complete msc demo with lpc13uxx with readonly flash

1 files changed, 22 insertions, 2 deletions

diff --git a/tinyusb/class/msc.h b/tinyusb/class/msc.h
index d80e368e3..2c6adb2d6 100644
--- a/tinyusb/class/msc.h
+++ b/tinyusb/class/msc.h
@@ -55,9 +55,8 @@
 #endif

 

 //--------------------------------------------------------------------+

-// USB Class Constant

+// Mass Storage Class Constant

 //--------------------------------------------------------------------+

-

 /// MassStorage Subclass

 typedef enum {

   MSC_SUBCLASS_RBC = 1 , ///< Reduced Block Commands (RBC) T10 Project 1240-D

@@ -119,6 +118,10 @@ typedef ATTR_PACKED_STRUCT(struct) {
 

 STATIC_ASSERT(sizeof(msc_cmd_status_wrapper_t) == 13, "size is not correct");

 

+//--------------------------------------------------------------------+

+// SCSI Constant

+//--------------------------------------------------------------------+

+

 /// SCSI Command Operation Code

 typedef enum {

   SCSI_CMD_TEST_UNIT_READY              = 0x00, ///< The SCSI Test Unit Ready command is used to determine if a device is ready to transfer data (read/write), i.e. if a disk has spun up, if a tape is loaded and ready etc. The device does not perform a self-test operation.

@@ -133,6 +136,23 @@ typedef enum {
   SCSI_CMD_WRITE_10                     = 0x2A, ///< The WRITE (10) command requests thatthe device server transfer the specified logical block(s) from the data-out buffer and write them.

 }scsi_cmd_type_t;

 

+/// SCSI Sense Key

+typedef enum {

+  SCSI_SENSEKEY_NONE            = 0x00, ///< no specific Sense Key. This would be the case for a successful command

+  SCSI_SENSEKEY_RECOVERED_ERROR = 0x01, ///< ndicates the last command completed successfully with some recovery action performed by the disc drive.

+  SCSI_SENSEKEY_NOT_READY       = 0x02, ///< Indicates the logical unit addressed cannot be accessed.

+  SCSI_SENSEKEY_MEDIUM_ERROR    = 0x03, ///< Indicates the command terminated with a non-recovered error condition.

+  SCSI_SENSEKEY_HARDWARE_ERROR  = 0x04, ///< Indicates the disc drive detected a nonrecoverable hardware failure while performing the command or during a self test.

+  SCSI_SENSEKEY_ILLEGLA_REQUEST = 0x05, ///< Indicates an illegal parameter in the command descriptor block or in the additional parameters

+  SCSI_SENSEKEY_UNIT_ATTENTION  = 0x06, ///< Indicates the disc drive may have been reset.

+  SCSI_SENSEKEY_DATA_PROTECT    = 0x07, ///< Indicates that a command that reads or writes the medium was attempted on a block that is protected from this operation. The read or write operation is not performed.

+  SCSI_SENSEKEY_FIRMWARE_ERROR  = 0x08, ///< Vendor specific sense key.

+  SCSI_SENSEKEY_ABORTED_COMMAND = 0x0b, ///< Indicates the disc drive aborted the command.

+  SCSI_SENSEKEY_EQUAL           = 0x0c, ///< Indicates a SEARCH DATA command has satisfied an equal comparison.

+  SCSI_SENSEKEY_VOLUME_OVERFLOW = 0x0d, ///< Indicates a buffered peripheral device has reached the end of medium partition and data remains in the buffer that has not been written to the medium.

+  SCSI_SENSEKEY_MISCOMPARE      = 0x0e  ///< ndicates that the source data did not match the data read from the medium.

+}scsi_sense_key_type_t;

+

 //--------------------------------------------------------------------+

 // SCSI Primary Command (SPC-4)

 //--------------------------------------------------------------------+