| Age | Commit message (Collapse) | Author |
|---|
|
and mimxrt1015
edpt_schedule_packets() advanced xfer->buffer past each armed EP0
chunk, so the OUT-complete handler invalidated the cache at the
ADVANCED pointer: one line past the received data. The CPU then read
stale cached bytes instead of the DMA'd packet, and the misplaced
invalidate discarded a dirty line of whatever variable follows the
buffer - random neighbor corruption on every control-OUT data stage.
Found by usbtest ctrl_out (cases 14/21) on espressif_p4_function_ev
with DMA enabled, the first DWC2 target combining buffer DMA with a
data cache: usbd control state wedged after the first control write
(every later request stalled), and one build layout panicked in the
usbd memcpy with a wild pointer.
Rework the EP0 chunk bookkeeping so xfer->buffer always points at the
un-consumed position: the arm no longer advances it; instead the EP0
re-arm paths advance past each completed (full) chunk, invalidating it
first on the OUT side. The final OUT completion invalidates exactly
the received bytes of its last chunk, taken from DOEPDMA ("incremented
on every AHB transaction", databook 7.1.83 - the same semantics the
SETUP path relies on) before dma_setup_prepare() re-targets it. EP0
chunking state (ep0_pending) is now also dropped on bus reset and on
a new SETUP, so a stale latched completion can no longer re-arm EP0
DMA from dead state. No behavior change for targets without dcache.
While root-causing, the FIFO layout was cross-checked against the
DWC2 databook/programming guide v4.20a: the existing GDFIFOCFG
programming (EPInfoBaseAddr = otg_dfifo_depth - 2*ep_count, one SPRAM
word per endpoint direction for buffer DMA) is conformant and needs
no change; the P4 HS instance's reset GDFIFOCFG (0x03800400) merely
reflects a scatter/gather-sized EP_LOC_CNT of 128 that buffer DMA
does not need.
With the fix in place, enable the usbtest battery on the espressif
fleet: tools/build.py allowlists device/usbtest (a plain IDF component
like board_test/video_capture) and both espressif boards' only-lists
gain device/usbtest. Also re-enable device/usbtest on mimxrt1015_evk:
its skip predated the dcd_ci_hs stale-ACTIVE-overlay fix (already on
this branch), which cured the battery that previously killed the
uPD720201 host controller twice (2026-07-11 ROM fw, 2026-07-13 case 27
on fw 2.0.2.6); rig-validated 30/30 three consecutive runs.
Validated on rig (all 30/30): espressif_p4_function_ev(-DMA) (was
22/30 under DMA), espressif_s3_devkitm(-DMA), stm32f723disco(-DMA),
mimxrt1015_evk; p4/s3 slave-mode unaffected (DMA-only code path);
compile-checked stm32h743nucleo +TUD DMA, stm32f407disco,
stm32l476disco (device ports currently on the dead hub).
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_017TQZrFfU3K4Y198aLsUpBC
|
|
- dcd_edpt_stall flushes the primed buffer (ENDPTFLUSH), but the aborted
transfer's dQH overlay can be left ACTIVE with mid-transfer state; the
next prime after clear-halt then resumes the stale overlay instead of
loading the fresh qtd, so post-halt IN reads return mid-buffer data
(usbtest case 13 'buf[32] = 56 (not 0)', with case 18 failing
downstream of the same corruption in the full battery). qhd_start_xfer
now clears overlay.active alongside overlay.halted before linking the
new qtd.
- test/hil(hfp): drop lpcxpresso43s67's device/usbtest skip - the
historical first-case wedge no longer reproduces on this branch, and
with the overlay fix the board runs 30/30 on its Fresco xHCI host
(previously 28/30 with deterministic case 13/18 failures).
mimxrt1064_evk (imxrt dcache path) 30/30 regression-clean.
- docs(hil skill): document the external hifiphile rig - pool
test/hil/hfp.json, SSH-reachable from htpc/ci with no outbound SSH,
exercised by the CI hil-tinyusb (hfp.json) job; never run HIL against
it during development unless the user explicitly asks.
