From 4c510c12b1d0a0bfb0726c0100ff22cd892aa1e8 Mon Sep 17 00:00:00 2001 From: Gunar Schorcht Date: Mon, 27 Feb 2023 09:54:45 +0100 Subject: synopsys/dwc2: fix SOF interrupt handling SOF is not a flag of the GOTGINT register but of the GINTSTS register. Therefore the flag must be written in the GINTSTS register instead of the GOTGINT register to clear the interrupt. --- src/portable/synopsys/dwc2/dcd_dwc2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index c6132a1f5..7d4f31c48 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -1288,7 +1288,7 @@ void dcd_int_handler(uint8_t rhport) if(int_status & GINTSTS_SOF) { - dwc2->gotgint = GINTSTS_SOF; + dwc2->gintsts = GINTSTS_SOF; if (_sof_en) { -- cgit v1.3.1 From 410ad4d0f9ff166610655bae31328e4120b17ef2 Mon Sep 17 00:00:00 2001 From: Hubert Denkmair Date: Wed, 8 Mar 2023 12:05:58 +0100 Subject: add basic STM32G0 support --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 86 +++++++--- .../st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 180 +++++++++++++++------ 2 files changed, 198 insertions(+), 68 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index e49c0b52e..21ae8e6e8 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -216,7 +216,7 @@ TU_ATTR_ALWAYS_INLINE static inline void reg16_clear_bits(__IO uint16_t *reg, ui } // Bits in ISTR are cleared upon writing 0 -TU_ATTR_ALWAYS_INLINE static inline void clear_istr_bits(uint16_t mask) { +TU_ATTR_ALWAYS_INLINE static inline void clear_istr_bits(uint32_t mask) { USB->ISTR = ~mask; } @@ -242,16 +242,23 @@ void dcd_init (uint8_t rhport) { asm("NOP"); } + +#ifdef PMA_32BIT_ACCESS // CNTR register is 32bits on STM32G0, 16bit on older versions + USB->CNTR &= ~USB_CNTR_PDWN; +#else reg16_clear_bits(&USB->CNTR, USB_CNTR_PDWN);// Remove powerdown +#endif + // Wait startup time, for F042 and F070, this is <= 1 us. for(uint32_t i = 0; i<200; i++) // should be a few us { asm("NOP"); } USB->CNTR = 0; // Enable USB - - USB->BTABLE = DCD_STM32_BTABLE_BASE; +#ifndef STM32G0 // BTABLE register does not exist any more on STM32G0, it is fixed to USB SRAM base address + USB->BTABLE = DCD_STM32_BTABLE_BASE; +#endif USB->ISTR = 0; // Clear pending interrupts // Reset endpoints to disabled @@ -312,7 +319,7 @@ void dcd_sof_enable(uint8_t rhport, bool en) } else { - USB->CNTR &= (uint16_t) ~USB_CNTR_SOFM; + USB->CNTR &= ~USB_CNTR_SOFM; } } @@ -358,6 +365,9 @@ void dcd_int_enable (uint8_t rhport) NVIC_EnableIRQ(USB_LP_IRQn); NVIC_EnableIRQ(USBWakeUp_IRQn); +#elif CFG_TUSB_MCU == OPT_MCU_STM32G0 + NVIC_EnableIRQ(USB_UCPD1_2_IRQn); + #elif CFG_TUSB_MCU == OPT_MCU_STM32WB NVIC_EnableIRQ(USB_HP_IRQn); NVIC_EnableIRQ(USB_LP_IRQn); @@ -405,6 +415,9 @@ void dcd_int_disable(uint8_t rhport) NVIC_DisableIRQ(USB_LP_IRQn); NVIC_DisableIRQ(USBWakeUp_IRQn); +#elif CFG_TUSB_MCU == OPT_MCU_STM32G0 + NVIC_DisableIRQ(USB_UCPD1_2_IRQn); + #elif CFG_TUSB_MCU == OPT_MCU_STM32WB NVIC_DisableIRQ(USB_HP_IRQn); NVIC_DisableIRQ(USB_LP_IRQn); @@ -433,7 +446,7 @@ void dcd_remote_wakeup(uint8_t rhport) { (void) rhport; - USB->CNTR |= (uint16_t) USB_CNTR_RESUME; + USB->CNTR |= USB_CNTR_RESUME; remoteWakeCountdown = 4u; // required to be 1 to 15 ms, ESOF should trigger every 1ms. } @@ -534,9 +547,6 @@ static void dcd_ep_ctr_rx_handler(uint32_t wIstr) if((ep_addr == 0U) && ((wEPRegVal & USB_EP_SETUP) != 0U)) /* Setup packet */ { - // The setup_received function uses memcpy, so this must first copy the setup data into - // user memory, to allow for the 32-bit access that memcpy performs. - uint8_t userMemBuf[8]; uint32_t count = pcd_get_ep_rx_cnt(USB, EPindex); /* Get SETUP Packet*/ if(count == 8) // Setup packet should always be 8 bytes. If not, ignore it, and try again. @@ -544,8 +554,15 @@ static void dcd_ep_ctr_rx_handler(uint32_t wIstr) // Must reset EP to NAK (in case it had been stalling) (though, maybe too late here) pcd_set_ep_rx_status(USB,0u,USB_EP_RX_NAK); pcd_set_ep_tx_status(USB,0u,USB_EP_TX_NAK); - dcd_read_packet_memory(userMemBuf, *pcd_ep_rx_address_ptr(USB,EPindex), 8); +#ifdef PMA_32BIT_ACCESS + dcd_event_setup_received(0, (uint8_t*)(USB_PMAADDR + pcd_get_ep_rx_address(USB, EPindex)), true); +#else + // The setup_received function uses memcpy, so this must first copy the setup data into + // user memory, to allow for the 32-bit access that memcpy performs. + uint8_t userMemBuf[8]; + dcd_read_packet_memory(userMemBuf, pcd_get_ep_rx_address(USB,EPindex), 8); dcd_event_setup_received(0, (uint8_t*)userMemBuf, true); +#endif } } else @@ -568,7 +585,7 @@ static void dcd_ep_ctr_rx_handler(uint32_t wIstr) if (count != 0U) { - uint16_t addr = *pcd_ep_rx_address_ptr(USB, EPindex); + uint16_t addr = pcd_get_ep_rx_address(USB, EPindex); if (xfer->ff) { @@ -672,8 +689,13 @@ void dcd_int_handler(uint8_t rhport) { if (int_status & USB_ISTR_WKUP) { +#ifdef PMA_32BIT_ACCESS // CNTR register is 32bits on STM32G0, 16bit on older versions + USB->CNTR &= ~USB_CNTR_LPMODE; + USB->CNTR &= ~USB_CNTR_FSUSP; +#else reg16_clear_bits(&USB->CNTR, USB_CNTR_LPMODE); reg16_clear_bits(&USB->CNTR, USB_CNTR_FSUSP); +#endif clear_istr_bits(USB_ISTR_WKUP); dcd_event_bus_signal(0, DCD_EVENT_RESUME, true); } @@ -695,7 +717,7 @@ void dcd_int_handler(uint8_t rhport) { if(int_status & USB_ISTR_ESOF) { if(remoteWakeCountdown == 1u) { - USB->CNTR &= (uint16_t)(~USB_CNTR_RESUME); + USB->CNTR &= ~USB_CNTR_RESUME; } if(remoteWakeCountdown > 0u) { @@ -722,8 +744,13 @@ void dcd_edpt0_status_complete(uint8_t rhport, tusb_control_request_t const * re uint8_t const dev_addr = (uint8_t) request->wValue; // Setting new address after the whole request is complete +#ifdef PMA_32BIT_ACCESS + USB->DADDR &= ~USB_DADDR_ADD; + USB->DADDR = (USB->DADDR & ~USB_DADDR_ADD_Msk) | dev_addr; // leave the enable bit set +#else reg16_clear_bits(&USB->DADDR, USB_DADDR_ADD); USB->DADDR = (uint16_t)(USB->DADDR | dev_addr); // leave the enable bit set +#endif } } @@ -925,14 +952,14 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc if( (dir == TUSB_DIR_IN) || (wType == USB_EP_ISOCHRONOUS) ) { - *pcd_ep_tx_address_ptr(USB, ep_idx) = pma_addr; + pcd_set_ep_tx_address(USB, ep_idx, pma_addr); pcd_set_ep_tx_bufsize(USB, ep_idx, buffer_size); pcd_clear_tx_dtog(USB, ep_idx); } if( (dir == TUSB_DIR_OUT) || (wType == USB_EP_ISOCHRONOUS) ) { - *pcd_ep_rx_address_ptr(USB, ep_idx) = pma_addr; + pcd_set_ep_rx_address(USB, ep_idx, pma_addr); pcd_set_ep_rx_bufsize(USB, ep_idx, buffer_size); pcd_clear_rx_dtog(USB, ep_idx); } @@ -1011,10 +1038,10 @@ bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet xfer_ctl_ptr(ep_addr)->ep_idx = ep_idx; pcd_set_eptype(USB, ep_idx, USB_EP_ISOCHRONOUS); - - *pcd_ep_tx_address_ptr(USB, ep_idx) = pma_addr; - *pcd_ep_rx_address_ptr(USB, ep_idx) = pma_addr; - + + pcd_set_ep_tx_address(USB, ep_idx, pma_addr); + pcd_set_ep_rx_address(USB, ep_idx, pma_addr); + return true; } @@ -1063,7 +1090,7 @@ static void dcd_transmit_packet(xfer_ctl_t * xfer, uint16_t ep_ix) } uint16_t ep_reg = pcd_get_endpoint(USB, ep_ix); - uint16_t addr_ptr = *pcd_ep_tx_address_ptr(USB,ep_ix); + uint16_t addr_ptr = pcd_get_ep_tx_address(USB, ep_ix); if (xfer->ff) { @@ -1197,6 +1224,19 @@ void dcd_edpt_clear_stall (uint8_t rhport, uint8_t ep_addr) } } +#ifdef PMA_32BIT_ACCESS +static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, size_t wNBytes) +{ + // FIXME original function uses byte-access to source memory (to support non-aligned buffers) + const uint32_t* src32 = (uint32_t*)(src); + uint32_t* dst32 = (uint32_t*)(USB_PMAADDR + dst); + for (unsigned n=wNBytes/4; n>0; --n) { + *dst32++ = *src32++; + } + *dst32 = (*src32) & ((1<<8*(wNBytes % 4)) - 1); + return true; +} +#else // Packet buffer access can only be 8- or 16-bit. /** * @brief Copy a buffer from user memory area to packet memory area (PMA). @@ -1239,6 +1279,7 @@ static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, si return true; } +#endif /** * @brief Copy from FIFO to packet memory area (PMA). @@ -1290,6 +1331,14 @@ static bool dcd_write_packet_memory_ff(tu_fifo_t * ff, uint16_t dst, uint16_t wN return true; } +#ifdef PMA_32BIT_ACCESS +static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, size_t wNBytes) +{ + // FIXME this should probably be modified for possible unaligned access? + memcpy(dst, (void*)(USB_PMAADDR+src), wNBytes); + return true; +} +#else /** * @brief Copy a buffer from packet memory area (PMA) to user memory area. * Uses byte-access of system memory and 16-bit access of packet memory @@ -1323,6 +1372,7 @@ static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, size_t wN } return true; } +#endif /** * @brief Copy a buffer from user packet memory area (PMA) to FIFO. diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index 015b177cf..686bfaa66 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -82,6 +82,34 @@ #include "stm32g4xx.h" #define PMA_LENGTH (1024u) +#elif CFG_TUSB_MCU == OPT_MCU_STM32G0 + #include "STM32/stm32g0xx.h" + #define PMA_32BIT_ACCESS + #define PMA_LENGTH (1024u) // FIXME it is 2048, really + #undef USB_PMAADDR + #define USB_PMAADDR USB_DRD_PMAADDR + #define USB_TypeDef USB_DRD_TypeDef + #define EP0R CHEP0R + #define USB_EP_CTR_RX USB_EP_VTRX + #define USB_EP_CTR_TX USB_EP_VTTX + #define USB_EP_T_FIELD USB_CHEP_UTYPE + #define USB_EPREG_MASK USB_CHEP_REG_MASK + #define USB_EPTX_DTOGMASK USB_CHEP_TX_DTOGMASK + #define USB_EPRX_DTOGMASK USB_CHEP_RX_DTOGMASK + #define USB_EPTX_DTOG1 USB_CHEP_TX_DTOG1 + #define USB_EPTX_DTOG2 USB_CHEP_TX_DTOG2 + #define USB_EPRX_DTOG1 USB_CHEP_RX_DTOG1 + #define USB_EPRX_DTOG2 USB_CHEP_RX_DTOG2 + #define USB_EPRX_STAT USB_CH_RX_VALID + #define USB_EPKIND_MASK USB_EP_KIND_MASK + #define USB USB_DRD_FS + #define USB_CNTR_FRES USB_CNTR_USBRST + #define USB_CNTR_RESUME USB_CNTR_L2RES + #define USB_ISTR_EP_ID USB_ISTR_IDN + #define USB_EPADDR_FIELD USB_CHEP_ADDR + #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY + #define USB_CNTR_FSUSP USB_CNTR_SUSPEN + #elif CFG_TUSB_MCU == OPT_MCU_STM32WB #include "stm32wbxx.h" #define PMA_LENGTH (1024u) @@ -105,15 +133,31 @@ #define PMA_STRIDE (1u) #endif -// And for type-safety create a new macro for the volatile address of PMAADDR +// For type-safety create a new macro for the volatile address of PMAADDR // The compiler should warn us if we cast it to a non-volatile type? +#ifdef PMA_32BIT_ACCESS +static __IO uint32_t * const pma32 = (__IO uint32_t*)USB_PMAADDR; +#else // Volatile is also needed to prevent the optimizer from changing access to 32-bit (as 32-bit access is forbidden) static __IO uint16_t * const pma = (__IO uint16_t*)USB_PMAADDR; -// prototypes -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_rx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx); -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_tx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx); -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wRegValue); +TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t * pcd_btable_word_ptr(USB_TypeDef * USBx, size_t x) +{ + size_t total_word_offset = (((USBx)->BTABLE)>>1) + x; + total_word_offset *= PMA_STRIDE; + return &(pma[total_word_offset]); +} + +TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_tx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) +{ + return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 1u); +} + +TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_rx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) +{ + return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 3u); +} +#endif /* Aligned buffer size according to hardware */ TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_aligned_buffer_size(uint16_t size) @@ -131,13 +175,22 @@ TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_aligned_buffer_size(uint16_t si /* SetENDPOINT */ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wRegValue) { +#ifdef PMA_32BIT_ACCESS + __O uint32_t *reg = (__O uint32_t *)(USB_DRD_BASE + bEpIdx*4); + *reg = wRegValue; +#else __O uint16_t *reg = (__O uint16_t *)((&USBx->EP0R) + bEpIdx*2u); *reg = (uint16_t)wRegValue; +#endif } /* GetENDPOINT */ -TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_get_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx) { +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx) { +#ifdef PMA_32BIT_ACCESS + __I uint32_t *reg = (__I uint32_t *)(USB_DRD_BASE + bEpIdx*4); +#else __I uint16_t *reg = (__I uint16_t *)((&USBx->EP0R) + bEpIdx*2u); +#endif return *reg; } @@ -187,34 +240,22 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_ep_ctr(USB_TypeDef * USBx, */ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { +#ifdef PMA_32BIT_ACCESS + return (pma32[2*bEpIdx] & 0x03FF0000) >> 16; +#else __I uint16_t *regPtr = pcd_ep_tx_cnt_ptr(USBx, bEpIdx); return *regPtr & 0x3ffU; +#endif } TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { +#ifdef PMA_32BIT_ACCESS + return (pma32[2*bEpIdx + 1] & 0x03FF0000) >> 16; +#else __I uint16_t *regPtr = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); return *regPtr & 0x3ffU; -} - -/** - * @brief Sets counter of rx buffer with no. of blocks. - * @param dwReg Register - * @param wCount Counter. - * @param wNBlocks no. of Blocks. - * @retval None - */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_cnt_reg(__O uint16_t * pdwReg, size_t wCount) -{ - /* We assume that the buffer size is already aligned to hardware requirements. */ - uint16_t blocksize = (wCount > 62) ? 1 : 0; - uint16_t numblocks = wCount / (blocksize ? 32 : 2); - - /* There should be no remainder in the above calculation */ - TU_ASSERT((wCount - (numblocks * (blocksize ? 32 : 2))) == 0, /**/); - - /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ - *pdwReg = (blocksize << 15) | ((numblocks - blocksize) << 10); +#endif } /** @@ -233,57 +274,96 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_address(USB_TypeDef * USBx, pcd_set_endpoint(USBx, bEpIdx,regVal); } -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t * pcd_btable_word_ptr(USB_TypeDef * USBx, size_t x) +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { - size_t total_word_offset = (((USBx)->BTABLE)>>1) + x; - total_word_offset *= PMA_STRIDE; - return &(pma[total_word_offset]); +#ifdef PMA_32BIT_ACCESS + return pma32[2*bEpIdx] & 0x0000FFFFu ; +#else + return *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 0u); +#endif } -// Pointers to the PMA table entries (using the ARM address space) -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_tx_address_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { - return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 0u); -} -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_tx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) -{ - return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 1u); +#ifdef PMA_32BIT_ACCESS + return pma32[2*bEpIdx + 1] & 0x0000FFFFu; +#else + return *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 2u); +#endif } -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_rx_address_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { - return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 2u); +#ifdef PMA_32BIT_ACCESS + pma32[2*bEpIdx] = (pma32[2*bEpIdx] & 0xFFFF0000u) | (addr & 0x0000FFFCu); +#else + *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 0u) = addr; +#endif } -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_rx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { - return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 3u); +#ifdef PMA_32BIT_ACCESS + pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & 0xFFFF0000u) | (addr & 0x0000FFFCu); +#else + *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 2u) = addr; +#endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { +#ifdef PMA_32BIT_ACCESS + pma32[2*bEpIdx] = (pma32[2*bEpIdx] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); +#else __IO uint16_t * reg = pcd_ep_tx_cnt_ptr(USBx, bEpIdx); *reg = (uint16_t) (*reg & (uint16_t) ~0x3FFU) | (wCount & 0x3FFU); +#endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { +#ifdef PMA_32BIT_ACCESS + pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); +#else __IO uint16_t * reg = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); *reg = (uint16_t) (*reg & (uint16_t) ~0x3FFU) | (wCount & 0x3FFU); +#endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_blsize_num_blocks(USB_TypeDef * USBx, uint32_t rxtx_idx, uint32_t blocksize, uint32_t numblocks) { - __IO uint16_t *pdwReg = pcd_ep_tx_cnt_ptr((USBx),(bEpIdx)); - wCount = pcd_aligned_buffer_size(wCount); - pcd_set_ep_cnt_reg(pdwReg, wCount); + /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ +#ifdef PMA_32BIT_ACCESS + pma32[rxtx_idx] = (pma32[rxtx_idx] & 0x0000FFFFu) | (blocksize << 31) | ((numblocks - blocksize) << 26); +#else + __IO uint16_t *pdwReg = pcd_btable_word_ptr(USBx, rxtx_idx*2u + 1u); + *pdwReg = (blocksize << 15) | ((numblocks - blocksize) << 10); +#endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_bufsize(USB_TypeDef * USBx, uint32_t rxtx_idx, uint32_t wCount) { - __IO uint16_t *pdwReg = pcd_ep_rx_cnt_ptr((USBx),(bEpIdx)); wCount = pcd_aligned_buffer_size(wCount); - pcd_set_ep_cnt_reg(pdwReg, wCount); + + /* We assume that the buffer size is already aligned to hardware requirements. */ + uint16_t blocksize = (wCount > 62) ? 1 : 0; + uint16_t numblocks = wCount / (blocksize ? 32 : 2); + + /* There should be no remainder in the above calculation */ + TU_ASSERT((wCount - (numblocks * (blocksize ? 32 : 2))) == 0, /**/); + + /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ + pcd_set_ep_blsize_num_blocks(USBx, rxtx_idx, blocksize, numblocks); +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) +{ + pcd_set_ep_bufsize(USBx, 2*bEpIdx, wCount); +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) +{ + pcd_set_ep_bufsize(USBx, 2*bEpIdx + 1, wCount); } /** -- cgit v1.3.1 From b3ad560e629be18146fd52e32235cc2ed72dc70b Mon Sep 17 00:00:00 2001 From: Hubert Denkmair Date: Wed, 8 Mar 2023 14:22:11 +0100 Subject: fix path to stm32g0xx.h --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index 686bfaa66..00791eeb7 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -83,7 +83,7 @@ #define PMA_LENGTH (1024u) #elif CFG_TUSB_MCU == OPT_MCU_STM32G0 - #include "STM32/stm32g0xx.h" + #include "stm32g0xx.h" #define PMA_32BIT_ACCESS #define PMA_LENGTH (1024u) // FIXME it is 2048, really #undef USB_PMAADDR -- cgit v1.3.1 From f8a21fff171aa272360c89dab5faca4f688a656a Mon Sep 17 00:00:00 2001 From: Hubert Denkmair Date: Sun, 12 Mar 2023 15:51:07 +0100 Subject: dcd_write_packet_memory: use volatile modifier for destination pointer --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 21ae8e6e8..e2e1cf484 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -1228,8 +1228,8 @@ void dcd_edpt_clear_stall (uint8_t rhport, uint8_t ep_addr) static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, size_t wNBytes) { // FIXME original function uses byte-access to source memory (to support non-aligned buffers) - const uint32_t* src32 = (uint32_t*)(src); - uint32_t* dst32 = (uint32_t*)(USB_PMAADDR + dst); + const uint32_t* src32 = (const uint32_t*)(src); + volatile uint32_t* dst32 = (volatile uint32_t*)(USB_PMAADDR + dst); for (unsigned n=wNBytes/4; n>0; --n) { *dst32++ = *src32++; } -- cgit v1.3.1 From 413b0a7da5b9ef1e519e4087a577bfc6d6681d97 Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Fri, 14 Apr 2023 17:12:47 +0200 Subject: Use PLL clock. --- hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h | 38 +++++++++++---------------- hw/bsp/stm32g0/family.c | 14 +++------- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 1 + 3 files changed, 21 insertions(+), 32 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h b/hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h index 3f5bc60b7..60357d1e8 100644 --- a/hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h +++ b/hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h @@ -62,7 +62,7 @@ static inline void board_clock_init(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; - RCC_CRSInitTypeDef pInit = {0}; + RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = { 0 }; /** Tick priority is used in HAL_RCC_OscConfig, so we need to enable it now */ @@ -75,38 +75,32 @@ static inline void board_clock_init(void) /** Initializes the RCC Oscillators according to the specified parameters * in the RCC_OscInitTypeDef structure. */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_HSI48; - RCC_OscInitStruct.HSIState = RCC_HSI_ON; - RCC_OscInitStruct.HSI48State = RCC_HSI48_ON; - RCC_OscInitStruct.HSIDiv = RCC_HSI_DIV1; - RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT; - RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE; + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV1; + RCC_OscInitStruct.PLL.PLLN = 12; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; + RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV2; + RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV2; HAL_RCC_OscConfig(&RCC_OscInitStruct); + /* Select HSI48 as USB clock source */ + PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USB; + PeriphClkInitStruct.UsbClockSelection = RCC_USBCLKSOURCE_PLL; + HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct); + /** Initializes the CPU, AHB and APB buses clocks */ RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK |RCC_CLOCKTYPE_PCLK1; - RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0); - /** Enable the SYSCFG APB clock - */ - __HAL_RCC_CRS_CLK_ENABLE(); - - /** Configures CRS - */ - pInit.Prescaler = RCC_CRS_SYNC_DIV1; - pInit.Source = RCC_CRS_SYNC_SOURCE_USB; - pInit.Polarity = RCC_CRS_SYNC_POLARITY_RISING; - pInit.ReloadValue = __HAL_RCC_CRS_RELOADVALUE_CALCULATE(48000000,1000); - pInit.ErrorLimitValue = 34; - pInit.HSI48CalibrationValue = 32; - - HAL_RCCEx_CRSConfig(&pInit); } #ifdef __cplusplus diff --git a/hw/bsp/stm32g0/family.c b/hw/bsp/stm32g0/family.c index 585398974..be356efe9 100644 --- a/hw/bsp/stm32g0/family.c +++ b/hw/bsp/stm32g0/family.c @@ -53,6 +53,9 @@ void board_init(void) __HAL_RCC_GPIOD_CLK_ENABLE(); __HAL_RCC_GPIOE_CLK_ENABLE(); + __HAL_RCC_SYSCFG_CLK_ENABLE(); + __HAL_RCC_PWR_CLK_ENABLE(); + UART_CLK_EN(); #if CFG_TUSB_OS == OPT_OS_NONE @@ -119,16 +122,7 @@ void board_init(void) __HAL_RCC_USB_CLK_ENABLE(); /* Enable VDDUSB */ - if(__HAL_RCC_PWR_IS_CLK_DISABLED()) - { - __HAL_RCC_PWR_CLK_ENABLE(); - HAL_PWREx_EnableVddUSB(); - __HAL_RCC_PWR_CLK_DISABLE(); - } - else - { - HAL_PWREx_EnableVddUSB(); - } + HAL_PWREx_EnableVddUSB(); } //--------------------------------------------------------------------+ diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 36b9133be..23b328b49 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -44,6 +44,7 @@ * L0x2, L0x3 1024 byte buffer * L1 512 byte buffer * L4x2, L4x3 1024 byte buffer + * G0 2048 byte buffer * * To use this driver, you must: * - If you are using a device with crystal-less USB, set up the clock recovery system (CRS) -- cgit v1.3.1 From 2f2c8ce9ec4a567603cbd5e0420fc3dcaffbdfb6 Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Fri, 14 Apr 2023 17:54:25 +0200 Subject: Fix GCC build. --- hw/bsp/board_mcu.h | 3 +++ hw/bsp/stm32g0/family.mk | 2 +- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 12 ++++++++++-- src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 11 +++++++++++ 4 files changed, 25 insertions(+), 3 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/board_mcu.h b/hw/bsp/board_mcu.h index cd195a19b..6d40aa0d1 100644 --- a/hw/bsp/board_mcu.h +++ b/hw/bsp/board_mcu.h @@ -101,6 +101,9 @@ #elif CFG_TUSB_MCU == OPT_MCU_STM32U5 #include "stm32u5xx.h" +#elif CFG_TUSB_MCU == OPT_MCU_STM32G0 + #include "stm32g0xx.h" + #elif CFG_TUSB_MCU == OPT_MCU_CXD56 // no header needed diff --git a/hw/bsp/stm32g0/family.mk b/hw/bsp/stm32g0/family.mk index faf92dca9..76f59fc34 100644 --- a/hw/bsp/stm32g0/family.mk +++ b/hw/bsp/stm32g0/family.mk @@ -51,7 +51,7 @@ INC += \ $(TOP)/$(ST_HAL_DRIVER)/Inc # For freeRTOS port source -FREERTOS_PORT = ARM_CM0 +FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM0 # flash target using on-board stlink flash: flash-stlink diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 23b328b49..32bab2bed 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -367,7 +367,11 @@ void dcd_int_enable (uint8_t rhport) NVIC_EnableIRQ(USBWakeUp_IRQn); #elif CFG_TUSB_MCU == OPT_MCU_STM32G0 - NVIC_EnableIRQ(USB_UCPD1_2_IRQn); + #ifdef STM32G0B0xx + NVIC_EnableIRQ(USB_IRQn); + #else + NVIC_EnableIRQ(USB_UCPD1_2_IRQn); + #endif #elif CFG_TUSB_MCU == OPT_MCU_STM32WB NVIC_EnableIRQ(USB_HP_IRQn); @@ -420,7 +424,11 @@ void dcd_int_disable(uint8_t rhport) NVIC_DisableIRQ(USBWakeUp_IRQn); #elif CFG_TUSB_MCU == OPT_MCU_STM32G0 - NVIC_DisableIRQ(USB_UCPD1_2_IRQn); + #ifdef STM32G0B0xx + NVIC_DisableIRQ(USB_IRQn); + #else + NVIC_DisableIRQ(USB_UCPD1_2_IRQn); + #endif #elif CFG_TUSB_MCU == OPT_MCU_STM32WB NVIC_DisableIRQ(USB_HP_IRQn); diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index c0f923c8f..32f715e6e 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -184,6 +184,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_aligned_buffer_size(uint16_t si TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wRegValue) { #ifdef PMA_32BIT_ACCESS + (void) USBx; __O uint32_t *reg = (__O uint32_t *)(USB_DRD_BASE + bEpIdx*4); *reg = wRegValue; #else @@ -195,6 +196,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, ui /* GetENDPOINT */ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef PMA_32BIT_ACCESS + (void) USBx; __I uint32_t *reg = (__I uint32_t *)(USB_DRD_BASE + bEpIdx*4); #else __I uint16_t *reg = (__I uint16_t *)((&USBx->EP0R) + bEpIdx*2u); @@ -249,6 +251,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_ep_ctr(USB_TypeDef * USBx, TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef PMA_32BIT_ACCESS + (void) USBx; return (pma32[2*bEpIdx] & 0x03FF0000) >> 16; #else __I uint16_t *regPtr = pcd_ep_tx_cnt_ptr(USBx, bEpIdx); @@ -259,6 +262,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USB TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef PMA_32BIT_ACCESS + (void) USBx; return (pma32[2*bEpIdx + 1] & 0x03FF0000) >> 16; #else __I uint16_t *regPtr = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); @@ -285,6 +289,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_address(USB_TypeDef * USBx, TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef PMA_32BIT_ACCESS + (void) USBx; return pma32[2*bEpIdx] & 0x0000FFFFu ; #else return *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 0u); @@ -294,6 +299,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef PMA_32BIT_ACCESS + (void) USBx; return pma32[2*bEpIdx + 1] & 0x0000FFFFu; #else return *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 2u); @@ -303,6 +309,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { #ifdef PMA_32BIT_ACCESS + (void) USBx; pma32[2*bEpIdx] = (pma32[2*bEpIdx] & 0xFFFF0000u) | (addr & 0x0000FFFCu); #else *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 0u) = addr; @@ -312,6 +319,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USB TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { #ifdef PMA_32BIT_ACCESS + (void) USBx; pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & 0xFFFF0000u) | (addr & 0x0000FFFCu); #else *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 2u) = addr; @@ -321,6 +329,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USB TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { #ifdef PMA_32BIT_ACCESS + (void) USBx; pma32[2*bEpIdx] = (pma32[2*bEpIdx] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); #else __IO uint16_t * reg = pcd_ep_tx_cnt_ptr(USBx, bEpIdx); @@ -331,6 +340,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, u TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { #ifdef PMA_32BIT_ACCESS + (void) USBx; pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); #else __IO uint16_t * reg = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); @@ -342,6 +352,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_blsize_num_blocks(USB_TypeDe { /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ #ifdef PMA_32BIT_ACCESS + (void) USBx; pma32[rxtx_idx] = (pma32[rxtx_idx] & 0x0000FFFFu) | (blocksize << 31) | ((numblocks - blocksize) << 26); #else __IO uint16_t *pdwReg = pcd_btable_word_ptr(USBx, rxtx_idx*2u + 1u); -- cgit v1.3.1 From 818bda18c23e17c08c689b543d77ecc944681dea Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Fri, 14 Apr 2023 23:34:20 +0200 Subject: Fix FIFO transfer and buffer alignment. --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 166 +++++++++++++++++---- .../st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 2 +- 2 files changed, 142 insertions(+), 26 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 32bab2bed..b8d04331a 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -186,12 +186,12 @@ static void dcd_ep_ctr_handler(void); static uint8_t open_ep_count; static uint16_t ep_buf_ptr; ///< Points to first free memory location static void dcd_pma_alloc_reset(void); -static uint16_t dcd_pma_alloc(uint8_t ep_addr, size_t length); +static uint16_t dcd_pma_alloc(uint8_t ep_addr, uint16_t length); static void dcd_pma_free(uint8_t ep_addr); static void dcd_ep_free(uint8_t ep_addr); static uint8_t dcd_ep_alloc(uint8_t ep_addr, uint8_t ep_type); -static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, size_t wNBytes); -static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, size_t wNBytes); +static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, uint16_t wNBytes); +static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, uint16_t wNBytes); static bool dcd_write_packet_memory_ff(tu_fifo_t * ff, uint16_t dst, uint16_t wNBytes); static bool dcd_read_packet_memory_ff(tu_fifo_t * ff, uint16_t src, uint16_t wNBytes); @@ -792,7 +792,7 @@ static void dcd_pma_alloc_reset(void) * * During failure, TU_ASSERT is used. If this happens, rework/reallocate memory manually. */ -static uint16_t dcd_pma_alloc(uint8_t ep_addr, size_t length) +static uint16_t dcd_pma_alloc(uint8_t ep_addr, uint16_t length) { xfer_ctl_t* epXferCtl = xfer_ctl_ptr(ep_addr); @@ -804,6 +804,13 @@ static uint16_t dcd_pma_alloc(uint8_t ep_addr, size_t length) return epXferCtl->pma_ptr; } + // Ensure allocated buffer is aligned +#ifdef PMA_32BIT_ACCESS + length = (length + 3) & ~0x03; +#else + length = (length + 1) & ~0x01; +#endif + open_ep_count++; uint16_t addr = ep_buf_ptr; @@ -814,7 +821,7 @@ static uint16_t dcd_pma_alloc(uint8_t ep_addr, size_t length) epXferCtl->pma_ptr = addr; epXferCtl->pma_alloc_size = length; - //TU_LOG2("dcd_pma_alloc(%x,%x)=%x\r\n",ep_addr,length,addr); + //TU_LOG1("dcd_pma_alloc(%x,%x)=%x\r\n",ep_addr,length,addr); return addr; } @@ -1240,15 +1247,36 @@ void dcd_edpt_clear_stall (uint8_t rhport, uint8_t ep_addr) } #ifdef PMA_32BIT_ACCESS -static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, size_t wNBytes) +static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, uint16_t wNBytes) { - // FIXME original function uses byte-access to source memory (to support non-aligned buffers) - const uint32_t* src32 = (const uint32_t*)(src); + const uint8_t* srcVal = src; volatile uint32_t* dst32 = (volatile uint32_t*)(USB_PMAADDR + dst); - for (unsigned n=wNBytes/4; n>0; --n) { - *dst32++ = *src32++; + + for (uint32_t n = wNBytes / 4; n > 0; --n) { + *dst32++ = tu_unaligned_read32(srcVal); + srcVal += 4; + } + + wNBytes = wNBytes & 0x03; + if (wNBytes) + { + uint32_t wrVal = *srcVal; + wNBytes--; + + if (wNBytes) + { + wrVal |= *++srcVal << 8; + wNBytes--; + + if (wNBytes) + { + wrVal |= *++srcVal << 16; + } + } + + *dst32 = wrVal; } - *dst32 = (*src32) & ((1<<8*(wNBytes % 4)) - 1); + return true; } #else @@ -1263,7 +1291,7 @@ static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, si * @param wNBytes no. of bytes to be copied. * @retval None */ -static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, size_t wNBytes) +static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, uint16_t wNBytes) { uint32_t n = (uint32_t)wNBytes >> 1U; uint16_t temp1, temp2; @@ -1286,7 +1314,7 @@ static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, si srcVal++; } - if (wNBytes & 0x01) + if (wNBytes) { temp1 = *srcVal; *pdwVal = temp1; @@ -1313,7 +1341,37 @@ static bool dcd_write_packet_memory_ff(tu_fifo_t * ff, uint16_t dst, uint16_t wN // We want to read from the FIFO and write it into the PMA, if LIN part is ODD and has WRAPPED part, // last lin byte will be combined with wrapped part - // To ensure PMA is always access 16bit aligned (dst aligned to 16 bit) + // To ensure PMA is always access aligned (dst aligned to 16 or 32 bit) +#ifdef PMA_32BIT_ACCESS + if((cnt_lin & 0x03) && cnt_wrap) + { + // Copy first linear part + dcd_write_packet_memory(dst, info.ptr_lin, cnt_lin &~0x03); + dst += cnt_lin &~0x03; + + // Copy last linear bytes & first wrapped bytes to buffer + uint32_t i; + uint8_t tmp[4]; + for (i = 0; i < (cnt_lin & 0x03); i++) + { + tmp[i] = ((uint8_t*)info.ptr_lin)[(cnt_lin &~0x03) + i]; + } + uint32_t wCnt = cnt_wrap; + for (; i < 4 && wCnt > 0; i++, wCnt--) + { + tmp[i] = *(uint8_t*)info.ptr_wrap; + info.ptr_wrap = (uint8_t*)info.ptr_wrap + 1; + } + + // Write unaligned buffer + dcd_write_packet_memory(dst, &tmp, 4); + dst += 4; + + // Copy rest of wrapped byte + if (wCnt) + dcd_write_packet_memory(dst, info.ptr_wrap, wCnt); + } +#else if((cnt_lin & 0x01) && cnt_wrap) { // Copy first linear part @@ -1328,6 +1386,7 @@ static bool dcd_write_packet_memory_ff(tu_fifo_t * ff, uint16_t dst, uint16_t wN // Copy rest of wrapped byte dcd_write_packet_memory(dst, ((uint8_t*)info.ptr_wrap) + 1, cnt_wrap - 1); } +#endif else { // Copy linear part @@ -1347,11 +1406,37 @@ static bool dcd_write_packet_memory_ff(tu_fifo_t * ff, uint16_t dst, uint16_t wN } #ifdef PMA_32BIT_ACCESS -static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, size_t wNBytes) +static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, uint16_t wNBytes) { - // FIXME this should probably be modified for possible unaligned access? - memcpy(dst, (void*)(USB_PMAADDR+src), wNBytes); - return true; + uint8_t* dstVal = dst; + volatile uint32_t* src32 = (volatile uint32_t*)(USB_PMAADDR + src); + + for (uint32_t n = wNBytes / 4; n > 0; --n) { + tu_unaligned_write32(dstVal, *src32++); + dstVal += 4; + } + + wNBytes = wNBytes & 0x03; + if (wNBytes) + { + uint32_t rdVal = *src32; + + *dstVal = tu_u32_byte0(rdVal); + wNBytes--; + + if (wNBytes) + { + *++dstVal = tu_u32_byte1(rdVal); + wNBytes--; + + if (wNBytes) + { + *++dstVal = tu_u32_byte2(rdVal); + } + } + } + + return true; } #else /** @@ -1360,7 +1445,7 @@ static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, size_t wN * @param wNBytes no. of bytes to be copied. * @retval None */ -static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, size_t wNBytes) +static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, uint16_t wNBytes) { uint32_t n = (uint32_t)wNBytes >> 1U; // The GCC optimizer will combine access to 32-bit sizes if we let it. Force @@ -1405,9 +1490,39 @@ static bool dcd_read_packet_memory_ff(tu_fifo_t * ff, uint16_t src, uint16_t wNB uint16_t cnt_lin = TU_MIN(wNBytes, info.len_lin); uint16_t cnt_wrap = TU_MIN(wNBytes - cnt_lin, info.len_wrap); + // We want to read from PMA and write it into the FIFO, if LIN part is ODD and has WRAPPED part, // last lin byte will be combined with wrapped part - // To ensure PMA is always access 16bit aligned (src aligned to 16 bit) + // To ensure PMA is always access aligned (src aligned to 16 or 32 bit) +#ifdef PMA_32BIT_ACCESS + if((cnt_lin & 0x03) && cnt_wrap) + { + // Copy first linear part + dcd_read_packet_memory(info.ptr_lin, src, cnt_lin &~0x03); + src += cnt_lin &~0x03; + + // Copy last linear bytes & first wrapped bytes + uint8_t tmp[4]; + dcd_read_packet_memory(tmp, src, 4); + src += 4; + + uint32_t i; + for (i = 0; i < (cnt_lin & 0x03); i++) + { + ((uint8_t*)info.ptr_lin)[(cnt_lin &~0x03) + i] = tmp[i]; + } + uint32_t wCnt = cnt_wrap; + for (; i < 4 && wCnt > 0; i++, wCnt--) + { + *(uint8_t*)info.ptr_wrap = tmp[i]; + info.ptr_wrap = (uint8_t*)info.ptr_wrap + 1; + } + + // Copy rest of wrapped byte + if (wCnt) + dcd_read_packet_memory(info.ptr_wrap, src, wCnt); + } +#else if((cnt_lin & 0x01) && cnt_wrap) { // Copy first linear part @@ -1415,16 +1530,17 @@ static bool dcd_read_packet_memory_ff(tu_fifo_t * ff, uint16_t src, uint16_t wNB src += cnt_lin &~0x01; // Copy last linear byte & first wrapped byte - uint16_t tmp; - dcd_read_packet_memory(&tmp, src, 2); - - ((uint8_t*)info.ptr_lin)[cnt_lin - 1] = (uint8_t)tmp; - ((uint8_t*)info.ptr_wrap)[0] = (uint8_t)(tmp >> 8U); + uint8_t tmp[2]; + dcd_read_packet_memory(tmp, src, 2); src += 2; + ((uint8_t*)info.ptr_lin)[cnt_lin - 1] = tmp[0]; + ((uint8_t*)info.ptr_wrap)[0] = tmp[1]; + // Copy rest of wrapped byte dcd_read_packet_memory(((uint8_t*)info.ptr_wrap) + 1, src, cnt_wrap - 1); } +#endif else { // Copy linear part diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index 32f715e6e..e6649de5a 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -85,7 +85,7 @@ #elif CFG_TUSB_MCU == OPT_MCU_STM32G0 #include "stm32g0xx.h" #define PMA_32BIT_ACCESS - #define PMA_LENGTH (1024u) // FIXME it is 2048, really + #define PMA_LENGTH (2048u) #undef USB_PMAADDR #define USB_PMAADDR USB_DRD_PMAADDR #define USB_TypeDef USB_DRD_TypeDef -- cgit v1.3.1 From 412b557a080526fbfe7b42dd8aa07468c16413cc Mon Sep 17 00:00:00 2001 From: Mengsk Date: Mon, 17 Apr 2023 15:34:20 +0200 Subject: Cleanup unnecessary code for 16bit access. --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 39 +++++---------------------- 1 file changed, 7 insertions(+), 32 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index b8d04331a..14cabaf8d 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -210,17 +210,6 @@ TU_ATTR_ALWAYS_INLINE static inline xfer_ctl_t* xfer_ctl_ptr(uint32_t ep_addr) return &xfer_status[epnum][dir]; } -// Using a function due to better type checks -// This seems better than having to do type casts everywhere else -TU_ATTR_ALWAYS_INLINE static inline void reg16_clear_bits(__IO uint16_t *reg, uint16_t mask) { - *reg = (uint16_t)(*reg & ~mask); -} - -// Bits in ISTR are cleared upon writing 0 -TU_ATTR_ALWAYS_INLINE static inline void clear_istr_bits(uint32_t mask) { - USB->ISTR = ~mask; -} - //--------------------------------------------------------------------+ // Controller API //--------------------------------------------------------------------+ @@ -244,11 +233,7 @@ void dcd_init (uint8_t rhport) asm("NOP"); } -#ifdef PMA_32BIT_ACCESS // CNTR register is 32bits on STM32G0, 16bit on older versions USB->CNTR &= ~USB_CNTR_PDWN; -#else - reg16_clear_bits(&USB->CNTR, USB_CNTR_PDWN);// Remove powerdown -#endif // Wait startup time, for F042 and F070, this is <= 1 us. for(uint32_t i = 0; i<200; i++) // should be a few us @@ -492,7 +477,6 @@ static void dcd_handle_bus_reset(void) //__IO uint16_t * const epreg = &(EPREG(0)); USB->DADDR = 0u; // disable USB peripheral by clearing the EF flag - for(uint32_t i=0; iISTR &=~USB_ISTR_SOF; dcd_event_sof(0, USB->FNR & USB_FNR_FN, true); } if(int_status & USB_ISTR_RESET) { // USBRST is start of reset. - clear_istr_bits(USB_ISTR_RESET); + USB->ISTR &=~USB_ISTR_RESET; dcd_handle_bus_reset(); dcd_event_bus_reset(0, TUSB_SPEED_FULL, true); return; // Don't do the rest of the things here; perhaps they've been cleared? @@ -704,14 +688,10 @@ void dcd_int_handler(uint8_t rhport) { if (int_status & USB_ISTR_WKUP) { -#ifdef PMA_32BIT_ACCESS // CNTR register is 32bits on STM32G0, 16bit on older versions USB->CNTR &= ~USB_CNTR_LPMODE; USB->CNTR &= ~USB_CNTR_FSUSP; -#else - reg16_clear_bits(&USB->CNTR, USB_CNTR_LPMODE); - reg16_clear_bits(&USB->CNTR, USB_CNTR_FSUSP); -#endif - clear_istr_bits(USB_ISTR_WKUP); + + USB->ISTR &=~USB_ISTR_WKUP; dcd_event_bus_signal(0, DCD_EVENT_RESUME, true); } @@ -725,7 +705,7 @@ void dcd_int_handler(uint8_t rhport) { USB->CNTR |= USB_CNTR_LPMODE; /* clear of the ISTR bit must be done after setting of CNTR_FSUSP */ - clear_istr_bits(USB_ISTR_SUSP); + USB->ISTR &=~USB_ISTR_SUSP; dcd_event_bus_signal(0, DCD_EVENT_SUSPEND, true); } @@ -738,7 +718,7 @@ void dcd_int_handler(uint8_t rhport) { { remoteWakeCountdown--; } - clear_istr_bits(USB_ISTR_ESOF); + USB->ISTR &=~USB_ISTR_ESOF; } } @@ -759,13 +739,8 @@ void dcd_edpt0_status_complete(uint8_t rhport, tusb_control_request_t const * re uint8_t const dev_addr = (uint8_t) request->wValue; // Setting new address after the whole request is complete -#ifdef PMA_32BIT_ACCESS USB->DADDR &= ~USB_DADDR_ADD; - USB->DADDR = (USB->DADDR & ~USB_DADDR_ADD_Msk) | dev_addr; // leave the enable bit set -#else - reg16_clear_bits(&USB->DADDR, USB_DADDR_ADD); - USB->DADDR = (uint16_t)(USB->DADDR | dev_addr); // leave the enable bit set -#endif + USB->DADDR |= dev_addr; // leave the enable bit set } } -- cgit v1.3.1 From be54870c3b2f7f1c14b0f5527f4928c8a4a4a7ae Mon Sep 17 00:00:00 2001 From: Martino Facchin Date: Wed, 3 May 2023 10:02:24 +0200 Subject: renesas_ra: add support for HS port --- hw/bsp/ra/family.mk | 2 + src/portable/renesas/rusb2/dcd_rusb2.c | 76 ++++++++++++++++++++++++++++------ src/portable/renesas/rusb2/hcd_rusb2.c | 46 ++++++++++++++------ src/portable/renesas/rusb2/rusb2_ra.c | 16 +++++++ src/portable/renesas/rusb2/rusb2_ra.h | 37 ++++++++++++++--- 5 files changed, 147 insertions(+), 30 deletions(-) create mode 100644 src/portable/renesas/rusb2/rusb2_ra.c (limited to 'src/portable') diff --git a/hw/bsp/ra/family.mk b/hw/bsp/ra/family.mk index d48272e61..3ed17f79f 100644 --- a/hw/bsp/ra/family.mk +++ b/hw/bsp/ra/family.mk @@ -22,6 +22,7 @@ CFLAGS += \ SRC_C += \ src/portable/renesas/rusb2/dcd_rusb2.c \ src/portable/renesas/rusb2/hcd_rusb2.c \ + src/portable/renesas/rusb2/rusb2_ra.c \ hw/mcu/renesas/fsp/ra/fsp/src/bsp/cmsis/Device/RENESAS/Source/startup.c \ hw/mcu/renesas/fsp/ra/fsp/src/bsp/cmsis/Device/RENESAS/Source/system.c \ hw/mcu/renesas/fsp/ra/fsp/src/bsp/mcu/all/bsp_clocks.c \ @@ -47,6 +48,7 @@ INC += \ $(TOP)/hw/mcu/renesas/fsp/ra/fsp/inc \ $(TOP)/hw/mcu/renesas/fsp/ra/fsp/inc/api \ $(TOP)/hw/mcu/renesas/fsp/ra/fsp/inc/instances \ + $(TOP)/hw/mcu/renesas/fsp/ra/fsp/src/bsp/mcu/all \ $(TOP)/$(FSP_MCU_DIR) \ $(TOP)/$(FSP_BOARD_DIR) diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 78584125f..9ae36e253 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -52,8 +52,10 @@ /* LINK core registers */ #if defined(__CCRX__) #define RUSB2 ((RUSB2_REG_t __evenaccess*) RUSB2_REG_BASE) +#elif (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) + #define RUSB2 ((R_USB_HS0_Type*)R_USB_HS0_BASE) #else - #define RUSB2 ((RUSB2_REG_t*) RUSB2_REG_BASE) + #define RUSB2 ((R_USB_FS0_Type*)R_USB_FS0_BASE) #endif /* Start of definition of packed structs (used by the CCRX toolchain) */ @@ -81,6 +83,18 @@ typedef union TU_ATTR_PACKED { volatile uint16_t u16; } hw_fifo_t; +typedef union TU_ATTR_PACKED { + struct { + volatile uint32_t : 24; + volatile uint32_t u8: 8; + }; + struct { + volatile uint32_t : 16; + volatile uint32_t u16: 16; + }; + volatile uint32_t u32; +} hw_fifo32_t; + typedef struct TU_ATTR_PACKED { void *buf; /* the start address of a transfer data buffer */ @@ -185,14 +199,18 @@ static inline void pipe_wait_for_ready(unsigned num) static void pipe_write_packet(void *buf, volatile void *fifo, unsigned len) { +#if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) + volatile hw_fifo32_t *reg = (volatile hw_fifo32_t*) fifo; +#else volatile hw_fifo_t *reg = (volatile hw_fifo_t*) fifo; +#endif uintptr_t addr = (uintptr_t)buf; while (len >= 2) { reg->u16 = *(const uint16_t *)addr; addr += 2; len -= 2; } - if (len) { + if (len > 0) { reg->u8 = *(const uint8_t *)addr; ++addr; } @@ -519,12 +537,17 @@ static void process_bus_reset(uint8_t rhport) ++ctr; } tu_varclr(&_dcd); + +#if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) + dcd_event_bus_reset(rhport, TUSB_SPEED_HIGH, true); +#else dcd_event_bus_reset(rhport, TUSB_SPEED_FULL, true); +#endif } static void process_set_address(uint8_t rhport) { - const uint32_t addr = RUSB2->USBADDR_b.USBADDR; + const uint32_t addr = RUSB2->USBADDR & 0xFF; if (!addr) return; const tusb_control_request_t setup_packet = { #if defined(__CCRX__) @@ -572,34 +595,53 @@ void dcd_init(uint8_t rhport) { (void)rhport; -#if 0 // previously present in the rx driver before generalization - uint32_t pswi = disable_interrupt(); - SYSTEM.PRCR.WORD = SYSTEM_PRCR_PRKEY | SYSTEM_PRCR_PRC1; - MSTP(USB0) = 0; - SYSTEM.PRCR.WORD = SYSTEM_PRCR_PRKEY; - enable_interrupt(pswi); -#endif - +#if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) + RUSB2->SYSCFG_b.HSE = 1; + RUSB2->PHYSET_b.DIRPD = 0; + R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MILLISECONDS); + RUSB2->PHYSET_b.PLLRESET = 0; + //RUSB2->PHYSET_b.REPSTART = 1; + RUSB2->SYSCFG_b.DRPD = 0; + RUSB2->SYSCFG_b.USBE = 1; + RUSB2->LPSTS_b.SUSPENDM = 1; + while (!RUSB2->PLLSTA_b.PLLLOCK); + //RUSB2->BUSWAIT |= 0x0F00U; + //RUSB2->PHYSET_b.REPSEL = 1; + RUSB2->CFIFOSEL_b.MBW = 1; + RUSB2->D0FIFOSEL_b.MBW = 1; + RUSB2->D1FIFOSEL_b.MBW = 1; + RUSB2->INTSTS0 = 0; +#else RUSB2->SYSCFG_b.SCKE = 1; while (!RUSB2->SYSCFG_b.SCKE) ; RUSB2->SYSCFG_b.DRPD = 0; RUSB2->SYSCFG_b.DCFM = 0; RUSB2->SYSCFG_b.USBE = 1; +#endif // MCU specific PHY init rusb2_phy_init(); +#if (CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) RUSB2->PHYSLEW = 0x5; RUSB2->DPUSR0R_FS_b.FIXPHY0 = 0u; /* USB_BASE Transceiver Output fixed */ + #define USB_VDCEN (0x0080U) /* b7: Regulator ON/OFF control */ + RUSB2->USBMC = (uint16_t) (RUSB2->USBMC | (USB_VDCEN)); +#endif + /* Setup default control pipe */ RUSB2->DCPMAXP_b.MXPS = 64; RUSB2->INTENB0 = RUSB2_INTSTS0_VBINT_Msk | RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_BEMP_Msk | RUSB2_INTSTS0_DVST_Msk | RUSB2_INTSTS0_CTRT_Msk | (USE_SOF ? RUSB2_INTSTS0_SOFR_Msk : 0) | - RUSB2_INTSTS0_RESM_Msk; + RUSB2_INTSTS0_RESM_Msk | RUSB2_INTSTS0_NRDY_Msk; RUSB2->BEMPENB = 1; RUSB2->BRDYENB = 1; +#if (CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) + RUSB2->SYSCFG_b.DPRPU = 1; /* necessary in this position */ +#endif + if (RUSB2->INTSTS0_b.VBSTS) { dcd_connect(rhport); } @@ -630,6 +672,10 @@ void dcd_remote_wakeup(uint8_t rhport) void dcd_connect(uint8_t rhport) { (void)rhport; + #if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) + RUSB2->SYSCFG_b.CNEN = 1; + R_BSP_SoftwareDelay((uint32_t) 10, BSP_DELAY_UNITS_MILLISECONDS); + #endif RUSB2->SYSCFG_b.DPRPU = 1; } @@ -672,6 +718,9 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) /* setup pipe */ dcd_int_disable(rhport); + #if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) + RUSB2->PIPEBUF = 0x7C08; + #endif RUSB2->PIPESEL = num; RUSB2->PIPEMAXP = mps; volatile uint16_t *ctr = get_pipectr(num); @@ -826,6 +875,9 @@ void dcd_int_handler(uint8_t rhport) break; } } + if (is0 & RUSB2_INTSTS0_NRDY_Msk) { + RUSB2->NRDYSTS = 0; + } if (is0 & RUSB2_INTSTS0_CTRT_Msk) { if (is0 & RUSB2_INTSTS0_CTSQ_CTRL_RDATA) { /* A setup packet has been received. */ diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index e4743223e..03811d63f 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -48,8 +48,10 @@ /* LINK core registers */ #if defined(__CCRX__) #define RUSB2 ((RUSB2_REG_t __evenaccess*) RUSB2_REG_BASE) +#elif (CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST) + #define RUSB2 ((R_USB_HS0_Type*) R_USB_HS0_BASE) #else - #define RUSB2 ((RUSB2_REG_t*) RUSB2_REG_BASE) + #define RUSB2 ((R_USB_FS0_Type*) R_USB_FS0_BASE) #endif TU_ATTR_PACKED_BEGIN @@ -477,31 +479,49 @@ bool hcd_init(uint8_t rhport) { (void)rhport; -#if 0 // previously present in the rx driver before generalization - uint32_t pswi = disable_interrupt(); - SYSTEM.PRCR.WORD = SYSTEM_PRCR_PRKEY | SYSTEM_PRCR_PRC1; - MSTP(USB0) = 0; - SYSTEM.PRCR.WORD = SYSTEM_PRCR_PRKEY; - enable_interrupt(pswi); -#endif - - RUSB2->SYSCFG_b.SCKE = 1; - while (!RUSB2->SYSCFG_b.SCKE) ; - RUSB2->SYSCFG_b.DPRPU = 0; - RUSB2->SYSCFG_b.DRPD = 0; +#if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST) + RUSB2->SYSCFG_b.HSE = 1; + RUSB2->PHYSET_b.HSEB = 0; + RUSB2->PHYSET_b.DIRPD = 0; + R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MILLISECONDS); + RUSB2->PHYSET_b.PLLRESET = 0; + RUSB2->LPSTS_b.SUSPENDM = 1; + while (!RUSB2->PLLSTA_b.PLLLOCK); + RUSB2->SYSCFG_b.DRPD = 1; RUSB2->SYSCFG_b.DCFM = 1; + RUSB2->SYSCFG_b.DPRPU = 0; + RUSB2->SYSCFG_b.CNEN = 1; + RUSB2->BUSWAIT |= 0x0F00U; + RUSB2->SOFCFG_b.INTL = 1; + RUSB2->DVSTCTR0_b.VBUSEN = 1; + RUSB2->CFIFOSEL_b.MBW = 1; + RUSB2->D0FIFOSEL_b.MBW = 1; + RUSB2->D1FIFOSEL_b.MBW = 1; + RUSB2->INTSTS0 = 0; + for (volatile int i = 0; i < 30000; ++i) ; + RUSB2->SYSCFG_b.USBE = 1; +#else + /* HOST DEVICE Full SPEED */ + RUSB2->SYSCFG_b.SCKE = 1; /* USB Clock enable */ + while (!RUSB2->SYSCFG_b.SCKE) ; + RUSB2->SYSCFG_b.DPRPU = 0; /* D+ pull up enable - 0/disable in host mode */ + RUSB2->SYSCFG_b.DRPD = 1; /* D+/D- pull down - 1/in Host mode (pag.834)*/ + RUSB2->SYSCFG_b.DCFM = 1; /* HOST or Device - 1/HOST */ RUSB2->DVSTCTR0_b.VBUSEN = 1; RUSB2->SYSCFG_b.DRPD = 1; for (volatile int i = 0; i < 30000; ++i) ; RUSB2->SYSCFG_b.USBE = 1; +#endif // MCU specific PHY init rusb2_phy_init(); +#if (CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST) RUSB2->PHYSLEW = 0x5; RUSB2->DPUSR0R_FS_b.FIXPHY0 = 0u; /* Transceiver Output fixed */ +#endif /* Setup default control pipe */ RUSB2->DCPCFG = RUSB2_PIPECFG_SHTNAK_Msk; diff --git a/src/portable/renesas/rusb2/rusb2_ra.c b/src/portable/renesas/rusb2/rusb2_ra.c new file mode 100644 index 000000000..2b6ce7b2f --- /dev/null +++ b/src/portable/renesas/rusb2/rusb2_ra.c @@ -0,0 +1,16 @@ +#include "tusb_option.h" +#include "rusb2_ra.h" + +#ifdef CFG_TUSB_RHPORT0_MODE +IRQn_Type _usb_fs_irqn = USBFS_INT_IRQn; +void tud_set_irq_usbfs(IRQn_Type q) { + _usb_fs_irqn = q; +} +#endif + +#ifdef CFG_TUSB_RHPORT1_MODE +IRQn_Type _usb_hs_irqn = USBHS_USB_INT_RESUME_IRQn; +void tud_set_irq_usbhs(IRQn_Type q) { + _usb_hs_irqn = q; +} +#endif \ No newline at end of file diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 5785850cc..b18b506e5 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -34,18 +34,45 @@ extern "C" { /* renesas fsp api */ #include "bsp_api.h" -#define RUSB2_REG_BASE (0x40090000) +extern IRQn_Type _usb_fs_irqn; +extern IRQn_Type _usb_hs_irqn; TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_enable(uint8_t rhport) { - (void) rhport; - NVIC_EnableIRQ(TU_IRQn); +#ifdef CFG_TUSB_RHPORT1_MODE +#if (CFG_TUSB_RHPORT1_MODE != 0) + if (rhport == 1) { + NVIC_EnableIRQ(_usb_hs_irqn); + } +#endif +#endif + +#ifdef CFG_TUSB_RHPORT0_MODE +#if (CFG_TUSB_RHPORT0_MODE != 0) + if (rhport == 0) { + NVIC_EnableIRQ(_usb_fs_irqn); + } +#endif +#endif } TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_disable(uint8_t rhport) { - (void) rhport; - NVIC_DisableIRQ(TU_IRQn); +#ifdef CFG_TUSB_RHPORT1_MODE +#if (CFG_TUSB_RHPORT1_MODE != 0) + if (rhport == 1) { + NVIC_DisableIRQ(_usb_hs_irqn); + } +#endif +#endif + +#ifdef CFG_TUSB_RHPORT0_MODE +#if (CFG_TUSB_RHPORT0_MODE != 0) + if (rhport == 0) { + NVIC_DisableIRQ(_usb_fs_irqn); + } +#endif +#endif } // MCU specific PHY init -- cgit v1.3.1 From 4afed62646d18dd96eef619d7d21b47a2422672f Mon Sep 17 00:00:00 2001 From: Martino Facchin Date: Wed, 3 May 2023 10:05:29 +0200 Subject: renesas_ra: host: handle retry on attach() --- src/portable/renesas/rusb2/hcd_rusb2.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 03811d63f..9dd4f0a48 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -759,9 +759,10 @@ void hcd_int_handler(uint8_t rhport) 7, 17, 0, 25, 22, 31, 15, 29, 10, 12, 6, 0, 21, 14, 9, 5, 20, 8, 19, 18}; #endif - + static unsigned char attach_attempt = 0; unsigned is1 = RUSB2->INTSTS1; unsigned is0 = RUSB2->INTSTS0; + /* clear active bits except VALID (don't write 0 to already cleared bits according to the HW manual) */ RUSB2->INTSTS1 = ~((RUSB2_INTSTS1_SACK_Msk | RUSB2_INTSTS1_SIGN_Msk | RUSB2_INTSTS1_ATTCH_Msk | RUSB2_INTSTS1_DTCH_Msk) & is1); RUSB2->INTSTS0 = ~((RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_NRDY_Msk | RUSB2_INTSTS0_BEMP_Msk) & is0); @@ -772,12 +773,21 @@ void hcd_int_handler(uint8_t rhport) if (is1 & RUSB2_INTSTS1_SACK_Msk) { /* Set DATA1 in advance for the next transfer. */ RUSB2->DCPCTR_b.SQSET = 1; + attach_attempt = 0; hcd_event_xfer_complete(RUSB2->DCPMAXP_b.DEVSEL, tu_edpt_addr(0, TUSB_DIR_OUT), 8, XFER_RESULT_SUCCESS, true); } if (is1 & RUSB2_INTSTS1_SIGN_Msk) { hcd_event_xfer_complete(RUSB2->DCPMAXP_b.DEVSEL, tu_edpt_addr(0, TUSB_DIR_OUT), 8, XFER_RESULT_FAILED, true); + if(attach_attempt > 0) { + RUSB2->DVSTCTR0_b.UACT = 1; + _hcd.need_reset = true; + RUSB2->INTENB1 = (RUSB2->INTENB1 & ~RUSB2_INTSTS1_ATTCH_Msk) | RUSB2_INTSTS1_DTCH_Msk; + hcd_event_device_attach(rhport, true); + } + attach_attempt--; } if (is1 & RUSB2_INTSTS1_ATTCH_Msk) { + attach_attempt = 10; RUSB2->DVSTCTR0_b.UACT = 1; _hcd.need_reset = true; RUSB2->INTENB1 = (RUSB2->INTENB1 & ~RUSB2_INTSTS1_ATTCH_Msk) | RUSB2_INTSTS1_DTCH_Msk; -- cgit v1.3.1 From 5f7e7b4b0a9f65a401c679d5045b96b4b56755df Mon Sep 17 00:00:00 2001 From: Martino Facchin Date: Wed, 3 May 2023 10:06:13 +0200 Subject: renesas_ra: support RA2A1 (FS only) --- src/portable/renesas/rusb2/dcd_rusb2.c | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 9ae36e253..f3bda5205 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -41,6 +41,15 @@ #include "rusb2_rx.h" #elif TU_CHECK_MCU(OPT_MCU_RAXXX) #include "rusb2_ra.h" + #if defined(RENESAS_CORTEX_M23) + #define D0FIFO CFIFO + #define D0FIFOSEL CFIFOSEL + #define D0FIFOSEL_b CFIFOSEL_b + #define D1FIFOSEL CFIFOSEL + #define D1FIFOSEL_b CFIFOSEL_b + #define D0FIFOCTR CFIFOCTR + #define D0FIFOCTR_b CFIFOCTR_b + #endif #else #error "Unsupported MCU" #endif @@ -121,6 +130,10 @@ typedef struct //--------------------------------------------------------------------+ static dcd_data_t _dcd; +#ifndef FIRST_BULK_PIPE +#define FIRST_BULK_PIPE 3 +#endif + static unsigned find_pipe(unsigned xfer) { switch (xfer) { @@ -130,7 +143,7 @@ static unsigned find_pipe(unsigned xfer) } break; case TUSB_XFER_BULK: - for (int i = 3; i <= 5; ++i) { + for (int i = FIRST_BULK_PIPE; i <= 5; ++i) { if (0 == _dcd.pipe[i].ep) return i; } for (int i = 1; i <= 1; ++i) { -- cgit v1.3.1 From 6ff62c0fe85e825d077d7d803c657181769e542f Mon Sep 17 00:00:00 2001 From: Martino Facchin Date: Wed, 3 May 2023 11:47:41 +0200 Subject: renesas: add fallback for targets not defining CFG_TUSB_RHPORT*_MODE --- src/portable/renesas/rusb2/dcd_rusb2.c | 5 +++++ src/portable/renesas/rusb2/hcd_rusb2.c | 5 +++++ src/portable/renesas/rusb2/rusb2_ra.h | 5 +++++ 3 files changed, 15 insertions(+) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index f3bda5205..f509dcc56 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -37,6 +37,11 @@ #include "device/dcd.h" #include "rusb2_type.h" +#if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE) +// fallback +#define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE +#endif + #if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) #include "rusb2_rx.h" #elif TU_CHECK_MCU(OPT_MCU_RAXXX) diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 9dd4f0a48..1ec25f1e2 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -33,6 +33,11 @@ #include "host/hcd.h" #include "rusb2_type.h" +#if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE) +// fallback +#define CFG_TUSB_RHPORT0_MODE OPT_MODE_HOST +#endif + #if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) #include "rusb2_rx.h" #elif TU_CHECK_MCU(OPT_MCU_RAXXX) diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index b18b506e5..874492304 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -37,6 +37,11 @@ extern "C" { extern IRQn_Type _usb_fs_irqn; extern IRQn_Type _usb_hs_irqn; +#if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE) +// fallback +#define CFG_TUSB_RHPORT0_MODE ( CFG_TUD_ENABLED ? OPT_MODE_DEVICE : OPT_MODE_HOST ) +#endif + TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_enable(uint8_t rhport) { #ifdef CFG_TUSB_RHPORT1_MODE -- cgit v1.3.1 From 77f0726361c66bf2783c1ce68e0f00bdd5f58229 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 9 May 2023 17:32:14 +0700 Subject: fix ehci issue with portsc when enable port power and port reset fix attached device not regconized if attached before power on --- .idea/runConfigurations/rt1060_redlink.xml | 10 ++ hw/bsp/imxrt/boards/mimxrt1060_evk/board.cmake | 1 + hw/bsp/imxrt/family.cmake | 19 +++- src/portable/ehci/ehci.c | 90 ++++++++++------- src/portable/ehci/ehci.h | 132 +++++++++++++++++-------- 5 files changed, 171 insertions(+), 81 deletions(-) create mode 100644 .idea/runConfigurations/rt1060_redlink.xml (limited to 'src/portable') diff --git a/.idea/runConfigurations/rt1060_redlink.xml b/.idea/runConfigurations/rt1060_redlink.xml new file mode 100644 index 000000000..a6f345fac --- /dev/null +++ b/.idea/runConfigurations/rt1060_redlink.xml @@ -0,0 +1,10 @@ + + + + + + + + + \ No newline at end of file diff --git a/hw/bsp/imxrt/boards/mimxrt1060_evk/board.cmake b/hw/bsp/imxrt/boards/mimxrt1060_evk/board.cmake index 033f9fcf9..171d427de 100644 --- a/hw/bsp/imxrt/boards/mimxrt1060_evk/board.cmake +++ b/hw/bsp/imxrt/boards/mimxrt1060_evk/board.cmake @@ -2,6 +2,7 @@ set(MCU_VARIANT MIMXRT1062) set(JLINK_DEVICE MIMXRT1062xxx6A) set(PYOCD_TARGET mimxrt1060) +set(NXPLS_DEVICE MIMXRT1062xxxxA:EVK-MIMXRT1060) function(update_board TARGET) target_sources(${TARGET} PUBLIC diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index e9615a1f4..e38bcf4b1 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -121,15 +121,26 @@ function(family_configure_target TARGET) # Link dependencies target_link_libraries(${TARGET} PUBLIC ${BOARD_TARGET} ${TARGET}-tinyusb) - # Flash Target + # group target (not yet supported by clion) + set_target_properties(${TARGET}-tinyusb ${TARGET}-tinyusb_config + PROPERTIES FOLDER ${TARGET}_sub + ) + + #---------- Flash ---------- + # Flash using pyocd add_custom_target(${TARGET}-pyocd COMMAND pyocd flash -t ${PYOCD_TARGET} $ ) - # group target - set_target_properties(${TARGET}-tinyusb ${TARGET}-tinyusb_config - PROPERTIES FOLDER ${TARGET}_sub + # Flash using NXP LinkServer (redlink) + # https://www.nxp.com/design/software/development-software/mcuxpresso-software-and-tools-/linkserver-for-microcontrollers:LINKERSERVER + # LinkServer has a bug that can only execute with full path otherwise it throws: + # realpath error: No such file or directory + execute_process(COMMAND which LinkServer OUTPUT_VARIABLE LINKSERVER_PATH OUTPUT_STRIP_TRAILING_WHITESPACE) + add_custom_target(${TARGET}-redlink + COMMAND ${LINKSERVER_PATH} flash ${NXPLS_DEVICE} load $ ) + endfunction() diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 9951aa5da..494e2e50f 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -79,7 +79,8 @@ typedef struct ehci_qhd_t qhd_pool[QHD_MAX]; ehci_qtd_t qtd_pool[QTD_MAX] TU_ATTR_ALIGNED(32); - ehci_registers_t* regs; + ehci_registers_t* regs; // operational register + ehci_cap_registers_t* cap_regs; // capability register volatile uint32_t uframe_number; }ehci_data_t; @@ -87,6 +88,26 @@ typedef struct // Periodic frame list must be 4K alignment CFG_TUH_MEM_SECTION TU_ATTR_ALIGNED(4096) static ehci_data_t ehci_data; +//--------------------------------------------------------------------+ +// Debug +//--------------------------------------------------------------------+ +#if CFG_TUSB_DEBUG >= EHCI_DBG +static inline void print_portsc(ehci_registers_t* regs) +{ + TU_LOG_HEX(EHCI_DBG, regs->portsc); + TU_LOG(EHCI_DBG, " Current Connect Status: %u\r\n", regs->portsc_bm.current_connect_status); + TU_LOG(EHCI_DBG, " Connect Status Change : %u\r\n", regs->portsc_bm.connect_status_change); + TU_LOG(EHCI_DBG, " Port Enabled : %u\r\n", regs->portsc_bm.port_enabled); + TU_LOG(EHCI_DBG, " Port Enabled Change : %u\r\n", regs->portsc_bm.port_enable_change); + + TU_LOG(EHCI_DBG, " Port Reset : %u\r\n", regs->portsc_bm.port_reset); + TU_LOG(EHCI_DBG, " Port Power : %u\r\n", regs->portsc_bm.port_power); +} + +#else +#define print_portsc(_reg) +#endif + //--------------------------------------------------------------------+ // PROTOTYPE //--------------------------------------------------------------------+ @@ -152,11 +173,11 @@ void hcd_port_reset(uint8_t rhport) ehci_registers_t* regs = ehci_data.regs; -// regs->portsc_bm.port_enabled = 0; // disable port before reset -// regs->portsc_bm.port_reset = 1; - - uint32_t portsc = regs->portsc; + // mask out all change bits since they are Write 1 to clear + uint32_t portsc = regs->portsc & ~EHCI_PORTSC_MASK_CHANGE_ALL; + // EHCI Table 2-16 PortSC + // when software writes Port Reset bit to a one, it must also write a zero to the Port Enable bit. portsc &= ~(EHCI_PORTSC_MASK_PORT_EANBLED); portsc |= EHCI_PORTSC_MASK_PORT_RESET; @@ -167,9 +188,14 @@ void hcd_port_reset_end(uint8_t rhport) { (void) rhport; -#if 0 +#if 0 // TODO check if this is necessary ehci_registers_t* regs = ehci_data.regs; - regs->portsc_bm.port_reset = 0; + + // mask out all change bits since they are Write 1 to clear + uint32_t portsc = regs->portsc & ~EHCI_PORTSC_MASK_CHANGE_ALL; + portsc &= ~(EHCI_PORTSC_MASK_PORT_RESET); + + regs->portsc = portsc; #endif } @@ -240,19 +266,26 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) { - (void) capability_reg; // not used yet - tu_memclr(&ehci_data, sizeof(ehci_data_t)); - ehci_data.regs = (ehci_registers_t* ) operatial_reg; + ehci_data.regs = (ehci_registers_t*) operatial_reg; + ehci_data.cap_regs = (ehci_cap_registers_t*) capability_reg; ehci_registers_t* regs = ehci_data.regs; + // EHCI 4.1 Host Controller Initialization + //------------- CTRLDSSEGMENT Register (skip) -------------// + //------------- USB INT Register -------------// - regs->inten = 0; // 1. disable all the interrupt - regs->status = EHCI_INT_MASK_ALL; // 2. clear all status + // disable all the interrupt + regs->inten = 0; + + // clear all status except port change since device maybe connected before this driver is initialized + regs->status = (EHCI_INT_MASK_ALL & ~EHCI_INT_MASK_PORT_CHANGE); + + // Enable interrupts regs->inten = EHCI_INT_MASK_ERROR | EHCI_INT_MASK_PORT_CHANGE | EHCI_INT_MASK_ASYNC_ADVANCE | EHCI_INT_MASK_NXP_PERIODIC | EHCI_INT_MASK_NXP_ASYNC | EHCI_INT_MASK_FRAMELIST_ROLLOVER; @@ -316,7 +349,16 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) FRAMELIST_SIZE_USBCMD_VALUE; //------------- ConfigFlag Register (skip) -------------// - regs->portsc_bm.port_power = 1; // enable port power + + // enable port power bit in portsc. The function of this bit depends on the value of the Port + // Power Control (PPC) field in the HCSPARAMS register. + if (ehci_data.cap_regs->hcsparams_bm.port_power_control) { + // mask out all change bits since they are Write 1 to clear + uint32_t portsc = (regs->portsc & ~EHCI_PORTSC_MASK_CHANGE_ALL); + portsc |= ECHI_PORTSC_MASK_PORT_POWER; + + regs->portsc = portsc; + } return true; } @@ -656,26 +698,6 @@ static void xfer_error_isr(uint8_t hostid) } } -#if CFG_TUSB_DEBUG >= EHCI_DBG - -static inline void print_portsc(ehci_registers_t* regs) -{ - TU_LOG_HEX(EHCI_DBG, regs->portsc); - TU_LOG(EHCI_DBG, " Current Connect Status: %u\r\n", regs->portsc_bm.current_connect_status); - TU_LOG(EHCI_DBG, " Connect Status Change : %u\r\n", regs->portsc_bm.connect_status_change); - TU_LOG(EHCI_DBG, " Port Enabled : %u\r\n", regs->portsc_bm.port_enabled); - TU_LOG(EHCI_DBG, " Port Enabled Change : %u\r\n", regs->portsc_bm.port_enable_change); - - TU_LOG(EHCI_DBG, " Port Reset : %u\r\n", regs->portsc_bm.port_reset); - TU_LOG(EHCI_DBG, " Port Power : %u\r\n", regs->portsc_bm.port_power); -} - -#else - -#define print_portsc(_reg) - -#endif - //------------- Host Controller Driver's Interrupt Handler -------------// void hcd_int_handler(uint8_t rhport) { @@ -695,7 +717,7 @@ void hcd_int_handler(uint8_t rhport) if (int_status & EHCI_INT_MASK_PORT_CHANGE) { - uint32_t const port_status = regs->portsc & EHCI_PORTSC_MASK_ALL; + uint32_t const port_status = regs->portsc & EHCI_PORTSC_MASK_CHANGE_ALL; print_portsc(regs); if (regs->portsc_bm.connect_status_change) diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index 36f8649be..dd090cb36 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -267,16 +267,15 @@ TU_VERIFY_STATIC( sizeof(ehci_sitd_t) == 32, "size is not correct" ); //--------------------------------------------------------------------+ // EHCI Operational Register //--------------------------------------------------------------------+ -enum ehci_interrupt_mask_{ +enum { EHCI_INT_MASK_USB = TU_BIT(0), EHCI_INT_MASK_ERROR = TU_BIT(1), EHCI_INT_MASK_PORT_CHANGE = TU_BIT(2), - EHCI_INT_MASK_FRAMELIST_ROLLOVER = TU_BIT(3), EHCI_INT_MASK_PCI_HOST_SYSTEM_ERROR = TU_BIT(4), EHCI_INT_MASK_ASYNC_ADVANCE = TU_BIT(5), - EHCI_INT_MASK_NXP_SOF = TU_BIT(7), + EHCI_INT_MASK_NXP_SOF = TU_BIT(7), EHCI_INT_MASK_NXP_ASYNC = TU_BIT(18), EHCI_INT_MASK_NXP_PERIODIC = TU_BIT(19), @@ -287,7 +286,7 @@ enum ehci_interrupt_mask_{ EHCI_INT_MASK_NXP_ASYNC | EHCI_INT_MASK_NXP_PERIODIC }; -enum ehci_usbcmd_pos_ { +enum { EHCI_USBCMD_POS_RUN_STOP = 0, EHCI_USBCMD_POS_FRAMELIST_SIZE = 2, EHCI_USBCMD_POS_PERIOD_ENABLE = 4, @@ -296,24 +295,27 @@ enum ehci_usbcmd_pos_ { EHCI_USBCMD_POS_INTERRUPT_THRESHOLD = 16 }; -enum ehci_portsc_change_mask_{ +enum { EHCI_PORTSC_MASK_CURRENT_CONNECT_STATUS = TU_BIT(0), EHCI_PORTSC_MASK_CONNECT_STATUS_CHANGE = TU_BIT(1), EHCI_PORTSC_MASK_PORT_EANBLED = TU_BIT(2), - EHCI_PORTSC_MASK_PORT_ENABLE_CHAGNE = TU_BIT(3), + EHCI_PORTSC_MASK_PORT_ENABLE_CHANGE = TU_BIT(3), EHCI_PORTSC_MASK_OVER_CURRENT_CHANGE = TU_BIT(5), + EHCI_PORTSC_MASK_FORCE_RESUME = TU_BIT(6), + EHCI_PORTSC_MASK_PORT_SUSPEND = TU_BIT(7), EHCI_PORTSC_MASK_PORT_RESET = TU_BIT(8), + ECHI_PORTSC_MASK_PORT_POWER = TU_BIT(12), - EHCI_PORTSC_MASK_ALL = - EHCI_PORTSC_MASK_CONNECT_STATUS_CHANGE | - EHCI_PORTSC_MASK_PORT_ENABLE_CHAGNE | - EHCI_PORTSC_MASK_OVER_CURRENT_CHANGE + EHCI_PORTSC_MASK_CHANGE_ALL = + EHCI_PORTSC_MASK_CONNECT_STATUS_CHANGE | + EHCI_PORTSC_MASK_PORT_ENABLE_CHANGE | + EHCI_PORTSC_MASK_OVER_CURRENT_CHANGE }; typedef volatile struct { union { - uint32_t command; + uint32_t command; // 0x00 struct { uint32_t run_stop : 1 ; ///< 1=Run. 0=Stop @@ -333,7 +335,7 @@ typedef volatile struct }; union { - uint32_t status; + uint32_t status; // 0x04 struct { uint32_t usb : 1 ; ///< qTD with IOC is retired @@ -357,7 +359,7 @@ typedef volatile struct }; union{ - uint32_t inten; + uint32_t inten; // 0x08 struct { uint32_t usb : 1 ; @@ -375,43 +377,87 @@ typedef volatile struct }inten_bm; }; - uint32_t frame_index ; ///< Micro frame counter - uint32_t ctrl_ds_seg ; ///< Control Data Structure Segment - uint32_t periodic_list_base ; ///< Beginning address of perodic frame list - uint32_t async_list_addr ; ///< Address of next async QHD to be executed + uint32_t frame_index ; ///< 0x0C Micro frame counter + uint32_t ctrl_ds_seg ; ///< 0x10 Control Data Structure Segment + uint32_t periodic_list_base ; ///< 0x14 Beginning address of perodic frame list + uint32_t async_list_addr ; ///< 0x18 Address of next async QHD to be executed uint32_t nxp_tt_control ; ///< nxp embedded transaction translator (reserved by EHCI specs) uint32_t reserved[8] ; - uint32_t config_flag ; ///< not used by NXP + uint32_t config_flag ; ///< 0x40 not used by NXP union { - uint32_t portsc ; ///< port status and control - struct { - uint32_t current_connect_status : 1; ///< 0: No device, 1: Device is present on port - uint32_t connect_status_change : 1; ///< Change in Current Connect Status - uint32_t port_enabled : 1; ///< Ports can only be enabled by HC as a part of the reset and enable. SW can write 0 to disable - uint32_t port_enable_change : 1; ///< Port Enabled has changed - uint32_t over_current_active : 1; ///< Port has an over-current condition - uint32_t over_current_change : 1; ///< Change to Over-current Active - uint32_t force_port_resume : 1; ///< Resume detected/driven on port. This functionality defined for manipulating this bit depends on the value of the Suspend bit. - uint32_t suspend : 1; ///< Port in suspend state - uint32_t port_reset : 1; ///< 1=Port is in Reset. 0=Port is not in Reset - uint32_t nxp_highspeed_status : 1; ///< NXP customized: 0=connected to the port is not in High-speed mode, 1=connected to the port is in High-speed mode - uint32_t line_status : 2; ///< D+/D- state: 00: SE0, 10: J-state, 01: K-state - uint32_t port_power : 1; ///< 0= power off, 1= power on - uint32_t port_owner : 1; ///< not used by NXP - uint32_t port_indicator_control : 2; ///< 00b: off, 01b: Amber, 10b: green, 11b: undefined - uint32_t port_test_control : 4; ///< Port test mode, not used by tinyusb - uint32_t wake_on_connect_enable : 1; ///< Enables device connects as wake-up events - uint32_t wake_on_disconnect_enable : 1; ///< Enables device disconnects as wake-up events - uint32_t wake_on_over_current_enable : 1; ///< Enables over-current conditions as wake-up events - uint32_t nxp_phy_clock_disable : 1; ///< NXP customized: the PHY can be put into Low Power Suspend – Clock Disable when the downstream device has been put into suspend mode or when no downstream device is connected. Low power suspend is completely under the control of software. 0: enable PHY clock, 1: disable PHY clock - uint32_t nxp_port_force_fullspeed : 1; ///< NXP customized: Writing this bit to a 1 will force the port to only connect at Full Speed. It disables the chirp sequence that allowsthe port to identify itself as High Speed. This is useful for testing FS configurations with a HS host, hub or device. - uint32_t TU_RESERVED : 1; - uint32_t nxp_port_speed : 2; ///< NXP customized: This register field indicates the speed atwhich the port is operating. For HS mode operation in the host controllerand HS/FS operation in the device controller the port routing steers data to the Protocol engine. For FS and LS mode operation in the host controller, the port routing steers data to the Protocol Engine w/ Embedded Transaction Translator. 0x0: Fullspeed, 0x1: Lowspeed, 0x2: Highspeed + // mixed with RW and R/WC bits, care should be taken when writing to this register + uint32_t portsc ; ///< 0x44 port status and control + const struct { + uint32_t current_connect_status : 1; ///< 00: 0: No device, 1: Device is present on port + uint32_t connect_status_change : 1; ///< 01: [R/WC] Change in Current Connect Status + uint32_t port_enabled : 1; ///< 02: Ports can only be enabled by HC as a part of the reset and enable. SW can write 0 to disable + uint32_t port_enable_change : 1; ///< 03: [R/WC] Port Enabled has changed + uint32_t over_current_active : 1; ///< 04: Port has an over-current condition + uint32_t over_current_change : 1; ///< 05: [R/WC] Change to Over-current Active + uint32_t force_port_resume : 1; ///< 06: Resume detected/driven on port. This functionality defined for manipulating this bit depends on the value of the Suspend bit. + uint32_t suspend : 1; ///< 07: Port in suspend state + uint32_t port_reset : 1; ///< 08: 1=Port is in Reset. 0=Port is not in Reset + uint32_t nxp_highspeed_status : 1; ///< 09: NXP customized: 0=connected to the port is not in High-speed mode, 1=connected to the port is in High-speed mode + uint32_t line_status : 2; ///< 10-11: D+/D- state: 00: SE0, 10: J-state, 01: K-state + uint32_t port_power : 1; ///< 12: 0= power off, 1= power on + uint32_t port_owner : 1; ///< 13: not used by NXP + uint32_t port_indicator_control : 2; ///< 14-15: 00b: off, 01b: Amber, 10b: green, 11b: undefined + uint32_t port_test_control : 4; ///< 16-19: Port test mode, not used by tinyusb + uint32_t wake_on_connect_enable : 1; ///< 20: Enables device connects as wake-up events + uint32_t wake_on_disconnect_enable : 1; ///< 21: Enables device disconnects as wake-up events + uint32_t wake_on_over_current_enable : 1; ///< 22: Enables over-current conditions as wake-up events + uint32_t nxp_phy_clock_disable : 1; ///< 23: NXP customized: the PHY can be put into Low Power Suspend – Clock Disable when the downstream device has been put into suspend mode or when no downstream device is connected. Low power suspend is completely under the control of software. 0: enable PHY clock, 1: disable PHY clock + uint32_t nxp_port_force_fullspeed : 1; ///< 24: NXP customized: Writing this bit to a 1 will force the port to only connect at Full Speed. It disables the chirp sequence that allowsthe port to identify itself as High Speed. This is useful for testing FS configurations with a HS host, hub or device. + uint32_t TU_RESERVED : 1; ///< 25 + uint32_t nxp_port_speed : 2; ///< 26-27: NXP customized: This register field indicates the speed atwhich the port is operating. For HS mode operation in the host controllerand HS/FS operation in the device controller the port routing steers data to the Protocol engine. For FS and LS mode operation in the host controller, the port routing steers data to the Protocol Engine w/ Embedded Transaction Translator. 