From c0ecf8b50fe68a56b28bed98ecbfc6b236a848ef Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 26 May 2023 14:56:22 +0700 Subject: move set TOP to family_support.cmake --- hw/bsp/family_support.cmake | 3 +++ hw/bsp/imxrt/family.cmake | 3 --- hw/bsp/lpc18/family.cmake | 2 -- hw/bsp/lpc55/family.cmake | 2 -- hw/bsp/mcx/family.cmake | 2 -- hw/bsp/nrf/family.cmake | 2 -- hw/bsp/rp2040/family.cmake | 4 ++-- 7 files changed, 5 insertions(+), 13 deletions(-) diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index 5bd9a6d75..68a21bc7d 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -2,6 +2,9 @@ include_guard() include(CMakePrintHelpers) +# TOP is path to root directory +set(TOP "${CMAKE_CURRENT_LIST_DIR}/../..") + # Default to gcc if (NOT DEFINED TOOLCHAIN) set(TOOLCHAIN gcc) diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index f9818cde6..a681b0419 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -4,9 +4,6 @@ if (NOT BOARD) message(FATAL_ERROR "BOARD not specified") endif () -# TOP is path to root directory -set(TOP "${CMAKE_CURRENT_LIST_DIR}/../../..") - # toolchain set up set(CMAKE_SYSTEM_PROCESSOR cortex-m7 CACHE INTERNAL "System Processor") set(CMAKE_TOOLCHAIN_FILE ${TOP}/tools/cmake/toolchain/arm_${TOOLCHAIN}.cmake) diff --git a/hw/bsp/lpc18/family.cmake b/hw/bsp/lpc18/family.cmake index c47839a5c..698120077 100644 --- a/hw/bsp/lpc18/family.cmake +++ b/hw/bsp/lpc18/family.cmake @@ -4,8 +4,6 @@ if (NOT BOARD) message(FATAL_ERROR "BOARD not specified") endif () -# TOP is path to root directory -set(TOP "${CMAKE_CURRENT_LIST_DIR}/../../..") set(SDK_DIR ${TOP}/hw/mcu/nxp/lpcopen/lpc18xx/lpc_chip_18xx) # toolchain set up diff --git a/hw/bsp/lpc55/family.cmake b/hw/bsp/lpc55/family.cmake index d6ce0b781..1b9c1a655 100644 --- a/hw/bsp/lpc55/family.cmake +++ b/hw/bsp/lpc55/family.cmake @@ -4,8 +4,6 @@ if (NOT BOARD) message(FATAL_ERROR "BOARD not specified") endif () -# TOP is path to root directory -set(TOP "${CMAKE_CURRENT_LIST_DIR}/../../..") set(SDK_DIR ${TOP}/hw/mcu/nxp/mcux-sdk) set(CMSIS_DIR ${TOP}/lib/CMSIS_5) diff --git a/hw/bsp/mcx/family.cmake b/hw/bsp/mcx/family.cmake index abca7c90e..1719320e6 100644 --- a/hw/bsp/mcx/family.cmake +++ b/hw/bsp/mcx/family.cmake @@ -4,8 +4,6 @@ if (NOT BOARD) message(FATAL_ERROR "BOARD not specified") endif () -# TOP is path to root directory -set(TOP ${CMAKE_CURRENT_LIST_DIR}/../../..) set(SDK_DIR ${TOP}/hw/mcu/nxp/mcux-sdk) set(CMSIS_DIR ${TOP}/lib/CMSIS_5) diff --git a/hw/bsp/nrf/family.cmake b/hw/bsp/nrf/family.cmake index 59d4a7947..68b19b33b 100644 --- a/hw/bsp/nrf/family.cmake +++ b/hw/bsp/nrf/family.cmake @@ -4,8 +4,6 @@ if (NOT BOARD) message(FATAL_ERROR "BOARD not specified") endif () -# TOP is path to root directory -set(TOP "${CMAKE_CURRENT_LIST_DIR}/../../..") set(NRFX_DIR ${TOP}/hw/mcu/nordic/nrfx) set(CMSIS_DIR ${TOP}/lib/CMSIS_5) diff --git a/hw/bsp/rp2040/family.cmake b/hw/bsp/rp2040/family.cmake index 17f206c77..28637e3ee 100644 --- a/hw/bsp/rp2040/family.cmake +++ b/hw/bsp/rp2040/family.cmake @@ -16,8 +16,8 @@ if (NOT TARGET _rp2040_family_inclusion_marker) include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) # TOP is absolute path to root directory of TinyUSB git repo - set(TOP "${CMAKE_CURRENT_LIST_DIR}/../../..") - get_filename_component(TOP "${TOP}" REALPATH) + #set(TOP "${CMAKE_CURRENT_LIST_DIR}/../../..") + #get_filename_component(TOP "${TOP}" REALPATH) if (NOT PICO_TINYUSB_PATH) set(PICO_TINYUSB_PATH ${TOP}) -- cgit v1.3.1 From b262164a35e9e305b67cb8d0c2188353db405200 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 26 May 2023 15:16:18 +0700 Subject: fix build with net_lwip_webserver example --- examples/device/CMakeLists.txt | 7 +- examples/device/net_lwip_webserver/CMakeLists.txt | 148 +++++++++++----------- src/CMakeLists.txt | 2 + 3 files changed, 80 insertions(+), 77 deletions(-) diff --git a/examples/device/CMakeLists.txt b/examples/device/CMakeLists.txt index 89cfceeeb..5b077a5e1 100644 --- a/examples/device/CMakeLists.txt +++ b/examples/device/CMakeLists.txt @@ -22,12 +22,7 @@ family_add_subdirectory(hid_generic_inout) family_add_subdirectory(hid_multiple_interface) family_add_subdirectory(midi_test) family_add_subdirectory(msc_dual_lun) - -# FIXME temp skip net_lwip_webserver for imxrt for now -if (NOT ${FAMILY} STREQUAL "imxrt" AND NOT ${FAMILY} STREQUAL "mcx") - family_add_subdirectory(net_lwip_webserver) -endif() - +family_add_subdirectory(net_lwip_webserver) family_add_subdirectory(uac2_headset) family_add_subdirectory(usbtmc) family_add_subdirectory(video_capture) diff --git a/examples/device/net_lwip_webserver/CMakeLists.txt b/examples/device/net_lwip_webserver/CMakeLists.txt index e7338c809..5225f7c42 100644 --- a/examples/device/net_lwip_webserver/CMakeLists.txt +++ b/examples/device/net_lwip_webserver/CMakeLists.txt @@ -1,83 +1,89 @@ cmake_minimum_required(VERSION 3.17) -set(TOP "../../..") -get_filename_component(TOP "${TOP}" REALPATH) +include(${CMAKE_CURRENT_LIST_DIR}/../../../hw/bsp/family_support.cmake) -if (EXISTS ${TOP}/lib/lwip/src) - include(${TOP}/hw/bsp/family_support.cmake) +set(LWIP ${TOP}/lib/lwip) +if (NOT EXISTS ${LWIP}/src) + MESSAGE(WARNING "lib/lwip submodule not found, please run 'python tools/get_deps.py lib/lwip' to fetch it") + return() +endif() - # gets PROJECT name for the example (e.g. -) - family_get_project_name(PROJECT ${CMAKE_CURRENT_LIST_DIR}) +# gets PROJECT name for the example (e.g. -) +family_get_project_name(PROJECT ${CMAKE_CURRENT_LIST_DIR}) - project(${PROJECT} C CXX ASM) +project(${PROJECT} C CXX ASM) - # Checks this example is valid for the family and initializes the project - family_initialize_project(${PROJECT} ${CMAKE_CURRENT_LIST_DIR}) +# Checks this example is valid for the family and initializes the project +family_initialize_project(${PROJECT} ${CMAKE_CURRENT_LIST_DIR}) - add_executable(${PROJECT}) +add_executable(${PROJECT}) - # Example source - target_sources(${PROJECT} PUBLIC - ${CMAKE_CURRENT_SOURCE_DIR}/src/main.c - ${CMAKE_CURRENT_SOURCE_DIR}/src/usb_descriptors.c - ) +# Example source +target_sources(${PROJECT} PUBLIC + ${CMAKE_CURRENT_LIST_DIR}/src/main.c + ${CMAKE_CURRENT_LIST_DIR}/src/usb_descriptors.c + ) - # Example include - target_include_directories(${PROJECT} PUBLIC - ${CMAKE_CURRENT_SOURCE_DIR}/src - ${TOP}/lib/lwip/src/include - ${TOP}/lib/lwip/src/include/ipv4 - ${TOP}/lib/lwip/src/include/lwip/apps - ${TOP}/lib/networking - ) +# Example include +target_include_directories(${PROJECT} PUBLIC + ${CMAKE_CURRENT_LIST_DIR}/src + ${LWIP}/src/include + ${LWIP}/src/include/ipv4 + ${LWIP}/src/include/lwip/apps + ${TOP}/lib/networking + ) - target_sources(${PROJECT} PUBLIC - ${TOP}/lib/lwip/src/core/altcp.c - ${TOP}/lib/lwip/src/core/altcp_alloc.c - ${TOP}/lib/lwip/src/core/altcp_tcp.c - ${TOP}/lib/lwip/src/core/def.c - ${TOP}/lib/lwip/src/core/dns.c - ${TOP}/lib/lwip/src/core/inet_chksum.c - ${TOP}/lib/lwip/src/core/init.c - ${TOP}/lib/lwip/src/core/ip.c - ${TOP}/lib/lwip/src/core/mem.c - ${TOP}/lib/lwip/src/core/memp.c - ${TOP}/lib/lwip/src/core/netif.c - ${TOP}/lib/lwip/src/core/pbuf.c - ${TOP}/lib/lwip/src/core/raw.c - ${TOP}/lib/lwip/src/core/stats.c - ${TOP}/lib/lwip/src/core/sys.c - ${TOP}/lib/lwip/src/core/tcp.c - ${TOP}/lib/lwip/src/core/tcp_in.c - ${TOP}/lib/lwip/src/core/tcp_out.c - ${TOP}/lib/lwip/src/core/timeouts.c - ${TOP}/lib/lwip/src/core/udp.c - ${TOP}/lib/lwip/src/core/ipv4/autoip.c - ${TOP}/lib/lwip/src/core/ipv4/dhcp.c - ${TOP}/lib/lwip/src/core/ipv4/etharp.c - ${TOP}/lib/lwip/src/core/ipv4/icmp.c - ${TOP}/lib/lwip/src/core/ipv4/igmp.c - ${TOP}/lib/lwip/src/core/ipv4/ip4.c - ${TOP}/lib/lwip/src/core/ipv4/ip4_addr.c - ${TOP}/lib/lwip/src/core/ipv4/ip4_frag.c - ${TOP}/lib/lwip/src/netif/ethernet.c - ${TOP}/lib/lwip/src/netif/slipif.c - ${TOP}/lib/lwip/src/apps/http/httpd.c - ${TOP}/lib/lwip/src/apps/http/fs.c - ${TOP}/lib/networking/dhserver.c - ${TOP}/lib/networking/dnserver.c - ${TOP}/lib/networking/rndis_reports.c - ) +# lib/networking sources +target_sources(${PROJECT} PUBLIC + ${TOP}/lib/networking/dhserver.c + ${TOP}/lib/networking/dnserver.c + ${TOP}/lib/networking/rndis_reports.c + ) - # due to warnings from other net source, we need to prevent error from some of the warnings options - target_compile_options(${PROJECT} PUBLIC - -Wno-error=null-dereference - -Wno-error=conversion - -Wno-error=sign-conversion - -Wno-error=sign-compare - ) +# lwip sources +target_sources(${PROJECT} PUBLIC + ${LWIP}/src/core/altcp.c + ${LWIP}/src/core/altcp_alloc.c + ${LWIP}/src/core/altcp_tcp.c + ${LWIP}/src/core/def.c + ${LWIP}/src/core/dns.c + ${LWIP}/src/core/inet_chksum.c + ${LWIP}/src/core/init.c + ${LWIP}/src/core/ip.c + ${LWIP}/src/core/mem.c + ${LWIP}/src/core/memp.c + ${LWIP}/src/core/netif.c + ${LWIP}/src/core/pbuf.c + ${LWIP}/src/core/raw.c + ${LWIP}/src/core/stats.c + ${LWIP}/src/core/sys.c + ${LWIP}/src/core/tcp.c + ${LWIP}/src/core/tcp_in.c + ${LWIP}/src/core/tcp_out.c + ${LWIP}/src/core/timeouts.c + ${LWIP}/src/core/udp.c + ${LWIP}/src/core/ipv4/autoip.c + ${LWIP}/src/core/ipv4/dhcp.c + ${LWIP}/src/core/ipv4/etharp.c + ${LWIP}/src/core/ipv4/icmp.c + ${LWIP}/src/core/ipv4/igmp.c + ${LWIP}/src/core/ipv4/ip4.c + ${LWIP}/src/core/ipv4/ip4_addr.c + ${LWIP}/src/core/ipv4/ip4_frag.c + ${LWIP}/src/netif/ethernet.c + ${LWIP}/src/netif/slipif.c + ${LWIP}/src/apps/http/httpd.c + ${LWIP}/src/apps/http/fs.c + ) - # Configure compilation flags and libraries for the example... see the corresponding function - # in hw/bsp/FAMILY/family.cmake for details. - family_configure_device_example(${PROJECT}) -endif() +# due to warnings from other net source, we need to prevent error from some of the warnings options +target_compile_options(${PROJECT} PUBLIC + -Wno-error=null-dereference + -Wno-error=conversion + -Wno-error=sign-conversion + -Wno-error=sign-compare + ) + +# Configure compilation flags and libraries for the example... see the corresponding function +# in hw/bsp/FAMILY/family.cmake for details. +family_configure_device_example(${PROJECT}) diff --git a/src/CMakeLists.txt b/src/CMakeLists.txt index 0b99d8919..0d2f0975b 100644 --- a/src/CMakeLists.txt +++ b/src/CMakeLists.txt @@ -34,6 +34,8 @@ function(add_tinyusb TARGET) ) target_include_directories(${TARGET} PUBLIC ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + # TODO for net driver, should be removed/changed + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../lib/networking ) # enable all possible warnings target_compile_options(${TARGET} PUBLIC -- cgit v1.3.1 From 1d857605b79156a10d14aeb837a9e82bbb81e87c Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 