| Age | Commit message (Collapse) | Author |
|---|
|
Pure cleanup, no behavior change:
- Extract the EP0 control-transfer state into a named pipe0_state_t
typedef instead of an anonymous nested struct, and access it through
a local pipe0_state_t* in the functions that touch it repeatedly.
- Group the pipe0 fields so the two bools sit together and the larger
tusb_control_request_t deferred_setup is last.
- Reword the deferral comments: "coalesced" -> "combined".
Note: separating the edpt0_xfer DATA_IN/DATA_OUT case (dispatch on
state instead of dir_in) was attempted and reverted — it breaks ADI
MUSB enumeration. usbd can arm the opposite-direction status while
pipe0 is still in a DATA state, and only dir-dispatch routes that
correctly; a comment on the combined case records this.
Verified: HIL pass on ek_tm4c123gxl and max32666fthr (13/13 each).
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
pyserial's posix write() raises SerialTimeoutException after partial
progress with the byte count lost, so the retry loop re-sent from the
same offset and could duplicate bytes on the wire — surfacing as bogus
data-mismatch failures that look like device firmware bugs.
write_timeout is already a total per-call deadline, so the loop added
duplication risk without extending the budget: write once and treat a
timeout as fatal. Default bumped 2 -> 10 s to keep the old overall
bound; HIL_SERIAL_WRITE_DEADLINE removed.
The per-character CLI loops keep their existing pacing (the 2 ms sleep
between single-byte writes already spaces them on the wire); no
unbounded ser.flush()/tcdrain is added.
Review follow-up for #3643 (hil_test.py l.257/264 findings).
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
The actual-STALL path (no deferred SETUP) forced EP0 to IDLE but left
rxrdy_consumed set if the aborted transfer had parked RXRDY via NAK flow
control (e.g. a rejected OUT-data request in DATA_OUT). A subsequent
SETUP IRQ would then hit the parked-gate early return and be ignored,
relying on SentStall/SetupEnd to clear the flag first. Clear it here
so recovery never depends on that ordering.
Addresses Copilot review on #3699.
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
dcd_edpt_stall(EP0 OUT) discarded the deferred SETUP and armed
SendStall. A deferred SETUP can only exist once the old transfer's
status stage was seen on the wire, so the request usbd is rejecting
(class callback failing at CONTROL_STAGE_DATA) already succeeded
host-side and the hardware already ACKed the next SETUP - the STALL
would land on that innocent request, which then fails host-side
without any tud callback ever seeing it. Skip the stall and replay
the deferred SETUP; the rejected transfer needs no wire-level stall
since it is already over.
Review follow-up for #3643 (dcd_musb.c l.860 finding).
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
The deferral path drains the SETUP but leaves RxPktRdy set, and the
SETUP's IRQ latches after the ISR's clear-on-read intr_tx read - so a
second process_ep0 pass (same ISR, via the intr_tx re-read merge) is
guaranteed and misreads the leftovers: count0==0 fires a spurious
DATA OUT completion, the replay's RXRDYC write turns the second pass
into a phantom csrl==0 DATA IN completion, and a zero-length replay
re-enters the deferral case on a drained FIFO (count0 assert or
garbage saved as a SETUP). The registers cannot expose the staleness:
RxPktRdy and count0 read unchanged until ServicedRxPktRdy is written.
Track it in software: rxrdy_consumed means "RxPktRdy is set in hw but
its packet was already consumed". Set wherever a drained packet's
RXRDY is intentionally left set (OUT/zero-length flow-control parks,
every DATA OUT drain awaiting the next arm, the deferral path);
cleared at every RXRDYC write site (edpt0_xfer arms, dcd_set_address,
STALLED/SETEND recovery, bus reset). The RXRDY block returns early
while parked. Replayed IN requests skip the RXRDYC in
pipe0_start_setup and keep the packet parked until the
edpt0_xfer(DATA IN) arm acks it (before loading the shared FIFO), so
the stale pass sees RXRDY+parked instead of csrl==0. The normal IDLE
path is unchanged - master never re-entered these windows because the
single SETUP edge was always consumed by the pass that parked it; the
deferral is what introduced a pending second pass.
