| Age | Commit message (Collapse) | Author |
|---|
|
rename and moving bsp ea4357
|
|
fix some compiler warnings
|
|
|
|
refractor list_find_previous_item & list_remove_qhd to act on ehci_link_t* instead of ehci_qhd_t*
fully support 1ms, 2ms, 4ms, 8ms for period list (each list has a dummy queue head)
- change period list structure
limit the maximum polling interval to 256 ms
add max_loop static MAX number of iteration for list_find_previous_item
add test for close 256ms polling interrupt
|
|
implementing freeRTOS integration
change get_period_frame_list from using lst_idx to hostid (fix bug)
adding polling interval supported for interrupt: 1ms, 2ms, 4ms, 8ms
- add interval_ms to get_period_head function
- add bInterval to qhd_init
- add support for sub-frame (less than 8 micro frames) interval
- add bunch of test for interrupt different intervals
|
|
|
|
(callback isr)
and using OSAL for task-base demo
- fix ehci error with XFER_COMPLETE callback to usbh_isr, TD need to be freed & unlink before invoking
callback
- fix bug in usbh.c set device state to CONFIGURED right after SET_CONFIGURE control xfer
|
|
bangding I2C on PB_0 PB_1)
add back port reset after get 8 bytes of device descriptor
|
|
rename tusb_bus_event_t to tusb_event_t
add test_mouse_init and more stuff for hidh mouse
move delay after port reset to only for speed detection
prioritize port change interrupt over xfer interrupt
- in case of unplugged, current connect change & xfer error both set
- xfer error only break to debugger if not because of unplugged
fix bug: set dev addr0 state to UNPLUG after close its control pipe in enumeration process
|
|
start to add support for host hid mouse
|
|
add hack delay 100 ms after a port reset (huge) for correct speed detection
|
|
refractor test code
|
|
configure before open class driver
|
|
implement keyboard app code
- forcefully place keyboard_report in RAM section 3
change used bit in qtd from reserved in buffer[1] to alternate link
add code for fake ehci controller runs on period interrupt
change signature of tusbh_hid_keyboard_get_report
- tusb_keyboard_report_t* to uint8_t*
implement period (interrupt) complete isr processing
|
|
refractor hidh_open_subtask & hidh_keyboard_open
add ATTR_PACKED_STRUCT(x)
- TODO remove ugly pre_pack & post pack
|
|
|
|
- bulk/int/iso pipe can only be closed as part of unmount/safe remove process
add test for interrupt_close
|
|
|
|
|
|
- rename usbh_device_info_pool to usbh_devices
- create a struct for control pipe in usbh_device_info_t
|
|
|
|
transfer of control pipe
- fix bug with hcd_port_reset
+ remove regs->portsc_bit.port_enable in the wait loop as device unplugged can cause this to always fails
- correct the timeout for hcd_controll_stop/reset 16 uframes ~ 2 ms
- potentially fix bugs device unplugged when new address is not assigned
|
|
add test for usbh_isr error invoke
fix bug if device unplugged before is set to new address
- clean up & close control addr0 in usbh_device_unplugged_isr
|
|
change singature of call_isr as well
|
|
- rename TUSB_DEVICE_STATE_READY to TUSB_DEVICE_STATE_CONFIGURED
- move device_state to core/tusb_types.h
- remove usbh_device_hcd_data_cleaned_up_cb, hcd now set the state directly
|
|
|
|
|
|
|
|
|
|
- only acknowledge interrupt that we check
|
|
|
|
|
|
(previously mark as removing).
|
|
- add hal_debugger_is_attached & hal_debugger_breakpoint
- assert will suspend (place breakpoint) if the condition is failed and debugger is attached. Otherwise, a message to uart is printed
- fix get control qhd function when dev_addr is not zero (shifted 1)
- fix wrong logic for unsupported class
|
|
- add tests for pipe_close (while TDs are active)
- add tests for device unplugged
add tesst & implement the async_advance_isr to clean up "REMOVING" queue head
- add helper find previous qhd
- add remove qhd from async list
- add is_removing field for async advance isr to clean up
add pipe close for control pipe & bulk pipe (with tests)
add helper get qhd from pipe_handle
|
|
|
|
adding some code for async_advance_isr
add test for async_advance_isr
|
|
close control pipe when unplugged
|
|
rename class_install_subtask to class_open_subtask
add class_close for unmount
adding code for usbh_device_unplugged_isr & invoke it in hcd_isr
|
|
- fix init_qhd for address 0 (clear queue head --> ehci controller halted)
- fix bug in usbh_init missing address0 for semaphore create
TUSB_CFG_DEBUG == 3: --> ATTR_ALWAYS_INLINE is null --> allow gcc to export "normal inline" function
|
|
add osal_queue_send in usbh_device_plugged
add macro for placing breakpoint macros
fix ehci init:
- regs->cmd or (add run_stop)
- enable port power in portsc
add tusb_task_runner in main loop
|
|
clean up
|
|
- void usbh_device_plugged_isr(uint8_t hostid, tusb_speed_t speed);
- void usbh_device_unplugged_isr(uint8_t hostid);
implement port_connect_status_isr
|
|
fix binary.h compiler specific
add hal_init code to reset & set usbmode --> able to get USB ISR
remove const qualifier from return function of
- get_operational_register
- get_period_frame_list
- get_async_head
- get_period_head
- get_control_qhd
add stub for
- hcd_port_connect_status
- hcd_port_speed
|
|
modify test to check control pipe semaphore created with usbh_init
|
|
- interrupt source identifying
- for async list process
refractor control_xfer to use insert_qtd_to_qhd
- add test for control xfer interrupt processing
- add code for faking ehci controller async list scheduling & processing
- add prototype for void usbh_isr(pipe_handle_t pipe_hdl, uint8_t class_code);
|
|
|
|
|
|
|
|
|