26 May 2023 15:25:55 +0700 Subject: use get_deps.py --- .github/workflows/build_aarch64.yml | 2 +- .github/workflows/build_arm.yml | 2 +- .github/workflows/build_iar.yml | 2 +- .github/workflows/build_msp430.yml | 2 +- .github/workflows/build_renesas.yml | 2 +- .github/workflows/build_riscv.yml | 2 +- 6 files changed, 6 insertions(+), 6 deletions(-) diff --git a/.github/workflows/build_aarch64.yml b/.github/workflows/build_aarch64.yml index 77d3778d7..6ac7ad015 100644 --- a/.github/workflows/build_aarch64.yml +++ b/.github/workflows/build_aarch64.yml @@ -70,7 +70,7 @@ jobs: run: echo >> $GITHUB_PATH `echo ~/cache/toolchain/*/bin` - name: Get Dependencies - run: python3 tools/get_family_deps.py ${{ matrix.family }} + run: python3 tools/get_deps.py ${{ matrix.family }} - name: Build run: python3 tools/build_family.py ${{ matrix.family }} diff --git a/.github/workflows/build_arm.yml b/.github/workflows/build_arm.yml index 1db9586af..e3b9a9686 100644 --- a/.github/workflows/build_arm.yml +++ b/.github/workflows/build_arm.yml @@ -77,7 +77,7 @@ jobs: echo >> $GITHUB_ENV PICO_SDK_PATH=~/pico-sdk - name: Get Dependencies - run: python3 tools/get_family_deps.py ${{ matrix.family }} + run: python3 tools/get_deps.py ${{ matrix.family }} - name: Build run: python3 tools/build_family.py ${{ matrix.family }} diff --git a/.github/workflows/build_iar.yml b/.github/workflows/build_iar.yml index 8c3b57e10..3da5ed40f 100644 --- a/.github/workflows/build_iar.yml +++ b/.github/workflows/build_iar.yml @@ -44,7 +44,7 @@ jobs: uses: actions/checkout@v3 - name: Get Dependencies - run: python3 tools/get_family_deps.py ${{ matrix.family }} + run: python3 tools/get_deps.py ${{ matrix.family }} - name: Build run: python3 tools/build_family.py ${{ matrix.family }} CC=iccarm diff --git a/.github/workflows/build_msp430.yml b/.github/workflows/build_msp430.yml index 5424a88d6..c62056940 100644 --- a/.github/workflows/build_msp430.yml +++ b/.github/workflows/build_msp430.yml @@ -68,7 +68,7 @@ jobs: run: echo >> $GITHUB_PATH `echo ~/cache/toolchain/*/bin` - name: Get Dependencies - run: python3 tools/get_family_deps.py ${{ matrix.family }} + run: python3 tools/get_deps.py ${{ matrix.family }} - name: Build run: python3 tools/build_family.py ${{ matrix.family }} diff --git a/.github/workflows/build_renesas.yml b/.github/workflows/build_renesas.yml index 3f0a4b694..66b98a71b 100644 --- a/.github/workflows/build_renesas.yml +++ b/.github/workflows/build_renesas.yml @@ -68,7 +68,7 @@ jobs: run: echo >> $GITHUB_PATH `echo ~/cache/toolchain/*/bin` - name: Get Dependencies - run: python3 tools/get_family_deps.py ${{ matrix.family }} + run: python3 tools/get_deps.py ${{ matrix.family }} - name: Build run: python3 tools/build_family.py ${{ matrix.family }} diff --git a/.github/workflows/build_riscv.yml b/.github/workflows/build_riscv.yml index 8682d655a..8ec549072 100644 --- a/.github/workflows/build_riscv.yml +++ b/.github/workflows/build_riscv.yml @@ -69,7 +69,7 @@ jobs: run: echo >> $GITHUB_PATH `echo ~/cache/toolchain/*/bin` - name: Get Dependencies - run: python3 tools/get_family_deps.py ${{ matrix.family }} + run: python3 tools/get_deps.py ${{ matrix.family }} - name: Build run: python3 tools/build_family.py ${{ matrix.family }} -- cgit v1.3.1 From 05cc342dfa258a2c5e381788009b84445b6e9856 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 26 May 2023 15:45:55 +0700 Subject: update deps, rename kinetis_k32 to k32l --- .github/workflows/build_arm.yml | 2 +- hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.h | 58 ------ hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.mk | 26 --- .../boards/frdm_k32l2a4s/frdm_k32l2a4s.c | 171 ---------------- hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.h | 56 ------ hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.mk | 26 --- .../kinetis_k32/boards/frdm_k32l2b/frdm_k32l2b.c | 140 ------------- .../boards/kuiic/K32L2B31xxxxA_flash.ld | 216 --------------------- hw/bsp/kinetis_k32/boards/kuiic/board.h | 45 ----- hw/bsp/kinetis_k32/boards/kuiic/board.mk | 26 --- hw/bsp/kinetis_k32/boards/kuiic/kuiic.c | 203 ------------------- hw/bsp/kinetis_k32/family.mk | 32 --- hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.h | 58 ++++++ hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.mk | 26 +++ .../boards/frdm_k32l2a4s/frdm_k32l2a4s.c | 171 ++++++++++++++++ hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.h | 56 ++++++ hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.mk | 26 +++ .../kinetis_k32l/boards/frdm_k32l2b/frdm_k32l2b.c | 140 +++++++++++++ .../boards/kuiic/K32L2B31xxxxA_flash.ld | 216 +++++++++++++++++++++ hw/bsp/kinetis_k32l/boards/kuiic/board.h | 45 +++++ hw/bsp/kinetis_k32l/boards/kuiic/board.mk | 26 +++ hw/bsp/kinetis_k32l/boards/kuiic/kuiic.c | 203 +++++++++++++++++++ hw/bsp/kinetis_k32l/family.mk | 32 +++ hw/bsp/saml2x/family.mk | 6 +- tools/get_deps.py | 5 +- 25 files changed, 1006 insertions(+), 1005 deletions(-) delete mode 100644 hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.h delete mode 100644 hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.mk delete mode 100644 hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/frdm_k32l2a4s.c delete mode 100644 hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.h delete mode 100644 hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.mk delete mode 100644 hw/bsp/kinetis_k32/boards/frdm_k32l2b/frdm_k32l2b.c delete mode 100644 hw/bsp/kinetis_k32/boards/kuiic/K32L2B31xxxxA_flash.ld delete mode 100644 hw/bsp/kinetis_k32/boards/kuiic/board.h delete mode 100644 hw/bsp/kinetis_k32/boards/kuiic/board.mk delete mode 100644 hw/bsp/kinetis_k32/boards/kuiic/kuiic.c delete mode 100644 hw/bsp/kinetis_k32/family.mk create mode 100644 hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.h create mode 100644 hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.mk create mode 100644 hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/frdm_k32l2a4s.c create mode 100644 hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.h create mode 100644 hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.mk create mode 100644 hw/bsp/kinetis_k32l/boards/frdm_k32l2b/frdm_k32l2b.c create mode 100644 hw/bsp/kinetis_k32l/boards/kuiic/K32L2B31xxxxA_flash.ld create mode 100644 hw/bsp/kinetis_k32l/boards/kuiic/board.h create mode 100644 hw/bsp/kinetis_k32l/boards/kuiic/board.mk create mode 100644 hw/bsp/kinetis_k32l/boards/kuiic/kuiic.c create mode 100644 hw/bsp/kinetis_k32l/family.mk diff --git a/.github/workflows/build_arm.yml b/.github/workflows/build_arm.yml index e3b9a9686..8fbaba4c6 100644 --- a/.github/workflows/build_arm.yml +++ b/.github/workflows/build_arm.yml @@ -34,7 +34,7 @@ jobs: family: # Alphabetical order - 'broadcom_32bit' - - 'kinetis_k32 kinetis_kl' + - 'kinetis_k32l kinetis_kl' - 'lpc11 lpc13 lpc15 lpc17 lpc18' - 'lpc51 lpc54 lpc55' - 'mm32 msp432e4' diff --git a/hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.h b/hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.h deleted file mode 100644 index b1f38c997..000000000 --- a/hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.h +++ /dev/null @@ -1,58 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - - -#ifndef BOARD_H_ -#define BOARD_H_ - -#include "fsl_device_registers.h" - -// LED -// The Red LED is on PTE29. -// The Green LED is on PTC4. -// The Blue LED is on PTE31. -#define LED_PIN_CLOCK kCLOCK_PortC -#define LED_GPIO GPIOC -#define LED_PORT PORTC -#define LED_PIN 4 -#define LED_STATE_ON 0 - -// SW3 button1 -#define BUTTON_PIN_CLOCK kCLOCK_PortE -#define BUTTON_GPIO GPIOE -#define BUTTON_PORT PORTE -#define BUTTON_PIN 4 -#define BUTTON_STATE_ACTIVE 0 - -// UART -#define UART_PORT LPUART0 -#define UART_PIN_CLOCK kCLOCK_PortB -#define UART_PIN_GPIO GPIOB -#define UART_PIN_PORT PORTB -#define UART_PIN_RX 16u -#define UART_PIN_TX 17u - -#endif /* BOARD_H_ */ diff --git a/hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.mk b/hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.mk deleted file mode 100644 index d96ab58b8..000000000 --- a/hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/board.mk +++ /dev/null @@ -1,26 +0,0 @@ -MCU = K32L2A41A - -CFLAGS += \ - -mcpu=cortex-m0plus \ - -DCPU_K32L2A41VLH1A \ - -# mcu driver cause following warnings -CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls -Wno-error=cast-qual - -# All source paths should be relative to the top level. -LD_FILE = $(MCU_DIR)/gcc/K32L2A41xxxxA_flash.ld - -SRC_C += \ - $(MCU_DIR)/project_template/clock_config.c \ - -# For freeRTOS port source -FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM0 - -# For flash-jlink target -JLINK_DEVICE = K32L2A41xxxxA - -# For flash-pyocd target -PYOCD_TARGET = K32L2A - -# flash using pyocd -flash: flash-pyocd diff --git a/hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/frdm_k32l2a4s.c b/hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/frdm_k32l2a4s.c deleted file mode 100644 index 80830163b..000000000 --- a/hw/bsp/kinetis_k32/boards/frdm_k32l2a4s/frdm_k32l2a4s.c +++ /dev/null @@ -1,171 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2018, hathach (tinyusb.org) - * Copyright (c) 2020, Koji Kitayama - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "bsp/board.h" -#include "board.h" -#include "fsl_gpio.h" -#include "fsl_port.h" -#include "fsl_clock.h" -#include "fsl_lpuart.h" - -#include "clock_config.h" - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void USB0_IRQHandler(void) -{ - tud_int_handler(0); -} - -void board_init(void) -{ - /* Enable port clocks for UART/LED/Button pins */ - CLOCK_EnableClock(UART_PIN_CLOCK); - CLOCK_EnableClock(LED_PIN_CLOCK); - CLOCK_EnableClock(BUTTON_PIN_CLOCK); - - gpio_pin_config_t led_config = { kGPIO_DigitalOutput, 0 }; - GPIO_PinInit(LED_GPIO, LED_PIN, &led_config); - PORT_SetPinMux(LED_PORT, LED_PIN, kPORT_MuxAsGpio); - - gpio_pin_config_t button_config = { kGPIO_DigitalInput, 0 }; - GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); - const port_pin_config_t BUTTON_CFG = { - kPORT_PullUp, - kPORT_FastSlewRate, - kPORT_PassiveFilterDisable, - kPORT_OpenDrainDisable, - kPORT_LowDriveStrength, - kPORT_MuxAsGpio, - kPORT_UnlockRegister - }; - PORT_SetPinConfig(BUTTON_PORT, BUTTON_PIN, &BUTTON_CFG); - - /* - Enable LPUART0 clock and configure port pins. - FIR clock is being used so the USB examples work. - */ - PCC_LPUART0 = 0U; /* Clock must be off to set PCS */ - PCC_LPUART0 = PCC_CLKCFG_PCS( 3U ); /* Select the clock. 