tinyusb.git - Unnamed repository; edit this file 'description' to name the repository.

Age	Commit message (Collapse)	Author
2020-05-31	fixed EP0 size to 64 since LS is not supported in device mode	hathach
	- set turn-around and report actual speed in Enum Done - add dcd_event_bus_reset() helper to report speed
2020-05-31	able to detect as hs	hathach

2020-05-27	try to get synopsys work with OTG HS + external PHY	hathach

2020-05-26	multiple port support for global otg base	hathach

2020-05-26	suporting multiple port (OTG FS + HS) for stm32	hathach

2020-05-15	Allow EP0 to use xfer sizes larger than one packet	Jan Dümpelmann

2020-05-15	Interrupt time improvements	Jan Dümpelmann

2020-05-08	Synopsys OUT EP improvements:	Jan Dümpelmann
	- Use register based XFRSIZ to determine transfer complete (xfer->queued_len and xfer->short_packet were deleted) - Pop out as many RxFIFO data entries as available within a IRQ call - less application interruption due to XFRC calls
2020-05-04	clean up	Jan Dümpelmann
	renaming function and variables changing indent size
2020-04-29	Changed switch into if statements	Jan Dümpelmann

2020-04-29	Redesign of Synopsys device transmission	Jan Dümpelmann
	Changes: - checking if tx buffer empty interrupt is masked - process more than one packet in isr - mask tx buffer empty just after all bytes were written - use of transmit_fifo_packet instead of transmit_packet
2020-04-27	added comment for hw clearing TXFE	hathach

2020-04-27	TXFE is read only bit	hathach

2020-04-26	turn off TX FIFO Empty for EPIN if all bytes are written	hathach
	fix dcd synopsys issue with usbnet #289
2020-04-24	synopsys: Reduce interrupt time for IN ZLP	Jerzy Kasenberg
	For IN endpoints output FIFO is filled in interrupt, therefor before endpoint is enabled, DIEPTSIZ is set with correct size of packet. Then endpoint is enabled and FIFO empty interrupt is enabled. This works fine except for the ZLP. Enabling FIFO empty interrupt results in interrupt handler being called all the time because there is nothing to put in the FIFO. Eventually it ends when IN token is received and empty packed is transmitted out. This change does not enable FIFO empty interrupt for ZLP reducing CPU load.
2020-04-22	Added support for STM32F1 Connectivity Line MCU	Jan Dümpelmann
	STM32F105 and STM32F107 are using the Synopsys IP
2020-04-18	also add wakeup event	hathach

2020-04-18	implement disconnection detection for stm32 synopsys	hathach
	- disconnection is OTG INT session end bit - add USE_SOF to disable 1ms interrupt on mcu which isn't used now by the stack - add suspend detection
2020-04-17	complete remove dcd_set_config(), fix unit test	hathach

2020-04-17	mass rename tud/dcd_irq_handler to tud/dcd_init_handler	hathach

2020-04-16	stm32 sysnopsys disconnect/connect	hathach

2020-04-08	move irq for stm32 synopsys	hathach

2019-12-21	Merge branch 'master' into port-samg55	hathach

2019-12-11	move VBUS sense out of dcd_synosys to bsp	hathach

2019-11-28	use dcd_edpt0_status_complete() to set address without blocking for ↵	hathach
	samd21/samd51/stm32_fsdev
2019-09-27	add -Wextra for more warnings to example	hathach
	non-stack warning (probably mcu driver) should be suppressed in the board.mk
2019-09-21	dcd_synopsys: Fix off-by-one error in FIFO allocation.	William D. Jones

2019-09-13	This demonstrates that I don't pre-build things before committing them... oops.	Nathan Conrad

2019-09-13	Off-by-one error in Synopsys assertions. (and move some braces to their own ↵	Nathan Conrad
	lines.
2019-09-13	adding stm32l4 support, board test run with stm32l476disco, usb doens't work yet	hathach

2019-09-12	ported stm32f2, added board stm32f207zg nucleo	hathach
	close #127
2019-09-11	stm32f7 work with dcd synopsis	hathach
	close #124
2019-09-09	stm32: Refactor so F4 and H7 use a single Synopsys IP source file.	William D. Jones