diff options
Diffstat (limited to 'src')
| -rw-r--r-- | src/portable/synopsys/dwc2/dcd_dwc2.c | 361 | ||||
| -rw-r--r-- | src/portable/synopsys/dwc2/dwc2_type.h | 14 |
2 files changed, 182 insertions, 193 deletions
diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index 12466e5ba..897f81a42 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -67,7 +67,7 @@ // Debug level for DWC2 #define DWC2_DEBUG 2 -static TU_ATTR_ALIGNED(4) uint32_t _setup_packet[2]; +static CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(4) uint32_t _setup_packet[2]; typedef struct { uint8_t* buffer; @@ -81,10 +81,8 @@ static xfer_ctl_t xfer_status[DWC2_EP_MAX][2]; #define XFER_CTL_BASE(_ep, _dir) (&xfer_status[_ep][_dir]) // EP0 transfers are limited to 1 packet - larger sizes has to be split -static uint16_t ep0_pending[2]; // Index determines direction as tusb_dir_t type - -// TX FIFO RAM allocation so far in words - RX FIFO size is readily available from dwc2->grxfsiz -static uint16_t _allocated_fifo_words_tx; // TX FIFO size in words (IN EPs) +static uint16_t ep0_pending[2]; // Index determines direction as tusb_dir_t type +static uint16_t _dfifo_top; // top free location in FIFO RAM // Number of IN endpoints active static uint8_t _allocated_ep_in_count; @@ -92,68 +90,125 @@ static uint8_t _allocated_ep_in_count; // SOF enabling flag - required for SOF to not get disabled in ISR when SOF was enabled by static bool _sof_en; -// Calculate the RX FIFO size according to minimum recommendations from reference manual -// RxFIFO = (5 * number of control endpoints + 8) + -// ((largest USB packet used / 4) + 1 for status information) + -// (2 * number of OUT endpoints) + 1 for Global NAK -// with number of control endpoints = 1 we have -// RxFIFO = 15 + (largest USB packet used / 4) + 2 * number of OUT endpoints -// we double the largest USB packet size to be able to hold up to 2 packets -static inline uint16_t calc_grxfsiz(uint16_t max_ep_size, uint8_t ep_count) { - return 15 + 2 * (max_ep_size / 4) + 2 * ep_count; +//-------------------------------------------------------------------- +// DMA +//-------------------------------------------------------------------- + +TU_ATTR_ALWAYS_INLINE static inline bool dma_enabled(const dwc2_regs_t* dwc2) { + (void) dwc2; + // DMA doesn't support fifo transfer +#ifdef TUD_AUDIO_PREFER_RING_BUFFER +#if TUD_AUDIO_PREFER_RING_BUFFER + return false; +#endif +#endif + // Internal DMA only + return (dwc2->ghwcfg2_bm.arch == GHWCFG2_ARCH_INTERNAL_DMA); + // return false; +} + +TU_ATTR_ALWAYS_INLINE static inline uint16_t dma_cal_epfifo_base(uint8_t rhport) { + // Scatter/Gather DMA mode is not yet supported. Buffer DMA only need 1 words per endpoint direction + const dwc2_controller_t* dwc2_controller = &_dwc2_controller[rhport]; + return dwc2_controller->ep_fifo_size/4 - 2*dwc2_controller->ep_count; +} + +static void dma_setup_prepare(uint8_t rhport) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); + + if (dwc2->gsnpsid >= DWC2_CORE_REV_3_00a) { + if(dwc2->epout[0].doepctl & DOEPCTL_EPENA) { + return; + } + } + + // Receive only 1 packet + dwc2->epout[0].doeptsiz = (1 << DOEPTSIZ_STUPCNT_Pos) | (1 << DOEPTSIZ_PKTCNT_Pos) | (8 << DOEPTSIZ_XFRSIZ_Pos); + dwc2->epout[0].doepdma = (uintptr_t)_setup_packet; + dwc2->epout[0].doepctl |= DOEPCTL_EPENA | DOEPCTL_USBAEP; } -TU_ATTR_ALWAYS_INLINE static inline void fifo_flush_tx(dwc2_regs_t* dwc2, uint8_t epnum) { +//--------------------------------------------------------------------+ +// Data FIFO +//--------------------------------------------------------------------+ + +TU_ATTR_ALWAYS_INLINE static inline void dfifo_flush_tx(dwc2_regs_t* dwc2, uint8_t epnum) { // flush TX fifo and wait for it cleared dwc2->grstctl = GRSTCTL_TXFFLSH | (epnum << GRSTCTL_TXFNUM_Pos); while (dwc2->grstctl & GRSTCTL_TXFFLSH_Msk) {} } -TU_ATTR_ALWAYS_INLINE static inline void fifo_flush_rx(dwc2_regs_t* dwc2) { +TU_ATTR_ALWAYS_INLINE static inline void dfifo_flush_rx(dwc2_regs_t* dwc2) { // flush RX fifo and wait for it cleared dwc2->grstctl = GRSTCTL_RXFFLSH; while (dwc2->grstctl & GRSTCTL_RXFFLSH_Msk) {} } -static bool fifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) { +/* USB Data FIFO Layout + + The FIFO is split up into + - EPInfo: for storing DMA metadata, only required when use DMA. Maximum size is called + EP_LOC_CNT = ep_fifo_size - ghwcfg3.dfifo_depth. For value less than EP_LOC_CNT, gdfifocfg must be configured before + gahbcfg.dmaen is set + - Buffer mode: 1 word per endpoint direction + - Scatter/Gather DMA: 4 words per endpoint direction + - TX FIFO: one fifo for each IN endpoint. Size is dynamic depending on packet size, starting from top with EP0 IN. + - Shared RX FIFO: a shared fifo for all OUT endpoints. Typically, can hold up to 2 packets of the largest EP size. + + We allocated TX FIFO from top to bottom (using top pointer), this to allow the RX FIFO to grow dynamically which is + possible since the free space is located between the RX and TX FIFOs. + + ---------------- ep_fifo_size + | EPInfo | + | for DMA | + |-------------|-- gdfifocfg.EPINFOBASE (max is ghwcfg3.dfifo_depth) + | IN FIFO 0 | + | control | + |-------------| + | IN FIFO 1 | + |-------------| + | . . . . | + |-------------| + | IN FIFO n | + |-------------| + | FREE | + |-------------|-- GRXFSIZ (expandable) + | OUT FIFO | + | ( Shared ) | + --------------- 0 + + According to "FIFO RAM allocation" section in RM, FIFO RAM are allocated as follows (each word 32-bits): + - Each EP IN needs at least max packet size + - All EP OUT shared a unique OUT FIFO which uses (for Slave or Buffer DMA, Scatt/Gather DMA use different formula): + - 13 for setup packets + control words (up to 3 setup packets). + - 1 for global NAK (not required/used here). + - Largest-EPsize / 4 + 1. ( FS: 64 bytes, HS: 512 bytes). Recommended is "2 x (Largest-EPsize/4) + 1" + - 2 for each used OUT endpoint + + Therefore