From cf8a85fa8bc2ffe7130b7383dee64812bc2ebdce Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 26 Mar 2018 22:44:45 +0700 Subject: moving lpc43xx port into tusb's portable folder --- hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.c | 504 ----------------------------- hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.h | 161 --------- hw/mcu/nxp/lpc43xx/tusb_port/hal_lpc43xx.c | 193 ----------- 3 files changed, 858 deletions(-) delete mode 100644 hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.c delete mode 100644 hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.h delete mode 100644 hw/mcu/nxp/lpc43xx/tusb_port/hal_lpc43xx.c (limited to 'hw') diff --git a/hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.c b/hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.c deleted file mode 100644 index a1e44763d..000000000 --- a/hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.c +++ /dev/null @@ -1,504 +0,0 @@ -/**************************************************************************/ -/*! - @file dcd_lpc43xx.c - @author hathach (tinyusb.org) - - @section LICENSE - - Software License Agreement (BSD License) - - Copyright (c) 2013, hathach (tinyusb.org) - All rights reserved. - - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - 1. Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - 2. Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - 3. Neither the name of the copyright holders nor the - names of its contributors may be used to endorse or promote products - derived from this software without specific prior written permission. - - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY - EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED - WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY - DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES - (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; - LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND - ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS - SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - - This file is part of the tinyusb stack. -*/ -/**************************************************************************/ - -#include "tusb_option.h" - -#if MODE_DEVICE_SUPPORTED && TUSB_CFG_MCU == MCU_LPC43XX - -//--------------------------------------------------------------------+ -// INCLUDE -//--------------------------------------------------------------------+ -#include "common/tusb_common.h" -#include "tusb_hal.h" -#include "osal/osal.h" -#include "common/timeout_timer.h" - -#include "tusb_dcd.h" -#include "dcd_lpc43xx.h" - -#include "LPC43xx.h" -#include "lpc43xx_cgu.h" - - -//--------------------------------------------------------------------+ -// MACRO CONSTANT TYPEDEF -//--------------------------------------------------------------------+ - -//--------------------------------------------------------------------+ -// INTERNAL OBJECT & FUNCTION DECLARATION -//--------------------------------------------------------------------+ -typedef struct { - dcd_qhd_t qhd[DCD_QHD_MAX]; ///< Must be at 2K alignment - dcd_qtd_t qtd[DCD_QTD_MAX] ATTR_ALIGNED(32); - -}dcd_data_t; - -extern ATTR_WEAK dcd_data_t dcd_data0; -extern ATTR_WEAK dcd_data_t dcd_data1; - -#if (TUSB_CFG_CONTROLLER_0_MODE & TUSB_MODE_DEVICE) -TUSB_CFG_ATTR_USBRAM ATTR_ALIGNED(2048) STATIC_VAR dcd_data_t dcd_data0; -#endif - -#if (TUSB_CFG_CONTROLLER_1_MODE & TUSB_MODE_DEVICE) -TUSB_CFG_ATTR_USBRAM ATTR_ALIGNED(2048) STATIC_VAR dcd_data_t dcd_data1; -#endif - -static LPC_USB0_Type * const LPC_USB[2] = { LPC_USB0, ((LPC_USB0_Type*) LPC_USB1_BASE) }; -static dcd_data_t* const dcd_data_ptr[2] = { &dcd_data0, &dcd_data1 }; - -//--------------------------------------------------------------------+ -// CONTROLLER API -//--------------------------------------------------------------------+ -void tusb_dcd_connect(uint8_t rhport) -{ - LPC_USB[rhport]->USBCMD_D |= BIT_(0); -} - -void tusb_dcd_set_address(uint8_t rhport, uint8_t dev_addr) -{ - LPC_USB[rhport]->DEVICEADDR = (dev_addr << 25) | BIT_(24); -} - -void tusb_dcd_set_config(uint8_t rhport, uint8_t config_num) -{ - -} - -/// follows LPC43xx User Manual 23.10.3 -static void bus_reset(uint8_t rhport) -{ - LPC_USB0_Type* const lpc_usb = LPC_USB[rhport]; - - // The reset value for all endpoint types is the control endpoint. If one endpoint - //direction is enabled and the paired endpoint of opposite direction is disabled, then the - //endpoint type of the unused direction must bechanged from the control type to any other - //type (e.g. bulk). Leaving an unconfigured endpoint control will cause undefined behavior - //for the data PID tracking on the active endpoint. - lpc_usb->ENDPTCTRL1 = lpc_usb->ENDPTCTRL2 = lpc_usb->ENDPTCTRL3 = - (TUSB_XFER_BULK << 2) | (TUSB_XFER_BULK << 18); - - // USB1 only has 3 non-control endpoints - if ( rhport == 0) - { - lpc_usb->ENDPTCTRL4 = lpc_usb->ENDPTCTRL5 = (TUSB_XFER_BULK << 2) | (TUSB_XFER_BULK << 18); - } - - //------------- Clear All Registers -------------// - lpc_usb->ENDPTNAK = lpc_usb->ENDPTNAK; - lpc_usb->ENDPTNAKEN = 0; - lpc_usb->USBSTS_D = lpc_usb->USBSTS_D; - lpc_usb->ENDPTSETUPSTAT = lpc_usb->ENDPTSETUPSTAT; - lpc_usb->ENDPTCOMPLETE = lpc_usb->ENDPTCOMPLETE; - - while (lpc_usb->ENDPTPRIME); - lpc_usb->ENDPTFLUSH = 0xFFFFFFFF; - while (lpc_usb->ENDPTFLUSH); - - // read reset bit in portsc - - //------------- Queue Head & Queue TD -------------// - dcd_data_t* p_dcd = dcd_data_ptr[rhport]; - - memclr_(p_dcd, sizeof(dcd_data_t)); - - //------------- Set up Control Endpoints (0 OUT, 1 IN) -------------// - p_dcd->qhd[0].zero_length_termination = p_dcd->qhd[1].zero_length_termination = 1; - p_dcd->qhd[0].max_package_size = p_dcd->qhd[1].max_package_size = TUSB_CFG_DEVICE_CONTROL_ENDOINT_SIZE; - p_dcd->qhd[0].qtd_overlay.next = p_dcd->qhd[1].qtd_overlay.next = QTD_NEXT_INVALID; - - p_dcd->qhd[0].int_on_setup = 1; // OUT only - -} - -bool tusb_dcd_init(uint8_t rhport) -{ - LPC_USB0_Type* const lpc_usb = LPC_USB[rhport]; - dcd_data_t* p_dcd = dcd_data_ptr[rhport]; - - memclr_(p_dcd, sizeof(dcd_data_t)); - - lpc_usb->ENDPOINTLISTADDR = (uint32_t) p_dcd->qhd; // Endpoint List Address has to be 2K alignment - lpc_usb->USBSTS_D = lpc_usb->USBSTS_D; - lpc_usb->USBINTR_D = INT_MASK_USB | INT_MASK_ERROR | INT_MASK_PORT_CHANGE | INT_MASK_RESET | INT_MASK_SUSPEND | INT_MASK_SOF; - - lpc_usb->USBCMD_D &= ~0x00FF0000; // Interrupt Threshold Interval = 0 - lpc_usb->USBCMD_D |= BIT_(0); // connect - - // enable interrupt - NVIC_EnableIRQ(rhport ? USB1_IRQn : USB0_IRQn); - - return true; -} - -//--------------------------------------------------------------------+ -// PIPE HELPER -//--------------------------------------------------------------------+ -#if 0 -static inline uint8_t edpt_pos2phy(uint8_t pos) -{ // 0-5 --> OUT, 16-21 IN - return (pos < DCD_QHD_MAX/2) ? (2*pos) : (2*(pos-16)+1); -} -#endif - -static inline uint8_t edpt_phy2pos(uint8_t physical_endpoint) -{ - return physical_endpoint/2 + ( (physical_endpoint%2) ? 16 : 0); -} - -static inline uint8_t edpt_addr2phy(uint8_t endpoint_addr) -{ - return 2*(endpoint_addr & 0x0F) + ((endpoint_addr & TUSB_DIR_IN_MASK) ? 