0x0: Fullspeed, 0x1: Lowspeed, 0x2: Highspeed uint32_t TU_RESERVED : 4; }portsc_bm; }; -}ehci_registers_t; +} ehci_registers_t; + +//--------------------------------------------------------------------+ +// Capability Registers +//--------------------------------------------------------------------+ +typedef volatile struct { + uint8_t caplength; // 0x00 + uint8_t TU_RESERVED; // 0x01 + uint16_t hciversion; // 0x02 + + union { + uint32_t hcsparams; // 0x04 + struct { + uint32_t num_ports : 4; // [00:03] + uint32_t port_power_control : 1; // [04] + uint32_t TU_RESERVED : 2; // [05:06] + uint32_t port_route_rule : 1; // [07] + uint32_t n_pcc : 4; // [08:11] Number of Ports per Companion Controller + uint32_t n_cc : 4; // [12:15] Number of Companion Controllers + uint32_t port_ind : 1; // [16] Port Indicators + uint32_t TU_RESERVED : 3; // [17:19] + uint32_t n_ptt : 4; // [20:23] ChipIdea: Number of Ports per Transaction Translator + uint32_t n_tt : 4; // [24:27] ChipIdea: Number of Transaction Translators + uint32_t TU_RESERVED : 4; // [28:31] + } hcsparams_bm; + }; + + union { + uint32_t hccparams; // 0x08 + struct { + uint32_t addr_64bit : 1; // [00] 64-bit Addressing Capability + uint32_t programmable_frame_list_flag : 1; // [01] Programmable Frame List Flag + uint32_t async_park_cap : 1; // [02] Asynchronous Schedule Park Capability + uint32_t TU_RESERVED : 1; // [03] + uint32_t iso_schedule_threshold : 4; // [4:7] Isochronous Scheduling Threshold + uint32_t eecp : 8; // [8:15] EHCI Extended Capabilities Pointer + uint32_t TU_RESERVED : 16;// [16:31] + } hccparams_bm; + }; + + uint32_t hcsp_portroute; // 0x0C HCSP Port Route Register +} ehci_cap_registers_t; + +TU_VERIFY_STATIC(sizeof(ehci_cap_registers_t) == 16, "size is not correct"); #ifdef __cplusplus } -- cgit v1.3.1 From c0e4c02b9d70240b97aa4924e6002ccb3d8057dd Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 10 May 2023 11:15:11 +0700 Subject: allow imxrt build with dual exmaples --- examples/cmake/toolchain/set_flags.cmake | 3 ++- examples/dual/CMakeLists.txt | 11 +++++---- .../dual/host_hid_to_device_cdc/CMakeLists.txt | 28 +++++++++++----------- hw/bsp/family_support.cmake | 4 ++-- hw/bsp/imxrt/family.cmake | 4 ++++ src/portable/chipidea/ci_hs/hcd_ci_hs.c | 2 ++ 6 files changed, 30 insertions(+), 22 deletions(-) (limited to 'src/portable') diff --git a/examples/cmake/toolchain/set_flags.cmake b/examples/cmake/toolchain/set_flags.cmake index 27631abcd..3f109b59e 100644 --- a/examples/cmake/toolchain/set_flags.cmake +++ b/examples/cmake/toolchain/set_flags.cmake @@ -8,7 +8,8 @@ foreach(LANG IN ITEMS C CXX ASM) #cmake_print_variables(CMAKE_${LANG}_FLAGS_INIT) # optimization flags - set(CMAKE_${LANG}_FLAGS_DEBUG_INIT "-Og") + set(CMAKE_${LANG}_FLAGS_RELEASE_INIT "-Os") + set(CMAKE_${LANG}_FLAGS_DEBUG_INIT "-O0") endforeach() # Linker diff --git a/examples/dual/CMakeLists.txt b/examples/dual/CMakeLists.txt index d211c8b83..15081cf26 100644 --- a/examples/dual/CMakeLists.txt +++ b/examples/dual/CMakeLists.txt @@ -4,9 +4,10 @@ include(${CMAKE_CURRENT_SOURCE_DIR}/../../hw/bsp/family_support.cmake) project(tinyusb_dual_examples C CXX ASM) family_initialize_project(tinyusb_dual_examples ${CMAKE_CURRENT_LIST_DIR}) + if (FAMILY STREQUAL "rp2040" AND NOT TARGET tinyusb_pico_pio_usb) - message("Skipping dual host/device mode examples as Pico-PIO-USB is not available") -else() - # family_add_subdirectory will filter what to actually add based on selected FAMILY - family_add_subdirectory(host_hid_to_device_cdc) -endif() + message("Skipping dual host/device mode examples as Pico-PIO-USB is not available") +else () + # family_add_subdirectory will filter what to actually add based on selected FAMILY + family_add_subdirectory(host_hid_to_device_cdc) +endif () diff --git a/examples/dual/host_hid_to_device_cdc/CMakeLists.txt b/examples/dual/host_hid_to_device_cdc/CMakeLists.txt index 3505d39eb..c6d19a720 100644 --- a/examples/dual/host_hid_to_device_cdc/CMakeLists.txt +++ b/examples/dual/host_hid_to_device_cdc/CMakeLists.txt @@ -14,14 +14,14 @@ add_executable(${PROJECT}) # Example source target_sources(${PROJECT} PUBLIC - ${CMAKE_CURRENT_SOURCE_DIR}/src/main.c - ${CMAKE_CURRENT_SOURCE_DIR}/src/usb_descriptors.c - ) + ${CMAKE_CURRENT_SOURCE_DIR}/src/main.c + ${CMAKE_CURRENT_SOURCE_DIR}/src/usb_descriptors.c + ) # Example include target_include_directories(${PROJECT} PUBLIC - ${CMAKE_CURRENT_SOURCE_DIR}/src - ) + ${CMAKE_CURRENT_SOURCE_DIR}/src + ) # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. @@ -29,12 +29,12 @@ family_configure_dual_usb_example(${PROJECT}) # due to warnings from Pico-PIO-USB target_compile_options(${PROJECT} PUBLIC - -Wno-error=shadow - -Wno-error=cast-align - -Wno-error=cast-qual - -Wno-error=redundant-decls - -Wno-error=sign-conversion - -Wno-error=conversion - -Wno-error=sign-compare - -Wno-error=unused-function - ) + -Wno-error=shadow + -Wno-error=cast-align + -Wno-error=cast-qual + -Wno-error=redundant-decls + -Wno-error=sign-conversion + -Wno-error=conversion + -Wno-error=sign-compare + -Wno-error=unused-function + ) diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index 26baa6365..01e7bb018 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -27,8 +27,8 @@ if (NOT TARGET _family_support_marker) foreach(MCU IN LISTS FAMILY_MCUS) # For each line in only.txt foreach(_line ${ONLYS_LINES}) - # If mcu:xxx exists for this mcu then include - if (${_line} STREQUAL "mcu:${MCU}") + # If mcu:xxx exists for this mcu or board:xxx then include + if (${_line} STREQUAL "mcu:${MCU}" OR ${_line} STREQUAL "board:${BOARD}") set(${RESULT} 1 PARENT_SCOPE) return() endif() diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index 85ad104a0..b510c064e 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -173,3 +173,7 @@ endfunction() function(family_configure_host_example TARGET) family_configure_target(${TARGET}) endfunction() + +function(family_configure_dual_usb_example TARGET) + family_configure_target(${TARGET}) +endfunction() diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index d607627b4..b06633f30 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -76,6 +76,8 @@ bool hcd_init(uint8_t rhport) #endif // FIXME force full speed, still have issue with Highspeed enumeration + // 1. Have issue when plug/unplug devices, maybe the port is not reset properly + // 2. Also does not seems to detect disconnection hcd_reg->PORTSC1 |= PORTSC1_FORCE_FULL_SPEED; return ehci_init(rhport, (uint32_t) &hcd_reg->CAPLENGTH, (uint32_t) &hcd_reg->USBCMD); -- cgit v1.3.1 From 206d63e038744b228cfa6051d701cab50b520fe6 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 11 May 2023 14:26:12 +0700 Subject: correct EHCI reporting failed xfer (instead of stalled) when device is unplugged --- src/class/cdc/cdc_host.c | 21 +++++++++++---------- src/class/hid/hid_host.c | 27 ++++++++++++++++----------- src/class/msc/msc_host.c | 10 +++++++--- src/common/tusb_debug.h | 1 + src/device/usbd_control.c | 9 ++++++--- src/host/hub.c | 9 ++++++++- src/host/usbh.c | 20 +++++++++++++------- src/portable/ehci/ehci.c | 11 ++++++++--- src/tusb.c | 4 ++++ 9 files changed, 74 insertions(+), 38 deletions(-) (limited to 'src/portable') diff --git a/src/class/cdc/cdc_host.c b/src/class/cdc/cdc_host.c index fe3691bf4..9ff666ed4 100644 --- a/src/class/cdc/cdc_host.c +++ b/src/class/cdc/cdc_host.c @@ -35,8 +35,7 @@ // Debug level, TUSB_CFG_DEBUG must be at least this level for debug message #define CDCH_DEBUG 2 - -#define TU_LOG_CDCH(...) TU_LOG(CDCH_DEBUG, __VA_ARGS__) +#define TU_LOG_DRV(...) TU_LOG(CDCH_DEBUG, __VA_ARGS__) //--------------------------------------------------------------------+ // Host CDC Interface @@ -537,6 +536,8 @@ void cdch_close(uint8_t daddr) cdch_interface_t* p_cdc = &cdch_data[idx]; if (p_cdc->daddr == daddr) { + TU_LOG_DRV(" CDCh close addr = %u index = %u\r\n", daddr, idx); + // Invoke application callback if (tuh_cdc_umount_cb) tuh_cdc_umount_cb(idx); @@ -804,7 +805,7 @@ static void acm_process_config(tuh_xfer_t* xfer) static bool acm_set_control_line_state(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { TU_VERIFY(p_cdc->acm_capability.support_line_request); - TU_LOG_CDCH("CDC ACM Set Control Line State\r\n"); + TU_LOG_DRV("CDC ACM Set Control Line State\r\n"); tusb_control_request_t const request = { .bmRequestType_bit = { @@ -834,7 +835,7 @@ static bool acm_set_control_line_state(cdch_interface_t* p_cdc, uint16_t line_st } static bool acm_set_line_coding(cdch_interface_t* p_cdc, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { - TU_LOG_CDCH("CDC ACM Set Line Conding\r\n"); + TU_LOG_DRV("CDC ACM Set Line Conding\r\n"); tusb_control_request_t const request = { .bmRequestType_bit = { @@ -894,7 +895,7 @@ static bool ftdi_open(uint8_t daddr, const tusb_desc_interface_t *itf_desc, uint cdch_interface_t * p_cdc = make_new_itf(daddr, itf_desc); TU_VERIFY(p_cdc); - TU_LOG_CDCH("FTDI opened\r\n"); + TU_LOG_DRV("FTDI opened\r\n"); p_cdc->serial_drid = SERIAL_DRIVER_FTDI; @@ -938,7 +939,7 @@ static bool ftdi_sio_reset(cdch_interface_t* p_cdc, tuh_xfer_cb_t complete_cb, u static bool ftdi_sio_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { - TU_LOG_CDCH("CDC FTDI Set Control Line State\r\n"); + TU_LOG_DRV("CDC FTDI Set Control Line State\r\n"); p_cdc->user_control_cb = complete_cb; TU_ASSERT(ftdi_sio_set_request(p_cdc, FTDI_SIO_MODEM_CTRL, 0x0300 | line_state, complete_cb ? cdch_internal_control_complete : NULL, user_data)); @@ -974,7 +975,7 @@ static uint32_t ftdi_232bm_baud_to_divisor(uint32_t baud) static bool ftdi_sio_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { uint16_t const divisor = (uint16_t) ftdi_232bm_baud_to_divisor(baudrate); - TU_LOG_CDCH("CDC FTDI Set BaudRate = %lu, divisor = 0x%04x\n", baudrate, divisor); + TU_LOG_DRV("CDC FTDI Set BaudRate = %lu, divisor = 0x%04x\n", baudrate, divisor); p_cdc->user_control_cb = complete_cb; _ftdi_requested_baud = baudrate; @@ -1061,7 +1062,7 @@ static bool cp210x_open(uint8_t daddr, tusb_desc_interface_t const *itf_desc, ui cdch_interface_t * p_cdc = make_new_itf(daddr, itf_desc); TU_VERIFY(p_cdc); - TU_LOG_CDCH("CP210x opened\r\n"); + TU_LOG_DRV("CP210x opened\r\n"); p_cdc->serial_drid = SERIAL_DRIVER_CP210X; // endpoint pair @@ -1109,7 +1110,7 @@ static bool cp210x_ifc_enable(cdch_interface_t* p_cdc, uint16_t enabled, tuh_xfe } static bool cp210x_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { - TU_LOG_CDCH("CDC CP210x Set BaudRate = %lu\n", baudrate); + TU_LOG_DRV("CDC CP210x Set BaudRate = %lu\n", baudrate); uint32_t baud_le = tu_htole32(baudrate); p_cdc->user_control_cb = complete_cb; return cp210x_set_request(p_cdc, CP210X_SET_BAUDRATE, 0, (uint8_t *) &baud_le, 4, @@ -1118,7 +1119,7 @@ static bool cp210x_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_ static bool cp210x_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { - TU_LOG_CDCH("CDC CP210x Set Control Line State\r\n"); + TU_LOG_DRV("CDC CP210x Set Control Line State\r\n"); p_cdc->user_control_cb = complete_cb; return cp210x_set_request(p_cdc, CP210X_SET_MHS, 0x0300 | line_state, NULL, 0, complete_cb ? cdch_internal_control_complete : NULL, user_data); diff --git a/src/class/hid/hid_host.c b/src/class/hid/hid_host.c index d95d3ef35..3a491937a 100644 --- a/src/class/hid/hid_host.c +++ b/src/class/hid/hid_host.c @@ -33,6 +33,10 @@ #include "hid_host.h" +// Debug level, TUSB_CFG_DEBUG must be at least this level for debug message +#define HIDH_DEBUG 2 +#define TU_LOG_DRV(...) TU_LOG(HIDH_DEBUG, __VA_ARGS__) + //--------------------------------------------------------------------+ // MACRO CONSTANT TYPEDEF //--------------------------------------------------------------------+ @@ -207,7 +211,7 @@ static void set_protocol_complete(tuh_xfer_t* xfer) static bool _hidh_set_protocol(uint8_t daddr, uint8_t itf_num, uint8_t protocol, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { - TU_LOG2("HID Set Protocol = %d\r\n", protocol); + TU_LOG_DRV("HID Set Protocol = %d\r\n", protocol); tusb_control_request_t const request = { @@ -246,7 +250,7 @@ bool tuh_hid_set_protocol(uint8_t daddr, uint8_t idx, uint8_t protocol) static void set_report_complete(tuh_xfer_t* xfer) { - TU_LOG2("HID Set Report complete\r\n"); + TU_LOG_DRV("HID Set Report complete\r\n"); if (tuh_hid_set_report_complete_cb) { @@ -266,7 +270,7 @@ bool tuh_hid_set_report(uint8_t daddr, uint8_t idx, uint8_t report_id, uint8_t r hidh_interface_t* p_hid = get_hid_itf(daddr, idx); TU_VERIFY(p_hid); - TU_LOG2("HID Set Report: id = %u, type = %u, len = %u\r\n", report_id, report_type, len); + TU_LOG_DRV("HID Set Report: id = %u, type = %u, len = %u\r\n", report_id, report_type, len); tusb_control_request_t const request = { @@ -298,7 +302,7 @@ bool tuh_hid_set_report(uint8_t daddr, uint8_t idx, uint8_t report_id, uint8_t r static bool _hidh_set_idle(uint8_t daddr, uint8_t itf_num, uint16_t idle_rate, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { // SET IDLE request, device can stall if not support this request - TU_LOG2("HID Set Idle \r\n"); + TU_LOG_DRV("HID Set Idle \r\n"); tusb_control_request_t const request = { @@ -367,7 +371,7 @@ bool tuh_hid_send_ready(uint8_t dev_addr, uint8_t idx) bool tuh_hid_send_report(uint8_t daddr, uint8_t idx, uint8_t report_id, const void* report, uint16_t len) { - TU_LOG2("HID Send Report %d\r\n", report_id); + TU_LOG_DRV("HID Send Report %d\r\n", report_id); hidh_interface_t* p_hid = get_hid_itf(daddr, idx); TU_VERIFY(p_hid); @@ -430,7 +434,7 @@ bool hidh_xfer_cb(uint8_t daddr, uint8_t ep_addr, xfer_result_t result, uint32_t if ( dir == TUSB_DIR_IN ) { - TU_LOG2(" Get Report callback (%u, %u)\r\n", daddr, idx); + TU_LOG_DRV(" Get Report callback (%u, %u)\r\n", daddr, idx); TU_LOG3_MEM(p_hid->epin_buf, xferred_bytes, 2); tuh_hid_report_received_cb(daddr, idx, p_hid->epin_buf, (uint16_t) xferred_bytes); }else @@ -448,8 +452,9 @@ void hidh_close(uint8_t daddr) hidh_interface_t* p_hid = &_hidh_itf[i]; if (p_hid->daddr == daddr) { - if(tuh_hid_umount_cb) tuh_hid_umount_cb(daddr, i); - p_hid->daddr = 0; + TU_LOG_DRV(" HIDh close addr = %u index = %u\r\n", daddr, i); + if(tuh_hid_umount_cb) tuh_hid_umount_cb(daddr, i); + p_hid->daddr = 0; } } } @@ -465,7 +470,7 @@ bool hidh_open(uint8_t rhport, uint8_t daddr, tusb_desc_interface_t const *desc_ TU_VERIFY(TUSB_CLASS_HID == desc_itf->bInterfaceClass); - TU_LOG2("[%u] HID opening Interface %u\r\n", daddr, desc_itf->bInterfaceNumber); + TU_LOG_DRV("[%u] HID opening Interface %u\r\n", daddr, desc_itf->bInterfaceNumber); // len = interface + hid + n*endpoints uint16_t const drv_len = (uint16_t) (sizeof(tusb_desc_interface_t) + sizeof(tusb_hid_descriptor_hid_t) + @@ -592,7 +597,7 @@ static void process_set_config(tuh_xfer_t* xfer) // using usbh enumeration buffer since report descriptor can be very long if( p_hid->report_desc_len > CFG_TUH_ENUMERATION_BUFSIZE ) { - TU_LOG2("HID Skip Report Descriptor since it is too large %u bytes\r\n", p_hid->report_desc_len); + TU_LOG_DRV("HID Skip Report Descriptor since it is too large %u bytes\r\n", p_hid->report_desc_len); // Driver is mounted without report descriptor config_driver_mount_complete(daddr, idx, NULL, 0); @@ -763,7 +768,7 @@ uint8_t tuh_hid_parse_report_descriptor(tuh_hid_report_info_t* report_info_arr, for ( uint8_t i = 0; i < report_num; i++ ) { info = report_info_arr+i; - TU_LOG2("%u: id = %u, usage_page = %u, usage = %u\r\n", i, info->report_id, info->usage_page, info->usage); + TU_LOG_DRV("%u: id = %u, usage_page = %u, usage = %u\r\n", i, info->report_id, info->usage_page, info->usage); } return report_num; diff --git a/src/class/msc/msc_host.c b/src/class/msc/msc_host.c index 1b48813ec..138443de4 100644 --- a/src/class/msc/msc_host.c +++ b/src/class/msc/msc_host.c @@ -35,7 +35,6 @@ // Debug level, TUSB_CFG_DEBUG must be at least this level for debug message #define MSCH_DEBUG 2 - #define TU_LOG_MSCH(...) TU_LOG(MSCH_DEBUG, __VA_ARGS__) //--------------------------------------------------------------------+ @@ -82,6 +81,7 @@ CFG_TUH_MEM_SECTION static msch_interface_t _msch_itf[CFG_TUH_DEVICE_MAX]; CFG_TUH_MEM_SECTION CFG_TUH_MEM_ALIGN static uint8_t _msch_buffer[sizeof(scsi_inquiry_resp_t)]; +// FIXME potential nul reference TU_ATTR_ALWAYS_INLINE static inline msch_interface_t* get_itf(uint8_t dev_addr) { @@ -305,11 +305,15 @@ void msch_init(void) void msch_close(uint8_t dev_addr) { TU_VERIFY(dev_addr <= CFG_TUH_DEVICE_MAX, ); - msch_interface_t* p_msc = get_itf(dev_addr); + TU_VERIFY(p_msc->configured, ); + + TU_LOG_MSCH(" MSCh close addr = %d\r\n", dev_addr); // invoke Application Callback - if (p_msc->mounted && tuh_msc_umount_cb) tuh_msc_umount_cb(dev_addr); + if (p_msc->mounted) { + if(tuh_msc_umount_cb) tuh_msc_umount_cb(dev_addr); + } tu_memclr(p_msc, sizeof(msch_interface_t)); } diff --git a/src/common/tusb_debug.h b/src/common/tusb_debug.h index 82f682043..36507041f 100644 --- a/src/common/tusb_debug.h +++ b/src/common/tusb_debug.h @@ -46,6 +46,7 @@ #if CFG_TUSB_DEBUG >= 2 extern char const* const tu_str_speed[]; extern char const* const tu_str_std_request[]; +extern char const* const tu_str_xfer_result[]; #endif void tu_print_mem(void const *buf, uint32_t count, uint8_t indent); diff --git a/src/device/usbd_control.c b/src/device/usbd_control.c index ea8eef285..2afe967b5 100644 --- a/src/device/usbd_control.c +++ b/src/device/usbd_control.c @@ -32,7 +32,10 @@ #include "tusb.h" #include "device/usbd_pvt.h" -#if CFG_TUSB_DEBUG >= 2 +// Debug level of USBD Control +#define USBD_CONTROL_DEBUG 2 + +#if CFG_TUSB_DEBUG >= USBD_CONTROL_DEBUG extern void usbd_driver_print_control_complete_name(usbd_control_xfer_cb_t callback); #endif @@ -188,7 +191,7 @@ bool usbd_control_xfer_cb (uint8_t rhport, uint8_t ep_addr, xfer_result_t result { TU_VERIFY(_ctrl_xfer.buffer); memcpy(_ctrl_xfer.buffer, _usbd_ctrl_buf, xferred_bytes); - TU_LOG_MEM(2, _usbd_ctrl_buf, xferred_bytes, 2); + TU_LOG_MEM(USBD_CONTROL_DEBUG, _usbd_ctrl_buf, xferred_bytes, 2); } _ctrl_xfer.total_xferred += (uint16_t) xferred_bytes; @@ -205,7 +208,7 @@ bool usbd_control_xfer_cb (uint8_t rhport, uint8_t ep_addr, xfer_result_t result // callback can still stall control in status phase e.g out data does not make sense if ( _ctrl_xfer.complete_cb ) { - #if CFG_TUSB_DEBUG >= 2 + #if CFG_TUSB_DEBUG >= USBD_CONTROL_DEBUG usbd_driver_print_control_complete_name(_ctrl_xfer.complete_cb); #endif diff --git a/src/host/hub.c b/src/host/hub.c index 386ad6aae..85bf22b3e 100644 --- a/src/host/hub.c +++ b/src/host/hub.c @@ -33,6 +33,10 @@ #include "usbh_classdriver.h" #include "hub.h" +// Debug level, TUSB_CFG_DEBUG must be at least this level for debug message +#define HUB_DEBUG 2 +#define TU_LOG_DRV(...) TU_LOG(HUB_DEBUG, __VA_ARGS__) + //--------------------------------------------------------------------+ // MACRO CONSTANT TYPEDEF //--------------------------------------------------------------------+ @@ -218,7 +222,10 @@ void hub_close(uint8_t dev_addr) TU_VERIFY(dev_addr > CFG_TUH_DEVICE_MAX, ); hub_interface_t* p_hub = get_itf(dev_addr); - if (p_hub->ep_in) tu_memclr(p_hub, sizeof( hub_interface_t)); + if (p_hub->ep_in) { + TU_LOG_DRV(" HUB close addr = %d\r\n", dev_addr); + tu_memclr(p_hub, sizeof( hub_interface_t)); + } } bool hub_edpt_status_xfer(uint8_t dev_addr) diff --git a/src/host/usbh.c b/src/host/usbh.c index 24ce47a7f..4cfc7c5c2 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -61,6 +61,8 @@ typedef struct uint8_t hub_addr; uint8_t hub_port; uint8_t speed; + + // enumeration is in progress, done when all interfaces are configured volatile uint8_t enumerating; // struct TU_ATTR_PACKED { @@ -436,7 +438,8 @@ void tuh_task_ext(uint32_t timeout_ms, bool in_isr) uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const ep_dir = tu_edpt_dir(ep_addr); - TU_LOG_USBH("on EP %02X with %u bytes\r\n", ep_addr, (unsigned int) event.xfer_complete.len); + TU_LOG_USBH("on EP %02X with %u bytes %s\r\n", ep_addr, (unsigned int) event.xfer_complete.len, + tu_str_xfer_result[event.xfer_complete.result]); if (event.dev_addr == 0) { @@ -866,6 +869,10 @@ TU_ATTR_FAST_FUNC void hcd_event_handler(hcd_event_t const* event, bool in_isr) { switch (event->event_id) { +// case HCD_EVENT_DEVICE_REMOVE: +// +// break; + default: osal_queue_send(_usbh_q, event, in_isr); break; @@ -1128,30 +1135,28 @@ static void process_device_unplugged(uint8_t rhport, uint8_t hub_addr, uint8_t h usbh_device_t* dev = &_usbh_devices[dev_id]; uint8_t const dev_addr = dev_id+1; - // TODO Hub multiple level if (dev->rhport == rhport && (hub_addr == 0 || dev->hub_addr == hub_addr) && // hub_addr = 0 means roothub (hub_port == 0 || dev->hub_port == hub_port) && // hub_port = 0 means all devices of downstream hub dev->connected) { - TU_LOG_USBH(" Address = %u\r\n", dev_addr); + TU_LOG_USBH("Device unplugged address = %u\r\n", dev_addr); if (is_hub_addr(dev_addr)) { - TU_LOG(USBH_DEBUG, "HUB address = %u is unmounted\r\n", dev_addr); + TU_LOG(USBH_DEBUG, " is a HUB device\r\n", dev_addr); // If the device itself is a usb hub, unplug downstream devices. // FIXME un-roll recursive calls to prevent potential stack overflow process_device_unplugged(rhport, dev_addr, 0); }else { - // Invoke callback before closing driver + // Invoke callback before closing driver (maybe call it later ?) if (tuh_umount_cb) tuh_umount_cb(dev_addr); } // Close class driver for (uint8_t drv_id = 0; drv_id < USBH_CLASS_DRIVER_COUNT; drv_id++) { - TU_LOG_USBH("%s close\r\n", usbh_class_drivers[drv_id].name); usbh_class_drivers[drv_id].close(dev_addr); } @@ -1449,6 +1454,7 @@ static uint8_t get_new_address(bool is_hub) { uint8_t start; uint8_t end; + if ( is_hub ) { start = CFG_TUH_DEVICE_MAX; @@ -1459,7 +1465,7 @@ static uint8_t get_new_address(bool is_hub) end = start + CFG_TUH_DEVICE_MAX; } - for ( uint8_t idx = start; idx < end; idx++) + for (uint8_t idx = start; idx < end; idx++) { if (!_usbh_devices[idx].connected) return (idx+1); } diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 494e2e50f..69e59ce65 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -142,8 +142,11 @@ static inline ehci_qhd_t* qhd_get_from_addr (uint8_t dev_addr, uint8_t ep_addr); // determine if a queue head has bus-related error static inline bool qhd_has_xact_error (ehci_qhd_t * p_qhd) { - return (p_qhd->qtd_overlay.buffer_err || p_qhd->qtd_overlay.babble_err || p_qhd->qtd_overlay.xact_err); - //p_qhd->qtd_overlay.non_hs_period_missed_uframe || p_qhd->qtd_overlay.pingstate_err TODO split transaction error + volatile ehci_qtd_t *qtd_overlay = &p_qhd->qtd_overlay; + + // Error count = 0 often occurs when device disconnected + return (qtd_overlay->err_count == 0 || qtd_overlay->buffer_err || qtd_overlay->babble_err || qtd_overlay->xact_err); + //qtd_overlay->non_hs_period_missed_uframe || qtd_overlay->pingstate_err TODO split transaction error } static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc); @@ -630,7 +633,9 @@ static void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) p_qhd->total_xferred_bytes += p_qhd->p_qtd_list_head->expected_bytes - p_qhd->p_qtd_list_head->total_bytes; -// if ( XFER_RESULT_FAILED == error_event ) TU_BREAKPOINT(); // TODO skip unplugged device +// if ( XFER_RESULT_FAILED == error_event ) { +// TU_BREAKPOINT(); // TODO skip unplugged device +// } p_qhd->p_qtd_list_head->used = 0; // free QTD qtd_remove_1st_from_qhd(p_qhd); diff --git a/src/tusb.c b/src/tusb.c index 85fe5a3cc..7327db685 100644 --- a/src/tusb.c +++ b/src/tusb.c @@ -439,6 +439,10 @@ char const* const tu_str_std_request[] = "Synch Frame" }; +char const* const tu_str_xfer_result[] = { + "OK", "Failed", "Stalled", "Timeout" +}; + #endif static void dump_str_line(uint8_t const* buf, uint16_t count) -- cgit v1.3.1 From 1c4f22a54cf60e6221995f9b64e2e765fd0a5bfe Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 11 May 2023 22:18:40 +0700 Subject: EHCI: fix xfer failed with disconnected device as stalled - change CFG_TUH_ENDPOINT_MAX to 16 (max endpoint pair per device) if not defined - change QHD_MAX for EHCI, should be user configurable and more optimized in the future --- examples/host/cdc_msc_hid/src/hid_app.c | 2 +- hw/bsp/imxrt/family.c | 5 +++- src/class/hid/hid_host.c | 2 +- src/host/hcd.h | 4 ++- src/portable/ehci/ehci.c | 48 +++++++++++++-------------------- 5 files changed, 27 insertions(+), 34 deletions(-) (limited to 'src/portable') diff --git a/examples/host/cdc_msc_hid/src/hid_app.c b/examples/host/cdc_msc_hid/src/hid_app.c index ed53c502d..87e110ab2 100644 --- a/examples/host/cdc_msc_hid/src/hid_app.c +++ b/examples/host/cdc_msc_hid/src/hid_app.c @@ -263,7 +263,7 @@ static void process_generic_report(uint8_t dev_addr, uint8_t instance, uint8_t c if (!rpt_info) { - printf("Couldn't find the report info for this report !\r\n"); + printf("Couldn't find report info !\r\n"); return; } diff --git a/hw/bsp/imxrt/family.c b/hw/bsp/imxrt/family.c index 52d3bb91b..46adabf0a 100644 --- a/hw/bsp/imxrt/family.c +++ b/hw/bsp/imxrt/family.c @@ -131,7 +131,10 @@ void board_init(void) freq = CLOCK_GetOscFreq() / (CLOCK_GetDiv(kCLOCK_UartDiv) + 1U); } - LPUART_Init(UART_PORT, &uart_config, freq); + if ( kStatus_Success != LPUART_Init(UART_PORT, &uart_config, freq) ) { + // failed to init uart, probably baudrate is not supported + // TU_BREAKPOINT(); + } //------------- USB -------------// // Note: RT105x RT106x and later have dual USB controllers. diff --git a/src/class/hid/hid_host.c b/src/class/hid/hid_host.c index 3a491937a..6abe298e5 100644 --- a/src/class/hid/hid_host.c +++ b/src/class/hid/hid_host.c @@ -72,7 +72,7 @@ tu_static hidh_interface_t _hidh_itf[CFG_TUH_HID]; TU_ATTR_ALWAYS_INLINE static inline hidh_interface_t* get_hid_itf(uint8_t daddr, uint8_t idx) { - TU_ASSERT(daddr && idx < CFG_TUH_HID, NULL); + TU_ASSERT(daddr > 0 && idx < CFG_TUH_HID, NULL); hidh_interface_t* p_hid = &_hidh_itf[idx]; return (p_hid->daddr == daddr) ? p_hid : NULL; } diff --git a/src/host/hcd.h b/src/host/hcd.h index 623c12a12..f4e76f9ef 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -39,8 +39,10 @@ // Configuration //--------------------------------------------------------------------+ +// Max number of endpoints per device +// TODO optimize memory usage #ifndef CFG_TUH_ENDPOINT_MAX - #define CFG_TUH_ENDPOINT_MAX (CFG_TUH_HUB + CFG_TUH_HID*2 + CFG_TUH_MSC*2 + CFG_TUH_CDC*3) + #define CFG_TUH_ENDPOINT_MAX 16 // #ifdef TUP_HCD_ENDPOINT_MAX // #define CFG_TUH_ENDPPOINT_MAX TUP_HCD_ENDPOINT_MAX // #else diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 69e59ce65..080ee9bbc 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -58,7 +58,8 @@ #define FRAMELIST_SIZE (1024 >> FRAMELIST_SIZE_BIT_VALUE) -#define QHD_MAX (CFG_TUH_DEVICE_MAX*CFG_TUH_ENDPOINT_MAX) +// Total queue head pool. TODO should be user configurable and more optimize memory usage in the future +#define QHD_MAX (CFG_TUH_DEVICE_MAX*CFG_TUH_ENDPOINT_MAX + CFG_TUH_HUB) #define QTD_MAX QHD_MAX typedef struct @@ -138,17 +139,6 @@ static inline ehci_qtd_t* qtd_control(uint8_t dev_addr) static inline ehci_qhd_t* qhd_next (ehci_qhd_t const * p_qhd); static inline ehci_qhd_t* qhd_find_free (void); static inline ehci_qhd_t* qhd_get_from_addr (uint8_t dev_addr, uint8_t ep_addr); - -// determine if a queue head has bus-related error -static inline bool qhd_has_xact_error (ehci_qhd_t * p_qhd) -{ - volatile ehci_qtd_t *qtd_overlay = &p_qhd->qtd_overlay; - - // Error count = 0 often occurs when device disconnected - return (qtd_overlay->err_count == 0 || qtd_overlay->buffer_err || qtd_overlay->babble_err || qtd_overlay->xact_err); - //qtd_overlay->non_hs_period_missed_uframe || qtd_overlay->pingstate_err TODO split transaction error -} - static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc); static inline ehci_qtd_t* qtd_find_free (void); @@ -392,15 +382,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const TU_ASSERT (ep_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS); //------------- Prepare Queue Head -------------// - ehci_qhd_t * p_qhd; - - if ( ep_desc->bEndpointAddress == 0 ) - { - p_qhd = qhd_control(dev_addr); - }else - { - p_qhd = qhd_find_free(); - } + ehci_qhd_t *p_qhd = (ep_desc->bEndpointAddress == 0) ? qhd_control(dev_addr) : qhd_find_free(); TU_ASSERT(p_qhd); qhd_init(p_qhd, dev_addr, ep_desc); @@ -622,18 +604,23 @@ static void period_list_xfer_complete_isr(uint8_t hostid, uint32_t interval_ms) static void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) { - if ( (p_qhd->dev_addr != 0 && p_qhd->qtd_overlay.halted) || // addr0 cannot be protocol STALL - qhd_has_xact_error(p_qhd) ) - { - // current qhd has error in transaction - xfer_result_t error_event; + volatile ehci_qtd_t *qtd_overlay = &p_qhd->qtd_overlay; + + // TD has error + if (qtd_overlay->halted) { + xfer_result_t xfer_result; - // no error bits are set, endpoint is halted due to STALL - error_event = qhd_has_xact_error(p_qhd) ? XFER_RESULT_FAILED : XFER_RESULT_STALLED; + if (qtd_overlay->err_count == 0 || qtd_overlay->buffer_err || qtd_overlay->babble_err || qtd_overlay->xact_err) { + // Error count = 0 often occurs when device disconnected, or other bus-related error + xfer_result = XFER_RESULT_FAILED; + }else { + // no error bits are set, endpoint is halted due to STALL + xfer_result = XFER_RESULT_STALLED; + } p_qhd->total_xferred_bytes += p_qhd->p_qtd_list_head->expected_bytes - p_qhd->p_qtd_list_head->total_bytes; -// if ( XFER_RESULT_FAILED == error_event ) { +// if (XFER_RESULT_FAILED == xfer_result ) { // TU_BREAKPOINT(); // TODO skip unplugged device // } @@ -655,7 +642,8 @@ static void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) } // call USBH callback - hcd_event_xfer_complete(p_qhd->dev_addr, tu_edpt_addr(p_qhd->ep_number, p_qhd->pid == EHCI_PID_IN ? 1 : 0), p_qhd->total_xferred_bytes, error_event, true); + uint8_t const ep_addr = tu_edpt_addr(p_qhd->ep_number, p_qhd->pid == EHCI_PID_IN ? 1 : 0); + hcd_event_xfer_complete(p_qhd->dev_addr, ep_addr, p_qhd->total_xferred_bytes, xfer_result, true); p_qhd->total_xferred_bytes = 0; } -- cgit v1.3.1 From 1e998ce3bd1ecdf535a8a9feb6823627f3cf7c14 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 12 May 2023 10:58:42 +0700 Subject: usbd: fix control transfer issue for chipidea hs when previous status and new setup complete in the same isr frame change usbd edpt busy/stalled/claimed value to 0/1 instead of (true/false) since they are 1-bit field. --- .idea/runConfigurations/rt1010.xml | 10 -------- .idea/runConfigurations/rt1010_nxplink.xml | 10 ++++++++ src/device/usbd.c | 39 +++++++++++++++--------------- src/portable/chipidea/ci_hs/dcd_ci_hs.c | 18 +++++++------- 4 files changed, 39 insertions(+), 38 deletions(-) delete mode 100644 .idea/runConfigurations/rt1010.xml create mode 100644 .idea/runConfigurations/rt1010_nxplink.xml (limited to 'src/portable') diff --git a/.idea/runConfigurations/rt1010.xml b/.idea/runConfigurations/rt1010.xml deleted file mode 100644 index 700cb5732..000000000 --- a/.idea/runConfigurations/rt1010.xml +++ /dev/null @@ -1,10 +0,0 @@ - - - - - - - - - \ No newline at end of file diff --git a/.idea/runConfigurations/rt1010_nxplink.xml b/.idea/runConfigurations/rt1010_nxplink.xml new file mode 100644 index 000000000..cf3bf842f --- /dev/null +++ b/.idea/runConfigurations/rt1010_nxplink.xml @@ -0,0 +1,10 @@ + + + + + + + + + \ No newline at end of file diff --git a/src/device/usbd.c b/src/device/usbd.c index cee56af60..409a5ec10 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -516,9 +516,9 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) _usbd_dev.connected = 1; // mark both in & out control as free - _usbd_dev.ep_status[0][TUSB_DIR_OUT].busy = false; + _usbd_dev.ep_status[0][TUSB_DIR_OUT].busy = 0; _usbd_dev.ep_status[0][TUSB_DIR_OUT].claimed = 0; - _usbd_dev.ep_status[0][TUSB_DIR_IN ].busy = false; + _usbd_dev.ep_status[0][TUSB_DIR_IN ].busy = 0; _usbd_dev.ep_status[0][TUSB_DIR_IN ].claimed = 0; // Process control request @@ -540,12 +540,13 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) TU_LOG(USBD_DBG, "on EP %02X with %u bytes\r\n", ep_addr, (unsigned int) event.xfer_complete.len); - _usbd_dev.ep_status[epnum][ep_dir].busy = false; + _usbd_dev.ep_status[epnum][ep_dir].busy = 0; _usbd_dev.ep_status[epnum][ep_dir].claimed = 0; if ( 0 == epnum ) { - usbd_control_xfer_cb(event.rhport, ep_addr, (xfer_result_t)event.xfer_complete.result, event.xfer_complete.len); + usbd_control_xfer_cb(event.rhport, ep_addr, (xfer_result_t) event.xfer_complete.result, event.xfer_complete + .len); } else { @@ -553,7 +554,7 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) TU_ASSERT(driver, ); TU_LOG(USBD_DBG, " %s xfer callback\r\n", driver->name); - driver->xfer_cb(event.rhport, ep_addr, (xfer_result_t)event.xfer_complete.result, event.xfer_complete.len); + driver->xfer_cb(event.rhport, ep_addr, (xfer_result_t) event.xfer_complete.result, event.xfer_complete.len); } } break; @@ -1244,7 +1245,7 @@ bool usbd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t // Set busy first since the actual transfer can be complete before dcd_edpt_xfer() // could return and USBD task can preempt and clear the busy - _usbd_dev.ep_status[epnum][dir].busy = true; + _usbd_dev.ep_status[epnum][dir].busy = 1; if ( dcd_edpt_xfer(rhport, ep_addr, buffer, total_bytes) ) { @@ -1252,7 +1253,7 @@ bool usbd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t }else { // DCD error, mark endpoint as ready to allow next transfer - _usbd_dev.ep_status[epnum][dir].busy = false; + _usbd_dev.ep_status[epnum][dir].busy = 0; _usbd_dev.ep_status[epnum][dir].claimed = 0; TU_LOG(USBD_DBG, "FAILED\r\n"); TU_BREAKPOINT(); @@ -1278,7 +1279,7 @@ bool usbd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16 // Set busy first since the actual transfer can be complete before dcd_edpt_xfer() could return // and usbd task can preempt and clear the busy - _usbd_dev.ep_status[epnum][dir].busy = true; + _usbd_dev.ep_status[epnum][dir].busy = 1; if (dcd_edpt_xfer_fifo(rhport, ep_addr, ff, total_bytes)) { @@ -1287,7 +1288,7 @@ bool usbd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16 }else { // DCD error, mark endpoint as ready to allow next transfer - _usbd_dev.ep_status[epnum][dir].busy = false; + _usbd_dev.ep_status[epnum][dir].busy = 0; _usbd_dev.ep_status[epnum][dir].claimed = 0; TU_LOG(USBD_DBG, "failed\r\n"); TU_BREAKPOINT(); @@ -1317,8 +1318,8 @@ void usbd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { TU_LOG(USBD_DBG, " Stall EP %02X\r\n", ep_addr); dcd_edpt_stall(rhport, ep_addr); - _usbd_dev.ep_status[epnum][dir].stalled = true; - _usbd_dev.ep_status[epnum][dir].busy = true; + _usbd_dev.ep_status[epnum][dir].stalled = 1; + _usbd_dev.ep_status[epnum][dir].busy = 1; } } @@ -1334,8 +1335,8 @@ void usbd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { TU_LOG(USBD_DBG, " Clear Stall EP %02X\r\n", ep_addr); dcd_edpt_clear_stall(rhport, ep_addr); - _usbd_dev.ep_status[epnum][dir].stalled = false; - _usbd_dev.ep_status[epnum][dir].busy = false; + _usbd_dev.ep_status[epnum][dir].stalled = 0; + _usbd_dev.ep_status[epnum][dir].busy = 0; } } @@ -1366,9 +1367,9 @@ void usbd_edpt_close(uint8_t rhport, uint8_t ep_addr) uint8_t const dir = tu_edpt_dir(ep_addr); dcd_edpt_close(rhport, ep_addr); - _usbd_dev.ep_status[epnum][dir].stalled = false; - _usbd_dev.ep_status[epnum][dir].busy = false; - _usbd_dev.ep_status[epnum][dir].claimed = false; + _usbd_dev.ep_status[epnum][dir].stalled = 0; + _usbd_dev.ep_status[epnum][dir].busy = 0; + _usbd_dev.ep_status[epnum][dir].claimed = 0; return; } @@ -1403,9 +1404,9 @@ bool usbd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const * desc_ep TU_ASSERT(epnum < CFG_TUD_ENDPPOINT_MAX); TU_ASSERT(tu_edpt_validate(desc_ep, (tusb_speed_t) _usbd_dev.speed)); - _usbd_dev.ep_status[epnum][dir].stalled = false; - _usbd_dev.ep_status[epnum][dir].busy = false; - _usbd_dev.ep_status[epnum][dir].claimed = false; + _usbd_dev.ep_status[epnum][dir].stalled = 0; + _usbd_dev.ep_status[epnum][dir].busy = 0; + _usbd_dev.ep_status[epnum][dir].claimed = 0; return dcd_edpt_iso_activate(rhport, desc_ep); } diff --git a/src/portable/chipidea/ci_hs/dcd_ci_hs.c b/src/portable/chipidea/ci_hs/dcd_ci_hs.c index bc6736cf2..9be79a2f1 100644 --- a/src/portable/chipidea/ci_hs/dcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/dcd_ci_hs.c @@ -616,15 +616,6 @@ void dcd_int_handler(uint8_t rhport) uint32_t const edpt_complete = dcd_reg->ENDPTCOMPLETE; dcd_reg->ENDPTCOMPLETE = edpt_complete; // acknowledge - if (dcd_reg->ENDPTSETUPSTAT) - { - //------------- Set up Received -------------// - // 23.10.10.2 Operational model for setup transfers - dcd_reg->ENDPTSETUPSTAT = dcd_reg->ENDPTSETUPSTAT; - - dcd_event_setup_received(rhport, (uint8_t*)(uintptr_t) &_dcd_data.qhd[0][0].setup_request, true); - } - // 23.10.12.3 Failed QTD also get ENDPTCOMPLETE set // nothing to do, we will submit xfer as error to usbd // if (int_status & INTR_ERROR) { } @@ -637,6 +628,15 @@ void dcd_int_handler(uint8_t rhport) if ( tu_bit_test(edpt_complete, epnum+16) ) process_edpt_complete_isr(rhport, epnum, TUSB_DIR_IN); } } + + // Set up Received + // 23.10.10.2 Operational model for setup transfers + // Must be after normal transfer complete since it is possible to have both previous control status + new setup + // in the same frame and we should handle previous status first. + if (dcd_reg->ENDPTSETUPSTAT) { + dcd_reg->ENDPTSETUPSTAT = dcd_reg->ENDPTSETUPSTAT; + dcd_event_setup_received(rhport, (uint8_t *) (uintptr_t) &_dcd_data.qhd[0][0].setup_request, true); + } } if (int_status & INTR_SOF) -- cgit v1.3.1 From a9aa0e3a1a9323df16c91d7705aad480033f962a Mon Sep 17 00:00:00 2001 From: hathach Date: Sat, 13 May 2023 13:20:09 +0700 Subject: fix error on EHCI causes xfer error in non-queued qhd which cause memory fault --- .idea/cmake.xml | 2 + .../dual/host_hid_to_device_cdc/src/tusb_config.h | 6 +-- src/portable/ehci/ehci.c | 46 ++++++++++++++++------ src/portable/ehci/ehci.h | 2 +- 4 files changed, 37 insertions(+), 19 deletions(-) (limited to 'src/portable') diff --git a/.idea/cmake.xml b/.idea/cmake.xml index bbef86164..7dacd0003 100644 --- a/.idea/cmake.xml +++ b/.idea/cmake.xml @@ -2,6 +2,7 @@ + @@ -27,6 +28,7 @@ + \ No newline at end of file diff --git a/examples/dual/host_hid_to_device_cdc/src/tusb_config.h b/examples/dual/host_hid_to_device_cdc/src/tusb_config.h index 2185cd1f1..8133ed418 100644 --- a/examples/dual/host_hid_to_device_cdc/src/tusb_config.h +++ b/examples/dual/host_hid_to_device_cdc/src/tusb_config.h @@ -84,10 +84,6 @@ #define CFG_TUH_RPI_PIO_USB 1 #endif - -// CFG_TUSB_DEBUG is defined by compiler in DEBUG build -// #define CFG_TUSB_DEBUG 0 - /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put * into those specific section. @@ -133,7 +129,7 @@ #endif #ifndef CFG_TUH_MEM_ALIGN -#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) #endif #define CFG_TUH_HUB 1 diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 080ee9bbc..8203b0f06 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -93,16 +93,30 @@ CFG_TUH_MEM_SECTION TU_ATTR_ALIGNED(4096) static ehci_data_t ehci_data; // Debug //--------------------------------------------------------------------+ #if CFG_TUSB_DEBUG >= EHCI_DBG -static inline void print_portsc(ehci_registers_t* regs) -{ +static inline void print_portsc(ehci_registers_t* regs) { TU_LOG_HEX(EHCI_DBG, regs->portsc); - TU_LOG(EHCI_DBG, " Current Connect Status: %u\r\n", regs->portsc_bm.current_connect_status); - TU_LOG(EHCI_DBG, " Connect Status Change : %u\r\n", regs->portsc_bm.connect_status_change); - TU_LOG(EHCI_DBG, " Port Enabled : %u\r\n", regs->portsc_bm.port_enabled); - TU_LOG(EHCI_DBG, " Port Enabled Change : %u\r\n", regs->portsc_bm.port_enable_change); - - TU_LOG(EHCI_DBG, " Port Reset : %u\r\n", regs->portsc_bm.port_reset); - TU_LOG(EHCI_DBG, " Port Power : %u\r\n", regs->portsc_bm.port_power); + TU_LOG(EHCI_DBG, " Connect Status : %u\r\n", regs->portsc_bm.current_connect_status); + TU_LOG(EHCI_DBG, " Connect Change : %u\r\n", regs->portsc_bm.connect_status_change); + TU_LOG(EHCI_DBG, " Enabled : %u\r\n", regs->portsc_bm.port_enabled); + TU_LOG(EHCI_DBG, " Enabled Change : %u\r\n", regs->portsc_bm.port_enable_change); + + TU_LOG(EHCI_DBG, " OverCurr Change: %u\r\n", regs->portsc_bm.over_current_change); + TU_LOG(EHCI_DBG, " Force Resume : %u\r\n", regs->portsc_bm.force_port_resume); + TU_LOG(EHCI_DBG, " Suspend : %u\r\n", regs->portsc_bm.suspend); + TU_LOG(EHCI_DBG, " Reset : %u\r\n", regs->portsc_bm.port_reset); + TU_LOG(EHCI_DBG, " Power : %u\r\n", regs->portsc_bm.port_power); +} + +static inline void print_intr(uint32_t intr) { + TU_LOG_HEX(EHCI_DBG, intr); + TU_LOG(EHCI_DBG, " USB Interrupt : %u\r\n", (intr & EHCI_INT_MASK_USB) ? 1 : 0); + TU_LOG(EHCI_DBG, " USB Error : %u\r\n", (intr & EHCI_INT_MASK_ERROR) ? 1 : 0); + TU_LOG(EHCI_DBG, " Port Change Detect : %u\r\n", (intr & EHCI_INT_MASK_PORT_CHANGE) ? 1 : 0); + TU_LOG(EHCI_DBG, " Frame List Rollover: %u\r\n", (intr & EHCI_INT_MASK_FRAMELIST_ROLLOVER) ? 1 : 0); + TU_LOG(EHCI_DBG, " Host System Error : %u\r\n", (intr & EHCI_INT_MASK_PCI_HOST_SYSTEM_ERROR) ? 1 : 0); + TU_LOG(EHCI_DBG, " Async Advance : %u\r\n", (intr & EHCI_INT_MASK_ASYNC_ADVANCE) ? 1 : 0); +// TU_LOG(EHCI_DBG, " Interrupt on Async: %u\r\n", (intr & EHCI_INT_MASK_NXP_ASYNC)); +// TU_LOG(EHCI_DBG, " Periodic Schedule : %u\r\n", (intr & EHCI_INT_MASK_NXP_PERIODIC)); } #else @@ -166,8 +180,8 @@ void hcd_port_reset(uint8_t rhport) ehci_registers_t* regs = ehci_data.regs; - // mask out all change bits since they are Write 1 to clear - uint32_t portsc = regs->portsc & ~EHCI_PORTSC_MASK_CHANGE_ALL; + // mask out Write-1-to-Clear bits + uint32_t portsc = regs->portsc & ~EHCI_PORTSC_MASK_W1C; // EHCI Table 2-16 PortSC // when software writes Port Reset bit to a one, it must also write a zero to the Port Enable bit. @@ -347,7 +361,7 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) // Power Control (PPC) field in the HCSPARAMS register. if (ehci_data.cap_regs->hcsparams_bm.port_power_control) { // mask out all change bits since they are Write 1 to clear - uint32_t portsc = (regs->portsc & ~EHCI_PORTSC_MASK_CHANGE_ALL); + uint32_t portsc = (regs->portsc & ~EHCI_PORTSC_MASK_W1C); portsc |= ECHI_PORTSC_MASK_PORT_POWER; regs->portsc = portsc; @@ -621,9 +635,14 @@ static void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) p_qhd->total_xferred_bytes += p_qhd->p_qtd_list_head->expected_bytes - p_qhd->p_qtd_list_head->total_bytes; // if (XFER_RESULT_FAILED == xfer_result ) { +// TU_LOG1(" QHD xfer err count: %d\n", qtd_overlay->err_count); // TU_BREAKPOINT(); // TODO skip unplugged device +// while(1){} // } + // No TD, probably an signal noise ? + TU_VERIFY(p_qhd->p_qtd_list_head, ); + p_qhd->p_qtd_list_head->used = 0; // free QTD qtd_remove_1st_from_qhd(p_qhd); @@ -710,7 +729,8 @@ void hcd_int_handler(uint8_t rhport) if (int_status & EHCI_INT_MASK_PORT_CHANGE) { - uint32_t const port_status = regs->portsc & EHCI_PORTSC_MASK_CHANGE_ALL; + // Including: Force port resume, over-current change, enable/disable change and connect status change. + uint32_t const port_status = regs->portsc & EHCI_PORTSC_MASK_W1C; print_portsc(regs); if (regs->portsc_bm.connect_status_change) diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index dd090cb36..a73e43707 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -306,7 +306,7 @@ enum { EHCI_PORTSC_MASK_PORT_RESET = TU_BIT(8), ECHI_PORTSC_MASK_PORT_POWER = TU_BIT(12), - EHCI_PORTSC_MASK_CHANGE_ALL = + EHCI_PORTSC_MASK_W1C = EHCI_PORTSC_MASK_CONNECT_STATUS_CHANGE | EHCI_PORTSC_MASK_PORT_ENABLE_CHANGE | EHCI_PORTSC_MASK_OVER_CURRENT_CHANGE -- cgit v1.3.1 From eb89df411540cb8cf5323991516a45590fa0b81d Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 17 May 2023 16:14:35 +0700 Subject: adding hcd_dcache_clean/hcd_dcache_invalidate --- hw/bsp/imxrt/family.cmake | 15 +++++++++++++++ src/host/hcd.h | 10 ++++++++++ src/portable/chipidea/ci_hs/hcd_ci_hs.c | 9 +++++++++ src/portable/ehci/ehci.h | 7 +++++++ 4 files changed, 41 insertions(+) (limited to 'src/portable') diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index 77ac05c87..4628abc34 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -144,6 +144,21 @@ function(family_configure_target TARGET) COMMAND ${LINKSERVER_PATH} flash ${NXPLINK_DEVICE} load $ ) + # Flash using jlink + set(JLINKEXE JLinkExe) + file(GENERATE + OUTPUT ${CMAKE_CURRENT_BINARY_DIR}/${TARGET}.jlink + CONTENT "halt +loadfile $ +r +go +exit" + ) + add_custom_target(${TARGET}-jlink + DEPENDS ${TARGET} + COMMAND ${JLINKEXE} -device ${JLINK_DEVICE} -if swd -JTAGConf -1,-1 -speed auto -CommandFile ${CMAKE_CURRENT_BINARY_DIR}/${TARGET}.jlink + ) + endfunction() diff --git a/src/host/hcd.h b/src/host/hcd.h index f4e76f9ef..38c89a1d2 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -104,6 +104,16 @@ typedef struct uint8_t speed; } hcd_devtree_info_t; +//--------------------------------------------------------------------+ +// Memory API +//--------------------------------------------------------------------+ + +// clean/flush data cache: write cache -> memory +void hcd_dcache_clean(void* addr, uint32_t data_size) TU_ATTR_WEAK; + +// invalidate data cache: mark cache as invalid, next read will read from memory +void hcd_dcache_invalidate(void* addr, uint32_t data_size) TU_ATTR_WEAK; + //--------------------------------------------------------------------+ // Controller API //--------------------------------------------------------------------+ diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index b06633f30..56ca01f85 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -41,6 +41,15 @@ #if CFG_TUSB_MCU == OPT_MCU_MIMXRT #include "ci_hs_imxrt.h" + + void hcd_dcache_clean(void* addr, uint32_t data_size) { + SCB_CleanDCache_by_Addr((uint32_t*) addr, (int32_t) data_size); + } + + void hcd_dcache_invalidate(void* addr, uint32_t data_size) { + SCB_InvalidateDCache_by_Addr(addr, (int32_t) data_size); + } + #elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) #include "ci_hs_lpc18_43.h" #else diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index a73e43707..56befd306 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -268,6 +268,7 @@ TU_VERIFY_STATIC( sizeof(ehci_sitd_t) == 32, "size is not correct" ); // EHCI Operational Register //--------------------------------------------------------------------+ enum { + // Bit 0-5 has maskable in interrupt enabled register EHCI_INT_MASK_USB = TU_BIT(0), EHCI_INT_MASK_ERROR = TU_BIT(1), EHCI_INT_MASK_PORT_CHANGE = TU_BIT(2), @@ -276,6 +277,12 @@ enum { EHCI_INT_MASK_ASYNC_ADVANCE = TU_BIT(5), EHCI_INT_MASK_NXP_SOF = TU_BIT(7), + + EHCI_INT_MASK_HC_HALTED = TU_BIT(12), + EHCI_INT_MASK_RECLAIMATION = TU_BIT(13), + EHCI_INT_MASK_PERIODIC_SCHED_STATUS = TU_BIT(14), + EHCI_INT_MASK_ASYNC_SCHED_STATUS = TU_BIT(15), + EHCI_INT_MASK_NXP_ASYNC = TU_BIT(18), EHCI_INT_MASK_NXP_PERIODIC = TU_BIT(19), -- cgit v1.3.1 From 32f9f452afc4d431d51cb16a02f99d76c88f7fb9 Mon Sep 17 00:00:00 2001 From: Martino Facchin Date: Wed, 17 May 2023 12:13:25 +0200 Subject: renesas: provide default for CFG_TUSB_RHPORT1_MODE Should fix CI failure for Renesas RX family --- src/portable/renesas/rusb2/dcd_rusb2.c | 1 + src/portable/renesas/rusb2/hcd_rusb2.c | 1 + src/portable/renesas/rusb2/rusb2_ra.h | 1 + 3 files changed, 3 insertions(+) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index f509dcc56..2653d0da6 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -40,6 +40,7 @@ #if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE) // fallback #define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE +#define CFG_TUSB_RHPORT1_MODE 0 #endif #if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 1ec25f1e2..1e26c931d 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -36,6 +36,7 @@ #if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE) // fallback #define CFG_TUSB_RHPORT0_MODE OPT_MODE_HOST +#define CFG_TUSB_RHPORT1_MODE 0 #endif #if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 874492304..a1c58abe5 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -40,6 +40,7 @@ extern IRQn_Type _usb_hs_irqn; #if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE) // fallback #define CFG_TUSB_RHPORT0_MODE ( CFG_TUD_ENABLED ? OPT_MODE_DEVICE : OPT_MODE_HOST ) +#define CFG_TUSB_RHPORT1_MODE 0 #endif TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_enable(uint8_t rhport) -- cgit v1.3.1 From a3e017bfd2923dcb1ce86d395606a24e2285e54a Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 18 May 2023 10:04:48 +0700 Subject: EHCI adding dcahe support, passing enumertaion --- src/host/hcd.h | 10 +- src/portable/chipidea/ci_hs/hcd_ci_hs.c | 4 + src/portable/ehci/ehci.c | 167 ++++++++++++++++++++------------ src/portable/ehci/ehci.h | 1 + 4 files changed, 117 insertions(+), 65 deletions(-) (limited to 'src/portable') diff --git a/src/host/hcd.h b/src/host/hcd.h index 38c89a1d2..c6fde2adc 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -108,12 +108,18 @@ typedef struct // Memory API //--------------------------------------------------------------------+ -// clean/flush data cache: write cache -> memory +// clean/flush data cache: write cache -> memory. +// Required before an DMA TX transfer to make sure data is in memory void hcd_dcache_clean(void* addr, uint32_t data_size) TU_ATTR_WEAK; // invalidate data cache: mark cache as invalid, next read will read from memory +// Required BOTH before and after an DMA RX transfer void hcd_dcache_invalidate(void* addr, uint32_t data_size) TU_ATTR_WEAK; +// clean and invalidate data cache +// Required before an DMA transfer where memory is both read/write by DMA +void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) TU_ATTR_WEAK; + //--------------------------------------------------------------------+ // Controller API //--------------------------------------------------------------------+ @@ -194,6 +200,7 @@ void hcd_event_device_attach(uint8_t rhport, bool in_isr) event.event_id = HCD_EVENT_DEVICE_ATTACH; event.connection.hub_addr = 0; event.connection.hub_port = 0; + hcd_event_handler(&event, in_isr); } @@ -224,7 +231,6 @@ void hcd_event_xfer_complete(uint8_t dev_addr, uint8_t ep_addr, uint32_t xferred event.xfer_complete.result = result; event.xfer_complete.len = xferred_bytes; - hcd_event_handler(&event, in_isr); } diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index 56ca01f85..ecb1a621c 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -50,6 +50,10 @@ SCB_InvalidateDCache_by_Addr(addr, (int32_t) data_size); } +void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { + SCB_CleanInvalidateDCache_by_Addr(addr, (int32_t) data_size); + } + #elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) #include "ci_hs_lpc18_43.h" #else diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 8203b0f06..9023e4b35 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -92,7 +92,7 @@ CFG_TUH_MEM_SECTION TU_ATTR_ALIGNED(4096) static ehci_data_t ehci_data; //--------------------------------------------------------------------+ // Debug //--------------------------------------------------------------------+ -#if CFG_TUSB_DEBUG >= EHCI_DBG +#if CFG_TUSB_DEBUG >= (EHCI_DBG + 1) static inline void print_portsc(ehci_registers_t* regs) { TU_LOG_HEX(EHCI_DBG, regs->portsc); TU_LOG(EHCI_DBG, " Connect Status : %u\r\n", regs->portsc_bm.current_connect_status); @@ -159,7 +159,7 @@ static inline ehci_qtd_t* qtd_find_free (void); static inline ehci_qtd_t* qtd_next (ehci_qtd_t const * p_qtd); static inline void qtd_insert_to_qhd (ehci_qhd_t *p_qhd, ehci_qtd_t *p_qtd_new); static inline void qtd_remove_1st_from_qhd (ehci_qhd_t *p_qhd); -static void qtd_init (ehci_qtd_t* p_qtd, void const* buffer, uint16_t total_bytes); +static void qtd_init (ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes); static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t new_type); static inline ehci_link_t* list_next (ehci_link_t *p_link_pointer); @@ -325,28 +325,27 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) // 3 --> period_head_arr[3] (8ms) // TODO EHCI_FRAMELIST_SIZE with other size than 8 - for(uint32_t i=0; iterminate = 1; regs->periodic_list_base = (uint32_t) framelist; + if(hcd_dcache_clean) { + hcd_dcache_clean(&ehci_data, sizeof(ehci_data_t)); + } + //------------- TT Control (NXP only) -------------// regs->nxp_tt_control = 0; @@ -430,6 +429,11 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const // TODO might need to disable async/period list list_insert(list_head, (ehci_link_t*) p_qhd, EHCI_QTYPE_QHD); + if(hcd_dcache_clean) { + hcd_dcache_clean(p_qhd, sizeof(ehci_qhd_t)); + hcd_dcache_clean(list_head, sizeof(ehci_link_t)); + } + return true; } @@ -441,9 +445,12 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet ehci_qtd_t* td = &ehci_data.control[dev_addr].qtd; qtd_init(td, setup_packet, 8); - td->pid = EHCI_PID_SETUP; - td->int_on_complete = 1; - td->next.terminate = 1; + td->pid = EHCI_PID_SETUP; + + if (hcd_dcache_clean && hcd_dcache_clean_invalidate) { + hcd_dcache_clean((void *) setup_packet, 8); + hcd_dcache_clean_invalidate(td, sizeof(ehci_qtd_t)); + } // sw region qhd->p_qtd_list_head = td; @@ -452,6 +459,10 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet // attach TD qhd->qtd_overlay.next.address = (uint32_t) td; + if (hcd_dcache_clean_invalidate) { + hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); + } + return true; } @@ -462,41 +473,48 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); + ehci_qhd_t* qhd; + ehci_qtd_t* qtd; + if ( epnum == 0 ) { - ehci_qhd_t* qhd = qhd_control(dev_addr); - ehci_qtd_t* qtd = qtd_control(dev_addr); + qhd = qhd_control(dev_addr); + qtd = qtd_control(dev_addr); qtd_init(qtd, buffer, buflen); // first first data toggle is always 1 (data & setup stage) qtd->data_toggle = 1; qtd->pid = dir ? EHCI_PID_IN : EHCI_PID_OUT; - qtd->int_on_complete = 1; - qtd->next.terminate = 1; - - // sw region - qhd->p_qtd_list_head = qtd; - qhd->p_qtd_list_tail = qtd; - - // attach TD - qhd->qtd_overlay.next.address = (uint32_t) qtd; }else { - ehci_qhd_t *p_qhd = qhd_get_from_addr(dev_addr, ep_addr); - ehci_qtd_t *p_qtd = qtd_find_free(); - TU_ASSERT(p_qtd); + qhd = qhd_get_from_addr(dev_addr, ep_addr); + qtd = qtd_find_free(); + TU_ASSERT(qtd); + + qtd_init(qtd, buffer, buflen); + qtd->pid = qhd->pid; + } - qtd_init(p_qtd, buffer, buflen); - p_qtd->pid = p_qhd->pid; + if (hcd_dcache_clean && hcd_dcache_clean_invalidate) { + // IN transfer: invalidate buffer, OUT transfer: clean buffer + if (dir) { + hcd_dcache_invalidate(buffer, buflen); + }else { + hcd_dcache_clean(buffer, buflen); + } + hcd_dcache_clean_invalidate(qtd, sizeof(ehci_qtd_t)); + } - // Insert TD to QH - qtd_insert_to_qhd(p_qhd, p_qtd); + // Software: assign TD to QHD + qhd->p_qtd_list_head = qtd; + qhd->p_qtd_list_tail = qtd; - p_qhd->p_qtd_list_tail->int_on_complete = 1; + // attach TD to QHD start transferring + qhd->qtd_overlay.next.address = (uint32_t) qtd; - // attach head QTD to QHD start transferring - p_qhd->qtd_overlay.next.address = (uint32_t) p_qhd->p_qtd_list_head; + if (hcd_dcache_clean_invalidate) { + hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); } return true; @@ -551,6 +569,11 @@ static void qhd_xfer_complete_isr(ehci_qhd_t * p_qhd) while(p_qhd->p_qtd_list_head != NULL && !p_qhd->p_qtd_list_head->active) { ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_qtd_list_head; + + if (hcd_dcache_invalidate) { + hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); + } + bool const is_ioc = (qtd->int_on_complete != 0); uint8_t const ep_addr = tu_edpt_addr(p_qhd->ep_number, qtd->pid == EHCI_PID_IN ? 1 : 0); @@ -573,8 +596,12 @@ static void async_list_xfer_complete_isr(ehci_qhd_t * const async_head) ehci_qhd_t *p_qhd = async_head; do { - if ( !p_qhd->qtd_overlay.halted ) // halted or error is processed in error isr - { + if (hcd_dcache_invalidate) { + hcd_dcache_invalidate(p_qhd, sizeof(ehci_qhd_t)); + } + + // halted or error is processed in error isr + if ( !p_qhd->qtd_overlay.halted ) { qhd_xfer_complete_isr(p_qhd); } p_qhd = qhd_next(p_qhd); @@ -640,8 +667,8 @@ static void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) // while(1){} // } - // No TD, probably an signal noise ? - TU_VERIFY(p_qhd->p_qtd_list_head, ); + // No TD yet, it is probably the probably an signal noise ? + TU_ASSERT(p_qhd->p_qtd_list_head, ); p_qhd->p_qtd_list_head->used = 0; // free QTD qtd_remove_1st_from_qhd(p_qhd); @@ -714,17 +741,19 @@ static void xfer_error_isr(uint8_t hostid) void hcd_int_handler(uint8_t rhport) { ehci_registers_t* regs = ehci_data.regs; + uint32_t const int_status = regs->status; - uint32_t int_status = regs->status; - int_status &= regs->inten; - - regs->status = int_status; // Acknowledge handled interrupt - - if (int_status == 0) return; + if (int_status & EHCI_INT_MASK_HC_HALTED) { + // something seriously wrong, maybe forget to flush/invalidate cache + TU_BREAKPOINT(); + TU_LOG1(" HC halted\n"); + return; + } if (int_status & EHCI_INT_MASK_FRAMELIST_ROLLOVER) { ehci_data.uframe_number += (FRAMELIST_SIZE << 3); + regs->status = EHCI_INT_MASK_FRAMELIST_ROLLOVER; // Acknowledge } if (int_status & EHCI_INT_MASK_PORT_CHANGE) @@ -739,31 +768,41 @@ void hcd_int_handler(uint8_t rhport) } regs->portsc |= port_status; // Acknowledge change bits in portsc + regs->status = EHCI_INT_MASK_PORT_CHANGE; // Acknowledge } if (int_status & EHCI_INT_MASK_ERROR) { xfer_error_isr(rhport); + regs->status = EHCI_INT_MASK_ERROR; // Acknowledge } //------------- some QTD/SITD/ITD with IOC set is completed -------------// if (int_status & EHCI_INT_MASK_NXP_ASYNC) { - async_list_xfer_complete_isr( qhd_async_head(rhport) ); + async_list_xfer_complete_isr(qhd_async_head(rhport)); + regs->status = EHCI_INT_MASK_NXP_ASYNC; // Acknowledge } if (int_status & EHCI_INT_MASK_NXP_PERIODIC) { for (uint32_t i=1; i <= FRAMELIST_SIZE; i *= 2) { - period_list_xfer_complete_isr( rhport, i ); + period_list_xfer_complete_isr(rhport, i); } + regs->status = EHCI_INT_MASK_NXP_PERIODIC; // Acknowledge + } + + if (int_status & EHCI_INT_MASK_USB) { + // TODO standard EHCI xfer complete + regs->status = EHCI_INT_MASK_USB; // Acknowledge } //------------- There is some removed async previously -------------// - if (int_status & EHCI_INT_MASK_ASYNC_ADVANCE) // need to place after EHCI_INT_MASK_NXP_ASYNC - { + // need to place after EHCI_INT_MASK_NXP_ASYNC + if (int_status & EHCI_INT_MASK_ASYNC_ADVANCE) { async_advance_isr(rhport); + regs->status = EHCI_INT_MASK_ASYNC_ADVANCE; // Acknowledge } } @@ -918,28 +957,30 @@ static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t c } } -static void qtd_init(ehci_qtd_t* p_qtd, void const* buffer, uint16_t total_bytes) +static void qtd_init(ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes) { - tu_memclr(p_qtd, sizeof(ehci_qtd_t)); + tu_memclr(qtd, sizeof(ehci_qtd_t)); + qtd->used = 1; - p_qtd->used = 1; + qtd->next.terminate = 1; // init to null + qtd->alternate.terminate = 1; // not used, always set to terminated + qtd->active = 1; + qtd->err_count = 3; // TODO 3 consecutive errors tolerance + qtd->data_toggle = 0; + qtd->int_on_complete = 1; + qtd->total_bytes = total_bytes; + qtd->expected_bytes = total_bytes; - p_qtd->next.terminate = 1; // init to null - p_qtd->alternate.terminate = 1; // not used, always set to terminated - p_qtd->active = 1; - p_qtd->err_count = 3; // TODO 3 consecutive errors tolerance - p_qtd->data_toggle = 0; - p_qtd->total_bytes = total_bytes; - p_qtd->expected_bytes = total_bytes; - - p_qtd->buffer[0] = (uint32_t) buffer; + qtd->buffer[0] = (uint32_t) buffer; for(uint8_t i=1; i<5; i++) { - p_qtd->buffer[i] |= tu_align4k( p_qtd->buffer[i-1] ) + 4096; + qtd->buffer[i] |= tu_align4k(qtd->buffer[i - 1] ) + 4096; } } //------------- List Managing Helper -------------// + +// insert at head static inline void list_insert(ehci_link_t *current, ehci_link_t *new, uint8_t new_type) { new->address = current->address; diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index 56befd306..e76a59401 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -165,6 +165,7 @@ typedef struct TU_ATTR_ALIGNED(32) uint16_t total_xferred_bytes; // number of bytes xferred until a qtd with ioc bit set uint8_t reserved2[2]; + // TODO USBH will only queue 1 TD per QHD, thus we can remove the list ehci_qtd_t * volatile p_qtd_list_head; // head of the scheduled TD list ehci_qtd_t * volatile p_qtd_list_tail; // tail of the scheduled TD list } ehci_qhd_t; -- cgit v1.3.1 From e4f4ad5bc3a24f619b9cf6c542aaa3ff8cb37ec4 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 18 May 2023 10:21:11 +0700 Subject: use weak local for dcache function to skip if() --- src/portable/ehci/ehci.c | 65 +++++++++++++++++++++++++----------------------- 1 file changed, 34 insertions(+), 31 deletions(-) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 9023e4b35..ac715aa60 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -164,6 +164,25 @@ static void qtd_init (ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes) static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t new_type); static inline ehci_link_t* list_next (ehci_link_t *p_link_pointer); +TU_ATTR_WEAK void hcd_dcache_clean(void* addr, uint32_t data_size) { + (void) addr; + (void) data_size; +} + +// invalidate data cache: mark cache as invalid, next read will read from memory +// Required BOTH before and after an DMA RX transfer +TU_ATTR_WEAK void hcd_dcache_invalidate(void* addr, uint32_t data_size) { + (void) addr; + (void) data_size; +} + +// clean and invalidate data cache +// Required before an DMA transfer where memory is both read/write by DMA +TU_ATTR_WEAK void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { + (void) addr; + (void) data_size; +} + //--------------------------------------------------------------------+ // HCD API //--------------------------------------------------------------------+ @@ -342,9 +361,7 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) regs->periodic_list_base = (uint32_t) framelist; - if(hcd_dcache_clean) { - hcd_dcache_clean(&ehci_data, sizeof(ehci_data_t)); - } + hcd_dcache_clean(&ehci_data, sizeof(ehci_data_t)); //------------- TT Control (NXP only) -------------// regs->nxp_tt_control = 0; @@ -429,10 +446,8 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const // TODO might need to disable async/period list list_insert(list_head, (ehci_link_t*) p_qhd, EHCI_QTYPE_QHD); - if(hcd_dcache_clean) { - hcd_dcache_clean(p_qhd, sizeof(ehci_qhd_t)); - hcd_dcache_clean(list_head, sizeof(ehci_link_t)); - } + hcd_dcache_clean(p_qhd, sizeof(ehci_qhd_t)); + hcd_dcache_clean(list_head, sizeof(ehci_link_t)); return true; } @@ -447,10 +462,8 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet qtd_init(td, setup_packet, 8); td->pid = EHCI_PID_SETUP; - if (hcd_dcache_clean && hcd_dcache_clean_invalidate) { - hcd_dcache_clean((void *) setup_packet, 8); - hcd_dcache_clean_invalidate(td, sizeof(ehci_qtd_t)); - } + hcd_dcache_clean((void *) setup_packet, 8); + hcd_dcache_clean_invalidate(td, sizeof(ehci_qtd_t)); // sw region qhd->p_qtd_list_head = td; @@ -459,9 +472,7 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet // attach TD qhd->qtd_overlay.next.address = (uint32_t) td; - if (hcd_dcache_clean_invalidate) { - hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); - } + hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); return true; } @@ -496,15 +507,13 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * qtd->pid = qhd->pid; } - if (hcd_dcache_clean && hcd_dcache_clean_invalidate) { - // IN transfer: invalidate buffer, OUT transfer: clean buffer - if (dir) { - hcd_dcache_invalidate(buffer, buflen); - }else { - hcd_dcache_clean(buffer, buflen); - } - hcd_dcache_clean_invalidate(qtd, sizeof(ehci_qtd_t)); + // IN transfer: invalidate buffer, OUT transfer: clean buffer + if (dir) { + hcd_dcache_invalidate(buffer, buflen); + }else { + hcd_dcache_clean(buffer, buflen); } + hcd_dcache_clean_invalidate(qtd, sizeof(ehci_qtd_t)); // Software: assign TD to QHD qhd->p_qtd_list_head = qtd; @@ -513,9 +522,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * // attach TD to QHD start transferring qhd->qtd_overlay.next.address = (uint32_t) qtd; - if (hcd_dcache_clean_invalidate) { - hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); - } + hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); return true; } @@ -570,9 +577,7 @@ static void qhd_xfer_complete_isr(ehci_qhd_t * p_qhd) { ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_qtd_list_head; - if (hcd_dcache_invalidate) { - hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); - } + hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); bool const is_ioc = (qtd->int_on_complete != 0); uint8_t const ep_addr = tu_edpt_addr(p_qhd->ep_number, qtd->pid == EHCI_PID_IN ? 1 : 0); @@ -596,9 +601,7 @@ static void async_list_xfer_complete_isr(ehci_qhd_t * const async_head) ehci_qhd_t *p_qhd = async_head; do { - if (hcd_dcache_invalidate) { - hcd_dcache_invalidate(p_qhd, sizeof(ehci_qhd_t)); - } + hcd_dcache_invalidate(p_qhd, sizeof(ehci_qhd_t)); // halted or error is processed in error isr if ( !p_qhd->qtd_overlay.halted ) { -- cgit v1.3.1 From a0aea52a117246f246529459f9203ce36d2fcd81 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 18 May 2023 12:39:53 +0700 Subject: more cache, fix an similar issue with OHCI when removing an queue head --- src/portable/ehci/ehci.c | 50 ++++++++++++++++++++++++++---------------------- src/portable/ehci/ehci.h | 2 ++ 2 files changed, 29 insertions(+), 23 deletions(-) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index ac715aa60..0b4202788 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -162,7 +162,7 @@ static inline void qtd_remove_1st_from_qhd (ehci_qhd_t *p_qhd); static void qtd_init (ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes); static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t new_type); -static inline ehci_link_t* list_next (ehci_link_t *p_link_pointer); +static inline ehci_link_t* list_next (ehci_link_t const *p_link); TU_ATTR_WEAK void hcd_dcache_clean(void* addr, uint32_t data_size) { (void) addr; @@ -237,24 +237,22 @@ tusb_speed_t hcd_port_speed_get(uint8_t rhport) return (tusb_speed_t) ehci_data.regs->portsc_bm.nxp_port_speed; // NXP specific port speed } -static void list_remove_qhd_by_addr(ehci_link_t* list_head, uint8_t dev_addr) -{ - for(ehci_link_t* prev = list_head; - !prev->terminate && (tu_align32(prev->address) != (uint32_t) list_head) && prev != NULL; - prev = list_next(prev) ) - { - // TODO check type for ISO iTD and siTD - // TODO Suppress cast-align warning - #pragma GCC diagnostic push - #pragma GCC diagnostic ignored "-Wcast-align" - ehci_qhd_t* qhd = (ehci_qhd_t*) list_next(prev); - #pragma GCC diagnostic pop - if ( qhd->dev_addr == dev_addr ) - { +static void list_remove_qhd_by_daddr(ehci_link_t* list_head, uint8_t dev_addr) { + ehci_link_t* prev = list_head; + + while (prev && !prev->terminate) { + ehci_qhd_t* qhd = (ehci_qhd_t*) (uintptr_t) list_next(prev); + + // done if loop back to head + if ( (uintptr_t) qhd == (uintptr_t) list_head) { + break; + } + + if ( qhd->dev_addr == dev_addr ) { // TODO deactivate all TD, wait for QHD to inactive before removal prev->address = qhd->next.address; - // EHCI 4.8.2 link the removed qhd to async head (which always reachable by Host Controller) + // EHCI 4.8.2 link the removed qhd's next to async head (which always reachable by Host Controller) qhd->next.address = ((uint32_t) list_head) | (EHCI_QTYPE_QHD << 1); if ( qhd->int_smask ) @@ -267,6 +265,11 @@ static void list_remove_qhd_by_addr(ehci_link_t* list_head, uint8_t dev_addr) // mark as removing, will completely re-usable when async advance isr occurs qhd->removing = 1; } + + hcd_dcache_clean(qhd, sizeof(ehci_qhd_t)); + hcd_dcache_clean(prev, sizeof(ehci_qhd_t)); + }else { + prev = list_next(prev); } } } @@ -275,15 +278,16 @@ static void list_remove_qhd_by_addr(ehci_link_t* list_head, uint8_t dev_addr) void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { // skip dev0 - if (dev_addr == 0) return; + if (dev_addr == 0) { + return; + } // Remove from async list - list_remove_qhd_by_addr( (ehci_link_t*) qhd_async_head(rhport), dev_addr ); + list_remove_qhd_by_daddr((ehci_link_t *) qhd_async_head(rhport), dev_addr); // Remove from all interval period list - for(uint8_t i = 0; i < TU_ARRAY_SIZE(ehci_data.period_head_arr); i++) - { - list_remove_qhd_by_addr( (ehci_link_t*) &ehci_data.period_head_arr[i], dev_addr); + for(uint8_t i = 0; i < TU_ARRAY_SIZE(ehci_data.period_head_arr); i++) { + list_remove_qhd_by_daddr((ehci_link_t *) &ehci_data.period_head_arr[i], dev_addr); } // Async doorbell (EHCI 4.8.2 for operational details) @@ -990,9 +994,9 @@ static inline void list_insert(ehci_link_t *current, ehci_link_t *new, uint8_t n current->address = ((uint32_t) new) | (new_type << 1); } -static inline ehci_link_t* list_next(ehci_link_t *p_link_pointer) +static inline ehci_link_t* list_next(ehci_link_t const *p_link) { - return (ehci_link_t*) tu_align32(p_link_pointer->address); + return (ehci_link_t*) tu_align32(p_link->address); } #endif diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index e76a59401..d7d37d627 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -81,6 +81,8 @@ typedef union { }; }ehci_link_t; +TU_VERIFY_STATIC( sizeof(ehci_link_t) == 4, "size is not correct" ); + /// Queue Element Transfer Descriptor /// Qtd is used to declare overlay in ehci_qhd_t -> cannot be declared with TU_ATTR_ALIGNED(32) typedef struct -- cgit v1.3.1 From 49e2aabc819f761284dd490fd4f1c5d4ad5c3695 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 18 May 2023 13:45:38 +0700 Subject: EHCI more improvement - more dcache clean/invalidate - extract init_periodic_list() - improve isr list handling --- src/host/hcd.h | 2 +- src/portable/ehci/ehci.c | 196 +++++++++++++++++++++++++---------------------- 2 files changed, 105 insertions(+), 93 deletions(-) (limited to 'src/portable') diff --git a/src/host/hcd.h b/src/host/hcd.h index c6fde2adc..5a3b0a087 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -175,7 +175,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]); // clear stall, data toggle is also reset to DATA0 -bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr); +bool hcd_edpt_clear_stall(uint8_t daddr, uint8_t ep_addr); //--------------------------------------------------------------------+ // USBH implemented API diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 0b4202788..0b45d7b93 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -294,6 +294,40 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) ehci_data.regs->command_bm.async_adv_doorbell = 1; } +static void init_periodic_list(uint8_t rhport) { + // Build the polling interval tree with 1 ms, 2 ms, 4 ms and 8 ms (framesize) only + for ( uint32_t i = 0; i < TU_ARRAY_SIZE(ehci_data.period_head_arr); i++ ) { + ehci_data.period_head_arr[i].int_smask = 1; // queue head in period list must have smask non-zero + ehci_data.period_head_arr[i].qtd_overlay.halted = 1; // dummy node, always inactive + } + + ehci_link_t * const framelist = ehci_data.period_framelist; + ehci_link_t * const period_1ms = get_period_head(rhport, 1u); + + // all links --> period_head_arr[0] (1ms) + // 0, 2, 4, 6 etc --> period_head_arr[1] (2ms) + // 1, 5 --> period_head_arr[2] (4ms) + // 3 --> period_head_arr[3] (8ms) + + // TODO EHCI_FRAMELIST_SIZE with other size than 8 + for (uint32_t i = 0; i < FRAMELIST_SIZE; i++) { + framelist[i].address = (uint32_t) period_1ms; + framelist[i].type = EHCI_QTYPE_QHD; + } + + for (uint32_t i = 0; i < FRAMELIST_SIZE; i += 2) { + list_insert(framelist + i, get_period_head(rhport, 2u), EHCI_QTYPE_QHD); + } + + for (uint32_t i = 1; i < FRAMELIST_SIZE; i += 4) { + list_insert(framelist + i, get_period_head(rhport, 4u), EHCI_QTYPE_QHD); + } + + list_insert(framelist + 3, get_period_head(rhport, 8u), EHCI_QTYPE_QHD); + + period_1ms->terminate = 1; +} + bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) { tu_memclr(&ehci_data, sizeof(ehci_data_t)); @@ -332,38 +366,8 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) regs->async_list_addr = (uint32_t) async_head; //------------- Periodic List -------------// - // Build the polling interval tree with 1 ms, 2 ms, 4 ms and 8 ms (framesize) only - for ( uint32_t i = 0; i < TU_ARRAY_SIZE(ehci_data.period_head_arr); i++ ) - { - ehci_data.period_head_arr[i].int_smask = 1; // queue head in period list must have smask non-zero - ehci_data.period_head_arr[i].qtd_overlay.halted = 1; // dummy node, always inactive - } - - ehci_link_t * const framelist = ehci_data.period_framelist; - ehci_link_t * const period_1ms = get_period_head(rhport, 1u); - - // all links --> period_head_arr[0] (1ms) - // 0, 2, 4, 6 etc --> period_head_arr[1] (2ms) - // 1, 5 --> period_head_arr[2] (4ms) - // 3 --> period_head_arr[3] (8ms) - - // TODO EHCI_FRAMELIST_SIZE with other size than 8 - for (uint32_t i = 0; i < FRAMELIST_SIZE; i++) { - framelist[i].address = (uint32_t) period_1ms; - framelist[i].type = EHCI_QTYPE_QHD; - } - - for (uint32_t i = 0; i < FRAMELIST_SIZE; i += 2) { - list_insert(framelist + i, get_period_head(rhport, 2u), EHCI_QTYPE_QHD); - } - - for (uint32_t i = 1; i < FRAMELIST_SIZE; i += 4) { - list_insert(framelist + i, get_period_head(rhport, 4u), EHCI_QTYPE_QHD); - } - list_insert(framelist + 3, get_period_head(rhport, 8u), EHCI_QTYPE_QHD); - period_1ms->terminate = 1; - - regs->periodic_list_base = (uint32_t) framelist; + init_periodic_list(rhport); + regs->periodic_list_base = (uint32_t) ehci_data.period_framelist; hcd_dcache_clean(&ehci_data, sizeof(ehci_data_t)); @@ -491,8 +495,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * ehci_qhd_t* qhd; ehci_qtd_t* qtd; - if ( epnum == 0 ) - { + if (epnum == 0) { qhd = qhd_control(dev_addr); qtd = qtd_control(dev_addr); @@ -501,8 +504,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * // first first data toggle is always 1 (data & setup stage) qtd->data_toggle = 1; qtd->pid = dir ? EHCI_PID_IN : EHCI_PID_OUT; - }else - { + } else { qhd = qhd_get_from_addr(dev_addr, ep_addr); qtd = qtd_find_free(); TU_ASSERT(qtd); @@ -531,10 +533,11 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * return true; } -bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) +bool hcd_edpt_clear_stall(uint8_t daddr, uint8_t ep_addr) { - ehci_qhd_t *p_qhd = qhd_get_from_addr(dev_addr, ep_addr); - p_qhd->qtd_overlay.halted = 0; + ehci_qhd_t *qhd = qhd_get_from_addr(daddr, ep_addr); + qhd->qtd_overlay.halted = 0; + hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); // TODO reset data toggle ? return true; } @@ -546,22 +549,22 @@ bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) // async_advance is handshake between usb stack & ehci controller. // This isr mean it is safe to modify previously removed queue head from async list. // In tinyusb, queue head is only removed when device is unplugged. -static void async_advance_isr(uint8_t rhport) +TU_ATTR_ALWAYS_INLINE static inline +void async_advance_isr(uint8_t rhport) { (void) rhport; - ehci_qhd_t* qhd_pool = ehci_data.qhd_pool; - for(uint32_t i = 0; i < QHD_MAX; i++) - { - if ( qhd_pool[i].removing ) - { + ehci_qhd_t *qhd_pool = ehci_data.qhd_pool; + for (uint32_t i = 0; i < QHD_MAX; i++) { + if (qhd_pool[i].removing) { qhd_pool[i].removing = 0; - qhd_pool[i].used = 0; + qhd_pool[i].used = 0; } } } -static void port_connect_status_change_isr(uint8_t rhport) +TU_ATTR_ALWAYS_INLINE static inline +void port_connect_status_change_isr(uint8_t rhport) { // NOTE There is an sequence plug->unplug->…..-> plug if device is powering with pre-plugged device if (ehci_data.regs->portsc_bm.current_connect_status) @@ -574,13 +577,13 @@ static void port_connect_status_change_isr(uint8_t rhport) } } -static void qhd_xfer_complete_isr(ehci_qhd_t * p_qhd) +TU_ATTR_ALWAYS_INLINE static inline +void qhd_xfer_complete_isr(ehci_qhd_t * p_qhd) { // free all TDs from the head td to the first active TD while(p_qhd->p_qtd_list_head != NULL && !p_qhd->p_qtd_list_head->active) { ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_qtd_list_head; - hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); bool const is_ioc = (qtd->int_on_complete != 0); @@ -600,7 +603,8 @@ static void qhd_xfer_complete_isr(ehci_qhd_t * p_qhd) } } -static void async_list_xfer_complete_isr(ehci_qhd_t * const async_head) +TU_ATTR_ALWAYS_INLINE static inline +void async_list_xfer_complete_isr(ehci_qhd_t * const async_head) { ehci_qhd_t *p_qhd = async_head; do @@ -611,46 +615,55 @@ static void async_list_xfer_complete_isr(ehci_qhd_t * const async_head) if ( !p_qhd->qtd_overlay.halted ) { qhd_xfer_complete_isr(p_qhd); } + p_qhd = qhd_next(p_qhd); }while(p_qhd != async_head); // async list traversal, stop if loop around } -static void period_list_xfer_complete_isr(uint8_t hostid, uint32_t interval_ms) +TU_ATTR_ALWAYS_INLINE static inline +void period_list_xfer_complete_isr(uint8_t rhport, uint32_t interval_ms) { - uint16_t max_loop = 0; - uint32_t const period_1ms_addr = (uint32_t) get_period_head(hostid, 1u); - ehci_link_t next_item = * get_period_head(hostid, interval_ms); + uint32_t const period_1ms_addr = (uint32_t) get_period_head(rhport, 1u); + ehci_link_t next_link = * get_period_head(rhport, interval_ms); - // TODO abstract max loop guard for period - while( !next_item.terminate && - !(interval_ms > 1 && period_1ms_addr == tu_align32(next_item.address)) && - max_loop < (QHD_MAX + EHCI_MAX_ITD + EHCI_MAX_SITD)*CFG_TUH_DEVICE_MAX) - { - switch ( next_item.type ) - { - case EHCI_QTYPE_QHD: - { - ehci_qhd_t *p_qhd_int = (ehci_qhd_t *) tu_align32(next_item.address); - if ( !p_qhd_int->qtd_overlay.halted ) - { - qhd_xfer_complete_isr(p_qhd_int); + while (!next_link.terminate) { + if (interval_ms > 1 && period_1ms_addr == tu_align32(next_link.address)) { + // 1ms period list is end of list for all larger interval + break; + } + + uintptr_t const entry_addr = tu_align32(next_link.address); + + switch (next_link.type) { + case EHCI_QTYPE_QHD: { + ehci_qhd_t *qhd = (ehci_qhd_t *) entry_addr; + hcd_dcache_invalidate(qhd, sizeof(ehci_qhd_t)); + + if (!qhd->qtd_overlay.halted) { + qhd_xfer_complete_isr(qhd); } } - break; + break; + + case EHCI_QTYPE_ITD: + // TODO support hs ISO + break; - case EHCI_QTYPE_ITD: // TODO support hs/fs ISO case EHCI_QTYPE_SITD: - case EHCI_QTYPE_FSTN: + // TODO support split ISO + break; - default: break; + case EHCI_QTYPE_FSTN: + default: + break; } - next_item = *list_next(&next_item); - max_loop++; + next_link = *list_next(&next_link); } } -static void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) +TU_ATTR_ALWAYS_INLINE static inline +void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) { volatile ehci_qtd_t *qtd_overlay = &p_qhd->qtd_overlay; @@ -666,22 +679,22 @@ static void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) xfer_result = XFER_RESULT_STALLED; } - p_qhd->total_xferred_bytes += p_qhd->p_qtd_list_head->expected_bytes - p_qhd->p_qtd_list_head->total_bytes; - // if (XFER_RESULT_FAILED == xfer_result ) { // TU_LOG1(" QHD xfer err count: %d\n", qtd_overlay->err_count); // TU_BREAKPOINT(); // TODO skip unplugged device // while(1){} // } - // No TD yet, it is probably the probably an signal noise ? - TU_ASSERT(p_qhd->p_qtd_list_head, ); + ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_qtd_list_head; + TU_ASSERT(qtd, ); // No TD yet, probably a race condition or cache issue !? - p_qhd->p_qtd_list_head->used = 0; // free QTD + hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); + p_qhd->total_xferred_bytes += qtd->expected_bytes - qtd->total_bytes; + + qtd->used = 0; // free QTD qtd_remove_1st_from_qhd(p_qhd); - if ( 0 == p_qhd->ep_number ) - { + if ( 0 == p_qhd->ep_number ) { // control cannot be halted --> clear all qtd list p_qhd->p_qtd_list_head = NULL; p_qhd->p_qtd_list_tail = NULL; @@ -702,13 +715,15 @@ static void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) } } -static void xfer_error_isr(uint8_t hostid) +TU_ATTR_ALWAYS_INLINE static inline +void xfer_error_isr(uint8_t hostid) { //------------- async list -------------// ehci_qhd_t * const async_head = qhd_async_head(hostid); ehci_qhd_t *p_qhd = async_head; do { + hcd_dcache_invalidate(p_qhd, sizeof(ehci_qhd_t)); qhd_xfer_error_isr( p_qhd ); p_qhd = qhd_next(p_qhd); }while(p_qhd != async_head); // async list traversal, stop if loop around @@ -728,6 +743,8 @@ static void xfer_error_isr(uint8_t hostid) case EHCI_QTYPE_QHD: { ehci_qhd_t *p_qhd_int = (ehci_qhd_t *) tu_align32(next_item.address); + hcd_dcache_invalidate(p_qhd_int, sizeof(ehci_qhd_t)); + qhd_xfer_error_isr(p_qhd_int); } break; @@ -757,20 +774,17 @@ void hcd_int_handler(uint8_t rhport) return; } - if (int_status & EHCI_INT_MASK_FRAMELIST_ROLLOVER) - { + if (int_status & EHCI_INT_MASK_FRAMELIST_ROLLOVER) { ehci_data.uframe_number += (FRAMELIST_SIZE << 3); regs->status = EHCI_INT_MASK_FRAMELIST_ROLLOVER; // Acknowledge } - if (int_status & EHCI_INT_MASK_PORT_CHANGE) - { + if (int_status & EHCI_INT_MASK_PORT_CHANGE) { // Including: Force port resume, over-current change, enable/disable change and connect status change. uint32_t const port_status = regs->portsc & EHCI_PORTSC_MASK_W1C; print_portsc(regs); - if (regs->portsc_bm.connect_status_change) - { + if (regs->portsc_bm.connect_status_change) { port_connect_status_change_isr(rhport); } @@ -778,15 +792,13 @@ void hcd_int_handler(uint8_t rhport) regs->status = EHCI_INT_MASK_PORT_CHANGE; // Acknowledge } - if (int_status & EHCI_INT_MASK_ERROR) - { + if (int_status & EHCI_INT_MASK_ERROR) { xfer_error_isr(rhport); regs->status = EHCI_INT_MASK_ERROR; // Acknowledge } //------------- some QTD/SITD/ITD with IOC set is completed -------------// - if (int_status & EHCI_INT_MASK_NXP_ASYNC) - { + if (int_status & EHCI_INT_MASK_NXP_ASYNC) { async_list_xfer_complete_isr(qhd_async_head(rhport)); regs->status = EHCI_INT_MASK_NXP_ASYNC; // Acknowledge } -- cgit v1.3.1 From 27acaa013bd8af8ac29e966d7dc145b33dd6bc73 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 18 May 2023 15:44:08 +0700 Subject: refactor ehci, since usbh only queue 1 TD per queue head --- src/portable/ehci/ehci.c | 113 ++++++++++++++--------------------------------- src/portable/ehci/ehci.h | 16 ++----- 2 files changed, 37 insertions(+), 92 deletions(-) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 0b45d7b93..a08731667 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -156,9 +156,6 @@ static inline ehci_qhd_t* qhd_get_from_addr (uint8_t dev_addr, uint8_t ep_addr); static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc); static inline ehci_qtd_t* qtd_find_free (void); -static inline ehci_qtd_t* qtd_next (ehci_qtd_t const * p_qtd); -static inline void qtd_insert_to_qhd (ehci_qhd_t *p_qhd, ehci_qtd_t *p_qtd_new); -static inline void qtd_remove_1st_from_qhd (ehci_qhd_t *p_qhd); static void qtd_init (ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes); static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t new_type); @@ -473,11 +470,8 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet hcd_dcache_clean((void *) setup_packet, 8); hcd_dcache_clean_invalidate(td, sizeof(ehci_qtd_t)); - // sw region - qhd->p_qtd_list_head = td; - qhd->p_qtd_list_tail = td; - // attach TD + qhd->p_attached_qtd = td; // software management qhd->qtd_overlay.next.address = (uint32_t) td; hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); @@ -501,7 +495,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * qtd_init(qtd, buffer, buflen); - // first first data toggle is always 1 (data & setup stage) + // first data toggle is always 1 (data & setup stage) qtd->data_toggle = 1; qtd->pid = dir ? EHCI_PID_IN : EHCI_PID_OUT; } else { @@ -521,11 +515,8 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * } hcd_dcache_clean_invalidate(qtd, sizeof(ehci_qtd_t)); - // Software: assign TD to QHD - qhd->p_qtd_list_head = qtd; - qhd->p_qtd_list_tail = qtd; - // attach TD to QHD start transferring + qhd->p_attached_qtd = qtd; // software management qhd->qtd_overlay.next.address = (uint32_t) qtd; hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); @@ -580,27 +571,25 @@ void port_connect_status_change_isr(uint8_t rhport) TU_ATTR_ALWAYS_INLINE static inline void qhd_xfer_complete_isr(ehci_qhd_t * p_qhd) { - // free all TDs from the head td to the first active TD - while(p_qhd->p_qtd_list_head != NULL && !p_qhd->p_qtd_list_head->active) - { - ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_qtd_list_head; - hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); + // examine TD attached to queue head + ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_attached_qtd; + if (qtd == NULL) return; // no TD attached + hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); - bool const is_ioc = (qtd->int_on_complete != 0); - uint8_t const ep_addr = tu_edpt_addr(p_qhd->ep_number, qtd->pid == EHCI_PID_IN ? 1 : 0); + // TD is still active, no need to process + if (qtd->active) { + return; + } - p_qhd->total_xferred_bytes += qtd->expected_bytes - qtd->total_bytes; + uint32_t const xferred_bytes = qtd->expected_bytes - qtd->total_bytes; + uint8_t const ep_addr = tu_edpt_addr(p_qhd->ep_number, qtd->pid == EHCI_PID_IN ? 1 : 0); - // TD need to be freed and removed from qhd, before invoking callback - qtd->used = 0; // free QTD - qtd_remove_1st_from_qhd(p_qhd); + // remove and free TD before invoking callback + p_qhd->p_attached_qtd = NULL; + qtd->used = 0; // free QTD - if (is_ioc) - { - hcd_event_xfer_complete(p_qhd->dev_addr, ep_addr, p_qhd->total_xferred_bytes, XFER_RESULT_SUCCESS, true); - p_qhd->total_xferred_bytes = 0; - } - } + // IOC is always set + hcd_event_xfer_complete(p_qhd->dev_addr, ep_addr, xferred_bytes, XFER_RESULT_SUCCESS, true); } TU_ATTR_ALWAYS_INLINE static inline @@ -685,20 +674,17 @@ void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) // while(1){} // } - ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_qtd_list_head; + ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_attached_qtd; TU_ASSERT(qtd, ); // No TD yet, probably a race condition or cache issue !? hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); - p_qhd->total_xferred_bytes += qtd->expected_bytes - qtd->total_bytes; + uint32_t const xferred_bytes = qtd->expected_bytes - qtd->total_bytes; + p_qhd->p_attached_qtd = NULL; qtd->used = 0; // free QTD - qtd_remove_1st_from_qhd(p_qhd); if ( 0 == p_qhd->ep_number ) { - // control cannot be halted --> clear all qtd list - p_qhd->p_qtd_list_head = NULL; - p_qhd->p_qtd_list_tail = NULL; - + // control cannot be halted p_qhd->qtd_overlay.next.terminate = 1; p_qhd->qtd_overlay.alternate.terminate = 1; p_qhd->qtd_overlay.halted = 0; @@ -707,19 +693,17 @@ void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) p_setup->used = 0; } - // call USBH callback + // notify usbh uint8_t const ep_addr = tu_edpt_addr(p_qhd->ep_number, p_qhd->pid == EHCI_PID_IN ? 1 : 0); - hcd_event_xfer_complete(p_qhd->dev_addr, ep_addr, p_qhd->total_xferred_bytes, xfer_result, true); - - p_qhd->total_xferred_bytes = 0; + hcd_event_xfer_complete(p_qhd->dev_addr, ep_addr, xferred_bytes, xfer_result, true); } } TU_ATTR_ALWAYS_INLINE static inline -void xfer_error_isr(uint8_t hostid) +void xfer_error_isr(uint8_t rhport) { //------------- async list -------------// - ehci_qhd_t * const async_head = qhd_async_head(hostid); + ehci_qhd_t * const async_head = qhd_async_head(rhport); ehci_qhd_t *p_qhd = async_head; do { @@ -729,10 +713,10 @@ void xfer_error_isr(uint8_t hostid) }while(p_qhd != async_head); // async list traversal, stop if loop around //------------- TODO refractor period list -------------// - uint32_t const period_1ms_addr = (uint32_t) get_period_head(hostid, 1u); + uint32_t const period_1ms_addr = (uint32_t) get_period_head(rhport, 1u); for (uint32_t interval_ms=1; interval_ms <= FRAMELIST_SIZE; interval_ms *= 2) { - ehci_link_t next_item = * get_period_head(hostid, interval_ms); + ehci_link_t next_item = * get_period_head(rhport, interval_ms); // TODO abstract max loop guard for period while( !next_item.terminate && @@ -873,34 +857,6 @@ static inline ehci_qtd_t* qtd_find_free(void) return NULL; } -static inline ehci_qtd_t* qtd_next(ehci_qtd_t const * p_qtd ) -{ - return (ehci_qtd_t*) tu_align32(p_qtd->next.address); -} - -static inline void qtd_remove_1st_from_qhd(ehci_qhd_t *p_qhd) -{ - if (p_qhd->p_qtd_list_head == p_qhd->p_qtd_list_tail) // last TD --> make it NULL - { - p_qhd->p_qtd_list_head = p_qhd->p_qtd_list_tail = NULL; - }else - { - p_qhd->p_qtd_list_head = qtd_next( p_qhd->p_qtd_list_head ); - } -} - -static inline void qtd_insert_to_qhd(ehci_qhd_t *p_qhd, ehci_qtd_t *p_qtd_new) -{ - if (p_qhd->p_qtd_list_head == NULL) // empty list - { - p_qhd->p_qtd_list_head = p_qhd->p_qtd_list_tail = p_qtd_new; - }else - { - p_qhd->p_qtd_list_tail->next.address = (uint32_t) p_qtd_new; - p_qhd->p_qtd_list_tail = p_qtd_new; - } -} - static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc) { // address 0 is used as async head, which always on the list --> cannot be cleared (ehci halted otherwise) @@ -955,15 +911,14 @@ static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t c p_qhd->int_smask = p_qhd->fl_int_cmask = 0; } - p_qhd->fl_hub_addr = devtree_info.hub_addr; - p_qhd->fl_hub_port = devtree_info.hub_port; - p_qhd->mult = 1; // TODO not use high bandwidth/park mode yet + p_qhd->fl_hub_addr = devtree_info.hub_addr; + p_qhd->fl_hub_port = devtree_info.hub_port; + p_qhd->mult = 1; // TODO not use high bandwidth/park mode yet //------------- HCD Management Data -------------// - p_qhd->used = 1; - p_qhd->removing = 0; - p_qhd->p_qtd_list_head = NULL; - p_qhd->p_qtd_list_tail = NULL; + p_qhd->used = 1; + p_qhd->removing = 0; + p_qhd->p_attached_qtd = NULL; p_qhd->pid = tu_edpt_dir(ep_desc->bEndpointAddress) ? EHCI_PID_IN : EHCI_PID_OUT; // PID for TD under this endpoint //------------- active, but no TD list -------------// diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index d7d37d627..b525131c6 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -164,12 +164,10 @@ typedef struct TU_ATTR_ALIGNED(32) uint8_t pid; uint8_t interval_ms; // polling interval in frames (or millisecond) - uint16_t total_xferred_bytes; // number of bytes xferred until a qtd with ioc bit set - uint8_t reserved2[2]; + uint8_t TU_RESERVED[8]; - // TODO USBH will only queue 1 TD per QHD, thus we can remove the list - ehci_qtd_t * volatile p_qtd_list_head; // head of the scheduled TD list - ehci_qtd_t * volatile p_qtd_list_tail; // tail of the scheduled TD list + // usbh will only queue 1 TD per QHD + ehci_qtd_t * volatile p_attached_qtd; } ehci_qhd_t; TU_VERIFY_STATIC( sizeof(ehci_qhd_t) == 64, "size is not correct" ); @@ -248,14 +246,6 @@ typedef struct TU_ATTR_ALIGNED(32) /// Word 4-5: Buffer Pointer List uint32_t buffer[2]; // buffer[1] TP: Transaction Position - T-Count: Transaction Count -// union{ -// uint32_t BufferPointer1; -// struct { -// volatile uint32_t TCount : 3; -// volatile uint32_t TPosition : 2; -// }; -// }; - /*---------- Word 6 ----------*/ ehci_link_t back; -- cgit v1.3.1 From ec4bd39a9209f37b02edac2f6a1ea2ef27f6b785 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 18 May 2023 16:41:06 +0700 Subject: refactor ehci: add attached_buffer for dcache invalidate for IN transfer --- src/portable/ehci/ehci.c | 116 +++++++++++++++++++++++++++-------------------- src/portable/ehci/ehci.h | 8 ++-- 2 files changed, 72 insertions(+), 52 deletions(-) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index a08731667..cc825d549 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -154,6 +154,7 @@ static inline ehci_qhd_t* qhd_next (ehci_qhd_t const * p_qhd); static inline ehci_qhd_t* qhd_find_free (void); static inline ehci_qhd_t* qhd_get_from_addr (uint8_t dev_addr, uint8_t ep_addr); static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc); +static void qhd_attach_qtd(ehci_qhd_t *qhd, ehci_qtd_t *qtd); static inline ehci_qtd_t* qtd_find_free (void); static void qtd_init (ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes); @@ -468,13 +469,9 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet td->pid = EHCI_PID_SETUP; hcd_dcache_clean((void *) setup_packet, 8); - hcd_dcache_clean_invalidate(td, sizeof(ehci_qtd_t)); - // attach TD - qhd->p_attached_qtd = td; // software management - qhd->qtd_overlay.next.address = (uint32_t) td; - - hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); + // attach TD to QHD -> start transferring + qhd_attach_qtd(qhd, td); return true; } @@ -513,13 +510,9 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * }else { hcd_dcache_clean(buffer, buflen); } - hcd_dcache_clean_invalidate(qtd, sizeof(ehci_qtd_t)); - // attach TD to QHD start transferring - qhd->p_attached_qtd = qtd; // software management - qhd->qtd_overlay.next.address = (uint32_t) qtd; - - hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); + // attach TD to QHD -> start transferring + qhd_attach_qtd(qhd, qtd); return true; } @@ -569,10 +562,9 @@ void port_connect_status_change_isr(uint8_t rhport) } TU_ATTR_ALWAYS_INLINE static inline -void qhd_xfer_complete_isr(ehci_qhd_t * p_qhd) -{ +void qhd_xfer_complete_isr(ehci_qhd_t * qhd) { // examine TD attached to queue head - ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_attached_qtd; + ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) qhd->attached_qtd; if (qtd == NULL) return; // no TD attached hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); @@ -581,15 +573,22 @@ void qhd_xfer_complete_isr(ehci_qhd_t * p_qhd) return; } + uint8_t dir = (qtd->pid == EHCI_PID_IN) ? 1 : 0; uint32_t const xferred_bytes = qtd->expected_bytes - qtd->total_bytes; - uint8_t const ep_addr = tu_edpt_addr(p_qhd->ep_number, qtd->pid == EHCI_PID_IN ? 