Review follow-up for #3643 (dcd_musb.c l.516 finding).
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
STATUS_OUT_PENDING conflated "edpt0_xfer(STATUS OUT) called, awaiting
confirm IRQ" with "confirm IRQ seen, awaiting edpt0_xfer". The
deferral path completed the status and replayed the saved SETUP from
the ISR in both flavors; in the IRQ-first one, usbd's still-
outstanding edpt0_xfer(STATUS OUT) for the old transfer (queued via
status_stage_xact) then landed in the replayed transfer's state and
corrupted it: NULL pipe0.buf armed plus RXRDYC, so the host's next
DATA OUT drained through a NULL pointer. usbd processes EP0
XFER_COMPLETE events unconditionally, so nothing downstream defuses
it.
Split the state into STATUS_OUT_PENDING_XFER / _IRQ. The deferral
completes and replays only in PENDING_XFER (old transfer already
retired); in PENDING_IRQ it only holds the SETUP and the usbd-driven
edpt0_xfer fires the completion and replays. The DATA_IN deferral now
synthesizes PENDING_IRQ (its remain==0 invariant asserted: a SETUP
before DataEnd raises SetupEnd instead), which also makes the old
deferred-promotion in the csrl==0 DATA_IN case unreachable - dropped.
Assert the drain buffer before the DATA OUT FIFO read as a cheap
backstop for this corruption class.
Review follow-up for #3643 (dcd_musb.c l.503 finding).
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
MUSBMHDRC 21.1.5 requires the EP0 service routine to check SentStall
and SetupEnd first; the early DATAEND return ran before both, and
SentStall is most likely to fire exactly while DataEnd may still read
back set (auto-STALL after DataEnd, 21.1.7), which would skip the
recovery. The guard also moves below the RXRDY block so a coalesced
DATAEND|RXRDY read cannot swallow a SETUP on cores where the
CPU-set-only DataEnd bit reads back 1; the comment documents the
vendor-dependent read-back.
Review follow-up for #3643 (dcd_musb.c l.445 finding).
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
The goto jumped into the csrl==0 completion switch with RXRDY still
set, making its "When CSRL0 is zero" guard comment untrue on that
path. Handle each deferral state in a self-contained switch instead;
the csrl==0 switch is now only reached with csrl==0 and its comment
is truthful again. Behavior unchanged.
Review follow-up for #3643 (dcd_musb.c l.523 finding).
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
The pre-existing comment explaining why the OUT branch does not ack
RxPktRdy was dropped when the SETUP handling moved into
pipe0_start_setup(). It is load-bearing: acking before edpt0_xfer()
arms the drain buffer would let the host send data with nowhere to
put it. Restore it with the databook-deviation rationale so the
branches don't get "unified" later.
Review follow-up for #3643 (dcd_musb.c l.116 finding).
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
The 8-byte EP0 SETUP drain (count0 assert + two FIFO word reads via a
union) was duplicated verbatim between the IDLE case and the deferral
case; a future fix applied to one copy but not the other would only
show up on the rare deferred-race path. Share one helper. count0 is
now read inside the only remaining user (DATA OUT drain).
Review follow-up for #3643 (dcd_musb.c l.507 finding).
Co-Authored-By: Claude Fable 5 <[email protected]>
|
|
|
|
ci(claude-review): run auto review on Opus (claude-opus-4-8)
|
|
The review action currently runs on the default Sonnet 4.6. On PR #3643
(musb EP0 race) it posted "No issues found" while an Opus pass on the
same diff surfaced substantive questions (ISR-boundary RXRDY lifetime,
regression scope of the DATA-state split). Pin the reviewer to
claude-opus-4-8 for higher-signal reviews; subagents keep their cheaper
default models.