1:OSCCLK/Bus Clock, 2:Slow IRC, 3: Fast IRC, 6: System PLL */ - PCC_LPUART0 |= PCC_CLKCFG_CGC( 1U ); /* Enable LPUART */ - - /* PORTB16 (pin 62) is configured as LPUART0_RX */ - gpio_pin_config_t const lpuart_config_rx = { kGPIO_DigitalInput, 0 }; - GPIO_PinInit(UART_PIN_GPIO, UART_PIN_RX, &lpuart_config_rx); - const port_pin_config_t UART_CFG = { - kPORT_PullUp, - kPORT_FastSlewRate, - kPORT_PassiveFilterDisable, - kPORT_OpenDrainDisable, - kPORT_LowDriveStrength, - kPORT_MuxAsGpio, - kPORT_UnlockRegister - }; - PORT_SetPinConfig(UART_PIN_PORT, UART_PIN_RX, &UART_CFG); - PORT_SetPinMux( UART_PIN_PORT, UART_PIN_RX, kPORT_MuxAlt3); - - /* PORTB17 (pin 63) is configured as LPUART0_TX */ - gpio_pin_config_t const lpuart_config_tx = { kGPIO_DigitalOutput, 0 }; - GPIO_PinInit( UART_PIN_GPIO, UART_PIN_TX, &lpuart_config_tx); - PORT_SetPinMux( UART_PIN_PORT, UART_PIN_TX, kPORT_MuxAlt3); - - BOARD_BootClockRUN(); - SystemCoreClockUpdate(); - -#if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); -#elif CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); -#endif - - lpuart_config_t uart_config; - LPUART_GetDefaultConfig(&uart_config); - uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE; - uart_config.enableTx = true; - uart_config.enableRx = true; - LPUART_Init(UART_PORT, &uart_config, CLOCK_GetFreq(kCLOCK_ScgFircClk)); - - // USB - CLOCK_EnableUsbfs0Clock(kCLOCK_IpSrcFircAsync, 48000000U); -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); -} - -uint32_t board_button_read(void) -{ - return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); -} - -int board_uart_read(uint8_t* buf, int len) -{ -#if 0 /* - Use this version if want the LED to blink during BOARD=board_test, - without having to hit a key. - */ - if( 0U != (kLPUART_RxDataRegFullFlag & LPUART_GetStatusFlags( UART_PORT )) ) - { - LPUART_ReadBlocking(UART_PORT, buf, len); - return len; - } - - return( 0 ); -#else /* Wait for 'len' characters to come in */ - - LPUART_ReadBlocking(UART_PORT, buf, len); - return len; - -#endif -} - -int board_uart_write(void const * buf, int len) -{ - LPUART_WriteBlocking(UART_PORT, (uint8_t const*) buf, len); - return len; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif diff --git a/hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.h b/hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.h deleted file mode 100644 index 8d21fdcd4..000000000 --- a/hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.h +++ /dev/null @@ -1,56 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - - -#ifndef BOARD_H_ -#define BOARD_H_ - -#include "fsl_device_registers.h" - -// LED -#define LED_PIN_CLOCK kCLOCK_PortD -#define LED_GPIO GPIOD -#define LED_PORT PORTD -#define LED_PIN 5 -#define LED_STATE_ON 0 - -// SW3 button1 -#define BUTTON_PIN_CLOCK kCLOCK_PortC -#define BUTTON_GPIO GPIOC -#define BUTTON_PORT PORTC -#define BUTTON_PIN 3 -#define BUTTON_STATE_ACTIVE 0 - -// UART -#define UART_PORT LPUART0 -#define UART_PIN_CLOCK kCLOCK_PortA -#define UART_PIN_PORT PORTA -#define UART_PIN_RX 1u -#define UART_PIN_TX 2u -#define SOPT5_LPUART0RXSRC_LPUART_RX 0x00u /*!<@brief LPUART0 Receive Data Source Select: LPUART_RX pin */ -#define SOPT5_LPUART0TXSRC_LPUART_TX 0x00u /*!<@brief LPUART0 Transmit Data Source Select: LPUART0_TX pin */ - -#endif /* BOARD_H_ */ diff --git a/hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.mk b/hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.mk deleted file mode 100644 index 5f8ecbfe4..000000000 --- a/hw/bsp/kinetis_k32/boards/frdm_k32l2b/board.mk +++ /dev/null @@ -1,26 +0,0 @@ -MCU = K32L2B31A - -CFLAGS += \ - -mcpu=cortex-m0plus \ - -DCPU_K32L2B31VLH0A \ - -# mcu driver cause following warnings -CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls - -# All source paths should be relative to the top level. -LD_FILE = $(MCU_DIR)/gcc/K32L2B31xxxxA_flash.ld - -SRC_C += \ - $(MCU_DIR)/project_template/clock_config.c \ - -# For freeRTOS port source -FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM0 - -# For flash-jlink target -JLINK_DEVICE = K32L2B31xxxxA - -# For flash-pyocd target -PYOCD_TARGET = K32L2B - -# flash using pyocd -flash: flash-pyocd diff --git a/hw/bsp/kinetis_k32/boards/frdm_k32l2b/frdm_k32l2b.c b/hw/bsp/kinetis_k32/boards/frdm_k32l2b/frdm_k32l2b.c deleted file mode 100644 index 1566b4e2e..000000000 --- a/hw/bsp/kinetis_k32/boards/frdm_k32l2b/frdm_k32l2b.c +++ /dev/null @@ -1,140 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2018, hathach (tinyusb.org) - * Copyright (c) 2020, Koji Kitayama - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "bsp/board.h" -#include "board.h" -#include "fsl_gpio.h" -#include "fsl_port.h" -#include "fsl_clock.h" -#include "fsl_lpuart.h" - -#include "clock_config.h" - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void USB0_IRQHandler(void) -{ - tud_int_handler(0); -} - -void board_init(void) -{ - /* Enable port clocks for UART/LED/Button pins */ - CLOCK_EnableClock(UART_PIN_CLOCK); - CLOCK_EnableClock(LED_PIN_CLOCK); - CLOCK_EnableClock(BUTTON_PIN_CLOCK); - - gpio_pin_config_t led_config = { kGPIO_DigitalOutput, 0 }; - GPIO_PinInit(LED_GPIO, LED_PIN, &led_config); - PORT_SetPinMux(LED_PORT, LED_PIN, kPORT_MuxAsGpio); - - gpio_pin_config_t button_config = { kGPIO_DigitalInput, 0 }; - GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); - const port_pin_config_t BUTTON_CFG = { - kPORT_PullUp, - kPORT_FastSlewRate, - kPORT_PassiveFilterDisable, - kPORT_LowDriveStrength, - kPORT_MuxAsGpio - }; - PORT_SetPinConfig(BUTTON_PORT, BUTTON_PIN, &BUTTON_CFG); - - /* PORTA1 (pin 23) is configured as LPUART0_RX */ - PORT_SetPinMux(PORTA, 1U, kPORT_MuxAlt2); - /* PORTA2 (pin 24) is configured as LPUART0_TX */ - PORT_SetPinMux(PORTA, 2U, kPORT_MuxAlt2); - - SIM->SOPT5 = ((SIM->SOPT5 & - /* Mask bits to zero which are setting */ - (~(SIM_SOPT5_LPUART0TXSRC_MASK | SIM_SOPT5_LPUART0RXSRC_MASK))) - /* LPUART0 Transmit Data Source Select: LPUART0_TX pin. */ - | SIM_SOPT5_LPUART0TXSRC(SOPT5_LPUART0TXSRC_LPUART_TX) - /* LPUART0 Receive Data Source Select: LPUART_RX pin. */ - | SIM_SOPT5_LPUART0RXSRC(SOPT5_LPUART0RXSRC_LPUART_RX)); - - BOARD_BootClockRUN(); - SystemCoreClockUpdate(); - CLOCK_SetLpuart0Clock(1); - -#if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); -#elif CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); -#endif - - lpuart_config_t uart_config; - LPUART_GetDefaultConfig(&uart_config); - uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE; - uart_config.enableTx = true; - uart_config.enableRx = true; - LPUART_Init(UART_PORT, &uart_config, CLOCK_GetFreq(kCLOCK_McgIrc48MClk)); - - // USB - CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcIrc48M, 48000000U); -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); -} - -uint32_t board_button_read(void) -{ - return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); -} - -int board_uart_read(uint8_t* buf, int len) -{ - LPUART_ReadBlocking(UART_PORT, buf, len); - return len; -} - -int board_uart_write(void const * buf, int len) -{ - LPUART_WriteBlocking(UART_PORT, (uint8_t const*) buf, len); - return len; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif diff --git a/hw/bsp/kinetis_k32/boards/kuiic/K32L2B31xxxxA_flash.ld b/hw/bsp/kinetis_k32/boards/kuiic/K32L2B31xxxxA_flash.ld deleted file mode 100644 index f478a99c7..000000000 --- a/hw/bsp/kinetis_k32/boards/kuiic/K32L2B31xxxxA_flash.ld +++ /dev/null @@ -1,216 +0,0 @@ -/* -** ################################################################### -** Processors: K32L2B31VFM0A -** K32L2B31VFT0A -** K32L2B31VLH0A -** K32L2B31VMP0A -** -** Compiler: GNU C Compiler -** Reference manual: K32L2B3xRM, Rev.0, July 2019 -** Version: rev. 1.0, 2019-07-30 -** Build: b190930 -** -** Abstract: -** Linker file for the GNU C Compiler -** -** Copyright 2016 Freescale Semiconductor, Inc. -** Copyright 2016-2019 NXP -** All rights reserved. -** -** SPDX-License-Identifier: BSD-3-Clause -** -** http: www.nxp.com -** mail: support@nxp.com -** -** ################################################################### -*/ - -/* Entry Point */ -ENTRY(Reset_Handler) - -HEAP_SIZE = DEFINED(__heap_size__) ? __heap_size__ : 0x0400; -STACK_SIZE = DEFINED(__stack_size__) ? __stack_size__ : 0x0400; - -/* Specify the memory areas */ -MEMORY -{ - m_interrupts (RX) : ORIGIN = 0x00008000, LENGTH = 0x00000200 - m_flash_config (RX) : ORIGIN = 0x00008400, LENGTH = 0x00000010 - m_text (RX) : ORIGIN = 0x00008410, LENGTH = 0x00037BF0 - m_data (RW) : ORIGIN = 0x1FFFE000, LENGTH = 0x00008000 -} - -/* Define output sections */ -SECTIONS -{ - /* The startup code goes first into internal flash */ - .interrupts : - { - . = ALIGN(4); - KEEP(*(.isr_vector)) /* Startup code */ - . = ALIGN(4); - } > m_interrupts - - .flash_config : - { - . = ALIGN(4); - KEEP(*(.FlashConfig)) /* Flash Configuration Field (FCF) */ - . = ALIGN(4); - } > m_flash_config - - /* The program code and other data goes into internal flash */ - .text : - { - . = ALIGN(4); - *(.text) /* .text sections (code) */ - *(.text*) /* .text* sections (code) */ - *(.rodata) /* .rodata sections (constants, strings, etc.) */ - *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ - *(.glue_7) /* glue arm to thumb code */ - *(.glue_7t) /* glue thumb to arm code */ - *(.eh_frame) - KEEP (*(.init)) - KEEP (*(.fini)) - . = ALIGN(4); - } > m_text - - .ARM.extab : - { - *(.ARM.extab* .gnu.linkonce.armextab.*) - } > m_text - - .ARM : - { - __exidx_start = .; - *(.ARM.exidx*) - __exidx_end = .; - } > m_text - - .ctors : - { - __CTOR_LIST__ = .; - /* gcc uses crtbegin.o to find the start of - the constructors, so we make sure it is - first. Because this is a wildcard, it - doesn't matter if the user does not - actually link against crtbegin.o; the - linker won't look for a file to match a - wildcard. The wildcard also means that it - doesn't matter which directory crtbegin.o - is in. */ - KEEP (*crtbegin.o(.ctors)) - KEEP (*crtbegin?.o(.ctors)) - /* We don't want to include the .ctor section from - from the crtend.o file until after the sorted ctors. - The .ctor section from the crtend file contains the - end of ctors marker and it must be last */ - KEEP (*(EXCLUDE_FILE(*crtend?.o *crtend.o) .ctors)) - KEEP (*(SORT(.ctors.*))) - KEEP (*(.ctors)) - __CTOR_END__ = .; - } > m_text - - .dtors : - { - __DTOR_LIST__ = .; - KEEP (*crtbegin.o(.dtors)) - KEEP (*crtbegin?.o(.dtors)) - KEEP (*(EXCLUDE_FILE(*crtend?.o *crtend.o) .dtors)) - KEEP (*(SORT(.dtors.*))) - KEEP (*(.dtors)) - __DTOR_END__ = .; - } > m_text - - .preinit_array : - { - PROVIDE_HIDDEN (__preinit_array_start = .); - KEEP (*(.preinit_array*)) - PROVIDE_HIDDEN (__preinit_array_end = .); - } > m_text - - .init_array : - { - PROVIDE_HIDDEN (__init_array_start = .); - KEEP (*(SORT(.init_array.