1 : 0); -} - -static inline uint8_t edpt_phy2addr(uint8_t ep_idx) -{ - return (ep_idx/2) | ( ep_idx & 0x01 ? TUSB_DIR_IN_MASK : 0 ); -} - -static inline uint8_t edpt_phy2log(uint8_t physical_endpoint) -{ - return physical_endpoint/2; -} - -static void qtd_init(dcd_qtd_t* p_qtd, void * data_ptr, uint16_t total_bytes) -{ - memclr_(p_qtd, sizeof(dcd_qtd_t)); - - p_qtd->used = 1; - - p_qtd->next = QTD_NEXT_INVALID; - p_qtd->active = 1; - p_qtd->total_bytes = p_qtd->expected_bytes = total_bytes; - - if (data_ptr != NULL) - { - p_qtd->buffer[0] = (uint32_t) data_ptr; - for(uint8_t i=1; i<5; i++) - { - p_qtd->buffer[i] |= align4k( p_qtd->buffer[i-1] ) + 4096; - } - } -} - -// retval 0: invalid -static inline uint8_t qtd_find_free(uint8_t rhport) -{ - // QTD0 is reserved for control transfer - for(uint8_t i=1; iqtd[i].used == 0) return i; - } - - return 0; -} - -//--------------------------------------------------------------------+ -// CONTROL PIPE API -//--------------------------------------------------------------------+ - -// control transfer does not need to use qtd find function -// follows UM 24.10.8.1.1 Setup packet handling using setup lockout mechanism -bool tusb_dcd_control_xfer(uint8_t rhport, tusb_dir_t dir, uint8_t * p_buffer, uint16_t length) -{ - LPC_USB0_Type* const lpc_usb = LPC_USB[rhport]; - dcd_data_t* const p_dcd = dcd_data_ptr[rhport]; - - uint8_t const ep_phy = (dir == TUSB_DIR_IN) ? 1 : 0; - - dcd_qhd_t* qhd = &p_dcd->qhd[ep_phy]; - - // wait until ENDPTSETUPSTAT before priming data/status in response TODO add time out - while(lpc_usb->ENDPTSETUPSTAT & BIT_(0)) {} - - VERIFY( !qhd->qtd_overlay.active ); - - dcd_qtd_t* qtd = &p_dcd->qtd[0]; - qtd_init(qtd, p_buffer, length); - - // skip xfer complete for Status - qtd->int_on_complete = (length > 0 ? 1 : 0); - - qhd->qtd_overlay.next = (uint32_t) qtd; - - lpc_usb->ENDPTPRIME = BIT_(edpt_phy2pos(ep_phy)); - - return true; -} - -//--------------------------------------------------------------------+ -// BULK/INTERRUPT/ISOCHRONOUS PIPE API -//--------------------------------------------------------------------+ -static inline volatile uint32_t * get_reg_control_addr(uint8_t rhport, uint8_t physical_endpoint) -{ - return &(LPC_USB[rhport]->ENDPTCTRL0) + edpt_phy2log(physical_endpoint); -} - -void tusb_dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) -{ - uint8_t ep_idx = edpt_addr2phy(ep_addr); - volatile uint32_t * reg_control = get_reg_control_addr(rhport, ep_idx); - - if ( ep_addr == 0) - { - // Stall both Control IN and OUT - (*reg_control) |= ( (ENDPTCTRL_MASK_STALL << 16) || (ENDPTCTRL_MASK_STALL << 0) ); - }else - { - (*reg_control) |= ENDPTCTRL_MASK_STALL << (ep_idx & 0x01 ? 16 : 0); - } -} - -void tusb_dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) -{ - volatile uint32_t * reg_control = get_reg_control_addr(rhport, edpt_addr2phy(ep_addr)); - - // data toggle also need to be reset - (*reg_control) |= ENDPTCTRL_MASK_TOGGLE_RESET << ((ep_addr & TUSB_DIR_IN_MASK) ? 16 : 0); - (*reg_control) &= ~(ENDPTCTRL_MASK_STALL << ((ep_addr & TUSB_DIR_IN_MASK) ? 16 : 0)); -} - -bool tusb_dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) -{ - // TODO USB1 only has 4 non-control enpoint (USB0 has 5) - // TODO not support ISO yet - VERIFY ( p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS); - - tusb_dir_t dir = (p_endpoint_desc->bEndpointAddress & TUSB_DIR_IN_MASK) ? TUSB_DIR_IN : TUSB_DIR_OUT; - - //------------- Prepare Queue Head -------------// - uint8_t ep_idx = edpt_addr2phy(p_endpoint_desc->bEndpointAddress); - dcd_qhd_t * p_qhd = &dcd_data_ptr[rhport]->qhd[ep_idx]; - - memclr_(p_qhd, sizeof(dcd_qhd_t)); - - p_qhd->zero_length_termination = 1; - p_qhd->max_package_size = p_endpoint_desc->wMaxPacketSize.size; - p_qhd->qtd_overlay.next = QTD_NEXT_INVALID; - - //------------- Endpoint Control Register -------------// - volatile uint32_t * reg_control = get_reg_control_addr(rhport, ep_idx); - - // endpoint must not be already enabled - VERIFY( !