| Age | Commit message (Collapse) | Author |
|---|
|
hil-validate ran one hil-operator per board. That parallelizes at the wrong layer:
hil_test.py already schedules boards across host controllers and budgets concurrent
flashes and usbtest batteries per controller (FLASH_PARALLEL/USBTEST_PARALLEL), and
those permits live in one process - N parallel runs multiply the budget onto the same
uPD720201 cards for no wall-clock gain over one run that already parallelizes. The
workflow now spawns ONE operator with every board as repeated -b.
The operator no longer retypes the report table. Four consecutive max-effort review
rounds found ~15 defects in this file and every one was in reconstructing board
identity from transcribed prose: report rows are named per VARIANT (nanoch32v203 only
ever produces -fsdev/-usbfs rows), a variant need not start with its board's name,
lock contention is a `board-locked` cell rather than a phrase, and each fix introduced
the next round's bug - including a fake-green test that asserted an invariant with the
one input shape that could not break it. The new helper test/hil/helper/hil_summary.py
does the join where the roster lives and emits one machine verdict per board
({board, ran, pass, locked, detail}); the operator returns that JSON verbatim plus
`wedged`, the only field it authors, and the workflow reads fields, never parses a
string. Its cell classifier mirrors hil_test.py's own tally exactly: failures are
always marked ('fail' or a ❌ prefix, TestFail's contract), everything unmarked is a
pass - a passing test may return a plain metric cell like '13443 KB/s', and the
mirrored rule is what keeps a green table from becoming a red verdict.
hil_ci.sh kept only the LAST -b, so multi-board remote runs staged one board's
binaries and every other board died on the rig after its lock and flash slot were
spent. It now parses every -b spelling argparse accepts (with the -bt arms ordered
first, longest-match, so the <config>.failed retry form is never read as a board named
"t..."), pre-flights roster membership and build dirs for ALL boards before anything
is wiped or staged, warns per declared variant with no build dir (which hil_test.py
would silently green-skip), forwards HIL_* knobs as export lines in one %q word the
remote evals ('; '-joined so it round-trips under dash - an authorized
HIL_NO_BOARD_LOCK force must not silently no-op), keeps HIL_REPORT_DIR local because
the copy-backs look in REMOTE_DIR, and copies hil_report.json and the .failed re-run
spec back beside the markdown, deleting stale local copies first so a green run cannot
leave last run's spec looking current.
Retries preserve the fleet: the documented path is the <config>.failed spec, which
already begins with --accumulate; a fresh scoped re-run would unlink the report and
collapse the whole-fleet table to the retried boards alone.
The risky logic is executable, not argued about: .claude/workflows/test-hil-validate.mjs
pins the lookup/verdict helpers and runs in pre-commit (hil-validate-logic); nine
staging tests drive hil_ci.sh through an ssh stub that models the real thing (argv
joined into one string the remote re-splits, heredoc on stdin - the naive echo-stub
passed while the feature was broken); and deliberate mutations of the verdict logic
are all caught.
Validated on the rig: a 2-board run (usbtest 30/30 on both; the pre-fix classifier,
replayed against that run's real report, fails the fully-green stm32f723disco on its
two passing '13443 KB/s' cells), the .failed --accumulate retry (merged report kept
every earlier row), and a 10-run soak over random subsets of a 22-board pool - 43
board-slots, every failure signature matched pre-existing CI state or known flake,
zero tooling failures, no locks left behind.
|
|
dcd(ci_hs): stage the device address before priming the status stage
|
|
IMXRT1060RM 42.7.23 and UM10503 Table 478 both ask for the DEVICEADDR write
with USBADRA=1 to happen after the SET_ADDRESS data phase and before the
prime of the status stage, so the controller loads USBADR from its holding
register when the status stage is ACKed. The driver did it the other way
round, leaving a window between the ENDPTPRIME store and the DEVICEADDR
store: an IN answered inside that window ACKs with USBADRA still 0, so the
holding register is never consulted and the device keeps answering on
address 0 while the host has moved to the new one. Instruction timing alone
cannot open that window, but dcd_set_address() runs in task context, so any
interrupt landing between the two stores stretches it past a microframe.