GRXFSIZ = 13 + 1 + 2 x (Largest-EPsize/4 + 1) + 2 x EPOUTnum +*/ + +TU_ATTR_ALWAYS_INLINE static inline uint16_t calc_grxfsiz(uint16_t largest_ep_size, uint8_t ep_count) { + return 13 + 1 + 2 * ((largest_ep_size / 4) + 1) + 2 * ep_count; +} + +static bool dfifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) { dwc2_regs_t* dwc2 = DWC2_REG(rhport); - uint8_t const ep_count = _dwc2_controller[rhport].ep_count; + const dwc2_controller_t* dwc2_controller = &_dwc2_controller[rhport]; + uint8_t const ep_count = dwc2_controller->ep_count; uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); TU_ASSERT(epnum < ep_count); uint16_t fifo_size = tu_div_ceil(packet_size, 4); - - // "USB Data FIFOs" section in reference manual - // Peripheral FIFO architecture - // - // --------------- 320 or 1024 ( 1280 or 4096 bytes ) - // | IN FIFO 0 | - // --------------- (320 or 1024) - 16 - // | IN FIFO 1 | - // --------------- (320 or 1024) - 16 - x - // | . . . . | - // --------------- (320 or 1024) - 16 - x - y - ... - z - // | IN FIFO MAX | - // --------------- - // | FREE | - // --------------- GRXFSIZ - // | OUT FIFO | - // | ( Shared ) | - // --------------- 0 - // - // In FIFO is allocated by following rules: - // - IN EP 1 gets FIFO 1, IN EP "n" gets FIFO "n". if (dir == TUSB_DIR_OUT) { // Calculate required size of RX FIFO - uint16_t const sz = calc_grxfsiz(4 * fifo_size, ep_count); - - // If size_rx needs to be extended check if possible and if so enlarge it - if (dwc2->grxfsiz < sz) { - TU_ASSERT(sz + _allocated_fifo_words_tx <= _dwc2_controller[rhport].ep_fifo_size / 4); + uint16_t const new_sz = calc_grxfsiz(4 * fifo_size, ep_count); - // Enlarge RX FIFO - dwc2->grxfsiz = sz; + // If size_rx needs to be extended check if there is enough free space + if (dwc2->grxfsiz < new_sz) { + TU_ASSERT(new_sz <= _dfifo_top); + dwc2->grxfsiz = new_sz; // Enlarge RX FIFO } } else { // Check IN endpoints concurrently active limit @@ -162,59 +217,48 @@ static bool fifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) { _allocated_ep_in_count++; } - // Note if The TXFELVL is configured as half empty. In order - // to be able to write a packet at that point, the fifo must be twice the max_size. + // If The TXFELVL is configured as half empty, the fifo must be twice the max_size. if ((dwc2->gahbcfg & GAHBCFG_TXFELVL) == 0) { fifo_size *= 2; } // Check if free space is available - TU_ASSERT(_allocated_fifo_words_tx + fifo_size + dwc2->grxfsiz <= _dwc2_controller[rhport].ep_fifo_size / 4); - _allocated_fifo_words_tx += fifo_size; - TU_LOG(DWC2_DEBUG, " Allocated %u bytes at offset %" PRIu32, fifo_size * 4, - _dwc2_controller[rhport].ep_fifo_size - _allocated_fifo_words_tx * 4); + TU_ASSERT(_dfifo_top >= fifo_size + dwc2->grxfsiz); + _dfifo_top -= fifo_size; + TU_LOG(DWC2_DEBUG, " TX FIFO %u: allocated %u words at offset %u\r\n", epnum, fifo_size, _dfifo_top); - // DIEPTXF starts at FIFO #1. // Both TXFD and TXSA are in unit