1 : 0); + + // invalidate dcache if IN transfer + if (dir == 1 && qhd->attached_buffer != 0) { + hcd_dcache_invalidate((void*) qhd->attached_buffer, xferred_bytes); + } // remove and free TD before invoking callback - p_qhd->p_attached_qtd = NULL; + qhd->attached_qtd = NULL; + qhd->attached_buffer = 0; qtd->used = 0; // free QTD - // IOC is always set - hcd_event_xfer_complete(p_qhd->dev_addr, ep_addr, xferred_bytes, XFER_RESULT_SUCCESS, true); + // notify usbh + uint8_t const ep_addr = tu_edpt_addr(qhd->ep_number, dir); + hcd_event_xfer_complete(qhd->dev_addr, ep_addr, xferred_bytes, XFER_RESULT_SUCCESS, true); } TU_ATTR_ALWAYS_INLINE static inline @@ -651,10 +650,11 @@ void period_list_xfer_complete_isr(uint8_t rhport, uint32_t interval_ms) } } +// TODO merge with qhd_xfer_complete_isr() TU_ATTR_ALWAYS_INLINE static inline -void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) +void qhd_xfer_error_isr(ehci_qhd_t * qhd) { - volatile ehci_qtd_t *qtd_overlay = &p_qhd->qtd_overlay; + volatile ehci_qtd_t *qtd_overlay = &qhd->qtd_overlay; // TD has error if (qtd_overlay->halted) { @@ -674,28 +674,37 @@ void qhd_xfer_error_isr(ehci_qhd_t * p_qhd) // while(1){} // } - ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) p_qhd->p_attached_qtd; + ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) qhd->attached_qtd; TU_ASSERT(qtd, ); // No TD yet, probably a race condition or cache issue !? hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); + + uint8_t dir = (qtd->pid == EHCI_PID_IN) ? 1 : 0; uint32_t const xferred_bytes = qtd->expected_bytes - qtd->total_bytes; - p_qhd->p_attached_qtd = NULL; + // invalidate dcache if IN transfer + if (dir == 1 && qhd->attached_buffer != 0) { + hcd_dcache_invalidate((void*) qhd->attached_buffer, xferred_bytes); + } + + // remove and free TD before invoking callback + qhd->attached_qtd = NULL; + qhd->attached_buffer = 0; qtd->used = 0; // free QTD - if ( 0 == p_qhd->ep_number ) { + if (0 == qhd->ep_number ) { // control cannot be halted - p_qhd->qtd_overlay.next.terminate = 1; - p_qhd->qtd_overlay.alternate.terminate = 1; - p_qhd->qtd_overlay.halted = 0; + qhd->qtd_overlay.next.terminate = 1; + qhd->qtd_overlay.alternate.terminate = 1; + qhd->qtd_overlay.halted = 0; - ehci_qtd_t *p_setup = qtd_control(p_qhd->dev_addr); + ehci_qtd_t *p_setup = qtd_control(qhd->dev_addr); p_setup->used = 0; } // notify usbh - uint8_t const ep_addr = tu_edpt_addr(p_qhd->ep_number, p_qhd->pid == EHCI_PID_IN ? 1 : 0); - hcd_event_xfer_complete(p_qhd->dev_addr, ep_addr, xferred_bytes, xfer_result, true); + uint8_t const ep_addr = tu_edpt_addr(qhd->ep_number, dir); + hcd_event_xfer_complete(qhd->dev_addr, ep_addr, xferred_bytes, xfer_result, true); } } @@ -846,22 +855,10 @@ static inline ehci_qhd_t* qhd_get_from_addr(uint8_t dev_addr, uint8_t ep_addr) return NULL; } -//------------- TD helper -------------// -static inline ehci_qtd_t* qtd_find_free(void) -{ - for (uint32_t i=0; i cannot be cleared (ehci halted otherwise) - if (dev_addr != 0) - { + if (dev_addr != 0) { tu_memclr(p_qhd, sizeof(ehci_qhd_t)); } @@ -911,26 +908,47 @@ static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t c p_qhd->int_smask = p_qhd->fl_int_cmask = 0; } - p_qhd->fl_hub_addr = devtree_info.hub_addr; - p_qhd->fl_hub_port = devtree_info.hub_port; - p_qhd->mult = 1; // TODO not use high bandwidth/park mode yet + p_qhd->fl_hub_addr = devtree_info.hub_addr; + p_qhd->fl_hub_port = devtree_info.hub_port; + p_qhd->mult = 1; // TODO not use high bandwidth/park mode yet //------------- HCD Management Data -------------// - p_qhd->used = 1; - p_qhd->removing = 0; - p_qhd->p_attached_qtd = NULL; + p_qhd->used = 1; + p_qhd->removing = 0; + p_qhd->attached_qtd = NULL; p_qhd->pid = tu_edpt_dir(ep_desc->bEndpointAddress) ? EHCI_PID_IN : EHCI_PID_OUT; // PID for TD under this endpoint //------------- active, but no TD list -------------// p_qhd->qtd_overlay.halted = 0; p_qhd->qtd_overlay.next.terminate = 1; p_qhd->qtd_overlay.alternate.terminate = 1; + if (TUSB_XFER_BULK == xfer_type && p_qhd->ep_speed == TUSB_SPEED_HIGH && p_qhd->pid == EHCI_PID_OUT) { p_qhd->qtd_overlay.ping_err = 1; // do PING for Highspeed Bulk OUT, EHCI section 4.11 } } +static void qhd_attach_qtd(ehci_qhd_t *qhd, ehci_qtd_t *qtd) { + qhd->attached_qtd = qtd; + qhd->attached_buffer = qtd->buffer[0]; + + // clean and invalidate cache before physically write + hcd_dcache_clean_invalidate(qtd, sizeof(ehci_qtd_t)); + + qhd->qtd_overlay.next.address = (uint32_t) qtd; + hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); +} + + +//------------- TD helper -------------// +static inline ehci_qtd_t *qtd_find_free(void) { + for (uint32_t i = 0; i < QTD_MAX; i++) { + if (!ehci_data.qtd_pool[i].used) return &ehci_data.qtd_pool[i]; + } + return NULL; +} + static void qtd_init(ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes) { tu_memclr(qtd, sizeof(ehci_qtd_t)); diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index b525131c6..8338fb419 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -164,10 +164,12 @@ typedef struct TU_ATTR_ALIGNED(32) uint8_t pid; uint8_t interval_ms; // polling interval in frames (or millisecond) - uint8_t TU_RESERVED[8]; + uint8_t TU_RESERVED[4]; - // usbh will only queue 1 TD per QHD - ehci_qtd_t * volatile p_attached_qtd; + // Attached TD management, note usbh will only queue 1 TD per QHD. + // buffer for dcache invalidate since td's buffer is modified by HC and finding initial buffer address is not trivial + uint32_t attached_buffer; + ehci_qtd_t * volatile attached_qtd; } ehci_qhd_t; TU_VERIFY_STATIC( sizeof(ehci_qhd_t) == 64, "size is not correct" ); -- cgit v1.3.1 From f26a93908ef9dcde6818c9b271727ed6c77e87d8 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 19 May 2023 10:56:52 +0700 Subject: only clean/invalidate dcache on imxrt if memory is not in DTCM --- src/portable/chipidea/ci_hs/hcd_ci_hs.c | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-) (limited to 'src/portable') diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index ecb1a621c..ab6a42e11 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -42,17 +42,28 @@ #if CFG_TUSB_MCU == OPT_MCU_MIMXRT #include "ci_hs_imxrt.h" + // check if memory is cacheable i.e not in DTCM + TU_ATTR_ALWAYS_INLINE static inline bool is_cache_mem(uint32_t addr) { + return !(0x20000000 <= addr && addr < 0x20100000); + } + void hcd_dcache_clean(void* addr, uint32_t data_size) { - SCB_CleanDCache_by_Addr((uint32_t*) addr, (int32_t) data_size); + if (is_cache_mem((uint32_t) addr)) { + SCB_CleanDCache_by_Addr((uint32_t *) addr, (int32_t) data_size); + } } void hcd_dcache_invalidate(void* addr, uint32_t data_size) { - SCB_InvalidateDCache_by_Addr(addr, (int32_t) data_size); + if (is_cache_mem((uint32_t) addr)) { + SCB_InvalidateDCache_by_Addr(addr, (int32_t) data_size); + } } void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { + if (is_cache_mem((uint32_t) addr)) { SCB_CleanInvalidateDCache_by_Addr(addr, (int32_t) data_size); } +} #elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) #include "ci_hs_lpc18_43.h" -- cgit v1.3.1 From 5dae5e12928ba789cd7e248edd9fa91376902925 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 19 May 2023 13:32:49 +0700 Subject: ehci fix dcache clean when control endpoint failed --- hw/bsp/imxrt/family.cmake | 6 +++++- src/host/usbh.c | 3 ++- src/portable/ehci/ehci.c | 10 ++++------ src/tusb.c | 2 +- 4 files changed, 12 insertions(+), 9 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index 4628abc34..a475b4721 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -57,12 +57,16 @@ if (NOT TARGET ${BOARD_TARGET}) ) update_board(${BOARD_TARGET}) + if (NOT DEFINED LD_FILE_${TOOLCHAIN}) + set(LD_FILE_gcc ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_VARIANT}xxxxx_flexspi_nor.ld) + endif () + if (TOOLCHAIN STREQUAL "gcc") target_sources(${BOARD_TARGET} PUBLIC ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_VARIANT}.S ) target_link_options(${BOARD_TARGET} PUBLIC - "LINKER:--script=${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_VARIANT}xxxxx_flexspi_nor.ld" + "LINKER:--script=${LD_FILE_gcc}" "LINKER:-Map=$>,$,$>${CMAKE_EXECUTABLE_SUFFIX}.map" # nanolib --specs=nosys.specs diff --git a/src/host/usbh.c b/src/host/usbh.c index c56ff9459..7b265c742 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -440,7 +440,7 @@ void tuh_task_ext(uint32_t timeout_ms, bool in_isr) uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const ep_dir = tu_edpt_dir(ep_addr); - TU_LOG_USBH("on EP %02X with %u bytes %s\r\n", ep_addr, (unsigned int) event.xfer_complete.len, + TU_LOG_USBH("on EP %02X with %u bytes: %s\r\n", ep_addr, (unsigned int) event.xfer_complete.len, tu_str_xfer_result[event.xfer_complete.result]); if (event.dev_addr == 0) @@ -1255,6 +1255,7 @@ static void process_enumeration(tuh_xfer_t* xfer) { failed_count++; osal_task_delay(ATTEMPT_DELAY_MS); // delay a bit + TU_LOG1("Enumeration attempt %u\r\n", failed_count); TU_ASSERT(tuh_control_xfer(xfer), ); }else { diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index cc825d549..10e2db7b5 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -577,7 +577,7 @@ void qhd_xfer_complete_isr(ehci_qhd_t * qhd) { uint32_t const xferred_bytes = qtd->expected_bytes - qtd->total_bytes; // invalidate dcache if IN transfer - if (dir == 1 && qhd->attached_buffer != 0) { + if (dir == 1 && qhd->attached_buffer != 0 && xferred_bytes > 0) { hcd_dcache_invalidate((void*) qhd->attached_buffer, xferred_bytes); } @@ -660,7 +660,7 @@ void qhd_xfer_error_isr(ehci_qhd_t * qhd) if (qtd_overlay->halted) { xfer_result_t xfer_result; - if (qtd_overlay->err_count == 0 || qtd_overlay->buffer_err || qtd_overlay->babble_err || qtd_overlay->xact_err) { + if (qtd_overlay->xact_err || qtd_overlay->err_count == 0 || qtd_overlay->buffer_err || qtd_overlay->babble_err) { // Error count = 0 often occurs when device disconnected, or other bus-related error xfer_result = XFER_RESULT_FAILED; }else { @@ -671,7 +671,6 @@ void qhd_xfer_error_isr(ehci_qhd_t * qhd) // if (XFER_RESULT_FAILED == xfer_result ) { // TU_LOG1(" QHD xfer err count: %d\n", qtd_overlay->err_count); // TU_BREAKPOINT(); // TODO skip unplugged device -// while(1){} // } ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) qhd->attached_qtd; @@ -683,7 +682,7 @@ void qhd_xfer_error_isr(ehci_qhd_t * qhd) uint32_t const xferred_bytes = qtd->expected_bytes - qtd->total_bytes; // invalidate dcache if IN transfer - if (dir == 1 && qhd->attached_buffer != 0) { + if (dir == 1 && qhd->attached_buffer != 0 && xferred_bytes > 0) { hcd_dcache_invalidate((void*) qhd->attached_buffer, xferred_bytes); } @@ -698,8 +697,7 @@ void qhd_xfer_error_isr(ehci_qhd_t * qhd) qhd->qtd_overlay.alternate.terminate = 1; qhd->qtd_overlay.halted = 0; - ehci_qtd_t *p_setup = qtd_control(qhd->dev_addr); - p_setup->used = 0; + hcd_dcache_clean(qhd, sizeof(ehci_qhd_t)); } // notify usbh diff --git a/src/tusb.c b/src/tusb.c index 7327db685..465b608b0 100644 --- a/src/tusb.c +++ b/src/tusb.c @@ -440,7 +440,7 @@ char const* const tu_str_std_request[] = }; char const* const tu_str_xfer_result[] = { - "OK", "Failed", "Stalled", "Timeout" + "OK", "FAILED", "STALLED", "TIMEOUT" }; #endif -- cgit v1.3.1 From 7211dd18b46affdf027522e34ff3aa3b5d8d5df5 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 19 May 2023 13:42:26 +0700 Subject: more dcache fix --- src/portable/ehci/ehci.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 10e2db7b5..852e7f4fe 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -273,19 +273,19 @@ static void list_remove_qhd_by_daddr(ehci_link_t* list_head, uint8_t dev_addr) { } // Close all opened endpoint belong to this device -void hcd_device_close(uint8_t rhport, uint8_t dev_addr) +void hcd_device_close(uint8_t rhport, uint8_t daddr) { // skip dev0 - if (dev_addr == 0) { + if (daddr == 0) { return; } // Remove from async list - list_remove_qhd_by_daddr((ehci_link_t *) qhd_async_head(rhport), dev_addr); + list_remove_qhd_by_daddr((ehci_link_t *) qhd_async_head(rhport), daddr); // Remove from all interval period list for(uint8_t i = 0; i < TU_ARRAY_SIZE(ehci_data.period_head_arr); i++) { - list_remove_qhd_by_daddr((ehci_link_t *) &ehci_data.period_head_arr[i], dev_addr); + list_remove_qhd_by_daddr((ehci_link_t *) &ehci_data.period_head_arr[i], daddr); } // Async doorbell (EHCI 4.8.2 for operational details) @@ -453,7 +453,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const list_insert(list_head, (ehci_link_t*) p_qhd, EHCI_QTYPE_QHD); hcd_dcache_clean(p_qhd, sizeof(ehci_qhd_t)); - hcd_dcache_clean(list_head, sizeof(ehci_link_t)); + hcd_dcache_clean(list_head, sizeof(ehci_qhd_t)); return true; } -- cgit v1.3.1 From 1ef820ecfe569e181b8f20cb936f632e51d8257e Mon Sep 17 00:00:00 2001 From: Ha Thach Date: Tue, 23 May 2023 21:45:00 +0700 Subject: Enhance chipidea (#2075) * update chipidea dcd, remove manual ep_count and use DCCPARAMS to get number of endpoint instead * add dcd dcache for chipidea * add cmake for lpc18 * add makefile build for mcx * use fork of mcu sdk * fix ci build with nrf * flash rp2040 with openocd --- .github/workflows/build_arm.yml | 3 +- .github/workflows/cmake_arm.yml | 1 + .idea/cmake.xml | 7 +- .idea/runConfigurations/rt1010_jlink.xml | 10 + .idea/runConfigurations/rt1010_nxplink.xml | 10 - .idea/runConfigurations/rt1060_nxplink.xml | 10 - .pre-commit-config.yaml | 16 +- examples/device/CMakeLists.txt | 2 +- hw/bsp/board_mcu.h | 2 +- hw/bsp/family_support.cmake | 7 + hw/bsp/imxrt/family.cmake | 11 +- hw/bsp/lpc18/boards/lpcxpresso18s37/board.cmake | 11 + hw/bsp/lpc18/boards/mcb1800/board.cmake | 11 + hw/bsp/lpc18/family.cmake | 155 +++++++++++ hw/bsp/lpc55/family.cmake | 6 +- hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h | 166 ++++++++++++ hw/bsp/mcx/boards/mcxn947brk/board.cmake | 18 ++ hw/bsp/mcx/boards/mcxn947brk/board.h | 66 +++++ hw/bsp/mcx/boards/mcxn947brk/board.mk | 11 + hw/bsp/mcx/boards/mcxn947brk/clock_config.c | 338 ++++++++++++++++++++++++ hw/bsp/mcx/boards/mcxn947brk/clock_config.h | 177 +++++++++++++ hw/bsp/mcx/boards/mcxn947brk/pin_mux.c | 141 ++++++++++ hw/bsp/mcx/boards/mcxn947brk/pin_mux.h | 51 ++++ hw/bsp/mcx/family.c | 262 ++++++++++++++++++ hw/bsp/mcx/family.cmake | 179 +++++++++++++ hw/bsp/mcx/family.mk | 48 ++++ hw/bsp/nrf/family.cmake | 11 +- src/common/tusb_mcu.h | 26 +- src/device/dcd.h | 16 ++ src/portable/chipidea/ci_hs/ci_hs_imxrt.h | 32 ++- src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h | 6 +- src/portable/chipidea/ci_hs/ci_hs_mcx.h | 52 ++++ src/portable/chipidea/ci_hs/ci_hs_type.h | 14 +- src/portable/chipidea/ci_hs/dcd_ci_hs.c | 96 +++++-- src/portable/chipidea/ci_hs/hcd_ci_hs.c | 21 +- src/portable/ehci/ehci.c | 13 +- src/tusb_option.h | 6 +- tools/cmake/cpu/cortex-m3.cmake | 10 + tools/cmake/cpu/cortex-m33.cmake | 5 +- tools/cmake/toolchain/arm_gcc.cmake | 2 + tools/get_deps.py | 2 +- tools/make/cpu/cortex-m33.mk | 4 +- 42 files changed, 1914 insertions(+), 121 deletions(-) create mode 100644 .idea/runConfigurations/rt1010_jlink.xml delete mode 100644 .idea/runConfigurations/rt1010_nxplink.xml delete mode 100644 .idea/runConfigurations/rt1060_nxplink.xml create mode 100644 hw/bsp/lpc18/boards/lpcxpresso18s37/board.cmake create mode 100644 hw/bsp/lpc18/boards/mcb1800/board.cmake create mode 100644 hw/bsp/lpc18/family.cmake create mode 100644 hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h create mode 100644 hw/bsp/mcx/boards/mcxn947brk/board.cmake create mode 100644 hw/bsp/mcx/boards/mcxn947brk/board.h create mode 100644 hw/bsp/mcx/boards/mcxn947brk/board.mk create mode 100644 hw/bsp/mcx/boards/mcxn947brk/clock_config.c create mode 100644 hw/bsp/mcx/boards/mcxn947brk/clock_config.h create mode 100644 hw/bsp/mcx/boards/mcxn947brk/pin_mux.c create mode 100644 hw/bsp/mcx/boards/mcxn947brk/pin_mux.h create mode 100644 hw/bsp/mcx/family.c create mode 100644 hw/bsp/mcx/family.cmake create mode 100644 hw/bsp/mcx/family.mk create mode 100644 src/portable/chipidea/ci_hs/ci_hs_mcx.h create mode 100644 tools/cmake/cpu/cortex-m3.cmake (limited to 'src/portable') diff --git a/.github/workflows/build_arm.yml b/.github/workflows/build_arm.yml index f0b01b43d..917c83d74 100644 --- a/.github/workflows/build_arm.yml +++ b/.github/workflows/build_arm.yml @@ -142,8 +142,7 @@ jobs: - name: Create flash.sh run: | - #echo > flash.sh 'cmdout=$(openocd -f "interface/picoprobe.cfg" -f "target/rp2040.cfg" -c "program $1 reset exit")' - echo > flash.sh 'pyocd flash -t rp2040 $1' + echo > flash.sh 'cmdout=$(openocd -f "interface/cmsis-dap.cfg" -f "target/rp2040.cfg" -c "adapter speed 5000" -c "program $1 reset exit")' echo >> flash.sh 'if (( $? )) ; then echo $cmdout ; fi' chmod +x flash.sh diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index 844a03443..12173fb63 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -32,6 +32,7 @@ jobs: matrix: family: # Alphabetical order + - 'mcx' - 'imxrt' steps: - name: Setup Python diff --git a/.idea/cmake.xml b/.idea/cmake.xml index 7dacd0003..a80ebed3c 100644 --- a/.idea/cmake.xml +++ b/.idea/cmake.xml @@ -2,8 +2,9 @@ - - + + + @@ -29,6 +30,8 @@ + + \ No newline at end of file diff --git a/.idea/runConfigurations/rt1010_jlink.xml b/.idea/runConfigurations/rt1010_jlink.xml new file mode 100644 index 000000000..70cfeea53 --- /dev/null +++ b/.idea/runConfigurations/rt1010_jlink.xml @@ -0,0 +1,10 @@ + + + + + + + + + \ No newline at end of file diff --git a/.idea/runConfigurations/rt1010_nxplink.xml b/.idea/runConfigurations/rt1010_nxplink.xml deleted file mode 100644 index cf3bf842f..000000000 --- a/.idea/runConfigurations/rt1010_nxplink.xml +++ /dev/null @@ -1,10 +0,0 @@ - - - - - - - - - \ No newline at end of file diff --git a/.idea/runConfigurations/rt1060_nxplink.xml b/.idea/runConfigurations/rt1060_nxplink.xml deleted file mode 100644 index d3303bdb6..000000000 --- a/.idea/runConfigurations/rt1060_nxplink.xml +++ /dev/null @@ -1,10 +0,0 @@ - - - - - - - - - \ No newline at end of file diff --git a/.pre-commit-config.yaml b/.pre-commit-config.yaml index 6fb98afb8..4071ec326 100644 --- a/.pre-commit-config.yaml +++ b/.pre-commit-config.yaml @@ -8,8 +8,16 @@ repos: hooks: - id: check-yaml - id: trailing-whitespace + exclude: | + (?x)^( + hw/bsp/mcx/sdk/ + ) - id: end-of-file-fixer - exclude: ^.idea/ + exclude: | + (?x)^( + .idea/| + hw/bsp/mcx/sdk/ + ) - id: forbid-submodules - repo: https://github.com/codespell-project/codespell @@ -17,7 +25,11 @@ repos: hooks: - id: codespell args: [-w] - exclude: ^lib/ + exclude: | + (?x)^( + lib/| + hw/bsp/mcx/sdk/ + ) - repo: local hooks: diff --git a/examples/device/CMakeLists.txt b/examples/device/CMakeLists.txt index 10a1f4c26..89cfceeeb 100644 --- a/examples/device/CMakeLists.txt +++ b/examples/device/CMakeLists.txt @@ -24,7 +24,7 @@ family_add_subdirectory(midi_test) family_add_subdirectory(msc_dual_lun) # FIXME temp skip net_lwip_webserver for imxrt for now -if (NOT ${FAMILY} STREQUAL "imxrt") +if (NOT ${FAMILY} STREQUAL "imxrt" AND NOT ${FAMILY} STREQUAL "mcx") family_add_subdirectory(net_lwip_webserver) endif() diff --git a/hw/bsp/board_mcu.h b/hw/bsp/board_mcu.h index cd195a19b..35210dbae 100644 --- a/hw/bsp/board_mcu.h +++ b/hw/bsp/board_mcu.h @@ -44,7 +44,7 @@ TU_CHECK_MCU(OPT_MCU_LPC40XX, OPT_MCU_LPC43XX) #include "chip.h" -#elif TU_CHECK_MCU(OPT_MCU_LPC51UXX, OPT_MCU_LPC54XXX, OPT_MCU_LPC55XX) +#elif TU_CHECK_MCU(OPT_MCU_LPC51UXX, OPT_MCU_LPC54XXX, OPT_MCU_LPC55XX, OPT_MCU_MCXN9) #include "fsl_device_registers.h" #elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32) diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index 442aba955..d2d675332 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -135,6 +135,13 @@ function(family_add_default_example_warnings TARGET) endif() endfunction() + +# add_custom_command(TARGET ${TARGET} POST_BUILD +# COMMAND ${CMAKE_OBJCOPY} -O ihex $ ${TARGET}.hex +# COMMAND ${CMAKE_OBJCOPY} -O binary $ ${TARGET}.bin +# COMMENT "Creating ${TARGET}.hex and ${TARGET}.bin" +# ) + # Add flash jlink target function(family_flash_jlink TARGET) if (NOT DEFINED JLINKEXE) diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index 5261e5810..ade744aa5 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -1,8 +1,4 @@ -if (TARGET _imxrt_family_inclusion_marker) - return() -endif () - -add_library(_imxrt_family_inclusion_marker INTERFACE) +include_guard() if (NOT BOARD) message(FATAL_ERROR "BOARD not specified") @@ -87,6 +83,11 @@ function(family_configure_target TARGET) # set output name to .elf set_target_properties(${TARGET} PROPERTIES OUTPUT_NAME ${TARGET}.elf) + # run size after build + add_custom_command(TARGET ${TARGET} POST_BUILD + COMMAND ${TOOLCHAIN_SIZE} $ + ) + # TOP is path to root directory set(TOP "${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../..") diff --git a/hw/bsp/lpc18/boards/lpcxpresso18s37/board.cmake b/hw/bsp/lpc18/boards/lpcxpresso18s37/board.cmake new file mode 100644 index 000000000..b540012a4 --- /dev/null +++ b/hw/bsp/lpc18/boards/lpcxpresso18s37/board.cmake @@ -0,0 +1,11 @@ +set(MCU_VARIANT LPC18S37) + +set(JLINK_DEVICE LPC18S37) +set(PYOCD_TARGET LPC18S37) +set(NXPLINK_DEVICE LPC18S37:LPCXPRESSO18S37) + +set(LD_FILE_gcc ${CMAKE_CURRENT_LIST_DIR}/lpc1837.ld) + +function(update_board TARGET) + # nothing to do +endfunction() diff --git a/hw/bsp/lpc18/boards/mcb1800/board.cmake b/hw/bsp/lpc18/boards/mcb1800/board.cmake new file mode 100644 index 000000000..1efeafd12 --- /dev/null +++ b/hw/bsp/lpc18/boards/mcb1800/board.cmake @@ -0,0 +1,11 @@ +set(MCU_VARIANT LPC1857) + +set(JLINK_DEVICE LPC1857) +set(PYOCD_TARGET LPC1857) +set(NXPLINK_DEVICE LPC1857:MCB1857) + +set(LD_FILE_gcc ${CMAKE_CURRENT_LIST_DIR}/lpc1857.ld) + +function(update_board TARGET) + # nothing to do +endfunction() diff --git a/hw/bsp/lpc18/family.cmake b/hw/bsp/lpc18/family.cmake new file mode 100644 index 000000000..059408fe9 --- /dev/null +++ b/hw/bsp/lpc18/family.cmake @@ -0,0 +1,155 @@ +include_guard() + +if (NOT BOARD) + message(FATAL_ERROR "BOARD not specified") +endif () + +# TOP is path to root directory +set(TOP "${CMAKE_CURRENT_LIST_DIR}/../../..") +set(SDK_DIR ${TOP}/hw/mcu/nxp/lpcopen/lpc18xx/lpc_chip_18xx) + +# toolchain set up +set(CMAKE_SYSTEM_PROCESSOR cortex-m3 CACHE INTERNAL "System Processor") +set(CMAKE_TOOLCHAIN_FILE ${TOP}/tools/cmake/toolchain/arm_${TOOLCHAIN}.cmake) + +set(FAMILY_MCUS LPC18XX CACHE INTERNAL "") + +# include board specific +include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) + + +#------------------------------------ +# BOARD_TARGET +#------------------------------------ +# only need to be built ONCE for all examples +set(BOARD_TARGET board_${BOARD}) +if (NOT TARGET ${BOARD_TARGET}) + add_library(${BOARD_TARGET} STATIC + ${SDK_DIR}/../gcc/cr_startup_lpc18xx.c + ${SDK_DIR}/src/chip_18xx_43xx.c + ${SDK_DIR}/src/clock_18xx_43xx.c + ${SDK_DIR}/src/gpio_18xx_43xx.c + ${SDK_DIR}/src/sysinit_18xx_43xx.c + ${SDK_DIR}/src/uart_18xx_43xx.c + ) + target_compile_options(${BOARD_TARGET} PUBLIC + -nostdlib + ) + target_compile_definitions(${BOARD_TARGET} PUBLIC + __USE_LPCOPEN + CORE_M3 + ) + target_include_directories(${BOARD_TARGET} PUBLIC + ${SDK_DIR}/inc + ${SDK_DIR}/inc/config_18xx + ) + update_board(${BOARD_TARGET}) + + if (NOT DEFINED LD_FILE_${TOOLCHAIN}) + MESSAGE(FATAL_ERROR "LD_FILE_${TOOLCHAIN} not defined") + endif () + + if (TOOLCHAIN STREQUAL "gcc") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--script=${LD_FILE_gcc}" + "LINKER:-Map=$>,$,$>${CMAKE_EXECUTABLE_SUFFIX}.map" + # nanolib + --specs=nosys.specs + --specs=nano.specs + ) + else () + # TODO support IAR + endif () +endif () # BOARD_TARGET + +#------------------------------------ +# Functions +#------------------------------------ +function(family_configure_target TARGET) + # set output name to .elf + set_target_properties(${TARGET} PROPERTIES OUTPUT_NAME ${TARGET}.elf) + + # run size after build + add_custom_command(TARGET ${TARGET} POST_BUILD + COMMAND ${TOOLCHAIN_SIZE} $ + ) + + #---------- Port Specific ---------- + # These files are built for each example since it depends on example's tusb_config.h + target_sources(${TARGET} PUBLIC + # TinyUSB Port + ${TOP}/src/portable/chipidea/ci_hs/dcd_ci_hs.c + ${TOP}/src/portable/chipidea/ci_hs/hcd_ci_hs.c + ${TOP}/src/portable/ehci/ehci.c + # BSP + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c + ) + target_include_directories(${TARGET} PUBLIC + # family, hw, board + ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../ + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} + ) + + #---------- TinyUSB ---------- + # tinyusb target is built for each example since it depends on example's tusb_config.h + set(TINYUSB_TARGET_PREFIX ${TARGET}-) + add_library(${TARGET}-tinyusb_config INTERFACE) + + target_include_directories(${TARGET}-tinyusb_config INTERFACE + ${CMAKE_CURRENT_SOURCE_DIR}/src + ) + target_compile_definitions(${TARGET}-tinyusb_config INTERFACE + CFG_TUSB_MCU=OPT_MCU_LPC18XX + ) + + # tinyusb's CMakeList.txt + add_subdirectory(${TOP}/src ${CMAKE_CURRENT_BINARY_DIR}/tinyusb) + + # Link dependencies + target_link_libraries(${TARGET} PUBLIC ${BOARD_TARGET} ${TARGET}-tinyusb) + + # group target (not yet supported by clion) + set_target_properties(${TARGET}-tinyusb ${TARGET}-tinyusb_config + PROPERTIES FOLDER ${TARGET}_sub + ) + + #---------- Flash ---------- + family_flash_jlink(${TARGET}) +endfunction() + + +function(family_add_freertos TARGET) + # freertos_config + add_subdirectory(${CMAKE_CURRENT_FUNCTION_LIST_DIR}/FreeRTOSConfig ${CMAKE_CURRENT_BINARY_DIR}/freertos_config) + + ## freertos + if (NOT TARGET freertos_kernel) + add_subdirectory(${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../../lib/FreeRTOS-Kernel ${CMAKE_CURRENT_BINARY_DIR}/freertos_kernel) + endif () + + # Add FreeRTOS option to tinyusb_config + target_compile_definitions(${TARGET}-tinyusb_config INTERFACE + CFG_TUSB_OS=OPT_OS_FREERTOS + ) + # link tinyusb with freeRTOS kernel + target_link_libraries(${TARGET}-tinyusb PUBLIC + freertos_kernel + ) + target_link_libraries(${TARGET} PUBLIC + freertos_kernel + ) +endfunction() + +function(family_configure_device_example TARGET) + family_configure_target(${TARGET}) +endfunction() + +function(family_configure_host_example TARGET) + family_configure_target(${TARGET}) +endfunction() + +function(family_configure_dual_usb_example TARGET) + family_configure_target(${TARGET}) +endfunction() diff --git a/hw/bsp/lpc55/family.cmake b/hw/bsp/lpc55/family.cmake index 611c88eb5..3aeda5b2d 100644 --- a/hw/bsp/lpc55/family.cmake +++ b/hw/bsp/lpc55/family.cmake @@ -1,8 +1,4 @@ -if (TARGET _lpc55_family_inclusion_marker) - return() -endif () - -add_library(_lpc55_family_inclusion_marker INTERFACE) +include_guard() if (NOT BOARD) message(FATAL_ERROR "BOARD not specified") diff --git a/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h new file mode 100644 index 000000000..4c6058d27 --- /dev/null +++ b/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h @@ -0,0 +1,166 @@ +/* + * FreeRTOS Kernel V10.0.0 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. If you wish to use our Amazon + * FreeRTOS name, please do so in a fair use way that does not cause confusion. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + + +#ifndef FREERTOS_CONFIG_H +#define FREERTOS_CONFIG_H + +/*----------------------------------------------------------- + * Application specific definitions. + * + * These definitions should be adjusted for your particular hardware and + * application requirements. + * + * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE + * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. + * + * See http://www.freertos.org/a00110.html. + *----------------------------------------------------------*/ + +// IAR assembler have limited preprocessor support and it only need following macros: +#ifndef __IASMARM__ +// FIXME cause redundant-decls warnings +extern uint32_t SystemCoreClock; +#endif + +/* Cortex M23/M33 port configuration. */ +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE ( 1024 ) + +#define configUSE_PREEMPTION 1 +#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 +#define configCPU_CLOCK_HZ SystemCoreClock +#define configTICK_RATE_HZ ( 1000 ) +#define configMAX_PRIORITIES ( 5 ) +#define configMINIMAL_STACK_SIZE ( 128 ) +#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) +#define configMAX_TASK_NAME_LEN 16 +#define configUSE_16_BIT_TICKS 0 +#define configIDLE_SHOULD_YIELD 1 +#define configUSE_MUTEXES 1 +#define configUSE_RECURSIVE_MUTEXES 1 +#define configUSE_COUNTING_SEMAPHORES 1 +#define configQUEUE_REGISTRY_SIZE 2 +#define configUSE_QUEUE_SETS 0 +#define configUSE_TIME_SLICING 0 +#define configUSE_NEWLIB_REENTRANT 0 +#define configENABLE_BACKWARD_COMPATIBILITY 1 +#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 + +#define configSUPPORT_STATIC_ALLOCATION 0 +#define configSUPPORT_DYNAMIC_ALLOCATION 1 + +/* Hook function related definitions. */ +#define configUSE_IDLE_HOOK 0 +#define configUSE_TICK_HOOK 0 +#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning +#define configCHECK_FOR_STACK_OVERFLOW 2 + +/* Run time and task stats gathering related definitions. */ +#define configGENERATE_RUN_TIME_STATS 0 +#define configRECORD_STACK_HIGH_ADDRESS 1 +#define configUSE_TRACE_FACILITY 1 // legacy trace +#define configUSE_STATS_FORMATTING_FUNCTIONS 0 + +/* Co-routine definitions. */ +#define configUSE_CO_ROUTINES 0 +#define configMAX_CO_ROUTINE_PRIORITIES 2 + +/* Software timer related definitions. */ +#define configUSE_TIMERS 1 +#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) +#define configTIMER_QUEUE_LENGTH 32 +#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE + +/* Optional functions - most linkers will remove unused functions anyway. */ +#define INCLUDE_vTaskPrioritySet 0 +#define INCLUDE_uxTaskPriorityGet 0 +#define INCLUDE_vTaskDelete 0 +#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY +#define INCLUDE_xResumeFromISR 0 +#define INCLUDE_vTaskDelayUntil 1 +#define INCLUDE_vTaskDelay 1 +#define INCLUDE_xTaskGetSchedulerState 0 +#define INCLUDE_xTaskGetCurrentTaskHandle 1 +#define INCLUDE_uxTaskGetStackHighWaterMark 0 +#define INCLUDE_xTaskGetIdleTaskHandle 0 +#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 +#define INCLUDE_pcTaskGetTaskName 0 +#define INCLUDE_eTaskGetState 0 +#define INCLUDE_xEventGroupSetBitFromISR 0 +#define INCLUDE_xTimerPendFunctionCall 0 + +/* Define to trap errors during development. */ +// Halt CPU (breakpoint) when hitting error, only apply for Cortex M3, M4, M7 +#if defined(__ARM_ARCH_7M__) || defined (__ARM_ARCH_7EM__) + #define configASSERT(_exp) \ + do {\ + if ( !(_exp) ) { \ + volatile uint32_t* ARM_CM_DHCSR = ((volatile uint32_t*) 0xE000EDF0UL); /* Cortex M CoreDebug->DHCSR */ \ + if ( (*ARM_CM_DHCSR) & 1UL ) { /* Only halt mcu if debugger is attached */ \ + taskDISABLE_INTERRUPTS(); \ + __asm("BKPT #0\n"); \ + }\ + }\ + } while(0) +#else + #define configASSERT( x ) +#endif + +/* FreeRTOS hooks to NVIC vectors */ +#define xPortPendSVHandler PendSV_Handler +#define xPortSysTickHandler SysTick_Handler +#define vPortSVCHandler SVC_Handler + +//--------------------------------------------------------------------+ +// Interrupt nesting behavior configuration. +//--------------------------------------------------------------------+ + +// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header +#define configPRIO_BITS 3 + +/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1<FRO192M_CTRL |= ANACTRL_FRO192M_CTRL_USBCLKADJ_MASK; + CLOCK_SetClkDiv(kCLOCK_DivUsb0Clk, 1, false); + CLOCK_AttachClk(kFRO_HF_to_USB0_CLK); + + /*According to reference manual, device mode setting has to be set by access usb host register */ + CLOCK_EnableClock(kCLOCK_Usbhsl0); // enable usb0 host clock + USBFSH->PORTMODE |= USBFSH_PORTMODE_DEV_ENABLE_MASK; + CLOCK_DisableClock(kCLOCK_Usbhsl0); // disable usb0 host clock + + /* enable USB Device clock */ + CLOCK_EnableUsbfs0DeviceClock(kCLOCK_UsbfsSrcFro, CLOCK_GetFreq(kCLOCK_FroHf)); +#endif + +#if PORT_SUPPORT_DEVICE(1) + // Port1 is High Speed + + // Power + SPC0->ACTIVE_VDELAY = 0x0500; + /* Change the power DCDC to 1.8v (By default, DCDC is 1.8V), CORELDO to 1.1v (By default, CORELDO is 1.0V) */ + SPC0->ACTIVE_CFG &= ~SPC_ACTIVE_CFG_CORELDO_VDD_DS_MASK; + SPC0->ACTIVE_CFG |= SPC_ACTIVE_CFG_DCDC_VDD_LVL(0x3) | SPC_ACTIVE_CFG_CORELDO_VDD_LVL(0x3) | + SPC_ACTIVE_CFG_SYSLDO_VDD_DS_MASK | SPC_ACTIVE_CFG_DCDC_VDD_DS(0x2u); + /* Wait until it is done */ + while (SPC0->SC & SPC_SC_BUSY_MASK) {} + if (0u == (SCG0->LDOCSR & SCG_LDOCSR_LDOEN_MASK)) { + SCG0->TRIM_LOCK = 0x5a5a0001U; + SCG0->LDOCSR |= SCG_LDOCSR_LDOEN_MASK; + /* wait LDO ready */ + while (0U == (SCG0->LDOCSR & SCG_LDOCSR_VOUT_OK_MASK)); + } + SYSCON->AHBCLKCTRLSET[2] |= SYSCON_AHBCLKCTRL2_USB_HS_MASK | SYSCON_AHBCLKCTRL2_USB_HS_PHY_MASK; + SCG0->SOSCCFG &= ~(SCG_SOSCCFG_RANGE_MASK | SCG_SOSCCFG_EREFS_MASK); + /* xtal = 20 ~ 30MHz */ + SCG0->SOSCCFG = (1U << SCG_SOSCCFG_RANGE_SHIFT) | (1U << SCG_SOSCCFG_EREFS_SHIFT); + SCG0->SOSCCSR |= SCG_SOSCCSR_SOSCEN_MASK; + while (1) { + if (SCG0->SOSCCSR & SCG_SOSCCSR_SOSCVLD_MASK) { + break; + } + } + + // Clock + SYSCON->CLOCK_CTRL |= SYSCON_CLOCK_CTRL_CLKIN_ENA_MASK | SYSCON_CLOCK_CTRL_CLKIN_ENA_FM_USBH_LPT_MASK; + CLOCK_EnableClock(kCLOCK_UsbHs); + CLOCK_EnableClock(kCLOCK_UsbHsPhy); + CLOCK_EnableUsbhsPhyPllClock(kCLOCK_Usbphy480M, 24000000U); + CLOCK_EnableUsbhsClock(); + + // USB PHY +#if ((!(defined FSL_FEATURE_SOC_CCM_ANALOG_COUNT)) && (!(defined FSL_FEATURE_SOC_ANATOP_COUNT))) + USBPHY->TRIM_OVERRIDE_EN = 0x001fU; /* override IFR value */ +#endif + + // Enable PHY support for Low speed device + LS via FS Hub + USBPHY->CTRL |= USBPHY_CTRL_SET_ENUTMILEVEL2_MASK | USBPHY_CTRL_SET_ENUTMILEVEL3_MASK; + + // Enable all power for normal operation + USBPHY->PWD = 0; + + // TX Timing + uint32_t phytx = USBPHY->TX; + phytx &= ~(USBPHY_TX_D_CAL_MASK | USBPHY_TX_TXCAL45DM_MASK | USBPHY_TX_TXCAL45DP_MASK); + phytx |= USBPHY_TX_D_CAL(0x04) | USBPHY_TX_TXCAL45DP(0x07) | USBPHY_TX_TXCAL45DM(0x07); + //phytx |= USBPHY_TX_D_CAL(0x0C) | USBPHY_TX_TXCAL45DP(0x06) | USBPHY_TX_TXCAL45DM(0x06); + USBPHY->TX = phytx; +#endif +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); + +#ifdef NEOPIXEL_PIN + if (state) { + sctpix_setPixel(NEOPIXEL_CH, 0, 0x100000); + sctpix_setPixel(NEOPIXEL_CH, 1, 0x101010); + } else { + sctpix_setPixel(NEOPIXEL_CH, 0, 0x001000); + sctpix_setPixel(NEOPIXEL_CH, 1, 0x000010); + } + sctpix_show(); +#endif +} + +uint32_t board_button_read(void) +{ +#ifdef BUTTON_GPIO + return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); +#endif +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ +#ifdef UART_DEV + LPUART_WriteBlocking(UART_DEV, (uint8_t const *) buf, len); + return len; +#else + (void) buf; (void) len; + return 0; +#endif +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif diff --git a/hw/bsp/mcx/family.cmake b/hw/bsp/mcx/family.cmake new file mode 100644 index 000000000..e4bc11be5 --- /dev/null +++ b/hw/bsp/mcx/family.cmake @@ -0,0 +1,179 @@ +include_guard() + +if (NOT BOARD) + message(FATAL_ERROR "BOARD not specified") +endif () + +# TOP is path to root directory +set(TOP ${CMAKE_CURRENT_LIST_DIR}/../../..) +set(SDK_DIR ${TOP}/hw/mcu/nxp/mcux-sdk) +set(CMSIS_DIR ${TOP}/lib/CMSIS_5) + +# toolchain set up +set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor") +set(CMAKE_TOOLCHAIN_FILE ${TOP}/tools/cmake/toolchain/arm_${TOOLCHAIN}.cmake) + +set(FAMILY_MCUS LPC55XX CACHE INTERNAL "") + +# include board specific +include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) + + +#------------------------------------ +# BOARD_TARGET +#------------------------------------ +# only need to be built ONCE for all examples +set(BOARD_TARGET board_${BOARD}) +if (NOT TARGET ${BOARD_TARGET}) + add_library(${BOARD_TARGET} STATIC + # external driver + #lib/sct_neopixel/sct_neopixel.c + + # driver + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_gpio.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_common_arm.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpuart.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpflexcomm.c + # mcu + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_reset.c + ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_CORE}.c + ) +# target_compile_definitions(${BOARD_TARGET} PUBLIC +# ) + target_include_directories(${BOARD_TARGET} PUBLIC + # driver + # mcu + ${CMSIS_DIR}/CMSIS/Core/Include + ${SDK_DIR}/devices/${MCU_VARIANT} + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers + ) + update_board(${BOARD_TARGET}) + + if (TOOLCHAIN STREQUAL "gcc") + target_sources(${BOARD_TARGET} PUBLIC + ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_CORE}.S + ) + target_link_options(${BOARD_TARGET} PUBLIC + # linker file + "LINKER:--script=${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_CORE}_flash.ld" + # link map + "LINKER:-Map=$>,$,$>${CMAKE_EXECUTABLE_SUFFIX}.map" + # nanolib + --specs=nosys.specs + --specs=nano.specs + ) + else () + # TODO support IAR + endif () +endif () # BOARD_TARGET + +#------------------------------------ +# Functions +#------------------------------------ +function(family_configure_target TARGET) + # set output name to .elf + set_target_properties(${TARGET} PROPERTIES OUTPUT_NAME ${TARGET}.elf) + + # run size after build + add_custom_command(TARGET ${TARGET} POST_BUILD + COMMAND ${TOOLCHAIN_SIZE} $ + ) + + # TOP is path to root directory + set(TOP "${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../..") + + #---------- Port Specific ---------- + # These files are built for each example since it depends on example's tusb_config.h + target_sources(${TARGET} PUBLIC + # TinyUSB Port + ${TOP}/src/portable/chipidea/ci_hs/dcd_ci_hs.c + # BSP + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c + ) + target_include_directories(${TARGET} PUBLIC + # family, hw, board + ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../ + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} + ) + + #---------- TinyUSB ---------- + # tinyusb target is built for each example since it depends on example's tusb_config.h + set(TINYUSB_TARGET_PREFIX ${TARGET}-) + add_library(${TARGET}-tinyusb_config INTERFACE) + + target_include_directories(${TARGET}-tinyusb_config INTERFACE + ${CMAKE_CURRENT_SOURCE_DIR}/src + ) + target_compile_definitions(${TARGET}-tinyusb_config INTERFACE + CFG_TUSB_MCU=OPT_MCU_MCXN9 + ) + + # tinyusb's CMakeList.txt + add_subdirectory(${TOP}/src ${CMAKE_CURRENT_BINARY_DIR}/tinyusb) + + # Link dependencies + target_link_libraries(${TARGET} PUBLIC ${BOARD_TARGET} ${TARGET}-tinyusb) + + # group target (not yet supported by clion) + set_target_properties(${TARGET}-tinyusb ${TARGET}-tinyusb_config + PROPERTIES FOLDER ${TARGET}_sub + ) + + #---------- Flash ---------- + # use MCUXpresso GUI Flash Tool to flash the elf + +# set(REDLINK_EXE /usr/local/LinkServer/binaries/crt_emu_cm_redlink) +# add_custom_target(${TARGET}-redlink +# DEPENDS ${TARGET} +# COMMAND ${REDLINK_EXE} --flash-load-exec $ --vendor NXP -p MCXN947 --bootromstall +# 0x50000040 -CoreIndex=0 --flash-driver= -x ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/flash --flash-dir +# ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/flash --flash-hashing +# ) + + #family_flash_jlink(${TARGET}) + #family_flash_nxplink(${TARGET}) + #family_flash_pyocd(${TARGET}) +endfunction() + + +function(family_add_freertos TARGET) + # freertos_config + if (NOT TARGET freertos_config) + add_library(freertos_config INTERFACE) + target_include_directories(freertos_config SYSTEM INTERFACE + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/FreeRTOSConfig + ) + endif() + + ## freertos + if (NOT TARGET freertos_kernel) + add_subdirectory(${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../../lib/FreeRTOS-Kernel ${CMAKE_CURRENT_BINARY_DIR}/freertos_kernel) + endif () + + # Add FreeRTOS option to tinyusb_config + target_compile_definitions(${TARGET}-tinyusb_config INTERFACE + CFG_TUSB_OS=OPT_OS_FREERTOS + ) + # link tinyusb with freeRTOS kernel + target_link_libraries(${TARGET}-tinyusb PUBLIC + freertos_kernel + ) + target_link_libraries(${TARGET} PUBLIC + freertos_kernel + ) +endfunction() + +function(family_configure_device_example TARGET) + family_configure_target(${TARGET}) +endfunction() + +function(family_configure_host_example TARGET) + family_configure_target(${TARGET}) +endfunction() + +function(family_configure_dual_usb_example TARGET) + family_configure_target(${TARGET}) +endfunction() diff --git a/hw/bsp/mcx/family.mk b/hw/bsp/mcx/family.mk new file mode 100644 index 000000000..2cd4c2448 --- /dev/null +++ b/hw/bsp/mcx/family.mk @@ -0,0 +1,48 @@ +UF2_FAMILY_ID = 0x2abc77ec +SDK_DIR = hw/mcu/nxp/mcux-sdk + +DEPS_SUBMODULES += $(SDK_DIR) lib/CMSIS_5 + +include $(TOP)/$(BOARD_PATH)/board.mk + +CPU_CORE ?= cortex-m33 +include $(TOP)/tools/make/cpu/$(CPU_CORE).mk + +# Default to Highspeed PORT1 +PORT ?= 1 + +CFLAGS += \ + -flto \ + -DCFG_TUSB_MCU=OPT_MCU_MCXN9 \ + -DBOARD_TUD_RHPORT=$(PORT) \ + +ifeq ($(PORT), 1) + $(info "PORT1 High Speed") + CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED +else + $(info "PORT0 Full Speed") +endif + +# mcu driver cause following warnings +CFLAGS += -Wno-error=unused-parameter -Wno-error=old-style-declaration + +# All source paths should be relative to the top level. +LD_FILE ?= $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/$(MCU_CORE)_flash.ld + +SRC_C += \ + src/portable/chipidea/ci_hs/dcd_ci_hs.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/system_$(MCU_CORE).c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_clock.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_reset.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_gpio.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_common_arm.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpflexcomm.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpuart.c \ + +INC += \ + $(TOP)/$(BOARD_PATH) \ + $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ + $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT) \ + $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers \ + +SRC_S += $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/startup_$(MCU_CORE).S diff --git a/hw/bsp/nrf/family.cmake b/hw/bsp/nrf/family.cmake index 9c43478e8..1156a171b 100644 --- a/hw/bsp/nrf/family.cmake +++ b/hw/bsp/nrf/family.cmake @@ -1,8 +1,4 @@ -if (TARGET _nrf_family_inclusion_marker) - return() -endif () - -add_library(_nrf_family_inclusion_marker INTERFACE) +include_guard() if (NOT BOARD) message(FATAL_ERROR "BOARD not specified") @@ -89,6 +85,11 @@ function(family_configure_target TARGET) # set output name to .elf set_target_properties(${TARGET} PROPERTIES OUTPUT_NAME ${TARGET}.elf) + # run size after build + add_custom_command(TARGET ${TARGET} POST_BUILD + COMMAND ${TOOLCHAIN_SIZE} $ + ) + # TOP is path to root directory set(TOP "${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../..") diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index ba8976a8c..9c2933983 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -59,14 +59,6 @@ #define TUP_USBIP_OHCI #define TUP_OHCI_RHPORTS 2 -#elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) - // TODO USB0 has 6, USB1 has 4 - #define TUP_USBIP_CHIPIDEA_HS - #define TUP_USBIP_EHCI - - #define TUP_DCD_ENDPOINT_MAX 6 - #define TUP_RHPORT_HIGHSPEED 1 // Port0 HS, Port1 FS - #elif TU_CHECK_MCU(OPT_MCU_LPC51UXX) #define TUP_DCD_ENDPOINT_MAX 5 @@ -78,12 +70,28 @@ // TODO USB0 has 5, USB1 has 6 #define TUP_DCD_ENDPOINT_MAX 6 +#elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) + // USB0 has 6 with HS PHY, USB1 has 4 only FS + #define TUP_USBIP_CHIPIDEA_HS + #define TUP_USBIP_EHCI + + #define TUP_DCD_ENDPOINT_MAX 6 + #define TUP_RHPORT_HIGHSPEED 1 + +#elif TU_CHECK_MCU(OPT_MCU_MCXN9) + // NOTE: MCXN943 port 1 use chipidea HS, port 0 use chipidea FS + #define TUP_USBIP_CHIPIDEA_HS + #define TUP_USBIP_EHCI + + #define TUP_DCD_ENDPOINT_MAX 8 + #define TUP_RHPORT_HIGHSPEED 1 + #elif TU_CHECK_MCU(OPT_MCU_MIMXRT) #define TUP_USBIP_CHIPIDEA_HS #define TUP_USBIP_EHCI #define TUP_DCD_ENDPOINT_MAX 8 - #define TUP_RHPORT_HIGHSPEED 1 // Port0 HS, Port1 HS + #define TUP_RHPORT_HIGHSPEED 1 #elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32) #define TUP_USBIP_CHIPIDEA_FS diff --git a/src/device/dcd.h b/src/device/dcd.h index 00419ff05..f82b8633d 100644 --- a/src/device/dcd.h +++ b/src/device/dcd.h @@ -102,6 +102,22 @@ typedef struct TU_ATTR_ALIGNED(4) //TU_VERIFY_STATIC(sizeof(dcd_event_t) <= 12, "size is not correct"); +//--------------------------------------------------------------------+ +// Memory API +//--------------------------------------------------------------------+ + +// clean/flush data cache: write cache -> memory. +// Required before an DMA TX transfer to make sure data is in memory +void dcd_dcache_clean(void* addr, uint32_t data_size) TU_ATTR_WEAK; + +// invalidate data cache: mark cache as invalid, next read will read from memory +// Required BOTH before and after an DMA RX transfer +void dcd_dcache_invalidate(void* addr, uint32_t data_size) TU_ATTR_WEAK; + +// clean and invalidate data cache +// Required before an DMA transfer where memory is both read/write by DMA +void dcd_dcache_clean_invalidate(void* addr, uint32_t data_size) TU_ATTR_WEAK; + //--------------------------------------------------------------------+ // Controller API //--------------------------------------------------------------------+ diff --git a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h index 607926a65..ceff893bd 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h +++ b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h @@ -46,18 +46,44 @@ static const ci_hs_controller_t _ci_controller[] = { // RT1010 and RT1020 only has 1 USB controller #if FSL_FEATURE_SOC_USBHS_COUNT == 1 - { .reg_base = USB_BASE , .irqnum = USB_OTG1_IRQn, .ep_count = 8 } + { .reg_base = USB_BASE , .irqnum = USB_OTG1_IRQn } #else - { .reg_base = USB1_BASE, .irqnum = USB_OTG1_IRQn, .ep_count = 8 }, - { .reg_base = USB2_BASE, .irqnum = USB_OTG2_IRQn, .ep_count = 8 } + { .reg_base = USB1_BASE, .irqnum = USB_OTG1_IRQn}, + { .reg_base = USB2_BASE, .irqnum = USB_OTG2_IRQn} #endif }; +#define CI_HS_REG(_port) ((ci_hs_regs_t*) _ci_controller[_port].reg_base) + +//------------- DCD -------------// #define CI_DCD_INT_ENABLE(_p) NVIC_EnableIRQ (_ci_controller[_p].irqnum) #define CI_DCD_INT_DISABLE(_p) NVIC_DisableIRQ(_ci_controller[_p].irqnum) +//------------- HCD -------------// #define CI_HCD_INT_ENABLE(_p) NVIC_EnableIRQ (_ci_controller[_p].irqnum) #define CI_HCD_INT_DISABLE(_p) NVIC_DisableIRQ(_ci_controller[_p].irqnum) +//------------- DCache -------------// +TU_ATTR_ALWAYS_INLINE static inline bool imxrt_is_cache_mem(uint32_t addr) { + return !(0x20000000 <= addr && addr < 0x20100000); +} + +TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_clean(void* addr, uint32_t data_size) { + if (imxrt_is_cache_mem((uint32_t) addr)) { + SCB_CleanDCache_by_Addr((uint32_t *) addr, (int32_t) data_size); + } +} + +TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_invalidate(void* addr, uint32_t data_size) { + if (imxrt_is_cache_mem((uint32_t) addr)) { + SCB_InvalidateDCache_by_Addr(addr, (int32_t) data_size); + } +} + +TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_clean_invalidate(void* addr, uint32_t data_size) { + if (imxrt_is_cache_mem((uint32_t) addr)) { + SCB_CleanInvalidateDCache_by_Addr(addr, (int32_t) data_size); + } +} #endif diff --git a/src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h b/src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h index 8c2e7dfa6..2e84c93e7 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h +++ b/src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h @@ -32,10 +32,12 @@ static const ci_hs_controller_t _ci_controller[] = { - { .reg_base = LPC_USB0_BASE, .irqnum = USB0_IRQn, .ep_count = 6 }, - { .reg_base = LPC_USB1_BASE, .irqnum = USB1_IRQn, .ep_count = 4 } + { .reg_base = LPC_USB0_BASE, .irqnum = USB0_IRQn }, + { .reg_base = LPC_USB1_BASE, .irqnum = USB1_IRQn } }; +#define CI_HS_REG(_port) ((ci_hs_regs_t*) _ci_controller[_port].reg_base) + #define CI_DCD_INT_ENABLE(_p) NVIC_EnableIRQ (_ci_controller[_p].irqnum) #define CI_DCD_INT_DISABLE(_p) NVIC_DisableIRQ(_ci_controller[_p].irqnum) diff --git a/src/portable/chipidea/ci_hs/ci_hs_mcx.h b/src/portable/chipidea/ci_hs/ci_hs_mcx.h new file mode 100644 index 000000000..f940f4a9d --- /dev/null +++ b/src/portable/chipidea/ci_hs/ci_hs_mcx.h @@ -0,0 +1,52 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2021, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _CI_HS_MCX_H_ +#define _CI_HS_MCX_H_ + +#include "fsl_device_registers.h" + +// NOTE: MCX N9 has 2 different USB Controller +// - USB0 is KHCI FullSpeed +// - USB1 is ChipIdea HighSpeed, therefore rhport = 1 is actually index 0 + +static const ci_hs_controller_t _ci_controller[] = { + {.reg_base = USBHS1__USBC_BASE, .irqnum = USB1_HS_IRQn} +}; + +TU_ATTR_ALWAYS_INLINE static inline ci_hs_regs_t* CI_HS_REG(uint8_t port) { + (void) port; + return ((ci_hs_regs_t*) _ci_controller[0].reg_base); +} + +#define CI_DCD_INT_ENABLE(_p) do { (void) _p; NVIC_EnableIRQ (_ci_controller[0].irqnum); } while (0) +#define CI_DCD_INT_DISABLE(_p) do { (void) _p; NVIC_DisableIRQ(_ci_controller[0].irqnum); } while (0) + +#define CI_HCD_INT_ENABLE(_p) NVIC_EnableIRQ (_ci_controller[_p].irqnum) +#define CI_HCD_INT_DISABLE(_p) NVIC_DisableIRQ(_ci_controller[_p].irqnum) + + +#endif diff --git a/src/portable/chipidea/ci_hs/ci_hs_type.h b/src/portable/chipidea/ci_hs/ci_hs_type.h index 31b5a012d..2f3aa3694 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_type.h +++ b/src/portable/chipidea/ci_hs/ci_hs_type.h @@ -31,13 +31,21 @@ extern "C" { #endif +// DCCPARAMS +enum { + DCCPARAMS_DEN_MASK = 0x1Fu, ///< DEN bit 4:0 +}; + // USBCMD enum { USBCMD_RUN_STOP = TU_BIT(0), USBCMD_RESET = TU_BIT(1), USBCMD_SETUP_TRIPWIRE = TU_BIT(13), - USBCMD_ADD_QTD_TRIPWIRE = TU_BIT(14) ///< This bit is used as a semaphore to ensure the to proper addition of a new dTD to an active (primed) endpoint’s linked list. This bit is set and cleared by software during the process of adding a new dTD -// Interrupt Threshold bit 23:16 + USBCMD_ADD_QTD_TRIPWIRE = TU_BIT(14), // This bit is used as a semaphore to ensure the to proper addition of a + // new dTD to an active (primed) endpoint’s linked list. This bit is set and + // cleared by software during the process of adding a new dTD + + USBCMD_INTR_THRESHOLD_MASK = 0x00FF0000u, // Interrupt Threshold bit 23:16 }; // PORTSC1 @@ -72,6 +80,7 @@ enum { // USBMode enum { + USBMOD_CM_MASK = TU_BIT(0) | TU_BIT(1), USBMODE_CM_DEVICE = 2, USBMODE_CM_HOST = 3, @@ -134,7 +143,6 @@ typedef struct { uint32_t reg_base; uint32_t irqnum; - uint8_t ep_count; // Max bi-directional Endpoints }ci_hs_controller_t; #ifdef __cplusplus diff --git a/src/portable/chipidea/ci_hs/dcd_ci_hs.c b/src/portable/chipidea/ci_hs/dcd_ci_hs.c index 9be79a2f1..850c82e43 100644 --- a/src/portable/chipidea/ci_hs/dcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/dcd_ci_hs.c @@ -28,34 +28,52 @@ #if CFG_TUD_ENABLED && defined(TUP_USBIP_CHIPIDEA_HS) -//--------------------------------------------------------------------+ -// INCLUDE -//--------------------------------------------------------------------+ #include "device/dcd.h" #include "ci_hs_type.h" #if CFG_TUSB_MCU == OPT_MCU_MIMXRT #include "ci_hs_imxrt.h" -#elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) + + void dcd_dcache_clean(void* addr, uint32_t data_size) { + imxrt_dcache_clean(addr, data_size); + } + + void dcd_dcache_invalidate(void* addr, uint32_t data_size) { + imxrt_dcache_invalidate(addr, data_size); + } + + void dcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { + imxrt_dcache_clean_invalidate(addr, data_size); + } + +#else + +#if TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) #include "ci_hs_lpc18_43.h" + +#elif TU_CHECK_MCU(OPT_MCU_MCXN9) + // MCX N9 only port 1 use this controller + #include "ci_hs_mcx.h" #else #error "Unsupported MCUs" #endif -//--------------------------------------------------------------------+ -// MACRO CONSTANT TYPEDEF -//--------------------------------------------------------------------+ + TU_ATTR_WEAK void dcd_dcache_clean(void* addr, uint32_t data_size) { + (void) addr; (void) data_size; + } -#define CI_HS_REG(_port) ((ci_hs_regs_t*) _ci_controller[_port].reg_base) + TU_ATTR_WEAK void dcd_dcache_invalidate(void* addr, uint32_t data_size) { + (void) addr; (void) data_size; + } -// Clean means to push any cached changes to RAM and invalidate "removes" the -// entry from the cache. -#if defined(__CORTEX_M) && __CORTEX_M == 7 && __DCACHE_PRESENT == 1 - #define CleanInvalidateDCache_by_Addr SCB_CleanInvalidateDCache_by_Addr -#else - #define CleanInvalidateDCache_by_Addr(_addr, _dsize) + TU_ATTR_WEAK void dcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { + (void) addr; (void) data_size; + } #endif +//--------------------------------------------------------------------+ +// MACRO CONSTANT TYPEDEF +//--------------------------------------------------------------------+ // ENDPTCTRL enum { @@ -160,6 +178,16 @@ typedef struct { CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(2048) static dcd_data_t _dcd_data; +//--------------------------------------------------------------------+ +// Prototypes and Helper Functions +//--------------------------------------------------------------------+ + +TU_ATTR_ALWAYS_INLINE +static inline uint8_t ci_ep_count(ci_hs_regs_t const* dcd_reg) +{ + return dcd_reg->DCCPARAMS & DCCPARAMS_DEN_MASK; +} + //--------------------------------------------------------------------+ // Controller API //--------------------------------------------------------------------+ @@ -174,7 +202,8 @@ static void bus_reset(uint8_t rhport) // endpoint type of the unused direction must be changed from the control type to any other // type (e.g. bulk). Leaving an un-configured endpoint control will cause undefined behavior // for the data PID tracking on the active endpoint. - for( uint8_t i=1; i < _ci_controller[rhport].ep_count; i++) + uint8_t const ep_count = ci_ep_count(dcd_reg); + for( uint8_t i=1; i < ep_count; i++) { dcd_reg->ENDPTCTRL[i] = (TUSB_XFER_BULK << ENDPTCTRL_TYPE_POS) | (TUSB_XFER_BULK << (16+ENDPTCTRL_TYPE_POS)); } @@ -202,7 +231,7 @@ static void bus_reset(uint8_t rhport) _dcd_data.qhd[0][0].int_on_setup = 1; // OUT only - CleanInvalidateDCache_by_Addr((uint32_t*) &_dcd_data, sizeof(dcd_data_t)); + dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); } void dcd_init(uint8_t rhport) @@ -211,26 +240,34 @@ void dcd_init(uint8_t rhport) ci_hs_regs_t* dcd_reg = CI_HS_REG(rhport); + TU_ASSERT(ci_ep_count(dcd_reg) <= TUP_DCD_ENDPOINT_MAX, ); + // Reset controller dcd_reg->USBCMD |= USBCMD_RESET; while( dcd_reg->USBCMD & USBCMD_RESET ) {} // Set mode to device, must be set immediately after reset - dcd_reg->USBMODE = USBMODE_CM_DEVICE; + uint32_t usbmode = dcd_reg->USBMODE & ~USBMOD_CM_MASK; + usbmode |= USBMODE_CM_DEVICE; + dcd_reg->USBMODE = usbmode; + dcd_reg->OTGSC = OTGSC_VBUS_DISCHARGE | OTGSC_OTG_TERMINATION; #if !TUD_OPT_HIGH_SPEED dcd_reg->PORTSC1 = PORTSC1_FORCE_FULL_SPEED; #endif - CleanInvalidateDCache_by_Addr((uint32_t*) &_dcd_data, sizeof(dcd_data_t)); + dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); dcd_reg->ENDPTLISTADDR = (uint32_t) _dcd_data.qhd; // Endpoint List Address has to be 2K alignment dcd_reg->USBSTS = dcd_reg->USBSTS; dcd_reg->USBINTR = INTR_USB | INTR_ERROR | INTR_PORT_CHANGE | INTR_SUSPEND; - dcd_reg->USBCMD &= ~0x00FF0000; // Interrupt Threshold Interval = 0 - dcd_reg->USBCMD |= USBCMD_RUN_STOP; // Connect + uint32_t usbcmd = dcd_reg->USBCMD; + usbcmd &= ~USBCMD_INTR_THRESHOLD_MASK; // Interrupt Threshold Interval = 0 + usbcmd |= USBCMD_RUN_STOP; // run + + dcd_reg->USBCMD = usbcmd; } void dcd_int_enable(uint8_t rhport) @@ -286,7 +323,7 @@ static void qtd_init(dcd_qtd_t* p_qtd, void * data_ptr, uint16_t total_bytes) { // Force the CPU to flush the buffer. We increase the size by 31 because the call aligns the // address to 32-byte boundaries. Buffer must be word aligned - CleanInvalidateDCache_by_Addr((uint32_t*) tu_align((uint32_t) data_ptr, 4), total_bytes + 31); + dcd_dcache_clean_invalidate((uint32_t*) tu_align((uint32_t) data_ptr, 4), total_bytes + 31); tu_memclr(p_qtd, sizeof(dcd_qtd_t)); @@ -343,8 +380,10 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) uint8_t const epnum = tu_edpt_number(p_endpoint_desc->bEndpointAddress); uint8_t const dir = tu_edpt_dir(p_endpoint_desc->bEndpointAddress); + ci_hs_regs_t* dcd_reg = CI_HS_REG(rhport); + // Must not exceed max endpoint number - TU_ASSERT( epnum < _ci_controller[rhport].ep_count ); + TU_ASSERT(epnum < ci_ep_count(dcd_reg)); //------------- Prepare Queue Head -------------// dcd_qhd_t * p_qhd = &_dcd_data.qhd[epnum][dir]; @@ -359,11 +398,9 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) p_qhd->qtd_overlay.next = QTD_NEXT_INVALID; - CleanInvalidateDCache_by_Addr((uint32_t*) &_dcd_data, sizeof(dcd_data_t)); + dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); // Enable EP Control - ci_hs_regs_t* dcd_reg = CI_HS_REG(rhport); - uint32_t const epctrl = (p_endpoint_desc->bmAttributes.xfer << ENDPTCTRL_TYPE_POS) | ENDPTCTRL_ENABLE | ENDPTCTRL_TOGGLE_RESET; if ( dir == TUSB_DIR_OUT ) @@ -382,7 +419,8 @@ void dcd_edpt_close_all (uint8_t rhport) ci_hs_regs_t* dcd_reg = CI_HS_REG(rhport); // Disable all non-control endpoints - for( uint8_t epnum=1; epnum < _ci_controller[rhport].ep_count; epnum++) + uint8_t const ep_count = ci_ep_count(dcd_reg); + for (uint8_t epnum = 1; epnum < ep_count; epnum++) { _dcd_data.qhd[epnum][TUSB_DIR_OUT].qtd_overlay.halted = 1; _dcd_data.qhd[epnum][TUSB_DIR_IN ].qtd_overlay.halted = 1; @@ -420,7 +458,7 @@ static void qhd_start_xfer(uint8_t rhport, uint8_t epnum, uint8_t dir) p_qhd->qtd_overlay.next = (uint32_t) p_qtd; // link qtd to qhd // flush cache - CleanInvalidateDCache_by_Addr((uint32_t*) &_dcd_data, sizeof(dcd_data_t)); + dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); if ( epnum == 0 ) { @@ -498,7 +536,7 @@ bool dcd_edpt_xfer_fifo (uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16 } } - CleanInvalidateDCache_by_Addr((uint32_t*) tu_align((uint32_t) fifo_info.ptr_wrap, 4), total_bytes - fifo_info.len_wrap + 31); + dcd_dcache_clean_invalidate((uint32_t*) tu_align((uint32_t) fifo_info.ptr_wrap, 4), total_bytes - fifo_info.len_wrap + 31); } else { @@ -611,7 +649,7 @@ void dcd_int_handler(uint8_t rhport) if (int_status & INTR_USB) { // Make sure we read the latest version of _dcd_data. - CleanInvalidateDCache_by_Addr((uint32_t*) &_dcd_data, sizeof(dcd_data_t)); + dcd_dcache_clean_invalidate(&_dcd_data, sizeof(dcd_data_t)); uint32_t const edpt_complete = dcd_reg->ENDPTCOMPLETE; dcd_reg->ENDPTCOMPLETE = edpt_complete; // acknowledge diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index ab6a42e11..8c27abbf6 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -42,28 +42,17 @@ #if CFG_TUSB_MCU == OPT_MCU_MIMXRT #include "ci_hs_imxrt.h" - // check if memory is cacheable i.e not in DTCM - TU_ATTR_ALWAYS_INLINE static inline bool is_cache_mem(uint32_t addr) { - return !(0x20000000 <= addr && addr < 0x20100000); - } - void hcd_dcache_clean(void* addr, uint32_t data_size) { - if (is_cache_mem((uint32_t) addr)) { - SCB_CleanDCache_by_Addr((uint32_t *) addr, (int32_t) data_size); - } + imxrt_dcache_clean(addr, data_size); } void hcd_dcache_invalidate(void* addr, uint32_t data_size) { - if (is_cache_mem((uint32_t) addr)) { - SCB_InvalidateDCache_by_Addr(addr, (int32_t) data_size); - } + imxrt_dcache_invalidate(addr, data_size); } -void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { - if (is_cache_mem((uint32_t) addr)) { - SCB_CleanInvalidateDCache_by_Addr(addr, (int32_t) data_size); + void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { + imxrt_dcache_clean_invalidate(addr, data_size); } -} #elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) #include "ci_hs_lpc18_43.h" @@ -75,8 +64,6 @@ void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { // MACRO CONSTANT TYPEDEF //--------------------------------------------------------------------+ -#define CI_HS_REG(_port) ((ci_hs_regs_t*) _ci_controller[_port].reg_base) - //--------------------------------------------------------------------+ // Controller API //--------------------------------------------------------------------+ diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 852e7f4fe..2b25eee9d 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -163,22 +163,15 @@ static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t static inline ehci_link_t* list_next (ehci_link_t const *p_link); TU_ATTR_WEAK void hcd_dcache_clean(void* addr, uint32_t data_size) { - (void) addr; - (void) data_size; + (void) addr; (void) data_size; } -// invalidate data cache: mark cache as invalid, next read will read from memory -// Required BOTH before and after an DMA RX transfer TU_ATTR_WEAK void hcd_dcache_invalidate(void* addr, uint32_t data_size) { - (void) addr; - (void) data_size; + (void) addr; (void) data_size; } -// clean and invalidate data cache -// Required before an DMA transfer where memory is both read/write by DMA TU_ATTR_WEAK void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { - (void) addr; - (void) data_size; + (void) addr; (void) data_size; } //--------------------------------------------------------------------+ diff --git a/src/tusb_option.h b/src/tusb_option.h index 4f3f3a985..948c9edf3 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -166,6 +166,10 @@ // WCH #define OPT_MCU_CH32V307 2200 ///< WCH CH32V307 + +// NXP LPC MCX +#define OPT_MCU_MCXN9 2300 ///< NXP MCX N9 Series + // Helper to check if configured MCU is one of listed // Apply _TU_CHECK_MCU with || as separator to list of input #define _TU_CHECK_MCU(_m) (CFG_TUSB_MCU == _m) @@ -274,7 +278,7 @@ // In case TUP_MCU_STRICT_ALIGN = 1 and TUP_ARCH_STRICT_ALIGN =0, we will not reply on compiler // to generate unaligned access code. // LPC_IP3511 Highspeed cannot access unaligned memory on USB_RAM -#if TUD_OPT_HIGH_SPEED && (CFG_TUSB_MCU == OPT_MCU_LPC54XXX || CFG_TUSB_MCU == OPT_MCU_LPC55XX) +#if TUD_OPT_HIGH_SPEED && TU_CHECK_MCU(OPT_MCU_LPC54XXX, OPT_MCU_LPC55XX) #define TUP_MCU_STRICT_ALIGN 1 #else #define TUP_MCU_STRICT_ALIGN 0 diff --git a/tools/cmake/cpu/cortex-m3.cmake b/tools/cmake/cpu/cortex-m3.cmake new file mode 100644 index 000000000..b740ee44c --- /dev/null +++ b/tools/cmake/cpu/cortex-m3.cmake @@ -0,0 +1,10 @@ +if (TOOLCHAIN STREQUAL "gcc") + list(APPEND TOOLCHAIN_COMMON_FLAGS + -mthumb + -mcpu=cortex-m3 + ) + + set(FREERTOS_PORT GCC_ARM_CM3 CACHE INTERNAL "") +else () + # TODO support IAR +endif () diff --git a/tools/cmake/cpu/cortex-m33.cmake b/tools/cmake/cpu/cortex-m33.cmake index fbd5027b1..26c91a64f 100644 --- a/tools/cmake/cpu/cortex-m33.cmake +++ b/tools/cmake/cpu/cortex-m33.cmake @@ -3,10 +3,11 @@ if (TOOLCHAIN STREQUAL "gcc") -mthumb -mcpu=cortex-m33 -mfloat-abi=hard - -mfpu=fpv5-d16 + #-mfpu=fpv5-d16 + -mfpu=fpv5-sp-d16 ) - set(FREERTOS_PORT GCC_ARM_CM33_NONSECURE CACHE INTERNAL "") + set(FREERTOS_PORT GCC_ARM_CM33_NTZ_NONSECURE CACHE INTERNAL "") else () # TODO support IAR endif () diff --git a/tools/cmake/toolchain/arm_gcc.cmake b/tools/cmake/toolchain/arm_gcc.cmake index c7b6cff98..5f25d637b 100644 --- a/tools/cmake/toolchain/arm_gcc.cmake +++ b/tools/cmake/toolchain/arm_gcc.cmake @@ -3,6 +3,8 @@ set(CMAKE_SYSTEM_NAME Generic) set(CMAKE_ASM_COMPILER "arm-none-eabi-gcc") set(CMAKE_C_COMPILER "arm-none-eabi-gcc") set(CMAKE_CXX_COMPILER "arm-none-eabi-g++") + +set(TOOLCHAIN_SIZE "arm-none-eabi-size" CACHE INTERNAL "") set(GCC_ELF2BIN "arm-none-eabi-objcopy") set_property(GLOBAL PROPERTY ELF2BIN ${GCC_ELF2BIN}) diff --git a/tools/get_deps.py b/tools/get_deps.py index be5738dc1..f499562cb 100644 --- a/tools/get_deps.py +++ b/tools/get_deps.py @@ -24,7 +24,7 @@ deps_optional = { 'hw/mcu/nordic/nrfx' : ['2527e3c8449cfd38aee41598e8af8492f410ed15', 'https://github.com/NordicSemiconductor/nrfx.git' ], 'hw/mcu/nuvoton' : ['2204191ec76283371419fbcec207da02e1bc22fa', 'https://github.com/majbthrd/nuc_driver.git' ], 'hw/mcu/nxp/lpcopen' : ['43c45c85405a5dd114fff0ea95cca62837740c13', 'https://github.com/hathach/nxp_lpcopen.git' ], - 'hw/mcu/nxp/mcux-sdk' : ['f357a1150f6cf6c6b844f53f2d426bfb3e649850', 'https://github.com/NXPmicro/mcux-sdk.git' ], + 'hw/mcu/nxp/mcux-sdk' : ['950819b7de9b32f92c3edf396bc5ffb8d66e7009', 'https://github.com/hathach/mcux-sdk.git' ], 'hw/mcu/nxp/nxp_sdk' : ['845c8fc49b6fb660f06a5c45225494eacb06f00c', 'https://github.com/hathach/nxp_sdk.git' ], 'hw/mcu/raspberry_pi/Pico-PIO-USB' : ['c3715ce94b6f6391856de56081d4d9b3e98fa93d', 'https://github.com/sekigon-gonnoc/Pico-PIO-USB.git' ], 'hw/mcu/renesas/fsp' : ['8dc14709f2a6518b43f71efad70d900b7718d9f1', 'https://github.com/renesas/fsp.git' ], diff --git a/tools/make/cpu/cortex-m33.mk b/tools/make/cpu/cortex-m33.mk index 2ea3a0753..3d12b01fd 100644 --- a/tools/make/cpu/cortex-m33.mk +++ b/tools/make/cpu/cortex-m33.mk @@ -3,7 +3,9 @@ ifeq ($(TOOLCHAIN),gcc) -mthumb \ -mcpu=cortex-m33 \ -mfloat-abi=hard \ - -mfpu=fpv5-d16 \ + -mfpu=fpv5-sp-d16 \ + + #-mfpu=fpv5-d16 \ #set(FREERTOS_PORT GCC_ARM_CM33_NONSECURE CACHE INTERNAL "") FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM33_NTZ/non_secure -- cgit v1.3.1 From 57d2eb603b412a6bfbfdad7fb0bac854302b4351 Mon Sep 17 00:00:00 2001 From: Aladdin Bakosh Date: Mon, 15 May 2023 18:27:45 +0200 Subject: fix(RA Host Portable): implement missing function __builtin_ctz(x) for IAR --- src/portable/renesas/rusb2/hcd_rusb2.c | 2 +- src/portable/renesas/rusb2/rusb2_ra.h | 4 ++++ 2 files changed, 5 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index e4743223e..0e6fa1618 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -407,7 +407,7 @@ static void process_pipe0_bemp(uint8_t rhport) static void process_pipe_nrdy(uint8_t rhport, unsigned num) { (void)rhport; - unsigned result; + xfer_result_t result; uint16_t volatile *ctr = get_pipectr(num); // TU_LOG1("NRDY %d %x\n", num, *ctr); switch (*ctr & RUSB2_PIPE_CTR_PID_Msk) { diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 5785850cc..5be9f11ce 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -36,6 +36,10 @@ extern "C" { #define RUSB2_REG_BASE (0x40090000) +#if defined(__ICCARM__) + #define __builtin_ctz(x) __iar_builtin_CLZ(__iar_builtin_RBIT(x)) +#endif + TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_enable(uint8_t rhport) { (void) rhport; -- cgit v1.3.1 From 268ab5863a3437c804d6db0ea5dc9f90560e9ffc Mon Sep 17 00:00:00 2001 From: Aladdin Bakosh Date: Wed, 24 May 2023 14:08:42 +0200 Subject: fix(RA Host Portable): git rid of the IAR warnings for packed --- src/portable/renesas/rusb2/rusb2_type.h | 146 ++++++++++++++++---------------- 1 file changed, 73 insertions(+), 73 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index 7a2898366..d80ecc62e 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -41,11 +41,11 @@ extern "C" { TU_ATTR_PACKED_BEGIN TU_ATTR_BIT_FIELD_ORDER_BEGIN -typedef struct TU_ATTR_PACKED { +typedef struct { union { volatile uint16_t E; /* (@ 0x00000000) Pipe Transaction Counter Enable Register */ - struct { + struct TU_ATTR_PACKED { uint16_t : 8; volatile uint16_t TRCLR : 1; /* [8..8] Transaction Counter Clear */ volatile uint16_t TRENB : 1; /* [9..9] Transaction Counter Enable */ @@ -56,18 +56,18 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t N; /* (@ 0x00000002) Pipe Transaction Counter Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t TRNCNT : 16; /* [15..0] Transaction Counter */ } N_b; }; } RUSB2_PIPE_TR_t; /* Size = 4 (0x4) */ /* LINK_REG Structure */ -typedef struct TU_ATTR_PACKED { +typedef struct { union { volatile uint16_t SYSCFG; /* (@ 0x00000000) System Configuration Control Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t USBE : 1; /* [0..0] USB Operation Enable */ uint16_t : 2; volatile uint16_t DMRPU : 1; /* [3..3] D- Line Resistor Control */ @@ -85,7 +85,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t BUSWAIT; /* (@ 0x00000002) CPU Bus Wait Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t BWAIT : 4; /* [3..0] CPU Bus Access Wait Specification BWAIT waits (BWAIT+2 access cycles) */ uint16_t : 12; } BUSWAIT_b; @@ -94,7 +94,7 @@ typedef struct TU_ATTR_PACKED { union { volatile const uint16_t SYSSTS0; /* (@ 0x00000004) System Configuration Status Register 0 */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t LNST : 2; /* [1..0] USB Data Line Status Monitor */ volatile const uint16_t IDMON : 1; /* [2..2] External ID0 Input Pin Monitor */ uint16_t : 2; @@ -109,7 +109,7 @@ typedef struct TU_ATTR_PACKED { union { volatile const uint16_t PLLSTA; /* (@ 0x00000006) PLL Status Register */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t PLLLOCK : 1; /* [0..0] PLL Lock Flag */ uint16_t : 15; } PLLSTA_b; @@ -118,7 +118,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t DVSTCTR0; /* (@ 0x00000008) Device State Control Register 0 */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t RHST : 3; /* [2..0] USB Bus Reset Status */ uint16_t : 1; volatile uint16_t UACT : 1; /* [4..4] USB Bus Enable */ @@ -137,7 +137,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t TESTMODE; /* (@ 0x0000000C) USB Test Mode Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t UTST : 4; /* [3..0] Test Mode */ uint16_t : 12; } TESTMODE_b; @@ -148,7 +148,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint32_t CFIFO; /* (@ 0x00000014) CFIFO Port Register */ - struct { + struct TU_ATTR_PACKED { union { volatile uint16_t CFIFOL; /* (@ 0x00000014) CFIFO Port Register L */ volatile uint8_t CFIFOLL; /* (@ 0x00000014) CFIFO Port Register LL */ @@ -157,7 +157,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t CFIFOH; /* (@ 0x00000016) CFIFO Port Register H */ - struct { + struct TU_ATTR_PACKED { volatile const uint8_t RESERVED3; volatile uint8_t CFIFOHH; /* (@ 0x00000017) CFIFO Port Register HH */ }; @@ -168,7 +168,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint32_t D0FIFO; /* (@ 0x00000018) D0FIFO Port Register */ - struct { + struct TU_ATTR_PACKED { union { volatile uint16_t D0FIFOL; /* (@ 0x00000018) D0FIFO Port Register L */ volatile uint8_t D0FIFOLL; /* (@ 0x00000018) D0FIFO Port Register LL */ @@ -177,7 +177,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t D0FIFOH; /* (@ 0x0000001A) D0FIFO Port Register H */ - struct { + struct TU_ATTR_PACKED { volatile const uint8_t RESERVED4; volatile uint8_t D0FIFOHH; /* (@ 0x0000001B) D0FIFO Port Register HH */ }; @@ -188,7 +188,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint32_t D1FIFO; /* (@ 0x0000001C) D1FIFO Port Register */ - struct { + struct TU_ATTR_PACKED { union { volatile uint16_t D1FIFOL; /* (@ 0x0000001C) D1FIFO Port Register L */ volatile uint8_t D1FIFOLL; /* (@ 0x0000001C) D1FIFO Port Register LL */ @@ -197,7 +197,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t D1FIFOH; /* (@ 0x0000001E) D1FIFO Port Register H */ - struct { + struct TU_ATTR_PACKED { volatile const uint8_t RESERVED5; volatile uint8_t D1FIFOHH; /* (@ 0x0000001F) D1FIFO Port Register HH */ }; @@ -208,7 +208,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t CFIFOSEL; /* (@ 0x00000020) CFIFO Port Select Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t CURPIPE : 4; /* [3..0] CFIFO Port Access Pipe Specification */ uint16_t : 1; volatile uint16_t ISEL : 1; /* [5..5] CFIFO Port Access Direction When DCP is Selected */ @@ -225,12 +225,12 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t CFIFOCTR; /* (@ 0x00000022) CFIFO Port Control Register */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t DTLN : 12; /* [11..0] Receive Data LengthIndicates the length of the receive data. */ uint16_t : 1; volatile const uint16_t FRDY : 1; /* [13..13] FIFO Port Ready */ - volatile uint16_t BCLR : 1; /* [14..14] CPU Buffer ClearNote: Only 0 can be read. */ - volatile uint16_t BVAL : 1; /* [15..15] Buffer Memory Valid Flag */ + volatile uint16_t BCLR : 1; /* [14..14] CPU Buffer ClearNote: Only 0 can be read. */ + volatile uint16_t BVAL : 1; /* [15..15] Buffer Memory Valid Flag */ } CFIFOCTR_b; }; volatile const uint32_t RESERVED6; @@ -238,7 +238,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t D0FIFOSEL; /* (@ 0x00000028) D0FIFO Port Select Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t CURPIPE : 4; /* [3..0] FIFO Port Access Pipe Specification */ uint16_t : 4; volatile uint16_t BIGEND : 1; /* [8..8] FIFO Port Endian Control */ @@ -254,19 +254,19 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t D0FIFOCTR; /* (@ 0x0000002A) D0FIFO Port Control Register */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t DTLN : 12; /* [11..0] Receive Data LengthIndicates the length of the receive data. */ uint16_t : 1; volatile const uint16_t FRDY : 1; /* [13..13] FIFO Port Ready */ - volatile uint16_t BCLR : 1; /* [14..14] CPU Buffer ClearNote: Only 0 can be read. */ - volatile uint16_t BVAL : 1; /* [15..15] Buffer Memory Valid Flag */ + volatile uint16_t BCLR : 1; /* [14..14] CPU Buffer ClearNote: Only 0 can be read. */ + volatile uint16_t BVAL : 1; /* [15..15] Buffer Memory Valid Flag */ } D0FIFOCTR_b; }; union { volatile uint16_t D1FIFOSEL; /* (@ 0x0000002C) D1FIFO Port Select Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t CURPIPE : 4; /* [3..0] FIFO Port Access Pipe Specification */ uint16_t : 4; volatile uint16_t BIGEND : 1; /* [8..8] FIFO Port Endian Control */ @@ -282,7 +282,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t D1FIFOCTR; /* (@ 0x0000002E) D1FIFO Port Control Register */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t DTLN : 12; /* [11..0] Receive Data LengthIndicates the length of the receive data. */ uint16_t : 1; volatile const uint16_t FRDY : 1; /* [13..13] FIFO Port Ready */ @@ -294,7 +294,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t INTENB0; /* (@ 0x00000030) Interrupt Enable Register 0 */ - struct { + struct TU_ATTR_PACKED { uint16_t : 8; volatile uint16_t BRDYE : 1; /* [8..8] Buffer Ready Interrupt Enable */ volatile uint16_t NRDYE : 1; /* [9..9] Buffer Not Ready Response Interrupt Enable */ @@ -310,7 +310,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t INTENB1; /* (@ 0x00000032) Interrupt Enable Register 1 */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PDDETINTE0 : 1; /* [0..0] PDDETINT0 Detection Interrupt Enable */ uint16_t : 3; volatile uint16_t SACKE : 1; /* [4..4] Setup Transaction Normal Response Interrupt Enable */ @@ -329,7 +329,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t BRDYENB; /* (@ 0x00000036) BRDY Interrupt Enable Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PIPE0BRDYE : 1; /* [0..0] BRDY Interrupt Enable for PIPE */ volatile uint16_t PIPE1BRDYE : 1; /* [1..1] BRDY Interrupt Enable for PIPE */ volatile uint16_t PIPE2BRDYE : 1; /* [2..2] BRDY Interrupt Enable for PIPE */ @@ -347,7 +347,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t NRDYENB; /* (@ 0x00000038) NRDY Interrupt Enable Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PIPE0NRDYE : 1; /* [0..0] NRDY Interrupt Enable for PIPE */ volatile uint16_t PIPE1NRDYE : 1; /* [1..1] NRDY Interrupt Enable for PIPE */ volatile uint16_t PIPE2NRDYE : 1; /* [2..2] NRDY Interrupt Enable for PIPE */ @@ -365,7 +365,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t BEMPENB; /* (@ 0x0000003A) BEMP Interrupt Enable Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PIPE0BEMPE : 1; /* [0..0] BEMP Interrupt Enable for PIPE */ volatile uint16_t PIPE1BEMPE : 1; /* [1..1] BEMP Interrupt Enable for PIPE */ volatile uint16_t PIPE2BEMPE : 1; /* [2..2] BEMP Interrupt Enable for PIPE */ @@ -383,7 +383,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t SOFCFG; /* (@ 0x0000003C) SOF Output Configuration Register */ - struct { + struct TU_ATTR_PACKED { uint16_t : 4; volatile const uint16_t EDGESTS : 1; /* [4..4] Edge Interrupt Output Status Monitor */ volatile uint16_t INTL : 1; /* [5..5] Interrupt Output Sense Select */ @@ -397,7 +397,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t PHYSET; /* (@ 0x0000003E) PHY Setting Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t DIRPD : 1; /* [0..0] Power-Down Control */ volatile uint16_t PLLRESET : 1; /* [1..1] PLL Reset Control */ uint16_t : 1; @@ -415,7 +415,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t INTSTS0; /* (@ 0x00000040) Interrupt Status Register 0 */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t CTSQ : 3; /* [2..0] Control Transfer Stage */ volatile uint16_t VALID : 1; /* [3..3] USB Request Reception */ volatile const uint16_t DVSQ : 3; /* [6..4] Device State */ @@ -434,7 +434,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t INTSTS1; /* (@ 0x00000042) Interrupt Status Register 1 */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PDDETINT0 : 1; /* [0..0] PDDET0 Detection Interrupt Status */ uint16_t : 3; volatile uint16_t SACK : 1; /* [4..4] Setup Transaction Normal Response Interrupt Status */ @@ -456,7 +456,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t BRDYSTS; /* (@ 0x00000046) BRDY Interrupt Status Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PIPE0BRDY : 1; /* [0..0] BRDY Interrupt Status for PIPE */ volatile uint16_t PIPE1BRDY : 1; /* [1..1] BRDY Interrupt Status for PIPE */ volatile uint16_t PIPE2BRDY : 1; /* [2..2] BRDY Interrupt Status for PIPE */ @@ -474,7 +474,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t NRDYSTS; /* (@ 0x00000048) NRDY Interrupt Status Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PIPE0NRDY : 1; /* [0..0] NRDY Interrupt Status for PIPE */ volatile uint16_t PIPE1NRDY : 1; /* [1..1] NRDY Interrupt Status for PIPE */ volatile uint16_t PIPE2NRDY : 1; /* [2..2] NRDY Interrupt Status for PIPE */ @@ -492,7 +492,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t BEMPSTS; /* (@ 0x0000004A) BEMP Interrupt Status Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PIPE0BEMP : 1; /* [0..0] BEMP Interrupt Status for PIPE */ volatile uint16_t PIPE1BEMP : 1; /* [1..1] BEMP Interrupt Status for PIPE */ volatile uint16_t PIPE2BEMP : 1; /* [2..2] BEMP Interrupt Status for PIPE */ @@ -510,7 +510,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t FRMNUM; /* (@ 0x0000004C) Frame Number Register */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t FRNM : 11; /* [10..0] Frame NumberLatest frame number */ uint16_t : 3; volatile uint16_t CRCE : 1; /* [14..14] Receive Data Error */ @@ -521,7 +521,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t UFRMNUM; /* (@ 0x0000004E) uFrame Number Register */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t UFRNM : 3; /* [2..0] MicroframeIndicate the microframe number. */ uint16_t : 12; volatile uint16_t DVCHG : 1; /* [15..15] Device State Change */ @@ -531,7 +531,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t USBADDR; /* (@ 0x00000050) USB Address Register */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t USBADDR : 7; /* [6..0] USB Address In device controller mode */ uint16_t : 1; volatile uint16_t STSRECOV0 : 3; /* [10..8] Status Recovery */ @@ -543,7 +543,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t USBREQ; /* (@ 0x00000054) USB Request Type Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t BMREQUESTTYPE : 8; /* [7..0] Request TypeThese bits store the USB request bmRequestType value. */ volatile uint16_t BREQUEST : 8; /* [15..8] RequestThese bits store the USB request bRequest value. */ } USBREQ_b; @@ -552,7 +552,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t USBVAL; /* (@ 0x00000056) USB Request Value Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t WVALUE : 16; /* [15..0] ValueThese bits store the USB request Value value. */ } USBVAL_b; }; @@ -560,7 +560,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t USBINDX; /* (@ 0x00000058) USB Request Index Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t WINDEX : 16; /* [15..0] IndexThese bits store the USB request wIndex value. */ } USBINDX_b; }; @@ -568,7 +568,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t USBLENG; /* (@ 0x0000005A) USB Request Length Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t WLENGTH : 16; /* [15..0] LengthThese bits store the USB request wLength value. */ } USBLENG_b; }; @@ -576,7 +576,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t DCPCFG; /* (@ 0x0000005C) DCP Configuration Register */ - struct { + struct TU_ATTR_PACKED { uint16_t : 4; volatile uint16_t DIR : 1; /* [4..4] Transfer Direction */ uint16_t : 2; @@ -589,7 +589,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t DCPMAXP; /* (@ 0x0000005E) DCP Maximum Packet Size Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t MXPS : 7; /* [6..0] Maximum Packet Size */ uint16_t : 5; volatile uint16_t DEVSEL : 4; /* [15..12] Device Select */ @@ -599,7 +599,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t DCPCTR; /* (@ 0x00000060) DCP Control Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PID : 2; /* [1..0] Response PID */ volatile uint16_t CCPL : 1; /* [2..2] Control Transfer End Enable */ uint16_t : 2; @@ -619,7 +619,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t PIPESEL; /* (@ 0x00000064) Pipe Window Select Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PIPESEL : 4; /* [3..0] Pipe Window Select */ uint16_t : 12; } PIPESEL_b; @@ -629,7 +629,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t PIPECFG; /* (@ 0x00000068) Pipe Configuration Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t EPNUM : 4; /* [3..0] Endpoint Number */ volatile uint16_t DIR : 1; /* [4..4] Transfer Direction */ uint16_t : 2; @@ -646,7 +646,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t PIPEMAXP; /* (@ 0x0000006C) Pipe Maximum Packet Size Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t MXPS : 9; /* [8..0] Maximum Packet Size */ uint16_t : 3; volatile uint16_t DEVSEL : 4; /* [15..12] Device Select */ @@ -656,7 +656,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t PIPEPERI; /* (@ 0x0000006E) Pipe Cycle Control Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t IITV : 3; /* [2..0] Interval Error Detection Interval */ uint16_t : 9; volatile uint16_t IFIS : 1; /* [12..12] Isochronous IN Buffer Flush */ @@ -667,7 +667,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t PIPE_CTR[9]; /* (@ 0x00000070) Pipe [0..8] Control Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t PID : 2; /* [1..0] Response PID */ uint16_t : 3; volatile const uint16_t PBUSY : 1; /* [5..5] Pipe Busy */ @@ -691,7 +691,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t USBBCCTRL0; /* (@ 0x000000B0) BC Control Register 0 */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t RPDME0 : 1; /* [0..0] D- Pin Pull-Down Control */ volatile uint16_t IDPSRCE0 : 1; /* [1..1] D+ Pin IDPSRC Output Control */ volatile uint16_t @@ -713,7 +713,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t UCKSEL; /* (@ 0x000000C4) USB Clock Selection Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t UCKSELC : 1; /* [0..0] USB Clock Selection */ uint16_t : 15; } UCKSEL_b; @@ -724,7 +724,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t USBMC; /* (@ 0x000000CC) USB Module Control Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t VDDUSBE : 1; /* [0..0] USB Reference Power Supply Circuit On/Off Control */ uint16_t : 6; volatile uint16_t VDCEN : 1; /* [7..7] USB Regulator On/Off Control */ @@ -736,7 +736,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t DEVADD[10]; /* (@ 0x000000D0) Device Address Configuration Register */ - struct { + struct TU_ATTR_PACKED { uint16_t : 6; volatile uint16_t USBSPD : 2; /* [7..6] Transfer Speed of Communication Target Device */ volatile uint16_t HUBPORT : 3; /* [10..8] Communication Target Connecting Hub Port */ @@ -749,7 +749,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint32_t PHYSLEW; /* (@ 0x000000F0) PHY Cross Point Adjustment Register */ - struct { + struct TU_ATTR_PACKED { volatile uint32_t SLEWR00 : 1; /* [0..0] Receiver Cross Point Adjustment 00 */ volatile uint32_t SLEWR01 : 1; /* [1..1] Receiver Cross Point Adjustment 01 */ volatile uint32_t SLEWF00 : 1; /* [2..2] Receiver Cross Point Adjustment 00 */ @@ -762,7 +762,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t LPCTRL; /* (@ 0x00000100) Low Power Control Register */ - struct { + struct TU_ATTR_PACKED { uint16_t : 7; volatile uint16_t HWUPM : 1; /* [7..7] Resume Return Mode Setting */ uint16_t : 8; @@ -772,7 +772,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t LPSTS; /* (@ 0x00000102) Low Power Status Register */ - struct { + struct TU_ATTR_PACKED { uint16_t : 14; volatile uint16_t SUSPENDM : 1; /* [14..14] UTMI SuspendM Control */ uint16_t : 1; @@ -783,7 +783,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t BCCTRL; /* (@ 0x00000140) Battery Charging Control Register */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t IDPSRCE : 1; /* [0..0] IDPSRC Control */ volatile uint16_t IDMSINKE : 1; /* [1..1] IDMSINK Control */ volatile uint16_t VDPSRCE : 1; /* [2..2] VDPSRC Control */ @@ -801,7 +801,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t PL1CTRL1; /* (@ 0x00000144) Function L1 Control Register 1 */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t L1RESPEN : 1; /* [0..0] L1 Response Enable */ volatile uint16_t L1RESPMD : 2; /* [2..1] L1 Response Mode */ volatile uint16_t L1NEGOMD : 1; /* [3..3] L1 Response Negotiation Control. */ @@ -816,7 +816,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t PL1CTRL2; /* (@ 0x00000146) Function L1 Control Register 2 */ - struct { + struct TU_ATTR_PACKED { uint16_t : 8; volatile uint16_t HIRDMON : 4; /* [11..8] HIRD Value Monitor */ volatile uint16_t RWEMON : 1; /* [12..12] RWE Value Monitor */ @@ -827,8 +827,8 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t HL1CTRL1; /* (@ 0x00000148) Host L1 Control Register 1 */ - struct { - volatile uint16_t L1REQ : 1; /* [0..0] L1 Transition Request */ + struct TU_ATTR_PACKED { + volatile uint16_t L1REQ : 1; /* [0..0] L1 Transition Request */ volatile const uint16_t L1STATUS : 2; /* [2..1] L1 Request Completion Status */ uint16_t : 13; } HL1CTRL1_b; @@ -837,7 +837,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t HL1CTRL2; /* (@ 0x0000014A) Host L1 Control Register 2 */ - struct { + struct TU_ATTR_PACKED { volatile uint16_t L1ADDR : 4; /* [3..0] LPM Token DeviceAddress */ uint16_t : 4; volatile uint16_t HIRD : 4; /* [11..8] LPM Token HIRD */ @@ -851,7 +851,7 @@ typedef struct TU_ATTR_PACKED { union { volatile const uint32_t DPUSR0R; /* (@ 0x00000160) Deep Standby USB Transceiver Control/Pin Monitor Register */ - struct { + struct TU_ATTR_PACKED { uint32_t : 20; volatile const uint32_t DOVCAHM : 1; /* [20..20] OVRCURA InputIndicates OVRCURA input signal on the HS side of USB port. */ volatile const uint32_t DOVCBHM : 1; /* [21..21] OVRCURB InputIndicates OVRCURB input signal on the HS side of USB port. */ @@ -864,7 +864,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint32_t DPUSR1R; /* (@ 0x00000164) Deep Standby USB Suspend/Resume Interrupt Register */ - struct { + struct TU_ATTR_PACKED { uint32_t : 4; volatile uint32_t DOVCAHE : 1; /* [4..4] OVRCURA Interrupt Enable Clear */ volatile uint32_t DOVCBHE : 1; /* [5..5] OVRCURB Interrupt Enable Clear */ @@ -882,7 +882,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t DPUSR2R; /* (@ 0x00000168) Deep Standby USB Suspend/Resume Interrupt Register */ - struct { + struct TU_ATTR_PACKED { volatile const uint16_t DPINT : 1; /* [0..0] Indication of Return from DP Interrupt Source */ volatile const uint16_t DMINT : 1; /* [1..1] Indication of Return from DM Interrupt Source */ uint16_t : 2; @@ -898,8 +898,8 @@ typedef struct TU_ATTR_PACKED { union { volatile uint16_t DPUSRCR; /* (@ 0x0000016A) Deep Standby USB Suspend/Resume Command Register */ - struct { - volatile uint16_t FIXPHY : 1; /* [0..0] USB Transceiver Control Fix */ + struct TU_ATTR_PACKED { + volatile uint16_t FIXPHY : 1; /* [0..0] USB Transceiver Control Fix */ volatile uint16_t FIXPHYPD : 1; /* [1..1] USB Transceiver Control Fix for PLL */ uint16_t : 14; } DPUSRCR_b; @@ -910,7 +910,7 @@ typedef struct TU_ATTR_PACKED { volatile uint32_t DPUSR0R_FS; /* (@ 0x00000400) Deep Software Standby USB Transceiver Control/Pin Monitor Register */ - struct { + struct TU_ATTR_PACKED { volatile uint32_t SRPC0 : 1; /* [0..0] USB Single End Receiver Control */ volatile uint32_t RPUE0 : 1; /* [1..1] DP Pull-Up Resistor Control */ uint32_t : 1; @@ -931,7 +931,7 @@ typedef struct TU_ATTR_PACKED { union { volatile uint32_t DPUSR1R_FS; /* (@ 0x00000404) Deep Software Standby USB Suspend/Resume Interrupt Register */ - struct { + struct TU_ATTR_PACKED { volatile uint32_t DPINTE0 : 1; /* [0..0] USB DP Interrupt Enable/Clear */ volatile uint32_t DMINTE0 : 1; /* [1..1] USB DM Interrupt Enable/Clear */ uint32_t : 2; -- cgit v1.3.1 From cdae66c8371e1c73d28279462fa8598a9daae5a7 Mon Sep 17 00:00:00 2001 From: Martino Facchin Date: Mon, 5 Jun 2023 09:04:52 +0200 Subject: renesas_rx: fix compilation on latest GCC __CCRX__ only applyes to version 4 of RX family compiler http://tool-support.renesas.com/autoupdate/support/onlinehelp/csp/V4.01.00/CS+.chm/Compiler-CCRX.chm/Output/ccrx04c0201y.html __RX__ is one of the macros exported by latest gcc (gcc_8.3.0.202305_rx_elf) --- src/portable/renesas/rusb2/dcd_rusb2.c | 2 ++ src/portable/renesas/rusb2/hcd_rusb2.c | 2 ++ 2 files changed, 4 insertions(+) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 2653d0da6..e9ac46517 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -67,6 +67,8 @@ /* LINK core registers */ #if defined(__CCRX__) #define RUSB2 ((RUSB2_REG_t __evenaccess*) RUSB2_REG_BASE) +#elif defined(__RX__) + #define RUSB2 ((RUSB2_REG_t*) RUSB2_REG_BASE) #elif (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) #define RUSB2 ((R_USB_HS0_Type*)R_USB_HS0_BASE) #else diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 1e26c931d..b97ffd7e9 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -54,6 +54,8 @@ /* LINK core registers */ #if defined(__CCRX__) #define RUSB2 ((RUSB2_REG_t __evenaccess*) RUSB2_REG_BASE) +#elif defined(__RX__) + #define RUSB2 ((RUSB2_REG_t*) RUSB2_REG_BASE) #elif (CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST) #define RUSB2 ((R_USB_HS0_Type*) R_USB_HS0_BASE) #else -- cgit v1.3.1 From 2b735ee8f5476168d6b5ed1dc32edc52f4d3648a Mon Sep 17 00:00:00 2001 From: Martino Facchin Date: Mon, 5 Jun 2023 09:31:58 +0200 Subject: renesas_ra: fix wrong ifdef Since CFG_TUSB_RHPORT1_MODE is always defined now for backwards compatibility --- src/portable/renesas/rusb2/rusb2_ra.