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_017TQZrFfU3K4Y198aLsUpBC
|
|
# Conflicts:
# .claude/skills/hil/SKILL.md
# test/hil/hil_test.py
|
|
- EP0 OUT: park a back-to-back data-stage packet the DCP accepted before
PID could go NAK and deliver it into the next armed chunk; flow-control
the single-buffer control pipe between chunks (usbtest ctrl_out
corruption); discard a packet parked while an OUT pipe was halted so
BOT reset recovery's fresh CBW read can't receive stale WRITE data
- HS UTMI PHY power-up per the FSP sequence, shared by dcd/hcd: CLKSEL
programmed from the board XTAL (EK-RA8M1 runs 20 MHz; the 24 MHz reset
default never locks) while DIRPD holds the PHY down, then timed release
- hw/bsp(ra8m1_ek): fix U60CK divider macro - BSP_CFG_U60CK_DIV used the
generic USB_CLOCK_DIV_8 encoding (7), which USB60CKDIVCR rejects,
leaving the USBHS link domain at 480 MHz; the USB60-specific
BSP_CLOCKS_USB60_CLOCK_DIV_8 (4) sticks and yields the required 60 MHz
from PLL1P
- support FS-only builds on the high-speed port: gate SYSCFG.HSE on
TUD_OPT_HIGH_SPEED (RHPORT_DEVICE_SPEED=OPT_MODE_FULL_SPEED was a
silent no-op) and always compile both hwfifo access widths - the FIFO
width belongs to the module, not the link speed (FS builds corrupted
odd-length tails: 16-bit access against MBW-32)
- iso activate: reset stale pipe bookkeeping so a BRDY firing before the
class re-arms can't replay a pre-SET_INTERFACE transfer; write PIPEBUF
after PIPESEL selects the pipe (PIPESEL-windowed register)
- clear-halt: re-assert BUF on a still-armed OUT pipe (usbtest case 29)
- bound the D0FIFO ready spin so an undrained double-buffered IN pipe
can't freeze the stack with the IRQ masked
- usbtest example: cap interrupt mps at 64 on RUSB2 high speed (pipes
6-9 have a fixed 64-byte buffer, RA6M5 UM 29.1)
Verified: usbtest 30/30 on ra6m5_ek (HS), ra4m1_ek (FS) and ra8m1_ek
(FS-forced build on the HS port).
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
The no-op activate left a transfer armed before SET_INTERFACE valid in
data.xfer, letting the ISR complete it against the old buffer. Drop the
descriptor and NAK the endpoint (mirrors the nrf5x fix).
Verified: usbtest 30/30 on ch32v103r, nanoch32v203, ch582m_evt.
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
EPSKIP raises a transfer completion, so using it on the stall path let
the class re-arm the endpoint and Active+Stall never actually stalled
(usbtest case 13); write bare Active=0 instead, and retire skipped
transfers on endpoint reopen where the completion is wanted.
Verified: usbtest 30/30 on lpcxpresso11u37.
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
nrf_clock_is_running() was added in nrfx 2.1.0 (MDK 8.30.2), but the
version autodetect puts 2.0.0 (MDK 8.29.0) in the v2 bucket, so
hfclk_running() fails to compile on that nrfx.
Route v2 through nrf_clock_hf_is_running(), which all of 2.x provides.
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Double-buffered iso, EP3 1023-byte packets on V20x/V30x (10-bit
R16_UEP3_T_LEN), CH583 and V103 enabled at 64 B.
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
USBD drops tasks during EasyDMA without the 0x40027C1C latch (anomaly 199);
matches the nrfx reference driver.
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Clear Active before Stall so a queued endpoint actually halts (UM11126
41.8.1); use the sanctioned EPSKIP+wait sequence for stall/reopen/activate.
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
An unpolled full iso-IN pipe keeps FRDY low forever and froze the stack
with IRQs masked; bound the spin and abort the FIFO access.
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Reserve the bank SIZE bucket once, re-enable per altsetting, and scrub the
bank-ready state so a stale armed bank cannot send before the class re-arms.
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Non-buffered per-type source/sink endpoints (bulk/int/iso) with manual RX
arming across altsettings.