Co-Authored-By: Claude Opus 4.8 <[email protected]>
|
|
# Conflicts:
# test/hil/hil_test.py
|
|
ci(claude-review): raise --max-turns 20 -> 50
|
|
|
|
The Claude Code Review action runs /code-review:code-review with a hard
--max-turns cap. On large PRs (e.g. #3636 "add stm32c5 support", 29 files
/ +1689), the agent exhausts 20 turns exploring the diff before it can
produce and post its review, so the SDK returns an error and the
claude-review check fails red with:
Reached maximum number of turns (20)
Raise the cap to 50 so port-sized PRs complete and post their review.
Cost scales with tokens, not the cap: a finished review pays the same
whether the ceiling is 25 or 50 — the cap only bites when the agent
would otherwise be force-stopped mid-run.
Co-Authored-By: Claude Opus 4.8 <[email protected]>
|
|
# Conflicts:
# README.rst
|
|
Replace the ✔/⚠/✖ status symbols in the Supported CPUs table and its
legend with ✅ (Supported), 🟡 (Partial support) and ❌ (Not supported by
hardware) for clearer at-a-glance scanning.
|
|
split-IN NAK storm (#3677)
Fix stm32f723disco host HIL: UART RX starvation + DWC2 split bulk NAK/XactErr handling (#3677)
stm32f7 BSP — UART RX starvation
- The host console USART shared interrupt priority with the USB OTG ISR, so a long
OTG interrupt could starve RXNE and drop received bytes. Raise the USART RX IRQ
above OTG_FS/OTG_HS in both the bare-metal and FreeRTOS init paths, guarded by
#ifdef UART_ID so boards without a UART console keep the default OTG priority.
dwc2 host — split NAK/XactErr handling
- Slave mode: a persistently-NAKing split bulk/control IN poll re-armed the
start-split immediately, storming the ISR and starving task context. Throttle by
disabling the channel and re-arming on the resulting halt (no frame deferral).
- Buffer-DMA mode: a pure split bulk-OUT NAK was unhandled, leaving the channel
halted and stalling the transfer — the dominant cause of CDC echo truncation.
Handle it by rewinding the buffer pointers and retrying the start-split
(Programming Guide v4.20a 5.1.4.2).
- Buffer-DMA mode: a split bulk-OUT XactErr was retried immediately, exhausting
HCD_XFER_ERROR_MAX before the transient cleared. Throttle via channel_disable +
re-arm to give the hub TT a recovery gap, mirroring slave mode.
- All three are scoped to split transfers (hcsplt.split_en); non-split NAK/XactErr
keep the core-handled / immediate-retry behavior. The OUT XactErr throttle also
excludes periodic split, where channel_disable() is a no-op and would wedge the
channel. The nak_disabled flag is generalized to retry_disabled and honors
xfer->closing so an endpoint close during a throttled retry tears down cleanly.
Verified on stm32f723disco HIL (slave + CFG_TUH_DWC2_DMA_ENABLE): host/cdc_msc_hid,
msc_file_explorer, and device_info all pass on both variants; DMA CDC echo went
from ~15-25% raw failure to 10/10 clean.
|
|
* test/hil: replace build.flags_on with named variant schema
Boards declare build variants as `variant: [{name, flags}]` instead of
`build.flags_on`. The variant `name` is the build dir (cmake-build-<name>) and
the HIL report row; `flags` is the raw CFLAGS string (-D...=1) injected via
CFLAGS_CLI. No `variant` => a single build named after the board.
- build.py: --build-name <name> (dir) + --cflag=<token> (raw CFLAGS, repeatable,
=form survives the matrix's shell word-splitting); drop -f1/CFLAGS wrapping.
- hil_ci_set_matrix.py: emit one build arg per variant.
- hil_test.py: iterate variants; report row + build dir = variant name.