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/rusb2_ra.c b/src/portable/renesas/rusb2/rusb2_ra.c index 2b6ce7b2f..ff2191b1f 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.c +++ b/src/portable/renesas/rusb2/rusb2_ra.c @@ -1,16 +1,16 @@ #include "tusb_option.h" #include "rusb2_ra.h" -#ifdef CFG_TUSB_RHPORT0_MODE +#if (CFG_TUSB_RHPORT0_MODE != 0) IRQn_Type _usb_fs_irqn = USBFS_INT_IRQn; void tud_set_irq_usbfs(IRQn_Type q) { _usb_fs_irqn = q; } #endif -#ifdef CFG_TUSB_RHPORT1_MODE +#if (CFG_TUSB_RHPORT1_MODE != 0) IRQn_Type _usb_hs_irqn = USBHS_USB_INT_RESUME_IRQn; void tud_set_irq_usbhs(IRQn_Type q) { _usb_hs_irqn = q; } -#endif \ No newline at end of file +#endif -- cgit v1.3.1 From b893f1d5417adf8cf874d6b2e7946582ca37982a Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 7 Jun 2023 15:10:40 +0700 Subject: inital support for usb typec and pd example --- examples/typec/power_delivery/CMakeLists.txt | 32 +++++ examples/typec/power_delivery/Makefile | 11 ++ examples/typec/power_delivery/only.txt | 1 + examples/typec/power_delivery/src/main.c | 90 ++++++++++++ examples/typec/power_delivery/src/tusb_config.h | 79 +++++++++++ hw/bsp/stm32g4/boards/b_g474e_dpow1/board.h | 8 +- hw/bsp/stm32g4/family.c | 133 +---------------- hw/bsp/stm32g4/family.cmake | 1 + src/CMakeLists.txt | 2 + src/common/tusb_mcu.h | 2 + src/common/tusb_types.h | 91 ++++++++++-- src/portable/st/typec/typec_stm32.c | 181 ++++++++++++++++++++++++ src/tusb.h | 5 + src/typec/tcd.h | 58 ++++++++ src/typec/utcd.c | 48 +++++++ src/typec/utcd.h | 54 +++++++ 16 files changed, 651 insertions(+), 145 deletions(-) create mode 100644 examples/typec/power_delivery/CMakeLists.txt create mode 100644 examples/typec/power_delivery/Makefile create mode 100644 examples/typec/power_delivery/only.txt create mode 100644 examples/typec/power_delivery/src/main.c create mode 100644 examples/typec/power_delivery/src/tusb_config.h create mode 100644 src/portable/st/typec/typec_stm32.c create mode 100644 src/typec/tcd.h create mode 100644 src/typec/utcd.c create mode 100644 src/typec/utcd.h (limited to 'src/portable') diff --git a/examples/typec/power_delivery/CMakeLists.txt b/examples/typec/power_delivery/CMakeLists.txt new file mode 100644 index 000000000..4ab8d5a65 --- /dev/null +++ b/examples/typec/power_delivery/CMakeLists.txt @@ -0,0 +1,32 @@ +cmake_minimum_required(VERSION 3.17) + +include(${CMAKE_CURRENT_SOURCE_DIR}/../../../hw/bsp/family_support.cmake) + +# gets PROJECT name for the example (e.g. -) +family_get_project_name(PROJECT ${CMAKE_CURRENT_LIST_DIR}) + +project(${PROJECT} C CXX ASM) + +# Checks this example is valid for the family and initializes the project +family_initialize_project(${PROJECT} ${CMAKE_CURRENT_LIST_DIR}) + +# Espressif has its own cmake build system +if(FAMILY STREQUAL "espressif") + return() +endif() + +add_executable(${PROJECT}) + +# Example source +target_sources(${PROJECT} PUBLIC + ${CMAKE_CURRENT_SOURCE_DIR}/src/main.c + ) + +# Example include +target_include_directories(${PROJECT} PUBLIC + ${CMAKE_CURRENT_SOURCE_DIR}/src + ) + +# Configure compilation flags and libraries for the example... see the corresponding function +# in hw/bsp/FAMILY/family.cmake for details. +family_configure_device_example(${PROJECT}) diff --git a/examples/typec/power_delivery/Makefile b/examples/typec/power_delivery/Makefile new file mode 100644 index 000000000..2a3d854fb --- /dev/null +++ b/examples/typec/power_delivery/Makefile @@ -0,0 +1,11 @@ +include ../../make.mk + +INC += \ + src \ + $(TOP)/hw \ + +# Example source +EXAMPLE_SOURCE += $(wildcard src/*.c) +SRC_C += $(addprefix $(CURRENT_PATH)/, $(EXAMPLE_SOURCE)) + +include ../../rules.mk diff --git a/examples/typec/power_delivery/only.txt b/examples/typec/power_delivery/only.txt new file mode 100644 index 000000000..657aeaac5 --- /dev/null +++ b/examples/typec/power_delivery/only.txt @@ -0,0 +1 @@ +mcu:STM32G4 diff --git a/examples/typec/power_delivery/src/main.c b/examples/typec/power_delivery/src/main.c new file mode 100644 index 000000000..9d032b6bb --- /dev/null +++ b/examples/typec/power_delivery/src/main.c @@ -0,0 +1,90 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + */ + +#include +#include +#include + +#include "bsp/board.h" +#include "tusb.h" + +//--------------------------------------------------------------------+ +// MACRO CONSTANT TYPEDEF PROTOTYPES +//--------------------------------------------------------------------+ + +/* Blink pattern + * - 250 ms : button is not pressed + * - 1000 ms : button is pressed (and hold) + */ +enum { + BLINK_PRESSED = 250, + BLINK_UNPRESSED = 1000 +}; + +static uint32_t blink_interval_ms = BLINK_UNPRESSED; + +void led_blinking_task(void); + +#define HELLO_STR "Hello from TinyUSB\r\n" + +int main(void) +{ + board_init(); + board_led_write(true); + + tuc_init(0, TYPEC_PORT_SNK); + + uint32_t start_ms = 0; + bool led_state = false; + + while (1) { + led_blinking_task(); + +// tuc_task(); + } +} + +#if CFG_TUSB_MCU == OPT_MCU_ESP32S2 || CFG_TUSB_MCU == OPT_MCU_ESP32S3 +void app_main(void) +{ + main(); +} +#endif + +//--------------------------------------------------------------------+ +// BLINKING TASK +//--------------------------------------------------------------------+ +void led_blinking_task(void) +{ + static uint32_t start_ms = 0; + static bool led_state = false; + + // Blink every interval ms + if ( board_millis() - start_ms < blink_interval_ms) return; // not enough time + start_ms += blink_interval_ms; + + board_led_write(led_state); + led_state = 1 - led_state; // toggle +} diff --git a/examples/typec/power_delivery/src/tusb_config.h b/examples/typec/power_delivery/src/tusb_config.h new file mode 100644 index 000000000..deddcbfa4 --- /dev/null +++ b/examples/typec/power_delivery/src/tusb_config.h @@ -0,0 +1,79 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + */ + +#ifndef _TUSB_CONFIG_H_ +#define _TUSB_CONFIG_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +// special example that doesn't enable device or host stack +// This can cause some TinyUSB API missing, this define hack to allow us to fill those API +// to pass the compilation process +#define tud_int_handler(x) + +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU + #error CFG_TUSB_MCU must be defined +#endif + +#ifndef CFG_TUSB_OS + #define CFG_TUSB_OS OPT_OS_NONE +#endif + +#define CFG_TUD_ENABLED 0 +#define CFG_TUH_ENABLED 0 + +// Enable TYPEC stack +#define CFG_TUC_ENABLED 1 + +// CFG_TUSB_DEBUG is defined by compiler in DEBUG build +// #define CFG_TUSB_DEBUG 0 + +/* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. + * Tinyusb use follows macros to declare transferring memory so that they can be put + * into those specific section. + * e.g + * - CFG_TUSB_MEM SECTION : __attribute__ (( section(".usb_ram") )) + * - CFG_TUSB_MEM_ALIGN : __attribute__ ((aligned(4))) + */ +#ifndef CFG_TUSB_MEM_SECTION +#define CFG_TUSB_MEM_SECTION +#endif + +#ifndef CFG_TUSB_MEM_ALIGN +#define CFG_TUSB_MEM_ALIGN __attribute__ ((aligned(4))) +#endif + +#ifdef __cplusplus + } +#endif + +#endif /* _TUSB_CONFIG_H_ */ diff --git a/hw/bsp/stm32g4/boards/b_g474e_dpow1/board.h b/hw/bsp/stm32g4/boards/b_g474e_dpow1/board.h index 6b00efc8f..e61b13170 100644 --- a/hw/bsp/stm32g4/boards/b_g474e_dpow1/board.h +++ b/hw/bsp/stm32g4/boards/b_g474e_dpow1/board.h @@ -58,7 +58,7 @@ // RCC Clock //--------------------------------------------------------------------+ -// CPU Frequency (Core Clock) is 150MHz +// CPU Frequency (Core Clock) is 170 MHz static inline void board_clock_init(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; @@ -74,9 +74,9 @@ static inline void board_clock_init(void) RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI; RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV4; - RCC_OscInitStruct.PLL.PLLN = 75; - RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; - RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV4; + RCC_OscInitStruct.PLL.PLLN = 85; + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV10; + RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV2; RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV2; HAL_RCC_OscConfig(&RCC_OscInitStruct); diff --git a/hw/bsp/stm32g4/family.c b/hw/bsp/stm32g4/family.c index 6c870ac7a..d0601b385 100644 --- a/hw/bsp/stm32g4/family.c +++ b/hw/bsp/stm32g4/family.c @@ -30,132 +30,6 @@ #include "bsp/board.h" #include "board.h" - -//--------------------------------------------------------------------+ -// USB PD -//--------------------------------------------------------------------+ - -void usbpd_init(uint8_t port_num, tusb_typec_port_type_t port_type) { - (void) port_num; - - // Initialization phase: CFG1 - UCPD1->CFG1 = (0x0d << UCPD_CFG1_HBITCLKDIV_Pos) | (0x10 << UCPD_CFG1_IFRGAP_Pos) | (0x07 << UCPD_CFG1_TRANSWIN_Pos) | - (0x01 << UCPD_CFG1_PSC_UCPDCLK_Pos) | (0x1f << UCPD_CFG1_RXORDSETEN_Pos) | - ( 0 << UCPD_CFG1_TXDMAEN_Pos) | (0 << UCPD_CFG1_RXDMAEN_Pos); - UCPD1->CFG1 |= UCPD_CFG1_UCPDEN; - - // General programming sequence (with UCPD configured then enabled) - if (port_type == TUSB_TYPEC_PORT_SNK) { - // Enable both CC Phy - UCPD1->CR = (0x01 << UCPD_CR_ANAMODE_Pos) | (0x03 << UCPD_CR_CCENABLE_Pos); - - // Read Voltage State on CC1 & CC2 fore initial state - uint32_t vstate_cc[2]; - vstate_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; - vstate_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; - - TU_LOG1_INT(vstate_cc[0]); - TU_LOG1_INT(vstate_cc[1]); - - // Enable CC1 & CC2 Interrupt - UCPD1->IMR = UCPD_IMR_TYPECEVT1IE | UCPD_IMR_TYPECEVT2IE; - } - - // Enable interrupt - NVIC_EnableIRQ(UCPD1_IRQn); -} - -uint8_t pd_rx_buf[262]; -uint32_t pd_rx_count = 0; - -void UCPD1_IRQHandler(void) { - uint32_t sr = UCPD1->SR; - sr &= UCPD1->IMR; - -// TU_LOG1("UCPD1_IRQHandler: sr = 0x%08X\n", sr); - - if (sr & (UCPD_SR_TYPECEVT1 | UCPD_SR_TYPECEVT2)) { - uint32_t vstate_cc[2]; - vstate_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; - vstate_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; - - TU_LOG1("VState CC1 = %u, CC2 = %u\n", vstate_cc[0], vstate_cc[1]); - - uint32_t cr = UCPD1->CR; - - // TODO only support SNK for now, required highest voltage for now - if ((sr & UCPD_SR_TYPECEVT1) && (vstate_cc[0] == 3)) { - TU_LOG1("Attach CC1\n"); - cr &= ~UCPD_CR_PHYCCSEL; - cr |= UCPD_CR_PHYRXEN; - } else if ((sr & UCPD_SR_TYPECEVT2) && (vstate_cc[1] == 3)) { - TU_LOG1("Attach CC2\n"); - cr |= UCPD_CR_PHYCCSEL; - cr |= UCPD_CR_PHYRXEN; - } else { - TU_LOG1("Detach\n"); - cr &= ~UCPD_CR_PHYRXEN; - } - - if (cr & UCPD_CR_PHYRXEN) { - // Enable Interrupt - UCPD1->IMR |= UCPD_IMR_TXMSGDISCIE | UCPD_IMR_TXMSGSENTIE | UCPD_IMR_TXMSGABTIE | UCPD_IMR_TXUNDIE | - UCPD_IMR_RXNEIE | UCPD_IMR_RXORDDETIE | UCPD_IMR_RXHRSTDETIE | UCPD_IMR_RXOVRIE | - UCPD_IMR_RXMSGENDIE | UCPD_IMR_HRSTDISCIE | UCPD_IMR_HRSTSENTIE; - } - - // Enable PD RX - UCPD1->CR = cr; - - // ack - UCPD1->ICR = UCPD_ICR_TYPECEVT1CF | UCPD_ICR_TYPECEVT2CF; - } - - //------------- Receive -------------// - if (sr & UCPD_SR_RXORDDET) { - // SOP: Start of Packet. - // uint8_t order_set = UCPD1->RX_ORDSET & UCPD_RX_ORDSET_RXORDSET_Msk; - - // reset count when received SOP - pd_rx_count = 0; - - // ack - UCPD1->ICR = UCPD_ICR_RXORDDETCF; - } - - if (sr & UCPD_SR_RXNE) { - // TODO DMA later - do { - pd_rx_buf[pd_rx_count++] = UCPD1->RXDR; - } while (UCPD1->SR & UCPD_SR_RXNE); - } - - if (sr & UCPD_SR_RXMSGEND) { - // End of message - uint32_t payload_size = UCPD1->RX_PAYSZ; - - // ack - UCPD1->ICR = UCPD_ICR_RXMSGENDCF; - } - - if (sr & UCPD_SR_RXOVR) { - TU_LOG1("RXOVR\n"); - TU_LOG1_HEX(pd_rx_count); - // ack - UCPD1->ICR = UCPD_ICR_RXOVRCF; - } - -// if (sr & UCPD_SR_RXNE) { -// uint8_t data = UCPD1->RXDR; -// pd_rx_buf[pd_rx_count++] = data; -// TU_LOG1_HEX(data); -// } - -// else { -// TU_LOG_LOCATION(); -// } -} - //--------------------------------------------------------------------+ // Forward USB interrupt events to TinyUSB IRQ Handler //--------------------------------------------------------------------+ @@ -174,6 +48,11 @@ void USBWakeUp_IRQHandler(void) tud_int_handler(0); } +// USB PD +void UCPD1_IRQHandler(void) { + tuc_int_handler(0); +} + //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM //--------------------------------------------------------------------+ @@ -274,8 +153,6 @@ void board_init(void) // Default CC1/CC2 is PB4/PB6 // PB4 ------> UCPD1_CC2 // PB6 ------> UCPD1_CC1 - - usbpd_init(0, TUSB_TYPEC_PORT_SNK); #endif } diff --git a/hw/bsp/stm32g4/family.cmake b/hw/bsp/stm32g4/family.cmake index 2c10a9769..618563f66 100644 --- a/hw/bsp/stm32g4/family.cmake +++ b/hw/bsp/stm32g4/family.cmake @@ -90,6 +90,7 @@ function(family_configure_example TARGET) target_sources(${TARGET} PUBLIC # TinyUSB Port ${TOP}/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c + ${TOP}/src/portable/st/typec/typec_stm32.c # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c diff --git a/src/CMakeLists.txt b/src/CMakeLists.txt index 3dbd72d61..ce4486ecd 100644 --- a/src/CMakeLists.txt +++ b/src/CMakeLists.txt @@ -32,6 +32,8 @@ function(add_tinyusb TARGET) ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/class/hid/hid_host.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/class/msc/msc_host.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/class/vendor/vendor_host.c + # typec + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/typec/utcd.c ) target_include_directories(${TARGET} PUBLIC ${CMAKE_CURRENT_FUNCTION_LIST_DIR} diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 48f765674..bb4483f7d 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -199,6 +199,8 @@ #elif TU_CHECK_MCU(OPT_MCU_STM32G4) #define TUP_USBIP_FSDEV #define TUP_USBIP_FSDEV_STM32 + #define TUP_USBIP_TYPEC_STM32 + #define TUP_DCD_ENDPOINT_MAX 8 #elif TU_CHECK_MCU(OPT_MCU_STM32G0) diff --git a/src/common/tusb_types.h b/src/common/tusb_types.h index 7b82c51d9..e6b350a40 100644 --- a/src/common/tusb_types.h +++ b/src/common/tusb_types.h @@ -232,16 +232,6 @@ enum { #define TUSB_DESC_CONFIG_POWER_MA(x) ((x)/2) -//--------------------------------------------------------------------+ -// TYPE-C -//--------------------------------------------------------------------+ - -typedef enum { - TUSB_TYPEC_PORT_SRC, - TUSB_TYPEC_PORT_SNK, - TUSB_TYPEC_PORT_DRP -} tusb_typec_port_type_t; - //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ @@ -487,9 +477,9 @@ typedef struct TU_ATTR_PACKED uint16_t bcdDFUVersion; } tusb_desc_dfu_functional_t; -/*------------------------------------------------------------------*/ -/* Types - *------------------------------------------------------------------*/ +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ typedef struct TU_ATTR_PACKED{ union { struct TU_ATTR_PACKED { @@ -509,6 +499,81 @@ typedef struct TU_ATTR_PACKED{ TU_VERIFY_STATIC( sizeof(tusb_control_request_t) == 8, "size is not correct"); +//--------------------------------------------------------------------+ +// TYPE-C +//--------------------------------------------------------------------+ + +typedef enum { + TYPEC_PORT_SRC, + TYPEC_PORT_SNK, + TYPEC_PORT_DRP +} typec_port_type_t; + +typedef enum { + TYPEC_MSG_CTRL_RESERVED = 0, // 0b00000: 0 + TYPEC_MSG_CTRL_GOOD_CRC, // 0b00001: 1 + TYPEC_MSG_CTRL_GO_TO_MIN, // 0b00010: 2 + TYPEC_MSG_CTRL_ACCEPT, // 0b00011: 3 + TYPEC_MSG_CTRL_REJECT, // 0b00100: 4 + TYPEC_MSG_CTRL_PING, // 0b00101: 5 + TYPEC_MSG_CTRL_PS_RDY, // 0b00110: 6 + TYPEC_MSG_CTRL_GET_SOURCE_CAP, // 0b00111: 7 + TYPEC_MSG_CTRL_GET_SINK_CAP, // 0b01000: 8 + TYPEC_MSG_CTRL_DR_SWAP, // 0b01001: 9 + TYPEC_MSG_CTRL_PR_SWAP, // 0b01010: 10 + TYPEC_MSG_CTRL_VCONN_SWAP, // 0b01011: 11 + TYPEC_MSG_CTRL_WAIT, // 0b01100: 12 + TYPEC_MSG_CTRL_SOFT_RESET, // 0b01101: 13 + TYPEC_MSG_CTRL_DATA_RESET, // 0b01110: 14 + TYPEC_MSG_CTRL_DATA_RESET_COMPLETE, // 0b01111: 15 + TYPEC_MSG_CTRL_NOT_SUPPORTED, // 0b10000: 16 + TYPEC_MSG_CTRL_GET_SOURCE_CAP_EXTENDED, // 0b10001: 17 + TYPEC_MSG_CTRL_GET_STATUS, // 0b10010: 18 + TYPEC_MSG_CTRL_FR_SWAP, // 0b10011: 19 + TYPEC_MSG_CTRL_GET_PPS_STATUS, // 0b10100: 20 + TYPEC_MSG_CTRL_GET_COUNTRY_CODES, // 0b10101: 21 + TYPEC_MSG_CTRL_GET_SINK_CAP_EXTENDED, // 0b10110: 22 + TYPEC_MSG_CTRL_GET_SOURCE_INFO, // 0b10111: 23 + TYPEC_MSG_CTRL_REVISION, // 0b11000: 24 +} typec_msg_ctrl_type_t; + +typedef enum { + TYPEC_MSG_DATA_RESERVED = 0, // 0b00000: 0 + TYPEC_MSG_DATA_SOURCE_CAP, // 0b00001: 1 + TYPEC_MSG_DATA_REQUEST, // 0b00010: 2 + TYPEC_MSG_DATA_BIST, // 0b00011: 3 + TYPEC_MSG_DATA_SINK_CAP, // 0b00100: 4 + TYPEC_MSG_DATA_BATTERY_STATUS, // 0b00101: 5 + TYPEC_MSG_DATA_ALERT, // 0b00110: 6 + TYPEC_MSG_DATA_GET_COUNTRY_INFO, // 0b00111: 7 + TYPEC_MSG_DATA_ENTER_USB, // 0b01000: 8 + TYPEC_MSG_DATA_EPR_REQUEST, // 0b01001: 9 + TYPEC_MSG_DATA_EPR_MODE, // 0b01010: 10 + TYPEC_MSG_DATA_SRC_INFO, // 0b01011: 11 + TYPEC_MSG_DATA_REVISION, // 0b01100: 12 + TYPEC_MSG_DATA_RESERVED_13, // 0b01101: 13 + TYPEC_MSG_DATA_RESERVED_14, // 0b01110: 14 + TYPEC_MSG_DATA_VENDOR_DEFINED, // 0b01111: 15 +} typec_msg_data_type_t; + +typedef struct TU_ATTR_PACKED { + uint16_t msg_type : 5; // [0:4] + uint16_t data_role : 1; // [5] SOP only + uint16_t specs_rev : 2; // [6:7] + uint16_t power_role : 1; // [8] SOP only + uint16_t msg_id : 3; // [9:11] + uint16_t n_data_obj : 3; // [12:14] + uint16_t extended : 1; // [15] +} tusb_typec_message_header_t; + +typedef struct TU_ATTR_PACKED { + uint16_t data_size : 9; // [0:8] + uint16_t reserved : 1; // [9] + uint16_t request_chunk : 1; // [10] + uint16_t chunk_number : 4; // [11:14] + uint16_t chunked : 1; // [15] +} tusb_typec_message_header_extended_t; + TU_ATTR_PACKED_END // End of all packed definitions TU_ATTR_BIT_FIELD_ORDER_END diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c new file mode 100644 index 000000000..fd029473d --- /dev/null +++ b/src/portable/st/typec/typec_stm32.c @@ -0,0 +1,181 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#include "tusb_option.h" +#include "typec/tcd.h" + +#if CFG_TUC_ENABLED && defined(TUP_USBIP_TYPEC_STM32) + +#include "common/tusb_common.h" + +#include "stm32g4xx.h" + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ +uint8_t pd_rx_buf[262]; +uint32_t pd_rx_count = 0; +uint8_t pd_rx_order_set; + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +bool tcd_init(uint8_t rhport, typec_port_type_t port_type) { + (void) rhport; + + // Initialization phase: CFG1 + UCPD1->CFG1 = (0x0d << UCPD_CFG1_HBITCLKDIV_Pos) | (0x10 << UCPD_CFG1_IFRGAP_Pos) | (0x07 << UCPD_CFG1_TRANSWIN_Pos) | + (0x01 << UCPD_CFG1_PSC_UCPDCLK_Pos) | (0x1f << UCPD_CFG1_RXORDSETEN_Pos) | + (0 << UCPD_CFG1_TXDMAEN_Pos) | (0 << UCPD_CFG1_RXDMAEN_Pos); + UCPD1->CFG1 |= UCPD_CFG1_UCPDEN; + + // General programming sequence (with UCPD configured then enabled) + if (port_type == TYPEC_PORT_SNK) { + // Enable both CC Phy + UCPD1->CR = (0x01 << UCPD_CR_ANAMODE_Pos) | (0x03 << UCPD_CR_CCENABLE_Pos); + + // Read Voltage State on CC1 & CC2 fore initial state + uint32_t vstate_cc[2]; + vstate_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; + vstate_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; + + TU_LOG1_INT(vstate_cc[0]); + TU_LOG1_INT(vstate_cc[1]); + + // Enable CC1 & CC2 Interrupt + UCPD1->IMR = UCPD_IMR_TYPECEVT1IE | UCPD_IMR_TYPECEVT2IE; + } + + return true; +} + +// Enable interrupt +void tcd_int_enable (uint8_t rhport) { + (void) rhport; + NVIC_EnableIRQ(UCPD1_IRQn); +} + +// Disable interrupt +void tcd_int_disable(uint8_t rhport) { + (void) rhport; + NVIC_DisableIRQ(UCPD1_IRQn); +} + +void tcd_int_handler(uint8_t rhport) { + (void) rhport; + + uint32_t sr = UCPD1->SR; + sr &= UCPD1->IMR; + +// TU_LOG1("UCPD1_IRQHandler: sr = 0x%08X\n", sr); + + if (sr & (UCPD_SR_TYPECEVT1 | UCPD_SR_TYPECEVT2)) { + uint32_t vstate_cc[2]; + vstate_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; + vstate_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; + + TU_LOG1("VState CC1 = %u, CC2 = %u\n", vstate_cc[0], vstate_cc[1]); + + uint32_t cr = UCPD1->CR; + + // TODO only support SNK for now, required highest voltage for now + if ((sr & UCPD_SR_TYPECEVT1) && (vstate_cc[0] == 3)) { + TU_LOG1("Attach CC1\n"); + cr &= ~UCPD_CR_PHYCCSEL; + cr |= UCPD_CR_PHYRXEN; + } else if ((sr & UCPD_SR_TYPECEVT2) && (vstate_cc[1] == 3)) { + TU_LOG1("Attach CC2\n"); + cr |= UCPD_CR_PHYCCSEL; + cr |= UCPD_CR_PHYRXEN; + } else { + TU_LOG1("Detach\n"); + cr &= ~UCPD_CR_PHYRXEN; + } + + if (cr & UCPD_CR_PHYRXEN) { + // Enable Interrupt + UCPD1->IMR |= UCPD_IMR_TXMSGDISCIE | UCPD_IMR_TXMSGSENTIE | UCPD_IMR_TXMSGABTIE | UCPD_IMR_TXUNDIE | + UCPD_IMR_RXNEIE | UCPD_IMR_RXORDDETIE | UCPD_IMR_RXHRSTDETIE | UCPD_IMR_RXOVRIE | + UCPD_IMR_RXMSGENDIE | UCPD_IMR_HRSTDISCIE | UCPD_IMR_HRSTSENTIE; + } + + // Enable PD RX + UCPD1->CR = cr; + + // ack + UCPD1->ICR = UCPD_ICR_TYPECEVT1CF | UCPD_ICR_TYPECEVT2CF; + } + + //------------- Receive -------------// + if (sr & UCPD_SR_RXORDDET) { + // SOP: Start of Packet. + pd_rx_order_set = UCPD1->RX_ORDSET & UCPD_RX_ORDSET_RXORDSET_Msk; + + // reset count when received SOP + pd_rx_count = 0; + + // ack + UCPD1->ICR = UCPD_ICR_RXORDDETCF; + } + + if (sr & UCPD_SR_RXNE) { + // TODO DMA later + do { + pd_rx_buf[pd_rx_count++] = UCPD1->RXDR; + } while (UCPD1->SR & UCPD_SR_RXNE); + } + + if (sr & UCPD_SR_RXMSGEND) { + // End of message + + // Skip if CRC failed + if (!(sr & UCPD_SR_RXERR)) { + uint32_t payload_size = UCPD1->RX_PAYSZ; + TU_LOG1("RXMSGEND: payload_size = %u, rx count = %u\n", payload_size, pd_rx_count); + } + + // ack + UCPD1->ICR = UCPD_ICR_RXMSGENDCF; + } + + if (sr & UCPD_SR_RXOVR) { + TU_LOG1("RXOVR\n"); + TU_LOG1_HEX(pd_rx_count); + // ack + UCPD1->ICR = UCPD_ICR_RXOVRCF; + } + +// if (sr & UCPD_SR_RXNE) { +// uint8_t data = UCPD1->RXDR; +// pd_rx_buf[pd_rx_count++] = data; +// TU_LOG1_HEX(data); +// } + +// else { +// TU_LOG_LOCATION(); +// } +} + +#endif diff --git a/src/tusb.h b/src/tusb.h index b776d7d01..0b87b1969 100644 --- a/src/tusb.h +++ b/src/tusb.h @@ -40,6 +40,11 @@ #include "class/hid/hid.h" +//------------- TypeC -------------// +#if CFG_TUC_ENABLED + #include "typec/utcd.h" +#endif + //------------- HOST -------------// #if CFG_TUH_ENABLED #include "host/usbh.h" diff --git a/src/typec/tcd.h b/src/typec/tcd.h new file mode 100644 index 000000000..397c0ac83 --- /dev/null +++ b/src/typec/tcd.h @@ -0,0 +1,58 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (thach@tinyusb.org) for Adafruit Industries + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _TUSB_TCD_H_ +#define _TUSB_TCD_H_ + +#include "common/tusb_common.h" +#include "osal/osal.h" +#include "common/tusb_fifo.h" + +#ifdef __cplusplus +extern "C" { +#endif + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +// Initialize controller +bool tcd_init(uint8_t rhport, typec_port_type_t port_type); + +// Enable interrupt +void tcd_int_enable (uint8_t rhport); + +// Disable interrupt +void tcd_int_disable(uint8_t rhport); + +// Interrupt Handler +void tcd_int_handler(uint8_t rhport); + +#endif diff --git a/src/typec/utcd.c b/src/typec/utcd.c new file mode 100644 index 000000000..baa95fbe5 --- /dev/null +++ b/src/typec/utcd.c @@ -0,0 +1,48 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (thach@tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "tusb_option.h" + +#if CFG_TUC_ENABLED + +#include "tcd.h" + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +bool tuc_init(uint8_t rhport, typec_port_type_t port_type) { + TU_ASSERT(tcd_init(rhport, port_type)); + tcd_int_enable(rhport); + return true; +} + +#endif diff --git a/src/typec/utcd.h b/src/typec/utcd.h new file mode 100644 index 000000000..2f9b84fb7 --- /dev/null +++ b/src/typec/utcd.h @@ -0,0 +1,54 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _TUSB_UTCD_H_ +#define _TUSB_UTCD_H_ + +#include "common/tusb_common.h" + +#ifdef __cplusplus +extern "C" { +#endif + +//--------------------------------------------------------------------+ +// Application API +//--------------------------------------------------------------------+ + +// init typec stack +bool tuc_init(uint8_t rhport, typec_port_type_t port_type); + +#ifndef _TUSB_TCD_H_ +extern void tcd_int_handler(uint8_t rhport); +#endif + +// Interrupt handler, name alias to TCD +#define tuc_int_handler tcd_int_handler + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +#endif -- cgit v1.3.1 From 8bb012e50b39d9ed05c80509e69f9e26d463367c Mon Sep 17 00:00:00 2001 From: Aladdin Bakosh Date: Wed, 7 Jun 2023 12:01:59 +0200 Subject: fix(RA): static assert RUSB2 register --- src/portable/renesas/rusb2/rusb2_type.h | 1 + 1 file changed, 1 insertion(+) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index d80ecc62e..90ba4f012 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -1599,6 +1599,7 @@ TU_ATTR_BIT_FIELD_ORDER_END //--------------------------------------------------------------------+ TU_VERIFY_STATIC(sizeof(RUSB2_PIPE_TR_t) == 4, "incorrect size"); +TU_VERIFY_STATIC(sizeof(RUSB2_REG_t) == 1032, "incorrect size"); TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, SYSCFG ) == 0x00000000, "incorrect offset"); TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, BUSWAIT ) == 0x00000002, "incorrect offset"); -- cgit v1.3.1 From 9b7dee563e83a548f0d0fb68dd991a868a6427c9 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 7 Jun 2023 18:57:48 +0700 Subject: able to response with good crc --- examples/typec/power_delivery/src/main.c | 2 +- src/common/tusb_mcu.h | 5 ++ src/common/tusb_types.h | 112 +++++++++++++++++-------------- src/device/usbd.c | 10 +++ src/host/usbh.c | 2 +- src/portable/st/typec/typec_stm32.c | 105 +++++++++++++++++++++++++---- src/typec/tcd.h | 15 ++++- src/typec/utcd.c | 57 +++++++++++++++- src/typec/utcd.h | 16 ++++- 9 files changed, 253 insertions(+), 71 deletions(-) (limited to 'src/portable') diff --git a/examples/typec/power_delivery/src/main.c b/examples/typec/power_delivery/src/main.c index 9d032b6bb..648345a55 100644 --- a/examples/typec/power_delivery/src/main.c +++ b/examples/typec/power_delivery/src/main.c @@ -54,7 +54,7 @@ int main(void) board_init(); board_led_write(true); - tuc_init(0, TYPEC_PORT_SNK); + tuc_init(0, TUSB_TYPEC_PORT_SNK); uint32_t start_ms = 0; bool led_state = false; diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index bb4483f7d..f89467e75 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -197,12 +197,17 @@ #define TUP_DCD_ENDPOINT_MAX 9 #elif TU_CHECK_MCU(OPT_MCU_STM32G4) + // Device controller #define TUP_USBIP_FSDEV #define TUP_USBIP_FSDEV_STM32 + + // TypeC controller #define TUP_USBIP_TYPEC_STM32 #define TUP_DCD_ENDPOINT_MAX 8 + #define TUP_TYPEC_RHPORTS_NUM 1 + #elif TU_CHECK_MCU(OPT_MCU_STM32G0) #define TUP_USBIP_FSDEV #define TUP_USBIP_FSDEV_STM32 diff --git a/src/common/tusb_types.h b/src/common/tusb_types.h index e6b350a40..c92320e5c 100644 --- a/src/common/tusb_types.h +++ b/src/common/tusb_types.h @@ -504,67 +504,75 @@ TU_VERIFY_STATIC( sizeof(tusb_control_request_t) == 8, "size is not correct"); //--------------------------------------------------------------------+ typedef enum { - TYPEC_PORT_SRC, - TYPEC_PORT_SNK, - TYPEC_PORT_DRP -} typec_port_type_t; + TUSB_TYPEC_PORT_SRC, + TUSB_TYPEC_PORT_SNK, + TUSB_TYPEC_PORT_DRP +} tusb_typec_port_type_t; typedef enum { - TYPEC_MSG_CTRL_RESERVED = 0, // 0b00000: 0 - TYPEC_MSG_CTRL_GOOD_CRC, // 0b00001: 1 - TYPEC_MSG_CTRL_GO_TO_MIN, // 0b00010: 2 - TYPEC_MSG_CTRL_ACCEPT, // 0b00011: 3 - TYPEC_MSG_CTRL_REJECT, // 0b00100: 4 - TYPEC_MSG_CTRL_PING, // 0b00101: 5 - TYPEC_MSG_CTRL_PS_RDY, // 0b00110: 6 - TYPEC_MSG_CTRL_GET_SOURCE_CAP, // 0b00111: 7 - TYPEC_MSG_CTRL_GET_SINK_CAP, // 0b01000: 8 - TYPEC_MSG_CTRL_DR_SWAP, // 0b01001: 9 - TYPEC_MSG_CTRL_PR_SWAP, // 0b01010: 10 - TYPEC_MSG_CTRL_VCONN_SWAP, // 0b01011: 11 - TYPEC_MSG_CTRL_WAIT, // 0b01100: 12 - TYPEC_MSG_CTRL_SOFT_RESET, // 0b01101: 13 - TYPEC_MSG_CTRL_DATA_RESET, // 0b01110: 14 - TYPEC_MSG_CTRL_DATA_RESET_COMPLETE, // 0b01111: 15 - TYPEC_MSG_CTRL_NOT_SUPPORTED, // 0b10000: 16 - TYPEC_MSG_CTRL_GET_SOURCE_CAP_EXTENDED, // 0b10001: 17 - TYPEC_MSG_CTRL_GET_STATUS, // 0b10010: 18 - TYPEC_MSG_CTRL_FR_SWAP, // 0b10011: 19 - TYPEC_MSG_CTRL_GET_PPS_STATUS, // 0b10100: 20 - TYPEC_MSG_CTRL_GET_COUNTRY_CODES, // 0b10101: 21 - TYPEC_MSG_CTRL_GET_SINK_CAP_EXTENDED, // 0b10110: 22 - TYPEC_MSG_CTRL_GET_SOURCE_INFO, // 0b10111: 23 - TYPEC_MSG_CTRL_REVISION, // 0b11000: 24 -} typec_msg_ctrl_type_t; + TUSB_PD_CTRL_RESERVED = 0, // 0b00000: 0 + TUSB_PD_CTRL_GOOD_CRC, // 0b00001: 1 + TUSB_PD_CTRL_GO_TO_MIN, // 0b00010: 2 + TUSB_PD_CTRL_ACCEPT, // 0b00011: 3 + TUSB_PD_CTRL_REJECT, // 0b00100: 4 + TUSB_PD_CTRL_PING, // 0b00101: 5 + TUSB_PD_CTRL_PS_RDY, // 0b00110: 6 + TUSB_PD_CTRL_GET_SOURCE_CAP, // 0b00111: 7 + TUSB_PD_CTRL_GET_SINK_CAP, // 0b01000: 8 + TUSB_PD_CTRL_DR_SWAP, // 0b01001: 9 + TUSB_PD_CTRL_PR_SWAP, // 0b01010: 10 + TUSB_PD_CTRL_VCONN_SWAP, // 0b01011: 11 + TUSB_PD_CTRL_WAIT, // 0b01100: 12 + TUSB_PD_CTRL_SOFT_RESET, // 0b01101: 13 + TUSB_PD_CTRL_DATA_RESET, // 0b01110: 14 + TUSB_PD_CTRL_DATA_RESET_COMPLETE, // 0b01111: 15 + TUSB_PD_CTRL_NOT_SUPPORTED, // 0b10000: 16 + TUSB_PD_CTRL_GET_SOURCE_CAP_EXTENDED, // 0b10001: 17 + TUSB_PD_CTRL_GET_STATUS, // 0b10010: 18 + TUSB_PD_CTRL_FR_SWAP, // 0b10011: 19 + TUSB_PD_CTRL_GET_PPS_STATUS, // 0b10100: 20 + TUSB_PD_CTRL_GET_COUNTRY_CODES, // 0b10101: 21 + TUSB_PD_CTRL_GET_SINK_CAP_EXTENDED, // 0b10110: 22 + TUSB_PD_CTRL_GET_SOURCE_INFO, // 0b10111: 23 + TUSB_PD_CTRL_REVISION, // 0b11000: 24 +} tusb_pd_ctrl_type_t; typedef enum { - TYPEC_MSG_DATA_RESERVED = 0, // 0b00000: 0 - TYPEC_MSG_DATA_SOURCE_CAP, // 0b00001: 1 - TYPEC_MSG_DATA_REQUEST, // 0b00010: 2 - TYPEC_MSG_DATA_BIST, // 0b00011: 3 - TYPEC_MSG_DATA_SINK_CAP, // 0b00100: 4 - TYPEC_MSG_DATA_BATTERY_STATUS, // 0b00101: 5 - TYPEC_MSG_DATA_ALERT, // 0b00110: 6 - TYPEC_MSG_DATA_GET_COUNTRY_INFO, // 0b00111: 7 - TYPEC_MSG_DATA_ENTER_USB, // 0b01000: 8 - TYPEC_MSG_DATA_EPR_REQUEST, // 0b01001: 9 - TYPEC_MSG_DATA_EPR_MODE, // 0b01010: 10 - TYPEC_MSG_DATA_SRC_INFO, // 0b01011: 11 - TYPEC_MSG_DATA_REVISION, // 0b01100: 12 - TYPEC_MSG_DATA_RESERVED_13, // 0b01101: 13 - TYPEC_MSG_DATA_RESERVED_14, // 0b01110: 14 - TYPEC_MSG_DATA_VENDOR_DEFINED, // 0b01111: 15 -} typec_msg_data_type_t; + TUSB_PD_DATA_RESERVED = 0, // 0b00000: 0 + TUSB_PD_DATA_SOURCE_CAP, // 0b00001: 1 + TUSB_PD_DATA_REQUEST, // 0b00010: 2 + TUSB_PD_DATA_BIST, // 0b00011: 3 + TUSB_PD_DATA_SINK_CAP, // 0b00100: 4 + TUSB_PD_DATA_BATTERY_STATUS, // 0b00101: 5 + TUSB_PD_DATA_ALERT, // 0b00110: 6 + TUSB_PD_DATA_GET_COUNTRY_INFO, // 0b00111: 7 + TUSB_PD_DATA_ENTER_USB, // 0b01000: 8 + TUSB_PD_DATA_EPR_REQUEST, // 0b01001: 9 + TUSB_PD_DATA_EPR_MODE, // 0b01010: 10 + TUSB_PD_DATA_SRC_INFO, // 0b01011: 11 + TUSB_PD_DATA_REVISION, // 0b01100: 12 + TUSB_PD_DATA_RESERVED_13, // 0b01101: 13 + TUSB_PD_DATA_RESERVED_14, // 0b01110: 14 + TUSB_PD_DATA_VENDOR_DEFINED, // 0b01111: 15 +} tusb_pd_data_type_t; + +enum { + TUSB_PD_REV10 = 0x0, + TUSB_PD_REV20 = 0x1, + TUSB_PD_REV30 = 0x2, +}; typedef struct TU_ATTR_PACKED { uint16_t msg_type : 5; // [0:4] - uint16_t data_role : 1; // [5] SOP only + uint16_t data_role : 1; // [5] SOP only: 0 UFP, 1 DFP uint16_t specs_rev : 2; // [6:7] - uint16_t power_role : 1; // [8] SOP only + uint16_t power_role : 1; // [8] SOP only: 0 Sink, 1 Source uint16_t msg_id : 3; // [9:11] uint16_t n_data_obj : 3; // [12:14] uint16_t extended : 1; // [15] -} tusb_typec_message_header_t; +} tusb_pd_header_t; + +TU_VERIFY_STATIC( sizeof(tusb_pd_header_t) == 2, "size is not correct"); typedef struct TU_ATTR_PACKED { uint16_t data_size : 9; // [0:8] @@ -572,7 +580,9 @@ typedef struct TU_ATTR_PACKED { uint16_t request_chunk : 1; // [10] uint16_t chunk_number : 4; // [11:14] uint16_t chunked : 1; // [15] -} tusb_typec_message_header_extended_t; +} tusb_pd_header_extended_t; + +TU_VERIFY_STATIC( sizeof(tusb_pd_header_extended_t) == 2, "size is not correct"); TU_ATTR_PACKED_END // End of all packed definitions diff --git a/src/device/usbd.c b/src/device/usbd.c index 409a5ec10..44c2530ce 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -252,9 +252,19 @@ static inline usbd_class_driver_t const * get_driver(uint8_t drvid) drvid -= _app_driver_count; } + // when there is no built-in drivers BUILTIN_DRIVER_COUNT = 0 will cause -Wtype-limits warning +#ifdef __GNUC__ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wtype-limits" +#endif + // Built-in drivers if (drvid < BUILTIN_DRIVER_COUNT) return &_usbd_driver[drvid]; +#ifdef __GNUC__ +#pragma GCC diagnostic pop +#endif + return NULL; } diff --git a/src/host/usbh.c b/src/host/usbh.c index 6159044ab..98e959a12 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -724,7 +724,7 @@ uint8_t* usbh_get_enum_buf(void) void usbh_int_set(bool enabled) { - // TODO all host controller if multiple is used + // TODO all host controller if multiple are used since they shared the same event queue if (enabled) { hcd_int_enable(_usbh_controller); diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index fd029473d..79f37b729 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -29,20 +29,43 @@ #include "common/tusb_common.h" -#include "stm32g4xx.h" +#if CFG_TUSB_MCU == OPT_MCU_STM32G4 + #include "stm32g4xx.h" +#else + #error "Unsupported STM32 family" +#endif //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ -uint8_t pd_rx_buf[262]; -uint32_t pd_rx_count = 0; -uint8_t pd_rx_order_set; + +#define PHY_SYNC1 0x18u +#define PHY_SYNC2 0x11u +#define PHY_SYNC3 0x06u +#define PHY_RST1 0x07u +#define PHY_RST2 0x19u +#define PHY_EOP 0x0Du + +#define PHY_ORDERED_SET_SOP (PHY_SYNC1 | (PHY_SYNC1<<5u) | (PHY_SYNC1<<10u) | (PHY_SYNC2<<15u)) // SOP Ordered set coding +#define PHY_ORDERED_SET_SOP_P (PHY_SYNC1 | (PHY_SYNC1<<5u) | (PHY_SYNC3<<10u) | (PHY_SYNC3<<15u)) // SOP' Ordered set coding +#define PHY_ORDERED_SET_SOP_PP (PHY_SYNC1 | (PHY_SYNC3<<5u) | (PHY_SYNC1<<10u) | (PHY_SYNC3<<15u)) // SOP'' Ordered set coding +#define PHY_ORDERED_SET_HARD_RESET (PHY_RST1 | (PHY_RST1<<5u) | (PHY_RST1<<10u) | (PHY_RST2<<15u )) // Hard Reset Ordered set coding +#define PHY_ORDERED_SET_CABLE_RESET (PHY_RST1 | (PHY_SYNC1<<5u) | (PHY_RST1<<10u) | (PHY_SYNC3<<15u)) // Cable Reset Ordered set coding +#define PHY_ORDERED_SET_SOP_P_DEBUG (PHY_SYNC1 | (PHY_RST2<<5u) | (PHY_RST2<<10u) | (PHY_SYNC3<<15u)) // SOP' Debug Ordered set coding +#define PHY_ORDERED_SET_SOP_PP_DEBUG (PHY_SYNC1 | (PHY_RST2<<5u) | (PHY_SYNC3<<10u) | (PHY_SYNC2<<15u)) // SOP'' Debug Ordered set coding + + +static uint8_t rx_buf[262] TU_ATTR_ALIGNED(4); +static uint32_t rx_count = 0; + +static uint8_t tx_buf[262] TU_ATTR_ALIGNED(4); +static uint32_t tx_count; //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ -bool tcd_init(uint8_t rhport, typec_port_type_t port_type) { +bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type) { (void) rhport; // Initialization phase: CFG1 @@ -52,7 +75,7 @@ bool tcd_init(uint8_t rhport, typec_port_type_t port_type) { UCPD1->CFG1 |= UCPD_CFG1_UCPDEN; // General programming sequence (with UCPD configured then enabled) - if (port_type == TYPEC_PORT_SNK) { + if (port_type == TUSB_TYPEC_PORT_SNK) { // Enable both CC Phy UCPD1->CR = (0x01 << UCPD_CR_ANAMODE_Pos) | (0x03 << UCPD_CR_CCENABLE_Pos); @@ -83,6 +106,19 @@ void tcd_int_disable(uint8_t rhport) { NVIC_DisableIRQ(UCPD1_IRQn); } +bool tcd_rx_start(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes) { + (void) rhport; + + return true; +} + +bool tcd_tx_start(uint8_t rhport, uint8_t const* buffer, uint16_t total_bytes) { + (void) rhport; + (void) buffer; + (void) total_bytes; + return false; +} + void tcd_int_handler(uint8_t rhport) { (void) rhport; @@ -116,7 +152,7 @@ void tcd_int_handler(uint8_t rhport) { if (cr & UCPD_CR_PHYRXEN) { // Enable Interrupt - UCPD1->IMR |= UCPD_IMR_TXMSGDISCIE | UCPD_IMR_TXMSGSENTIE | UCPD_IMR_TXMSGABTIE | UCPD_IMR_TXUNDIE | + UCPD1->IMR |= UCPD_IMR_TXISIE | UCPD_IMR_TXMSGDISCIE | UCPD_IMR_TXMSGSENTIE | UCPD_IMR_TXMSGABTIE | UCPD_IMR_TXUNDIE | UCPD_IMR_RXNEIE | UCPD_IMR_RXORDDETIE | UCPD_IMR_RXHRSTDETIE | UCPD_IMR_RXOVRIE | UCPD_IMR_RXMSGENDIE | UCPD_IMR_HRSTDISCIE | UCPD_IMR_HRSTSENTIE; } @@ -128,13 +164,13 @@ void tcd_int_handler(uint8_t rhport) { UCPD1->ICR = UCPD_ICR_TYPECEVT1CF | UCPD_ICR_TYPECEVT2CF; } - //------------- Receive -------------// + //------------- RX -------------// if (sr & UCPD_SR_RXORDDET) { // SOP: Start of Packet. - pd_rx_order_set = UCPD1->RX_ORDSET & UCPD_RX_ORDSET_RXORDSET_Msk; + // UCPD1->RX_ORDSET & UCPD_RX_ORDSET_RXORDSET_Msk; // reset count when received SOP - pd_rx_count = 0; + rx_count = 0; // ack UCPD1->ICR = UCPD_ICR_RXORDDETCF; @@ -143,17 +179,38 @@ void tcd_int_handler(uint8_t rhport) { if (sr & UCPD_SR_RXNE) { // TODO DMA later do { - pd_rx_buf[pd_rx_count++] = UCPD1->RXDR; + rx_buf[rx_count++] = UCPD1->RXDR; } while (UCPD1->SR & UCPD_SR_RXNE); + + // no ack needed } + // End of message if (sr & UCPD_SR_RXMSGEND) { - // End of message // Skip if CRC failed if (!(sr & UCPD_SR_RXERR)) { uint32_t payload_size = UCPD1->RX_PAYSZ; - TU_LOG1("RXMSGEND: payload_size = %u, rx count = %u\n", payload_size, pd_rx_count); + // TU_LOG1("RXMSGEND: payload_size = %u, rx count = %u\n", payload_size, pd_rx_count); + + tusb_pd_header_t const* rx_header = (tusb_pd_header_t const*) rx_buf; + (*(tusb_pd_header_t*) tx_buf) = (tusb_pd_header_t) { + .msg_type = TUSB_PD_CTRL_GOOD_CRC, + .data_role = 0, // UFP + .specs_rev = TUSB_PD_REV30, + .power_role = 0, // Sink + .msg_id = rx_header->msg_id, + .n_data_obj = 0, + .extended = 0 + }; + tx_count = 0; + + // response with good crc + UCPD1->TX_ORDSET = PHY_ORDERED_SET_SOP; + UCPD1->TX_PAYSZ = 2; + UCPD1->CR |= UCPD_CR_TXSEND; // will trigger TXIS interrupt + + // notify stack after good crc ? } // ack @@ -162,11 +219,31 @@ void tcd_int_handler(uint8_t rhport) { if (sr & UCPD_SR_RXOVR) { TU_LOG1("RXOVR\n"); - TU_LOG1_HEX(pd_rx_count); + TU_LOG1_HEX(rx_count); // ack UCPD1->ICR = UCPD_ICR_RXOVRCF; } + //------------- TX -------------// + if (sr & UCPD_SR_TXIS) { + // TU_LOG1("TXIS\n"); + + // TODO DMA later + do { + UCPD1->TXDR = tx_buf[tx_count++]; + } while (UCPD1->SR & UCPD_SR_TXIS); + + // no ack needed + } + + if (sr & UCPD_SR_TXMSGSENT) { + // all byte sent + TU_LOG1("TXMSGSENT\n"); + + // ack + UCPD1->ICR = UCPD_ICR_TXMSGSENTCF; + } + // if (sr & UCPD_SR_RXNE) { // uint8_t data = UCPD1->RXDR; // pd_rx_buf[pd_rx_count++] = data; diff --git a/src/typec/tcd.h b/src/typec/tcd.h index 397c0ac83..e823bf8d7 100644 --- a/src/typec/tcd.h +++ b/src/typec/tcd.h @@ -38,13 +38,19 @@ extern "C" { //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ +typedef struct { + uint8_t rhport; + uint8_t event_id; + + +} tcd_event_t;; //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ // Initialize controller -bool tcd_init(uint8_t rhport, typec_port_type_t port_type); +bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type); // Enable interrupt void tcd_int_enable (uint8_t rhport); @@ -55,4 +61,11 @@ void tcd_int_disable(uint8_t rhport); // Interrupt Handler void tcd_int_handler(uint8_t rhport); +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +bool tcd_rx_start(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes); +bool tcd_tx_start(uint8_t rhport, uint8_t const* buffer, uint16_t total_bytes); + #endif diff --git a/src/typec/utcd.c b/src/typec/utcd.c index baa95fbe5..b5f9965fe 100644 --- a/src/typec/utcd.c +++ b/src/typec/utcd.c @@ -29,20 +29,75 @@ #if CFG_TUC_ENABLED #include "tcd.h" +#include "utcd.h" //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ +// Debug level of USBD +#define UTCD_DEBUG 2 +#define TU_LOG_UTCD(...) TU_LOG(UTCD_DEBUG, __VA_ARGS__) + +// Event queue +// utcd_int_set() is used as mutex in OS NONE config +void utcd_int_set(bool enabled); +OSAL_QUEUE_DEF(utcd_int_set, utcd_qdef, CFG_TUC_TASK_QUEUE_SZ, tcd_event_t); +tu_static osal_queue_t utcd_q; + +// if stack is initialized +static bool utcd_inited = false; + +// if port is initialized +static bool port_inited[TUP_TYPEC_RHPORTS_NUM]; //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ +bool tuc_inited(uint8_t rhport) { + return utcd_inited && port_inited[rhport]; +} + +bool tuc_init(uint8_t rhport, tusb_typec_port_type_t port_type) { + // Initialize stack + if (!utcd_inited) { + tu_memclr(port_inited, sizeof(port_inited)); + + utcd_q = osal_queue_create(&utcd_qdef); + TU_ASSERT(utcd_q != NULL); + + utcd_inited = true; + } + + // skip if port already initialized + if ( port_inited[rhport] ) { + return true; + } + + TU_LOG_UTCD("UTCD init on port %u\r\n", rhport); -bool tuc_init(uint8_t rhport, typec_port_type_t port_type) { TU_ASSERT(tcd_init(rhport, port_type)); tcd_int_enable(rhport); + + port_inited[rhport] = true; return true; } + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ +void utcd_int_set(bool enabled) { + // Disable all controllers since they shared the same event queue + for (uint8_t p = 0; p < TUP_TYPEC_RHPORTS_NUM; p++) { + if ( port_inited[p] ) { + if (enabled) { + tcd_int_enable(p); + }else { + tcd_int_disable(p); + } + } + } +} + #endif diff --git a/src/typec/utcd.h b/src/typec/utcd.h index 2f9b84fb7..06a62ef23 100644 --- a/src/typec/utcd.h +++ b/src/typec/utcd.h @@ -33,12 +33,24 @@ extern "C" { #endif +//--------------------------------------------------------------------+ +// TypeC Configuration +//--------------------------------------------------------------------+ + +#ifndef CFG_TUC_TASK_QUEUE_SZ +#define CFG_TUC_TASK_QUEUE_SZ 16 +#endif + + //--------------------------------------------------------------------+ // Application API //--------------------------------------------------------------------+ -// init typec stack -bool tuc_init(uint8_t rhport, typec_port_type_t port_type); +// Init typec stack on a port +bool tuc_init(uint8_t rhport, tusb_typec_port_type_t port_type); + +// Check if typec port is initialized +bool tuc_inited(uint8_t rhport); #ifndef _TUSB_TCD_H_ extern void tcd_int_handler(uint8_t rhport); -- cgit v1.3.1 From 9c2a8490afadd47d5847793a806e2dce51565868 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 8 Jun 2023 13:37:37 +0700 Subject: dma rx works well --- .../stm32g4/boards/b_g474e_dpow1/cubemx/board.ioc | 194 +++++++++++++++++++++ hw/bsp/stm32g4/family.c | 7 +- src/portable/st/typec/typec_stm32.c | 80 +++++++-- 3 files changed, 267 insertions(+), 14 deletions(-) create mode 100644 hw/bsp/stm32g4/boards/b_g474e_dpow1/cubemx/board.ioc (limited to 'src/portable') diff --git a/hw/bsp/stm32g4/boards/b_g474e_dpow1/cubemx/board.ioc b/hw/bsp/stm32g4/boards/b_g474e_dpow1/cubemx/board.ioc new file mode 100644 index 000000000..6ce126f84 --- /dev/null +++ b/hw/bsp/stm32g4/boards/b_g474e_dpow1/cubemx/board.ioc @@ -0,0 +1,194 @@ +#MicroXplorer Configuration settings - do not modify +CAD.formats= +CAD.pinconfig= +CAD.provider= +Dma.Request0=UCPD1_RX +Dma.Request1=UCPD1_TX +Dma.RequestsNb=2 +Dma.UCPD1_RX.0.Direction=DMA_PERIPH_TO_MEMORY +Dma.UCPD1_RX.0.EventEnable=DISABLE +Dma.UCPD1_RX.0.Instance=DMA1_Channel1 +Dma.UCPD1_RX.0.MemDataAlignment=DMA_MDATAALIGN_BYTE +Dma.UCPD1_RX.0.MemInc=DMA_MINC_ENABLE +Dma.UCPD1_RX.0.Mode=DMA_NORMAL +Dma.UCPD1_RX.0.PeriphDataAlignment=DMA_PDATAALIGN_BYTE +Dma.UCPD1_RX.0.PeriphInc=DMA_PINC_DISABLE +Dma.UCPD1_RX.0.Polarity=HAL_DMAMUX_REQ_GEN_RISING +Dma.UCPD1_RX.0.Priority=DMA_PRIORITY_HIGH +Dma.UCPD1_RX.0.RequestNumber=1 +Dma.UCPD1_RX.0.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,SignalID,Polarity,RequestNumber,SyncSignalID,SyncPolarity,SyncEnable,EventEnable,SyncRequestNumber +Dma.UCPD1_RX.0.SignalID=NONE +Dma.UCPD1_RX.0.SyncEnable=DISABLE +Dma.UCPD1_RX.0.SyncPolarity=HAL_DMAMUX_SYNC_NO_EVENT +Dma.UCPD1_RX.0.SyncRequestNumber=1 +Dma.UCPD1_RX.0.SyncSignalID=NONE +Dma.UCPD1_TX.1.Direction=DMA_MEMORY_TO_PERIPH +Dma.UCPD1_TX.1.EventEnable=DISABLE +Dma.UCPD1_TX.1.Instance=DMA1_Channel2 +Dma.UCPD1_TX.1.MemDataAlignment=DMA_MDATAALIGN_BYTE +Dma.UCPD1_TX.1.MemInc=DMA_MINC_ENABLE +Dma.UCPD1_TX.1.Mode=DMA_NORMAL +Dma.UCPD1_TX.1.PeriphDataAlignment=DMA_PDATAALIGN_BYTE +Dma.UCPD1_TX.1.PeriphInc=DMA_PINC_DISABLE +Dma.UCPD1_TX.1.Polarity=HAL_DMAMUX_REQ_GEN_RISING +Dma.UCPD1_TX.1.Priority=DMA_PRIORITY_HIGH +Dma.UCPD1_TX.1.RequestNumber=1 +Dma.UCPD1_TX.1.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,SignalID,Polarity,RequestNumber,SyncSignalID,SyncPolarity,SyncEnable,EventEnable,SyncRequestNumber +Dma.UCPD1_TX.1.SignalID=NONE +Dma.UCPD1_TX.1.SyncEnable=DISABLE +Dma.UCPD1_TX.1.SyncPolarity=HAL_DMAMUX_SYNC_NO_EVENT +Dma.UCPD1_TX.1.SyncRequestNumber=1 +Dma.UCPD1_TX.1.SyncSignalID=NONE +File.Version=6 +GPIO.groupedBy=Group By Peripherals +KeepUserPlacement=true +Mcu.CPN=STM32G474RET3 +Mcu.Family=STM32G4 +Mcu.IP0=DMA +Mcu.IP1=NVIC +Mcu.IP2=RCC +Mcu.IP3=SYS +Mcu.IP4=UCPD1 +Mcu.IP5=USART3 +Mcu.IPNb=6 +Mcu.Name=STM32G474R(B-C-E)Tx +Mcu.Package=LQFP64 +Mcu.Pin0=PC10 +Mcu.Pin1=PC11 +Mcu.Pin2=PB4 +Mcu.Pin3=PB6 +Mcu.Pin4=VP_SYS_VS_Systick +Mcu.Pin5=VP_SYS_VS_DBSignals +Mcu.PinsNb=6 +Mcu.ThirdPartyNb=0 +Mcu.UserConstants= +Mcu.UserName=STM32G474RETx +MxCube.Version=6.8.1 +MxDb.Version=DB.6.0.81 +NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:false\:true\:false\:false +NVIC.DMA1_Channel1_IRQn=true\:0\:0\:false\:false\:true\:false\:true\:true +NVIC.DMA1_Channel2_IRQn=true\:0\:0\:false\:false\:true\:false\:true\:true +NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:false\:true\:false\:false +NVIC.ForceEnableDMAVector=true +NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false +NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:false\:true\:false\:false +NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false +NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:true\:false\:false +NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4 +NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:true\:false\:false +NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:true\:true\:false +NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:false\:true\:false\:false +PB4.Mode=Sink_AllSignals +PB4.Signal=UCPD1_CC2 +PB6.Mode=Sink_AllSignals +PB6.Signal=UCPD1_CC1 +PC10.GPIOParameters=GPIO_PuPd +PC10.GPIO_PuPd=GPIO_PULLUP +PC10.Mode=Asynchronous +PC10.Signal=USART3_TX +PC11.GPIOParameters=GPIO_PuPd +PC11.GPIO_PuPd=GPIO_PULLUP +PC11.Mode=Asynchronous +PC11.Signal=USART3_RX +PinOutPanel.RotationAngle=0 +ProjectManager.AskForMigrate=true +ProjectManager.BackupPrevious=false +ProjectManager.CompilerOptimize=6 +ProjectManager.ComputerToolchain=false +ProjectManager.CoupleFile=false +ProjectManager.CustomerFirmwarePackage= +ProjectManager.DefaultFWLocation=true +ProjectManager.DeletePrevious=true +ProjectManager.DeviceId=STM32G474RETx +ProjectManager.FirmwarePackage=STM32Cube FW_G4 V1.5.1 +ProjectManager.FreePins=false +ProjectManager.HalAssertFull=false +ProjectManager.HeapSize=0x200 +ProjectManager.KeepUserCode=true +ProjectManager.LastFirmware=true +ProjectManager.LibraryCopy=2 +ProjectManager.MainLocation=Src +ProjectManager.NoMain=false +ProjectManager.PreviousToolchain= +ProjectManager.ProjectBuild=false +ProjectManager.ProjectFileName=board.ioc +ProjectManager.ProjectName=board +ProjectManager.ProjectStructure= +ProjectManager.RegisterCallBack= +ProjectManager.StackSize=0x400 +ProjectManager.TargetToolchain=Makefile +ProjectManager.ToolChainLocation= +ProjectManager.UnderRoot=false +ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-SystemClock_Config-RCC-false-HAL-false,3-MX_DMA_Init-DMA-false-HAL-true,4-MX_USART3_UART_Init-USART3-false-HAL-true,5-MX_UCPD1_Init-UCPD1-false-LL-true +RCC.ADC12Freq_Value=150000000 +RCC.ADC345Freq_Value=150000000 +RCC.AHBFreq_Value=150000000 +RCC.APB1Freq_Value=150000000 +RCC.APB1TimFreq_Value=150000000 +RCC.APB2Freq_Value=150000000 +RCC.APB2TimFreq_Value=150000000 +RCC.CRSFreq_Value=48000000 +RCC.CortexFreq_Value=150000000 +RCC.EXTERNAL_CLOCK_VALUE=12288000 +RCC.FCLKCortexFreq_Value=150000000 +RCC.FDCANFreq_Value=150000000 +RCC.FamilyName=M +RCC.HCLKFreq_Value=150000000 +RCC.HRTIM1Freq_Value=150000000 +RCC.HSE_VALUE=24000000 +RCC.HSI48_VALUE=48000000 +RCC.HSI_VALUE=16000000 +RCC.I2C1Freq_Value=150000000 +RCC.I2C2Freq_Value=150000000 +RCC.I2C3Freq_Value=150000000 +RCC.I2C4Freq_Value=150000000 +RCC.I2SFreq_Value=150000000 +RCC.IPParameters=ADC12Freq_Value,ADC345Freq_Value,AHBFreq_Value,APB1Freq_Value,APB1TimFreq_Value,APB2Freq_Value,APB2TimFreq_Value,CRSFreq_Value,CortexFreq_Value,EXTERNAL_CLOCK_VALUE,FCLKCortexFreq_Value,FDCANFreq_Value,FamilyName,HCLKFreq_Value,HRTIM1Freq_Value,HSE_VALUE,HSI48_VALUE,HSI_VALUE,I2C1Freq_Value,I2C2Freq_Value,I2C3Freq_Value,I2C4Freq_Value,I2SFreq_Value,LPTIM1Freq_Value,LPUART1Freq_Value,LSCOPinFreq_Value,LSE_VALUE,LSI_VALUE,MCO1PinFreq_Value,PLLM,PLLN,PLLPoutputFreq_Value,PLLQ,PLLQoutputFreq_Value,PLLRCLKFreq_Value,PWRFreq_Value,QSPIFreq_Value,RNGFreq_Value,SAI1Freq_Value,SYSCLKFreq_VALUE,SYSCLKSource,UART4Freq_Value,UART5Freq_Value,USART1Freq_Value,USART2Freq_Value,USART3Freq_Value,USBFreq_Value,VCOInputFreq_Value,VCOOutputFreq_Value +RCC.LPTIM1Freq_Value=150000000 +RCC.LPUART1Freq_Value=150000000 +RCC.LSCOPinFreq_Value=32000 +RCC.LSE_VALUE=32768 +RCC.LSI_VALUE=32000 +RCC.MCO1PinFreq_Value=16000000 +RCC.PLLM=RCC_PLLM_DIV4 +RCC.PLLN=75 +RCC.PLLPoutputFreq_Value=150000000 +RCC.PLLQ=RCC_PLLQ_DIV4 +RCC.PLLQoutputFreq_Value=75000000 +RCC.PLLRCLKFreq_Value=150000000 +RCC.PWRFreq_Value=150000000 +RCC.QSPIFreq_Value=150000000 +RCC.RNGFreq_Value=75000000 +RCC.SAI1Freq_Value=150000000 +RCC.SYSCLKFreq_VALUE=150000000 +RCC.SYSCLKSource=RCC_SYSCLKSOURCE_PLLCLK +RCC.UART4Freq_Value=150000000 +RCC.UART5Freq_Value=150000000 +RCC.USART1Freq_Value=150000000 +RCC.USART2Freq_Value=150000000 +RCC.USART3Freq_Value=150000000 +RCC.USBFreq_Value=75000000 +RCC.VCOInputFreq_Value=4000000 +RCC.VCOOutputFreq_Value=300000000 +USART3.AutoBaudRateEnableParam=UART_ADVFEATURE_AUTOBAUDRATE_DISABLE +USART3.BaudRate=115200 +USART3.DMADisableonRxErrorParam=ADVFEATURE_DMA_ENABLEONRXERROR +USART3.DataInvertParam=ADVFEATURE_DATAINV_DISABLE +USART3.IPParameters=BaudRate,WordLength,Parity,StopBits,Mode,OverSampling,OneBitSampling,AutoBaudRateEnableParam,TxPinLevelInvertParam,RxPinLevelInvertParam,DataInvertParam,SwapParam,OverrunDisableParam,DMADisableonRxErrorParam,MSBFirstParam,VirtualMode-Asynchronous +USART3.MSBFirstParam=ADVFEATURE_MSBFIRST_DISABLE +USART3.Mode=MODE_TX_RX +USART3.OneBitSampling=UART_ONE_BIT_SAMPLE_DISABLE +USART3.OverSampling=UART_OVERSAMPLING_16 +USART3.OverrunDisableParam=ADVFEATURE_OVERRUN_ENABLE +USART3.Parity=PARITY_ODD +USART3.RxPinLevelInvertParam=ADVFEATURE_RXINV_DISABLE +USART3.StopBits=STOPBITS_1 +USART3.SwapParam=ADVFEATURE_SWAP_DISABLE +USART3.TxPinLevelInvertParam=ADVFEATURE_TXINV_DISABLE +USART3.VirtualMode-Asynchronous=VM_ASYNC +USART3.WordLength=WORDLENGTH_8B +VP_SYS_VS_DBSignals.Mode=DisableDeadBatterySignals +VP_SYS_VS_DBSignals.Signal=SYS_VS_DBSignals +VP_SYS_VS_Systick.Mode=SysTick +VP_SYS_VS_Systick.Signal=SYS_VS_Systick +board=custom diff --git a/hw/bsp/stm32g4/family.c b/hw/bsp/stm32g4/family.c index d0601b385..5fa6e3dbb 100644 --- a/hw/bsp/stm32g4/family.c +++ b/hw/bsp/stm32g4/family.c @@ -144,15 +144,16 @@ void board_init(void) #if 1 // USB PD + // Default CC1/CC2 is PB4/PB6 /* PWR register access (for disabling dead battery feature) */ LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_PWR); LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_CRC); __HAL_RCC_UCPD1_CLK_ENABLE(); - // Default CC1/CC2 is PB4/PB6 - // PB4 ------> UCPD1_CC2 - // PB6 ------> UCPD1_CC1 + // Enable DMA clock + __HAL_RCC_DMAMUX1_CLK_ENABLE(); + __HAL_RCC_DMA1_CLK_ENABLE(); #endif } diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index 79f37b729..c96dd0902 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -31,6 +31,7 @@ #if CFG_TUSB_MCU == OPT_MCU_STM32G4 #include "stm32g4xx.h" + #include "stm32g4xx_hal_dma.h" #else #error "Unsupported STM32 family" #endif @@ -61,13 +62,46 @@ static uint32_t rx_count = 0; static uint8_t tx_buf[262] TU_ATTR_ALIGNED(4); static uint32_t tx_count; +#define CFG_TUC_STM32_DMA_RX { DMA1_Channel1 } +//#define CFG_TUC_STM32_DMA_TX { DMA1_Channel2 } + +#ifdef CFG_TUC_STM32_DMA_RX +static DMA_Channel_TypeDef* dma_rx_arr[TUP_TYPEC_RHPORTS_NUM] = CFG_TUC_STM32_DMA_RX; + +TU_ATTR_ALWAYS_INLINE static inline +void dma_rx_start(uint8_t rhport) +{ + DMA_Channel_TypeDef* dma_rx_ch = dma_rx_arr[rhport]; + + dma_rx_ch->CMAR = (uint32_t) rx_buf; + dma_rx_ch->CNDTR = sizeof(rx_buf); + dma_rx_ch->CCR |= DMA_CCR_EN; +} +#endif + +#ifdef CFG_TUC_STM32_DMA_TX +static DMA_Channel_TypeDef* dma_tx_arr[TUP_TYPEC_RHPORTS_NUM] = CFG_TUC_STM32_DMA_TX; +#endif + //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ +#include "stm32g4xx_ll_dma.h" bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type) { (void) rhport; +#ifdef CFG_TUC_STM32_DMA_RX + // Init DMA + DMA_Channel_TypeDef* dma_rx_ch = dma_rx_arr[rhport]; + + // Peripheral -> Memory, Memory inc, 8-bit, High priority + dma_rx_ch->CCR = DMA_CCR_MINC | DMA_CCR_PL_1; + dma_rx_ch->CPAR = (uint32_t) &UCPD1->RXDR; + + LL_DMA_SetPeriphRequest(DMA1, LL_DMA_CHANNEL_1, LL_DMAMUX_REQ_UCPD1_RX); +#endif + // Initialization phase: CFG1 UCPD1->CFG1 = (0x0d << UCPD_CFG1_HBITCLKDIV_Pos) | (0x10 << UCPD_CFG1_IFRGAP_Pos) | (0x07 << UCPD_CFG1_TRANSWIN_Pos) | (0x01 << UCPD_CFG1_PSC_UCPDCLK_Pos) | (0x1f << UCPD_CFG1_RXORDSETEN_Pos) | @@ -77,7 +111,7 @@ bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type) { // General programming sequence (with UCPD configured then enabled) if (port_type == TUSB_TYPEC_PORT_SNK) { // Enable both CC Phy - UCPD1->CR = (0x01 << UCPD_CR_ANAMODE_Pos) | (0x03 << UCPD_CR_CCENABLE_Pos); + UCPD1->CR = (0x01 << UCPD_CR_ANAMODE_Pos) | UCPD_CR_CCENABLE_0 | UCPD_CR_CCENABLE_1; // Read Voltage State on CC1 & CC2 fore initial state uint32_t vstate_cc[2]; @@ -135,30 +169,48 @@ void tcd_int_handler(uint8_t rhport) { TU_LOG1("VState CC1 = %u, CC2 = %u\n", vstate_cc[0], vstate_cc[1]); uint32_t cr = UCPD1->CR; + uint32_t cfg1 = UCPD1->CFG1; // TODO only support SNK for now, required highest voltage for now + // Enable PHY on correct CC and disable Rd on other CC if ((sr & UCPD_SR_TYPECEVT1) && (vstate_cc[0] == 3)) { TU_LOG1("Attach CC1\n"); - cr &= ~UCPD_CR_PHYCCSEL; - cr |= UCPD_CR_PHYRXEN; + + cr &= ~(UCPD_CR_PHYCCSEL | UCPD_CR_CCENABLE); + cr |= UCPD_CR_PHYRXEN | UCPD_CR_CCENABLE_0; } else if ((sr & UCPD_SR_TYPECEVT2) && (vstate_cc[1] == 3)) { TU_LOG1("Attach CC2\n"); - cr |= UCPD_CR_PHYCCSEL; - cr |= UCPD_CR_PHYRXEN; + cr &= ~UCPD_CR_CCENABLE; + cr |= (UCPD_CR_PHYCCSEL | UCPD_CR_PHYRXEN | UCPD_CR_CCENABLE_1); } else { TU_LOG1("Detach\n"); cr &= ~UCPD_CR_PHYRXEN; + cr |= UCPD_CR_CCENABLE_0 | UCPD_CR_CCENABLE_1; } if (cr & UCPD_CR_PHYRXEN) { // Enable Interrupt - UCPD1->IMR |= UCPD_IMR_TXISIE | UCPD_IMR_TXMSGDISCIE | UCPD_IMR_TXMSGSENTIE | UCPD_IMR_TXMSGABTIE | UCPD_IMR_TXUNDIE | - UCPD_IMR_RXNEIE | UCPD_IMR_RXORDDETIE | UCPD_IMR_RXHRSTDETIE | UCPD_IMR_RXOVRIE | - UCPD_IMR_RXMSGENDIE | UCPD_IMR_HRSTDISCIE | UCPD_IMR_HRSTSENTIE; + uint32_t imr = UCPD1->IMR; + imr |= UCPD_IMR_TXMSGDISCIE | UCPD_IMR_TXMSGSENTIE | UCPD_IMR_TXMSGABTIE | UCPD_IMR_TXUNDIE | + UCPD_IMR_RXHRSTDETIE | UCPD_IMR_RXOVRIE | UCPD_IMR_RXMSGENDIE | UCPD_IMR_RXORDDETIE | + UCPD_IMR_HRSTDISCIE | UCPD_IMR_HRSTSENTIE | UCPD_IMR_FRSEVTIE; + + #ifdef CFG_TUC_STM32_DMA_RX + cfg1 |= UCPD_CFG1_RXDMAEN; + dma_rx_start(rhport); + #else + imr |= UCPD_IMR_RXNEIE | UCPD_IMR_RXORDDETIE; + #endif + + #ifndef CFG_TUC_STM32_DMA_TX + imr |= UCPD_IMR_TXISIE; + #endif + + UCPD1->IMR = imr; } - // Enable PD RX UCPD1->CR = cr; + UCPD1->CFG1 = cfg1; // ack UCPD1->ICR = UCPD_ICR_TYPECEVT1CF | UCPD_ICR_TYPECEVT2CF; @@ -176,6 +228,7 @@ void tcd_int_handler(uint8_t rhport) { UCPD1->ICR = UCPD_ICR_RXORDDETCF; } +#ifndef CFG_TUC_STM32_DMA_RX if (sr & UCPD_SR_RXNE) { // TODO DMA later do { @@ -184,8 +237,9 @@ void tcd_int_handler(uint8_t rhport) { // no ack needed } +#endif - // End of message + // Received full message if (sr & UCPD_SR_RXMSGEND) { // Skip if CRC failed @@ -213,13 +267,17 @@ void tcd_int_handler(uint8_t rhport) { // notify stack after good crc ? } + #ifdef CFG_TUC_STM32_DMA_RX + // prepare next receive + dma_rx_start(rhport); + #endif + // ack UCPD1->ICR = UCPD_ICR_RXMSGENDCF; } if (sr & UCPD_SR_RXOVR) { TU_LOG1("RXOVR\n"); - TU_LOG1_HEX(rx_count); // ack UCPD1->ICR = UCPD_ICR_RXOVRCF; } -- cgit v1.3.1 From 8181d470e5bbb01f873d8fa11e8e1293cb76703f Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 8 Jun 2023 18:55:54 +0700 Subject: enable DMA for both pd rx, tx --- src/portable/st/typec/typec_stm32.c | 207 +++++++++++++++++++----------------- 1 file changed, 108 insertions(+), 99 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index c96dd0902..a898cda47 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -31,7 +31,7 @@ #if CFG_TUSB_MCU == OPT_MCU_STM32G4 #include "stm32g4xx.h" - #include "stm32g4xx_hal_dma.h" + #include "stm32g4xx_ll_dma.h" // for UCLP REQID #else #error "Unsupported STM32 family" #endif @@ -40,6 +40,12 @@ // //--------------------------------------------------------------------+ +enum { + IMR_ATTACHED = UCPD_IMR_TXMSGDISCIE | UCPD_IMR_TXMSGSENTIE | UCPD_IMR_TXMSGABTIE | UCPD_IMR_TXUNDIE | + UCPD_IMR_RXHRSTDETIE | UCPD_IMR_RXOVRIE | UCPD_IMR_RXMSGENDIE | UCPD_IMR_RXORDDETIE | + UCPD_IMR_HRSTDISCIE | UCPD_IMR_HRSTSENTIE | UCPD_IMR_FRSEVTIE +}; + #define PHY_SYNC1 0x18u #define PHY_SYNC2 0x11u #define PHY_SYNC3 0x06u @@ -57,55 +63,101 @@ static uint8_t rx_buf[262] TU_ATTR_ALIGNED(4); -static uint32_t rx_count = 0; - static uint8_t tx_buf[262] TU_ATTR_ALIGNED(4); -static uint32_t tx_count; +static uint32_t tx_index; -#define CFG_TUC_STM32_DMA_RX { DMA1_Channel1 } -//#define CFG_TUC_STM32_DMA_TX { DMA1_Channel2 } +// address of DMA channel rx, tx for each port +#define CFG_TUC_STM32_DMA { { DMA1_Channel1_BASE, DMA1_Channel2_BASE } } -#ifdef CFG_TUC_STM32_DMA_RX -static DMA_Channel_TypeDef* dma_rx_arr[TUP_TYPEC_RHPORTS_NUM] = CFG_TUC_STM32_DMA_RX; +//--------------------------------------------------------------------+ +// DMA +//--------------------------------------------------------------------+ -TU_ATTR_ALWAYS_INLINE static inline -void dma_rx_start(uint8_t rhport) -{ - DMA_Channel_TypeDef* dma_rx_ch = dma_rx_arr[rhport]; +static const uint32_t dma_addr_arr[TUP_TYPEC_RHPORTS_NUM][2] = CFG_TUC_STM32_DMA; - dma_rx_ch->CMAR = (uint32_t) rx_buf; - dma_rx_ch->CNDTR = sizeof(rx_buf); - dma_rx_ch->CCR |= DMA_CCR_EN; +TU_ATTR_ALWAYS_INLINE static inline uint32_t dma_get_addr(uint8_t rhport, bool is_rx) { + return dma_addr_arr[rhport][is_rx ? 0 : 1]; } -#endif -#ifdef CFG_TUC_STM32_DMA_TX -static DMA_Channel_TypeDef* dma_tx_arr[TUP_TYPEC_RHPORTS_NUM] = CFG_TUC_STM32_DMA_TX; -#endif +static void dma_init(uint8_t rhport, bool is_rx) { + uint32_t dma_addr = dma_get_addr(rhport, is_rx); + DMA_Channel_TypeDef* dma_ch = (DMA_Channel_TypeDef*) dma_addr; + uint32_t req_id; + + if (is_rx) { + // Peripheral -> Memory, Memory inc, 8-bit, High priority + dma_ch->CCR = DMA_CCR_MINC | DMA_CCR_PL_1; + dma_ch->CPAR = (uint32_t) &UCPD1->RXDR; + + req_id = LL_DMAMUX_REQ_UCPD1_RX; + } else { + // Memory -> Peripheral, Memory inc, 8-bit, High priority + dma_ch->CCR = DMA_CCR_MINC | DMA_CCR_PL_1 | DMA_CCR_DIR; + dma_ch->CPAR = (uint32_t) &UCPD1->TXDR; + + req_id = LL_DMAMUX_REQ_UCPD1_TX; + } + + // find and set up mux channel TODO support mcu with multiple DMAMUXs + enum { + CH_DIFF = DMA1_Channel2_BASE - DMA1_Channel1_BASE + }; + uint32_t mux_ch_num; + + #ifdef DMA2_BASE + if (dma_addr > DMA2_BASE) { + mux_ch_num = 8 * ((dma_addr - DMA2_Channel1_BASE) / CH_DIFF); + } else + #endif + { + mux_ch_num = (dma_addr - DMA1_Channel1_BASE) / CH_DIFF; + } + + DMAMUX_Channel_TypeDef* mux_ch = DMAMUX1_Channel0 + mux_ch_num; + + uint32_t mux_ccr = mux_ch->CCR & ~(DMAMUX_CxCR_DMAREQ_ID); + mux_ccr |= req_id; + mux_ch->CCR = mux_ccr; +} + +TU_ATTR_ALWAYS_INLINE static inline void dma_start(uint8_t rhport, bool is_rx, void const* buf, uint16_t len) { + DMA_Channel_TypeDef* dma_ch = (DMA_Channel_TypeDef*) dma_get_addr(rhport, is_rx); + + dma_ch->CMAR = (uint32_t) buf; + dma_ch->CNDTR = len; + dma_ch->CCR |= DMA_CCR_EN; +} + +TU_ATTR_ALWAYS_INLINE static inline void dma_stop(uint8_t rhport, bool is_rx) { + DMA_Channel_TypeDef* dma_ch = (DMA_Channel_TypeDef*) dma_get_addr(rhport, is_rx); + dma_ch->CCR &= ~DMA_CCR_EN; +} + +TU_ATTR_ALWAYS_INLINE static inline void dma_rx_start(uint8_t rhport) { + dma_start(rhport, true, rx_buf, sizeof(rx_buf)); +} + +TU_ATTR_ALWAYS_INLINE static inline void dma_tx_start(uint8_t rhport, void const* buf, uint16_t len) { + UCPD1->TX_ORDSET = PHY_ORDERED_SET_SOP; + UCPD1->TX_PAYSZ = len; + dma_start(rhport, false, buf, len); +} //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ -#include "stm32g4xx_ll_dma.h" + bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type) { (void) rhport; -#ifdef CFG_TUC_STM32_DMA_RX - // Init DMA - DMA_Channel_TypeDef* dma_rx_ch = dma_rx_arr[rhport]; - - // Peripheral -> Memory, Memory inc, 8-bit, High priority - dma_rx_ch->CCR = DMA_CCR_MINC | DMA_CCR_PL_1; - dma_rx_ch->CPAR = (uint32_t) &UCPD1->RXDR; - - LL_DMA_SetPeriphRequest(DMA1, LL_DMA_CHANNEL_1, LL_DMAMUX_REQ_UCPD1_RX); -#endif + // Init DMA for RX, TX + dma_init(rhport, true); + dma_init(rhport, false); // Initialization phase: CFG1 UCPD1->CFG1 = (0x0d << UCPD_CFG1_HBITCLKDIV_Pos) | (0x10 << UCPD_CFG1_IFRGAP_Pos) | (0x07 << UCPD_CFG1_TRANSWIN_Pos) | - (0x01 << UCPD_CFG1_PSC_UCPDCLK_Pos) | (0x1f << UCPD_CFG1_RXORDSETEN_Pos) | - (0 << UCPD_CFG1_TXDMAEN_Pos) | (0 << UCPD_CFG1_RXDMAEN_Pos); + (0x01 << UCPD_CFG1_PSC_UCPDCLK_Pos) | (0x1f << UCPD_CFG1_RXORDSETEN_Pos); UCPD1->CFG1 |= UCPD_CFG1_UCPDEN; // General programming sequence (with UCPD configured then enabled) @@ -118,8 +170,7 @@ bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type) { vstate_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; vstate_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; - TU_LOG1_INT(vstate_cc[0]); - TU_LOG1_INT(vstate_cc[1]); + TU_LOG1("Initial VState CC1 = %u, CC2 = %u\r\n", vstate_cc[0], vstate_cc[1]); // Enable CC1 & CC2 Interrupt UCPD1->IMR = UCPD_IMR_TYPECEVT1IE | UCPD_IMR_TYPECEVT2IE; @@ -142,7 +193,8 @@ void tcd_int_disable(uint8_t rhport) { bool tcd_rx_start(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes) { (void) rhport; - + (void) buffer; + (void) total_bytes; return true; } @@ -159,8 +211,6 @@ void tcd_int_handler(uint8_t rhport) { uint32_t sr = UCPD1->SR; sr &= UCPD1->IMR; -// TU_LOG1("UCPD1_IRQHandler: sr = 0x%08X\n", sr); - if (sr & (UCPD_SR_TYPECEVT1 | UCPD_SR_TYPECEVT2)) { uint32_t vstate_cc[2]; vstate_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; @@ -169,7 +219,6 @@ void tcd_int_handler(uint8_t rhport) { TU_LOG1("VState CC1 = %u, CC2 = %u\n", vstate_cc[0], vstate_cc[1]); uint32_t cr = UCPD1->CR; - uint32_t cfg1 = UCPD1->CFG1; // TODO only support SNK for now, required highest voltage for now // Enable PHY on correct CC and disable Rd on other CC @@ -189,28 +238,18 @@ void tcd_int_handler(uint8_t rhport) { } if (cr & UCPD_CR_PHYRXEN) { - // Enable Interrupt - uint32_t imr = UCPD1->IMR; - imr |= UCPD_IMR_TXMSGDISCIE | UCPD_IMR_TXMSGSENTIE | UCPD_IMR_TXMSGABTIE | UCPD_IMR_TXUNDIE | - UCPD_IMR_RXHRSTDETIE | UCPD_IMR_RXOVRIE | UCPD_IMR_RXMSGENDIE | UCPD_IMR_RXORDDETIE | - UCPD_IMR_HRSTDISCIE | UCPD_IMR_HRSTSENTIE | UCPD_IMR_FRSEVTIE; - - #ifdef CFG_TUC_STM32_DMA_RX - cfg1 |= UCPD_CFG1_RXDMAEN; - dma_rx_start(rhport); - #else - imr |= UCPD_IMR_RXNEIE | UCPD_IMR_RXORDDETIE; - #endif + // Attached + UCPD1->IMR |= IMR_ATTACHED; + UCPD1->CFG1 |= UCPD_CFG1_RXDMAEN | UCPD_CFG1_TXDMAEN; - #ifndef CFG_TUC_STM32_DMA_TX - imr |= UCPD_IMR_TXISIE; - #endif - - UCPD1->IMR = imr; + dma_rx_start(rhport); + }else { + // Detached + UCPD1->CFG1 &= ~(UCPD_CFG1_RXDMAEN | UCPD_CFG1_TXDMAEN); + UCPD1->IMR &= ~IMR_ATTACHED; } UCPD1->CR = cr; - UCPD1->CFG1 = cfg1; // ack UCPD1->ICR = UCPD_ICR_TYPECEVT1CF | UCPD_ICR_TYPECEVT2CF; @@ -221,27 +260,15 @@ void tcd_int_handler(uint8_t rhport) { // SOP: Start of Packet. // UCPD1->RX_ORDSET & UCPD_RX_ORDSET_RXORDSET_Msk; - // reset count when received SOP - rx_count = 0; - // ack UCPD1->ICR = UCPD_ICR_RXORDDETCF; } -#ifndef CFG_TUC_STM32_DMA_RX - if (sr & UCPD_SR_RXNE) { - // TODO DMA later - do { - rx_buf[rx_count++] = UCPD1->RXDR; - } while (UCPD1->SR & UCPD_SR_RXNE); - - // no ack needed - } -#endif - // Received full message if (sr & UCPD_SR_RXMSGEND) { + dma_stop(rhport, true); + // Skip if CRC failed if (!(sr & UCPD_SR_RXERR)) { uint32_t payload_size = UCPD1->RX_PAYSZ; @@ -251,26 +278,23 @@ void tcd_int_handler(uint8_t rhport) { (*(tusb_pd_header_t*) tx_buf) = (tusb_pd_header_t) { .msg_type = TUSB_PD_CTRL_GOOD_CRC, .data_role = 0, // UFP - .specs_rev = TUSB_PD_REV30, + .specs_rev = TUSB_PD_REV20, .power_role = 0, // Sink .msg_id = rx_header->msg_id, .n_data_obj = 0, .extended = 0 }; - tx_count = 0; // response with good crc - UCPD1->TX_ORDSET = PHY_ORDERED_SET_SOP; - UCPD1->TX_PAYSZ = 2; - UCPD1->CR |= UCPD_CR_TXSEND; // will trigger TXIS interrupt + dma_tx_start(rhport, tx_buf, 2); + + UCPD1->CR |= UCPD_CR_TXSEND; - // notify stack after good crc ? + // notify stack } - #ifdef CFG_TUC_STM32_DMA_RX // prepare next receive dma_rx_start(rhport); - #endif // ack UCPD1->ICR = UCPD_ICR_RXMSGENDCF; @@ -283,34 +307,19 @@ void tcd_int_handler(uint8_t rhport) { } //------------- TX -------------// - if (sr & UCPD_SR_TXIS) { - // TU_LOG1("TXIS\n"); - - // TODO DMA later - do { - UCPD1->TXDR = tx_buf[tx_count++]; - } while (UCPD1->SR & UCPD_SR_TXIS); - - // no ack needed - } - if (sr & UCPD_SR_TXMSGSENT) { // all byte sent - TU_LOG1("TXMSGSENT\n"); + dma_stop(rhport, false); // ack UCPD1->ICR = UCPD_ICR_TXMSGSENTCF; } -// if (sr & UCPD_SR_RXNE) { -// uint8_t data = UCPD1->RXDR; -// pd_rx_buf[pd_rx_count++] = data; -// TU_LOG1_HEX(data); -// } - -// else { -// TU_LOG_LOCATION(); -// } + if (sr & (UCPD_SR_TXMSGDISC | UCPD_SR_TXMSGABT | UCPD_SR_TXUND)) { + TU_LOG1("TX Error\n"); + dma_stop(rhport, false); + UCPD1->ICR = UCPD_SR_TXMSGDISC | UCPD_SR_TXMSGABT | UCPD_SR_TXUND; + } } #endif -- cgit v1.3.1 From 912802456b568e4b666a9205c3799da79f87ef69 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 9 Jun 2023 18:15:28 +0700 Subject: move protocol message to stack, disable battery in PWR's CR3 there is still issue with CC1/CC2 pull down resistor and vstate is not correct. --- hw/bsp/stm32g4/family.c | 8 +-- src/device/dcd.h | 1 + src/portable/st/typec/typec_stm32.c | 113 ++++++++++++++++++------------------ src/typec/tcd.h | 52 +++++++++++++++++ src/typec/utcd.c | 61 ++++++++++++++----- src/typec/utcd.h | 2 +- 6 files changed, 162 insertions(+), 75 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/stm32g4/family.c b/hw/bsp/stm32g4/family.c index 5fa6e3dbb..d77183357 100644 --- a/hw/bsp/stm32g4/family.c +++ b/hw/bsp/stm32g4/family.c @@ -145,13 +145,13 @@ void board_init(void) #if 1 // USB PD // Default CC1/CC2 is PB4/PB6 - /* PWR register access (for disabling dead battery feature) */ - LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_PWR); - LL_AHB1_GRP1_EnableClock(LL_AHB1_GRP1_PERIPH_CRC); + // Enable pwr for disabling dead battery feature in Power's CR3 + __HAL_RCC_PWR_CLK_ENABLE(); + __HAL_RCC_CRC_CLK_ENABLE(); __HAL_RCC_UCPD1_CLK_ENABLE(); - // Enable DMA clock + // Enable DMA for USB PD __HAL_RCC_DMAMUX1_CLK_ENABLE(); __HAL_RCC_DMA1_CLK_ENABLE(); #endif diff --git a/src/device/dcd.h b/src/device/dcd.h index f82b8633d..4e9cfd5d5 100644 --- a/src/device/dcd.h +++ b/src/device/dcd.h @@ -189,6 +189,7 @@ TU_ATTR_WEAK bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t l // Configure and enable an ISO endpoint according to descriptor TU_ATTR_WEAK bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc); + //--------------------------------------------------------------------+ // Event API (implemented by stack) //--------------------------------------------------------------------+ diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index a898cda47..1dba54492 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -31,7 +31,7 @@ #if CFG_TUSB_MCU == OPT_MCU_STM32G4 #include "stm32g4xx.h" - #include "stm32g4xx_ll_dma.h" // for UCLP REQID + #include "stm32g4xx_ll_dma.h" // for UCPD REQID #else #error "Unsupported STM32 family" #endif @@ -62,9 +62,17 @@ enum { #define PHY_ORDERED_SET_SOP_PP_DEBUG (PHY_SYNC1 | (PHY_RST2<<5u) | (PHY_SYNC3<<10u) | (PHY_SYNC2<<15u)) // SOP'' Debug Ordered set coding -static uint8_t rx_buf[262] TU_ATTR_ALIGNED(4); -static uint8_t tx_buf[262] TU_ATTR_ALIGNED(4); -static uint32_t tx_index; +static uint8_t const* _rx_buf; + +static tusb_pd_header_t _good_crc = { + .msg_type = TUSB_PD_CTRL_GOOD_CRC, + .data_role = 0, // UFP + .specs_rev = TUSB_PD_REV20, + .power_role = 0, // Sink + .msg_id = 0, + .n_data_obj = 0, + .extended = 0 +}; // address of DMA channel rx, tx for each port #define CFG_TUC_STM32_DMA { { DMA1_Channel1_BASE, DMA1_Channel2_BASE } } @@ -73,10 +81,10 @@ static uint32_t tx_index; // DMA //--------------------------------------------------------------------+ -static const uint32_t dma_addr_arr[TUP_TYPEC_RHPORTS_NUM][2] = CFG_TUC_STM32_DMA; +static const uint32_t _dma_addr_arr[TUP_TYPEC_RHPORTS_NUM][2] = CFG_TUC_STM32_DMA; TU_ATTR_ALWAYS_INLINE static inline uint32_t dma_get_addr(uint8_t rhport, bool is_rx) { - return dma_addr_arr[rhport][is_rx ? 0 : 1]; + return _dma_addr_arr[rhport][is_rx ? 0 : 1]; } static void dma_init(uint8_t rhport, bool is_rx) { @@ -133,10 +141,6 @@ TU_ATTR_ALWAYS_INLINE static inline void dma_stop(uint8_t rhport, bool is_rx) { dma_ch->CCR &= ~DMA_CCR_EN; } -TU_ATTR_ALWAYS_INLINE static inline void dma_rx_start(uint8_t rhport) { - dma_start(rhport, true, rx_buf, sizeof(rx_buf)); -} - TU_ATTR_ALWAYS_INLINE static inline void dma_tx_start(uint8_t rhport, void const* buf, uint16_t len) { UCPD1->TX_ORDSET = PHY_ORDERED_SET_SOP; UCPD1->TX_PAYSZ = len; @@ -147,7 +151,6 @@ TU_ATTR_ALWAYS_INLINE static inline void dma_tx_start(uint8_t rhport, void const // //--------------------------------------------------------------------+ - bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type) { (void) rhport; @@ -155,27 +158,30 @@ bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type) { dma_init(rhport, true); dma_init(rhport, false); - // Initialization phase: CFG1 + // Initialization phase: CFG1, detect all SOPs UCPD1->CFG1 = (0x0d << UCPD_CFG1_HBITCLKDIV_Pos) | (0x10 << UCPD_CFG1_IFRGAP_Pos) | (0x07 << UCPD_CFG1_TRANSWIN_Pos) | (0x01 << UCPD_CFG1_PSC_UCPDCLK_Pos) | (0x1f << UCPD_CFG1_RXORDSETEN_Pos); UCPD1->CFG1 |= UCPD_CFG1_UCPDEN; // General programming sequence (with UCPD configured then enabled) if (port_type == TUSB_TYPEC_PORT_SNK) { - // Enable both CC Phy - UCPD1->CR = (0x01 << UCPD_CR_ANAMODE_Pos) | UCPD_CR_CCENABLE_0 | UCPD_CR_CCENABLE_1; + // Set analog mode enable both CC Phy + UCPD1->CR = (0x01 << UCPD_CR_ANAMODE_Pos) | (UCPD_CR_CCENABLE_0 | UCPD_CR_CCENABLE_1); // Read Voltage State on CC1 & CC2 fore initial state - uint32_t vstate_cc[2]; - vstate_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; - vstate_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; + uint32_t v_cc[2]; + v_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; + v_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; - TU_LOG1("Initial VState CC1 = %u, CC2 = %u\r\n", vstate_cc[0], vstate_cc[1]); + TU_LOG1("Initial VState CC1 = %u, CC2 = %u\r\n", v_cc[0], v_cc[1]); // Enable CC1 & CC2 Interrupt UCPD1->IMR = UCPD_IMR_TYPECEVT1IE | UCPD_IMR_TYPECEVT2IE; } + // Disable dead battery in PWR's CR3 + PWR->CR3 |= PWR_CR3_UCPD_DBDIS; + return true; } @@ -192,9 +198,8 @@ void tcd_int_disable(uint8_t rhport) { } bool tcd_rx_start(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes) { - (void) rhport; - (void) buffer; - (void) total_bytes; + _rx_buf = buffer; + dma_start(rhport, true, buffer, total_bytes); return true; } @@ -212,27 +217,28 @@ void tcd_int_handler(uint8_t rhport) { sr &= UCPD1->IMR; if (sr & (UCPD_SR_TYPECEVT1 | UCPD_SR_TYPECEVT2)) { - uint32_t vstate_cc[2]; - vstate_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; - vstate_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; + uint32_t v_cc[2]; + v_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; + v_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; - TU_LOG1("VState CC1 = %u, CC2 = %u\n", vstate_cc[0], vstate_cc[1]); + TU_LOG3("VState CC1 = %u, CC2 = %u\n", v_cc[0], v_cc[1]); uint32_t cr = UCPD1->CR; // TODO only support SNK for now, required highest voltage for now - // Enable PHY on correct CC and disable Rd on other CC - if ((sr & UCPD_SR_TYPECEVT1) && (vstate_cc[0] == 3)) { - TU_LOG1("Attach CC1\n"); - + // Enable PHY on active CC and disable Rd on other CC + // FIXME somehow CC2 is vstate is not correct, always 1 even not attached. + // on DPOW1 board, it is connected to PA10 (USBPD_DBCC2), we probably miss something. + if ((sr & UCPD_SR_TYPECEVT1) && (v_cc[0] == 3)) { + TU_LOG3("Attach CC1\n"); cr &= ~(UCPD_CR_PHYCCSEL | UCPD_CR_CCENABLE); cr |= UCPD_CR_PHYRXEN | UCPD_CR_CCENABLE_0; - } else if ((sr & UCPD_SR_TYPECEVT2) && (vstate_cc[1] == 3)) { - TU_LOG1("Attach CC2\n"); + } else if ((sr & UCPD_SR_TYPECEVT2) && (v_cc[1] == 3)) { + TU_LOG3("Attach CC2\n"); cr &= ~UCPD_CR_CCENABLE; cr |= (UCPD_CR_PHYCCSEL | UCPD_CR_PHYRXEN | UCPD_CR_CCENABLE_1); } else { - TU_LOG1("Detach\n"); + TU_LOG3("Detach\n"); cr &= ~UCPD_CR_PHYRXEN; cr |= UCPD_CR_CCENABLE_0 | UCPD_CR_CCENABLE_1; } @@ -241,14 +247,15 @@ void tcd_int_handler(uint8_t rhport) { // Attached UCPD1->IMR |= IMR_ATTACHED; UCPD1->CFG1 |= UCPD_CFG1_RXDMAEN | UCPD_CFG1_TXDMAEN; - - dma_rx_start(rhport); }else { // Detached UCPD1->CFG1 &= ~(UCPD_CFG1_RXDMAEN | UCPD_CFG1_TXDMAEN); UCPD1->IMR &= ~IMR_ATTACHED; } + // notify stack + tcd_event_cc_changed(rhport, v_cc[0], v_cc[1], true); + UCPD1->CR = cr; // ack @@ -258,6 +265,7 @@ void tcd_int_handler(uint8_t rhport) { //------------- RX -------------// if (sr & UCPD_SR_RXORDDET) { // SOP: Start of Packet. + TU_LOG3("SOP\n"); // UCPD1->RX_ORDSET & UCPD_RX_ORDSET_RXORDSET_Msk; // ack @@ -266,48 +274,39 @@ void tcd_int_handler(uint8_t rhport) { // Received full message if (sr & UCPD_SR_RXMSGEND) { - + TU_LOG3("RX MSG END\n"); dma_stop(rhport, true); - // Skip if CRC failed - if (!(sr & UCPD_SR_RXERR)) { - uint32_t payload_size = UCPD1->RX_PAYSZ; - // TU_LOG1("RXMSGEND: payload_size = %u, rx count = %u\n", payload_size, pd_rx_count); - - tusb_pd_header_t const* rx_header = (tusb_pd_header_t const*) rx_buf; - (*(tusb_pd_header_t*) tx_buf) = (tusb_pd_header_t) { - .msg_type = TUSB_PD_CTRL_GOOD_CRC, - .data_role = 0, // UFP - .specs_rev = TUSB_PD_REV20, - .power_role = 0, // Sink - .msg_id = rx_header->msg_id, - .n_data_obj = 0, - .extended = 0 - }; + uint8_t result; + if (!(sr & UCPD_SR_RXERR)) { // response with good crc - dma_tx_start(rhport, tx_buf, 2); - + _good_crc.msg_id = ((tusb_pd_header_t const*) _rx_buf)->msg_id; + dma_tx_start(rhport, &_good_crc, 2); UCPD1->CR |= UCPD_CR_TXSEND; - // notify stack + result = XFER_RESULT_SUCCESS; + }else { + // CRC failed + result = XFER_RESULT_FAILED; } - // prepare next receive - dma_rx_start(rhport); + // notify stack + tcd_event_rx_complete(rhport, UCPD1->RX_PAYSZ, result, true); // ack UCPD1->ICR = UCPD_ICR_RXMSGENDCF; } if (sr & UCPD_SR_RXOVR) { - TU_LOG1("RXOVR\n"); + TU_LOG3("RXOVR\n"); // ack UCPD1->ICR = UCPD_ICR_RXOVRCF; } //------------- TX -------------// if (sr & UCPD_SR_TXMSGSENT) { + TU_LOG3("TX MSG SENT\n"); // all byte sent dma_stop(rhport, false); @@ -316,7 +315,7 @@ void tcd_int_handler(uint8_t rhport) { } if (sr & (UCPD_SR_TXMSGDISC | UCPD_SR_TXMSGABT | UCPD_SR_TXUND)) { - TU_LOG1("TX Error\n"); + TU_LOG3("TX Error\n"); dma_stop(rhport, false); UCPD1->ICR = UCPD_SR_TXMSGDISC | UCPD_SR_TXMSGABT | UCPD_SR_TXUND; } diff --git a/src/typec/tcd.h b/src/typec/tcd.h index e823bf8d7..41dceaa74 100644 --- a/src/typec/tcd.h +++ b/src/typec/tcd.h @@ -38,10 +38,28 @@ extern "C" { //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ + +enum { + TCD_EVENT_INVALID = 0, + TCD_EVENT_CC_CHANGED, + TCD_EVENT_RX_COMPLETE, +}; + + typedef struct { uint8_t rhport; uint8_t event_id; + union { + struct { + uint8_t cc_state[2]; + } cc_changed; + + struct { + uint16_t xferred_bytes; + uint8_t result; + } rx_complete; + }; } tcd_event_t;; @@ -68,4 +86,38 @@ void tcd_int_handler(uint8_t rhport); bool tcd_rx_start(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes); bool tcd_tx_start(uint8_t rhport, uint8_t const* buffer, uint16_t total_bytes); +//--------------------------------------------------------------------+ +// Event API (implemented by stack) +// Called by TCD to notify stack +//--------------------------------------------------------------------+ + +extern void tcd_event_handler(tcd_event_t const * event, bool in_isr); + +TU_ATTR_ALWAYS_INLINE static inline +void tcd_event_cc_changed(uint8_t rhport, uint8_t cc1, uint8_t cc2, bool in_isr) { + tcd_event_t event = { + .rhport = rhport, + .event_id = TCD_EVENT_CC_CHANGED, + .cc_changed = { + .cc_state = {cc1, cc2 } + } + }; + + tcd_event_handler(&event, in_isr); +} + +TU_ATTR_ALWAYS_INLINE static inline +void tcd_event_rx_complete(uint8_t rhport, uint16_t xferred_bytes, uint8_t result, bool in_isr) { + tcd_event_t event = { + .rhport = rhport, + .event_id = TCD_EVENT_RX_COMPLETE, + .rx_complete = { + .xferred_bytes = xferred_bytes, + .result = result + } + }; + + tcd_event_handler(&event, in_isr); +} + #endif diff --git a/src/typec/utcd.c b/src/typec/utcd.c index b5f9965fe..fb69b01e8 100644 --- a/src/typec/utcd.c +++ b/src/typec/utcd.c @@ -42,35 +42,38 @@ // Event queue // utcd_int_set() is used as mutex in OS NONE config void utcd_int_set(bool enabled); -OSAL_QUEUE_DEF(utcd_int_set, utcd_qdef, CFG_TUC_TASK_QUEUE_SZ, tcd_event_t); -tu_static osal_queue_t utcd_q; +OSAL_QUEUE_DEF(utcd_int_set, _utcd_qdef, CFG_TUC_TASK_QUEUE_SZ, tcd_event_t); +tu_static osal_queue_t _utcd_q; // if stack is initialized -static bool utcd_inited = false; +static bool _utcd_inited = false; // if port is initialized -static bool port_inited[TUP_TYPEC_RHPORTS_NUM]; +static bool _port_inited[TUP_TYPEC_RHPORTS_NUM]; + +// Max possible PD size is 262 bytes +static uint8_t _rx_buf[262] TU_ATTR_ALIGNED(4); //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ bool tuc_inited(uint8_t rhport) { - return utcd_inited && port_inited[rhport]; + return _utcd_inited && _port_inited[rhport]; } bool tuc_init(uint8_t rhport, tusb_typec_port_type_t port_type) { // Initialize stack - if (!utcd_inited) { - tu_memclr(port_inited, sizeof(port_inited)); + if (!