( (*reg_control) & (ENDPTCTRL_MASK_ENABLE << (dir ? 16 : 0)) ) ); - - (*reg_control) |= ((p_endpoint_desc->bmAttributes.xfer << 2) | ENDPTCTRL_MASK_ENABLE | ENDPTCTRL_MASK_TOGGLE_RESET) << (dir ? 16 : 0); - - return true; -} - -bool tusb_dcd_edpt_busy(uint8_t rhport, uint8_t ep_addr) -{ - uint8_t ep_idx = edpt_addr2phy(ep_addr); - dcd_qhd_t const * p_qhd = &dcd_data_ptr[rhport]->qhd[ep_idx]; - - return p_qhd->list_qtd_idx[0] != 0; // qtd list is not empty -// return !p_qhd->qtd_overlay.halted && p_qhd->qtd_overlay.active; -} - -// add only, controller virtually cannot know -// TODO remove and merge to tusb_dcd_edpt_xfer -static bool pipe_add_xfer(uint8_t rhport, uint8_t ed_idx, void * buffer, uint16_t total_bytes, bool int_on_complete) -{ - uint8_t qtd_idx = qtd_find_free(rhport); - TU_ASSERT(qtd_idx != 0); - - dcd_data_t* p_dcd = dcd_data_ptr[rhport]; - dcd_qhd_t * p_qhd = &p_dcd->qhd[ed_idx]; - dcd_qtd_t * p_qtd = &p_dcd->qtd[qtd_idx]; - - //------------- Find free slot in qhd's array list -------------// - uint8_t free_slot; - for(free_slot=0; free_slot < DCD_QTD_PER_QHD_MAX; free_slot++) - { - if ( p_qhd->list_qtd_idx[free_slot] == 0 ) break; // found free slot - } - TU_ASSERT(free_slot < DCD_QTD_PER_QHD_MAX); - - p_qhd->list_qtd_idx[free_slot] = qtd_idx; // add new qtd to qhd's array list - - //------------- Prepare qtd -------------// - qtd_init(p_qtd, buffer, total_bytes); - p_qtd->int_on_complete = int_on_complete; - - if ( free_slot > 0 ) p_dcd->qtd[ p_qhd->list_qtd_idx[free_slot-1] ].next = (uint32_t) p_qtd; - - return true; -} - -bool tusb_dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes) -{ - uint8_t ep_idx = edpt_addr2phy(ep_addr); - - VERIFY ( pipe_add_xfer(rhport, ep_idx, buffer, total_bytes, true) ); - - dcd_qhd_t* p_qhd = &dcd_data_ptr[rhport]->qhd[ ep_idx ]; - dcd_qtd_t* p_qtd = &dcd_data_ptr[rhport]->qtd[ p_qhd->list_qtd_idx[0] ]; - - p_qhd->qtd_overlay.next = (uint32_t) p_qtd; // attach head QTD to QHD start transferring - - LPC_USB[rhport]->ENDPTPRIME = BIT_( edpt_phy2pos(ep_idx) ) ; - - return true; -} - -//------------- Device Controller Driver's Interrupt Handler -------------// -void xfer_complete_isr(uint8_t rhport, uint32_t reg_complete) -{ - for(uint8_t ep_idx = 2; ep_idx < DCD_QHD_MAX; ep_idx++) - { - if ( BIT_TEST_(reg_complete, edpt_phy2pos(ep_idx)) ) - { // 23.10.12.3 Failed QTD also get ENDPTCOMPLETE set - dcd_qhd_t * p_qhd = &dcd_data_ptr[rhport]->qhd[ep_idx]; - - // retire all QTDs in array list, up to 1st still-active QTD - while( p_qhd->list_qtd_idx[0] != 0 ) - { - dcd_qtd_t * p_qtd = &dcd_data_ptr[rhport]->qtd[ p_qhd->list_qtd_idx[0] ]; - - if (p_qtd->active) break; // stop immediately if found still-active QTD and shift array list - - //------------- Free QTD and shift array list -------------// - p_qtd->used = 0; // free QTD - memmove( (void*) p_qhd->list_qtd_idx, (void*) (p_qhd->list_qtd_idx+1), DCD_QTD_PER_QHD_MAX-1); - p_qhd->list_qtd_idx[DCD_QTD_PER_QHD_MAX-1]=0; - - if (p_qtd->int_on_complete) - { - bool succeeded = ( p_qtd->xact_err || p_qtd->halted || p_qtd->buffer_err ) ? false : true; - - uint8_t ep_addr = edpt_phy2addr(ep_idx); - tusb_dcd_xfer_complete(rhport, ep_addr, p_qtd->expected_bytes - p_qtd->total_bytes, succeeded); // only number of bytes in the IOC qtd - } - } - } - } -} - -void hal_dcd_isr(uint8_t rhport) -{ - LPC_USB0_Type* const lpc_usb = LPC_USB[rhport]; - - uint32_t const int_enable = lpc_usb->USBINTR_D; - uint32_t const int_status = lpc_usb->USBSTS_D & int_enable; - lpc_usb->USBSTS_D = int_status; // Acknowledge handled interrupt - - if (int_status == 0) return;// disabled interrupt sources - - if (int_status & INT_MASK_RESET) - { - bus_reset(rhport); - tusb_dcd_bus_event(rhport, USBD_BUS_EVENT_RESET); - } - - if (int_status & INT_MASK_SUSPEND) - { - if (lpc_usb->PORTSC1_D & PORTSC_SUSPEND_MASK) - { // Note: Host may delay more than 3 ms before and/or after bus reset before doing enumeration. - if ((lpc_usb->DEVICEADDR >> 25) & 0x0f) - { - tusb_dcd_bus_event(0, USBD_BUS_EVENT_SUSPENDED); - } - } - } - - // TODO disconnection does not generate interrupt !!!!!! -// if (int_status & INT_MASK_PORT_CHANGE) -// { -// if ( !(lpc_usb->PORTSC1_D & PORTSC_CURRENT_CONNECT_STATUS_MASK) ) -// { -// tusb_dcd_bus_event(0, USBD_BUS_EVENT_UNPLUGGED); -// } -// } - - if (int_status & INT_MASK_USB) - { - uint32_t const edpt_complete = lpc_usb->ENDPTCOMPLETE; - lpc_usb->ENDPTCOMPLETE = edpt_complete; // acknowledge - - dcd_data_t* const p_dcd = dcd_data_ptr[rhport]; - - //------------- Set up Received -------------// - if (lpc_usb->ENDPTSETUPSTAT) - { - // 23.10.10.2 Operational model for setup transfers - lpc_usb->ENDPTSETUPSTAT = lpc_usb->ENDPTSETUPSTAT;// acknowledge - - tusb_dcd_setup_received(rhport, (uint8_t*) &p_dcd->qhd[0].setup_request); - } - //------------- Control Request Completed -------------// - else if ( edpt_complete & ( BIT_(0) | BIT_(16)) ) - { - for(uint8_t ep_idx = 0; ep_idx < 2; ep_idx++) - { - if ( BIT_TEST_(edpt_complete, edpt_phy2pos(ep_idx)) ) - { - // TODO use the actual QTD instead of the qhd's overlay to get expected bytes for actual byte xferred - dcd_qtd_t volatile * const p_qtd = &p_dcd->qhd[ep_idx].qtd_overlay; - - if ( p_qtd->int_on_complete ) - { - bool succeeded = ( p_qtd->xact_err || p_qtd->halted || p_qtd->buffer_err ) ? false : true; - (void) succeeded; - - tusb_dcd_control_complete(rhport); - } - } - } - } - - //------------- Transfer Complete -------------// - if ( edpt_complete & ~(BIT_(0) | BIT_(16)) ) - { - xfer_complete_isr(rhport, edpt_complete); - } - } - - if (int_status & INT_MASK_SOF) - { - tusb_dcd_bus_event(rhport, USBD_BUS_EVENT_SOF); - } - - if (int_status & INT_MASK_NAK) {} - if (int_status & INT_MASK_ERROR) ASSERT(false, VOID_RETURN); -} - -//--------------------------------------------------------------------+ -// HELPER -//--------------------------------------------------------------------+ -#endif diff --git a/hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.h b/hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.h deleted file mode 100644 index 673486f63..000000000 --- a/hw/mcu/nxp/lpc43xx/tusb_port/dcd_lpc43xx.h +++ /dev/null @@ -1,161 +0,0 @@ -/**************************************************************************/ -/*! - @file dcd_lpc43xx.h - @author hathach (tinyusb.org) - - @section LICENSE - - Software License Agreement (BSD License) - - Copyright (c) 2013, hathach (tinyusb.org) - All rights reserved. - - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - 1. Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - 2. Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - 3. Neither the name of the copyright holders nor the - names of its contributors may be used to endorse or promote products - derived from this software without specific prior written permission. - - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY - EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED - WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY - DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES - (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; - LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND - ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS - SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - - This file is part of the tinyusb stack. -*/ -/**************************************************************************/ - -/** \ingroup group_dcd - * \defgroup group_dcd_lpc143xx LPC43xx - * @{ */ - -#ifndef _TUSB_DCD_LPC43XX_H_ -#define _TUSB_DCD_LPC43XX_H_ - -#ifdef __cplusplus - extern "C" { -#endif - -//--------------------------------------------------------------------+ -// MACRO CONSTANT TYPEDEF -//--------------------------------------------------------------------+ -#define DCD_QHD_MAX 12 -#define DCD_QTD_MAX 12 -#define DCD_QTD_PER_QHD_MAX 2 // maximum number of qtd that are linked into one queue head at a time - -#define QTD_NEXT_INVALID 0x01 - -/*---------- ENDPTCTRL ----------*/ -enum { - ENDPTCTRL_MASK_STALL = BIT_(0), - ENDPTCTRL_MASK_TOGGLE_INHIBIT = BIT_(5), ///< used for test only - ENDPTCTRL_MASK_TOGGLE_RESET = BIT_(6), - ENDPTCTRL_MASK_ENABLE = BIT_(7) -}; - -/*---------- USBCMD ----------*/ -enum { - USBCMD_MASK_RUN_STOP = BIT_(0), - USBCMD_MASK_RESET = BIT_(1), - USBCMD_MASK_SETUP_TRIPWIRE = BIT_(13), - USBCMD_MASK_ADD_QTD_TRIPWIRE = BIT_(14) ///< This bit is used as a semaphore to ensure the to proper addition of a new dTD to an active (primed) endpoint’s linked list. This bit is set and cleared by software during the process of adding a new dTD -}; -// Interrupt Threshold bit 23:16 - -/*---------- USBSTS, USBINTR ----------*/ -enum { - INT_MASK_USB = BIT_(0), - INT_MASK_ERROR = BIT_(1), - INT_MASK_PORT_CHANGE = BIT_(2), - INT_MASK_RESET = BIT_(6), - INT_MASK_SOF = BIT_(7), - INT_MASK_SUSPEND = BIT_(8), - INT_MASK_NAK = BIT_(16) -}; - -//------------- PORTSC -------------// -enum { - PORTSC_CURRENT_CONNECT_STATUS_MASK = BIT_(0), - PORTSC_FORCE_PORT_RESUME_MASK = BIT_(6), - PORTSC_SUSPEND_MASK = BIT_(7) - -}; - -typedef struct { - // Word 0: Next QTD Pointer - uint32_t next; ///< Next link pointer This field contains the physical memory address of the next dTD to be processed - - // Word 1: qTQ Token - uint32_t : 3 ; - volatile uint32_t xact_err : 1 ; - uint32_t : 1 ; - volatile uint32_t buffer_err : 1 ; - volatile uint32_t halted : 1 ; - volatile uint32_t active : 1 ; - uint32_t : 2 ; - uint32_t iso_mult_override : 2 ; ///< This field can be used for transmit ISOs to override the MULT field in the dQH. This field must be zero for all packet types that are not transmit-ISO. - uint32_t : 3 ; - uint32_t int_on_complete : 1 ; - volatile uint32_t total_bytes : 15 ; - uint32_t : 0 ; - - // Word 2-6: Buffer Page Pointer List, Each element in the list is a 4K page aligned, physical memory address. The lower 12 bits in each pointer are reserved (except for the first one) as each memory pointer must reference the start of a 4K page - uint32_t buffer[5]; ///< buffer1 has frame_n for TODO Isochronous - - //------------- DCD Area -------------// - uint16_t expected_bytes; - uint8_t used; - uint8_t reserved; -} dcd_qtd_t; - -STATIC_ASSERT( sizeof(dcd_qtd_t) == 32, "size is not correct"); - -typedef struct ATTR_ALIGNED(64) { - // Word 0: Capabilities and Characteristics - uint32_t : 15 ; ///< Number of packets executed per transaction descriptor 00 - Execute N transactions as demonstrated by the USB variable length protocol where N is computed using Max_packet_length and the Total_bytes field in the dTD. 01 - Execute one transaction 10 - Execute two transactions 11 - Execute three transactions Remark: Non-isochronous endpoints must set MULT = 00. Remark: Isochronous endpoints must set MULT = 01, 10, or 11 as needed. - uint32_t int_on_setup : 1 ; ///< Interrupt on setup This bit is used on control type endpoints to indicate if USBINT is set in response to a setup being received. - uint32_t max_package_size : 11 ; ///< This directly corresponds to the maximum packet size of the associated endpoint (wMaxPacketSize) - uint32_t : 2 ; - uint32_t zero_length_termination : 1 ; ///< This bit is used for non-isochronous endpoints to indicate when a zero-length packet is received to terminate transfers in case the total transfer length is “multiple”. 