- hil_ci.sh: copy all cmake-build-<board>* dirs for -b runs.
- get_deps.py: accept (ignore) --build-name/--cflag from matrix args.
- tinyusb.json: migrate all 6 flags_on boards to variant.
* board_test: park CI build with busy spin instead of wfe
|
|
hil: park boards with idle board_test instead of erasing flash
|
|
HIL: add stm32u083nucleo and post test report as PR comment
|
|
host/cdc: use local control buffer
|
|
Teardown: instead of flashing device/board_test (a USB-less blink loop that
keeps the MCU busy-looping), erase the first flash sector (vector table) so the
board faults to idle after its tests — no USB, lower power, faster. Per-flasher
erase_<name>: openocd/openocd_adi `flash erase_sector 0 0 0`; stlink `--erase
0`; jlink erases the sector at the flash origin read from the ELF (pure-Python,
new elf_flash_origin); esptool `erase_region 0x0 0x4000`; lm4flash writes a 4 KB
all-0xFF blank image (lm4flash erases before programming, so the first sector
ends up blank). device/board_test flash remains a fallback for flashers with no
erase_ function. The teardown is no longer a report column (it's cleanup).
Report: cdc_msc_throughput and msc_file_explorer[_freertos] now return a compact
read/write speed shown in their report cell instead of the pass tick (e.g.
"C 652k/422k M 1.1M/783k", "rd 1.2MB/s"). test_example returns an optional
metric; render_matrix shows it verbatim. Firmware lookup factored into
find_firmware (reused by the erase teardown).
Verified on the rig (stm32f723disco, jlink): erase disables the board in 0.8 s
and it disappears from the bus; the throughput cell shows live speeds.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Neutral white circle for skipped, giving a ✅/❌/⚪ pass/fail/skip set.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Colored emoji render green/red in the GitHub PR comment, far more visible than
the monochrome ✔/✖ dingbats. Skip stays ➖.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
metrics.md (write_combine_markdown) is also used as the PR size comment when
there is no base-metrics baseline; use h2 for its title too so the sticky
comment heading is consistent (and not oversized) in that fallback case.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
The Size Difference Report and HIL comments rendered their titles at h1, which
is oversized inside a PR comment. Use h2 for both titles (with subsections
demoted to h3 to keep the hierarchy), and rename the HIL comment from
"HIL test results" to "Hardware-in-the-loop (HIL) Test Report" for consistency.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
hil-hfp-iar runs hil_test.py on hfp.json built with IAR on its own rig. Upload
its report as the hil-report-hfp-iar artifact and add the job to the hil-report
combine job's needs, so the sticky comment shows a third table for the IAR rig
alongside tinyusb.json and hfp.json (gcc). The combine gate now runs if either
HIL job produced results.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
The report sidecar lives in a persistent dir (it survives the CI workspace
clean so accumulation works across run attempts). A full run is "fresh" and
must not merge prior state, but previously fresh only avoided *loading* the
json at merge time — if a fresh run crashed before writing the report, the
stale json/md from an earlier run lingered and a retry (fresh=False) could
merge it, or the always() upload could post it. Delete hil_report.json/.md at
the start of a fresh run so prior results can never leak.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
hil_test.py persists results in a hil_report.json sidecar and regenerates
hil_report.md from it. A full run starts fresh; a re-run (--skip-board / -bt,
i.e. the .skip file) merges into the existing report so already-passed
boards/tests are preserved while only re-run cells update. The report dir is
configurable via HIL_REPORT_DIR.
build.yml: each HIL rig writes the report to a workspace-sibling dir that
survives the per-attempt workspace clean, and uploads it as an artifact. A new
hil-report job merges the rigs' reports into one sticky PR comment (marocchino)
with one table per rig.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Per review (HiFiPhile): Ninja Multi-Config is needed for IAR, otherwise the
optimization level can't be lowered to none for debug. Revert gen_presets.py
back to Ninja Multi-Config (keeping only the cmake-build-<board> binaryDir
change), and instead teach hil_test.py to locate <ex>.elf whether it sits
directly in the example dir (single-config) or under a per-config subdir like
RelWithDebInfo/ (multi-config).