Hardware discards a staged address on a SETUP or OUT to endpoint 0 and
zeroes USBADR on a bus reset, which covers a superseded SET_ADDRESS. What
it cannot cover is a SETUP latched before this write and still unconsumed
after the full CI_HS_BUSY_SPIN spin, which refuses the prime: condition 2
already fired for that earlier SETUP, so the stage would survive and load
USBADR on the next EP0 IN ACK of an unrelated transfer. USB 2.0 9.4.6 is
explicit that "the USB device does not change its device address until
after the Status stage of this request is completed successfully", so the
refused-prime path restores the previous USBADR rather than leaving a stage
armed. Restoring the previous value rather than writing zero keeps 9.4.6's
Address-state row correct, where a device already at a non-zero address
must stay there; on Linux that write is always a no-op, since hub_set_address
only issues SET_ADDRESS from USB_STATE_DEFAULT.
Cast dev_addr before the shift: it is uint8_t, promoted to int, so an
address of 64 or more reached the sign bit of a 32-bit int.
No errata applies: IMXRT1060CE_A Rev 1.3 lists only ERR050101 and ERR010661
for USB, IMXRT1060CE_B Rev 1.1 only ERR010661.
Validated on mimxrt1064_evk: 18/19 device+host tests, 6x usbtest 30/30, and
a 100-iteration forced re-enumeration A/B that is clean on both this change
and its parent (0/100 each). All 19 ci_hs boards build; unit tests 63/63;
PVS drops one diagnostic (the sign-bit shift) and adds none.
|
|
ci(circleci): key the toolchain cache off a file that always exists
|
|
ohci: fix double allocation of dummy TDs in gtd_find_free
|
|
Restore/Save Toolchain Cache have been failing on every job whose toolchain
is hosted on GitHub - arm-gcc, arm-clang, riscv-gcc, rx-gcc, ft9xx-gcc:
Restore Toolchain Cache
template: cacheKey:1:8: executing "cacheKey" at <checksum "toolchain_key">:
error calling checksum: open /home/circleci/project/tinyusb/toolchain_key:
no such file or directory
"Set toolchain url and key" only wrote toolchain_key when the URL was not a
github.com link, but both cache steps referenced {{ checksum "toolchain_key" }}
unconditionally, so for those toolchains the key could never be computed. The
job still went green because the build step does not depend on the cache, which
is why this went unnoticed - but the two steps are permanently red and the
toolchain is re-downloaded on every single run.
Key the cache on the toolchain name plus a checksum of toolchain.json instead.
That file is in the repo, so the checksum always resolves, and the key still
invalidates whenever a toolchain URL changes. toolchain_key is no longer needed.
Side effect worth calling out: GitHub-hosted toolchains are now cached rather
than skipped. That was the intent of the removed condition, but it is also what
broke the steps - CircleCI cannot skip a cache step on a value only known at
run time. Caching them also saves the repeated download.
|
|
|
|
UAC2: Add more terminal types
|
|
|
|
dcd(ci_hs): rework bus reset handling per the reference manual, and work around ERR050101
|
|
ERR050101: while an isochronous IN endpoint is active, an IN token addressed to
that same endpoint number on ANOTHER device sharing the host can silently
unprime one of this device's OUT endpoints - control, bulk, interrupt or
isochronous alike. NXP states it cannot be detected by software and raises no
interrupt, so the endpoint simply stops answering and the transfer never
completes.
The workaround is a uniqueness requirement rather than a particular number: the
isochronous IN endpoint must not share its number with any IN endpoint in use on
the bus. One family-wide constant therefore defeats it, since two affected
boards on the same hub then pick the same number and each becomes the other's
aggressor. CFG_TUSB_MIMXRT1XXX_ERRATA_ERR050101 is set only for the parts whose
errata list it - RT1015, RT1020, RT1024 and RT1050, where it is marked no fix
scheduled, plus RT1060 and RT1064 rev A - so RT1010 and the RT11xx family keep
the ordinary number and cannot collide with an affected board beside them.
Several affected boards on one hub can still be given distinct numbers with
-DEPNUM_ISO_IN.
The guard covers every example that has an isochronous IN endpoint: audio_test,
audio_4_channel_mic, uac2_headset, cdc_uac2, usbtest, video_capture and
video_capture_2ch. The video examples move the endpoint only when streaming
isochronously, since the bulk configuration is unaffected, and video_capture_2ch
takes two numbers because it has two streams.
The macro name follows CFG_TUSB_RP2_ERRATA_E2/E4/E15 already in tree, and its
is fixed, and which cannot be told apart at compile time - a way to define it to
0.
device_issues.rst records ERR050101 against every affected part with a link to
each errata sheet, and adds the LPC55S2x USB.3 speed-detection and USB.5
isochronous IN entries, neither of which TinyUSB works around. The branch's
design notes are included under docs/superpowers.