*))) - KEEP (*(.init_array*)) - PROVIDE_HIDDEN (__init_array_end = .); - } > m_text - - .fini_array : - { - PROVIDE_HIDDEN (__fini_array_start = .); - KEEP (*(SORT(.fini_array.*))) - KEEP (*(.fini_array*)) - PROVIDE_HIDDEN (__fini_array_end = .); - } > m_text - - __etext = .; /* define a global symbol at end of code */ - __DATA_ROM = .; /* Symbol is used by startup for data initialization */ - - /* reserve MTB memory at the beginning of m_data */ - .mtb : /* MTB buffer address as defined by the hardware */ - { - . = ALIGN(8); - _mtb_start = .; - KEEP(*(.mtb_buf)) /* need to KEEP Micro Trace Buffer as not referenced by application */ - . = ALIGN(8); - _mtb_end = .; - } > m_data - - .data : AT(__DATA_ROM) - { - . = ALIGN(4); - __DATA_RAM = .; - __data_start__ = .; /* create a global symbol at data start */ - *(.data) /* .data sections */ - *(.data*) /* .data* sections */ - KEEP(*(.jcr*)) - . = ALIGN(4); - __data_end__ = .; /* define a global symbol at data end */ - } > m_data - - __DATA_END = __DATA_ROM + (__data_end__ - __data_start__); - text_end = ORIGIN(m_text) + LENGTH(m_text); - ASSERT(__DATA_END <= text_end, "region m_text overflowed with text and data") - - /* Uninitialized data section */ - .bss : - { - /* This is used by the startup in order to initialize the .bss section */ - . = ALIGN(4); - __START_BSS = .; - __bss_start__ = .; - *(.bss) - *(.bss*) - *(COMMON) - . = ALIGN(4); - __bss_end__ = .; - __END_BSS = .; - } > m_data - - .heap : - { - . = ALIGN(8); - __end__ = .; - PROVIDE(end = .); - __HeapBase = .; - . += HEAP_SIZE; - __HeapLimit = .; - __heap_limit = .; /* Add for _sbrk */ - } > m_data - - .stack : - { - . = ALIGN(8); - . += STACK_SIZE; - } > m_data - - /* Initializes stack on the end of block */ - __StackTop = ORIGIN(m_data) + LENGTH(m_data); - __StackLimit = __StackTop - STACK_SIZE; - PROVIDE(__stack = __StackTop); - - .ARM.attributes 0 : { *(.ARM.attributes) } - - ASSERT(__StackLimit >= __HeapLimit, "region m_data overflowed with stack and heap") -} diff --git a/hw/bsp/kinetis_k32/boards/kuiic/board.h b/hw/bsp/kinetis_k32/boards/kuiic/board.h deleted file mode 100644 index 1e2d4f18b..000000000 --- a/hw/bsp/kinetis_k32/boards/kuiic/board.h +++ /dev/null @@ -1,45 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - - -#ifndef BOARD_H_ -#define BOARD_H_ - -#include "fsl_device_registers.h" - -// LED -#define LED_PIN_CLOCK kCLOCK_PortA -#define LED_GPIO GPIOA -#define LED_PORT PORTA -#define LED_PIN 2 -#define LED_STATE_ON 1 - -// UART -#define UART_PORT LPUART1 -#define UART_PIN_RX 3u -#define UART_PIN_TX 0u - -#endif /* BOARD_H_ */ diff --git a/hw/bsp/kinetis_k32/boards/kuiic/board.mk b/hw/bsp/kinetis_k32/boards/kuiic/board.mk deleted file mode 100644 index 29a12e982..000000000 --- a/hw/bsp/kinetis_k32/boards/kuiic/board.mk +++ /dev/null @@ -1,26 +0,0 @@ -MCU = K32L2B31A - -# This board uses TinyUF2 for updates -UF2_FAMILY_ID = 0x7f83e793 - -CFLAGS += \ - -mcpu=cortex-m0plus \ - -DCPU_K32L2B31VLH0A \ - -# mcu driver cause following warnings -CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls - -# All source paths should be relative to the top level. -LD_FILE = $(BOARD_PATH)/K32L2B31xxxxA_flash.ld - -# For freeRTOS port source -FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM0 - -# For flash-jlink target -JLINK_DEVICE = K32L2B31xxxxA - -# For flash-pyocd target -PYOCD_TARGET = K32L2B - -# flash using pyocd -flash: flash-pyocd diff --git a/hw/bsp/kinetis_k32/boards/kuiic/kuiic.c b/hw/bsp/kinetis_k32/boards/kuiic/kuiic.c deleted file mode 100644 index f9002a6d3..000000000 --- a/hw/bsp/kinetis_k32/boards/kuiic/kuiic.c +++ /dev/null @@ -1,203 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2018, hathach (tinyusb.org) - * Copyright (c) 2020, Koji Kitayama - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "bsp/board.h" -#include "board.h" -#include "fsl_smc.h" -#include "fsl_gpio.h" -#include "fsl_port.h" -#include "fsl_clock.h" -#include "fsl_lpuart.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ -#define SIM_OSC32KSEL_LPO_CLK 3U /*!< OSC32KSEL select: LPO clock */ -#define SOPT5_LPUART1RXSRC_LPUART_RX 0x00u /*!<@brief LPUART1 Receive Data Source Select: LPUART_RX pin */ -#define SOPT5_LPUART1TXSRC_LPUART_TX 0x00u /*!<@brief LPUART1 Transmit Data Source Select: LPUART_TX pin */ -#define BOARD_BOOTCLOCKRUN_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ - -/******************************************************************************* - * Variables - ******************************************************************************/ -/* System clock frequency. */ -// extern uint32_t SystemCoreClock; - -/******************************************************************************* - * Variables for BOARD_BootClockRUN configuration - ******************************************************************************/ -const mcglite_config_t mcgliteConfig_BOARD_BootClockRUN = { - .outSrc = kMCGLITE_ClkSrcHirc, /* MCGOUTCLK source is HIRC */ - .irclkEnableMode = kMCGLITE_IrclkEnable, /* MCGIRCLK enabled, MCGIRCLK disabled in STOP mode */ - .ircs = kMCGLITE_Lirc8M, /* Slow internal reference (LIRC) 8 MHz clock selected */ - .fcrdiv = kMCGLITE_LircDivBy1, /* Low-frequency Internal Reference Clock Divider: divided by 1 */ - .lircDiv2 = kMCGLITE_LircDivBy1, /* Second Low-frequency Internal Reference Clock Divider: divided by 1 */ - .hircEnableInNotHircMode = true, /* HIRC source is enabled */ -}; -const sim_clock_config_t simConfig_BOARD_BootClockRUN = { - .er32kSrc = SIM_OSC32KSEL_LPO_CLK, /* OSC32KSEL select: LPO clock */ - .clkdiv1 = 0x10000U, /* SIM_CLKDIV1 - OUTDIV1: /1, OUTDIV4: /2 */ -}; - -/******************************************************************************* - * Code for BOARD_BootClockRUN configuration - ******************************************************************************/ -void BOARD_BootClockRUN(void) -{ - /* Set the system clock dividers in SIM to safe value. */ - CLOCK_SetSimSafeDivs(); - /* Set MCG to HIRC mode. */ - CLOCK_SetMcgliteConfig(&mcgliteConfig_BOARD_BootClockRUN); - /* Set the clock configuration in SIM module. */ - CLOCK_SetSimConfig(&simConfig_BOARD_BootClockRUN); - /* Set SystemCoreClock variable. */ - SystemCoreClock = BOARD_BOOTCLOCKRUN_CORE_CLOCK; -} - - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void USB0_IRQHandler(void) -{ - tud_int_handler(0); -} - -void board_init(void) -{ - /* Enable port clocks for GPIO pins */ - CLOCK_EnableClock(kCLOCK_PortA); - CLOCK_EnableClock(kCLOCK_PortB); - CLOCK_EnableClock(kCLOCK_PortC); - CLOCK_EnableClock(kCLOCK_PortD); - CLOCK_EnableClock(kCLOCK_PortE); - - - gpio_pin_config_t led_config = { kGPIO_DigitalOutput, 1 }; - GPIO_PinInit(GPIOA, 1U, &led_config); - PORT_SetPinMux(PORTA, 1U, kPORT_MuxAsGpio); - led_config.outputLogic = 0; - GPIO_PinInit(GPIOA, 2U, &led_config); - PORT_SetPinMux(PORTA, 2U, kPORT_MuxAsGpio); - -#ifdef BUTTON_PIN - gpio_pin_config_t button_config = { kGPIO_DigitalInput, 0 }; - GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); - const port_pin_config_t BUTTON_CFG = { - kPORT_PullUp, - kPORT_FastSlewRate, - kPORT_PassiveFilterDisable, - kPORT_LowDriveStrength, - kPORT_MuxAsGpio - }; - PORT_SetPinConfig(BUTTON_PORT, BUTTON_PIN, &BUTTON_CFG); -#endif - - /* PORTC3 is configured as LPUART0_RX */ - PORT_SetPinMux(PORTC, 3U, kPORT_MuxAlt3); - /* PORTA2 (pin 24) is configured as LPUART0_TX */ - PORT_SetPinMux(PORTE, 0U, kPORT_MuxAlt3); - - SIM->SOPT5 = ((SIM->SOPT5 & - /* Mask bits to zero which are setting */ - (~(SIM_SOPT5_LPUART1TXSRC_MASK | SIM_SOPT5_LPUART1RXSRC_MASK))) - /* LPUART0 Transmit Data Source Select: LPUART0_TX pin. */ - | SIM_SOPT5_LPUART1TXSRC(SOPT5_LPUART1TXSRC_LPUART_TX) - /* LPUART0 Receive Data Source Select: LPUART_RX pin. */ - | SIM_SOPT5_LPUART1RXSRC(SOPT5_LPUART1RXSRC_LPUART_RX)); - - BOARD_BootClockRUN(); - SystemCoreClockUpdate(); - CLOCK_SetLpuart1Clock(1); - -#if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); -#elif CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); -#endif - - lpuart_config_t uart_config; - LPUART_GetDefaultConfig(&uart_config); - uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE; - uart_config.enableTx = true; - uart_config.enableRx = true; - LPUART_Init(UART_PORT, &uart_config, CLOCK_GetFreq(kCLOCK_McgIrc48MClk)); - - // USB - CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcIrc48M, 48000000U); -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - if (state) { - LED_GPIO->PDDR |= GPIO_FIT_REG((1UL << LED_PIN)); - } else { - LED_GPIO->PDDR &= GPIO_FIT_REG(~(1UL << LED_PIN)); - } -// GPIO_PinWrite(GPIOA, 1, state ? LED_STATE_ON : (1-LED_STATE_ON) ); -// GPIO_PinWrite(GPIOA, 2, state ? (1-LED_STATE_ON) : LED_STATE_ON ); -} - -uint32_t board_button_read(void) -{ -#ifdef BUTTON_PIN - return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); -#else - return 0; -#endif -} - -int board_uart_read(uint8_t* buf, int len) -{ - LPUART_ReadBlocking(UART_PORT, buf, len); - return len; -} - -int board_uart_write(void const * buf, int len) -{ - LPUART_WriteBlocking(UART_PORT, (uint8_t const*) buf, len); - return len; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif diff --git a/hw/bsp/kinetis_k32/family.mk b/hw/bsp/kinetis_k32/family.mk deleted file mode 100644 index 41f22e250..000000000 --- a/hw/bsp/kinetis_k32/family.mk +++ /dev/null @@ -1,32 +0,0 @@ -SDK_DIR = hw/mcu/nxp/mcux-sdk -DEPS_SUBMODULES += $(SDK_DIR) lib/CMSIS_5 - -MCU_DIR = $(SDK_DIR)/devices/$(MCU) -include $(TOP)/$(BOARD_PATH)/board.mk - -CFLAGS += \ - -mthumb \ - -mabi=aapcs \ - -DCFG_TUSB_MCU=OPT_MCU_KINETIS_K32 - -SRC_C += \ - src/portable/nxp/khci/dcd_khci.c \ - src/portable/nxp/khci/hcd_khci.c \ - $(MCU_DIR)/system_$(MCU).c \ - $(MCU_DIR)/drivers/fsl_clock.c \ - $(SDK_DIR)/drivers/gpio/fsl_gpio.c \ - $(SDK_DIR)/drivers/lpuart/fsl_lpuart.c - -INC += \ - $(TOP)/$(BOARD_PATH) \ - $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ - $(TOP)/$(MCU_DIR) \ - $(TOP)/$(MCU_DIR)/project_template \ - $(TOP)/$(MCU_DIR)/drivers \ - $(TOP)/$(SDK_DIR)/drivers/smc \ - $(TOP)/$(SDK_DIR)/drivers/common \ - $(TOP)/$(SDK_DIR)/drivers/gpio \ - $(TOP)/$(SDK_DIR)/drivers/port \ - $(TOP)/$(SDK_DIR)/drivers/lpuart \ - -SRC_S += $(MCU_DIR)/gcc/startup_$(MCU).S diff --git a/hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.h b/hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.h new file mode 100644 index 000000000..b1f38c997 --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.h @@ -0,0 +1,58 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + + +#ifndef BOARD_H_ +#define BOARD_H_ + +#include "fsl_device_registers.h" + +// LED +// The Red LED is on PTE29. +// The Green LED is on PTC4. +// The Blue LED is on PTE31. +#define LED_PIN_CLOCK kCLOCK_PortC +#define LED_GPIO GPIOC +#define LED_PORT PORTC +#define LED_PIN 4 +#define LED_STATE_ON 0 + +// SW3 button1 +#define BUTTON_PIN_CLOCK kCLOCK_PortE +#define BUTTON_GPIO GPIOE +#define BUTTON_PORT PORTE +#define BUTTON_PIN 4 +#define BUTTON_STATE_ACTIVE 0 + +// UART +#define UART_PORT LPUART0 +#define UART_PIN_CLOCK kCLOCK_PortB +#define UART_PIN_GPIO GPIOB +#define UART_PIN_PORT PORTB +#define UART_PIN_RX 16u +#define UART_PIN_TX 17u + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.mk b/hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.mk new file mode 100644 index 000000000..d96ab58b8 --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/board.mk @@ -0,0 +1,26 @@ +MCU = K32L2A41A + +CFLAGS += \ + -mcpu=cortex-m0plus \ + -DCPU_K32L2A41VLH1A \ + +# mcu driver cause following warnings +CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls -Wno-error=cast-qual + +# All source paths should be relative to the top level. +LD_FILE = $(MCU_DIR)/gcc/K32L2A41xxxxA_flash.ld + +SRC_C += \ + $(MCU_DIR)/project_template/clock_config.c \ + +# For freeRTOS port source +FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM0 + +# For flash-jlink target +JLINK_DEVICE = K32L2A41xxxxA + +# For flash-pyocd target +PYOCD_TARGET = K32L2A + +# flash using pyocd +flash: flash-pyocd diff --git a/hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/frdm_k32l2a4s.c b/hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/frdm_k32l2a4s.c new file mode 100644 index 000000000..80830163b --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/frdm_k32l2a4s/frdm_k32l2a4s.c @@ -0,0 +1,171 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2018, hathach (tinyusb.org) + * Copyright (c) 2020, Koji Kitayama + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board.h" +#include "board.h" +#include "fsl_gpio.h" +#include "fsl_port.h" +#include "fsl_clock.h" +#include "fsl_lpuart.h" + +#include "clock_config.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB0_IRQHandler(void) +{ + tud_int_handler(0); +} + +void board_init(void) +{ + /* Enable port clocks for UART/LED/Button pins */ + CLOCK_EnableClock(UART_PIN_CLOCK); + CLOCK_EnableClock(LED_PIN_CLOCK); + CLOCK_EnableClock(BUTTON_PIN_CLOCK); + + gpio_pin_config_t led_config = { kGPIO_DigitalOutput, 0 }; + GPIO_PinInit(LED_GPIO, LED_PIN, &led_config); + PORT_SetPinMux(LED_PORT, LED_PIN, kPORT_MuxAsGpio); + + gpio_pin_config_t button_config = { kGPIO_DigitalInput, 0 }; + GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); + const port_pin_config_t BUTTON_CFG = { + kPORT_PullUp, + kPORT_FastSlewRate, + kPORT_PassiveFilterDisable, + kPORT_OpenDrainDisable, + kPORT_LowDriveStrength, + kPORT_MuxAsGpio, + kPORT_UnlockRegister + }; + PORT_SetPinConfig(BUTTON_PORT, BUTTON_PIN, &BUTTON_CFG); + + /* + Enable LPUART0 clock and configure port pins. + FIR clock is being used so the USB examples work. + */ + PCC_LPUART0 = 0U; /* Clock must be off to set PCS */ + PCC_LPUART0 = PCC_CLKCFG_PCS( 3U ); /* Select the clock. 1:OSCCLK/Bus Clock, 2:Slow IRC, 3: Fast IRC, 6: System PLL */ + PCC_LPUART0 |= PCC_CLKCFG_CGC( 1U ); /* Enable LPUART */ + + /* PORTB16 (pin 62) is configured as LPUART0_RX */ + gpio_pin_config_t const lpuart_config_rx = { kGPIO_DigitalInput, 0 }; + GPIO_PinInit(UART_PIN_GPIO, UART_PIN_RX, &lpuart_config_rx); + const port_pin_config_t UART_CFG = { + kPORT_PullUp, + kPORT_FastSlewRate, + kPORT_PassiveFilterDisable, + kPORT_OpenDrainDisable, + kPORT_LowDriveStrength, + kPORT_MuxAsGpio, + kPORT_UnlockRegister + }; + PORT_SetPinConfig(UART_PIN_PORT, UART_PIN_RX, &UART_CFG); + PORT_SetPinMux( UART_PIN_PORT, UART_PIN_RX, kPORT_MuxAlt3); + + /* PORTB17 (pin 63) is configured as LPUART0_TX */ + gpio_pin_config_t const lpuart_config_tx = { kGPIO_DigitalOutput, 0 }; + GPIO_PinInit( UART_PIN_GPIO, UART_PIN_TX, &lpuart_config_tx); + PORT_SetPinMux( UART_PIN_PORT, UART_PIN_TX, kPORT_MuxAlt3); + + BOARD_BootClockRUN(); + SystemCoreClockUpdate(); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#elif CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); +#endif + + lpuart_config_t uart_config; + LPUART_GetDefaultConfig(&uart_config); + uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE; + uart_config.enableTx = true; + uart_config.enableRx = true; + LPUART_Init(UART_PORT, &uart_config, CLOCK_GetFreq(kCLOCK_ScgFircClk)); + + // USB + CLOCK_EnableUsbfs0Clock(kCLOCK_IpSrcFircAsync, 48000000U); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +} + +uint32_t board_button_read(void) +{ + return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); +} + +int board_uart_read(uint8_t* buf, int len) +{ +#if 0 /* + Use this version if want the LED to blink during BOARD=board_test, + without having to hit a key. + */ + if( 0U != (kLPUART_RxDataRegFullFlag & LPUART_GetStatusFlags( UART_PORT )) ) + { + LPUART_ReadBlocking(UART_PORT, buf, len); + return len; + } + + return( 0 ); +#else /* Wait for 'len' characters to come in */ + + LPUART_ReadBlocking(UART_PORT, buf, len); + return len; + +#endif +} + +int board_uart_write(void const * buf, int len) +{ + LPUART_WriteBlocking(UART_PORT, (uint8_t const*) buf, len); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif diff --git a/hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.h b/hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.h new file mode 100644 index 000000000..8d21fdcd4 --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.h @@ -0,0 +1,56 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + + +#ifndef BOARD_H_ +#define BOARD_H_ + +#include "fsl_device_registers.h" + +// LED +#define LED_PIN_CLOCK kCLOCK_PortD +#define LED_GPIO GPIOD +#define LED_PORT PORTD +#define LED_PIN 5 +#define LED_STATE_ON 0 + +// SW3 button1 +#define BUTTON_PIN_CLOCK kCLOCK_PortC +#define BUTTON_GPIO GPIOC +#define BUTTON_PORT PORTC +#define BUTTON_PIN 3 +#define BUTTON_STATE_ACTIVE 0 + +// UART +#define UART_PORT LPUART0 +#define UART_PIN_CLOCK kCLOCK_PortA +#define UART_PIN_PORT PORTA +#define UART_PIN_RX 1u +#define UART_PIN_TX 2u +#define SOPT5_LPUART0RXSRC_LPUART_RX 0x00u /*!<@brief LPUART0 Receive Data Source Select: LPUART_RX pin */ +#define SOPT5_LPUART0TXSRC_LPUART_TX 0x00u /*!<@brief LPUART0 Transmit Data Source Select: LPUART0_TX pin */ + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.mk b/hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.mk new file mode 100644 index 000000000..5f8ecbfe4 --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/frdm_k32l2b/board.mk @@ -0,0 +1,26 @@ +MCU = K32L2B31A + +CFLAGS += \ + -mcpu=cortex-m0plus \ + -DCPU_K32L2B31VLH0A \ + +# mcu driver cause following warnings +CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls + +# All source paths should be relative to the top level. +LD_FILE = $(MCU_DIR)/gcc/K32L2B31xxxxA_flash.ld + +SRC_C += \ + $(MCU_DIR)/project_template/clock_config.c \ + +# For freeRTOS port source +FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM0 + +# For flash-jlink target +JLINK_DEVICE = K32L2B31xxxxA + +# For flash-pyocd target +PYOCD_TARGET = K32L2B + +# flash using pyocd +flash: flash-pyocd diff --git a/hw/bsp/kinetis_k32l/boards/frdm_k32l2b/frdm_k32l2b.c b/hw/bsp/kinetis_k32l/boards/frdm_k32l2b/frdm_k32l2b.c new file mode 100644 index 000000000..1566b4e2e --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/frdm_k32l2b/frdm_k32l2b.c @@ -0,0 +1,140 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2018, hathach (tinyusb.org) + * Copyright (c) 2020, Koji Kitayama + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board.h" +#include "board.h" +#include "fsl_gpio.h" +#include "fsl_port.h" +#include "fsl_clock.h" +#include "fsl_lpuart.h" + +#include "clock_config.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB0_IRQHandler(void) +{ + tud_int_handler(0); +} + +void board_init(void) +{ + /* Enable port clocks for UART/LED/Button pins */ + CLOCK_EnableClock(UART_PIN_CLOCK); + CLOCK_EnableClock(LED_PIN_CLOCK); + CLOCK_EnableClock(BUTTON_PIN_CLOCK); + + gpio_pin_config_t led_config = { kGPIO_DigitalOutput, 0 }; + GPIO_PinInit(LED_GPIO, LED_PIN, &led_config); + PORT_SetPinMux(LED_PORT, LED_PIN, kPORT_MuxAsGpio); + + gpio_pin_config_t button_config = { kGPIO_DigitalInput, 0 }; + GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); + const port_pin_config_t BUTTON_CFG = { + kPORT_PullUp, + kPORT_FastSlewRate, + kPORT_PassiveFilterDisable, + kPORT_LowDriveStrength, + kPORT_MuxAsGpio + }; + PORT_SetPinConfig(BUTTON_PORT, BUTTON_PIN, &BUTTON_CFG); + + /* PORTA1 (pin 23) is configured as LPUART0_RX */ + PORT_SetPinMux(PORTA, 1U, kPORT_MuxAlt2); + /* PORTA2 (pin 24) is configured as LPUART0_TX */ + PORT_SetPinMux(PORTA, 2U, kPORT_MuxAlt2); + + SIM->SOPT5 = ((SIM->SOPT5 & + /* Mask bits to zero which are setting */ + (~(SIM_SOPT5_LPUART0TXSRC_MASK | SIM_SOPT5_LPUART0RXSRC_MASK))) + /* LPUART0 Transmit Data Source Select: LPUART0_TX pin. */ + | SIM_SOPT5_LPUART0TXSRC(SOPT5_LPUART0TXSRC_LPUART_TX) + /* LPUART0 Receive Data Source Select: LPUART_RX pin. */ + | SIM_SOPT5_LPUART0RXSRC(SOPT5_LPUART0RXSRC_LPUART_RX)); + + BOARD_BootClockRUN(); + SystemCoreClockUpdate(); + CLOCK_SetLpuart0Clock(1); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#elif CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); +#endif + + lpuart_config_t uart_config; + LPUART_GetDefaultConfig(&uart_config); + uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE; + uart_config.enableTx = true; + uart_config.enableRx = true; + LPUART_Init(UART_PORT, &uart_config, CLOCK_GetFreq(kCLOCK_McgIrc48MClk)); + + // USB + CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcIrc48M, 48000000U); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +} + +uint32_t board_button_read(void) +{ + return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); +} + +int board_uart_read(uint8_t* buf, int len) +{ + LPUART_ReadBlocking(UART_PORT, buf, len); + return len; +} + +int board_uart_write(void const * buf, int len) +{ + LPUART_WriteBlocking(UART_PORT, (uint8_t const*) buf, len); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif diff --git a/hw/bsp/kinetis_k32l/boards/kuiic/K32L2B31xxxxA_flash.ld b/hw/bsp/kinetis_k32l/boards/kuiic/K32L2B31xxxxA_flash.ld new file mode 100644 index 000000000..f478a99c7 --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/kuiic/K32L2B31xxxxA_flash.ld @@ -0,0 +1,216 @@ +/* +** ################################################################### +** Processors: K32L2B31VFM0A +** K32L2B31VFT0A +** K32L2B31VLH0A +** K32L2B31VMP0A +** +** Compiler: GNU C Compiler +** Reference manual: K32L2B3xRM, Rev.0, July 2019 +** Version: rev. 1.0, 2019-07-30 +** Build: b190930 +** +** Abstract: +** Linker file for the GNU C Compiler +** +** Copyright 2016 Freescale Semiconductor, Inc. +** Copyright 2016-2019 NXP +** All rights reserved. +** +** SPDX-License-Identifier: BSD-3-Clause +** +** http: www.nxp.com +** mail: support@nxp.com +** +** ################################################################### +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +HEAP_SIZE = DEFINED(__heap_size__) ? __heap_size__ : 0x0400; +STACK_SIZE = DEFINED(__stack_size__) ? __stack_size__ : 0x0400; + +/* Specify the memory areas */ +MEMORY +{ + m_interrupts (RX) : ORIGIN = 0x00008000, LENGTH = 0x00000200 + m_flash_config (RX) : ORIGIN = 0x00008400, LENGTH = 0x00000010 + m_text (RX) : ORIGIN = 0x00008410, LENGTH = 0x00037BF0 + m_data (RW) : ORIGIN = 0x1FFFE000, LENGTH = 0x00008000 +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into internal flash */ + .interrupts : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } > m_interrupts + + .flash_config : + { + . = ALIGN(4); + KEEP(*(.FlashConfig)) /* Flash Configuration Field (FCF) */ + . = ALIGN(4); + } > m_flash_config + + /* The program code and other data goes into internal flash */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + KEEP (*(.init)) + KEEP (*(.fini)) + . = ALIGN(4); + } > m_text + + .ARM.extab : + { + *(.ARM.extab* .gnu.linkonce.armextab.*) + } > m_text + + .ARM : + { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } > m_text + + .ctors : + { + __CTOR_LIST__ = .; + /* gcc uses crtbegin.o to find the start of + the constructors, so we make sure it is + first. Because this is a wildcard, it + doesn't matter if the user does not + actually link against crtbegin.o; the + linker won't look for a file to match a + wildcard. The wildcard also means that it + doesn't matter which directory crtbegin.o + is in. */ + KEEP (*crtbegin.o(.ctors)) + KEEP (*crtbegin?.o(.ctors)) + /* We don't want to include the .ctor section from + from the crtend.o file until after the sorted ctors. + The .ctor section from the crtend file contains the + end of ctors marker and it must be last */ + KEEP (*(EXCLUDE_FILE(*crtend?.o *crtend.o) .ctors)) + KEEP (*(SORT(.ctors.*))) + KEEP (*(.ctors)) + __CTOR_END__ = .; + } > m_text + + .dtors : + { + __DTOR_LIST__ = .; + KEEP (*crtbegin.o(.dtors)) + KEEP (*crtbegin?.o(.dtors)) + KEEP (*(EXCLUDE_FILE(*crtend?.o *crtend.o) .dtors)) + KEEP (*(SORT(.dtors.*))) + KEEP (*(.dtors)) + __DTOR_END__ = .; + } > m_text + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } > m_text + + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } > m_text + + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } > m_text + + __etext = .; /* define a global symbol at end of code */ + __DATA_ROM = .; /* Symbol is used by startup for data initialization */ + + /* reserve MTB memory at the beginning of m_data */ + .mtb : /* MTB buffer address as defined by the hardware */ + { + . = ALIGN(8); + _mtb_start = .; + KEEP(*(.mtb_buf)) /* need to KEEP Micro Trace Buffer as not referenced by application */ + . = ALIGN(8); + _mtb_end = .; + } > m_data + + .data : AT(__DATA_ROM) + { + . = ALIGN(4); + __DATA_RAM = .; + __data_start__ = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + KEEP(*(.jcr*)) + . = ALIGN(4); + __data_end__ = .; /* define a global symbol at data end */ + } > m_data + + __DATA_END = __DATA_ROM + (__data_end__ - __data_start__); + text_end = ORIGIN(m_text) + LENGTH(m_text); + ASSERT(__DATA_END <= text_end, "region m_text overflowed with text and data") + + /* Uninitialized data section */ + .bss : + { + /* This is used by the startup in order to initialize the .bss section */ + . = ALIGN(4); + __START_BSS = .; + __bss_start__ = .; + *(.bss) + *(.bss*) + *(COMMON) + . = ALIGN(4); + __bss_end__ = .; + __END_BSS = .; + } > m_data + + .heap : + { + . = ALIGN(8); + __end__ = .; + PROVIDE(end = .); + __HeapBase = .; + . += HEAP_SIZE; + __HeapLimit = .; + __heap_limit = .; /* Add for _sbrk */ + } > m_data + + .stack : + { + . = ALIGN(8); + . += STACK_SIZE; + } > m_data + + /* Initializes stack on the end of block */ + __StackTop = ORIGIN(m_data) + LENGTH(m_data); + __StackLimit = __StackTop - STACK_SIZE; + PROVIDE(__stack = __StackTop); + + .ARM.attributes 0 : { *(.ARM.attributes) } + + ASSERT(__StackLimit >= __HeapLimit, "region m_data overflowed with stack and heap") +} diff --git a/hw/bsp/kinetis_k32l/boards/kuiic/board.h b/hw/bsp/kinetis_k32l/boards/kuiic/board.h new file mode 100644 index 000000000..1e2d4f18b --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/kuiic/board.h @@ -0,0 +1,45 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + + +#ifndef BOARD_H_ +#define BOARD_H_ + +#include "fsl_device_registers.h" + +// LED +#define LED_PIN_CLOCK kCLOCK_PortA +#define LED_GPIO GPIOA +#define LED_PORT PORTA +#define LED_PIN 2 +#define LED_STATE_ON 1 + +// UART +#define UART_PORT LPUART1 +#define UART_PIN_RX 3u +#define UART_PIN_TX 0u + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/kinetis_k32l/boards/kuiic/board.mk b/hw/bsp/kinetis_k32l/boards/kuiic/board.mk new file mode 100644 index 000000000..29a12e982 --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/kuiic/board.mk @@ -0,0 +1,26 @@ +MCU = K32L2B31A + +# This board uses TinyUF2 for updates +UF2_FAMILY_ID = 0x7f83e793 + +CFLAGS += \ + -mcpu=cortex-m0plus \ + -DCPU_K32L2B31VLH0A \ + +# mcu driver cause following warnings +CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls + +# All source paths should be relative to the top level. +LD_FILE = $(BOARD_PATH)/K32L2B31xxxxA_flash.ld + +# For freeRTOS port source +FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM0 + +# For flash-jlink target +JLINK_DEVICE = K32L2B31xxxxA + +# For flash-pyocd target +PYOCD_TARGET = K32L2B + +# flash using pyocd +flash: flash-pyocd diff --git a/hw/bsp/kinetis_k32l/boards/kuiic/kuiic.c b/hw/bsp/kinetis_k32l/boards/kuiic/kuiic.c new file mode 100644 index 000000000..f9002a6d3 --- /dev/null +++ b/hw/bsp/kinetis_k32l/boards/kuiic/kuiic.c @@ -0,0 +1,203 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2018, hathach (tinyusb.org) + * Copyright (c) 2020, Koji Kitayama + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board.h" +#include "board.h" +#include "fsl_smc.h" +#include "fsl_gpio.h" +#include "fsl_port.h" +#include "fsl_clock.h" +#include "fsl_lpuart.h" + +/******************************************************************************* + * Definitions + ******************************************************************************/ +#define SIM_OSC32KSEL_LPO_CLK 3U /*!< OSC32KSEL select: LPO clock */ +#define SOPT5_LPUART1RXSRC_LPUART_RX 0x00u /*!<@brief LPUART1 Receive Data Source Select: LPUART_RX pin */ +#define SOPT5_LPUART1TXSRC_LPUART_TX 0x00u /*!<@brief LPUART1 Transmit Data Source Select: LPUART_TX pin */ +#define BOARD_BOOTCLOCKRUN_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ + +/******************************************************************************* + * Variables + ******************************************************************************/ +/* System clock frequency. */ +// extern uint32_t SystemCoreClock; + +/******************************************************************************* + * Variables for BOARD_BootClockRUN configuration + ******************************************************************************/ +const mcglite_config_t mcgliteConfig_BOARD_BootClockRUN = { + .outSrc = kMCGLITE_ClkSrcHirc, /* MCGOUTCLK source is HIRC */ + .irclkEnableMode = kMCGLITE_IrclkEnable, /* MCGIRCLK enabled, MCGIRCLK disabled in STOP mode */ + .ircs = kMCGLITE_Lirc8M, /* Slow internal reference (LIRC) 8 MHz clock selected */ + .fcrdiv = kMCGLITE_LircDivBy1, /* Low-frequency Internal Reference Clock Divider: divided by 1 */ + .lircDiv2 = kMCGLITE_LircDivBy1, /* Second Low-frequency Internal Reference Clock Divider: divided by 1 */ + .hircEnableInNotHircMode = true, /* HIRC source is enabled */ +}; +const sim_clock_config_t simConfig_BOARD_BootClockRUN = { + .er32kSrc = SIM_OSC32KSEL_LPO_CLK, /* OSC32KSEL select: LPO clock */ + .clkdiv1 = 0x10000U, /* SIM_CLKDIV1 - OUTDIV1: /1, OUTDIV4: /2 */ +}; + +/******************************************************************************* + * Code for BOARD_BootClockRUN configuration + ******************************************************************************/ +void BOARD_BootClockRUN(void) +{ + /* Set the system clock dividers in SIM to safe value. */ + CLOCK_SetSimSafeDivs(); + /* Set MCG to HIRC mode. */ + CLOCK_SetMcgliteConfig(&mcgliteConfig_BOARD_BootClockRUN); + /* Set the clock configuration in SIM module. */ + CLOCK_SetSimConfig(&simConfig_BOARD_BootClockRUN); + /* Set SystemCoreClock variable. */ + SystemCoreClock = BOARD_BOOTCLOCKRUN_CORE_CLOCK; +} + + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB0_IRQHandler(void) +{ + tud_int_handler(0); +} + +void board_init(void) +{ + /* Enable port clocks for GPIO pins */ + CLOCK_EnableClock(kCLOCK_PortA); + CLOCK_EnableClock(kCLOCK_PortB); + CLOCK_EnableClock(kCLOCK_PortC); + CLOCK_EnableClock(kCLOCK_PortD); + CLOCK_EnableClock(kCLOCK_PortE); + + + gpio_pin_config_t led_config = { kGPIO_DigitalOutput, 1 }; + GPIO_PinInit(GPIOA, 1U, &led_config); + PORT_SetPinMux(PORTA, 1U, kPORT_MuxAsGpio); + led_config.outputLogic = 0; + GPIO_PinInit(GPIOA, 2U, &led_config); + PORT_SetPinMux(PORTA, 2U, kPORT_MuxAsGpio); + +#ifdef BUTTON_PIN + gpio_pin_config_t button_config = { kGPIO_DigitalInput, 0 }; + GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); + const port_pin_config_t BUTTON_CFG = { + kPORT_PullUp, + kPORT_FastSlewRate, + kPORT_PassiveFilterDisable, + kPORT_LowDriveStrength, + kPORT_MuxAsGpio + }; + PORT_SetPinConfig(BUTTON_PORT, BUTTON_PIN, &BUTTON_CFG); +#endif + + /* PORTC3 is configured as LPUART0_RX */ + PORT_SetPinMux(PORTC, 3U, kPORT_MuxAlt3); + /* PORTA2 (pin 24) is configured as LPUART0_TX */ + PORT_SetPinMux(PORTE, 0U, kPORT_MuxAlt3); + + SIM->SOPT5 = ((SIM->SOPT5 & + /* Mask bits to zero which are setting */ + (~(SIM_SOPT5_LPUART1TXSRC_MASK | SIM_SOPT5_LPUART1RXSRC_MASK))) + /* LPUART0 Transmit Data Source Select: LPUART0_TX pin. */ + | SIM_SOPT5_LPUART1TXSRC(SOPT5_LPUART1TXSRC_LPUART_TX) + /* LPUART0 Receive Data Source Select: LPUART_RX pin. */ + | SIM_SOPT5_LPUART1RXSRC(SOPT5_LPUART1RXSRC_LPUART_RX)); + + BOARD_BootClockRUN(); + SystemCoreClockUpdate(); + CLOCK_SetLpuart1Clock(1); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#elif CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); +#endif + + lpuart_config_t uart_config; + LPUART_GetDefaultConfig(&uart_config); + uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE; + uart_config.enableTx = true; + uart_config.enableRx = true; + LPUART_Init(UART_PORT, &uart_config, CLOCK_GetFreq(kCLOCK_McgIrc48MClk)); + + // USB + CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcIrc48M, 48000000U); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + if (state) { + LED_GPIO->PDDR |= GPIO_FIT_REG((1UL << LED_PIN)); + } else { + LED_GPIO->PDDR &= GPIO_FIT_REG(~(1UL << LED_PIN)); + } +// GPIO_PinWrite(GPIOA, 1, state ? LED_STATE_ON : (1-LED_STATE_ON) ); +// GPIO_PinWrite(GPIOA, 2, state ? (1-LED_STATE_ON) : LED_STATE_ON ); +} + +uint32_t board_button_read(void) +{ +#ifdef BUTTON_PIN + return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); +#else + return 0; +#endif +} + +int board_uart_read(uint8_t* buf, int len) +{ + LPUART_ReadBlocking(UART_PORT, buf, len); + return len; +} + +int board_uart_write(void const * buf, int len) +{ + LPUART_WriteBlocking(UART_PORT, (uint8_t const*) buf, len); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif diff --git a/hw/bsp/kinetis_k32l/family.mk b/hw/bsp/kinetis_k32l/family.mk new file mode 100644 index 000000000..41f22e250 --- /dev/null +++ b/hw/bsp/kinetis_k32l/family.mk @@ -0,0 +1,32 @@ +SDK_DIR = hw/mcu/nxp/mcux-sdk +DEPS_SUBMODULES += $(SDK_DIR) lib/CMSIS_5 + +MCU_DIR = $(SDK_DIR)/devices/$(MCU) +include $(TOP)/$(BOARD_PATH)/board.mk + +CFLAGS += \ + -mthumb \ + -mabi=aapcs \ + -DCFG_TUSB_MCU=OPT_MCU_KINETIS_K32 + +SRC_C += \ + src/portable/nxp/khci/dcd_khci.c \ + src/portable/nxp/khci/hcd_khci.c \ + $(MCU_DIR)/system_$(MCU).c \ + $(MCU_DIR)/drivers/fsl_clock.c \ + $(SDK_DIR)/drivers/gpio/fsl_gpio.c \ + $(SDK_DIR)/drivers/lpuart/fsl_lpuart.c + +INC += \ + $(TOP)/$(BOARD_PATH) \ + $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ + $(TOP)/$(MCU_DIR) \ + $(TOP)/$(MCU_DIR)/project_template \ + $(TOP)/$(MCU_DIR)/drivers \ + $(TOP)/$(SDK_DIR)/drivers/smc \ + $(TOP)/$(SDK_DIR)/drivers/common \ + $(TOP)/$(SDK_DIR)/drivers/gpio \ + $(TOP)/$(SDK_DIR)/drivers/port \ + $(TOP)/$(SDK_DIR)/drivers/lpuart \ + +SRC_S += $(MCU_DIR)/gcc/startup_$(MCU).S diff --git a/hw/bsp/saml2x/family.mk b/hw/bsp/saml2x/family.mk index 91c2cfa61..98071737a 100644 --- a/hw/bsp/saml2x/family.mk +++ b/hw/bsp/saml2x/family.mk @@ -1,5 +1,5 @@ UF2_FAMILY_ID = 0x68ed2b88 -DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/microchip +DEPS_SUBMODULES += hw/mcu/microchip include $(TOP)/$(BOARD_PATH)/board.mk @@ -32,14 +32,14 @@ SRC_C += \ INC += \ $(TOP)/$(BOARD_PATH) \ - $(TOP)/$(MCU_DIR)/ \ + $(TOP)/$(MCU_DIR) \ + $(TOP)/$(MCU_DIR)/CMSIS/Include \ $(TOP)/$(MCU_DIR)/config \ $(TOP)/$(MCU_DIR)/include \ $(TOP)/$(MCU_DIR)/hal/include \ $(TOP)/$(MCU_DIR)/hal/utils/include \ $(TOP)/$(MCU_DIR)/hpl/port \ $(TOP)/$(MCU_DIR)/hri \ - $(TOP)/lib/CMSIS_5/CMSIS/Core/Include # For freeRTOS port source FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM0 diff --git a/tools/get_deps.py b/tools/get_deps.py index 6db5224a4..4f8c0355c 100644 --- a/tools/get_deps.py +++ b/tools/get_deps.py @@ -169,8 +169,9 @@ deps_optional = { 'ch32v307'], 'lib/CMSIS_5': ['https://github.com/ARM-software/CMSIS_5.git', '20285262657d1b482d132d20d755c8c330d55c1f', - 'imxrt mcx stm32f0 stm32f1 stm32f2 stm32f3 stm32f4 stm32f7 stm32g0 stm32g4 stm32h7 stm32l0 stm32l1 ' - 'stm32l4 stm32l5 stm32u5 stm32wb'], + 'imxrt kinetis_k32l lpc51 lpc54 lpc55 mcx mm32 msp432e4 nrf ra ' + 'stm32f0 stm32f1 stm32f2 stm32f3 stm32f4 stm32f7 stm32g0 stm32g4 ' + 'stm32h7 stm32l0 stm32l1 stm32l4 stm32l5 stm32u5 stm32wb'], 'lib/sct_neopixel': ['https://github.com/gsteiert/sct_neopixel.git', 'e73e04ca63495672d955f9268e003cffe168fcd8', 'lpc55'], -- cgit v1.3.1 From 7ac85d08c7aa59f35cbbf2657dd9be68d46e1fdc Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 26 May 2023 16:37:47 +0700 Subject: move lpc18 and rp2040 to cmake workflow since rp2040 often failed randomly with make --- .github/workflows/build_arm.yml | 3 +- .github/workflows/cmake_arm.yml | 19 ++- hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h | 8 +- hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h | 166 +++++++++++++++++++++ hw/bsp/lpc55/FreeRTOSConfig/FreeRTOSConfig.h | 8 +- hw/bsp/lpc55/boards/double_m33_express/board.cmake | 16 ++ hw/bsp/lpc55/family.cmake | 14 +- hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h | 8 +- hw/bsp/nrf/FreeRTOSConfig/FreeRTOSConfig.h | 166 +++++++++++++++++++++ hw/bsp/saml2x/family.mk | 4 +- src/CMakeLists.txt | 47 ++++-- tools/get_deps.py | 4 +- 12 files changed, 429 insertions(+), 34 deletions(-) create mode 100644 hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h create mode 100644 hw/bsp/lpc55/boards/double_m33_express/board.cmake create mode 100644 hw/bsp/nrf/FreeRTOSConfig/FreeRTOSConfig.h diff --git a/.github/workflows/build_arm.yml b/.github/workflows/build_arm.yml index 8fbaba4c6..42c8eb7ce 100644 --- a/.github/workflows/build_arm.yml +++ b/.github/workflows/build_arm.yml @@ -35,12 +35,11 @@ jobs: # Alphabetical order - 'broadcom_32bit' - 'kinetis_k32l kinetis_kl' - - 'lpc11 lpc13 lpc15 lpc17 lpc18' + - 'lpc11 lpc13 lpc15 lpc17' - 'lpc51 lpc54 lpc55' - 'mm32 msp432e4' - 'nrf' - 'ra' - - 'rp2040' - 'samd11 samd21' - 'samd51 same5x' - 'saml2x' diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index e7991252d..f3989f239 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -32,9 +32,11 @@ jobs: fail-fast: false matrix: family: - # Alphabetical order - - 'mcx' - - 'imxrt' + # Alphabetical order + - 'lpc18' + - 'mcx' + - 'imxrt' + - 'rp2040' steps: - name: Setup Python uses: actions/setup-python@v4 @@ -52,8 +54,19 @@ jobs: - name: Checkout TinyUSB uses: actions/checkout@v3 + - name: Checkout pico-sdk for rp2040 + if: matrix.family == 'rp2040' + uses: actions/checkout@v3 + with: + repository: raspberrypi/pico-sdk + ref: develop + path: pico-sdk + - name: Get Dependencies run: python3 tools/get_deps.py ${{ matrix.family }} - name: Build run: python tools/build_cmake.py ${{ matrix.family }} + env: + # for rp2040, there is no harm if defined for other families + PICO_SDK_PATH: ${{ github.workspace }}/pico-sdk diff --git a/hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h index c8d94f9ed..c1928fbcd 100644 --- a/hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h +++ b/hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h @@ -49,10 +49,10 @@ extern uint32_t SystemCoreClock; #endif /* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 1 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE ( 1024 ) +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) #define configUSE_PREEMPTION 1 #define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 diff --git a/hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h new file mode 100644 index 000000000..323c1a0a4 --- /dev/null +++ b/hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h @@ -0,0 +1,166 @@ +/* + * FreeRTOS Kernel V10.0.0 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. If you wish to use our Amazon + * FreeRTOS name, please do so in a fair use way that does not cause confusion. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + + +#ifndef FREERTOS_CONFIG_H +#define FREERTOS_CONFIG_H + +/*----------------------------------------------------------- + * Application specific definitions. + * + * These definitions should be adjusted for your particular hardware and + * application requirements. + * + * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE + * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. + * + * See http://www.freertos.org/a00110.html. + *----------------------------------------------------------*/ + +// IAR assembler have limited preprocessor support and it only need following macros: +#ifndef __IASMARM__ +// FIXME cause redundant-decls warnings +extern uint32_t SystemCoreClock; +#endif + +/* Cortex M23/M33 port configuration. */ +#define configENABLE_MPU 0 +#define configENABLE_FPU 0 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) + +#define configUSE_PREEMPTION 1 +#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 +#define configCPU_CLOCK_HZ SystemCoreClock +#define configTICK_RATE_HZ ( 1000 ) +#define configMAX_PRIORITIES ( 5 ) +#define configMINIMAL_STACK_SIZE ( 128 ) +#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) +#define configMAX_TASK_NAME_LEN 16 +#define configUSE_16_BIT_TICKS 0 +#define configIDLE_SHOULD_YIELD 1 +#define configUSE_MUTEXES 1 +#define configUSE_RECURSIVE_MUTEXES 1 +#define configUSE_COUNTING_SEMAPHORES 1 +#define configQUEUE_REGISTRY_SIZE 2 +#define configUSE_QUEUE_SETS 0 +#define configUSE_TIME_SLICING 0 +#define configUSE_NEWLIB_REENTRANT 0 +#define configENABLE_BACKWARD_COMPATIBILITY 1 +#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 + +#define configSUPPORT_STATIC_ALLOCATION 0 +#define configSUPPORT_DYNAMIC_ALLOCATION 1 + +/* Hook function related definitions. */ +#define configUSE_IDLE_HOOK 0 +#define configUSE_TICK_HOOK 0 +#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning +#define configCHECK_FOR_STACK_OVERFLOW 2 + +/* Run time and task stats gathering related definitions. */ +#define configGENERATE_RUN_TIME_STATS 0 +#define configRECORD_STACK_HIGH_ADDRESS 1 +#define configUSE_TRACE_FACILITY 1 // legacy trace +#define configUSE_STATS_FORMATTING_FUNCTIONS 0 + +/* Co-routine definitions. */ +#define configUSE_CO_ROUTINES 0 +#define configMAX_CO_ROUTINE_PRIORITIES 2 + +/* Software timer related definitions. */ +#define configUSE_TIMERS 1 +#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) +#define configTIMER_QUEUE_LENGTH 32 +#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE + +/* Optional functions - most linkers will remove unused functions anyway. */ +#define INCLUDE_vTaskPrioritySet 0 +#define INCLUDE_uxTaskPriorityGet 0 +#define INCLUDE_vTaskDelete 0 +#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY +#define INCLUDE_xResumeFromISR 0 +#define INCLUDE_vTaskDelayUntil 1 +#define INCLUDE_vTaskDelay 1 +#define INCLUDE_xTaskGetSchedulerState 0 +#define INCLUDE_xTaskGetCurrentTaskHandle 1 +#define INCLUDE_uxTaskGetStackHighWaterMark 0 +#define INCLUDE_xTaskGetIdleTaskHandle 0 +#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 +#define INCLUDE_pcTaskGetTaskName 0 +#define INCLUDE_eTaskGetState 0 +#define INCLUDE_xEventGroupSetBitFromISR 0 +#define INCLUDE_xTimerPendFunctionCall 0 + +/* Define to trap errors during development. */ +// Halt CPU (breakpoint) when hitting error, only apply for Cortex M3, M4, M7 +#if defined(__ARM_ARCH_7M__) || defined (__ARM_ARCH_7EM__) + #define configASSERT(_exp) \ + do {\ + if ( !