Verified: stm32u083nucleo passes 13/13 remote HIL with a multi-config preset
build (rsync preserves the RelWithDebInfo/ subdir; the resolver finds it).
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
hil_test.py now writes hil_report.md and prints it to stdout: rows are
boards, columns are tests (bare example names), cells are pass/fail/skip.
test_example returns a per-test status, test_board collects a board x test
grid (one row per flags-on variant), and main() renders an aligned table.
A missing binary counts as skipped. hil_ci.sh copies the report back from
the remote after a run; hil_report.md is gitignored.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
With core.autocrlf=true, *.sh files were checked out / restored with CRLF
line endings, which breaks bash ($'\r': command not found; set: pipefail:
invalid option). Pin *.sh to eol=lf so shell scripts stay LF in the working
tree regardless of autocrlf.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
|
|
|
|
Add stm32u083nucleo to the active boards in tinyusb.json, flashed via the
stlink flasher (onboard ST-Link + STM32CubeProgrammer); ci's openocd build
has no STM32U0 flash driver. STM32_Programmer_CLI lives in ~/bin on ci,
which the remote `bash -s` shell in hil_ci.sh did not have on PATH, so add
$HOME/bin to its PATH export (matching the GHA runner .path). Verified
remote: 13/13 device tests pass on ci.lan.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Change the default configure preset binaryDir from build/<board> to
cmake-build-<board> (the dir name HIL expects) and switch the generator
from Ninja Multi-Config to single-config Ninja. Multi-Config nests
binaries under a RelWithDebInfo/ subdir, which hil_test.py does not look
in; single-config emits device/<ex>/<ex>.elf so preset-built firmware is
directly consumable by `hil_test.py -B examples`.
Regenerated BoardPresets.json (also picks up the tracked ch32v103c_bluepill
board that was missing from presets).
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Previously stm32u0 had no board_get_unique_id(), so it fell back to the
weak default in hw/bsp/board.c and every board reported the placeholder
USB serial 0123456789ABCDEF. HIL identifies boards by USB serial, so a
non-unique serial collides on a multi-board rig. Read the 96-bit unique
ID from UID_BASE, mirroring stm32u5. Verified on stm32u083nucleo: now
enumerates as 300044000D5036394E373620.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Add --comment so the auto-review is actually posted on the PR.
|
|
|
|
* add ek_tm4c123gxl to the hil pool, flashing with lm4flash
|
|
* ci: carry metrics baseline forward on no-code-change pushes
The code-metrics job is gated on code_changed and only uploads the
metrics-tinyusb artifact on push, so a workflow/docs-only push to master (e.g.
removing an unrelated workflow) leaves the latest master Build run without a
baseline. PRs download the baseline from the latest master run, so the size
comparison then finds nothing and silently falls back to absolute sizes.
Add a small metrics-carry-forward job that, on a non-code-change push, downloads
the previous metrics-tinyusb artifact and re-publishes it, so the latest run
always carries a usable baseline. Carry-forward runs re-upload too, so the
baseline chains across consecutive no-code pushes (bounded by artifact retention).
|
|
This personal automation now lives in the hathach/hathach repo alongside the
other personal project-sync workflows; it has no place in the tinyusb library.
Co-authored-by: Claude Opus 4.8 (1M context) <[email protected]>
|
|
dwc2 postfixes
|
|
add device specific issues
|
|
Cast DOEPDMA0 through uintptr_t and use sizeof(tusb_control_request_t)
instead of the magic constant 8, matching project convention. Add a
reference to Programming Guide v4.20a 9.1.2.1 for the DOEPDMAn-8 rule.
Addresses Copilot review comment; no functional change.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
|
|
|