Verified: 340 wedge-free runs on mimxrt1064_evk, which previously wedged within
hours, and the macro resolving to endpoint 0x87 on mimxrt1064_evk against 0x83
on mimxrt1010_evk and stm32f407disco.
|
|
Flip the board to device-highspeed/host-fullspeed, matching lpcxpresso55s69
and the way it is cabled on the test rig, and add it to the rig pool with
the unique id read from its flash PFR. This is the first hardware coverage
the ip3511 high-speed device path has ever had, and it immediately exposed
the clear-stall type-bit bug fixed separately.
The port swap also exposed a build gap: family.mk only linked a host
controller for port 1, so make host builds on port 0 failed with undefined
references - mirror family.cmake and link the OHCI driver there. The board's
rhport defaults now come from family.cmake's guarded ones rather than a
duplicate copy, so a -D override on the command line wins.
|
|
The 8 KB main bank is packed tightly enough that only ~280 bytes remained above
.bss, and interrupt frames overflowed into the topmost task stack - a hard fault
in cdc_msc_freertos. Put the MSP at the top of the 2 KB USB SRAM bank, which
nothing else uses in either build system, so the stack no longer shrinks as .bss
grows. The Make build's CFG_TUSB_MEM_SECTION placement of endpoint buffers into
that bank is dropped so both build systems agree on the layout.
The headroom assert is written as an addition rather than a subtraction, since
linker script arithmetic is unsigned and an overflowing bank would underflow the
difference into a huge positive value and pass silently.
|
|
DEVCMDSTAT mixes read/write fields with write-1-to-clear latches, so a blind
read-modify-write writes a pending latch back as a one and silently clears it -
a setup consumed that way strands EP0. Mask the latches on every update.
The setup path follows the manual's order: acknowledge the latch, then read the
payload. The EP0 IN interrupt is cleared along with EP0 OUT, as the control
endpoint flowchart requires - a control IN completion latched before the setup
must not reach usbd after it, where it would be applied to the request the setup
just started and arm its status stage early.
The payload is copied a byte at a time out of a buffer now declared volatile:
the controller DMAs a new setup packet into it as soon as the latch is cleared,
and C orders volatile accesses only against each other, so gcc sinks a plain
memcpy below the guard read that follows at -O2 and -O3 - leaving only -Os, the
level CI builds, correct.
|
|
A refused transfer is a recoverable condition - a new setup superseding a
control response, for instance - rather than a bug, but every failure path
treated it as one. TU_ASSERT carries TU_BREAKPOINT, which is gated on a debugger
being attached rather than on CFG_TUSB_DEBUG, so on a rig where a probe is
always attached it halted the CPU even in release builds. Use TU_VERIFY on the
control transfer paths, including the multi-packet data stage continuation, and
drop the breakpoint from the endpoint transfer failure arm, which already marks
the endpoint ready again so the next transfer can proceed.
The result of usbd_control_xfer_cb() was separately dropped on the floor,
leaving EP0 neither armed nor stalled and nothing recorded. It is logged now,
and deliberately not stalled: a DCD refuses an EP0 prime when a newer setup is
already latched, and EP0 stalls are cleared by hardware when that setup arrives,
so a stall issued here would land after the auto-clear and stall the transfer
that superseded this one. The pending setup re-drives EP0 by itself.
|
|
A bus reset was detected only from the port change that ends it, which is late:
the manual asks the DCD to clear the endpoint semaphores, cancel every prime and
free the dTDs while the reset is still being driven. Enable the reset interrupt
and do all of that there, in the manual's order (IMXRT1060RM 42.5.6.2.1,
p.2394), including the two steps that were missing - confirming the port is
still being reset, and freeing the dTDs. A failed check means the cleanup
arrived late and the controller may be in an undefined state, so the manual's
remedy is carried out rather than noted: a controller reset, followed by the
full re-initialisation it then requires, since the reset detaches the device.
The port change that ends the reset is left with what the manual gives it, the
negotiated speed, which the new BUS_RESET_END event carries. A port change is
classified by the interrupt that preceded it: a suspend raises no port change of
its own, the resume that ends it does.
Every unbounded register spin is now bounded. They waited on bits the hardware
clears within a frame, but each could hang an interrupt handler outright on a
controller that had stopped responding. The endpoint flush follows all three
steps of IMXRT1060RM 42.5.6.6.5 (p.2413), repeating a flush the controller
refuses while a packet is in progress - previously reported as success.
