_MCU must be defined
 #endif
 
-#define CFG_TUSB_RHPORT0_MODE       OPT_MODE_DEVICE
-
 #ifndef CFG_TUSB_OS
-#define CFG_TUSB_OS                 OPT_OS_NONE
+#define CFG_TUSB_OS               OPT_OS_NONE
 #endif
 
 #ifndef CFG_TUSB_DEBUG
-#define CFG_TUSB_DEBUG              0
+#define CFG_TUSB_DEBUG            0
 #endif
 
-// CFG_TUSB_DEBUG is defined by compiler in DEBUG build
-// #define CFG_TUSB_DEBUG           0
+// Enable Device stack
+#define CFG_TUD_ENABLED           1
+
+// Default is max speed that hardware controller could support with on-chip PHY
+#define CFG_TUD_MAX_SPEED         BOARD_TUD_MAX_SPEED
 
 /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment.
  * Tinyusb use follows macros to declare transferring memory so that they can be put
@@ -64,7 +79,7 @@ extern "C" {
 #endif
 
 #ifndef CFG_TUSB_MEM_ALIGN
-#define CFG_TUSB_MEM_ALIGN          __attribute__ ((aligned(4)))
+#define CFG_TUSB_MEM_ALIGN        __attribute__ ((aligned(4)))
 #endif
 
 //--------------------------------------------------------------------
@@ -75,13 +90,7 @@ extern "C" {
 #define CFG_TUD_ENDPOINT0_SIZE    64
 #endif
 
-//------------- CLASS -------------//
-#define CFG_TUD_CDC               0
-#define CFG_TUD_MSC               0
-#define CFG_TUD_HID               0
-#define CFG_TUD_MIDI              0
 #define CFG_TUD_AUDIO             1
-#define CFG_TUD_VENDOR            0
 
 //--------------------------------------------------------------------
 // AUDIO CLASS DRIVER CONFIGURATION
@@ -89,23 +98,23 @@ extern "C" {
 
 // Have a look into audio_device.h for all configurations
 
-#define CFG_TUD_AUDIO_FUNC_1_DESC_LEN                                 TUD_AUDIO_MIC_FOUR_CH_DESC_LEN
+#define CFG_TUD_AUDIO_FUNC_1_DESC_LEN                 TUD_AUDIO_MIC_FOUR_CH_DESC_LEN
 
-#define CFG_TUD_AUDIO_FUNC_1_N_AS_INT                                 1
-#define CFG_TUD_AUDIO_FUNC_1_CTRL_BUF_SZ                              64
+#define CFG_TUD_AUDIO_FUNC_1_N_AS_INT                 1
+#define CFG_TUD_AUDIO_FUNC_1_CTRL_BUF_SZ              64
 
-#define CFG_TUD_AUDIO_ENABLE_EP_IN                                    1
-#define CFG_TUD_AUDIO_FUNC_1_N_BYTES_PER_SAMPLE_TX                    2         // This value is not required by the driver, it parses this information from the descriptor once the alternate interface is set by the host - we use it for the setup
-#define CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX                            4         // This value is not required by the driver, it parses this information from the descriptor once the alternate interface is set by the host - we use it for the setup
-#define CFG_TUD_AUDIO_EP_SZ_IN                                        (48 + 1) * CFG_TUD_AUDIO_FUNC_1_N_BYTES_PER_SAMPLE_TX * CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX      // 48 Samples (48 kHz) x 2 Bytes/Sample x CFG_TUD_AUDIO_N_CHANNELS_TX Channels - the Windows driver always needs an extra sample per channel of space more, otherwise it complains... found by trial and error
-#define CFG_TUD_AUDIO_FUNC_1_EP_IN_SZ_MAX                             CFG_TUD_AUDIO_EP_SZ_IN
-#define CFG_TUD_AUDIO_FUNC_1_EP_IN_SW_BUF_SZ                          CFG_TUD_AUDIO_EP_SZ_IN
+#define CFG_TUD_AUDIO_ENABLE_EP_IN                    1
+#define CFG_TUD_AUDIO_FUNC_1_N_BYTES_PER_SAMPLE_TX    2         // This value is not required by the driver, it parses this information from the descriptor once the alternate interface is set by the host - we use it for the setup
+#define CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX            4         // This value is not required by the driver, it parses this information from the descriptor once the alternate interface is set by the host - we use it for the setup
+#define CFG_TUD_AUDIO_EP_SZ_IN                        (48 + 1) * CFG_TUD_AUDIO_FUNC_1_N_BYTES_PER_SAMPLE_TX * CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX      // 48 Samples (48 kHz) x 2 Bytes/Sample x CFG_TUD_AUDIO_N_CHANNELS_TX Channels - the Windows driver always needs an extra sample per channel of space more, otherwise it complains... found by trial and error
+#define CFG_TUD_AUDIO_FUNC_1_EP_IN_SZ_MAX             CFG_TUD_AUDIO_EP_SZ_IN
+#define CFG_TUD_AUDIO_FUNC_1_EP_IN_SW_BUF_SZ          CFG_TUD_AUDIO_EP_SZ_IN
 
-#define CFG_TUD_AUDIO_ENABLE_ENCODING                                 1
-#define CFG_TUD_AUDIO_ENABLE_TYPE_I_ENCODING                          1
-#define CFG_TUD_AUDIO_FUNC_1_CHANNEL_PER_FIFO_TX                      2         // One I2S stream contains two channels, each stream is saved within one support FIFO - this value is currently fixed, the driver does not support a changing value
-#define CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO                        (CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX / CFG_TUD_AUDIO_FUNC_1_CHANNEL_PER_FIFO_TX)
-#define CFG_TUD_AUDIO_FUNC_1_TX_SUPP_SW_FIFO_SZ                       (CFG_TUD_AUDIO_EP_SZ_IN / CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO)
+#define CFG_TUD_AUDIO_ENABLE_ENCODING                 1
+#define CFG_TUD_AUDIO_ENABLE_TYPE_I_ENCODING          1
+#define CFG_TUD_AUDIO_FUNC_1_CHANNEL_PER_FIFO_TX      2         // One I2S stream contains two channels, each stream is saved within one support FIFO - this value is currently fixed, the driver does not support a changing value
+#define CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO        (CFG_TUD_AUDIO_FUNC_1_N_CHANNELS_TX / CFG_TUD_AUDIO_FUNC_1_CHANNEL_PER_FIFO_TX)
+#define CFG_TUD_AUDIO_FUNC_1_TX_SUPP_SW_FIFO_SZ       (CFG_TUD_AUDIO_EP_SZ_IN / CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO)
 
 #ifdef __cplusplus
 }