_utcd_inited) { + tu_memclr(_port_inited, sizeof(_port_inited)); - utcd_q = osal_queue_create(&utcd_qdef); - TU_ASSERT(utcd_q != NULL); + _utcd_q = osal_queue_create(&_utcd_qdef); + TU_ASSERT(_utcd_q != NULL); - utcd_inited = true; + _utcd_inited = true; } // skip if port already initialized - if ( port_inited[rhport] ) { + if ( _port_inited[rhport] ) { return true; } @@ -79,10 +82,42 @@ bool tuc_init(uint8_t rhport, tusb_typec_port_type_t port_type) { TU_ASSERT(tcd_init(rhport, port_type)); tcd_int_enable(rhport); - port_inited[rhport] = true; + _port_inited[rhport] = true; return true; } +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +//bool parse_message(uint8_t const * data, uint16_t len, pd_msg_t * msg) { +// // TODO +// (void) data; +// (void) len; +// (void) msg; +// return false; +//} + +void tcd_event_handler(tcd_event_t const * event, bool in_isr) { + (void) in_isr; + switch(event->event_id) { + case TCD_EVENT_CC_CHANGED: + if (event->cc_changed.cc_state[0] || event->cc_changed.cc_state[1]) { + // Attach + tcd_rx_start(event->rhport, _rx_buf, sizeof(_rx_buf)); + }else { + // Detach + } + break; + + case TCD_EVENT_RX_COMPLETE: + // TODO process message here in ISR, move to thread later + + // start new rx + tcd_rx_start(event->rhport, _rx_buf, sizeof(_rx_buf)); + break; + } +} //--------------------------------------------------------------------+ // @@ -90,7 +125,7 @@ bool tuc_init(uint8_t rhport, tusb_typec_port_type_t port_type) { void utcd_int_set(bool enabled) { // Disable all controllers since they shared the same event queue for (uint8_t p = 0; p < TUP_TYPEC_RHPORTS_NUM; p++) { - if ( port_inited[p] ) { + if ( _port_inited[p] ) { if (enabled) { tcd_int_enable(p); }else { diff --git a/src/typec/utcd.h b/src/typec/utcd.h index 06a62ef23..75ff6f1db 100644 --- a/src/typec/utcd.h +++ b/src/typec/utcd.h @@ -38,7 +38,7 @@ extern "C" { //--------------------------------------------------------------------+ #ifndef CFG_TUC_TASK_QUEUE_SZ -#define CFG_TUC_TASK_QUEUE_SZ 16 +#define CFG_TUC_TASK_QUEUE_SZ 8 #endif -- cgit v1.3.1 From debde4cc97cb7c6c13d62d0e3bbe195c80bfec9f Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 12 Jun 2023 12:14:55 +0700 Subject: response with request safe5v, get passed PS_READY --- src/common/tusb_types.h | 10 +++++ src/portable/st/typec/typec_stm32.c | 78 +++++++++++++++++++++++++++++-------- src/typec/tcd.h | 17 +++++++- src/typec/utcd.c | 59 ++++++++++++++++++++++++++++ src/typec/utcd.h | 34 +++++++++++++++- 5 files changed, 180 insertions(+), 18 deletions(-) (limited to 'src/portable') diff --git a/src/common/tusb_types.h b/src/common/tusb_types.h index c92320e5c..cad633ee4 100644 --- a/src/common/tusb_types.h +++ b/src/common/tusb_types.h @@ -562,6 +562,16 @@ enum { TUSB_PD_REV30 = 0x2, }; +enum { + TUSB_PD_DATA_ROLE_UFP = 0x0, + TUSB_PD_DATA_ROLE_DFP = 0x1, +}; + +enum { + TUSB_PD_POWER_ROLE_SINK = 0x0, + TUSB_PD_POWER_ROLE_SOURCE = 0x1, +}; + typedef struct TU_ATTR_PACKED { uint16_t msg_type : 5; // [0:4] uint16_t data_role : 1; // [5] SOP only: 0 UFP, 1 DFP diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index 1dba54492..9b3b21707 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -63,6 +63,9 @@ enum { static uint8_t const* _rx_buf; +static uint8_t const* _tx_pending_buf; +static uint16_t _tx_pending_bytes; +static uint16_t _tx_xferring_bytes; static tusb_pd_header_t _good_crc = { .msg_type = TUSB_PD_CTRL_GOOD_CRC, @@ -141,10 +144,21 @@ TU_ATTR_ALWAYS_INLINE static inline void dma_stop(uint8_t rhport, bool is_rx) { dma_ch->CCR &= ~DMA_CCR_EN; } +TU_ATTR_ALWAYS_INLINE static inline bool dma_enabled(uint8_t rhport, bool is_rx) { + DMA_Channel_TypeDef* dma_ch = (DMA_Channel_TypeDef*) dma_get_addr(rhport, is_rx); + return dma_ch->CCR & DMA_CCR_EN; +} + + TU_ATTR_ALWAYS_INLINE static inline void dma_tx_start(uint8_t rhport, void const* buf, uint16_t len) { UCPD1->TX_ORDSET = PHY_ORDERED_SET_SOP; UCPD1->TX_PAYSZ = len; dma_start(rhport, false, buf, len); + UCPD1->CR |= UCPD_CR_TXSEND; +} + +TU_ATTR_ALWAYS_INLINE static inline void dma_tx_stop(uint8_t rhport) { + dma_stop(rhport, false); } //--------------------------------------------------------------------+ @@ -203,11 +217,23 @@ bool tcd_rx_start(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes) { return true; } -bool tcd_tx_start(uint8_t rhport, uint8_t const* buffer, uint16_t total_bytes) { +bool tcd_msg_send(uint8_t rhport, uint8_t const* buffer, uint16_t total_bytes) { (void) rhport; - (void) buffer; - (void) total_bytes; - return false; + + if (dma_enabled(rhport, false)) { + // DMA is busy, probably sending GoodCRC, save as pending TX + _tx_pending_buf = buffer; + _tx_pending_bytes = total_bytes; + }else { + // DMA is free, start sending + _tx_pending_buf = NULL; + _tx_pending_bytes = 0; + + _tx_xferring_bytes = total_bytes; + dma_tx_start(rhport, buffer, total_bytes); + } + + return true; } void tcd_int_handler(uint8_t rhport) { @@ -275,6 +301,8 @@ void tcd_int_handler(uint8_t rhport) { // Received full message if (sr & UCPD_SR_RXMSGEND) { TU_LOG3("RX MSG END\n"); + + // stop TX dma_stop(rhport, true); uint8_t result; @@ -283,7 +311,6 @@ void tcd_int_handler(uint8_t rhport) { // response with good crc _good_crc.msg_id = ((tusb_pd_header_t const*) _rx_buf)->msg_id; dma_tx_start(rhport, &_good_crc, 2); - UCPD1->CR |= UCPD_CR_TXSEND; result = XFER_RESULT_SUCCESS; }else { @@ -305,19 +332,38 @@ void tcd_int_handler(uint8_t rhport) { } //------------- TX -------------// - if (sr & UCPD_SR_TXMSGSENT) { - TU_LOG3("TX MSG SENT\n"); - // all byte sent - dma_stop(rhport, false); + // All tx events: complete and error + if (sr & (UCPD_SR_TXMSGSENT | (UCPD_SR_TXMSGDISC | UCPD_SR_TXMSGABT | UCPD_SR_TXUND))) { + // force TX stop + dma_tx_stop(rhport); - // ack - UCPD1->ICR = UCPD_ICR_TXMSGSENTCF; - } + uint16_t const xferred_bytes = _tx_xferring_bytes - UCPD1->TX_PAYSZ; + uint8_t result; - if (sr & (UCPD_SR_TXMSGDISC | UCPD_SR_TXMSGABT | UCPD_SR_TXUND)) { - TU_LOG3("TX Error\n"); - dma_stop(rhport, false); - UCPD1->ICR = UCPD_SR_TXMSGDISC | UCPD_SR_TXMSGABT | UCPD_SR_TXUND; + if ( sr & UCPD_SR_TXMSGSENT ) { + TU_LOG3("TX MSG SENT\n"); + result = XFER_RESULT_SUCCESS; + // ack + UCPD1->ICR = UCPD_ICR_TXMSGSENTCF; + }else { + TU_LOG3("TX Error\n"); + result = XFER_RESULT_FAILED; + // ack + UCPD1->ICR = UCPD_SR_TXMSGDISC | UCPD_SR_TXMSGABT | UCPD_SR_TXUND; + } + + // start pending TX if any + if (_tx_pending_buf && _tx_pending_bytes ) { + // Start the pending TX + dma_tx_start(rhport, _tx_pending_buf, _tx_pending_bytes); + + // clear pending + _tx_pending_buf = NULL; + _tx_pending_bytes = 0; + } + + // notify stack + tcd_event_tx_complete(rhport, xferred_bytes, result, true); } } diff --git a/src/typec/tcd.h b/src/typec/tcd.h index 41dceaa74..b131d6ba9 100644 --- a/src/typec/tcd.h +++ b/src/typec/tcd.h @@ -43,6 +43,7 @@ enum { TCD_EVENT_INVALID = 0, TCD_EVENT_CC_CHANGED, TCD_EVENT_RX_COMPLETE, + TCD_EVENT_TX_COMPLETE, }; @@ -84,7 +85,7 @@ void tcd_int_handler(uint8_t rhport); //--------------------------------------------------------------------+ bool tcd_rx_start(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes); -bool tcd_tx_start(uint8_t rhport, uint8_t const* buffer, uint16_t total_bytes); +bool tcd_msg_send(uint8_t rhport, uint8_t const* buffer, uint16_t total_bytes); //--------------------------------------------------------------------+ // Event API (implemented by stack) @@ -120,4 +121,18 @@ void tcd_event_rx_complete(uint8_t rhport, uint16_t xferred_bytes, uint8_t resul tcd_event_handler(&event, in_isr); } +TU_ATTR_ALWAYS_INLINE static inline +void tcd_event_tx_complete(uint8_t rhport, uint16_t xferred_bytes, uint8_t result, bool in_isr) { + tcd_event_t event = { + .rhport = rhport, + .event_id = TCD_EVENT_TX_COMPLETE, + .rx_complete = { + .xferred_bytes = xferred_bytes, + .result = result + } + }; + + tcd_event_handler(&event, in_isr); +} + #endif diff --git a/src/typec/utcd.c b/src/typec/utcd.c index abbe8b43e..09031e5c9 100644 --- a/src/typec/utcd.c +++ b/src/typec/utcd.c @@ -53,6 +53,7 @@ static bool _port_inited[TUP_TYPEC_RHPORTS_NUM]; // Max possible PD size is 262 bytes static uint8_t _rx_buf[262] TU_ATTR_ALIGNED(4); +static uint8_t _tx_buf[100] TU_ATTR_ALIGNED(4); //--------------------------------------------------------------------+ // @@ -90,6 +91,19 @@ bool tuc_init(uint8_t rhport, tusb_typec_port_type_t port_type) { // //--------------------------------------------------------------------+ +bool utcd_msg_send(uint8_t rhport, tusb_pd_header_t const* header, void const* data) { + // copy header + memcpy(_tx_buf, header, sizeof(tusb_pd_header_t)); + + // copy data objcet if available + uint16_t const n_data_obj = header->n_data_obj; + if (n_data_obj > 0) { + memcpy(_tx_buf + sizeof(tusb_pd_header_t), data, n_data_obj * 4); + } + + return tcd_msg_send(rhport, _tx_buf, sizeof(tusb_pd_header_t) + n_data_obj * 4); +} + bool parse_message(uint8_t rhport, uint8_t const* buf, uint16_t len) { (void) rhport; uint8_t const* p_end = buf + len; @@ -98,10 +112,28 @@ bool parse_message(uint8_t rhport, uint8_t const* buf, uint16_t len) { if (header->n_data_obj == 0) { // control message + switch (header->msg_type) { + case TUSB_PD_CTRL_GOOD_CRC: + break; + + case TUSB_PD_CTRL_ACCEPT: + break; + + case TUSB_PD_CTRL_REJECT: + break; + + case TUSB_PD_CTRL_PS_RDY: + break; + + default: break; + } } else { // data message switch (header->msg_type) { case TUSB_PD_DATA_SOURCE_CAP: { + // Examine source capability and select a suitable PDO (starting from 1 with safe5v) + uint8_t obj_pos = 1; + for(size_t i=0; in_data_obj; i++) { TU_VERIFY(ptr < p_end); uint32_t const pdo = tu_le32toh(tu_unaligned_read32(ptr)); @@ -125,6 +157,33 @@ bool parse_message(uint8_t rhport, uint8_t const* buf, uint16_t len) { ptr += 4; } + + // Send request with selected PDO position as response to Source Cap + pd_rdo_fixed_variable_t rdo = { + .current_extremum_10ma = 50, // max 500mA + .current_operate_10ma = 30, // 300mA + .reserved = 0, + .epr_mode_capable = 0, + .unchunked_ext_msg_support = 0, + .no_usb_suspend = 0, + .usb_comm_capable = 1, + .capability_mismatch = 0, + .give_back_flag = 0, // exteremum is max + .object_position = obj_pos, + }; + + tusb_pd_header_t const req_header = { + .msg_type = TUSB_PD_DATA_REQUEST, + .data_role = TUSB_PD_DATA_ROLE_UFP, + .specs_rev = TUSB_PD_REV20, + .power_role = TUSB_PD_POWER_ROLE_SINK, + .msg_id = 0, + .n_data_obj = 1, + .extended = 0, + }; + + utcd_msg_send(rhport, &req_header, &rdo); + break; } diff --git a/src/typec/utcd.h b/src/typec/utcd.h index dbc909592..bb1523253 100644 --- a/src/typec/utcd.h +++ b/src/typec/utcd.h @@ -42,7 +42,7 @@ extern "C" { #endif //--------------------------------------------------------------------+ -// +// Source Capability //--------------------------------------------------------------------+ // All table references are from USBPD Specification rev3.1 version 1.8 @@ -102,6 +102,38 @@ typedef struct TU_ATTR_PACKED { } pd_pdo_apdo_t; TU_VERIFY_STATIC(sizeof(pd_pdo_apdo_t) == 4, "Invalid size"); +//--------------------------------------------------------------------+ +// Request +//--------------------------------------------------------------------+ + +typedef struct TU_ATTR_PACKED { + uint32_t current_extremum_10ma : 10; // [9..0] Max (give back = 0) or Min (give back = 1) current in 10mA unit + uint32_t current_operate_10ma : 10; // [19..10] Operating current in 10mA unit + uint32_t reserved : 2; // [21..20] Reserved + uint32_t epr_mode_capable : 1; // [22] EPR mode capable + uint32_t unchunked_ext_msg_support : 1; // [23] UnChunked Extended Message Supported + uint32_t no_usb_suspend : 1; // [24] No USB Suspend + uint32_t usb_comm_capable : 1; // [25] USB Communications Capable + uint32_t capability_mismatch : 1; // [26] Capability Mismatch + uint32_t give_back_flag : 1; // [27] GiveBack Flag: 0 = Max, 1 = Min + uint32_t object_position : 4; // [31..28] Object Position +} pd_rdo_fixed_variable_t; +TU_VERIFY_STATIC(sizeof(pd_rdo_fixed_variable_t) == 4, "Invalid size"); + +typedef struct TU_ATTR_PACKED { + uint32_t power_extremum_250mw : 10; // [9..0] Max (give back = 0) or Min (give back = 1) operating power in 250mW unit + uint32_t power_operate_250mw : 10; // [19..10] Operating power in 250mW unit + uint32_t reserved : 2; // [21..20] Reserved + uint32_t epr_mode_capable : 1; // [22] EPR mode capable + uint32_t unchunked_ext_msg_support : 1; // [23] UnChunked Extended Message Supported + uint32_t no_usb_suspend : 1; // [24] No USB Suspend + uint32_t usb_comm_capable : 1; // [25] USB Communications Capable + uint32_t capability_mismatch : 1; // [26] Capability Mismatch + uint32_t give_back_flag : 1; // [27] GiveBack Flag: 0 = Max, 1 = Min + uint32_t object_position : 4; // [31..28] Object Position +} pd_rdo_battery_t; +TU_VERIFY_STATIC(sizeof(pd_rdo_battery_t) == 4, "Invalid size"); + //--------------------------------------------------------------------+ // Application API //--------------------------------------------------------------------+ -- cgit v1.3.1 From c28503060c0c3cb09d8e2ce63d1b0009affbdf72 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 12 Jun 2023 14:57:50 +0700 Subject: ad pd_types.h --- src/common/tusb_types.h | 96 +-------------- src/portable/st/typec/typec_stm32.c | 13 +- src/typec/pd_types.h | 237 ++++++++++++++++++++++++++++++++++++ src/typec/tcd.h | 10 +- src/typec/utcd.c | 38 +++--- src/typec/utcd.h | 101 ++------------- 6 files changed, 278 insertions(+), 217 deletions(-) create mode 100644 src/typec/pd_types.h (limited to 'src/portable') diff --git a/src/common/tusb_types.h b/src/common/tusb_types.h index cad633ee4..fab680989 100644 --- a/src/common/tusb_types.h +++ b/src/common/tusb_types.h @@ -480,6 +480,7 @@ typedef struct TU_ATTR_PACKED //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ + typedef struct TU_ATTR_PACKED{ union { struct TU_ATTR_PACKED { @@ -499,101 +500,6 @@ typedef struct TU_ATTR_PACKED{ TU_VERIFY_STATIC( sizeof(tusb_control_request_t) == 8, "size is not correct"); -//--------------------------------------------------------------------+ -// TYPE-C -//--------------------------------------------------------------------+ - -typedef enum { - TUSB_TYPEC_PORT_SRC, - TUSB_TYPEC_PORT_SNK, - TUSB_TYPEC_PORT_DRP -} tusb_typec_port_type_t; - -typedef enum { - TUSB_PD_CTRL_RESERVED = 0, // 0b00000: 0 - TUSB_PD_CTRL_GOOD_CRC, // 0b00001: 1 - TUSB_PD_CTRL_GO_TO_MIN, // 0b00010: 2 - TUSB_PD_CTRL_ACCEPT, // 0b00011: 3 - TUSB_PD_CTRL_REJECT, // 0b00100: 4 - TUSB_PD_CTRL_PING, // 0b00101: 5 - TUSB_PD_CTRL_PS_RDY, // 0b00110: 6 - TUSB_PD_CTRL_GET_SOURCE_CAP, // 0b00111: 7 - TUSB_PD_CTRL_GET_SINK_CAP, // 0b01000: 8 - TUSB_PD_CTRL_DR_SWAP, // 0b01001: 9 - TUSB_PD_CTRL_PR_SWAP, // 0b01010: 10 - TUSB_PD_CTRL_VCONN_SWAP, // 0b01011: 11 - TUSB_PD_CTRL_WAIT, // 0b01100: 12 - TUSB_PD_CTRL_SOFT_RESET, // 0b01101: 13 - TUSB_PD_CTRL_DATA_RESET, // 0b01110: 14 - TUSB_PD_CTRL_DATA_RESET_COMPLETE, // 0b01111: 15 - TUSB_PD_CTRL_NOT_SUPPORTED, // 0b10000: 16 - TUSB_PD_CTRL_GET_SOURCE_CAP_EXTENDED, // 0b10001: 17 - TUSB_PD_CTRL_GET_STATUS, // 0b10010: 18 - TUSB_PD_CTRL_FR_SWAP, // 0b10011: 19 - TUSB_PD_CTRL_GET_PPS_STATUS, // 0b10100: 20 - TUSB_PD_CTRL_GET_COUNTRY_CODES, // 0b10101: 21 - TUSB_PD_CTRL_GET_SINK_CAP_EXTENDED, // 0b10110: 22 - TUSB_PD_CTRL_GET_SOURCE_INFO, // 0b10111: 23 - TUSB_PD_CTRL_REVISION, // 0b11000: 24 -} tusb_pd_ctrl_type_t; - -typedef enum { - TUSB_PD_DATA_RESERVED = 0, // 0b00000: 0 - TUSB_PD_DATA_SOURCE_CAP, // 0b00001: 1 - TUSB_PD_DATA_REQUEST, // 0b00010: 2 - TUSB_PD_DATA_BIST, // 0b00011: 3 - TUSB_PD_DATA_SINK_CAP, // 0b00100: 4 - TUSB_PD_DATA_BATTERY_STATUS, // 0b00101: 5 - TUSB_PD_DATA_ALERT, // 0b00110: 6 - TUSB_PD_DATA_GET_COUNTRY_INFO, // 0b00111: 7 - TUSB_PD_DATA_ENTER_USB, // 0b01000: 8 - TUSB_PD_DATA_EPR_REQUEST, // 0b01001: 9 - TUSB_PD_DATA_EPR_MODE, // 0b01010: 10 - TUSB_PD_DATA_SRC_INFO, // 0b01011: 11 - TUSB_PD_DATA_REVISION, // 0b01100: 12 - TUSB_PD_DATA_RESERVED_13, // 0b01101: 13 - TUSB_PD_DATA_RESERVED_14, // 0b01110: 14 - TUSB_PD_DATA_VENDOR_DEFINED, // 0b01111: 15 -} tusb_pd_data_type_t; - -enum { - TUSB_PD_REV10 = 0x0, - TUSB_PD_REV20 = 0x1, - TUSB_PD_REV30 = 0x2, -}; - -enum { - TUSB_PD_DATA_ROLE_UFP = 0x0, - TUSB_PD_DATA_ROLE_DFP = 0x1, -}; - -enum { - TUSB_PD_POWER_ROLE_SINK = 0x0, - TUSB_PD_POWER_ROLE_SOURCE = 0x1, -}; - -typedef struct TU_ATTR_PACKED { - uint16_t msg_type : 5; // [0:4] - uint16_t data_role : 1; // [5] SOP only: 0 UFP, 1 DFP - uint16_t specs_rev : 2; // [6:7] - uint16_t power_role : 1; // [8] SOP only: 0 Sink, 1 Source - uint16_t msg_id : 3; // [9:11] - uint16_t n_data_obj : 3; // [12:14] - uint16_t extended : 1; // [15] -} tusb_pd_header_t; - -TU_VERIFY_STATIC( sizeof(tusb_pd_header_t) == 2, "size is not correct"); - -typedef struct TU_ATTR_PACKED { - uint16_t data_size : 9; // [0:8] - uint16_t reserved : 1; // [9] - uint16_t request_chunk : 1; // [10] - uint16_t chunk_number : 4; // [11:14] - uint16_t chunked : 1; // [15] -} tusb_pd_header_extended_t; - -TU_VERIFY_STATIC( sizeof(tusb_pd_header_extended_t) == 2, "size is not correct"); - TU_ATTR_PACKED_END // End of all packed definitions TU_ATTR_BIT_FIELD_ORDER_END diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index 9b3b21707..b09dc5bae 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -67,10 +67,10 @@ static uint8_t const* _tx_pending_buf; static uint16_t _tx_pending_bytes; static uint16_t _tx_xferring_bytes; -static tusb_pd_header_t _good_crc = { - .msg_type = TUSB_PD_CTRL_GOOD_CRC, +static pd_header_t _good_crc = { + .msg_type = PD_CTRL_GOOD_CRC, .data_role = 0, // UFP - .specs_rev = TUSB_PD_REV20, + .specs_rev = PD_REV_20, .power_role = 0, // Sink .msg_id = 0, .n_data_obj = 0, @@ -149,7 +149,6 @@ TU_ATTR_ALWAYS_INLINE static inline bool dma_enabled(uint8_t rhport, bool is_rx) return dma_ch->CCR & DMA_CCR_EN; } - TU_ATTR_ALWAYS_INLINE static inline void dma_tx_start(uint8_t rhport, void const* buf, uint16_t len) { UCPD1->TX_ORDSET = PHY_ORDERED_SET_SOP; UCPD1->TX_PAYSZ = len; @@ -165,7 +164,7 @@ TU_ATTR_ALWAYS_INLINE static inline void dma_tx_stop(uint8_t rhport) { // //--------------------------------------------------------------------+ -bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type) { +bool tcd_init(uint8_t rhport, uint32_t port_type) { (void) rhport; // Init DMA for RX, TX @@ -211,7 +210,7 @@ void tcd_int_disable(uint8_t rhport) { NVIC_DisableIRQ(UCPD1_IRQn); } -bool tcd_rx_start(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes) { +bool tcd_msg_receive(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes) { _rx_buf = buffer; dma_start(rhport, true, buffer, total_bytes); return true; @@ -309,7 +308,7 @@ void tcd_int_handler(uint8_t rhport) { if (!(sr & UCPD_SR_RXERR)) { // response with good crc - _good_crc.msg_id = ((tusb_pd_header_t const*) _rx_buf)->msg_id; + _good_crc.msg_id = ((pd_header_t const*) _rx_buf)->msg_id; dma_tx_start(rhport, &_good_crc, 2); result = XFER_RESULT_SUCCESS; diff --git a/src/typec/pd_types.h b/src/typec/pd_types.h new file mode 100644 index 000000000..1b2968f65 --- /dev/null +++ b/src/typec/pd_types.h @@ -0,0 +1,237 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _TUSB_PD_TYPES_H_ +#define _TUSB_PD_TYPES_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +#include +#include +#include "common/tusb_compiler.h" + +// Start of all packed definitions for compiler without per-type packed +TU_ATTR_PACKED_BEGIN +TU_ATTR_BIT_FIELD_ORDER_BEGIN + +//--------------------------------------------------------------------+ +// TYPE-C +//--------------------------------------------------------------------+ + +typedef enum { + TUSB_TYPEC_PORT_SRC, + TUSB_TYPEC_PORT_SNK, + TUSB_TYPEC_PORT_DRP +} tusb_typec_port_type_t; + +enum { + PD_CTRL_RESERVED = 0, // 0b00000: 0 + PD_CTRL_GOOD_CRC, // 0b00001: 1 + PD_CTRL_GO_TO_MIN, // 0b00010: 2 + PD_CTRL_ACCEPT, // 0b00011: 3 + PD_CTRL_REJECT, // 0b00100: 4 + PD_CTRL_PING, // 0b00101: 5 + PD_CTRL_PS_READY, // 0b00110: 6 + PD_CTRL_GET_SOURCE_CAP, // 0b00111: 7 + PD_CTRL_GET_SINK_CAP, // 0b01000: 8 + PD_CTRL_DR_SWAP, // 0b01001: 9 + PD_CTRL_PR_SWAP, // 0b01010: 10 + PD_CTRL_VCONN_SWAP, // 0b01011: 11 + PD_CTRL_WAIT, // 0b01100: 12 + PD_CTRL_SOFT_RESET, // 0b01101: 13 + PD_CTRL_DATA_RESET, // 0b01110: 14 + PD_CTRL_DATA_RESET_COMPLETE, // 0b01111: 15 + PD_CTRL_NOT_SUPPORTED, // 0b10000: 16 + PD_CTRL_GET_SOURCE_CAP_EXTENDED, // 0b10001: 17 + PD_CTRL_GET_STATUS, // 0b10010: 18 + PD_CTRL_FR_SWAP, // 0b10011: 19 + PD_CTRL_GET_PPS_STATUS, // 0b10100: 20 + PD_CTRL_GET_COUNTRY_CODES, // 0b10101: 21 + PD_CTRL_GET_SINK_CAP_EXTENDED, // 0b10110: 22 + PD_CTRL_GET_SOURCE_INFO, // 0b10111: 23 + PD_CTRL_REVISION, // 0b11000: 24 +}; + +enum { + PD_DATA_RESERVED = 0, // 0b00000: 0 + PD_DATA_SOURCE_CAP, // 0b00001: 1 + PD_DATA_REQUEST, // 0b00010: 2 + PD_DATA_BIST, // 0b00011: 3 + PD_DATA_SINK_CAP, // 0b00100: 4 + PD_DATA_BATTERY_STATUS, // 0b00101: 5 + PD_DATA_ALERT, // 0b00110: 6 + PD_DATA_GET_COUNTRY_INFO, // 0b00111: 7 + PD_DATA_ENTER_USB, // 0b01000: 8 + PD_DATA_EPR_REQUEST, // 0b01001: 9 + PD_DATA_EPR_MODE, // 0b01010: 10 + PD_DATA_SRC_INFO, // 0b01011: 11 + PD_DATA_REVISION, // 0b01100: 12 + PD_DATA_RESERVED_13, // 0b01101: 13 + PD_DATA_RESERVED_14, // 0b01110: 14 + PD_DATA_VENDOR_DEFINED, // 0b01111: 15 +}; + +enum { + PD_REV_10 = 0x0, + PD_REV_20 = 0x1, + PD_REV_30 = 0x2, +}; + +enum { + PD_DATA_ROLE_UFP = 0x0, + PD_DATA_ROLE_DFP = 0x1, +}; + +enum { + PD_POWER_ROLE_SINK = 0x0, + PD_POWER_ROLE_SOURCE = 0x1, +}; + +typedef struct TU_ATTR_PACKED { + uint16_t msg_type : 5; // [0:4] + uint16_t data_role : 1; // [5] SOP only: 0 UFP, 1 DFP + uint16_t specs_rev : 2; // [6:7] + uint16_t power_role : 1; // [8] SOP only: 0 Sink, 1 Source + uint16_t msg_id : 3; // [9:11] + uint16_t n_data_obj : 3; // [12:14] + uint16_t extended : 1; // [15] +} pd_header_t; +TU_VERIFY_STATIC(sizeof(pd_header_t) == 2, "size is not correct"); + +typedef struct TU_ATTR_PACKED { + uint16_t data_size : 9; // [0:8] + uint16_t reserved : 1; // [9] + uint16_t request_chunk : 1; // [10] + uint16_t chunk_number : 4; // [11:14] + uint16_t chunked : 1; // [15] +} pd_header_extended_t; +TU_VERIFY_STATIC(sizeof(pd_header_extended_t) == 2, "size is not correct"); + +//--------------------------------------------------------------------+ +// Source Capability +//--------------------------------------------------------------------+ + +// All table references are from USBPD Specification rev3.1 version 1.8 +enum { + PD_PDO_TYPE_FIXED = 0, // Vmin = Vmax + PD_PDO_TYPE_BATTERY, + PD_PDO_TYPE_VARIABLE, // non-battery + PD_PDO_TYPE_APDO, // Augmented Power Data Object +}; + +// Fixed Power Data Object (PDO) table 6-9 +typedef struct TU_ATTR_PACKED { + uint32_t current_max_10ma : 10; // [9..0] Max current in 10mA unit + uint32_t voltage_50mv : 10; // [19..10] Voltage in 50mV unit + uint32_t current_peak : 2; // [21..20] Peak current + uint32_t reserved : 1; // [22] Reserved + uint32_t epr_mode_capable : 1; // [23] epr_mode_capable + uint32_t unchunked_ext_msg_support : 1; // [24] UnChunked Extended Message Supported + uint32_t dual_role_data : 1; // [25] Dual Role Data + uint32_t usb_comm_capable : 1; // [26] USB Communications Capable + uint32_t unconstrained_power : 1; // [27] Unconstrained Power + uint32_t usb_suspend_supported : 1; // [28] USB Suspend Supported + uint32_t dual_role_power : 1; // [29] Dual Role Power + uint32_t type : 2; // [30] Fixed Supply type = PD_PDO_TYPE_FIXED +} pd_pdo_fixed_t; +TU_VERIFY_STATIC(sizeof(pd_pdo_fixed_t) == 4, "Invalid size"); + +// Battery Power Data Object (PDO) table 6-12 +typedef struct TU_ATTR_PACKED { + uint32_t power_max_250mw : 10; // [9..0] Max allowable power in 250mW unit + uint32_t voltage_min_50mv : 10; // [19..10] Minimum voltage in 50mV unit + uint32_t voltage_max_50mv : 10; // [29..20] Maximum voltage in 50mV unit + uint32_t type : 2; // [31..30] Battery type = PD_PDO_TYPE_BATTERY +} pd_pdo_battery_t; +TU_VERIFY_STATIC(sizeof(pd_pdo_battery_t) == 4, "Invalid size"); + +// Variable Power Data Object (PDO) table 6-11 +typedef struct TU_ATTR_PACKED { + uint32_t current_max_10ma : 10; // [9..0] Max current in 10mA unit + uint32_t voltage_min_50mv : 10; // [19..10] Minimum voltage in 50mV unit + uint32_t voltage_max_50mv : 10; // [29..20] Maximum voltage in 50mV unit + uint32_t type : 2; // [31..30] Variable Supply type = PD_PDO_TYPE_VARIABLE +} pd_pdo_variable_t; +TU_VERIFY_STATIC(sizeof(pd_pdo_variable_t) == 4, "Invalid size"); + +// Augmented Power Data Object (PDO) table 6-13 +typedef struct TU_ATTR_PACKED { + uint32_t current_max_50ma : 7; // [6..0] Max current in 50mA unit + uint32_t reserved1 : 1; // [7] Reserved + uint32_t voltage_min_100mv : 8; // [15..8] Minimum Voltage in 100mV unit + uint32_t reserved2 : 1; // [16] Reserved + uint32_t voltage_max_100mv : 8; // [24..17] Maximum Voltage in 100mV unit + uint32_t reserved3 : 2; // [26..25] Reserved + uint32_t pps_power_limited : 1; // [27] PPS Power Limited + uint32_t spr_programmable : 2; // [29..28] SPR Programmable Power Supply + uint32_t type : 2; // [31..30] Augmented Power Data Object = PD_PDO_TYPE_APDO +} pd_pdo_apdo_t; +TU_VERIFY_STATIC(sizeof(pd_pdo_apdo_t) == 4, "Invalid size"); + +//--------------------------------------------------------------------+ +// Request +//--------------------------------------------------------------------+ + +typedef struct TU_ATTR_PACKED { + uint32_t current_extremum_10ma : 10; // [9..0] Max (give back = 0) or Min (give back = 1) current in 10mA unit + uint32_t current_operate_10ma : 10; // [19..10] Operating current in 10mA unit + uint32_t reserved : 2; // [21..20] Reserved + uint32_t epr_mode_capable : 1; // [22] EPR mode capable + uint32_t unchunked_ext_msg_support : 1; // [23] UnChunked Extended Message Supported + uint32_t no_usb_suspend : 1; // [24] No USB Suspend + uint32_t usb_comm_capable : 1; // [25] USB Communications Capable + uint32_t capability_mismatch : 1; // [26] Capability Mismatch + uint32_t give_back_flag : 1; // [27] GiveBack Flag: 0 = Max, 1 = Min + uint32_t object_position : 4; // [31..28] Object Position +} pd_rdo_fixed_variable_t; +TU_VERIFY_STATIC(sizeof(pd_rdo_fixed_variable_t) == 4, "Invalid size"); + +typedef struct TU_ATTR_PACKED { + uint32_t power_extremum_250mw : 10; // [9..0] Max (give back = 0) or Min (give back = 1) operating power in 250mW unit + uint32_t power_operate_250mw : 10; // [19..10] Operating power in 250mW unit + uint32_t reserved : 2; // [21..20] Reserved + uint32_t epr_mode_capable : 1; // [22] EPR mode capable + uint32_t unchunked_ext_msg_support : 1; // [23] UnChunked Extended Message Supported + uint32_t no_usb_suspend : 1; // [24] No USB Suspend + uint32_t usb_comm_capable : 1; // [25] USB Communications Capable + uint32_t capability_mismatch : 1; // [26] Capability Mismatch + uint32_t give_back_flag : 1; // [27] GiveBack Flag: 0 = Max, 1 = Min + uint32_t object_position : 4; // [31..28] Object Position +} pd_rdo_battery_t; +TU_VERIFY_STATIC(sizeof(pd_rdo_battery_t) == 4, "Invalid size"); + + +TU_ATTR_PACKED_END // End of all packed definitions +TU_ATTR_BIT_FIELD_ORDER_END + + +#ifdef __cplusplus +} +#endif + +#endif diff --git a/src/typec/tcd.h b/src/typec/tcd.h index b131d6ba9..ee73943bd 100644 --- a/src/typec/tcd.h +++ b/src/typec/tcd.h @@ -28,6 +28,8 @@ #define _TUSB_TCD_H_ #include "common/tusb_common.h" +#include "pd_types.h" + #include "osal/osal.h" #include "common/tusb_fifo.h" @@ -69,7 +71,7 @@ typedef struct { //--------------------------------------------------------------------+ // Initialize controller -bool tcd_init(uint8_t rhport, tusb_typec_port_type_t port_type); +bool tcd_init(uint8_t rhport, uint32_t port_type); // Enable interrupt void tcd_int_enable (uint8_t rhport); @@ -84,7 +86,7 @@ void tcd_int_handler(uint8_t rhport); // //--------------------------------------------------------------------+ -bool tcd_rx_start(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes); +bool tcd_msg_receive(uint8_t rhport, uint8_t* buffer, uint16_t total_bytes); bool tcd_msg_send(uint8_t rhport, uint8_t const* buffer, uint16_t total_bytes); //--------------------------------------------------------------------+ @@ -135,4 +137,8 @@ void tcd_event_tx_complete(uint8_t rhport, uint16_t xferred_bytes, uint8_t resul tcd_event_handler(&event, in_isr); } +#ifdef __cplusplus +} +#endif + #endif diff --git a/src/typec/utcd.c b/src/typec/utcd.c index 09031e5c9..439fe89b9 100644 --- a/src/typec/utcd.c +++ b/src/typec/utcd.c @@ -62,7 +62,7 @@ bool tuc_inited(uint8_t rhport) { return _utcd_inited && _port_inited[rhport]; } -bool tuc_init(uint8_t rhport, tusb_typec_port_type_t port_type) { +bool tuc_init(uint8_t rhport, uint32_t port_type) { // Initialize stack if (!_utcd_inited) { tu_memclr(_port_inited, sizeof(_port_inited)); @@ -91,38 +91,38 @@ bool tuc_init(uint8_t rhport, tusb_typec_port_type_t port_type) { // //--------------------------------------------------------------------+ -bool utcd_msg_send(uint8_t rhport, tusb_pd_header_t const* header, void const* data) { +bool utcd_msg_send(uint8_t rhport, pd_header_t const* header, void const* data) { // copy header - memcpy(_tx_buf, header, sizeof(tusb_pd_header_t)); + memcpy(_tx_buf, header, sizeof(pd_header_t)); // copy data objcet if available uint16_t const n_data_obj = header->n_data_obj; if (n_data_obj > 0) { - memcpy(_tx_buf + sizeof(tusb_pd_header_t), data, n_data_obj * 4); + memcpy(_tx_buf + sizeof(pd_header_t), data, n_data_obj * 4); } - return tcd_msg_send(rhport, _tx_buf, sizeof(tusb_pd_header_t) + n_data_obj * 4); + return tcd_msg_send(rhport, _tx_buf, sizeof(pd_header_t) + n_data_obj * 4); } bool parse_message(uint8_t rhport, uint8_t const* buf, uint16_t len) { (void) rhport; uint8_t const* p_end = buf + len; - tusb_pd_header_t const* header = (tusb_pd_header_t const*) buf; - uint8_t const * ptr = buf + sizeof(tusb_pd_header_t); + pd_header_t const* header = (pd_header_t const*) buf; + uint8_t const * ptr = buf + sizeof(pd_header_t); if (header->n_data_obj == 0) { // control message switch (header->msg_type) { - case TUSB_PD_CTRL_GOOD_CRC: + case PD_CTRL_GOOD_CRC: break; - case TUSB_PD_CTRL_ACCEPT: + case PD_CTRL_ACCEPT: break; - case TUSB_PD_CTRL_REJECT: + case PD_CTRL_REJECT: break; - case TUSB_PD_CTRL_PS_RDY: + case PD_CTRL_PS_READY: break; default: break; @@ -130,7 +130,7 @@ bool parse_message(uint8_t rhport, uint8_t const* buf, uint16_t len) { } else { // data message switch (header->msg_type) { - case TUSB_PD_DATA_SOURCE_CAP: { + case PD_DATA_SOURCE_CAP: { // Examine source capability and select a suitable PDO (starting from 1 with safe5v) uint8_t obj_pos = 1; @@ -172,11 +172,11 @@ bool parse_message(uint8_t rhport, uint8_t const* buf, uint16_t len) { .object_position = obj_pos, }; - tusb_pd_header_t const req_header = { - .msg_type = TUSB_PD_DATA_REQUEST, - .data_role = TUSB_PD_DATA_ROLE_UFP, - .specs_rev = TUSB_PD_REV20, - .power_role = TUSB_PD_POWER_ROLE_SINK, + pd_header_t const req_header = { + .msg_type = PD_DATA_REQUEST, + .data_role = PD_DATA_ROLE_UFP, + .specs_rev = PD_REV_20, + .power_role = PD_POWER_ROLE_SINK, .msg_id = 0, .n_data_obj = 1, .extended = 0, @@ -200,7 +200,7 @@ void tcd_event_handler(tcd_event_t const * event, bool in_isr) { case TCD_EVENT_CC_CHANGED: if (event->cc_changed.cc_state[0] || event->cc_changed.cc_state[1]) { // Attach - tcd_rx_start(event->rhport, _rx_buf, sizeof(_rx_buf)); + tcd_msg_receive(event->rhport, _rx_buf, sizeof(_rx_buf)); }else { // Detach } @@ -213,7 +213,7 @@ void tcd_event_handler(tcd_event_t const * event, bool in_isr) { } // start new rx - tcd_rx_start(event->rhport, _rx_buf, sizeof(_rx_buf)); + tcd_msg_receive(event->rhport, _rx_buf, sizeof(_rx_buf)); break; default: break; diff --git a/src/typec/utcd.h b/src/typec/utcd.h index bb1523253..740e477ac 100644 --- a/src/typec/utcd.h +++ b/src/typec/utcd.h @@ -28,6 +28,7 @@ #define _TUSB_UTCD_H_ #include "common/tusb_common.h" +#include "pd_types.h" #ifdef __cplusplus extern "C" { @@ -41,105 +42,12 @@ extern "C" { #define CFG_TUC_TASK_QUEUE_SZ 8 #endif -//--------------------------------------------------------------------+ -// Source Capability -//--------------------------------------------------------------------+ - -// All table references are from USBPD Specification rev3.1 version 1.8 -enum { - PD_PDO_TYPE_FIXED = 0, // Vmin = Vmax - PD_PDO_TYPE_BATTERY, - PD_PDO_TYPE_VARIABLE, // non-battery - PD_PDO_TYPE_APDO, // Augmented Power Data Object -}; - -// Fixed Power Data Object (PDO) table 6-9 -typedef struct TU_ATTR_PACKED { - uint32_t current_max_10ma : 10; // [9..0] Max current in 10mA unit - uint32_t voltage_50mv : 10; // [19..10] Voltage in 50mV unit - uint32_t current_peak : 2; // [21..20] Peak current - uint32_t reserved : 1; // [22] Reserved - uint32_t epr_mode_capable : 1; // [23] epr_mode_capable - uint32_t unchunked_ext_msg_support : 1; // [24] UnChunked Extended Message Supported - uint32_t dual_role_data : 1; // [25] Dual Role Data - uint32_t usb_comm_capable : 1; // [26] USB Communications Capable - uint32_t unconstrained_power : 1; // [27] Unconstrained Power - uint32_t usb_suspend_supported : 1; // [28] USB Suspend Supported - uint32_t dual_role_power : 1; // [29] Dual Role Power - uint32_t type : 2; // [30] Fixed Supply type = PD_PDO_TYPE_FIXED -} pd_pdo_fixed_t; -TU_VERIFY_STATIC(sizeof(pd_pdo_fixed_t) == 4, "Invalid size"); - -// Battery Power Data Object (PDO) table 6-12 -typedef struct TU_ATTR_PACKED { - uint32_t power_max_250mw : 10; // [9..0] Max allowable power in 250mW unit - uint32_t voltage_min_50mv : 10; // [19..10] Minimum voltage in 50mV unit - uint32_t voltage_max_50mv : 10; // [29..20] Maximum voltage in 50mV unit - uint32_t type : 2; // [31..30] Battery type = PD_PDO_TYPE_BATTERY -} pd_pdo_battery_t; -TU_VERIFY_STATIC(sizeof(pd_pdo_battery_t) == 4, "Invalid size"); - -// Variable Power Data Object (PDO) table 6-11 -typedef struct TU_ATTR_PACKED { - uint32_t current_max_10ma : 10; // [9..0] Max current in 10mA unit - uint32_t voltage_min_50mv : 10; // [19..10] Minimum voltage in 50mV unit - uint32_t voltage_max_50mv : 10; // [29..20] Maximum voltage in 50mV unit - uint32_t type : 2; // [31..30] Variable Supply type = PD_PDO_TYPE_VARIABLE -} pd_pdo_variable_t; -TU_VERIFY_STATIC(sizeof(pd_pdo_variable_t) == 4, "Invalid size"); - -// Augmented Power Data Object (PDO) table 6-13 -typedef struct TU_ATTR_PACKED { - uint32_t current_max_50ma : 7; // [6..0] Max current in 50mA unit - uint32_t reserved1 : 1; // [7] Reserved - uint32_t voltage_min_100mv : 8; // [15..8] Minimum Voltage in 100mV unit - uint32_t reserved2 : 1; // [16] Reserved - uint32_t voltage_max_100mv : 8; // [24..17] Maximum Voltage in 100mV unit - uint32_t reserved3 : 2; // [26..25] Reserved - uint32_t pps_power_limited : 1; // [27] PPS Power Limited - uint32_t spr_programmable : 2; // [29..28] SPR Programmable Power Supply - uint32_t type : 2; // [31..30] Augmented Power Data Object = PD_PDO_TYPE_APDO -} pd_pdo_apdo_t; -TU_VERIFY_STATIC(sizeof(pd_pdo_apdo_t) == 4, "Invalid size"); - -//--------------------------------------------------------------------+ -// Request -//--------------------------------------------------------------------+ - -typedef struct TU_ATTR_PACKED { - uint32_t current_extremum_10ma : 10; // [9..0] Max (give back = 0) or Min (give back = 1) current in 10mA unit - uint32_t current_operate_10ma : 10; // [19..10] Operating current in 10mA unit - uint32_t reserved : 2; // [21..20] Reserved - uint32_t epr_mode_capable : 1; // [22] EPR mode capable - uint32_t unchunked_ext_msg_support : 1; // [23] UnChunked Extended Message Supported - uint32_t no_usb_suspend : 1; // [24] No USB Suspend - uint32_t usb_comm_capable : 1; // [25] USB Communications Capable - uint32_t capability_mismatch : 1; // [26] Capability Mismatch - uint32_t give_back_flag : 1; // [27] GiveBack Flag: 0 = Max, 1 = Min - uint32_t object_position : 4; // [31..28] Object Position -} pd_rdo_fixed_variable_t; -TU_VERIFY_STATIC(sizeof(pd_rdo_fixed_variable_t) == 4, "Invalid size"); - -typedef struct TU_ATTR_PACKED { - uint32_t power_extremum_250mw : 10; // [9..0] Max (give back = 0) or Min (give back = 1) operating power in 250mW unit - uint32_t power_operate_250mw : 10; // [19..10] Operating power in 250mW unit - uint32_t reserved : 2; // [21..20] Reserved - uint32_t epr_mode_capable : 1; // [22] EPR mode capable - uint32_t unchunked_ext_msg_support : 1; // [23] UnChunked Extended Message Supported - uint32_t no_usb_suspend : 1; // [24] No USB Suspend - uint32_t usb_comm_capable : 1; // [25] USB Communications Capable - uint32_t capability_mismatch : 1; // [26] Capability Mismatch - uint32_t give_back_flag : 1; // [27] GiveBack Flag: 0 = Max, 1 = Min - uint32_t object_position : 4; // [31..28] Object Position -} pd_rdo_battery_t; -TU_VERIFY_STATIC(sizeof(pd_rdo_battery_t) == 4, "Invalid size"); - //--------------------------------------------------------------------+ // Application API //--------------------------------------------------------------------+ // Init typec stack on a port -bool tuc_init(uint8_t rhport, tusb_typec_port_type_t port_type); +bool tuc_init(uint8_t rhport, uint32_t port_type); // Check if typec port is initialized bool tuc_inited(uint8_t rhport); @@ -155,4 +63,9 @@ extern void tcd_int_handler(uint8_t rhport); // //--------------------------------------------------------------------+ + +#ifdef __cplusplus +} +#endif + #endif -- cgit v1.3.1 From d70403f1f496f5853251f83392ffe80130255489 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 15 Jun 2023 13:06:27 +0700 Subject: refactor khci to chipidea fs driver for device (host is not yet) --- .idea/cmake.xml | 3 +- .idea/runConfigurations/mcx947_jlink.xml | 2 +- .idea/runConfigurations/rt1010_jlink.xml | 2 +- .idea/runConfigurations/rt1060_jlink.xml | 2 +- hw/bsp/kinetis_kl/family.cmake | 2 +- hw/bsp/mcx/boards/mcxn947brk/board.cmake | 8 +- hw/bsp/mcx/family.c | 27 +- hw/bsp/mcx/family.cmake | 4 +- hw/bsp/mcx/family.mk | 17 +- src/common/tusb_mcu.h | 6 +- src/portable/chipidea/ci_fs/ci_fs_kinetis.h | 51 +++ src/portable/chipidea/ci_fs/ci_fs_mcx.h | 47 +++ src/portable/chipidea/ci_fs/ci_fs_type.h | 118 ++++++ src/portable/chipidea/ci_fs/dcd_ci_fs.c | 555 ++++++++++++++++++++++++++++ 14 files changed, 804 insertions(+), 40 deletions(-) create mode 100644 src/portable/chipidea/ci_fs/ci_fs_kinetis.h create mode 100644 src/portable/chipidea/ci_fs/ci_fs_mcx.h create mode 100644 src/portable/chipidea/ci_fs/ci_fs_type.h create mode 100644 src/portable/chipidea/ci_fs/dcd_ci_fs.c (limited to 'src/portable') diff --git a/.idea/cmake.xml b/.idea/cmake.xml index 3c016ccff..c9024715c 100644 --- a/.idea/cmake.xml +++ b/.idea/cmake.xml @@ -2,7 +2,7 @@ - + @@ -37,6 +37,7 @@ + \ No newline at end of file diff --git a/.idea/runConfigurations/mcx947_jlink.xml b/.idea/runConfigurations/mcx947_jlink.xml index 71616ab70..27661bec5 100644 --- a/.idea/runConfigurations/mcx947_jlink.xml +++ b/.idea/runConfigurations/mcx947_jlink.xml @@ -1,5 +1,5 @@ - + diff --git a/.idea/runConfigurations/rt1010_jlink.xml b/.idea/runConfigurations/rt1010_jlink.xml index e660a46ae..68ebb8885 100644 --- a/.idea/runConfigurations/rt1010_jlink.xml +++ b/.idea/runConfigurations/rt1010_jlink.xml @@ -1,5 +1,5 @@ - + diff --git a/.idea/runConfigurations/rt1060_jlink.xml b/.idea/runConfigurations/rt1060_jlink.xml index b9a47a2ce..014a4d1b1 100644 --- a/.idea/runConfigurations/rt1060_jlink.xml +++ b/.idea/runConfigurations/rt1060_jlink.xml @@ -1,5 +1,5 @@ - + diff --git a/hw/bsp/kinetis_kl/family.cmake b/hw/bsp/kinetis_kl/family.cmake index 77b932b8e..f491b3dee 100644 --- a/hw/bsp/kinetis_kl/family.cmake +++ b/hw/bsp/kinetis_kl/family.cmake @@ -88,7 +88,7 @@ function(family_configure_example TARGET) # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC # TinyUSB Port - ${TOP}/src/portable/nxp/khci/dcd_khci.c + ${TOP}/src/portable/chipidea/ci_fs/dcd_ci_fs.c ${TOP}/src/portable/nxp/khci/hcd_khci.c # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c diff --git a/hw/bsp/mcx/boards/mcxn947brk/board.cmake b/hw/bsp/mcx/boards/mcxn947brk/board.cmake index 650f10967..8c3280743 100644 --- a/hw/bsp/mcx/boards/mcxn947brk/board.cmake +++ b/hw/bsp/mcx/boards/mcxn947brk/board.cmake @@ -5,12 +5,14 @@ set(JLINK_DEVICE MCXN947_M33_0) set(PYOCD_TARGET MCXN947) set(NXPLINK_DEVICE MCXN947:MCXN947) +set(PORT 1) + function(update_board TARGET) target_compile_definitions(${TARGET} PUBLIC CPU_MCXN947VDF_cm33_core0 - # port 1 is highspeed - BOARD_TUD_RHPORT=1 - BOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED + BOARD_TUD_RHPORT=${PORT} + # port 0 is fullspeed, port 1 is highspeed + BOARD_TUD_MAX_SPEED=$ ) target_sources(${TARGET} PUBLIC ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/clock_config.c diff --git a/hw/bsp/mcx/family.c b/hw/bsp/mcx/family.c index 36d2f2d0a..4344ffc4e 100644 --- a/hw/bsp/mcx/family.c +++ b/hw/bsp/mcx/family.c @@ -66,6 +66,7 @@ void board_init(void) { BOARD_InitPins(); BOARD_InitBootClocks(); + CLOCK_SetupExtClocking(XTAL0_CLK_HZ); // 1ms tick timer SysTick_Config(SystemCoreClock / 1000); @@ -122,31 +123,13 @@ void board_init(void) // USB VBUS /* PORT0 PIN22 configured as USB0_VBUS */ - CLOCK_SetupExtClocking(XTAL0_CLK_HZ); - #if PORT_SUPPORT_DEVICE(0) // Port0 is Full Speed - /* Turn on USB0 Phy */ - POWER_DisablePD(kPDRUNCFG_PD_USB0_PHY); - - /* reset the IP to make sure it's in reset state. */ - RESET_PeripheralReset(kUSB0D_RST_SHIFT_RSTn); - RESET_PeripheralReset(kUSB0HSL_RST_SHIFT_RSTn); - RESET_PeripheralReset(kUSB0HMR_RST_SHIFT_RSTn); - - // Enable USB Clock Adjustments to trim the FRO for the full speed controller - ANACTRL->FRO192M_CTRL |= ANACTRL_FRO192M_CTRL_USBCLKADJ_MASK; - CLOCK_SetClkDiv(kCLOCK_DivUsb0Clk, 1, false); - CLOCK_AttachClk(kFRO_HF_to_USB0_CLK); - - /*According to reference manual, device mode setting has to be set by access usb host register */ - CLOCK_EnableClock(kCLOCK_Usbhsl0); // enable usb0 host clock - USBFSH->PORTMODE |= USBFSH_PORTMODE_DEV_ENABLE_MASK; - CLOCK_DisableClock(kCLOCK_Usbhsl0); // disable usb0 host clock - - /* enable USB Device clock */ - CLOCK_EnableUsbfs0DeviceClock(kCLOCK_UsbfsSrcFro, CLOCK_GetFreq(kCLOCK_FroHf)); + CLOCK_AttachClk(kCLK_48M_to_USB0); + CLOCK_EnableClock(kCLOCK_Usb0Ram); + CLOCK_EnableClock(kCLOCK_Usb0Fs); + CLOCK_EnableUsbfsClock(); #endif #if PORT_SUPPORT_DEVICE(1) diff --git a/hw/bsp/mcx/family.cmake b/hw/bsp/mcx/family.cmake index 1c85b51f8..7c5feaecf 100644 --- a/hw/bsp/mcx/family.cmake +++ b/hw/bsp/mcx/family.cmake @@ -88,8 +88,8 @@ function(family_configure_example TARGET) #---------- Port Specific ---------- # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC - # TinyUSB Port - ${TOP}/src/portable/chipidea/ci_hs/dcd_ci_hs.c + # TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS + ${TOP}/src/portable/chipidea/$ # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c diff --git a/hw/bsp/mcx/family.mk b/hw/bsp/mcx/family.mk index 2cd4c2448..2722c2038 100644 --- a/hw/bsp/mcx/family.mk +++ b/hw/bsp/mcx/family.mk @@ -16,21 +16,24 @@ CFLAGS += \ -DCFG_TUSB_MCU=OPT_MCU_MCXN9 \ -DBOARD_TUD_RHPORT=$(PORT) \ +# mcu driver cause following warnings +CFLAGS += -Wno-error=unused-parameter -Wno-error=old-style-declaration + +# All source paths should be relative to the top level. +LD_FILE ?= $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/$(MCU_CORE)_flash.ld + +# TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS ifeq ($(PORT), 1) $(info "PORT1 High Speed") CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED + SRC_C += src/portable/chipidea/ci_hs/dcd_ci_hs.c else $(info "PORT0 Full Speed") + CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED + SRC_C += src/portable/chipidea/ci_fs/dcd_ci_fs.c endif -# mcu driver cause following warnings -CFLAGS += -Wno-error=unused-parameter -Wno-error=old-style-declaration - -# All source paths should be relative to the top level. -LD_FILE ?= $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/$(MCU_CORE)_flash.ld - SRC_C += \ - src/portable/chipidea/ci_hs/dcd_ci_hs.c \ $(SDK_DIR)/devices/$(MCU_VARIANT)/system_$(MCU_CORE).c \ $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_clock.c \ $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_reset.c \ diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index f89467e75..485d6168d 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -79,7 +79,11 @@ #define TUP_RHPORT_HIGHSPEED 1 #elif TU_CHECK_MCU(OPT_MCU_MCXN9) - // NOTE: MCXN943 port 1 use chipidea HS, port 0 use chipidea FS + // USB0 is chipidea FS + #define TUP_USBIP_CHIPIDEA_FS + #define TUP_USBIP_CHIPIDEA_FS_MCX + + // USB1 is chipidea HS #define TUP_USBIP_CHIPIDEA_HS #define TUP_USBIP_EHCI diff --git a/src/portable/chipidea/ci_fs/ci_fs_kinetis.h b/src/portable/chipidea/ci_fs/ci_fs_kinetis.h new file mode 100644 index 000000000..cd21af1c7 --- /dev/null +++ b/src/portable/chipidea/ci_fs/ci_fs_kinetis.h @@ -0,0 +1,51 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _CI_FS_KINETIS_H +#define _CI_FS_KINETIS_H + +#include "fsl_device_registers.h" + +//static const ci_fs_controller_t _ci_controller[] = { +// {.reg_base = USB0_BASE, .irqnum = USB0_IRQn} +//}; + +#define CI_FS_REG(_port) ((ci_fs_regs_t*) USB0_BASE) +#define CI_REG CI_FS_REG(0) + +void dcd_int_enable(uint8_t rhport) +{ + (void) rhport; + NVIC_EnableIRQ(USB0_IRQn); +} + +void dcd_int_disable(uint8_t rhport) +{ + (void) rhport; + NVIC_DisableIRQ(USB0_IRQn); +} + +#endif diff --git a/src/portable/chipidea/ci_fs/ci_fs_mcx.h b/src/portable/chipidea/ci_fs/ci_fs_mcx.h new file mode 100644 index 000000000..3bfcd398e --- /dev/null +++ b/src/portable/chipidea/ci_fs/ci_fs_mcx.h @@ -0,0 +1,47 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _CI_FS_MCX_H +#define _CI_FS_MCX_H + +#include "fsl_device_registers.h" + +#define CI_FS_REG(_port) ((ci_fs_regs_t*) USBFS0_BASE) +#define CI_REG CI_FS_REG(0) + +void dcd_int_enable(uint8_t rhport) +{ + (void) rhport; + NVIC_EnableIRQ(USB0_FS_IRQn); +} + +void dcd_int_disable(uint8_t rhport) +{ + (void) rhport; + NVIC_DisableIRQ(USB0_FS_IRQn); +} + +#endif diff --git a/src/portable/chipidea/ci_fs/ci_fs_type.h b/src/portable/chipidea/ci_fs/ci_fs_type.h new file mode 100644 index 000000000..5a5e53fb0 --- /dev/null +++ b/src/portable/chipidea/ci_fs/ci_fs_type.h @@ -0,0 +1,118 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _CI_FS_TYPE_H +#define _CI_FS_TYPE_H + +#include + +#ifdef __cplusplus +extern "C" { +#endif + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +// Note: some MCUs can only access these registers in 8-bit mode +// align 4 is used to get rid of reserved fields +#define _va32 volatile TU_ATTR_ALIGNED(4) + +typedef struct { + _va32 uint8_t PER_ID; // [00] Peripheral ID register + _va32 uint8_t ID_COMP; // [04] Peripheral ID complement register + _va32 uint8_t REV; // [08] Peripheral revision register + _va32 uint8_t ADD_INFO; // [0C] Peripheral additional info register + _va32 uint8_t OTG_ISTAT; // [10] OTG Interrupt Status Register + _va32 uint8_t OTG_ICTRL; // [14] OTG Interrupt Control Register + _va32 uint8_t OTG_STAT; // [18] OTG Status Register + _va32 uint8_t OTG_CTRL; // [1C] OTG Control register + uint32_t reserved_20[24]; // [20] + _va32 uint8_t INT_STAT; // [80] Interrupt status register + _va32 uint8_t INT_EN; // [84] Interrupt enable register + _va32 uint8_t ERR_STAT; // [88] Error interrupt status register + _va32 uint8_t ERR_ENB; // [8C] Error interrupt enable register + _va32 uint8_t STAT; // [90] Status register + _va32 uint8_t CTL; // [94] Control register + _va32 uint8_t ADDR; // [98] Address register + _va32 uint8_t BDT_PAGE1; // [9C] BDT page register 1 + _va32 uint8_t FRM_NUML; // [A0] Frame number register + _va32 uint8_t FRM_NUMH; // [A4] Frame number register + _va32 uint8_t TOKEN; // [A8] Token register + _va32 uint8_t SOF_THLD; // [AC] SOF threshold register + _va32 uint8_t BDT_PAGE2; // [B0] BDT page register 2 + _va32 uint8_t BDT_PAGE3; // [B4] BDT page register 3 + + uint32_t reserved_b8; // [B8] + uint32_t reserved_bc; // [BC] + + struct { + _va32 uint8_t CTL; + }EP[16]; // [C0] Endpoint control register + + //----- Following is only found available in NXP Kinetis + _va32 uint8_t USBCTRL; // [100] USB Control register, + _va32 uint8_t OBSERVE; // [104] USB OTG Observe register, + _va32 uint8_t CONTROL; // [108] USB OTG Control register, + _va32 uint8_t USBTRC0; // [10C] USB Transceiver Control Register 0, + uint32_t reserved_110; // [110] + _va32 uint8_t USBFRMADJUST; // [114] Frame Adjust Register, + + //----- Following is only found available in NXP MCX + uint32_t reserved_118[3]; // [118] + _va32 uint8_t KEEP_ALIVE_CTRL; // [124] Keep Alive Mode Control, + _va32 uint8_t KEEP_ALIVE_WKCTRL; // [128] Keep Alive Mode Wakeup Control, + _va32 uint8_t MISCCTRL; // [12C] Miscellaneous Control, + _va32 uint8_t STALL_IL_DIS; // [130] Peripheral Mode Stall Disable for Endpoints[ 7..0] IN + _va32 uint8_t STALL_IH_DIS; // [134] Peripheral Mode Stall Disable for Endpoints[15..8] IN + _va32 uint8_t STALL_OL_DIS; // [138] Peripheral Mode Stall Disable for Endpoints[ 7..0] OUT + _va32 uint8_t STALL_OH_DIS; // [13C] Peripheral Mode Stall Disable for Endpoints[15..8] OUT + _va32 uint8_t CLK_RECOVER_CTRL; // [140] USB Clock Recovery Control, + _va32 uint8_t CLK_RECOVER_IRC_EN; // [144] FIRC Oscillator Enable, + uint32_t reserved_148[3]; // [148] + _va32 uint8_t CLK_RECOVER_INT_EN; // [154] Clock Recovery Combined Interrupt Enable, + uint32_t reserved_158; // [158] + _va32 uint8_t CLK_RECOVER_INT_STATUS; // [15C] Clock Recovery Separated Interrupt Status, +} ci_fs_regs_t; + +TU_VERIFY_STATIC(sizeof(ci_fs_regs_t) == 0x160, "Size is not correct"); + +typedef struct +{ + uint32_t reg_base; + uint32_t irqnum; +} ci_fs_controller_t; + +#ifdef __cplusplus + } +#endif + +#endif diff --git a/src/portable/chipidea/ci_fs/dcd_ci_fs.c b/src/portable/chipidea/ci_fs/dcd_ci_fs.c new file mode 100644 index 000000000..37265df8b --- /dev/null +++ b/src/portable/chipidea/ci_fs/dcd_ci_fs.c @@ -0,0 +1,555 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020 Koji Kitayama + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "tusb_option.h" + +#if CFG_TUD_ENABLED && defined(TUP_USBIP_CHIPIDEA_FS) + +#include "device/dcd.h" +#include "ci_fs_type.h" + +#if defined(TUP_USBIP_CHIPIDEA_FS_KINETIS) + #include "ci_fs_kinetis.h" +#elif defined(TUP_USBIP_CHIPIDEA_FS_MCX) + #include "ci_fs_mcx.h" +#else + #error "MCU is not supported" +#endif + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM DECLARATION +//--------------------------------------------------------------------+ + +enum { + TOK_PID_OUT = 0x1u, + TOK_PID_IN = 0x9u, + TOK_PID_SETUP = 0xDu, +}; + +typedef struct TU_ATTR_PACKED +{ + union { + uint32_t head; + struct { + union { + struct { + uint16_t : 2; + __IO uint16_t tok_pid : 4; + uint16_t data : 1; + __IO uint16_t own : 1; + uint16_t : 8; + }; + struct { + uint16_t : 2; + uint16_t bdt_stall : 1; + uint16_t dts : 1; + uint16_t ninc : 1; + uint16_t keep : 1; + uint16_t : 10; + }; + }; + __IO uint16_t bc : 10; + uint16_t : 6; + }; + }; + uint8_t *addr; +}buffer_descriptor_t; + +TU_VERIFY_STATIC( sizeof(buffer_descriptor_t) == 8, "size is not correct" ); + +typedef struct TU_ATTR_PACKED +{ + union { + uint32_t state; + struct { + uint32_t max_packet_size :11; + uint32_t : 5; + uint32_t odd : 1; + uint32_t :15; + }; + }; + uint16_t length; + uint16_t remaining; +}endpoint_state_t; + +TU_VERIFY_STATIC( sizeof(endpoint_state_t) == 8, "size is not correct" ); + +typedef struct +{ + union { + /* [#EP][OUT,IN][EVEN,ODD] */ + buffer_descriptor_t bdt[16][2][2]; + uint16_t bda[512]; + }; + TU_ATTR_ALIGNED(4) union { + endpoint_state_t endpoint[16][2]; + endpoint_state_t endpoint_unified[16 * 2]; + }; + uint8_t setup_packet[8]; + uint8_t addr; +}dcd_data_t; + +//--------------------------------------------------------------------+ +// INTERNAL OBJECT & FUNCTION DECLARATION +//--------------------------------------------------------------------+ +// BDT(Buffer Descriptor Table) must be 256-byte aligned +CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(512) static dcd_data_t _dcd; + +TU_VERIFY_STATIC( sizeof(_dcd.bdt) == 512, "size is not correct" ); + +static void prepare_next_setup_packet(uint8_t rhport) +{ + const unsigned out_odd = _dcd.endpoint[0][0].odd; + const unsigned in_odd = _dcd.endpoint[0][1].odd; + TU_ASSERT(0 == _dcd.bdt[0][0][out_odd].own, ); + + _dcd.bdt[0][0][out_odd].data = 0; + _dcd.bdt[0][0][out_odd ^ 1].data = 1; + _dcd.bdt[0][1][in_odd].data = 1; + _dcd.bdt[0][1][in_odd ^ 1].data = 0; + dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_OUT), + _dcd.setup_packet, sizeof(_dcd.setup_packet)); +} + +static void process_stall(uint8_t rhport) +{ + for (int i = 0; i < 16; ++i) { + uint32_t const ep_ctl = CI_REG->EP[i].CTL; + + if (ep_ctl & USB_ENDPT_EPSTALL_MASK) { + // prepare next setup if endpoint0 + if ( i == 0 ) prepare_next_setup_packet(rhport); + + // clear stall bit + CI_REG->EP[i].CTL = ep_ctl & ~USB_ENDPT_EPSTALL_MASK; + } + } +} + +static void process_tokdne(uint8_t rhport) +{ + const unsigned s = CI_REG->STAT; + CI_REG->INT_STAT = USB_ISTAT_TOKDNE_MASK; /* fetch the next token if received */ + + uint8_t const epnum = (s >> USB_STAT_ENDP_SHIFT); + uint8_t const dir = (s & USB_STAT_TX_MASK) >> USB_STAT_TX_SHIFT; + unsigned const odd = (s & USB_STAT_ODD_MASK) ? 1 : 0; + + buffer_descriptor_t *bd = (buffer_descriptor_t *)&_dcd.bda[s]; + endpoint_state_t *ep = &_dcd.endpoint_unified[s >> 3]; + + /* fetch pid before discarded by the next steps */ + const unsigned pid = bd->tok_pid; + + /* reset values for a next transfer */ + bd->bdt_stall = 0; + bd->dts = 1; + bd->ninc = 0; + bd->keep = 0; + /* update the odd variable to prepare for the next transfer */ + ep->odd = odd ^ 1; + if (pid == TOK_PID_SETUP) { + dcd_event_setup_received(rhport, bd->addr, true); + CI_REG->CTL &= ~USB_CTL_TXSUSPENDTOKENBUSY_MASK; + return; + } + + const unsigned bc = bd->bc; + const unsigned remaining = ep->remaining - bc; + if (remaining && bc == ep->max_packet_size) { + /* continue the transferring consecutive data */ + ep->remaining = remaining; + const int next_remaining = remaining - ep->max_packet_size; + if (next_remaining > 0) { + /* prepare to the after next transfer */ + bd->addr += ep->max_packet_size * 2; + bd->bc = next_remaining > ep->max_packet_size ? ep->max_packet_size: next_remaining; + __DSB(); + bd->own = 1; /* the own bit must set after addr */ + } + return; + } + const unsigned length = ep->length; + dcd_event_xfer_complete(rhport, + tu_edpt_addr(epnum, dir), + length - remaining, XFER_RESULT_SUCCESS, true); + if (0 == epnum && 0 == length) { + /* After completion a ZLP of control transfer, + * it prepares for the next steup transfer. */ + if (_dcd.addr) { + /* When the transfer was the SetAddress, + * the device address should be updated here. */ + CI_REG->ADDR = _dcd.addr; + _dcd.addr = 0; + } + prepare_next_setup_packet(rhport); + } +} + +static void process_bus_reset(uint8_t rhport) +{ + CI_REG->USBCTRL &= ~USB_USBCTRL_SUSP_MASK; + CI_REG->CTL |= USB_CTL_ODDRST_MASK; + CI_REG->ADDR = 0; + CI_REG->INT_EN = USB_INTEN_USBRSTEN_MASK | USB_INTEN_TOKDNEEN_MASK | USB_INTEN_SLEEPEN_MASK | + USB_INTEN_ERROREN_MASK | USB_INTEN_STALLEN_MASK; + + CI_REG->EP[0].CTL = USB_ENDPT_EPHSHK_MASK | USB_ENDPT_EPRXEN_MASK | USB_ENDPT_EPTXEN_MASK; + for (unsigned i = 1; i < 16; ++i) { + CI_REG->EP[i].CTL = 0; + } + buffer_descriptor_t *bd = _dcd.bdt[0][0]; + for (unsigned i = 0; i < sizeof(_dcd.bdt)/sizeof(*bd); ++i, ++bd) { + bd->head = 0; + } + const endpoint_state_t ep0 = { + .max_packet_size = CFG_TUD_ENDPOINT0_SIZE, + .odd = 0, + .length = 0, + .remaining = 0, + }; + _dcd.endpoint[0][0] = ep0; + _dcd.endpoint[0][1] = ep0; + tu_memclr(_dcd.endpoint[1], sizeof(_dcd.endpoint) - sizeof(_dcd.endpoint[0])); + _dcd.addr = 0; + prepare_next_setup_packet(rhport); + CI_REG->CTL &= ~USB_CTL_ODDRST_MASK; + dcd_event_bus_reset(rhport, TUSB_SPEED_FULL, true); +} + +static void process_bus_sleep(uint8_t rhport) +{ + // Enable resume & disable suspend interrupt + const unsigned inten = CI_REG->INT_EN; + + CI_REG->INT_EN = (inten & ~USB_INTEN_SLEEPEN_MASK) | USB_INTEN_RESUMEEN_MASK; + CI_REG->USBTRC0 |= USB_USBTRC0_USBRESMEN_MASK; + CI_REG->USBCTRL |= USB_USBCTRL_SUSP_MASK; + + dcd_event_bus_signal(rhport, DCD_EVENT_SUSPEND, true); +} + +static void process_bus_resume(uint8_t rhport) +{ + // Enable suspend & disable resume interrupt + const unsigned inten = CI_REG->INT_EN; + + CI_REG->USBCTRL &= ~USB_USBCTRL_SUSP_MASK; // will also clear USB_USBTRC0_USB_RESUME_INT_MASK + CI_REG->USBTRC0 &= ~USB_USBTRC0_USBRESMEN_MASK; + CI_REG->INT_EN = (inten & ~USB_INTEN_RESUMEEN_MASK) | USB_INTEN_SLEEPEN_MASK; + + dcd_event_bus_signal(rhport, DCD_EVENT_RESUME, true); +} + +/*------------------------------------------------------------------*/ +/* Device API + *------------------------------------------------------------------*/ +void dcd_init(uint8_t rhport) +{ + (void) rhport; + + CI_REG->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; + while (CI_REG->USBTRC0 & USB_USBTRC0_USBRESET_MASK); + + tu_memclr(&_dcd, sizeof(_dcd)); + CI_REG->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ + CI_REG->BDT_PAGE1 = (uint8_t)((uintptr_t)_dcd.bdt >> 8); + CI_REG->BDT_PAGE2 = (uint8_t)((uintptr_t)_dcd.bdt >> 16); + CI_REG->BDT_PAGE3 = (uint8_t)((uintptr_t)_dcd.bdt >> 24); + + CI_REG->INT_EN = USB_INTEN_USBRSTEN_MASK; + + dcd_connect(rhport); + // NVIC_ClearPendingIRQ(USB0_IRQn); +} + +void dcd_set_address(uint8_t rhport, uint8_t dev_addr) +{ + _dcd.addr = dev_addr & 0x7F; + /* Response with status first before changing device address */ + dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_IN), NULL, 0); +} + +void dcd_remote_wakeup(uint8_t rhport) +{ + (void) rhport; + + CI_REG->CTL |= USB_CTL_RESUME_MASK; + + unsigned cnt = SystemCoreClock / 1000; + while (cnt--) __NOP(); + + CI_REG->CTL &= ~USB_CTL_RESUME_MASK; +} + +void dcd_connect(uint8_t rhport) +{ + (void) rhport; + CI_REG->USBCTRL = 0; + CI_REG->CONTROL |= USB_CONTROL_DPPULLUPNONOTG_MASK; + CI_REG->CTL |= USB_CTL_USBENSOFEN_MASK; +} + +void dcd_disconnect(uint8_t rhport) +{ + (void) rhport; + CI_REG->CTL = 0; + CI_REG->CONTROL &= ~USB_CONTROL_DPPULLUPNONOTG_MASK; +} + +void dcd_sof_enable(uint8_t rhport, bool en) +{ + (void) rhport; + (void) en; + + // TODO implement later +} + +//--------------------------------------------------------------------+ +// Endpoint API +//--------------------------------------------------------------------+ +bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) +{ + (void) rhport; + + const unsigned ep_addr = ep_desc->bEndpointAddress; + const unsigned epn = tu_edpt_number(ep_addr); + const unsigned dir = tu_edpt_dir(ep_addr); + const unsigned xfer = ep_desc->bmAttributes.xfer; + endpoint_state_t *ep = &_dcd.endpoint[epn][dir]; + const unsigned odd = ep->odd; + buffer_descriptor_t *bd = _dcd.bdt[epn][dir]; + + /* No support for control transfer */ + TU_ASSERT(epn && (xfer != TUSB_XFER_CONTROL)); + + ep->max_packet_size = tu_edpt_packet_size(ep_desc); + unsigned val = USB_ENDPT_EPCTLDIS_MASK; + val |= (xfer != TUSB_XFER_ISOCHRONOUS) ? USB_ENDPT_EPHSHK_MASK: 0; + val |= dir ? USB_ENDPT_EPTXEN_MASK : USB_ENDPT_EPRXEN_MASK; + CI_REG->EP[epn].CTL |= val; + + if (xfer != TUSB_XFER_ISOCHRONOUS) { + bd[odd].dts = 1; + bd[odd].data = 0; + bd[odd ^ 1].dts = 1; + bd[odd ^ 1].data = 1; + } + + return true; +} + +void dcd_edpt_close_all(uint8_t rhport) +{ + dcd_int_disable(rhport); + + for (unsigned i = 1; i < 16; ++i) { + CI_REG->EP[i].CTL = 0; + } + + dcd_int_enable(rhport); + + buffer_descriptor_t *bd = _dcd.bdt[1][0]; + for (unsigned i = 2; i < sizeof(_dcd.bdt)/sizeof(*bd); ++i, ++bd) { + bd->head = 0; + } + + endpoint_state_t *ep = &_dcd.endpoint[1][0]; + for (unsigned i = 2; i < sizeof(_dcd.endpoint)/sizeof(*ep); ++i, ++ep) { + /* Clear except the odd */ + ep->max_packet_size = 0; + ep->length = 0; + ep->remaining = 0; + } +} + +void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) +{ + const unsigned epn = tu_edpt_number(ep_addr); + const unsigned dir = tu_edpt_dir(ep_addr); + endpoint_state_t *ep = &_dcd.endpoint[epn][dir]; + buffer_descriptor_t *bd = _dcd.bdt[epn][dir]; + const unsigned msk = dir ? USB_ENDPT_EPTXEN_MASK : USB_ENDPT_EPRXEN_MASK; + + dcd_int_disable(rhport); + + CI_REG->EP[epn].CTL &= ~msk; + ep->max_packet_size = 0; + ep->length = 0; + ep->remaining = 0; + bd[0].head = 0; + bd[1].head = 0; + + dcd_int_enable(rhport); +} + +bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes) +{ + const unsigned epn = tu_edpt_number(ep_addr); + const unsigned dir = tu_edpt_dir(ep_addr); + endpoint_state_t *ep = &_dcd.endpoint[epn][dir]; + buffer_descriptor_t *bd = &_dcd.bdt[epn][dir][ep->odd]; + TU_ASSERT(0 == bd->own); + + dcd_int_disable(rhport); + + ep->length = total_bytes; + ep->remaining = total_bytes; + + const unsigned mps = ep->max_packet_size; + if (total_bytes > mps) { + buffer_descriptor_t *next = ep->odd ? bd - 1: bd + 1; + /* When total_bytes is greater than the max packet size, + * it prepares to the next transfer to avoid NAK in advance. */ + next->bc = total_bytes >= 2 * mps ? mps: total_bytes - mps; + next->addr = buffer + mps; + next->own = 1; + } + bd->bc = total_bytes >= mps ? mps: total_bytes; + bd->addr = buffer; + __DSB(); + bd->own = 1; /* This bit must be set last */ + + dcd_int_enable(rhport); + + return true; +} + +void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) +{ + (void) rhport; + const unsigned epn = tu_edpt_number(ep_addr); + + if (0 == epn) { + CI_REG->EP[epn].CTL |= USB_ENDPT_EPSTALL_MASK; + } else { + const unsigned dir = tu_edpt_dir(ep_addr); + const unsigned odd = _dcd.endpoint[epn][dir].odd; + buffer_descriptor_t *bd = &_dcd.bdt[epn][dir][odd]; + TU_ASSERT(0 == bd->own,); + + dcd_int_disable(rhport); + + bd->bdt_stall = 1; + __DSB(); + bd->own = 1; /* This bit must be set last */ + + dcd_int_enable(rhport); + } +} + +void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) +{ + const unsigned epn = tu_edpt_number(ep_addr); + TU_VERIFY(epn,); + const unsigned dir = tu_edpt_dir(ep_addr); + const unsigned odd = _dcd.endpoint[epn][dir].odd; + buffer_descriptor_t *bd = _dcd.bdt[epn][dir]; + TU_VERIFY(bd[odd].own,); + + dcd_int_disable(rhport); + + bd[odd].own = 0; + __DSB(); + + // clear stall + bd[odd].bdt_stall = 0; + + // Reset data toggle + bd[odd ].data = 0; + bd[odd ^ 1].data = 1; + + // We already cleared this in ISR, but just clear it here to be safe + const uint32_t ep_ctl = CI_REG->EP[epn].CTL; + if (ep_ctl & USB_ENDPT_EPSTALL_MASK) { + CI_REG->EP[epn].CTL = ep_ctl & ~USB_ENDPT_EPSTALL_MASK; + } + + dcd_int_enable(rhport); +} + +//--------------------------------------------------------------------+ +// ISR +//--------------------------------------------------------------------+ +void dcd_int_handler(uint8_t rhport) +{ + uint32_t is = CI_REG->INT_STAT; + uint32_t msk = CI_REG->INT_EN; + + // clear non-enabled interrupts + CI_REG->INT_STAT = is & ~msk; + is &= msk; + + if (is & USB_ISTAT_ERROR_MASK) { + /* TODO: */ + uint32_t es = CI_REG->ERR_STAT; + CI_REG->ERR_STAT = es; + CI_REG->INT_STAT = is; /* discard any pending events */ + } + + if (is & USB_ISTAT_USBRST_MASK) { + CI_REG->INT_STAT = is; /* discard any pending events */ + process_bus_reset(rhport); + } + + if (is & USB_ISTAT_SLEEP_MASK) { + // TU_LOG2("Suspend: "); TU_LOG2_HEX(is); + + // Note Host usually has extra delay after bus reset (without SOF), which could falsely + // detected as Sleep event. Though usbd has debouncing logic so we are good + CI_REG->INT_STAT = USB_ISTAT_SLEEP_MASK; + process_bus_sleep(rhport); + } + +#if 0 // ISTAT_RESUME never trigger, probably for host mode ? + if (is & USB_ISTAT_RESUME_MASK) { + // TU_LOG2("ISTAT Resume: "); TU_LOG2_HEX(is); + KHCI->ISTAT = USB_ISTAT_RESUME_MASK; + process_bus_resume(rhport); + } +#endif + + if (CI_REG->USBTRC0 & USB_USBTRC0_USB_RESUME_INT_MASK) { + // TU_LOG2("USBTRC0 Resume: "); TU_LOG2_HEX(is); TU_LOG2_HEX(KHCI->USBTRC0); + process_bus_resume(rhport); + } + + if (is & USB_ISTAT_SOFTOK_MASK) { + CI_REG->INT_STAT = USB_ISTAT_SOFTOK_MASK; + dcd_event_bus_signal(rhport, DCD_EVENT_SOF, true); + } + + if (is & USB_ISTAT_STALL_MASK) { + CI_REG->INT_STAT = USB_ISTAT_STALL_MASK; + process_stall(rhport); + } + + if (is & USB_ISTAT_TOKDNE_MASK) { + process_tokdne(rhport); + } +} + +#endif -- cgit v1.3.1 From 96f7cd09dc2c8cd62afc5bb4b325ade45332e0ba Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 16 Jun 2023 10:45:59 +0700 Subject: remove legacy transdimension driver --- .../nxp/transdimension/common_transdimension.h | 136 ----- .../nxp/transdimension/dcd_transdimension.c | 672 --------------------- .../nxp/transdimension/hcd_transdimension.c | 119 ---- 3 files changed, 927 deletions(-) delete mode 100644 src/portable/nxp/transdimension/common_transdimension.h delete mode 100644 src/portable/nxp/transdimension/dcd_transdimension.c delete mode 100644 src/portable/nxp/transdimension/hcd_transdimension.c (limited to 'src/portable') diff --git a/src/portable/nxp/transdimension/common_transdimension.h b/src/portable/nxp/transdimension/common_transdimension.h deleted file mode 100644 index 95ae1903e..000000000 --- a/src/portable/nxp/transdimension/common_transdimension.h +++ /dev/null @@ -1,136 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#ifndef COMMON_TRANSDIMENSION_H_ -#define COMMON_TRANSDIMENSION_H_ - -#ifdef __cplusplus - extern "C" { -#endif - -// USBCMD -enum { - USBCMD_RUN_STOP = TU_BIT(0), - USBCMD_RESET = TU_BIT(1), - USBCMD_SETUP_TRIPWIRE = TU_BIT(13), - USBCMD_ADD_QTD_TRIPWIRE = TU_BIT(14) ///< This bit is used as a semaphore to ensure the to proper addition of a new dTD to an active (primed) endpoint’s linked list. This bit is set and cleared by software during the process of adding a new dTD -// Interrupt Threshold bit 23:16 -}; - -// PORTSC1 -#define PORTSC1_PORT_SPEED_POS 26 - -enum { - PORTSC1_CURRENT_CONNECT_STATUS = TU_BIT(0), - PORTSC1_FORCE_PORT_RESUME = TU_BIT(6), - PORTSC1_SUSPEND = TU_BIT(7), - PORTSC1_FORCE_FULL_SPEED = TU_BIT(24), - PORTSC1_PORT_SPEED = TU_BIT(26) | TU_BIT(27) -}; - -// OTGSC -enum { - OTGSC_VBUS_DISCHARGE = TU_BIT(0), - OTGSC_VBUS_CHARGE = TU_BIT(1), -// OTGSC_HWASSIST_AUTORESET = TU_BIT(2), - OTGSC_OTG_TERMINATION = TU_BIT(3), ///< Must set to 1 when OTG go to device mode - OTGSC_DATA_PULSING = TU_BIT(4), - OTGSC_ID_PULLUP = TU_BIT(5), -// OTGSC_HWASSIT_DATA_PULSE = TU_BIT(6), -// OTGSC_HWASSIT_BDIS_ACONN = TU_BIT(7), - OTGSC_ID = TU_BIT(8), ///< 0 = A device, 1 = B Device - OTGSC_A_VBUS_VALID = TU_BIT(9), - OTGSC_A_SESSION_VALID = TU_BIT(10), - OTGSC_B_SESSION_VALID = TU_BIT(11), - OTGSC_B_SESSION_END = TU_BIT(12), - OTGSC_1MS_TOGGLE = TU_BIT(13), - OTGSC_DATA_BUS_PULSING_STATUS = TU_BIT(14), -}; - -// USBMode -enum { - USBMODE_CM_DEVICE = 2, - USBMODE_CM_HOST = 3, - - USBMODE_SLOM = TU_BIT(3), - USBMODE_SDIS = TU_BIT(4), - - USBMODE_VBUS_POWER_SELECT = TU_BIT(5), // Need to be enabled for LPC18XX/43XX in host mode -}; - -// Device Registers -typedef struct -{ - //------------- ID + HW Parameter Registers-------------// - __I uint32_t TU_RESERVED[64]; ///< For iMX RT10xx, but not used by LPC18XX/LPC43XX - - //------------- Capability Registers-------------// - __I uint8_t CAPLENGTH; ///< Capability Registers Length - __I uint8_t TU_RESERVED[1]; - __I uint16_t HCIVERSION; ///< Host Controller Interface Version - - __I uint32_t HCSPARAMS; ///< Host Controller Structural Parameters - __I uint32_t HCCPARAMS; ///< Host Controller Capability Parameters - __I uint32_t TU_RESERVED[5]; - - __I uint16_t DCIVERSION; ///< Device Controller Interface Version - __I uint8_t TU_RESERVED[2]; - - __I uint32_t DCCPARAMS; ///< Device Controller Capability Parameters - __I uint32_t TU_RESERVED[6]; - - //------------- Operational Registers -------------// - __IO uint32_t USBCMD; ///< USB Command Register - __IO uint32_t USBSTS; ///< USB Status Register - __IO uint32_t USBINTR; ///< Interrupt Enable Register - __IO uint32_t FRINDEX; ///< USB Frame Index - __I uint32_t TU_RESERVED; - __IO uint32_t DEVICEADDR; ///< Device Address - __IO uint32_t ENDPTLISTADDR; ///< Endpoint List Address - __I uint32_t TU_RESERVED; - __IO uint32_t BURSTSIZE; ///< Programmable Burst Size - __IO uint32_t TXFILLTUNING; ///< TX FIFO Fill Tuning - uint32_t TU_RESERVED[4]; - __IO uint32_t ENDPTNAK; ///< Endpoint NAK - __IO uint32_t ENDPTNAKEN; ///< Endpoint NAK Enable - __I uint32_t TU_RESERVED; - __IO uint32_t PORTSC1; ///< Port Status & Control - __I uint32_t TU_RESERVED[7]; - __IO uint32_t OTGSC; ///< On-The-Go Status & control - __IO uint32_t USBMODE; ///< USB Device Mode - __IO uint32_t ENDPTSETUPSTAT; ///< Endpoint Setup Status - __IO uint32_t ENDPTPRIME; ///< Endpoint Prime - __IO uint32_t ENDPTFLUSH; ///< Endpoint Flush - __I uint32_t ENDPTSTAT; ///< Endpoint Status - __IO uint32_t ENDPTCOMPLETE; ///< Endpoint Complete - __IO uint32_t ENDPTCTRL[8]; ///< Endpoint Control 0 - 7 -} dcd_registers_t, hcd_registers_t; - -#ifdef __cplusplus - } -#endif - -#endif /* COMMON_TRANSDIMENSION_H_ */ diff --git a/src/portable/nxp/transdimension/dcd_transdimension.c b/src/portable/nxp/transdimension/dcd_transdimension.c deleted file mode 100644 index 983d7cfcf..000000000 --- a/src/portable/nxp/transdimension/dcd_transdimension.c +++ /dev/null @@ -1,672 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "tusb_option.h" - -#if CFG_TUD_ENABLED && \ - (CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT) - -#warning "transdimenion is renamed to chipidea (portable/chipidea/ci_hs) to match other opensource naming convention such as linux. This file will be removed in the future, please update your makefile accordingly" - -//--------------------------------------------------------------------+ -// INCLUDE -//--------------------------------------------------------------------+ -#if CFG_TUSB_MCU == OPT_MCU_MIMXRT - #include "fsl_device_registers.h" - #define INCLUDE_FSL_DEVICE_REGISTERS -#else - // LPCOpen for 18xx & 43xx - #include "chip.h" -#endif - -#include "common/tusb_common.h" -#include "device/dcd.h" -#include "common_transdimension.h" - -#if defined(__CORTEX_M) && __CORTEX_M == 7 && __DCACHE_PRESENT == 1 - #define CleanInvalidateDCache_by_Addr SCB_CleanInvalidateDCache_by_Addr -#else - #define CleanInvalidateDCache_by_Addr(_addr, _dsize) -#endif - -//--------------------------------------------------------------------+ -// MACRO CONSTANT TYPEDEF -//--------------------------------------------------------------------+ - -// ENDPTCTRL -enum { - ENDPTCTRL_STALL = TU_BIT(0), - ENDPTCTRL_TOGGLE_INHIBIT = TU_BIT(5), // used for test only - ENDPTCTRL_TOGGLE_RESET = TU_BIT(6), - ENDPTCTRL_ENABLE = TU_BIT(7) -}; - -enum { - ENDPTCTRL_TYPE_POS = 2, // Endpoint type is 2-bit field -}; - -// USBSTS, USBINTR -enum { - INTR_USB = TU_BIT(0), - INTR_ERROR = TU_BIT(1), - INTR_PORT_CHANGE = TU_BIT(2), - INTR_RESET = TU_BIT(6), - INTR_SOF = TU_BIT(7), - INTR_SUSPEND = TU_BIT(8), - INTR_NAK = TU_BIT(16) -}; - -// Queue Transfer Descriptor -typedef struct -{ - // Word 0: Next QTD Pointer - uint32_t next; ///< Next link pointer This field contains the physical memory address of the next dTD to be processed - - // Word 1: qTQ Token - uint32_t : 3 ; - volatile uint32_t xact_err : 1 ; - uint32_t : 1 ; - volatile uint32_t buffer_err : 1 ; - volatile uint32_t halted : 1 ; - volatile uint32_t active : 1 ; - uint32_t : 2 ; - uint32_t iso_mult_override : 2 ; ///< This field can be used for transmit ISOs to override the MULT field in the dQH. This field must be zero for all packet types that are not transmit-ISO. - uint32_t : 3 ; - uint32_t int_on_complete : 1 ; - volatile uint32_t total_bytes : 15 ; - uint32_t : 1 ; - - // Word 2-6: Buffer Page Pointer List, Each element in the list is a 4K page aligned, physical memory address. The lower 12 bits in each pointer are reserved (except for the first one) as each memory pointer must reference the start of a 4K page - uint32_t buffer[5]; ///< buffer1 has frame_n for TODO Isochronous - - //--------------------------------------------------------------------+ - // TD is 32 bytes aligned but occupies only 28 bytes - // Therefore there are 4 bytes padding that we can use. - //--------------------------------------------------------------------+ - uint16_t expected_bytes; - uint8_t reserved[2]; -} dcd_qtd_t; - -TU_VERIFY_STATIC( sizeof(dcd_qtd_t) == 32, "size is not correct"); - -// Queue Head -typedef struct -{ - // Word 0: Capabilities and Characteristics - uint32_t : 15 ; ///< Number of packets executed per transaction descriptor 00 - Execute N transactions as demonstrated by the USB variable length protocol where N is computed using Max_packet_length and the Total_bytes field in the dTD. 01 - Execute one transaction 10 - Execute two transactions 11 - Execute three transactions Remark: Non-isochronous endpoints must set MULT = 00. Remark: Isochronous endpoints must set MULT = 01, 10, or 11 as needed. - uint32_t int_on_setup : 1 ; ///< Interrupt on setup This bit is used on control type endpoints to indicate if USBINT is set in response to a setup being received. - uint32_t max_packet_size : 11 ; ///< Endpoint's wMaxPacketSize - uint32_t : 2 ; - uint32_t zero_length_termination : 1 ; ///< This bit is used for non-isochronous endpoints to indicate when a zero-length packet is received to terminate transfers in case the total transfer length is “multiple”. 0 - Enable zero-length packet to terminate transfers equal to a multiple of Max_packet_length (default). 1 - Disable zero-length packet on transfers that are equal in length to a multiple Max_packet_length. - uint32_t iso_mult : 2 ; ///< - - // Word 1: Current qTD Pointer - volatile uint32_t qtd_addr; - - // Word 2-9: Transfer Overlay - volatile dcd_qtd_t qtd_overlay; - - // Word 10-11: Setup request (control OUT only) - volatile tusb_control_request_t setup_request; - - //--------------------------------------------------------------------+ - // QHD is 64 bytes aligned but occupies only 48 bytes - // Therefore there are 16 bytes padding that we can use. - //--------------------------------------------------------------------+ - tu_fifo_t * ff; - uint8_t reserved[12]; -} dcd_qhd_t; - -TU_VERIFY_STATIC( sizeof(dcd_qhd_t) == 64, "size is not correct"); - -//--------------------------------------------------------------------+ -// Variables -//--------------------------------------------------------------------+ - -typedef struct -{ - dcd_registers_t* regs; // registers - const IRQn_Type irqnum; // IRQ number - const uint8_t ep_count; // Max bi-directional Endpoints -}dcd_controller_t; - -#if CFG_TUSB_MCU == OPT_MCU_MIMXRT - static const dcd_controller_t _dcd_controller[] = - { - // RT1010 and RT1020 only has 1 USB controller - #if FSL_FEATURE_SOC_USBHS_COUNT == 1 - { .regs = (dcd_registers_t*) USB_BASE , .irqnum = USB_OTG1_IRQn, .ep_count = 8 } - #else - { .regs = (dcd_registers_t*) USB1_BASE, .irqnum = USB_OTG1_IRQn, .ep_count = 8 }, - { .regs = (dcd_registers_t*) USB2_BASE, .irqnum = USB_OTG2_IRQn, .ep_count = 8 } - #endif - }; - -#else - static const dcd_controller_t _dcd_controller[] = - { - { .regs = (dcd_registers_t*) LPC_USB0_BASE, .irqnum = USB0_IRQn, .ep_count = 6 }, - { .regs = (dcd_registers_t*) LPC_USB1_BASE, .irqnum = USB1_IRQn, .ep_count = 4 } - }; -#endif - -#define QTD_NEXT_INVALID 0x01 - -typedef struct { - // Must be at 2K alignment - // Each endpoint with direction (IN/OUT) occupies a queue head - // for portability, TinyUSB only queue 1 TD for each Qhd - dcd_qhd_t qhd[TUP_DCD_ENDPOINT_MAX][2] TU_ATTR_ALIGNED(64); - dcd_qtd_t qtd[TUP_DCD_ENDPOINT_MAX][2] TU_ATTR_ALIGNED(32); -}dcd_data_t; - -CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(2048) -static dcd_data_t _dcd_data; - -//--------------------------------------------------------------------+ -// Controller API -//--------------------------------------------------------------------+ - -/// follows LPC43xx User Manual 23.10.3 -static void bus_reset(uint8_t rhport) -{ - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - - // The reset value for all endpoint types is the control endpoint. If one endpoint - // direction is enabled and the paired endpoint of opposite direction is disabled, then the - // endpoint type of the unused direction must be changed from the control type to any other - // type (e.g. bulk). Leaving an un-configured endpoint control will cause undefined behavior - // for the data PID tracking on the active endpoint. - for( uint8_t i=1; i < _dcd_controller[rhport].ep_count; i++) - { - dcd_reg->ENDPTCTRL[i] = (TUSB_XFER_BULK << ENDPTCTRL_TYPE_POS) | (TUSB_XFER_BULK << (16+ENDPTCTRL_TYPE_POS)); - } - - //------------- Clear All Registers -------------// - dcd_reg->ENDPTNAK = dcd_reg->ENDPTNAK; - dcd_reg->ENDPTNAKEN = 0; - dcd_reg->USBSTS = dcd_reg->USBSTS; - dcd_reg->ENDPTSETUPSTAT = dcd_reg->ENDPTSETUPSTAT; - dcd_reg->ENDPTCOMPLETE = dcd_reg->ENDPTCOMPLETE; - - while (dcd_reg->ENDPTPRIME) {} - dcd_reg->ENDPTFLUSH = 0xFFFFFFFF; - while (dcd_reg->ENDPTFLUSH) {} - - // read reset bit in portsc - - //------------- Queue Head & Queue TD -------------// - tu_memclr(&_dcd_data, sizeof(dcd_data_t)); - - //------------- Set up Control Endpoints (0 OUT, 1 IN) -------------// - _dcd_data.qhd[0][0].zero_length_termination = _dcd_data.qhd[0][1].zero_length_termination = 1; - _dcd_data.qhd[0][0].max_packet_size = _dcd_data.qhd[0][1].max_packet_size = CFG_TUD_ENDPOINT0_SIZE; - _dcd_data.qhd[0][0].qtd_overlay.next = _dcd_data.qhd[0][1].qtd_overlay.next = QTD_NEXT_INVALID; - - _dcd_data.qhd[0][0].int_on_setup = 1; // OUT only -} - -void dcd_init(uint8_t rhport) -{ - tu_memclr(&_dcd_data, sizeof(dcd_data_t)); - - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - - // Reset controller - dcd_reg->USBCMD |= USBCMD_RESET; - while( dcd_reg->USBCMD & USBCMD_RESET ) {} - - // Set mode to device, must be set immediately after reset - dcd_reg->USBMODE = USBMODE_CM_DEVICE; - dcd_reg->OTGSC = OTGSC_VBUS_DISCHARGE | OTGSC_OTG_TERMINATION; - -#if !TUD_OPT_HIGH_SPEED - dcd_reg->PORTSC1 = PORTSC1_FORCE_FULL_SPEED; -#endif - - CleanInvalidateDCache_by_Addr((uint32_t*) &_dcd_data, sizeof(dcd_data_t)); - - dcd_reg->ENDPTLISTADDR = (uint32_t) _dcd_data.qhd; // Endpoint List Address has to be 2K alignment - dcd_reg->USBSTS = dcd_reg->USBSTS; - dcd_reg->USBINTR = INTR_USB | INTR_ERROR | INTR_PORT_CHANGE | INTR_SUSPEND; - - dcd_reg->USBCMD &= ~0x00FF0000; // Interrupt Threshold Interval = 0 - dcd_reg->USBCMD |= USBCMD_RUN_STOP; // Connect -} - -void dcd_int_enable(uint8_t rhport) -{ - NVIC_EnableIRQ(_dcd_controller[rhport].irqnum); -} - -void dcd_int_disable(uint8_t rhport) -{ - NVIC_DisableIRQ(_dcd_controller[rhport].irqnum); -} - -void dcd_set_address(uint8_t rhport, uint8_t dev_addr) -{ - // Response with status first before changing device address - dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_IN), NULL, 0); - - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->DEVICEADDR = (dev_addr << 25) | TU_BIT(24); -} - -void dcd_remote_wakeup(uint8_t rhport) -{ - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->PORTSC1 |= PORTSC1_FORCE_PORT_RESUME; -} - -void dcd_connect(uint8_t rhport) -{ - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->USBCMD |= USBCMD_RUN_STOP; -} - -void dcd_disconnect(uint8_t rhport) -{ - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->USBCMD &= ~USBCMD_RUN_STOP; -} - -void dcd_sof_enable(uint8_t rhport, bool en) -{ - (void) rhport; - (void) en; - - // TODO implement later -} - -//--------------------------------------------------------------------+ -// HELPER -//--------------------------------------------------------------------+ - -static void qtd_init(dcd_qtd_t* p_qtd, void * data_ptr, uint16_t total_bytes) -{ - // Force the CPU to flush the buffer. We increase the size by 31 because the call aligns the - // address to 32-byte boundaries. Buffer must be word aligned - CleanInvalidateDCache_by_Addr((uint32_t*) tu_align((uint32_t) data_ptr, 4), total_bytes + 31); - - tu_memclr(p_qtd, sizeof(dcd_qtd_t)); - - p_qtd->next = QTD_NEXT_INVALID; - p_qtd->active = 1; - p_qtd->total_bytes = p_qtd->expected_bytes = total_bytes; - p_qtd->int_on_complete = true; - - if (data_ptr != NULL) - { - p_qtd->buffer[0] = (uint32_t) data_ptr; - - uint32_t const bufend = p_qtd->buffer[0] + total_bytes; - for(uint8_t i=1; i<5; i++) - { - uint32_t const next_page = tu_align4k( p_qtd->buffer[i-1] ) + 4096; - if ( bufend <= next_page ) break; - - p_qtd->buffer[i] = next_page; - - // TODO page[1] FRAME_N for ISO transfer - } - } -} - -//--------------------------------------------------------------------+ -// DCD Endpoint Port -//--------------------------------------------------------------------+ -void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) -{ - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->ENDPTCTRL[epnum] |= ENDPTCTRL_STALL << (dir ? 16 : 0); - - // flush to abort any primed buffer - dcd_reg->ENDPTFLUSH = TU_BIT(epnum + (dir ? 16 : 0)); -} - -void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) -{ - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - // data toggle also need to be reset - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->ENDPTCTRL[epnum] |= ENDPTCTRL_TOGGLE_RESET << ( dir ? 16 : 0 ); - dcd_reg->ENDPTCTRL[epnum] &= ~(ENDPTCTRL_STALL << ( dir ? 