of 32-bit words. - dwc2->dieptxf[epnum - 1] = (fifo_size << DIEPTXF_INEPTXFD_Pos) | - (_dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx); + if (epnum == 0) { + dwc2->dieptxf0 = (fifo_size << DIEPTXF0_TX0FD_Pos) | _dfifo_top; + } else { + // DIEPTXF starts at FIFO #1. + dwc2->dieptxf[epnum - 1] = (fifo_size << DIEPTXF_INEPTXFD_Pos) | _dfifo_top; + } } return true; } -static inline bool dma_enabled(uint8_t rhport) -{ - // DMA doesn't support fifo transfer -#ifdef TUD_AUDIO_PREFER_RING_BUFFER -#if TUD_AUDIO_PREFER_RING_BUFFER - return false; -#endif -#endif - dwc2_regs_t* dwc2 = DWC2_REG(rhport); - // Internal DMA only - return (dwc2->ghwcfg2_bm.arch == 2); -} - -static void dma_stpkt_rx(uint8_t rhport) -{ +static void dfifo_init(uint8_t rhport) { + const dwc2_controller_t* dwc2_controller = &_dwc2_controller[rhport]; dwc2_regs_t* dwc2 = DWC2_REG(rhport); + dwc2->grxfsiz = calc_grxfsiz(CFG_TUD_ENDPOINT0_SIZE, dwc2_controller->ep_count); - if (dwc2->gsnpsid >= DWC2_CORE_REV_3_00a) { - if(dwc2->epout[0].doepctl & DOEPCTL_EPENA) - return; + if(dma_enabled(dwc2)) { + // DMA use last DFIFO to store metadata + _dfifo_top = dma_cal_epfifo_base(rhport); + }else { + _dfifo_top = dwc2_controller->ep_fifo_size / 4; } - // Receive only 1 packet - dwc2->epout[0].doeptsiz = 0; - dwc2->epout[0].doeptsiz |= (1 << DOEPTSIZ_STUPCNT_Pos); - dwc2->epout[0].doeptsiz |= 8; - dwc2->epout[0].doeptsiz |= (1 << DOEPTSIZ_PKTCNT_Pos); - dwc2->epout[0].doepdma = (uintptr_t)_setup_packet; - - dwc2->epout[0].doepctl |= DOEPCTL_EPENA | DOEPCTL_USBAEP; + // Allocate FIFO for EP0 IN + dfifo_alloc(rhport, 0x80, CFG_TUD_ENDPOINT0_SIZE); } +//-------------------------------------------------------------------- +// Endpoint +//-------------------------------------------------------------------- + static void edpt_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) { dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const epnum = tu_edpt_number(p_endpoint_desc->bEndpointAddress); @@ -235,7 +279,7 @@ static void edpt_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoin dwc2->daintmsk |= TU_BIT(DAINTMSK_OEPM_Pos + epnum); } else { dwc2->epin[epnum].diepctl = dxepctl | (epnum << DIEPCTL_TXFNUM_Pos); - dwc2->daintmsk |= (1 << (DAINTMSK_IEPM_Pos + epnum)); + dwc2->daintmsk |= TU_BIT(DAINTMSK_IEPM_Pos + epnum); } } @@ -265,7 +309,7 @@ static void edpt_disable(uint8_t rhport, uint8_t ep_addr, bool stall) { } // Flush the FIFO, and wait until we have confirmed it cleared. - fifo_flush_tx(dwc2, epnum); + dfifo_flush_tx(dwc2, epnum); } else { dwc2_epout_t* epout = dwc2->epout; @@ -318,88 +362,27 @@ static void bus_reset(uint8_t rhport) { } } - fifo_flush_tx(dwc2, 0x10); // all tx fifo - fifo_flush_rx(dwc2); + dfifo_flush_tx(dwc2, 0x10); // all tx fifo + dfifo_flush_rx(dwc2); // 3. Set up interrupt mask dwc2->daintmsk = TU_BIT(DAINTMSK_OEPM_Pos) | TU_BIT(DAINTMSK_IEPM_Pos); dwc2->doepmsk = DOEPMSK_STUPM | DOEPMSK_XFRCM; dwc2->diepmsk = DIEPMSK_TOM | DIEPMSK_XFRCM; - // "USB Data FIFOs" section in reference manual - // Peripheral FIFO architecture - // - // The FIFO is split up in a lower part where the RX FIFO is located and an upper part where the TX FIFOs start. - // We do this to allow the RX FIFO to grow dynamically which is possible since the free space is located - // between the RX and TX FIFOs. This is required by ISO OUT EPs which need a bigger FIFO than the standard - // configuration done below. - // - // Dynamically FIFO sizes are of interest only for ISO EPs since all others are usually not opened and closed. - // All EPs other than ISO are opened as soon as the driver starts up i.e. when the host sends a - // configure interface command. Hence, all IN EPs other the ISO will be located at the top. IN ISO EPs are usually - // opened when the host sends an additional command: setInterface. At this point in time - // the ISO EP will be located next to the free space and can change its size. In case more IN EPs change its size - // an additional memory - // - // --------------- 320 or 1024 ( 1280 or 4096 bytes ) - // | IN FIFO 0 | - // --------------- (320 or 1024) - 16 - // | IN FIFO 1 | - // --------------- (320 or 1024) - 16 - x - // | . . . . | - // --------------- (320 or 1024) - 16 - x - y - ... - z - // | IN FIFO MAX | - // --------------- - // | FREE | - // --------------- GRXFSIZ - // | OUT FIFO | - // | ( Shared ) | - // --------------- 0 - // - // According to "FIFO RAM allocation" section in RM, FIFO RAM are allocated as follows (each word 32-bits): - // - Each EP IN needs at least max packet size, 16 words is sufficient for EP0 IN - // - // - All EP OUT shared a unique OUT FIFO which uses - // - 13 for setup packets + control words (up to 3 setup packets). - // - 1 for global NAK (not required/used here). - // - Largest-EPsize / 4 + 1. ( FS: 64 bytes, HS: 512 bytes). Recommended is "2 x (Largest-EPsize/4) + 1" - // - 2 for each used OUT endpoint - // - // Therefore GRXFSIZ = 13 + 1 + 1 + 2 x (Largest-EPsize/4) + 2 x EPOUTnum - // - FullSpeed (64 Bytes ): GRXFSIZ = 15 + 2 x 16 + 2 x ep_count = 47 + 2 x ep_count - // - Highspeed (512 bytes): GRXFSIZ = 15 + 2 x 128 + 2 x ep_count = 271 + 2 x ep_count - // - // NOTE: Largest-EPsize & EPOUTnum is actual used endpoints in configuration. Since DCD has no knowledge - // of the overall picture yet. We will use the worst scenario: largest possible + ep_count - // - // For Isochronous, largest EP size can be 1023/1024 for FS/HS respectively. In addition if multiple ISO - // are enabled at least "2 x (Largest-EPsize/4) + 1" are recommended. Maybe provide a macro for application to - // overwrite this. - - // EP0 out max is 64 - dwc2->grxfsiz = calc_grxfsiz(64, ep_count); - - // Setup the control endpoint 0 - _allocated_fifo_words_tx = 16; - - // DMA needs extra space for processing - if(dma_enabled(rhport)) { - uint16_t reserved = _dwc2_controller[rhport].ep_fifo_size / 