From ba9c774a2a5f784a85de1ca1212268b367046c03 Mon Sep 17 00:00:00 2001 From: hathach Date: Sat, 23 May 2020 13:29:30 +0700 Subject: board test work fine --- hw/bsp/stm32h743eval/STM32H743XIHx_FLASH.ld | 173 ++++++++++ hw/bsp/stm32h743eval/board.mk | 47 +++ hw/bsp/stm32h743eval/stm32h743eval.c | 274 ++++++++++++++++ hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h | 480 ++++++++++++++++++++++++++++ 4 files changed, 974 insertions(+) create mode 100644 hw/bsp/stm32h743eval/STM32H743XIHx_FLASH.ld create mode 100644 hw/bsp/stm32h743eval/board.mk create mode 100644 hw/bsp/stm32h743eval/stm32h743eval.c create mode 100644 hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h743eval/STM32H743XIHx_FLASH.ld b/hw/bsp/stm32h743eval/STM32H743XIHx_FLASH.ld new file mode 100644 index 000000000..59b9ff4df --- /dev/null +++ b/hw/bsp/stm32h743eval/STM32H743XIHx_FLASH.ld @@ -0,0 +1,173 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32H743XIHx Device with +** 2048KByte FLASH, 128KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20020000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +DTCMRAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K +RAM_D1 (xrw) : ORIGIN = 0x24000000, LENGTH = 512K +RAM_D2 (xrw) : ORIGIN = 0x30000000, LENGTH = 288K +RAM_D3 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K +ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 2048K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >DTCMRAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >DTCMRAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >DTCMRAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} + + diff --git a/hw/bsp/stm32h743eval/board.mk b/hw/bsp/stm32h743eval/board.mk new file mode 100644 index 000000000..549249d24 --- /dev/null +++ b/hw/bsp/stm32h743eval/board.mk @@ -0,0 +1,47 @@ +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m7 \ + -mfloat-abi=hard \ + -mfpu=fpv5-d16 \ + -nostdlib -nostartfiles \ + -DSTM32H743xx \ + -DCFG_TUSB_MCU=OPT_MCU_STM32H7 + +# suppress warning caused by vendor mcu driver +CFLAGS += -Wno-error=maybe-uninitialized + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32H7xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32H7xx + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/STM32H743XIHx_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32h7xx.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_pwr_ex.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h743xx.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = synopsys + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM7/r0p1 + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32h743eval/stm32h743eval.c b/hw/bsp/stm32h743eval/stm32h743eval.c new file mode 100644 index 000000000..ef9d575ac --- /dev/null +++ b/hw/bsp/stm32h743eval/stm32h743eval.c @@ -0,0 +1,274 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 William D. Jones (thor0505@comcast.net), + * Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32h7xx_hal.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void OTG_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PORT GPIOA +#define LED_PIN GPIO_PIN_4 +#define LED_STATE_ON 1 + +// Tamper push-button +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 +#define BUTTON_STATE_ACTIVE 0 + +// enable all LED, Button, Uart, USB clock +static void all_rcc_clk_enable(void) +{ + __HAL_RCC_GPIOA_CLK_ENABLE(); // LED, USB D+, D- + __HAL_RCC_GPIOC_CLK_ENABLE(); // Button +// __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx +// __HAL_RCC_USART3_CLK_ENABLE(); // Uart module +} + +/* PWR, RCC, GPIO (All): AHB4 (D3 domain) + USB{1,2} OTG_{H,F}S: AHB1 (D2 domain) +*/ + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSE) + * SYSCLK(Hz) = 400000000 (CPU Clock) + * HCLK(Hz) = 200000000 (AXI and AHBs Clock) + * AHB Prescaler = 2 + * D1 APB3 Prescaler = 2 (APB3 Clock 100MHz) + * D2 APB1 Prescaler = 2 (APB1 Clock 100MHz) + * D2 APB2 Prescaler = 2 (APB2 Clock 100MHz) + * D3 APB4 Prescaler = 2 (APB4 Clock 100MHz) + * HSE Frequency(Hz) = 25000000 + * PLL_M = 5 + * PLL_N = 160 + * PLL_P = 2 + * PLL_Q = 4 + * PLL_R = 2 + * PLL3_M = 25 + * PLL3_N = 336 + * PLL3_P = 2 + * PLL3_Q = 7 + * PLL3_R = 2 + * VDD(V) = 3.3 + * Flash Latency(WS) = 4 + * @param None + * @retval None + */ + +void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_PeriphCLKInitTypeDef PeriphClkInitStruct; + + /*!< Supply configuration update enable */ + HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY); + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + while ((PWR->D3CR & (PWR_D3CR_VOSRDY)) != PWR_D3CR_VOSRDY) {} + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.HSIState = RCC_HSI_OFF; + RCC_OscInitStruct.CSIState = RCC_CSI_OFF; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + + /* PLL1 for System Clock */ + RCC_OscInitStruct.PLL.PLLM = 5; + RCC_OscInitStruct.PLL.PLLN = 160; + RCC_OscInitStruct.PLL.PLLFRACN = 0; + RCC_OscInitStruct.PLL.PLLP = 2; + RCC_OscInitStruct.PLL.PLLR = 2; + RCC_OscInitStruct.PLL.PLLQ = 4; + + RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOMEDIUM; + RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* PLL3 for USB Clock */ + PeriphClkInitStruct.PLL3.PLL3M = 25; + PeriphClkInitStruct.PLL3.PLL3N = 336; + PeriphClkInitStruct.PLL3.PLL3FRACN = 0; + PeriphClkInitStruct.PLL3.PLL3P = 2; + PeriphClkInitStruct.PLL3.PLL3R = 2; + PeriphClkInitStruct.PLL3.PLL3Q = 7; + + PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB; + PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL3; + HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); + + /* Select PLL as system clock source and configure bus clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_D1PCLK1 | RCC_CLOCKTYPE_PCLK1 | \ + RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_D3PCLK1); + + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2; + RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2; + RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV1; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4); + + /*activate CSI clock mondatory for I/O Compensation Cell*/ + __HAL_RCC_CSI_ENABLE() ; + + /* Enable SYSCFG clock mondatory for I/O Compensation Cell */ + __HAL_RCC_SYSCFG_CLK_ENABLE() ; + + /* Enables the I/O Compensation Cell */ + HAL_EnableCompensationCell(); +} + +void board_init(void) +{ + SystemClock_Config(); + all_rcc_clk_enable(); + + #if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + #endif + + GPIO_InitTypeDef GPIO_InitStruct; + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // USB Pin Init + // PA9- VUSB, PA10- ID, PA11- DM, PA12- DP + + /* Configure DM DP Pins */ + GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure VBUS Pin */ + GPIO_InitStruct.Pin = GPIO_PIN_9; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* This for ID line debug */ + GPIO_InitStruct.Pin = GPIO_PIN_10; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + // https://community.st.com/s/question/0D50X00009XkYZLSA3/stm32h7-nucleo-usb-fs-cdc + // TODO: Board init actually works fine without this line. + HAL_PWREx_EnableUSBVoltageDetector(); + __HAL_RCC_USB2_OTG_FS_CLK_ENABLE(); + + // Enable VBUS sense (B device) via pin PA9 + USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + return (BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN)) ? 1 : 0; +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + (void) buf; (void) len; + return 0; +} + + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h b/hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h new file mode 100644 index 000000000..2a9eb37ae --- /dev/null +++ b/hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h @@ -0,0 +1,480 @@ +/** + ****************************************************************************** + * @file stm32h7xx_hal_conf_template.h + * @brief HAL configuration template file. + * This file should be copied to the application folder and renamed + * to stm32h7xx_hal_conf.h. + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2019 STMicroelectronics

+ * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32H7xx_HAL_CONF_H +#define __STM32H7xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_COMP_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_DCMI_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +/* #define HAL_EXTI_MODULE_ENABLED */ +/* #define HAL_FDCAN_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_HASH_MODULE_ENABLED */ +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_HRTIM_MODULE_ENABLED */ +/* #define HAL_HSEM_MODULE_ENABLED */ +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_JPEG_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_LTDC_MODULE_ENABLED */ +/* #define HAL_MDIOS_MODULE_ENABLED */ +/* #define HAL_MDMA_MODULE_ENABLED */ +/* #define HAL_MMC_MODULE_ENABLED */ +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_OPAMP_MODULE_ENABLED */ +/* #define HAL_PCD_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +/* #define HAL_RAMECC_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SAI_MODULE_ENABLED */ +/* #define HAL_SD_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_SMBUS_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +#define HAL_SPI_MODULE_ENABLED +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SWPMI_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +/* #define HAL_UART_MODULE_ENABLED */ +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) +#define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal oscillator (CSI) default value. + * This value is the default CSI value after Reset. + */ +#if !defined (CSI_VALUE) + #define CSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* CSI_VALUE */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)64000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature.*/ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External clock in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x0F) /*!< tick interrupt priority */ +#define USE_RTOS 0 +#define USE_SD_TRANSCEIVER 1U /*!< use uSD Transceiver */ +#define USE_SPI_CRC 1U /*!< use CRC in SPI */ + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_COMP_REGISTER_CALLBACKS 0U /* COMP register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_FDCAN_REGISTER_CALLBACKS 0U /* FDCAN register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_HRTIM_REGISTER_CALLBACKS 0U /* HRTIM register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIO register callback disabled */ +#define USE_HAL_OPAMP_REGISTER_CALLBACKS 0U /* MDIO register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_SWPMI_REGISTER_CALLBACKS 0U /* SWPMI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################### Ethernet Configuration ######################### */ +#define ETH_TX_DESC_CNT 4 /* number of Ethernet Tx DMA descriptors */ +#define ETH_RX_DESC_CNT 4 /* number of Ethernet Rx DMA descriptors */ + +#define ETH_MAC_ADDR0 ((uint8_t)0x02) +#define ETH_MAC_ADDR1 ((uint8_t)0x00) +#define ETH_MAC_ADDR2 ((uint8_t)0x00) +#define ETH_MAC_ADDR3 ((uint8_t)0x00) +#define ETH_MAC_ADDR4 ((uint8_t)0x00) +#define ETH_MAC_ADDR5 ((uint8_t)0x00) + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32h7xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32h7xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32h7xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_MDMA_MODULE_ENABLED + #include "stm32h7xx_hal_mdma.h" +#endif /* HAL_MDMA_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32h7xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32h7xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32h7xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32h7xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32h7xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32h7xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED + #include "stm32h7xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32h7xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32h7xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_FDCAN_MODULE_ENABLED + #include "stm32h7xx_hal_fdcan.h" +#endif /* HAL_FDCAN_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32h7xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED + #include "stm32h7xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32h7xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32h7xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32h7xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32h7xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_HRTIM_MODULE_ENABLED + #include "stm32h7xx_hal_hrtim.h" +#endif /* HAL_HRTIM_MODULE_ENABLED */ + +#ifdef HAL_HSEM_MODULE_ENABLED + #include "stm32h7xx_hal_hsem.h" +#endif /* HAL_HSEM_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32h7xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32h7xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32h7xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32h7xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32h7xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32h7xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_JPEG_MODULE_ENABLED + #include "stm32h7xx_hal_jpeg.h" +#endif /* HAL_JPEG_MODULE_ENABLED */ + +#ifdef HAL_MDIOS_MODULE_ENABLED + #include "stm32h7xx_hal_mdios.h" +#endif /* HAL_MDIOS_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED + #include "stm32h7xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32h7xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED +#include "stm32h7xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_OPAMP_MODULE_ENABLED +#include "stm32h7xx_hal_opamp.h" +#endif /* HAL_OPAMP_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32h7xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32h7xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RAMECC_MODULE_ENABLED + #include "stm32h7xx_hal_ramecc.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32h7xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32h7xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32h7xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32h7xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32h7xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32h7xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32h7xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_SWPMI_MODULE_ENABLED + #include "stm32h7xx_hal_swpmi.h" +#endif /* HAL_SWPMI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32h7xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32h7xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32h7xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32h7xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32h7xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32h7xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32h7xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32h7xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32h7xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t *file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32H7xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit v1.3.1 From 62a746bdc7dc677cabeba9ef6f1dd974de1c0791 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 26 May 2020 12:18:18 +0700 Subject: wip --- hw/bsp/stm32h743eval/board.mk | 7 ++++++- hw/bsp/stm32h743eval/stm32h743eval.c | 13 +++++++++++-- 2 files changed, 17 insertions(+), 3 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h743eval/board.mk b/hw/bsp/stm32h743eval/board.mk index 549249d24..5044cdc08 100644 --- a/hw/bsp/stm32h743eval/board.mk +++ b/hw/bsp/stm32h743eval/board.mk @@ -7,7 +7,12 @@ CFLAGS += \ -mfpu=fpv5-d16 \ -nostdlib -nostartfiles \ -DSTM32H743xx \ - -DCFG_TUSB_MCU=OPT_MCU_STM32H7 + -DCFG_TUSB_MCU=OPT_MCU_STM32H7 \ + +# Board specific for using usb ports +CFLAGS += \ + -DCFG_BOARD_DEVICE_RHPORT_NUM=1 \ + -DCFG_BOARD_DEVICE_RHPORT_HIGHSPEED # suppress warning caused by vendor mcu driver CFLAGS += -Wno-error=maybe-uninitialized diff --git a/hw/bsp/stm32h743eval/stm32h743eval.c b/hw/bsp/stm32h743eval/stm32h743eval.c index ef9d575ac..5a7934ea2 100644 --- a/hw/bsp/stm32h743eval/stm32h743eval.c +++ b/hw/bsp/stm32h743eval/stm32h743eval.c @@ -187,8 +187,16 @@ void board_init(void) GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); - // USB Pin Init - // PA9- VUSB, PA10- ID, PA11- DM, PA12- DP +#if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE + + // USB1 HS (ULPI Phy), internal FS PHY + // PB12 ID, PB13 VBUS, PB14 DM, PB15 DP + +#endif + +#if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE + // USB2 FS Pin Init + // PA9 VUSB, PA10 ID, PA11 DM, PA12 DP /* Configure DM DP Pins */ GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12; @@ -219,6 +227,7 @@ void board_init(void) // Enable VBUS sense (B device) via pin PA9 USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; +#endif } //--------------------------------------------------------------------+ -- cgit v1.3.1 From fad088719e7cc4d1cab9216eb81567dd67af65f7 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 26 May 2020 15:21:23 +0700 Subject: merge CFG_TUSB_RHPORT1_MODE into CFG_TUSB_RHPORT0_MODE each port is 1 byte for easy maintenance --- examples/device/cdc_msc/src/tusb_config.h | 25 +++++++++++----- hw/bsp/ea4357/ea4357.c | 8 ++--- hw/bsp/mcb1800/mcb1800.c | 8 ++--- hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c | 4 +-- hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c | 4 +-- hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c | 4 +-- hw/bsp/ngx4330/ngx4330.c | 8 ++--- hw/bsp/teensy_40/teensy40.c | 4 +-- src/tusb_option.h | 50 +++++++++++++++++-------------- 9 files changed, 66 insertions(+), 49 deletions(-) (limited to 'hw/bsp') diff --git a/examples/device/cdc_msc/src/tusb_config.h b/examples/device/cdc_msc/src/tusb_config.h index 09e98b247..9beb9f6a2 100644 --- a/examples/device/cdc_msc/src/tusb_config.h +++ b/examples/device/cdc_msc/src/tusb_config.h @@ -34,19 +34,30 @@ // COMMON CONFIGURATION //-------------------------------------------------------------------- -// defined by compiler flags for flexibility +// defined by board.mk #ifndef CFG_TUSB_MCU #error CFG_TUSB_MCU must be defined #endif -#if CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX || \ - CFG_TUSB_MCU == OPT_MCU_NUC505 || CFG_TUSB_MCU == OPT_MCU_CXD56 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | OPT_MODE_HIGH_SPEED) -#else - #define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE +// RHPort number used for device can be defined by board.mk, default to port 0 +#ifndef BOARD_DEVICE_RHPORT_NUM + #define BOARD_DEVICE_RHPORT_NUM 0 #endif -#define CFG_TUSB_OS OPT_OS_NONE +// RHPort max operational speed can defined by board.mk +// Default to Highspeed for MCU with internal HighSpeed PHY (can be port specific), otherwise FullSpeed +#ifndef BOARD_DEVICE_RHPORT_SPEED + #if (CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX || \ + CFG_TUSB_MCU == OPT_MCU_NUC505 || CFG_TUSB_MCU == OPT_MCU_CXD56) + #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_HIGH_SPEED + #else + #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_FULL_SPEED + #endif +#endif + +// Device mode with rhport and speed defined by board.mk +#define CFG_TUSB_RHPORT0_MODE ((OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) << (8*BOARD_DEVICE_RHPORT_NUM)) +#define CFG_TUSB_OS OPT_OS_NONE // CFG_TUSB_DEBUG is defined by compiler in DEBUG build // #define CFG_TUSB_DEBUG 0 diff --git a/hw/bsp/ea4357/ea4357.c b/hw/bsp/ea4357/ea4357.c index b7e7f7a5c..04c4e60a6 100644 --- a/hw/bsp/ea4357/ea4357.c +++ b/hw/bsp/ea4357/ea4357.c @@ -149,7 +149,7 @@ void board_init(void) * status feedback from the distribution switch. GPIO54 is used for VBUS sensing. 15Kohm pull-down * resistors are always active */ -#if CFG_TUSB_RHPORT0_MODE +#if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE | OPT_MODE_HOST) Chip_USB0_Init(); // // Reset controller @@ -185,7 +185,7 @@ void board_init(void) * of VBUS can be read via U31. * JP16 shall not be inserted. */ -#if CFG_TUSB_RHPORT1_MODE +#if CFG_TUSB_RHPORT0_MODE & ((OPT_MODE_DEVICE | OPT_MODE_HOST) << 8) Chip_USB1_Init(); // // Reset controller @@ -232,11 +232,11 @@ void USB0_IRQHandler(void) void USB1_IRQHandler(void) { - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) tuh_isr(1); #endif - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) tud_int_handler(1); #endif } diff --git a/hw/bsp/mcb1800/mcb1800.c b/hw/bsp/mcb1800/mcb1800.c index ae9f1b62f..6387f983e 100644 --- a/hw/bsp/mcb1800/mcb1800.c +++ b/hw/bsp/mcb1800/mcb1800.c @@ -43,11 +43,11 @@ void USB0_IRQHandler(void) void USB1_IRQHandler(void) { - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) tuh_isr(1); #endif - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) tud_int_handler(1); #endif } @@ -163,7 +163,7 @@ void board_init(void) }; // USB0 -#if CFG_TUSB_RHPORT0_MODE +#if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE | OPT_MODE_HOST) Chip_USB0_Init(); // // Reset controller @@ -180,7 +180,7 @@ void board_init(void) #endif // USB1 -#if CFG_TUSB_RHPORT1_MODE +#if CFG_TUSB_RHPORT0_MODE & ((OPT_MODE_DEVICE | OPT_MODE_HOST) << 8) Chip_USB1_Init(); // // Reset controller diff --git a/hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c b/hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c index be0ae3ea8..8dae7a0c2 100644 --- a/hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c +++ b/hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c @@ -134,11 +134,11 @@ void USB_OTG1_IRQHandler(void) void USB_OTG2_IRQHandler(void) { - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) tuh_isr(1); #endif - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) tud_int_handler(1); #endif } diff --git a/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c b/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c index be0ae3ea8..8dae7a0c2 100644 --- a/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c +++ b/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c @@ -134,11 +134,11 @@ void USB_OTG1_IRQHandler(void) void USB_OTG2_IRQHandler(void) { - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) tuh_isr(1); #endif - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) tud_int_handler(1); #endif } diff --git a/hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c b/hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c index be0ae3ea8..8dae7a0c2 100644 --- a/hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c +++ b/hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c @@ -134,11 +134,11 @@ void USB_OTG1_IRQHandler(void) void USB_OTG2_IRQHandler(void) { - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) tuh_isr(1); #endif - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) tud_int_handler(1); #endif } diff --git a/hw/bsp/ngx4330/ngx4330.c b/hw/bsp/ngx4330/ngx4330.c index 5296ddcb3..85d11d6ad 100644 --- a/hw/bsp/ngx4330/ngx4330.c +++ b/hw/bsp/ngx4330/ngx4330.c @@ -161,7 +161,7 @@ void board_init(void) * status feedback from the distribution switch. GPIO54 is used for VBUS sensing. 15Kohm pull-down * resistors are always active */ -#if CFG_TUSB_RHPORT0_MODE +#if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE | OPT_MODE_HOST) Chip_USB0_Init(); // // Reset controller @@ -197,7 +197,7 @@ void board_init(void) * of VBUS can be read via U31. * JP16 shall not be inserted. */ -#if CFG_TUSB_RHPORT1_MODE +#if CFG_TUSB_RHPORT0_MODE & ((OPT_MODE_DEVICE | OPT_MODE_HOST) << 8) Chip_USB1_Init(); // // Reset controller @@ -235,11 +235,11 @@ void USB0_IRQHandler(void) void USB1_IRQHandler(void) { - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) tuh_isr(1); #endif - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) tud_int_handler(1); #endif } diff --git a/hw/bsp/teensy_40/teensy40.c b/hw/bsp/teensy_40/teensy40.c index f45a98ef3..0ca86f602 100644 --- a/hw/bsp/teensy_40/teensy40.c +++ b/hw/bsp/teensy_40/teensy40.c @@ -135,11 +135,11 @@ void USB_OTG1_IRQHandler(void) void USB_OTG2_IRQHandler(void) { - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) tuh_isr(1); #endif - #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE + #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) tud_int_handler(1); #endif } diff --git a/src/tusb_option.h b/src/tusb_option.h index 9e6a2b532..472656424 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -114,44 +114,50 @@ /** \addtogroup group_configuration * @{ */ + //-------------------------------------------------------------------- -// CONTROLLER -// Only 1 roothub port can be configured to be device and/or host. -// tinyusb does not support dual devices or dual host configuration +// RootHub Mode Configuration +// +// Each byte of the CFG_TUSB_RHPORTx_MODE contains operation mode for +// a roothub port (device or host). Therefore each macro can have up to +// 4 ports. //-------------------------------------------------------------------- -/** \defgroup group_mode Controller Mode Selection - * \brief CFG_TUSB_CONTROLLER_N_MODE must be defined with these - * @{ */ + +// Lower 4-bit is operational mode #define OPT_MODE_NONE 0x00 ///< Disabled #define OPT_MODE_DEVICE 0x01 ///< Device Mode #define OPT_MODE_HOST 0x02 ///< Host Mode -#define OPT_MODE_HIGH_SPEED 0x10 ///< High speed -/** @} */ + +// Higher 4-bit is max operational speed (corresponding to tusb_speed_t) +#define OPT_MODE_FULL_SPEED 0x00 ///< Max Full Speed +#define OPT_MODE_LOW_SPEED 0x10 ///< Max Low Speed +#define OPT_MODE_HIGH_SPEED 0x20 ///< Max High Speed + #ifndef CFG_TUSB_RHPORT0_MODE #define CFG_TUSB_RHPORT0_MODE OPT_MODE_NONE #endif -#ifndef CFG_TUSB_RHPORT1_MODE - #define CFG_TUSB_RHPORT1_MODE OPT_MODE_NONE -#endif +//#ifndef CFG_TUSB_RHPORT1_MODE +// #define CFG_TUSB_RHPORT1_MODE OPT_MODE_NONE +//#endif -#if ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST) && (CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST)) || \ - ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) && (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE)) - #error "tinyusb does not support same modes on more than 1 roothub port" +#if ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST ) && (CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)) ) || \ + ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) && (CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)) ) + #error "TinyUSB currently does not support same modes on more than 1 roothub port" #endif // Which roothub port is configured as host -#define TUH_OPT_RHPORT ( (CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST) ? 0 : ((CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST) ? 1 : -1) ) +#define TUH_OPT_RHPORT ( (CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST) ? 0 : ((CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)) ? 1 : -1) ) #define TUSB_OPT_HOST_ENABLED ( TUH_OPT_RHPORT >= 0 ) // Which roothub port is configured as device -#define TUD_OPT_RHPORT ( (CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) ? 0 : ((CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) ? 1 : -1) ) +#define TUD_OPT_RHPORT ( (CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) ? 0 : ((CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)) ? 1 : -1) ) #if TUD_OPT_RHPORT == 0 -#define TUD_OPT_HIGH_SPEED ( CFG_TUSB_RHPORT0_MODE & OPT_MODE_HIGH_SPEED ) + #define TUD_OPT_HIGH_SPEED ( CFG_TUSB_RHPORT0_MODE & OPT_MODE_HIGH_SPEED ) #else -#define TUD_OPT_HIGH_SPEED ( CFG_TUSB_RHPORT1_MODE & OPT_MODE_HIGH_SPEED ) + #define TUD_OPT_HIGH_SPEED ( CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HIGH_SPEED << 8) ) #endif #define TUSB_OPT_DEVICE_ENABLED ( TUD_OPT_RHPORT >= 0 ) @@ -168,15 +174,15 @@ // place data in accessible RAM for usb controller #ifndef CFG_TUSB_MEM_SECTION -#define CFG_TUSB_MEM_SECTION + #define CFG_TUSB_MEM_SECTION #endif #ifndef CFG_TUSB_MEM_ALIGN -#define CFG_TUSB_MEM_ALIGN TU_ATTR_ALIGNED(4) + #define CFG_TUSB_MEM_ALIGN TU_ATTR_ALIGNED(4) #endif #ifndef CFG_TUSB_OS -#define CFG_TUSB_OS OPT_OS_NONE + #define CFG_TUSB_OS OPT_OS_NONE #endif //-------------------------------------------------------------------- @@ -184,7 +190,7 @@ //-------------------------------------------------------------------- #ifndef CFG_TUD_ENDPOINT0_SIZE - #define CFG_TUD_ENDPOINT0_SIZE 64 + #define CFG_TUD_ENDPOINT0_SIZE 64 #endif #ifndef CFG_TUD_CDC -- cgit v1.3.1 From 0482f0d6867835d3dbb3939452fbcfaf9727b555 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 26 May 2020 22:11:26 +0700 Subject: update h743eval with rhport=1 highspeed --- hw/bsp/stm32h743eval/board.mk | 7 +-- hw/bsp/stm32h743eval/stm32h743eval.c | 97 ++++++++++++++++++++++++++++++++---- src/tusb_option.h | 4 -- test/test/support/tusb_config.h | 5 -- 4 files changed, 89 insertions(+), 24 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h743eval/board.mk b/hw/bsp/stm32h743eval/board.mk index 5044cdc08..68d142435 100644 --- a/hw/bsp/stm32h743eval/board.mk +++ b/hw/bsp/stm32h743eval/board.mk @@ -8,11 +8,8 @@ CFLAGS += \ -nostdlib -nostartfiles \ -DSTM32H743xx \ -DCFG_TUSB_MCU=OPT_MCU_STM32H7 \ - -# Board specific for using usb ports -CFLAGS += \ - -DCFG_BOARD_DEVICE_RHPORT_NUM=1 \ - -DCFG_BOARD_DEVICE_RHPORT_HIGHSPEED + -DBOARD_DEVICE_RHPORT_NUM=1 \ + -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED # suppress warning caused by vendor mcu driver CFLAGS += -Wno-error=maybe-uninitialized diff --git a/hw/bsp/stm32h743eval/stm32h743eval.c b/hw/bsp/stm32h743eval/stm32h743eval.c index 5a7934ea2..fd3d33047 100644 --- a/hw/bsp/stm32h743eval/stm32h743eval.c +++ b/hw/bsp/stm32h743eval/stm32h743eval.c @@ -32,11 +32,22 @@ //--------------------------------------------------------------------+ // Forward USB interrupt events to TinyUSB IRQ Handler //--------------------------------------------------------------------+ + +// Despite being call USB2_OTG +// OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port void OTG_FS_IRQHandler(void) { tud_int_handler(0); } +// Despite being call USB2_OTG +// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port +void OTG_HS_IRQHandler(void) +{ + tud_int_handler(1); +} + + //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM //--------------------------------------------------------------------+ @@ -53,7 +64,7 @@ void OTG_FS_IRQHandler(void) // enable all LED, Button, Uart, USB clock static void all_rcc_clk_enable(void) { - __HAL_RCC_GPIOA_CLK_ENABLE(); // LED, USB D+, D- + __HAL_RCC_GPIOA_CLK_ENABLE(); // LED __HAL_RCC_GPIOC_CLK_ENABLE(); // Button // __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx // __HAL_RCC_USART3_CLK_ENABLE(); // Uart module @@ -187,17 +198,13 @@ void board_init(void) GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); -#if CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE - - // USB1 HS (ULPI Phy), internal FS PHY - // PB12 ID, PB13 VBUS, PB14 DM, PB15 DP - -#endif - -#if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE - // USB2 FS Pin Init +#if BOARD_DEVICE_RHPORT_NUM == 0 + // Despite being call USB2_OTG + // OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port // PA9 VUSB, PA10 ID, PA11 DM, PA12 DP + __HAL_RCC_GPIOA_CLK_ENABLE(); + /* Configure DM DP Pins */ GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; @@ -228,6 +235,76 @@ void board_init(void) // Enable VBUS sense (B device) via pin PA9 USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; #endif + +#if BOARD_DEVICE_RHPORT_NUM == 1 + // Despite being call USB2_OTG + // OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port + __GPIOA_CLK_ENABLE(); + __GPIOB_CLK_ENABLE(); + __GPIOC_CLK_ENABLE(); + __GPIOH_CLK_ENABLE(); + __GPIOI_CLK_ENABLE(); + + /* CLK */ + GPIO_InitStruct.Pin = GPIO_PIN_5; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* D0 */ + GPIO_InitStruct.Pin = GPIO_PIN_3; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* D1 D2 D3 D4 D5 D6 D7 */ + GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_5 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + /* STP */ + GPIO_InitStruct.Pin = GPIO_PIN_0; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + + /* NXT */ + GPIO_InitStruct.Pin = GPIO_PIN_4; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOH, &GPIO_InitStruct); + + /* DIR */ + GPIO_InitStruct.Pin = GPIO_PIN_11; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOI, &GPIO_InitStruct); + __HAL_RCC_USB1_OTG_HS_ULPI_CLK_ENABLE(); + + /* Enable USB HS Clocks */ + __HAL_RCC_USB1_OTG_HS_CLK_ENABLE(); + + // No VBUS sense + USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // Force device mode + // USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; + // USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; + + // B-peripheral session valid override enabl +// USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; +// USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; +#endif // rhport = 1 + } //--------------------------------------------------------------------+ diff --git a/src/tusb_option.h b/src/tusb_option.h index 472656424..c251d578a 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -138,10 +138,6 @@ #define CFG_TUSB_RHPORT0_MODE OPT_MODE_NONE #endif -//#ifndef CFG_TUSB_RHPORT1_MODE -// #define CFG_TUSB_RHPORT1_MODE OPT_MODE_NONE -//#endif - #if ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST ) && (CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)) ) || \ ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) && (CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)) ) #error "TinyUSB currently does not support same modes on more than 1 roothub port" diff --git a/test/test/support/tusb_config.h b/test/test/support/tusb_config.h index 5258513ec..76f975323 100644 --- a/test/test/support/tusb_config.h +++ b/test/test/support/tusb_config.h @@ -43,12 +43,7 @@ #define CFG_TUSB_MCU OPT_MCU_NRF5X #endif -#if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | OPT_MODE_HIGH_SPEED) -#else -#define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE -#endif - #define CFG_TUSB_OS OPT_OS_NONE // CFG_TUSB_DEBUG is defined by compiler in DEBUG build -- cgit v1.3.1 From 227bffe04b5d61e49a6f7e777c12e1efd7b498d1 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 27 May 2020 01:14:52 +0700 Subject: adding h743 uart, but not enabled yet since it conflict with OTG_FS2 --- hw/bsp/stm32h743eval/board.mk | 7 ++++++- hw/bsp/stm32h743eval/stm32h743eval.c | 35 ++++++++++++++++++++++++++++--- hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h | 4 +++- 3 files changed, 41 insertions(+), 5 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h743eval/board.mk b/hw/bsp/stm32h743eval/board.mk index 68d142435..5c6c6ea4f 100644 --- a/hw/bsp/stm32h743eval/board.mk +++ b/hw/bsp/stm32h743eval/board.mk @@ -12,7 +12,7 @@ CFLAGS += \ -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED # suppress warning caused by vendor mcu driver -CFLAGS += -Wno-error=maybe-uninitialized +CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32H7xx_HAL_Driver ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32H7xx @@ -27,6 +27,7 @@ SRC_C += \ $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc.c \ $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc_ex.c \ $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_uart.c \ $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_pwr_ex.c SRC_S += \ @@ -45,5 +46,9 @@ CHIP_FAMILY = synopsys # For freeRTOS port source FREERTOS_PORT = ARM_CM7/r0p1 +# For flash-jlink target +JLINK_DEVICE = stm32h743xi +JLINK_IF = jtag + # flash target using on-board stlink flash: flash-stlink diff --git a/hw/bsp/stm32h743eval/stm32h743eval.c b/hw/bsp/stm32h743eval/stm32h743eval.c index fd3d33047..d149c1230 100644 --- a/hw/bsp/stm32h743eval/stm32h743eval.c +++ b/hw/bsp/stm32h743eval/stm32h743eval.c @@ -61,13 +61,21 @@ void OTG_HS_IRQHandler(void) #define BUTTON_PIN GPIO_PIN_13 #define BUTTON_STATE_ACTIVE 0 +#define UARTx USART1 +#define UART_GPIO_PORT GPIOB +#define UART_GPIO_AF GPIO_AF4_USART1 +#define UART_TX_PIN GPIO_PIN_14 +#define UART_RX_PIN GPIO_PIN_15 + +UART_HandleTypeDef UartHandle; + // enable all LED, Button, Uart, USB clock static void all_rcc_clk_enable(void) { __HAL_RCC_GPIOA_CLK_ENABLE(); // LED __HAL_RCC_GPIOC_CLK_ENABLE(); // Button -// __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx -// __HAL_RCC_USART3_CLK_ENABLE(); // Uart module +// __HAL_RCC_GPIOB_CLK_ENABLE(); // Uart tx, rx +// __HAL_RCC_USART1_CLK_ENABLE(); // Uart module } /* PWR, RCC, GPIO (All): AHB4 (D3 domain) @@ -198,6 +206,26 @@ void board_init(void) GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); +#if 0 + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UARTx; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&UartHandle); +#endif + #if BOARD_DEVICE_RHPORT_NUM == 0 // Despite being call USB2_OTG // OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port @@ -330,7 +358,8 @@ int board_uart_read(uint8_t* buf, int len) int board_uart_write(void const * buf, int len) { (void) buf; (void) len; - return 0; +// HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + return len; } diff --git a/hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h b/hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h index 2a9eb37ae..b9fa348ec 100644 --- a/hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h +++ b/hw/bsp/stm32h743eval/stm32h7xx_hal_conf.h @@ -100,7 +100,7 @@ /* #define HAL_SRAM_MODULE_ENABLED */ /* #define HAL_SWPMI_MODULE_ENABLED */ /* #define HAL_TIM_MODULE_ENABLED */ -/* #define HAL_UART_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED /* #define HAL_USART_MODULE_ENABLED */ /* #define HAL_WWDG_MODULE_ENABLED */ @@ -211,6 +211,8 @@ #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ #define USE_HAL_SWPMI_REGISTER_CALLBACKS 0U /* SWPMI register callback disabled */ #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ /* ########################### Ethernet Configuration ######################### */ -- cgit v1.3.1 From e0490ae7866e8553b261e298719f7805fcac6875 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 29 May 2020 13:06:33 +0700 Subject: fix idf usb pin init changes --- examples/device/cdc_msc_freertos/src/tusb_config.h | 6 ++++-- hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c | 9 +++++++++ 2 files changed, 13 insertions(+), 2 deletions(-) (limited to 'hw/bsp') diff --git a/examples/device/cdc_msc_freertos/src/tusb_config.h b/examples/device/cdc_msc_freertos/src/tusb_config.h index 794e996b6..40b7bced0 100644 --- a/examples/device/cdc_msc_freertos/src/tusb_config.h +++ b/examples/device/cdc_msc_freertos/src/tusb_config.h @@ -48,8 +48,10 @@ #define CFG_TUSB_OS OPT_OS_FREERTOS -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 +// can be defined by compiler in DEBUG build +#ifndef CFG_TUSB_DEBUG + #define CFG_TUSB_DEBUG 0 +#endif /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put diff --git a/hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c b/hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c index ef70f1ee2..bbcdab6d2 100644 --- a/hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c +++ b/hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c @@ -26,7 +26,9 @@ #include "../board.h" #include "driver/gpio.h" +#include "driver/periph_ctrl.h" #include "hal/usb_hal.h" +#include "soc/usb_periph.h" #include "driver/rmt.h" #include "led_strip/include/led_strip.h" @@ -66,10 +68,17 @@ void board_init(void) gpio_set_pull_mode(BUTTON_PIN, BUTTON_STATE_ACTIVE ? GPIO_PULLDOWN_ONLY : GPIO_PULLUP_ONLY); // USB Controller Hal init + periph_module_reset(PERIPH_USB_MODULE); + periph_module_enable(PERIPH_USB_MODULE); + usb_hal_context_t hal = { .use_external_phy = false // use built-in PHY }; usb_hal_init(&hal); + + // Pin drive strength + gpio_set_drive_capability(USBPHY_DM_NUM, GPIO_DRIVE_CAP_3); + gpio_set_drive_capability(USBPHY_DP_NUM, GPIO_DRIVE_CAP_3); } // Turn LED on or off -- cgit v1.3.1 From 5ffba8536dfaa4602e3e7f1c94be124bfeb3a5ae Mon Sep 17 00:00:00 2001 From: hathach Date: Sun, 31 May 2020 19:41:22 +0700 Subject: able to detect as hs --- hw/bsp/stm32h743eval/stm32h743eval.c | 13 +++++++++---- src/common/tusb_common.h | 4 +++- src/portable/st/synopsys/dcd_synopsys.c | 10 ++++++---- 3 files changed, 18 insertions(+), 9 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h743eval/stm32h743eval.c b/hw/bsp/stm32h743eval/stm32h743eval.c index d149c1230..836f1ecab 100644 --- a/hw/bsp/stm32h743eval/stm32h743eval.c +++ b/hw/bsp/stm32h743eval/stm32h743eval.c @@ -265,6 +265,7 @@ void board_init(void) #endif #if BOARD_DEVICE_RHPORT_NUM == 1 + // Despite being call USB2_OTG // OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port __GPIOA_CLK_ENABLE(); @@ -316,6 +317,8 @@ void board_init(void) GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; HAL_GPIO_Init(GPIOI, &GPIO_InitStruct); + + // Enable ULPI clock __HAL_RCC_USB1_OTG_HS_ULPI_CLK_ENABLE(); /* Enable USB HS Clocks */ @@ -325,12 +328,14 @@ void board_init(void) USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; // Force device mode - // USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; - // USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; + USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; + USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; // B-peripheral session valid override enabl -// USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; -// USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + + HAL_PWREx_EnableUSBVoltageDetector(); #endif // rhport = 1 } diff --git a/src/common/tusb_common.h b/src/common/tusb_common.h index f144cda73..d77893b6b 100644 --- a/src/common/tusb_common.h +++ b/src/common/tusb_common.h @@ -241,9 +241,9 @@ void tu_print_var(uint8_t const* buf, uint32_t bufsize) #define TU_LOG2 TU_LOG1 #define TU_LOG2_MEM TU_LOG1_MEM #define TU_LOG2_VAR TU_LOG1_VAR - #define TU_LOG2_LOCATION() TU_LOG1_LOCATION() #define TU_LOG2_INT TU_LOG1_INT #define TU_LOG2_HEX TU_LOG1_HEX + #define TU_LOG2_LOCATION() TU_LOG1_LOCATION() #endif @@ -277,6 +277,7 @@ static inline char const* lookup_find(lookup_table_t const* p_table, uint32_t ke #define TU_LOG1_VAR(...) #define TU_LOG1_INT(...) #define TU_LOG1_HEX(...) + #define TU_LOG1_LOCATION() #endif #ifndef TU_LOG2 @@ -285,6 +286,7 @@ static inline char const* lookup_find(lookup_table_t const* p_table, uint32_t ke #define TU_LOG2_VAR(...) #define TU_LOG2_INT(...) #define TU_LOG2_HEX(...) + #define TU_LOG2_LOCATION() #endif #ifdef __cplusplus diff --git a/src/portable/st/synopsys/dcd_synopsys.c b/src/portable/st/synopsys/dcd_synopsys.c index 8ca67dbb4..fe6fe5cea 100644 --- a/src/portable/st/synopsys/dcd_synopsys.c +++ b/src/portable/st/synopsys/dcd_synopsys.c @@ -197,6 +197,8 @@ static void end_of_reset(uint8_t rhport) // However, keep for debugging and in case Low Speed is ever supported. uint32_t enum_spd = (dev->DSTS & USB_OTG_DSTS_ENUMSPD_Msk) >> USB_OTG_DSTS_ENUMSPD_Pos; + // TODO set turnaround in GUSBCFG accordingly to the speed + // Maximum packet size for EP 0 is set for both directions by writing // DIEPCTL. if(enum_spd == 0x03) { @@ -239,7 +241,8 @@ void dcd_init (uint8_t rhport) // Turn around time for Highspeed is 0x09 usb_otg->GUSBCFG &= ~USB_OTG_GUSBCFG_TRDT; usb_otg->GUSBCFG |= (0x09 << USB_OTG_GUSBCFG_TRDT_Pos); - }else + } + else #endif { // Turn around programmed for 32+ MHz is 0x06 @@ -256,8 +259,6 @@ void dcd_init (uint8_t rhport) // Force device mode usb_otg->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; - TU_LOG2_LOCATION(); - // Restart PHY clock *((volatile uint32_t *)(_dcd_rhport[rhport].regs + USB_OTG_PCGCCTL_BASE)) = 0; @@ -282,8 +283,9 @@ void dcd_init (uint8_t rhport) dev->DCFG &= ~(3 << USB_OTG_DCFG_DSPD_Pos); // Transceiver delay, necessary for some ULPI PHYs - dev->DCFG |= (1 << 14); + //dev->DCFG |= (1 << 14); } + else #endif { // full speed with internal phy -- cgit v1.3.1 From e92118635cc8055a5ca599eaf9919d99a55bf584 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 1 Jun 2020 13:40:18 +0700 Subject: adding speed detect on bus reset --- hw/bsp/stm32h743eval/board.mk | 2 +- src/device/usbd.c | 7 +++++-- 2 files changed, 6 insertions(+), 3 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h743eval/board.mk b/hw/bsp/stm32h743eval/board.mk index 5c6c6ea4f..cbf37a95d 100644 --- a/hw/bsp/stm32h743eval/board.mk +++ b/hw/bsp/stm32h743eval/board.mk @@ -48,7 +48,7 @@ FREERTOS_PORT = ARM_CM7/r0p1 # For flash-jlink target JLINK_DEVICE = stm32h743xi -JLINK_IF = jtag +JLINK_IF = swd # flash target using on-board stlink flash: flash-stlink diff --git a/src/device/usbd.c b/src/device/usbd.c index 275792ab9..eeb5011ec 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -40,7 +40,8 @@ //--------------------------------------------------------------------+ // Device Data //--------------------------------------------------------------------+ -typedef struct { +typedef struct +{ struct TU_ATTR_PACKED { volatile uint8_t connected : 1; @@ -53,6 +54,8 @@ typedef struct { uint8_t self_powered : 1; // configuration descriptor's attribute }; + uint8_t speed; + uint8_t itf2drv[16]; // map interface number to driver (0xff is invalid) uint8_t ep2drv[8][2]; // map endpoint to driver ( 0xff is invalid ) @@ -384,7 +387,7 @@ void tud_task (void) { case DCD_EVENT_BUS_RESET: usbd_reset(event.rhport); - // TODO DCD should report operational speed (LS/FS/HS) + _usbd_dev.speed = event.bus_reset.speed; break; case DCD_EVENT_UNPLUGGED: -- cgit v1.3.1 From a347de6e50e98b339a1605dc927c0417e79b86a5 Mon Sep 17 00:00:00 2001 From: hathach Date: Sun, 14 Jun 2020 18:28:45 +0700 Subject: revert CFG_TUSB_RHPORT0_MODE to previous way --- examples/device/cdc_msc/src/tusb_config.h | 9 ++++++++- hw/bsp/stm32h743eval/stm32h743eval.c | 3 +-- src/tusb_option.h | 23 ++++++++++++----------- 3 files changed, 21 insertions(+), 14 deletions(-) (limited to 'hw/bsp') diff --git a/examples/device/cdc_msc/src/tusb_config.h b/examples/device/cdc_msc/src/tusb_config.h index 9beb9f6a2..b05d219c6 100644 --- a/examples/device/cdc_msc/src/tusb_config.h +++ b/examples/device/cdc_msc/src/tusb_config.h @@ -56,7 +56,14 @@ #endif // Device mode with rhport and speed defined by board.mk -#define CFG_TUSB_RHPORT0_MODE ((OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) << (8*BOARD_DEVICE_RHPORT_NUM)) +#if BOARD_DEVICE_RHPORT_NUM == 0 + #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) +#elif BOARD_DEVICE_RHPORT_NUM == 1 + #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) +#else + #error "Incorrect RHPort configuration" +#endif + #define CFG_TUSB_OS OPT_OS_NONE // CFG_TUSB_DEBUG is defined by compiler in DEBUG build diff --git a/hw/bsp/stm32h743eval/stm32h743eval.c b/hw/bsp/stm32h743eval/stm32h743eval.c index 836f1ecab..a28110920 100644 --- a/hw/bsp/stm32h743eval/stm32h743eval.c +++ b/hw/bsp/stm32h743eval/stm32h743eval.c @@ -262,9 +262,8 @@ void board_init(void) // Enable VBUS sense (B device) via pin PA9 USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; -#endif -#if BOARD_DEVICE_RHPORT_NUM == 1 +#elif BOARD_DEVICE_RHPORT_NUM == 1 // Despite being call USB2_OTG // OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port diff --git a/src/tusb_option.h b/src/tusb_option.h index c251d578a..01bb1301a 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -117,10 +117,7 @@ //-------------------------------------------------------------------- // RootHub Mode Configuration -// -// Each byte of the CFG_TUSB_RHPORTx_MODE contains operation mode for -// a roothub port (device or host). Therefore each macro can have up to -// 4 ports. +// CFG_TUSB_RHPORTx_MODE contains operation mode and speed for that port //-------------------------------------------------------------------- // Lower 4-bit is operational mode @@ -138,27 +135,31 @@ #define CFG_TUSB_RHPORT0_MODE OPT_MODE_NONE #endif -#if ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST ) && (CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)) ) || \ - ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) && (CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)) ) + +#ifndef CFG_TUSB_RHPORT1_MODE + #define CFG_TUSB_RHPORT1_MODE OPT_MODE_NONE +#endif + +#if ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST ) && (CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST )) || \ + ((CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) && (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE)) #error "TinyUSB currently does not support same modes on more than 1 roothub port" #endif // Which roothub port is configured as host -#define TUH_OPT_RHPORT ( (CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST) ? 