EP0 setup handling is hardened alongside: the payload is copied out of the queue
head through the volatile qualifier before ENDPTSETUPSTAT is cleared, since that
clear releases the setup lockout and a back-to-back setup can overwrite the
buffer immediately after, and C orders volatile accesses only against each
other, so a plain memcpy may legally be sunk past the store.
There is deliberately no unplug detection. IMXRT1060RM 42.7.31 (p.2470) states a
zero Current Connect Status means the device "did not attach successfully or was
forcibly disconnected by the software writing a zero to the Run bit ... It does
not state the device being disconnected or suspended", so a cable pull raises no
port change at all; VBUS via OTGSC is the manual's disconnect indicator and is
board dependent.
Verified on mimxrt1064_evk: 30 forced bus resets each re-enumerating at high
speed with no descriptor errors, plus repeated full usbtest batteries at 30/30
across the series.
|
|
A driver that can see reset signalling begin has no way to say so: the only
event carries the negotiated speed, which does not exist until the reset
ends. On ChipIdea that left the stack believing it was still configured for
the whole reset window - 3 ms at minimum, tens of milliseconds in practice -
while the controller had already torn its endpoints down, so a class driver
writing in that window primed a disabled endpoint over a zeroed queue head.
Add DCD_EVENT_BUS_RESET_START for the leading edge and rename the existing
event to DCD_EVENT_BUS_RESET_END, keeping DCD_EVENT_BUS_RESET as an alias.
START is optional and END stays self-sufficient, so every other driver and
the unit tests are untouched.
|
|
This adds more standard terminal types that can
be used in descriptors to improve end user experience
when operating system can present more acurate
image for audio device terminal.
Signed-off-by: Jerzy Kasenberg <[email protected]>
|
|
read-doc skill: search the document library's database instead of the filesystem
|
|
Finding documents by walking the library tree misses anything the filename
does not carry - Calibre stores only a truncated title and the author there, so
the tags, series, publisher and description that hold most part numbers and
errata IDs are invisible to it. A zero-result tree search then reads as "the
document does not exist" rather than as a bad search; that happened here, and
led to a confident claim that a fully populated 14,000-file library was empty.
search.py queries metadata.db, ANDs its keywords across every metadata field
(including the stored filename), and prints the best matches first with the
exact path to read. Matching is NFKC + casefold, so a typed ASCII apostrophe or
mu reaches the titles that store the typographic ones.
Every printed path is checked on disk. Calibre renames <author>/<title> (<id>)
when metadata is edited and leaves the old directory behind, so a miss retries
by the stable book id before reporting MISSING - which distinguishes "the file
is not here right now" from "no such document". The gate tests for metadata.db
rather than the directory, since an unmounted or half-synced mountpoint is
still a directory.
Consumers that prescribed their own tree search - driver-reviewer, port-dev,
the driver-review workflow, and the calibre-library references in CLAUDE.md,
usbtest, etm-trace and target-debug - now point at the skill, which owns the
library's location.
|
|
hil, ci: contain a wedged USB stack instead of stranding the runner
|
|
Records the convention in CLAUDE.md -- deferred work is a SEPARATE scope that deserves
its own PR, written by another session, so it is handed off as a writing-plans doc in
docs/superpowers/followup/pr<NNN>-<topic>.md rather than accumulated in the PR that
found it.
Five handoffs from #3803: flasher_recover (convoy-safe recovery for J-Link boards, seven
validated on the rig), the blindness reporting gaps, the usbtest recovery reserve, the
IAR re-run spec, and the pci-rebind stranding question. Each carries what is already
established with its citations and measurements, what remains, and why it was split out.
One doc per follow-up, not one per PR: a per-PR file invites unrelated work into the
same document and rots as a unit.
|
|
Two things the rig taught us that the old guidance got wrong.
A usbfs ioctl wedged in D state cannot be freed on a running kernel. It holds
the device lock, so usb_disconnect() blocks behind it; reboot(2) walks
device_shutdown() and takes the same lock, so every userspace reboot stalls too.
Only sysrq b (emergency_restart, which skips device_shutdown) or hypervisor
action clears it -- all cited to the kernel source. The recovery ladder is
generic across rigs now (ci.lan, hifiphile, a bench PC) and ends at hypervisor
escalation only where host access exists. Two claims are corrected outright:
JLinkExe is NOT convoy-safe, and a park-flash cannot free a device-lock owner.