0 - Enable zero-length packet to terminate transfers equal to a multiple of Max_packet_length (default). 1 - Disable zero-length packet on transfers that are equal in length to a multiple Max_packet_length. - uint32_t iso_mult : 2 ; ///< - uint32_t : 0 ; - - // Word 1: Current qTD Pointer - volatile uint32_t qtd_addr; - - // Word 2-9: Transfer Overlay - volatile dcd_qtd_t qtd_overlay; - - // Word 10-11: Setup request (control OUT only) - volatile tusb_control_request_t setup_request; - - //--------------------------------------------------------------------+ - /// Due to the fact QHD is 64 bytes aligned but occupies only 48 bytes - /// thus there are 16 bytes padding free that we can make use of. - //--------------------------------------------------------------------+ - volatile uint8_t list_qtd_idx[DCD_QTD_PER_QHD_MAX]; - - uint8_t reserved[16-DCD_QTD_PER_QHD_MAX]; -} dcd_qhd_t; - -STATIC_ASSERT( sizeof(dcd_qhd_t) == 64, "size is not correct"); - - -#ifdef __cplusplus - } -#endif - -#endif /* _TUSB_DCD_LPC43XX_H_ */ - -/** @} */ diff --git a/hw/mcu/nxp/lpc43xx/tusb_port/hal_lpc43xx.c b/hw/mcu/nxp/lpc43xx/tusb_port/hal_lpc43xx.c deleted file mode 100644 index 451ed72a4..000000000 --- a/hw/mcu/nxp/lpc43xx/tusb_port/hal_lpc43xx.c +++ /dev/null @@ -1,193 +0,0 @@ -/**************************************************************************/ -/*! - @file hal_lpc43xx.c - @author hathach (tinyusb.org) - - @section LICENSE - - Software License Agreement (BSD License) - - Copyright (c) 2013, hathach (tinyusb.org) - All rights reserved. - - Redistribution and use in source and binary forms, with or without - modification, are permitted provided that the following conditions are met: - 1. Redistributions of source code must retain the above copyright - notice, this list of conditions and the following disclaimer. - 2. Redistributions in binary form must reproduce the above copyright - notice, this list of conditions and the following disclaimer in the - documentation and/or other materials provided with the distribution. - 3. Neither the name of the copyright holders nor the - names of its contributors may be used to endorse or promote products - derived from this software without specific prior written permission. - - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS ''AS IS'' AND ANY - EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED - WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER BE LIABLE FOR ANY - DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES - INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; - LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION HOWEVER CAUSED AND - ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS - SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - - This file is part of the tinyusb stack. -*/ -/**************************************************************************/ - -#include "tusb.h" - -#if TUSB_CFG_MCU == MCU_LPC43XX - -#include "LPC43xx.h" -#include "lpc43xx_cgu.h" - -enum { - LPC43XX_USBMODE_DEVICE = 2, - LPC43XX_USBMODE_HOST = 3 -}; - -enum { - LPC43XX_USBMODE_VBUS_LOW = 0, - LPC43XX_USBMODE_VBUS_HIGH = 1 -}; - -#if TUSB_CFG_OS == TUSB_OS_NONE - -volatile uint32_t system_ticks = 