0 : ((CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8)) ? 1 : -1) ) +#define TUH_OPT_RHPORT ( (CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST) ? 0 : ((CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST) ? 1 : -1) ) #define TUSB_OPT_HOST_ENABLED ( TUH_OPT_RHPORT >= 0 ) // Which roothub port is configured as device -#define TUD_OPT_RHPORT ( (CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) ? 0 : ((CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8)) ? 1 : -1) ) +#define TUD_OPT_RHPORT ( (CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) ? 0 : ((CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) ? 1 : -1) ) #if TUD_OPT_RHPORT == 0 - #define TUD_OPT_HIGH_SPEED ( CFG_TUSB_RHPORT0_MODE & OPT_MODE_HIGH_SPEED ) +#define TUD_OPT_HIGH_SPEED ( CFG_TUSB_RHPORT0_MODE & OPT_MODE_HIGH_SPEED ) #else - #define TUD_OPT_HIGH_SPEED ( CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HIGH_SPEED << 8) ) +#define TUD_OPT_HIGH_SPEED ( CFG_TUSB_RHPORT1_MODE & OPT_MODE_HIGH_SPEED ) #endif #define TUSB_OPT_DEVICE_ENABLED ( TUD_OPT_RHPORT >= 0 ) - //--------------------------------------------------------------------+ // COMMON OPTIONS //--------------------------------------------------------------------+ -- cgit v1.3.1 From 0bfa839ac0414632eb284779361ed6a34a98c672 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 15 Jun 2020 23:06:17 +0700 Subject: clean up, update other example config --- examples/device/cdc_dual_ports/src/tusb_config.h | 29 ++++++++++++++++---- examples/device/cdc_msc/src/tusb_config.h | 1 + examples/device/cdc_msc_freertos/src/tusb_config.h | 31 +++++++++++++++++----- hw/bsp/stm32h743eval/stm32h743eval.c | 10 +++---- 4 files changed, 55 insertions(+), 16 deletions(-) (limited to 'hw/bsp') diff --git a/examples/device/cdc_dual_ports/src/tusb_config.h b/examples/device/cdc_dual_ports/src/tusb_config.h index 3536702bb..e3368e72f 100644 --- a/examples/device/cdc_dual_ports/src/tusb_config.h +++ b/examples/device/cdc_dual_ports/src/tusb_config.h @@ -34,18 +34,37 @@ // COMMON CONFIGURATION //-------------------------------------------------------------------- -// defined by compiler flags for flexibility +// defined by board.mk #ifndef CFG_TUSB_MCU #error CFG_TUSB_MCU must be defined #endif -#if CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX || \ - CFG_TUSB_MCU == OPT_MCU_NUC505 || CFG_TUSB_MCU == OPT_MCU_CXD56 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | OPT_MODE_HIGH_SPEED) +// RHPort number used for device can be defined by board.mk, default to port 0 +#ifndef BOARD_DEVICE_RHPORT_NUM + #define BOARD_DEVICE_RHPORT_NUM 0 +#endif + +// RHPort max operational speed can defined by board.mk +// Default to Highspeed for MCU with internal HighSpeed PHY (can be port specific), otherwise FullSpeed +#ifndef BOARD_DEVICE_RHPORT_SPEED + #if (CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX || \ + CFG_TUSB_MCU == OPT_MCU_NUC505 || CFG_TUSB_MCU == OPT_MCU_CXD56) + #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_HIGH_SPEED + #else + #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_FULL_SPEED + #endif +#endif + +// Device mode with rhport and speed defined by board.mk +#if BOARD_DEVICE_RHPORT_NUM == 0 + #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) +#elif BOARD_DEVICE_RHPORT_NUM == 1 + #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) #else - #define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE + #error "Incorrect RHPort configuration" #endif +// This example doesn't use an RTOS #define CFG_TUSB_OS OPT_OS_NONE // CFG_TUSB_DEBUG is defined by compiler in DEBUG build diff --git a/examples/device/cdc_msc/src/tusb_config.h b/examples/device/cdc_msc/src/tusb_config.h index b05d219c6..c57c2ead8 100644 --- a/examples/device/cdc_msc/src/tusb_config.h +++ b/examples/device/cdc_msc/src/tusb_config.h @@ -64,6 +64,7 @@ #error "Incorrect RHPort configuration" #endif +// This example doesn't use an RTOS #define CFG_TUSB_OS OPT_OS_NONE // CFG_TUSB_DEBUG is defined by compiler in DEBUG build diff --git a/examples/device/cdc_msc_freertos/src/tusb_config.h b/examples/device/cdc_msc_freertos/src/tusb_config.h index 794e996b6..379fab971 100644 --- a/examples/device/cdc_msc_freertos/src/tusb_config.h +++ b/examples/device/cdc_msc_freertos/src/tusb_config.h @@ -34,19 +34,38 @@ // COMMON CONFIGURATION //-------------------------------------------------------------------- -// defined by compiler flags for flexibility +// defined by board.mk #ifndef CFG_TUSB_MCU #error CFG_TUSB_MCU must be defined #endif -#if CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX || \ - CFG_TUSB_MCU == OPT_MCU_NUC505 || CFG_TUSB_MCU == OPT_MCU_CXD56 - #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | OPT_MODE_HIGH_SPEED) +// RHPort number used for device can be defined by board.mk, default to port 0 +#ifndef BOARD_DEVICE_RHPORT_NUM + #define BOARD_DEVICE_RHPORT_NUM 0 +#endif + +// RHPort max operational speed can defined by board.mk +// Default to Highspeed for MCU with internal HighSpeed PHY (can be port specific), otherwise FullSpeed +#ifndef BOARD_DEVICE_RHPORT_SPEED + #if (CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX || \ + CFG_TUSB_MCU == OPT_MCU_NUC505 || CFG_TUSB_MCU == OPT_MCU_CXD56) + #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_HIGH_SPEED + #else + #define BOARD_DEVICE_RHPORT_SPEED OPT_MODE_FULL_SPEED + #endif +#endif + +// Device mode with rhport and speed defined by board.mk +#if BOARD_DEVICE_RHPORT_NUM == 0 + #define CFG_TUSB_RHPORT0_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) +#elif BOARD_DEVICE_RHPORT_NUM == 1 + #define CFG_TUSB_RHPORT1_MODE (OPT_MODE_DEVICE | BOARD_DEVICE_RHPORT_SPEED) #else - #define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE + #error "Incorrect RHPort configuration" #endif -#define CFG_TUSB_OS OPT_OS_FREERTOS +// This examples use FreeRTOS +#define CFG_TUSB_OS OPT_OS_FREERTOS // CFG_TUSB_DEBUG is defined by compiler in DEBUG build // #define CFG_TUSB_DEBUG 0 diff --git a/hw/bsp/stm32h743eval/stm32h743eval.c b/hw/bsp/stm32h743eval/stm32h743eval.c index a28110920..8bafc32cb 100644 --- a/hw/bsp/stm32h743eval/stm32h743eval.c +++ b/hw/bsp/stm32h743eval/stm32h743eval.c @@ -326,14 +326,14 @@ void board_init(void) // No VBUS sense USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + // B-peripheral session valid override enable + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + // Force device mode USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; - // B-peripheral session valid override enabl - USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; - USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; - HAL_PWREx_EnableUSBVoltageDetector(); #endif // rhport = 1 @@ -367,7 +367,7 @@ int board_uart_write(void const * buf, int len) } -#if CFG_TUSB_OS == OPT_OS_NONE +#if CFG_TUSB_OS == OPT_OS_NONE volatile uint32_t system_ticks = 0; void SysTick_Handler (void) { -- cgit v1.3.1 From 667eaa6dd693226d2595e2d19aa3f4798f0a4092 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 16 Jun 2020 00:03:52 +0700 Subject: fix stm32h743 priority with freeRTOS --- hw/bsp/stm32h743eval/stm32h743eval.c | 12 ++++++++---- src/portable/st/synopsys/dcd_synopsys.c | 9 +++++++-- 2 files changed, 15 insertions(+), 6 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h743eval/stm32h743eval.c b/hw/bsp/stm32h743eval/stm32h743eval.c index 8bafc32cb..772edf33c 100644 --- a/hw/bsp/stm32h743eval/stm32h743eval.c +++ b/hw/bsp/stm32h743eval/stm32h743eval.c @@ -185,10 +185,14 @@ void board_init(void) SystemClock_Config(); all_rcc_clk_enable(); - #if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); - #endif + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + +#if CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(OTG_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); + NVIC_SetPriority(OTG_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); +#endif GPIO_InitTypeDef GPIO_InitStruct; diff --git a/src/portable/st/synopsys/dcd_synopsys.c b/src/portable/st/synopsys/dcd_synopsys.c index 030c089aa..d636e581c 100644 --- a/src/portable/st/synopsys/dcd_synopsys.c +++ b/src/portable/st/synopsys/dcd_synopsys.c @@ -48,36 +48,41 @@ (CFG_TUSB_MCU == OPT_MCU_STM32L4 && defined(STM32L4_SYNOPSYS)) \ ) -// TODO Support OTG_HS // EP_MAX : Max number of bi-directional endpoints including EP0 // EP_FIFO_SIZE : Size of dedicated USB SRAM #if CFG_TUSB_MCU == OPT_MCU_STM32F1 #include "stm32f1xx.h" #define EP_MAX 4 #define EP_FIFO_SIZE 1280 + #elif CFG_TUSB_MCU == OPT_MCU_STM32F2 #include "stm32f2xx.h" #define EP_MAX USB_OTG_FS_MAX_IN_ENDPOINTS #define EP_FIFO_SIZE USB_OTG_FS_TOTAL_FIFO_SIZE + #elif CFG_TUSB_MCU == OPT_MCU_STM32F4 #include "stm32f4xx.h" #define EP_MAX USB_OTG_FS_MAX_IN_ENDPOINTS #define EP_FIFO_SIZE USB_OTG_FS_TOTAL_FIFO_SIZE + #elif CFG_TUSB_MCU == OPT_MCU_STM32H7 #include "stm32h7xx.h" #define EP_MAX 9 #define EP_FIFO_SIZE 4096 - // TODO The official name of the USB FS peripheral on H7 is "USB2_OTG_FS". + #elif CFG_TUSB_MCU == OPT_MCU_STM32F7 #include "stm32f7xx.h" #define EP_MAX 6 #define EP_FIFO_SIZE 1280 + #elif CFG_TUSB_MCU == OPT_MCU_STM32L4 #include "stm32l4xx.h" #define EP_MAX 6 #define EP_FIFO_SIZE 1280 + #else #error "Unsupported MCUs" + #endif #include "device/dcd.h" -- cgit v1.3.1 From 8e143fc962cb927dea6232d171aad85c7f4d44e4 Mon Sep 17 00:00:00 2001 From: Jerzy Kasenberg Date: Fri, 19 Jun 2020 14:02:09 +0200 Subject: Add board support for Dialog DA1469x-dk-pro This adds source files that allow to run TinyUSB stack on DA1469x-dk-pro board. Source files .c .S and .ld are taken from Apache Mynewt repository. Those files were stripped to allow starting board without Mynewt os. --- hw/bsp/board_mcu.h | 3 + hw/bsp/da1469x_dk_pro/board.mk | 64 +++ hw/bsp/da1469x_dk_pro/da1469x.ld | 245 +++++++++++ hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c | 127 ++++++ hw/bsp/da1469x_dk_pro/gcc_startup_da1469x.S | 301 ++++++++++++++ hw/bsp/da1469x_dk_pro/product_header.dump | Bin 0 -> 8192 bytes hw/bsp/da1469x_dk_pro/syscfg/syscfg.h | 34 ++ hw/mcu/dialog/da1469x/da1469x.ld | 228 +++++++++++ hw/mcu/dialog/da1469x/include/hal/hal_gpio.h | 184 +++++++++ hw/mcu/dialog/da1469x/include/mcu/da1469x_clock.h | 138 +++++++ hw/mcu/dialog/da1469x/include/mcu/da1469x_hal.h | 53 +++ hw/mcu/dialog/da1469x/include/mcu/mcu.h | 165 ++++++++ hw/mcu/dialog/da1469x/src/da1469x_clock.c | 159 +++++++ hw/mcu/dialog/da1469x/src/hal_gpio.c | 478 ++++++++++++++++++++++ hw/mcu/dialog/da1469x/src/hal_system.c | 136 ++++++ hw/mcu/dialog/da1469x/src/hal_system_start.c | 177 ++++++++ hw/mcu/dialog/da1469x/src/system_da1469x.c | 61 +++ 17 files changed, 2553 insertions(+) create mode 100644 hw/bsp/da1469x_dk_pro/board.mk create mode 100644 hw/bsp/da1469x_dk_pro/da1469x.ld create mode 100644 hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c create mode 100644 hw/bsp/da1469x_dk_pro/gcc_startup_da1469x.S create mode 100644 hw/bsp/da1469x_dk_pro/product_header.dump create mode 100644 hw/bsp/da1469x_dk_pro/syscfg/syscfg.h create mode 100644 hw/mcu/dialog/da1469x/da1469x.ld create mode 100644 hw/mcu/dialog/da1469x/include/hal/hal_gpio.h create mode 100644 hw/mcu/dialog/da1469x/include/mcu/da1469x_clock.h create mode 100644 hw/mcu/dialog/da1469x/include/mcu/da1469x_hal.h create mode 100644 hw/mcu/dialog/da1469x/include/mcu/mcu.h create mode 100644 hw/mcu/dialog/da1469x/src/da1469x_clock.c create mode 100644 hw/mcu/dialog/da1469x/src/hal_gpio.c create mode 100644 hw/mcu/dialog/da1469x/src/hal_system.c create mode 100644 hw/mcu/dialog/da1469x/src/hal_system_start.c create mode 100644 hw/mcu/dialog/da1469x/src/system_da1469x.c (limited to 'hw/bsp') diff --git a/hw/bsp/board_mcu.h b/hw/bsp/board_mcu.h index 825a67be3..15b31edfd 100644 --- a/hw/bsp/board_mcu.h +++ b/hw/bsp/board_mcu.h @@ -113,6 +113,9 @@ #elif CFG_TUSB_MCU == OPT_MCU_ESP32S2 // no header needed +#elif CFG_TUSB_MCU == OPT_MCU_DA1469X + #include "DA1469xAB.h" + #else #error "Missing MCU header" #endif diff --git a/hw/bsp/da1469x_dk_pro/board.mk b/hw/bsp/da1469x_dk_pro/board.mk new file mode 100644 index 000000000..c8a268aa5 --- /dev/null +++ b/hw/bsp/da1469x_dk_pro/board.mk @@ -0,0 +1,64 @@ + CFLAGS += \ + -flto \ + -mthumb \ + -mthumb-interwork \ + -mabi=aapcs \ + -mcpu=cortex-m33+nodsp \ + -mfloat-abi=hard \ + -mfpu=fpv5-sp-d16 \ + -nostdlib \ + -DCORE_M33 \ + -DCFG_TUSB_MCU=OPT_MCU_DA1469X \ + -DCFG_TUD_ENDPOINT0_SIZE=8\ + +# mcu driver cause following warnings +# CFLAGS += -Wno-error=strict-prototypes -Wno-error=unused-parameter + +MCU_FAMILY_DIR = hw/mcu/dialog/da1469x +MCU_DIR = hw/mcu/dialog/da14699 + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/da1469x.ld + +SRC_C += \ + $(MCU_FAMILY_DIR)/src/system_da1469x.c \ + $(MCU_FAMILY_DIR)/src/da1469x_clock.c \ + $(MCU_FAMILY_DIR)/src/hal_gpio.c \ + +SRC_S += $(TOP)/hw/bsp/$(BOARD)/gcc_startup_da1469x.S + +INC += \ + $(TOP)/hw/bsp/$(BOARD) \ + $(TOP)/$(MCU_DIR)/include \ + $(TOP)/$(MCU_FAMILY_DIR)/include \ + $(TOP)/$(MCU_FAMILY_DIR)/SDK_10.0.8.105/sdk/bsp/include \ + +# For TinyUSB port source +VENDOR = dialog +# While this is for da1469x chip, there is chance that da1468x chip family will also work +CHIP_FAMILY = da146xx + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM33_NTZ/non_secure + +# For flash-jlink target +JLINK_DEVICE = DA14699 +JLINK_IF = swd + +# flash using jlink but with some twists +flash: flash-dialog + +flash-dialog: $(BUILD)/$(BOARD)-firmware.bin + @echo '#define SW_VERSION "v_1.0.0.1"' >$(BUILD)/version.h + @echo '#define SW_VERSION_DATE "'`date +"%Y-%m-%d %H:%M"`'"' >>$(BUILD)/version.h + mkimage da1469x $(BUILD)/$(BOARD)-firmware.bin $(BUILD)/version.h $^.img + cp $(TOP)/hw/bsp/$(BOARD)/product_header.dump $(BUILD)/$(BOARD)-image.bin + cat $^.img >> $(BUILD)/$(BOARD)-image.bin + @echo r > $(BUILD)/$(BOARD).jlink + @echo halt >> $(BUILD)/$(BOARD).jlink + @echo loadfile $(BUILD)/$(BOARD)-image.bin 0x16000000 >> $(BUILD)/$(BOARD).jlink + @echo r >> $(BUILD)/$(BOARD).jlink + @echo go >> $(BUILD)/$(BOARD).jlink + @echo exit >> $(BUILD)/$(BOARD).jlink + $(JLINKEXE) -device $(JLINK_DEVICE) -if $(JLINK_IF) -JTAGConf -1,-1 -speed auto -CommandFile $(BUILD)/$(BOARD).jlink + diff --git a/hw/bsp/da1469x_dk_pro/da1469x.ld b/hw/bsp/da1469x_dk_pro/da1469x.ld new file mode 100644 index 000000000..96507d6e7 --- /dev/null +++ b/hw/bsp/da1469x_dk_pro/da1469x.ld @@ -0,0 +1,245 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +MEMORY +{ + /* + * Flash is remapped at 0x0 by 1st stage bootloader, but this is done with + * an offset derived from image header thus it is safer to use remapped + * address space at 0x0 instead of QSPI_M address space at 0x16000000. + * Bootloader partition is 32K, but 9K is currently reserved for product + * header (8K) and image header (1K). + * First 512 bytes of SYSRAM are remapped at 0x0 and used as ISR vector + * (there's no need to reallocate ISR vector) and thus cannot be used by + * application. + */ + + FLASH (r) : ORIGIN = (0x00000000), LENGTH = (1024 * 1024) + RAM (rw) : ORIGIN = (0x20000000), LENGTH = (512 * 1024) +} + +OUTPUT_FORMAT ("elf32-littlearm", "elf32-bigarm", "elf32-littlearm") + +/* Linker script to place sections and symbol values. Should be used together + * with other linker script that defines memory regions FLASH and RAM. + * It references following symbols, which must be defined in code: + * Reset_Handler : Entry of reset handler + * + * It defines following symbols, which code can use without definition: + * __exidx_start + * __exidx_end + * __etext + * __data_start__ + * __preinit_array_start + * __preinit_array_end + * __init_array_start + * __init_array_end + * __fini_array_start + * __fini_array_end + * __data_end__ + * __bss_start__ + * __bss_end__ + * __HeapBase + * __HeapLimit + * __StackLimit + * __StackTop + * __stack + * __bssnz_start__ + * __bssnz_end__ + */ +ENTRY(Reset_Handler) + +SECTIONS +{ + __text = .; + + .text : + { + __isr_vector_start = .; + KEEP(*(.isr_vector)) + /* ISR vector shall have exactly 512 bytes */ + . = __isr_vector_start + 0x200; + __isr_vector_end = .; + + *(.text) + *(.text.*) + + *(.libcmac.rom) + + KEEP(*(.init)) + KEEP(*(.fini)) + + /* .ctors */ + *crtbegin.o(.ctors) + *crtbegin?.o(.ctors) + *(EXCLUDE_FILE(*crtend?.o *crtend.o) .ctors) + *(SORT(.ctors.*)) + *(.ctors) + + /* .dtors */ + *crtbegin.o(.dtors) + *crtbegin?.o(.dtors) + *(EXCLUDE_FILE(*crtend?.o *crtend.o) .dtors) + *(SORT(.dtors.*)) + *(.dtors) + + *(.rodata*) + + *(.eh_frame*) + . = ALIGN(4); + } > FLASH + + .ARM.extab : + { + *(.ARM.extab* .gnu.linkonce.armextab.*) + . = ALIGN(4); + } > FLASH + + __exidx_start = .; + .ARM : + { + *(.ARM.exidx* .gnu.linkonce.armexidx.*) + . = ALIGN(4); + } > FLASH + __exidx_end = .; + + .intvect : + { + . = ALIGN(4); + __intvect_start__ = .; + . = . + (__isr_vector_end - __isr_vector_start); + . = ALIGN(4); + } > RAM + + .sleep_state (NOLOAD) : + { + . = ALIGN(4); + *(sleep_state) + } > RAM + + /* This section will be zeroed by RTT package init */ + .rtt (NOLOAD): + { + . = ALIGN(4); + *(.rtt) + . = ALIGN(4); + } > RAM + + __text_ram_addr = LOADADDR(.text_ram); + + .text_ram : + { + . = ALIGN(4); + __text_ram_start__ = .; + *(.text_ram*) + . = ALIGN(4); + __text_ram_end__ = .; + } > RAM AT > FLASH + + __etext = LOADADDR(.data); + + .data : + { + __data_start__ = .; + *(vtable) + *(.data*) + + . = ALIGN(4); + /* preinit data */ + PROVIDE_HIDDEN (__preinit_array_start = .); + *(.preinit_array) + PROVIDE_HIDDEN (__preinit_array_end = .); + + . = ALIGN(4); + /* init data */ + PROVIDE_HIDDEN (__init_array_start = .); + *(SORT(.init_array.*)) + *(.init_array) + PROVIDE_HIDDEN (__init_array_end = .); + + + . = ALIGN(4); + /* finit data */ + PROVIDE_HIDDEN (__fini_array_start = .); + *(SORT(.fini_array.*)) + *(.fini_array) + PROVIDE_HIDDEN (__fini_array_end = .); + + *(.jcr) + . = ALIGN(4); + /* All data end */ + __data_end__ = .; + } > RAM AT > FLASH + + .bssnz : + { + . = ALIGN(4); + __bssnz_start__ = .; + *(.bss.core.nz*) + . = ALIGN(4); + __bssnz_end__ = .; + } > RAM + + .bss : + { + . = ALIGN(4); + __bss_start__ = .; + *(.bss*) + *(COMMON) + . = ALIGN(4); + __bss_end__ = .; + } > RAM + + .cmac (NOLOAD) : + { + . = ALIGN(0x400); + *(.libcmac.ram) + } > RAM + + /* Heap starts after BSS */ + . = ALIGN(8); + __HeapBase = .; + + /* .stack_dummy section doesn't contains any symbols. It is only + * used for linker to calculate size of stack sections, and assign + * values to stack symbols later */ + .stack_dummy (COPY): + { + *(.stack*) + } > RAM + + _ram_start = ORIGIN(RAM); + + /* Set stack top to end of RAM, and stack limit move down by + * size of stack_dummy section */ + __StackTop = ORIGIN(RAM) + LENGTH(RAM); + __StackLimit = __StackTop - SIZEOF(.stack_dummy); + PROVIDE(__stack = __StackTop); + + /* Top of head is the bottom of the stack */ + __HeapLimit = __StackLimit; + end = __HeapLimit; + + /* Check if data + heap + stack exceeds RAM limit */ + ASSERT(__HeapBase <= __HeapLimit, "region RAM overflowed with stack") + + /* Check that intvect is at the beginning of RAM */ + ASSERT(__intvect_start__ == ORIGIN(RAM), "intvect is not at beginning of RAM") +} + diff --git a/hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c b/hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c new file mode 100644 index 000000000..85fa17152 --- /dev/null +++ b/hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c @@ -0,0 +1,127 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020 Jerzy Kasenberg + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board.h" +#include +#include + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB_IRQHandler(void) +{ + tud_int_handler(0); +} + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PIN 33 +#define LED_STATE_ON 1 +#define LED_STATE_OFF 0 + +#define BUTTON_PIN 6 + +void UnhandledIRQ(void) +{ + CRG_TOP->SYS_CTRL_REG = 0x80; + __BKPT(1); + while(1); +} + +void board_init(void) +{ + // LED + hal_gpio_init_out(LED_PIN, LED_STATE_ON); + + hal_gpio_init_out(1, 0); + hal_gpio_init_out(2, 0); + hal_gpio_init_out(3, 0); + hal_gpio_init_out(4, 0); + hal_gpio_init_out(5, 0); + + // Button + hal_gpio_init_in(BUTTON_PIN, HAL_GPIO_PULL_NONE); + + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + + NVIC_SetPriority(USB_IRQn, 2); + + /* Setup USB IRQ */ + NVIC_SetPriority(USB_IRQn, 2); + NVIC_EnableIRQ(USB_IRQn); + + /* Use PLL96 / 2 clock not HCLK */ + CRG_TOP->CLK_CTRL_REG &= ~CRG_TOP_CLK_CTRL_REG_USB_CLK_SRC_Msk; + + mcu_gpio_set_pin_function(14, MCU_GPIO_MODE_INPUT, MCU_GPIO_FUNC_USB); + mcu_gpio_set_pin_function(15, MCU_GPIO_MODE_INPUT, MCU_GPIO_FUNC_USB); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + hal_gpio_write(LED_PIN, state ? LED_STATE_ON : LED_STATE_OFF); +} + +uint32_t board_button_read(void) +{ + // button is active LOW + return hal_gpio_read(BUTTON_PIN) ^ 1; +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void)buf; + (void)len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + (void)buf; + (void)len; + + return 0; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif diff --git a/hw/bsp/da1469x_dk_pro/gcc_startup_da1469x.S b/hw/bsp/da1469x_dk_pro/gcc_startup_da1469x.S new file mode 100644 index 000000000..d47fbcd97 --- /dev/null +++ b/hw/bsp/da1469x_dk_pro/gcc_startup_da1469x.S @@ -0,0 +1,301 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + + #include "syscfg/syscfg.h" + + .syntax unified + .arch armv7-m + + .section .stack + .align 3 +#ifdef __STACK_SIZE + .equ Stack_Size, __STACK_SIZE +#else + .equ Stack_Size, 0xC00 +#endif + .equ SYS_CTRL_REG, 0x50000024 + .equ CACHE_FLASH_REG, 0x100C0040 + .equ RESET_STAT_REG, 0x500000BC + + .globl __StackTop + .globl __StackLimit +__StackLimit: + .space Stack_Size + .size __StackLimit, . - __StackLimit +__StackTop: + .size __StackTop, . - __StackTop + + .section .heap + .align 3 +#ifdef __HEAP_SIZE + .equ Heap_Size, __HEAP_SIZE +#else + .equ Heap_Size, 0 +#endif + .globl __HeapBase + .globl __HeapLimit +__HeapBase: + .if Heap_Size + .space Heap_Size + .endif + .size __HeapBase, . - __HeapBase +__HeapLimit: + .size __HeapLimit, . - __HeapLimit + + .section .isr_vector + .align 2 + .globl __isr_vector +__isr_vector: + .long __StackTop + .long Reset_Handler + /* Cortex-M33 interrupts */ + .long NMI_Handler + .long HardFault_Handler + .long MemoryManagement_Handler + .long BusFault_Handler + .long UsageFault_Handler + .long SecureFault_Handler + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long SVC_Handler + .long DebugMonitor_Handler + .long 0 /* Reserved */ + .long PendSV_Handler + .long SysTick_Handler + /* DA1469x interrupts */ + .long SENSOR_NODE_IRQHandler + .long DMA_IRQHandler + .long CHARGER_STATE_IRQHandler + .long CHARGER_ERROR_IRQHandler + .long CMAC2SYS_IRQHandler + .long UART_IRQHandler + .long UART2_IRQHandler + .long UART3_IRQHandler + .long I2C_IRQHandler + .long I2C2_IRQHandler + .long SPI_IRQHandler + .long SPI2_IRQHandler + .long PCM_IRQHandler + .long SRC_IN_IRQHandler + .long SRC_OUT_IRQHandler + .long USB_IRQHandler + .long TIMER_IRQHandler + .long TIMER2_IRQHandler + .long RTC_IRQHandler + .long KEY_WKUP_GPIO_IRQHandler + .long PDC_IRQHandler + .long VBUS_IRQHandler + .long MRM_IRQHandler + .long MOTOR_CONTROLLER_IRQHandler + .long TRNG_IRQHandler + .long DCDC_IRQHandler + .long XTAL32M_RDY_IRQHandler + .long ADC_IRQHandler + .long ADC2_IRQHandler + .long CRYPTO_IRQHandler + .long CAPTIMER1_IRQHandler + .long RFDIAG_IRQHandler + .long LCD_CONTROLLER_IRQHandler + .long PLL_LOCK_IRQHandler + .long TIMER3_IRQHandler + .long TIMER4_IRQHandler + .long LRA_IRQHandler + .long RTC_EVENT_IRQHandler + .long GPIO_P0_IRQHandler + .long GPIO_P1_IRQHandler + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .size __isr_vector, . - __isr_vector + + .text + .thumb + .thumb_func + .align 2 + .globl Reset_Handler + .type Reset_Handler, %function +Reset_Handler: + /* Make sure interrupt vector is remapped at 0x0 */ + ldr r1, =SYS_CTRL_REG + ldrh r2, [r1, #0] + orrs r2, r2, #8 + strh r2, [r1, #0] + +#if !MYNEWT_VAL(RAM_RESIDENT) +/* + * Flash is remapped at 0x0 with an offset, i.e. 0x0 does not correspond to + * 0x16000000 but to start of an image on flash. This is calculated from product + * header by 1st state bootloader and configured in CACHE_FLASH_REG. We need to + * retrieve proper offset value for calculations later. + */ + ldr r1, =CACHE_FLASH_REG + ldr r4, [r1, #0] + mov r2, r4 + mov r3, #0xFFFF + bic r4, r4, r3 /* CACHE_FLASH_REG[FLASH_REGION_BASE] */ + mov r3, #0xFFF0 + and r2, r2, r3 /* CACHE_FLASH_REG[FLASH_REGION_OFFSET] */ + lsr r2, r2, #2 + orr r4, r4, r2 + +/* Copy ISR vector from flash to RAM */ + ldr r1, =__isr_vector_start /* src ptr */ + ldr r2, =__isr_vector_end /* src end */ + ldr r3, =__intvect_start__ /* dst ptr */ +/* Make sure we copy from QSPIC address range, not from remapped range */ + cmp r1, r4 + itt lt + addlt r1, r1, r4 + addlt r2, r2, r4 +.loop_isr_copy: + cmp r1, r2 + ittt lt + ldrlt r0, [r1], #4 + strlt r0, [r3], #4 + blt .loop_isr_copy + +/* Copy QSPI code from flash to RAM */ + ldr r1, =__text_ram_addr /* src ptr */ + ldr r2, =__text_ram_start__ /* ptr */ + ldr r3, =__text_ram_end__ /* dst end */ +.loop_code_text_ram_copy: + cmp r2, r3 + ittt lt + ldrlt r0, [r1], #4 + strlt r0, [r2], #4 + blt .loop_code_text_ram_copy + +/* Copy data from flash to RAM */ + ldr r1, =__etext /* src ptr */ + ldr r2, =__data_start__ /* dst ptr */ + ldr r3, =__data_end__ /* dst end */ +.loop_data_copy: + cmp r2, r3 + ittt lt + ldrlt r0, [r1], #4 + strlt r0, [r2], #4 + blt .loop_data_copy +#endif + +/* Clear BSS */ + movs r0, 0 + ldr r1, =__bss_start__ + ldr r2, =__bss_end__ +.loop_bss_clear: + cmp r1, r2 + itt lt + strlt r0, [r1], #4 + blt .loop_bss_clear + + ldr r0, =__HeapBase + ldr r1, =__HeapLimit +/* Call static constructors */ + bl __libc_init_array + + bl SystemInit + bl main + + .pool + .size Reset_Handler, . - Reset_Handler + +/* Default interrupt handler */ + .type Default_Handler, %function +Default_Handler: + ldr r1, =SYS_CTRL_REG + ldrh r2, [r1, #0] + orrs r2, r2, #0x80 /* DEBUGGER_ENABLE */ + strh r2, [r1, #0] + b . + + .size Default_Handler, . - Default_Handler + +/* Default handlers for all interrupts */ + .macro IRQ handler + .weak \handler + .set \handler, Default_Handler + .endm + + /* Cortex-M33 interrupts */ + IRQ NMI_Handler + IRQ HardFault_Handler + IRQ MemoryManagement_Handler + IRQ BusFault_Handler + IRQ UsageFault_Handler + IRQ SecureFault_Handler + IRQ SVC_Handler + IRQ DebugMonitor_Handler + IRQ PendSV_Handler + IRQ SysTick_Handler + /* DA1469x interrupts */ + IRQ SENSOR_NODE_IRQHandler + IRQ DMA_IRQHandler + IRQ CHARGER_STATE_IRQHandler + IRQ CHARGER_ERROR_IRQHandler + IRQ CMAC2SYS_IRQHandler + IRQ UART_IRQHandler + IRQ UART2_IRQHandler + IRQ UART3_IRQHandler + IRQ I2C_IRQHandler + IRQ I2C2_IRQHandler + IRQ SPI_IRQHandler + IRQ SPI2_IRQHandler + IRQ PCM_IRQHandler + IRQ SRC_IN_IRQHandler + IRQ SRC_OUT_IRQHandler + IRQ USB_IRQHandler + IRQ TIMER_IRQHandler + IRQ TIMER2_IRQHandler + IRQ RTC_IRQHandler + IRQ KEY_WKUP_GPIO_IRQHandler + IRQ PDC_IRQHandler + IRQ VBUS_IRQHandler + IRQ MRM_IRQHandler + IRQ MOTOR_CONTROLLER_IRQHandler + IRQ TRNG_IRQHandler + IRQ DCDC_IRQHandler + IRQ XTAL32M_RDY_IRQHandler + IRQ ADC_IRQHandler + IRQ ADC2_IRQHandler + IRQ CRYPTO_IRQHandler + IRQ CAPTIMER1_IRQHandler + IRQ RFDIAG_IRQHandler + IRQ LCD_CONTROLLER_IRQHandler + IRQ PLL_LOCK_IRQHandler + IRQ TIMER3_IRQHandler + IRQ TIMER4_IRQHandler + IRQ LRA_IRQHandler + IRQ RTC_EVENT_IRQHandler + IRQ GPIO_P0_IRQHandler + IRQ GPIO_P1_IRQHandler + IRQ RESERVED40_IRQHandler + IRQ RESERVED41_IRQHandler + IRQ RESERVED42_IRQHandler + IRQ RESERVED43_IRQHandler + IRQ RESERVED44_IRQHandler + IRQ RESERVED45_IRQHandler + IRQ RESERVED46_IRQHandler + IRQ RESERVED47_IRQHandler + +.end diff --git a/hw/bsp/da1469x_dk_pro/product_header.dump b/hw/bsp/da1469x_dk_pro/product_header.dump new file mode 100644 index 000000000..ea4842242 Binary files /dev/null and b/hw/bsp/da1469x_dk_pro/product_header.dump differ diff --git a/hw/bsp/da1469x_dk_pro/syscfg/syscfg.h b/hw/bsp/da1469x_dk_pro/syscfg/syscfg.h new file mode 100644 index 000000000..6cbb4319e --- /dev/null +++ b/hw/bsp/da1469x_dk_pro/syscfg/syscfg.h @@ -0,0 +1,34 @@ +/** + * This file was generated by Apache newt version: 1.9.0-dev + */ + +#ifndef H_MYNEWT_SYSCFG_ +#define H_MYNEWT_SYSCFG_ + +/** + * This macro exists to ensure code includes this header when needed. If code + * checks the existence of a setting directly via ifdef without including this + * header, the setting macro will silently evaluate to 0. In contrast, an + * attempt to use these macros without including this header will result in a + * compiler error. + */ +#define MYNEWT_VAL(_name) MYNEWT_VAL_ ## _name +#define MYNEWT_VAL_CHOICE(_name, _val) MYNEWT_VAL_ ## _name ## __ ## _val + +#ifndef MYNEWT_VAL_RAM_RESIDENT +#define MYNEWT_VAL_RAM_RESIDENT (0) +#endif + +#ifndef MYNEWT_VAL_MCU_GPIO_MAX_IRQ +#define MYNEWT_VAL_MCU_GPIO_MAX_IRQ (4) +#endif + +#ifndef MYNEWT_VAL_MCU_GPIO_RETAINABLE_NUM +#define MYNEWT_VAL_MCU_GPIO_RETAINABLE_NUM (-1) +#endif + +#ifndef MYNEWT_VAL_MCU_CLOCK_XTAL32M_SETTLE_TIME_US +#define MYNEWT_VAL_MCU_CLOCK_XTAL32M_SETTLE_TIME_US (2000) +#endif + +#endif diff --git a/hw/mcu/dialog/da1469x/da1469x.ld b/hw/mcu/dialog/da1469x/da1469x.ld new file mode 100644 index 000000000..c91dea841 --- /dev/null +++ b/hw/mcu/dialog/da1469x/da1469x.ld @@ -0,0 +1,228 @@ +/* Linker script for Dialog DA1469x devices + * + * Version: Sourcery G++ 4.5-1 + * Support: https://support.codesourcery.com/GNUToolchain/ + * + * Copyright (c) 2007, 2008, 2009, 2010 CodeSourcery, Inc. + * + * The authors hereby grant permission to use, copy, modify, distribute, + * and license this software and its documentation for any purpose, provided + * that existing copyright notices are retained in all copies and that this + * notice is included verbatim in any distributions. No written agreement, + * license, or royalty fee is required for any of the authorized uses. + * Modifications to this software may be copyrighted by their authors + * and need not follow the licensing terms described here, provided that + * the new terms are clearly indicated on the first page of each file where + * they apply. + */ +OUTPUT_FORMAT ("elf32-littlearm", "elf32-bigarm", "elf32-littlearm") + +/* Linker script to place sections and symbol values. Should be used together + * with other linker script that defines memory regions FLASH and RAM. + * It references following symbols, which must be defined in code: + * Reset_Handler : Entry of reset handler + * + * It defines following symbols, which code can use without definition: + * __exidx_start + * __exidx_end + * __etext + * __data_start__ + * __preinit_array_start + * __preinit_array_end + * __init_array_start + * __init_array_end + * __fini_array_start + * __fini_array_end + * __data_end__ + * __bss_start__ + * __bss_end__ + * __HeapBase + * __HeapLimit + * __StackLimit + * __StackTop + * __stack + * __bssnz_start__ + * __bssnz_end__ + */ +ENTRY(Reset_Handler) + +SECTIONS +{ + .imghdr (NOLOAD): + { + . = . + _imghdr_size; + } > FLASH + + __text = .; + + .text : + { + __isr_vector_start = .; + KEEP(*(.isr_vector)) + /* ISR vector shall have exactly 512 bytes */ + . = __isr_vector_start + 0x200; + __isr_vector_end = .; + + *(.text) + *(.text.*) + + KEEP(*(.init)) + KEEP(*(.fini)) + + /* .ctors */ + *crtbegin.o(.ctors) + *crtbegin?.o(.ctors) + *(EXCLUDE_FILE(*crtend?.o *crtend.o) .ctors) + *(SORT(.ctors.*)) + *(.ctors) + + /* .dtors */ + *crtbegin.o(.dtors) + *crtbegin?.o(.dtors) + *(EXCLUDE_FILE(*crtend?.o *crtend.o) .dtors) + *(SORT(.dtors.*)) + *(.dtors) + + *(.rodata*) + + *(.eh_frame*) + . = ALIGN(4); + } > FLASH + + .ARM.extab : + { + *(.ARM.extab* .gnu.linkonce.armextab.*) + . = ALIGN(4); + } > FLASH + + __exidx_start = .; + .ARM.exidx : + { + *(.ARM.exidx* .gnu.linkonce.armexidx.*) + . = ALIGN(4); + } > FLASH + __exidx_end = .; + + .intvect : + { + . = ALIGN(4); + __intvect_start__ = .; + . = . + (__isr_vector_end - __isr_vector_start); + . = ALIGN(4); + } > RAM + + .sleep_state (NOLOAD) : + { + . = ALIGN(4); + *(sleep_state) + } > RAM + + /* This section will be zeroed by RTT package init */ + .rtt (NOLOAD): + { + . = ALIGN(4); + *(.rtt) + . = ALIGN(4); + } > RAM + + __text_ram_addr = LOADADDR(.text_ram); + + .text_ram : + { + . = ALIGN(4); + __text_ram_start__ = .; + *(.text_ram*) + . = ALIGN(4); + __text_ram_end__ = .; + } > RAM AT > FLASH + + __etext = LOADADDR(.data); + + .data : + { + __data_start__ = .; + *(vtable) + *(.data*) + + . = ALIGN(4); + /* preinit data */ + PROVIDE_HIDDEN (__preinit_array_start = .); + *(.preinit_array) + PROVIDE_HIDDEN (__preinit_array_end = .); + + . = ALIGN(4); + /* init data */ + PROVIDE_HIDDEN (__init_array_start = .); + *(SORT(.init_array.*)) + *(.init_array) + PROVIDE_HIDDEN (__init_array_end = .); + + + . = ALIGN(4); + /* finit data */ + PROVIDE_HIDDEN (__fini_array_start = .); + *(SORT(.fini_array.