16 : 0)); -} - -bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) -{ - uint8_t const epnum = tu_edpt_number(p_endpoint_desc->bEndpointAddress); - uint8_t const dir = tu_edpt_dir(p_endpoint_desc->bEndpointAddress); - - // Must not exceed max endpoint number - TU_ASSERT( epnum < _dcd_controller[rhport].ep_count ); - - //------------- Prepare Queue Head -------------// - dcd_qhd_t * p_qhd = &_dcd_data.qhd[epnum][dir]; - tu_memclr(p_qhd, sizeof(dcd_qhd_t)); - - p_qhd->zero_length_termination = 1; - p_qhd->max_packet_size = tu_edpt_packet_size(p_endpoint_desc); - if (p_endpoint_desc->bmAttributes.xfer == TUSB_XFER_ISOCHRONOUS) - { - p_qhd->iso_mult = 1; - } - - p_qhd->qtd_overlay.next = QTD_NEXT_INVALID; - - CleanInvalidateDCache_by_Addr((uint32_t*) &_dcd_data, sizeof(dcd_data_t)); - - // Enable EP Control - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - - uint32_t const epctrl = (p_endpoint_desc->bmAttributes.xfer << ENDPTCTRL_TYPE_POS) | ENDPTCTRL_ENABLE | ENDPTCTRL_TOGGLE_RESET; - - if ( dir == TUSB_DIR_OUT ) - { - dcd_reg->ENDPTCTRL[epnum] = (dcd_reg->ENDPTCTRL[epnum] & 0xFFFF0000u) | epctrl; - }else - { - dcd_reg->ENDPTCTRL[epnum] = (dcd_reg->ENDPTCTRL[epnum] & 0x0000FFFFu) | (epctrl << 16); - } - - return true; -} - -void dcd_edpt_close_all (uint8_t rhport) -{ - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - - // Disable all non-control endpoints - for( uint8_t epnum=1; epnum < _dcd_controller[rhport].ep_count; epnum++) - { - _dcd_data.qhd[epnum][TUSB_DIR_OUT].qtd_overlay.halted = 1; - _dcd_data.qhd[epnum][TUSB_DIR_IN ].qtd_overlay.halted = 1; - - dcd_reg->ENDPTFLUSH = TU_BIT(epnum) | TU_BIT(epnum+16); - dcd_reg->ENDPTCTRL[epnum] = (TUSB_XFER_BULK << ENDPTCTRL_TYPE_POS) | (TUSB_XFER_BULK << (16+ENDPTCTRL_TYPE_POS)); - } -} - -void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) -{ - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - - _dcd_data.qhd[epnum][dir].qtd_overlay.halted = 1; - - // Flush EP - uint32_t const flush_mask = TU_BIT(epnum + (dir ? 16 : 0)); - dcd_reg->ENDPTFLUSH = flush_mask; - while(dcd_reg->ENDPTFLUSH & flush_mask); - - // Clear EP enable - dcd_reg->ENDPTCTRL[epnum] &=~(ENDPTCTRL_ENABLE << (dir ? 16 : 0)); -} - -static void qhd_start_xfer(uint8_t rhport, uint8_t epnum, uint8_t dir) -{ - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_qhd_t* p_qhd = &_dcd_data.qhd[epnum][dir]; - dcd_qtd_t* p_qtd = &_dcd_data.qtd[epnum][dir]; - - p_qhd->qtd_overlay.halted = false; // clear any previous error - p_qhd->qtd_overlay.next = (uint32_t) p_qtd; // link qtd to qhd - - // flush cache - CleanInvalidateDCache_by_Addr((uint32_t*) &_dcd_data, sizeof(dcd_data_t)); - - if ( epnum == 0 ) - { - // follows UM 24.10.8.1.1 Setup packet handling using setup lockout mechanism - // wait until ENDPTSETUPSTAT before priming data/status in response TODO add time out - while(dcd_reg->ENDPTSETUPSTAT & TU_BIT(0)) {} - } - - // start transfer - dcd_reg->ENDPTPRIME = TU_BIT(epnum + (dir ? 16 : 0)); -} - -bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes) -{ - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - dcd_qhd_t* p_qhd = &_dcd_data.qhd[epnum][dir]; - dcd_qtd_t* p_qtd = &_dcd_data.qtd[epnum][dir]; - - // Prepare qtd - qtd_init(p_qtd, buffer, total_bytes); - - // Start qhd transfer - p_qhd->ff = NULL; - qhd_start_xfer(rhport, epnum, dir); - - return true; -} - -// fifo has to be aligned to 4k boundary -bool dcd_edpt_xfer_fifo (uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16_t total_bytes) -{ - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - dcd_qhd_t * p_qhd = &_dcd_data.qhd[epnum][dir]; - dcd_qtd_t * p_qtd = &_dcd_data.qtd[epnum][dir]; - - tu_fifo_buffer_info_t fifo_info; - - if (dir) - { - tu_fifo_get_read_info(ff, &fifo_info); - } else - { - tu_fifo_get_write_info(ff, &fifo_info); - } - - if ( fifo_info.len_lin >= total_bytes ) - { - // Linear length is enough for this transfer - qtd_init(p_qtd, fifo_info.ptr_lin, total_bytes); - } - else - { - // linear part is not enough - - // prepare TD up to linear length - qtd_init(p_qtd, fifo_info.ptr_lin, fifo_info.len_lin); - - if ( !tu_offset4k((uint32_t) fifo_info.ptr_wrap) && !tu_offset4k(tu_fifo_depth(ff)) ) - { - // If buffer is aligned to 4K & buffer size is multiple of 4K - // We can make use of buffer page array to also combine the linear + wrapped length - p_qtd->total_bytes = p_qtd->expected_bytes = total_bytes; - - for(uint8_t i = 1, page = 0; i < 5; i++) - { - // pick up buffer array where linear ends - if (p_qtd->buffer[i] == 0) - { - p_qtd->buffer[i] = (uint32_t) fifo_info.ptr_wrap + 4096 * page; - page++; - } - } - - CleanInvalidateDCache_by_Addr((uint32_t*) tu_align((uint32_t) fifo_info.ptr_wrap, 4), total_bytes - fifo_info.len_wrap + 31); - } - else - { - // TODO we may need to carry the wrapped length after the linear part complete - // for now only transfer up to linear part - } - } - - // Start qhd transfer - p_qhd->ff = ff; - qhd_start_xfer(rhport, epnum, dir); - - return true; -} - -//--------------------------------------------------------------------+ -// ISR -//--------------------------------------------------------------------+ - -static void process_edpt_complete_isr(uint8_t rhport, uint8_t epnum, uint8_t dir) -{ - dcd_qhd_t * p_qhd = &_dcd_data.qhd[epnum][dir]; - dcd_qtd_t * p_qtd = &_dcd_data.qtd[epnum][dir]; - - uint8_t result = p_qtd->halted ? XFER_RESULT_STALLED : - ( p_qtd->xact_err || p_qtd->buffer_err ) ? XFER_RESULT_FAILED : XFER_RESULT_SUCCESS; - - if ( result != XFER_RESULT_SUCCESS ) - { - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - // flush to abort error buffer - dcd_reg->ENDPTFLUSH = TU_BIT(epnum + (dir ? 16 : 0)); - } - - uint16_t const xferred_bytes = p_qtd->expected_bytes - p_qtd->total_bytes; - - if (p_qhd->ff) - { - if (dir == TUSB_DIR_IN) - { - tu_fifo_advance_read_pointer(p_qhd->ff, xferred_bytes); - } else - { - tu_fifo_advance_write_pointer(p_qhd->ff, xferred_bytes); - } - } - - // only number of bytes in the IOC qtd - dcd_event_xfer_complete(rhport, tu_edpt_addr(epnum, dir), xferred_bytes, result, true); -} - -void dcd_int_handler(uint8_t rhport) -{ - dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - - uint32_t const int_enable = dcd_reg->USBINTR; - uint32_t const int_status = dcd_reg->USBSTS & int_enable; - dcd_reg->USBSTS = int_status; // Acknowledge handled interrupt - - // disabled interrupt sources - if (int_status == 0) return; - - // Set if the port controller enters the full or high-speed operational state. - // either from Bus Reset or Suspended state - if (int_status & INTR_PORT_CHANGE) - { - // TU_LOG2("PortChange %08lx\r\n", dcd_reg->PORTSC1); - - // Reset interrupt is not enabled, we manually check if Port Change is due - // to connection / disconnection - if ( dcd_reg->USBSTS & INTR_RESET ) - { - dcd_reg->USBSTS = INTR_RESET; - - if (dcd_reg->PORTSC1 & PORTSC1_CURRENT_CONNECT_STATUS) - { - uint32_t const speed = (dcd_reg->PORTSC1 & PORTSC1_PORT_SPEED) >> PORTSC1_PORT_SPEED_POS; - bus_reset(rhport); - dcd_event_bus_reset(rhport, (tusb_speed_t) speed, true); - }else - { - dcd_event_bus_signal(rhport, DCD_EVENT_UNPLUGGED, true); - } - } - else - { - // Triggered by resuming from suspended state - if ( !(dcd_reg->PORTSC1 & PORTSC1_SUSPEND) ) - { - dcd_event_bus_signal(rhport, DCD_EVENT_RESUME, true); - } - } - } - - if (int_status & INTR_SUSPEND) - { - // TU_LOG2("Suspend %08lx\r\n", dcd_reg->PORTSC1); - - if (dcd_reg->PORTSC1 & PORTSC1_SUSPEND) - { - // Note: Host may delay more than 3 ms before and/or after bus reset before doing enumeration. - // Skip suspend event if we are not addressed - if ((dcd_reg->DEVICEADDR >> 25) & 0x0f) - { - dcd_event_bus_signal(rhport, DCD_EVENT_SUSPEND, true); - } - } - } - - if (int_status & INTR_USB) - { - // Make sure we read the latest version of _dcd_data. - CleanInvalidateDCache_by_Addr((uint32_t*) &_dcd_data, sizeof(dcd_data_t)); - - uint32_t const edpt_complete = dcd_reg->ENDPTCOMPLETE; - dcd_reg->ENDPTCOMPLETE = edpt_complete; // acknowledge - - if (dcd_reg->ENDPTSETUPSTAT) - { - //------------- Set up Received -------------// - // 23.10.10.2 Operational model for setup transfers - dcd_reg->ENDPTSETUPSTAT = dcd_reg->ENDPTSETUPSTAT; - - dcd_event_setup_received(rhport, (uint8_t*)(uintptr_t) &_dcd_data.qhd[0][0].setup_request, true); - } - - // 23.10.12.3 Failed QTD also get ENDPTCOMPLETE set - // nothing to do, we will submit xfer as error to usbd - // if (int_status & INTR_ERROR) { } - - if ( edpt_complete ) - { - for(uint8_t epnum = 0; epnum < TUP_DCD_ENDPOINT_MAX; epnum++) - { - if ( tu_bit_test(edpt_complete, epnum) ) process_edpt_complete_isr(rhport, epnum, TUSB_DIR_OUT); - if ( tu_bit_test(edpt_complete, epnum+16) ) process_edpt_complete_isr(rhport, epnum, TUSB_DIR_IN); - } - } - } - - if (int_status & INTR_SOF) - { - dcd_event_bus_signal(rhport, DCD_EVENT_SOF, true); - } -} - -#endif diff --git a/src/portable/nxp/transdimension/hcd_transdimension.c b/src/portable/nxp/transdimension/hcd_transdimension.c deleted file mode 100644 index 0b3e9e4ef..000000000 --- a/src/portable/nxp/transdimension/hcd_transdimension.c +++ /dev/null @@ -1,119 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "tusb_option.h" - -// NXP Trans-Dimension USB IP implement EHCI for host functionality - -#if CFG_TUH_ENABLED && \ - (CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT) - -#warning "transdimenion is renamed to chipidea (portable/chipidea/ci_hs) to match other opensource naming convention such as linux. This file will be removed in the future, please update your makefile accordingly" - -//--------------------------------------------------------------------+ -// INCLUDE -//--------------------------------------------------------------------+ -#if CFG_TUSB_MCU == OPT_MCU_MIMXRT - #include "fsl_device_registers.h" -#else - // LPCOpen for 18xx & 43xx - #include "chip.h" -#endif - -#include "common/tusb_common.h" -#include "common_transdimension.h" -#include "portable/ehci/ehci_api.h" - -//--------------------------------------------------------------------+ -// MACRO CONSTANT TYPEDEF -//--------------------------------------------------------------------+ - -// TODO can be merged with dcd_controller_t -typedef struct -{ - uint32_t regs_base; // registers base - const IRQn_Type irqnum; // IRQ number -}hcd_controller_t; - -#if CFG_TUSB_MCU == OPT_MCU_MIMXRT - static const hcd_controller_t _hcd_controller[] = - { - // RT1010 and RT1020 only has 1 USB controller - #if FSL_FEATURE_SOC_USBHS_COUNT == 1 - { .regs_base = USB_BASE , .irqnum = USB_OTG1_IRQn } - #else - { .regs_base = USB1_BASE, .irqnum = USB_OTG1_IRQn }, - { .regs_base = USB2_BASE, .irqnum = USB_OTG2_IRQn } - #endif - }; - -#else - static const hcd_controller_t _hcd_controller[] = - { - { .regs_base = LPC_USB0_BASE, .irqnum = USB0_IRQn }, - { .regs_base = LPC_USB1_BASE, .irqnum = USB1_IRQn } - }; -#endif - -//--------------------------------------------------------------------+ -// Controller API -//--------------------------------------------------------------------+ - -bool hcd_init(uint8_t rhport) -{ - hcd_registers_t* hcd_reg = (hcd_registers_t*) _hcd_controller[rhport].regs_base; - - // Reset controller - hcd_reg->USBCMD |= USBCMD_RESET; - while( hcd_reg->USBCMD & USBCMD_RESET ) {} - - // Set mode to device, must be set immediately after reset -#if CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX - // LPC18XX/43XX need to set VBUS Power Select to HIGH - // RHPORT1 is fullspeed only (need external PHY for Highspeed) - hcd_reg->USBMODE = USBMODE_CM_HOST | USBMODE_VBUS_POWER_SELECT; - if (rhport == 1) hcd_reg->PORTSC1 |= PORTSC1_FORCE_FULL_SPEED; -#else - hcd_reg->USBMODE = USBMODE_CM_HOST; -#endif - - // FIXME force full speed, still have issue with Highspeed enumeration - hcd_reg->PORTSC1 |= PORTSC1_FORCE_FULL_SPEED; - - return ehci_init(rhport, (uint32_t) &hcd_reg->CAPLENGTH, (uint32_t) &hcd_reg->USBCMD); -} - -void hcd_int_enable(uint8_t rhport) -{ - NVIC_EnableIRQ(_hcd_controller[rhport].irqnum); -} - -void hcd_int_disable(uint8_t rhport) -{ - NVIC_DisableIRQ(_hcd_controller[rhport].irqnum); -} - -#endif -- cgit v1.3.1 From 8af8869d3bcb1504835ead4ba472cd922d997e8d Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 16 Jun 2023 11:26:38 +0700 Subject: renam OPT_MCU_MIMXRT to OPT_MCU_MIMXRT1XXX fix build util with makefile --- examples/host/bare_api/only.txt | 2 +- examples/host/cdc_msc_hid/only.txt | 2 +- examples/host/hid_controller/only.txt | 2 +- examples/host/msc_file_explorer/only.txt | 2 +- hw/bsp/board_mcu.h | 2 +- hw/bsp/f1c100s/README.md | 2 +- hw/bsp/imxrt/family.cmake | 4 ++-- hw/bsp/imxrt/family.mk | 2 +- src/class/audio/audio_device.c | 4 ++-- src/common/tusb_mcu.h | 2 +- src/portable/chipidea/ci_hs/dcd_ci_hs.c | 2 +- src/portable/chipidea/ci_hs/hcd_ci_hs.c | 5 ++--- src/tusb_option.h | 6 +++--- tools/build_utils.py | 7 +------ 14 files changed, 19 insertions(+), 25 deletions(-) (limited to 'src/portable') diff --git a/examples/host/bare_api/only.txt b/examples/host/bare_api/only.txt index fa9c14857..45da6c3f2 100644 --- a/examples/host/bare_api/only.txt +++ b/examples/host/bare_api/only.txt @@ -3,7 +3,7 @@ mcu:LPC177X_8X mcu:LPC18XX mcu:LPC40XX mcu:LPC43XX -mcu:MIMXRT +mcu:MIMXRT1XXX mcu:MIMXRT10XX mcu:MIMXRT11XX mcu:RP2040 diff --git a/examples/host/cdc_msc_hid/only.txt b/examples/host/cdc_msc_hid/only.txt index fa9c14857..45da6c3f2 100644 --- a/examples/host/cdc_msc_hid/only.txt +++ b/examples/host/cdc_msc_hid/only.txt @@ -3,7 +3,7 @@ mcu:LPC177X_8X mcu:LPC18XX mcu:LPC40XX mcu:LPC43XX -mcu:MIMXRT +mcu:MIMXRT1XXX mcu:MIMXRT10XX mcu:MIMXRT11XX mcu:RP2040 diff --git a/examples/host/hid_controller/only.txt b/examples/host/hid_controller/only.txt index fa9c14857..45da6c3f2 100644 --- a/examples/host/hid_controller/only.txt +++ b/examples/host/hid_controller/only.txt @@ -3,7 +3,7 @@ mcu:LPC177X_8X mcu:LPC18XX mcu:LPC40XX mcu:LPC43XX -mcu:MIMXRT +mcu:MIMXRT1XXX mcu:MIMXRT10XX mcu:MIMXRT11XX mcu:RP2040 diff --git a/examples/host/msc_file_explorer/only.txt b/examples/host/msc_file_explorer/only.txt index fa9c14857..45da6c3f2 100644 --- a/examples/host/msc_file_explorer/only.txt +++ b/examples/host/msc_file_explorer/only.txt @@ -3,7 +3,7 @@ mcu:LPC177X_8X mcu:LPC18XX mcu:LPC40XX mcu:LPC43XX -mcu:MIMXRT +mcu:MIMXRT1XXX mcu:MIMXRT10XX mcu:MIMXRT11XX mcu:RP2040 diff --git a/hw/bsp/board_mcu.h b/hw/bsp/board_mcu.h index edae4c645..ce2f919bf 100644 --- a/hw/bsp/board_mcu.h +++ b/hw/bsp/board_mcu.h @@ -116,7 +116,7 @@ #elif CFG_TUSB_MCU == OPT_MCU_VALENTYUSB_EPTRI // no header needed -#elif CFG_TUSB_MCU == OPT_MCU_MIMXRT +#elif CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX #include "fsl_device_registers.h" #elif CFG_TUSB_MCU == OPT_MCU_NUC120 diff --git a/hw/bsp/f1c100s/README.md b/hw/bsp/f1c100s/README.md index f7a863c34..86d454f8e 100644 --- a/hw/bsp/f1c100s/README.md +++ b/hw/bsp/f1c100s/README.md @@ -17,4 +17,4 @@ Flash: `make BOARD=f1c100s flash` will write the image to SPI flash, and then re ## TODO -* Add F1C100s to `#if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT` high speed MCU check in examples (maybe we should extract the logic?) +* Add F1C100s to `#if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX` high speed MCU check in examples (maybe we should extract the logic?) diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index f687fe833..c2c067141 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -14,7 +14,7 @@ include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) set(CMAKE_SYSTEM_PROCESSOR cortex-m7 CACHE INTERNAL "System Processor") set(CMAKE_TOOLCHAIN_FILE ${TOP}/tools/cmake/toolchain/arm_${TOOLCHAIN}.cmake) -set(FAMILY_MCUS MIMXRT CACHE INTERNAL "") +set(FAMILY_MCUS MIMXRT1XXX CACHE INTERNAL "") # enable LTO if supported include(CheckIPOSupported) @@ -119,7 +119,7 @@ function(family_configure_example TARGET) ) # Add TinyUSB - family_add_tinyusb(${TARGET} OPT_MCU_MIMXRT) + family_add_tinyusb(${TARGET} OPT_MCU_MIMXRT1XXX) # Link dependencies target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) diff --git a/hw/bsp/imxrt/family.mk b/hw/bsp/imxrt/family.mk index 0c297f060..c3a69e7c5 100644 --- a/hw/bsp/imxrt/family.mk +++ b/hw/bsp/imxrt/family.mk @@ -13,7 +13,7 @@ CFLAGS += \ -D__ARMVFP__=0 -D__ARMFPV5__=0\ -DXIP_EXTERNAL_FLASH=1 \ -DXIP_BOOT_HEADER_ENABLE=1 \ - -DCFG_TUSB_MCU=OPT_MCU_MIMXRT + -DCFG_TUSB_MCU=OPT_MCU_MIMXRT1XXX ifdef BOARD_TUD_RHPORT CFLAGS += -DBOARD_TUD_RHPORT=$(BOARD_TUD_RHPORT) diff --git a/src/class/audio/audio_device.c b/src/class/audio/audio_device.c index f487fe60e..e5dbe988a 100644 --- a/src/class/audio/audio_device.c +++ b/src/class/audio/audio_device.c @@ -66,7 +66,7 @@ // Use ring buffer if it's available, some MCUs need extra RAM requirements #ifndef TUD_AUDIO_PREFER_RING_BUFFER - #if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT + #if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX #define TUD_AUDIO_PREFER_RING_BUFFER 0 #else #define TUD_AUDIO_PREFER_RING_BUFFER 1 @@ -85,7 +85,7 @@ CFG_TUSB_MCU == OPT_MCU_RX72N || \ CFG_TUSB_MCU == OPT_MCU_LPC18XX || \ CFG_TUSB_MCU == OPT_MCU_LPC43XX || \ - CFG_TUSB_MCU == OPT_MCU_MIMXRT || \ + CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX || \ CFG_TUSB_MCU == OPT_MCU_MSP432E4 #if TUD_AUDIO_PREFER_RING_BUFFER #define USE_LINEAR_BUFFER 0 diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 485d6168d..56525725e 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -90,7 +90,7 @@ #define TUP_DCD_ENDPOINT_MAX 8 #define TUP_RHPORT_HIGHSPEED 1 -#elif TU_CHECK_MCU(OPT_MCU_MIMXRT) +#elif TU_CHECK_MCU(OPT_MCU_MIMXRT1XXX) #define TUP_USBIP_CHIPIDEA_HS #define TUP_USBIP_EHCI diff --git a/src/portable/chipidea/ci_hs/dcd_ci_hs.c b/src/portable/chipidea/ci_hs/dcd_ci_hs.c index 850c82e43..588e761a9 100644 --- a/src/portable/chipidea/ci_hs/dcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/dcd_ci_hs.c @@ -31,7 +31,7 @@ #include "device/dcd.h" #include "ci_hs_type.h" -#if CFG_TUSB_MCU == OPT_MCU_MIMXRT +#if CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX #include "ci_hs_imxrt.h" void dcd_dcache_clean(void* addr, uint32_t data_size) { diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index 8c27abbf6..0f095147d 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -28,8 +28,7 @@ // Chipidea Highspeed USB IP implement EHCI for host functionality -#if CFG_TUH_ENABLED && \ - (CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT) +#if CFG_TUH_ENABLED && defined(TUP_USBIP_EHCI) //--------------------------------------------------------------------+ // INCLUDE @@ -39,7 +38,7 @@ #include "portable/ehci/ehci_api.h" #include "ci_hs_type.h" -#if CFG_TUSB_MCU == OPT_MCU_MIMXRT +#if CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX #include "ci_hs_imxrt.h" void hcd_dcache_clean(void* addr, uint32_t data_size) { diff --git a/src/tusb_option.h b/src/tusb_option.h index bb669e693..43e67cf64 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -97,9 +97,9 @@ #define OPT_MCU_VALENTYUSB_EPTRI 600 ///< Fomu eptri config // NXP iMX RT -#define OPT_MCU_MIMXRT 700 ///< NXP iMX RT Series -#define OPT_MCU_MIMXRT10XX OPT_MCU_MIMXRT ///< RT10xx -#define OPT_MCU_MIMXRT11XX OPT_MCU_MIMXRT ///< RT11xx +#define OPT_MCU_MIMXRT1XXX 700 ///< NXP iMX RT1xxx Series +#define OPT_MCU_MIMXRT10XX OPT_MCU_MIMXRT1XXX ///< RT10xx +#define OPT_MCU_MIMXRT11XX OPT_MCU_MIMXRT1XXX ///< RT11xx // Nuvoton #define OPT_MCU_NUC121 800 diff --git a/tools/build_utils.py b/tools/build_utils.py index 6f907729b..5d735bc17 100644 --- a/tools/build_utils.py +++ b/tools/build_utils.py @@ -30,13 +30,8 @@ def skip_example(example, board): family_dir = board_dir.parent.parent family = family_dir.name - # family CMake - family_mk = family_dir / "family.cmake" - # family.mk - if not family_mk.exists(): - family_mk = family_dir / "family.mk" - + family_mk = family_dir / "family.mk" mk_contents = family_mk.read_text() # Find the mcu, first in family mk then board mk -- cgit v1.3.1 From 65d6acdbfaea84c3274e359acd5e5474f04e8851 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 16 Jun 2023 12:02:42 +0700 Subject: fix build warnings --- hw/bsp/family_support.cmake | 2 ++ hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h | 11 +++++------ hw/bsp/imxrt/family.cmake | 12 ++++++++---- src/device/dcd.h | 6 +++--- src/host/hcd.h | 6 +++--- src/portable/chipidea/ci_hs/ci_hs_imxrt.h | 23 +++++++++++++---------- src/portable/chipidea/ci_hs/dcd_ci_hs.c | 12 ++++++------ src/portable/chipidea/ci_hs/hcd_ci_hs.c | 6 +++--- src/portable/ehci/ehci.c | 8 ++++---- 9 files changed, 47 insertions(+), 39 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index dfc2095e5..02040c4ed 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -177,6 +177,8 @@ function(family_add_freertos TARGET) target_include_directories(freertos_config INTERFACE ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/${FAMILY}/FreeRTOSConfig ) + # add board definition to freertos_config mostly for SystemCoreClock + target_link_libraries(freertos_config INTERFACE board_${BOARD}) endif() # freertos kernel should be generic as freertos_config however, CMAKE complains with missing variable diff --git a/hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h index c1928fbcd..f95927069 100644 --- a/hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h +++ b/hw/bsp/imxrt/FreeRTOSConfig/FreeRTOSConfig.h @@ -44,15 +44,14 @@ // skip if included from IAR assembler #ifndef __IASMARM__ -// FIXME cause redundant-decls warnings -extern uint32_t SystemCoreClock; + #include "fsl_device_registers.h" #endif /* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 1 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) #define configUSE_PREEMPTION 1 #define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index c2c067141..fc90b7e80 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -103,10 +103,6 @@ function(family_configure_example TARGET) #---------- Port Specific ---------- # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC - # TinyUSB Port - ${TOP}/src/portable/chipidea/ci_hs/dcd_ci_hs.c - ${TOP}/src/portable/chipidea/ci_hs/hcd_ci_hs.c - ${TOP}/src/portable/ehci/ehci.c # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c @@ -121,6 +117,14 @@ function(family_configure_example TARGET) # Add TinyUSB family_add_tinyusb(${TARGET} OPT_MCU_MIMXRT1XXX) + # Add TinyUSB Port source + target_sources(${TARGET}-tinyusb PUBLIC + ${TOP}/src/portable/chipidea/ci_hs/dcd_ci_hs.c + ${TOP}/src/portable/chipidea/ci_hs/hcd_ci_hs.c + ${TOP}/src/portable/ehci/ehci.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) + # Link dependencies target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) diff --git a/src/device/dcd.h b/src/device/dcd.h index 4e9cfd5d5..18a708347 100644 --- a/src/device/dcd.h +++ b/src/device/dcd.h @@ -108,15 +108,15 @@ typedef struct TU_ATTR_ALIGNED(4) // clean/flush data cache: write cache -> memory. // Required before an DMA TX transfer to make sure data is in memory -void dcd_dcache_clean(void* addr, uint32_t data_size) TU_ATTR_WEAK; +void dcd_dcache_clean(void const* addr, uint32_t data_size) TU_ATTR_WEAK; // invalidate data cache: mark cache as invalid, next read will read from memory // Required BOTH before and after an DMA RX transfer -void dcd_dcache_invalidate(void* addr, uint32_t data_size) TU_ATTR_WEAK; +void dcd_dcache_invalidate(void const* addr, uint32_t data_size) TU_ATTR_WEAK; // clean and invalidate data cache // Required before an DMA transfer where memory is both read/write by DMA -void dcd_dcache_clean_invalidate(void* addr, uint32_t data_size) TU_ATTR_WEAK; +void dcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) TU_ATTR_WEAK; //--------------------------------------------------------------------+ // Controller API diff --git a/src/host/hcd.h b/src/host/hcd.h index 5a3b0a087..3355c18b2 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -110,15 +110,15 @@ typedef struct // clean/flush data cache: write cache -> memory. // Required before an DMA TX transfer to make sure data is in memory -void hcd_dcache_clean(void* addr, uint32_t data_size) TU_ATTR_WEAK; +void hcd_dcache_clean(void const* addr, uint32_t data_size) TU_ATTR_WEAK; // invalidate data cache: mark cache as invalid, next read will read from memory // Required BOTH before and after an DMA RX transfer -void hcd_dcache_invalidate(void* addr, uint32_t data_size) TU_ATTR_WEAK; +void hcd_dcache_invalidate(void const* addr, uint32_t data_size) TU_ATTR_WEAK; // clean and invalidate data cache // Required before an DMA transfer where memory is both read/write by DMA -void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) TU_ATTR_WEAK; +void hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) TU_ATTR_WEAK; //--------------------------------------------------------------------+ // Controller API diff --git a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h index ceff893bd..c14f00431 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h +++ b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h @@ -64,25 +64,28 @@ static const ci_hs_controller_t _ci_controller[] = #define CI_HCD_INT_DISABLE(_p) NVIC_DisableIRQ(_ci_controller[_p].irqnum) //------------- DCache -------------// -TU_ATTR_ALWAYS_INLINE static inline bool imxrt_is_cache_mem(uint32_t addr) { +TU_ATTR_ALWAYS_INLINE static inline bool imxrt_is_cache_mem(uintptr_t addr) { return !(0x20000000 <= addr && addr < 0x20100000); } -TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_clean(void* addr, uint32_t data_size) { - if (imxrt_is_cache_mem((uint32_t) addr)) { - SCB_CleanDCache_by_Addr((uint32_t *) addr, (int32_t) data_size); +TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_clean(void const* addr, uint32_t data_size) { + const uintptr_t addr32 = (uintptr_t) addr; + if (imxrt_is_cache_mem(addr32)) { + SCB_CleanDCache_by_Addr((uint32_t *) addr32, (int32_t) data_size); } } -TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_invalidate(void* addr, uint32_t data_size) { - if (imxrt_is_cache_mem((uint32_t) addr)) { - SCB_InvalidateDCache_by_Addr(addr, (int32_t) data_size); +TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_invalidate(void const* addr, uint32_t data_size) { + const uintptr_t addr32 = (uintptr_t) addr; + if (imxrt_is_cache_mem(addr32)) { + SCB_InvalidateDCache_by_Addr((void*) addr32, (int32_t) data_size); } } -TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_clean_invalidate(void* addr, uint32_t data_size) { - if (imxrt_is_cache_mem((uint32_t) addr)) { - SCB_CleanInvalidateDCache_by_Addr(addr, (int32_t) data_size); +TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_clean_invalidate(void const* addr, uint32_t data_size) { + const uintptr_t addr32 = (uintptr_t) addr; + if (imxrt_is_cache_mem(addr32)) { + SCB_CleanInvalidateDCache_by_Addr((uint32_t *) addr32, (int32_t) data_size); } } diff --git a/src/portable/chipidea/ci_hs/dcd_ci_hs.c b/src/portable/chipidea/ci_hs/dcd_ci_hs.c index 588e761a9..f50550d33 100644 --- a/src/portable/chipidea/ci_hs/dcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/dcd_ci_hs.c @@ -34,15 +34,15 @@ #if CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX #include "ci_hs_imxrt.h" - void dcd_dcache_clean(void* addr, uint32_t data_size) { + void dcd_dcache_clean(void const* addr, uint32_t data_size) { imxrt_dcache_clean(addr, data_size); } - void dcd_dcache_invalidate(void* addr, uint32_t data_size) { + void dcd_dcache_invalidate(void const* addr, uint32_t data_size) { imxrt_dcache_invalidate(addr, data_size); } - void dcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { + void dcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { imxrt_dcache_clean_invalidate(addr, data_size); } @@ -58,15 +58,15 @@ #error "Unsupported MCUs" #endif - TU_ATTR_WEAK void dcd_dcache_clean(void* addr, uint32_t data_size) { + TU_ATTR_WEAK void dcd_dcache_clean(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } - TU_ATTR_WEAK void dcd_dcache_invalidate(void* addr, uint32_t data_size) { + TU_ATTR_WEAK void dcd_dcache_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } - TU_ATTR_WEAK void dcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { + TU_ATTR_WEAK void dcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } #endif diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index 0f095147d..56167b8f6 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -41,15 +41,15 @@ #if CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX #include "ci_hs_imxrt.h" - void hcd_dcache_clean(void* addr, uint32_t data_size) { + void hcd_dcache_clean(void const* addr, uint32_t data_size) { imxrt_dcache_clean(addr, data_size); } - void hcd_dcache_invalidate(void* addr, uint32_t data_size) { + void hcd_dcache_invalidate(void const* addr, uint32_t data_size) { imxrt_dcache_invalidate(addr, data_size); } - void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { + void hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { imxrt_dcache_clean_invalidate(addr, data_size); } diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 2b25eee9d..38711e382 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -162,15 +162,15 @@ static void qtd_init (ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes) static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t new_type); static inline ehci_link_t* list_next (ehci_link_t const *p_link); -TU_ATTR_WEAK void hcd_dcache_clean(void* addr, uint32_t data_size) { +TU_ATTR_WEAK void hcd_dcache_clean(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } -TU_ATTR_WEAK void hcd_dcache_invalidate(void* addr, uint32_t data_size) { +TU_ATTR_WEAK void hcd_dcache_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } -TU_ATTR_WEAK void hcd_dcache_clean_invalidate(void* addr, uint32_t data_size) { +TU_ATTR_WEAK void hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } @@ -461,7 +461,7 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet qtd_init(td, setup_packet, 8); td->pid = EHCI_PID_SETUP; - hcd_dcache_clean((void *) setup_packet, 8); + hcd_dcache_clean(setup_packet, 8); // attach TD to QHD -> start transferring qhd_attach_qtd(qhd, td); -- cgit v1.3.1 From a7f330fa94b7a39858f6d770737451b51f061c25 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 16 Jun 2023 14:17:25 +0700 Subject: fix build, update freertos config for cmake --- examples/device/net_lwip_webserver/skip.txt | 2 +- hw/bsp/family_support.cmake | 8 ++------ hw/bsp/imxrt/family.cmake | 4 +--- hw/bsp/kinetis_kl/FreeRTOSConfig/FreeRTOSConfig.h | 11 +++++------ hw/bsp/kinetis_kl/boards/frdm_kl25z/clock_config.c | 2 +- hw/bsp/kinetis_kl/family.cmake | 10 ++++++---- hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h | 13 ++++++------- hw/bsp/lpc18/family.cmake | 12 +++++++----- hw/bsp/lpc55/FreeRTOSConfig/FreeRTOSConfig.h | 13 ++++++------- hw/bsp/lpc55/family.cmake | 20 ++++++-------------- hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h | 13 ++++++------- hw/bsp/mcx/family.cmake | 9 ++++++--- hw/bsp/nrf/FreeRTOSConfig/FreeRTOSConfig.h | 13 ++++++------- hw/bsp/nrf/boards/pca10095/board.cmake | 2 +- hw/bsp/nrf/family.cmake | 10 +++++++--- hw/bsp/stm32g0/FreeRTOSConfig/FreeRTOSConfig.h | 13 ++++++------- hw/bsp/stm32g0/family.cmake | 11 ++++++----- hw/bsp/stm32g4/FreeRTOSConfig/FreeRTOSConfig.h | 13 ++++++------- hw/bsp/stm32g4/family.cmake | 10 ++++++---- src/portable/nordic/nrf5x/dcd_nrf5x.c | 14 ++++++++++++++ src/portable/st/typec/typec_stm32.c | 4 ++-- 21 files changed, 107 insertions(+), 100 deletions(-) (limited to 'src/portable') diff --git a/examples/device/net_lwip_webserver/skip.txt b/examples/device/net_lwip_webserver/skip.txt index 77c7ec63a..e3a726a2b 100644 --- a/examples/device/net_lwip_webserver/skip.txt +++ b/examples/device/net_lwip_webserver/skip.txt @@ -4,7 +4,7 @@ mcu:MSP430x5xx mcu:NUC121 mcu:SAMD11 mcu:STM32L0 -mcu:MKL25ZXX +mcu:KINETIS_KL family:broadcom_64bit family:broadcom_32bit board:curiosity_nano diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index 02040c4ed..0132ef629 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -192,12 +192,8 @@ function(family_add_freertos TARGET) CFG_TUSB_OS=OPT_OS_FREERTOS ) # link tinyusb with freeRTOS kernel - target_link_libraries(${TARGET}-tinyusb PUBLIC - freertos_kernel - ) - target_link_libraries(${TARGET} PUBLIC - freertos_kernel - ) + target_link_libraries(${TARGET}-tinyusb PUBLIC freertos_kernel) + target_link_libraries(${TARGET} PUBLIC freertos_kernel) endfunction() diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index fc90b7e80..4a9842cf9 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -114,10 +114,8 @@ function(family_configure_example TARGET) ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} ) - # Add TinyUSB + # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_MIMXRT1XXX) - - # Add TinyUSB Port source target_sources(${TARGET}-tinyusb PUBLIC ${TOP}/src/portable/chipidea/ci_hs/dcd_ci_hs.c ${TOP}/src/portable/chipidea/ci_hs/hcd_ci_hs.c diff --git a/hw/bsp/kinetis_kl/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/kinetis_kl/FreeRTOSConfig/FreeRTOSConfig.h index 960bb23e1..a46af1759 100644 --- a/hw/bsp/kinetis_kl/FreeRTOSConfig/FreeRTOSConfig.h +++ b/hw/bsp/kinetis_kl/FreeRTOSConfig/FreeRTOSConfig.h @@ -44,15 +44,14 @@ // skip if included from IAR assembler #ifndef __IASMARM__ -// FIXME cause redundant-decls warnings -extern uint32_t SystemCoreClock; + #include "fsl_device_registers.h" #endif /* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 1 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) #define configUSE_PREEMPTION 1 #define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 diff --git a/hw/bsp/kinetis_kl/boards/frdm_kl25z/clock_config.c b/hw/bsp/kinetis_kl/boards/frdm_kl25z/clock_config.c index 1ba35e0dc..deabe25aa 100644 --- a/hw/bsp/kinetis_kl/boards/frdm_kl25z/clock_config.c +++ b/hw/bsp/kinetis_kl/boards/frdm_kl25z/clock_config.c @@ -83,7 +83,7 @@ board: FRDM-KL25Z * Variables ******************************************************************************/ /* System clock frequency. */ -extern uint32_t SystemCoreClock; +//extern uint32_t SystemCoreClock; /******************************************************************************* * Code diff --git a/hw/bsp/kinetis_kl/family.cmake b/hw/bsp/kinetis_kl/family.cmake index f491b3dee..5d4165185 100644 --- a/hw/bsp/kinetis_kl/family.cmake +++ b/hw/bsp/kinetis_kl/family.cmake @@ -87,9 +87,6 @@ function(family_configure_example TARGET) #---------- Port Specific ---------- # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC - # TinyUSB Port - ${TOP}/src/portable/chipidea/ci_fs/dcd_ci_fs.c - ${TOP}/src/portable/nxp/khci/hcd_khci.c # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c @@ -101,8 +98,13 @@ function(family_configure_example TARGET) ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} ) - # Add TinyUSB + # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_KINETIS_KL) + target_sources(${TARGET}-tinyusb PUBLIC + ${TOP}/src/portable/chipidea/ci_fs/dcd_ci_fs.c + ${TOP}/src/portable/nxp/khci/hcd_khci.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) # Link dependencies target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) diff --git a/hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h index 323c1a0a4..1b3c64e0b 100644 --- a/hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h +++ b/hw/bsp/lpc18/FreeRTOSConfig/FreeRTOSConfig.h @@ -42,17 +42,16 @@ * See http://www.freertos.org/a00110.html. *----------------------------------------------------------*/ -// IAR assembler have limited preprocessor support and it only need following macros: +// skip if included from IAR assembler #ifndef __IASMARM__ -// FIXME cause redundant-decls warnings -extern uint32_t SystemCoreClock; + #include "chip.h" #endif /* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 0 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) #define configUSE_PREEMPTION 1 #define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 diff --git a/hw/bsp/lpc18/family.cmake b/hw/bsp/lpc18/family.cmake index bcdec9c01..4e6e2b56d 100644 --- a/hw/bsp/lpc18/family.cmake +++ b/hw/bsp/lpc18/family.cmake @@ -79,10 +79,6 @@ function(family_configure_example TARGET) #---------- Port Specific ---------- # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC - # TinyUSB Port - ${TOP}/src/portable/chipidea/ci_hs/dcd_ci_hs.c - ${TOP}/src/portable/chipidea/ci_hs/hcd_ci_hs.c - ${TOP}/src/portable/ehci/ehci.c # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c @@ -94,8 +90,14 @@ function(family_configure_example TARGET) ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} ) - # Add TinyUSB + # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_LPC18XX) + target_sources(${TARGET}-tinyusb PUBLIC + ${TOP}/src/portable/chipidea/ci_hs/dcd_ci_hs.c + ${TOP}/src/portable/chipidea/ci_hs/hcd_ci_hs.c + ${TOP}/src/portable/ehci/ehci.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) # Link dependencies target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) diff --git a/hw/bsp/lpc55/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/lpc55/FreeRTOSConfig/FreeRTOSConfig.h index 421106f08..b1cef793e 100644 --- a/hw/bsp/lpc55/FreeRTOSConfig/FreeRTOSConfig.h +++ b/hw/bsp/lpc55/FreeRTOSConfig/FreeRTOSConfig.h @@ -42,17 +42,16 @@ * See http://www.freertos.org/a00110.html. *----------------------------------------------------------*/ -// IAR assembler have limited preprocessor support and it only need following macros: +// skip if included from IAR assembler #ifndef __IASMARM__ -// FIXME cause redundant-decls warnings -extern uint32_t SystemCoreClock; + #include "fsl_device_registers.h" #endif /* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 1 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) #define configUSE_PREEMPTION 1 #define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 diff --git a/hw/bsp/lpc55/family.cmake b/hw/bsp/lpc55/family.cmake index 22a09ce10..43fbe8638 100644 --- a/hw/bsp/lpc55/family.cmake +++ b/hw/bsp/lpc55/family.cmake @@ -16,16 +16,6 @@ set(FAMILY_MCUS LPC55XX CACHE INTERNAL "") # include board specific include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) -#------------------------------------ -# freertos -#------------------------------------ -if (NOT TARGET freertos_config) - add_library(freertos_config INTERFACE) - target_include_directories(freertos_config SYSTEM INTERFACE - ${CMAKE_CURRENT_LIST_DIR}/FreeRTOSConfig - ) -endif() - #------------------------------------ # BOARD_TARGET @@ -106,8 +96,6 @@ function(family_configure_example TARGET) #---------- Port Specific ---------- # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC - # TinyUSB Port - ${TOP}/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c @@ -121,15 +109,19 @@ function(family_configure_example TARGET) ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} ) - # Add TinyUSB + # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_LPC55XX) + target_sources(${TARGET}-tinyusb PUBLIC + ${TOP}/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) # Link dependencies target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) # Flashing family_flash_jlink(${TARGET}) - family_flash_nxplink(${TARGET}) + #family_flash_nxplink(${TARGET}) #family_flash_pyocd(${TARGET}) endfunction() diff --git a/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h index 421106f08..b1cef793e 100644 --- a/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h +++ b/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h @@ -42,17 +42,16 @@ * See http://www.freertos.org/a00110.html. *----------------------------------------------------------*/ -// IAR assembler have limited preprocessor support and it only need following macros: +// skip if included from IAR assembler #ifndef __IASMARM__ -// FIXME cause redundant-decls warnings -extern uint32_t SystemCoreClock; + #include "fsl_device_registers.h" #endif /* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 1 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) #define configUSE_PREEMPTION 1 #define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 diff --git a/hw/bsp/mcx/family.cmake b/hw/bsp/mcx/family.cmake index 7c5feaecf..83f44222b 100644 --- a/hw/bsp/mcx/family.cmake +++ b/hw/bsp/mcx/family.cmake @@ -88,8 +88,6 @@ function(family_configure_example TARGET) #---------- Port Specific ---------- # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC - # TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS - ${TOP}/src/portable/chipidea/$ # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c @@ -101,8 +99,13 @@ function(family_configure_example TARGET) ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} ) - # Add TinyUSB + # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_MCXN9) + target_sources(${TARGET}-tinyusb PUBLIC + # TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS + ${TOP}/src/portable/chipidea/$ + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) # Link dependencies target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) diff --git a/hw/bsp/nrf/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/nrf/FreeRTOSConfig/FreeRTOSConfig.h index 421106f08..a56f243ea 100644 --- a/hw/bsp/nrf/FreeRTOSConfig/FreeRTOSConfig.h +++ b/hw/bsp/nrf/FreeRTOSConfig/FreeRTOSConfig.h @@ -42,17 +42,16 @@ * See http://www.freertos.org/a00110.html. *----------------------------------------------------------*/ -// IAR assembler have limited preprocessor support and it only need following macros: +// skip if included from IAR assembler #ifndef __IASMARM__ -// FIXME cause redundant-decls warnings -extern uint32_t SystemCoreClock; + #include "nrf.h" #endif /* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 1 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) #define configUSE_PREEMPTION 1 #define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 diff --git a/hw/bsp/nrf/boards/pca10095/board.cmake b/hw/bsp/nrf/boards/pca10095/board.cmake index 1eb8ad4f1..1e72243c9 100644 --- a/hw/bsp/nrf/boards/pca10095/board.cmake +++ b/hw/bsp/nrf/boards/pca10095/board.cmake @@ -6,7 +6,7 @@ function(update_board TARGET) NRF5340_XXAA NRF5340_XXAA_APPLICATION ) - target_sources(${TARGET} PUBLIC + target_sources(${TARGET} PRIVATE ${NRFX_DIR}/drivers/src/nrfx_usbreg.c ) endfunction() diff --git a/hw/bsp/nrf/family.cmake b/hw/bsp/nrf/family.cmake index 7faeaf6cb..88670b50b 100644 --- a/hw/bsp/nrf/family.cmake +++ b/hw/bsp/nrf/family.cmake @@ -100,8 +100,6 @@ function(family_configure_example TARGET) #---------- Port Specific ---------- # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC - # TinyUSB Port - ${TOP}/src/portable/nordic/nrf5x/dcd_nrf5x.c # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c @@ -113,8 +111,14 @@ function(family_configure_example TARGET) ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} ) - # Add TinyUSB + # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_NRF5X) + target_sources(${TARGET}-tinyusb PUBLIC + ${TOP}/src/portable/nordic/nrf5x/dcd_nrf5x.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) + + # Link dependencies target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) diff --git a/hw/bsp/stm32g0/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/stm32g0/FreeRTOSConfig/FreeRTOSConfig.h index 1758efcf2..c8736f6d1 100644 --- a/hw/bsp/stm32g0/FreeRTOSConfig/FreeRTOSConfig.h +++ b/hw/bsp/stm32g0/FreeRTOSConfig/FreeRTOSConfig.h @@ -42,17 +42,16 @@ * See http://www.freertos.org/a00110.html. *----------------------------------------------------------*/ -// IAR assembler have limited preprocessor support and it only need following macros: +// skip if included from IAR assembler #ifndef __IASMARM__ -// FIXME cause redundant-decls warnings -extern uint32_t SystemCoreClock; + #include "stm32g0xx.h" #endif /* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 0 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) #define configUSE_PREEMPTION 1 #define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 diff --git a/hw/bsp/stm32g0/family.cmake b/hw/bsp/stm32g0/family.cmake index 988033070..1381eaa5f 100644 --- a/hw/bsp/stm32g0/family.cmake +++ b/hw/bsp/stm32g0/family.cmake @@ -59,8 +59,6 @@ function(add_board_target BOARD_TARGET) update_board(${BOARD_TARGET}) - cmake_print_variables(CMAKE_C_COMPILER_ID) - if (CMAKE_C_COMPILER_ID STREQUAL "GNU") target_link_options(${BOARD_TARGET} PUBLIC "LINKER:--script=${LD_FILE_GNU}" @@ -90,8 +88,6 @@ function(family_configure_example TARGET) #---------- Port Specific ---------- # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC - # TinyUSB Port - ${TOP}/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c @@ -103,8 +99,13 @@ function(family_configure_example TARGET) ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} ) - # Add TinyUSB + # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_STM32G0) + target_sources(${TARGET}-tinyusb PUBLIC + ${TOP}/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c + ${TOP}/src/portable/st/typec/typec_stm32.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) # Link dependencies target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) diff --git a/hw/bsp/stm32g4/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/stm32g4/FreeRTOSConfig/FreeRTOSConfig.h index 7974434d3..95fcbb08a 100644 --- a/hw/bsp/stm32g4/FreeRTOSConfig/FreeRTOSConfig.h +++ b/hw/bsp/stm32g4/FreeRTOSConfig/FreeRTOSConfig.h @@ -42,17 +42,16 @@ * See http://www.freertos.org/a00110.html. *----------------------------------------------------------*/ -// IAR assembler have limited preprocessor support and it only need following macros: +// skip if included from IAR assembler #ifndef __IASMARM__ -// FIXME cause redundant-decls warnings -extern uint32_t SystemCoreClock; + #include "stm32g4xx.h" #endif /* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 0 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) #define configUSE_PREEMPTION 1 #define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 diff --git a/hw/bsp/stm32g4/family.cmake b/hw/bsp/stm32g4/family.cmake index 618563f66..45525c744 100644 --- a/hw/bsp/stm32g4/family.cmake +++ b/hw/bsp/stm32g4/family.cmake @@ -88,9 +88,6 @@ function(family_configure_example TARGET) #---------- Port Specific ---------- # These files are built for each example since it depends on example's tusb_config.h target_sources(${TARGET} PUBLIC - # TinyUSB Port - ${TOP}/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c - ${TOP}/src/portable/st/typec/typec_stm32.c # BSP ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c @@ -102,8 +99,13 @@ function(family_configure_example TARGET) ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} ) - # Add TinyUSB + # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_STM32G4) + target_sources(${TARGET}-tinyusb PUBLIC + ${TOP}/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c + ${TOP}/src/portable/st/typec/typec_stm32.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) # Link dependencies target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) diff --git a/src/portable/nordic/nrf5x/dcd_nrf5x.c b/src/portable/nordic/nrf5x/dcd_nrf5x.c index eee5686f4..acc967bb3 100644 --- a/src/portable/nordic/nrf5x/dcd_nrf5x.c +++ b/src/portable/nordic/nrf5x/dcd_nrf5x.c @@ -29,10 +29,24 @@ #if CFG_TUD_ENABLED && CFG_TUSB_MCU == OPT_MCU_NRF5X #include + +// Suppress warning caused by nrfx driver +#ifdef __GNUC__ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wcast-qual" +#pragma GCC diagnostic ignored "-Wcast-align" +#pragma GCC diagnostic ignored "-Wunused-parameter" +#endif + #include "nrf.h" #include "nrf_clock.h" #include "nrf_power.h" #include "nrfx_usbd_errata.h" + +#ifdef __GNUC__ +#pragma GCC diagnostic pop +#endif + #include "device/dcd.h" // TODO remove later diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index b09dc5bae..231da5450 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -186,7 +186,7 @@ bool tcd_init(uint8_t rhport, uint32_t port_type) { v_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; v_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; - TU_LOG1("Initial VState CC1 = %u, CC2 = %u\r\n", v_cc[0], v_cc[1]); + TU_LOG1("Initial VState CC1 = %lu, CC2 = %lu\r\n", v_cc[0], v_cc[1]); // Enable CC1 & CC2 Interrupt UCPD1->IMR = UCPD_IMR_TYPECEVT1IE | UCPD_IMR_TYPECEVT2IE; @@ -246,7 +246,7 @@ void tcd_int_handler(uint8_t rhport) { v_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; v_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; - TU_LOG3("VState CC1 = %u, CC2 = %u\n", v_cc[0], v_cc[1]); + TU_LOG3("VState CC1 = %lu, CC2 = %lu\n", v_cc[0], v_cc[1]); uint32_t cr = UCPD1->CR; -- cgit v1.3.1 From e754795d3adec4bc3a66a4131d0662d87acb4893 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 16 Jun 2023 15:29:34 +0700 Subject: fix build warnings --- .github/workflows/build_iar.yml | 2 +- examples/device/audio_test_multi_rate/src/main.c | 2 +- examples/host/msc_file_explorer/CMakeLists.txt | 7 ++++++ examples/rules.mk | 1 + examples/typec/power_delivery/src/main.c | 4 +--- hw/bsp/family_support.cmake | 29 ++++++++++++++++++++++++ hw/bsp/imxrt/family.c | 11 +++++++++ hw/bsp/lpc55/family.cmake | 1 + hw/bsp/nrf/family.c | 14 ++++++++++++ hw/bsp/stm32g4/family.mk | 1 + src/portable/st/typec/typec_stm32.c | 9 +++++--- tools/cmake/toolchain/arm_gcc.cmake | 26 --------------------- tools/cmake/toolchain/arm_iar.cmake | 3 --- 13 files changed, 73 insertions(+), 37 deletions(-) (limited to 'src/portable') diff --git a/.github/workflows/build_iar.yml b/.github/workflows/build_iar.yml index 83e81164a..7e42a66f8 100644 --- a/.github/workflows/build_iar.yml +++ b/.github/workflows/build_iar.yml @@ -32,7 +32,7 @@ jobs: # Alphabetical order # Note: bundle multiple families into a matrix since there is only one self-hosted instance can # run IAR build. Too many matrix can hurt due to setup/teardown overhead. - - 'stm32f0 stm32f1 stm32f4 stm32f7 stm32g4 stm32h7 stm32l4' + - 'stm32f0 stm32f1 stm32f7 stm32h7 stm32l4' steps: - name: Clean workspace run: | diff --git a/examples/device/audio_test_multi_rate/src/main.c b/examples/device/audio_test_multi_rate/src/main.c index 4dd53dd34..078e783eb 100644 --- a/examples/device/audio_test_multi_rate/src/main.c +++ b/examples/device/audio_test_multi_rate/src/main.c @@ -268,7 +268,7 @@ bool tud_audio_set_req_entity_cb(uint8_t rhport, tusb_control_request_t const * sampFreq = (uint32_t)((audio_control_cur_4_t *)pBuff)->bCur; - TU_LOG2("Clock set current freq: %d\r\n", sampFreq); + TU_LOG2("Clock set current freq: %lu\r\n", sampFreq); return true; break; diff --git a/examples/host/msc_file_explorer/CMakeLists.txt b/examples/host/msc_file_explorer/CMakeLists.txt index 2d5600059..327d1218a 100644 --- a/examples/host/msc_file_explorer/CMakeLists.txt +++ b/examples/host/msc_file_explorer/CMakeLists.txt @@ -21,6 +21,13 @@ target_sources(${PROJECT} PUBLIC ${TOP}/lib/fatfs/source/ffunicode.c ) +# Suppress warnings on fatfs +set_source_files_properties( + ${TOP}/lib/fatfs/source/ff.c + PROPERTIES + COMPILE_FLAGS "-Wno-conversion -Wno-cast-qual" +) + # Example include target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src diff --git a/examples/rules.mk b/examples/rules.mk index f6422092a..5727ab7e3 100644 --- a/examples/rules.mk +++ b/examples/rules.mk @@ -28,6 +28,7 @@ SRC_C += \ src/common/tusb_fifo.c \ src/device/usbd.c \ src/device/usbd_control.c \ + src/typec/usbc.c \ src/class/audio/audio_device.c \ src/class/cdc/cdc_device.c \ src/class/dfu/dfu_device.c \ diff --git a/examples/typec/power_delivery/src/main.c b/examples/typec/power_delivery/src/main.c index 342a2235f..08590aa74 100644 --- a/examples/typec/power_delivery/src/main.c +++ b/examples/typec/power_delivery/src/main.c @@ -63,9 +63,6 @@ int main(void) tuc_init(0, TUSB_TYPEC_PORT_SNK); - uint32_t start_ms = 0; - bool led_state = false; - while (1) { led_blinking_task(); @@ -155,6 +152,7 @@ bool tuc_pd_data_received_cb(uint8_t rhport, pd_header_t const* header, uint8_t } bool tuc_pd_control_received_cb(uint8_t rhport, pd_header_t const* header) { + (void) rhport; switch (header->msg_type) { case PD_CTRL_ACCEPT: printf("PD Request Accepted\r\n"); diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index 0132ef629..ec36df5c8 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -19,6 +19,33 @@ if (NOT EXISTS ${CMAKE_CURRENT_LIST_DIR}/${FAMILY}/family.cmake) message(FATAL_ERROR "Family '${FAMILY}' is not known/supported") endif() +set(WARNING_FLAGS_GNU + -Wall + -Wextra + -Werror + -Wfatal-errors + -Wdouble-promotion + -Wstrict-prototypes + -Wstrict-overflow + -Werror-implicit-function-declaration + -Wfloat-equal + -Wundef + -Wshadow + -Wwrite-strings + -Wsign-compare + -Wmissing-format-attribute + -Wunreachable-code + -Wcast-align + -Wcast-function-type + -Wcast-qual + -Wnull-dereference + -Wuninitialized + -Wunused + -Wreturn-type + -Wredundant-decls + ) + +set(WARNINGS_FLAGS_IAR "") function(family_filter RESULT DIR) get_filename_component(DIR ${DIR} ABSOLUTE BASE_DIR ${CMAKE_CURRENT_SOURCE_DIR}) @@ -121,6 +148,8 @@ function(family_configure_common TARGET) COMMAND ${CMAKE_SIZE} $ ) + target_compile_options(${TARGET} PUBLIC ${WARNING_FLAGS_${CMAKE_C_COMPILER_ID}}) + if (CMAKE_C_COMPILER_ID STREQUAL "GNU") # Generate map file target_link_options(${TARGET} PUBLIC diff --git a/hw/bsp/imxrt/family.c b/hw/bsp/imxrt/family.c index 46adabf0a..735fbdb9b 100644 --- a/hw/bsp/imxrt/family.c +++ b/hw/bsp/imxrt/family.c @@ -26,12 +26,23 @@ #include "bsp/board.h" #include "board.h" + +// Suppress warning caused by mcu driver +#ifdef __GNUC__ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wunused-parameter" +#endif + #include "fsl_device_registers.h" #include "fsl_gpio.h" #include "fsl_iomuxc.h" #include "fsl_clock.h" #include "fsl_lpuart.h" +#ifdef __GNUC__ +#pragma GCC diagnostic pop +#endif + #include "clock_config.h" #if defined(BOARD_TUD_RHPORT) && CFG_TUD_ENABLED diff --git a/hw/bsp/lpc55/family.cmake b/hw/bsp/lpc55/family.cmake index 43fbe8638..9f6b1f63d 100644 --- a/hw/bsp/lpc55/family.cmake +++ b/hw/bsp/lpc55/family.cmake @@ -102,6 +102,7 @@ function(family_configure_example TARGET) # external driver ${TOP}/lib/sct_neopixel/sct_neopixel.c ) + target_include_directories(${TARGET} PUBLIC # family, hw, board ${CMAKE_CURRENT_FUNCTION_LIST_DIR} diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 157b2bf21..6a559ada6 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -27,6 +27,15 @@ #include "bsp/board.h" #include "board.h" +// Suppress warning caused by mcu driver +#ifdef __GNUC__ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wcast-qual" +#pragma GCC diagnostic ignored "-Wcast-align" +#pragma GCC diagnostic ignored "-Wunused-parameter" +#pragma GCC diagnostic ignored "-Wundef" +#endif + #include "nrfx.h" #include "hal/nrf_gpio.h" #include "drivers/include/nrfx_power.h" @@ -37,6 +46,11 @@ #include "nrf_soc.h" #endif +#ifdef __GNUC__ +#pragma GCC diagnostic pop +#endif + + //--------------------------------------------------------------------+ // Forward USB interrupt events to TinyUSB IRQ Handler //--------------------------------------------------------------------+ diff --git a/hw/bsp/stm32g4/family.mk b/hw/bsp/stm32g4/family.mk index 5ed84422d..a4b644245 100644 --- a/hw/bsp/stm32g4/family.mk +++ b/hw/bsp/stm32g4/family.mk @@ -36,6 +36,7 @@ IAR_ASFLAGS += --cpu cortex-m4 --fpu VFPv4 SRC_C += \ src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c \ + src/portable/st/typec/typec_stm32.c \ $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \ $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \ diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index 231da5450..bf8b660f0 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -183,9 +183,9 @@ bool tcd_init(uint8_t rhport, uint32_t port_type) { // Read Voltage State on CC1 & CC2 fore initial state uint32_t v_cc[2]; + (void) v_cc; v_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; v_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; - TU_LOG1("Initial VState CC1 = %lu, CC2 = %lu\r\n", v_cc[0], v_cc[1]); // Enable CC1 & CC2 Interrupt @@ -308,8 +308,11 @@ void tcd_int_handler(uint8_t rhport) { if (!(sr & UCPD_SR_RXERR)) { // response with good crc - _good_crc.msg_id = ((pd_header_t const*) _rx_buf)->msg_id; - dma_tx_start(rhport, &_good_crc, 2); + // TODO move this to usbc stack + if (_rx_buf) { + _good_crc.msg_id = ((pd_header_t const *) _rx_buf)->msg_id; + dma_tx_start(rhport, &_good_crc, 2); + } result = XFER_RESULT_SUCCESS; }else { diff --git a/tools/cmake/toolchain/arm_gcc.cmake b/tools/cmake/toolchain/arm_gcc.cmake index 6dd1e7002..cefa9d2ce 100644 --- a/tools/cmake/toolchain/arm_gcc.cmake +++ b/tools/cmake/toolchain/arm_gcc.cmake @@ -35,32 +35,6 @@ set(TOOLCHAIN_EXE_LINKER_FLAGS -Wl,--cref ) -set(TOOLCHAIN_WARNING_FLAGS - -Wall - -Wextra - -Werror - -Wfatal-errors - -Wdouble-promotion - -Wstrict-prototypes - -Wstrict-overflow - -Werror-implicit-function-declaration - -Wfloat-equal - -Wundef - -Wshadow - -Wwrite-strings - -Wsign-compare - -Wmissing-format-attribute - -Wunreachable-code - -Wcast-align - -Wcast-function-type - -Wcast-qual - -Wnull-dereference - -Wuninitialized - -Wunused - -Wreturn-type - -Wredundant-decls - ) - include(${CMAKE_CURRENT_LIST_DIR}/set_flags.cmake) # try_compile is cmake test compiling its own example, diff --git a/tools/cmake/toolchain/arm_iar.cmake b/tools/cmake/toolchain/arm_iar.cmake index dfbe55e0d..a487e5b9f 100644 --- a/tools/cmake/toolchain/arm_iar.cmake +++ b/tools/cmake/toolchain/arm_iar.cmake @@ -28,7 +28,4 @@ list(APPEND TOOLCHAIN_COMMON_FLAGS list(APPEND TOOLCHAIN_EXE_LINKER_FLAGS ) -list(APPEND TOOLCHAIN_WARNING_FLAGS - ) - include(${CMAKE_CURRENT_LIST_DIR}/set_flags.cmake) -- cgit v1.3.1 From 3cfb838ba7f1f1a12203d36c9cbb615178af2cf7 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 26 Jun 2023 17:03:45 +0700 Subject: fix warnings when enable rtt with rp2040 --- hw/bsp/rp2040/family.c | 4 ++-- hw/bsp/rp2040/family.cmake | 6 +++++- src/portable/raspberrypi/rp2040/dcd_rp2040.c | 2 +- src/portable/raspberrypi/rp2040/rp2040_usb.c | 2 +- 4 files changed, 9 insertions(+), 5 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/rp2040/family.c b/hw/bsp/rp2040/family.c index 3aa989c0e..097e6fbd6 100644 --- a/hw/bsp/rp2040/family.c +++ b/hw/bsp/rp2040/family.c @@ -93,12 +93,12 @@ bool __no_inline_not_in_flash_func(get_bootsel_button)(void) { static void stdio_rtt_write (const char *buf, int length) { - SEGGER_RTT_Write(0, buf, length); + SEGGER_RTT_Write(0, buf, (unsigned) length); } static int stdio_rtt_read (char *buf, int len) { - return SEGGER_RTT_Read(0, buf, len); + return (int) SEGGER_RTT_Read(0, buf, (unsigned) len); } static stdio_driver_t stdio_rtt = diff --git a/hw/bsp/rp2040/family.cmake b/hw/bsp/rp2040/family.cmake index 28637e3ee..5cf6b1219 100644 --- a/hw/bsp/rp2040/family.cmake +++ b/hw/bsp/rp2040/family.cmake @@ -127,7 +127,7 @@ if (NOT TARGET _rp2040_family_inclusion_marker) target_compile_definitions(tinyusb_additions INTERFACE CFG_TUSB_DEBUG=${LOG}) endif() - if(LOGGER STREQUAL "rtt") + if(LOGGER STREQUAL "RTT" OR LOGGER STREQUAL "rtt") target_compile_definitions(tinyusb_additions INTERFACE LOGGER_RTT SEGGER_RTT_MODE_DEFAULT=SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL @@ -137,6 +137,10 @@ if (NOT TARGET _rp2040_family_inclusion_marker) ${TOP}/lib/SEGGER_RTT/RTT/SEGGER_RTT.c ) + set_source_files_properties(${TOP}/lib/SEGGER_RTT/RTT/SEGGER_RTT.c + PROPERTIES + COMPILE_FLAGS "-Wno-cast-qual -Wno-cast-align -Wno-sign-conversion") + target_include_directories(tinyusb_additions INTERFACE ${TOP}/lib/SEGGER_RTT/RTT ) diff --git a/src/portable/raspberrypi/rp2040/dcd_rp2040.c b/src/portable/raspberrypi/rp2040/dcd_rp2040.c index 500a5373f..479b17b67 100644 --- a/src/portable/raspberrypi/rp2040/dcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/dcd_rp2040.c @@ -189,7 +189,7 @@ static void hw_endpoint_xfer(uint8_t ep_addr, uint8_t *buffer, uint16_t total_by static void __tusb_irq_path_func(hw_handle_buff_status)(void) { uint32_t remaining_buffers = usb_hw->buf_status; - pico_trace("buf_status = 0x%08x\n", remaining_buffers); + pico_trace("buf_status = 0x%08lx\n", remaining_buffers); uint bit = 1u; for (uint8_t i = 0; remaining_buffers && i < USB_MAX_ENDPOINTS * 2; i++) { diff --git a/src/portable/raspberrypi/rp2040/rp2040_usb.c b/src/portable/raspberrypi/rp2040/rp2040_usb.c index cf37cba07..1f49665ff 100644 --- a/src/portable/raspberrypi/rp2040/rp2040_usb.c +++ b/src/portable/raspberrypi/rp2040/rp2040_usb.c @@ -419,7 +419,7 @@ static bool __tusb_irq_path_func(e15_is_critical_frame_period) (struct hw_endpoi if (delta < 800 || delta > 998) { return false; } - TU_LOG(3, "Avoiding sof %u now %lu last %lu\n", (usb_hw->sof_rd + 1) & USB_SOF_RD_BITS, time_us_32(), e15_last_sof); + TU_LOG(3, "Avoiding sof %lu now %lu last %lu\n", (usb_hw->sof_rd + 1) & USB_SOF_RD_BITS, time_us_32(), e15_last_sof); return true; } -- cgit v1.3.1 From 6284f2d72287396a0df153a0a7bd192c4e3847a7 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 29 Jun 2023 18:58:33 +0700 Subject: add hcd_frame_number() for pio-usb host --- .gitmodules | 0 hw/bsp/rp2040/board.h | 4 +++- src/portable/raspberrypi/pio_usb/hcd_pio_usb.c | 2 +- tools/get_deps.py | 2 +- 4 files changed, 5 insertions(+), 3 deletions(-) delete mode 100644 .gitmodules (limited to 'src/portable') diff --git a/.gitmodules b/.gitmodules deleted file mode 100644 index e69de29bb..000000000 diff --git a/hw/bsp/rp2040/board.h b/hw/bsp/rp2040/board.h index ccad00c4a..934e1c7ae 100644 --- a/hw/bsp/rp2040/board.h +++ b/hw/bsp/rp2040/board.h @@ -49,7 +49,10 @@ #define UART_RX_PIN PICO_DEFAULT_UART_RX_PIN #endif +//--------------------------------------------------------------------+ // PIO_USB +// default to pin on Adafruit Feather rp2040 USB Host or Tester if defined +//--------------------------------------------------------------------+ // #define USE_ADAFRUIT_RP2040_TESTER #ifdef USE_ADAFRUIT_RP2040_TESTER @@ -57,7 +60,6 @@ #define PICO_DEFAULT_PIO_USB_VBUSEN_PIN 22 #endif -// following default to pin on Adafruit Feather rp2040 USB Host #ifndef PICO_DEFAULT_PIO_USB_DP_PIN #define PICO_DEFAULT_PIO_USB_DP_PIN 16 #endif diff --git a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c index 58b153ac3..264af2e7a 100644 --- a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c +++ b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c @@ -105,7 +105,7 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) uint32_t hcd_frame_number(uint8_t rhport) { (void) rhport; - return 0; + return pio_usb_host_get_frame_number(); } void hcd_int_enable(uint8_t rhport) diff --git a/tools/get_deps.py b/tools/get_deps.py index 34e2f30a3..9b89c5e4c 100644 --- a/tools/get_deps.py +++ b/tools/get_deps.py @@ -54,7 +54,7 @@ deps_optional = { '950819b7de9b32f92c3edf396bc5ffb8d66e7009', 'kinetis_k32l2 kinetis_kl lpc51 lpc54 lpc55 mcx imxrt'], 'hw/mcu/raspberry_pi/Pico-PIO-USB': ['https://github.com/sekigon-gonnoc/Pico-PIO-USB.git', - 'c3715ce94b6f6391856de56081d4d9b3e98fa93d', + '58879cfa0eca5725d8db6443ec17f8896a321042', 'rp2040'], 'hw/mcu/renesas/fsp': ['https://github.com/renesas/fsp.git', '8dc14709f2a6518b43f71efad70d900b7718d9f1', -- cgit v1.3.1 From 99e75e6a8a0de9903e574a51d6ce8057a1e3e73f Mon Sep 17 00:00:00 2001 From: hathach Date: Sat, 1 Jul 2023 12:40:56 +0700 Subject: rework ra build --- .github/workflows/cmake_arm.yml | 1 + hw/bsp/ra/boards/ra4m1_ek/board.cmake | 15 ++ hw/bsp/ra/boards/ra4m1_ek/board.h | 53 +++++ hw/bsp/ra/boards/ra4m1_ek/board.mk | 7 - hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp_cfg.h | 6 +- .../boards/ra4m1_ek/fsp_cfg/bsp_mcu_family_cfg.h | 5 + hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.c | 232 -------------------- hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.ld | 1 + hw/bsp/ra/boards/ra4m3_ek/board.cmake | 15 ++ hw/bsp/ra/boards/ra4m3_ek/board.h | 52 +++++ hw/bsp/ra/boards/ra4m3_ek/board.mk | 7 - hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp_cfg.h | 4 +- hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.c | 236 --------------------- hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.ld | 1 + hw/bsp/ra/family.c | 231 ++++++++++++++++++++ hw/bsp/ra/family.cmake | 114 ++++++++++ hw/bsp/ra/family.mk | 2 +- src/portable/renesas/rusb2/rusb2_ra.h | 12 ++ 18 files changed, 509 insertions(+), 485 deletions(-) create mode 100644 hw/bsp/ra/boards/ra4m1_ek/board.cmake create mode 100644 hw/bsp/ra/boards/ra4m1_ek/board.h delete mode 100644 hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.c create mode 100644 hw/bsp/ra/boards/ra4m3_ek/board.cmake create mode 100644 hw/bsp/ra/boards/ra4m3_ek/board.h delete mode 100644 hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.c create mode 100644 hw/bsp/ra/family.c create mode 100644 hw/bsp/ra/family.cmake (limited to 'src/portable') diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index 0ce63281e..4d8cd5591 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -38,6 +38,7 @@ jobs: - 'lpc18' - 'lpc55' - 'mcx' + - 'ra' - 'rp2040' - 'stm32f0' - 'stm32f1' diff --git a/hw/bsp/ra/boards/ra4m1_ek/board.cmake b/hw/bsp/ra/boards/ra4m1_ek/board.cmake new file mode 100644 index 000000000..37c39061d --- /dev/null +++ b/hw/bsp/ra/boards/ra4m1_ek/board.cmake @@ -0,0 +1,15 @@ +set(CMAKE_SYSTEM_PROCESSOR cortex-m4 CACHE INTERNAL "System Processor") +set(MCU_VARIANT ra4m1) + +set(JLINK_DEVICE R7FA4M1AB) + +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/ra4m1_ek.ld) + +function(update_board TARGET) + target_compile_definitions(${TARGET} PUBLIC + ) + target_sources(${TARGET} PRIVATE + ) + target_include_directories(${BOARD_TARGET} PUBLIC + ) +endfunction() diff --git a/hw/bsp/ra/boards/ra4m1_ek/board.h b/hw/bsp/ra/boards/ra4m1_ek/board.h new file mode 100644 index 000000000..383ab7399 --- /dev/null +++ b/hw/bsp/ra/boards/ra4m1_ek/board.h @@ -0,0 +1,53 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +#define LED1 (BSP_IO_PORT_01_PIN_06) +#define LED_STATE_ON 1 + +#define SW1 (BSP_IO_PORT_01_PIN_05) +#define BUTTON_STATE_ACTIVE 0 + +const ioport_pin_cfg_t board_pin_cfg[] = { + { .pin = LED1, .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_OUTPUT | (uint32_t) IOPORT_CFG_PORT_OUTPUT_LOW) }, + { .pin = SW1 , .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_INPUT) }, + + { .pin = BSP_IO_PORT_04_PIN_07, .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS) }, + { .pin = BSP_IO_PORT_09_PIN_14, .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS) }, + { .pin = BSP_IO_PORT_09_PIN_15, .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS) }, +}; + +#ifdef __cplusplus +} +#endif + +#endif diff --git a/hw/bsp/ra/boards/ra4m1_ek/board.mk b/hw/bsp/ra/boards/ra4m1_ek/board.mk index eae68f87d..9b0fafb28 100644 --- a/hw/bsp/ra/boards/ra4m1_ek/board.mk +++ b/hw/bsp/ra/boards/ra4m1_ek/board.mk @@ -3,13 +3,6 @@ MCU_VARIANT = ra4m1 FSP_BOARD_DIR = hw/mcu/renesas/fsp/ra/board/ra4m1_ek -SRC_C += \ - $(FSP_BOARD_DIR)/board_init.c \ - $(FSP_BOARD_DIR)/board_leds.c \ - -INC += \ - $(TOP)/$(FSP_BOARD_DIR) - # All source paths should be relative to the top level. LD_FILE = $(BOARD_PATH)/ra4m1_ek.ld diff --git a/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp_cfg.h b/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp_cfg.h index b38a79b40..b337e49f2 100644 --- a/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp_cfg.h +++ b/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp_cfg.h @@ -2,7 +2,6 @@ #ifndef BSP_CFG_H_ #define BSP_CFG_H_ -#include "board.h" #include "bsp_clock_cfg.h" #include "bsp_mcu_family_cfg.h" @@ -32,4 +31,9 @@ #define BSP_CLOCK_CFG_SUBCLOCK_POPULATED (1) #define BSP_CLOCK_CFG_SUBCLOCK_STABILIZATION_MS 1000 +#define BSP_FEATURE_TFU_SUPPORTED 0 + +// for SystemInit() +void bsp_init(void * p_args); + #endif /* BSP_CFG_H_ */ diff --git a/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp_mcu_family_cfg.h b/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp_mcu_family_cfg.h index 3bde2db0d..4e080023e 100644 --- a/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp_mcu_family_cfg.h +++ b/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp_mcu_family_cfg.h @@ -25,6 +25,11 @@ #define BSP_CORTEX_VECTOR_TABLE_ENTRIES (16U) #define BSP_VECTOR_TABLE_MAX_ENTRIES (48U) +#define BSP_TZ_SECURE_BUILD (0) +#define BSP_TZ_NONSECURE_BUILD (0) + +#define BSP_FEATURE_BSP_HAS_SCISPI_CLOCK 0 + #define OFS_SEQ1 0xA001A001 | (1 << 1) | (3 << 2) #define OFS_SEQ2 (15 << 4) | (3 << 8) | (3 << 10) #define OFS_SEQ3 (1 << 12) | (1 << 14) | (1 << 17) diff --git a/hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.c b/hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.c deleted file mode 100644 index ea2204837..000000000 --- a/hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.c +++ /dev/null @@ -1,232 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2022, Rafael Silva - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include - -#include "bsp/board.h" -#include "bsp_api.h" -#include "r_ioport.h" -#include "r_ioport_api.h" -#include "renesas.h" - -/* Key code for writing PRCR register. */ -#define BSP_PRV_PRCR_KEY (0xA500U) -#define BSP_PRV_PRCR_PRC1_UNLOCK ((BSP_PRV_PRCR_KEY) | 0x2U) -#define BSP_PRV_PRCR_LOCK ((BSP_PRV_PRCR_KEY) | 0x0U) - -#define SW1 (BSP_IO_PORT_01_PIN_05) -#define LED1 (BSP_IO_PORT_01_PIN_06) - -#define LED_STATE_ON 1 -#define BUTTON_STATE_ACTIVE 0 - -/* ISR prototypes */ -void usbfs_interrupt_handler(void); -void usbfs_resume_handler(void); -void usbfs_d0fifo_handler(void); -void usbfs_d1fifo_handler(void); - -BSP_DONT_REMOVE const - fsp_vector_t g_vector_table[BSP_ICU_VECTOR_MAX_ENTRIES] BSP_PLACE_IN_SECTION(BSP_SECTION_APPLICATION_VECTORS) = { - [0] = usbfs_interrupt_handler, /* USBFS INT (USBFS interrupt) */ - [1] = usbfs_resume_handler, /* USBFS RESUME (USBFS resume interrupt) */ - [2] = usbfs_d0fifo_handler, /* USBFS FIFO 0 (DMA transfer request 0) */ - [3] = usbfs_d1fifo_handler, /* USBFS FIFO 1 (DMA transfer request 1) */ -}; -const bsp_interrupt_event_t g_interrupt_event_link_select[BSP_ICU_VECTOR_MAX_ENTRIES] = { - [0] = BSP_PRV_IELS_ENUM(EVENT_USBFS_INT), /* USBFS INT (USBFS interrupt) */ - [1] = BSP_PRV_IELS_ENUM(EVENT_USBFS_RESUME), /* USBFS RESUME (USBFS resume interrupt) */ - [2] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_0), /* USBFS FIFO 0 (DMA transfer request 0) */ - [3] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_1) /* USBFS FIFO 1 (DMA transfer request 1) */ -}; - -const ioport_pin_cfg_t g_bsp_pin_cfg_data[] = { - { .pin = LED1, .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_OUTPUT | (uint32_t) IOPORT_CFG_PORT_OUTPUT_LOW) }, - { .pin = SW1 , .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_INPUT) }, - - { .pin = BSP_IO_PORT_04_PIN_07, .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS) }, - { .pin = BSP_IO_PORT_09_PIN_14, .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS) }, - { .pin = BSP_IO_PORT_09_PIN_15, .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS) }, - -}; - -const ioport_cfg_t g_bsp_pin_cfg = { - .number_of_pins = sizeof(g_bsp_pin_cfg_data) / sizeof(ioport_pin_cfg_t), - .p_pin_cfg_data = &g_bsp_pin_cfg_data[0], -}; -ioport_instance_ctrl_t g_ioport_ctrl; -const ioport_instance_t g_ioport = {.p_api = &g_ioport_on_ioport, .p_ctrl = &g_ioport_ctrl, .p_cfg = &g_bsp_pin_cfg}; - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void usbfs_interrupt_handler(void) -{ - IRQn_Type irq = R_FSP_CurrentIrqGet(); - R_BSP_IrqStatusClear(irq); - -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif - -#if CFG_TUD_ENABLED - tud_int_handler(0); -#endif -} - -void usbfs_resume_handler(void) -{ - IRQn_Type irq = R_FSP_CurrentIrqGet(); - R_BSP_IrqStatusClear(irq); - -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif - -#if CFG_TUD_ENABLED - tud_int_handler(0); -#endif -} - -void usbfs_d0fifo_handler(void) -{ - IRQn_Type irq = R_FSP_CurrentIrqGet(); - R_BSP_IrqStatusClear(irq); - -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif - -#if CFG_TUD_ENABLED - tud_int_handler(0); -#endif -} - -void usbfs_d1fifo_handler(void) -{ - IRQn_Type irq = R_FSP_CurrentIrqGet(); - R_BSP_IrqStatusClear(irq); - -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif - -#if CFG_TUD_ENABLED - tud_int_handler(0); -#endif -} - -void board_init(void) -{ - /* Configure pins. */ - R_IOPORT_Open(&g_ioport_ctrl, &g_bsp_pin_cfg); - - /* Enable USB_BASE */ - R_SYSTEM->PRCR = (uint16_t) BSP_PRV_PRCR_PRC1_UNLOCK; - R_MSTP->MSTPCRB &= ~(1U << 11U); - R_SYSTEM->PRCR = (uint16_t) BSP_PRV_PRCR_LOCK; - -#if CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(TU_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); - NVIC_SetPriority(USBFS_RESUME_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); - NVIC_SetPriority(USBFS_FIFO_0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); - NVIC_SetPriority(USBFS_FIFO_1_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); -#endif - -#if CFG_TUSB_OS == OPT_OS_NONE - /* Init systick */ - SysTick_Config(SystemCoreClock / 1000); -#endif -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - R_IOPORT_PinWrite(&g_ioport_ctrl, LED1, state ? LED_STATE_ON : !LED_STATE_ON); -} - -uint32_t board_button_read(void) -{ - bsp_io_level_t lvl; - R_IOPORT_PinRead(&g_ioport_ctrl, SW1, &lvl); - return lvl == BUTTON_STATE_ACTIVE; -} - -int board_uart_read(uint8_t *buf, int len) -{ - (void) buf; - (void) len; - return 0; -} - -int board_uart_write(void const *buf, int len) -{ - (void) buf; - (void) len; - return 0; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#else -#endif - -int close(int fd) -{ - (void) fd; - return -1; -} -int fstat(int fd, void *pstat) -{ - (void) fd; - (void) pstat; - return 0; -} -off_t lseek(int fd, off_t pos, int whence) -{ - (void) fd; - (void) pos; - (void) whence; - return 0; -} -int isatty(int fd) -{ - (void) fd; - return 1; -} diff --git a/hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.ld b/hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.ld index 8ddaa0a97..63c1d33aa 100644 --- a/hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.ld +++ b/hw/bsp/ra/boards/ra4m1_ek/ra4m1_ek.ld @@ -553,6 +553,7 @@ SECTIONS { . = ALIGN(8); __HeapBase = .; + PROVIDE(end = .); /* Place the STD heap here. */ KEEP(*(.heap)) __HeapLimit = .; diff --git a/hw/bsp/ra/boards/ra4m3_ek/board.cmake b/hw/bsp/ra/boards/ra4m3_ek/board.cmake new file mode 100644 index 000000000..241b659a0 --- /dev/null +++ b/hw/bsp/ra/boards/ra4m3_ek/board.cmake @@ -0,0 +1,15 @@ +set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor") +set(MCU_VARIANT ra4m3) + +set(JLINK_DEVICE R7FA4M3AF) + +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/ra4m3_ek.ld) + +function(update_board TARGET) + target_compile_definitions(${TARGET} PUBLIC + ) + target_sources(${TARGET} PRIVATE + ) + target_include_directories(${BOARD_TARGET} PUBLIC + ) +endfunction() diff --git a/hw/bsp/ra/boards/ra4m3_ek/board.h b/hw/bsp/ra/boards/ra4m3_ek/board.h new file mode 100644 index 000000000..e41302f90 --- /dev/null +++ b/hw/bsp/ra/boards/ra4m3_ek/board.h @@ -0,0 +1,52 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +#define LED1 (BSP_IO_PORT_04_PIN_15) +#define LED_STATE_ON 1 + +#define SW1 (BSP_IO_PORT_00_PIN_05) +#define BUTTON_STATE_ACTIVE 0 + +const ioport_pin_cfg_t board_pin_cfg[] = { + {.pin = BSP_IO_PORT_04_PIN_07, .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS)}, + {.pin = BSP_IO_PORT_05_PIN_00, .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS)}, + {.pin = BSP_IO_PORT_05_PIN_01, .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS)}, + {.pin = LED1, .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_OUTPUT | (uint32_t) IOPORT_CFG_PORT_OUTPUT_LOW)}, + {.pin = SW1, .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_INPUT)}, +}; + +#ifdef __cplusplus +} +#endif + +#endif diff --git a/hw/bsp/ra/boards/ra4m3_ek/board.mk b/hw/bsp/ra/boards/ra4m3_ek/board.mk index 4ca1d365e..266de7c0d 100644 --- a/hw/bsp/ra/boards/ra4m3_ek/board.mk +++ b/hw/bsp/ra/boards/ra4m3_ek/board.mk @@ -3,13 +3,6 @@ MCU_VARIANT = ra4m3 FSP_BOARD_DIR = hw/mcu/renesas/fsp/ra/board/ra4m3_ek -SRC_C += \ - $(FSP_BOARD_DIR)/board_init.c \ - $(FSP_BOARD_DIR)/board_leds.c \ - -INC += \ - $(TOP)/$(FSP_BOARD_DIR) - # All source paths should be relative to the top level. LD_FILE = $(BOARD_PATH)/ra4m3_ek.ld diff --git a/hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp_cfg.h b/hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp_cfg.h index a84d81e8d..a9cb8210b 100755 --- a/hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp_cfg.h +++ b/hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp_cfg.h @@ -2,7 +2,6 @@ #ifndef BSP_CFG_H_ #define BSP_CFG_H_ -#include "board.h" #include "bsp_clock_cfg.h" #include "bsp_mcu_family_cfg.h" @@ -32,4 +31,7 @@ #define BSP_CLOCK_CFG_SUBCLOCK_POPULATED (1) #define BSP_CLOCK_CFG_SUBCLOCK_STABILIZATION_MS 1000 +// for SystemInit() +void bsp_init(void * p_args); + #endif /* BSP_CFG_H_ */ diff --git a/hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.c b/hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.c deleted file mode 100644 index 327ef71d5..000000000 --- a/hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.c +++ /dev/null @@ -1,236 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2022, Rafael Silva - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include - -#include "bsp/board.h" -#include "bsp_api.h" -#include "r_ioport.h" -#include "r_ioport_api.h" -#include "renesas.h" - -/* Key code for writing PRCR register. */ -#define BSP_PRV_PRCR_KEY (0xA500U) -#define BSP_PRV_PRCR_PRC1_UNLOCK ((BSP_PRV_PRCR_KEY) | 0x2U) -#define BSP_PRV_PRCR_LOCK ((BSP_PRV_PRCR_KEY) | 0x0U) - -#define SW1 (BSP_IO_PORT_00_PIN_05) -#define SW2 (BSP_IO_PORT_00_PIN_06) -#define LED1 (BSP_IO_PORT_04_PIN_15) -#define LED3 (BSP_IO_PORT_04_PIN_00) -#define LED2 (BSP_IO_PORT_04_PIN_04) - -/* ISR prototypes */ -void usbfs_interrupt_handler(void); -void usbfs_resume_handler(void); -void usbfs_d0fifo_handler(void); -void usbfs_d1fifo_handler(void); - -BSP_DONT_REMOVE const - fsp_vector_t g_vector_table[BSP_ICU_VECTOR_MAX_ENTRIES] BSP_PLACE_IN_SECTION(BSP_SECTION_APPLICATION_VECTORS) = { - [0] = usbfs_interrupt_handler, /* USBFS INT (USBFS interrupt) */ - [1] = usbfs_resume_handler, /* USBFS RESUME (USBFS resume interrupt) */ - [2] = usbfs_d0fifo_handler, /* USBFS FIFO 0 (DMA transfer request 0) */ - [3] = usbfs_d1fifo_handler, /* USBFS FIFO 1 (DMA transfer request 1) */ -}; -const bsp_interrupt_event_t g_interrupt_event_link_select[BSP_ICU_VECTOR_MAX_ENTRIES] = { - [0] = BSP_PRV_IELS_ENUM(EVENT_USBFS_INT), /* USBFS INT (USBFS interrupt) */ - [1] = BSP_PRV_IELS_ENUM(EVENT_USBFS_RESUME), /* USBFS RESUME (USBFS resume interrupt) */ - [2] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_0), /* USBFS FIFO 0 (DMA transfer request 0) */ - [3] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_1) /* USBFS FIFO 1 (DMA transfer request 1) */ -}; - -const ioport_pin_cfg_t g_bsp_pin_cfg_data[] = { - {.pin = BSP_IO_PORT_04_PIN_07, - .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS)}, - {.pin = BSP_IO_PORT_05_PIN_00, - .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS)}, - {.pin = BSP_IO_PORT_05_PIN_01, - .pin_cfg = ((uint32_t) IOPORT_CFG_PERIPHERAL_PIN | (uint32_t) IOPORT_PERIPHERAL_USB_FS)}, - {.pin = LED1, .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_OUTPUT | (uint32_t) IOPORT_CFG_PORT_OUTPUT_LOW)}, - {.pin = LED2, .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_OUTPUT | (uint32_t) IOPORT_CFG_PORT_OUTPUT_LOW)}, - {.pin = LED3, .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_OUTPUT | (uint32_t) IOPORT_CFG_PORT_OUTPUT_LOW)}, - {.pin = SW1, .