4- dwc2->ghwcfg3_bm.total_fifo_size; - _allocated_fifo_words_tx += reserved; - } - - // Control IN uses FIFO 0 with 64 bytes ( 16 32-bit word ) - dwc2->dieptxf0 = (16 << DIEPTXF0_TX0FD_Pos) | (_dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx); + dfifo_init(rhport); // Fixed control EP0 size to 64 bytes dwc2->epin[0].diepctl &= ~(0x03 << DIEPCTL_MPSIZ_Pos); + dwc2->epout[0].doepctl &= ~(0x03 << DOEPCTL_MPSIZ_Pos); + xfer_status[0][TUSB_DIR_OUT].max_size = 64; xfer_status[0][TUSB_DIR_IN].max_size = 64; - dwc2->epout[0].doeptsiz |= (3 << DOEPTSIZ_STUPCNT_Pos); - - if(dma_enabled(rhport)) { - dma_stpkt_rx(rhport); + if(dma_enabled(dwc2)) { + dma_setup_prepare(rhport); + } else { + dwc2->epout[0].doeptsiz |= (3 << DOEPTSIZ_STUPCNT_Pos); } dwc2->gintmsk |= GINTMSK_OEPINT | GINTMSK_IEPINT; @@ -427,7 +410,7 @@ static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t c epin[epnum].dieptsiz = (num_packets << DIEPTSIZ_PKTCNT_Pos) | ((total_bytes << DIEPTSIZ_XFRSIZ_Pos) & DIEPTSIZ_XFRSIZ_Msk); - if(dma_enabled(rhport)) { + if(dma_enabled(dwc2)) { epin[epnum].diepdma = (uintptr_t)xfer->buffer; // For ISO endpoint set correct odd/even bit for next frame. @@ -468,7 +451,7 @@ static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t c epout[epnum].doepctl |= (odd_frame_now ? DOEPCTL_SD0PID_SEVNFRM_Msk : DOEPCTL_SODDFRM_Msk); } - if(dma_enabled(rhport)) { + if(dma_enabled(dwc2)) { epout[epnum].doepdma = (uintptr_t)xfer->buffer; } @@ -599,7 +582,9 @@ static void phy_hs_init(dwc2_regs_t* dwc2) { // XCVRDLY: transceiver delay between xcvr_sel and txvalid during device chirp is required // when using with some PHYs such as USB334x (USB3341, USB3343, USB3346, USB3347) - if (dwc2->ghwcfg2_bm.hs_phy_type == HS_PHY_TYPE_ULPI) dcfg |= DCFG_XCVRDLY; + if (dwc2->ghwcfg2_bm.hs_phy_type == HS_PHY_TYPE_ULPI) { + dcfg |= DCFG_XCVRDLY; + } dwc2->dcfg = dcfg; } @@ -625,12 +610,9 @@ void dcd_init(uint8_t rhport) { dwc2_regs_t* dwc2 = DWC2_REG(rhport); // Check Synopsys ID register, failed if controller clock/power is not enabled - if (!check_dwc2(dwc2)) return; + TU_ASSERT(check_dwc2(dwc2), ); dcd_disconnect(rhport); - // max number of endpoints & total_fifo_size are: - // hw_cfg2->num_dev_ep, hw_cfg2->total_fifo_size - if (phy_hs_supported(dwc2)) { phy_hs_init(dwc2); // Highspeed } else { @@ -660,8 +642,8 @@ void dcd_init(uint8_t rhport) { // (non zero-length packet), send STALL back and discard. dwc2->dcfg |= DCFG_NZLSOHSK; - fifo_flush_tx(dwc2, 0x10); // all tx fifo - fifo_flush_rx(dwc2); + dfifo_flush_tx(dwc2, 0x10); // all tx fifo + dfifo_flush_rx(dwc2); // Clear all interrupts uint32_t int_mask = dwc2->gintsts; @@ -670,20 +652,24 @@ void dcd_init(uint8_t rhport) { dwc2->gotgint |= int_mask; // Required as part of core initialization. - dwc2->gintmsk = GINTMSK_OTGINT | GINTMSK_RXFLVLM | - GINTMSK_USBSUSPM | GINTMSK_USBRST | GINTMSK_ENUMDNEM | GINTMSK_WUIM; + dwc2->gintmsk = GINTMSK_OTGINT | GINTMSK_USBSUSPM | GINTMSK_USBRST | GINTMSK_ENUMDNEM | GINTMSK_WUIM; // Configure TX FIFO empty level for interrupt. Default is complete empty dwc2->gahbcfg |= GAHBCFG_TXFELVL; - // Enable global interrupt - dwc2->gahbcfg |= GAHBCFG_GINT; + if (dma_enabled(dwc2)) { + const uint16_t epinfo_base = dma_cal_epfifo_base(rhport); + dwc2->gdfifocfg = (epinfo_base << GDFIFOCFG_EPINFOBASE_SHIFT) | epinfo_base; - if (dma_enabled(rhport)) { + // DMA seems to be only settable after a core reset dwc2->gahbcfg |= GAHBCFG_DMAEN | GAHBCFG_HBSTLEN_2; - dwc2->gintmsk &=~GINTMSK_RXFLVLM; + }else { + dwc2->gintmsk |= GINTMSK_RXFLVLM; } + // Enable global interrupt + dwc2->gahbcfg |= GAHBCFG_GINT; + // make sure we are in device mode // TU_ASSERT(!(dwc2->gintsts & GINTSTS_CMOD), ); @@ -783,7 +769,7 @@ void dcd_sof_enable(uint8_t rhport, bool en) { *------------------------------------------------------------------*/ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const* desc_edpt) { - TU_ASSERT(fifo_alloc(rhport, desc_edpt->bEndpointAddress, tu_edpt_packet_size(desc_edpt))); + TU_ASSERT(dfifo_alloc(rhport, desc_edpt->bEndpointAddress, tu_edpt_packet_size(desc_edpt))); edpt_activate(rhport, desc_edpt); return true; } @@ -812,32 +798,21 @@ void dcd_edpt_close_all(uint8_t rhport) { xfer_status[n][TUSB_DIR_IN].max_size = 0; } - // reset allocated fifo OUT - dwc2->grxfsiz = calc_grxfsiz(64, ep_count); - // reset allocated fifo IN - _allocated_fifo_words_tx = 16; - - fifo_flush_tx(dwc2, 0x10); // all tx fifo - fifo_flush_rx(dwc2); + dfifo_flush_tx(dwc2, 0x10); // all tx fifo + dfifo_flush_rx(dwc2); - // DMA needs extra space for processing - if(dma_enabled(rhport)) { - uint16_t reserved = _dwc2_controller[rhport].ep_fifo_size / 4- dwc2->ghwcfg3_bm.total_fifo_size; - _allocated_fifo_words_tx += reserved; - } + dfifo_init(rhport); // re-init dfifo } bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { - TU_ASSERT(fifo_alloc(rhport, ep_addr, largest_packet_size)); + TU_ASSERT(dfifo_alloc(rhport, ep_addr, largest_packet_size)); return true; } bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) { // Disable EP to clear potential incomplete transfers edpt_disable(rhport, p_endpoint_desc->bEndpointAddress, false); - edpt_activate(rhport, p_endpoint_desc); - return true; } @@ -904,8 +879,8 @@ void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) { void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { edpt_disable(rhport, ep_addr, true); - if((tu_edpt_number(ep_addr) == 0) && dma_enabled(rhport)) { - dma_stpkt_rx(rhport); + if((tu_edpt_number(ep_addr) == 0) && dma_enabled(DWC2_REG(rhport))) { + dma_setup_prepare(rhport); } } @@ -1075,13 +1050,15 @@ static void handle_epout_irq(uint8_t rhport) { uint32_t const doepint = epout->doepint; + TU_ASSERT((epout->doepint & DOEPINT_AHBERR) == 0, ); + // OUT XFER complete if (epout->doepint & DOEPINT_XFRC) { epout->doepint = DOEPINT_XFRC; xfer_ctl_t* xfer = XFER_CTL_BASE(n, TUSB_DIR_OUT); - if(dma_enabled(rhport)) { + if(dma_enabled(dwc2)) { if (doepint & DOEPINT_STUP) { // STPKTRX is only available for version from 3_00a if ((doepint & DOEPINT_STPKTRX) && (dwc2->gsnpsid > DWC2_CORE_REV_3_00a)) { @@ -1103,7 +1080,7 @@ static void handle_epout_irq(uint8_t rhport) { xfer->total_len -= remain; // this is ZLP, so prepare EP0 for next setup if(n == 0 && xfer->total_len == 0) { - dma_stpkt_rx(rhport); + dma_setup_prepare(rhport); } dcd_event_xfer_complete(rhport, n, xfer->total_len, XFER_RESULT_SUCCESS, true); @@ -1135,8 +1112,8 @@ static void handle_epout_irq(uint8_t rhport) { if ((doepint & DOEPINT_STPKTRX) && (dwc2->gsnpsid > DWC2_CORE_REV_3_00a)) { epout->doepint = DOEPINT_STPKTRX; } - if(dma_enabled(rhport) && (dwc2->gsnpsid > DWC2_CORE_REV_3_00a)) { - dma_stpkt_rx(rhport); + if(dma_enabled(dwc2) && (dwc2->gsnpsid > DWC2_CORE_REV_3_00a)) { + dma_setup_prepare(rhport); } dcd_event_setup_received(rhport, (uint8_t*) _setup_packet, true); @@ -1165,8 +1142,8 @@ static void handle_epin_irq(uint8_t rhport) { // Schedule another packet to be transmitted. edpt_schedule_packets(rhport, n, TUSB_DIR_IN, 1, ep0_pending[TUSB_DIR_IN]); } else { - if((n == 0) && dma_enabled(rhport)) { - dma_stpkt_rx(rhport); + if((n == 0) && dma_enabled(dwc2)) { + dma_setup_prepare(rhport); } dcd_event_xfer_complete(rhport, n | TUSB_DIR_IN_MASK, xfer->total_len, XFER_RESULT_SUCCESS, true); } diff --git a/src/portable/synopsys/dwc2/dwc2_type.h b/src/portable/synopsys/dwc2/dwc2_type.h index 244323b51..c21bf9e94 100644 --- a/src/portable/synopsys/dwc2/dwc2_type.h +++ b/src/portable/synopsys/dwc2/dwc2_type.h @@ -100,6 +100,12 @@ enum { FS_PHY_TYPE_ULPI, }; +enum { + GHWCFG2_ARCH_SLAVE_ONLY = 0, + GHWCFG2_ARCH_EXTERNAL_DMA, // 1 + GHWCFG2_ARCH_INTERNAL_DMA, // 2 +}; + typedef struct TU_ATTR_PACKED { uint32_t op_mode : 3; // 0: HNP and SRP | 1: SRP | 2: non-HNP, non-SRP @@ -134,7 +140,7 @@ typedef struct TU_ATTR_PACKED uint32_t otg_enable_hsic : 1; // 1: HSIC-capable with shared UTMI PHY interface | 0: non-HSIC uint32_t battery_charger_support : 1; // support battery charger uint32_t lpm_mode : 1; // LPC mode - uint32_t total_fifo_size : 16; // DFIFO depth value in terms of 32-bit words + uint32_t dfifo_depth : 16; // DFIFO depth - EP_LOC_CNT in terms of 32-bit words }dwc2_ghwcfg3_t; TU_VERIFY_STATIC(sizeof(dwc2_ghwcfg3_t) == 4, "incorrect size"); @@ -1240,6 +1246,12 @@ TU_VERIFY_STATIC(offsetof(dwc2_regs_t, fifo ) == 0x1000, "incorrect size"); #define GLPMCFG_ENBESL_Msk (0x1UL << GLPMCFG_ENBESL_Pos) // 0x10000000 #define GLPMCFG_ENBESL GLPMCFG_ENBESL_Msk // Enable best effort service latency +// GDFIFOCFG +#define GDFIFOCFG_EPINFOBASE_MASK (0xffff << 16) +#define GDFIFOCFG_EPINFOBASE_SHIFT 16 +#define GDFIFOCFG_GDFIFOCFG_MASK (0xffff << 0) +#define GDFIFOCFG_GDFIFOCFG_SHIFT 0 + /******************** Bit definition for DIEPEACHMSK1 register ********************/ #define DIEPEACHMSK1_XFRCM_Pos (0U) #define DIEPEACHMSK1_XFRCM_Msk (0x1UL << DIEPEACHMSK1_XFRCM_Pos) // 0x00000001 |