| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Invoke unmounted state on configuration reset
|
|
|
|
|
|
|
|
|
|
add BOARD_UPPERCASE for board detection
|
|
family_configure_device/host/dual_example()
|
|
|
|
|
|
temporarily disable codespell
|
|
|
|
|
|
IAR generates warning Pe111 'statement is unreachable'. In a couple of
cases, replace return statements with TU_ATTR_FALLTHROUGH; because some
compilers apparently can't figure out that the return statements are
unreachable but do whinge about an imagined fall-through without them!
|
|
up coming release
|
|
|
|
- remove "-Wno-stringop-overflow -Wno-array-bounds"
- skip -Wconversion for gcc 9 and prior
- suppress_tinyusb_warnings only when building with gcc 9 and below
|
|
|
|
* gcc 9.2.1 has some spurious -Wconversion warnings
* cmake 3.18 and above require set_target_properties to be added from the target directory (so added it to all examples)
* fixed a few warnings in a couple of examples
|
|
|
|
since HS interrupt endpoint can be up to 1024, 8-bit is not enough.
affected APIs are:
- tud_hid_n_report() / tud_hid_report()
- tud_hid_report_complete_cb()
|
|
|
|
|
|
- BOARD_DEVICE/HOST_RHPORT_NUM to BOARD_TUD/H_RHPORT
- BOARD_DEVICE/HOST_RHPORT_SPEED to BOARD_TUD/H_MAX_SPEED
|
|
|
|
|
|
|
|
tud_descriptor_other_speed_configuration_cb()
example implement tud_descriptor_device_qualifier_cb() and
tud_descriptor_other_speed_configuration_cb() on high speed device to
fully compliant to usbcv
|
|
|
|
|
|
|
|
|
|
add caplock detection for hid_composite
|
|
Signed-off-by: MasterPhi <[email protected]>
|
|
|
|
- Examples should be CMake buildable from their own subdirectory; such a build will error out based on
matching .skip.MCU_xxx or a mismatched .only.MCU_
- It should be possible to build from a higher level and use .skip.MCU_ and .only.MCU_ to filter which
examples get built
- The intention is for the CMakeLists.txts in the examples to be non family specific and without MCU based IFs. I have
started this work, but am not really sure the state of the esp32 stuff; in any case the plan is to have
everything encapsulated in the FAMILY/family.cmake
- pico_examples now just includes examples/device/CMakeLists.txt and examples/host/CMakeLists.txt directly, as they
also build correctly when included from there.
Note that .skip.MCU_ for esp32 in the directories it wasn't previously avaiable has not been added, as the .skip is common to the regular Makefile builds also. It isn't clear whether these examples should build for esp32, but if not .skip should be added.
|
|
- add tud_hid_n_interface_protocol()
- rename tud_hid_n_boot_mode() to tud_hid_n_get_protocol()
- rename tud_hid_boot_mode_cb() to tud_hid_set_protocol_cb()
- add HID_PROTOCOL_BOOT/REPORT to avoid magic number 0,1
- rename HID_PROTOCOL_NONE/KEYBOARD/MOUSE to HID_ITF_PROTOCOL_ to avoid
confusion
|
|
|
|
also try to update ci
|
|
- also use boot2_generic_03h for now for itsy bitsy and qt rp2040
- change default flash target for rp2040 to flash-pyocd
|
|
- move target_link_libraries() to family.cmake
- enable pico_bootsel_via_double_reset
|
|
following API signature is changed:
- tud_hid_descriptor_report_cb()
- tud_hid_get_report_cb()
- tud_hid_set_report_cb()
- tud_hid_boot_mode_cb()
- tud_hid_set_idle_cb()
|
|
|
|
update hid composite to make use of tud_hid_report_complete_cb() for
sending reports when possible.
|
|
- Add gamepad to hid_composite example. Though it needs a bit of extra
work but it will come later as separated PR.
|
|
|
|
both no OS and freeRTOS
|
|
- PICO_RP2040_USB_DEVICE_ENUMERATION_FIX=1
- target linke pico_fix_rp2040_usb_device_enumeration
|
|
|
|
|
