| Age | Commit message (Expand) | Author |
|---|
| 2018-12-21 | change to dcd_get_frame_number | hathach |
| 2018-12-19 | fix samd build | hathach |
| 2018-12-17 | add dcd_get_microframe() | hathach |
| 2018-12-14 | rename bit_* helper to tu_bit_*, BIT_* to TU_BIT_* for consistency | hathach |
| 2018-12-12 | rename edpt_dir/number/addr to tu_edpt_* | hathach |
| 2018-12-12 | rename hcd_device_remove to hcd_device_close | hathach |
| 2018-12-07 | rename MODE_HOST_SUPPORTED to TUSB_OPT_HOST_ENABLED | hathach |
| 2018-12-07 | clean up ehci, support only 1 controller | hathach |
| 2018-12-07 | lpc17 ohci failed to execute control transfer !! | hathach |
| 2018-12-07 | enable all warnings | hathach |
| 2018-12-05 | able to build host lpc18xx | hathach |
| 2018-12-05 | update nrf errata | hathach |
| 2018-12-05 | hal clean up | hathach |
| 2018-12-05 | remove dcd_connect/disconnect since there is no usage now | hathach |
| 2018-12-05 | lpc move Chip_USB_Init() out of stack to bsp | hathach |
| 2018-12-05 | renane file | hathach |
| 2018-12-05 | lpc40xx device work, moving Chip_USB_Init out of tinyusb | hathach |
| 2018-12-04 | move pinmux out of dcd into bsp | hathach |
| 2018-12-04 | adding ea4088 quickstart, able to blink | hathach |
| 2018-12-04 | adding lpc40xx support | hathach |
| 2018-12-04 | add mcb1800, blink led ok | hathach |
| 2018-12-04 | rename dcd 18 43 | hathach |
| 2018-12-03 | clean up dcd 43 | hathach |
| 2018-12-03 | dcd lpc43 clean up | hathach |
| 2018-12-03 | use lpcopen for lpc43x, work well | hathach |
| 2018-12-03 | use lpcopen for ea4357, blinky ok | hathach |
| 2018-12-03 | clean up | hathach |
| 2018-12-03 | clean up | hathach |
| 2018-12-03 | migrate lpc17 to lpcopen, usb device work ok | hathach |
| 2018-12-03 | wrap up lpc11u port | hathach |
| 2018-12-03 | clean up dcd lpc11u | hathach |
| 2018-12-03 | dcd lpc11u6x work with cdc + msc | hathach |
| 2018-12-02 | lpc11u use USBSRAM, able to response with 1st request | hathach |
| 2018-12-01 | lp11u able to receive setup packet | hathach |
| 2018-11-30 | lpc13xx build ok (not work) with lpcopen | hathach |
| 2018-11-30 | rename cont | hathach |
| 2018-11-30 | more rename | hathach |
| 2018-11-30 | rename | hathach |
| 2018-11-30 | clean up | hathach |
| 2018-11-30 | rename OPT_MCU_LPC13UXX to OPT_MCU_LPC13XX | hathach |
| 2018-11-29 | move nvic prio in hal/dcd to bsp for portability | hathach |
| 2018-11-29 | added & tested lpc17xx freertos device example | hathach |
| 2018-11-29 | lpc17xx add dcd_edpt_stalled | hathach |
| 2018-11-29 | dcd lpc17xx, route control endpoint to EP_FAST | hathach |
| 2018-11-29 | clean up | hathach |
| 2018-11-29 | dcd lpc17xx enable EpIntEn for non-control IN after DMA complete | hathach |
| 2018-11-28 | correct TUD_OPT_HIGH_SPEED | hathach |
| 2018-11-28 | more dcd lpc17xx clean up | hathach |
| 2018-11-28 | clean up | hathach |
| 2018-11-28 | improve non-control xfer for lpc17xx | hathach |