Co-Authored-By: Claude Fable 5 <[email protected]>
Claude-Session: https://claude.ai/code/session_01HeF2gZ1M7GWkz6Av4BpKPg
|
|
Signed-off-by: Javid Khan <[email protected]>
|
|
feat(midi2): derive function blocks from the GTB descriptor
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Fix usbd empty builtin driver warning
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Fix USBTMC status byte interrupt buffer
|
|
bound ndp16 wLength against received ntb in recv_validate_datagram
|
|
Queue the USB488 READ_STATUS_BYTE interrupt notification through tud_usbtmc_transmit_notification_data so it uses the class notification endpoint buffer for the asynchronous transfer.
Fixes #2928
Generated-by: OpenAI Codex
Signed-off-by: aineoae86-sys <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Use usbd_edpt_claim() before queuing USBTMC notification data so the interrupt endpoint is reserved through the normal endpoint ownership path. Release the claim if the notification payload cannot be copied before the transfer is queued.
Fixes #2735
Generated-by: OpenAI Codex
Signed-off-by: aineoae86-sys <[email protected]>
|
|
Generated-by: OpenAI Codex
Signed-off-by: aineoae86-sys <[email protected]>
|
|
max3421: prevent USB host hang at startup
|
|
cdc_host: fix undeclared 'idx' when only LINE_CONTROL_ON_ENUM is defined
|
|
* license: use SPDX identifiers for src/ headers
Replace the full ~20-line MIT license boilerplate on every src/ file with a
two-line SPDX tag (SPDX-FileCopyrightText + SPDX-License-Identifier), following
the REUSE convention used by CircuitPython and the Linux kernel. Removes ~3500
lines of duplicated boilerplate.
|
|
stabilization timing
|
|
On some boards the MAX3421E doesn't report its oscillator ready after a
soft reset (CHIPRES), so hcd_init() waits on USBIRQ_OSCOK forever and the
host hangs at startup before any USB device can be used. Bound the wait so
it proceeds after a timeout; it is a no-op where OSCOK arrives normally.
Needed on the Adafruit Feather ESP32 V2 (classic ESP32) + USB Host
FeatherWing, which otherwise hangs on essentially every cold boot.
Relates to adafruit/circuitpython#10053.
|
|
Release:
- Bump version to 0.21.0 and regenerate tusb_option.h, library.json,
repository.yml, sonar-project.properties, boards.rst, dependencies.rst
- Add 0.21.0 release notes and split the changelog into per-release files
under docs/info/changelog/ (date out of title, driver/class groups as
sub-headings, DCD & HCD section after Device/Host stacks)
Contributors:
- Credit each release's PR authors in a Contributors section
- Drop the curated contributors page; add MAINTAINERS.rst
Docs:
- Update Code of Conduct to Contributor Covenant 3.0 (keep it in the repo,
remove it from the built docs)
- Sidebar: add a home entry, rename the group to "Documentation", move
Changelog into it, add a GitHub Sponsor button, merge external links,
rename FAQ; hide the inline toctree on the landing page
- Add the make-release skill and update the AGENTS.md release process
Co-Authored-By: Claude Opus 4.8 (1M context) <[email protected]>
|
|
Function Block Info (direction, group span, name) is derived from the GTB
descriptor as the single source of truth, so a device can expose multiple
Group Terminal Blocks with independent directions. Adds Function Block Name
notifications (tud_midi2_fb_name_cb) and an opt-in callback to answer UMP
Stream messages from the application (tud_midi2_stream_msg_cb). Ref #3571
|
|
|
|
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
typec/stm32: fix UCPD sink bugs affecting compatibility with newer PD sources
|
|
When a Low-Speed device is connected through the internal FS PHY,
the effective PHY clock is 6MHz (HCFG_FSLS_PHYCLK_SEL_6MHZ),
but phy_clock was incorrectly left at 48. This caused HFIR to be
calculated as 47999 (~8ms SOF interval) instead of the correct 5999
(1ms SOF interval), breaking periodic endpoint scheduling.
Fixes: LS mouse only receiving first HID report on OTG_HS + FS PHY
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
Signed-off-by: HiFiPhile <[email protected]>
|
|
|
|
dcd/stm32_fsdev: workaround CH32 EP0 premature OUT ACK
|