*)) + *(.fini_array) + PROVIDE_HIDDEN (__fini_array_end = .); + + *(.jcr) + . = ALIGN(4); + /* All data end */ + __data_end__ = .; + } > RAM AT > FLASH + + .bssnz : + { + . = ALIGN(4); + __bssnz_start__ = .; + *(.bss.core.nz*) + . = ALIGN(4); + __bssnz_end__ = .; + } > RAM + + .bss : + { + . = ALIGN(4); + __bss_start__ = .; + *(.bss*) + *(COMMON) + . = ALIGN(4); + __bss_end__ = .; + } > RAM + + .cmac (NOLOAD) : + { + . = ALIGN(0x400); + *(.libcmac.ram) + } > RAM + + /* Heap starts after BSS */ + . = ALIGN(8); + __HeapBase = .; + + /* .stack_dummy section doesn't contains any symbols. It is only + * used for linker to calculate size of stack sections, and assign + * values to stack symbols later */ + .stack_dummy (COPY): + { + *(.stack*) + } > RAM + + _ram_start = ORIGIN(RAM); + + /* Set stack top to end of RAM, and stack limit move down by + * size of stack_dummy section */ + __StackTop = ORIGIN(RAM) + LENGTH(RAM); + __StackLimit = __StackTop - SIZEOF(.stack_dummy); + PROVIDE(__stack = __StackTop); + + /* Top of head is the bottom of the stack */ + __HeapLimit = __StackLimit; + + /* Check if data + heap + stack exceeds RAM limit */ + ASSERT(__HeapBase <= __HeapLimit, "region RAM overflowed with stack") + + /* Check that intvect is at the beginning of RAM */ + ASSERT(__intvect_start__ == ORIGIN(RAM), "intvect is not at beginning of RAM") +} + diff --git a/hw/mcu/dialog/da1469x/include/hal/hal_gpio.h b/hw/mcu/dialog/da1469x/include/hal/hal_gpio.h new file mode 100644 index 000000000..67fc3c144 --- /dev/null +++ b/hw/mcu/dialog/da1469x/include/hal/hal_gpio.h @@ -0,0 +1,184 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + + +/** + * @addtogroup HAL + * @{ + * @defgroup HALGpio HAL GPIO + * @{ + */ + +#ifndef H_HAL_GPIO_ +#define H_HAL_GPIO_ + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * The "mode" of the gpio. The gpio is either an input, output, or it is + * "not connected" (the pin specified is not functioning as a gpio) + */ +enum hal_gpio_mode_e { + /** Not connected */ + HAL_GPIO_MODE_NC = -1, + /** Input */ + HAL_GPIO_MODE_IN = 0, + /** Output */ + HAL_GPIO_MODE_OUT = 1 +}; +typedef enum hal_gpio_mode_e hal_gpio_mode_t; + +/* + * The "pull" of the gpio. This is either an input or an output. + */ +enum hal_gpio_pull { + /** Pull-up/down not enabled */ + HAL_GPIO_PULL_NONE = 0, + /** Pull-up enabled */ + HAL_GPIO_PULL_UP = 1, + /** Pull-down enabled */ + HAL_GPIO_PULL_DOWN = 2 +}; +typedef enum hal_gpio_pull hal_gpio_pull_t; + +/* + * IRQ trigger type. + */ +enum hal_gpio_irq_trigger { + HAL_GPIO_TRIG_NONE = 0, + /** IRQ occurs on rising edge */ + HAL_GPIO_TRIG_RISING = 1, + /** IRQ occurs on falling edge */ + HAL_GPIO_TRIG_FALLING = 2, + /** IRQ occurs on either edge */ + HAL_GPIO_TRIG_BOTH = 3, + /** IRQ occurs when line is low */ + HAL_GPIO_TRIG_LOW = 4, + /** IRQ occurs when line is high */ + HAL_GPIO_TRIG_HIGH = 5 +}; +typedef enum hal_gpio_irq_trigger hal_gpio_irq_trig_t; + +/* Function proto for GPIO irq handler functions */ +typedef void (*hal_gpio_irq_handler_t)(void *arg); + +/** + * Initializes the specified pin as an input + * + * @param pin Pin number to set as input + * @param pull pull type + * + * @return int 0: no error; -1 otherwise. + */ +int hal_gpio_init_in(int pin, hal_gpio_pull_t pull); + +/** + * Initialize the specified pin as an output, setting the pin to the specified + * value. + * + * @param pin Pin number to set as output + * @param val Value to set pin + * + * @return int 0: no error; -1 otherwise. + */ +int hal_gpio_init_out(int pin, int val); + +/** + * Deinitialize the specified pin to revert the previous initialization + * + * @param pin Pin number to unset + * + * @return int 0: no error; -1 otherwise. + */ +int hal_gpio_deinit(int pin); + +/** + * Write a value (either high or low) to the specified pin. + * + * @param pin Pin to set + * @param val Value to set pin (0:low 1:high) + */ +void hal_gpio_write(int pin, int val); + +/** + * Reads the specified pin. + * + * @param pin Pin number to read + * + * @return int 0: low, 1: high + */ +int hal_gpio_read(int pin); + +/** + * Toggles the specified pin + * + * @param pin Pin number to toggle + * + * @return current gpio state int 0: low, 1: high + */ +int hal_gpio_toggle(int pin); + +/** + * Initialize a given pin to trigger a GPIO IRQ callback. + * + * @param pin The pin to trigger GPIO interrupt on + * @param handler The handler function to call + * @param arg The argument to provide to the IRQ handler + * @param trig The trigger mode (e.g. rising, falling) + * @param pull The mode of the pin (e.g. pullup, pulldown) + * + * @return 0 on success, non-zero error code on failure. + */ +int hal_gpio_irq_init(int pin, hal_gpio_irq_handler_t handler, void *arg, + hal_gpio_irq_trig_t trig, hal_gpio_pull_t pull); + +/** + * Release a pin from being configured to trigger IRQ on state change. + * + * @param pin The pin to release + */ +void hal_gpio_irq_release(int pin); + +/** + * Enable IRQs on the passed pin + * + * @param pin The pin to enable IRQs on + */ +void hal_gpio_irq_enable(int pin); + +/** + * Disable IRQs on the passed pin + * + * @param pin The pin to disable IRQs on + */ +void hal_gpio_irq_disable(int pin); + + +#ifdef __cplusplus +} +#endif + +#endif /* H_HAL_GPIO_ */ + +/** + * @} HALGpio + * @} HAL + */ diff --git a/hw/mcu/dialog/da1469x/include/mcu/da1469x_clock.h b/hw/mcu/dialog/da1469x/include/mcu/da1469x_clock.h new file mode 100644 index 000000000..3c697747d --- /dev/null +++ b/hw/mcu/dialog/da1469x/include/mcu/da1469x_clock.h @@ -0,0 +1,138 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +#ifndef __MCU_DA1469X_CLOCK_H_ +#define __MCU_DA1469X_CLOCK_H_ + +#include +#include "mcu/da1469x_hal.h" + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * Initialize XTAL32M + */ +void da1469x_clock_sys_xtal32m_init(void); + +/** + * Enable XTAL32M + */ +void da1469x_clock_sys_xtal32m_enable(void); + +/** + * Wait for XTAL32M to settle + */ +void da1469x_clock_sys_xtal32m_wait_to_settle(void); + +/** + * Switch sys_clk to XTAL32M + * + * Caller shall ensure that XTAL32M is already settled. + */ +void da1469x_clock_sys_xtal32m_switch(void); + +/** + * Switch sys_clk to XTAL32M + * + * Waits for XTAL32M to settle before switching. + */ +void da1469x_clock_sys_xtal32m_switch_safe(void); + +/** + * Disable RC32M + */ +void da1469x_clock_sys_rc32m_disable(void); + +/** + * Enable AMBA clock(s) + * + * @param mask + */ +static inline void +da1469x_clock_amba_enable(uint32_t mask) +{ + uint32_t primask; + + __HAL_DISABLE_INTERRUPTS(primask); + CRG_TOP->CLK_AMBA_REG |= mask; + __HAL_ENABLE_INTERRUPTS(primask); +} + +/** + * Disable AMBA clock(s) + * + * @param uint32_t mask + */ +static inline void +da1469x_clock_amba_disable(uint32_t mask) +{ + uint32_t primask; + + __HAL_DISABLE_INTERRUPTS(primask); + CRG_TOP->CLK_AMBA_REG &= ~mask; + __HAL_ENABLE_INTERRUPTS(primask); +} + +/** + * Enable PLL96 + */ +static inline void +da1469x_clock_sys_pll_enable(void) +{ + CRG_XTAL->PLL_SYS_CTRL1_REG |= CRG_XTAL_PLL_SYS_CTRL1_REG_PLL_EN_Msk | + CRG_XTAL_PLL_SYS_CTRL1_REG_LDO_PLL_ENABLE_Msk; +} + +/** + * Disable PLL96 + * + * If PLL was used as SYS_CLOCK switches to XTAL32M. + */ +void da1469x_clock_sys_pll_disable(void); + +/** + * Checks whether PLL96 is locked and can be use as system clock or USB clock + * + * @return 0 if PLL is off, non-0 it its running + */ +static inline int +da1469x_clock_is_pll_locked(void) +{ + return 0 != (CRG_XTAL->PLL_SYS_STATUS_REG & CRG_XTAL_PLL_SYS_STATUS_REG_PLL_LOCK_FINE_Msk); +} + +/** + * Waits for PLL96 to lock. + */ +void da1469x_clock_pll_wait_to_lock(void); + +/** + * Switches system clock to PLL96 + * + * Caller shall ensure that PLL is already locked. + */ +void da1469x_clock_sys_pll_switch(void); + +#ifdef __cplusplus +} +#endif + +#endif /* __MCU_DA1469X_CLOCK_H_ */ diff --git a/hw/mcu/dialog/da1469x/include/mcu/da1469x_hal.h b/hw/mcu/dialog/da1469x/include/mcu/da1469x_hal.h new file mode 100644 index 000000000..28fa1aa88 --- /dev/null +++ b/hw/mcu/dialog/da1469x/include/mcu/da1469x_hal.h @@ -0,0 +1,53 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +#ifndef __MCU_DA1469X_HAL_H_ +#define __MCU_DA1469X_HAL_H_ + +#include +#include "mcu/mcu.h" + +#ifdef __cplusplus +extern "C" { +#endif + +/* Helper functions to enable/disable interrupts. */ +#define __HAL_DISABLE_INTERRUPTS(x) \ + do { \ + x = __get_PRIMASK(); \ + __disable_irq(); \ + } while (0) + +#define __HAL_ENABLE_INTERRUPTS(x) \ + do { \ + if (!x) { \ + __enable_irq(); \ + } \ + } while (0) + +#define __HAL_ASSERT_CRITICAL() \ + do { \ + assert(__get_PRIMASK() & 1); \ + } while (0) + +#ifdef __cplusplus +} +#endif + +#endif /* __MCU_DA1469X_HAL_H_ */ diff --git a/hw/mcu/dialog/da1469x/include/mcu/mcu.h b/hw/mcu/dialog/da1469x/include/mcu/mcu.h new file mode 100644 index 000000000..1e6736785 --- /dev/null +++ b/hw/mcu/dialog/da1469x/include/mcu/mcu.h @@ -0,0 +1,165 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +#ifndef __MCU_MCU_H_ +#define __MCU_MCU_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +#include "DA1469xAB.h" + +#define sec_text_ram_core __attribute__((section(".text_ram"))) __attribute__((noinline)) + +#define MCU_SYSVIEW_INTERRUPTS \ + "I#1=Reset,I#2=MNI,I#3=HardFault,I#4=MemoryMgmt,I#5=BusFault,I#6=UsageFault," \ + "I#7=SecureFault,I#11=SVCall,I#12=DebugMonitor,I#14=PendSV,I#15=SysTick," \ + "I#16=SENSOR_NODE,I#17=DMA,I#18=CHARGER_STATE,I#19=CHARGER_ERROR," \ + "I#20=CMAC2SYS,I#21=UART,I#22=UART2,I#23=UART3,I#24=I2C,I#25=I2C2,I#26=SPI," \ + "I#27=SPI2,I#28=PCM,I#29=SRC_IN,I#30=SRC_OUT,I#31=USB,I#32=TIMER," \ + "I#33=TIMER2,I#34=RTC,I#35=KEY_WKUP_GPIO,I#36=PDC,I#37=VBUS,I#38=MRM," \ + "I#39=MOTOR_CONTROLLER,I#40=TRNG,I#41=DCDC,I#42=XTAL32M_RDY,I#43=ADC," \ + "I#44=ADC2,I#45=CRYPTO,I#46=CAPTIMER1,I#47=RFDIAG,I#48=LCD_CONTROLLER," \ + "I#49=PLL_LOCK,I#50=TIMER3,I#51=TIMER4,I#52=LRA,I#53=RTC_EVENT," \ + "I#54=GPIO_P0,I#55=GPIO_P1" + +/** +* \brief GPIO function +* +*/ +typedef enum { + MCU_GPIO_FUNC_GPIO = 0, /**< GPIO */ + MCU_GPIO_FUNC_UART_RX = 1, /**< GPIO as UART RX */ + MCU_GPIO_FUNC_UART_TX = 2, /**< GPIO as UART TX */ + MCU_GPIO_FUNC_UART2_RX = 3, /**< GPIO as UART2 RX */ + MCU_GPIO_FUNC_UART2_TX = 4, /**< GPIO as UART2 TX */ + MCU_GPIO_FUNC_UART2_CTSN = 5, /**< GPIO as UART2 CTSN */ + MCU_GPIO_FUNC_UART2_RTSN = 6, /**< GPIO as UART2 RTSN */ + MCU_GPIO_FUNC_UART3_RX = 7, /**< GPIO as UART3 RX */ + MCU_GPIO_FUNC_UART3_TX = 8, /**< GPIO as UART3 TX */ + MCU_GPIO_FUNC_UART3_CTSN = 9, /**< GPIO as UART3 CTSN */ + MCU_GPIO_FUNC_UART3_RTSN = 10, /**< GPIO as UART3 RTSN */ + MCU_GPIO_FUNC_ISO_CLK = 11, /**< GPIO as ISO CLK */ + MCU_GPIO_FUNC_ISO_DATA = 12, /**< GPIO as ISO DATA */ + MCU_GPIO_FUNC_SPI_DI = 13, /**< GPIO as SPI DI */ + MCU_GPIO_FUNC_SPI_DO = 14, /**< GPIO as SPI DO */ + MCU_GPIO_FUNC_SPI_CLK = 15, /**< GPIO as SPI CLK */ + MCU_GPIO_FUNC_SPI_EN = 16, /**< GPIO as SPI EN */ + MCU_GPIO_FUNC_SPI2_DI = 17, /**< GPIO as SPI2 DI */ + MCU_GPIO_FUNC_SPI2_DO = 18, /**< GPIO as SPI2 DO */ + MCU_GPIO_FUNC_SPI2_CLK = 19, /**< GPIO as SPI2 CLK */ + MCU_GPIO_FUNC_SPI2_EN = 20, /**< GPIO as SPI2 EN */ + MCU_GPIO_FUNC_I2C_SCL = 21, /**< GPIO as I2C SCL */ + MCU_GPIO_FUNC_I2C_SDA = 22, /**< GPIO as I2C SDA */ + MCU_GPIO_FUNC_I2C2_SCL = 23, /**< GPIO as I2C2 SCL */ + MCU_GPIO_FUNC_I2C2_SDA = 24, /**< GPIO as I2C2 SDA */ + MCU_GPIO_FUNC_USB_SOF = 25, /**< GPIO as USB SOF */ + MCU_GPIO_FUNC_ADC = 26, /**< GPIO as ADC (dedicated pin) */ + MCU_GPIO_FUNC_USB = 27, /**< GPIO as USB */ + MCU_GPIO_FUNC_PCM_DI = 28, /**< GPIO as PCM DI */ + MCU_GPIO_FUNC_PCM_DO = 29, /**< GPIO as PCM DO */ + MCU_GPIO_FUNC_PCM_FSC = 30, /**< GPIO as PCM FSC */ + MCU_GPIO_FUNC_PCM_CLK = 31, /**< GPIO as PCM CLK */ + MCU_GPIO_FUNC_PDM_DATA = 32, /**< GPIO as PDM DATA */ + MCU_GPIO_FUNC_PDM_CLK = 33, /**< GPIO as PDM CLK */ + MCU_GPIO_FUNC_COEX_EXT_ACT = 34, /**< GPIO as COEX EXT ACT0 */ + MCU_GPIO_FUNC_COEX_SMART_ACT = 35, /**< GPIO as COEX SMART ACT */ + MCU_GPIO_FUNC_COEX_SMART_PRI = 36, /**< GPIO as COEX SMART PRI */ + MCU_GPIO_FUNC_PORT0_DCF = 37, /**< GPIO as PORT0 DCF */ + MCU_GPIO_FUNC_PORT1_DCF = 38, /**< GPIO as PORT1 DCF */ + MCU_GPIO_FUNC_PORT2_DCF = 39, /**< GPIO as PORT2 DCF */ + MCU_GPIO_FUNC_PORT3_DCF = 40, /**< GPIO as PORT3 DCF */ + MCU_GPIO_FUNC_PORT4_DCF = 41, /**< GPIO as PORT4 DCF */ + MCU_GPIO_FUNC_CLOCK = 42, /**< GPIO as CLOCK */ + MCU_GPIO_FUNC_PG = 43, /**< GPIO as PG */ + MCU_GPIO_FUNC_LCD = 44, /**< GPIO as LCD */ + MCU_GPIO_FUNC_LCD_SPI_DC = 45, /**< GPIO as LCD SPI DC */ + MCU_GPIO_FUNC_LCD_SPI_DO = 46, /**< GPIO as LCD SPI DO */ + MCU_GPIO_FUNC_LCD_SPI_CLK = 47, /**< GPIO as LCD SPI CLK */ + MCU_GPIO_FUNC_LCD_SPI_EN = 48, /**< GPIO as LCD SPI EN */ + MCU_GPIO_FUNC_TIM_PWM = 49, /**< GPIO as TIM PWM */ + MCU_GPIO_FUNC_TIM2_PWM = 50, /**< GPIO as TIM2 PWM */ + MCU_GPIO_FUNC_TIM_1SHOT = 51, /**< GPIO as TIM 1SHOT */ + MCU_GPIO_FUNC_TIM2_1SHOT = 52, /**< GPIO as TIM2 1SHOT */ + MCU_GPIO_FUNC_TIM3_PWM = 53, /**< GPIO as TIM3 PWM */ + MCU_GPIO_FUNC_TIM4_PWM = 54, /**< GPIO as TIM4 PWM */ + MCU_GPIO_FUNC_AGC_EXT = 55, /**< GPIO as AGC EXT */ + MCU_GPIO_FUNC_CMAC_DIAG0 = 56, /**< GPIO as CMAC DIAG0 */ + MCU_GPIO_FUNC_CMAC_DIAG1 = 57, /**< GPIO as CMAC DIAG1 */ + MCU_GPIO_FUNC_CMAC_DIAG2 = 58, /**< GPIO as CMAC DIAG2 */ + MCU_GPIO_FUNC_CMAC_DIAGX = 59, /**< GPIO as CMAC DIAGX */ + MCU_GPIO_FUNC_LAST, +} mcu_gpio_func; + +#define MCU_GPIO_MODE_INPUT 0x000 /**< GPIO as an input */ +#define MCU_GPIO_MODE_INPUT_PULLUP 0x100 /**< GPIO as an input with pull-up */ +#define MCU_GPIO_MODE_INPUT_PULLDOWN 0x200 /**< GPIO as an input with pull-down */ +#define MCU_GPIO_MODE_OUTPUT 0x300 /**< GPIO as an output */ +#define MCU_GPIO_MODE_OUTPUT_OPEN_DRAIN 0x700 /**< GPIO as an open-drain output */ + +#define MCU_GPIO_PORT0_PIN_COUNT 32 +#define MCU_GPIO_PORT0(pin) ((0 * 32) + (pin)) +#define MCU_GPIO_PORT1(pin) ((1 * 32) + (pin)) +#define MCU_DMA_CHAN_MAX 8 + +#define MCU_PIN_GPADC_SEL0 MCU_GPIO_PORT1(9) +#define MCU_PIN_GPADC_SEL1 MCU_GPIO_PORT0(25) +#define MCU_PIN_GPADC_SEL2 MCU_GPIO_PORT0(8) +#define MCU_PIN_GPADC_SEL3 MCU_GPIO_PORT0(9) +#define MCU_PIN_GPADC_SEL16 MCU_GPIO_PORT1(13) +#define MCU_PIN_GPADC_SEL17 MCU_GPIO_PORT1(12) +#define MCU_PIN_GPADC_SEL18 MCU_GPIO_PORT1(18) +#define MCU_PIN_GPADC_SEL19 MCU_GPIO_PORT1(19) +#define MCU_PIN_GPADC_DIFF0_P0 MCU_GPIO_PORT1(9) +#define MCU_PIN_GPADC_DIFF0_P1 MCU_GPIO_PORT0(25) +#define MCU_PIN_GPADC_DIFF1_P0 MCU_GPIO_PORT0(8) +#define MCU_PIN_GPADC_DIFF1_P1 MCU_GPIO_PORT0(9) + +#define MCU_PIN_SDADC0 MCU_GPIO_PORT1(9) +#define MCU_PIN_SDADC1 MCU_GPIO_PORT0(25) +#define MCU_PIN_SDADC2 MCU_GPIO_PORT0(8) +#define MCU_PIN_SDADC3 MCU_GPIO_PORT0(9) +#define MCU_PIN_SDADC4 MCU_GPIO_PORT1(14) +#define MCU_PIN_SDADC5 MCU_GPIO_PORT1(20) +#define MCU_PIN_SDADC6 MCU_GPIO_PORT1(21) +#define MCU_PIN_SDADC7 MCU_GPIO_PORT1(22) + +void mcu_gpio_set_pin_function(int pin, int mode, mcu_gpio_func func); +void mcu_gpio_enter_sleep(void); +void mcu_gpio_exit_sleep(void); + +#define MCU_MEM_QSPIF_M_END_REMAP_ADDRESS (0x800000) +#define MCU_MEM_QSPIF_M_START_ADDRESS (0x16000000) +#define MCU_MEM_QSPIF_M_END_ADDRESS (0x18000000) +#define MCU_MEM_SYSRAM_START_ADDRESS (0x20000000) +#define MCU_MEM_SYSRAM_END_ADDRESS (0x20080000) + +#define MCU_OTPM_BASE 0x30080000UL +#define MCU_OTPM_SIZE 4096 + +/* Largest group id seen on a DA14699 was 18 so far */ +#define MCU_TRIMV_GROUP_ID_MAX (18) + +#ifdef __cplusplus +} +#endif + +#endif /* __MCU_MCU_H_ */ + diff --git a/hw/mcu/dialog/da1469x/src/da1469x_clock.c b/hw/mcu/dialog/da1469x/src/da1469x_clock.c new file mode 100644 index 000000000..6b4f0e6cf --- /dev/null +++ b/hw/mcu/dialog/da1469x/src/da1469x_clock.c @@ -0,0 +1,159 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +#include +#include +#include +#include "syscfg/syscfg.h" +#include "mcu/da1469x_hal.h" +#include "mcu/da1469x_clock.h" + +static inline bool +da1469x_clock_is_xtal32m_settled(void) +{ + return ((*(uint32_t *)0x5001001c & 0xff00) == 0) && + ((*(uint32_t *)0x50010054 & 0x000f) != 0xb); +} + +void +da1469x_clock_sys_xtal32m_init(void) +{ + uint32_t reg; + int xtalrdy_cnt; + + /* Number of lp_clk cycles (~30.5us) */ + xtalrdy_cnt = MYNEWT_VAL(MCU_CLOCK_XTAL32M_SETTLE_TIME_US) * 10 / 305; + + reg = CRG_XTAL->XTALRDY_CTRL_REG; + reg &= ~(CRG_XTAL_XTALRDY_CTRL_REG_XTALRDY_CLK_SEL_Msk | + CRG_XTAL_XTALRDY_CTRL_REG_XTALRDY_CNT_Msk); + reg |= xtalrdy_cnt; + CRG_XTAL->XTALRDY_CTRL_REG = reg; +} + +void +da1469x_clock_sys_xtal32m_enable(void) +{ + PDC->PDC_CTRL0_REG = (2 << PDC_PDC_CTRL0_REG_TRIG_SELECT_Pos) | + (15 << PDC_PDC_CTRL0_REG_TRIG_ID_Pos) | + (1 << PDC_PDC_CTRL0_REG_PDC_MASTER_Pos) | + (1 << PDC_PDC_CTRL0_REG_EN_XTAL_Pos); + + PDC->PDC_SET_PENDING_REG = 0; + PDC->PDC_ACKNOWLEDGE_REG = 0; +} + +void +da1469x_clock_sys_xtal32m_switch(void) +{ + if (CRG_TOP->CLK_CTRL_REG & CRG_TOP_CLK_CTRL_REG_RUNNING_AT_RC32M_Msk) { + CRG_TOP->CLK_SWITCH2XTAL_REG = CRG_TOP_CLK_SWITCH2XTAL_REG_SWITCH2XTAL_Msk; + } else { + CRG_TOP->CLK_CTRL_REG &= ~CRG_TOP_CLK_CTRL_REG_SYS_CLK_SEL_Msk; + } + + while (!(CRG_TOP->CLK_CTRL_REG & CRG_TOP_CLK_CTRL_REG_RUNNING_AT_XTAL32M_Msk)); +} + +void +da1469x_clock_sys_xtal32m_wait_to_settle(void) +{ + uint32_t primask; + + __HAL_DISABLE_INTERRUPTS(primask); + + NVIC_ClearPendingIRQ(XTAL32M_RDY_IRQn); + + if (!da1469x_clock_is_xtal32m_settled()) { + NVIC_EnableIRQ(XTAL32M_RDY_IRQn); + while (!NVIC_GetPendingIRQ(XTAL32M_RDY_IRQn)) { + __WFI(); + } + NVIC_DisableIRQ(XTAL32M_RDY_IRQn); + } + + __HAL_ENABLE_INTERRUPTS(primask); +} + +void +da1469x_clock_sys_xtal32m_switch_safe(void) +{ + da1469x_clock_sys_xtal32m_wait_to_settle(); + + da1469x_clock_sys_xtal32m_switch(); +} + +void +da1469x_clock_sys_rc32m_disable(void) +{ + CRG_TOP->CLK_RC32M_REG &= ~CRG_TOP_CLK_RC32M_REG_RC32M_ENABLE_Msk; +} + +void +da1469x_clock_lp_xtal32k_enable(void) +{ + CRG_TOP->CLK_XTAL32K_REG |= CRG_TOP_CLK_XTAL32K_REG_XTAL32K_ENABLE_Msk; +} + +void +da1469x_clock_lp_xtal32k_switch(void) +{ + CRG_TOP->CLK_CTRL_REG = (CRG_TOP->CLK_CTRL_REG & + ~CRG_TOP_CLK_CTRL_REG_LP_CLK_SEL_Msk) | + (2 << CRG_TOP_CLK_CTRL_REG_LP_CLK_SEL_Pos); +} + +void +da1469x_clock_pll_disable(void) +{ + while (CRG_TOP->CLK_CTRL_REG & CRG_TOP_CLK_CTRL_REG_RUNNING_AT_PLL96M_Msk) { + CRG_TOP->CLK_SWITCH2XTAL_REG = CRG_TOP_CLK_SWITCH2XTAL_REG_SWITCH2XTAL_Msk; + } + + CRG_XTAL->PLL_SYS_CTRL1_REG &= ~CRG_XTAL_PLL_SYS_CTRL1_REG_PLL_EN_Msk; +} + +void +da1469x_clock_pll_wait_to_lock(void) +{ + uint32_t primask; + + __HAL_DISABLE_INTERRUPTS(primask); + + NVIC_ClearPendingIRQ(PLL_LOCK_IRQn); + + if (!da1469x_clock_is_pll_locked()) { + NVIC_EnableIRQ(PLL_LOCK_IRQn); + while (!NVIC_GetPendingIRQ(PLL_LOCK_IRQn)) { + __WFI(); + } + NVIC_DisableIRQ(PLL_LOCK_IRQn); + } + + __HAL_ENABLE_INTERRUPTS(primask); +} + +void +da1469x_clock_sys_pll_switch(void) +{ + /* CLK_SEL_Msk == 3 means PLL */ + CRG_TOP->CLK_CTRL_REG |= CRG_TOP_CLK_CTRL_REG_SYS_CLK_SEL_Msk; + + while (!(CRG_TOP->CLK_CTRL_REG & CRG_TOP_CLK_CTRL_REG_RUNNING_AT_PLL96M_Msk)); +} diff --git a/hw/mcu/dialog/da1469x/src/hal_gpio.c b/hw/mcu/dialog/da1469x/src/hal_gpio.c new file mode 100644 index 000000000..e105cf2b0 --- /dev/null +++ b/hw/mcu/dialog/da1469x/src/hal_gpio.c @@ -0,0 +1,478 @@ + +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +#include +#include +#include "syscfg/syscfg.h" +#include "mcu/da1469x_hal.h" +#include +#include "hal/hal_gpio.h" + +/* GPIO interrupts */ +#define HAL_GPIO_MAX_IRQ MYNEWT_VAL(MCU_GPIO_MAX_IRQ) + +#define GPIO_REG(name) ((__IO uint32_t *)(GPIO_BASE + offsetof(GPIO_Type, name))) +#define WAKEUP_REG(name) ((__IO uint32_t *)(WAKEUP_BASE + offsetof(WAKEUP_Type, name))) +#define CRG_TOP_REG(name) ((__IO uint32_t *)(CRG_TOP_BASE + offsetof(CRG_TOP_Type, name))) + +#ifndef MCU_GPIO_PORT0_PIN_COUNT +#define MCU_GPIO_PORT0_PIN_COUNT 32 +#endif + +#if (MCU_GPIO_PORT0_PIN_COUNT) == 32 +#define GPIO_PORT(pin) (((unsigned)(pin)) >> 5U) +#define GPIO_PORT_PIN(pin) (((unsigned)(pin)) & 31U) +#else +#define GPIO_PORT(pin) (((unsigned)(pin)) < MCU_GPIO_PORT0_PIN_COUNT ? 0 : 1) +#define GPIO_PORT_PIN(pin) ((unsigned)(pin) < MCU_GPIO_PORT0_PIN_COUNT ? \ + (pin) : (pin) - MCU_GPIO_PORT0_PIN_COUNT) +#endif + +#define GPIO_PIN_BIT(pin) (1 << GPIO_PORT_PIN(pin)) + +#define GPIO_PIN_DATA_REG_ADDR(pin) (GPIO_REG(P0_DATA_REG) + GPIO_PORT(pin)) +#define GPIO_PIN_DATA_REG(pin) *GPIO_PIN_DATA_REG_ADDR(pin) +#define GPIO_PIN_SET_DATA_REG_ADDR(pin) (GPIO_REG(P0_SET_DATA_REG) + GPIO_PORT(pin)) +#define GPIO_PIN_SET_DATA_REG(pin) *GPIO_PIN_SET_DATA_REG_ADDR(pin) +#define GPIO_PIN_RESET_DATA_REG_ADDR(pin) (GPIO_REG(P0_RESET_DATA_REG) + GPIO_PORT(pin)) +#define GPIO_PIN_RESET_DATA_REG(pin) *GPIO_PIN_RESET_DATA_REG_ADDR(pin) +#define GPIO_PIN_MODE_REG_ADDR(pin) (GPIO_REG(P0_00_MODE_REG) + (pin)) +#define GPIO_PIN_MODE_REG(pin) *GPIO_PIN_MODE_REG_ADDR(pin) +#define GPIO_PIN_PADPWR_CTRL_REG_ADDR(pin) (GPIO_REG(P0_PADPWR_CTRL_REG) + GPIO_PORT(pin)) +#define GPIO_PIN_PADPWR_CTRL_REG(pin) *GPIO_PIN_PADPWR_CTRL_REG_ADDR(pin) +#define GPIO_PIN_UNLATCH_ADDR(pin) (CRG_TOP_REG(P0_SET_PAD_LATCH_REG) + GPIO_PORT(pin) * 3) +#define GPIO_PIN_LATCH_ADDR(pin) (CRG_TOP_REG(P0_RESET_PAD_LATCH_REG) + GPIO_PORT(pin) * 3) + +#define WKUP_CTRL_REG_ADDR (WAKEUP_REG(WKUP_CTRL_REG)) +#define WKUP_RESET_IRQ_REG_ADDR (WAKEUP_REG(WKUP_RESET_IRQ_REG)) +#define WKUP_SELECT_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_SELECT_P0_REG) + GPIO_PORT(pin)) +#define WKUP_SELECT_PX_REG(pin) *(WKUP_SELECT_PX_REG_ADDR(pin)) +#define WKUP_POL_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_POL_P0_REG) + GPIO_PORT(pin)) +#define WKUP_POL_PX_SET_FALLING(pin) do { *(WKUP_POL_PX_REG_ADDR(pin)) |= GPIO_PIN_BIT(pin); } while (0) +#define WKUP_POL_PX_SET_RISING(pin) do { *(WKUP_POL_PX_REG_ADDR(pin)) &= ~GPIO_PIN_BIT(pin); } while (0) +#define WKUP_STAT_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_STATUS_P0_REG) + GPIO_PORT(pin)) +#define WKUP_STAT(pin) ((*(WKUP_STAT_PX_REG_ADDR(pin)) >> GPIO_PORT_PIN(pin)) & 1) +#define WKUP_CLEAR_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_CLEAR_P0_REG) + GPIO_PORT(pin)) +#define WKUP_CLEAR_PX(pin) do { (*(WKUP_CLEAR_PX_REG_ADDR(pin)) = GPIO_PIN_BIT(pin)); } while (0) +#define WKUP_SEL_GPIO_PX_REG_ADDR(pin) (WAKEUP_REG(WKUP_SEL_GPIO_P0_REG) + GPIO_PORT(pin)) +#define WKUP_SEL_GPIO_PX_REG(pin) *(WKUP_SEL_GPIO_PX_REG_ADDR(pin)) + +/* Storage for GPIO callbacks. */ +struct hal_gpio_irq { + int pin; + hal_gpio_irq_handler_t func; + void *arg; +}; + +static struct hal_gpio_irq hal_gpio_irqs[HAL_GPIO_MAX_IRQ]; + +#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0 +static uint32_t g_mcu_gpio_latch_state[2]; +static uint8_t g_mcu_gpio_retained_num; +static struct da1469x_retreg g_mcu_gpio_retained[MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM)]; +#endif + +/* + * We assume that any latched pin has default configuration, i.e. was either + * not configured or was deinited. Any unlatched pin is considered to be used + * by someone. + * + * By default, all pins are assumed to have default configuration and are + * latched. This allows PD_COM to be disabled (if no other peripheral needs + * it) since we do not need GPIO mux to be active. + * + * Configuration of any pin shall be done as follows, with interrupts disabled: + * 1. call mcu_gpio_unlatch_prepare() to enable PD_COM if needed + * 2. configure pin + * 3. call mcu_gpio_unlatch() to actually unlatch pin + * + * Once pin is restored to default configuration it shall be latched again by + * calling mcu_gpio_latch(). + */ + +#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0 +static void +mcu_gpio_retained_add_port(uint32_t latch_val, volatile uint32_t *base_reg) +{ + struct da1469x_retreg *retreg; + int pin; + + retreg = &g_mcu_gpio_retained[g_mcu_gpio_retained_num]; + + while (latch_val) { + assert(g_mcu_gpio_retained_num < MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM)); + + pin = __builtin_ctz(latch_val); + latch_val &= ~(1 << pin); + + da1469x_retreg_assign(retreg, &base_reg[pin]); + + g_mcu_gpio_retained_num++; + retreg++; + } +} +#endif + +static void +mcu_gpio_retained_refresh(void) +{ +#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0 + g_mcu_gpio_retained_num = 0; + + mcu_gpio_retained_add_port(CRG_TOP->P0_PAD_LATCH_REG, &GPIO->P0_00_MODE_REG); + mcu_gpio_retained_add_port(CRG_TOP->P1_PAD_LATCH_REG, &GPIO->P1_00_MODE_REG); +#endif +} + +static inline void +mcu_gpio_unlatch_prepare(int pin) +{ + __HAL_ASSERT_CRITICAL(); + (void)pin; + + /* Acquire PD_COM if first pin will be unlatched */ +// if ((CRG_TOP->P0_PAD_LATCH_REG | CRG_TOP->P1_PAD_LATCH_REG) == 0) { +// da1469x_pd_acquire(MCU_PD_DOMAIN_COM); +// } +} + +static inline void +mcu_gpio_unlatch(int pin) +{ + __HAL_ASSERT_CRITICAL(); + + *GPIO_PIN_UNLATCH_ADDR(pin) = GPIO_PIN_BIT(pin); + mcu_gpio_retained_refresh(); +} + +static inline void +mcu_gpio_latch(int pin) +{ + (void)pin; +// uint32_t primask; +// uint32_t latch_pre; +// uint32_t latch_post; +// +// __HAL_DISABLE_INTERRUPTS(primask); +// +// latch_pre = CRG_TOP->P0_PAD_LATCH_REG | CRG_TOP->P1_PAD_LATCH_REG; +// +// *GPIO_PIN_LATCH_ADDR(pin) = GPIO_PIN_BIT(pin); +// mcu_gpio_retained_refresh(); +// +// latch_post = CRG_TOP->P0_PAD_LATCH_REG | CRG_TOP->P1_PAD_LATCH_REG; +// +// /* Release PD_COM if last pin was latched */ +// if (latch_pre && !latch_post) { +// da1469x_pd_release(MCU_PD_DOMAIN_COM); +// } +// +// __HAL_ENABLE_INTERRUPTS(primask); +} + +int +hal_gpio_init_in(int pin, hal_gpio_pull_t pull) +{ + volatile uint32_t *px_xx_mod_reg = GPIO_PIN_MODE_REG_ADDR(pin); + uint32_t regval; + uint32_t primask; + + switch (pull) { + case HAL_GPIO_PULL_UP: + regval = MCU_GPIO_FUNC_GPIO | MCU_GPIO_MODE_INPUT_PULLUP; + break; + case HAL_GPIO_PULL_DOWN: + regval = MCU_GPIO_FUNC_GPIO | MCU_GPIO_MODE_INPUT_PULLDOWN; + break; + case HAL_GPIO_PULL_NONE: + regval = MCU_GPIO_FUNC_GPIO | MCU_GPIO_MODE_INPUT; + break; + default: + return -1; + } + + __HAL_DISABLE_INTERRUPTS(primask); + + mcu_gpio_unlatch_prepare(pin); + + *px_xx_mod_reg = regval; + + mcu_gpio_unlatch(pin); + + __HAL_ENABLE_INTERRUPTS(primask); + + return 0; +} + +int +hal_gpio_init_out(int pin, int val) +{ + uint32_t primask; + + __HAL_DISABLE_INTERRUPTS(primask); + + mcu_gpio_unlatch_prepare(pin); + + GPIO_PIN_MODE_REG(pin) = MCU_GPIO_MODE_OUTPUT; + + if (val) { + GPIO_PIN_SET_DATA_REG(pin) = GPIO_PIN_BIT(pin); + } else { + GPIO_PIN_RESET_DATA_REG(pin) = GPIO_PIN_BIT(pin); + } + + mcu_gpio_unlatch(pin); + + __HAL_ENABLE_INTERRUPTS(primask); + + return 0; +} + +int +hal_gpio_deinit(int pin) +{ + /* Reset mode to default value and latch pin */ + GPIO_PIN_MODE_REG(pin) = 0x200; + GPIO_PIN_RESET_DATA_REG(pin) = GPIO_PIN_BIT(pin); + + mcu_gpio_latch(pin); + + return 0; +} + +void +hal_gpio_write(int pin, int val) +{ + if (val) { + GPIO_PIN_SET_DATA_REG(pin) = GPIO_PIN_BIT(pin); + } else { + GPIO_PIN_RESET_DATA_REG(pin) = GPIO_PIN_BIT(pin); + } +} + +int +hal_gpio_read(int pin) +{ + return (GPIO_PIN_DATA_REG(pin) >> GPIO_PORT_PIN(pin)) & 1; +} + +int +hal_gpio_toggle(int pin) +{ + int new_value = hal_gpio_read(pin) == 0; + + hal_gpio_write(pin, new_value); + + return new_value; +} + +static void +hal_gpio_irq_handler(void) +{ + struct hal_gpio_irq *irq; + uint32_t stat; + int i; + + *WKUP_RESET_IRQ_REG_ADDR = 1; + NVIC_ClearPendingIRQ(KEY_WKUP_GPIO_IRQn); + + for (i = 0; i < HAL_GPIO_MAX_IRQ; i++) { + irq = &hal_gpio_irqs[i]; + + /* Read latched status value from relevant GPIO port */ + stat = WKUP_STAT(irq->pin); + + if (irq->func && stat) { + irq->func(irq->arg); + } + + WKUP_CLEAR_PX(irq->pin); + } +} + +static void +hal_gpio_irq_setup(void) +{ + static uint8_t irq_setup; + int sr; + + if (!irq_setup) { + __HAL_DISABLE_INTERRUPTS(sr); + + irq_setup = 1; + + NVIC_ClearPendingIRQ(GPIO_P0_IRQn); + NVIC_ClearPendingIRQ(GPIO_P1_IRQn); + NVIC_SetVector(GPIO_P0_IRQn, (uint32_t)hal_gpio_irq_handler); + NVIC_SetVector(GPIO_P1_IRQn, (uint32_t)hal_gpio_irq_handler); + WAKEUP->WKUP_CTRL_REG = 0; + WAKEUP->WKUP_CLEAR_P0_REG = 0xFFFFFFFF; + WAKEUP->WKUP_CLEAR_P1_REG = 0x007FFFFF; + WAKEUP->WKUP_SELECT_P0_REG = 0; + WAKEUP->WKUP_SELECT_P1_REG = 0; + WAKEUP->WKUP_SEL_GPIO_P0_REG = 0; + WAKEUP->WKUP_SEL_GPIO_P1_REG = 0; + WAKEUP->WKUP_RESET_IRQ_REG = 0; + + CRG_TOP->CLK_TMR_REG |= CRG_TOP_CLK_TMR_REG_WAKEUPCT_ENABLE_Msk; + + __HAL_ENABLE_INTERRUPTS(sr); + NVIC_EnableIRQ(GPIO_P0_IRQn); + NVIC_EnableIRQ(GPIO_P1_IRQn); + } +} + +static int +hal_gpio_find_empty_slot(void) +{ + int i; + + for (i = 0; i < HAL_GPIO_MAX_IRQ; i++) { + if (hal_gpio_irqs[i].func == NULL) { + return i; + } + } + + return -1; +} + +int +hal_gpio_irq_init(int pin, hal_gpio_irq_handler_t handler, void *arg, + hal_gpio_irq_trig_t trig, hal_gpio_pull_t pull) +{ + int i; + + hal_gpio_irq_setup(); + + i = hal_gpio_find_empty_slot(); + /* If assert failed increase syscfg value MCU_GPIO_MAX_IRQ */ + assert(i >= 0); + if (i < 0) { + return -1; + } + + hal_gpio_init_in(pin, pull); + + switch (trig) { + case HAL_GPIO_TRIG_RISING: + WKUP_POL_PX_SET_RISING(pin); + break; + case HAL_GPIO_TRIG_FALLING: + WKUP_POL_PX_SET_FALLING(pin); + break; + case HAL_GPIO_TRIG_BOTH: + /* Not supported */ + default: + return -1; + } + + hal_gpio_irqs[i].pin = pin; + hal_gpio_irqs[i].func = handler; + hal_gpio_irqs[i].arg = arg; + + return 0; +} + +void +hal_gpio_irq_release(int pin) +{ + int i; + + hal_gpio_irq_disable(pin); + + for (i = 0; i < HAL_GPIO_MAX_IRQ; i++) { + if (hal_gpio_irqs[i].pin == pin && hal_gpio_irqs[i].func) { + hal_gpio_irqs[i].pin = -1; + hal_gpio_irqs[i].arg = NULL; + hal_gpio_irqs[i].func = NULL; + } + } +} + +void +hal_gpio_irq_enable(int pin) +{ + WKUP_SEL_GPIO_PX_REG(pin) |= GPIO_PIN_BIT(pin); +} + +void +hal_gpio_irq_disable(int pin) +{ + WKUP_SEL_GPIO_PX_REG(pin) &= ~GPIO_PIN_BIT(pin); + WKUP_CLEAR_PX(pin); +} + +void +mcu_gpio_set_pin_function(int pin, int mode, mcu_gpio_func func) +{ + uint32_t primask; + + __HAL_DISABLE_INTERRUPTS(primask); + + mcu_gpio_unlatch_prepare(pin); + + GPIO_PIN_MODE_REG(pin) = (func & GPIO_P0_00_MODE_REG_PID_Msk) | + (mode & (GPIO_P0_00_MODE_REG_PUPD_Msk | GPIO_P0_00_MODE_REG_PPOD_Msk)); + + mcu_gpio_unlatch(pin); + + __HAL_ENABLE_INTERRUPTS(primask); +} + +void +mcu_gpio_enter_sleep(void) +{ +#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0 + if (g_mcu_gpio_retained_num == 0) { + return; + } + + g_mcu_gpio_latch_state[0] = CRG_TOP->P0_PAD_LATCH_REG; + g_mcu_gpio_latch_state[1] = CRG_TOP->P1_PAD_LATCH_REG; + + da1469x_retreg_update(g_mcu_gpio_retained, g_mcu_gpio_retained_num); + + CRG_TOP->P0_RESET_PAD_LATCH_REG = CRG_TOP_P0_PAD_LATCH_REG_P0_LATCH_EN_Msk; + CRG_TOP->P1_RESET_PAD_LATCH_REG = CRG_TOP_P1_PAD_LATCH_REG_P1_LATCH_EN_Msk; + + da1469x_pd_release(MCU_PD_DOMAIN_COM); +#endif +} + +void +mcu_gpio_exit_sleep(void) +{ +#if MYNEWT_VAL(MCU_GPIO_RETAINABLE_NUM) >= 0 + if (g_mcu_gpio_retained_num == 0) { + return; + } + + da1469x_pd_acquire(MCU_PD_DOMAIN_COM); + + da1469x_retreg_restore(g_mcu_gpio_retained, g_mcu_gpio_retained_num); + + /* Set pins states to their latched values */ + GPIO->P0_DATA_REG = GPIO->P0_DATA_REG; + GPIO->P1_DATA_REG = GPIO->P1_DATA_REG; + + CRG_TOP->P0_PAD_LATCH_REG = g_mcu_gpio_latch_state[0]; + CRG_TOP->P1_PAD_LATCH_REG = g_mcu_gpio_latch_state[1]; +#endif +} diff --git a/hw/mcu/dialog/da1469x/src/hal_system.c b/hw/mcu/dialog/da1469x/src/hal_system.c new file mode 100644 index 000000000..2841979f8 --- /dev/null +++ b/hw/mcu/dialog/da1469x/src/hal_system.c @@ -0,0 +1,136 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +#include +#include "syscfg/syscfg.h" +#include "mcu/da1469x_clock.h" +#include "mcu/da1469x_lpclk.h" +#include "mcu/da1469x_pd.h" +#include "mcu/da1469x_pdc.h" +#include "mcu/da1469x_prail.h" +#include "hal/hal_system.h" +#include "os/os_cputime.h" + +#if !MYNEWT_VAL(BOOT_LOADER) +static enum hal_reset_reason g_hal_reset_reason; +#endif + +void +hal_system_init(void) +{ +#if MYNEWT_VAL(MCU_DCDC_ENABLE) + da1469x_prail_dcdc_enable(); +#endif + + /* + * RESET_STAT_REG has to be cleared to allow HW set bits during next reset + * so we should read it now and keep result for application to check at any + * time. This does not happen for bootloader since reading reset reason in + * bootloader would prevent application from reading it. + */ + +#if !MYNEWT_VAL(BOOT_LOADER) + uint32_t reg; + + reg = CRG_TOP->RESET_STAT_REG; + CRG_TOP->RESET_STAT_REG = 0; + + if (reg & CRG_TOP_RESET_STAT_REG_PORESET_STAT_Msk) { + g_hal_reset_reason = HAL_RESET_POR; + } else if (reg & CRG_TOP_RESET_STAT_REG_WDOGRESET_STAT_Msk) { + g_hal_reset_reason = HAL_RESET_WATCHDOG; + } else if (reg & CRG_TOP_RESET_STAT_REG_SWRESET_STAT_Msk) { + g_hal_reset_reason = HAL_RESET_SOFT; + } else if (reg & CRG_TOP_RESET_STAT_REG_HWRESET_STAT_Msk) { + g_hal_reset_reason = HAL_RESET_PIN; + } else { + g_hal_reset_reason = 0; + } +#endif +} + +void +hal_system_reset(void) +{ + +#if MYNEWT_VAL(HAL_SYSTEM_RESET_CB) + hal_system_reset_cb(); +#endif + + while (1) { + HAL_DEBUG_BREAK(); + CRG_TOP->SYS_CTRL_REG = 0x20; + NVIC_SystemReset(); + } +} + +int +hal_debugger_connected(void) +{ + return CRG_TOP->SYS_STAT_REG & CRG_TOP_SYS_STAT_REG_DBG_IS_ACTIVE_Msk; +} + +void +hal_system_clock_start(void) +{ + /* Reset clock dividers to 0 */ + CRG_TOP->CLK_AMBA_REG &= ~(CRG_TOP_CLK_AMBA_REG_HCLK_DIV_Msk | CRG_TOP_CLK_AMBA_REG_PCLK_DIV_Msk); + + /* PD_TIM is already started in SystemInit */ + + da1469x_clock_sys_xtal32m_init(); + da1469x_clock_sys_xtal32m_enable(); +#if MYNEWT_VAL(MCU_PLL_ENABLE) + da1469x_clock_sys_pll_enable(); +#endif +#if MYNEWT_VAL_CHOICE(MCU_SYSCLK_SOURCE, PLL96) + da1469x_clock_pll_wait_to_lock(); + da1469x_clock_sys_pll_switch(); +#endif +#if MYNEWT_VAL_CHOICE(MCU_SYSCLK_SOURCE, XTAL32M) + /* Switch to XTAL32M and disable RC32M */ + da1469x_clock_sys_xtal32m_switch_safe(); +#endif + da1469x_clock_sys_rc32m_disable(); + +#if MYNEWT_VAL_CHOICE(MCU_LPCLK_SOURCE, RCX) + /* Switch to RCX and calibrate it */ + da1469x_clock_lp_rcx_enable(); + da1469x_clock_lp_rcx_switch(); + da1469x_clock_lp_rcx_calibrate(); + da1469x_lpclk_enabled(); +#else + /* + * We cannot switch lp_clk to XTAL32K here since it needs some time to + * settle, so we just disable RCX (we don't need it) and then we'll handle + * switch to XTAL32K from sysinit since we need os_cputime for this. + */ + da1469x_clock_lp_rcx_disable(); +#endif +} + +enum hal_reset_reason +hal_reset_cause(void) +{ +#if MYNEWT_VAL(BOOT_LOADER) + return 0; +#else + return g_hal_reset_reason; +#endif +} diff --git a/hw/mcu/dialog/da1469x/src/hal_system_start.c b/hw/mcu/dialog/da1469x/src/hal_system_start.c new file mode 100644 index 000000000..bd2465042 --- /dev/null +++ b/hw/mcu/dialog/da1469x/src/hal_system_start.c @@ -0,0 +1,177 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +#include +#include +#include "mcu/mcu.h" +#include "mcu/da1469x_hal.h" +#include +#include +#if MCUBOOT_MYNEWT +#include "bootutil/bootutil.h" +#include "bootutil/image.h" +#include "bootutil/bootutil_log.h" +#include "mcu/da1469x_dma.h" +#include "mcu/da1469x_otp.h" +#endif + +#if MYNEWT_VAL(BOOT_CUSTOM_START) && MCUBOOT_MYNEWT +sec_text_ram_core +#endif +void __attribute__((naked)) +hal_system_start(void *img_start) +{ + uint32_t img_data_addr; + uint32_t *img_data; + + img_data_addr = MCU_MEM_QSPIF_M_START_ADDRESS + (uint32_t)img_start; + + assert(img_data_addr < MCU_MEM_QSPIF_M_END_ADDRESS); + + img_data = (uint32_t *)img_data_addr; + + asm volatile (".syntax unified \n" + /* 1st word is stack pointer */ + " msr msp, %0 \n" + /* 2nd word is a reset handler (image entry) */ + " bx %1 \n" + : /* no output */ + : "r" (img_data[0]), "r" (img_data[1])); +} + +void +hal_system_restart(void *img_start) +{ + uint32_t primask __attribute__((unused)); + int i; + + /* + * Disable interrupts, and leave them disabled. + * They get re-enabled when system starts coming back again. + */ + __HAL_DISABLE_INTERRUPTS(primask); + + for (i = 0; i < sizeof(NVIC->ICER) / sizeof(NVIC->ICER[0]); i++) { + NVIC->ICER[i] = 0xffffffff; + } + + hal_system_start(img_start); +} + +#if MYNEWT_VAL(BOOT_CUSTOM_START) && MCUBOOT_MYNEWT +#define IMAGE_TLV_AES_NONCE 0x50 +#define IMAGE_TLV_SECRET_ID 0x60 + +sec_text_ram_core void +boot_custom_start(uintptr_t flash_base, struct boot_rsp *rsp) +{ + int rc; + struct image_tlv_iter it; + const struct flash_area *fap; + uint32_t off; + uint16_t len; + uint16_t type; + uint8_t buf[8]; + uint8_t key; + uint32_t nonce[2]; + bool has_aes_nonce; + bool has_secret_id; + DMA_Type *dma_regs = DMA; + uint32_t jump_offset = rsp->br_image_off + rsp->br_hdr->ih_hdr_size; + + BOOT_LOG_INF("Custom initialization"); + + /* skip to booting if we are running nonsecure mode */ + if (!(CRG_TOP->SECURE_BOOT_REG & 0x1)) { + hal_system_start((void *)(flash_base + jump_offset)); + } + + rc = flash_area_open(flash_area_id_from_image_slot(0), &fap); + assert(rc == 0); + + rc = bootutil_tlv_iter_begin(&it, rsp->br_hdr, fap, IMAGE_TLV_ANY, true); + assert(rc == 0); + + has_aes_nonce = has_secret_id = false; + while (true) { + rc = bootutil_tlv_iter_next(&it, &off, &len, &type); + assert(rc >= 0); + + if (rc > 0) { + break; + } + + if (type == IMAGE_TLV_AES_NONCE) { + assert(len == 8); + + rc = flash_area_read(fap, off, buf, len); + assert(rc == 0); + + nonce[0] = __builtin_bswap32(*(uint32_t *)buf); + nonce[1] = __builtin_bswap32(*(uint32_t *)(buf + 4)); + has_aes_nonce = true; + } else if (type == IMAGE_TLV_SECRET_ID) { + assert(len == 4); + + rc = flash_area_read(fap, off, buf, len); + assert(rc == 0); + + key = buf[0]; + has_secret_id = true; + } + } + + assert(has_aes_nonce && has_secret_id && key <= 7); + + /* enable OTP clock and set in read mode */ + da1469x_clock_amba_enable(CRG_TOP_CLK_AMBA_REG_OTP_ENABLE_Msk); + da1469x_otp_set_mode(OTPC_MODE_READ); + + /* disable decrypt on the fly and program start and end addresses */ + QSPIC->QSPIC_CTR_CTRL_REG = 0; + QSPIC->QSPIC_CTR_SADDR_REG = jump_offset; + QSPIC->QSPIC_CTR_EADDR_REG = QSPIC->QSPIC_CTR_SADDR_REG + + rsp->br_hdr->ih_img_size - 1; + + /* securely DMA hardware key from secret storage to QSPI decrypt engine */ + dma_regs->DMA_REQ_MUX_REG |= 0xf000; + dma_regs->DMA7_LEN_REG = 8; + dma_regs->DMA7_A_START_REG = MCU_OTPM_BASE + OTP_SEGMENT_QSPI_FW_KEYS + + (32 * key); + dma_regs->DMA7_B_START_REG = (uint32_t)&QSPIC->QSPIC_CTR_KEY_0_3_REG; + dma_regs->DMA7_CTRL_REG = DMA_DMA7_CTRL_REG_AINC_Msk | + DMA_DMA7_CTRL_REG_BINC_Msk | + (MCU_DMA_BUS_WIDTH_4B << DMA_DMA7_CTRL_REG_BW_Pos) | + DMA_DMA7_CTRL_REG_DMA_ON_Msk; + while (dma_regs->DMA7_IDX_REG != 8); + + /* program NONCE */ + QSPIC->QSPIC_CTR_NONCE_0_3_REG = nonce[0]; + QSPIC->QSPIC_CTR_NONCE_4_7_REG = nonce[1]; + + /* turn back on decrypt on the fly */ + QSPIC->QSPIC_CTR_CTRL_REG = 1; + + /* set OTP to standby and turn off clock */ + da1469x_otp_set_mode(OTPC_MODE_STBY); + da1469x_clock_amba_disable(CRG_TOP_CLK_AMBA_REG_OTP_ENABLE_Msk); + + hal_system_start((void *)(flash_base + jump_offset)); +} +#endif diff --git a/hw/mcu/dialog/da1469x/src/system_da1469x.c b/hw/mcu/dialog/da1469x/src/system_da1469x.c new file mode 100644 index 000000000..538bac79f --- /dev/null +++ b/hw/mcu/dialog/da1469x/src/system_da1469x.c @@ -0,0 +1,61 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +#include "mcu/mcu.h" +#include + +extern uint8_t __StackLimit; + +uint32_t SystemCoreClock = 32000000; + +void +SystemInit(void) +{ + /* Enable FPU when using hard-float */ +#if (__FPU_USED == 1) + SCB->CPACR |= (3UL << 20) | (3UL << 22); + __DSB(); + __ISB(); +#endif + + /* Freez watchdog */ + GPREG->SET_FREEZE_REG |= GPREG_SET_FREEZE_REG_FRZ_SYS_WDOG_Msk; + /* Initialize power domains (disable radio only) */ + CRG_TOP->PMU_CTRL_REG = CRG_TOP_PMU_CTRL_REG_RADIO_SLEEP_Msk; + + CRG_TOP->P0_SET_PAD_LATCH_REG = CRG_TOP_P0_PAD_LATCH_REG_P0_LATCH_EN_Msk; + CRG_TOP->P1_SET_PAD_LATCH_REG = CRG_TOP_P1_PAD_LATCH_REG_P1_LATCH_EN_Msk; + + /* Reset clock dividers to 0 */ + CRG_TOP->CLK_AMBA_REG &= ~(CRG_TOP_CLK_AMBA_REG_HCLK_DIV_Msk | CRG_TOP_CLK_AMBA_REG_PCLK_DIV_Msk); + + /* PD_TIM is already started in SystemInit */ + + da1469x_clock_sys_xtal32m_init(); + da1469x_clock_sys_xtal32m_enable(); + da1469x_clock_sys_pll_enable(); + da1469x_clock_pll_wait_to_lock(); + /* Switch to XTAL32M and disable RC32M */ + da1469x_clock_sys_xtal32m_switch_safe(); + da1469x_clock_sys_rc32m_disable(); +} + +void _init(void) +{ +} -- cgit v1.3.1 From 50b569ad1be86930ae968655ec574362a2b57aa6 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 29 Jun 2020 16:52:08 +0700 Subject: added esp32s2 kaluga bsp --- docs/boards.md | 1 + examples/device/board_test/CMakeLists.txt | 2 +- examples/device/cdc_msc_freertos/CMakeLists.txt | 2 +- examples/device/hid_composite_freertos/CMakeLists.txt | 2 +- examples/rules.mk | 5 ++--- hw/bsp/esp32s2_saola_1/CMakeLists.txt | 2 +- hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c | 4 ++-- 7 files changed, 9 insertions(+), 9 deletions(-) (limited to 'hw/bsp') diff --git a/docs/boards.md b/docs/boards.md index 202602d30..46d071853 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -11,6 +11,7 @@ This code base already had supported for a handful of following boards (sorted a ### Espressif ESP32-S2 +- [ESP32-S2-Kaluga-1](https://docs.espressif.com/projects/esp-idf/en/latest/esp32s2/hw-reference/esp32s2/user-guide-esp32-s2-kaluga-1-kit.html) - [ESP32-S2-Saola-1](https://docs.espressif.com/projects/esp-idf/en/latest/esp32s2/hw-reference/esp32s2/user-guide-saola-1-v1.2.html) ### MicroChip SAMD diff --git a/examples/device/board_test/CMakeLists.txt b/examples/device/board_test/CMakeLists.txt index 4f0359922..f0437dd04 100644 --- a/examples/device/board_test/CMakeLists.txt +++ b/examples/device/board_test/CMakeLists.txt @@ -7,7 +7,7 @@ set(TOP "../../..") get_filename_component(TOP "${TOP}" REALPATH) # Add example src and bsp directories -set(EXTRA_COMPONENT_DIRS "src" "${TOP}/hw/bsp/esp32s2_saola_1") +set(EXTRA_COMPONENT_DIRS "src" "${TOP}/hw/bsp/${BOARD}") include($ENV{IDF_PATH}/tools/cmake/project.cmake) set(SUPPORTED_TARGETS esp32s2) diff --git a/examples/device/cdc_msc_freertos/CMakeLists.txt b/examples/device/cdc_msc_freertos/CMakeLists.txt index b0e2c2cea..339f43a09 100644 --- a/examples/device/cdc_msc_freertos/CMakeLists.txt +++ b/examples/device/cdc_msc_freertos/CMakeLists.txt @@ -7,7 +7,7 @@ set(TOP "../../..") get_filename_component(TOP "${TOP}" REALPATH) # Add example src and bsp directories -set(EXTRA_COMPONENT_DIRS "src" "${TOP}/hw/bsp/esp32s2_saola_1") +set(EXTRA_COMPONENT_DIRS "src" "${TOP}/hw/bsp/${BOARD}") include($ENV{IDF_PATH}/tools/cmake/project.cmake) set(SUPPORTED_TARGETS esp32s2) diff --git a/examples/device/hid_composite_freertos/CMakeLists.txt b/examples/device/hid_composite_freertos/CMakeLists.txt index bfd0677e0..a429a1336 100644 --- a/examples/device/hid_composite_freertos/CMakeLists.txt +++ b/examples/device/hid_composite_freertos/CMakeLists.txt @@ -7,7 +7,7 @@ set(TOP "../../..") get_filename_component(TOP "${TOP}" REALPATH) # Add example src and bsp directories -set(EXTRA_COMPONENT_DIRS "src" "${TOP}/hw/bsp/esp32s2_saola_1") +set(EXTRA_COMPONENT_DIRS "src" "${TOP}/hw/bsp/${BOARD}") include($ENV{IDF_PATH}/tools/cmake/project.cmake) set(SUPPORTED_TARGETS esp32s2) diff --git a/examples/rules.mk b/examples/rules.mk index 2f4c8b860..eeb548d08 100644 --- a/examples/rules.mk +++ b/examples/rules.mk @@ -12,11 +12,10 @@ all: idf.py -B$(BUILD) -DBOARD=$(BOARD) build clean: - idf.py -B$(BUILD) clean + idf.py -B$(BUILD) -DBOARD=$(BOARD) clean flash: - @:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyUSB0) - idf.py -B$(BUILD) -p $(SERIAL) flash + idf.py -B$(BUILD) -DBOARD=$(BOARD) flash else # GNU Make build system diff --git a/hw/bsp/esp32s2_saola_1/CMakeLists.txt b/hw/bsp/esp32s2_saola_1/CMakeLists.txt index 379b2e3d0..629b3104a 100644 --- a/hw/bsp/esp32s2_saola_1/CMakeLists.txt +++ b/hw/bsp/esp32s2_saola_1/CMakeLists.txt @@ -1,4 +1,4 @@ -idf_component_register(SRCS "esp32s2_saola_1.c" "led_strip/src/led_strip_rmt_ws2812.c" +idf_component_register(SRCS "${BOARD}.c" "led_strip/src/led_strip_rmt_ws2812.c" INCLUDE_DIRS "led_strip/include" PRIV_REQUIRES "driver" REQUIRES freertos src) diff --git a/hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c b/hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c index bbcdab6d2..a30d3c81e 100644 --- a/hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c +++ b/hw/bsp/esp32s2_saola_1/esp32s2_saola_1.c @@ -39,8 +39,8 @@ // Note: On the production version (v1.2) WS2812 is connected to GPIO 18, // however earlier revision v1.1 WS2812 is connected to GPIO 17 -//#define LED_PIN 18 // v1.2 and later -#define LED_PIN 17 // v1.1 +//#define LED_PIN 17 // v1.1 +#define LED_PIN 18 // v1.2 and later #define BUTTON_PIN 0 #define BUTTON_STATE_ACTIVE 0 -- cgit v1.3.1 From 2dff40236cb06a8f1adc1edcdd0524f162472ee5 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 29 Jun 2020 18:40:23 +0700 Subject: add kaluga files --- hw/bsp/esp32s2_kaluga_1/CMakeLists.txt | 16 ++ hw/bsp/esp32s2_kaluga_1/board.mk | 2 + hw/bsp/esp32s2_kaluga_1/esp32s2_kaluga_1.c | 108 +++++++++++++ .../esp32s2_kaluga_1/led_strip/include/led_strip.h | 126 +++++++++++++++ .../led_strip/src/led_strip_rmt_ws2812.c | 171 +++++++++++++++++++++ 5 files changed, 423 insertions(+) create mode 100644 hw/bsp/esp32s2_kaluga_1/CMakeLists.txt create mode 100644 hw/bsp/esp32s2_kaluga_1/board.mk create mode 100644 hw/bsp/esp32s2_kaluga_1/esp32s2_kaluga_1.c create mode 100644 hw/bsp/esp32s2_kaluga_1/led_strip/include/led_strip.h create mode 100644 hw/bsp/esp32s2_kaluga_1/led_strip/src/led_strip_rmt_ws2812.c (limited to 'hw/bsp') diff --git a/hw/bsp/esp32s2_kaluga_1/CMakeLists.txt b/hw/bsp/esp32s2_kaluga_1/CMakeLists.txt new file mode 100644 index 000000000..1627f39a3 --- /dev/null +++ b/hw/bsp/esp32s2_kaluga_1/CMakeLists.txt @@ -0,0 +1,16 @@ +idf_component_register(SRCS "${BOARD}.c" "led_strip/src/led_strip_rmt_ws2812.c" + INCLUDE_DIRS "led_strip/include" + PRIV_REQUIRES "driver" + REQUIRES freertos src) + +target_compile_options(${COMPONENT_TARGET} PUBLIC + "-DCFG_TUSB_MCU=OPT_MCU_ESP32S2" + "-DCFG_TUSB_OS=OPT_OS_FREERTOS" +) + +idf_component_get_property( FREERTOS_ORIG_INCLUDE_PATH freertos ORIG_INCLUDE_PATH) +target_include_directories(${COMPONENT_TARGET} PUBLIC + "${FREERTOS_ORIG_INCLUDE_PATH}" + "${TOP}/hw" + "${TOP}/src" +) diff --git a/hw/bsp/esp32s2_kaluga_1/board.mk b/hw/bsp/esp32s2_kaluga_1/board.mk new file mode 100644 index 000000000..167ef6226 --- /dev/null +++ b/hw/bsp/esp32s2_kaluga_1/board.mk @@ -0,0 +1,2 @@ +# Cross Compiler for ESP32 +CROSS_COMPILE = xtensa-esp32s2-elf- diff --git a/hw/bsp/esp32s2_kaluga_1/esp32s2_kaluga_1.c b/hw/bsp/esp32s2_kaluga_1/esp32s2_kaluga_1.c new file mode 100644 index 000000000..3bf7a5b8a --- /dev/null +++ b/hw/bsp/esp32s2_kaluga_1/esp32s2_kaluga_1.c @@ -0,0 +1,108 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" +#include "driver/gpio.h" +#include "driver/periph_ctrl.h" +#include "hal/usb_hal.h" +#include "soc/usb_periph.h" + +#include "driver/rmt.h" +#include "led_strip/include/led_strip.h" + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM DECLARATION +//--------------------------------------------------------------------+ + +#define LED_PIN 45 + +#define BUTTON_PIN 0 +#define BUTTON_STATE_ACTIVE 0 + + +static led_strip_t *strip; + +// Initialize on-board peripherals : led, button, uart and USB +void board_init(void) +{ + // WS2812 Neopixel driver with RMT peripheral + rmt_config_t config = RMT_DEFAULT_CONFIG_TX(LED_PIN, RMT_CHANNEL_0); + config.clk_div = 2; // set counter clock to 40MHz + + rmt_config(&config); + rmt_driver_install(config.channel, 0, 0); + + led_strip_config_t strip_config = LED_STRIP_DEFAULT_CONFIG(1, (led_strip_dev_t) config.channel); + strip = led_strip_new_rmt_ws2812(&strip_config); + strip->clear(strip, 100); // off led + + // Button + gpio_pad_select_gpio(BUTTON_PIN); + gpio_set_direction(BUTTON_PIN, GPIO_MODE_INPUT); + gpio_set_pull_mode(BUTTON_PIN, BUTTON_STATE_ACTIVE ? GPIO_PULLDOWN_ONLY : GPIO_PULLUP_ONLY); + + // USB Controller Hal init + periph_module_reset(PERIPH_USB_MODULE); + periph_module_enable(PERIPH_USB_MODULE); + + usb_hal_context_t hal = { + .use_external_phy = false // use built-in PHY + }; + usb_hal_init(&hal); + + // Pin drive strength + gpio_set_drive_capability(USBPHY_DM_NUM, GPIO_DRIVE_CAP_3); + gpio_set_drive_capability(USBPHY_DP_NUM, GPIO_DRIVE_CAP_3); +} + +// Turn LED on or off +void board_led_write(bool state) +{ + strip->set_pixel(strip, 0, (state ? 