The hil skill's banner list is what an operator agent matches a report against,
so it enumerates the banners that actually exist, including the D-state note --
which is explicitly NOT a wedge, since a healthy in-flight testusb is
uninterruptible for most of every case and a concurrent CI battery would
otherwise turn a clean run red.
|
|
A wedged USB device used to take the whole HIL run with it. Every worker that
touched the poisoned node blocked uninterruptibly, the pool could not be joined,
map_async discarded every board's result, and the job ran to the GitHub ceiling
with no report at all -- while the self-hosted runner's single job slot stayed
occupied and every queued job waited behind it.
Bound the calls a worker makes itself. read_sysfs, bounded_open and run_cmd all
answer within a wall clock; read_sysfs distinguishes "absent" from "unknown",
because a blocked read is not evidence of absence, and caps stranded readers at
four (each costs a thread and an fd for the life of the process) after which the
worker declares itself blind. mtype, the gio unmount, the libmtp session and the
arecord/iperf reaps go through those bounds; the MTP session runs in a disposable
subprocess, since libmtp's ctypes calls block unkillably in D state.
Bound the run. A pool guard (HIL_POOL_TIMEOUT, 60 min) fires before any job
ceiling and still writes a report. When the pool will not shut down, the sweep
kills what the workers spawned -- descendants, not just direct children, since
flashers run in their own session -- confirms each kill actually landed, and
exits early so the runner is freed. Whatever survived is named in the report.
Deliberately shallow past that point. We do not re-scan process groups, prove
pid ownership, or escalate through sudo: a root-owned survivor is reported, not
force-killed, because signalling a pid we cannot prove is ours is the worse
failure, and the job ceiling backstops whatever this misses. A D-state holder
was never killable anyway.
Recover instead of reporting a wedge. A HUNG usbtest case reflashes its own DUT
through its roster flasher, but only where the flasher can reach its probe past
a poisoned node -- openocd pinned to a validated vid_pid, or esptool. Where it
cannot, the run says so rather than reserving budget for a path that cannot fire.
Raise the CI ceilings above the pool guard so the guard fires first and still
writes its report, and pin --retry 1 on every HIL leg: the guard is a flat
constant and does not scale with max_retry, so argparse's default of 3 would
triple the serialized usbtest tail against an unchanged guard.
Split the module: execution in hil_test/hil_flash/usbtest, infrastructure in
helper/ (locking, health, selection, shared bounded IO), and the two matrix
generators into .github/scripts/ -- ci_set_matrix.py sat in workflows/, where
GitHub treats every file as a workflow definition. 193 tests cover the bounded
paths, the kill ladder, the guard and the selector against synthetic /proc trees
and PATH-injected fakes; a real wedge cannot be manufactured on demand.
|
|
|
|
Fix HFP HIL reliability issue
|
|
|
|
Replace the duplicated per-MCU dispatch in dcd_init/hcd_init and the two
helper flavors (USB_Type access on iMX RT, raw offset 0x90 on LPC18/43)
with one SBUSCFG register field plus a per-header CI_HS_SET_AHB_BURST()
hook, compiled only where defined. The LPC USB0-only policy is now
visible at the macro definition.
|
|
midi2 device: complete the UMP stream discovery responder
|
|
clamp committed video payload size to streaming ep buffer
|
|
Co-authored-by: Copilot Autofix powered by AI <[email protected]>
Signed-off-by: HiFiPhile <[email protected]>
|
|
usbtmc: re-arm (or stall) the bulk-OUT endpoint after a USB488 TRIGGER message
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Text replies resume instead of dropping their tail packets, which used
to leave a Start/Continue sequence without an End. A new Function Block
Discovery now merges with a pending one instead of replacing it.
|
|
|
|
Adds the Device Identity Notification with an app callback, MIDI-CI
version and SysEx8 stream count in FB Info, honors the Endpoint
Discovery filter bitmap, and paces discovery replies by TX FIFO room.
|
|
A false return from tud_usbtmc_start_bus_read() here does not mean arming
failed: it means the endpoint is already armed, either because the
application re-armed it from its trigger callback or because a transfer is
still queued (usbd_edpt_xfer() reports failure when the endpoint is busy).
Both cases end in STATE_IDLE, so the state cannot disambiguate them either,
and stalling on the result would halt a healthy endpoint.
Co-Authored-By: Claude Opus 5 <[email protected]>
|
|
A single USB488 TRIGGER message left the bulk-OUT endpoint un-armed, so the
host's next bulk-OUT transfer timed out. The trigger itself succeeded
silently, so the failure surfaced on a later, unrelated command; only a
USBTMC device clear recovered it. The bundled examples/device/usbtmc
reproduced this as shipped.
