| Age | Commit message (Collapse) | Author |
|---|
|
Add native USB-MIDI 2.0 Device class driver to TinyUSB. Implements the
USB-MIDI 2.0 specification with both Alt Setting 0 (MIDI 1.0 fallback)
and Alt Setting 1 (UMP native) descriptor support.
Driver features:
- UMP (Universal MIDI Packet) read/write with atomic message framing
- Protocol negotiation: Endpoint Discovery, Config Request/Notify,
Function Block Discovery (embedded in driver)
- Group Terminal Block descriptor via GET_DESCRIPTOR
- Alt Setting switch handler with endpoint re-arm
- Static allocation, no dynamic memory, ISR-safe
Build system:
- Register midi2d_* in usbd.c driver table
- Add TUD_MIDI2_DESCRIPTOR macros to usbd.h
- Add config defaults (CFG_TUD_MIDI2_*) to tusb_option.h
- Add midi2_ump_word_count() to midi.h (shared by Device and Host)
- Add midi2_device.c/h to family.cmake and CMakeLists.txt
- Add midi2_device.h include to tusb.h
All changes guarded by #if CFG_TUD_MIDI2 (default 0). Zero impact on
existing drivers and examples.
Tested: Raspberry Pi Pico (RP2040), Linux ALSA, Windows MIDI Services
|
|
hcd/dwc2: fix txfifo full check
|
|
NCM: support for SetEthernetPacketFilter and SetNTBInputSize request
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
nrf5x: request HFCLK in USB_EVT_READY to fix post-SoftDevice deadlock
|
|
USB_EVT_DETECTED runs hfclk_enable() which, when SoftDevice is not yet
enabled, starts HFXO via direct CLOCK register access. After
sd_softdevice_enable() takes over CLOCK, HFXO is physically off again
and SD's HFCLK reference count is 0.
If USB_EVT_READY is fired post-SD (e.g. on nRF52 via Bluefruit's
usb_softdevice_post_enable() when the pre-SD nrfx_power READY callback
didn't get to run before nrfx_power was uninited), the wait loop
'while (!hfclk_running()) {}' calls sd_clock_hfclk_is_running() which
returns false forever -> deadlock that blocks both USB enumeration and
any further app code on the calling thread.
Call hfclk_enable() right before the wait so HFCLK is requested in
whichever context (SD or direct) is current. hfclk_enable() is
idempotent.
Reproduces reliably with bleuart on Feather nRF52840 Express flashed
via JLink: chip wedges in sd_clock_hfclk_is_running SVC, no USB
enumeration, no BLE advertising. With the fix, USB enumerates and BLE
advertises as expected.
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
midi host: document drain requirement of RX FIFO
|
|
midi-host-rx-bufsize-default-and-docs
|
|
Even if CFG_TUH_MIDI_RX_BUFSIZE=100*TUH_EPSIZE_BULK_MAX, calling tuh_midi_stream_read without a loop can return only one 4-byte packet and preventing subsequent transfer.
Signed-off-by: Zixun LI <[email protected]>
|
|
Co-authored-by: Copilot <[email protected]>
Signed-off-by: Zixun LI <[email protected]>
|
|
Co-authored-by: Copilot <[email protected]>
Signed-off-by: Zixun LI <[email protected]>
|
|
Co-authored-by: Copilot Autofix powered by AI <[email protected]>
|
|
Refactor USB control transfer handling into `usbd.c`
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
|
|
|
|
hathach/copilot/upgrade-net-lwip-webserver-descriptors
net: replace CFG_TUD_NET_ENDPOINT_SIZE with actual descriptor-based ep size
|
|
|
|
|
|
|
|
endpoint state handling methods and accesses
|
|
|
|
|
|
ensure board_uart_write return -1 on default
|
|
`_usbd_dev` structure and remove `usbd_control_reset`
|
|
Co-authored-by: Copilot <[email protected]>
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
|
|
Signed-off-by: HiFiPHile <[email protected]>
|
|
According to NCM standard 7.2.7, the device should tell the host its maximum size of NTB. Implement SetNtbInputSize according to it.
Without this commit, some OS may failed to enumerate the NCM device (e.g., IOS 26).
Signed-off-by: Elwin Huang <[email protected]>
|
|
Signed-off-by: Zixun LI <[email protected]>
|
|
Co-authored-by: Copilot <[email protected]>
Signed-off-by: Zixun LI <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
run my HIL on gcc build
|
|
fix zero wLength request in control request
|
|
|
|
|
|
|
|
|
|
AGENTS.md cleanup, add hil and code-size skills, harden hil_ci.sh
|
|
`git worktree add <path> <branch>` fails if <branch> is already checked out
elsewhere (main repo, another worktree). --detach checks out the ref at a
detached HEAD instead of claiming the branch, making the script work
regardless of what is currently checked out.
Co-Authored-By: Claude Opus 4.7 (1M context) <[email protected]>
|
|
- run() now catches subprocess.TimeoutExpired (only triggered by `cmake --build`'s
timeout=600) and returns CompletedProcess(rc=124) so the caller falls through to
error reporting and worktree cleanup instead of crashing with a traceback.
- code-size SKILL.md: document the actual default filter (per-side absolute
<checkout>/src/ path, not the old `tinyusb/src` substring) and adjust the
reporting guidance to match what the report rows actually contain.
Co-Authored-By: Claude Opus 4.7 (1M context) <[email protected]>
|
|
|