0x88 : 0x00), 0x00, 0x00); + strip->refresh(strip, 100); +} + +// Get the current state of button +// a '1' means active (pressed), a '0' means inactive. +uint32_t board_button_read(void) +{ + return gpio_get_level(BUTTON_PIN) == BUTTON_STATE_ACTIVE; +} + +// Get characters from UART +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +// Send characters to UART +int board_uart_write(void const * buf, int len) +{ + (void) buf; (void) len; + return 0; +} + diff --git a/hw/bsp/esp32s2_kaluga_1/led_strip/include/led_strip.h b/hw/bsp/esp32s2_kaluga_1/led_strip/include/led_strip.h new file mode 100644 index 000000000..a9dffc325 --- /dev/null +++ b/hw/bsp/esp32s2_kaluga_1/led_strip/include/led_strip.h @@ -0,0 +1,126 @@ +// Copyright 2019 Espressif Systems (Shanghai) PTE LTD +// +// Licensed under the Apache License, Version 2.0 (the "License"); +// you may not use this file except in compliance with the License. +// You may obtain a copy of the License at +// +// http://www.apache.org/licenses/LICENSE-2.0 +// +// Unless required by applicable law or agreed to in writing, software +// distributed under the License is distributed on an "AS IS" BASIS, +// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +// See the License for the specific language governing permissions and +// limitations under the License. +#pragma once + +#ifdef __cplusplus +extern "C" { +#endif + +#include "esp_err.h" + +/** +* @brief LED Strip Type +* +*/ +typedef struct led_strip_s led_strip_t; + +/** +* @brief LED Strip Device Type +* +*/ +typedef void *led_strip_dev_t; + +/** +* @brief Declare of LED Strip Type +* +*/ +struct led_strip_s { + /** + * @brief Set RGB for a specific pixel + * + * @param strip: LED strip + * @param index: index of pixel to set + * @param red: red part of color + * @param green: green part of color + * @param blue: blue part of color + * + * @return + * - ESP_OK: Set RGB for a specific pixel successfully + * - ESP_ERR_INVALID_ARG: Set RGB for a specific pixel failed because of invalid parameters + * - ESP_FAIL: Set RGB for a specific pixel failed because other error occurred + */ + esp_err_t (*set_pixel)(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue); + + /** + * @brief Refresh memory colors to LEDs + * + * @param strip: LED strip + * @param timeout_ms: timeout value for refreshing task + * + * @return + * - ESP_OK: Refresh successfully + * - ESP_ERR_TIMEOUT: Refresh failed because of timeout + * - ESP_FAIL: Refresh failed because some other error occurred + * + * @note: + * After updating the LED colors in the memory, a following invocation of this API is needed to flush colors to strip. + */ + esp_err_t (*refresh)(led_strip_t *strip, uint32_t timeout_ms); + + /** + * @brief Clear LED strip (turn off all LEDs) + * + * @param strip: LED strip + * @param timeout_ms: timeout value for clearing task + * + * @return + * - ESP_OK: Clear LEDs successfully + * - ESP_ERR_TIMEOUT: Clear LEDs failed because of timeout + * - ESP_FAIL: Clear LEDs failed because some other error occurred + */ + esp_err_t (*clear)(led_strip_t *strip, uint32_t timeout_ms); + + /** + * @brief Free LED strip resources + * + * @param strip: LED strip + * + * @return + * - ESP_OK: Free resources successfully + * - ESP_FAIL: Free resources failed because error occurred + */ + esp_err_t (*del)(led_strip_t *strip); +}; + +/** +* @brief LED Strip Configuration Type +* +*/ +typedef struct { + uint32_t max_leds; /*!< Maximum LEDs in a single strip */ + led_strip_dev_t dev; /*!< LED strip device (e.g. RMT channel, PWM channel, etc) */ +} led_strip_config_t; + +/** + * @brief Default configuration for LED strip + * + */ +#define LED_STRIP_DEFAULT_CONFIG(number, dev_hdl) \ + { \ + .max_leds = number, \ + .dev = dev_hdl, \ + } + +/** +* @brief Install a new ws2812 driver (based on RMT peripheral) +* +* @param config: LED strip configuration +* @return +* LED strip instance or NULL +*/ +led_strip_t *led_strip_new_rmt_ws2812(const led_strip_config_t *config); + +#ifdef __cplusplus +} +#endif diff --git a/hw/bsp/esp32s2_kaluga_1/led_strip/src/led_strip_rmt_ws2812.c b/hw/bsp/esp32s2_kaluga_1/led_strip/src/led_strip_rmt_ws2812.c new file mode 100644 index 000000000..025d3c590 --- /dev/null +++ b/hw/bsp/esp32s2_kaluga_1/led_strip/src/led_strip_rmt_ws2812.c @@ -0,0 +1,171 @@ +// Copyright 2019 Espressif Systems (Shanghai) PTE LTD +// +// Licensed under the Apache License, Version 2.0 (the "License"); +// you may not use this file except in compliance with the License. +// You may obtain a copy of the License at +// +// http://www.apache.org/licenses/LICENSE-2.0 +// +// Unless required by applicable law or agreed to in writing, software +// distributed under the License is distributed on an "AS IS" BASIS, +// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. +// See the License for the specific language governing permissions and +// limitations under the License. +#include +#include +#include +#include "esp_log.h" +#include "esp_attr.h" +#include "led_strip.h" +#include "driver/rmt.h" + +static const char *TAG = "ws2812"; +#define STRIP_CHECK(a, str, goto_tag, ret_value, ...) \ + do \ + { \ + if (!(a)) \ + { \ + ESP_LOGE(TAG, "%s(%d): " str, __FUNCTION__, __LINE__, ##__VA_ARGS__); \ + ret = ret_value; \ + goto goto_tag; \ + } \ + } while (0) + +#define WS2812_T0H_NS (350) +#define WS2812_T0L_NS (1000) +#define WS2812_T1H_NS (1000) +#define WS2812_T1L_NS (350) +#define WS2812_RESET_US (280) + +static uint32_t ws2812_t0h_ticks = 0; +static uint32_t ws2812_t1h_ticks = 0; +static uint32_t ws2812_t0l_ticks = 0; +static uint32_t ws2812_t1l_ticks = 0; + +typedef struct { + led_strip_t parent; + rmt_channel_t rmt_channel; + uint32_t strip_len; + uint8_t buffer[0]; +} ws2812_t; + +/** + * @brief Conver RGB data to RMT format. + * + * @note For WS2812, R,G,B each contains 256 different choices (i.e. uint8_t) + * + * @param[in] src: source data, to converted to RMT format + * @param[in] dest: place where to store the convert result + * @param[in] src_size: size of source data + * @param[in] wanted_num: number of RMT items that want to get + * @param[out] translated_size: number of source data that got converted + * @param[out] item_num: number of RMT items which are converted from source data + */ +static void IRAM_ATTR ws2812_rmt_adapter(const void *src, rmt_item32_t *dest, size_t src_size, + size_t wanted_num, size_t *translated_size, size_t *item_num) +{ + if (src == NULL || dest == NULL) { + *translated_size = 0; + *item_num = 0; + return; + } + const rmt_item32_t bit0 = {{{ ws2812_t0h_ticks, 1, ws2812_t0l_ticks, 0 }}}; //Logical 0 + const rmt_item32_t bit1 = {{{ ws2812_t1h_ticks, 1, ws2812_t1l_ticks, 0 }}}; //Logical 1 + size_t size = 0; + size_t num = 0; + uint8_t *psrc = (uint8_t *)src; + rmt_item32_t *pdest = dest; + while (size < src_size && num < wanted_num) { + for (int i = 0; i < 8; i++) { + // MSB first + if (*psrc & (1 << (7 - i))) { + pdest->val = bit1.val; + } else { + pdest->val = bit0.val; + } + num++; + pdest++; + } + size++; + psrc++; + } + *translated_size = size; + *item_num = num; +} + +static esp_err_t ws2812_set_pixel(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue) +{ + esp_err_t ret = ESP_OK; + ws2812_t *ws2812 = __containerof(strip, ws2812_t, parent); + STRIP_CHECK(index < ws2812->strip_len, "index out of the maximum number of leds", err, ESP_ERR_INVALID_ARG); + uint32_t start = index * 3; + // In thr order of GRB + ws2812->buffer[start + 0] = green & 0xFF; + ws2812->buffer[start + 1] = red & 0xFF; + ws2812->buffer[start + 2] = blue & 0xFF; + return ESP_OK; +err: + return ret; +} + +static esp_err_t ws2812_refresh(led_strip_t *strip, uint32_t timeout_ms) +{ + esp_err_t ret = ESP_OK; + ws2812_t *ws2812 = __containerof(strip, ws2812_t, parent); + STRIP_CHECK(rmt_write_sample(ws2812->rmt_channel, ws2812->buffer, ws2812->strip_len * 3, true) == ESP_OK, + "transmit RMT samples failed", err, ESP_FAIL); + return rmt_wait_tx_done(ws2812->rmt_channel, pdMS_TO_TICKS(timeout_ms)); +err: + return ret; +} + +static esp_err_t ws2812_clear(led_strip_t *strip, uint32_t timeout_ms) +{ + ws2812_t *ws2812 = __containerof(strip, ws2812_t, parent); + // Write zero to turn off all leds + memset(ws2812->buffer, 0, ws2812->strip_len * 3); + return ws2812_refresh(strip, timeout_ms); +} + +static esp_err_t ws2812_del(led_strip_t *strip) +{ + ws2812_t *ws2812 = __containerof(strip, ws2812_t, parent); + free(ws2812); + return ESP_OK; +} + +led_strip_t *led_strip_new_rmt_ws2812(const led_strip_config_t *config) +{ + led_strip_t *ret = NULL; + STRIP_CHECK(config, "configuration can't be null", err, NULL); + + // 24 bits per led + uint32_t ws2812_size = sizeof(ws2812_t) + config->max_leds * 3; + ws2812_t *ws2812 = calloc(1, ws2812_size); + STRIP_CHECK(ws2812, "request memory for ws2812 failed", err, NULL); + + uint32_t counter_clk_hz = 0; + STRIP_CHECK(rmt_get_counter_clock((rmt_channel_t)config->dev, &counter_clk_hz) == ESP_OK, + "get rmt counter clock failed", err, NULL); + // ns -> ticks + float ratio = (float)counter_clk_hz / 1e9; + ws2812_t0h_ticks = (uint32_t)(ratio * WS2812_T0H_NS); + ws2812_t0l_ticks = (uint32_t)(ratio * WS2812_T0L_NS); + ws2812_t1h_ticks = (uint32_t)(ratio * WS2812_T1H_NS); + ws2812_t1l_ticks = (uint32_t)(ratio * WS2812_T1L_NS); + + // set ws2812 to rmt adapter + rmt_translator_init((rmt_channel_t)config->dev, ws2812_rmt_adapter); + + ws2812->rmt_channel = (rmt_channel_t)config->dev; + ws2812->strip_len = config->max_leds; + + ws2812->parent.set_pixel = ws2812_set_pixel; + ws2812->parent.refresh = ws2812_refresh; + ws2812->parent.clear = ws2812_clear; + ws2812->parent.del = ws2812_del; + + return &ws2812->parent; +err: + return ret; +} -- cgit v1.3.1 From 4b7f848e1fee86e047cfbe2957701c02f1b5fdf2 Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Sun, 21 Jun 2020 17:55:44 +0200 Subject: stm32h743nucleo: Enable Log via STLINK-VCP. --- hw/bsp/stm32h743nucleo/board.mk | 4 +++- hw/bsp/stm32h743nucleo/stm32h743nucleo.c | 34 +++++++++++++++++++++++++---- hw/bsp/stm32h743nucleo/stm32h7xx_hal_conf.h | 3 ++- 3 files changed, 35 insertions(+), 6 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h743nucleo/board.mk b/hw/bsp/stm32h743nucleo/board.mk index 30e52dfcc..43a4999a4 100644 --- a/hw/bsp/stm32h743nucleo/board.mk +++ b/hw/bsp/stm32h743nucleo/board.mk @@ -9,7 +9,8 @@ CFLAGS += \ -DSTM32H743xx \ -DCFG_TUSB_MCU=OPT_MCU_STM32H7 -# mcu driver cause following warnings +# suppress warning caused by vendor mcu driver +CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32H7xx_HAL_Driver ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32H7xx @@ -24,6 +25,7 @@ SRC_C += \ $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc.c \ $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc_ex.c \ $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_uart.c \ $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_pwr_ex.c SRC_S += \ diff --git a/hw/bsp/stm32h743nucleo/stm32h743nucleo.c b/hw/bsp/stm32h743nucleo/stm32h743nucleo.c index bb768eb40..b4a723871 100644 --- a/hw/bsp/stm32h743nucleo/stm32h743nucleo.c +++ b/hw/bsp/stm32h743nucleo/stm32h743nucleo.c @@ -49,14 +49,22 @@ void OTG_FS_IRQHandler(void) #define BUTTON_PIN GPIO_PIN_13 #define BUTTON_STATE_ACTIVE 1 +#define UARTx USART3 +#define UART_GPIO_PORT GPIOD +#define UART_GPIO_AF GPIO_AF7_USART3 +#define UART_TX_PIN GPIO_PIN_8 +#define UART_RX_PIN GPIO_PIN_9 + +UART_HandleTypeDef UartHandle; + // enable all LED, Button, Uart, USB clock static void all_rcc_clk_enable(void) { __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- __HAL_RCC_GPIOB_CLK_ENABLE(); // LED __HAL_RCC_GPIOC_CLK_ENABLE(); // Button -// __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx -// __HAL_RCC_USART3_CLK_ENABLE(); // Uart module + __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx + __HAL_RCC_USART3_CLK_ENABLE(); // Uart module } /* PWR, RCC, GPIO (All): AHB4 (D3 domain) @@ -170,6 +178,24 @@ void board_init(void) GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UARTx; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&UartHandle); + // USB Pin Init // PA9- VUSB, PA10- ID, PA11- DM, PA12- DP @@ -226,8 +252,8 @@ int board_uart_read(uint8_t* buf, int len) int board_uart_write(void const * buf, int len) { - (void) buf; (void) len; - return 0; + HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + return len; } diff --git a/hw/bsp/stm32h743nucleo/stm32h7xx_hal_conf.h b/hw/bsp/stm32h743nucleo/stm32h7xx_hal_conf.h index c58fdf75b..8548ca246 100644 --- a/hw/bsp/stm32h743nucleo/stm32h7xx_hal_conf.h +++ b/hw/bsp/stm32h743nucleo/stm32h7xx_hal_conf.h @@ -100,7 +100,7 @@ /* #define HAL_SRAM_MODULE_ENABLED */ /* #define HAL_SWPMI_MODULE_ENABLED */ /* #define HAL_TIM_MODULE_ENABLED */ -/* #define HAL_UART_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED */ /* #define HAL_USART_MODULE_ENABLED */ /* #define HAL_WWDG_MODULE_ENABLED */ @@ -211,6 +211,7 @@ #define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ #define USE_HAL_SWPMI_REGISTER_CALLBACKS 0U /* SWPMI register callback disabled */ #define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ #define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ /* ########################### Ethernet Configuration ######################### */ -- cgit v1.3.1 From f6660c39a19dda4f4b3c00ce007dfd3e9fd47d7f Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Sun, 21 Jun 2020 20:53:52 +0200 Subject: Add Stm32F7xxdisco board support files Status with examples/device/cdc_msc: - make BOARD=stm32f723disco => OK - make BOARD=stm32f723disco PORT=1 => No Reaction - make BOARD=stm32f746disco => OK - make BOARD=stm32f746disco PORT=1 => Hangs during enumeration - make BOARD=stm32f769disco => Hangs during enumeration --- examples/readme.md | 4 + hw/bsp/stm32f723disco/STM32F723xE_FLASH.ld | 167 ++++++++++ hw/bsp/stm32f723disco/board.mk | 59 ++++ hw/bsp/stm32f723disco/stm32f723disco.c | 300 +++++++++++++++++ hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h | 472 +++++++++++++++++++++++++++ hw/bsp/stm32f746disco/STM32F746ZGTx_FLASH.ld | 167 ++++++++++ hw/bsp/stm32f746disco/board.mk | 59 ++++ hw/bsp/stm32f746disco/stm32f746disco.c | 353 ++++++++++++++++++++ hw/bsp/stm32f746disco/stm32f7xx_hal_conf.h | 472 +++++++++++++++++++++++++++ hw/bsp/stm32f769disco/STM32F769ZITx_FLASH.ld | 167 ++++++++++ hw/bsp/stm32f769disco/board.mk | 51 +++ hw/bsp/stm32f769disco/stm32f769disco.c | 297 +++++++++++++++++ hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h | 472 +++++++++++++++++++++++++++ 13 files changed, 3040 insertions(+) create mode 100644 hw/bsp/stm32f723disco/STM32F723xE_FLASH.ld create mode 100644 hw/bsp/stm32f723disco/board.mk create mode 100644 hw/bsp/stm32f723disco/stm32f723disco.c create mode 100644 hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h create mode 100644 hw/bsp/stm32f746disco/STM32F746ZGTx_FLASH.ld create mode 100644 hw/bsp/stm32f746disco/board.mk create mode 100644 hw/bsp/stm32f746disco/stm32f746disco.c create mode 100644 hw/bsp/stm32f746disco/stm32f7xx_hal_conf.h create mode 100644 hw/bsp/stm32f769disco/STM32F769ZITx_FLASH.ld create mode 100644 hw/bsp/stm32f769disco/board.mk create mode 100644 hw/bsp/stm32f769disco/stm32f769disco.c create mode 100644 hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h (limited to 'hw/bsp') diff --git a/examples/readme.md b/examples/readme.md index ca28d4881..790427cd2 100644 --- a/examples/readme.md +++ b/examples/readme.md @@ -37,6 +37,10 @@ To compile for debugging with debug symbols add DEBUG=1, for example ``` $ make BOARD=feather_nrf52840_express DEBUG=1 all +If a board has several ports, one port is choosen by default in the individual board.mk file. Choose another port with PORT=x. For example to select the HS port of a STM32F746Disco board, use: + +``` +$ make BOARD=stm32f746disco PORT=1 all ``` ### Debug Log diff --git a/hw/bsp/stm32f723disco/STM32F723xE_FLASH.ld b/hw/bsp/stm32f723disco/STM32F723xE_FLASH.ld new file mode 100644 index 000000000..8645ce5c5 --- /dev/null +++ b/hw/bsp/stm32f723disco/STM32F723xE_FLASH.ld @@ -0,0 +1,167 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F723xE Device with +** 512KByte FLASH, 256KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20040000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x460; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 256K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 512K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/stm32f723disco/board.mk b/hw/bsp/stm32f723disco/board.mk new file mode 100644 index 000000000..2bd3b0756 --- /dev/null +++ b/hw/bsp/stm32f723disco/board.mk @@ -0,0 +1,59 @@ +PORT ?= 0 + +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m7 \ + -mfloat-abi=hard \ + -mfpu=fpv5-d16 \ + -nostdlib -nostartfiles \ + -DSTM32F723xx \ + -DHSE_VALUE=25000000 \ + -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ + -DBOARD_DEVICE_RHPORT_NUM=$(PORT) + +ifeq ($(PORT), 1) +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED +$(info "PORT1 HS") +else +$(info "PORT0") +endif + +# mcu driver cause following warnings +CFLAGS += -Wno-error=shadow -Wno-error=cast-align + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F7xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F7xx + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/STM32F723xE_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32f7xx.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_uart.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_pwr_ex.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f723xx.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = synopsys + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM7/r0p1 + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32f723disco/stm32f723disco.c b/hw/bsp/stm32f723disco/stm32f723disco.c new file mode 100644 index 000000000..03057edc7 --- /dev/null +++ b/hw/bsp/stm32f723disco/stm32f723disco.c @@ -0,0 +1,300 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020 Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de), + * Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32f7xx_hal.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void OTG_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +// Despite being call USB2_OTG +// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port +void OTG_HS_IRQHandler(void) +{ + tud_int_handler(1); +} + + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PORT GPIOB +#define LED_PIN GPIO_PIN_1 +#define LED_STATE_ON 1 + +#define BUTTON_PORT GPIOA +#define BUTTON_PIN GPIO_PIN_0 +#define BUTTON_STATE_ACTIVE 1 + +#define UARTx USART6 +#define UART_GPIO_PORT GPIOC +#define UART_GPIO_AF GPIO_AF8_USART6 +#define UART_TX_PIN GPIO_PIN_6 +#define UART_RX_PIN GPIO_PIN_7 + +UART_HandleTypeDef UartHandle; + +// enable all LED, Button, Uart, USB clock +static void all_rcc_clk_enable(void) +{ + __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- + __HAL_RCC_GPIOB_CLK_ENABLE(); // LED, OTG_HS + __HAL_RCC_GPIOC_CLK_ENABLE(); // Button + __HAL_RCC_GPIOD_CLK_ENABLE(); // Uart tx, rx + __HAL_RCC_USART6_CLK_ENABLE(); // Uart module +} + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSE) + * SYSCLK(Hz) = 216000000 + * HCLK(Hz) = 216000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 4 + * APB2 Prescaler = 2 + * HSE Frequency(Hz) = 25000000 + * PLL_M = HSE_VALUE/1000000 + * PLL_N = 432 + * PLL_P = 2 + * PLL_Q = 9 + * VDD(V) = 3.3 + * Main regulator output voltage = Scale1 mode + * Flash Latency(WS) = 7 + * The USB clock configuration from PLLSAI: + * PLLSAIP = 8 + * PLLSAIN = 384 + * PLLSAIQ = 7 + * @param None + * @retval None + */ +void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* Enable Power Control clock */ + __HAL_RCC_PWR_CLK_ENABLE(); + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; + RCC_OscInitStruct.PLL.PLLN = 432; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 9; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Activate the OverDrive to reach the 216 MHz Frequency */ + HAL_PWREx_EnableOverDrive(); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); +} + +void board_init(void) +{ + + + SystemClock_Config(); + all_rcc_clk_enable(); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#endif + + GPIO_InitTypeDef GPIO_InitStruct; + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UARTx; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&UartHandle); + +#if BOARD_DEVICE_RHPORT_NUM == 0 + /* Configure USB FS GPIOs */ + /* Configure DM DP Pins */ + GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure VBUS Pin */ + GPIO_InitStruct.Pin = GPIO_PIN_9; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure OTG-FS ID pin */ + GPIO_InitStruct.Pin = GPIO_PIN_10; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Enable USB FS Clocks */ + __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); + + // Enable VBUS sense (B device) via pin PA9 + USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; + +#else + /* Configure USB HS GPIOs */ + /* Configure DM DP Pins */ + GPIO_InitStruct.Pin = (GPIO_PIN_14 | GPIO_PIN_15); + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + // Enable HS VBUS sense (B device) via pin PB13 + USB_OTG_HS->GCCFG |= USB_OTG_GCCFG_VBDEN; + + /* Configure OTG-HS ID pin */ + GPIO_InitStruct.Pin = GPIO_PIN_13; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOD, &GPIO_InitStruct); + + /* Enable USB HS Clocks */ + __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); + + // Enable VBUS sense (B device) via pin PA9 + USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // B-peripheral session valid override enable + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + + // Force device mode + USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; + USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; + +#endif +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + return HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h b/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h new file mode 100644 index 000000000..03dec8f0d --- /dev/null +++ b/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h @@ -0,0 +1,472 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_CONF_H +#define __STM32F7xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/* #define HAL_ADC_MODULE_ENABLED */ +/* #define HAL_CAN_MODULE_ENABLED */ +/* #define HAL_CAN_LEGACY_MODULE_ENABLED */ +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_DCMI_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_HASH_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_LTDC_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SAI_MODULE_ENABLED */ +/* #define HAL_SD_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +/* #define HAL_SPI_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +/* #define HAL_PCD_MODULE_ENABLED */ +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +/* #define HAL_DSI_MODULE_ENABLED */ +/* #define HAL_JPEG_MODULE_ENABLED */ +/* #define HAL_MDIOS_MODULE_ENABLED */ + + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x0FU) /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 1U +#define ART_ACCLERATOR_ENABLE 1U /* To enable instruction cache and prefetch */ + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIOS register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + +/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ +/* LAN8742A PHY Address*/ +#define LAN8742A_PHY_ADDRESS 0x00 +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY ((uint32_t)0x00000FFF) +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) + +#define PHY_READ_TO ((uint32_t)0x0000FFFF) +#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ + +#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */ + +#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */ + + +#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */ +#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 1U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f7xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f7xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f7xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f7xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f7xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f7xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED + #include "stm32f7xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32f7xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f7xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32f7xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32f7xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f7xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32f7xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32f7xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f7xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32f7xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32f7xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32f7xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f7xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f7xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f7xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED + #include "stm32f7xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED + #include "stm32f7xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f7xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32f7xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32f7xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f7xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32f7xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32f7xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32f7xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f7xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f7xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f7xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f7xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f7xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f7xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f7xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f7xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32f7xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32f7xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32f7xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_JPEG_MODULE_ENABLED + #include "stm32f7xx_hal_jpeg.h" +#endif /* HAL_JPEG_MODULE_ENABLED */ + +#ifdef HAL_MDIOS_MODULE_ENABLED + #include "stm32f7xx_hal_mdios.h" +#endif /* HAL_MDIOS_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F7xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/hw/bsp/stm32f746disco/STM32F746ZGTx_FLASH.ld b/hw/bsp/stm32f746disco/STM32F746ZGTx_FLASH.ld new file mode 100644 index 000000000..045ec76f9 --- /dev/null +++ b/hw/bsp/stm32f746disco/STM32F746ZGTx_FLASH.ld @@ -0,0 +1,167 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F746ZGTx Device with +** 1024KByte FLASH, 320KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20050000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x460; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 320K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 1024K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/stm32f746disco/board.mk b/hw/bsp/stm32f746disco/board.mk new file mode 100644 index 000000000..76a54cdfd --- /dev/null +++ b/hw/bsp/stm32f746disco/board.mk @@ -0,0 +1,59 @@ +PORT ?= 0 + +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m7 \ + -mfloat-abi=hard \ + -mfpu=fpv5-d16 \ + -nostdlib -nostartfiles \ + -DSTM32F746xx \ + -DHSE_VALUE=25000000 \ + -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ + -DBOARD_DEVICE_RHPORT_NUM=$(PORT) + +ifeq ($(PORT), 1) +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED +$(info "PORT1 HS") +else +$(info "PORT0") +endif + +# mcu driver cause following warnings +CFLAGS += -Wno-error=shadow -Wno-error=cast-align + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F7xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F7xx + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/STM32F746ZGTx_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32f7xx.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_uart.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_pwr_ex.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f746xx.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = synopsys + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM7/r0p1 + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32f746disco/stm32f746disco.c b/hw/bsp/stm32f746disco/stm32f746disco.c new file mode 100644 index 000000000..c90182fcf --- /dev/null +++ b/hw/bsp/stm32f746disco/stm32f746disco.c @@ -0,0 +1,353 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020 Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de), + * Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32f7xx_hal.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ + +// Despite being call USB2_OTG +// OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port +void OTG_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +// Despite being call USB2_OTG +// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port +void OTG_HS_IRQHandler(void) +{ + tud_int_handler(1); +} + + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PORT GPIOI +#define LED_PIN GPIO_PIN_1 +#define LED_STATE_ON 1 + +#define BUTTON_PORT GPIOI +#define BUTTON_PIN GPIO_PIN_11 +#define BUTTON_STATE_ACTIVE 1 + +#define UARTx USART1 +#define UART_TX_GPIO_PORT GPIOA +#define UART_RX_GPIO_PORT GPIOB +#define UART_TX_GPIO_AF GPIO_AF7_USART1 +#define UART_RX_GPIO_AF GPIO_AF7_USART1 +#define UART_TX_PIN GPIO_PIN_9 +#define UART_RX_PIN GPIO_PIN_7 + +UART_HandleTypeDef UartHandle; + +// enable all LED, Button, Uart, USB clock +static void all_rcc_clk_enable(void) +{ + __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- + __HAL_RCC_GPIOB_CLK_ENABLE(); // Uart rx + __HAL_RCC_GPIOI_CLK_ENABLE(); // Button + __HAL_RCC_USART1_CLK_ENABLE(); // Uart module +} + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSE) + * SYSCLK(Hz) = 216000000 + * HCLK(Hz) = 216000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 4 + * APB2 Prescaler = 2 + * HSE Frequency(Hz) = 25000000 + * PLL_M = HSE_VALUE/1000000 + * PLL_N = 432 + * PLL_P = 2 + * PLL_Q = 9 + * VDD(V) = 3.3 + * Main regulator output voltage = Scale1 mode + * Flash Latency(WS) = 7 + * The USB clock configuration from PLLSAI: + * PLLSAIP = 8 + * PLLSAIN = 384 + * PLLSAIQ = 7 + * @param None + * @retval None + */ +void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* Enable Power Control clock */ + __HAL_RCC_PWR_CLK_ENABLE(); + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; + RCC_OscInitStruct.PLL.PLLN = 432; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 9; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Activate the OverDrive to reach the 216 MHz Frequency */ + HAL_PWREx_EnableOverDrive(); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); +} + +void board_init(void) +{ + + + SystemClock_Config(); + all_rcc_clk_enable(); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#endif + + GPIO_InitTypeDef GPIO_InitStruct; + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // Uart TX + GPIO_InitStruct.Pin = UART_TX_PIN ; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = UART_TX_GPIO_AF; + HAL_GPIO_Init(UART_TX_GPIO_PORT, &GPIO_InitStruct); + + // Uart RX + GPIO_InitStruct.Pin = UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = UART_RX_GPIO_AF; + HAL_GPIO_Init(UART_RX_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UARTx; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&UartHandle); + +#if BOARD_DEVICE_RHPORT_NUM == 0 + // Despite being call USB2_OTG + // OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port + // PA9 VUSB, PA10 ID, PA11 DM, PA12 DP + + /* Configure USB FS GPIOs */ + /* Configure DM DP Pins */ + GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure VBUS Pin collides with USART TX*/ +// GPIO_InitStruct.Pin = GPIO_PIN_9; +// GPIO_InitStruct.Mode = GPIO_MODE_INPUT; +// GPIO_InitStruct.Pull = GPIO_NOPULL; +// HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure OTG-FS ID pin */ + GPIO_InitStruct.Pin = GPIO_PIN_10; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Enable USB FS Clocks */ + __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); + + // Enable VBUS sense (B device) via pin PA9 +// USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; +#define DEVICE_BASE (USB_OTG_DeviceTypeDef *) (USB_OTG_FS_PERIPH_BASE + USB_OTG_DEVICE_BASE) + USB_OTG_DeviceTypeDef * dev = DEVICE_BASE; + dev->DCTL |= USB_OTG_DCTL_SDIS; + + /* Deactivate VBUS Sensing B */ + USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + /* B-peripheral session valid override enable */ + USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; +#elif BOARD_DEVICE_RHPORT_NUM == 1 + // Despite being call USB2_OTG + // OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port + __GPIOA_CLK_ENABLE(); + __GPIOB_CLK_ENABLE(); + __GPIOC_CLK_ENABLE(); + __GPIOH_CLK_ENABLE(); + + /* ULPI CK */ + GPIO_InitStruct.Pin = GPIO_PIN_5; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* ULPI D0 */ + GPIO_InitStruct.Pin = GPIO_PIN_3; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* ULPI D1 D2 D3 D4 D5 D6 D7 */ + GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_5; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + /* ULPI STP DIR */ + GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_2; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + + /* NXT */ + GPIO_InitStruct.Pin = GPIO_PIN_4; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOH, &GPIO_InitStruct); + + // Enable ULPI clock + __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE(); + + /* Enable USB HS Clocks */ + __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); + + // No VBUS sense + USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // B-peripheral session valid override enable + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + + // Force device mode + USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; + USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; + +#endif // rhport = 1 +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + return HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32f746disco/stm32f7xx_hal_conf.h b/hw/bsp/stm32f746disco/stm32f7xx_hal_conf.h new file mode 100644 index 000000000..03dec8f0d --- /dev/null +++ b/hw/bsp/stm32f746disco/stm32f7xx_hal_conf.h @@ -0,0 +1,472 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_CONF_H +#define __STM32F7xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/* #define HAL_ADC_MODULE_ENABLED */ +/* #define HAL_CAN_MODULE_ENABLED */ +/* #define HAL_CAN_LEGACY_MODULE_ENABLED */ +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_DCMI_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_HASH_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_LTDC_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SAI_MODULE_ENABLED */ +/* #define HAL_SD_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +/* #define HAL_SPI_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +/* #define HAL_PCD_MODULE_ENABLED */ +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +/* #define HAL_DSI_MODULE_ENABLED */ +/* #define HAL_JPEG_MODULE_ENABLED */ +/* #define HAL_MDIOS_MODULE_ENABLED */ + + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x0FU) /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 1U +#define ART_ACCLERATOR_ENABLE 1U /* To enable instruction cache and prefetch */ + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIOS register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + +/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ +/* LAN8742A PHY Address*/ +#define LAN8742A_PHY_ADDRESS 0x00 +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY ((uint32_t)0x00000FFF) +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) + +#define PHY_READ_TO ((uint32_t)0x0000FFFF) +#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ + +#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */ + +#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */ + + +#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */ +#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 1U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f7xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f7xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f7xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f7xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f7xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f7xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED + #include "stm32f7xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32f7xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f7xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32f7xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32f7xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f7xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32f7xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32f7xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f7xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32f7xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32f7xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32f7xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f7xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f7xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f7xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED + #include "stm32f7xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED + #include "stm32f7xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f7xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32f7xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32f7xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f7xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32f7xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32f7xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32f7xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f7xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f7xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f7xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f7xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f7xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f7xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f7xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f7xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32f7xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32f7xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32f7xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_JPEG_MODULE_ENABLED + #include "stm32f7xx_hal_jpeg.h" +#endif /* HAL_JPEG_MODULE_ENABLED */ + +#ifdef HAL_MDIOS_MODULE_ENABLED + #include "stm32f7xx_hal_mdios.h" +#endif /* HAL_MDIOS_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F7xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/hw/bsp/stm32f769disco/STM32F769ZITx_FLASH.ld b/hw/bsp/stm32f769disco/STM32F769ZITx_FLASH.ld new file mode 100644 index 000000000..378ed80dd --- /dev/null +++ b/hw/bsp/stm32f769disco/STM32F769ZITx_FLASH.ld @@ -0,0 +1,167 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F767ZITx Device with +** 2048KByte FLASH, 512KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20080000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 2048K +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 512K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/stm32f769disco/board.mk b/hw/bsp/stm32f769disco/board.mk new file mode 100644 index 000000000..62c05cca5 --- /dev/null +++ b/hw/bsp/stm32f769disco/board.mk @@ -0,0 +1,51 @@ +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m7 \ + -mfloat-abi=hard \ + -mfpu=fpv5-d16 \ + -nostdlib -nostartfiles \ + -DSTM32F769xx \ + -DHSE_VALUE=25000000 \ + -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ + -DBOARD_DEVICE_RHPORT_NUM=1 \ + -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + +# suppress warning caused by vendor mcu driver +CFLAGS += -Wno-error=cast-align -Wno-error=shadow + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F7xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F7xx + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/STM32F769ZITx_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32f7xx.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_uart.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_pwr_ex.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f769xx.