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_INPUT)}, - {.pin = SW2, .pin_cfg = ((uint32_t) IOPORT_CFG_PORT_DIRECTION_INPUT)}}; - -const ioport_cfg_t g_bsp_pin_cfg = { - .number_of_pins = sizeof(g_bsp_pin_cfg_data) / sizeof(ioport_pin_cfg_t), - .p_pin_cfg_data = &g_bsp_pin_cfg_data[0], -}; -ioport_instance_ctrl_t g_ioport_ctrl; -const ioport_instance_t g_ioport = {.p_api = &g_ioport_on_ioport, .p_ctrl = &g_ioport_ctrl, .p_cfg = &g_bsp_pin_cfg}; - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void usbfs_interrupt_handler(void) -{ - IRQn_Type irq = R_FSP_CurrentIrqGet(); - R_BSP_IrqStatusClear(irq); - -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif - -#if CFG_TUD_ENABLED - tud_int_handler(0); -#endif -} -void usbfs_resume_handler(void) -{ - IRQn_Type irq = R_FSP_CurrentIrqGet(); - R_BSP_IrqStatusClear(irq); - -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif - -#if CFG_TUD_ENABLED - tud_int_handler(0); -#endif -} - -void usbfs_d0fifo_handler(void) -{ - IRQn_Type irq = R_FSP_CurrentIrqGet(); - R_BSP_IrqStatusClear(irq); - -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif - -#if CFG_TUD_ENABLED - tud_int_handler(0); -#endif -} - -void usbfs_d1fifo_handler(void) -{ - IRQn_Type irq = R_FSP_CurrentIrqGet(); - R_BSP_IrqStatusClear(irq); - -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif - -#if CFG_TUD_ENABLED - tud_int_handler(0); -#endif -} - -void board_init(void) -{ - /* Configure pins. */ - R_IOPORT_Open(&g_ioport_ctrl, &g_bsp_pin_cfg); - - /* Enable USB_BASE */ - R_SYSTEM->PRCR = (uint16_t) BSP_PRV_PRCR_PRC1_UNLOCK; - R_MSTP->MSTPCRB &= ~(1U << 11U); - R_SYSTEM->PRCR = (uint16_t) BSP_PRV_PRCR_LOCK; - -#if CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(TU_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); - NVIC_SetPriority(USBFS_RESUME_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); - NVIC_SetPriority(USBFS_FIFO_0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); - NVIC_SetPriority(USBFS_FIFO_1_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); -#endif - -#if CFG_TUSB_OS == OPT_OS_NONE - /* Init systick */ - SysTick_Config(SystemCoreClock / 1000); -#endif -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - R_IOPORT_PinWrite(&g_ioport_ctrl, LED1, state); - R_IOPORT_PinWrite(&g_ioport_ctrl, LED2, state); - R_IOPORT_PinWrite(&g_ioport_ctrl, LED3, state); -} - -uint32_t board_button_read(void) -{ - bsp_io_level_t lvl; - R_IOPORT_PinRead(&g_ioport_ctrl, SW1, &lvl); - return lvl; -} - -int board_uart_read(uint8_t *buf, int len) -{ - (void) buf; - (void) len; - return 0; -} - -int board_uart_write(void const *buf, int len) -{ - (void) buf; - (void) len; - return 0; -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#else -#endif - -int close(int fd) -{ - (void) fd; - return -1; -} -int fstat(int fd, void *pstat) -{ - (void) fd; - (void) pstat; - return 0; -} -off_t lseek(int fd, off_t pos, int whence) -{ - (void) fd; - (void) pos; - (void) whence; - return 0; -} -int isatty(int fd) -{ - (void) fd; - return 1; -} diff --git a/hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.ld b/hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.ld index 5bc335cb4..520b44cc6 100644 --- a/hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.ld +++ b/hw/bsp/ra/boards/ra4m3_ek/ra4m3_ek.ld @@ -413,6 +413,7 @@ SECTIONS { . = ALIGN(8); __HeapBase = .; + PROVIDE(end = .); /* Place the STD heap here. */ KEEP(*(.heap)) __HeapLimit = .; diff --git a/hw/bsp/ra/family.c b/hw/bsp/ra/family.c new file mode 100644 index 000000000..42cb2d4a4 --- /dev/null +++ b/hw/bsp/ra/family.c @@ -0,0 +1,231 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2022, Rafael Silva + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include + +#ifdef __GNUC__ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wstrict-prototypes" +#pragma GCC diagnostic ignored "-Wundef" + +// extra push due to https://github.com/renesas/fsp/pull/278 +#pragma GCC diagnostic push +#endif + +#include "bsp_api.h" + +#ifdef __GNUC__ +#pragma GCC diagnostic pop +#endif + +#include "r_ioport.h" +#include "r_ioport_api.h" +#include "renesas.h" + +#include "bsp/board.h" +#include "board.h" + +/* Key code for writing PRCR register. */ +#define BSP_PRV_PRCR_KEY (0xA500U) +#define BSP_PRV_PRCR_PRC1_UNLOCK ((BSP_PRV_PRCR_KEY) | 0x2U) +#define BSP_PRV_PRCR_LOCK ((BSP_PRV_PRCR_KEY) | 0x0U) + +/* ISR prototypes */ +void usbfs_interrupt_handler(void); +void usbfs_resume_handler(void); +void usbfs_d0fifo_handler(void); +void usbfs_d1fifo_handler(void); + +BSP_DONT_REMOVE const +fsp_vector_t g_vector_table[BSP_ICU_VECTOR_MAX_ENTRIES] BSP_PLACE_IN_SECTION(BSP_SECTION_APPLICATION_VECTORS) = { + [0] = usbfs_interrupt_handler, /* USBFS INT (USBFS interrupt) */ + [1] = usbfs_resume_handler, /* USBFS RESUME (USBFS resume interrupt) */ + [2] = usbfs_d0fifo_handler, /* USBFS FIFO 0 (DMA transfer request 0) */ + [3] = usbfs_d1fifo_handler, /* USBFS FIFO 1 (DMA transfer request 1) */ +}; +const bsp_interrupt_event_t g_interrupt_event_link_select[BSP_ICU_VECTOR_MAX_ENTRIES] = { + [0] = BSP_PRV_IELS_ENUM(EVENT_USBFS_INT), /* USBFS INT (USBFS interrupt) */ + [1] = BSP_PRV_IELS_ENUM(EVENT_USBFS_RESUME), /* USBFS RESUME (USBFS resume interrupt) */ + [2] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_0), /* USBFS FIFO 0 (DMA transfer request 0) */ + [3] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_1) /* USBFS FIFO 1 (DMA transfer request 1) */ +}; + +const ioport_cfg_t g_bsp_pin_cfg = { + .number_of_pins = sizeof(board_pin_cfg) / sizeof(ioport_pin_cfg_t), + .p_pin_cfg_data = board_pin_cfg, +}; +ioport_instance_ctrl_t g_ioport_ctrl; +//const ioport_instance_t g_ioport = {.p_api = &g_ioport_on_ioport, .p_ctrl = &g_ioport_ctrl, .p_cfg = &g_bsp_pin_cfg}; + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void usbfs_interrupt_handler(void) +{ + IRQn_Type irq = R_FSP_CurrentIrqGet(); + R_BSP_IrqStatusClear(irq); + +#if CFG_TUH_ENABLED + tuh_int_handler(0); +#endif + +#if CFG_TUD_ENABLED + tud_int_handler(0); +#endif +} + +void usbfs_resume_handler(void) +{ + IRQn_Type irq = R_FSP_CurrentIrqGet(); + R_BSP_IrqStatusClear(irq); + +#if CFG_TUH_ENABLED + tuh_int_handler(0); +#endif + +#if CFG_TUD_ENABLED + tud_int_handler(0); +#endif +} + +void usbfs_d0fifo_handler(void) +{ + IRQn_Type irq = R_FSP_CurrentIrqGet(); + R_BSP_IrqStatusClear(irq); + +#if CFG_TUH_ENABLED + tuh_int_handler(0); +#endif + +#if CFG_TUD_ENABLED + tud_int_handler(0); +#endif +} + +void usbfs_d1fifo_handler(void) +{ + IRQn_Type irq = R_FSP_CurrentIrqGet(); + R_BSP_IrqStatusClear(irq); + +#if CFG_TUH_ENABLED + tuh_int_handler(0); +#endif + +#if CFG_TUD_ENABLED + tud_int_handler(0); +#endif +} + +void board_init(void) +{ + /* Configure pins. */ + R_IOPORT_Open(&g_ioport_ctrl, &g_bsp_pin_cfg); + + /* Enable USB_BASE */ + R_SYSTEM->PRCR = (uint16_t) BSP_PRV_PRCR_PRC1_UNLOCK; + R_MSTP->MSTPCRB &= ~(1U << 11U); + R_SYSTEM->PRCR = (uint16_t) BSP_PRV_PRCR_LOCK; + +#if CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(TU_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + NVIC_SetPriority(USBFS_RESUME_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + NVIC_SetPriority(USBFS_FIFO_0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + NVIC_SetPriority(USBFS_FIFO_1_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); +#endif + +#if CFG_TUSB_OS == OPT_OS_NONE + /* Init systick */ + SysTick_Config(SystemCoreClock / 1000); +#endif +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + R_IOPORT_PinWrite(&g_ioport_ctrl, LED1, state ? LED_STATE_ON : !LED_STATE_ON); +} + +uint32_t board_button_read(void) +{ + bsp_io_level_t lvl; + R_IOPORT_PinRead(&g_ioport_ctrl, SW1, &lvl); + return lvl == BUTTON_STATE_ACTIVE; +} + +int board_uart_read(uint8_t *buf, int len) +{ + (void) buf; + (void) len; + return 0; +} + +int board_uart_write(void const *buf, int len) +{ + (void) buf; + (void) len; + return 0; +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif + +int close(int fd) +{ + (void) fd; + return -1; +} +int fstat(int fd, void *pstat) +{ + (void) fd; + (void) pstat; + return 0; +} +off_t lseek(int fd, off_t pos, int whence) +{ + (void) fd; + (void) pos; + (void) whence; + return 0; +} +int isatty(int fd) +{ + (void) fd; + return 1; +} diff --git a/hw/bsp/ra/family.cmake b/hw/bsp/ra/family.cmake new file mode 100644 index 000000000..c4c25bf4f --- /dev/null +++ b/hw/bsp/ra/family.cmake @@ -0,0 +1,114 @@ +include_guard() + +if (NOT BOARD) + message(FATAL_ERROR "BOARD not specified") +endif () + +set(CMSIS_DIR ${TOP}/lib/CMSIS_5) +set(FSP_RA ${TOP}/hw/mcu/renesas/fsp/ra/fsp) + +# include board specific +include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) + +set(CMAKE_TOOLCHAIN_FILE ${TOP}/tools/cmake/toolchain/arm_${TOOLCHAIN}.cmake) + +set(FAMILY_MCUS RA CACHE INTERNAL "") + +#------------------------------------ +# BOARD_TARGET +#------------------------------------ +# only need to be built ONCE for all examples +function(add_board_target BOARD_TARGET) + if (NOT TARGET ${BOARD_TARGET}) + add_library(${BOARD_TARGET} STATIC + ${FSP_RA}/src/bsp/cmsis/Device/RENESAS/Source/startup.c + ${FSP_RA}/src/bsp/cmsis/Device/RENESAS/Source/system.c + ${FSP_RA}/src/bsp/mcu/all/bsp_clocks.c + ${FSP_RA}/src/bsp/mcu/all/bsp_common.c + ${FSP_RA}/src/bsp/mcu/all/bsp_delay.c + ${FSP_RA}/src/bsp/mcu/all/bsp_group_irq.c + ${FSP_RA}/src/bsp/mcu/all/bsp_guard.c + ${FSP_RA}/src/bsp/mcu/all/bsp_io.c + ${FSP_RA}/src/bsp/mcu/all/bsp_irq.c + ${FSP_RA}/src/bsp/mcu/all/bsp_register_protection.c + ${FSP_RA}/src/bsp/mcu/all/bsp_rom_registers.c + ${FSP_RA}/src/bsp/mcu/all/bsp_sbrk.c + ${FSP_RA}/src/bsp/mcu/all/bsp_security.c + ${FSP_RA}/src/r_ioport/r_ioport.c + ) + target_compile_definitions(${BOARD_TARGET} PUBLIC + _RA_TZ_NONSECURE + ) + + target_compile_options(${BOARD_TARGET} PUBLIC + -ffreestanding + ) + + target_include_directories(${BOARD_TARGET} PUBLIC + ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD}/fsp_cfg + ${CMSIS_DIR}/CMSIS/Core/Include + ${FSP_RA}/inc + ${FSP_RA}/inc/api + ${FSP_RA}/inc/instances + ${FSP_RA}/src/bsp/cmsis/Device/RENESAS/Include + ${FSP_RA}/src/bsp/mcu/${MCU_VARIANT} + ) + + update_board(${BOARD_TARGET}) + + if (CMAKE_C_COMPILER_ID STREQUAL "GNU") + target_link_options(${BOARD_TARGET} PUBLIC + # linker file + "LINKER:--script=${LD_FILE_GNU}" + -nostartfiles + # nanolib + --specs=nano.specs + --specs=nosys.specs + ) + elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--config=${LD_FILE_IAR}" + ) + endif () + endif () +endfunction() + + +#------------------------------------ +# Functions +#------------------------------------ +function(family_configure_example TARGET RTOS) + family_configure_common(${TARGET} ${RTOS}) + + # Board target + add_board_target(board_${BOARD}) + + #---------- Port Specific ---------- + # These files are built for each example since it depends on example's tusb_config.h + target_sources(${TARGET} PUBLIC + # BSP + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c + ) + target_include_directories(${TARGET} PUBLIC + # family, hw, board + ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../ + ) + + # Add TinyUSB target and port source + family_add_tinyusb(${TARGET} OPT_MCU_RAXXX ${RTOS}) + target_sources(${TARGET}-tinyusb PUBLIC + ${TOP}/src/portable/renesas/rusb2/dcd_rusb2.c + ${TOP}/src/portable/renesas/rusb2/hcd_rusb2.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) + + # Link dependencies + target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) + + # Flashing + family_flash_jlink(${TARGET}) +endfunction() diff --git a/hw/bsp/ra/family.mk b/hw/bsp/ra/family.mk index 103d3cfa6..8e4f80eaf 100644 --- a/hw/bsp/ra/family.mk +++ b/hw/bsp/ra/family.mk @@ -35,9 +35,9 @@ SRC_C += \ INC += \ $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ - $(TOP)/$(FSP_RA)/src/bsp/cmsis/Device/RENESAS/Include \ $(TOP)/$(BOARD_PATH) \ $(TOP)/$(BOARD_PATH)/fsp_cfg \ + $(TOP)/$(FSP_RA)/src/bsp/cmsis/Device/RENESAS/Include \ $(TOP)/$(FSP_RA)/inc \ $(TOP)/$(FSP_RA)/inc/api \ $(TOP)/$(FSP_RA)/inc/instances \ diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 5be9f11ce..be0a9fa66 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -31,9 +31,21 @@ extern "C" { #endif +#ifdef __GNUC__ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wstrict-prototypes" + +// extra push due to https://github.com/renesas/fsp/pull/278 +#pragma GCC diagnostic push +#endif + /* renesas fsp api */ #include "bsp_api.h" +#ifdef __GNUC__ +#pragma GCC diagnostic pop +#endif + #define RUSB2_REG_BASE (0x40090000) #if defined(__ICCARM__) -- cgit v1.3.1 From e7431f54f207b8563f2d8dba3384dba243d55bf4 Mon Sep 17 00:00:00 2001 From: hathach Date: Sat, 1 Jul 2023 17:46:21 +0700 Subject: fix undef with fsp --- src/portable/renesas/rusb2/rusb2_ra.h | 1 + 1 file changed, 1 insertion(+) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index be0a9fa66..df4afdfa0 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -34,6 +34,7 @@ extern "C" { #ifdef __GNUC__ #pragma GCC diagnostic push #pragma GCC diagnostic ignored "-Wstrict-prototypes" +#pragma GCC diagnostic ignored "-Wundef" // extra push due to https://github.com/renesas/fsp/pull/278 #pragma GCC diagnostic push -- cgit v1.3.1 From 0693462ebad20338de78aeb93d60d6c3c73a6ca7 Mon Sep 17 00:00:00 2001 From: Lars Pötter Date: Sun, 2 Jul 2023 09:02:24 +0200 Subject: made line ends consistent. --- src/class/cdc/cdc_host.c | 4 ++-- src/class/video/video_device.c | 16 +++++++------- src/common/tusb_fifo.c | 2 +- src/portable/dialog/da146xx/dcd_da146xx.c | 2 +- src/portable/mentor/musb/dcd_musb.c | 30 +++++++++++++------------- src/portable/mentor/musb/hcd_musb.c | 8 +++---- src/portable/nxp/khci/hcd_khci.c | 16 +++++++------- src/portable/raspberrypi/rp2040/hcd_rp2040.c | 4 ++-- src/portable/raspberrypi/rp2040/rp2040_usb.c | 4 ++-- src/portable/renesas/rusb2/hcd_rusb2.c | 8 +++---- src/portable/st/typec/typec_stm32.c | 18 ++++++++-------- src/portable/sunxi/dcd_sunxi_musb.c | 32 ++++++++++++++-------------- 12 files changed, 72 insertions(+), 72 deletions(-) (limited to 'src/portable') diff --git a/src/class/cdc/cdc_host.c b/src/class/cdc/cdc_host.c index ce9f27c33..e1af8d801 100644 --- a/src/class/cdc/cdc_host.c +++ b/src/class/cdc/cdc_host.c @@ -973,7 +973,7 @@ static uint32_t ftdi_232bm_baud_to_divisor(uint32_t baud) static bool ftdi_sio_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { uint16_t const divisor = (uint16_t) ftdi_232bm_baud_to_divisor(baudrate); - TU_LOG_DRV("CDC FTDI Set BaudRate = %lu, divisor = 0x%04x\n", baudrate, divisor); + TU_LOG_DRV("CDC FTDI Set BaudRate = %lu, divisor = 0x%04x\r\n", baudrate, divisor); p_cdc->user_control_cb = complete_cb; _ftdi_requested_baud = baudrate; @@ -1108,7 +1108,7 @@ static bool cp210x_ifc_enable(cdch_interface_t* p_cdc, uint16_t enabled, tuh_xfe } static bool cp210x_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { - TU_LOG_DRV("CDC CP210x Set BaudRate = %lu\n", baudrate); + TU_LOG_DRV("CDC CP210x Set BaudRate = %lu\r\n", baudrate); uint32_t baud_le = tu_htole32(baudrate); p_cdc->user_control_cb = complete_cb; return cp210x_set_request(p_cdc, CP210X_SET_BAUDRATE, 0, (uint8_t *) &baud_le, 4, diff --git a/src/class/video/video_device.c b/src/class/video/video_device.c index 91f452afc..16eae0ced 100644 --- a/src/class/video/video_device.c +++ b/src/class/video/video_device.c @@ -609,17 +609,17 @@ static bool _close_vc_itf(uint8_t rhport, videod_interface_t *self) * @param[in] altnum The target alternate setting number. */ static bool _open_vc_itf(uint8_t rhport, videod_interface_t *self, uint_fast8_t altnum) { - TU_LOG2(" open VC %d\n", altnum); + TU_LOG2(" open VC %d\r\n", altnum); uint8_t const *beg = self->beg; uint8_t const *end = beg + self->len; /* The first descriptor is a video control interface descriptor. */ uint8_t const *cur = _find_desc_itf(beg, end, _desc_itfnum(beg), altnum); - TU_LOG2(" cur %d\n", cur - beg); + TU_LOG2(" cur %d\r\n", cur - beg); TU_VERIFY(cur < end); tusb_desc_vc_itf_t const *vc = (tusb_desc_vc_itf_t const *)cur; - TU_LOG2(" bInCollection %d\n", vc->ctl.bInCollection); + TU_LOG2(" bInCollection %d\r\n", vc->ctl.bInCollection); /* Support for up to 2 streaming interfaces only. */ TU_ASSERT(vc->ctl.bInCollection <= CFG_TUD_VIDEO_STREAMING); @@ -628,7 +628,7 @@ static bool _open_vc_itf(uint8_t rhport, videod_interface_t *self, uint_fast8_t /* Advance to the next descriptor after the class-specific VC interface header descriptor. */ cur += vc->std.bLength + vc->ctl.bLength; - TU_LOG2(" bNumEndpoints %d\n", vc->std.bNumEndpoints); + TU_LOG2(" bNumEndpoints %d\r\n", vc->std.bNumEndpoints); /* Open the notification endpoint if it exist. */ if (vc->std.bNumEndpoints) { /* Support for 1 endpoint only. */ @@ -662,7 +662,7 @@ static bool _init_vs_configuration(videod_streaming_interface_t *stm) static bool _open_vs_itf(uint8_t rhport, videod_streaming_interface_t *stm, uint_fast8_t altnum) { uint_fast8_t i; - TU_LOG2(" reopen VS %d\n", altnum); + TU_LOG2(" reopen VS %d\r\n", altnum); uint8_t const *desc = _videod_itf[stm->index_vc].beg; /* Close endpoints of previous settings. */ @@ -672,7 +672,7 @@ static bool _open_vs_itf(uint8_t rhport, videod_streaming_interface_t *stm, uint uint8_t ep_adr = _desc_ep_addr(desc + ofs_ep); usbd_edpt_close(rhport, ep_adr); stm->desc.ep[i] = 0; - TU_LOG2(" close EP%02x\n", ep_adr); + TU_LOG2(" close EP%02x\r\n", ep_adr); } /* clear transfer management information */ @@ -709,12 +709,12 @@ static bool _open_vs_itf(uint8_t rhport, videod_streaming_interface_t *stm, uint } TU_ASSERT(usbd_edpt_open(rhport, ep)); stm->desc.ep[i] = (uint16_t) (cur - desc); - TU_LOG2(" open EP%02x\n", _desc_ep_addr(cur)); + TU_LOG2(" open EP%02x\r\n", _desc_ep_addr(cur)); } if (altnum) { stm->state = VS_STATE_STREAMING; } - TU_LOG2(" done\n"); + TU_LOG2(" done\r\n"); return true; } diff --git a/src/common/tusb_fifo.c b/src/common/tusb_fifo.c index a52c92267..d6c3db4ce 100644 --- a/src/common/tusb_fifo.c +++ b/src/common/tusb_fifo.c @@ -539,7 +539,7 @@ static uint16_t _tu_fifo_write_n(tu_fifo_t* f, const void * data, uint16_t n, tu // Advance index f->wr_idx = advance_index(f->depth, wr_idx, n); - TU_LOG(TU_FIFO_DBG, "\tnew_wr = %u\n", f->wr_idx); + TU_LOG(TU_FIFO_DBG, "\tnew_wr = %u\r\n", f->wr_idx); } _ff_unlock(f->mutex_wr); diff --git a/src/portable/dialog/da146xx/dcd_da146xx.c b/src/portable/dialog/da146xx/dcd_da146xx.c index 961da81d6..d1e85c2df 100644 --- a/src/portable/dialog/da146xx/dcd_da146xx.c +++ b/src/portable/dialog/da146xx/dcd_da146xx.c @@ -651,7 +651,7 @@ static void handle_epx_tx_ev(xfer_ctl_t *xfer) } if (txs & USB_USB_TXS1_REG_USB_TX_URUN_Msk) { - TU_LOG1("EP %d FIFO underrun\n", epnum); + TU_LOG1("EP %d FIFO underrun\r\n", epnum); } // Start next or repeated packet. start_tx_packet(xfer); diff --git a/src/portable/mentor/musb/dcd_musb.c b/src/portable/mentor/musb/dcd_musb.c index 487761847..3c0114e41 100644 --- a/src/portable/mentor/musb/dcd_musb.c +++ b/src/portable/mentor/musb/dcd_musb.c @@ -317,7 +317,7 @@ static bool handle_xfer_in(uint_fast8_t ep_addr) const unsigned mps = regs->TXMAXP; const unsigned len = TU_MIN(mps, rem); void *buf = pipe->buf; - // TU_LOG1(" %p mps %d len %d rem %d\n", buf, mps, len, rem); + // TU_LOG1(" %p mps %d len %d rem %d\r\n", buf, mps, len, rem); if (len) { if (_dcd.pipe_buf_is_fifo[TUSB_DIR_IN] & TU_BIT(epnum_minus1)) { pipe_read_write_packet_ff(buf, &USB0->FIFO1_WORD + epnum_minus1, len, TUSB_DIR_IN); @@ -328,7 +328,7 @@ static bool handle_xfer_in(uint_fast8_t ep_addr) pipe->remaining = rem - len; } regs->TXCSRL = USB_TXCSRL1_TXRDY; - // TU_LOG1(" TXCSRL%d = %x %d\n", epnum_minus1 + 1, regs->TXCSRL, rem - len); + // TU_LOG1(" TXCSRL%d = %x %d\r\n", epnum_minus1 + 1, regs->TXCSRL, rem - len); return false; } @@ -337,7 +337,7 @@ static bool handle_xfer_out(uint_fast8_t ep_addr) unsigned epnum_minus1 = tu_edpt_number(ep_addr) - 1; pipe_state_t *pipe = &_dcd.pipe[tu_edpt_dir(ep_addr)][epnum_minus1]; volatile hw_endpoint_t *regs = edpt_regs(epnum_minus1); - // TU_LOG1(" RXCSRL%d = %x\n", epnum_minus1 + 1, regs->RXCSRL); + // TU_LOG1(" RXCSRL%d = %x\r\n", epnum_minus1 + 1, regs->RXCSRL); TU_ASSERT(regs->RXCSRL & USB_RXCSRL1_RXRDY); @@ -399,14 +399,14 @@ static bool edpt0_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_ * may have already finished and received the next setup packet * without calling this function, so we have no choice but to * invoke the callback function of status packet here. */ - // TU_LOG1(" STATUS OUT USB0->CSRL0 = %x\n", USB0->CSRL0); + // TU_LOG1(" STATUS OUT USB0->CSRL0 = %x\r\n", USB0->CSRL0); _dcd.status_out = 0; if (req == REQUEST_TYPE_INVALID) { dcd_event_xfer_complete(rhport, ep_addr, total_bytes, XFER_RESULT_SUCCESS, false); } else { /* The next setup packet has already been received, it aborts * invoking callback function to avoid confusing TUSB stack. */ - TU_LOG1("Drop CONTROL_STAGE_ACK\n"); + TU_LOG1("Drop CONTROL_STAGE_ACK\r\n"); } return true; } @@ -431,16 +431,16 @@ static bool edpt0_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_ } else { USB0->CSRL0 = USB_CSRL0_TXRDY; /* Flush TX FIFO to return ACK. */ } - // TU_LOG1(" IN USB0->CSRL0 = %x\n", USB0->CSRL0); + // TU_LOG1(" IN USB0->CSRL0 = %x\r\n", USB0->CSRL0); } else { - // TU_LOG1(" OUT USB0->CSRL0 = %x\n", USB0->CSRL0); + // TU_LOG1(" OUT USB0->CSRL0 = %x\r\n", USB0->CSRL0); _dcd.pipe0.buf = buffer; _dcd.pipe0.length = len; _dcd.pipe0.remaining = len; USB0->CSRL0 = USB_CSRL0_RXRDYC; /* Clear RX FIFO to return ACK. */ } } else if (dir_in) { - // TU_LOG1(" STATUS IN USB0->CSRL0 = %x\n", USB0->CSRL0); + // TU_LOG1(" STATUS IN USB0->CSRL0 = %x\r\n", USB0->CSRL0); _dcd.pipe0.buf = NULL; _dcd.pipe0.length = 0; _dcd.pipe0.remaining = 0; @@ -454,7 +454,7 @@ static void process_ep0(uint8_t rhport) { uint_fast8_t csrl = USB0->CSRL0; - // TU_LOG1(" EP0 USB0->CSRL0 = %x\n", csrl); + // TU_LOG1(" EP0 USB0->CSRL0 = %x\r\n", csrl); if (csrl & USB_CSRL0_STALLED) { /* Returned STALL packet to HOST. */ @@ -464,7 +464,7 @@ static void process_ep0(uint8_t rhport) unsigned req = _dcd.setup_packet.bmRequestType; if (csrl & USB_CSRL0_SETEND) { - TU_LOG1(" ABORT by the next packets\n"); + TU_LOG1(" ABORT by the next packets\r\n"); USB0->CSRL0 = USB_CSRL0_SETENDC; if (req != REQUEST_TYPE_INVALID && _dcd.pipe0.buf) { /* DATA stage was aborted by receiving STATUS or SETUP packet. */ @@ -539,14 +539,14 @@ static void process_edpt_n(uint8_t rhport, uint_fast8_t ep_addr) volatile hw_endpoint_t *regs = edpt_regs(epn_minus1); if (dir_in) { - // TU_LOG1(" TXCSRL%d = %x\n", epn_minus1 + 1, regs->TXCSRL); + // TU_LOG1(" TXCSRL%d = %x\r\n", epn_minus1 + 1, regs->TXCSRL); if (regs->TXCSRL & USB_TXCSRL1_STALLED) { regs->TXCSRL &= ~(USB_TXCSRL1_STALLED | USB_TXCSRL1_UNDRN); return; } completed = handle_xfer_in(ep_addr); } else { - // TU_LOG1(" RXCSRL%d = %x\n", epn_minus1 + 1, regs->RXCSRL); + // TU_LOG1(" RXCSRL%d = %x\r\n", epn_minus1 + 1, regs->RXCSRL); if (regs->RXCSRL & USB_RXCSRL1_STALLED) { regs->RXCSRL &= ~(USB_RXCSRL1_STALLED | USB_RXCSRL1_OVER); return; @@ -789,7 +789,7 @@ bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t t { (void)rhport; bool ret; - // TU_LOG1("X %x %d\n", ep_addr, total_bytes); + // TU_LOG1("X %x %d\r\n", ep_addr, total_bytes); unsigned const epnum = tu_edpt_number(ep_addr); unsigned const ie = NVIC_GetEnableIRQ(USB0_IRQn); NVIC_DisableIRQ(USB0_IRQn); @@ -807,7 +807,7 @@ bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16_ { (void)rhport; bool ret; - // TU_LOG1("X %x %d\n", ep_addr, total_bytes); + // TU_LOG1("X %x %d\r\n", ep_addr, total_bytes); unsigned const epnum = tu_edpt_number(ep_addr); TU_ASSERT(epnum); unsigned const ie = NVIC_GetEnableIRQ(USB0_IRQn); @@ -869,7 +869,7 @@ void dcd_int_handler(uint8_t rhport) is = USB0->IS; /* read and clear interrupt status */ txis = USB0->TXIS; /* read and clear interrupt status */ rxis = USB0->RXIS; /* read and clear interrupt status */ - // TU_LOG1("D%2x T%2x R%2x\n", is, txis, rxis); + // TU_LOG1("D%2x T%2x R%2x\r\n", is, txis, rxis); is &= USB0->IE; /* Clear disabled interrupts */ if (is & USB_IS_DISCON) { diff --git a/src/portable/mentor/musb/hcd_musb.c b/src/portable/mentor/musb/hcd_musb.c index 9eb2e005e..7e67b8291 100644 --- a/src/portable/mentor/musb/hcd_musb.c +++ b/src/portable/mentor/musb/hcd_musb.c @@ -418,7 +418,7 @@ static void process_ep0(uint8_t rhport) (void)rhport; uint_fast8_t csrl = USB0->CSRL0; - // TU_LOG1(" EP0 CSRL = %x\n", csrl); + // TU_LOG1(" EP0 CSRL = %x\r\n", csrl); unsigned const dev_addr = USB0->TXFUNCADDR0; unsigned const req = _hcd.bmRequestType; @@ -508,7 +508,7 @@ static void process_pipe_tx(uint8_t rhport, uint_fast8_t pipenum) volatile hw_endpoint_t *regs = edpt_regs(pipenum - 1); unsigned const csrl = regs->TXCSRL; - // TU_LOG1(" TXCSRL%d = %x\n", pipenum, csrl); + // TU_LOG1(" TXCSRL%d = %x\r\n", pipenum, csrl); if (csrl & (USB_TXCSRL1_STALLED | USB_TXCSRL1_ERROR)) { if (csrl & USB_TXCSRL1_TXRDY) regs->TXCSRL = (csrl & ~(USB_TXCSRL1_STALLED | USB_TXCSRL1_ERROR)) | USB_TXCSRL1_FLUSH; @@ -537,7 +537,7 @@ static void process_pipe_rx(uint8_t rhport, uint_fast8_t pipenum) volatile hw_endpoint_t *regs = edpt_regs(pipenum - 1); unsigned const csrl = regs->RXCSRL; - // TU_LOG1(" RXCSRL%d = %x\n", pipenum, csrl); + // TU_LOG1(" RXCSRL%d = %x\r\n", pipenum, csrl); if (csrl & (USB_RXCSRL1_STALLED | USB_RXCSRL1_ERROR)) { if (csrl & USB_RXCSRL1_RXRDY) regs->RXCSRL = (csrl & ~(USB_RXCSRL1_STALLED | USB_RXCSRL1_ERROR)) | USB_RXCSRL1_FLUSH; @@ -846,7 +846,7 @@ void hcd_int_handler(uint8_t rhport) is = USB0->IS; /* read and clear interrupt status */ txis = USB0->TXIS; /* read and clear interrupt status */ rxis = USB0->RXIS; /* read and clear interrupt status */ - // TU_LOG1("D%2x T%2x R%2x\n", is, txis, rxis); + // TU_LOG1("D%2x T%2x R%2x\r\n", is, txis, rxis); is &= USB0->IE; /* Clear disabled interrupts */ if (is & USB_IS_RESUME) { diff --git a/src/portable/nxp/khci/hcd_khci.c b/src/portable/nxp/khci/hcd_khci.c index f6029ee0d..fb978cac8 100644 --- a/src/portable/nxp/khci/hcd_khci.c +++ b/src/portable/nxp/khci/hcd_khci.c @@ -161,7 +161,7 @@ static int prepare_packets(int pipenum) buffer_descriptor_t *bd = _hcd.bdt[dir_tx]; TU_ASSERT(0 == bd[odd].own, -1); - // TU_LOG1(" %p dir %d odd %d data %d\n", &bd[odd], dir_tx, odd, pipe->data); + // TU_LOG1(" %p dir %d odd %d data %d\r\n", &bd[odd], dir_tx, odd, pipe->data); ep->pipenum = pipenum; @@ -251,7 +251,7 @@ static bool resume_transfer(int pipenum) flags |= USB_ENDPT_EPHSHK_MASK | USB_ENDPT_EPCTLDIS_MASK | USB_ENDPT_RETRYDIS_MASK; break; } - // TU_LOG1(" resume pipenum %d flags %x\n", pipenum, flags); + // TU_LOG1(" resume pipenum %d flags %x\r\n", pipenum, flags); KHCI->ENDPOINT[0].ENDPT = flags; KHCI->ADDR = (KHCI->ADDR & USB_ADDR_LSEN_MASK) | pipe->dev_addr; @@ -302,7 +302,7 @@ static void process_tokdne(uint8_t rhport) int pipenum = ep->pipenum; int next_pipenum; - // TU_LOG1("TOKDNE %x PID %x pipe %d\n", s, pid, pipenum); + // TU_LOG1("TOKDNE %x PID %x pipe %d\r\n", s, pid, pipenum); xfer_result_t result; switch (pid) { @@ -479,7 +479,7 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { (void)rhport; - // TU_LOG1("SETUP %u\n", dev_addr); + // TU_LOG1("SETUP %u\r\n", dev_addr); TU_ASSERT(0 == (_hcd.in_progress & TU_BIT(0))); int pipenum = find_pipe(dev_addr, 0); @@ -510,7 +510,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const { (void)rhport; uint8_t const ep_addr = ep_desc->bEndpointAddress; - // TU_LOG1("O %u %x\n", dev_addr, ep_addr); + // TU_LOG1("O %u %x\r\n", dev_addr, ep_addr); /* Find a free pipe */ pipe_state_t *p = &_hcd.pipe[0]; pipe_state_t *end = &_hcd.pipe[CFG_TUH_ENDPOINT_MAX * 2]; @@ -543,7 +543,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { (void)rhport; - // TU_LOG1("X %u %x %x %d\n", dev_addr, ep_addr, (uintptr_t)buffer, buflen); + // TU_LOG1("X %u %x %x %d\r\n", dev_addr, ep_addr, (uintptr_t)buffer, buflen); int pipenum = find_pipe(dev_addr, ep_addr); TU_ASSERT(0 <= pipenum); @@ -580,7 +580,7 @@ void hcd_int_handler(uint8_t rhport) uint32_t is = KHCI->ISTAT; uint32_t msk = KHCI->INTEN; - // TU_LOG1("S %lx\n", is); + // TU_LOG1("S %lx\r\n", is); /* clear disabled interrupts */ KHCI->ISTAT = (is & ~msk & ~USB_ISTAT_TOKDNE_MASK) | USB_ISTAT_SOFTOK_MASK; @@ -589,7 +589,7 @@ void hcd_int_handler(uint8_t rhport) if (is & USB_ISTAT_ERROR_MASK) { unsigned err = KHCI->ERRSTAT; if (err) { - TU_LOG1(" ERR %x\n", err); + TU_LOG1(" ERR %x\r\n", err); KHCI->ERRSTAT = err; } else { KHCI->INTEN &= ~USB_ISTAT_ERROR_MASK; diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 02f9968a7..51b8bf72d 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -219,7 +219,7 @@ static void __tusb_irq_path_func(hcd_rp2040_irq)(void) if ( status & USB_INTS_BUFF_STATUS_BITS ) { handled |= USB_INTS_BUFF_STATUS_BITS; - TU_LOG(2, "Buffer complete\n"); + TU_LOG(2, "Buffer complete\r\n"); hw_handle_buff_status(); } @@ -227,7 +227,7 @@ static void __tusb_irq_path_func(hcd_rp2040_irq)(void) { handled |= USB_INTS_TRANS_COMPLETE_BITS; usb_hw_clear->sie_status = USB_SIE_STATUS_TRANS_COMPLETE_BITS; - TU_LOG(2, "Transfer complete\n"); + TU_LOG(2, "Transfer complete\r\n"); hw_trans_complete(); } diff --git a/src/portable/raspberrypi/rp2040/rp2040_usb.c b/src/portable/raspberrypi/rp2040/rp2040_usb.c index 1f49665ff..53486a586 100644 --- a/src/portable/raspberrypi/rp2040/rp2040_usb.c +++ b/src/portable/raspberrypi/rp2040/rp2040_usb.c @@ -219,7 +219,7 @@ void hw_endpoint_xfer_start(struct hw_endpoint *ep, uint8_t *buffer, uint16_t to if ( ep->active ) { // TODO: Is this acceptable for interrupt packets? - TU_LOG(1, "WARN: starting new transfer on already active ep %d %s\n", tu_edpt_number(ep->ep_addr), + TU_LOG(1, "WARN: starting new transfer on already active ep %d %s\r\n", tu_edpt_number(ep->ep_addr), ep_dir_string[tu_edpt_dir(ep->ep_addr)]); hw_endpoint_reset_transfer(ep); @@ -419,7 +419,7 @@ static bool __tusb_irq_path_func(e15_is_critical_frame_period) (struct hw_endpoi if (delta < 800 || delta > 998) { return false; } - TU_LOG(3, "Avoiding sof %lu now %lu last %lu\n", (usb_hw->sof_rd + 1) & USB_SOF_RD_BITS, time_us_32(), e15_last_sof); + TU_LOG(3, "Avoiding sof %lu now %lu last %lu\r\n", (usb_hw->sof_rd + 1) & USB_SOF_RD_BITS, time_us_32(), e15_last_sof); return true; } diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 0e6fa1618..886a6f6b8 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -409,7 +409,7 @@ static void process_pipe_nrdy(uint8_t rhport, unsigned num) (void)rhport; xfer_result_t result; uint16_t volatile *ctr = get_pipectr(num); - // TU_LOG1("NRDY %d %x\n", num, *ctr); + // TU_LOG1("NRDY %d %x\r\n", num, *ctr); switch (*ctr & RUSB2_PIPE_CTR_PID_Msk) { default: return; case RUSB2_PIPE_CTR_PID_STALL: result = XFER_RESULT_STALLED; break; @@ -608,7 +608,7 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { (void)rhport; - // TU_LOG1("S %d %x\n", dev_addr, RUSB2->DCPCTR); + // TU_LOG1("S %d %x\r\n", dev_addr, RUSB2->DCPCTR); TU_ASSERT(dev_addr < 6); /* USBa can only handle addresses from 0 to 5. */ TU_ASSERT(0 == RUSB2->DCPCTR_b.SUREQ); @@ -701,7 +701,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t *b { bool r; hcd_int_disable(rhport); - // TU_LOG1("X %d %x %u\n", dev_addr, ep_addr, buflen); + // TU_LOG1("X %d %x %u\r\n", dev_addr, ep_addr, buflen); r = process_edpt_xfer(dev_addr, ep_addr, buffer, buflen); hcd_int_enable(rhport); return r; @@ -745,7 +745,7 @@ void hcd_int_handler(uint8_t rhport) /* clear active bits except VALID (don't write 0 to already cleared bits according to the HW manual) */ RUSB2->INTSTS1 = ~((RUSB2_INTSTS1_SACK_Msk | RUSB2_INTSTS1_SIGN_Msk | RUSB2_INTSTS1_ATTCH_Msk | RUSB2_INTSTS1_DTCH_Msk) & is1); RUSB2->INTSTS0 = ~((RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_NRDY_Msk | RUSB2_INTSTS0_BEMP_Msk) & is0); - // TU_LOG1("IS %04x %04x\n", is0, is1); + // TU_LOG1("IS %04x %04x\r\n", is0, is1); is1 &= RUSB2->INTENB1; is0 &= RUSB2->INTENB0; diff --git a/src/portable/st/typec/typec_stm32.c b/src/portable/st/typec/typec_stm32.c index bf8b660f0..8da2e39ba 100644 --- a/src/portable/st/typec/typec_stm32.c +++ b/src/portable/st/typec/typec_stm32.c @@ -246,7 +246,7 @@ void tcd_int_handler(uint8_t rhport) { v_cc[0] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC1_Pos) & 0x03; v_cc[1] = (UCPD1->SR >> UCPD_SR_TYPEC_VSTATE_CC2_Pos) & 0x03; - TU_LOG3("VState CC1 = %lu, CC2 = %lu\n", v_cc[0], v_cc[1]); + TU_LOG3("VState CC1 = %lu, CC2 = %lu\r\n", v_cc[0], v_cc[1]); uint32_t cr = UCPD1->CR; @@ -255,15 +255,15 @@ void tcd_int_handler(uint8_t rhport) { // FIXME somehow CC2 is vstate is not correct, always 1 even not attached. // on DPOW1 board, it is connected to PA10 (USBPD_DBCC2), we probably miss something. if ((sr & UCPD_SR_TYPECEVT1) && (v_cc[0] == 3)) { - TU_LOG3("Attach CC1\n"); + TU_LOG3("Attach CC1\r\n"); cr &= ~(UCPD_CR_PHYCCSEL | UCPD_CR_CCENABLE); cr |= UCPD_CR_PHYRXEN | UCPD_CR_CCENABLE_0; } else if ((sr & UCPD_SR_TYPECEVT2) && (v_cc[1] == 3)) { - TU_LOG3("Attach CC2\n"); + TU_LOG3("Attach CC2\r\n"); cr &= ~UCPD_CR_CCENABLE; cr |= (UCPD_CR_PHYCCSEL | UCPD_CR_PHYRXEN | UCPD_CR_CCENABLE_1); } else { - TU_LOG3("Detach\n"); + TU_LOG3("Detach\r\n"); cr &= ~UCPD_CR_PHYRXEN; cr |= UCPD_CR_CCENABLE_0 | UCPD_CR_CCENABLE_1; } @@ -290,7 +290,7 @@ void tcd_int_handler(uint8_t rhport) { //------------- RX -------------// if (sr & UCPD_SR_RXORDDET) { // SOP: Start of Packet. - TU_LOG3("SOP\n"); + TU_LOG3("SOP\r\n"); // UCPD1->RX_ORDSET & UCPD_RX_ORDSET_RXORDSET_Msk; // ack @@ -299,7 +299,7 @@ void tcd_int_handler(uint8_t rhport) { // Received full message if (sr & UCPD_SR_RXMSGEND) { - TU_LOG3("RX MSG END\n"); + TU_LOG3("RX MSG END\r\n"); // stop TX dma_stop(rhport, true); @@ -328,7 +328,7 @@ void tcd_int_handler(uint8_t rhport) { } if (sr & UCPD_SR_RXOVR) { - TU_LOG3("RXOVR\n"); + TU_LOG3("RXOVR\r\n"); // ack UCPD1->ICR = UCPD_ICR_RXOVRCF; } @@ -343,12 +343,12 @@ void tcd_int_handler(uint8_t rhport) { uint8_t result; if ( sr & UCPD_SR_TXMSGSENT ) { - TU_LOG3("TX MSG SENT\n"); + TU_LOG3("TX MSG SENT\r\n"); result = XFER_RESULT_SUCCESS; // ack UCPD1->ICR = UCPD_ICR_TXMSGSENTCF; }else { - TU_LOG3("TX Error\n"); + TU_LOG3("TX Error\r\n"); result = XFER_RESULT_FAILED; // ack UCPD1->ICR = UCPD_SR_TXMSGDISC | UCPD_SR_TXMSGABT | UCPD_SR_TXUND; diff --git a/src/portable/sunxi/dcd_sunxi_musb.c b/src/portable/sunxi/dcd_sunxi_musb.c index e26be775d..6cc1975a8 100644 --- a/src/portable/sunxi/dcd_sunxi_musb.c +++ b/src/portable/sunxi/dcd_sunxi_musb.c @@ -408,9 +408,9 @@ static inline unsigned free_block_size(free_block_t const *blk) #if 0 static inline void print_block_list(free_block_t const *blk, unsigned num) { - TU_LOG1("*************\n"); + TU_LOG1("*************\r\n"); for (unsigned i = 0; i < num; ++i) { - TU_LOG1(" Blk%u %u %u\n", i, blk->beg, blk->end); + TU_LOG1(" Blk%u %u %u\r\n", i, blk->beg, blk->end); ++blk; } } @@ -590,7 +590,7 @@ static bool handle_xfer_in(uint_fast8_t ep_addr) const unsigned mps = USBC_Readw(USBC_REG_TXMAXP(USBC0_BASE)); const unsigned len = TU_MIN(mps, rem); uint8_t *buf = pipe->buf; - // TU_LOG1(" %p mps %d len %d rem %d\n", buf, mps, len, rem); + // TU_LOG1(" %p mps %d len %d rem %d\r\n", buf, mps, len, rem); if (len) { volatile void* addr = (volatile void*)(USBC_REG_EPFIFO1(USBC0_BASE) + (epnum_minus1 << 2)); if (_dcd.pipe_buf_is_fifo[TUSB_DIR_IN] & TU_BIT(epnum_minus1)) { @@ -602,7 +602,7 @@ static bool handle_xfer_in(uint_fast8_t ep_addr) pipe->remaining = rem - len; } __USBC_Dev_Tx_WriteDataComplete(); - // TU_LOG1(" TXCSRL%d = %x %d\n", epnum_minus1 + 1, regs->TXCSRL, rem - len); + // TU_LOG1(" TXCSRL%d = %x %d\r\n", epnum_minus1 + 1, regs->TXCSRL, rem - len); return false; } @@ -610,7 +610,7 @@ static bool handle_xfer_out(uint_fast8_t ep_addr) { unsigned epnum_minus1 = tu_edpt_number(ep_addr) - 1; pipe_state_t *pipe = &_dcd.pipe[tu_edpt_dir(ep_addr)][epnum_minus1]; - // TU_LOG1(" RXCSRL%d = %x\n", epnum_minus1 + 1, regs->RXCSRL); + // TU_LOG1(" RXCSRL%d = %x\r\n", epnum_minus1 + 1, regs->RXCSRL); TU_ASSERT(__USBC_Dev_Rx_IsReadDataReady()); @@ -677,14 +677,14 @@ static bool edpt0_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_ * may have already finished and received the next setup packet * without calling this function, so we have no choice but to * invoke the callback function of status packet here. */ - // TU_LOG1(" STATUS OUT CSRL0 = %x\n", CSRL0); + // TU_LOG1(" STATUS OUT CSRL0 = %x\r\n", CSRL0); _dcd.status_out = 0; if (req == REQUEST_TYPE_INVALID) { dcd_event_xfer_complete(rhport, ep_addr, total_bytes, XFER_RESULT_SUCCESS, false); } else { /* The next setup packet has already been received, it aborts * invoking callback function to avoid confusing TUSB stack. */ - TU_LOG1("Drop CONTROL_STAGE_ACK\n"); + TU_LOG1("Drop CONTROL_STAGE_ACK\r\n"); } return true; } @@ -709,16 +709,16 @@ static bool edpt0_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_ } else { __USBC_Dev_ep0_WriteDataHalf(); } - // TU_LOG1(" IN CSRL0 = %x\n", CSRL0); + // TU_LOG1(" IN CSRL0 = %x\r\n", CSRL0); } else { - // TU_LOG1(" OUT CSRL0 = %x\n", CSRL0); + // TU_LOG1(" OUT CSRL0 = %x\r\n", CSRL0); _dcd.pipe0.buf = buffer; _dcd.pipe0.length = len; _dcd.pipe0.remaining = len; __USBC_Dev_ep0_ReadDataHalf(); } } else if (dir_in) { - // TU_LOG1(" STATUS IN CSRL0 = %x\n", CSRL0); + // TU_LOG1(" STATUS IN CSRL0 = %x\r\n", CSRL0); _dcd.pipe0.buf = NULL; _dcd.pipe0.length = 0; _dcd.pipe0.remaining = 0; @@ -733,7 +733,7 @@ static void process_ep0(uint8_t rhport) USBC_SelectActiveEp(0); uint_fast8_t csrl = USBC_Readw(USBC_REG_CSR0(USBC0_BASE)); - // TU_LOG1(" EP0 CSRL0 = %x\n", csrl); + // TU_LOG1(" EP0 CSRL0 = %x\r\n", csrl); if (csrl & USB_CSRL0_STALLED) { /* Returned STALL packet to HOST. */ @@ -743,7 +743,7 @@ static void process_ep0(uint8_t rhport) unsigned req = _dcd.setup_packet.bmRequestType; if (csrl & USB_CSRL0_SETEND) { - // TU_LOG1(" ABORT by the next packets\n"); + // TU_LOG1(" ABORT by the next packets\r\n"); USBC_Dev_Ctrl_ClearSetupEnd(); if (req != REQUEST_TYPE_INVALID && _dcd.pipe0.buf) { /* DATA stage was aborted by receiving STATUS or SETUP packet. */ @@ -819,14 +819,14 @@ static void process_edpt_n(uint8_t rhport, uint_fast8_t ep_addr) USBC_SelectActiveEp(epn); if (dir_in) { - // TU_LOG1(" TXCSRL%d = %x\n", epn_minus1 + 1, regs->TXCSRL); + // TU_LOG1(" TXCSRL%d = %x\r\n", epn_minus1 + 1, regs->TXCSRL); if (__USBC_Dev_Tx_IsEpStall()) { __USBC_Dev_Tx_ClearStall(); return; } completed = handle_xfer_in(ep_addr); } else { - // TU_LOG1(" RXCSRL%d = %x\n", epn_minus1 + 1, regs->RXCSRL); + // TU_LOG1(" RXCSRL%d = %x\r\n", epn_minus1 + 1, regs->RXCSRL); if (__USBC_Dev_Rx_IsEpStall()) { __USBC_Dev_Rx_ClearStall(); return; @@ -1092,7 +1092,7 @@ bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t t { (void)rhport; bool ret; - // TU_LOG1("X %x %d\n", ep_addr, total_bytes); + // TU_LOG1("X %x %d\r\n", ep_addr, total_bytes); unsigned const epnum = tu_edpt_number(ep_addr); musb_int_mask(); @@ -1111,7 +1111,7 @@ bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16_ { (void)rhport; bool ret; - // TU_LOG1("X %x %d\n", ep_addr, total_bytes); + // TU_LOG1("X %x %d\r\n", ep_addr, total_bytes); unsigned const epnum = tu_edpt_number(ep_addr); TU_ASSERT(epnum); -- cgit v1.3.1 From 2029ca9536e7e889f0f420218136e7bd1ac091fc Mon Sep 17 00:00:00 2001 From: Lars Pötter Date: Sun, 2 Jul 2023 10:53:08 +0200 Subject: also fixed pico_trac() log messages. --- src/portable/raspberrypi/pio_usb/hcd_pio_usb.c | 4 ++-- src/portable/raspberrypi/rp2040/dcd_rp2040.c | 6 +++--- src/portable/raspberrypi/rp2040/rp2040_usb.c | 4 ++-- 3 files changed, 7 insertions(+), 7 deletions(-) (limited to 'src/portable') diff --git a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c index 264af2e7a..130716da4 100644 --- a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c +++ b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c @@ -150,11 +150,11 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet // // so if any transfer is active on epx, we are busy. Interrupt endpoints have their own // // EPX so ep->active will only be busy if there is a pending transfer on that interrupt endpoint // // on that device -// pico_trace("hcd_edpt_busy dev addr %d ep_addr 0x%x\n", dev_addr, ep_addr); +// pico_trace("hcd_edpt_busy dev addr %d ep_addr 0x%x\r\n", dev_addr, ep_addr); // struct hw_endpoint *ep = get_dev_ep(dev_addr, ep_addr); // assert(ep); // bool busy = ep->active; -// pico_trace("busy == %d\n", busy); +// pico_trace("busy == %d\r\n", busy); // return busy; //} diff --git a/src/portable/raspberrypi/rp2040/dcd_rp2040.c b/src/portable/raspberrypi/rp2040/dcd_rp2040.c index 479b17b67..e8cee73fd 100644 --- a/src/portable/raspberrypi/rp2040/dcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/dcd_rp2040.c @@ -189,7 +189,7 @@ static void hw_endpoint_xfer(uint8_t ep_addr, uint8_t *buffer, uint16_t total_by static void __tusb_irq_path_func(hw_handle_buff_status)(void) { uint32_t remaining_buffers = usb_hw->buf_status; - pico_trace("buf_status = 0x%08lx\n", remaining_buffers); + pico_trace("buf_status = 0x%08lx\r\n", remaining_buffers); uint bit = 1u; for (uint8_t i = 0; remaining_buffers && i < USB_MAX_ENDPOINTS * 2; i++) { @@ -331,7 +331,7 @@ static void __tusb_irq_path_func(dcd_rp2040_irq)(void) // SE0 for 2.5 us or more (will last at least 10ms) if ( status & USB_INTS_BUS_RESET_BITS ) { - pico_trace("BUS RESET\n"); + pico_trace("BUS RESET\r\n"); handled |= USB_INTS_BUS_RESET_BITS; @@ -565,7 +565,7 @@ void dcd_edpt_close (uint8_t rhport, uint8_t ep_addr) { (void) rhport; - pico_trace("dcd_edpt_close %02x\n", ep_addr); + pico_trace("dcd_edpt_close %02x\r\n", ep_addr); hw_endpoint_close(ep_addr); } diff --git a/src/portable/raspberrypi/rp2040/rp2040_usb.c b/src/portable/raspberrypi/rp2040/rp2040_usb.c index 53486a586..a512dc34f 100644 --- a/src/portable/raspberrypi/rp2040/rp2040_usb.c +++ b/src/portable/raspberrypi/rp2040/rp2040_usb.c @@ -276,7 +276,7 @@ static uint16_t __tusb_irq_path_func(sync_ep_buffer)(struct hw_endpoint *ep, uin // Short packet if (xferred_bytes < ep->wMaxPacketSize) { - pico_trace(" Short packet on buffer %d with %u bytes\n", buf_id, xferred_bytes); + pico_trace(" Short packet on buffer %d with %u bytes\r\n", buf_id, xferred_bytes); // Reduce total length as this is last packet ep->remaining_len = 0; } @@ -352,7 +352,7 @@ bool __tusb_irq_path_func(hw_endpoint_xfer_continue)(struct hw_endpoint *ep) // If we are done then notify tinyusb if (ep->remaining_len == 0) { - pico_trace("Completed transfer of %d bytes on ep %d %s\n", + pico_trace("Completed transfer of %d bytes on ep %d %s\r\n", ep->xferred_len, tu_edpt_number(ep->ep_addr), ep_dir_string[tu_edpt_dir(ep->ep_addr)]); // Notify caller we are done so it can notify the tinyusb stack hw_endpoint_lock_update(ep, -1); -- cgit v1.3.1 From f79529c09c6e7c0d6ee5586633ceb8c83e345406 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 5 Jul 2023 17:13:01 +0700 Subject: usb hs work with ra 6m5 ek --- .idea/runConfigurations/ra4m1.xml | 10 ++ .idea/runConfigurations/ra6m1.xml | 10 ++ .idea/runConfigurations/ra6m5.xml | 10 ++ hw/bsp/ra/board_cfg.h | 45 +++++++++ hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp/bsp_cfg.h | 4 +- hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp/bsp_cfg.h | 4 +- hw/bsp/ra/boards/ra6m1_ek/fsp_cfg/bsp/bsp_cfg.h | 4 +- hw/bsp/ra/boards/ra6m5_ek/board.cmake | 20 +++- hw/bsp/ra/boards/ra6m5_ek/fsp_cfg/bsp/bsp_cfg.h | 4 +- hw/bsp/ra/family.c | 118 ++++++++++++++++-------- hw/bsp/ra/vector_data.h | 15 ++- src/common/tusb_mcu.h | 1 + src/portable/renesas/rusb2/dcd_rusb2.c | 3 +- 13 files changed, 188 insertions(+), 60 deletions(-) create mode 100644 .idea/runConfigurations/ra4m1.xml create mode 100644 .idea/runConfigurations/ra6m1.xml create mode 100644 .idea/runConfigurations/ra6m5.xml create mode 100644 hw/bsp/ra/board_cfg.h (limited to 'src/portable') diff --git a/.idea/runConfigurations/ra4m1.xml b/.idea/runConfigurations/ra4m1.xml new file mode 100644 index 000000000..22bb61949 --- /dev/null +++ b/.idea/runConfigurations/ra4m1.xml @@ -0,0 +1,10 @@ + + + + + + + + + \ No newline at end of file diff --git a/.idea/runConfigurations/ra6m1.xml b/.idea/runConfigurations/ra6m1.xml new file mode 100644 index 000000000..438ac4063 --- /dev/null +++ b/.idea/runConfigurations/ra6m1.xml @@ -0,0 +1,10 @@ + + + + + + + + + \ No newline at end of file diff --git a/.idea/runConfigurations/ra6m5.xml b/.idea/runConfigurations/ra6m5.xml new file mode 100644 index 000000000..02df11610 --- /dev/null +++ b/.idea/runConfigurations/ra6m5.xml @@ -0,0 +1,10 @@ + + + + + + + + + \ No newline at end of file diff --git a/hw/bsp/ra/board_cfg.h b/hw/bsp/ra/board_cfg.h new file mode 100644 index 000000000..baed46b5f --- /dev/null +++ b/hw/bsp/ra/board_cfg.h @@ -0,0 +1,45 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + */ + +#ifndef _BOARD_CFG_H +#define _BOARD_CFG_H + +#ifdef __cplusplus +extern "C" { +#endif + +#if defined(BSP_MCU_GROUP_RA6M5) || defined(BSP_MCU_GROUP_RA6M3) || (BSP_CFG_MCU_PART_SERIES == 8) + #define BOARD_HAS_USB_HIGHSPEED +#endif + +// for SystemInit() +void bsp_init(void * p_args); + + +#ifdef __cplusplus +} +#endif + +#endif diff --git a/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp/bsp_cfg.h b/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp/bsp_cfg.h index 19bb473eb..f0577b702 100644 --- a/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp/bsp_cfg.h +++ b/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp/bsp_cfg.h @@ -4,6 +4,7 @@ #include "bsp_clock_cfg.h" #include "bsp_mcu_family_cfg.h" +#include "board_cfg.h" #undef RA_NOT_DEFINED #define BSP_CFG_RTOS (0) @@ -31,7 +32,4 @@ #define BSP_CLOCK_CFG_SUBCLOCK_POPULATED (1) #define BSP_CLOCK_CFG_SUBCLOCK_STABILIZATION_MS 1000 -// for SystemInit() -void bsp_init(void * p_args); - #endif /* BSP_CFG_H_ */ diff --git a/hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp/bsp_cfg.h b/hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp/bsp_cfg.h index 6a47bccc6..47de7747d 100644 --- a/hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp/bsp_cfg.h +++ b/hw/bsp/ra/boards/ra4m3_ek/fsp_cfg/bsp/bsp_cfg.h @@ -7,6 +7,7 @@ extern "C" { #include "bsp_clock_cfg.h" #include "bsp_mcu_family_cfg.h" +#include "board_cfg.h" #define RA_NOT_DEFINED 0 #ifndef BSP_CFG_RTOS @@ -56,9 +57,6 @@ extern "C" { #define BSP_CLOCK_CFG_SUBCLOCK_STABILIZATION_MS 1000 #endif -// for SystemInit() -void bsp_init(void * p_args); - #ifdef __cplusplus } #endif diff --git a/hw/bsp/ra/boards/ra6m1_ek/fsp_cfg/bsp/bsp_cfg.h b/hw/bsp/ra/boards/ra6m1_ek/fsp_cfg/bsp/bsp_cfg.h index 75a331fc2..b5ed53a3b 100644 --- a/hw/bsp/ra/boards/ra6m1_ek/fsp_cfg/bsp/bsp_cfg.h +++ b/hw/bsp/ra/boards/ra6m1_ek/fsp_cfg/bsp/bsp_cfg.h @@ -8,6 +8,7 @@ extern "C" { #include "bsp_clock_cfg.h" #include "bsp_mcu_family_cfg.h" +#include "board_cfg.h" #define RA_NOT_DEFINED 0 #ifndef BSP_CFG_RTOS @@ -60,9 +61,6 @@ extern "C" { #define BSP_CLOCK_CFG_SUBCLOCK_STABILIZATION_MS 1000 #endif -// for SystemInit() -void bsp_init(void * p_args); - #ifdef __cplusplus } #endif diff --git a/hw/bsp/ra/boards/ra6m5_ek/board.cmake b/hw/bsp/ra/boards/ra6m5_ek/board.cmake index 42a4c7417..d934a0c0d 100644 --- a/hw/bsp/ra/boards/ra6m5_ek/board.cmake +++ b/hw/bsp/ra/boards/ra6m5_ek/board.cmake @@ -3,8 +3,22 @@ set(MCU_VARIANT ra6m5) set(JLINK_DEVICE R7FA6M5BH) +# default to PORT1 Highspeed +if (NOT DEFINED PORT) +set(PORT 1) +endif() + function(update_board TARGET) -# target_compile_definitions(${TARGET} PUBLIC) -# target_sources(${TARGET} PRIVATE) -# target_include_directories(${BOARD_TARGET} PUBLIC) + target_compile_definitions(${TARGET} PUBLIC + BOARD_TUD_RHPORT=${PORT} + # port 0 is fullspeed, port 1 is highspeed + BOARD_TUD_MAX_SPEED=$ + ) + + if (PORT STREQUAL 1) + target_compile_definitions(${TARGET} PUBLIC + CFG_TUSB_RHPORT1_MODE=OPT_MODE_DEVICE|OPT_MODE_HIGH_SPEED + CFG_TUSB_RHPORT0_MODE=0 + ) + endif () endfunction() diff --git a/hw/bsp/ra/boards/ra6m5_ek/fsp_cfg/bsp/bsp_cfg.h b/hw/bsp/ra/boards/ra6m5_ek/fsp_cfg/bsp/bsp_cfg.h index e41f603ad..a41536eda 100644 --- a/hw/bsp/ra/boards/ra6m5_ek/fsp_cfg/bsp/bsp_cfg.h +++ b/hw/bsp/ra/boards/ra6m5_ek/fsp_cfg/bsp/bsp_cfg.h @@ -7,6 +7,7 @@ extern "C" { #include "bsp_clock_cfg.h" #include "bsp_mcu_family_cfg.h" +#include "board_cfg.h" #define RA_NOT_DEFINED 0 #ifndef BSP_CFG_RTOS @@ -56,9 +57,6 @@ extern "C" { #define BSP_CLOCK_CFG_SUBCLOCK_STABILIZATION_MS 1000 #endif -// for SystemInit() -void bsp_init(void * p_args); - #ifdef __cplusplus } #endif diff --git a/hw/bsp/ra/family.c b/hw/bsp/ra/family.c index 769678954..36b46beab 100644 --- a/hw/bsp/ra/family.c +++ b/hw/bsp/ra/family.c @@ -48,9 +48,9 @@ #include "board.h" /* Key code for writing PRCR register. */ -#define BSP_PRV_PRCR_KEY (0xA500U) +#define BSP_PRV_PRCR_KEY (0xA500U) #define BSP_PRV_PRCR_PRC1_UNLOCK ((BSP_PRV_PRCR_KEY) | 0x2U) -#define BSP_PRV_PRCR_LOCK ((BSP_PRV_PRCR_KEY) | 0x0U) +#define BSP_PRV_PRCR_LOCK ((BSP_PRV_PRCR_KEY) | 0x0U) static const ioport_cfg_t family_pin_cfg = { .number_of_pins = sizeof(board_pin_cfg) / sizeof(ioport_pin_cfg_t), @@ -62,25 +62,38 @@ static ioport_instance_ctrl_t port_ctrl; // Vector Data //--------------------------------------------------------------------+ -BSP_DONT_REMOVE const fsp_vector_t g_vector_table[BSP_ICU_VECTOR_MAX_ENTRIES] BSP_PLACE_IN_SECTION(BSP_SECTION_APPLICATION_VECTORS) = { +BSP_DONT_REMOVE BSP_PLACE_IN_SECTION(BSP_SECTION_APPLICATION_VECTORS) +const fsp_vector_t g_vector_table[BSP_ICU_VECTOR_MAX_ENTRIES] = { [0] = usbfs_interrupt_handler, /* USBFS INT (USBFS interrupt) */ [1] = usbfs_resume_handler, /* USBFS RESUME (USBFS resume interrupt) */ [2] = usbfs_d0fifo_handler, /* USBFS FIFO 0 (DMA transfer request 0) */ [3] = usbfs_d1fifo_handler, /* USBFS FIFO 1 (DMA transfer request 1) */ + +#ifdef BOARD_HAS_USB_HIGHSPEED + [4] = usbhs_interrupt_handler, /* USBHS INT (USBHS interrupt) */ + [5] = usbhs_d0fifo_handler, /* USBHS FIFO 0 (DMA transfer request 0) */ + [6] = usbhs_d1fifo_handler, /* USBHS FIFO 1 (DMA transfer request 1) */ +#endif }; + const bsp_interrupt_event_t g_interrupt_event_link_select[BSP_ICU_VECTOR_MAX_ENTRIES] = { - [0] = BSP_PRV_IELS_ENUM(EVENT_USBFS_INT), /* USBFS INT (USBFS interrupt) */ - [1] = BSP_PRV_IELS_ENUM(EVENT_USBFS_RESUME), /* USBFS RESUME (USBFS resume interrupt) */ - [2] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_0), /* USBFS FIFO 0 (DMA transfer request 0) */ - [3] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_1) /* USBFS FIFO 1 (DMA transfer request 1) */ + [0] = BSP_PRV_IELS_ENUM(EVENT_USBFS_INT), /* USBFS INT (USBFS interrupt) */ + [1] = BSP_PRV_IELS_ENUM(EVENT_USBFS_RESUME), /* USBFS RESUME (USBFS resume interrupt) */ + [2] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_0), /* USBFS FIFO 0 (DMA transfer request 0) */ + [3] = BSP_PRV_IELS_ENUM(EVENT_USBFS_FIFO_1), /* USBFS FIFO 1 (DMA transfer request 1) */ + +#ifdef BOARD_HAS_USB_HIGHSPEED + [4] = BSP_PRV_IELS_ENUM(EVENT_USBHS_USB_INT_RESUME), /* USBHS USB INT RESUME (USBHS interrupt) */ + [5] = BSP_PRV_IELS_ENUM(EVENT_USBHS_FIFO_0), /* USBHS FIFO 0 (DMA transfer request 0) */ + [6] = BSP_PRV_IELS_ENUM(EVENT_USBHS_FIFO_1), /* USBHS FIFO 1 (DMA transfer request 1) */ +#endif }; //--------------------------------------------------------------------+ // Board porting API //--------------------------------------------------------------------+ -void board_init(void) -{ +void board_init(void) { /* Configure pins. */ R_IOPORT_Open(&port_ctrl, &family_pin_cfg); @@ -94,8 +107,8 @@ void board_init(void) // Enable USB module R_MSTP->MSTPCRB &= ~(1U << 11U); // FS -#ifdef R_USB_HS0_BASE -// R_MSTP->MSTPCRB &= ~(1U << 12U); // HS +#ifdef BOARD_HAS_USB_HIGHSPEED + R_MSTP->MSTPCRB &= ~(1U << 12U); #endif #if CFG_TUSB_OS == OPT_OS_FREERTOS @@ -145,66 +158,93 @@ void SysTick_Handler(void) { uint32_t board_millis(void) { return system_ticks; } + #endif //--------------------------------------------------------------------+ // Forward USB interrupt events to TinyUSB IRQ Handler //--------------------------------------------------------------------+ -void usbfs_interrupt_handler(void) -{ + +#if CFG_TUD_ENABLED && defined(BOARD_TUD_RHPORT) + #define PORT_SUPPORT_DEVICE(_n) (BOARD_TUD_RHPORT == _n) +#else + #define PORT_SUPPORT_DEVICE(_n) 0 +#endif + +#if CFG_TUH_ENABLED && defined(BOARD_TUH_RHPORT) + #define PORT_SUPPORT_HOST(_n) (BOARD_TUH_RHPORT == _n) +#else + #define PORT_SUPPORT_HOST(_n) 0 +#endif + +//------------- USB0 FullSpeed -------------// +void usbfs_interrupt_handler(void) { IRQn_Type irq = R_FSP_CurrentIrqGet(); R_BSP_IrqStatusClear(irq); -#if CFG_TUH_ENABLED + #if PORT_SUPPORT_HOST(0) tuh_int_handler(0); -#endif + #endif -#if CFG_TUD_ENABLED + #if PORT_SUPPORT_DEVICE(0) tud_int_handler(0); -#endif + #endif } -void usbfs_resume_handler(void) -{ +void usbfs_resume_handler(void) { IRQn_Type irq = R_FSP_CurrentIrqGet(); R_BSP_IrqStatusClear(irq); -#if CFG_TUH_ENABLED + #if PORT_SUPPORT_HOST(0) tuh_int_handler(0); -#endif + #endif -#if CFG_TUD_ENABLED + #if PORT_SUPPORT_DEVICE(0) tud_int_handler(0); -#endif + #endif } -void usbfs_d0fifo_handler(void) -{ +void usbfs_d0fifo_handler(void) { IRQn_Type irq = R_FSP_CurrentIrqGet(); R_BSP_IrqStatusClear(irq); + // TODO not used yet +} -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif +void usbfs_d1fifo_handler(void) { + IRQn_Type irq = R_FSP_CurrentIrqGet(); + R_BSP_IrqStatusClear(irq); + // TODO not used yet +} -#if CFG_TUD_ENABLED - tud_int_handler(0); -#endif +//------------- USB1 HighSpeed -------------// +#ifdef BOARD_HAS_USB_HIGHSPEED + +void usbhs_interrupt_handler(void) { + IRQn_Type irq = R_FSP_CurrentIrqGet(); + R_BSP_IrqStatusClear(irq); + + #if PORT_SUPPORT_HOST(1) + tuh_int_handler(1); + #endif + + #if PORT_SUPPORT_DEVICE(1) + tud_int_handler(1); + #endif } -void usbfs_d1fifo_handler(void) -{ +void usbhs_d0fifo_handler(void) { IRQn_Type irq = R_FSP_CurrentIrqGet(); R_BSP_IrqStatusClear(irq); + // TODO not used yet +} -#if CFG_TUH_ENABLED - tuh_int_handler(0); -#endif +void usbhs_d1fifo_handler(void) { + IRQn_Type irq = R_FSP_CurrentIrqGet(); + R_BSP_IrqStatusClear(irq); + // TODO not used yet +} -#if CFG_TUD_ENABLED - tud_int_handler(0); #endif -} //--------------------------------------------------------------------+ // stdlib diff --git a/hw/bsp/ra/vector_data.h b/hw/bsp/ra/vector_data.h index 3d8a24634..ca667faa3 100644 --- a/hw/bsp/ra/vector_data.h +++ b/hw/bsp/ra/vector_data.h @@ -6,22 +6,29 @@ extern "C" { #endif -#ifndef VECTOR_DATA_IRQ_COUNT - #define VECTOR_DATA_IRQ_COUNT 4 -#endif - /* ISR prototypes */ void usbfs_interrupt_handler(void); void usbfs_resume_handler(void); void usbfs_d0fifo_handler(void); void usbfs_d1fifo_handler(void); +#ifdef BOARD_HAS_USB_HIGHSPEED +void usbhs_interrupt_handler(void); +void usbhs_d0fifo_handler(void); +void usbhs_d1fifo_handler(void); +#endif + /* Vector table allocations */ #define USBFS_INT_IRQn 0 #define USBFS_RESUME_IRQn 1 #define USBFS_FIFO_0_IRQn 2 #define USBFS_FIFO_1_IRQn 3 +#define USBHS_USB_INT_RESUME_IRQn 4 /* USBHS USB INT RESUME (USBHS interrupt) */ +#define USBHS_FIFO_0_IRQn 5 /* USBHS FIFO 0 (DMA transfer request 0) */ +#define USBHS_FIFO_1_IRQn 6 /* USBHS FIFO 1 (DMA transfer request 1) */ + + #ifdef __cplusplus } #endif diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 9f3be78fd..496ebfc85 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -327,6 +327,7 @@ // Renesas //--------------------------------------------------------------------+ #elif TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N, OPT_MCU_RAXXX) + #define TUP_USBIP_RUSB2 #define TUP_DCD_ENDPOINT_MAX 10 //--------------------------------------------------------------------+ diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index e9ac46517..83d2a34c6 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -31,8 +31,7 @@ // We disable SOF for now until needed later on #define USE_SOF 0 -#if CFG_TUD_ENABLED && (TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) || \ - TU_CHECK_MCU(OPT_MCU_RAXXX)) +#if CFG_TUD_ENABLED && defined(TUP_USBIP_RUSB2) #include "device/dcd.h" #include "rusb2_type.h" -- cgit v1.3.1 From 4f4c93594d8f82c18f9a1052c4da2e7c31fc1b8c Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 5 Jul 2023 17:51:36 +0700 Subject: minor pipe clean up --- src/portable/renesas/rusb2/dcd_rusb2.c | 74 ++++++++++++++++++++-------------- 1 file changed, 43 insertions(+), 31 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 83d2a34c6..b58e0be01 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -93,20 +93,20 @@ typedef struct TU_ATTR_PACKED { typedef union TU_ATTR_PACKED { struct { - volatile uint16_t u8: 8; - volatile uint16_t : 0; + volatile uint8_t u8; + volatile uint8_t reserved8; }; volatile uint16_t u16; } hw_fifo_t; typedef union TU_ATTR_PACKED { struct { - volatile uint32_t : 24; - volatile uint32_t u8: 8; + volatile uint8_t reserved8[3]; + volatile uint8_t u8; }; struct { - volatile uint32_t : 16; - volatile uint32_t u16: 16; + volatile uint16_t reserved16; + volatile uint16_t u16; }; volatile uint32_t u32; } hw_fifo32_t; @@ -126,6 +126,19 @@ typedef struct TU_ATTR_PACKED TU_ATTR_PACKED_END // End of definition of packed structs (used by the CCRX toolchain) TU_ATTR_BIT_FIELD_ORDER_END +// Transfer conditions specifiable for each pipe: +// - Pipe 0: Control transfer with 64-byte single buffer +// - Pipes 1 and 2: Bulk isochronous transfer continuous transfer mode with programmable buffer size up +// to 2 KB and optional double buffer +// - Pipes 3 to 5: Bulk transfer continuous transfer mode with programmable buffer size up to 2 KB and +// optional double buffer +// - Pipes 6 to 9: Interrupt transfer with 64-byte single buffer +enum { + PIPE_1ST_BULK = 3, + PIPE_1ST_INTERRUPT = 6, + PIPE_COUNT = 10, +}; + typedef struct { pipe_state_t pipe[10]; @@ -137,34 +150,33 @@ typedef struct //--------------------------------------------------------------------+ static dcd_data_t _dcd; -#ifndef FIRST_BULK_PIPE -#define FIRST_BULK_PIPE 3 -#endif - static unsigned find_pipe(unsigned xfer) { switch (xfer) { - case TUSB_XFER_ISOCHRONOUS: - for (int i = 1; i <= 2; ++i) { - if (0 == _dcd.pipe[i].ep) return i; - } - break; - case TUSB_XFER_BULK: - for (int i = FIRST_BULK_PIPE; i <= 5; ++i) { - if (0 == _dcd.pipe[i].ep) return i; - } - for (int i = 1; i <= 1; ++i) { - if (0 == _dcd.pipe[i].ep) return i; - } - break; - case TUSB_XFER_INTERRUPT: - for (int i = 6; i <= 9; ++i) { - if (0 == _dcd.pipe[i].ep) return i; - } - break; - default: - /* No support for control transfer */ - break; + case TUSB_XFER_ISOCHRONOUS: + for (int i = 1; i < PIPE_1ST_BULK; ++i) { + if (0 == _dcd.pipe[i].ep) return i; + } + break; + + case TUSB_XFER_BULK: + for (int i = PIPE_1ST_BULK; i < PIPE_1ST_INTERRUPT; ++i) { + if (0 == _dcd.pipe[i].ep) return i; + } + for (int i = 1; i < PIPE_1ST_BULK; ++i) { + if (0 == _dcd.pipe[i].ep) return i; + } + break; + + case TUSB_XFER_INTERRUPT: + for (int i = PIPE_1ST_INTERRUPT; i < PIPE_COUNT; ++i) { + if (0 == _dcd.pipe[i].ep) return i; + } + break; + + default: + /* No support for control transfer */ + break; } return 0; } -- cgit v1.3.1 From f308435b649c37f0cffc1d5a566fb71c22b57aa1 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 5 Jul 2023 22:09:35 +0700 Subject: update ra type to include usbhs registers --- hw/bsp/ra/family.cmake | 1 - hw/bsp/ra/family.mk | 1 - src/portable/renesas/rusb2/rusb2_ra.c | 16 -- src/portable/renesas/rusb2/rusb2_ra.h | 83 +++++---- src/portable/renesas/rusb2/rusb2_type.h | 315 ++++++++++++++++++++------------ 5 files changed, 245 insertions(+), 171 deletions(-) delete mode 100644 src/portable/renesas/rusb2/rusb2_ra.c (limited to 'src/portable') diff --git a/hw/bsp/ra/family.cmake b/hw/bsp/ra/family.cmake index f4e978230..74329165f 100644 --- a/hw/bsp/ra/family.cmake +++ b/hw/bsp/ra/family.cmake @@ -120,7 +120,6 @@ function(family_configure_example TARGET RTOS) target_sources(${TARGET}-tinyusb PUBLIC ${TOP}/src/portable/renesas/rusb2/dcd_rusb2.c ${TOP}/src/portable/renesas/rusb2/hcd_rusb2.c - ${TOP}/src/portable/renesas/rusb2/rusb2_ra.c ) target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) diff --git a/hw/bsp/ra/family.mk b/hw/bsp/ra/family.mk index 9b6b02c02..b6e1bb0ae 100644 --- a/hw/bsp/ra/family.mk +++ b/hw/bsp/ra/family.mk @@ -18,7 +18,6 @@ CFLAGS += \ SRC_C += \ src/portable/renesas/rusb2/dcd_rusb2.c \ src/portable/renesas/rusb2/hcd_rusb2.c \ - src/portable/renesas/rusb2/rusb2_ra.c \ $(FSP_RA)/src/bsp/cmsis/Device/RENESAS/Source/startup.c \ $(FSP_RA)/src/bsp/cmsis/Device/RENESAS/Source/system.c \ $(FSP_RA)/src/bsp/mcu/all/bsp_clocks.c \ diff --git a/src/portable/renesas/rusb2/rusb2_ra.c b/src/portable/renesas/rusb2/rusb2_ra.c deleted file mode 100644 index ff2191b1f..000000000 --- a/src/portable/renesas/rusb2/rusb2_ra.c +++ /dev/null @@ -1,16 +0,0 @@ -#include "tusb_option.h" -#include "rusb2_ra.h" - -#if (CFG_TUSB_RHPORT0_MODE != 0) -IRQn_Type _usb_fs_irqn = USBFS_INT_IRQn; -void tud_set_irq_usbfs(IRQn_Type q) { - _usb_fs_irqn = q; -} -#endif - -#if (CFG_TUSB_RHPORT1_MODE != 0) -IRQn_Type _usb_hs_irqn = USBHS_USB_INT_RESUME_IRQn; -void tud_set_irq_usbhs(IRQn_Type q) { - _usb_hs_irqn = q; -} -#endif diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 07fcafe6f..ca7c38907 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -47,55 +47,53 @@ extern "C" { #pragma GCC diagnostic pop #endif -extern IRQn_Type _usb_fs_irqn; -extern IRQn_Type _usb_hs_irqn; +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ -#if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE) -// fallback -#define CFG_TUSB_RHPORT0_MODE ( CFG_TUD_ENABLED ? OPT_MODE_DEVICE : OPT_MODE_HOST ) -#define CFG_TUSB_RHPORT1_MODE 0 +// IAR does not have __builtin_ctz +#if defined(__ICCARM__) + #define __builtin_ctz(x) __iar_builtin_CLZ(__iar_builtin_RBIT(x)) #endif -#if defined(__ICCARM__) - #define __builtin_ctz(x) __iar_builtin_CLZ(__iar_builtin_RBIT(x)) +typedef struct { + uint32_t reg_base; + int32_t irqnum; +}rusb2_controller_t; + +#if defined(BSP_MCU_GROUP_RA6M5) || defined(BSP_MCU_GROUP_RA6M3) || (BSP_CFG_MCU_PART_SERIES == 8) + #define RUSB2_HAS_HIGHSPEED + #define RUSB2_CONTROLLER_COUNT 2 +#else + #define RUSB2_CONTROLLER_COUNT 1 #endif +// USBFS_INT_IRQn and USBHS_USB_INT_RESUME_IRQn are generated by FSP +static rusb2_controller_t rusb2_controller[] = { + { .reg_base = R_USB_FS0_BASE, .irqnum = USBFS_INT_IRQn }, + #ifdef RUSB2_HAS_HIGHSPEED + { .reg_base = R_USB_HS0_BASE, .irqnum = USBHS_USB_INT_RESUME_IRQn }, + #endif +}; + TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_enable(uint8_t rhport) { -#ifdef CFG_TUSB_RHPORT1_MODE -#if (CFG_TUSB_RHPORT1_MODE != 0) - if (rhport == 1) { - NVIC_EnableIRQ(_usb_hs_irqn); - } -#endif -#endif - -#ifdef CFG_TUSB_RHPORT0_MODE -#if (CFG_TUSB_RHPORT0_MODE != 0) - if (rhport == 0) { - NVIC_EnableIRQ(_usb_fs_irqn); - } -#endif -#endif + #if RUSB2_CONTROLLER_COUNT > 1 + NVIC_EnableIRQ(rusb2_controller[rhport].irqnum); + #else + (void) rhport; + NVIC_EnableIRQ(rusb2_controller[0].irqnum); + #endif } TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_disable(uint8_t rhport) { -#ifdef CFG_TUSB_RHPORT1_MODE -#if (CFG_TUSB_RHPORT1_MODE != 0) - if (rhport == 1) { - NVIC_DisableIRQ(_usb_hs_irqn); - } -#endif -#endif - -#ifdef CFG_TUSB_RHPORT0_MODE -#if (CFG_TUSB_RHPORT0_MODE != 0) - if (rhport == 0) { - NVIC_DisableIRQ(_usb_fs_irqn); - } -#endif -#endif + #if RUSB2_CONTROLLER_COUNT > 1 + NVIC_DisableIRQ(rusb2_controller[rhport].irqnum); + #else + (void) rhport; + NVIC_DisableIRQ(rusb2_controller[0].irqnum); + #endif } // MCU specific PHY init @@ -103,6 +101,15 @@ TU_ATTR_ALWAYS_INLINE static inline void rusb2_phy_init(void) { } +void tud_int_set_irqnum(uint8_t rhport, int32_t irqnum) { + #if RUSB2_CONTROLLER_COUNT > 1 + rusb2_controller[rhport].irqnum = irqnum; + #else + (void) rhport; + rusb2_controller[0].irqnum = irqnum; + #endif +} + #ifdef __cplusplus } #endif diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index 90ba4f012..0928f5aeb 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -46,10 +46,10 @@ typedef struct { volatile uint16_t E; /* (@ 0x00000000) Pipe Transaction Counter Enable Register */ struct TU_ATTR_PACKED { - uint16_t : 8; + uint16_t : 8; volatile uint16_t TRCLR : 1; /* [8..8] Transaction Counter Clear */ volatile uint16_t TRENB : 1; /* [9..9] Transaction Counter Enable */ - uint16_t : 6; + uint16_t : 6; } E_b; }; @@ -62,7 +62,8 @@ typedef struct { }; } RUSB2_PIPE_TR_t; /* Size = 4 (0x4) */ -/* LINK_REG Structure */ + +/* RUSB2 Registers Structure */ typedef struct { union { volatile uint16_t SYSCFG; /* (@ 0x00000000) System Configuration Control Register */ @@ -74,7 +75,7 @@ typedef struct { volatile uint16_t DPRPU : 1; /* [4..4] D+ Line Resistor Control */ volatile uint16_t DRPD : 1; /* [5..5] D+/D- Line Resistor Control */ volatile uint16_t DCFM : 1; /* [6..6] Controller Function Select */ - uint16_t : 1; + volatile uint16_t HSE : 1; // [7..7] High-Speed Operation Enable volatile uint16_t CNEN : 1; /* [8..8] CNEN Single End Receiver Enable */ uint16_t : 1; volatile uint16_t SCKE : 1; /* [10..10] USB Clock Enable */ @@ -87,7 +88,7 @@ typedef struct { struct TU_ATTR_PACKED { volatile uint16_t BWAIT : 4; /* [3..0] CPU Bus Access Wait Specification BWAIT waits (BWAIT+2 access cycles) */ - uint16_t : 12; + uint16_t : 12; } BUSWAIT_b; }; @@ -98,8 +99,7 @@ typedef struct { volatile const uint16_t LNST : 2; /* [1..0] USB Data Line Status Monitor */ volatile const uint16_t IDMON : 1; /* [2..2] External ID0 Input Pin Monitor */ uint16_t : 2; - volatile const uint16_t - SOFEA : 1; /* [5..5] SOF Active Monitor While Host Controller Function is Selected. */ + volatile const uint16_t SOFEA : 1; /* [5..5] SOF Active Monitor While Host Controller Function is Selected. */ volatile const uint16_t HTACT : 1; /* [6..6] USB Host Sequencer Status Monitor */ uint16_t : 7; volatile const uint16_t OVCMON : 2; /* [15..14] External USB0_OVRCURA/ USB0_OVRCURB Input Pin Monitor */ @@ -111,7 +111,7 @@ typedef struct { struct TU_ATTR_PACKED { volatile const uint16_t PLLLOCK : 1; /* [0..0] PLL Lock Flag */ - uint16_t : 15; + uint16_t : 15; } PLLSTA_b; }; @@ -139,7 +139,7 @@ typedef struct { struct TU_ATTR_PACKED { volatile uint16_t UTST : 4; /* [3..0] Test Mode */ - uint16_t : 12; + uint16_t : 12; } TESTMODE_b; }; volatile const uint16_t RESERVED1; @@ -295,7 +295,7 @@ typedef struct { volatile uint16_t INTENB0; /* (@ 0x00000030) Interrupt Enable Register 0 */ struct TU_ATTR_PACKED { - uint16_t : 8; + uint16_t : 8; volatile uint16_t BRDYE : 1; /* [8..8] Buffer Ready Interrupt Enable */ volatile uint16_t NRDYE : 1; /* [9..9] Buffer Not Ready Response Interrupt Enable */ volatile uint16_t BEMPE : 1; /* [10..10] Buffer Empty Interrupt Enable */ @@ -316,7 +316,10 @@ typedef struct { volatile uint16_t SACKE : 1; /* [4..4] Setup Transaction Normal Response Interrupt Enable */ volatile uint16_t SIGNE : 1; /* [5..5] Setup Transaction Error Interrupt Enable */ volatile uint16_t EOFERRE : 1; /* [6..6] EOF Error Detection Interrupt Enable */ - uint16_t : 4; + uint16_t : 1; + volatile uint16_t LPMENDE : 1; /*!< [8..8] LPM Transaction End Interrupt Enable */ + volatile uint16_t L1RSMENDE : 1; /*!< [9..9] L1 Resume End Interrupt Enable */ + uint16_t : 1; volatile uint16_t ATTCHE : 1; /* [11..11] Connection Detection Interrupt Enable */ volatile uint16_t DTCHE : 1; /* [12..12] Disconnection Detection Interrupt Enable */ uint16_t : 1; @@ -340,7 +343,7 @@ typedef struct { volatile uint16_t PIPE7BRDYE : 1; /* [7..7] BRDY Interrupt Enable for PIPE */ volatile uint16_t PIPE8BRDYE : 1; /* [8..8] BRDY Interrupt Enable for PIPE */ volatile uint16_t PIPE9BRDYE : 1; /* [9..9] BRDY Interrupt Enable for PIPE */ - uint16_t : 6; + uint16_t : 6; } BRDYENB_b; }; @@ -358,7 +361,7 @@ typedef struct { volatile uint16_t PIPE7NRDYE : 1; /* [7..7] NRDY Interrupt Enable for PIPE */ volatile uint16_t PIPE8NRDYE : 1; /* [8..8] NRDY Interrupt Enable for PIPE */ volatile uint16_t PIPE9NRDYE : 1; /* [9..9] NRDY Interrupt Enable for PIPE */ - uint16_t : 6; + uint16_t : 6; } NRDYENB_b; }; @@ -376,7 +379,7 @@ typedef struct { volatile uint16_t PIPE7BEMPE : 1; /* [7..7] BEMP Interrupt Enable for PIPE */ volatile uint16_t PIPE8BEMPE : 1; /* [8..8] BEMP Interrupt Enable for PIPE */ volatile uint16_t PIPE9BEMPE : 1; /* [9..9] BEMP Interrupt Enable for PIPE */ - uint16_t : 6; + uint16_t : 6; } BEMPENB_b; }; @@ -390,7 +393,7 @@ typedef struct { volatile uint16_t BRDYM : 1; /* [6..6] BRDY Interrupt Status Clear Timing */ uint16_t : 1; volatile uint16_t TRNENSEL : 1; /* [8..8] Transaction-Enabled Time Select */ - uint16_t : 7; + uint16_t : 7; } SOFCFG_b; }; @@ -467,7 +470,7 @@ typedef struct { volatile uint16_t PIPE7BRDY : 1; /* [7..7] BRDY Interrupt Status for PIPE */ volatile uint16_t PIPE8BRDY : 1; /* [8..8] BRDY Interrupt Status for PIPE */ volatile uint16_t PIPE9BRDY : 1; /* [9..9] BRDY Interrupt Status for PIPE */ - uint16_t : 6; + uint16_t : 6; } BRDYSTS_b; }; @@ -485,7 +488,7 @@ typedef struct { volatile uint16_t PIPE7NRDY : 1; /* [7..7] NRDY Interrupt Status for PIPE */ volatile uint16_t PIPE8NRDY : 1; /* [8..8] NRDY Interrupt Status for PIPE */ volatile uint16_t PIPE9NRDY : 1; /* [9..9] NRDY Interrupt Status for PIPE */ - uint16_t : 6; + uint16_t : 6; } NRDYSTS_b; }; @@ -503,7 +506,7 @@ typedef struct { volatile uint16_t PIPE7BEMP : 1; /* [7..7] BEMP Interrupt Status for PIPE */ volatile uint16_t PIPE8BEMP : 1; /* [8..8] BEMP Interrupt Status for PIPE */ volatile uint16_t PIPE9BEMP : 1; /* [9..9] BEMP Interrupt Status for PIPE */ - uint16_t : 6; + uint16_t : 6; } BEMPSTS_b; }; @@ -609,7 +612,8 @@ typedef struct { volatile uint16_t SQCLR : 1; /* [8..8] Sequence Toggle Bit Clear */ uint16_t : 2; volatile uint16_t SUREQCLR : 1; /* [11..11] SUREQ Bit Clear */ - uint16_t : 2; + volatile uint16_t CSSTS : 1; /* [12..12] Split Transaction COMPLETE SPLIT(CSPLIT) Status */ + volatile uint16_t CSCLR : 1; /* [13..13] Split Transaction CSPLIT Status Clear */ volatile uint16_t SUREQ : 1; /* [14..14] Setup Token Transmission */ volatile const uint16_t BSTS : 1; /* [15..15] Buffer Status */ } DCPCTR_b; @@ -621,7 +625,7 @@ typedef struct { struct TU_ATTR_PACKED { volatile uint16_t PIPESEL : 4; /* [3..0] Pipe Window Select */ - uint16_t : 12; + uint16_t : 12; } PIPESEL_b; }; volatile const uint16_t RESERVED11; @@ -634,21 +638,31 @@ typedef struct { volatile uint16_t DIR : 1; /* [4..4] Transfer Direction */ uint16_t : 2; volatile uint16_t SHTNAK : 1; /* [7..7] Pipe Disabled at End of Transfer */ - uint16_t : 1; + volatile uint16_t CNTMD : 1; /* [8..8] Continuous Transfer Mode */ volatile uint16_t DBLB : 1; /* [9..9] Double Buffer Mode */ volatile uint16_t BFRE : 1; /* [10..10] BRDY Interrupt Operation Specification */ uint16_t : 3; volatile uint16_t TYPE : 2; /* [15..14] Transfer Type */ } PIPECFG_b; }; - volatile const uint16_t RESERVED12; + + union { + volatile uint16_t PIPEBUF; /*!< (@ 0x0000006A) Pipe Buffer Register */ + + struct { + volatile uint16_t BUFNMB : 8; // [7..0] Buffer NumberThese bits specify the FIFO buffer number of the selected pipe (04h to 87h) + uint16_t : 2; + volatile uint16_t BUFSIZE : 5; /*!< [14..10] Buffer Size 00h: 64 bytes 01h: 128 bytes : 1Fh: 2 Kbytes */ + uint16_t : 1; + } PIPEBUF_b; + }; union { volatile uint16_t PIPEMAXP; /* (@ 0x0000006C) Pipe Maximum Packet Size Register */ struct TU_ATTR_PACKED { - volatile uint16_t MXPS : 9; /* [8..0] Maximum Packet Size */ - uint16_t : 3; + volatile uint16_t MXPS : 11; /* [10..0] Maximum Packet Size */ + uint16_t : 1; volatile uint16_t DEVSEL : 4; /* [15..12] Device Select */ } PIPEMAXP_b; }; @@ -694,11 +708,9 @@ typedef struct { struct TU_ATTR_PACKED { volatile uint16_t RPDME0 : 1; /* [0..0] D- Pin Pull-Down Control */ volatile uint16_t IDPSRCE0 : 1; /* [1..1] D+ Pin IDPSRC Output Control */ - volatile uint16_t - IDMSINKE0 : 1; /* [2..2] D- Pin 0.6 V Input Detection (Comparator and Sink) Control */ + volatile uint16_t IDMSINKE0 : 1; /* [2..2] D- Pin 0.6 V Input Detection (Comparator and Sink) Control */ volatile uint16_t VDPSRCE0 : 1; /* [3..3] D+ Pin VDPSRC (0.6 V) Output Control */ - volatile uint16_t - IDPSINKE0 : 1; /* [4..4] D+ Pin 0.6 V Input Detection (Comparator and Sink) Control */ + volatile uint16_t IDPSINKE0 : 1; /* [4..4] D+ Pin 0.6 V Input Detection (Comparator and Sink) Control */ volatile uint16_t VDMSRCE0 : 1; /* [5..5] D- Pin VDMSRC (0.6 V) Output Control */ uint16_t : 1; volatile uint16_t BATCHGE0 : 1; /* [7..7] BC (Battery Charger) Function Ch0 General Enable Control */ @@ -715,7 +727,7 @@ typedef struct { struct TU_ATTR_PACKED { volatile uint16_t UCKSELC : 1; /* [0..0] USB Clock Selection */ - uint16_t : 15; + uint16_t : 15; } UCKSEL_b; }; volatile const uint16_t RESERVED18; @@ -737,11 +749,11 @@ typedef struct { volatile uint16_t DEVADD[10]; /* (@ 0x000000D0) Device Address Configuration Register */ struct TU_ATTR_PACKED { - uint16_t : 6; + uint16_t : 6; volatile uint16_t USBSPD : 2; /* [7..6] Transfer Speed of Communication Target Device */ volatile uint16_t HUBPORT : 3; /* [10..8] Communication Target Connecting Hub Port */ volatile uint16_t UPPHUB : 4; /* [14..11] Communication Target Connecting Hub Register */ - uint16_t : 1; + uint16_t : 1; } DEVADD_b[10]; }; volatile const uint32_t RESERVED21[3]; @@ -754,7 +766,7 @@ typedef struct { volatile uint32_t SLEWR01 : 1; /* [1..1] Receiver Cross Point Adjustment 01 */ volatile uint32_t SLEWF00 : 1; /* [2..2] Receiver Cross Point Adjustment 00 */ volatile uint32_t SLEWF01 : 1; /* [3..3] Receiver Cross Point Adjustment 01 */ - uint32_t : 28; + uint32_t : 28; } PHYSLEW_b; }; volatile const uint32_t RESERVED22[3]; @@ -763,9 +775,9 @@ typedef struct { volatile uint16_t LPCTRL; /* (@ 0x00000100) Low Power Control Register */ struct TU_ATTR_PACKED { - uint16_t : 7; + uint16_t : 7; volatile uint16_t HWUPM : 1; /* [7..7] Resume Return Mode Setting */ - uint16_t : 8; + uint16_t : 8; } LPCTRL_b; }; @@ -773,9 +785,9 @@ typedef struct { volatile uint16_t LPSTS; /* (@ 0x00000102) Low Power Status Register */ struct TU_ATTR_PACKED { - uint16_t : 14; + uint16_t : 14; volatile uint16_t SUSPENDM : 1; /* [14..14] UTMI SuspendM Control */ - uint16_t : 1; + uint16_t : 1; } LPSTS_b; }; volatile const uint32_t RESERVED23[15]; @@ -793,7 +805,7 @@ typedef struct { uint16_t : 2; volatile const uint16_t CHGDETSTS : 1; /* [8..8] CHGDET Status */ volatile const uint16_t PDDETSTS : 1; /* [9..9] PDDET Status */ - uint16_t : 6; + uint16_t : 6; } BCCTRL_b; }; volatile const uint16_t RESERVED24; @@ -809,7 +821,7 @@ typedef struct { volatile uint16_t HIRDTHR : 4; /* [11..8] L1 Response Negotiation Threshold Value */ uint16_t : 2; volatile uint16_t L1EXTMD : 1; /* [14..14] PHY Control Mode at L1 Return */ - uint16_t : 1; + uint16_t : 1; } PL1CTRL1_b; }; @@ -817,10 +829,10 @@ typedef struct { volatile uint16_t PL1CTRL2; /* (@ 0x00000146) Function L1 Control Register 2 */ struct TU_ATTR_PACKED { - uint16_t : 8; + uint16_t : 8; volatile uint16_t HIRDMON : 4; /* [11..8] HIRD Value Monitor */ volatile uint16_t RWEMON : 1; /* [12..12] RWE Value Monitor */ - uint16_t : 3; + uint16_t : 3; } PL1CTRL2_b; }; @@ -830,7 +842,7 @@ typedef struct { struct TU_ATTR_PACKED { volatile uint16_t L1REQ : 1; /* [0..0] L1 Transition Request */ volatile const uint16_t L1STATUS : 2; /* [2..1] L1 Request Completion Status */ - uint16_t : 13; + uint16_t : 13; } HL1CTRL1_b; }; @@ -846,18 +858,48 @@ typedef struct { volatile uint16_t BESL : 1; /* [15..15] BESL & Alternate HIRD */ } HL1CTRL2_b; }; - volatile const uint32_t RESERVED25[5]; + + volatile uint32_t RESERVED25_1; + + union { + volatile uint16_t PHYTRIM1; /*!< (@ 0x00000150) PHY Timing Register 1 */ + + struct { + volatile uint16_t DRISE : 2; /*!< [1..0] FS/LS Rising-Edge Output Waveform Adjustment Function */ + volatile uint16_t DFALL : 2; /*!< [3..2] FS/LS Falling-Edge Output Waveform Adjustment Function */ + uint16_t : 3; + volatile uint16_t PCOMPENB : 1; /*!< [7..7] PVDD Start-up Detection */ + volatile uint16_t HSIUP : 4; /*!< [11..8] HS Output Level Setting */ + volatile uint16_t IMPOFFSET : 3; /*!< [14..12] terminating resistance offset value setting.Offset value for adjusting the terminating resistance. */ + uint16_t : 1; + } PHYTRIM1_b; + }; + + union { + volatile uint16_t PHYTRIM2; /*!< (@ 0x00000152) PHY Timing Register 2 */ + + struct { + volatile uint16_t SQU : 4; /*!< [3..0] Squelch Detection Level */ + uint16_t : 3; + volatile uint16_t HSRXENMO : 1; /*!< [7..7] HS Receive Enable Control Mode */ + volatile uint16_t PDR : 2; /*!< [9..8] HS Output Adjustment Function */ + uint16_t : 2; + volatile uint16_t DIS : 3; /*!< [14..12] Disconnect Detection Level */ + uint16_t : 1; + } PHYTRIM2_b; + }; + volatile uint32_t RESERVED25_2[3]; union { volatile const uint32_t DPUSR0R; /* (@ 0x00000160) Deep Standby USB Transceiver Control/Pin Monitor Register */ struct TU_ATTR_PACKED { - uint32_t : 20; + uint32_t : 20; volatile const uint32_t DOVCAHM : 1; /* [20..20] OVRCURA InputIndicates OVRCURA input signal on the HS side of USB port. */ volatile const uint32_t DOVCBHM : 1; /* [21..21] OVRCURB InputIndicates OVRCURB input signal on the HS side of USB port. */ uint32_t : 1; volatile const uint32_t DVBSTSHM : 1; /* [23..23] VBUS InputIndicates VBUS input signal on the HS side of USB port. */ - uint32_t : 8; + uint32_t : 8; } DPUSR0R_b; }; @@ -865,7 +907,7 @@ typedef struct { volatile uint32_t DPUSR1R; /* (@ 0x00000164) Deep Standby USB Suspend/Resume Interrupt Register */ struct TU_ATTR_PACKED { - uint32_t : 4; + uint32_t : 4; volatile uint32_t DOVCAHE : 1; /* [4..4] OVRCURA Interrupt Enable Clear */ volatile uint32_t DOVCBHE : 1; /* [5..5] OVRCURB Interrupt Enable Clear */ uint32_t : 1; @@ -875,7 +917,7 @@ typedef struct { volatile const uint32_t DOVCBH : 1; /* [21..21] Indication of Return from OVRCURB Interrupt Source */ uint32_t : 1; volatile const uint32_t DVBSTSH : 1; /* [23..23] Indication of Return from VBUS Interrupt Source */ - uint32_t : 8; + uint32_t : 8; } DPUSR1R_b; }; @@ -891,7 +933,7 @@ typedef struct { uint16_t : 2; volatile uint16_t DPINTE : 1; /* [8..8] DP Interrupt Enable Clear */ volatile uint16_t DMINTE : 1; /* [9..9] DM Interrupt Enable Clear */ - uint16_t : 6; + uint16_t : 6; } DPUSR2R_b; }; @@ -901,7 +943,7 @@ typedef struct { struct TU_ATTR_PACKED { volatile uint16_t FIXPHY : 1; /* [0..0] USB Transceiver Control Fix */ volatile uint16_t FIXPHYPD : 1; /* [1..1] USB Transceiver Control Fix for PLL */ - uint16_t : 14; + uint16_t : 14; } DPUSRCR_b; }; volatile const uint32_t RESERVED26[165]; @@ -924,7 +966,7 @@ typedef struct { volatile const uint32_t DOVCB0 : 1; /* [21..21] USB OVRCURB InputIndicates the OVRCURB input signal of the USB. */ uint32_t : 1; volatile const uint32_t DVBSTS0 : 1; /* [23..23] USB VBUS InputIndicates the VBUS input signal of the USB. */ - uint32_t : 8; + uint32_t : 8; } DPUSR0R_FS_b; }; @@ -947,10 +989,10 @@ typedef struct { volatile const uint32_t DOVRCRB0 : 1; /* [21..21] USB OVRCURB Interrupt Source Recovery */ uint32_t : 1; volatile const uint32_t DVBINT0 : 1; /* [23..23] USB VBUS Interrupt Source Recovery */ - uint32_t : 8; + uint32_t : 8; } DPUSR1R_FS_b; }; -} RUSB2_REG_t; /* Size = 1032 (0x408) */ +} rusb2_reg_t; /* Size = 1032 (0x408) */ TU_ATTR_PACKED_END /* End of definition of packed structs (used by the CCRX toolchain) */ TU_ATTR_BIT_FIELD_ORDER_END @@ -970,13 +1012,15 @@ TU_ATTR_BIT_FIELD_ORDER_END #define RUSB2_PIPE_TR_N_TRNCNT_Pos (0UL) /* TRNCNT (Bit 0) */ #define RUSB2_PIPE_TR_N_TRNCNT_Msk (0xffffUL) /* TRNCNT (Bitfield-Mask: 0xffff) */ -// LINK_REG +// Core Registers // SYSCFG #define RUSB2_SYSCFG_SCKE_Pos (10UL) /* SCKE (Bit 10) */ #define RUSB2_SYSCFG_SCKE_Msk (0x400UL) /* SCKE (Bitfield-Mask: 0x01) */ #define RUSB2_SYSCFG_CNEN_Pos (8UL) /* CNEN (Bit 8) */ #define RUSB2_SYSCFG_CNEN_Msk (0x100UL) /* CNEN (Bitfield-Mask: 0x01) */ +#define RUSB2_SYSCFG_HSE_Pos (7UL) /*!< HSE (Bit 7) */ +#define RUSB2_SYSCFG_HSE_Msk (0x80UL) /*!< HSE (Bitfield-Mask: 0x01) */ #define RUSB2_SYSCFG_DCFM_Pos (6UL) /* DCFM (Bit 6) */ #define RUSB2_SYSCFG_DCFM_Msk (0x40UL) /* DCFM (Bitfield-Mask: 0x01) */ #define RUSB2_SYSCFG_DRPD_Pos (5UL) /* DRPD (Bit 5) */ @@ -1135,6 +1179,10 @@ TU_ATTR_BIT_FIELD_ORDER_END #define RUSB2_INTENB1_DTCHE_Msk (0x1000UL) /* DTCHE (Bitfield-Mask: 0x01) */ #define RUSB2_INTENB1_ATTCHE_Pos (11UL) /* ATTCHE (Bit 11) */ #define RUSB2_INTENB1_ATTCHE_Msk (0x800UL) /* ATTCHE (Bitfield-Mask: 0x01) */ +#define RUSB2_INTENB1_L1RSMENDE_Pos (9UL) /*!< L1RSMENDE (Bit 9) */ +#define RUSB2_INTENB1_L1RSMENDE_Msk (0x200UL) /*!< L1RSMENDE (Bitfield-Mask: 0x01) */ +#define RUSB2_INTENB1_LPMENDE_Pos (8UL) /*!< LPMENDE (Bit 8) */ +#define RUSB2_INTENB1_LPMENDE_Msk (0x100UL) /*!< LPMENDE (Bitfield-Mask: 0x01) */ #define RUSB2_INTENB1_EOFERRE_Pos (6UL) /* EOFERRE (Bit 6) */ #define RUSB2_INTENB1_EOFERRE_Msk (0x40UL) /* EOFERRE (Bitfield-Mask: 0x01) */ #define RUSB2_INTENB1_SIGNE_Pos (5UL) /* SIGNE (Bit 5) */ @@ -1299,6 +1347,10 @@ TU_ATTR_BIT_FIELD_ORDER_END #define RUSB2_DCPCTR_BSTS_Msk (0x8000UL) /* BSTS (Bitfield-Mask: 0x01) */ #define RUSB2_DCPCTR_SUREQ_Pos (14UL) /* SUREQ (Bit 14) */ #define RUSB2_DCPCTR_SUREQ_Msk (0x4000UL) /* SUREQ (Bitfield-Mask: 0x01) */ +#define R_USB_HS0_DCPCTR_CSCLR_Pos (13UL) /*!< CSCLR (Bit 13) */ +#define RUSB2_DCPCTR_CSCLR_Msk (0x2000UL) /*!< CSCLR (Bitfield-Mask: 0x01) */ +#define RUSB2_DCPCTR_CSSTS_Pos (12UL) /*!< CSSTS (Bit 12) */ +#define RUSB2_DCPCTR_CSSTS_Msk (0x1000UL) /*!< CSSTS (Bitfield-Mask: 0x01) */ #define RUSB2_DCPCTR_SUREQCLR_Pos (11UL) /* SUREQCLR (Bit 11) */ #define RUSB2_DCPCTR_SUREQCLR_Msk (0x800UL) /* SUREQCLR (Bitfield-Mask: 0x01) */ #define RUSB2_DCPCTR_SQCLR_Pos (8UL) /* SQCLR (Bit 8) */ @@ -1325,6 +1377,8 @@ TU_ATTR_BIT_FIELD_ORDER_END #define RUSB2_PIPECFG_BFRE_Msk (0x400UL) /* BFRE (Bitfield-Mask: 0x01) */ #define RUSB2_PIPECFG_DBLB_Pos (9UL) /* DBLB (Bit 9) */ #define RUSB2_PIPECFG_DBLB_Msk (0x200UL) /* DBLB (Bitfield-Mask: 0x01) */ +#define RUSB2_PIPECFG_CNTMD_Pos (8UL) /*!< CNTMD (Bit 8) */ +#define RUSB2_PIPECFG_CNTMD_Msk (0x100UL) /*!< CNTMD (Bitfield-Mask: 0x01) */ #define RUSB2_PIPECFG_SHTNAK_Pos (7UL) /* SHTNAK (Bit 7) */ #define RUSB2_PIPECFG_SHTNAK_Msk (0x80UL) /* SHTNAK (Bitfield-Mask: 0x01) */ #define RUSB2_PIPECFG_DIR_Pos (4UL) /* DIR (Bit 4) */ @@ -1332,6 +1386,12 @@ TU_ATTR_BIT_FIELD_ORDER_END #define RUSB2_PIPECFG_EPNUM_Pos (0UL) /* EPNUM (Bit 0) */ #define RUSB2_PIPECFG_EPNUM_Msk (0xfUL) /* EPNUM (Bitfield-Mask: 0x0f) */ +// PIPEBUF +#define RUSB2_PIPEBUF_BUFSIZE_Pos (10UL) /*!< BUFSIZE (Bit 10) */ +#define RUSB2_PIPEBUF_BUFSIZE_Msk (0x7c00UL) /*!< BUFSIZE (Bitfield-Mask: 0x1f) */ +#define RUSB2_PIPEBUF_BUFNMB_Pos (0UL) /*!< BUFNMB (Bit 0) */ +#define RUSB2_PIPEBUF_BUFNMB_Msk (0xffUL) /*!< BUFNMB (Bitfield-Mask: 0xff) */ + // PIPEMAXP #define RUSB2_PIPEMAXP_DEVSEL_Pos (12UL) /* DEVSEL (Bit 12) */ #define RUSB2_PIPEMAXP_DEVSEL_Msk (0xf000UL) /* DEVSEL (Bitfield-Mask: 0x0f) */ @@ -1478,6 +1538,28 @@ TU_ATTR_BIT_FIELD_ORDER_END #define RUSB2_HL1CTRL2_L1ADDR_Pos (0UL) /* L1ADDR (Bit 0) */ #define RUSB2_HL1CTRL2_L1ADDR_Msk (0xfUL) /* L1ADDR (Bitfield-Mask: 0x0f) */ +// PHYTRIM1 +#define RUSB2_PHYTRIM1_IMPOFFSET_Pos (12UL) /*!< IMPOFFSET (Bit 12) */ +#define RUSB2_PHYTRIM1_IMPOFFSET_Msk (0x7000UL) /*!< IMPOFFSET (Bitfield-Mask: 0x07) */ +#define RUSB2_PHYTRIM1_HSIUP_Pos (8UL) /*!< HSIUP (Bit 8) */ +#define RUSB2_PHYTRIM1_HSIUP_Msk (0xf00UL) /*!< HSIUP (Bitfield-Mask: 0x0f) */ +#define RUSB2_PHYTRIM1_PCOMPENB_Pos (7UL) /*!< PCOMPENB (Bit 7) */ +#define RUSB2_PHYTRIM1_PCOMPENB_Msk (0x80UL) /*!< PCOMPENB (Bitfield-Mask: 0x01) */ +#define RUSB2_PHYTRIM1_DFALL_Pos (2UL) /*!< DFALL (Bit 2) */ +#define RUSB2_PHYTRIM1_DFALL_Msk (0xcUL) /*!< DFALL (Bitfield-Mask: 0x03) */ +#define RUSB2_PHYTRIM1_DRISE_Pos (0UL) /*!< DRISE (Bit 0) */ +#define RUSB2_PHYTRIM1_DRISE_Msk (0x3UL) /*!< DRISE (Bitfield-Mask: 0x03) */ + +// PHYTRIM2 +#define RUSB2_PHYTRIM2_DIS_Pos (12UL) /*!< DIS (Bit 12) */ +#define RUSB2_PHYTRIM2_DIS_Msk (0x7000UL) /*!< DIS (Bitfield-Mask: 0x07) */ +#define RUSB2_PHYTRIM2_PDR_Pos (8UL) /*!< PDR (Bit 8) */ +#define RUSB2_PHYTRIM2_PDR_Msk (0x300UL) /*!< PDR (Bitfield-Mask: 0x03) */ +#define RUSB2_PHYTRIM2_HSRXENMO_Pos (7UL) /*!< HSRXENMO (Bit 7) */ +#define RUSB2_PHYTRIM2_HSRXENMO_Msk (0x80UL) /*!< HSRXENMO (Bitfield-Mask: 0x01) */ +#define RUSB2_PHYTRIM2_SQU_Pos (0UL) /*!< SQU (Bit 0) */ +#define RUSB2_PHYTRIM2_SQU_Msk (0xfUL) /*!