| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2021-09-23 | Merge pull request #1100 from kasjer/kasjer/da1469b_dk_usb-fix-button-config | Ha Thach | |
| da14695_dk_usb: Fix button configuration | |||
| 2021-09-23 | da14695_dk_usb: Fix button configuration | Jerzy Kasenberg | |
| Unlike da1469x_dk_pro, K1 pin (6) is connected to VCC when active. This adds required pull down and reverses active logic state. | |||
| 2021-09-23 | Merge pull request #1099 from kasjer/kasjer/da1469x_dk_pro-fix-pin-pullup | Ha Thach | |
| da1469x_dk_pro: Fix button setup | |||
| 2021-09-23 | da1469x_dk_pro: Fix button setup | Jerzy Kasenberg | |
| Button on board has 1k resistor to ground when pressed. When not pressed pin 6 is floating. This forces MCU pull-up for this pin for correct behavior. | |||
| 2021-09-23 | Merge pull request #1093 from szymonh/master | Ha Thach | |
| Enforced buffer boundaries for hid devices | |||
| 2021-09-18 | Merge pull request #1094 from kasjer/kasjer/da146xx-vbus-handling | Ha Thach | |
| dcd_da146xx: Add VBUS handling | |||
| 2021-09-17 | Merge pull request #1086 from kkitayam/impl_close_all_for_khci | Ha Thach | |
| Implement dcd_edpt_close_all() and fix dcd_edpt_clear_stall() for frdm_kl25z | |||
| 2021-09-17 | da1469x_dk_xxx: Add VBUS handling | Jerzy Kasenberg | |
| Two BSPs with DA146xx MCUs are now adopted to VBUS handling changed introduced to dcd_da146xx driver. da14695_dk_usb as bus-powered devices informs driver that VBUS is present at startup. da1469x-dk-pro has VBUS change interrupt handler that informs driver about VBUS changes. | |||
| 2021-09-17 | dcd_da146xx: Add VBUS handling | Jerzy Kasenberg | |
| DA146xx are Bluetooth devices that may be battery powered and when not connected to USB host there is no need for USB peripheral to be running. This change allows to enable USB peripheral when VBUS is present otherwise USB is down reducing power consumption. tud_vsub_changed() function must be called whenever VBUS change was detected. For bus-powered devices this function should be called at startup since VBUS must be present while device is working. | |||
| 2021-09-17 | minor clean up | hathach | |
| 2021-09-17 | use correct resume detection for kl25z | hathach | |
| 2021-09-17 | minor update to dcd khci | hathach | |
| 2021-09-15 | Fix stall interrupt handling | kkitayam | |
| 2021-09-15 | Add J1-19 pin setting as a button | kkitayam | |
| 2021-09-15 | Change default LED state to off | kkitayam | |
| 2021-09-15 | merge master and minor clean up | hathach | |
| 2021-09-15 | Merge branch 'master' of github.com:hathach/tinyusb into ↵ | hathach | |
| kkitayam-impl_close_all_for_khci | |||
| 2021-09-15 | Merge pull request #1062 from HiFiPhile/fifo_dcd_transdimension | Ha Thach | |
| Improvements for dcd_transdimension | |||
| 2021-09-14 | Reset EP flags on close. | MasterPhi | |
| 2021-09-14 | Fix warning. | MasterPhi | |
| 2021-09-14 | Merge pull request #1087 from HiFiPhile/nuc_wkp | Ha Thach | |
| NUC126: fix remote_wakeup | |||
| 2021-09-13 | Enforced buffer boundaries for hid devices | szymonh | |
| 2021-09-13 | Update supported.rst | Ha Thach | |
| 2021-09-13 | Merge pull request #1092 from szymonh/master | Ha Thach | |
| Add support for Nucleo F412ZG | |||
| 2021-09-13 | Merge pull request #1091 from hathach/esp32sx-compliance | Ha Thach | |
| Esp32sx compliance | |||
| 2021-09-13 | Add support for Nucleo F412ZG | szymonh | |
| 2021-09-13 | esp32sx implement dcd_remote_wakeup(), fully compliance to chapter9 test suite | hathach | |
| 2021-09-13 | implement dcd_edpt_close_all(), pass chapter9 test suite (without remote wakeup) | hathach | |
| 2021-09-13 | Merge pull request #1090 from szymonh/master | Ha Thach | |
| Prevent buffer overflow in bth_device.c | |||
| 2021-09-13 | Add size check to tud_bt_hci_cmd_cb call in bth_device.c | szymonh | |
| 2021-09-13 | clean up | hathach | |
| 2021-09-13 | clear PID along with clear stall | hathach | |
| 2021-09-13 | Merge branch 'nuc_wkp' of https://github.com/HiFiPhile/tinyusb into ↵ | hathach | |
| HiFiPhile-nuc_wkp | |||
| 2021-09-12 | Prevent buffer overflow in bth_device.c | szymonh | |
| 2021-09-13 | refactor nxp TDI dcd_edpt_xfer_fifo | hathach | |
| 2021-09-12 | Merge branch 'fifo_dcd_transdimension' of https://github.com/HiFiPhile/tinyusb | hathach | |
| 2021-09-12 | Merge pull request #1089 from hathach/imxrt-compliance | Ha Thach | |
| Imxrt compliance | |||
| 2021-09-11 | nxp tdi: implement dcd edpt close all | hathach | |
| 2021-09-11 | nxp tdi: fix error td prevent further transfer | hathach | |
| 2021-09-10 | reset PID to DATA0 on clear_stall. | MasterPhi | |
| 2021-09-10 | Fix remote_wakeup | MasterPhi | |
| 2021-09-10 | Shorter expr. | MasterPhi | |
| 2021-09-10 | Fix dcd_edpt_clear_stall to reset data toggle | kkitayam | |
| 2021-09-10 | Remove heap memory area | kkitayam | |
| 2021-09-09 | dcd_edpt_xfer_fifo: use qtd_init if restriction not met. | Mengsk | |
| 2021-09-09 | nxp tdi: enhance qhd using DCD_ATTR_ENDPOINT_MAX | hathach | |
| 2021-09-09 | nxp tdi implement remote wakeup | hathach | |
| enhance bus reset, unplugged, suspend, resume detection | |||
| 2021-09-09 | remove connected check for DCD_EVENT_UNPLUGGED since previous bus reset can ↵ | hathach | |
| clear this implement unplugged detection for trans dimension dcd | |||
| 2021-09-09 | add other speed descriptor callback ↵ | hathach | |
| tud_descriptor_other_speed_configuration_cb() example implement tud_descriptor_device_qualifier_cb() and tud_descriptor_other_speed_configuration_cb() on high speed device to fully compliant to usbcv | |||
| 2021-09-09 | Fix stall handling | kkitayam | |
