| Age | Commit message (Collapse) | Author |
|---|
|
Nine examples/host/*/only.txt gate on family:samd21, but 2a8811ebb merged the
samd2x and saml2x BSPs into hw/bsp/samd2x_l2x. skip_example takes `family:` from
the directory name, so since that rename every one of these examples has been
skipped on every board of the family, under make as well as cmake - although
hw/bsp/samd2x_l2x/family.cmake wires src/portable/microchip/samd/hcd_samd.c.
107 host firmware images were being compiled nowhere.
The merged family is wider than the old samd21 one, so three boards need an
explicit skip rather than the rename alone:
atsaml21_xpro, saml22_feather, sensorwatch_m0 - not samd21, so hcd_samd.c is
not compiled for them (previous commit); SAML22 has no host controller at all
curiosity_nano - SAMD21 with 16 KB RAM; msc_file_explorer_freertos overflows it
by 3688 bytes (ram 122.51%). Only that one example; the other eight fit.
Verified across the whole family: cmake 11 boards x 9/9 examples + curiosity_nano
8/9, three boards skipped, 0 failures; make 98 OK / 0 failed (was 98/9 before).
Device examples on saml21 and saml22 are unaffected.
|
|
Documentation tooling:
- Add the `build-doc` skill and `tools/build_doc.py` wrapper for local
Sphinx builds (clean / -W / open).
- Enable Markdown (MyST) in conf.py and auto-collect
examples/{device,host,dual}/*/README.md into a 3-level Examples nav
(Examples > Device/Host/Dual > example), noting each page's source
location and normalizing headings to a single H1.
- Remove the stale `.claude/commands/build-doc.md`; point the AGENTS.md
Documentation section at the skill.
Example docs:
- Add a README.md for every device/host/dual example: what it does, USB
interface table, notable tusb_config.h settings, generic CMake + Make
build steps, and how to try it.
- Fold each *_freertos variant into its base README, noting the FreeRTOS
source path and any RTOS-specific behavior.
Generated docs/examples/ output is git-ignored. Builds clean with
`sphinx-build -W`.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Signed-off-by: HiFiPHile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
|
|
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: Zixun LI <[email protected]>
|
|
Signed-off-by: Zhihong Chen <[email protected]>
|
|
|
|
- Added `rw61x` family support.
- Added `frdm_rw612` board support.
- Update `get_deps.py` to include mcux-sdk for RW61x.
- Add ci_hs_rw61x include to ChipIdea HS driver and enable host examples.
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
|
|
Signed-off-by: Mengsk <[email protected]>
|
|
enable host example build for samd21/d51
|
|
|
|
|
|
|
|
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
change tuh_midi_rx/tx_cb() to have xferred_bytes
rename tuh_midi_get_num_rx/tx_cables() to tuh_midi_get_rx/tx_cable_count()
use default empty callback instead of weak null to be compatible with keil compiler
|
|
|
|
than 1 midi per device.
|
|
to parse/extract this information if needed
rename tuh_midi_configure() to mounted() for consistency
|
|
- rename midi_stream_t to midi_driver_stream_t and move to midi.h (common for device and host)
|
|
xfer_cb as well as ep read()
- de-dup tuh_midi_get_num_rx/tx_cables
- add tuh_midi_read_available()
|
|
- comment out tuh_descriptor_device_cb/tuh_desc_configuration_cb since it is unrelated to this PR
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
