summaryrefslogtreecommitdiff
path: root/hw/bsp
AgeCommit message (Collapse)Author
2020-10-05D5035-01 bsp: fix paths, default to hw rev 1 (automated build)Jean Gressmann
2020-10-05Adds files for the open source D5035-01 hardwareJean Gressmann
The board's files are here: https://github.com/RudolphRiedel/USB_CAN-FD
2020-09-06replacing hcd_pipe_xfer by usbh_edpt_xferhathach
2020-09-04update dochathach
2020-09-03fix vector assignhathach
2020-09-03rename tuh_isr/hcd_isr to tuh_int_handler/hcd_int_handlerhathach
2020-09-03revert to use __USE_LPCOPENhathach
properly init fpu on LPC M4
2020-09-02ohci work, tested with lpc1769hathach
2020-09-02fix ci buildhathach
2020-09-02revert to use float-abihathach
define __USE_CMSIS instead of __USE_LPCOPEN will have startup enable FPU on startup properly. Although it is only relevant to lpx43/40 series, change all to __USE_CMSIS for consistency
2020-09-01add more logging to host stackhathach
tested host with lpc4357, don't use fpu with lpc m4 since it seems to cause hardfault (stack does not make use of fpu anyway).
2020-09-01clean uphathach
2020-09-01Merge branch 'master' into update-hosthathach
2020-08-27add itsybitsy nrf52840 board supporthathach
2020-08-22add OPT_MCU_SAMD11hathach
skip ci build for example that need more ROM/RAM could fit into SAMD11
2020-08-21add support for SAMD11 devices / add samd11_xplained boardKatherine Temkin
2020-08-21fix samg55 ci buildhathach
2020-07-23fix samd21 race condition with setup packethathach
reproduced with Adafruit_TinyUSB_ArduinoCore port commit 11d669b4d2a40eb2fc5e51b2a9707a6de9d42363 and SAMD BSP 1.6.1
2020-07-19Merge pull request #464 from hathach/improve-highspeedHa Thach
Better support highspeed mode
2020-07-16update link speed detection for nuc505hathach
2020-07-14add BSP for Great Scott Gadgets' LUNA boards (SAMD21)Kate Temkin
2020-07-08change REDUCE_SPEED=0/1 to explicitly SPEED=high/fullhathach
update readme, boards.md to add link to new stm boards
2020-07-03Add stm32l4r5nucleo. USB and UARTwork.Uwe Bonnes
USB runs from LSE stabilized MSI48 LPUART on PORTG needs VDDIO2 enabled.
2020-07-03stlinkv3mini: Only OTG_HS has connector.Uwe Bonnes
2020-07-03stm32h745disco: HAL_PWREx_EnableUSBVoltageDetector() is needed for hot replug.Uwe Bonnes
2020-07-03stm32h745disco: Only OTG_FS is available. Does not enumerate on replug yet.Uwe Bonnes
2020-07-03STM32/OTG_HS: Allow OTG_HS port to run at FS speed.Uwe Bonnes
Add "REDUCE_SPEED=1" to the compile options.
2020-07-02correct HSE_VALUE in hal_confhathach
- although it is define in CFLAGS, it is worth to correct to be consistent with other build - extract set_speed()
2020-07-02change default port some stm bsphathach
- f769disco default port is highspeed port1 - remove PORT0 on stlink since the board only populated HS connector
2020-07-01Merge branch 'add-stm-hs' of github.com:hathach/tinyusb into add-stm-hshathach
2020-07-01Add bsp for stlinkv3mini.Uwe Bonnes
2020-07-01added uart for h743hathach
2020-07-01Merge branch 'master' into add-stm-hshathach
2020-07-01Merge pull request #439 from UweBonnes/add-stm-hsHa Thach
Add stm hs
2020-07-01added DA14695 DK USB bsphathach
2020-07-01rename filehathach
2020-06-30more clean uphathach
2020-06-30revert rhport config in nxp mcushathach
2020-06-30stm32f723disco: USB HS enumerates.Uwe Bonnes
2020-06-30Add Stm32F7xxdisco board support filesUwe Bonnes
Status with examples/device/cdc_msc: - make BOARD=stm32f723disco => OK - make BOARD=stm32f723disco PORT=1 => No Reaction - make BOARD=stm32f746disco => OK - make BOARD=stm32f746disco PORT=1 => Hangs during enumeration - make BOARD=stm32f769disco => Hangs during enumeration
2020-06-30stm32h743nucleo: Enable Log via STLINK-VCP.Uwe Bonnes
2020-06-30Merge branch 'master' into add-stm-hshathach
2020-06-30Merge pull request #427 from kasjer/kasjer/add-da1469x-supportHa Thach
Support for DA1469x MCU from Dialog Semiconductor
2020-06-29add kaluga fileshathach
2020-06-29added esp32s2 kaluga bsphathach
2020-06-29Add board support for Dialog DA1469x-dk-proJerzy Kasenberg
This adds source files that allow to run TinyUSB stack on DA1469x-dk-pro board. Source files .c .S and .ld are taken from Apache Mynewt repository. Those files were stripped to allow starting board without Mynewt os.
2020-06-16fix stm32h743 priority with freeRTOShathach
2020-06-15clean up, update other example confighathach
2020-06-14revert CFG_TUSB_RHPORT0_MODE to previous wayhathach
2020-06-01adding speed detect on bus resethathach
generated by cgit v1.3.1 (git 2.54.0) at 2026-08-29 19:20:19 +0000