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = synopsys + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM7/r0p1 + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32f769disco/stm32f769disco.c b/hw/bsp/stm32f769disco/stm32f769disco.c new file mode 100644 index 000000000..2664fe0e0 --- /dev/null +++ b/hw/bsp/stm32f769disco/stm32f769disco.c @@ -0,0 +1,297 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020 Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de), + * Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32f7xx_hal.h" + +void OTG_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void OTG_HS_IRQHandler(void) +{ + tud_int_handler(1); +} + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PORT GPIOJ +#define LED_PIN GPIO_PIN_12 +#define LED_STATE_ON 5 + +#define BUTTON_PORT GPIOA +#define BUTTON_PIN GPIO_PIN_0 +#define BUTTON_STATE_ACTIVE 1 + +#define UARTx USART1 +#define UART_GPIO_PORT GPIOA +#define UART_GPIO_AF GPIO_AF7_USART1 +#define UART_TX_PIN GPIO_PIN_9 +#define UART_RX_PIN GPIO_PIN_10 + +UART_HandleTypeDef UartHandle; + +// enable all LED, Button, Uart, USB clock +static void all_rcc_clk_enable(void) +{ + __HAL_RCC_GPIOA_CLK_ENABLE(); // Button, UART, ULPI CLK|D0 + __HAL_RCC_GPIOB_CLK_ENABLE(); // ULPI D1-7 + __HAL_RCC_GPIOC_CLK_ENABLE(); // ULPI STP + __HAL_RCC_GPIOH_CLK_ENABLE(); // ULPI NXT + __HAL_RCC_GPIOI_CLK_ENABLE(); // ULPI NXT + __HAL_RCC_GPIOJ_CLK_ENABLE(); // LED + __HAL_RCC_USART1_CLK_ENABLE(); // Uart module +} + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSE) + * SYSCLK(Hz) = 216000000 + * HCLK(Hz) = 216000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 4 + * APB2 Prescaler = 2 + * HSE Frequency(Hz) = 25000000 + * PLL_M = HSE_VALUE/1000000 + * PLL_N = 432 + * PLL_P = 2 + * PLL_Q = 9 + * PLL_R = 7 + * VDD(V) = 3.3 + * Main regulator output voltage = Scale1 mode + * Flash Latency(WS) = 7 + * The USB clock configuration from PLLSAI: + * PLLSAIP = 8 + * PLLSAIN = 384 + * PLLSAIQ = 7 + * @param None + * @retval None + */ +void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* Enable Power Control clock */ + __HAL_RCC_PWR_CLK_ENABLE(); + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; + RCC_OscInitStruct.PLL.PLLN = 432; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 9; + RCC_OscInitStruct.PLL.PLLR = 7; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Activate the OverDrive to reach the 216 MHz Frequency */ + HAL_PWREx_EnableOverDrive(); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); +} + +void board_init(void) +{ + SystemClock_Config(); + all_rcc_clk_enable(); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#endif + + GPIO_InitTypeDef GPIO_InitStruct; + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UARTx; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&UartHandle); + + /* Configure USB HS GPIOs */ + /* ULPI CLK */ + GPIO_InitStruct.Pin = GPIO_PIN_5; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* D0 */ + GPIO_InitStruct.Pin = GPIO_PIN_3; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* D1 D2 D3 D4 D5 D6 D7 */ + GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13 | GPIO_PIN_5; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + /* STP */ + GPIO_InitStruct.Pin = GPIO_PIN_0; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + + /* NXT */ + GPIO_InitStruct.Pin = GPIO_PIN_4; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOH, &GPIO_InitStruct); + + /* DIR */ + GPIO_InitStruct.Pin = GPIO_PIN_11; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOI, &GPIO_InitStruct); + + // Enable ULPI clock + __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE(); + + /* Enable USB HS Clocks */ + __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); + + // No VBUS sense + USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // B-peripheral session valid override enable + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + + // Force device mode + USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; + USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; + +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + return HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h b/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h new file mode 100644 index 000000000..03dec8f0d --- /dev/null +++ b/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h @@ -0,0 +1,472 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_CONF_H +#define __STM32F7xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/* #define HAL_ADC_MODULE_ENABLED */ +/* #define HAL_CAN_MODULE_ENABLED */ +/* #define HAL_CAN_LEGACY_MODULE_ENABLED */ +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_DCMI_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_HASH_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_LTDC_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SAI_MODULE_ENABLED */ +/* #define HAL_SD_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +/* #define HAL_SPI_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +/* #define HAL_PCD_MODULE_ENABLED */ +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +/* #define HAL_DSI_MODULE_ENABLED */ +/* #define HAL_JPEG_MODULE_ENABLED */ +/* #define HAL_MDIOS_MODULE_ENABLED */ + + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x0FU) /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 1U +#define ART_ACCLERATOR_ENABLE 1U /* To enable instruction cache and prefetch */ + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIOS register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + +/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ +/* LAN8742A PHY Address*/ +#define LAN8742A_PHY_ADDRESS 0x00 +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY ((uint32_t)0x00000FFF) +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) + +#define PHY_READ_TO ((uint32_t)0x0000FFFF) +#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ + +#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */ + +#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */ + + +#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */ +#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 1U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f7xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f7xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f7xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f7xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f7xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f7xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED + #include "stm32f7xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32f7xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f7xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32f7xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32f7xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f7xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32f7xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32f7xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f7xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32f7xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32f7xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32f7xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f7xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f7xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f7xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED + #include "stm32f7xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED + #include "stm32f7xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f7xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32f7xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32f7xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f7xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32f7xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32f7xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32f7xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f7xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f7xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f7xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f7xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f7xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f7xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f7xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f7xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32f7xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32f7xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32f7xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_JPEG_MODULE_ENABLED + #include "stm32f7xx_hal_jpeg.h" +#endif /* HAL_JPEG_MODULE_ENABLED */ + +#ifdef HAL_MDIOS_MODULE_ENABLED + #include "stm32f7xx_hal_mdios.h" +#endif /* HAL_MDIOS_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F7xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit v1.3.1 From 30a18e260562194b0541584600a0cfc88b1ef178 Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Wed, 24 Jun 2020 16:25:23 +0200 Subject: stm32f723disco: USB HS enumerates. --- hw/bsp/stm32f723disco/stm32f723disco.c | 6 ++- src/portable/st/synopsys/dcd_synopsys.c | 87 ++++++++++++++++++++++++++++++--- 2 files changed, 85 insertions(+), 8 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32f723disco/stm32f723disco.c b/hw/bsp/stm32f723disco/stm32f723disco.c index 03057edc7..eeedd2a66 100644 --- a/hw/bsp/stm32f723disco/stm32f723disco.c +++ b/hw/bsp/stm32f723disco/stm32f723disco.c @@ -217,7 +217,7 @@ void board_init(void) GPIO_InitStruct.Pin = (GPIO_PIN_14 | GPIO_PIN_15); GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_VERY_HIGH; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); @@ -231,8 +231,12 @@ void board_init(void) GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; HAL_GPIO_Init(GPIOD, &GPIO_InitStruct); + /* Enable PHYC Clocks */ + __HAL_RCC_OTGPHYC_CLK_ENABLE(); + /* Enable USB HS Clocks */ __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); + __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE(); // Enable VBUS sense (B device) via pin PA9 USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; diff --git a/src/portable/st/synopsys/dcd_synopsys.c b/src/portable/st/synopsys/dcd_synopsys.c index 6e26fd09a..ba3cc3460 100644 --- a/src/portable/st/synopsys/dcd_synopsys.c +++ b/src/portable/st/synopsys/dcd_synopsys.c @@ -27,6 +27,7 @@ */ #include "tusb_option.h" +#include "../../../../hw/bsp//board.h" #if defined (STM32F105x8) || defined (STM32F105xB) || defined (STM32F105xC) || \ defined (STM32F107xB) || defined (STM32F107xC) @@ -147,14 +148,13 @@ typedef struct { typedef volatile uint32_t * usb_fifo_t; #if TUD_OPT_RHPORT == 1 -xfer_ctl_t xfer_status[EP_MAX_HS][2]; # define EP_MAX EP_MAX_HS # define EP_FIFO_SIZE EP_FIFO_SIZE_HS #else -xfer_ctl_t xfer_status[EP_MAX_FS][2]; # define EP_MAX EP_MAX_FS # define EP_FIFO_SIZE EP_FIFO_SIZE_FS #endif +xfer_ctl_t xfer_status[EP_MAX][2]; #define XFER_CTL_BASE(_ep, _dir) &xfer_status[_ep][_dir] // EP0 transfers are limited to 1 packet - larger sizes has to be split @@ -220,9 +220,9 @@ static void bus_reset(uint8_t rhport) // overwrite this. #if TUD_OPT_HIGH_SPEED - _allocated_fifo_words = 271 + 2*EP_MAX_HS; + _allocated_fifo_words = 271 + 2*EP_MAX; #else - _allocated_fifo_words = 47 + 2*EP_MAX_FS; + _allocated_fifo_words = 47 + 2*EP_MAX; #endif usb_otg->GRXFSIZ = _allocated_fifo_words; @@ -301,6 +301,59 @@ static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t c } +# if defined(USB_HS_PHYC) && TUD_OPT_HIGH_SPEED +static bool USB_HS_PHYCInit(void) +{ + USB_HS_PHYC_GlobalTypeDef *usb_hs_phyc = (USB_HS_PHYC_GlobalTypeDef *)USB_HS_PHYC_CONTROLLER_BASE; + // Enable LDO + usb_hs_phyc->USB_HS_PHYC_LDO |= USB_HS_PHYC_LDO_ENABLE; + int32_t count = 2000000; + while(1) { + if (usb_hs_phyc->USB_HS_PHYC_LDO & USB_HS_PHYC_LDO_STATUS) + break; + TU_ASSERT(count > 0); + } + uint32_t phyc_pll = 0; + switch (HSE_VALUE) { + case 12000000: + phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_12MHZ; + break; + case 12500000: + phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_12_5MHZ; + break; + case 16000000: + phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_16MHZ; + break; + case 24000000: + phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_24MHZ; + break; + case 25000000: + phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_25MHZ; + break; + case 32000000: + // Value not defined in header + phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_Msk; + break; + default: + TU_ASSERT(0); + } + usb_hs_phyc->USB_HS_PHYC_PLL = phyc_pll; + + // Use magic value as in stm32f7xx_ll_usb. +# if !defined (USB_HS_PHYC_TUNE_VALUE) +# define USB_HS_PHYC_TUNE_VALUE 0x00000F13U /*!< Value of USB HS PHY Tune */ +# endif /* USB_HS_PHYC_TUNE_VALUE */ + // Control the tuning interface of the High Speed PHY */ + usb_hs_phyc->USB_HS_PHYC_TUNE |= USB_HS_PHYC_TUNE_VALUE; + + // Enable PLL internal PHY + usb_hs_phyc->USB_HS_PHYC_PLL = phyc_pll | USB_HS_PHYC_PLL_PLLEN; + + board_delay(2); + return true; +} +# endif + /*------------------------------------------------------------------*/ /* Controller API *------------------------------------------------------------------*/ @@ -315,12 +368,31 @@ void dcd_init (uint8_t rhport) #if TUD_OPT_HIGH_SPEED // TODO may pass parameter instead of using macro for HighSpeed if ( rhport == 1 ) { - // Highspeed with external ULPI PHY - // deactivate internal PHY usb_otg->GCCFG &= ~USB_OTG_GCCFG_PWRDWN; - // On selected MCUs HS port1 can be used with external PHY via ULPI interface + // TODO may pass parameter instead of using macro for HighSpeed +#if defined(USB_HS_PHYC) + // Highspeed with embedded UTMI PHYC + // Init The UTMI Interface + usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_TSDPS | USB_OTG_GUSBCFG_ULPIFSLS | USB_OTG_GUSBCFG_PHYSEL); + + // Select vbus source + usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_ULPIEVBUSD | USB_OTG_GUSBCFG_ULPIEVBUSI); + + // Select UTMI Interace + usb_otg->GUSBCFG &= ~USB_OTG_GUSBCFG_ULPI_UTMI_SEL; + usb_otg->GCCFG |= USB_OTG_GCCFG_PHYHSEN; + + //Enables control of a High Speed USB PHY + USB_HS_PHYCInit(); + + // Disable external VBUS detection + usb_otg->GUSBCFG &= ~USB_OTG_GUSBCFG_ULPIEVBUSD; + +# else// On selected MCUs HS port1 can be used with external PHY via ULPI interface + // Highspeed with external ULPI PHY + // Init ULPI Interface usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_TSDPS | USB_OTG_GUSBCFG_ULPIFSLS | USB_OTG_GUSBCFG_PHYSEL); @@ -328,6 +400,7 @@ void dcd_init (uint8_t rhport) usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_ULPIEVBUSD | USB_OTG_GUSBCFG_ULPIEVBUSI); set_turnaround(usb_otg, TUSB_SPEED_HIGH); +# endif } else #endif -- cgit v1.3.1 From f3a88477dc39a5eccc8d4de61d8943ace2b74e44 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 30 Jun 2020 16:18:43 +0700 Subject: revert rhport config in nxp mcus --- hw/bsp/ea4357/ea4357.c | 8 ++++---- hw/bsp/mcb1800/mcb1800.c | 8 ++++---- hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c | 4 ++-- hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c | 4 ++-- hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c | 4 ++-- hw/bsp/ngx4330/ngx4330.c | 8 ++++---- hw/bsp/teensy_40/teensy40.c | 4 ++-- 7 files changed, 20 insertions(+), 20 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/ea4357/ea4357.c b/hw/bsp/ea4357/ea4357.c index 04c4e60a6..b7e7f7a5c 100644 --- a/hw/bsp/ea4357/ea4357.c +++ b/hw/bsp/ea4357/ea4357.c @@ -149,7 +149,7 @@ void board_init(void) * status feedback from the distribution switch. GPIO54 is used for VBUS sensing. 15Kohm pull-down * resistors are always active */ -#if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE | OPT_MODE_HOST) +#if CFG_TUSB_RHPORT0_MODE Chip_USB0_Init(); // // Reset controller @@ -185,7 +185,7 @@ void board_init(void) * of VBUS can be read via U31. * JP16 shall not be inserted. */ -#if CFG_TUSB_RHPORT0_MODE & ((OPT_MODE_DEVICE | OPT_MODE_HOST) << 8) +#if CFG_TUSB_RHPORT1_MODE Chip_USB1_Init(); // // Reset controller @@ -232,11 +232,11 @@ void USB0_IRQHandler(void) void USB1_IRQHandler(void) { - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST tuh_isr(1); #endif - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE tud_int_handler(1); #endif } diff --git a/hw/bsp/mcb1800/mcb1800.c b/hw/bsp/mcb1800/mcb1800.c index 6387f983e..ae9f1b62f 100644 --- a/hw/bsp/mcb1800/mcb1800.c +++ b/hw/bsp/mcb1800/mcb1800.c @@ -43,11 +43,11 @@ void USB0_IRQHandler(void) void USB1_IRQHandler(void) { - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST tuh_isr(1); #endif - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE tud_int_handler(1); #endif } @@ -163,7 +163,7 @@ void board_init(void) }; // USB0 -#if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE | OPT_MODE_HOST) +#if CFG_TUSB_RHPORT0_MODE Chip_USB0_Init(); // // Reset controller @@ -180,7 +180,7 @@ void board_init(void) #endif // USB1 -#if CFG_TUSB_RHPORT0_MODE & ((OPT_MODE_DEVICE | OPT_MODE_HOST) << 8) +#if CFG_TUSB_RHPORT1_MODE Chip_USB1_Init(); // // Reset controller diff --git a/hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c b/hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c index 8dae7a0c2..be0ae3ea8 100644 --- a/hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c +++ b/hw/bsp/mimxrt1050_evkb/mimxrt1050_evkb.c @@ -134,11 +134,11 @@ void USB_OTG1_IRQHandler(void) void USB_OTG2_IRQHandler(void) { - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST tuh_isr(1); #endif - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE tud_int_handler(1); #endif } diff --git a/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c b/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c index 8dae7a0c2..0f55c2b00 100644 --- a/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c +++ b/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c @@ -134,11 +134,11 @@ void USB_OTG1_IRQHandler(void) void USB_OTG2_IRQHandler(void) { - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) + #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST tuh_isr(1); #endif - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE tud_int_handler(1); #endif } diff --git a/hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c b/hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c index 8dae7a0c2..be0ae3ea8 100644 --- a/hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c +++ b/hw/bsp/mimxrt1064_evk/mimxrt1064_evk.c @@ -134,11 +134,11 @@ void USB_OTG1_IRQHandler(void) void USB_OTG2_IRQHandler(void) { - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST tuh_isr(1); #endif - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE tud_int_handler(1); #endif } diff --git a/hw/bsp/ngx4330/ngx4330.c b/hw/bsp/ngx4330/ngx4330.c index 85d11d6ad..5296ddcb3 100644 --- a/hw/bsp/ngx4330/ngx4330.c +++ b/hw/bsp/ngx4330/ngx4330.c @@ -161,7 +161,7 @@ void board_init(void) * status feedback from the distribution switch. GPIO54 is used for VBUS sensing. 15Kohm pull-down * resistors are always active */ -#if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE | OPT_MODE_HOST) +#if CFG_TUSB_RHPORT0_MODE Chip_USB0_Init(); // // Reset controller @@ -197,7 +197,7 @@ void board_init(void) * of VBUS can be read via U31. * JP16 shall not be inserted. */ -#if CFG_TUSB_RHPORT0_MODE & ((OPT_MODE_DEVICE | OPT_MODE_HOST) << 8) +#if CFG_TUSB_RHPORT1_MODE Chip_USB1_Init(); // // Reset controller @@ -235,11 +235,11 @@ void USB0_IRQHandler(void) void USB1_IRQHandler(void) { - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST tuh_isr(1); #endif - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE tud_int_handler(1); #endif } diff --git a/hw/bsp/teensy_40/teensy40.c b/hw/bsp/teensy_40/teensy40.c index 0ca86f602..f45a98ef3 100644 --- a/hw/bsp/teensy_40/teensy40.c +++ b/hw/bsp/teensy_40/teensy40.c @@ -135,11 +135,11 @@ void USB_OTG1_IRQHandler(void) void USB_OTG2_IRQHandler(void) { - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_HOST << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST tuh_isr(1); #endif - #if CFG_TUSB_RHPORT0_MODE & (OPT_MODE_DEVICE << 8) + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE tud_int_handler(1); #endif } -- cgit v1.3.1 From 0477446224c1c193f5ae8a0cbed7c33e13e7ce6c Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 30 Jun 2020 16:31:59 +0700 Subject: more clean up --- CONTRIBUTORS.md | 7 +++---- hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c | 2 +- 2 files changed, 4 insertions(+), 5 deletions(-) (limited to 'hw/bsp') diff --git a/CONTRIBUTORS.md b/CONTRIBUTORS.md index ef691c98a..f7d77afe3 100644 --- a/CONTRIBUTORS.md +++ b/CONTRIBUTORS.md @@ -12,6 +12,9 @@ * Author and maintainer * Most features development +* **[Jan Dümpelmann](https://github.com/duempel)** + * Improvements to Synopsys device controller driver (DCD) for STM32 MCUs + * **[Jeff Epler](https://github.com/jepler)** * Improvement to MIDI device driver @@ -57,8 +60,4 @@ * TI MSP430 device driver port * Board support for STM32F407 Discovery, STM32H743 Nucleo, pyboard v1.1, msp_exp430f5529lp etc ... -* **[Jan Dümpelmann](https://github.com/duempel)** - * Improvements to Synopsys device controller driver (DCD) for STM32 MCUs - - **[Full contributors list](https://github.com/hathach/tinyusb/contributors).** diff --git a/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c b/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c index 0f55c2b00..be0ae3ea8 100644 --- a/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c +++ b/hw/bsp/mimxrt1060_evk/mimxrt1060_evk.c @@ -134,7 +134,7 @@ void USB_OTG1_IRQHandler(void) void USB_OTG2_IRQHandler(void) { - #if CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST + #if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST tuh_isr(1); #endif -- cgit v1.3.1 From 2f946e765d99dee846a15830b98a6e422dd683a4 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 1 Jul 2020 12:42:12 +0700 Subject: rename file --- hw/bsp/da1469x_dk_pro/da1469x-dk-pro.c | 127 ++++++++++++++++++++++++++ hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c | 127 -------------------------- 2 files changed, 127 insertions(+), 127 deletions(-) create mode 100644 hw/bsp/da1469x_dk_pro/da1469x-dk-pro.c delete mode 100644 hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c (limited to 'hw/bsp') diff --git a/hw/bsp/da1469x_dk_pro/da1469x-dk-pro.c b/hw/bsp/da1469x_dk_pro/da1469x-dk-pro.c new file mode 100644 index 000000000..85fa17152 --- /dev/null +++ b/hw/bsp/da1469x_dk_pro/da1469x-dk-pro.c @@ -0,0 +1,127 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020 Jerzy Kasenberg + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board.h" +#include +#include + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB_IRQHandler(void) +{ + tud_int_handler(0); +} + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PIN 33 +#define LED_STATE_ON 1 +#define LED_STATE_OFF 0 + +#define BUTTON_PIN 6 + +void UnhandledIRQ(void) +{ + CRG_TOP->SYS_CTRL_REG = 0x80; + __BKPT(1); + while(1); +} + +void board_init(void) +{ + // LED + hal_gpio_init_out(LED_PIN, LED_STATE_ON); + + hal_gpio_init_out(1, 0); + hal_gpio_init_out(2, 0); + hal_gpio_init_out(3, 0); + hal_gpio_init_out(4, 0); + hal_gpio_init_out(5, 0); + + // Button + hal_gpio_init_in(BUTTON_PIN, HAL_GPIO_PULL_NONE); + + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + + NVIC_SetPriority(USB_IRQn, 2); + + /* Setup USB IRQ */ + NVIC_SetPriority(USB_IRQn, 2); + NVIC_EnableIRQ(USB_IRQn); + + /* Use PLL96 / 2 clock not HCLK */ + CRG_TOP->CLK_CTRL_REG &= ~CRG_TOP_CLK_CTRL_REG_USB_CLK_SRC_Msk; + + mcu_gpio_set_pin_function(14, MCU_GPIO_MODE_INPUT, MCU_GPIO_FUNC_USB); + mcu_gpio_set_pin_function(15, MCU_GPIO_MODE_INPUT, MCU_GPIO_FUNC_USB); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + hal_gpio_write(LED_PIN, state ? LED_STATE_ON : LED_STATE_OFF); +} + +uint32_t board_button_read(void) +{ + // button is active LOW + return hal_gpio_read(BUTTON_PIN) ^ 1; +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void)buf; + (void)len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + (void)buf; + (void)len; + + return 0; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif diff --git a/hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c b/hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c deleted file mode 100644 index 85fa17152..000000000 --- a/hw/bsp/da1469x_dk_pro/dialog_da1469x-dk-pro.c +++ /dev/null @@ -1,127 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2020 Jerzy Kasenberg - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "bsp/board.h" -#include -#include - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void USB_IRQHandler(void) -{ - tud_int_handler(0); -} - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ - -#define LED_PIN 33 -#define LED_STATE_ON 1 -#define LED_STATE_OFF 0 - -#define BUTTON_PIN 6 - -void UnhandledIRQ(void) -{ - CRG_TOP->SYS_CTRL_REG = 0x80; - __BKPT(1); - while(1); -} - -void board_init(void) -{ - // LED - hal_gpio_init_out(LED_PIN, LED_STATE_ON); - - hal_gpio_init_out(1, 0); - hal_gpio_init_out(2, 0); - hal_gpio_init_out(3, 0); - hal_gpio_init_out(4, 0); - hal_gpio_init_out(5, 0); - - // Button - hal_gpio_init_in(BUTTON_PIN, HAL_GPIO_PULL_NONE); - - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); - - NVIC_SetPriority(USB_IRQn, 2); - - /* Setup USB IRQ */ - NVIC_SetPriority(USB_IRQn, 2); - NVIC_EnableIRQ(USB_IRQn); - - /* Use PLL96 / 2 clock not HCLK */ - CRG_TOP->CLK_CTRL_REG &= ~CRG_TOP_CLK_CTRL_REG_USB_CLK_SRC_Msk; - - mcu_gpio_set_pin_function(14, MCU_GPIO_MODE_INPUT, MCU_GPIO_FUNC_USB); - mcu_gpio_set_pin_function(15, MCU_GPIO_MODE_INPUT, MCU_GPIO_FUNC_USB); -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - hal_gpio_write(LED_PIN, state ? LED_STATE_ON : LED_STATE_OFF); -} - -uint32_t board_button_read(void) -{ - // button is active LOW - return hal_gpio_read(BUTTON_PIN) ^ 1; -} - -int board_uart_read(uint8_t* buf, int len) -{ - (void)buf; - (void)len; - return 0; -} - -int board_uart_write(void const * buf, int len) -{ - (void)buf; - (void)len; - - return 0; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif -- cgit v1.3.1 From 463e978134c7ee1d4abae4937f9c0c3e603ac6bc Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 1 Jul 2020 12:47:14 +0700 Subject: added DA14695 DK USB bsp --- README.md | 1 + docs/boards.md | 5 + hw/bsp/da14695_dk_usb/board.mk | 59 ++++++ hw/bsp/da14695_dk_usb/da14695_dk_usb.c | 127 ++++++++++++ hw/bsp/da14695_dk_usb/da1469x.ld | 245 ++++++++++++++++++++++ hw/bsp/da14695_dk_usb/gcc_startup_da1469x.S | 301 ++++++++++++++++++++++++++++ hw/bsp/da14695_dk_usb/product_header.dump | Bin 0 -> 8192 bytes hw/bsp/da14695_dk_usb/syscfg/syscfg.h | 34 ++++ hw/bsp/da1469x_dk_pro/board.mk | 7 +- 9 files changed, 773 insertions(+), 6 deletions(-) create mode 100644 hw/bsp/da14695_dk_usb/board.mk create mode 100644 hw/bsp/da14695_dk_usb/da14695_dk_usb.c create mode 100644 hw/bsp/da14695_dk_usb/da1469x.ld create mode 100644 hw/bsp/da14695_dk_usb/gcc_startup_da1469x.S create mode 100644 hw/bsp/da14695_dk_usb/product_header.dump create mode 100644 hw/bsp/da14695_dk_usb/syscfg/syscfg.h (limited to 'hw/bsp') diff --git a/README.md b/README.md index 31e40b399..f9a7d0b73 100644 --- a/README.md +++ b/README.md @@ -31,6 +31,7 @@ Special thanks to all the people who spent their precious time and effort to hel The stack supports the following MCUs: - **Espressif:** ESP32-S2 +- **Dialog:** DA1469x - **MicroChip:** SAMD21, SAMD51, SAME5x (device only) - **NordicSemi:** nRF52833, nRF52840 - **Nuvoton:** NUC120, NUC121/NUC125, NUC126, NUC505 diff --git a/docs/boards.md b/docs/boards.md index 46d071853..57b1410bc 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -14,6 +14,11 @@ This code base already had supported for a handful of following boards (sorted a - [ESP32-S2-Kaluga-1](https://docs.espressif.com/projects/esp-idf/en/latest/esp32s2/hw-reference/esp32s2/user-guide-esp32-s2-kaluga-1-kit.html) - [ESP32-S2-Saola-1](https://docs.espressif.com/projects/esp-idf/en/latest/esp32s2/hw-reference/esp32s2/user-guide-saola-1-v1.2.html) +### Dialog DA146xx + +- [DA14695 Development Kit – USB](https://www.dialog-semiconductor.com/products/da14695-development-kit-usb) +- [DA1469x Development Kit – Pro](https://www.dialog-semiconductor.com/products/da14695-development-kit-pro) + ### MicroChip SAMD - [Adafruit Circuit Playground Express](https://www.adafruit.com/product/3333) diff --git a/hw/bsp/da14695_dk_usb/board.mk b/hw/bsp/da14695_dk_usb/board.mk new file mode 100644 index 000000000..f5b8873f9 --- /dev/null +++ b/hw/bsp/da14695_dk_usb/board.mk @@ -0,0 +1,59 @@ + CFLAGS += \ + -flto \ + -mthumb \ + -mthumb-interwork \ + -mabi=aapcs \ + -mcpu=cortex-m33+nodsp \ + -mfloat-abi=hard \ + -mfpu=fpv5-sp-d16 \ + -nostdlib \ + -DCORE_M33 \ + -DCFG_TUSB_MCU=OPT_MCU_DA1469X \ + -DCFG_TUD_ENDPOINT0_SIZE=8\ + +MCU_FAMILY_DIR = hw/mcu/dialog/da1469x + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/da1469x.ld + +SRC_C += \ + $(MCU_FAMILY_DIR)/src/system_da1469x.c \ + $(MCU_FAMILY_DIR)/src/da1469x_clock.c \ + $(MCU_FAMILY_DIR)/src/hal_gpio.c \ + +SRC_S += $(TOP)/hw/bsp/$(BOARD)/gcc_startup_da1469x.S + +INC += \ + $(TOP)/hw/bsp/$(BOARD) \ + $(TOP)/$(MCU_FAMILY_DIR)/include \ + $(TOP)/$(MCU_FAMILY_DIR)/SDK_10.0.8.105/sdk/bsp/include \ + +# For TinyUSB port source +VENDOR = dialog +# While this is for da1469x chip, there is chance that da1468x chip family will also work +CHIP_FAMILY = da146xx + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM33_NTZ/non_secure + +# For flash-jlink target +JLINK_DEVICE = DA14695 +JLINK_IF = swd + +# flash using jlink but with some twists +flash: flash-dialog + +flash-dialog: $(BUILD)/$(BOARD)-firmware.bin + @echo '#define SW_VERSION "v_1.0.0.1"' >$(BUILD)/version.h + @echo '#define SW_VERSION_DATE "'`date +"%Y-%m-%d %H:%M"`'"' >>$(BUILD)/version.h + mkimage da1469x $(BUILD)/$(BOARD)-firmware.bin $(BUILD)/version.h $^.img + cp $(TOP)/hw/bsp/$(BOARD)/product_header.dump $(BUILD)/$(BOARD)-image.bin + cat $^.img >> $(BUILD)/$(BOARD)-image.bin + @echo r > $(BUILD)/$(BOARD).jlink + @echo halt >> $(BUILD)/$(BOARD).jlink + @echo loadfile $(BUILD)/$(BOARD)-image.bin 0x16000000 >> $(BUILD)/$(BOARD).jlink + @echo r >> $(BUILD)/$(BOARD).jlink + @echo go >> $(BUILD)/$(BOARD).jlink + @echo exit >> $(BUILD)/$(BOARD).jlink + $(JLINKEXE) -device $(JLINK_DEVICE) -if $(JLINK_IF) -JTAGConf -1,-1 -speed auto -CommandFile $(BUILD)/$(BOARD).jlink + diff --git a/hw/bsp/da14695_dk_usb/da14695_dk_usb.c b/hw/bsp/da14695_dk_usb/da14695_dk_usb.c new file mode 100644 index 000000000..e7c7ae364 --- /dev/null +++ b/hw/bsp/da14695_dk_usb/da14695_dk_usb.c @@ -0,0 +1,127 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020 Jerzy Kasenberg + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board.h" +#include +#include + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB_IRQHandler(void) +{ + tud_int_handler(0); +} + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PIN 33 // P1.1 +#define LED_STATE_ON 1 +#define LED_STATE_OFF (1-LED_STATE_ON) + +#define BUTTON_PIN 6 + +void UnhandledIRQ(void) +{ + CRG_TOP->SYS_CTRL_REG = 0x80; + __BKPT(1); + while(1); +} + +void board_init(void) +{ + // LED + hal_gpio_init_out(LED_PIN, LED_STATE_ON); + + hal_gpio_init_out(1, 0); + hal_gpio_init_out(2, 0); + hal_gpio_init_out(3, 0); + hal_gpio_init_out(4, 0); + hal_gpio_init_out(5, 0); + + // Button + hal_gpio_init_in(BUTTON_PIN, HAL_GPIO_PULL_NONE); + + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + + NVIC_SetPriority(USB_IRQn, 2); + + /* Setup USB IRQ */ + NVIC_SetPriority(USB_IRQn, 2); + NVIC_EnableIRQ(USB_IRQn); + + /* Use PLL96 / 2 clock not HCLK */ + CRG_TOP->CLK_CTRL_REG &= ~CRG_TOP_CLK_CTRL_REG_USB_CLK_SRC_Msk; + + mcu_gpio_set_pin_function(14, MCU_GPIO_MODE_INPUT, MCU_GPIO_FUNC_USB); + mcu_gpio_set_pin_function(15, MCU_GPIO_MODE_INPUT, MCU_GPIO_FUNC_USB); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + hal_gpio_write(LED_PIN, state ? LED_STATE_ON : LED_STATE_OFF); +} + +uint32_t board_button_read(void) +{ + // button is active LOW + return hal_gpio_read(BUTTON_PIN) ^ 1; +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void)buf; + (void)len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + (void)buf; + (void)len; + + return 0; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif diff --git a/hw/bsp/da14695_dk_usb/da1469x.ld b/hw/bsp/da14695_dk_usb/da1469x.ld new file mode 100644 index 000000000..96507d6e7 --- /dev/null +++ b/hw/bsp/da14695_dk_usb/da1469x.ld @@ -0,0 +1,245 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + +MEMORY +{ + /* + * Flash is remapped at 0x0 by 1st stage bootloader, but this is done with + * an offset derived from image header thus it is safer to use remapped + * address space at 0x0 instead of QSPI_M address space at 0x16000000. + * Bootloader partition is 32K, but 9K is currently reserved for product + * header (8K) and image header (1K). + * First 512 bytes of SYSRAM are remapped at 0x0 and used as ISR vector + * (there's no need to reallocate ISR vector) and thus cannot be used by + * application. + */ + + FLASH (r) : ORIGIN = (0x00000000), LENGTH = (1024 * 1024) + RAM (rw) : ORIGIN = (0x20000000), LENGTH = (512 * 1024) +} + +OUTPUT_FORMAT ("elf32-littlearm", "elf32-bigarm", "elf32-littlearm") + +/* Linker script to place sections and symbol values. Should be used together + * with other linker script that defines memory regions FLASH and RAM. + * It references following symbols, which must be defined in code: + * Reset_Handler : Entry of reset handler + * + * It defines following symbols, which code can use without definition: + * __exidx_start + * __exidx_end + * __etext + * __data_start__ + * __preinit_array_start + * __preinit_array_end + * __init_array_start + * __init_array_end + * __fini_array_start + * __fini_array_end + * __data_end__ + * __bss_start__ + * __bss_end__ + * __HeapBase + * __HeapLimit + * __StackLimit + * __StackTop + * __stack + * __bssnz_start__ + * __bssnz_end__ + */ +ENTRY(Reset_Handler) + +SECTIONS +{ + __text = .; + + .text : + { + __isr_vector_start = .; + KEEP(*(.isr_vector)) + /* ISR vector shall have exactly 512 bytes */ + . = __isr_vector_start + 0x200; + __isr_vector_end = .; + + *(.text) + *(.text.*) + + *(.libcmac.rom) + + KEEP(*(.init)) + KEEP(*(.fini)) + + /* .ctors */ + *crtbegin.o(.ctors) + *crtbegin?.o(.ctors) + *(EXCLUDE_FILE(*crtend?.o *crtend.o) .ctors) + *(SORT(.ctors.*)) + *(.ctors) + + /* .dtors */ + *crtbegin.o(.dtors) + *crtbegin?.o(.dtors) + *(EXCLUDE_FILE(*crtend?.o *crtend.o) .dtors) + *(SORT(.dtors.*)) + *(.dtors) + + *(.rodata*) + + *(.eh_frame*) + . = ALIGN(4); + } > FLASH + + .ARM.extab : + { + *(.ARM.extab* .gnu.linkonce.armextab.*) + . = ALIGN(4); + } > FLASH + + __exidx_start = .; + .ARM : + { + *(.ARM.exidx* .gnu.linkonce.armexidx.*) + . = ALIGN(4); + } > FLASH + __exidx_end = .; + + .intvect : + { + . = ALIGN(4); + __intvect_start__ = .; + . = . + (__isr_vector_end - __isr_vector_start); + . = ALIGN(4); + } > RAM + + .sleep_state (NOLOAD) : + { + . = ALIGN(4); + *(sleep_state) + } > RAM + + /* This section will be zeroed by RTT package init */ + .rtt (NOLOAD): + { + . = ALIGN(4); + *(.rtt) + . = ALIGN(4); + } > RAM + + __text_ram_addr = LOADADDR(.text_ram); + + .text_ram : + { + . = ALIGN(4); + __text_ram_start__ = .; + *(.text_ram*) + . = ALIGN(4); + __text_ram_end__ = .; + } > RAM AT > FLASH + + __etext = LOADADDR(.data); + + .data : + { + __data_start__ = .; + *(vtable) + *(.data*) + + . = ALIGN(4); + /* preinit data */ + PROVIDE_HIDDEN (__preinit_array_start = .); + *(.preinit_array) + PROVIDE_HIDDEN (__preinit_array_end = .); + + . = ALIGN(4); + /* init data */ + PROVIDE_HIDDEN (__init_array_start = .); + *(SORT(.init_array.*)) + *(.init_array) + PROVIDE_HIDDEN (__init_array_end = .); + + + . = ALIGN(4); + /* finit data */ + PROVIDE_HIDDEN (__fini_array_start = .); + *(SORT(.fini_array.*)) + *(.fini_array) + PROVIDE_HIDDEN (__fini_array_end = .); + + *(.jcr) + . = ALIGN(4); + /* All data end */ + __data_end__ = .; + } > RAM AT > FLASH + + .bssnz : + { + . = ALIGN(4); + __bssnz_start__ = .; + *(.bss.core.nz*) + . = ALIGN(4); + __bssnz_end__ = .; + } > RAM + + .bss : + { + . = ALIGN(4); + __bss_start__ = .; + *(.bss*) + *(COMMON) + . = ALIGN(4); + __bss_end__ = .; + } > RAM + + .cmac (NOLOAD) : + { + . = ALIGN(0x400); + *(.libcmac.ram) + } > RAM + + /* Heap starts after BSS */ + . = ALIGN(8); + __HeapBase = .; + + /* .stack_dummy section doesn't contains any symbols. It is only + * used for linker to calculate size of stack sections, and assign + * values to stack symbols later */ + .stack_dummy (COPY): + { + *(.stack*) + } > RAM + + _ram_start = ORIGIN(RAM); + + /* Set stack top to end of RAM, and stack limit move down by + * size of stack_dummy section */ + __StackTop = ORIGIN(RAM) + LENGTH(RAM); + __StackLimit = __StackTop - SIZEOF(.stack_dummy); + PROVIDE(__stack = __StackTop); + + /* Top of head is the bottom of the stack */ + __HeapLimit = __StackLimit; + end = __HeapLimit; + + /* Check if data + heap + stack exceeds RAM limit */ + ASSERT(__HeapBase <= __HeapLimit, "region RAM overflowed with stack") + + /* Check that intvect is at the beginning of RAM */ + ASSERT(__intvect_start__ == ORIGIN(RAM), "intvect is not at beginning of RAM") +} + diff --git a/hw/bsp/da14695_dk_usb/gcc_startup_da1469x.S b/hw/bsp/da14695_dk_usb/gcc_startup_da1469x.S new file mode 100644 index 000000000..d47fbcd97 --- /dev/null +++ b/hw/bsp/da14695_dk_usb/gcc_startup_da1469x.S @@ -0,0 +1,301 @@ +/* + * Licensed to the Apache Software Foundation (ASF) under one + * or more contributor license agreements. See the NOTICE file + * distributed with this work for additional information + * regarding copyright ownership. The ASF licenses this file + * to you under the Apache License, Version 2.0 (the + * "License"); you may not use this file except in compliance + * with the License. You may obtain a copy of the License at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, + * software distributed under the License is distributed on an + * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY + * KIND, either express or implied. See the License for the + * specific language governing permissions and limitations + * under the License. + */ + + #include "syscfg/syscfg.h" + + .syntax unified + .arch armv7-m + + .section .stack + .align 3 +#ifdef __STACK_SIZE + .equ Stack_Size, __STACK_SIZE +#else + .equ Stack_Size, 0xC00 +#endif + .equ SYS_CTRL_REG, 0x50000024 + .equ CACHE_FLASH_REG, 0x100C0040 + .equ RESET_STAT_REG, 0x500000BC + + .globl __StackTop + .globl __StackLimit +__StackLimit: + .space Stack_Size + .size __StackLimit, . - __StackLimit +__StackTop: + .size __StackTop, . - __StackTop + + .section .heap + .align 3 +#ifdef __HEAP_SIZE + .equ Heap_Size, __HEAP_SIZE +#else + .equ Heap_Size, 0 +#endif + .globl __HeapBase + .globl __HeapLimit +__HeapBase: + .if Heap_Size + .space Heap_Size + .endif + .size __HeapBase, . - __HeapBase +__HeapLimit: + .size __HeapLimit, . - __HeapLimit + + .section .isr_vector + .align 2 + .globl __isr_vector +__isr_vector: + .long __StackTop + .long Reset_Handler + /* Cortex-M33 interrupts */ + .long NMI_Handler + .long HardFault_Handler + .long MemoryManagement_Handler + .long BusFault_Handler + .long UsageFault_Handler + .long SecureFault_Handler + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long SVC_Handler + .long DebugMonitor_Handler + .long 0 /* Reserved */ + .long PendSV_Handler + .long SysTick_Handler + /* DA1469x interrupts */ + .long SENSOR_NODE_IRQHandler + .long DMA_IRQHandler + .long CHARGER_STATE_IRQHandler + .long CHARGER_ERROR_IRQHandler + .long CMAC2SYS_IRQHandler + .long UART_IRQHandler + .long UART2_IRQHandler + .long UART3_IRQHandler + .long I2C_IRQHandler + .long I2C2_IRQHandler + .long SPI_IRQHandler + .long SPI2_IRQHandler + .long PCM_IRQHandler + .long SRC_IN_IRQHandler + .long SRC_OUT_IRQHandler + .long USB_IRQHandler + .long TIMER_IRQHandler + .long TIMER2_IRQHandler + .long RTC_IRQHandler + .long KEY_WKUP_GPIO_IRQHandler + .long PDC_IRQHandler + .long VBUS_IRQHandler + .long MRM_IRQHandler + .long MOTOR_CONTROLLER_IRQHandler + .long TRNG_IRQHandler + .long DCDC_IRQHandler + .long XTAL32M_RDY_IRQHandler + .long ADC_IRQHandler + .long ADC2_IRQHandler + .long CRYPTO_IRQHandler + .long CAPTIMER1_IRQHandler + .long RFDIAG_IRQHandler + .long LCD_CONTROLLER_IRQHandler + .long PLL_LOCK_IRQHandler + .long TIMER3_IRQHandler + .long TIMER4_IRQHandler + .long LRA_IRQHandler + .long RTC_EVENT_IRQHandler + .long GPIO_P0_IRQHandler + .long GPIO_P1_IRQHandler + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .long 0 /* Reserved */ + .size __isr_vector, . - __isr_vector + + .text + .thumb + .thumb_func + .align 2 + .globl Reset_Handler + .type Reset_Handler, %function +Reset_Handler: + /* Make sure interrupt vector is remapped at 0x0 */ + ldr r1, =SYS_CTRL_REG + ldrh r2, [r1, #0] + orrs r2, r2, #8 + strh r2, [r1, #0] + +#if !MYNEWT_VAL(RAM_RESIDENT) +/* + * Flash is remapped at 0x0 with an offset, i.e. 0x0 does not correspond to + * 0x16000000 but to start of an image on flash. This is calculated from product + * header by 1st state bootloader and configured in CACHE_FLASH_REG. We need to + * retrieve proper offset value for calculations later. + */ + ldr r1, =CACHE_FLASH_REG + ldr r4, [r1, #0] + mov r2, r4 + mov r3, #0xFFFF + bic r4, r4, r3 /* CACHE_FLASH_REG[FLASH_REGION_BASE] */ + mov r3, #0xFFF0 + and r2, r2, r3 /* CACHE_FLASH_REG[FLASH_REGION_OFFSET] */ + lsr r2, r2, #2 + orr r4, r4, r2 + +/* Copy ISR vector from flash to RAM */ + ldr r1, =__isr_vector_start /* src ptr */ + ldr r2, =__isr_vector_end /* src end */ + ldr r3, =__intvect_start__ /* dst ptr */ +/* Make sure we copy from QSPIC address range, not from remapped range */ + cmp r1, r4 + itt lt + addlt r1, r1, r4 + addlt r2, r2, r4 +.loop_isr_copy: + cmp r1, r2 + ittt lt + ldrlt r0, [r1], #4 + strlt r0, [r3], #4 + blt .loop_isr_copy + +/* Copy QSPI code from flash to RAM */ + ldr r1, =__text_ram_addr /* src ptr */ + ldr r2, =__text_ram_start__ /* ptr */ + ldr r3, =__text_ram_end__ /* dst end */ +.loop_code_text_ram_copy: + cmp r2, r3 + ittt lt + ldrlt r0, [r1], #4 + strlt r0, [r2], #4 + blt .loop_code_text_ram_copy + +/* Copy data from flash to RAM */ + ldr r1, =__etext /* src ptr */ + ldr r2, =__data_start__ /* dst ptr */ + ldr r3, =__data_end__ /* dst end */ +.loop_data_copy: + cmp r2, r3 + ittt lt + ldrlt r0, [r1], #4 + strlt r0, [r2], #4 + blt .loop_data_copy +#endif + +/* Clear BSS */ + movs r0, 0 + ldr r1, =__bss_start__ + ldr r2, =__bss_end__ +.loop_bss_clear: + cmp r1, r2 + itt lt + strlt r0, [r1], #4 + blt .loop_bss_clear + + ldr r0, =__HeapBase + ldr r1, =__HeapLimit +/* Call static constructors */ + bl __libc_init_array + + bl SystemInit + bl main + + .pool + .size Reset_Handler, . - Reset_Handler + +/* Default interrupt handler */ + .type Default_Handler, %function +Default_Handler: + ldr r1, =SYS_CTRL_REG + ldrh r2, [r1, #0] + orrs r2, r2, #0x80 /* DEBUGGER_ENABLE */ + strh r2, [r1, #0] + b . + + .size Default_Handler, . - Default_Handler + +/* Default handlers for all interrupts */ + .macro IRQ handler + .weak \handler + .set \handler, Default_Handler + .endm + + /* Cortex-M33 interrupts */ + IRQ NMI_Handler + IRQ HardFault_Handler + IRQ MemoryManagement_Handler + IRQ BusFault_Handler + IRQ UsageFault_Handler + IRQ SecureFault_Handler + IRQ SVC_Handler + IRQ DebugMonitor_Handler + IRQ PendSV_Handler + IRQ SysTick_Handler + /* DA1469x interrupts */ + IRQ SENSOR_NODE_IRQHandler + IRQ DMA_IRQHandler + IRQ CHARGER_STATE_IRQHandler + IRQ CHARGER_ERROR_IRQHandler + IRQ CMAC2SYS_IRQHandler + IRQ UART_IRQHandler + IRQ UART2_IRQHandler + IRQ UART3_IRQHandler + IRQ I2C_IRQHandler + IRQ I2C2_IRQHandler + IRQ SPI_IRQHandler + IRQ SPI2_IRQHandler + IRQ PCM_IRQHandler + IRQ SRC_IN_IRQHandler + IRQ SRC_OUT_IRQHandler + IRQ USB_IRQHandler + IRQ TIMER_IRQHandler + IRQ TIMER2_IRQHandler + IRQ RTC_IRQHandler + IRQ KEY_WKUP_GPIO_IRQHandler + IRQ PDC_IRQHandler + IRQ VBUS_IRQHandler + IRQ MRM_IRQHandler + IRQ MOTOR_CONTROLLER_IRQHandler + IRQ TRNG_IRQHandler + IRQ DCDC_IRQHandler + IRQ XTAL32M_RDY_IRQHandler + IRQ ADC_IRQHandler + IRQ ADC2_IRQHandler + IRQ CRYPTO_IRQHandler + IRQ CAPTIMER1_IRQHandler + IRQ RFDIAG_IRQHandler + IRQ LCD_CONTROLLER_IRQHandler + IRQ PLL_LOCK_IRQHandler + IRQ TIMER3_IRQHandler + IRQ TIMER4_IRQHandler + IRQ LRA_IRQHandler + IRQ RTC_EVENT_IRQHandler + IRQ GPIO_P0_IRQHandler + IRQ GPIO_P1_IRQHandler + IRQ RESERVED40_IRQHandler + IRQ RESERVED41_IRQHandler + IRQ RESERVED42_IRQHandler + IRQ RESERVED43_IRQHandler + IRQ RESERVED44_IRQHandler + IRQ RESERVED45_IRQHandler + IRQ RESERVED46_IRQHandler + IRQ RESERVED47_IRQHandler + +.end diff --git a/hw/bsp/da14695_dk_usb/product_header.dump b/hw/bsp/da14695_dk_usb/product_header.dump new file mode 100644 index 000000000..ea4842242 Binary files /dev/null and b/hw/bsp/da14695_dk_usb/product_header.dump differ diff --git a/hw/bsp/da14695_dk_usb/syscfg/syscfg.h b/hw/bsp/da14695_dk_usb/syscfg/syscfg.h new file mode 100644 index 000000000..6cbb4319e --- /dev/null +++ b/hw/bsp/da14695_dk_usb/syscfg/syscfg.h @@ -0,0 +1,34 @@ +/** + * This file was generated by Apache newt version: 1.9.0-dev + */ + +#ifndef H_MYNEWT_SYSCFG_ +#define H_MYNEWT_SYSCFG_ + +/** + * This macro exists to ensure code includes this header when needed. If code + * checks the existence of a setting directly via ifdef without including this + * header, the setting macro will silently evaluate to 0. In contrast, an + * attempt to use these macros without including this header will result in a + * compiler error. + */ +#define MYNEWT_VAL(_name) MYNEWT_VAL_ ## _name +#define MYNEWT_VAL_CHOICE(_name, _val) MYNEWT_VAL_ ## _name ## __ ## _val + +#ifndef MYNEWT_VAL_RAM_RESIDENT +#define MYNEWT_VAL_RAM_RESIDENT (0) +#endif + +#ifndef MYNEWT_VAL_MCU_GPIO_MAX_IRQ +#define MYNEWT_VAL_MCU_GPIO_MAX_IRQ (4) +#endif + +#ifndef MYNEWT_VAL_MCU_GPIO_RETAINABLE_NUM +#define MYNEWT_VAL_MCU_GPIO_RETAINABLE_NUM (-1) +#endif + +#ifndef MYNEWT_VAL_MCU_CLOCK_XTAL32M_SETTLE_TIME_US +#define MYNEWT_VAL_MCU_CLOCK_XTAL32M_SETTLE_TIME_US (2000) +#endif + +#endif diff --git a/hw/bsp/da1469x_dk_pro/board.mk b/hw/bsp/da1469x_dk_pro/board.mk index c8a268aa5..6708955f2 100644 --- a/hw/bsp/da1469x_dk_pro/board.mk +++ b/hw/bsp/da1469x_dk_pro/board.mk @@ -11,11 +11,7 @@ -DCFG_TUSB_MCU=OPT_MCU_DA1469X \ -DCFG_TUD_ENDPOINT0_SIZE=8\ -# mcu driver cause following warnings -# CFLAGS += -Wno-error=strict-prototypes -Wno-error=unused-parameter - MCU_FAMILY_DIR = hw/mcu/dialog/da1469x -MCU_DIR = hw/mcu/dialog/da14699 # All source paths should be relative to the top level. LD_FILE = hw/bsp/$(BOARD)/da1469x.ld @@ -28,8 +24,7 @@ SRC_C += \ SRC_S += $(TOP)/hw/bsp/$(BOARD)/gcc_startup_da1469x.S INC += \ - $(TOP)/hw/bsp/$(BOARD) \ - $(TOP)/$(MCU_DIR)/include \ + $(TOP)/hw/bsp/$(BOARD) \ $(TOP)/$(MCU_FAMILY_DIR)/include \ $(TOP)/$(MCU_FAMILY_DIR)/SDK_10.0.8.105/sdk/bsp/include \ -- cgit v1.3.1 From 77315ba7ce65291b7f77b6258c4546c7dfde0246 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 1 Jul 2020 18:27:48 +0700 Subject: added uart for h743 --- hw/bsp/stm32h743eval/stm32h743eval.c | 22 ++++++++++------------ 1 file changed, 10 insertions(+), 12 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h743eval/stm32h743eval.c b/hw/bsp/stm32h743eval/stm32h743eval.c index 772edf33c..6a51d8884 100644 --- a/hw/bsp/stm32h743eval/stm32h743eval.c +++ b/hw/bsp/stm32h743eval/stm32h743eval.c @@ -61,6 +61,7 @@ void OTG_HS_IRQHandler(void) #define BUTTON_PIN GPIO_PIN_13 #define BUTTON_STATE_ACTIVE 0 +// Need to change jumper setting J7 and J8 from RS-232 to STLink #define UARTx USART1 #define UART_GPIO_PORT GPIOB #define UART_GPIO_AF GPIO_AF4_USART1 @@ -74,8 +75,8 @@ static void all_rcc_clk_enable(void) { __HAL_RCC_GPIOA_CLK_ENABLE(); // LED __HAL_RCC_GPIOC_CLK_ENABLE(); // Button -// __HAL_RCC_GPIOB_CLK_ENABLE(); // Uart tx, rx -// __HAL_RCC_USART1_CLK_ENABLE(); // Uart module + __HAL_RCC_GPIOB_CLK_ENABLE(); // Uart tx, rx + __HAL_RCC_USART1_CLK_ENABLE(); // Uart module } /* PWR, RCC, GPIO (All): AHB4 (D3 domain) @@ -197,20 +198,19 @@ void board_init(void) GPIO_InitTypeDef GPIO_InitStruct; // LED - GPIO_InitStruct.Pin = LED_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); // Button - GPIO_InitStruct.Pin = BUTTON_PIN; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); -#if 0 // Uart GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; @@ -228,7 +228,6 @@ void board_init(void) UartHandle.Init.Mode = UART_MODE_TX_RX; UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; HAL_UART_Init(&UartHandle); -#endif #if BOARD_DEVICE_RHPORT_NUM == 0 // Despite being call USB2_OTG @@ -365,8 +364,7 @@ int board_uart_read(uint8_t* buf, int len) int board_uart_write(void const * buf, int len) { - (void) buf; (void) len; -// HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); return len; } -- cgit v1.3.1 From 5b3a67a1e208296d927da31c3df1aefa562ec2ac Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Wed, 1 Jul 2020 14:52:49 +0200 Subject: Add bsp for stlinkv3mini. --- hw/bsp/stlinkv3mini/STM32F723xE_FLASH.ld | 167 +++++++++++ hw/bsp/stlinkv3mini/board.mk | 59 ++++ hw/bsp/stlinkv3mini/stlinkv3mini.c | 298 +++++++++++++++++++ hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h | 472 +++++++++++++++++++++++++++++++ 4 files changed, 996 insertions(+) create mode 100644 hw/bsp/stlinkv3mini/STM32F723xE_FLASH.ld create mode 100644 hw/bsp/stlinkv3mini/board.mk create mode 100644 hw/bsp/stlinkv3mini/stlinkv3mini.c create mode 100644 hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h (limited to 'hw/bsp') diff --git a/hw/bsp/stlinkv3mini/STM32F723xE_FLASH.ld b/hw/bsp/stlinkv3mini/STM32F723xE_FLASH.ld new file mode 100644 index 000000000..8645ce5c5 --- /dev/null +++ b/hw/bsp/stlinkv3mini/STM32F723xE_FLASH.ld @@ -0,0 +1,167 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F723xE Device with +** 512KByte FLASH, 256KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20040000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x460; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 256K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 512K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/stlinkv3mini/board.mk b/hw/bsp/stlinkv3mini/board.mk new file mode 100644 index 000000000..8576eeaa8 --- /dev/null +++ b/hw/bsp/stlinkv3mini/board.mk @@ -0,0 +1,59 @@ +PORT ?