Every other branch of the STATE_IDLE dispatch in usbtmcd_xfer_cb() leaves
the endpoint in a defined state: it either transitions out of STATE_IDLE so
a later tud_usbtmc_start_bus_read() can re-arm it, or it stalls and lets the
CLEAR_FEATURE(ENDPOINT_HALT) handler recover it. USBTMC_MSGID_USB488_TRIGGER
did neither, and because the state stayed STATE_IDLE, even an application
following the contract documented in usbtmc_device.h got a silent no-op from
tud_usbtmc_start_bus_read().
Transition to STATE_NAK so the re-arm can take effect, and stall the
endpoint when trigger is unsupported or the application callback rejects it,
matching the existing handling for messages the driver cannot process. The
callback result is deliberately not wrapped in TU_VERIFY(), which would
return before the stall/re-arm and reintroduce the same hang.
Since the driver now re-arms after a trigger, drop tud_usbtmc_msg_trigger_cb
from the list of callbacks after which the application must do so.
Fixes #3821
Co-Authored-By: Claude Opus 5 <[email protected]>
|
|
usbd: fix queued-setup counter leak when the event queue is full
|
|
An XFER_COMPLETE dropped by a full event queue leaves its endpoint's
BUSY|CLAIMED state set forever - the consumer that normally clears it
never sees the event, so usbd_edpt_claim()/usbd_edpt_xfer() fail from
then on and the class never re-arms the endpoint. Clear both flags when
the enqueue fails: the completion is lost either way, but the endpoint
stays usable.
Unit test: arm a bulk endpoint, drop its completion against a full
queue, verify the endpoint can be claimed and re-armed.
|
|
hw/bsp/lpc55: implement board_get_unique_id from flash PFR UUID
|
|
Read the 128-bit device UUID from the flash PFR region at 0x0009FC70
(UM11126 rev 2.1, section 48.8) rather than falling back to the fixed
weak default in hw/bsp/board.c.
Verified on lpcxpresso55s69: cdc_msc enumerates with SerialNumber
E059C3E208F9B955B3BA4C5CC7F3D13D, matching the uid already recorded for
that board in test/hil/local.json.
|
|
A SETUP counted before a bus reset must not be carried across it: the
consumer would either skip a post-reset SETUP (count drained by the
stale entry) or, if the count leaked high for any other reason, skip
them all. usbd_reset() now zeroes the counter; the consumer already
guards on zero, and any pre-reset SETUP still in the queue is stale by
definition and correctly discarded.
|
|
A SETUP arriving while the event queue is full is silently dropped by
queue_event(), but _usbd_queued_setup has already been incremented. The
leaked count makes the event handler skip every subsequent SETUP
("Skipped since there is other SETUP in queue") forever: EP0 stays deaf
until tud_init() while the device otherwise looks alive - enumerated,
endpoints armed. Undo the increment when the enqueue fails.
Unit test: fill the queue so a SETUP is dropped, then verify the next
SETUP still completes a GET_DESCRIPTOR control transfer.
|
|
|
|
|
|
morse-cedricvandenbergh/fix/ncm-link-state-notify-retry
ncm: retry link-state notification, fix carrier lost on collision
|
|
The self-contained net_ncm fuzz harness #includes ncm_device.c and stubs
the usbd symbols it references rather than linking the device stack.
tud_network_link_state() now calls usbd_defer_func(), so add a matching
no-op stub to keep the harness linking.
|
|
tud_network_link_state() delivered the NETWORK_CONNECTION notification
edge-triggered and fire-once: if a previous notification was still in
flight, notification_xmit() returned early and the notification for the
new link state was never queued. Because link_is_up is committed before
the send, the host could be left reporting a stale carrier state - e.g.
a permanent NO-CARRIER after a link up. The notification state was also
mutated from both the caller and the notify xfer-completion callback
with no serialisation, so on RTOS ports where tud_network_link_state()
runs in a task other than tud_task() the two could race.
Defer the whole link-state update onto the usbd task, so it can no
longer race the completion callback. A collision with an in-flight
notification is resolved by re-arming notification_xmit_state and
letting the existing completion callback drive it forward on the next
xfer completion, rather than adding a separate pending/retry flag.
A link toggle does not change the link speed, so strictly only the
NETWORK_CONNECTION notification needs (re)sending, but reusing the
existing speed-then-connection state machine keeps the fix on a single,
already-serialised code path.
Closes #3760
|
|
audio: fix inverted FIFO-size guard in EP-IN flow control
|
