| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2020-07-16 | add tud_speed_get() | hathach | |
| - define both fs and hs configuration descriptor - rename CFG_TUD_CDC_EPSIZE to CFG_TUD_CDC_EP_BUFSIZE with default size of 64 for FS, and 512 for HS | |||
| 2020-07-10 | Improve comment on CDC tud_cdc_write_available() | Craig Hutchinson | |
| Fixes #460 | |||
| 2020-07-10 | Merge pull request #456 from me-no-dev/esp32-s2-epin-to | Ha Thach | |
| ESP32-S2: Detect EP IN Xfer Timeout | |||
| 2020-07-08 | Merge pull request #447 from hathach/add-stm-hs | Ha Thach | |
| Add support for STM32 OTG HS core | |||
| 2020-07-08 | change REDUCE_SPEED=0/1 to explicitly SPEED=high/full | hathach | |
| update readme, boards.md to add link to new stm boards | |||
| 2020-07-05 | Merge pull request #457 from UweBonnes/add-stm-hs | Ha Thach | |
| Add stm hs | |||
| 2020-07-03 | STM32/OTG_HS: Allow OTG_HS port to run at FS speed. | Uwe Bonnes | |
| Add "REDUCE_SPEED=1" to the compile options. | |||
| 2020-07-03 | update per review | hathach | |
| 2020-07-03 | fix NVIC disable typo | hathach | |
| 2020-07-02 | ESP32-S2: Detect EP IN Xfer Timeout | me-no-dev | |
| In some rare ocasions (bad cable, noise, etc.) data transfer might timeout and hang the endpoint, unless the interrupt flag is cleared. This pull request targets to solve that case. | |||
| 2020-07-02 | correct HSE_VALUE in hal_conf | hathach | |
| - although it is define in CFLAGS, it is worth to correct to be consistent with other build - extract set_speed() | |||
| 2020-07-02 | change default port some stm bsp | hathach | |
| - f769disco default port is highspeed port1 - remove PORT0 on stlink since the board only populated HS connector | |||
| 2020-07-02 | clean up | hathach | |
| 2020-07-01 | Merge branch 'add-stm-hs' of github.com:hathach/tinyusb into add-stm-hs | hathach | |
| 2020-07-01 | st/synopsys/dcd_synopsys.c: Remove USBC PHY PLL stabilization delay for now | Uwe Bonnes | |
| While the ST code has a 2 ms stabilization delay for the USBC PHY PLL, running without this delay showed no problem for at leat 10 USB un/replug cycles. Observe for problems! | |||
| 2020-07-01 | only set turnaround in reset complete | hathach | |
| 2020-07-01 | correctly set turn around according to cpu clock | hathach | |
| help to run with low speed mcu | |||
| 2020-07-01 | Merge branch 'master' into add-stm-hs | hathach | |
| 2020-07-01 | clean up code | hathach | |
| 2020-07-01 | ESP32-S2: Handle the fact that available EP IN FIFOs are less than the ↵ | me-no-dev | |
| number of available EP INs ESP32-S2 has only 5 available endpoint-in FIFOs (including EP0) but 7 available EP IN numbers. This change decouples the fifo number from the endpoint number, providing FIFO numbers until they reach the limit, at which point it will return false and assert an error that too many endpoints were allocated. | |||
| 2020-07-01 | Merge pull request #452 from hathach/fix-dfu-rt | Ha Thach | |
| Fix dfu rt | |||
| 2020-07-01 | fix dfu-rt to response to SET_INTERFACE and DFU_GETSTATUS | hathach | |
| fix #450 | |||
| 2020-06-30 | Clear ep0_pending if rx short packet | Jan Dümpelmann | |
| 2020-06-30 | Fix receiving of short packet data (ep out) | Jan Dümpelmann | |
| 2020-06-30 | stm32f723disco: USB HS enumerates. | Uwe Bonnes | |
| 2020-06-30 | dcd_synopsys: Handle HS and FS IP in one device | Uwe Bonnes | |
| FIXME: Allow run-time selection to allow to handle both HS and FS with one file F746 HS port enumerates with error config 1 interface 2 altsetting 0 bulk endpoint 0x3 has invalid maxpacket 64 | |||
| 2020-06-30 | Merge branch 'master' into add-stm-hs | hathach | |
| 2020-06-30 | Merge pull request #427 from kasjer/kasjer/add-da1469x-support | Ha Thach | |
| Support for DA1469x MCU from Dialog Semiconductor | |||
| 2020-06-29 | Merge pull request #399 from duempel/redesign_synopsys_receive | Ha Thach | |
| Improvements to Synopsys EP OUT | |||
| 2020-06-29 | Add author name to dcd_synopsys.c | Jan Dümpelmann | |
| 2020-06-26 | Remove EP0 remaining bytes manipulation | Jan Dümpelmann | |
| Renaming edpt_xact to edpt_schedule_packets | |||
| 2020-06-25 | dcd_samd: Provide implementation for OPT_MCU_SAME5X | Jeff Epler | |
| 2020-06-24 | added OPT_MCU_SAME5X option | hathach | |
| 2020-06-20 | Call tud_cdc_tx_cb right after flush to keep tx fifo full | Gavin Li | |
| 2020-06-20 | Merge branch 'master' into uac2 | Reinhard Panhuber | |
| Conflicts: src/device/usbd.c | |||
| 2020-06-20 | Get update from tinyusb. | Reinhard Panhuber | |
| 2020-06-18 | Add transaction (edpt_xact) as sub transfer | Jan Dümpelmann | |
| A transfer can have one or multiple transactions. Usually only EP0 splits one xfer into multiple xact. | |||
| 2020-06-18 | Disable SOF in dcd_stm32_fsdev | Mengsk | |
| Signed-off-by: Mengsk <[email protected]> | |||
| 2020-06-18 | Add tx callback to cdc device | Gavin Li | |
| Useful for continuous transmission of data, which is difficult currently because there is no notification of tx completion. | |||
| 2020-06-17 | Fix IAR warnings. | Mengsk | |
| Pa039 : use of address of unaligned structure member. Pe188: enumerated type mixed with another type. | |||
| 2020-06-16 | fix hs port1 build with net endpoint | hathach | |
| 2020-06-16 | fix stm32h743 priority with freeRTOS | hathach | |
| 2020-06-15 | Enhance EP FIFO allocation for both Fullspeed and Highspeed | hathach | |
| - Update shared RX FIFO calculation with FS/HS - IN FIFO EP - Interrupt -> use EPSize - Bulk/ISO -> use max(EPSize, remaining-fifo / non-opened-EPIN) | |||
| 2020-06-14 | Fix wrong comment for IAD checks. | Reinhard Panhuber | |
| 2020-06-14 | cherry pick PR399 commit : Interrupt time improvements | Jan Dümpelmann | |
| 2020-06-14 | overwrite setup packet | hathach | |
| 2020-06-14 | improve usbd log for control transfer | hathach | |
| 2020-06-14 | revert CFG_TUSB_RHPORT0_MODE to previous way | hathach | |
| 2020-06-14 | Fix alignment. | Reinhard Panhuber | |
| 2020-06-14 | Fix alignment. | Reinhard Panhuber | |