= 1 + +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m7 \ + -mfloat-abi=hard \ + -mfpu=fpv5-d16 \ + -nostdlib -nostartfiles \ + -DSTM32F723xx \ + -DHSE_VALUE=25000000 \ + -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ + -DBOARD_DEVICE_RHPORT_NUM=$(PORT) + +ifeq ($(PORT), 1) +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED +$(info "PORT1 HS") +else +$(info "PORT0") +endif + +# mcu driver cause following warnings +CFLAGS += -Wno-error=shadow -Wno-error=cast-align + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32F7xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32F7xx + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/STM32F723xE_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32f7xx.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_uart.c \ + $(ST_HAL_DRIVER)/Src/stm32f7xx_hal_pwr_ex.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32f723xx.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = synopsys + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM7/r0p1 + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stlinkv3mini/stlinkv3mini.c b/hw/bsp/stlinkv3mini/stlinkv3mini.c new file mode 100644 index 000000000..03babcfa9 --- /dev/null +++ b/hw/bsp/stlinkv3mini/stlinkv3mini.c @@ -0,0 +1,298 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020 Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de), + * Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32f7xx_hal.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void OTG_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +// Despite being call USB2_OTG +// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port +void OTG_HS_IRQHandler(void) +{ + tud_int_handler(1); +} + +// Pin configuartion with help from +// RadioOperator/CMSIS-DAP_for_STLINK-V3MINI.git +// CMSIS-DAP_for_STLINK-V3MINI/STLINK-V3MINI/Sch/STLINK-V3MINI_GPIOs.JPG + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PORT GPIOA +#define LED_PIN GPIO_PIN_10 +#define LED_STATE_ON 1 + +/* No Buttom */ + +#define UARTx USART6 +#define UART_GPIO_PORT GPIOG +#define UART_GPIO_AF GPIO_AF8_USART6 +#define UART_TX_PIN GPIO_PIN_9 +#define UART_RX_PIN GPIO_PIN_14 + +UART_HandleTypeDef UartHandle; + +// enable all LED, Button, Uart, USB clock +static void all_rcc_clk_enable(void) +{ + __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D-, LED + __HAL_RCC_GPIOB_CLK_ENABLE(); // OTG_HS + __HAL_RCC_GPIOD_CLK_ENABLE(); // OTG_HS ID + __HAL_RCC_GPIOG_CLK_ENABLE(); // Uart TX, RX + __HAL_RCC_USART6_CLK_ENABLE(); // Uart module +} + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSE) + * SYSCLK(Hz) = 216000000 + * HCLK(Hz) = 216000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 4 + * APB2 Prescaler = 2 + * HSE Frequency(Hz) = 25000000 + * PLL_M = HSE_VALUE/1000000 + * PLL_N = 432 + * PLL_P = 2 + * PLL_Q = 9 + * VDD(V) = 3.3 + * Main regulator output voltage = Scale1 mode + * Flash Latency(WS) = 7 + * The USB clock configuration from PLLSAI: + * PLLSAIP = 8 + * PLLSAIN = 384 + * PLLSAIQ = 7 + * @param None + * @retval None + */ +void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + + /* Enable Power Control clock */ + __HAL_RCC_PWR_CLK_ENABLE(); + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE/1000000; + RCC_OscInitStruct.PLL.PLLN = 432; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 9; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Activate the OverDrive to reach the 216 MHz Frequency */ + HAL_PWREx_EnableOverDrive(); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7); +} + +void board_init(void) +{ + + + SystemClock_Config(); + all_rcc_clk_enable(); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#endif + + GPIO_InitTypeDef GPIO_InitStruct; + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UARTx; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&UartHandle); + +#if BOARD_DEVICE_RHPORT_NUM == 0 + /* Configure USB FS GPIOs */ + /* Configure DM DP Pins */ + GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure VBUS Pin */ + GPIO_InitStruct.Pin = GPIO_PIN_9; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure OTG-FS ID pin */ + GPIO_InitStruct.Pin = GPIO_PIN_10; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Enable USB FS Clocks */ + __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); + + // Enable VBUS sense (B device) via pin PA9 + USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; + +#else + /* Configure USB HS GPIOs */ + /* Configure DM DP Pins */ + GPIO_InitStruct.Pin = (GPIO_PIN_14 | GPIO_PIN_15); + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + // Enable HS VBUS sense (B device) via pin PB13 + USB_OTG_HS->GCCFG |= USB_OTG_GCCFG_VBDEN; + + /* Configure OTG-HS ID pin */ + GPIO_InitStruct.Pin = GPIO_PIN_13; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_HS; + HAL_GPIO_Init(GPIOD, &GPIO_InitStruct); + + /* Enable PHYC Clocks */ + __HAL_RCC_OTGPHYC_CLK_ENABLE(); + + /* Enable USB HS Clocks */ + __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); + __HAL_RCC_USB_OTG_HS_ULPI_CLK_ENABLE(); + + // Enable VBUS sense (B device) via pin PA9 + USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // B-peripheral session valid override enable + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + + // Force device mode + USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; + USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; + +#endif +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + return 0; +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h b/hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h new file mode 100644 index 000000000..03dec8f0d --- /dev/null +++ b/hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h @@ -0,0 +1,472 @@ +/** + ****************************************************************************** + * @file stm32f7xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2016 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F7xx_HAL_CONF_H +#define __STM32F7xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/* #define HAL_ADC_MODULE_ENABLED */ +/* #define HAL_CAN_MODULE_ENABLED */ +/* #define HAL_CAN_LEGACY_MODULE_ENABLED */ +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_DCMI_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_HASH_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_LTDC_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SAI_MODULE_ENABLED */ +/* #define HAL_SD_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +/* #define HAL_SPI_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +/* #define HAL_PCD_MODULE_ENABLED */ +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +/* #define HAL_DSI_MODULE_ENABLED */ +/* #define HAL_JPEG_MODULE_ENABLED */ +/* #define HAL_MDIOS_MODULE_ENABLED */ + + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x0FU) /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 1U +#define ART_ACCLERATOR_ENABLE 1U /* To enable instruction cache and prefetch */ + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIOS register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + +/* ################## Ethernet peripheral configuration for NUCLEO 144 board ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)5) /* 5 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)5) /* 5 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ +/* LAN8742A PHY Address*/ +#define LAN8742A_PHY_ADDRESS 0x00 +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY ((uint32_t)0x00000FFF) +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) + +#define PHY_READ_TO ((uint32_t)0x0000FFFF) +#define PHY_WRITE_TO ((uint32_t)0x0000FFFF) + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ + +#define PHY_SR ((uint16_t)0x1F) /*!< PHY special control/ status register Offset */ + +#define PHY_SPEED_STATUS ((uint16_t)0x0004) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0010) /*!< PHY Duplex mask */ + + +#define PHY_ISFR ((uint16_t)0x1D) /*!< PHY Interrupt Source Flag register Offset */ +#define PHY_ISFR_INT4 ((uint16_t)0x0010) /*!< PHY Link down inturrupt */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 1U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f7xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f7xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f7xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f7xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f7xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f7xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED + #include "stm32f7xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32f7xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f7xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32f7xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32f7xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f7xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32f7xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32f7xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f7xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32f7xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32f7xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32f7xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32f7xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f7xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f7xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f7xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED + #include "stm32f7xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED + #include "stm32f7xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f7xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32f7xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32f7xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f7xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32f7xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32f7xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32f7xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f7xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f7xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f7xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f7xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f7xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f7xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f7xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f7xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32f7xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32f7xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32f7xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_JPEG_MODULE_ENABLED + #include "stm32f7xx_hal_jpeg.h" +#endif /* HAL_JPEG_MODULE_ENABLED */ + +#ifdef HAL_MDIOS_MODULE_ENABLED + #include "stm32f7xx_hal_mdios.h" +#endif /* HAL_MDIOS_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t* file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F7xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit v1.3.1 From 9a290febcdd7aaa50657f3d31da31bd493fa3a0e Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 2 Jul 2020 11:58:40 +0700 Subject: change default port some stm bsp - f769disco default port is highspeed port1 - remove PORT0 on stlink since the board only populated HS connector --- hw/bsp/stlinkv3mini/board.mk | 12 ++----- hw/bsp/stm32f723disco/board.mk | 9 ++--- hw/bsp/stm32h743eval/board.mk | 13 ++++++-- src/portable/st/synopsys/dcd_synopsys.c | 58 ++++++++++++++++++--------------- 4 files changed, 49 insertions(+), 43 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stlinkv3mini/board.mk b/hw/bsp/stlinkv3mini/board.mk index 8576eeaa8..1a64c3735 100644 --- a/hw/bsp/stlinkv3mini/board.mk +++ b/hw/bsp/stlinkv3mini/board.mk @@ -1,5 +1,3 @@ -PORT ?= 1 - CFLAGS += \ -flto \ -mthumb \ @@ -11,14 +9,8 @@ CFLAGS += \ -DSTM32F723xx \ -DHSE_VALUE=25000000 \ -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ - -DBOARD_DEVICE_RHPORT_NUM=$(PORT) - -ifeq ($(PORT), 1) -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED -$(info "PORT1 HS") -else -$(info "PORT0") -endif + -DBOARD_DEVICE_RHPORT_NUM=1 \ + -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED # mcu driver cause following warnings CFLAGS += -Wno-error=shadow -Wno-error=cast-align diff --git a/hw/bsp/stm32f723disco/board.mk b/hw/bsp/stm32f723disco/board.mk index 2bd3b0756..2cf3ac633 100644 --- a/hw/bsp/stm32f723disco/board.mk +++ b/hw/bsp/stm32f723disco/board.mk @@ -1,4 +1,5 @@ -PORT ?= 0 +# Default is Highspeed port +PORT ?= 1 CFLAGS += \ -flto \ @@ -14,10 +15,10 @@ CFLAGS += \ -DBOARD_DEVICE_RHPORT_NUM=$(PORT) ifeq ($(PORT), 1) -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED -$(info "PORT1 HS") + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + $(info "PORT1 High Speed") else -$(info "PORT0") + $(info "PORT0 Full Speed") endif # mcu driver cause following warnings diff --git a/hw/bsp/stm32h743eval/board.mk b/hw/bsp/stm32h743eval/board.mk index cbf37a95d..47d592c58 100644 --- a/hw/bsp/stm32h743eval/board.mk +++ b/hw/bsp/stm32h743eval/board.mk @@ -1,3 +1,6 @@ +# Default is Highspeed port +PORT ?= 1 + CFLAGS += \ -flto \ -mthumb \ @@ -8,8 +11,14 @@ CFLAGS += \ -nostdlib -nostartfiles \ -DSTM32H743xx \ -DCFG_TUSB_MCU=OPT_MCU_STM32H7 \ - -DBOARD_DEVICE_RHPORT_NUM=1 \ - -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + -DBOARD_DEVICE_RHPORT_NUM=$(PORT) + +ifeq ($(PORT), 1) + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + $(info "PORT1 High Speed") +else + $(info "PORT0 Full Speed") +endif # suppress warning caused by vendor mcu driver CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align diff --git a/src/portable/st/synopsys/dcd_synopsys.c b/src/portable/st/synopsys/dcd_synopsys.c index 03238f8e2..a2d1983c2 100644 --- a/src/portable/st/synopsys/dcd_synopsys.c +++ b/src/portable/st/synopsys/dcd_synopsys.c @@ -390,7 +390,7 @@ void dcd_init (uint8_t rhport) // Select default internal VBUS Indicator and Drive for ULPI usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_ULPIEVBUSD | USB_OTG_GUSBCFG_ULPIEVBUSI); -#if defined(USB_HS_PHYC) + #if defined(USB_HS_PHYC) // Highspeed with embedded UTMI PHYC // Select UTMI Interface @@ -399,8 +399,9 @@ void dcd_init (uint8_t rhport) // Enables control of a High Speed USB PHY USB_HS_PHYCInit(); -#endif - } else + #endif + } + else #endif { // Enable internal PHY @@ -770,43 +771,46 @@ static void handle_rxflvl_ints(uint8_t rhport, USB_OTG_OUTEndpointTypeDef * out_ switch(pktsts) { case 0x01: // Global OUT NAK (Interrupt) - break; + break; + case 0x02: // Out packet recvd - { - xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, TUSB_DIR_OUT); + { + xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, TUSB_DIR_OUT); - // Read packet off RxFIFO - read_fifo_packet(rhport, xfer->buffer, bcnt); + // Read packet off RxFIFO + read_fifo_packet(rhport, xfer->buffer, bcnt); - // Increment pointer to xfer data - xfer->buffer += bcnt; + // Increment pointer to xfer data + xfer->buffer += bcnt; - // Truncate transfer length in case of short packet - if(bcnt < xfer->max_size) { - xfer->total_len -= (out_ep[epnum].DOEPTSIZ & USB_OTG_DOEPTSIZ_XFRSIZ_Msk) >> USB_OTG_DOEPTSIZ_XFRSIZ_Pos; - if(epnum == 0) { - xfer->total_len -= ep0_pending[TUSB_DIR_OUT]; - ep0_pending[TUSB_DIR_OUT] = 0; - } + // Truncate transfer length in case of short packet + if(bcnt < xfer->max_size) { + xfer->total_len -= (out_ep[epnum].DOEPTSIZ & USB_OTG_DOEPTSIZ_XFRSIZ_Msk) >> USB_OTG_DOEPTSIZ_XFRSIZ_Pos; + if(epnum == 0) { + xfer->total_len -= ep0_pending[TUSB_DIR_OUT]; + ep0_pending[TUSB_DIR_OUT] = 0; } } - break; + } + break; + case 0x03: // Out packet done (Interrupt) break; + case 0x04: // Setup packet done (Interrupt) out_ep[epnum].DOEPTSIZ |= (3 << USB_OTG_DOEPTSIZ_STUPCNT_Pos); - break; + break; + case 0x06: // Setup packet recvd - { - // We can receive up to three setup packets in succession, but - // only the last one is valid. - _setup_packet[0] = (* rx_fifo); - _setup_packet[1] = (* rx_fifo); - } - break; + // We can receive up to three setup packets in succession, but + // only the last one is valid. + _setup_packet[0] = (* rx_fifo); + _setup_packet[1] = (* rx_fifo); + break; + default: // Invalid TU_BREAKPOINT(); - break; + break; } } -- cgit v1.3.1 From 4cec866994f32f729844d0159e14c178f5aa904f Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 2 Jul 2020 14:57:00 +0700 Subject: correct HSE_VALUE in hal_conf - although it is define in CFLAGS, it is worth to correct to be consistent with other build - extract set_speed() --- README.md | 2 +- docs/boards.md | 5 ++ hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h | 2 +- hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h | 2 +- hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h | 2 +- src/portable/st/synopsys/dcd_synopsys.c | 106 ++++++++++++++++------------- 6 files changed, 66 insertions(+), 53 deletions(-) (limited to 'hw/bsp') diff --git a/README.md b/README.md index f9a7d0b73..8246ff460 100644 --- a/README.md +++ b/README.md @@ -39,7 +39,7 @@ The stack supports the following MCUs: - LPC Series: 11Uxx, 13xx, 175x_6x, 177x_8x, 18xx, 40xx, 43xx, 51Uxx, 54xxx, 55xx - iMX RT Series: RT1011, RT1015, RT1021, RT1052, RT1062, RT1064 - **Sony:** CXD56 -- **ST:** STM32 series: L0, F0, F1, F2, F3, F4, F7, H7 (device only) +- **ST:** STM32 series: L0, F0, F1, F2, F3, F4, F7, H7 both FullSpeed and HighSpeed - **TI:** MSP430 - **[ValentyUSB](https://github.com/im-tomu/valentyusb)** eptri diff --git a/docs/boards.md b/docs/boards.md index 57b1410bc..d3dcec375 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -85,6 +85,7 @@ This code base already had supported for a handful of following boards (sorted a - [Adafruit Feather STM32F405](https://www.adafruit.com/product/4382) - [Micro Python PyBoard v1.1](https://store.micropython.org/product/PYBv1.1) +- [STLink-V3 Mini](https://www.st.com/en/development-tools/stlink-v3mini.html) - [STM32 L035c8 Discovery](https://www.st.com/en/evaluation-tools/32l0538discovery.html) - [STM32 F070rb Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f070rb.html) - [STM32 F072rb Discovery](https://www.st.com/en/evaluation-tools/32f072bdiscovery.html) @@ -96,9 +97,13 @@ This code base already had supported for a handful of following boards (sorted a - STM32 F411ce Black Pill - [STM32 F411ve Discovery](https://www.st.com/en/evaluation-tools/32f411ediscovery.html) - [STM32 F412zg Discovery](https://www.st.com/en/evaluation-tools/32f412gdiscovery.html) +- [STM32 F723e Discovery](https://www.st.com/en/evaluation-tools/32f723ediscovery.html) - [STM32 F746zg Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f746zg.html) +- [STM32 F746g Discovery](https://www.st.com/en/evaluation-tools/32f746gdiscovery.html) - [STM32 F767zi Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f767zi.html) +- [STM32 F769i Discovery](https://www.st.com/en/evaluation-tools/32f769idiscovery.html) - [STM32 H743zi Nucleo](https://www.st.com/en/evaluation-tools/nucleo-h743zi.html) +- [STM32 H743i Evaluation](https://www.st.com/en/evaluation-tools/stm32h743i-eval.html) ### TI diff --git a/hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h b/hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h index 03dec8f0d..581f0e46a 100644 --- a/hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h +++ b/hw/bsp/stlinkv3mini/stm32f7xx_hal_conf.h @@ -87,7 +87,7 @@ * (when HSE is used as system clock source, directly or through the PLL). */ #if !defined (HSE_VALUE) - #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ + #define HSE_VALUE ((uint32_t)25000000U) /*!< Value of the External oscillator in Hz */ #endif /* HSE_VALUE */ #if !defined (HSE_STARTUP_TIMEOUT) diff --git a/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h b/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h index 03dec8f0d..581f0e46a 100644 --- a/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h +++ b/hw/bsp/stm32f723disco/stm32f7xx_hal_conf.h @@ -87,7 +87,7 @@ * (when HSE is used as system clock source, directly or through the PLL). */ #if !defined (HSE_VALUE) - #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ + #define HSE_VALUE ((uint32_t)25000000U) /*!< Value of the External oscillator in Hz */ #endif /* HSE_VALUE */ #if !defined (HSE_STARTUP_TIMEOUT) diff --git a/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h b/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h index 03dec8f0d..581f0e46a 100644 --- a/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h +++ b/hw/bsp/stm32f769disco/stm32f7xx_hal_conf.h @@ -87,7 +87,7 @@ * (when HSE is used as system clock source, directly or through the PLL). */ #if !defined (HSE_VALUE) - #define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */ + #define HSE_VALUE ((uint32_t)25000000U) /*!< Value of the External oscillator in Hz */ #endif /* HSE_VALUE */ #if !defined (HSE_STARTUP_TIMEOUT) diff --git a/src/portable/st/synopsys/dcd_synopsys.c b/src/portable/st/synopsys/dcd_synopsys.c index a2d1983c2..50984c830 100644 --- a/src/portable/st/synopsys/dcd_synopsys.c +++ b/src/portable/st/synopsys/dcd_synopsys.c @@ -285,47 +285,33 @@ static void set_turnaround(USB_OTG_GlobalTypeDef * usb_otg, tusb_speed_t speed) } } -static tusb_speed_t get_speed(USB_OTG_DeviceTypeDef* dev) +static tusb_speed_t get_speed(uint8_t rhport) { + USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); uint32_t const enum_spd = (dev->DSTS & USB_OTG_DSTS_ENUMSPD_Msk) >> USB_OTG_DSTS_ENUMSPD_Pos; return (enum_spd == DCD_HIGH_SPEED) ? TUSB_SPEED_HIGH : TUSB_SPEED_FULL; } -static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t const dir, uint16_t const num_packets, uint16_t total_bytes) { - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - USB_OTG_OUTEndpointTypeDef * out_ep = OUT_EP_BASE(rhport); - USB_OTG_INEndpointTypeDef * in_ep = IN_EP_BASE(rhport); +static void set_speed(uint8_t rhport, tusb_speed_t speed) +{ + uint32_t bitvalue; - // EP0 is limited to one packet each xfer - // We use multiple transaction of xfer->max_size length to get a whole transfer done - if(epnum == 0) { - xfer_ctl_t * const xfer = XFER_CTL_BASE(epnum, dir); - total_bytes = tu_min16(ep0_pending[dir], xfer->max_size); - ep0_pending[dir] -= total_bytes; + if ( rhport == 1 ) + { + bitvalue = ((TUSB_SPEED_HIGH == speed) ? DCD_HIGH_SPEED : DCD_FULL_SPEED_USE_HS); + } + else + { + bitvalue = DCD_FULL_SPEED; } - // IN and OUT endpoint xfers are interrupt-driven, we just schedule them here. - if(dir == TUSB_DIR_IN) { - // A full IN transfer (multiple packets, possibly) triggers XFRC. - in_ep[epnum].DIEPTSIZ = (num_packets << USB_OTG_DIEPTSIZ_PKTCNT_Pos) | - ((total_bytes << USB_OTG_DIEPTSIZ_XFRSIZ_Pos) & USB_OTG_DIEPTSIZ_XFRSIZ_Msk); - - in_ep[epnum].DIEPCTL |= USB_OTG_DIEPCTL_EPENA | USB_OTG_DIEPCTL_CNAK; - // Enable fifo empty interrupt only if there are something to put in the fifo. - if(total_bytes != 0) { - dev->DIEPEMPMSK |= (1 << epnum); - } - } else { - // A full OUT transfer (multiple packets, possibly) triggers XFRC. - out_ep[epnum].DOEPTSIZ &= ~(USB_OTG_DOEPTSIZ_PKTCNT_Msk | USB_OTG_DOEPTSIZ_XFRSIZ); - out_ep[epnum].DOEPTSIZ |= (num_packets << USB_OTG_DOEPTSIZ_PKTCNT_Pos) | - ((total_bytes << USB_OTG_DOEPTSIZ_XFRSIZ_Pos) & USB_OTG_DOEPTSIZ_XFRSIZ_Msk); + USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - out_ep[epnum].DOEPCTL |= USB_OTG_DOEPCTL_EPENA | USB_OTG_DOEPCTL_CNAK; - } + // Clear and set speed bits + dev->DCFG &= ~(3 << USB_OTG_DCFG_DSPD_Pos); + dev->DCFG |= (bitvalue << USB_OTG_DCFG_DSPD_Pos); } - #if defined(USB_HS_PHYC) && TUD_OPT_HIGH_SPEED static bool USB_HS_PHYCInit(void) { @@ -338,6 +324,8 @@ static bool USB_HS_PHYCInit(void) while ( 0 == (usb_hs_phyc->USB_HS_PHYC_LDO & USB_HS_PHYC_LDO_STATUS) ) {} uint32_t phyc_pll = 0; + + // TODO Try to get HSE_VALUE from registers instead of depending CFLAGS switch ( HSE_VALUE ) { case 12000000: phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_12MHZ ; break; @@ -365,6 +353,40 @@ static bool USB_HS_PHYCInit(void) } #endif +static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t const dir, uint16_t const num_packets, uint16_t total_bytes) { + USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); + USB_OTG_OUTEndpointTypeDef * out_ep = OUT_EP_BASE(rhport); + USB_OTG_INEndpointTypeDef * in_ep = IN_EP_BASE(rhport); + + // EP0 is limited to one packet each xfer + // We use multiple transaction of xfer->max_size length to get a whole transfer done + if(epnum == 0) { + xfer_ctl_t * const xfer = XFER_CTL_BASE(epnum, dir); + total_bytes = tu_min16(ep0_pending[dir], xfer->max_size); + ep0_pending[dir] -= total_bytes; + } + + // IN and OUT endpoint xfers are interrupt-driven, we just schedule them here. + if(dir == TUSB_DIR_IN) { + // A full IN transfer (multiple packets, possibly) triggers XFRC. + in_ep[epnum].DIEPTSIZ = (num_packets << USB_OTG_DIEPTSIZ_PKTCNT_Pos) | + ((total_bytes << USB_OTG_DIEPTSIZ_XFRSIZ_Pos) & USB_OTG_DIEPTSIZ_XFRSIZ_Msk); + + in_ep[epnum].DIEPCTL |= USB_OTG_DIEPCTL_EPENA | USB_OTG_DIEPCTL_CNAK; + // Enable fifo empty interrupt only if there are something to put in the fifo. + if(total_bytes != 0) { + dev->DIEPEMPMSK |= (1 << epnum); + } + } else { + // A full OUT transfer (multiple packets, possibly) triggers XFRC. + out_ep[epnum].DOEPTSIZ &= ~(USB_OTG_DOEPTSIZ_PKTCNT_Msk | USB_OTG_DOEPTSIZ_XFRSIZ); + out_ep[epnum].DOEPTSIZ |= (num_packets << USB_OTG_DOEPTSIZ_PKTCNT_Pos) | + ((total_bytes << USB_OTG_DOEPTSIZ_XFRSIZ_Pos) & USB_OTG_DOEPTSIZ_XFRSIZ_Msk); + + out_ep[epnum].DOEPCTL |= USB_OTG_DOEPCTL_EPENA | USB_OTG_DOEPCTL_CNAK; + } +} + /*------------------------------------------------------------------*/ /* Controller API *------------------------------------------------------------------*/ @@ -431,21 +453,10 @@ void dcd_init (uint8_t rhport) // (non zero-length packet), send STALL back and discard. dev->DCFG |= USB_OTG_DCFG_NZLSOHSK; - // Clear speed bits - dev->DCFG &= ~(3 << USB_OTG_DCFG_DSPD_Pos); - - if ( rhport == 1 ) - { - dev->DCFG |= ((TUD_OPT_HIGH_SPEED ? DCD_HIGH_SPEED : DCD_FULL_SPEED_USE_HS) << USB_OTG_DCFG_DSPD_Pos); - } - else - { - // full speed = 0x03 - dev->DCFG |= (DCD_FULL_SPEED << USB_OTG_DCFG_DSPD_Pos); + set_speed(rhport, TUD_OPT_HIGH_SPEED ? TUSB_SPEED_HIGH : TUSB_SPEED_FULL); - // Enable internal USB transceiver. - usb_otg->GCCFG |= USB_OTG_GCCFG_PWRDWN; - } + // Enable internal USB transceiver. + if ( rhport == 0 ) usb_otg->GCCFG |= USB_OTG_GCCFG_PWRDWN; usb_otg->GINTMSK |= USB_OTG_GINTMSK_USBRST | USB_OTG_GINTMSK_ENUMDNEM | USB_OTG_GINTMSK_USBSUSPM | USB_OTG_GINTMSK_WUIM | @@ -511,7 +522,7 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) TU_ASSERT(epnum < EP_MAX); // TODO ISO endpoint can be up to 1024 bytes - TU_ASSERT(desc_edpt->wMaxPacketSize.size <= (get_speed(dev) == TUSB_SPEED_HIGH ? 512 : 64)); + TU_ASSERT(desc_edpt->wMaxPacketSize.size <= (get_speed(rhport) == TUSB_SPEED_HIGH ? 512 : 64)); xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, dir); xfer->max_size = desc_edpt->wMaxPacketSize.size; @@ -575,9 +586,6 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) _allocated_fifo_words += fifo_size; - //TU_LOG2_INT(fifo_size); - //TU_LOG2_INT(_allocated_fifo_words); - in_ep[epnum].DIEPCTL |= (1 << USB_OTG_DIEPCTL_USBAEP_Pos) | (epnum << USB_OTG_DIEPCTL_TXFNUM_Pos) | (desc_edpt->bmAttributes.xfer << USB_OTG_DIEPCTL_EPTYP_Pos) | @@ -925,7 +933,7 @@ void dcd_int_handler(uint8_t rhport) usb_otg->GINTSTS = USB_OTG_GINTSTS_ENUMDNE; - tusb_speed_t const speed = get_speed(dev); + tusb_speed_t const speed = get_speed(rhport); set_turnaround(usb_otg, speed); dcd_event_bus_reset(rhport, speed, true); -- cgit v1.3.1 From fd3817818921981aa67e1fb845f926c010444fea Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Wed, 1 Jul 2020 23:07:18 +0200 Subject: STM32/OTG_HS: Allow OTG_HS port to run at FS speed. Add "REDUCE_SPEED=1" to the compile options. --- hw/bsp/stlinkv3mini/board.mk | 18 ++++++++++++++++-- hw/bsp/stm32f723disco/board.mk | 13 +++++++++---- hw/bsp/stm32f746disco/board.mk | 10 ++++++++-- hw/bsp/stm32f769disco/board.mk | 11 ++++++++++- hw/mcu/nordic/nrfx | 2 +- src/portable/st/synopsys/dcd_synopsys.c | 8 +++----- 6 files changed, 47 insertions(+), 15 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stlinkv3mini/board.mk b/hw/bsp/stlinkv3mini/board.mk index 1a64c3735..47148ec4d 100644 --- a/hw/bsp/stlinkv3mini/board.mk +++ b/hw/bsp/stlinkv3mini/board.mk @@ -1,3 +1,6 @@ +PORT ?= 1 +REDUCE_SPEED ?= 0 + CFLAGS += \ -flto \ -mthumb \ @@ -9,8 +12,19 @@ CFLAGS += \ -DSTM32F723xx \ -DHSE_VALUE=25000000 \ -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ - -DBOARD_DEVICE_RHPORT_NUM=1 \ - -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + -DBOARD_DEVICE_RHPORT_NUM=$(PORT) + +ifeq ($(PORT), 1) + ifeq ($(REDUCE_SPEED), 0) +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED +$(info "Using OTG_HS in HS mode") + else +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED +$(info "Using OTG_HS in FS mode") + endif +else +$(info "Using OTG_FS") +endif # mcu driver cause following warnings CFLAGS += -Wno-error=shadow -Wno-error=cast-align diff --git a/hw/bsp/stm32f723disco/board.mk b/hw/bsp/stm32f723disco/board.mk index 2cf3ac633..47148ec4d 100644 --- a/hw/bsp/stm32f723disco/board.mk +++ b/hw/bsp/stm32f723disco/board.mk @@ -1,5 +1,5 @@ -# Default is Highspeed port PORT ?= 1 +REDUCE_SPEED ?= 0 CFLAGS += \ -flto \ @@ -15,10 +15,15 @@ CFLAGS += \ -DBOARD_DEVICE_RHPORT_NUM=$(PORT) ifeq ($(PORT), 1) - CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED - $(info "PORT1 High Speed") + ifeq ($(REDUCE_SPEED), 0) +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED +$(info "Using OTG_HS in HS mode") + else +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED +$(info "Using OTG_HS in FS mode") + endif else - $(info "PORT0 Full Speed") +$(info "Using OTG_FS") endif # mcu driver cause following warnings diff --git a/hw/bsp/stm32f746disco/board.mk b/hw/bsp/stm32f746disco/board.mk index 76a54cdfd..d7329a28f 100644 --- a/hw/bsp/stm32f746disco/board.mk +++ b/hw/bsp/stm32f746disco/board.mk @@ -1,4 +1,5 @@ PORT ?= 0 +REDUCE_SPEED ?= 0 CFLAGS += \ -flto \ @@ -14,10 +15,15 @@ CFLAGS += \ -DBOARD_DEVICE_RHPORT_NUM=$(PORT) ifeq ($(PORT), 1) + ifeq ($(REDUCE_SPEED), 0) CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED -$(info "PORT1 HS") +$(info "Using OTG_HS in HS mode") + else +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED +$(info "Using OTG_HS in FS mode") + endif else -$(info "PORT0") +$(info "Using OTG_FS") endif # mcu driver cause following warnings diff --git a/hw/bsp/stm32f769disco/board.mk b/hw/bsp/stm32f769disco/board.mk index 62c05cca5..43b677ddd 100644 --- a/hw/bsp/stm32f769disco/board.mk +++ b/hw/bsp/stm32f769disco/board.mk @@ -1,3 +1,5 @@ +REDUCE_SPEED ?= 0 + CFLAGS += \ -flto \ -mthumb \ @@ -10,7 +12,14 @@ CFLAGS += \ -DHSE_VALUE=25000000 \ -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ -DBOARD_DEVICE_RHPORT_NUM=1 \ - -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + +ifeq ($(REDUCE_SPEED), 0) +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED +$(info "Using OTG_HS in HS mode") +else +CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED +$(info "Using OTG_HS in FS mode") +endif # suppress warning caused by vendor mcu driver CFLAGS += -Wno-error=cast-align -Wno-error=shadow diff --git a/hw/mcu/nordic/nrfx b/hw/mcu/nordic/nrfx index a5397bea5..281cc2e17 160000 --- a/hw/mcu/nordic/nrfx +++ b/hw/mcu/nordic/nrfx @@ -1 +1 @@ -Subproject commit a5397bea558fb4b6838081a22d1ee679289d7417 +Subproject commit 281cc2e178fd9a470d844b3afdea9eb322a0b0e8 diff --git a/src/portable/st/synopsys/dcd_synopsys.c b/src/portable/st/synopsys/dcd_synopsys.c index 50984c830..6c3a10b00 100644 --- a/src/portable/st/synopsys/dcd_synopsys.c +++ b/src/portable/st/synopsys/dcd_synopsys.c @@ -312,7 +312,8 @@ static void set_speed(uint8_t rhport, tusb_speed_t speed) dev->DCFG |= (bitvalue << USB_OTG_DCFG_DSPD_Pos); } -#if defined(USB_HS_PHYC) && TUD_OPT_HIGH_SPEED + +#if defined(USB_HS_PHYC) static bool USB_HS_PHYCInit(void) { USB_HS_PHYC_GlobalTypeDef *usb_hs_phyc = (USB_HS_PHYC_GlobalTypeDef*) USB_HS_PHYC_CONTROLLER_BASE; @@ -398,7 +399,6 @@ void dcd_init (uint8_t rhport) USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); // No HNP/SRP (no OTG support), program timeout later. -#if TUD_OPT_HIGH_SPEED // TODO may pass parameter instead of using macro for HighSpeed if ( rhport == 1 ) { // On selected MCUs HS port1 can be used with external PHY via ULPI interface @@ -421,10 +421,8 @@ void dcd_init (uint8_t rhport) // Enables control of a High Speed USB PHY USB_HS_PHYCInit(); - #endif - } - else #endif + } else { // Enable internal PHY usb_otg->GUSBCFG |= USB_OTG_GUSBCFG_PHYSEL; -- cgit v1.3.1 From 4b7539bd6320cc6659fe458e91a51ffb7896f45c Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Thu, 2 Jul 2020 00:23:38 +0200 Subject: stm32h745disco: Only OTG_FS is available. Does not enumerate on replug yet. --- hw/bsp/stm32h745disco/STM32H74xXIHx_FLASH.ld | 173 ++++++++++ hw/bsp/stm32h745disco/board.mk | 58 ++++ hw/bsp/stm32h745disco/stm32h745disco.c | 399 ++++++++++++++++++++++ hw/bsp/stm32h745disco/stm32h7xx_hal_conf.h | 482 +++++++++++++++++++++++++++ 4 files changed, 1112 insertions(+) create mode 100644 hw/bsp/stm32h745disco/STM32H74xXIHx_FLASH.ld create mode 100644 hw/bsp/stm32h745disco/board.mk create mode 100644 hw/bsp/stm32h745disco/stm32h745disco.c create mode 100644 hw/bsp/stm32h745disco/stm32h7xx_hal_conf.h (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h745disco/STM32H74xXIHx_FLASH.ld b/hw/bsp/stm32h745disco/STM32H74xXIHx_FLASH.ld new file mode 100644 index 000000000..59b9ff4df --- /dev/null +++ b/hw/bsp/stm32h745disco/STM32H74xXIHx_FLASH.ld @@ -0,0 +1,173 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32H743XIHx Device with +** 2048KByte FLASH, 128KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20020000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +DTCMRAM (xrw) : ORIGIN = 0x20000000, LENGTH = 128K +RAM_D1 (xrw) : ORIGIN = 0x24000000, LENGTH = 512K +RAM_D2 (xrw) : ORIGIN = 0x30000000, LENGTH = 288K +RAM_D3 (xrw) : ORIGIN = 0x38000000, LENGTH = 64K +ITCMRAM (xrw) : ORIGIN = 0x00000000, LENGTH = 64K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 2048K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >DTCMRAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >DTCMRAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >DTCMRAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} + + diff --git a/hw/bsp/stm32h745disco/board.mk b/hw/bsp/stm32h745disco/board.mk new file mode 100644 index 000000000..b3477b1e6 --- /dev/null +++ b/hw/bsp/stm32h745disco/board.mk @@ -0,0 +1,58 @@ +# STM32H745I-DISCO uses OTG_FS +# FIXME: Reset enumerates, un/replug USB plug does not enumerate + +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m7 \ + -mfloat-abi=hard \ + -mfpu=fpv5-d16 \ + -nostdlib -nostartfiles \ + -DSTM32H745xx \ + -DCORE_CM7 \ + -DCFG_TUSB_MCU=OPT_MCU_STM32H7 \ + -DBOARD_DEVICE_RHPORT_NUM=0 \ + -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED + +# suppress warning caused by vendor mcu driver +CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32H7xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32H7xx + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/STM32H74xXIHx_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32h7xx.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_uart.c \ + $(ST_HAL_DRIVER)/Src/stm32h7xx_hal_pwr_ex.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h745xx.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = synopsys + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM7/r0p1 + +# For flash-jlink target +JLINK_DEVICE = stm32h745xi +JLINK_IF = swd + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32h745disco/stm32h745disco.c b/hw/bsp/stm32h745disco/stm32h745disco.c new file mode 100644 index 000000000..ce4034af0 --- /dev/null +++ b/hw/bsp/stm32h745disco/stm32h745disco.c @@ -0,0 +1,399 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 William D. Jones (thor0505@comcast.net), + * Ha Thach (tinyusb.org) + * Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32h7xx_hal.