(_exp) ) { \ + volatile uint32_t* ARM_CM_DHCSR = ((volatile uint32_t*) 0xE000EDF0UL); /* Cortex M CoreDebug->DHCSR */ \ + if ( (*ARM_CM_DHCSR) & 1UL ) { /* Only halt mcu if debugger is attached */ \ + taskDISABLE_INTERRUPTS(); \ + __asm("BKPT #0\n"); \ + }\ + }\ + } while(0) +#else + #define configASSERT( x ) +#endif + +/* FreeRTOS hooks to NVIC vectors */ +#define xPortPendSVHandler PendSV_Handler +#define xPortSysTickHandler SysTick_Handler +#define vPortSVCHandler SVC_Handler + +//--------------------------------------------------------------------+ +// Interrupt nesting behavior configuration. +//--------------------------------------------------------------------+ + +// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header +#define configPRIO_BITS 3 + +/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1<DHCSR */ \ + if ( (*ARM_CM_DHCSR) & 1UL ) { /* Only halt mcu if debugger is attached */ \ + taskDISABLE_INTERRUPTS(); \ + __asm("BKPT #0\n"); \ + }\ + }\ + } while(0) +#else + #define configASSERT( x ) +#endif + +/* FreeRTOS hooks to NVIC vectors */ +#define xPortPendSVHandler PendSV_Handler +#define xPortSysTickHandler SysTick_Handler +#define vPortSVCHandler SVC_Handler + +//--------------------------------------------------------------------+ +// Interrupt nesting behavior configuration. +//--------------------------------------------------------------------+ + +// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header +#define configPRIO_BITS 3 + +/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1< Date: Fri, 26 May 2023 16:44:29 +0700 Subject: forgot to move hw test --- .github/workflows/build_arm.yml | 75 +---------------------------------------- .github/workflows/cmake_arm.yml | 73 +++++++++++++++++++++++++++++++++++++++ 2 files changed, 74 insertions(+), 74 deletions(-) diff --git a/.github/workflows/build_arm.yml b/.github/workflows/build_arm.yml index 42c8eb7ce..3a2daab08 100644 --- a/.github/workflows/build_arm.yml +++ b/.github/workflows/build_arm.yml @@ -90,24 +90,11 @@ jobs: find ${ex} -name *.map -print -quit | xargs -I % sh -c 'echo "::group::%"; linkermap -v %; echo "::endgroup::"' done - # Upload binaries for rp2040/stm32l412nucleo hardware test with self-hosted - - - name: Prepare rp2040 Artifacts - if: contains(matrix.family, 'rp2040') && github.repository_owner == 'hathach' - run: find examples/ -name "*.elf" -exec mv {} . \; - + # Upload binaries for hardware test with self-hosted - name: Prepare stm32l412nucleo Artifacts if: contains(matrix.family, 'stm32l4') run: find examples/ -path "*stm32l412nucleo/*.elf" -exec mv {} . \; - - name: Upload Artifacts for rp2040 - if: contains(matrix.family,'rp2040') && github.repository_owner == 'hathach' - uses: actions/upload-artifact@v3 - with: - name: rp2040 - path: | - *.elf - - name: Upload Artifacts for stm32l412nucleo if: contains(matrix.family, 'stm32l4') && github.repository_owner == 'hathach' uses: actions/upload-artifact@v3 @@ -116,66 +103,6 @@ jobs: path: | *.elf - # --------------------------------------- - # Hardware in the loop (HIL) - # Current self-hosted instance is running on an RPI4 with - # - pico + pico-probe connected via USB - # - pico-probe is /dev/ttyACM0 - # --------------------------------------- - hw-rp2040-test: - # run only with hathach's commit due to limited resource on RPI4 - if: github.repository_owner == 'hathach' - needs: build-arm - runs-on: [self-hosted, Linux, ARM64, rp2040] - - steps: - - name: Clean workspace - run: | - echo "Cleaning up previous run" - rm -rf "${{ github.workspace }}" - mkdir -p "${{ github.workspace }}" - - - name: Download rp2040 Artifacts - uses: actions/download-artifact@v3 - with: - name: rp2040 - - - name: Create flash.sh - run: | - echo > flash.sh 'cmdout=$(openocd -f "interface/cmsis-dap.cfg" -f "target/rp2040.cfg" -c "adapter speed 5000" -c "program $1 reset exit")' - echo >> flash.sh 'if (( $? )) ; then echo $cmdout ; fi' - chmod +x flash.sh - - - name: Test cdc_dual_ports - run: | - ./flash.sh cdc_dual_ports.elf - while (! ([ -e /dev/ttyACM1 ] && [ -e /dev/ttyACM2 ])) && [ $SECONDS -le 10 ]; do :; done - test -e /dev/ttyACM1 && echo "ttyACM1 exists" - test -e /dev/ttyACM2 && echo "ttyACM2 exists" - - - name: Test cdc_msc - run: | - ./flash.sh cdc_msc.elf - readme='/media/pi/TinyUSB MSC/README.TXT' - while (! ([ -e /dev/ttyACM1 ] && [ -f "$readme" ])) && [ $SECONDS -le 10 ]; do :; done - test -e /dev/ttyACM1 && echo "ttyACM1 exists" - test -f "$readme" && echo "$readme exists" - cat "$readme" - - - name: Test dfu - run: | - ./flash.sh dfu.elf - while (! (dfu-util -l | grep "Found DFU")) && [ $SECONDS -le 10 ]; do :; done - dfu-util -d cafe -a 0 -U dfu0 - dfu-util -d cafe -a 1 -U dfu1 - grep "TinyUSB DFU! - Partition 0" dfu0 - grep "TinyUSB DFU! - Partition 1" dfu1 - - - name: Test dfu_runtime - run: | - ./flash.sh dfu_runtime.elf - while (! (dfu-util -l | grep "Found Runtime")) && [ $SECONDS -le 10 ]; do :; done - # --------------------------------------- # Hardware in the loop (HIL) # Current self-hosted instance is running on an EPYC 7232 server hosted by HiFiPhile user diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index f3989f239..b3f1bd410 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -70,3 +70,76 @@ jobs: env: # for rp2040, there is no harm if defined for other families PICO_SDK_PATH: ${{ github.workspace }}/pico-sdk + + # Upload binaries for hardware test with self-hosted + - name: Prepare rp2040 Artifacts + if: contains(matrix.family, 'rp2040') && github.repository_owner == 'hathach' + run: find examples/ -name "*.elf" -exec mv {} . \; + + - name: Upload Artifacts for rp2040 + if: contains(matrix.family,'rp2040') && github.repository_owner == 'hathach' + uses: actions/upload-artifact@v3 + with: + name: rp2040 + path: | + *.elf + + # --------------------------------------- + # Hardware in the loop (HIL) + # Current self-hosted instance is running on an RPI4 with + # - pico + pico-probe connected via USB + # - pico-probe is /dev/ttyACM0 + # --------------------------------------- + hw-rp2040-test: + # run only with hathach's commit due to limited resource on RPI4 + if: github.repository_owner == 'hathach' + needs: build-arm + runs-on: [self-hosted, Linux, ARM64, rp2040] + + steps: + - name: Clean workspace + run: | + echo "Cleaning up previous run" + rm -rf "${{ github.workspace }}" + mkdir -p "${{ github.workspace }}" + + - name: Download rp2040 Artifacts + uses: actions/download-artifact@v3 + with: + name: rp2040 + + - name: Create flash.sh + run: | + echo > flash.sh 'cmdout=$(openocd -f "interface/cmsis-dap.cfg" -f "target/rp2040.cfg" -c "adapter speed 5000" -c "program $1 reset exit")' + echo >> flash.sh 'if (( $? )) ; then echo $cmdout ; fi' + chmod +x flash.sh + + - name: Test cdc_dual_ports + run: | + ./flash.sh cdc_dual_ports.elf + while (! ([ -e /dev/ttyACM1 ] && [ -e /dev/ttyACM2 ])) && [ $SECONDS -le 10 ]; do :; done + test -e /dev/ttyACM1 && echo "ttyACM1 exists" + test -e /dev/ttyACM2 && echo "ttyACM2 exists" + + - name: Test cdc_msc + run: | + ./flash.sh cdc_msc.elf + readme='/media/pi/TinyUSB MSC/README.TXT' + while (! ([ -e /dev/ttyACM1 ] && [ -f "$readme" ])) && [ $SECONDS -le 10 ]; do :; done + test -e /dev/ttyACM1 && echo "ttyACM1 exists" + test -f "$readme" && echo "$readme exists" + cat "$readme" + + - name: Test dfu + run: | + ./flash.sh dfu.elf + while (! (dfu-util -l | grep "Found DFU")) && [ $SECONDS -le 10 ]; do :; done + dfu-util -d cafe -a 0 -U dfu0 + dfu-util -d cafe -a 1 -U dfu1 + grep "TinyUSB DFU! - Partition 0" dfu0 + grep "TinyUSB DFU! - Partition 1" dfu1 + + - name: Test dfu_runtime + run: | + ./flash.sh dfu_runtime.elf + while (! (dfu-util -l | grep "Found Runtime")) && [ $SECONDS -le 10 ]; do :; done -- cgit v1.3.1 From c88e7481be0a6a55bf8af0a48950892aba05eaee Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 26 May 2023 17:15:54 +0700 Subject: retry hw test --- .github/workflows/cmake_arm.yml | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index b3f1bd410..2070c5061 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -74,7 +74,11 @@ jobs: # Upload binaries for hardware test with self-hosted - name: Prepare rp2040 Artifacts if: contains(matrix.family, 'rp2040') && github.repository_owner == 'hathach' - run: find examples/ -name "*.elf" -exec mv {} . \; + working-directory: ${{github.workspace}}/cmake-build-ci-raspberry_pi_pico + run: | + find device/ -name "*.elf" -exec mv {} . \; + # find host/ -name "*.elf" -exec mv {} . \; + # find dual/ -name "*.elf" -exec mv {} . \; - name: Upload Artifacts for rp2040 if: contains(matrix.family,'rp2040') && github.repository_owner == 'hathach' -- cgit v1.3.1 From 4bd02fb04d52dbd1c2e0f1fe8b18afbd299e46cd Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 26 May 2023 18:54:14 +0700 Subject: more test --- .github/workflows/cmake_arm.yml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index 2070c5061..ed00ee4dc 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -76,6 +76,8 @@ jobs: if: contains(matrix.family, 'rp2040') && github.repository_owner == 'hathach' working-directory: ${{github.workspace}}/cmake-build-ci-raspberry_pi_pico run: | + tree -L 3 + find device/ -name "*.elf" find device/ -name "*.elf" -exec mv {} . \; # find host/ -name "*.elf" -exec mv {} . \; # find dual/ -name "*.elf" -exec mv {} . \; -- cgit v1.3.1 From 59ad5c59dfe1d9dbef033a772d2d5c474c22c53e Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 26 May 2023 18:58:21 +0700 Subject: fix artifacts location --- .github/workflows/cmake_arm.yml | 8 +++----- 1 file changed, 3 insertions(+), 5 deletions(-) diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index ed00ee4dc..ccca0c9be 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -76,11 +76,9 @@ jobs: if: contains(matrix.family, 'rp2040') && github.repository_owner == 'hathach' working-directory: ${{github.workspace}}/cmake-build-ci-raspberry_pi_pico run: | - tree -L 3 - find device/ -name "*.elf" - find device/ -name "*.elf" -exec mv {} . \; - # find host/ -name "*.elf" -exec mv {} . \; - # find dual/ -name "*.elf" -exec mv {} . \; + find device/ -name "*.elf" -exec mv {} ../ \; + # find host/ -name "*.elf" -exec mv {} ../ \; + # find dual/ -name "*.elf" -exec mv {} ../ \; - name: Upload Artifacts for rp2040 if: contains(matrix.family,'rp2040') && github.repository_owner == 'hathach' -- cgit v1.3.1