| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2020-07-01 | st/synopsys/dcd_synopsys.c: Remove USBC PHY PLL stabilization delay for now | Uwe Bonnes | |
| While the ST code has a 2 ms stabilization delay for the USBC PHY PLL, running without this delay showed no problem for at leat 10 USB un/replug cycles. Observe for problems! | |||
| 2020-06-30 | stm32f723disco: USB HS enumerates. | Uwe Bonnes | |
| 2020-06-30 | dcd_synopsys: Handle HS and FS IP in one device | Uwe Bonnes | |
| FIXME: Allow run-time selection to allow to handle both HS and FS with one file F746 HS port enumerates with error config 1 interface 2 altsetting 0 bulk endpoint 0x3 has invalid maxpacket 64 | |||
| 2020-06-30 | Merge branch 'master' into add-stm-hs | hathach | |
| 2020-06-29 | Merge pull request #399 from duempel/redesign_synopsys_receive | Ha Thach | |
| Improvements to Synopsys EP OUT | |||
| 2020-06-29 | Add author name to dcd_synopsys.c | Jan Dümpelmann | |
| 2020-06-26 | Remove EP0 remaining bytes manipulation | Jan Dümpelmann | |
| Renaming edpt_xact to edpt_schedule_packets | |||
| 2020-06-25 | dcd_samd: Provide implementation for OPT_MCU_SAME5X | Jeff Epler | |
| 2020-06-24 | added OPT_MCU_SAME5X option | hathach | |
| 2020-06-18 | Add transaction (edpt_xact) as sub transfer | Jan Dümpelmann | |
| A transfer can have one or multiple transactions. Usually only EP0 splits one xfer into multiple xact. | |||
| 2020-06-18 | Disable SOF in dcd_stm32_fsdev | Mengsk | |
| Signed-off-by: Mengsk <[email protected]> | |||
| 2020-06-17 | Fix IAR warnings. | Mengsk | |
| Pa039 : use of address of unaligned structure member. Pe188: enumerated type mixed with another type. | |||
| 2020-06-16 | fix hs port1 build with net endpoint | hathach | |
| 2020-06-16 | fix stm32h743 priority with freeRTOS | hathach | |
| 2020-06-15 | Enhance EP FIFO allocation for both Fullspeed and Highspeed | hathach | |
| - Update shared RX FIFO calculation with FS/HS - IN FIFO EP - Interrupt -> use EPSize - Bulk/ISO -> use max(EPSize, remaining-fifo / non-opened-EPIN) | |||
| 2020-06-14 | Fix wrong comment for IAD checks. | Reinhard Panhuber | |
| 2020-06-14 | cherry pick PR399 commit : Interrupt time improvements | Jan Dümpelmann | |
| 2020-06-14 | overwrite setup packet | hathach | |
| 2020-06-14 | improve usbd log for control transfer | hathach | |
| 2020-06-14 | revert CFG_TUSB_RHPORT0_MODE to previous way | hathach | |
| 2020-06-14 | Fix alignment. | Reinhard Panhuber | |
| 2020-06-14 | Fix alignment. | Reinhard Panhuber | |
| 2020-06-13 | Fix too strict checks on subclass and interface of iad descriptor. | Reinhard Panhuber | |
| 2020-06-01 | adding speed detect on bus reset | hathach | |
| 2020-06-01 | allow hs ep open with 512 bytes | hathach | |
| 2020-05-31 | fixed EP0 size to 64 since LS is not supported in device mode | hathach | |
| - set turn-around and report actual speed in Enum Done - add dcd_event_bus_reset() helper to report speed | |||
| 2020-05-31 | able to detect as hs | hathach | |
| 2020-05-31 | Merge pull request #413 from kasjer/kasjer/ble-over-usb | Ha Thach | |
| Bluetooth HCI transport over USB | |||
| 2020-05-28 | add get device qualifier descriptor | hathach | |
| 2020-05-28 | Add bt hci device class | Jerzy Kasenberg | |
| Code implements USB transport for bluetooth HCI. | |||
| 2020-05-28 | Add non standard request handling in class | Jerzy Kasenberg | |
| For some reason bluetooth stack implementations send class requests to device instead of interface. To implement HCI interface over USB non device addressed requests for class need to be handled. | |||
| 2020-05-28 | check max_len for vendor and hid | hathach | |
| 2020-05-28 | rename to drv_len to be consistent | hathach | |
| 2020-05-28 | initial transfer failed in open() shouldn't cause the driver open to fail. | hathach | |
| 2020-05-28 | update vendor open() | hathach | |
| 2020-05-28 | update usbtmc open() | hathach | |
| 2020-05-28 | update net open() | hathach | |
| 2020-05-28 | update midi open() | hathach | |
| 2020-05-28 | update hid open() | hathach | |
| 2020-05-28 | improve msc | hathach | |
| 2020-05-28 | change signature for dfu runtime | hathach | |
| 2020-05-27 | changing usbd driver open() return type, add max_len | hathach | |
| only done with cdc and msc, push this interim for feedback first | |||
| 2020-05-27 | try to get synopsys work with OTG HS + external PHY | hathach | |
| 2020-05-26 | random clean up for tdi | hathach | |
| 2020-05-26 | update h743eval with rhport=1 highspeed | hathach | |
| 2020-05-26 | multiple port support for global otg base | hathach | |
| 2020-05-26 | suporting multiple port (OTG FS + HS) for stm32 | hathach | |
| 2020-05-26 | merge CFG_TUSB_RHPORT1_MODE into CFG_TUSB_RHPORT0_MODE | hathach | |
| each port is 1 byte for easy maintenance | |||
| 2020-05-21 | fix nrf hanged (blocking wait) when called within critical section | hathach | |
| 2020-05-20 | fix freeRTOS logic | hathach | |