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ + +// Despite being call USB2_OTG +// OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port +void OTG_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +// Despite being call USB2_OTG +// OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port +void OTG_HS_IRQHandler(void) +{ + tud_int_handler(1); +} + + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PORT GPIOJ +#define LED_PIN GPIO_PIN_2 +#define LED_STATE_ON 1 + +// Blue push-button +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 +#define BUTTON_STATE_ACTIVE 1 + +// UART +#define UARTx USART3 +#define UART_GPIO_PORT GPIOB +#define UART_GPIO_AF GPIO_AF7_USART3 +#define UART_TX_PIN GPIO_PIN_10 +#define UART_RX_PIN GPIO_PIN_11 + +UART_HandleTypeDef UartHandle; + +// enable all LED, Button, Uart, USB clock +static void all_rcc_clk_enable(void) +{ + __HAL_RCC_GPIOA_CLK_ENABLE(); // OTG_FS + __HAL_RCC_GPIOB_CLK_ENABLE(); // USART3 (VCP + __HAL_RCC_GPIOC_CLK_ENABLE(); // Button + __HAL_RCC_GPIOJ_CLK_ENABLE(); // LED + __HAL_RCC_USART3_CLK_ENABLE(); // Uart module +} + +/* PWR, RCC, GPIO (All): AHB4 (D3 domain) + USB{1,2} OTG_{H,F}S: AHB1 (D2 domain) +*/ + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (HSE) + * SYSCLK(Hz) = 400000000 (CPU Clock) + * HCLK(Hz) = 200000000 (AXI and AHBs Clock) + * AHB Prescaler = 2 + * D1 APB3 Prescaler = 2 (APB3 Clock 100MHz) + * D2 APB1 Prescaler = 2 (APB1 Clock 100MHz) + * D2 APB2 Prescaler = 2 (APB2 Clock 100MHz) + * D3 APB4 Prescaler = 2 (APB4 Clock 100MHz) + * HSE Frequency(Hz) = 25000000 + * PLL_M = 5 + * PLL_N = 160 + * PLL_P = 2 + * PLL_Q = 4 + * PLL_R = 2 + * PLL3_M = 25 + * PLL3_N = 336 + * PLL3_P = 2 + * PLL3_Q = 7 + * PLL3_R = 2 + * VDD(V) = 3.3 + * Flash Latency(WS) = 4 + * @param None + * @retval None + */ + +void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_PeriphCLKInitTypeDef PeriphClkInitStruct; + + /*!< Supply configuration update enable */ + /* For STM32H750XB, use "HAL_PWREx_ConfigSupply(PWR_LDO_SUPPLY);" */ + HAL_PWREx_ConfigSupply(PWR_DIRECT_SMPS_SUPPLY); + + /* The voltage scaling allows optimizing the power consumption when the + device is clocked below the maximum system frequency, to update the + voltage scaling value regarding system frequency refer to product + datasheet. */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + while ((PWR->D3CR & (PWR_D3CR_VOSRDY)) != PWR_D3CR_VOSRDY) {} + + /* Enable HSE Oscillator and activate PLL with HSE as source */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; + RCC_OscInitStruct.HSIState = RCC_HSI_OFF; + RCC_OscInitStruct.CSIState = RCC_CSI_OFF; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + + /* PLL1 for System Clock */ + RCC_OscInitStruct.PLL.PLLM = 5; + RCC_OscInitStruct.PLL.PLLN = 160; + RCC_OscInitStruct.PLL.PLLFRACN = 0; + RCC_OscInitStruct.PLL.PLLP = 2; + RCC_OscInitStruct.PLL.PLLR = 2; + RCC_OscInitStruct.PLL.PLLQ = 4; + + RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1VCOMEDIUM; + RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1VCIRANGE_2; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* PLL3 for USB Clock */ + PeriphClkInitStruct.PLL3.PLL3M = 25; + PeriphClkInitStruct.PLL3.PLL3N = 336; + PeriphClkInitStruct.PLL3.PLL3FRACN = 0; + PeriphClkInitStruct.PLL3.PLL3P = 2; + PeriphClkInitStruct.PLL3.PLL3R = 2; + PeriphClkInitStruct.PLL3.PLL3Q = 7; + + PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB; + PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL3; + HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); + + /* Select PLL as system clock source and configure bus clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_D1PCLK1 | RCC_CLOCKTYPE_PCLK1 | \ + RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_D3PCLK1); + + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.SYSCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.AHBCLKDivider = RCC_HCLK_DIV2; + RCC_ClkInitStruct.APB1CLKDivider = RCC_APB1_DIV2; + RCC_ClkInitStruct.APB2CLKDivider = RCC_APB2_DIV2; + RCC_ClkInitStruct.APB3CLKDivider = RCC_APB3_DIV1; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4); + + /*activate CSI clock mondatory for I/O Compensation Cell*/ + __HAL_RCC_CSI_ENABLE() ; + + /* Enable SYSCFG clock mondatory for I/O Compensation Cell */ + __HAL_RCC_SYSCFG_CLK_ENABLE() ; + + /* Enables the I/O Compensation Cell */ + HAL_EnableCompensationCell(); +} + +void board_init(void) +{ + SystemClock_Config(); + all_rcc_clk_enable(); + + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + +#if CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(OTG_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); + NVIC_SetPriority(OTG_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); +#endif + + GPIO_InitTypeDef GPIO_InitStruct; + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UARTx; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + HAL_UART_Init(&UartHandle); + +#if BOARD_DEVICE_RHPORT_NUM == 0 + // Despite being call USB2_OTG + // OTG_FS is marked as RHPort0 by TinyUSB to be consistent across stm32 port + // PA9 VUSB, PA10 ID, PA11 DM, PA12 DP + + __HAL_RCC_GPIOA_CLK_ENABLE(); + + /* Configure DM DP Pins */ + GPIO_InitStruct.Pin = GPIO_PIN_11 | GPIO_PIN_12; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG1_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure VBUS Pin */ + GPIO_InitStruct.Pin = GPIO_PIN_9; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* This for ID line debug */ + GPIO_InitStruct.Pin = GPIO_PIN_10; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG1_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + // https://community.st.com/s/question/0D50X00009XkYZLSA3/stm32h7-nucleo-usb-fs-cdc + // TODO: Board init actually works fine without this line. +// HAL_PWREx_EnableUSBVoltageDetector(); + __HAL_RCC_USB2_OTG_FS_CLK_ENABLE(); + + // Enable VBUS sense (B device) via pin PA9 + USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; + +#elif BOARD_DEVICE_RHPORT_NUM == 1 + + // Despite being call USB2_OTG + // OTG_HS is marked as RHPort1 by TinyUSB to be consistent across stm32 port + __GPIOA_CLK_ENABLE(); + __GPIOB_CLK_ENABLE(); + __GPIOC_CLK_ENABLE(); + __GPIOH_CLK_ENABLE(); + __GPIOI_CLK_ENABLE(); + + /* CLK */ + GPIO_InitStruct.Pin = GPIO_PIN_5; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* D0 */ + GPIO_InitStruct.Pin = GPIO_PIN_3; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* D1 D2 D3 D4 D5 D6 D7 */ + GPIO_InitStruct.Pin = GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_5 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 | GPIO_PIN_13; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + /* STP */ + GPIO_InitStruct.Pin = GPIO_PIN_0; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + + /* NXT */ + GPIO_InitStruct.Pin = GPIO_PIN_4; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOH, &GPIO_InitStruct); + + /* DIR */ + GPIO_InitStruct.Pin = GPIO_PIN_11; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG2_HS; + HAL_GPIO_Init(GPIOI, &GPIO_InitStruct); + + // Enable ULPI clock + __HAL_RCC_USB1_OTG_HS_ULPI_CLK_ENABLE(); + + /* Enable USB HS Clocks */ + __HAL_RCC_USB1_OTG_HS_CLK_ENABLE(); + + // No VBUS sense + USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // B-peripheral session valid override enable + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + + // Force device mode + USB_OTG_HS->GUSBCFG &= ~USB_OTG_GUSBCFG_FHMOD; + USB_OTG_HS->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD; + + HAL_PWREx_EnableUSBVoltageDetector(); +#endif // rhport = 1 + +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + return (BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN)) ? 1 : 0; +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + return len; +} + + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32h745disco/stm32h7xx_hal_conf.h b/hw/bsp/stm32h745disco/stm32h7xx_hal_conf.h new file mode 100644 index 000000000..b9fa348ec --- /dev/null +++ b/hw/bsp/stm32h745disco/stm32h7xx_hal_conf.h @@ -0,0 +1,482 @@ +/** + ****************************************************************************** + * @file stm32h7xx_hal_conf_template.h + * @brief HAL configuration template file. + * This file should be copied to the application folder and renamed + * to stm32h7xx_hal_conf.h. + ****************************************************************************** + * @attention + * + *

© COPYRIGHT(c) 2019 STMicroelectronics

+ * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32H7xx_HAL_CONF_H +#define __STM32H7xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_COMP_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_DCMI_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_DMA2D_MODULE_ENABLED */ +/* #define HAL_ETH_MODULE_ENABLED */ +/* #define HAL_EXTI_MODULE_ENABLED */ +/* #define HAL_FDCAN_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +/* #define HAL_HASH_MODULE_ENABLED */ +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_HRTIM_MODULE_ENABLED */ +/* #define HAL_HSEM_MODULE_ENABLED */ +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_JPEG_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_LTDC_MODULE_ENABLED */ +/* #define HAL_MDIOS_MODULE_ENABLED */ +/* #define HAL_MDMA_MODULE_ENABLED */ +/* #define HAL_MMC_MODULE_ENABLED */ +/* #define HAL_NAND_MODULE_ENABLED */ +/* #define HAL_NOR_MODULE_ENABLED */ +/* #define HAL_OPAMP_MODULE_ENABLED */ +/* #define HAL_PCD_MODULE_ENABLED */ +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +/* #define HAL_RAMECC_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SAI_MODULE_ENABLED */ +/* #define HAL_SD_MODULE_ENABLED */ +/* #define HAL_SDRAM_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_SMBUS_MODULE_ENABLED */ +/* #define HAL_SPDIFRX_MODULE_ENABLED */ +#define HAL_SPI_MODULE_ENABLED +/* #define HAL_SRAM_MODULE_ENABLED */ +/* #define HAL_SWPMI_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) +#define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal oscillator (CSI) default value. + * This value is the default CSI value after Reset. + */ +#if !defined (CSI_VALUE) + #define CSI_VALUE ((uint32_t)4000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* CSI_VALUE */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE ((uint32_t)64000000) /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +#if !defined (LSI_VALUE) + #define LSI_VALUE ((uint32_t)32000) /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature.*/ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#if !defined (EXTERNAL_CLOCK_VALUE) + #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External clock in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY ((uint32_t)0x0F) /*!< tick interrupt priority */ +#define USE_RTOS 0 +#define USE_SD_TRANSCEIVER 1U /*!< use uSD Transceiver */ +#define USE_SPI_CRC 1U /*!< use CRC in SPI */ + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_COMP_REGISTER_CALLBACKS 0U /* COMP register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_FDCAN_REGISTER_CALLBACKS 0U /* FDCAN register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_HRTIM_REGISTER_CALLBACKS 0U /* HRTIM register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_JPEG_REGISTER_CALLBACKS 0U /* JPEG register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MDIOS_REGISTER_CALLBACKS 0U /* MDIO register callback disabled */ +#define USE_HAL_OPAMP_REGISTER_CALLBACKS 0U /* MDIO register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_SWPMI_REGISTER_CALLBACKS 0U /* SWPMI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################### Ethernet Configuration ######################### */ +#define ETH_TX_DESC_CNT 4 /* number of Ethernet Tx DMA descriptors */ +#define ETH_RX_DESC_CNT 4 /* number of Ethernet Rx DMA descriptors */ + +#define ETH_MAC_ADDR0 ((uint8_t)0x02) +#define ETH_MAC_ADDR1 ((uint8_t)0x00) +#define ETH_MAC_ADDR2 ((uint8_t)0x00) +#define ETH_MAC_ADDR3 ((uint8_t)0x00) +#define ETH_MAC_ADDR4 ((uint8_t)0x00) +#define ETH_MAC_ADDR5 ((uint8_t)0x00) + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1 */ + + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32h7xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32h7xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32h7xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_MDMA_MODULE_ENABLED + #include "stm32h7xx_hal_mdma.h" +#endif /* HAL_MDMA_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32h7xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32h7xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32h7xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32h7xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32h7xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32h7xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED + #include "stm32h7xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32h7xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32h7xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_FDCAN_MODULE_ENABLED + #include "stm32h7xx_hal_fdcan.h" +#endif /* HAL_FDCAN_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32h7xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED + #include "stm32h7xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32h7xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32h7xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32h7xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32h7xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_HRTIM_MODULE_ENABLED + #include "stm32h7xx_hal_hrtim.h" +#endif /* HAL_HRTIM_MODULE_ENABLED */ + +#ifdef HAL_HSEM_MODULE_ENABLED + #include "stm32h7xx_hal_hsem.h" +#endif /* HAL_HSEM_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32h7xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32h7xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32h7xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32h7xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32h7xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32h7xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_JPEG_MODULE_ENABLED + #include "stm32h7xx_hal_jpeg.h" +#endif /* HAL_JPEG_MODULE_ENABLED */ + +#ifdef HAL_MDIOS_MODULE_ENABLED + #include "stm32h7xx_hal_mdios.h" +#endif /* HAL_MDIOS_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED + #include "stm32h7xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32h7xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED +#include "stm32h7xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_OPAMP_MODULE_ENABLED +#include "stm32h7xx_hal_opamp.h" +#endif /* HAL_OPAMP_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32h7xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32h7xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RAMECC_MODULE_ENABLED + #include "stm32h7xx_hal_ramecc.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32h7xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32h7xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32h7xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32h7xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32h7xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32h7xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32h7xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_SWPMI_MODULE_ENABLED + #include "stm32h7xx_hal_swpmi.h" +#endif /* HAL_SWPMI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32h7xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32h7xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32h7xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32h7xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32h7xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32h7xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32h7xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32h7xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32h7xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t *file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32H7xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit v1.3.1 From 5c24d5ca72d6657b1be03ded699fdf525abb0525 Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Thu, 2 Jul 2020 19:40:32 +0200 Subject: stm32h745disco: HAL_PWREx_EnableUSBVoltageDetector() is needed for hot replug. --- hw/bsp/stm32h745disco/stm32h745disco.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stm32h745disco/stm32h745disco.c b/hw/bsp/stm32h745disco/stm32h745disco.c index ce4034af0..d4fcdbfc0 100644 --- a/hw/bsp/stm32h745disco/stm32h745disco.c +++ b/hw/bsp/stm32h745disco/stm32h745disco.c @@ -263,8 +263,7 @@ void board_init(void) HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); // https://community.st.com/s/question/0D50X00009XkYZLSA3/stm32h7-nucleo-usb-fs-cdc - // TODO: Board init actually works fine without this line. -// HAL_PWREx_EnableUSBVoltageDetector(); + HAL_PWREx_EnableUSBVoltageDetector(); __HAL_RCC_USB2_OTG_FS_CLK_ENABLE(); // Enable VBUS sense (B device) via pin PA9 -- cgit v1.3.1 From 11c6d4cdaea007cbe804dfc7d512bd82562e41d2 Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Fri, 3 Jul 2020 10:59:02 +0200 Subject: stlinkv3mini: Only OTG_HS has connector. --- hw/bsp/stlinkv3mini/board.mk | 14 +++++--------- 1 file changed, 5 insertions(+), 9 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/stlinkv3mini/board.mk b/hw/bsp/stlinkv3mini/board.mk index 47148ec4d..b77fb5a51 100644 --- a/hw/bsp/stlinkv3mini/board.mk +++ b/hw/bsp/stlinkv3mini/board.mk @@ -1,4 +1,5 @@ -PORT ?= 1 +# Only OTG-HS has a connector on this board + REDUCE_SPEED ?= 0 CFLAGS += \ @@ -12,18 +13,13 @@ CFLAGS += \ -DSTM32F723xx \ -DHSE_VALUE=25000000 \ -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ - -DBOARD_DEVICE_RHPORT_NUM=$(PORT) - -ifeq ($(PORT), 1) - ifeq ($(REDUCE_SPEED), 0) + -DBOARD_DEVICE_RHPORT_NUM=1 +ifeq ($(REDUCE_SPEED), 0) CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED $(info "Using OTG_HS in HS mode") - else +else CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED $(info "Using OTG_HS in FS mode") - endif -else -$(info "Using OTG_FS") endif # mcu driver cause following warnings -- cgit v1.3.1 From 8f433e67ac8dda31f3798f900b698454476730bc Mon Sep 17 00:00:00 2001 From: Uwe Bonnes Date: Fri, 3 Jul 2020 15:47:35 +0200 Subject: Add stm32l4r5nucleo. USB and UARTwork. USB runs from LSE stabilized MSI48 LPUART on PORTG needs VDDIO2 enabled. --- hw/bsp/stm32l4r5nucleo/STM32L4RXxI_FLASH.ld | 167 ++++++++++++ hw/bsp/stm32l4r5nucleo/board.mk | 49 ++++ hw/bsp/stm32l4r5nucleo/stm32l4r5nucleo.c | 287 +++++++++++++++++++++ hw/bsp/stm32l4r5nucleo/stm32l4xx_hal_conf.h | 382 ++++++++++++++++++++++++++++ 4 files changed, 885 insertions(+) create mode 100644 hw/bsp/stm32l4r5nucleo/STM32L4RXxI_FLASH.ld create mode 100644 hw/bsp/stm32l4r5nucleo/board.mk create mode 100644 hw/bsp/stm32l4r5nucleo/stm32l4r5nucleo.c create mode 100644 hw/bsp/stm32l4r5nucleo/stm32l4xx_hal_conf.h (limited to 'hw/bsp') diff --git a/hw/bsp/stm32l4r5nucleo/STM32L4RXxI_FLASH.ld b/hw/bsp/stm32l4r5nucleo/STM32L4RXxI_FLASH.ld new file mode 100644 index 000000000..f93a16041 --- /dev/null +++ b/hw/bsp/stm32l4r5nucleo/STM32L4RXxI_FLASH.ld @@ -0,0 +1,167 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32L4RxI Device with +** 2048KByte FLASH, 640KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +** (c)Copyright Ac6. +** You may use this file as-is or modify it according to the needs of your +** project. Distribution of this file (unmodified or modified) is not +** permitted. Ac6 permit registered System Workbench for MCU users the +** rights to distribute the assembled, compiled & linked contents of this +** file as part of an application binary file, provided that it is built +** using the System Workbench for MCU toolchain. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x200a0000; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x460; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 640K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 2048K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/stm32l4r5nucleo/board.mk b/hw/bsp/stm32l4r5nucleo/board.mk new file mode 100644 index 000000000..8ccefb7f8 --- /dev/null +++ b/hw/bsp/stm32l4r5nucleo/board.mk @@ -0,0 +1,49 @@ +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m4 \ + -mfloat-abi=hard \ + -mfpu=fpv4-sp-d16 \ + -nostdlib -nostartfiles \ + -DHSE_VALUE=8000000 \ + -DSTM32L4R5xx \ + -DCFG_TUSB_MCU=OPT_MCU_STM32L4 + +# suppress warning caused by vendor mcu driver +CFLAGS += -Wno-error=maybe-uninitialized -Wno-error=cast-align + +ST_HAL_DRIVER = hw/mcu/st/st_driver/STM32L4xx_HAL_Driver +ST_CMSIS = hw/mcu/st/st_driver/CMSIS/Device/ST/STM32L4xx + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/STM32L4RXxI_FLASH.ld + +SRC_C += \ + $(ST_CMSIS)/Source/Templates/system_stm32l4xx.c \ + $(ST_HAL_DRIVER)/Src/stm32l4xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32l4xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32l4xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32l4xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32l4xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32l4xx_hal_uart.c \ + $(ST_HAL_DRIVER)/Src/stm32l4xx_hal_pwr_ex.c + +SRC_S += \ + $(ST_CMSIS)/Source/Templates/gcc/startup_stm32l4r5xx.s + +INC += \ + $(TOP)/hw/mcu/st/st_driver/CMSIS/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc \ + $(TOP)/hw/bsp/$(BOARD) + +# For TinyUSB port source +VENDOR = st +CHIP_FAMILY = synopsys + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM4F + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32l4r5nucleo/stm32l4r5nucleo.c b/hw/bsp/stm32l4r5nucleo/stm32l4r5nucleo.c new file mode 100644 index 000000000..bab66b550 --- /dev/null +++ b/hw/bsp/stm32l4r5nucleo/stm32l4r5nucleo.c @@ -0,0 +1,287 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 William D. Jones (thor0505@comcast.net), + * Ha Thach (tinyusb.org) + * Uwe Bonnes (bon@elektron.ikp.physik.tu-darmstadt.de) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "../board.h" + +#include "stm32l4xx_hal.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void OTG_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +#define LED_PORT GPIOB +#define LED_PIN GPIO_PIN_14 +#define LED_STATE_ON 1 + +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 +#define BUTTON_STATE_ACTIVE 1 + +#define UARTx LPUART1 +#define UART_GPIO_PORT GPIOG +#define UART_GPIO_AF GPIO_AF8_LPUART1 +#define UART_TX_PIN GPIO_PIN_7 +#define UART_RX_PIN GPIO_PIN_8 + +UART_HandleTypeDef UartHandle; + +// enable all LED, Button, Uart, USB clock +static void all_rcc_clk_enable(void) +{ + __HAL_RCC_GPIOA_CLK_ENABLE(); // USB D+, D- + __HAL_RCC_GPIOB_CLK_ENABLE(); // LED + __HAL_RCC_GPIOC_CLK_ENABLE(); // Button + __HAL_RCC_GPIOG_CLK_ENABLE(); // Uart TX, RX + __HAL_RCC_LPUART1_CLK_ENABLE(); // LPUart1 module +} + +/** + * @brief System Clock Configuration + * The system Clock is configured as follow : + * System Clock source = PLL (MSI) + * SYSCLK(Hz) = 120000000 + * HCLK(Hz) = 120000000 + * AHB Prescaler = 1 + * APB1 Prescaler = 1 + * APB2 Prescaler = 1 + * MSI Frequency(Hz) = 48000000 + * PLL_M = 12 + * PLL_N = 60 + * PLL_P = 2 + * PLL_Q = 2 + * VDD(V) = 3.3 + * Main regulator output voltage = Scale1 mode + * Flash Latency(WS) = 5 + * The USB clock configuration from PLLSAI: + * PLLSAIP = 8 FIXME + * PLLSAIN = 384 FIXME + * PLLSAIQ = 7 FIXME + * @param None + * @retval None + */ +void SystemClock_Config(void) +{ + RCC_ClkInitTypeDef RCC_ClkInitStruct; + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0}; + + /* Activate PLL with MSI , stabilizied via PLL by LSE */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_MSI; + RCC_OscInitStruct.MSIState = RCC_MSI_ON; + RCC_OscInitStruct.LSEState = RCC_LSE_ON; + RCC_OscInitStruct.MSIClockRange = RCC_MSIRANGE_11; + RCC_OscInitStruct.MSICalibrationValue = RCC_MSICALIBRATION_DEFAULT; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_MSI; + RCC_OscInitStruct.PLL.PLLM = 12; + RCC_OscInitStruct.PLL.PLLN = 60; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = 2; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /* Enable MSI Auto-calibration through LSE */ + HAL_RCCEx_EnableMSIPLLMode(); + + /* Select MSI output as USB clock source */ + PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB; + PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_MSI; + HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); + + /* Select MSI output as USB clock source */ + PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_LPUART1; + PeriphClkInitStruct.Lpuart1ClockSelection = RCC_LPUART1CLKSOURCE_PCLK1; + HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 + clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + // Avoid overshoot and start with HCLK 60 MHz + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV2; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_3); + + /* AHB prescaler divider at 1 as second step */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5); +} + +void board_init(void) +{ + /* Enable Power Clock*/ + __HAL_RCC_PWR_CLK_ENABLE(); + /* Enable voltage range 1 boost mode for frequency above 80 Mhz */ + HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1_BOOST); + + /* Set tick interrupt priority, default HAL value is intentionally invalid + and that prevents PLL initialization in HAL_RCC_OscConfig() */ + + HAL_InitTick((1UL << __NVIC_PRIO_BITS) - 1UL); + + SystemClock_Config(); + all_rcc_clk_enable(); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#elif CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + //NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); +#endif + + /* Enable USB power on Pwrctrl CR2 register */ + HAL_PWREx_EnableVddUSB(); + + GPIO_InitTypeDef GPIO_InitStruct; + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + // IOSV bit MUST be set to access GPIO port G[2:15] */ + __HAL_RCC_PWR_CLK_ENABLE(); + HAL_PWREx_EnableVddIO2(); + + // Uart + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle.Instance = UARTx; + UartHandle.Init.BaudRate = CFG_BOARD_UART_BAUDRATE; + UartHandle.Init.WordLength = UART_WORDLENGTH_8B; + UartHandle.Init.StopBits = UART_STOPBITS_1; + UartHandle.Init.Parity = UART_PARITY_NONE; + UartHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE; + UartHandle.Init.Mode = UART_MODE_TX_RX; + UartHandle.Init.OverSampling = UART_OVERSAMPLING_16; + UartHandle.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE; + UartHandle.Init.ClockPrescaler = UART_PRESCALER_DIV1; + UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT; + + HAL_UART_Init(&UartHandle); + + /* Configure USB FS GPIOs */ + /* Configure DM DP Pins */ + GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure VBUS Pin */ + GPIO_InitStruct.Pin = GPIO_PIN_9; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Configure ID pin */ + GPIO_InitStruct.Pin = GPIO_PIN_10; + GPIO_InitStruct.Mode = GPIO_MODE_AF_OD; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Enable USB FS Clocks */ + __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); + + // Enable VBUS sense (B device) via pin PA9 + USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + HAL_GPIO_WritePin(LED_PORT, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +} + +uint32_t board_button_read(void) +{ + return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + HAL_UART_Transmit(&UartHandle, (uint8_t*) buf, len, 0xffff); + return len; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +void HardFault_Handler (void) +{ + asm("bkpt"); +} + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32l4r5nucleo/stm32l4xx_hal_conf.h b/hw/bsp/stm32l4r5nucleo/stm32l4xx_hal_conf.h new file mode 100644 index 000000000..66822ff59 --- /dev/null +++ b/hw/bsp/stm32l4r5nucleo/stm32l4xx_hal_conf.h @@ -0,0 +1,382 @@ +/** + ****************************************************************************** + * @file stm32l4xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration template file. + * This file should be copied to the application folder and renamed + * to stm32l4xx_hal_conf.h. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32L4xx_HAL_CONF_H +#define __STM32L4xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/* #define HAL_ADC_MODULE_ENABLED */ +/* #define HAL_CAN_MODULE_ENABLED */ +/* #define HAL_CAN_LEGACY_MODULE_ENABLED */ +/* #define HAL_COMP_MODULE_ENABLED */ +#define HAL_CORTEX_MODULE_ENABLED +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_DFSDM_MODULE_ENABLED */ +#define HAL_DMA_MODULE_ENABLED +/* #define HAL_FIREWALL_MODULE_ENABLED */ +#define HAL_FLASH_MODULE_ENABLED +/* #define HAL_NAND_MODULE_ENABLED */ +#define HAL_NOR_MODULE_ENABLED +#define HAL_SRAM_MODULE_ENABLED +/* #define HAL_HCD_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +//#define HAL_I2C_MODULE_ENABLED +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +//#define HAL_LCD_MODULE_ENABLED +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_OPAMP_MODULE_ENABLED */ +//#define HAL_PCD_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +/* #define HAL_QSPI_MODULE_ENABLED */ +#define HAL_RCC_MODULE_ENABLED +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +//#define HAL_SAI_MODULE_ENABLED +//#define HAL_SD_MODULE_ENABLED +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_SMBUS_MODULE_ENABLED */ +/* #define HAL_SPI_MODULE_ENABLED */ +/* #define HAL_SWPMI_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +/* #define HAL_TSC_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ + + +/* ########################## Oscillator Values adaptation ####################*/ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) + #define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) + #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal Multiple Speed oscillator (MSI) default value. + * This value is the default MSI range value after Reset. + */ +#if !defined (MSI_VALUE) + #define MSI_VALUE 4000000U /*!< Value of the Internal oscillator in Hz*/ +#endif /* MSI_VALUE */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) + #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal High Speed oscillator (HSI48) value for USB FS, SDMMC and RNG. + * This internal oscillator is mainly dedicated to provide a high precision clock to + * the USB peripheral by means of a special Clock Recovery System (CRS) circuitry. + * When the CRS is not used, the HSI48 RC oscillator runs on it default frequency + * which is subject to manufacturing process variations. + */ +#if !defined (HSI48_VALUE) + #define HSI48_VALUE 48000000U /*!< Value of the Internal High Speed oscillator for USB FS/SDMMC/RNG in Hz. + The real value my vary depending on manufacturing process variations.*/ +#endif /* HSI48_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) + #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature.*/ +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) + #define LSE_VALUE 32768U /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) + #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for SAI1 peripheral + * This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source + * frequency. + */ +#if !defined (EXTERNAL_SAI1_CLOCK_VALUE) + #define EXTERNAL_SAI1_CLOCK_VALUE 48000U /*!< Value of the SAI1 External clock source in Hz*/ +#endif /* EXTERNAL_SAI1_CLOCK_VALUE */ + +/** + * @brief External clock source for SAI2 peripheral + * This value is used by the RCC HAL module to compute the SAI1 & SAI2 clock source + * frequency. + */ +#if !defined (EXTERNAL_SAI2_CLOCK_VALUE) + #define EXTERNAL_SAI2_CLOCK_VALUE 48000U /*!< Value of the SAI2 External clock source in Hz*/ +#endif /* EXTERNAL_SAI2_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE 3300U /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY 0U /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 0U +#define INSTRUCTION_CACHE_ENABLE 1U +#define DATA_CACHE_ENABLE 1U + +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1U */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver + * Activated: CRC code is present inside driver + * Deactivated: CRC code cleaned from driver + */ + +#define USE_SPI_CRC 1U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32l4xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32l4xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32l4xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32l4xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32l4xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32l4xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32l4xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED + #include "Legacy/stm32l4xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED + #include "stm32l4xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32l4xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32l4xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32l4xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_FIREWALL_MODULE_ENABLED + #include "stm32l4xx_hal_firewall.h" +#endif /* HAL_FIREWALL_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32l4xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32l4xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32l4xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32l4xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32l4xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32l4xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LCD_MODULE_ENABLED + #include "stm32l4xx_hal_lcd.h" +#endif /* HAL_LCD_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32l4xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_OPAMP_MODULE_ENABLED +#include "stm32l4xx_hal_opamp.h" +#endif /* HAL_OPAMP_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32l4xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32l4xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32l4xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32l4xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32l4xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32l4xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32l4xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32l4xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_SWPMI_MODULE_ENABLED + #include "stm32l4xx_hal_swpmi.h" +#endif /* HAL_SWPMI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32l4xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_TSC_MODULE_ENABLED + #include "stm32l4xx_hal_tsc.h" +#endif /* HAL_TSC_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32l4xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32l4xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32l4xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32l4xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32l4xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32l4xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32l4xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr: If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t *file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32L4xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -- cgit v1.3.1 From 0fd074afd85d84f162ddebbc9b8e009f9136809b Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 8 Jul 2020 16:29:48 +0700 Subject: change REDUCE_SPEED=0/1 to explicitly SPEED=high/full update readme, boards.md to add link to new stm boards --- docs/boards.md | 2 ++ examples/readme.md | 31 +++++++++++++++++++++---------- hw/bsp/stlinkv3mini/board.mk | 13 +++++++------ hw/bsp/stm32f723disco/board.mk | 18 +++++++++--------- hw/bsp/stm32f746disco/board.mk | 18 +++++++++--------- hw/bsp/stm32f769disco/board.mk | 14 ++++++++------ src/portable/st/synopsys/dcd_synopsys.c | 2 +- 7 files changed, 57 insertions(+), 41 deletions(-) (limited to 'hw/bsp') diff --git a/docs/boards.md b/docs/boards.md index d3dcec375..271ca2844 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -87,6 +87,7 @@ This code base already had supported for a handful of following boards (sorted a - [Micro Python PyBoard v1.1](https://store.micropython.org/product/PYBv1.1) - [STLink-V3 Mini](https://www.st.com/en/development-tools/stlink-v3mini.html) - [STM32 L035c8 Discovery](https://www.st.com/en/evaluation-tools/32l0538discovery.html) +- [STM32 L4R5zi Nucleo](https://www.st.com/en/evaluation-tools/nucleo-l4r5zi.html) - [STM32 F070rb Nucleo](https://www.st.com/en/evaluation-tools/nucleo-f070rb.html) - [STM32 F072rb Discovery](https://www.st.com/en/evaluation-tools/32f072bdiscovery.html) - STM32 F103c Blue Pill @@ -104,6 +105,7 @@ This code base already had supported for a handful of following boards (sorted a - [STM32 F769i Discovery](https://www.st.com/en/evaluation-tools/32f769idiscovery.html) - [STM32 H743zi Nucleo](https://www.st.com/en/evaluation-tools/nucleo-h743zi.html) - [STM32 H743i Evaluation](https://www.st.com/en/evaluation-tools/stm32h743i-eval.html) +- [STM32 H745i Discovery](https://www.st.com/en/evaluation-tools/stm32h745i-disco.html) ### TI diff --git a/examples/readme.md b/examples/readme.md index 790427cd2..f6cd380b6 100644 --- a/examples/readme.md +++ b/examples/readme.md @@ -32,28 +32,39 @@ Then compile with `make BOARD=[your_board] all`, for example $ make BOARD=feather_nrf52840_express all ``` +**Port Selection** -To compile for debugging with debug symbols add DEBUG=1, for example +If a board has several ports, one port is chosen by default in the individual board.mk file. Use option `PORT=x` To choose another port. For example to select the HS port of a STM32F746Disco board, use: ``` -$ make BOARD=feather_nrf52840_express DEBUG=1 all -If a board has several ports, one port is choosen by default in the individual board.mk file. Choose another port with PORT=x. For example to select the HS port of a STM32F746Disco board, use: +$ make BOARD=stm32f746disco PORT=1 all +``` + +**Port Speed** + +A MCU can support multiple operational speed. By default, the example build system will use the fastest supported on the board. Use option `SPEED=full/high` e.g To force F723 operate at full instead of default high speed ``` -$ make BOARD=stm32f746disco PORT=1 all +$ make BOARD=stm32f746disco SPEED=full all ``` -### Debug Log +### Debug + +To compile for debugging with debug symbols add `DEBUG=1`, for example + +``` +$ make BOARD=feather_nrf52840_express DEBUG=1 all +``` -### Log Level +#### Log Should you have an issue running example and/or submitting an bug report. You could enable TinyUSB built-in debug logging with optional `LOG=`. LOG=1 will only print out error message, LOG=2 print more information with on-going events. LOG=3 or higher is not used yet. ``` -$ make LOG=2 BOARD=feather_nrf52840_express all +$ make BOARD=feather_nrf52840_express LOG=2 all ``` -### Logger +#### Logger By default log message is printed via on-board UART which is slow and take lots of CPU time comparing to USB speed. If your board support on-board/external debugger, it would be more efficient to use it for logging. There are 2 protocols: @@ -67,8 +78,8 @@ By default log message is printed via on-board UART which is slow and take lots - Software viewer should be provided along with your debugger driver. ``` -$ make LOG=2 LOGGER=rtt BOARD=feather_nrf52840_express all -$ make LOG=2 LOGGER=swo BOARD=feather_nrf52840_express all +$ make BOARD=feather_nrf52840_express LOG=2 LOGGER=rtt all +$ make BOARD=feather_nrf52840_express LOG=2 LOGGER=swo all ``` ## Flash diff --git a/hw/bsp/stlinkv3mini/board.mk b/hw/bsp/stlinkv3mini/board.mk index b77fb5a51..4ca6cfd68 100644 --- a/hw/bsp/stlinkv3mini/board.mk +++ b/hw/bsp/stlinkv3mini/board.mk @@ -1,6 +1,6 @@ # Only OTG-HS has a connector on this board -REDUCE_SPEED ?= 0 +SPEED ?= high CFLAGS += \ -flto \ @@ -14,12 +14,13 @@ CFLAGS += \ -DHSE_VALUE=25000000 \ -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ -DBOARD_DEVICE_RHPORT_NUM=1 -ifeq ($(REDUCE_SPEED), 0) -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED -$(info "Using OTG_HS in HS mode") + +ifeq ($(SPEED), high) + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + $(info "Using OTG_HS in HighSpeed mode") else -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED -$(info "Using OTG_HS in FS mode") + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED + $(info "Using OTG_HS in FullSpeed mode") endif # mcu driver cause following warnings diff --git a/hw/bsp/stm32f723disco/board.mk b/hw/bsp/stm32f723disco/board.mk index 47148ec4d..9ec23bfde 100644 --- a/hw/bsp/stm32f723disco/board.mk +++ b/hw/bsp/stm32f723disco/board.mk @@ -1,5 +1,5 @@ PORT ?= 1 -REDUCE_SPEED ?= 0 +SPEED ?= high CFLAGS += \ -flto \ @@ -15,15 +15,15 @@ CFLAGS += \ -DBOARD_DEVICE_RHPORT_NUM=$(PORT) ifeq ($(PORT), 1) - ifeq ($(REDUCE_SPEED), 0) -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED -$(info "Using OTG_HS in HS mode") - else -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED -$(info "Using OTG_HS in FS mode") - endif + ifeq ($(SPEED), high) + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + $(info "Using OTG_HS in HighSpeed mode") + else + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED + $(info "Using OTG_HS in FullSpeed mode") + endif else -$(info "Using OTG_FS") + $(info "Using OTG_FS") endif # mcu driver cause following warnings diff --git a/hw/bsp/stm32f746disco/board.mk b/hw/bsp/stm32f746disco/board.mk index d7329a28f..48cb3f141 100644 --- a/hw/bsp/stm32f746disco/board.mk +++ b/hw/bsp/stm32f746disco/board.mk @@ -1,5 +1,5 @@ PORT ?= 0 -REDUCE_SPEED ?= 0 +SPEED ?= high CFLAGS += \ -flto \ @@ -15,15 +15,15 @@ CFLAGS += \ -DBOARD_DEVICE_RHPORT_NUM=$(PORT) ifeq ($(PORT), 1) - ifeq ($(REDUCE_SPEED), 0) -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED -$(info "Using OTG_HS in HS mode") - else -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED -$(info "Using OTG_HS in FS mode") - endif + ifeq ($(SPEED), high) + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + $(info "Using OTG_HS in HighSpeed mode") + else + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED + $(info "Using OTG_HS in FullSpeed mode") + endif else -$(info "Using OTG_FS") + $(info "Using OTG_FS") endif # mcu driver cause following warnings diff --git a/hw/bsp/stm32f769disco/board.mk b/hw/bsp/stm32f769disco/board.mk index 43b677ddd..962dddc68 100644 --- a/hw/bsp/stm32f769disco/board.mk +++ b/hw/bsp/stm32f769disco/board.mk @@ -1,4 +1,6 @@ -REDUCE_SPEED ?= 0 +# Only OTG-HS has a connector on this board + +SPEED ?