0; - -void SysTick_Handler (void) -{ - system_ticks++; -} - -uint32_t tusb_hal_tick_get(void) -{ - return system_ticks; -} - -#endif - -void tusb_hal_dbg_breakpoint(void) -{ - // M0 cannot check if debugger is attached or not -#if defined(__CORTEX_M) && (__CORTEX_M > 0) - // check if debugger is attached - if ( (CoreDebug->DHCSR & CoreDebug_DHCSR_C_DEBUGEN_Msk) == CoreDebug_DHCSR_C_DEBUGEN_Msk) - { - __asm("BKPT #0\n"); - } -#endif -} - -void tusb_hal_int_enable(uint8_t rhport) -{ - NVIC_EnableIRQ(rhport ? USB1_IRQn : USB0_IRQn); -} - -void tusb_hal_int_disable(uint8_t rhport) -{ - NVIC_DisableIRQ(rhport ? USB1_IRQn : USB0_IRQn); -} - - -static void hal_controller_reset(uint8_t rhport) -{ // TODO timeout expired to prevent trap - volatile uint32_t * p_reg_usbcmd; - - p_reg_usbcmd = (rhport ? &LPC_USB1->USBCMD_D : &LPC_USB0->USBCMD_D); -// NXP chip powered with non-host mode --> sts bit is not correctly reflected - (*p_reg_usbcmd) |= BIT_(1); - -// timeout_timer_t timeout; -// timeout_set(&timeout, 2); // should not take longer the time to stop controller - while( ((*p_reg_usbcmd) & BIT_(1)) /*&& !timeout_expired(&timeout)*/) {} -// -// return timeout_expired(&timeout) ? TUSB_ERROR_OSAL_TIMEOUT : TUSB_ERROR_NONE; -} - -bool tusb_hal_init(void) -{ - LPC_CREG->CREG0 &= ~(1<<5); /* Turn on the phy */ - - //------------- USB0 -------------// -#if TUSB_CFG_CONTROLLER_0_MODE - CGU_EnableEntity(CGU_CLKSRC_PLL0, DISABLE); /* Disable PLL first */ - VERIFY( CGU_ERROR_SUCCESS == CGU_SetPLL0()); /* the usb core require output clock = 480MHz */ - CGU_EntityConnect(CGU_CLKSRC_XTAL_OSC, CGU_CLKSRC_PLL0); - CGU_EnableEntity(CGU_CLKSRC_PLL0, ENABLE); /* Enable PLL after all setting is done */ - - // reset controller & set role - hal_controller_reset(0); - - #if TUSB_CFG_CONTROLLER_0_MODE & TUSB_MODE_HOST - LPC_USB0->USBMODE_H = LPC43XX_USBMODE_HOST | (LPC43XX_USBMODE_VBUS_HIGH << 5); - #else // TODO OTG - LPC_USB0->USBMODE_D = LPC43XX_USBMODE_DEVICE; - LPC_USB0->OTGSC = (1<<3) | (1<<0) /*| (1<<16)| (1<<24)| (1<<25)| (1<<26)| (1<<27)| (1<<28)| (1<<29)| (1<<30)*/; - #if TUSB_CFG_DEVICE_FULLSPEED // TODO for easy testing - LPC_USB0->PORTSC1_D |= (1<<24); // force full speed - #endif - #endif -#endif - - //------------- USB1 -------------// -#if TUSB_CFG_CONTROLLER_1_MODE - // Host require to config P2_5, TODO confirm whether device mode require P2_5 or not - scu_pinmux(0x2, 5, MD_PLN | MD_EZI | MD_ZI, FUNC2); // USB1_VBUS monitor presence, must be high for bus reset occur - - /* connect CLK_USB1 to 60 MHz clock */ - CGU_EntityConnect(CGU_CLKSRC_PLL1, CGU_BASE_USB1); /* FIXME Run base BASE_USB1_CLK clock from PLL1 (assume PLL1 is 60 MHz, no division required) */ - LPC_SCU->SFSUSB = (TUSB_CFG_CONTROLLER_1_MODE & TUSB_MODE_HOST) ? 0x16 : 0x12; // enable USB1 with on-chip FS PHY - - hal_controller_reset(1); - - #if TUSB_CFG_CONTROLLER_1_MODE & TUSB_MODE_HOST - LPC_USB1->USBMODE_H = LPC43XX_USBMODE_HOST | (LPC43XX_USBMODE_VBUS_HIGH << 5); - #else // TODO OTG - LPC_USB1->USBMODE_D = LPC43XX_USBMODE_DEVICE; - #endif - - LPC_USB1->PORTSC1_D |= (1<<24); // TODO abstract, force rhport to fullspeed -#endif - - return true; -} - -void hal_dcd_isr(uint8_t rhport); - -#if TUSB_CFG_CONTROLLER_0_MODE -void USB0_IRQHandler(void) -{ - #if MODE_HOST_SUPPORTED - hal_hcd_isr(0); - #endif - - #if MODE_DEVICE_SUPPORTED - hal_dcd_isr(0); - #endif -} -#endif - -#if TUSB_CFG_CONTROLLER_1_MODE -void USB1_IRQHandler(void) -{ - #if MODE_HOST_SUPPORTED - hal_hcd_isr(1); - #endif - - #if MODE_DEVICE_SUPPORTED - hal_dcd_isr(1); - #endif -} -#endif - - -void check_failed(uint8_t *file, uint32_t line) -{ - (void) file; - (void) line; -} - -#endif -- cgit v1.3.1