= high CFLAGS += \ -flto \ @@ -13,12 +15,12 @@ CFLAGS += \ -DCFG_TUSB_MCU=OPT_MCU_STM32F7 \ -DBOARD_DEVICE_RHPORT_NUM=1 \ -ifeq ($(REDUCE_SPEED), 0) -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED -$(info "Using OTG_HS in HS mode") +ifeq ($(SPEED), high) + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_HIGH_SPEED + $(info "Using OTG_HS in HighSpeed mode") else -CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED -$(info "Using OTG_HS in FS mode") + CFLAGS += -DBOARD_DEVICE_RHPORT_SPEED=OPT_MODE_FULL_SPEED + $(info "Using OTG_HS in FullSpeed mode") endif # suppress warning caused by vendor mcu driver diff --git a/src/portable/st/synopsys/dcd_synopsys.c b/src/portable/st/synopsys/dcd_synopsys.c index 35b7f44f9..7eb63e52f 100644 --- a/src/portable/st/synopsys/dcd_synopsys.c +++ b/src/portable/st/synopsys/dcd_synopsys.c @@ -403,7 +403,7 @@ void dcd_init (uint8_t rhport) // Select default internal VBUS Indicator and Drive for ULPI usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_ULPIEVBUSD | USB_OTG_GUSBCFG_ULPIEVBUSI); - #if defined(USB_HS_PHYC) +#if defined(USB_HS_PHYC) // Highspeed with embedded UTMI PHYC // Select UTMI Interface -- cgit v1.3.1 From 9181ce55fb47d17b3ef5d77896537d5fd24090ff Mon Sep 17 00:00:00 2001 From: Kate Temkin Date: Mon, 23 Dec 2019 04:07:47 -0700 Subject: add BSP for Great Scott Gadgets' LUNA boards (SAMD21) --- docs/boards.md | 1 + hw/bsp/luna/board.mk | 47 +++++++++++++ hw/bsp/luna/luna.c | 144 ++++++++++++++++++++++++++++++++++++++++ hw/bsp/luna/samd21g18a_flash.ld | 144 ++++++++++++++++++++++++++++++++++++++++ 4 files changed, 336 insertions(+) create mode 100644 hw/bsp/luna/board.mk create mode 100644 hw/bsp/luna/luna.c create mode 100644 hw/bsp/luna/samd21g18a_flash.ld (limited to 'hw/bsp') diff --git a/docs/boards.md b/docs/boards.md index 271ca2844..53dc95397 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -29,6 +29,7 @@ This code base already had supported for a handful of following boards (sorted a - [Adafruit Metro M0 Express](https://www.adafruit.com/product/3505) - [Adafruit Metro M4 Express](https://www.adafruit.com/product/3382) - [Seeeduino Xiao](https://www.seeedstudio.com/Seeeduino-XIAO-Arduino-Microcontroller-SAMD21-Cortex-M0+-p-4426.html) +- [Great Scott Gadgets LUNA](https://greatscottgadgets.com/luna/) ### Nordic nRF5x diff --git a/hw/bsp/luna/board.mk b/hw/bsp/luna/board.mk new file mode 100644 index 000000000..44f6fd75b --- /dev/null +++ b/hw/bsp/luna/board.mk @@ -0,0 +1,47 @@ +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs-linux \ + -mcpu=cortex-m0plus \ + -nostdlib -nostartfiles \ + -D__SAMD21G18A__ \ + -DCONF_DFLL_OVERWRITE_CALIBRATION=0 \ + -DCFG_TUSB_MCU=OPT_MCU_SAMD21 + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/samd21g18a_flash.ld + +SRC_C += \ + hw/mcu/microchip/samd/asf4/samd21/gcc/gcc/startup_samd21.c \ + hw/mcu/microchip/samd/asf4/samd21/gcc/system_samd21.c \ + hw/mcu/microchip/samd/asf4/samd21/hpl/gclk/hpl_gclk.c \ + hw/mcu/microchip/samd/asf4/samd21/hpl/pm/hpl_pm.c \ + hw/mcu/microchip/samd/asf4/samd21/hpl/sysctrl/hpl_sysctrl.c \ + hw/mcu/microchip/samd/asf4/samd21/hal/src/hal_atomic.c + +INC += \ + $(TOP)/hw/mcu/microchip/samd/asf4/samd21/ \ + $(TOP)/hw/mcu/microchip/samd/asf4/samd21/config \ + $(TOP)/hw/mcu/microchip/samd/asf4/samd21/include \ + $(TOP)/hw/mcu/microchip/samd/asf4/samd21/hal/include \ + $(TOP)/hw/mcu/microchip/samd/asf4/samd21/hal/utils/include \ + $(TOP)/hw/mcu/microchip/samd/asf4/samd21/hpl/pm/ \ + $(TOP)/hw/mcu/microchip/samd/asf4/samd21/hpl/port \ + $(TOP)/hw/mcu/microchip/samd/asf4/samd21/hri \ + $(TOP)/hw/mcu/microchip/samd/asf4/samd21/CMSIS/Include + +# For TinyUSB port source +VENDOR = microchip +CHIP_FAMILY = samd + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM0 + +# For flash-jlink target +JLINK_DEVICE = ATSAMD21G18 +JLINK_IF = swd + +# flash using jlink +flash: $(BUILD)/$(BOARD)-firmware.bin + dfu-util -a 0 -d 1d50:615c -D $< || dfu-util -a 0 -d 16d0:05a5 -D $< + diff --git a/hw/bsp/luna/luna.c b/hw/bsp/luna/luna.c new file mode 100644 index 000000000..fa321aa43 --- /dev/null +++ b/hw/bsp/luna/luna.c @@ -0,0 +1,144 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board.h" + +#include "sam.h" +#include "hal/include/hal_gpio.h" +#include "hal/include/hal_init.h" +#include "hri/hri_nvmctrl_d21.h" + +#include "hpl/gclk/hpl_gclk_base.h" +#include "hpl_pm_config.h" +#include "hpl/pm/hpl_pm_base.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB_Handler(void) +{ + tud_int_handler(0); +} + + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM DECLARATION +//--------------------------------------------------------------------+ +#define LED_PIN PIN_PA22 // pin PA22 +#define BUTTON_PIN PIN_PB22 // pin PB22 + +/* Referenced GCLKs, should be initialized firstly */ +#define _GCLK_INIT_1ST (1 << 0 | 1 << 1) + +/* Not referenced GCLKs, initialized last */ +#define _GCLK_INIT_LAST (~_GCLK_INIT_1ST) + +void board_init(void) +{ + // Clock init ( follow hpl_init.c ) + hri_nvmctrl_set_CTRLB_RWS_bf(NVMCTRL, 2); + + _pm_init(); + _sysctrl_init_sources(); +#if _GCLK_INIT_1ST + _gclk_init_generators_by_fref(_GCLK_INIT_1ST); +#endif + _sysctrl_init_referenced_generators(); + _gclk_init_generators_by_fref(_GCLK_INIT_LAST); + + // 1ms tick timer (samd SystemCoreClock may not correct) + SystemCoreClock = CONF_CPU_FREQUENCY; + SysTick_Config(CONF_CPU_FREQUENCY / 1000); + + // Led init + gpio_set_pin_direction(LED_PIN, GPIO_DIRECTION_OUT); + gpio_set_pin_level(LED_PIN, 0); + + // Button init + gpio_set_pin_direction(BUTTON_PIN, GPIO_DIRECTION_IN); + gpio_set_pin_pull_mode(BUTTON_PIN, GPIO_PULL_UP); + + /* USB Clock init + * The USB module requires a GCLK_USB of 48 MHz ~ 0.25% clock + * for low speed and full speed operation. */ + _pm_enable_bus_clock(PM_BUS_APBB, USB); + _pm_enable_bus_clock(PM_BUS_AHB, USB); + _gclk_enable_channel(USB_GCLK_ID, GCLK_CLKCTRL_GEN_GCLK0_Val); + + // USB Pin Init + gpio_set_pin_direction(PIN_PA24, GPIO_DIRECTION_OUT); + gpio_set_pin_level(PIN_PA24, false); + gpio_set_pin_pull_mode(PIN_PA24, GPIO_PULL_OFF); + gpio_set_pin_direction(PIN_PA25, GPIO_DIRECTION_OUT); + gpio_set_pin_level(PIN_PA25, false); + gpio_set_pin_pull_mode(PIN_PA25, GPIO_PULL_OFF); + + gpio_set_pin_function(PIN_PA24, PINMUX_PA24G_USB_DM); + gpio_set_pin_function(PIN_PA25, PINMUX_PA25G_USB_DP); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + gpio_set_pin_level(LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + // button is active low + return gpio_get_pin_level(BUTTON_PIN) ? 0 : 1; +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +#if CFG_TUSB_OS == OPT_OS_NONE + +volatile uint32_t system_ticks = 0; + +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} + +#endif diff --git a/hw/bsp/luna/samd21g18a_flash.ld b/hw/bsp/luna/samd21g18a_flash.ld new file mode 100644 index 000000000..158593036 --- /dev/null +++ b/hw/bsp/luna/samd21g18a_flash.ld @@ -0,0 +1,144 @@ +/** + * \file + * + * \brief Linker script for running in internal FLASH on the SAMD21G18A + * + * Copyright (c) 2017 Microchip Technology Inc. + * + * \asf_license_start + * + * \page License + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the "License"); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the Licence at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + * \asf_license_stop + * + */ + + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +SEARCH_DIR(.) + +/* Memory Spaces Definitions */ +MEMORY +{ + rom (rx) : ORIGIN = 0x00000000 + 4K, LENGTH = 0x00040000 - 4K + ram (rwx) : ORIGIN = 0x20000000, LENGTH = 0x00008000 +} + +/* The stack size used by the application. NOTE: you need to adjust according to your application. */ +STACK_SIZE = DEFINED(STACK_SIZE) ? STACK_SIZE : DEFINED(__stack_size__) ? __stack_size__ : 0x2000; + +/* Section Definitions */ +SECTIONS +{ + .text : + { + . = ALIGN(4); + _sfixed = .; + KEEP(*(.vectors .vectors.*)) + *(.text .text.* .gnu.linkonce.t.*) + *(.glue_7t) *(.glue_7) + *(.rodata .rodata* .gnu.linkonce.r.*) + *(.ARM.extab* .gnu.linkonce.armextab.*) + + /* Support C constructors, and C destructors in both user code + and the C library. This also provides support for C++ code. */ + . = ALIGN(4); + KEEP(*(.init)) + . = ALIGN(4); + __preinit_array_start = .; + KEEP (*(.preinit_array)) + __preinit_array_end = .; + + . = ALIGN(4); + __init_array_start = .; + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array)) + __init_array_end = .; + + . = ALIGN(4); + KEEP (*crtbegin.o(.ctors)) + KEEP (*(EXCLUDE_FILE (*crtend.o) .ctors)) + KEEP (*(SORT(.ctors.*))) + KEEP (*crtend.o(.ctors)) + + . = ALIGN(4); + KEEP(*(.fini)) + + . = ALIGN(4); + __fini_array_start = .; + KEEP (*(.fini_array)) + KEEP (*(SORT(.fini_array.*))) + __fini_array_end = .; + + KEEP (*crtbegin.o(.dtors)) + KEEP (*(EXCLUDE_FILE (*crtend.o) .dtors)) + KEEP (*(SORT(.dtors.*))) + KEEP (*crtend.o(.dtors)) + + . = ALIGN(4); + _efixed = .; /* End of text section */ + } > rom + + /* .ARM.exidx is sorted, so has to go in its own output section. */ + PROVIDE_HIDDEN (__exidx_start = .); + .ARM.exidx : + { + *(.ARM.exidx* .gnu.linkonce.armexidx.*) + } > rom + PROVIDE_HIDDEN (__exidx_end = .); + + . = ALIGN(4); + _etext = .; + + .relocate : AT (_etext) + { + . = ALIGN(4); + _srelocate = .; + *(.ramfunc .ramfunc.*); + *(.data .data.*); + . = ALIGN(4); + _erelocate = .; + } > ram + + /* .bss section which is used for uninitialized data */ + .bss (NOLOAD) : + { + . = ALIGN(4); + _sbss = . ; + _szero = .; + *(.bss .bss.*) + *(COMMON) + . = ALIGN(4); + _ebss = . ; + _ezero = .; + end = .; + } > ram + + /* stack section */ + .stack (NOLOAD): + { + . = ALIGN(8); + _sstack = .; + . = . + STACK_SIZE; + . = ALIGN(8); + _estack = .; + } > ram + + . = ALIGN(4); + _end = . ; +} -- cgit v1.3.1 From dc00f0cae10ec43c9f035938276b7000c3120ec2 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 16 Jul 2020 20:44:06 +0700 Subject: update link speed detection for nuc505 --- hw/bsp/nutiny_sdk_nuc505/board.mk | 10 ++++++++++ src/portable/nuvoton/nuc505/dcd_nuc505.c | 4 +++- 2 files changed, 13 insertions(+), 1 deletion(-) (limited to 'hw/bsp') diff --git a/hw/bsp/nutiny_sdk_nuc505/board.mk b/hw/bsp/nutiny_sdk_nuc505/board.mk index 5fb2119b8..8752ef8ea 100644 --- a/hw/bsp/nutiny_sdk_nuc505/board.mk +++ b/hw/bsp/nutiny_sdk_nuc505/board.mk @@ -46,6 +46,16 @@ FREERTOS_PORT = ARM_CM4F JLINK_DEVICE = NUC505YO13Y JLINK_IF = swd +# Note +# To be able to program the SPI flash, it need to boot with ICP mode "1011". +# However, in ICP mode, opencod cannot establish connection to the mcu. +# Therefore, there is no easy command line flash for NUC505 +# It is probably better to just use Nuvoton NuMicro ICP programming on windows to program the board +# - 1111 "SPI" (run from internal flash) +# - 1110 "USB" (mass storage emulator that accepts a .bin file) +# - 0111 "ICE-SPI" (allow external debugger access, but may not be programmable) +# - 1011 ICP mode (programmable via NuMicro ICP programming tool) + # Flash using Nuvoton's openocd fork at https://github.com/OpenNuvoton/OpenOCD-Nuvoton # Please compile and install it from github source flash: $(BUILD)/$(BOARD)-firmware.elf diff --git a/src/portable/nuvoton/nuc505/dcd_nuc505.c b/src/portable/nuvoton/nuc505/dcd_nuc505.c index e67b69ab2..a7961a687 100644 --- a/src/portable/nuvoton/nuc505/dcd_nuc505.c +++ b/src/portable/nuvoton/nuc505/dcd_nuc505.c @@ -452,7 +452,9 @@ void dcd_int_handler(uint8_t rhport) USBD->CEPINTEN = USBD_CEPINTEN_SETUPPKIEN_Msk; USBD->BUSINTEN = USBD_BUSINTEN_RSTIEN_Msk | USBD_BUSINTEN_RESUMEIEN_Msk | USBD_BUSINTEN_SUSPENDIEN_Msk | USBD_BUSINTEN_DMADONEIEN_Msk; USBD->CEPINTSTS = 0x1ffc; - dcd_event_bus_signal(0, DCD_EVENT_BUS_RESET, true); + + tusb_speed_t speed = (USBD->OPER & USBD_OPER_CURSPD_Msk) ? TUSB_SPEED_HIGH : TUSB_SPEED_FULL; + dcd_event_bus_reset(0, speed, true); } if (bus_state & USBD_BUSINTSTS_RESUMEIF_Msk) -- cgit v1.3.1 From 0407cfe16c7b9736da2ff36c69232e7c3f470864 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 23 Jul 2020 01:39:15 +0700 Subject: fix samd21 race condition with setup packet reproduced with Adafruit_TinyUSB_ArduinoCore port commit 11d669b4d2a40eb2fc5e51b2a9707a6de9d42363 and SAMD BSP 1.6.1 --- examples/make.mk | 54 ++++++++++++++++------------------ hw/bsp/feather_m0_express/board.mk | 10 +++++-- hw/bsp/feather_m4_express/board.mk | 10 +++++-- hw/bsp/itsybitsy_m0/board.mk | 10 +++++-- hw/bsp/itsybitsy_m4/board.mk | 10 +++++-- hw/bsp/metro_m0_express/board.mk | 10 +++++-- hw/bsp/metro_m4_express/board.mk | 10 +++++-- src/portable/microchip/samd/dcd_samd.c | 2 ++ 8 files changed, 76 insertions(+), 40 deletions(-) (limited to 'hw/bsp') diff --git a/examples/make.mk b/examples/make.mk index 2ea50753b..b7917987e 100644 --- a/examples/make.mk +++ b/examples/make.mk @@ -46,31 +46,32 @@ SRC_C += $(subst $(TOP)/,,$(wildcard $(TOP)/hw/bsp/$(BOARD)/*.c)) # Compiler Flags CFLAGS += \ - -fdata-sections \ - -ffunction-sections \ - -fsingle-precision-constant \ - -fno-strict-aliasing \ - -Wdouble-promotion \ - -Wstrict-prototypes \ - -Wall \ - -Wextra \ - -Werror \ - -Wfatal-errors \ - -Werror-implicit-function-declaration \ - -Wfloat-equal \ - -Wundef \ - -Wshadow \ - -Wwrite-strings \ - -Wsign-compare \ - -Wmissing-format-attribute \ - -Wunreachable-code \ - -Wcast-align - + -ggdb \ + -fdata-sections \ + -ffunction-sections \ + -fsingle-precision-constant \ + -fno-strict-aliasing \ + -Wdouble-promotion \ + -Wstrict-prototypes \ + -Wall \ + -Wextra \ + -Werror \ + -Wfatal-errors \ + -Werror-implicit-function-declaration \ + -Wfloat-equal \ + -Wundef \ + -Wshadow \ + -Wwrite-strings \ + -Wsign-compare \ + -Wmissing-format-attribute \ + -Wunreachable-code \ + -Wcast-align + # Debugging/Optimization ifeq ($(DEBUG), 1) - CFLAGS += -Og -ggdb + CFLAGS += -Og else - CFLAGS += -Os + CFLAGS += -Os endif # Log level is mapped to TUSB DEBUG option @@ -80,14 +81,11 @@ endif # Logger: default is uart, can be set to rtt or swo ifeq ($(LOGGER),rtt) - RTT_SRC = lib/SEGGER_RTT - - CFLAGS += -DLOGGER_RTT -DSEGGER_RTT_MODE_DEFAULT=SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL + RTT_SRC = lib/SEGGER_RTT + CFLAGS += -DLOGGER_RTT -DSEGGER_RTT_MODE_DEFAULT=SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL INC += $(TOP)/$(RTT_SRC)/RTT SRC_C += $(RTT_SRC)/RTT/SEGGER_RTT_printf.c SRC_C += $(RTT_SRC)/RTT/SEGGER_RTT.c - else ifeq ($(LOGGER),swo) - CFLAGS += -DLOGGER_SWO - + CFLAGS += -DLOGGER_SWO endif diff --git a/hw/bsp/feather_m0_express/board.mk b/hw/bsp/feather_m0_express/board.mk index d762c4eca..7b6891e03 100644 --- a/hw/bsp/feather_m0_express/board.mk +++ b/hw/bsp/feather_m0_express/board.mk @@ -41,5 +41,11 @@ FREERTOS_PORT = ARM_CM0 JLINK_DEVICE = ATSAMD21G18 JLINK_IF = swd -# flash using jlink -flash: flash-jlink +# flash using bossac at least version 1.8 +# can be found in arduino15/packages/arduino/tools/bossac/ +# Add it to your PATH or change BOSSAC variable to match your installation +BOSSAC = bossac + +flash: $(BUILD)/$(BOARD)-firmware.bin + @:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyACM0) + $(BOSSAC) --port=$(SERIAL) -U -i --offset=0x2000 -e -w $^ -R diff --git a/hw/bsp/feather_m4_express/board.mk b/hw/bsp/feather_m4_express/board.mk index 49c2d7f2f..34c98597c 100644 --- a/hw/bsp/feather_m4_express/board.mk +++ b/hw/bsp/feather_m4_express/board.mk @@ -44,5 +44,11 @@ FREERTOS_PORT = ARM_CM4F JLINK_DEVICE = ATSAMD51J19 JLINK_IF = swd -# flash using jlink -flash: flash-jlink +# flash using bossac at least version 1.8 +# can be found in arduino15/packages/arduino/tools/bossac/ +# Add it to your PATH or change BOSSAC variable to match your installation +BOSSAC = bossac + +flash: $(BUILD)/$(BOARD)-firmware.bin + @:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyACM0) + $(BOSSAC) --port=$(SERIAL) -U -i --offset=0x4000 -e -w $^ -R diff --git a/hw/bsp/itsybitsy_m0/board.mk b/hw/bsp/itsybitsy_m0/board.mk index d762c4eca..7b6891e03 100644 --- a/hw/bsp/itsybitsy_m0/board.mk +++ b/hw/bsp/itsybitsy_m0/board.mk @@ -41,5 +41,11 @@ FREERTOS_PORT = ARM_CM0 JLINK_DEVICE = ATSAMD21G18 JLINK_IF = swd -# flash using jlink -flash: flash-jlink +# flash using bossac at least version 1.8 +# can be found in arduino15/packages/arduino/tools/bossac/ +# Add it to your PATH or change BOSSAC variable to match your installation +BOSSAC = bossac + +flash: $(BUILD)/$(BOARD)-firmware.bin + @:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyACM0) + $(BOSSAC) --port=$(SERIAL) -U -i --offset=0x2000 -e -w $^ -R diff --git a/hw/bsp/itsybitsy_m4/board.mk b/hw/bsp/itsybitsy_m4/board.mk index 49c2d7f2f..34c98597c 100644 --- a/hw/bsp/itsybitsy_m4/board.mk +++ b/hw/bsp/itsybitsy_m4/board.mk @@ -44,5 +44,11 @@ FREERTOS_PORT = ARM_CM4F JLINK_DEVICE = ATSAMD51J19 JLINK_IF = swd -# flash using jlink -flash: flash-jlink +# flash using bossac at least version 1.8 +# can be found in arduino15/packages/arduino/tools/bossac/ +# Add it to your PATH or change BOSSAC variable to match your installation +BOSSAC = bossac + +flash: $(BUILD)/$(BOARD)-firmware.bin + @:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyACM0) + $(BOSSAC) --port=$(SERIAL) -U -i --offset=0x4000 -e -w $^ -R diff --git a/hw/bsp/metro_m0_express/board.mk b/hw/bsp/metro_m0_express/board.mk index d762c4eca..7b6891e03 100644 --- a/hw/bsp/metro_m0_express/board.mk +++ b/hw/bsp/metro_m0_express/board.mk @@ -41,5 +41,11 @@ FREERTOS_PORT = ARM_CM0 JLINK_DEVICE = ATSAMD21G18 JLINK_IF = swd -# flash using jlink -flash: flash-jlink +# flash using bossac at least version 1.8 +# can be found in arduino15/packages/arduino/tools/bossac/ +# Add it to your PATH or change BOSSAC variable to match your installation +BOSSAC = bossac + +flash: $(BUILD)/$(BOARD)-firmware.bin + @:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyACM0) + $(BOSSAC) --port=$(SERIAL) -U -i --offset=0x2000 -e -w $^ -R diff --git a/hw/bsp/metro_m4_express/board.mk b/hw/bsp/metro_m4_express/board.mk index 49c2d7f2f..34c98597c 100644 --- a/hw/bsp/metro_m4_express/board.mk +++ b/hw/bsp/metro_m4_express/board.mk @@ -44,5 +44,11 @@ FREERTOS_PORT = ARM_CM4F JLINK_DEVICE = ATSAMD51J19 JLINK_IF = swd -# flash using jlink -flash: flash-jlink +# flash using bossac at least version 1.8 +# can be found in arduino15/packages/arduino/tools/bossac/ +# Add it to your PATH or change BOSSAC variable to match your installation +BOSSAC = bossac + +flash: $(BUILD)/$(BOARD)-firmware.bin + @:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyACM0) + $(BOSSAC) --port=$(SERIAL) -U -i --offset=0x4000 -e -w $^ -R diff --git a/src/portable/microchip/samd/dcd_samd.c b/src/portable/microchip/samd/dcd_samd.c index 45bff2511..d0cc8560a 100644 --- a/src/portable/microchip/samd/dcd_samd.c +++ b/src/portable/microchip/samd/dcd_samd.c @@ -43,6 +43,8 @@ static inline void prepare_setup(void) { // Only make sure the EP0 OUT buffer is ready sram_registers[0][0].ADDR.reg = (uint32_t) _setup_packet; + sram_registers[0][0].PCKSIZE.bit.MULTI_PACKET_SIZE = sizeof(_setup_packet); + sram_registers[0][0].PCKSIZE.bit.BYTE_COUNT = 0; } // Setup the control endpoint 0. -- cgit v1.3.1 From 76fe8ac61222856efd791fe5d20e89b3ffced71b Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 21 Aug 2020 12:19:38 +0700 Subject: fix samg55 ci build --- hw/bsp/samg55xplained/board.mk | 4 ++-- hw/mcu/microchip | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) (limited to 'hw/bsp') diff --git a/hw/bsp/samg55xplained/board.mk b/hw/bsp/samg55xplained/board.mk index e0c24ed9c..b53757dff 100644 --- a/hw/bsp/samg55xplained/board.mk +++ b/hw/bsp/samg55xplained/board.mk @@ -18,8 +18,8 @@ ASF_DIR = hw/mcu/microchip/samg55 LD_FILE = hw/bsp/$(BOARD)/samg55j19_flash.ld SRC_C += \ - $(ASF_DIR)/samg55/gcc/gcc/startup_samg55j19.c \ - $(ASF_DIR)/samg55/gcc/system_samg55j19.c \ + $(ASF_DIR)/samg55/gcc/gcc/startup_samg55.c \ + $(ASF_DIR)/samg55/gcc/system_samg55.c \ $(ASF_DIR)/hpl/core/hpl_init.c \ $(ASF_DIR)/hpl/usart/hpl_usart.c \ $(ASF_DIR)/hpl/pmc/hpl_pmc.c \ diff --git a/hw/mcu/microchip b/hw/mcu/microchip index 66b5a1199..168322aa7 160000 --- a/hw/mcu/microchip +++ b/hw/mcu/microchip @@ -1 +1 @@ -Subproject commit 66b5a11995025426224e0ba6f377322e6e8893b6 +Subproject commit 168322aa7100f60d6837505f5705fd61454dac27 -- cgit v1.3.1 From 91f7ce9769f9cacf4f7e86dfd72b2a93ad2f4bfb Mon Sep 17 00:00:00 2001 From: Katherine Temkin Date: Thu, 20 Aug 2020 21:49:35 -0600 Subject: add support for SAMD11 devices / add samd11_xplained board --- README.md | 2 +- docs/boards.md | 1 + hw/bsp/samd11_xplained/board.mk | 53 ++++++++++ hw/bsp/samd11_xplained/samd11_xplained.c | 152 ++++++++++++++++++++++++++++ hw/bsp/samd11_xplained/samd11d14am_flash.ld | 143 ++++++++++++++++++++++++++ 5 files changed, 350 insertions(+), 1 deletion(-) create mode 100644 hw/bsp/samd11_xplained/board.mk create mode 100644 hw/bsp/samd11_xplained/samd11_xplained.c create mode 100644 hw/bsp/samd11_xplained/samd11d14am_flash.ld (limited to 'hw/bsp') diff --git a/README.md b/README.md index 260248eda..6ca41e0f0 100644 --- a/README.md +++ b/README.md @@ -32,7 +32,7 @@ The stack supports the following MCUs: - **Espressif:** ESP32-S2 - **Dialog:** DA1469x -- **MicroChip:** SAMD21, SAMD51, SAME5x (device only) +- **MicroChip:** SAMD11, SAMD21, SAMD51, SAME5x (device only) - **NordicSemi:** nRF52833, nRF52840 - **Nuvoton:** NUC120, NUC121/NUC125, NUC126, NUC505 - **NXP:** diff --git a/docs/boards.md b/docs/boards.md index 53dc95397..381d124cc 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -28,6 +28,7 @@ This code base already had supported for a handful of following boards (sorted a - [Adafruit ItsyBitsy M4 Express](https://www.adafruit.com/product/3800) - [Adafruit Metro M0 Express](https://www.adafruit.com/product/3505) - [Adafruit Metro M4 Express](https://www.adafruit.com/product/3382) +- [Microchip SAMD11 Xplained](https://www.microchip.com/developmenttools/ProductDetails/atsamd11-xpro) - [Seeeduino Xiao](https://www.seeedstudio.com/Seeeduino-XIAO-Arduino-Microcontroller-SAMD21-Cortex-M0+-p-4426.html) - [Great Scott Gadgets LUNA](https://greatscottgadgets.com/luna/) diff --git a/hw/bsp/samd11_xplained/board.mk b/hw/bsp/samd11_xplained/board.mk new file mode 100644 index 000000000..db0c62cf1 --- /dev/null +++ b/hw/bsp/samd11_xplained/board.mk @@ -0,0 +1,53 @@ +CFLAGS += \ + -ffunction-sections \ + -fdata-sections \ + -Wl,--gc-sections \ + -mthumb \ + -mabi=aapcs-linux \ + -mcpu=cortex-m0plus \ + -nostdlib -nostartfiles \ + -D__SAMD11D14AM__ \ + -DCONF_DFLL_OVERWRITE_CALIBRATION=0 \ + -DOSC32K_OVERWRITE_CALIBRATION=0 \ + -DCFG_TUSB_MCU=OPT_MCU_SAMD21 \ + -fshort-enums \ + -Os + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/samd11d14am_flash.ld + +SRC_C += \ + hw/mcu/microchip/samd11/gcc/gcc/startup_samd11.c \ + hw/mcu/microchip/samd11/gcc/system_samd11.c \ + hw/mcu/microchip/samd11/hpl/gclk/hpl_gclk.c \ + hw/mcu/microchip/samd11/hpl/pm/hpl_pm.c \ + hw/mcu/microchip/samd11/hpl/sysctrl/hpl_sysctrl.c \ + hw/mcu/microchip/samd11/hal/src/hal_atomic.c + +INC += \ + $(TOP)/hw/mcu/microchip/samd11/ \ + $(TOP)/hw/mcu/microchip/samd11/config \ + $(TOP)/hw/mcu/microchip/samd11/include \ + $(TOP)/hw/mcu/microchip/samd11/hal/include \ + $(TOP)/hw/mcu/microchip/samd11/hal/utils/include \ + $(TOP)/hw/mcu/microchip/samd11/hpl/pm/ \ + $(TOP)/hw/mcu/microchip/samd11/hpl/port \ + $(TOP)/hw/mcu/microchip/samd11/hri \ + $(TOP)/hw/mcu/microchip/samd11/CMSIS/Include \ + $(TOP)/hw/mcu/microchip/samd11/CMSIS/Core/Include + +# For TinyUSB port source +VENDOR = microchip +CHIP_FAMILY = samd + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM0 + +# For flash-jlink target +JLINK_DEVICE = ATSAMD11D14 +JLINK_IF = swd + +# flash using edbg +flash: $(BUILD)/$(BOARD)-firmware.bin + edbg -b -t samd11 -e -pv -f $< + diff --git a/hw/bsp/samd11_xplained/samd11_xplained.c b/hw/bsp/samd11_xplained/samd11_xplained.c new file mode 100644 index 000000000..874e36d7c --- /dev/null +++ b/hw/bsp/samd11_xplained/samd11_xplained.c @@ -0,0 +1,152 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board.h" + +#include "sam.h" +#include "hal/include/hal_gpio.h" +#include "hal/include/hal_init.h" +#include "hri/hri_nvmctrl_d11.h" + +#include "hpl/gclk/hpl_gclk_base.h" +#include "hpl_pm_config.h" +#include "hpl/pm/hpl_pm_base.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB_Handler(void) +{ + tud_int_handler(0); +} + + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM DECLARATION +//--------------------------------------------------------------------+ +#define LED_PIN PIN_PA16 // pin PA22 +#define BUTTON_PIN PIN_PA14 // pin PB22 + +/* Referenced GCLKs, should be initialized firstly */ +#define _GCLK_INIT_1ST (1 << 0 | 1 << 1) + +/* Not referenced GCLKs, initialized last */ +#define _GCLK_INIT_LAST (~_GCLK_INIT_1ST) + +void board_init(void) +{ + // Clock init ( follow hpl_init.c ) + hri_nvmctrl_set_CTRLB_RWS_bf(NVMCTRL, 2); + + _pm_init(); + _sysctrl_init_sources(); +#if _GCLK_INIT_1ST + _gclk_init_generators_by_fref(_GCLK_INIT_1ST); +#endif + _sysctrl_init_referenced_generators(); + _gclk_init_generators_by_fref(_GCLK_INIT_LAST); + + // 1ms tick timer (samd SystemCoreClock may not correct) + SystemCoreClock = CONF_CPU_FREQUENCY; + SysTick_Config(CONF_CPU_FREQUENCY / 1000); + + // Led init + gpio_set_pin_direction(LED_PIN, GPIO_DIRECTION_OUT); + gpio_set_pin_level(LED_PIN, 0); + + // Button init + gpio_set_pin_direction(BUTTON_PIN, GPIO_DIRECTION_IN); + gpio_set_pin_pull_mode(BUTTON_PIN, GPIO_PULL_UP); + + /* USB Clock init + * The USB module requires a GCLK_USB of 48 MHz ~ 0.25% clock + * for low speed and full speed operation. */ + _pm_enable_bus_clock(PM_BUS_APBB, USB); + _pm_enable_bus_clock(PM_BUS_AHB, USB); + _gclk_enable_channel(USB_GCLK_ID, GCLK_CLKCTRL_GEN_GCLK0_Val); + + // USB Pin Init + gpio_set_pin_direction(PIN_PA24, GPIO_DIRECTION_OUT); + gpio_set_pin_level(PIN_PA24, false); + gpio_set_pin_pull_mode(PIN_PA24, GPIO_PULL_OFF); + gpio_set_pin_direction(PIN_PA25, GPIO_DIRECTION_OUT); + gpio_set_pin_level(PIN_PA25, false); + gpio_set_pin_pull_mode(PIN_PA25, GPIO_PULL_OFF); + + gpio_set_pin_function(PIN_PA24, PINMUX_PA24G_USB_DM); + gpio_set_pin_function(PIN_PA25, PINMUX_PA25G_USB_DP); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + gpio_set_pin_level(LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + // button is active low + return gpio_get_pin_level(BUTTON_PIN) ? 0 : 1; +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +#if CFG_TUSB_OS == OPT_OS_NONE + +volatile uint32_t system_ticks = 0; + +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} + +void _init(void) +{ + // This _init() standin makes certain GCC environments happier. + // They expect the main binary to have a constructor called _init; but don't provide a weak default. + // Providing an empty constructor satisfies this odd case, and doesn't harm anything. +} + + +#endif diff --git a/hw/bsp/samd11_xplained/samd11d14am_flash.ld b/hw/bsp/samd11_xplained/samd11d14am_flash.ld new file mode 100644 index 000000000..2153f5f50 --- /dev/null +++ b/hw/bsp/samd11_xplained/samd11d14am_flash.ld @@ -0,0 +1,143 @@ +/** + * \file + * + * \brief Linker script for running in internal FLASH on the SAMD11D14AM + * + * Copyright (c) 2018 Microchip Technology Inc. + * + * \asf_license_start + * + * \page License + * + * SPDX-License-Identifier: Apache-2.0 + * + * Licensed under the Apache License, Version 2.0 (the "License"); you may + * not use this file except in compliance with the License. + * You may obtain a copy of the Licence at + * + * http://www.apache.org/licenses/LICENSE-2.0 + * + * Unless required by applicable law or agreed to in writing, software + * distributed under the License is distributed on an AS IS BASIS, WITHOUT + * WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + * See the License for the specific language governing permissions and + * limitations under the License. + * + * \asf_license_stop + * + */ + + +OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") +OUTPUT_ARCH(arm) +SEARCH_DIR(.) + +/* Memory Spaces Definitions */ +MEMORY +{ + rom (rx) : ORIGIN = 0x00000000, LENGTH = 0x00004000 + ram (rwx) : ORIGIN = 0x20000000, LENGTH = 0x00001000 +} + +/* The stack size used by the application. NOTE: you need to adjust according to your application. */ +STACK_SIZE = DEFINED(STACK_SIZE) ? STACK_SIZE : DEFINED(__stack_size__) ? __stack_size__ : 0x400; + +/* Section Definitions */ +SECTIONS +{ + .text : + { + . = ALIGN(4); + _sfixed = .; + KEEP(*(.vectors .vectors.*)) + *(.text .text.* .gnu.linkonce.t.*) + *(.glue_7t) *(.glue_7) + *(.rodata .rodata* .gnu.linkonce.r.*) + *(.ARM.extab* .gnu.linkonce.armextab.*) + + /* Support C constructors, and C destructors in both user code + and the C library. This also provides support for C++ code. */ + . = ALIGN(4); + KEEP(*(.init)) + . = ALIGN(4); + __preinit_array_start = .; + KEEP (*(.preinit_array)) + __preinit_array_end = .; + + . = ALIGN(4); + __init_array_start = .; + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array)) + __init_array_end = .; + + . = ALIGN(4); + KEEP (*crtbegin.o(.ctors)) + KEEP (*(EXCLUDE_FILE (*crtend.o) .ctors)) + KEEP (*(SORT(.ctors.*))) + KEEP (*crtend.o(.ctors)) + + . = ALIGN(4); + KEEP(*(.fini)) + + . = ALIGN(4); + __fini_array_start = .; + KEEP (*(.fini_array)) + KEEP (*(SORT(.fini_array.*))) + __fini_array_end = .; + + KEEP (*crtbegin.o(.dtors)) + KEEP (*(EXCLUDE_FILE (*crtend.o) .dtors)) + KEEP (*(SORT(.dtors.*))) + KEEP (*crtend.o(.dtors)) + + . = ALIGN(4); + _efixed = .; /* End of text section */ + } > rom + + /* .ARM.exidx is sorted, so has to go in its own output section. */ + PROVIDE_HIDDEN (__exidx_start = .); + .ARM.exidx : + { + *(.ARM.exidx* .gnu.linkonce.armexidx.*) + } > rom + PROVIDE_HIDDEN (__exidx_end = .); + + . = ALIGN(4); + _etext = .; + + .relocate : AT (_etext) + { + . = ALIGN(4); + _srelocate = .; + *(.ramfunc .ramfunc.*); + *(.data .data.*); + . = ALIGN(4); + _erelocate = .; + } > ram + + /* .bss section which is used for uninitialized data */ + .bss (NOLOAD) : + { + . = ALIGN(4); + _sbss = . ; + _szero = .; + *(.bss .bss.*) + *(COMMON) + . = ALIGN(4); + _ebss = . ; + _ezero = .; + } > ram + + /* stack section */ + .stack (NOLOAD): + { + . = ALIGN(8); + _sstack = .; + . = . + STACK_SIZE; + . = ALIGN(8); + _estack = .; + } > ram + + . = ALIGN(4); + _end = . ; +} -- cgit v1.3.1 From 9d3a9cf546580907d0e72fd6e36e23050bcab850 Mon Sep 17 00:00:00 2001 From: hathach Date: Sat, 22 Aug 2020 18:46:19 +0700 Subject: add OPT_MCU_SAMD11 skip ci build for example that need more ROM/RAM could fit into SAMD11 --- examples/device/cdc_msc/.skip.MCU_SAMD11 | 0 examples/device/cdc_msc_freertos/.skip.MCU_SAMD11 | 0 examples/device/dynamic_configuration/.skip.MCU_SAMD11 | 0 examples/device/hid_composite_freertos/.skip.MCU_SAMD11 | 0 examples/device/msc_dual_lun/.skip.MCU_SAMD11 | 0 examples/device/net_lwip_webserver/.skip.MCU_SAMD11 | 0 hw/bsp/board_mcu.h | 2 +- hw/bsp/samd11_xplained/board.mk | 2 +- src/portable/microchip/samd/dcd_samd.c | 5 +++-- src/tusb_option.h | 3 ++- 10 files changed, 7 insertions(+), 5 deletions(-) create mode 100644 examples/device/cdc_msc/.skip.MCU_SAMD11 create mode 100644 examples/device/cdc_msc_freertos/.skip.MCU_SAMD11 create mode 100644 examples/device/dynamic_configuration/.skip.MCU_SAMD11 create mode 100644 examples/device/hid_composite_freertos/.skip.MCU_SAMD11 create mode 100644 examples/device/msc_dual_lun/.skip.MCU_SAMD11 create mode 100644 examples/device/net_lwip_webserver/.skip.MCU_SAMD11 (limited to 'hw/bsp') diff --git a/examples/device/cdc_msc/.skip.MCU_SAMD11 b/examples/device/cdc_msc/.skip.MCU_SAMD11 new file mode 100644 index 000000000..e69de29bb diff --git a/examples/device/cdc_msc_freertos/.skip.MCU_SAMD11 b/examples/device/cdc_msc_freertos/.skip.MCU_SAMD11 new file mode 100644 index 000000000..e69de29bb diff --git a/examples/device/dynamic_configuration/.skip.MCU_SAMD11 b/examples/device/dynamic_configuration/.skip.MCU_SAMD11 new file mode 100644 index 000000000..e69de29bb diff --git a/examples/device/hid_composite_freertos/.skip.MCU_SAMD11 b/examples/device/hid_composite_freertos/.skip.MCU_SAMD11 new file mode 100644 index 000000000..e69de29bb diff --git a/examples/device/msc_dual_lun/.skip.MCU_SAMD11 b/examples/device/msc_dual_lun/.skip.MCU_SAMD11 new file mode 100644 index 000000000..e69de29bb diff --git a/examples/device/net_lwip_webserver/.skip.MCU_SAMD11 b/examples/device/net_lwip_webserver/.skip.MCU_SAMD11 new file mode 100644 index 000000000..e69de29bb diff --git a/hw/bsp/board_mcu.h b/hw/bsp/board_mcu.h index 15b31edfd..3382d465d 100644 --- a/hw/bsp/board_mcu.h +++ b/hw/bsp/board_mcu.h @@ -52,7 +52,7 @@ #elif CFG_TUSB_MCU == OPT_MCU_NRF5X #include "nrf.h" -#elif CFG_TUSB_MCU == OPT_MCU_SAMD21 || CFG_TUSB_MCU == OPT_MCU_SAMD51 +#elif CFG_TUSB_MCU == OPT_MCU_SAMD11 || CFG_TUSB_MCU == OPT_MCU_SAMD21 || CFG_TUSB_MCU == OPT_MCU_SAMD51 #include "sam.h" #elif CFG_TUSB_MCU == OPT_MCU_SAMG diff --git a/hw/bsp/samd11_xplained/board.mk b/hw/bsp/samd11_xplained/board.mk index db0c62cf1..5b1a42157 100644 --- a/hw/bsp/samd11_xplained/board.mk +++ b/hw/bsp/samd11_xplained/board.mk @@ -9,7 +9,7 @@ CFLAGS += \ -D__SAMD11D14AM__ \ -DCONF_DFLL_OVERWRITE_CALIBRATION=0 \ -DOSC32K_OVERWRITE_CALIBRATION=0 \ - -DCFG_TUSB_MCU=OPT_MCU_SAMD21 \ + -DCFG_TUSB_MCU=OPT_MCU_SAMD11 \ -fshort-enums \ -Os diff --git a/src/portable/microchip/samd/dcd_samd.c b/src/portable/microchip/samd/dcd_samd.c index d0cc8560a..f1dca88a5 100644 --- a/src/portable/microchip/samd/dcd_samd.c +++ b/src/portable/microchip/samd/dcd_samd.c @@ -27,7 +27,8 @@ #include "tusb_option.h" #if TUSB_OPT_DEVICE_ENABLED && \ - (CFG_TUSB_MCU == OPT_MCU_SAMD21 || CFG_TUSB_MCU == OPT_MCU_SAMD51 || CFG_TUSB_MCU == OPT_MCU_SAME5X) + (CFG_TUSB_MCU == OPT_MCU_SAMD11 || CFG_TUSB_MCU == OPT_MCU_SAMD21 || \ + CFG_TUSB_MCU == OPT_MCU_SAMD51 || CFG_TUSB_MCU == OPT_MCU_SAME5X) #include "sam.h" #include "device/dcd.h" @@ -113,7 +114,7 @@ void dcd_int_disable(uint8_t rhport) NVIC_DisableIRQ(USB_0_IRQn); } -#elif CFG_TUSB_MCU == OPT_MCU_SAMD21 +#elif CFG_TUSB_MCU == OPT_MCU_SAMD11 || CFG_TUSB_MCU == OPT_MCU_SAMD21 void dcd_int_enable(uint8_t rhport) { diff --git a/src/tusb_option.h b/src/tusb_option.h index abf6450ca..7e486bff0 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -55,10 +55,11 @@ #define OPT_MCU_NRF5X 100 ///< Nordic nRF5x series // SAM +#define OPT_MCU_SAMD11 204 ///< MicroChip SAMD11 #define OPT_MCU_SAMD21 200 ///< MicroChip SAMD21 #define OPT_MCU_SAMD51 201 ///< MicroChip SAMD51 -#define OPT_MCU_SAMG 202 ///< MicroChip SAMDG series #define OPT_MCU_SAME5X 203 ///< MicroChip SAM E5x +#define OPT_MCU_SAMG 202 ///< MicroChip SAMDG series // STM32 #define OPT_MCU_STM32F0 300 ///< ST STM32F0 -- cgit v1.3.1 From 7a443d6beafd0b5f3a9ef8cfdcdfb68bfece1170 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 27 Aug 2020 16:40:24 +0700 Subject: add itsybitsy nrf52840 board support --- docs/boards.md | 1 + hw/bsp/itsybitsy_nrf52840/board.mk | 64 +++++++ hw/bsp/itsybitsy_nrf52840/itsybitsy_nrf52840.c | 225 +++++++++++++++++++++++++ hw/bsp/itsybitsy_nrf52840/nrf52840_s140_v6.ld | 38 +++++ 4 files changed, 328 insertions(+) create mode 100644 hw/bsp/itsybitsy_nrf52840/board.mk create mode 100644 hw/bsp/itsybitsy_nrf52840/itsybitsy_nrf52840.c create mode 100644 hw/bsp/itsybitsy_nrf52840/nrf52840_s140_v6.ld (limited to 'hw/bsp') diff --git a/docs/boards.md b/docs/boards.md index 381d124cc..1b3de29e9 100644 --- a/docs/boards.md +++ b/docs/boards.md @@ -38,6 +38,7 @@ This code base already had supported for a handful of following boards (sorted a - [Adafruit CLUE](https://www.adafruit.com/product/4500) - [Adafruit Feather nRF52840 Express](https://www.adafruit.com/product/4062) - [Adafruit Feather nRF52840 Sense](https://www.adafruit.com/product/4516) +- [Adafruit ItsyBitsy nRF52840 Express](https://www.adafruit.com/product/4481) - [Arduino Nano 33 BLE](https://store.arduino.cc/usa/nano-33-ble) - [Arduino Nano 33 BLE Sense](https://store.arduino.cc/usa/nano-33-ble-sense) - [Maker Diary nRF52840 MDK Dongle](https://wiki.makerdiary.com/nrf52840-mdk-usb-dongle) diff --git a/hw/bsp/itsybitsy_nrf52840/board.mk b/hw/bsp/itsybitsy_nrf52840/board.mk new file mode 100644 index 000000000..7b2625cd4 --- /dev/null +++ b/hw/bsp/itsybitsy_nrf52840/board.mk @@ -0,0 +1,64 @@ +CFLAGS += \ + -flto \ + -mthumb \ + -mabi=aapcs \ + -mcpu=cortex-m4 \ + -mfloat-abi=hard \ + -mfpu=fpv4-sp-d16 \ + -DCFG_TUSB_MCU=OPT_MCU_NRF5X \ + -DNRF52840_XXAA \ + -DCONFIG_GPIO_AS_PINRESET + +# suppress warning caused by vendor mcu driver +CFLAGS += -Wno-error=undef -Wno-error=unused-parameter -Wno-error=cast-align + +# due to tusb_hal_nrf_power_event +GCCVERSION = $(firstword $(subst ., ,$(shell arm-none-eabi-gcc -dumpversion))) +ifeq ($(shell expr $(GCCVERSION) \>= 8), 1) +CFLAGS += -Wno-error=cast-function-type +endif + +# All source paths should be relative to the top level. +LD_FILE = hw/bsp/$(BOARD)/nrf52840_s140_v6.ld + +LDFLAGS += -L$(TOP)/hw/mcu/nordic/nrfx/mdk + +SRC_C += \ + hw/mcu/nordic/nrfx/drivers/src/nrfx_power.c \ + hw/mcu/nordic/nrfx/drivers/src/nrfx_uarte.c \ + hw/mcu/nordic/nrfx/mdk/system_nrf52840.c + +INC += \ + $(TOP)/lib/CMSIS_4/CMSIS/Include \ + $(TOP)/hw/mcu/nordic \ + $(TOP)/hw/mcu/nordic/nrfx \ + $(TOP)/hw/mcu/nordic/nrfx/mdk \ + $(TOP)/hw/mcu/nordic/nrfx/hal \ + $(TOP)/hw/mcu/nordic/nrfx/drivers/include \ + $(TOP)/hw/mcu/nordic/nrfx/drivers/src \ + +SRC_S += hw/mcu/nordic/nrfx/mdk/gcc_startup_nrf52840.S + +ASFLAGS += -D__HEAP_SIZE=0 + +# For TinyUSB port source +VENDOR = nordic +CHIP_FAMILY = nrf5x + +# For freeRTOS port source +FREERTOS_PORT = ARM_CM4F + +# For flash-jlink target +JLINK_DEVICE = nRF52840_xxAA +JLINK_IF = swd + +# For uf2 conversion +UF2_FAMILY = 0xADA52840 + +$(BUILD)/$(BOARD)-firmware.zip: $(BUILD)/$(BOARD)-firmware.hex + adafruit-nrfutil dfu genpkg --dev-type 0x0052 --sd-req 0xFFFE --application $^ $@ + +# flash using adafruit-nrfutil dfu +flash: $(BUILD)/$(BOARD)-firmware.zip + @:$(call check_defined, SERIAL, example: SERIAL=/dev/ttyACM0) + adafruit-nrfutil --verbose dfu serial --package $^ -p $(SERIAL) -b 115200 --singlebank --touch 1200 diff --git a/hw/bsp/itsybitsy_nrf52840/itsybitsy_nrf52840.c b/hw/bsp/itsybitsy_nrf52840/itsybitsy_nrf52840.c new file mode 100644 index 000000000..e9e5a3876 --- /dev/null +++ b/hw/bsp/itsybitsy_nrf52840/itsybitsy_nrf52840.c @@ -0,0 +1,225 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board.h" + +#include "nrfx.h" +#include "nrfx/hal/nrf_gpio.h" +#include "nrfx/drivers/include/nrfx_power.h" +#include "nrfx/drivers/include/nrfx_uarte.h" + +#ifdef SOFTDEVICE_PRESENT +#include "nrf_sdm.h" +#include "nrf_soc.h" +#endif + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USBD_IRQHandler(void) +{ + tud_int_handler(0); +} + +/*------------------------------------------------------------------*/ +/* MACRO TYPEDEF CONSTANT ENUM + *------------------------------------------------------------------*/ +#define _PINNUM(port, pin) ((port)*32 + (pin)) + +#define LED_PIN _PINNUM(0, 6) +#define LED_STATE_ON 1 + +#define BUTTON_PIN _PINNUM(0, 29) + +#define UART_RX_PIN 25 +#define UART_TX_PIN 24 + +static nrfx_uarte_t _uart_id = NRFX_UARTE_INSTANCE(0); + +// tinyusb function that handles power event (detected, ready, removed) +// We must call it within SD's SOC event handler, or set it as power event handler if SD is not enabled. +extern void tusb_hal_nrf_power_event(uint32_t event); + +void board_init(void) +{ + // stop LF clock just in case we jump from application without reset + NRF_CLOCK->TASKS_LFCLKSTOP = 1UL; + + // Config clock source: XTAL or RC in sdk_config.h + NRF_CLOCK->LFCLKSRC = (uint32_t)((CLOCK_LFCLKSRC_SRC_Xtal << CLOCK_LFCLKSRC_SRC_Pos) & CLOCK_LFCLKSRC_SRC_Msk); + NRF_CLOCK->TASKS_LFCLKSTART = 1UL; + + // LED + nrf_gpio_cfg_output(LED_PIN); + board_led_write(false); + + // Button + nrf_gpio_cfg_input(BUTTON_PIN, NRF_GPIO_PIN_PULLUP); + + // 1ms tick timer + SysTick_Config(SystemCoreClock/1000); + + // UART + nrfx_uarte_config_t uart_cfg = + { + .pseltxd = UART_TX_PIN, + .pselrxd = UART_RX_PIN, + .pselcts = NRF_UARTE_PSEL_DISCONNECTED, + .pselrts = NRF_UARTE_PSEL_DISCONNECTED, + .p_context = NULL, + .baudrate = NRF_UARTE_BAUDRATE_115200, // CFG_BOARD_UART_BAUDRATE + .interrupt_priority = 7, + .hal_cfg = { + .hwfc = NRF_UARTE_HWFC_DISABLED, + .parity = NRF_UARTE_PARITY_EXCLUDED, + } + }; + + nrfx_uarte_init(&_uart_id, &uart_cfg, NULL); //uart_handler); + + //------------- USB -------------// +#if TUSB_OPT_DEVICE_ENABLED + // Priorities 0, 1, 4 (nRF52) are reserved for SoftDevice + // 2 is highest for application + NVIC_SetPriority(USBD_IRQn, 2); + + // USB power may already be ready at this time -> no event generated + // We need to invoke the handler based on the status initially + uint32_t usb_reg; + +#ifdef SOFTDEVICE_PRESENT + uint8_t sd_en = false; + sd_softdevice_is_enabled(&sd_en); + + if ( sd_en ) { + sd_power_usbdetected_enable(true); + sd_power_usbpwrrdy_enable(true); + sd_power_usbremoved_enable(true); + + sd_power_usbregstatus_get(&usb_reg); + }else +#endif + { + // Power module init + const nrfx_power_config_t pwr_cfg = { 0 }; + nrfx_power_init(&pwr_cfg); + + // Register tusb function as USB power handler + const nrfx_power_usbevt_config_t config = { .handler = (nrfx_power_usb_event_handler_t) tusb_hal_nrf_power_event }; + nrfx_power_usbevt_init(&config); + + nrfx_power_usbevt_enable(); + + usb_reg = NRF_POWER->USBREGSTATUS; + } + + if ( usb_reg & POWER_USBREGSTATUS_VBUSDETECT_Msk ) tusb_hal_nrf_power_event(NRFX_POWER_USB_EVT_DETECTED); + if ( usb_reg & POWER_USBREGSTATUS_OUTPUTRDY_Msk ) tusb_hal_nrf_power_event(NRFX_POWER_USB_EVT_READY); +#endif +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + nrf_gpio_pin_write(LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +} + +uint32_t board_button_read(void) +{ + // button is active LOW + return (nrf_gpio_pin_read(BUTTON_PIN) ? 0 : 1); +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +// return NRFX_SUCCESS == nrfx_uart_rx(&_uart_id, buf, (size_t) len) ? len : 0; +} + +int board_uart_write(void const * buf, int len) +{ + return (NRFX_SUCCESS == nrfx_uarte_tx(&_uart_id, (uint8_t const*) buf, (size_t) len)) ? len : 0; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler (void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +#ifdef SOFTDEVICE_PRESENT +// process SOC event from SD +uint32_t proc_soc(void) +{ + uint32_t soc_evt; + uint32_t err = sd_evt_get(&soc_evt); + + if (NRF_SUCCESS == err) + { + /*------------- usb power event handler -------------*/ + int32_t usbevt = (soc_evt == NRF_EVT_POWER_USB_DETECTED ) ? NRFX_POWER_USB_EVT_DETECTED: + (soc_evt == NRF_EVT_POWER_USB_POWER_READY) ? NRFX_POWER_USB_EVT_READY : + (soc_evt == NRF_EVT_POWER_USB_REMOVED ) ? NRFX_POWER_USB_EVT_REMOVED : -1; + + if ( usbevt >= 0) tusb_hal_nrf_power_event(usbevt); + } + + return err; +} + +uint32_t proc_ble(void) +{ + // do nothing with ble + return NRF_ERROR_NOT_FOUND; +} + +void SD_EVT_IRQHandler(void) +{ + // process BLE and SOC until there is no more events + while( (NRF_ERROR_NOT_FOUND != proc_ble()) || (NRF_ERROR_NOT_FOUND != proc_soc()) ) + { + + } +} + +void nrf_error_cb(uint32_t id, uint32_t pc, uint32_t info) +{ + (void) id; + (void) pc; + (void) info; +} +#endif diff --git a/hw/bsp/itsybitsy_nrf52840/nrf52840_s140_v6.ld b/hw/bsp/itsybitsy_nrf52840/nrf52840_s140_v6.ld new file mode 100644 index 000000000..5314a4e93 --- /dev/null +++ b/hw/bsp/itsybitsy_nrf52840/nrf52840_s140_v6.ld @@ -0,0 +1,38 @@ +/* Linker script to configure memory regions. */ + +SEARCH_DIR(.) +GROUP(-lgcc -lc -lnosys) + +MEMORY +{ + FLASH (rx) : ORIGIN = 0x26000, LENGTH = 0xED000 - 0x26000 + + /* SRAM required by S132 depend on + * - Attribute Table Size + * - Vendor UUID count + * - Max ATT MTU + * - Concurrent connection peripheral + central + secure links + * - Event Len, HVN queue, Write CMD queue + */ + RAM (rwx) : ORIGIN = 0x20003400, LENGTH = 0x20040000 - 0x20003400 +} + +SECTIONS +{ + . = ALIGN(4); + .svc_data : + { + PROVIDE(__start_svc_data = .); + KEEP(*(.svc_data)) + PROVIDE(__stop_svc_data = .); + } > RAM + + .fs_data : + { + PROVIDE(__start_fs_data = .); + KEEP(*(.fs_data)) + PROVIDE(__stop_fs_data = .); + } > RAM +} INSERT AFTER .data; + +INCLUDE "nrf52_common.ld" -- cgit v1.3.1