< SQU (Bitfield-Mask: 0x0f) */ + // DPUSR0R #define RUSB2_DPUSR0R_DVBSTSHM_Pos (23UL) /* DVBSTSHM (Bit 23) */ #define RUSB2_DPUSR0R_DVBSTSHM_Msk (0x800000UL) /* DVBSTSHM (Bitfield-Mask: 0x01) */ @@ -1599,69 +1681,72 @@ TU_ATTR_BIT_FIELD_ORDER_END //--------------------------------------------------------------------+ TU_VERIFY_STATIC(sizeof(RUSB2_PIPE_TR_t) == 4, "incorrect size"); -TU_VERIFY_STATIC(sizeof(RUSB2_REG_t) == 1032, "incorrect size"); - -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, SYSCFG ) == 0x00000000, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, BUSWAIT ) == 0x00000002, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, SYSSTS0 ) == 0x00000004, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PLLSTA ) == 0x00000006, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DVSTCTR0 ) == 0x00000008, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, TESTMODE ) == 0x0000000C, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, CFIFO ) == 0x00000014, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, D0FIFO ) == 0x00000018, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, D1FIFO ) == 0x0000001C, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, CFIFOSEL ) == 0x00000020, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, CFIFOCTR ) == 0x00000022, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, D0FIFOSEL ) == 0x00000028, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, D0FIFOCTR ) == 0x0000002A, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, D1FIFOSEL ) == 0x0000002C, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, D1FIFOCTR ) == 0x0000002E, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, INTENB0 ) == 0x00000030, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, INTENB1 ) == 0x00000032, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, BRDYENB ) == 0x00000036, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, NRDYENB ) == 0x00000038, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, BEMPENB ) == 0x0000003A, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, SOFCFG ) == 0x0000003C, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PHYSET ) == 0x0000003E, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, INTSTS0 ) == 0x00000040, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, INTSTS1 ) == 0x00000042, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, BRDYSTS ) == 0x00000046, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, NRDYSTS ) == 0x00000048, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, BEMPSTS ) == 0x0000004A, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, FRMNUM ) == 0x0000004C, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, UFRMNUM ) == 0x0000004E, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, USBADDR ) == 0x00000050, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, USBREQ ) == 0x00000054, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, USBVAL ) == 0x00000056, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, USBINDX ) == 0x00000058, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, USBLENG ) == 0x0000005A, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DCPCFG ) == 0x0000005C, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DCPMAXP ) == 0x0000005E, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DCPCTR ) == 0x00000060, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PIPESEL ) == 0x00000064, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PIPECFG ) == 0x00000068, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PIPEMAXP ) == 0x0000006C, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PIPEPERI ) == 0x0000006E, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PIPE_CTR ) == 0x00000070, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PIPE_TR ) == 0x00000090, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, USBBCCTRL0 ) == 0x000000B0, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, UCKSEL ) == 0x000000C4, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, USBMC ) == 0x000000CC, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DEVADD ) == 0x000000D0, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PHYSLEW ) == 0x000000F0, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, LPCTRL ) == 0x00000100, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, LPSTS ) == 0x00000102, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, BCCTRL ) == 0x00000140, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PL1CTRL1 ) == 0x00000144, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, PL1CTRL2 ) == 0x00000146, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, HL1CTRL1 ) == 0x00000148, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, HL1CTRL2 ) == 0x0000014A, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DPUSR0R ) == 0x00000160, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DPUSR1R ) == 0x00000164, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DPUSR2R ) == 0x00000168, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DPUSRCR ) == 0x0000016A, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DPUSR0R_FS ) == 0x00000400, "incorrect offset"); -TU_VERIFY_STATIC(offsetof(RUSB2_REG_t, DPUSR1R_FS ) == 0x00000404, "incorrect offset"); +TU_VERIFY_STATIC(sizeof(rusb2_reg_t) == 1032, "incorrect size"); + +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, SYSCFG ) == 0x0000, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, BUSWAIT ) == 0x0002, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, SYSSTS0 ) == 0x0004, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PLLSTA ) == 0x0006, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DVSTCTR0 ) == 0x0008, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, TESTMODE ) == 0x000C, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, CFIFO ) == 0x0014, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, D0FIFO ) == 0x0018, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, D1FIFO ) == 0x001C, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, CFIFOSEL ) == 0x0020, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, CFIFOCTR ) == 0x0022, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, D0FIFOSEL ) == 0x0028, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, D0FIFOCTR ) == 0x002A, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, D1FIFOSEL ) == 0x002C, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, D1FIFOCTR ) == 0x002E, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, INTENB0 ) == 0x0030, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, INTENB1 ) == 0x0032, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, BRDYENB ) == 0x0036, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, NRDYENB ) == 0x0038, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, BEMPENB ) == 0x003A, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, SOFCFG ) == 0x003C, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PHYSET ) == 0x003E, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, INTSTS0 ) == 0x0040, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, INTSTS1 ) == 0x0042, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, BRDYSTS ) == 0x0046, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, NRDYSTS ) == 0x0048, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, BEMPSTS ) == 0x004A, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, FRMNUM ) == 0x004C, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, UFRMNUM ) == 0x004E, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, USBADDR ) == 0x0050, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, USBREQ ) == 0x0054, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, USBVAL ) == 0x0056, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, USBINDX ) == 0x0058, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, USBLENG ) == 0x005A, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DCPCFG ) == 0x005C, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DCPMAXP ) == 0x005E, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DCPCTR ) == 0x0060, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PIPESEL ) == 0x0064, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PIPECFG ) == 0x0068, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PIPEBUF ) == 0x006A, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PIPEMAXP ) == 0x006C, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PIPEPERI ) == 0x006E, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PIPE_CTR ) == 0x0070, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PIPE_TR ) == 0x0090, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, USBBCCTRL0 ) == 0x00B0, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, UCKSEL ) == 0x00C4, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, USBMC ) == 0x00CC, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DEVADD ) == 0x00D0, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PHYSLEW ) == 0x00F0, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, LPCTRL ) == 0x0100, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, LPSTS ) == 0x0102, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, BCCTRL ) == 0x0140, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PL1CTRL1 ) == 0x0144, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PL1CTRL2 ) == 0x0146, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, HL1CTRL1 ) == 0x0148, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, HL1CTRL2 ) == 0x014A, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PHYTRIM1 ) == 0x0150, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, PHYTRIM2 ) == 0x0152, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DPUSR0R ) == 0x0160, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DPUSR1R ) == 0x0164, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DPUSR2R ) == 0x0168, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DPUSRCR ) == 0x016A, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DPUSR0R_FS ) == 0x0400, "incorrect offset"); +TU_VERIFY_STATIC(offsetof(rusb2_reg_t, DPUSR1R_FS ) == 0x0404, "incorrect offset"); #ifdef __cplusplus } -- cgit v1.3.1 From 95b77a0e7356b5f6625fbdb66f35415db3aac7a9 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 6 Jul 2023 15:54:07 +0700 Subject: add rusb2_module_start(), more update for multiple ports for dcd rusb2 --- hw/bsp/ra/family.c | 7 - src/portable/renesas/rusb2/dcd_rusb2.c | 280 +++++++++++++++++++------------- src/portable/renesas/rusb2/rusb2_ra.h | 38 ++--- src/portable/renesas/rusb2/rusb2_rx.h | 6 + src/portable/renesas/rusb2/rusb2_type.h | 1 + 5 files changed, 190 insertions(+), 142 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/ra/family.c b/hw/bsp/ra/family.c index 36b46beab..2c21a9967 100644 --- a/hw/bsp/ra/family.c +++ b/hw/bsp/ra/family.c @@ -104,13 +104,6 @@ void board_init(void) { R_SYSTEM->TRCKCR = R_SYSTEM_TRCKCR_TRCKEN_Msk | 0x01; #endif - // Enable USB module - R_MSTP->MSTPCRB &= ~(1U << 11U); // FS - -#ifdef BOARD_HAS_USB_HIGHSPEED - R_MSTP->MSTPCRB &= ~(1U << 12U); -#endif - #if CFG_TUSB_OS == OPT_OS_FREERTOS // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) NVIC_SetPriority(USBFS_INT_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index b58e0be01..27d525b68 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -65,9 +65,9 @@ /* LINK core registers */ #if defined(__CCRX__) - #define RUSB2 ((RUSB2_REG_t __evenaccess*) RUSB2_REG_BASE) + #define RUSB2 ((rusb2_reg_t __evenaccess*) RUSB2_REG_BASE) #elif defined(__RX__) - #define RUSB2 ((RUSB2_REG_t*) RUSB2_REG_BASE) + #define RUSB2 ((rusb2_reg_t*) RUSB2_REG_BASE) #elif (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) #define RUSB2 ((R_USB_HS0_Type*)R_USB_HS0_BASE) #else @@ -145,10 +145,15 @@ typedef struct uint8_t ep[2][16]; /* a lookup table for a pipe index from an endpoint address */ } dcd_data_t; +static dcd_data_t _dcd; + //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -static dcd_data_t _dcd; + +TU_ATTR_ALWAYS_INLINE static inline bool is_highspeed(uint8_t rhport) { + return rhport == 1; +} static unsigned find_pipe(unsigned xfer) { @@ -543,38 +548,60 @@ static void process_pipe_brdy(uint8_t rhport, unsigned num) static void process_bus_reset(uint8_t rhport) { - RUSB2->BEMPENB = 1; - RUSB2->BRDYENB = 1; - RUSB2->CFIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; - RUSB2->D0FIFOSEL = 0; - while (RUSB2->D0FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ - RUSB2->D1FIFOSEL = 0; - while (RUSB2->D1FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ - volatile uint16_t *ctr = (volatile uint16_t*)((uintptr_t) (&RUSB2->PIPE_CTR[0])); - volatile uint16_t *tre = (volatile uint16_t*)((uintptr_t) (&RUSB2->PIPE_TR[0].E)); + rusb2_reg_t* rusb = RUSB2_REG(rhport); + + rusb->BEMPENB = 1; + rusb->BRDYENB = 1; + rusb->CFIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; + + rusb->D0FIFOSEL = 0; + while (rusb->D0FIFOSEL_b.CURPIPE) {} /* if CURPIPE bits changes, check written value */ + + rusb->D1FIFOSEL = 0; + while (rusb->D1FIFOSEL_b.CURPIPE) {} /* if CURPIPE bits changes, check written value */ + + volatile uint16_t *ctr = (volatile uint16_t*)((uintptr_t) (&rusb->PIPE_CTR[0])); + volatile uint16_t *tre = (volatile uint16_t*)((uintptr_t) (&rusb->PIPE_TR[0].E)); + for (int i = 1; i <= 5; ++i) { - RUSB2->PIPESEL = i; - RUSB2->PIPECFG = 0; + rusb->PIPESEL = i; + rusb->PIPECFG = 0; *ctr = RUSB2_PIPE_CTR_ACLRM_Msk; *ctr = 0; ++ctr; *tre = TU_BIT(8); tre += 2; } + for (int i = 6; i <= 9; ++i) { - RUSB2->PIPESEL = i; - RUSB2->PIPECFG = 0; + rusb->PIPESEL = i; + rusb->PIPECFG = 0; *ctr = RUSB2_PIPE_CTR_ACLRM_Msk; *ctr = 0; ++ctr; } tu_varclr(&_dcd); -#if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) - dcd_event_bus_reset(rhport, TUSB_SPEED_HIGH, true); -#else - dcd_event_bus_reset(rhport, TUSB_SPEED_FULL, true); -#endif + TU_LOG3("Bus reset, RHST = %u\r\n", rusb->DVSTCTR0_b.RHST); + tusb_speed_t speed; + switch(rusb->DVSTCTR0 & RUSB2_DVSTCTR0_RHST_Msk) { + case RUSB2_DVSTCTR0_RHST_LS: + speed = TUSB_SPEED_LOW; + break; + + case RUSB2_DVSTCTR0_RHST_FS: + speed = TUSB_SPEED_FULL; + break; + + case RUSB2_DVSTCTR0_RHST_HS: + speed = TUSB_SPEED_HIGH; + break; + + default: + TU_ASSERT(false, ); + } + + dcd_event_bus_reset(rhport, speed, true); } static void process_set_address(uint8_t rhport) @@ -625,56 +652,63 @@ static void enable_interrupt(uint32_t pswi) void dcd_init(uint8_t rhport) { - (void)rhport; + rusb2_reg_t* rusb = RUSB2_REG(rhport); -#if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) - RUSB2->SYSCFG_b.HSE = 1; - RUSB2->PHYSET_b.DIRPD = 0; - R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MILLISECONDS); - RUSB2->PHYSET_b.PLLRESET = 0; - //RUSB2->PHYSET_b.REPSTART = 1; - RUSB2->SYSCFG_b.DRPD = 0; - RUSB2->SYSCFG_b.USBE = 1; - RUSB2->LPSTS_b.SUSPENDM = 1; - while (!RUSB2->PLLSTA_b.PLLLOCK); - //RUSB2->BUSWAIT |= 0x0F00U; - //RUSB2->PHYSET_b.REPSEL = 1; - RUSB2->CFIFOSEL_b.MBW = 1; - RUSB2->D0FIFOSEL_b.MBW = 1; - RUSB2->D1FIFOSEL_b.MBW = 1; - RUSB2->INTSTS0 = 0; -#else - RUSB2->SYSCFG_b.SCKE = 1; - while (!RUSB2->SYSCFG_b.SCKE) ; - RUSB2->SYSCFG_b.DRPD = 0; - RUSB2->SYSCFG_b.DCFM = 0; - RUSB2->SYSCFG_b.USBE = 1; -#endif + rusb2_module_start(rhport, true); - // MCU specific PHY init - rusb2_phy_init(); + if ( is_highspeed(rhport) ) { + rusb->SYSCFG_b.HSE = 1; -#if (CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) - RUSB2->PHYSLEW = 0x5; - RUSB2->DPUSR0R_FS_b.FIXPHY0 = 0u; /* USB_BASE Transceiver Output fixed */ + // leave CLKSEL as default (0x11) 24Mhz - #define USB_VDCEN (0x0080U) /* b7: Regulator ON/OFF control */ - RUSB2->USBMC = (uint16_t) (RUSB2->USBMC | (USB_VDCEN)); -#endif + // Power and reset UTMI Phy + uint16_t physet = (rusb->PHYSET | RUSB2_PHYSET_PLLRESET_Msk) & ~RUSB2_PHYSET_DIRPD_Msk; + rusb->PHYSET = physet; + R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MILLISECONDS); + rusb->PHYSET_b.PLLRESET = 0; + + // set UTMI to operating mode and wait for PLL lock confirmation + rusb->LPSTS_b.SUSPENDM = 1; + while (!rusb->PLLSTA_b.PLLLOCK) {} + + rusb->SYSCFG_b.DRPD = 0; + rusb->SYSCFG_b.USBE = 1; + + // Set CPU bus wait time (fine tunne later) + // rusb2->BUSWAIT |= 0x0F00U; + + rusb->PHYSET_b.REPSEL = 1; + + rusb->CFIFOSEL_b.MBW = 1; + rusb->D0FIFOSEL_b.MBW = 1; + rusb->D1FIFOSEL_b.MBW = 1; + } else { + rusb->SYSCFG_b.SCKE = 1; + while (!rusb->SYSCFG_b.SCKE) {} + rusb->SYSCFG_b.DRPD = 0; + rusb->SYSCFG_b.DCFM = 0; + rusb->SYSCFG_b.USBE = 1; + + // MCU specific PHY init + rusb2_phy_init(); + + rusb->PHYSLEW = 0x5; + rusb->DPUSR0R_FS_b.FIXPHY0 = 0u; /* USB_BASE Transceiver Output fixed */ + + // rusb2->USBMC = (uint16_t) (rusb2->USBMC | RUSB2_USBMC_VDCEN_Msk); + } /* Setup default control pipe */ - RUSB2->DCPMAXP_b.MXPS = 64; - RUSB2->INTENB0 = RUSB2_INTSTS0_VBINT_Msk | RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_BEMP_Msk | - RUSB2_INTSTS0_DVST_Msk | RUSB2_INTSTS0_CTRT_Msk | (USE_SOF ? RUSB2_INTSTS0_SOFR_Msk : 0) | - RUSB2_INTSTS0_RESM_Msk | RUSB2_INTSTS0_NRDY_Msk; - RUSB2->BEMPENB = 1; - RUSB2->BRDYENB = 1; - -#if (CFG_TUSB_RHPORT0_MODE & OPT_MODE_DEVICE) - RUSB2->SYSCFG_b.DPRPU = 1; /* necessary in this position */ -#endif + rusb->DCPMAXP_b.MXPS = 64; + + rusb->INTSTS0 = 0; + rusb->INTENB0 = RUSB2_INTSTS0_VBINT_Msk | RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_BEMP_Msk | + RUSB2_INTSTS0_DVST_Msk | RUSB2_INTSTS0_CTRT_Msk | (USE_SOF ? RUSB2_INTSTS0_SOFR_Msk : 0) | + RUSB2_INTSTS0_RESM_Msk | RUSB2_INTSTS0_NRDY_Msk; + rusb->BEMPENB = 1; + rusb->BRDYENB = 1; - if (RUSB2->INTSTS0_b.VBSTS) { + if (rusb->INTSTS0_b.VBSTS) { dcd_connect(rhport); } } @@ -697,24 +731,24 @@ void dcd_set_address(uint8_t rhport, uint8_t dev_addr) void dcd_remote_wakeup(uint8_t rhport) { - (void)rhport; - RUSB2->DVSTCTR0_b.WKUP = 1; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + rusb->DVSTCTR0_b.WKUP = 1; } void dcd_connect(uint8_t rhport) { - (void)rhport; - #if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) - RUSB2->SYSCFG_b.CNEN = 1; - R_BSP_SoftwareDelay((uint32_t) 10, BSP_DELAY_UNITS_MILLISECONDS); - #endif - RUSB2->SYSCFG_b.DPRPU = 1; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + + if ( is_highspeed(rhport)) { + rusb->SYSCFG_b.CNEN = 1; + } + rusb->SYSCFG_b.DPRPU = 1; } void dcd_disconnect(uint8_t rhport) { - (void)rhport; - RUSB2->SYSCFG_b.DPRPU = 0; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + rusb->SYSCFG_b.DPRPU = 0; } void dcd_sof_enable(uint8_t rhport, bool en) @@ -861,76 +895,94 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) //--------------------------------------------------------------------+ void dcd_int_handler(uint8_t rhport) { - (void)rhport; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + + uint16_t is0 = rusb->INTSTS0; - unsigned is0 = RUSB2->INTSTS0; /* clear active bits except VALID (don't write 0 to already cleared bits according to the HW manual) */ - RUSB2->INTSTS0 = ~((RUSB2_INTSTS0_CTRT_Msk | RUSB2_INTSTS0_DVST_Msk | RUSB2_INTSTS0_SOFR_Msk | - RUSB2_INTSTS0_RESM_Msk | RUSB2_INTSTS0_VBINT_Msk) & is0) | RUSB2_INTSTS0_VALID_Msk; - if (is0 & RUSB2_INTSTS0_VBINT_Msk) { - if (RUSB2->INTSTS0_b.VBSTS) { + rusb->INTSTS0 = ~((RUSB2_INTSTS0_CTRT_Msk | RUSB2_INTSTS0_DVST_Msk | RUSB2_INTSTS0_SOFR_Msk | + RUSB2_INTSTS0_RESM_Msk | RUSB2_INTSTS0_VBINT_Msk) & is0) | RUSB2_INTSTS0_VALID_Msk; + + // VBUS changes + if ( is0 & RUSB2_INTSTS0_VBINT_Msk ) { + if ( rusb->INTSTS0_b.VBSTS ) { dcd_connect(rhport); } else { dcd_disconnect(rhport); } } - if (is0 & RUSB2_INTSTS0_RESM_Msk) { + + // Resumed + if ( is0 & RUSB2_INTSTS0_RESM_Msk ) { dcd_event_bus_signal(rhport, DCD_EVENT_RESUME, true); -#if (0==USE_SOF) - RUSB2->INTENB0_b.SOFE = 0; +#if (0 == USE_SOF) + rusb->INTENB0_b.SOFE = 0; #endif } - if ((is0 & RUSB2_INTSTS0_SOFR_Msk) && RUSB2->INTENB0_b.SOFE) { + + // SOF received + if ( (is0 & RUSB2_INTSTS0_SOFR_Msk) && rusb->INTENB0_b.SOFE ) { // USBD will exit suspended mode when SOF event is received dcd_event_bus_signal(rhport, DCD_EVENT_SOF, true); #if (0 == USE_SOF) - RUSB2->INTENB0_b.SOFE = 0; + rusb->INTENB0_b.SOFE = 0; #endif } - if (is0 & RUSB2_INTSTS0_DVST_Msk) { + + // Device state changes + if ( is0 & RUSB2_INTSTS0_DVST_Msk ) { switch (is0 & RUSB2_INTSTS0_DVSQ_Msk) { - case RUSB2_INTSTS0_DVSQ_STATE_DEF: - process_bus_reset(rhport); - break; - case RUSB2_INTSTS0_DVSQ_STATE_ADDR: - process_set_address(rhport); - break; - case RUSB2_INTSTS0_DVSQ_STATE_SUSP0: - case RUSB2_INTSTS0_DVSQ_STATE_SUSP1: - case RUSB2_INTSTS0_DVSQ_STATE_SUSP2: - case RUSB2_INTSTS0_DVSQ_STATE_SUSP3: - dcd_event_bus_signal(rhport, DCD_EVENT_SUSPEND, true); -#if (0==USE_SOF) - RUSB2->INTENB0_b.SOFE = 1; + case RUSB2_INTSTS0_DVSQ_STATE_DEF: + process_bus_reset(rhport); + break; + + case RUSB2_INTSTS0_DVSQ_STATE_ADDR: + process_set_address(rhport); + break; + + case RUSB2_INTSTS0_DVSQ_STATE_SUSP0: + case RUSB2_INTSTS0_DVSQ_STATE_SUSP1: + case RUSB2_INTSTS0_DVSQ_STATE_SUSP2: + case RUSB2_INTSTS0_DVSQ_STATE_SUSP3: + dcd_event_bus_signal(rhport, DCD_EVENT_SUSPEND, true); +#if (0 == USE_SOF) + rusb->INTENB0_b.SOFE = 1; #endif - default: - break; + + default: break; } } - if (is0 & RUSB2_INTSTS0_NRDY_Msk) { - RUSB2->NRDYSTS = 0; + + if ( is0 & RUSB2_INTSTS0_NRDY_Msk ) { + rusb->NRDYSTS = 0; } - if (is0 & RUSB2_INTSTS0_CTRT_Msk) { - if (is0 & RUSB2_INTSTS0_CTSQ_CTRL_RDATA) { + + // Control transfer stage changes + if ( is0 & RUSB2_INTSTS0_CTRT_Msk ) { + if ( is0 & RUSB2_INTSTS0_CTSQ_CTRL_RDATA ) { /* A setup packet has been received. */ process_setup_packet(rhport); - } else if (0 == (is0 & RUSB2_INTSTS0_CTSQ_Msk)) { + } else if ( 0 == (is0 & RUSB2_INTSTS0_CTSQ_Msk) ) { /* A ZLP has been sent/received. */ process_status_completion(rhport); } } - if (is0 & RUSB2_INTSTS0_BEMP_Msk) { - const unsigned s = RUSB2->BEMPSTS; - RUSB2->BEMPSTS = 0; - if (s & 1) { + + // Buffer empty + if ( is0 & RUSB2_INTSTS0_BEMP_Msk ) { + const unsigned s = rusb->BEMPSTS; + rusb->BEMPSTS = 0; + if ( s & 1 ) { process_pipe0_bemp(rhport); } } - if (is0 & RUSB2_INTSTS0_BRDY_Msk) { - const unsigned m = RUSB2->BRDYENB; - unsigned s = RUSB2->BRDYSTS & m; + + // Buffer ready + if ( is0 & RUSB2_INTSTS0_BRDY_Msk ) { + const unsigned m = rusb->BRDYENB; + unsigned s = rusb->BRDYSTS & m; /* clear active bits (don't write 0 to already cleared bits according to the HW manual) */ - RUSB2->BRDYSTS = ~s; + rusb->BRDYSTS = ~s; while (s) { #if defined(__CCRX__) static const int Mod37BitPosition[] = { diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index ca7c38907..0dc59331a 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -76,38 +76,34 @@ static rusb2_controller_t rusb2_controller[] = { #endif }; -TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_enable(uint8_t rhport) -{ - #if RUSB2_CONTROLLER_COUNT > 1 +#define RUSB2_REG(_p) ((rusb2_reg_t*) rusb2_controller[_p].reg_base) + +TU_ATTR_ALWAYS_INLINE static inline void rusb2_module_start(uint8_t rhport, bool start) { + uint32_t const mask = 1U << (11+rhport); + if (start) { + R_MSTP->MSTPCRB &= ~mask; + }else { + R_MSTP->MSTPCRB |= mask; + } +} + +TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_enable(uint8_t rhport) { NVIC_EnableIRQ(rusb2_controller[rhport].irqnum); - #else - (void) rhport; - NVIC_EnableIRQ(rusb2_controller[0].irqnum); - #endif } -TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_disable(uint8_t rhport) -{ - #if RUSB2_CONTROLLER_COUNT > 1 +TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_disable(uint8_t rhport) { NVIC_DisableIRQ(rusb2_controller[rhport].irqnum); - #else - (void) rhport; - NVIC_DisableIRQ(rusb2_controller[0].irqnum); - #endif } // MCU specific PHY init -TU_ATTR_ALWAYS_INLINE static inline void rusb2_phy_init(void) -{ +TU_ATTR_ALWAYS_INLINE static inline void rusb2_phy_init(void) { } +//--------------------------------------------------------------------+ +// Application API for setting IRQ number +//--------------------------------------------------------------------+ void tud_int_set_irqnum(uint8_t rhport, int32_t irqnum) { - #if RUSB2_CONTROLLER_COUNT > 1 rusb2_controller[rhport].irqnum = irqnum; - #else - (void) rhport; - rusb2_controller[0].irqnum = irqnum; - #endif } #ifdef __cplusplus diff --git a/src/portable/renesas/rusb2/rusb2_rx.h b/src/portable/renesas/rusb2/rusb2_rx.h index 397c0d56c..d7f4e0b42 100644 --- a/src/portable/renesas/rusb2/rusb2_rx.h +++ b/src/portable/renesas/rusb2/rusb2_rx.h @@ -37,6 +37,12 @@ extern "C" { #define RUSB2_REG_BASE (0x000A0000) +// Start/Stop MSTP TODO implement later +TU_ATTR_ALWAYS_INLINE static inline void rusb2_module_start(uint8_t rhport, bool start) { + (void) rhport; + (void) start; +} + TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_enable(uint8_t rhport) { (void) rhport; diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index 0928f5aeb..b704626f6 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -1653,6 +1653,7 @@ TU_ATTR_BIT_FIELD_ORDER_END #define RUSB2_DVSTCTR0_RHST_LS (1U << RUSB2_DVSTCTR0_RHST_Pos) /* Low-speed connection */ #define RUSB2_DVSTCTR0_RHST_FS (2U << RUSB2_DVSTCTR0_RHST_Pos) /* Full-speed connection */ +#define RUSB2_DVSTCTR0_RHST_HS (3U << RUSB2_DVSTCTR0_RHST_Pos) /* Full-speed connection */ #define RUSB2_DEVADD_USBSPD_LS (1U << RUSB2_DEVADD_USBSPD_Pos) /* Target Device Low-speed */ #define RUSB2_DEVADD_USBSPD_FS (2U << RUSB2_DEVADD_USBSPD_Pos) /* Target Device Full-speed */ -- cgit v1.3.1 From 1eefc2b3ef2e268e839002a8b5221eebe26f6cd3 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 6 Jul 2023 19:35:42 +0700 Subject: more multiple ports update --- src/portable/renesas/rusb2/dcd_rusb2.c | 344 ++++++++++++++++++-------------- src/portable/renesas/rusb2/rusb2_rx.h | 2 + src/portable/renesas/rusb2/rusb2_type.h | 9 +- 3 files changed, 208 insertions(+), 147 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 27d525b68..833737181 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -63,22 +63,11 @@ // MACRO TYPEDEF CONSTANT ENUM //--------------------------------------------------------------------+ -/* LINK core registers */ -#if defined(__CCRX__) - #define RUSB2 ((rusb2_reg_t __evenaccess*) RUSB2_REG_BASE) -#elif defined(__RX__) - #define RUSB2 ((rusb2_reg_t*) RUSB2_REG_BASE) -#elif (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) - #define RUSB2 ((R_USB_HS0_Type*)R_USB_HS0_BASE) -#else - #define RUSB2 ((R_USB_FS0_Type*)R_USB_FS0_BASE) -#endif - /* Start of definition of packed structs (used by the CCRX toolchain) */ TU_ATTR_PACKED_BEGIN TU_ATTR_BIT_FIELD_ORDER_BEGIN -typedef struct TU_ATTR_PACKED { +typedef struct TU_ATTR_PACKED _ccrx_evenaccess { union { struct { uint16_t : 8; @@ -186,52 +175,53 @@ static unsigned find_pipe(unsigned xfer) return 0; } -static volatile uint16_t* get_pipectr(unsigned num) +static volatile uint16_t* get_pipectr(rusb2_reg_t *rusb, unsigned num) { if (num) { - return (volatile uint16_t*)&(RUSB2->PIPE_CTR[num - 1]); + return (volatile uint16_t*)&(rusb->PIPE_CTR[num - 1]); } else { - return (volatile uint16_t*)&(RUSB2->DCPCTR); + return (volatile uint16_t*)&(rusb->DCPCTR); } } -static volatile reg_pipetre_t* get_pipetre(unsigned num) +static volatile reg_pipetre_t* get_pipetre(rusb2_reg_t *rusb, unsigned num) { volatile reg_pipetre_t* tre = NULL; if ((1 <= num) && (num <= 5)) { - tre = (volatile reg_pipetre_t*)&(RUSB2->PIPE_TR[num - 1].E); + tre = (volatile reg_pipetre_t*)&(rusb->PIPE_TR[num - 1].E); } return tre; } static volatile uint16_t* ep_addr_to_pipectr(uint8_t rhport, unsigned ep_addr) { - (void)rhport; + rusb2_reg_t *rusb = RUSB2_REG(rhport); const unsigned epn = tu_edpt_number(ep_addr); + if (epn) { const unsigned dir = tu_edpt_dir(ep_addr); const unsigned num = _dcd.ep[dir][epn]; - return get_pipectr(num); + return get_pipectr(rusb, num); } else { - return get_pipectr(0); + return get_pipectr(rusb, 0); } } -static unsigned edpt0_max_packet_size(void) +static uint16_t edpt0_max_packet_size(rusb2_reg_t* rusb) { - return RUSB2->DCPMAXP_b.MXPS; + return rusb->DCPMAXP_b.MXPS; } -static unsigned edpt_max_packet_size(unsigned num) +static uint16_t edpt_max_packet_size(rusb2_reg_t *rusb, unsigned num) { - RUSB2->PIPESEL = num; - return RUSB2->PIPEMAXP; + rusb->PIPESEL = num; + return rusb->PIPEMAXP; } -static inline void pipe_wait_for_ready(unsigned num) +static inline void pipe_wait_for_ready(rusb2_reg_t * rusb, unsigned num) { - while (RUSB2->D0FIFOSEL_b.CURPIPE != num) ; - while (!RUSB2->D0FIFOCTR_b.FRDY) ; + while ( rusb->D0FIFOSEL_b.CURPIPE != num ) {} + while ( !rusb->D0FIFOCTR_b.FRDY ) {} } static void pipe_write_packet(void *buf, volatile void *fifo, unsigned len) @@ -284,61 +274,70 @@ static void pipe_read_write_packet_ff(tu_fifo_t *f, volatile void *fifo, unsigne ops[dir].tu_fifo_advance(f, total_len - rem); } -static bool pipe0_xfer_in(void) +static bool pipe0_xfer_in(rusb2_reg_t* rusb) { pipe_state_t *pipe = &_dcd.pipe[0]; const unsigned rem = pipe->remaining; + if (!rem) { pipe->buf = NULL; return true; } - const unsigned mps = edpt0_max_packet_size(); - const unsigned len = TU_MIN(mps, rem); + + const uint16_t mps = edpt0_max_packet_size(rusb); + const uint16_t len = tu_min16(mps, rem); void *buf = pipe->buf; + if (len) { if (pipe->ff) { - pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&RUSB2->CFIFO, len, TUSB_DIR_IN); + pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len, TUSB_DIR_IN); } else { - pipe_write_packet(buf, (volatile void*)&RUSB2->CFIFO, len); + pipe_write_packet(buf, (volatile void*)&rusb->CFIFO, len); pipe->buf = (uint8_t*)buf + len; } } + if (len < mps) { - RUSB2->CFIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + rusb->CFIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; } + pipe->remaining = rem - len; return false; } -static bool pipe0_xfer_out(void) +static bool pipe0_xfer_out(rusb2_reg_t* rusb) { pipe_state_t *pipe = &_dcd.pipe[0]; const unsigned rem = pipe->remaining; - const unsigned mps = edpt0_max_packet_size(); - const unsigned vld = RUSB2->CFIFOCTR_b.DTLN; - const unsigned len = TU_MIN(TU_MIN(rem, mps), vld); + const uint16_t mps = edpt0_max_packet_size(rusb); + const uint16_t vld = rusb->CFIFOCTR_b.DTLN; + const uint16_t len = tu_min16(tu_min16(rem, mps), vld); void *buf = pipe->buf; + if (len) { if (pipe->ff) { - pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&RUSB2->CFIFO, len, TUSB_DIR_OUT); + pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len, TUSB_DIR_OUT); } else { - pipe_read_packet(buf, (volatile void*)&RUSB2->CFIFO, len); + pipe_read_packet(buf, (volatile void*)&rusb->CFIFO, len); pipe->buf = (uint8_t*)buf + len; } } + if (len < mps) { - RUSB2->CFIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; + rusb->CFIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; } + pipe->remaining = rem - len; if ((len < mps) || (rem == len)) { pipe->buf = NULL; return true; } + return false; } -static bool pipe_xfer_in(unsigned num) +static bool pipe_xfer_in(rusb2_reg_t* rusb, unsigned num) { pipe_state_t *pipe = &_dcd.pipe[num]; const unsigned rem = pipe->remaining; @@ -348,119 +347,141 @@ static bool pipe_xfer_in(unsigned num) return true; } - RUSB2->D0FIFOSEL = num | RUSB2_FIFOSEL_MBW_16BIT | (TU_BYTE_ORDER == TU_BIG_ENDIAN ? RUSB2_FIFOSEL_BIGEND : 0); - const unsigned mps = edpt_max_packet_size(num); - pipe_wait_for_ready(num); - const unsigned len = TU_MIN(rem, mps); + rusb->D0FIFOSEL = num | RUSB2_FIFOSEL_MBW_16BIT | (TU_BYTE_ORDER == TU_BIG_ENDIAN ? RUSB2_FIFOSEL_BIGEND : 0); + const uint16_t mps = edpt_max_packet_size(rusb, num); + pipe_wait_for_ready(rusb, num); + const uint16_t len = tu_min16(rem, mps); void *buf = pipe->buf; + if (len) { if (pipe->ff) { - pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&RUSB2->D0FIFO, len, TUSB_DIR_IN); + pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len, TUSB_DIR_IN); } else { - pipe_write_packet(buf, (volatile void*)&RUSB2->D0FIFO, len); + pipe_write_packet(buf, (volatile void*)&rusb->D0FIFO, len); pipe->buf = (uint8_t*)buf + len; } } + if (len < mps) { - RUSB2->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; } - RUSB2->D0FIFOSEL = 0; - while (RUSB2->D0FIFOSEL_b.CURPIPE) {} /* if CURPIPE bits changes, check written value */ + + rusb->D0FIFOSEL = 0; + while (rusb->D0FIFOSEL_b.CURPIPE) {} /* if CURPIPE bits changes, check written value */ + pipe->remaining = rem - len; + return false; } -static bool pipe_xfer_out(unsigned num) +static bool pipe_xfer_out(rusb2_reg_t* rusb, unsigned num) { pipe_state_t *pipe = &_dcd.pipe[num]; - const unsigned rem = pipe->remaining; + const uint16_t rem = pipe->remaining; - RUSB2->D0FIFOSEL = num | RUSB2_FIFOSEL_MBW_8BIT; - const unsigned mps = edpt_max_packet_size(num); - pipe_wait_for_ready(num); - const unsigned vld = RUSB2->D0FIFOCTR_b.DTLN; - const unsigned len = TU_MIN(TU_MIN(rem, mps), vld); + rusb->D0FIFOSEL = num | RUSB2_FIFOSEL_MBW_8BIT; + const uint16_t mps = edpt_max_packet_size(rusb, num); + pipe_wait_for_ready(rusb, num); + + const uint16_t vld = rusb->D0FIFOCTR_b.DTLN; + const uint16_t len = tu_min16(tu_min16(rem, mps), vld); void *buf = pipe->buf; + if (len) { if (pipe->ff) { - pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&RUSB2->D0FIFO, len, TUSB_DIR_OUT); + pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len, TUSB_DIR_OUT); } else { - pipe_read_packet(buf, (volatile void*)&RUSB2->D0FIFO, len); + pipe_read_packet(buf, (volatile void*)&rusb->D0FIFO, len); pipe->buf = (uint8_t*)buf + len; } } + if (len < mps) { - RUSB2->D0FIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; + rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; } - RUSB2->D0FIFOSEL = 0; - while (RUSB2->D0FIFOSEL_b.CURPIPE) {} /* if CURPIPE bits changes, check written value */ + + rusb->D0FIFOSEL = 0; + while (rusb->D0FIFOSEL_b.CURPIPE) {} /* if CURPIPE bits changes, check written value */ + pipe->remaining = rem - len; if ((len < mps) || (rem == len)) { pipe->buf = NULL; return NULL != buf; } + return false; } static void process_setup_packet(uint8_t rhport) { - uint16_t setup_packet[4]; - if (0 == (RUSB2->INTSTS0 & RUSB2_INTSTS0_VALID_Msk)) return; - RUSB2->CFIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; - setup_packet[0] = tu_le16toh(RUSB2->USBREQ); - setup_packet[1] = RUSB2->USBVAL; - setup_packet[2] = RUSB2->USBINDX; - setup_packet[3] = RUSB2->USBLENG; - RUSB2->INTSTS0 = ~((uint16_t)RUSB2_INTSTS0_VALID_Msk); + rusb2_reg_t* rusb = RUSB2_REG(rhport); + if (0 == (rusb->INTSTS0 & RUSB2_INTSTS0_VALID_Msk)) return; + + rusb->CFIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; + uint16_t setup_packet[4] = { + tu_htole16(rusb->USBREQ), + tu_htole16(rusb->USBVAL), + tu_htole16(rusb->USBINDX), + tu_htole16(rusb->USBLENG) + }; + + rusb->INTSTS0 = ~((uint16_t) RUSB2_INTSTS0_VALID_Msk); dcd_event_setup_received(rhport, (const uint8_t*)&setup_packet[0], true); } static void process_status_completion(uint8_t rhport) { + rusb2_reg_t* rusb = RUSB2_REG(rhport); uint8_t ep_addr; /* Check the data stage direction */ - if (RUSB2->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE) { + if (rusb->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE) { /* IN transfer. */ ep_addr = tu_edpt_addr(0, TUSB_DIR_IN); } else { /* OUT transfer. */ ep_addr = tu_edpt_addr(0, TUSB_DIR_OUT); } + dcd_event_xfer_complete(rhport, ep_addr, 0, XFER_RESULT_SUCCESS, true); } -static bool process_pipe0_xfer(int buffer_type, uint8_t ep_addr, void* buffer, uint16_t total_bytes) +static bool process_pipe0_xfer(rusb2_reg_t* rusb, int buffer_type, uint8_t ep_addr, void* buffer, uint16_t total_bytes) { /* configure fifo direction and access unit settings */ - if (ep_addr) { /* IN, 2 bytes */ - RUSB2->CFIFOSEL = RUSB2_CFIFOSEL_ISEL_WRITE | RUSB2_FIFOSEL_MBW_16BIT | - (TU_BYTE_ORDER == TU_BIG_ENDIAN ? RUSB2_FIFOSEL_BIGEND : 0); - while (!(RUSB2->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE)) ; - } else { /* OUT, a byte */ - RUSB2->CFIFOSEL = RUSB2_FIFOSEL_MBW_8BIT; - while (RUSB2->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE) ; + if ( ep_addr ) { + /* IN, 2 bytes */ + rusb->CFIFOSEL = RUSB2_CFIFOSEL_ISEL_WRITE | RUSB2_FIFOSEL_MBW_16BIT | + (TU_BYTE_ORDER == TU_BIG_ENDIAN ? RUSB2_FIFOSEL_BIGEND : 0); + while ( !(rusb->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE) ) {} + } else { + /* OUT, a byte */ + rusb->CFIFOSEL = RUSB2_FIFOSEL_MBW_8BIT; + while ( rusb->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE ) {} } pipe_state_t *pipe = &_dcd.pipe[0]; pipe->ff = buffer_type; pipe->length = total_bytes; pipe->remaining = total_bytes; - if (total_bytes) { - pipe->buf = buffer; - if (ep_addr) { /* IN */ - TU_ASSERT(RUSB2->DCPCTR_b.BSTS && (RUSB2->USBREQ & 0x80)); - pipe0_xfer_in(); + + if ( total_bytes ) { + pipe->buf = buffer; + if ( ep_addr ) { + /* IN */ + TU_ASSERT(rusb->DCPCTR_b.BSTS && (rusb->USBREQ & 0x80)); + pipe0_xfer_in(rusb); } - RUSB2->DCPCTR = RUSB2_PIPE_CTR_PID_BUF; + rusb->DCPCTR = RUSB2_PIPE_CTR_PID_BUF; } else { /* ZLP */ - pipe->buf = NULL; - RUSB2->DCPCTR = RUSB2_DCPCTR_CCPL_Msk | RUSB2_PIPE_CTR_PID_BUF; + pipe->buf = NULL; + rusb->DCPCTR = RUSB2_DCPCTR_CCPL_Msk | RUSB2_PIPE_CTR_PID_BUF; } + return true; } -static bool process_pipe_xfer(int buffer_type, uint8_t ep_addr, void* buffer, uint16_t total_bytes) +static bool process_pipe_xfer(rusb2_reg_t* rusb, int buffer_type, uint8_t ep_addr, void* buffer, uint16_t total_bytes) { const unsigned epn = tu_edpt_number(ep_addr); const unsigned dir = tu_edpt_dir(ep_addr); @@ -473,49 +494,55 @@ static bool process_pipe_xfer(int buffer_type, uint8_t ep_addr, void* buffer, ui pipe->buf = buffer; pipe->length = total_bytes; pipe->remaining = total_bytes; - if (dir) { /* IN */ + + if (dir) { + /* IN */ if (total_bytes) { - pipe_xfer_in(num); - } else { /* ZLP */ - RUSB2->D0FIFOSEL = num; - pipe_wait_for_ready(num); - RUSB2->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; - RUSB2->D0FIFOSEL = 0; - while (RUSB2->D0FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ + pipe_xfer_in(rusb, num); + } else { + /* ZLP */ + rusb->D0FIFOSEL = num; + pipe_wait_for_ready(rusb, num); + rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + rusb->D0FIFOSEL = 0; + /* if CURPIPE bits changes, check written value */ + while (rusb->D0FIFOSEL_b.CURPIPE) {} } } else { -#if defined(__CCRX__) - __evenaccess volatile reg_pipetre_t *pt = get_pipetre(num); -#else - volatile reg_pipetre_t *pt = get_pipetre(num); -#endif + // OUT + volatile reg_pipetre_t *pt = get_pipetre(rusb, num); + if (pt) { - const unsigned mps = edpt_max_packet_size(num); - volatile uint16_t *ctr = get_pipectr(num); + const uint16_t mps = edpt_max_packet_size(rusb, num); + volatile uint16_t *ctr = get_pipectr(rusb, num); + if (*ctr & 0x3) *ctr = RUSB2_PIPE_CTR_PID_NAK; + pt->TRE = TU_BIT(8); pt->TRN = (total_bytes + mps - 1) / mps; pt->TRENB = 1; *ctr = RUSB2_PIPE_CTR_PID_BUF; } } - // TU_LOG1("X %x %d %d\r\n", ep_addr, total_bytes, buffer_type); + + // TU_LOG2("X %x %d %d\r\n", ep_addr, total_bytes, buffer_type); return true; } -static bool process_edpt_xfer(int buffer_type, uint8_t ep_addr, void* buffer, uint16_t total_bytes) +static bool process_edpt_xfer(rusb2_reg_t* rusb, int buffer_type, uint8_t ep_addr, void* buffer, uint16_t total_bytes) { const unsigned epn = tu_edpt_number(ep_addr); if (0 == epn) { - return process_pipe0_xfer(buffer_type, ep_addr, buffer, total_bytes); + return process_pipe0_xfer(rusb, buffer_type, ep_addr, buffer, total_bytes); } else { - return process_pipe_xfer(buffer_type, ep_addr, buffer, total_bytes); + return process_pipe_xfer(rusb, buffer_type, ep_addr, buffer, total_bytes); } } static void process_pipe0_bemp(uint8_t rhport) { - bool completed = pipe0_xfer_in(); + rusb2_reg_t* rusb = RUSB2_REG(rhport); + bool completed = pipe0_xfer_in(rusb); if (completed) { pipe_state_t *pipe = &_dcd.pipe[0]; dcd_event_xfer_complete(rhport, tu_edpt_addr(0, TUSB_DIR_IN), @@ -525,17 +552,20 @@ static void process_pipe0_bemp(uint8_t rhport) static void process_pipe_brdy(uint8_t rhport, unsigned num) { + rusb2_reg_t* rusb = RUSB2_REG(rhport); pipe_state_t *pipe = &_dcd.pipe[num]; const unsigned dir = tu_edpt_dir(pipe->ep); bool completed; - if (dir) { /* IN */ - completed = pipe_xfer_in(num); + if (dir) { + /* IN */ + completed = pipe_xfer_in(rusb, num); } else { + // OUT if (num) { - completed = pipe_xfer_out(num); + completed = pipe_xfer_out(rusb, num); } else { - completed = pipe0_xfer_out(); + completed = pipe0_xfer_out(rusb); } } if (completed) { @@ -606,8 +636,10 @@ static void process_bus_reset(uint8_t rhport) static void process_set_address(uint8_t rhport) { - const uint32_t addr = RUSB2->USBADDR & 0xFF; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + const uint32_t addr = rusb->USBADDR & 0xFF; if (!addr) return; + const tusb_control_request_t setup_packet = { #if defined(__CCRX__) .bmRequestType = { 0 }, /* Note: CCRX needs the braces over this struct member */ @@ -618,8 +650,9 @@ static void process_set_address(uint8_t rhport) .wValue = addr, .wIndex = 0, .wLength = 0, - }; - dcd_event_setup_received(rhport, (const uint8_t*)&setup_packet, true); + }; + + dcd_event_setup_received(rhport, (const uint8_t *) &setup_packet, true); } /*------------------------------------------------------------------*/ @@ -704,7 +737,7 @@ void dcd_init(uint8_t rhport) rusb->INTSTS0 = 0; rusb->INTENB0 = RUSB2_INTSTS0_VBINT_Msk | RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_BEMP_Msk | RUSB2_INTSTS0_DVST_Msk | RUSB2_INTSTS0_CTRT_Msk | (USE_SOF ? RUSB2_INTSTS0_SOFR_Msk : 0) | - RUSB2_INTSTS0_RESM_Msk | RUSB2_INTSTS0_NRDY_Msk; + RUSB2_INTSTS0_RESM_Msk; rusb->BEMPENB = 1; rusb->BRDYENB = 1; @@ -766,33 +799,43 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) { (void)rhport; + rusb2_reg_t * rusb = RUSB2_REG(rhport); const unsigned ep_addr = ep_desc->bEndpointAddress; const unsigned epn = tu_edpt_number(ep_addr); const unsigned dir = tu_edpt_dir(ep_addr); const unsigned xfer = ep_desc->bmAttributes.xfer; const unsigned mps = tu_edpt_packet_size(ep_desc); - if (xfer == TUSB_XFER_ISOCHRONOUS && mps > 256) { - /* USBa supports up to 256 bytes */ - return false; + + if (xfer == TUSB_XFER_ISOCHRONOUS) { + // Fullspeed ISO is limit to 256 bytes + if ( !is_highspeed(rhport) && mps > 256) { + return false; + } } const unsigned num = find_pipe(xfer); - if (!num) return false; + TU_ASSERT(num); + _dcd.pipe[num].ep = ep_addr; _dcd.ep[dir][epn] = num; /* setup pipe */ dcd_int_disable(rhport); - #if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) - RUSB2->PIPEBUF = 0x7C08; - #endif - RUSB2->PIPESEL = num; - RUSB2->PIPEMAXP = mps; - volatile uint16_t *ctr = get_pipectr(num); + + if ( is_highspeed(rhport) ) { + // FIXME shouldn't be after pipe selection and config, also the BUFNMB should be changed + // depending on the allocation scheme + rusb->PIPEBUF = 0x7C08; + } + + rusb->PIPESEL = num; + rusb->PIPEMAXP = mps; + volatile uint16_t *ctr = get_pipectr(rusb, num); *ctr = RUSB2_PIPE_CTR_ACLRM_Msk | RUSB2_PIPE_CTR_SQCLR_Msk; *ctr = 0; unsigned cfg = (dir << 4) | epn; + if (xfer == TUSB_XFER_BULK) { cfg |= (RUSB2_PIPECFG_TYPE_BULK | RUSB2_PIPECFG_SHTNAK_Msk | RUSB2_PIPECFG_DBLB_Msk); } else if (xfer == TUSB_XFER_INTERRUPT) { @@ -800,13 +843,16 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) } else { cfg |= (RUSB2_PIPECFG_TYPE_ISO | RUSB2_PIPECFG_DBLB_Msk); } - RUSB2->PIPECFG = cfg; - RUSB2->BRDYSTS = 0x1FFu ^ TU_BIT(num); - RUSB2->BRDYENB |= TU_BIT(num); + + rusb->PIPECFG = cfg; + rusb->BRDYSTS = 0x1FFu ^ TU_BIT(num); + rusb->BRDYENB |= TU_BIT(num); + if (dir || (xfer != TUSB_XFER_BULK)) { *ctr = RUSB2_PIPE_CTR_PID_BUF; } - // TU_LOG1("O %d %x %x\r\n", RUSB2->PIPESEL, RUSB2->PIPECFG, RUSB2->PIPEMAXP); + + // TU_LOG1("O %d %x %x\r\n", rusb->PIPESEL, rusb->PIPECFG, rusb->PIPEMAXP); dcd_int_enable(rhport); return true; @@ -826,26 +872,28 @@ void dcd_edpt_close_all(uint8_t rhport) void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) { - (void)rhport; + rusb2_reg_t * rusb = RUSB2_REG(rhport); const unsigned epn = tu_edpt_number(ep_addr); const unsigned dir = tu_edpt_dir(ep_addr); const unsigned num = _dcd.ep[dir][epn]; - RUSB2->BRDYENB &= ~TU_BIT(num); - volatile uint16_t *ctr = get_pipectr(num); + rusb->BRDYENB &= ~TU_BIT(num); + volatile uint16_t *ctr = get_pipectr(rusb, num); *ctr = 0; - RUSB2->PIPESEL = num; - RUSB2->PIPECFG = 0; + rusb->PIPESEL = num; + rusb->PIPECFG = 0; _dcd.pipe[num].ep = 0; _dcd.ep[dir][epn] = 0; } bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes) { - bool r; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + dcd_int_disable(rhport); - r = process_edpt_xfer(0, ep_addr, buffer, total_bytes); + bool r = process_edpt_xfer(rusb, 0, ep_addr, buffer, total_bytes); dcd_int_enable(rhport); + return r; } @@ -853,10 +901,12 @@ bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16_ { // USB buffers always work in bytes so to avoid unnecessary divisions we demand item_size = 1 TU_ASSERT(ff->item_size == 1); - bool r; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + dcd_int_disable(rhport); - r = process_edpt_xfer(1, ep_addr, ff, total_bytes); + bool r = process_edpt_xfer(rusb, 1, ep_addr, ff, total_bytes); dcd_int_enable(rhport); + return r; } @@ -873,8 +923,10 @@ void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { + rusb2_reg_t * rusb = RUSB2_REG(rhport); volatile uint16_t *ctr = ep_addr_to_pipectr(rhport, ep_addr); if (!ctr) return; + dcd_int_disable(rhport); *ctr = RUSB2_PIPE_CTR_SQCLR_Msk; @@ -882,8 +934,8 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) *ctr = RUSB2_PIPE_CTR_PID_BUF; } else { const unsigned num = _dcd.ep[0][tu_edpt_number(ep_addr)]; - RUSB2->PIPESEL = num; - if (RUSB2->PIPECFG_b.TYPE != 1) { + rusb->PIPESEL = num; + if (rusb->PIPECFG_b.TYPE != 1) { *ctr = RUSB2_PIPE_CTR_PID_BUF; } } @@ -953,9 +1005,9 @@ void dcd_int_handler(uint8_t rhport) } } - if ( is0 & RUSB2_INTSTS0_NRDY_Msk ) { - rusb->NRDYSTS = 0; - } +// if ( is0 & RUSB2_INTSTS0_NRDY_Msk ) { +// rusb->NRDYSTS = 0; +// } // Control transfer stage changes if ( is0 & RUSB2_INTSTS0_CTRT_Msk ) { @@ -970,7 +1022,7 @@ void dcd_int_handler(uint8_t rhport) // Buffer empty if ( is0 & RUSB2_INTSTS0_BEMP_Msk ) { - const unsigned s = rusb->BEMPSTS; + const uint16_t s = rusb->BEMPSTS; rusb->BEMPSTS = 0; if ( s & 1 ) { process_pipe0_bemp(rhport); diff --git a/src/portable/renesas/rusb2/rusb2_rx.h b/src/portable/renesas/rusb2/rusb2_rx.h index d7f4e0b42..21b2527c3 100644 --- a/src/portable/renesas/rusb2/rusb2_rx.h +++ b/src/portable/renesas/rusb2/rusb2_rx.h @@ -37,6 +37,8 @@ extern "C" { #define RUSB2_REG_BASE (0x000A0000) +#define RUSB2_REG(_p) ((rusb2_reg_t *) RUSB2_REG_BASE) + // Start/Stop MSTP TODO implement later TU_ATTR_ALWAYS_INLINE static inline void rusb2_module_start(uint8_t rhport, bool start) { (void) rhport; diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index b704626f6..7a5e37089 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -33,6 +33,13 @@ extern "C" { #endif +// CCRX specific attribute to generate a Code that Accesses Variables in the Declared Size +#ifdef __CCRX__ + #define _ccrx_evenaccess __evenaccess +#else + #define _ccrx_evenaccess +#endif + /*--------------------------------------------------------------------*/ /* Register Definitions */ /*--------------------------------------------------------------------*/ @@ -64,7 +71,7 @@ typedef struct { /* RUSB2 Registers Structure */ -typedef struct { +typedef struct _ccrx_evenaccess { union { volatile uint16_t SYSCFG; /* (@ 0x00000000) System Configuration Control Register */ -- cgit v1.3.1 From c53acb145589e2733b7d1abe012e85ae590bffb7 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 6 Jul 2023 20:10:58 +0700 Subject: fix build with rx --- src/portable/renesas/rusb2/dcd_rusb2.c | 37 +++++++++++++++++++--------------- src/portable/renesas/rusb2/rusb2_ra.h | 4 ++-- src/portable/renesas/rusb2/rusb2_rx.h | 5 ++++- 3 files changed, 27 insertions(+), 19 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 833737181..81b60b3bc 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -36,12 +36,6 @@ #include "device/dcd.h" #include "rusb2_type.h" -#if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE) -// fallback -#define CFG_TUSB_RHPORT0_MODE OPT_MODE_DEVICE -#define CFG_TUSB_RHPORT1_MODE 0 -#endif - #if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) #include "rusb2_rx.h" #elif TU_CHECK_MCU(OPT_MCU_RAXXX) @@ -86,7 +80,7 @@ typedef union TU_ATTR_PACKED { volatile uint8_t reserved8; }; volatile uint16_t u16; -} hw_fifo_t; +} hw_fifo16_t; typedef union TU_ATTR_PACKED { struct { @@ -140,9 +134,11 @@ static dcd_data_t _dcd; // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -TU_ATTR_ALWAYS_INLINE static inline bool is_highspeed(uint8_t rhport) { - return rhport == 1; -} +#ifdef RUSB2_SUPPORT_HIGHSPEED + #define is_highspeed_usbip(_p) (_p == 1) +#else + #define is_highspeed_usbip(_p) (false) +#endif static unsigned find_pipe(unsigned xfer) { @@ -229,14 +225,17 @@ static void pipe_write_packet(void *buf, volatile void *fifo, unsigned len) #if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) volatile hw_fifo32_t *reg = (volatile hw_fifo32_t*) fifo; #else - volatile hw_fifo_t *reg = (volatile hw_fifo_t*) fifo; + volatile hw_fifo16_t *reg = (volatile hw_fifo16_t*) fifo; #endif + uintptr_t addr = (uintptr_t)buf; + while (len >= 2) { reg->u16 = *(const uint16_t *)addr; addr += 2; len -= 2; } + if (len > 0) { reg->u8 = *(const uint8_t *)addr; ++addr; @@ -260,11 +259,14 @@ static void pipe_read_write_packet_ff(tu_fifo_t *f, volatile void *fifo, unsigne /* OUT */ {tu_fifo_get_write_info,tu_fifo_advance_write_pointer,pipe_read_packet}, /* IN */ {tu_fifo_get_read_info, tu_fifo_advance_read_pointer, pipe_write_packet}, }; + tu_fifo_buffer_info_t info; ops[dir].tu_fifo_get_info(f, &info); + unsigned total_len = len; len = TU_MIN(total_len, info.len_lin); ops[dir].pipe_read_write(info.ptr_lin, fifo, len); + unsigned rem = total_len - len; if (rem) { len = TU_MIN(rem, info.len_wrap); @@ -689,7 +691,8 @@ void dcd_init(uint8_t rhport) rusb2_module_start(rhport, true); - if ( is_highspeed(rhport) ) { +#ifdef RUSB2_SUPPORT_HIGHSPEED + if ( is_highspeed_usbip(rhport) ) { rusb->SYSCFG_b.HSE = 1; // leave CLKSEL as default (0x11) 24Mhz @@ -715,7 +718,9 @@ void dcd_init(uint8_t rhport) rusb->CFIFOSEL_b.MBW = 1; rusb->D0FIFOSEL_b.MBW = 1; rusb->D1FIFOSEL_b.MBW = 1; - } else { + } else +#endif + { rusb->SYSCFG_b.SCKE = 1; while (!rusb->SYSCFG_b.SCKE) {} rusb->SYSCFG_b.DRPD = 0; @@ -772,7 +777,7 @@ void dcd_connect(uint8_t rhport) { rusb2_reg_t* rusb = RUSB2_REG(rhport); - if ( is_highspeed(rhport)) { + if ( is_highspeed_usbip(rhport)) { rusb->SYSCFG_b.CNEN = 1; } rusb->SYSCFG_b.DPRPU = 1; @@ -809,7 +814,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) if (xfer == TUSB_XFER_ISOCHRONOUS) { // Fullspeed ISO is limit to 256 bytes - if ( !is_highspeed(rhport) && mps > 256) { + if ( !is_highspeed_usbip(rhport) && mps > 256) { return false; } } @@ -823,7 +828,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) /* setup pipe */ dcd_int_disable(rhport); - if ( is_highspeed(rhport) ) { + if ( is_highspeed_usbip(rhport) ) { // FIXME shouldn't be after pipe selection and config, also the BUFNMB should be changed // depending on the allocation scheme rusb->PIPEBUF = 0x7C08; diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 0dc59331a..e04a99685 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -62,7 +62,7 @@ typedef struct { }rusb2_controller_t; #if defined(BSP_MCU_GROUP_RA6M5) || defined(BSP_MCU_GROUP_RA6M3) || (BSP_CFG_MCU_PART_SERIES == 8) - #define RUSB2_HAS_HIGHSPEED + #define RUSB2_SUPPORT_HIGHSPEED #define RUSB2_CONTROLLER_COUNT 2 #else #define RUSB2_CONTROLLER_COUNT 1 @@ -71,7 +71,7 @@ typedef struct { // USBFS_INT_IRQn and USBHS_USB_INT_RESUME_IRQn are generated by FSP static rusb2_controller_t rusb2_controller[] = { { .reg_base = R_USB_FS0_BASE, .irqnum = USBFS_INT_IRQn }, - #ifdef RUSB2_HAS_HIGHSPEED + #ifdef RUSB2_SUPPORT_HIGHSPEED { .reg_base = R_USB_HS0_BASE, .irqnum = USBHS_USB_INT_RESUME_IRQn }, #endif }; diff --git a/src/portable/renesas/rusb2/rusb2_rx.h b/src/portable/renesas/rusb2/rusb2_rx.h index 21b2527c3..17b9a918c 100644 --- a/src/portable/renesas/rusb2/rusb2_rx.h +++ b/src/portable/renesas/rusb2/rusb2_rx.h @@ -37,7 +37,10 @@ extern "C" { #define RUSB2_REG_BASE (0x000A0000) -#define RUSB2_REG(_p) ((rusb2_reg_t *) RUSB2_REG_BASE) +TU_ATTR_ALWAYS_INLINE static inline rusb2_reg_t* RUSB2_REG(uint8_t rhport) { + (void) rhport; + return (rusb2_reg_t *) RUSB2_REG_BASE; +} // Start/Stop MSTP TODO implement later TU_ATTR_ALWAYS_INLINE static inline void rusb2_module_start(uint8_t rhport, bool start) { -- cgit v1.3.1 From 4c156100fafa682407f1a9a459d8b8800a029446 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 7 Jul 2023 12:27:18 +0700 Subject: use unaligned access read for hw fifo --- src/common/tusb_common.h | 18 ++++++-- src/common/tusb_mcu.h | 12 ++++-- src/portable/renesas/rusb2/dcd_rusb2.c | 77 +++++++++++++++++++++------------- 3 files changed, 71 insertions(+), 36 deletions(-) (limited to 'src/portable') diff --git a/src/common/tusb_common.h b/src/common/tusb_common.h index 957491aa9..576cb123f 100644 --- a/src/common/tusb_common.h +++ b/src/common/tusb_common.h @@ -260,11 +260,21 @@ TU_ATTR_ALWAYS_INLINE static inline void tu_unaligned_write16(void* mem, uint16_ #else // MCU that could access unaligned memory natively -TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_unaligned_read32 (const void* mem) { return *((uint32_t const *) mem); } -TU_ATTR_ALWAYS_INLINE static inline uint16_t tu_unaligned_read16 (const void* mem) { return *((uint16_t const *) mem); } +TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_unaligned_read32(const void *mem) { + return *((uint32_t const *) mem); +} + +TU_ATTR_ALWAYS_INLINE static inline uint16_t tu_unaligned_read16(const void *mem) { + return *((uint16_t const *) mem); +} -TU_ATTR_ALWAYS_INLINE static inline void tu_unaligned_write32 (void* mem, uint32_t value ) { *((uint32_t*) mem) = value; } -TU_ATTR_ALWAYS_INLINE static inline void tu_unaligned_write16 (void* mem, uint16_t value ) { *((uint16_t*) mem) = value; } +TU_ATTR_ALWAYS_INLINE static inline void tu_unaligned_write32(void *mem, uint32_t value) { + *((uint32_t *) mem) = value; +} + +TU_ATTR_ALWAYS_INLINE static inline void tu_unaligned_write16(void *mem, uint16_t value) { + *((uint16_t *) mem) = value; +} #endif diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 496ebfc85..89f89182e 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -34,10 +34,16 @@ //------------- Unaligned Memory Access -------------// -// ARMv7+ (M3-M7, M23-M33) can access unaligned memory -#if (defined(__ARM_ARCH) && (__ARM_ARCH >= 7)) - #define TUP_ARCH_STRICT_ALIGN 0 +#ifdef __ARM_ARCH + // ARM Architecture set __ARM_FEATURE_UNALIGNED to 1 for mcu supports unaligned access + #if defined(__ARM_FEATURE_UNALIGNED) && __ARM_FEATURE_UNALIGNED == 1 + #define TUP_ARCH_STRICT_ALIGN 0 + #else + #define TUP_ARCH_STRICT_ALIGN 1 + #endif #else + // TODO default to strict align for others + // Should investigate other architecture such as risv, xtensa, mips for optimal setting #define TUP_ARCH_STRICT_ALIGN 1 #endif diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 81b60b3bc..464929224 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -220,6 +220,11 @@ static inline void pipe_wait_for_ready(rusb2_reg_t * rusb, unsigned num) while ( !rusb->D0FIFOCTR_b.FRDY ) {} } +//--------------------------------------------------------------------+ +// Pipe FIFO +//--------------------------------------------------------------------+ + +// Write data buffer --> hw fifo static void pipe_write_packet(void *buf, volatile void *fifo, unsigned len) { #if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) @@ -228,54 +233,68 @@ static void pipe_write_packet(void *buf, volatile void *fifo, unsigned len) volatile hw_fifo16_t *reg = (volatile hw_fifo16_t*) fifo; #endif - uintptr_t addr = (uintptr_t)buf; + uint8_t const* buf8 = (uint8_t const*) buf; while (len >= 2) { - reg->u16 = *(const uint16_t *)addr; - addr += 2; + reg->u16 = tu_unaligned_read16(buf8); + buf8 += 2; len -= 2; } if (len > 0) { - reg->u8 = *(const uint8_t *)addr; - ++addr; + reg->u8 = *buf8; + ++buf8; } } +// Read data buffer <-- hw fifo static void pipe_read_packet(void *buf, volatile void *fifo, unsigned len) { - uint8_t *p = (uint8_t*)buf; + uint8_t *p = (uint8_t*)buf; volatile uint8_t *reg = (volatile uint8_t*)fifo; /* byte access is always at base register address */ while (len--) *p++ = *reg; } -static void pipe_read_write_packet_ff(tu_fifo_t *f, volatile void *fifo, unsigned len, unsigned dir) -{ - static const struct { - void (*tu_fifo_get_info)(tu_fifo_t *f, tu_fifo_buffer_info_t *info); - void (*tu_fifo_advance)(tu_fifo_t *f, uint16_t n); - void (*pipe_read_write)(void *buf, volatile void *fifo, unsigned len); - } ops[] = { - /* OUT */ {tu_fifo_get_write_info,tu_fifo_advance_write_pointer,pipe_read_packet}, - /* IN */ {tu_fifo_get_read_info, tu_fifo_advance_read_pointer, pipe_write_packet}, - }; +// Write data sw fifo --> hw fifo +static void pipe_write_packet_ff(tu_fifo_t *f, volatile void *fifo, uint16_t total_len) { + tu_fifo_buffer_info_t info; + tu_fifo_get_read_info(f, &info); + + uint16_t count = tu_min16(total_len, info.len_lin); + pipe_write_packet(info.ptr_lin, fifo, count); + + uint16_t rem = total_len - count; + if (rem) { + rem = tu_min16(rem, info.len_wrap); + pipe_write_packet(info.ptr_wrap, fifo, rem); + count += rem; + } + + tu_fifo_advance_read_pointer(f, count); +} +// Read data sw fifo <-- hw fifo +static void pipe_read_packet_ff(tu_fifo_t *f, volatile void *fifo, uint16_t total_len) { tu_fifo_buffer_info_t info; - ops[dir].tu_fifo_get_info(f, &info); + tu_fifo_get_write_info(f, &info); - unsigned total_len = len; - len = TU_MIN(total_len, info.len_lin); - ops[dir].pipe_read_write(info.ptr_lin, fifo, len); + uint16_t count = tu_min16(total_len, info.len_lin); + pipe_read_packet(info.ptr_lin, fifo, count); - unsigned rem = total_len - len; + uint16_t rem = total_len - count; if (rem) { - len = TU_MIN(rem, info.len_wrap); - ops[dir].pipe_read_write(info.ptr_wrap, fifo, len); - rem -= len; + rem = tu_min16(rem, info.len_wrap); + pipe_read_packet(info.ptr_wrap, fifo, rem); + count += rem; } - ops[dir].tu_fifo_advance(f, total_len - rem); + + tu_fifo_advance_write_pointer(f, count); } +//--------------------------------------------------------------------+ +// Pipe Transfer +//--------------------------------------------------------------------+ + static bool pipe0_xfer_in(rusb2_reg_t* rusb) { pipe_state_t *pipe = &_dcd.pipe[0]; @@ -292,7 +311,7 @@ static bool pipe0_xfer_in(rusb2_reg_t* rusb) if (len) { if (pipe->ff) { - pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len, TUSB_DIR_IN); + pipe_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len); } else { pipe_write_packet(buf, (volatile void*)&rusb->CFIFO, len); pipe->buf = (uint8_t*)buf + len; @@ -319,7 +338,7 @@ static bool pipe0_xfer_out(rusb2_reg_t* rusb) if (len) { if (pipe->ff) { - pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len, TUSB_DIR_OUT); + pipe_read_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len); } else { pipe_read_packet(buf, (volatile void*)&rusb->CFIFO, len); pipe->buf = (uint8_t*)buf + len; @@ -357,7 +376,7 @@ static bool pipe_xfer_in(rusb2_reg_t* rusb, unsigned num) if (len) { if (pipe->ff) { - pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len, TUSB_DIR_IN); + pipe_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len); } else { pipe_write_packet(buf, (volatile void*)&rusb->D0FIFO, len); pipe->buf = (uint8_t*)buf + len; @@ -391,7 +410,7 @@ static bool pipe_xfer_out(rusb2_reg_t* rusb, unsigned num) if (len) { if (pipe->ff) { - pipe_read_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len, TUSB_DIR_OUT); + pipe_read_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len); } else { pipe_read_packet(buf, (volatile void*)&rusb->D0FIFO, len); pipe->buf = (uint8_t*)buf + len; -- cgit v1.3.1 From e0f1ba8b0e9cf46fabcddc72a61d5515df424edf Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 7 Jul 2023 16:07:11 +0700 Subject: fully work with multiple ports without CFG_TUSB_RHPORT0/1 --- hw/bsp/family_support.cmake | 4 +- hw/bsp/ra/boards/ra6m5_ek/board.cmake | 7 --- src/portable/renesas/rusb2/dcd_rusb2.c | 85 ++++++++++++++------------------- src/portable/renesas/rusb2/rusb2_type.h | 1 + 4 files changed, 39 insertions(+), 58 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index 5b97eb5e4..d8298c8ad 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -227,8 +227,8 @@ function(family_add_tinyusb TARGET OPT_MCU RTOS) if (DEFINED LOG) target_compile_definitions(${TARGET}-tinyusb_config INTERFACE CFG_TUSB_DEBUG=${LOG}) - if (LOG STREQUAL "3") - # no inline for debug level 3 + if (LOG STREQUAL "4") + # no inline for debug level 4 target_compile_definitions(${TARGET}-tinyusb_config INTERFACE TU_ATTR_ALWAYS_INLINE=) endif () endif() diff --git a/hw/bsp/ra/boards/ra6m5_ek/board.cmake b/hw/bsp/ra/boards/ra6m5_ek/board.cmake index d934a0c0d..5a615f9b0 100644 --- a/hw/bsp/ra/boards/ra6m5_ek/board.cmake +++ b/hw/bsp/ra/boards/ra6m5_ek/board.cmake @@ -14,11 +14,4 @@ function(update_board TARGET) # port 0 is fullspeed, port 1 is highspeed BOARD_TUD_MAX_SPEED=$ ) - - if (PORT STREQUAL 1) - target_compile_definitions(${TARGET} PUBLIC - CFG_TUSB_RHPORT1_MODE=OPT_MODE_DEVICE|OPT_MODE_HIGH_SPEED - CFG_TUSB_RHPORT0_MODE=0 - ) - endif () endfunction() diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 464929224..3d3e52bfa 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -74,26 +74,6 @@ typedef struct TU_ATTR_PACKED _ccrx_evenaccess { uint16_t TRN; } reg_pipetre_t; -typedef union TU_ATTR_PACKED { - struct { - volatile uint8_t u8; - volatile uint8_t reserved8; - }; - volatile uint16_t u16; -} hw_fifo16_t; - -typedef union TU_ATTR_PACKED { - struct { - volatile uint8_t reserved8[3]; - volatile uint8_t u8; - }; - struct { - volatile uint16_t reserved16; - volatile uint16_t u16; - }; - volatile uint32_t u32; -} hw_fifo32_t; - typedef struct TU_ATTR_PACKED { void *buf; /* the start address of a transfer data buffer */ @@ -135,9 +115,11 @@ static dcd_data_t _dcd; //--------------------------------------------------------------------+ #ifdef RUSB2_SUPPORT_HIGHSPEED - #define is_highspeed_usbip(_p) (_p == 1) + #define is_highspeed_usbip(_p) (_p == 1) + #define is_highspeed_regbase(_reg) (_reg == RUSB2_REG(1)) #else - #define is_highspeed_usbip(_p) (false) + #define is_highspeed_usbip(_p) (false) + #define is_highspeed_regbase(_reg) (false) #endif static unsigned find_pipe(unsigned xfer) @@ -225,48 +207,57 @@ static inline void pipe_wait_for_ready(rusb2_reg_t * rusb, unsigned num) //--------------------------------------------------------------------+ // Write data buffer --> hw fifo -static void pipe_write_packet(void *buf, volatile void *fifo, unsigned len) +static void pipe_write_packet(rusb2_reg_t * rusb, void *buf, volatile void *fifo, unsigned len) { -#if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_DEVICE) - volatile hw_fifo32_t *reg = (volatile hw_fifo32_t*) fifo; -#else - volatile hw_fifo16_t *reg = (volatile hw_fifo16_t*) fifo; -#endif + (void) rusb; + + volatile uint16_t *ff16; + volatile uint8_t *ff8; + + // Highspeed FIFO is 32-bit + if ( is_highspeed_regbase(rusb) ) { + ff16 = (volatile uint16_t*) ((uintptr_t) fifo+2); + ff8 = (volatile uint8_t *) ((uintptr_t) fifo+3); + }else { + ff16 = (volatile uint16_t*) fifo; + ff8 = ((volatile uint8_t*) fifo); + } uint8_t const* buf8 = (uint8_t const*) buf; while (len >= 2) { - reg->u16 = tu_unaligned_read16(buf8); + *ff16 = tu_unaligned_read16(buf8); buf8 += 2; len -= 2; } if (len > 0) { - reg->u8 = *buf8; + *ff8 = *buf8; ++buf8; } } // Read data buffer <-- hw fifo -static void pipe_read_packet(void *buf, volatile void *fifo, unsigned len) +static void pipe_read_packet(rusb2_reg_t * rusb, void *buf, volatile void *fifo, unsigned len) { + (void) rusb; uint8_t *p = (uint8_t*)buf; volatile uint8_t *reg = (volatile uint8_t*)fifo; /* byte access is always at base register address */ while (len--) *p++ = *reg; } // Write data sw fifo --> hw fifo -static void pipe_write_packet_ff(tu_fifo_t *f, volatile void *fifo, uint16_t total_len) { +static void pipe_write_packet_ff(rusb2_reg_t * rusb, tu_fifo_t *f, volatile void *fifo, uint16_t total_len) { tu_fifo_buffer_info_t info; tu_fifo_get_read_info(f, &info); uint16_t count = tu_min16(total_len, info.len_lin); - pipe_write_packet(info.ptr_lin, fifo, count); + pipe_write_packet(rusb, info.ptr_lin, fifo, count); uint16_t rem = total_len - count; if (rem) { rem = tu_min16(rem, info.len_wrap); - pipe_write_packet(info.ptr_wrap, fifo, rem); + pipe_write_packet(rusb, info.ptr_wrap, fifo, rem); count += rem; } @@ -274,17 +265,17 @@ static void pipe_write_packet_ff(tu_fifo_t *f, volatile void *fifo, uint16_t tot } // Read data sw fifo <-- hw fifo -static void pipe_read_packet_ff(tu_fifo_t *f, volatile void *fifo, uint16_t total_len) { +static void pipe_read_packet_ff(rusb2_reg_t * rusb, tu_fifo_t *f, volatile void *fifo, uint16_t total_len) { tu_fifo_buffer_info_t info; tu_fifo_get_write_info(f, &info); uint16_t count = tu_min16(total_len, info.len_lin); - pipe_read_packet(info.ptr_lin, fifo, count); + pipe_read_packet(rusb, info.ptr_lin, fifo, count); uint16_t rem = total_len - count; if (rem) { rem = tu_min16(rem, info.len_wrap); - pipe_read_packet(info.ptr_wrap, fifo, rem); + pipe_read_packet(rusb, info.ptr_wrap, fifo, rem); count += rem; } @@ -311,9 +302,9 @@ static bool pipe0_xfer_in(rusb2_reg_t* rusb) if (len) { if (pipe->ff) { - pipe_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len); + pipe_write_packet_ff(rusb, (tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len); } else { - pipe_write_packet(buf, (volatile void*)&rusb->CFIFO, len); + pipe_write_packet(rusb, buf, (volatile void*)&rusb->CFIFO, len); pipe->buf = (uint8_t*)buf + len; } } @@ -338,9 +329,9 @@ static bool pipe0_xfer_out(rusb2_reg_t* rusb) if (len) { if (pipe->ff) { - pipe_read_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len); + pipe_read_packet_ff(rusb, (tu_fifo_t*)buf, (volatile void*)&rusb->CFIFO, len); } else { - pipe_read_packet(buf, (volatile void*)&rusb->CFIFO, len); + pipe_read_packet(rusb, buf, (volatile void*)&rusb->CFIFO, len); pipe->buf = (uint8_t*)buf + len; } } @@ -376,9 +367,9 @@ static bool pipe_xfer_in(rusb2_reg_t* rusb, unsigned num) if (len) { if (pipe->ff) { - pipe_write_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len); + pipe_write_packet_ff(rusb, (tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len); } else { - pipe_write_packet(buf, (volatile void*)&rusb->D0FIFO, len); + pipe_write_packet(rusb, buf, (volatile void*)&rusb->D0FIFO, len); pipe->buf = (uint8_t*)buf + len; } } @@ -410,9 +401,9 @@ static bool pipe_xfer_out(rusb2_reg_t* rusb, unsigned num) if (len) { if (pipe->ff) { - pipe_read_packet_ff((tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len); + pipe_read_packet_ff(rusb, (tu_fifo_t*)buf, (volatile void*)&rusb->D0FIFO, len); } else { - pipe_read_packet(buf, (volatile void*)&rusb->D0FIFO, len); + pipe_read_packet(rusb, buf, (volatile void*)&rusb->D0FIFO, len); pipe->buf = (uint8_t*)buf + len; } } @@ -733,10 +724,6 @@ void dcd_init(uint8_t rhport) // rusb2->BUSWAIT |= 0x0F00U; rusb->PHYSET_b.REPSEL = 1; - - rusb->CFIFOSEL_b.MBW = 1; - rusb->D0FIFOSEL_b.MBW = 1; - rusb->D1FIFOSEL_b.MBW = 1; } else #endif { diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index 7a5e37089..28cec9999 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -1670,6 +1670,7 @@ TU_ATTR_BIT_FIELD_ORDER_END #define RUSB2_FIFOSEL_BIGEND (1U << RUSB2_CFIFOSEL_BIGEND_Pos) /* FIFO Big Endian */ #define RUSB2_FIFOSEL_MBW_8BIT (0U << RUSB2_CFIFOSEL_MBW_Pos) /* 8-bit width */ #define RUSB2_FIFOSEL_MBW_16BIT (1U << RUSB2_CFIFOSEL_MBW_Pos) /* 16-bit width */ +#define RUSB2_FIFOSEL_MBW_32BIT (2U << RUSB2_CFIFOSEL_MBW_Pos) /* 32-bit width */ #define RUSB2_INTSTS0_CTSQ_CTRL_RDATA (1U << RUSB2_INTSTS0_CTSQ_Pos) -- cgit v1.3.1 From 88478a9d052edc364561da39382faef72f937ecb Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 7 Jul 2023 16:24:22 +0700 Subject: add PORT selection for makefile --- hw/bsp/ra/boards/ra6m5_ek/board.mk | 3 +++ hw/bsp/ra/family.cmake | 2 +- hw/bsp/ra/family.mk | 12 ++++++++++++ src/portable/renesas/rusb2/dcd_rusb2.c | 4 ++++ 4 files changed, 20 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/hw/bsp/ra/boards/ra6m5_ek/board.mk b/hw/bsp/ra/boards/ra6m5_ek/board.mk index 567908b63..a5c933764 100644 --- a/hw/bsp/ra/boards/ra6m5_ek/board.mk +++ b/hw/bsp/ra/boards/ra6m5_ek/board.mk @@ -4,4 +4,7 @@ MCU_VARIANT = ra6m5 # For flash-jlink target JLINK_DEVICE = R7FA6M5BH +# Port 1 is highspeed +PORT ?= 1 + flash: flash-jlink diff --git a/hw/bsp/ra/family.cmake b/hw/bsp/ra/family.cmake index eb2d4958f..f09e86a72 100644 --- a/hw/bsp/ra/family.cmake +++ b/hw/bsp/ra/family.cmake @@ -13,7 +13,7 @@ include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) set(CMAKE_TOOLCHAIN_FILE ${TOP}/tools/cmake/toolchain/arm_${TOOLCHAIN}.cmake) -set(FAMILY_MCUS RA CACHE INTERNAL "") +set(FAMILY_MCUS RAXXX CACHE INTERNAL "") #------------------------------------ # BOARD_TARGET diff --git a/hw/bsp/ra/family.mk b/hw/bsp/ra/family.mk index b6e1bb0ae..f5097460a 100644 --- a/hw/bsp/ra/family.mk +++ b/hw/bsp/ra/family.mk @@ -3,8 +3,12 @@ DEPS_SUBMODULES += hw/mcu/renesas/fsp lib/CMSIS_5 FSP_RA = hw/mcu/renesas/fsp/ra/fsp include $(TOP)/$(BOARD_PATH)/board.mk +# Default to port 0 fullspeed, board with port 1 highspeed should override this in board.mk +PORT ?= 0 + CFLAGS += \ -DCFG_TUSB_MCU=OPT_MCU_RAXXX \ + -DBOARD_TUD_RHPORT=$(PORT) \ -Wno-error=undef \ -Wno-error=strict-prototypes \ -Wno-error=cast-align \ @@ -15,6 +19,14 @@ CFLAGS += \ -nostartfiles \ -ffreestanding +ifeq ($(PORT), 1) + CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED + $(info "Using PORT 1 HighSpeed") +else + CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED + $(info "Using PORT 0 FullSpeed") +endif + SRC_C += \ src/portable/renesas/rusb2/dcd_rusb2.c \ src/portable/renesas/rusb2/hcd_rusb2.c \ diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 3d3e52bfa..17d22f696 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -216,6 +216,7 @@ static void pipe_write_packet(rusb2_reg_t * rusb, void *buf, volatile void *fifo // Highspeed FIFO is 32-bit if ( is_highspeed_regbase(rusb) ) { + // TODO 32-bit access for better performance ff16 = (volatile uint16_t*) ((uintptr_t) fifo+2); ff8 = (volatile uint8_t *) ((uintptr_t) fifo+3); }else { @@ -241,6 +242,9 @@ static void pipe_write_packet(rusb2_reg_t * rusb, void *buf, volatile void *fifo static void pipe_read_packet(rusb2_reg_t * rusb, void *buf, volatile void *fifo, unsigned len) { (void) rusb; + + // TODO 16/32-bit access for better performance + uint8_t *p = (uint8_t*)buf; volatile uint8_t *reg = (volatile uint8_t*)fifo; /* byte access is always at base register address */ while (len--) *p++ = *reg; -- cgit v1.3.1 From 0f53e746ffa21b6186809b2b896ddc74d38e9058 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 7 Jul 2023 18:41:16 +0700 Subject: move check highspeed to rusb_ra --- src/portable/renesas/rusb2/dcd_rusb2.c | 31 +++++-------------------------- src/portable/renesas/rusb2/rusb2_ra.h | 15 +++++++++++---- src/portable/renesas/rusb2/rusb2_rx.h | 9 +++++++++ src/portable/renesas/rusb2/rusb2_type.h | 14 ++++++++++++++ 4 files changed, 39 insertions(+), 30 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 17d22f696..358e5644b 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -61,19 +61,6 @@ TU_ATTR_PACKED_BEGIN TU_ATTR_BIT_FIELD_ORDER_BEGIN -typedef struct TU_ATTR_PACKED _ccrx_evenaccess { - union { - struct { - uint16_t : 8; - uint16_t TRCLR: 1; - uint16_t TRENB: 1; - uint16_t : 0; - }; - uint16_t TRE; - }; - uint16_t TRN; -} reg_pipetre_t; - typedef struct TU_ATTR_PACKED { void *buf; /* the start address of a transfer data buffer */ @@ -114,14 +101,6 @@ static dcd_data_t _dcd; // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -#ifdef RUSB2_SUPPORT_HIGHSPEED - #define is_highspeed_usbip(_p) (_p == 1) - #define is_highspeed_regbase(_reg) (_reg == RUSB2_REG(1)) -#else - #define is_highspeed_usbip(_p) (false) - #define is_highspeed_regbase(_reg) (false) -#endif - static unsigned find_pipe(unsigned xfer) { switch (xfer) { @@ -215,7 +194,7 @@ static void pipe_write_packet(rusb2_reg_t * rusb, void *buf, volatile void *fifo volatile uint8_t *ff8; // Highspeed FIFO is 32-bit - if ( is_highspeed_regbase(rusb) ) { + if ( rusb2_is_highspeed_reg(rusb) ) { // TODO 32-bit access for better performance ff16 = (volatile uint16_t*) ((uintptr_t) fifo+2); ff8 = (volatile uint8_t *) ((uintptr_t) fifo+3); @@ -706,7 +685,7 @@ void dcd_init(uint8_t rhport) rusb2_module_start(rhport, true); #ifdef RUSB2_SUPPORT_HIGHSPEED - if ( is_highspeed_usbip(rhport) ) { + if ( rusb2_is_highspeed_rhport(rhport) ) { rusb->SYSCFG_b.HSE = 1; // leave CLKSEL as default (0x11) 24Mhz @@ -787,7 +766,7 @@ void dcd_connect(uint8_t rhport) { rusb2_reg_t* rusb = RUSB2_REG(rhport); - if ( is_highspeed_usbip(rhport)) { + if ( rusb2_is_highspeed_rhport(rhport)) { rusb->SYSCFG_b.CNEN = 1; } rusb->SYSCFG_b.DPRPU = 1; @@ -824,7 +803,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) if (xfer == TUSB_XFER_ISOCHRONOUS) { // Fullspeed ISO is limit to 256 bytes - if ( !is_highspeed_usbip(rhport) && mps > 256) { + if ( !rusb2_is_highspeed_rhport(rhport) && mps > 256) { return false; } } @@ -838,7 +817,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) /* setup pipe */ dcd_int_disable(rhport); - if ( is_highspeed_usbip(rhport) ) { + if ( rusb2_is_highspeed_rhport(rhport) ) { // FIXME shouldn't be after pipe selection and config, also the BUFNMB should be changed // depending on the allocation scheme rusb->PIPEBUF = 0x7C08; diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index e04a99685..28b690512 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -47,15 +47,15 @@ extern "C" { #pragma GCC diagnostic pop #endif -//--------------------------------------------------------------------+ -// -//--------------------------------------------------------------------+ - // IAR does not have __builtin_ctz #if defined(__ICCARM__) #define __builtin_ctz(x) __iar_builtin_CLZ(__iar_builtin_RBIT(x)) #endif +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + typedef struct { uint32_t reg_base; int32_t irqnum; @@ -78,6 +78,13 @@ static rusb2_controller_t rusb2_controller[] = { #define RUSB2_REG(_p) ((rusb2_reg_t*) rusb2_controller[_p].reg_base) +#define rusb2_is_highspeed_rhport(_p) (_p == 1) +#define rusb2_is_highspeed_reg(_reg) (_reg == RUSB2_REG(1)) + +//--------------------------------------------------------------------+ +// RUSB2 API +//--------------------------------------------------------------------+ + TU_ATTR_ALWAYS_INLINE static inline void rusb2_module_start(uint8_t rhport, bool start) { uint32_t const mask = 1U << (11+rhport); if (start) { diff --git a/src/portable/renesas/rusb2/rusb2_rx.h b/src/portable/renesas/rusb2/rusb2_rx.h index 17b9a918c..7bf4be47e 100644 --- a/src/portable/renesas/rusb2/rusb2_rx.h +++ b/src/portable/renesas/rusb2/rusb2_rx.h @@ -42,6 +42,15 @@ TU_ATTR_ALWAYS_INLINE static inline rusb2_reg_t* RUSB2_REG(uint8_t rhport) { return (rusb2_reg_t *) RUSB2_REG_BASE; } + +#define rusb2_is_highspeed_rhport(_p) (false) +#define rusb2_is_highspeed_reg(_reg) (false) + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + + // Start/Stop MSTP TODO implement later TU_ATTR_ALWAYS_INLINE static inline void rusb2_module_start(uint8_t rhport, bool start) { (void) rhport; diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index 28cec9999..aceeb3c3e 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -48,6 +48,20 @@ extern "C" { TU_ATTR_PACKED_BEGIN TU_ATTR_BIT_FIELD_ORDER_BEGIN +// TODO same as RUSB2_PIPE_TR_t +typedef struct TU_ATTR_PACKED _ccrx_evenaccess { + union { + struct { + uint16_t : 8; + uint16_t TRCLR: 1; + uint16_t TRENB: 1; + uint16_t : 0; + }; + uint16_t TRE; + }; + uint16_t TRN; +} reg_pipetre_t; + typedef struct { union { volatile uint16_t E; /* (@ 0x00000000) Pipe Transaction Counter Enable Register */ -- cgit v1.3.1 From 8b6d0a166b3837e664eeabbada724b678b7fd62d Mon Sep 17 00:00:00 2001 From: Scott Shawcroft Date: Fri, 14 Jul 2023 15:30:22 -0700 Subject: Fix host buffer alignment setting --- src/portable/chipidea/ci_hs/ci_hs_imxrt.h | 6 ++++++ src/tusb_option.h | 6 +++++- 2 files changed, 11 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h index c14f00431..96f0ba766 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h +++ b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h @@ -78,6 +78,12 @@ TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_clean(void const* addr, ui TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_invalidate(void const* addr, uint32_t data_size) { const uintptr_t addr32 = (uintptr_t) addr; if (imxrt_is_cache_mem(addr32)) { + // Invalidating does not push cached changes back to RAM so we need to be + // *very* careful when we do it. If we're not aligned, then we risk resetting + // values back to their RAM state. + // if (addr32 % 32 != 0) { + // TU_BREAKPOINT(); + // } SCB_InvalidateDCache_by_Addr((void*) addr32, (int32_t) data_size); } } diff --git a/src/tusb_option.h b/src/tusb_option.h index f16d8a5d0..c792efe6a 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -431,7 +431,11 @@ // Attribute to align memory for host controller #ifndef CFG_TUH_MEM_ALIGN - #define CFG_TUH_MEM_ALIGN TU_ATTR_ALIGNED(4) + #ifdef CFG_TUSB_MEM_ALIGN + #define CFG_TUH_MEM_ALIGN CFG_TUSB_MEM_ALIGN + #else + #define CFG_TUH_MEM_ALIGN TU_ATTR_ALIGNED(4) + #endif #endif //------------- CLASS -------------// -- cgit v1.3.1 From 1923b1845d033a3d42db9b739029b2cc39248150 Mon Sep 17 00:00:00 2001 From: Aladdin Bakosh Date: Fri, 23 Jun 2023 10:26:45 +0200 Subject: fix(RA_hcd): STALL status can be also 3 not only 2 --- src/host/usbh.c | 2 +- src/portable/renesas/rusb2/hcd_rusb2.c | 5 +++-- src/portable/renesas/rusb2/rusb2_type.h | 1 + 3 files changed, 5 insertions(+), 3 deletions(-) (limited to 'src/portable') diff --git a/src/host/usbh.c b/src/host/usbh.c index f3e9d3858..184bda23b 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -791,7 +791,7 @@ bool usbh_edpt_xfer_with_callback(uint8_t dev_addr, uint8_t ep_addr, uint8_t * b uint8_t const dir = tu_edpt_dir(ep_addr); tu_edpt_state_t* ep_state = &dev->ep_status[epnum][dir]; - TU_LOG_USBH(" Queue EP %02X with %u bytes ... ", ep_addr, total_bytes); + TU_LOG_USBH(" Queue EP %02X with %u bytes ... \r\n", ep_addr, total_bytes); // Attempt to transfer on a busy endpoint, sound like an race condition ! TU_ASSERT(ep_state->busy == 0); diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 0e6fa1618..193e07d8c 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -116,7 +116,7 @@ static unsigned find_pipe(unsigned xfer) for (int i = 3; i <= 5; ++i) { if (0 == _hcd.pipe[i].ep) return i; } - for (int i = 1; i <= 1; ++i) { + for (int i = 1; i <= 2; ++i) { if (0 == _hcd.pipe[i].ep) return i; } break; @@ -413,6 +413,7 @@ static void process_pipe_nrdy(uint8_t rhport, unsigned num) switch (*ctr & RUSB2_PIPE_CTR_PID_Msk) { default: return; case RUSB2_PIPE_CTR_PID_STALL: result = XFER_RESULT_STALLED; break; + case RUSB2_PIPE_CTR_PID_STALL2: result = XFER_RESULT_STALLED; break; case RUSB2_PIPE_CTR_PID_NAK: result = XFER_RESULT_FAILED; break; } pipe_state_t *pipe = &_hcd.pipe[num]; @@ -586,7 +587,7 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) uint8_t *ep = &_hcd.ep[dev_addr - 1][0][0]; for (int i = 0; i < 2 * 15; ++i, ++ep) { unsigned num = *ep; - if (!num || dev_addr != _hcd.pipe[num].dev) continue; + if (!num || (dev_addr != _hcd.pipe[num].dev)) continue; ctr = (uint16_t volatile*)&RUSB2->PIPE_CTR[num - 1]; *ctr = 0; diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index 90ba4f012..83119507a 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -1568,6 +1568,7 @@ TU_ATTR_BIT_FIELD_ORDER_END #define RUSB2_PIPE_CTR_PID_NAK (0U << RUSB2_PIPE_CTR_PID_Pos) /* NAK response */ #define RUSB2_PIPE_CTR_PID_BUF (1U << RUSB2_PIPE_CTR_PID_Pos) /* BUF response (depends buffer state) */ #define RUSB2_PIPE_CTR_PID_STALL (2U << RUSB2_PIPE_CTR_PID_Pos) /* STALL response */ +#define RUSB2_PIPE_CTR_PID_STALL2 (3U << RUSB2_PIPE_CTR_PID_Pos) /* Also STALL response */ #define RUSB2_DVSTCTR0_RHST_LS (1U << RUSB2_DVSTCTR0_RHST_Pos) /* Low-speed connection */ #define RUSB2_DVSTCTR0_RHST_FS (2U << RUSB2_DVSTCTR0_RHST_Pos) /* Full-speed connection */ -- cgit v1.3.1 From 41b608562a40b68d6b58d01a3239c466533b4b6b Mon Sep 17 00:00:00 2001 From: Aladdin Bakosh Date: Fri, 23 Jun 2023 14:21:58 +0200 Subject: debugging can be configured on renesas hcd --- src/portable/renesas/rusb2/hcd_rusb2.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 193e07d8c..65bbc656b 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -41,6 +41,8 @@ #error "Unsupported MCU" #endif +#define TU_RUSB2_HCD_DBG 0 + //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM DECLARATION //--------------------------------------------------------------------+ @@ -409,7 +411,7 @@ static void process_pipe_nrdy(uint8_t rhport, unsigned num) (void)rhport; xfer_result_t result; uint16_t volatile *ctr = get_pipectr(num); - // TU_LOG1("NRDY %d %x\n", num, *ctr); + TU_LOG(TU_RUSB2_HCD_DBG, "NRDY %d %x\n", num, *ctr); switch (*ctr & RUSB2_PIPE_CTR_PID_Msk) { default: return; case RUSB2_PIPE_CTR_PID_STALL: result = XFER_RESULT_STALLED; break; @@ -442,7 +444,7 @@ static void process_pipe_brdy(uint8_t rhport, unsigned num) hcd_event_xfer_complete(pipe->dev, pipe->ep, pipe->length - pipe->remaining, XFER_RESULT_SUCCESS, true); - // TU_LOG1("C %d %d\r\n", num, pipe->length - pipe->remaining); + TU_LOG(TU_RUSB2_HCD_DBG, "C %d %d\r\n", num, pipe->length - pipe->remaining); } } @@ -609,7 +611,7 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { (void)rhport; - // TU_LOG1("S %d %x\n", dev_addr, RUSB2->DCPCTR); + TU_LOG(TU_RUSB2_HCD_DBG, "S %d %x\n", dev_addr, RUSB2->DCPCTR); TU_ASSERT(dev_addr < 6); /* USBa can only handle addresses from 0 to 5. */ TU_ASSERT(0 == RUSB2->DCPCTR_b.SUREQ); @@ -702,7 +704,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t *b { bool r; hcd_int_disable(rhport); - // TU_LOG1("X %d %x %u\n", dev_addr, ep_addr, buflen); + TU_LOG(TU_RUSB2_HCD_DBG, "X %d %x %u\n", dev_addr, ep_addr, buflen); r = process_edpt_xfer(dev_addr, ep_addr, buffer, buflen); hcd_int_enable(rhport); return r; @@ -746,7 +748,7 @@ void hcd_int_handler(uint8_t rhport) /* clear active bits except VALID (don't write 0 to already cleared bits according to the HW manual) */ RUSB2->INTSTS1 = ~((RUSB2_INTSTS1_SACK_Msk | RUSB2_INTSTS1_SIGN_Msk | RUSB2_INTSTS1_ATTCH_Msk | RUSB2_INTSTS1_DTCH_Msk) & is1); RUSB2->INTSTS0 = ~((RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_NRDY_Msk | RUSB2_INTSTS0_BEMP_Msk) & is0); - // TU_LOG1("IS %04x %04x\n", is0, is1); + TU_LOG(TU_RUSB2_HCD_DBG, "IS %04x %04x\n", is0, is1); is1 &= RUSB2->INTENB1; is0 &= RUSB2->INTENB0; -- cgit v1.3.1 From 3230d5b1ea45ac2b17e4abaac2bfbe190360fff8 Mon Sep 17 00:00:00 2001 From: Aladdin Bakosh Date: Fri, 23 Jun 2023 14:22:13 +0200 Subject: debugging can be configured on renesas dcd --- src/portable/renesas/rusb2/dcd_rusb2.c | 8 +++++--- 1 file changed, 5 insertions(+), 3 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 78584125f..022c1b5b6 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -45,6 +45,8 @@ #error "Unsupported MCU" #endif +#define TU_RUSB2_DCD_DBG 0 + //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM //--------------------------------------------------------------------+ @@ -444,7 +446,7 @@ static bool process_pipe_xfer(int buffer_type, uint8_t ep_addr, void* buffer, ui *ctr = RUSB2_PIPE_CTR_PID_BUF; } } - // TU_LOG1("X %x %d %d\r\n", ep_addr, total_bytes, buffer_type); + TU_LOG(TU_RUSB2_DCD_DBG ,"X %x %d %d\r\n", ep_addr, total_bytes, buffer_type); return true; } @@ -487,7 +489,7 @@ static void process_pipe_brdy(uint8_t rhport, unsigned num) dcd_event_xfer_complete(rhport, pipe->ep, pipe->length - pipe->remaining, XFER_RESULT_SUCCESS, true); - // TU_LOG1("C %d %d\r\n", num, pipe->length - pipe->remaining); + TU_LOG(TU_RUSB2_DCD_DBG, "C %d %d\r\n", num, pipe->length - pipe->remaining); } } @@ -691,7 +693,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) if (dir || (xfer != TUSB_XFER_BULK)) { *ctr = RUSB2_PIPE_CTR_PID_BUF; } - // TU_LOG1("O %d %x %x\r\n", RUSB2->PIPESEL, RUSB2->PIPECFG, RUSB2->PIPEMAXP); + TU_LOG(TU_RUSB2_DCD_DBG, "O %d %x %x\r\n", RUSB2->PIPESEL, RUSB2->PIPECFG, RUSB2->PIPEMAXP); dcd_int_enable(rhport); return true; -- cgit v1.3.1 From 1cc7c5d0309bcc7c6930fba78bc461e5822e8024 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 20 Jul 2023 11:20:12 +0700 Subject: add hcd_edpt_abort_xfer() API --- examples/dual/host_hid_to_device_cdc/only.txt | 1 + src/host/hcd.h | 3 +++ src/host/usbh.c | 28 +++++++++++++++++++-------- src/host/usbh.h | 7 +++++-- src/portable/ehci/ehci.c | 18 +++++++++++++++++ 5 files changed, 47 insertions(+), 10 deletions(-) (limited to 'src/portable') diff --git a/examples/dual/host_hid_to_device_cdc/only.txt b/examples/dual/host_hid_to_device_cdc/only.txt index 6ee8e3fde..de5d8bed9 100644 --- a/examples/dual/host_hid_to_device_cdc/only.txt +++ b/examples/dual/host_hid_to_device_cdc/only.txt @@ -1,3 +1,4 @@ board:mimxrt1060_evk board:mimxrt1064_evk +board:mcb1800 mcu:RP2040 diff --git a/src/host/hcd.h b/src/host/hcd.h index 3355c18b2..cbfffb349 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -171,6 +171,9 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const // Submit a transfer, when complete hcd_event_xfer_complete() must be invoked bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen); +// Abort a queued transfer. Note: it can only abort transfer that has not been started +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr); + // Submit a special transfer to send 8-byte Setup Packet, when complete hcd_event_xfer_complete() must be invoked bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]); diff --git a/src/host/usbh.c b/src/host/usbh.c index ecc672198..bbf333d5f 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -710,6 +710,19 @@ bool tuh_edpt_xfer(tuh_xfer_t* xfer) return true; } +bool tuh_edpt_abort_xfer(uint8_t daddr, uint8_t ep_addr) { + usbh_device_t* dev = get_device(daddr); + TU_VERIFY(dev); + + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); + + // skip if not busy + if (!dev->ep_status[epnum][dir].busy) return true; + + return hcd_edpt_abort_xfer(dev->rhport, daddr, ep_addr); +} + //--------------------------------------------------------------------+ // USBH API For Class Driver //--------------------------------------------------------------------+ @@ -741,7 +754,7 @@ void usbh_int_set(bool enabled) // Endpoint API //--------------------------------------------------------------------+ -// TODO has some duplication code with device, refactor later +// Claim an endpoint for transfer bool usbh_edpt_claim(uint8_t dev_addr, uint8_t ep_addr) { // Note: addr0 only use tuh_control_xfer @@ -757,7 +770,7 @@ bool usbh_edpt_claim(uint8_t dev_addr, uint8_t ep_addr) return true; } -// TODO has some duplication code with device, refactor later +// Release an claimed endpoint due to failed transfer attempt bool usbh_edpt_release(uint8_t dev_addr, uint8_t ep_addr) { // Note: addr0 only use tuh_control_xfer @@ -773,7 +786,7 @@ bool usbh_edpt_release(uint8_t dev_addr, uint8_t ep_addr) return true; } -// TODO has some duplication code with device, refactor later +// Submit an transfer bool usbh_edpt_xfer_with_callback(uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { @@ -840,14 +853,13 @@ bool tuh_edpt_open(uint8_t dev_addr, tusb_desc_endpoint_t const * desc_ep) return hcd_edpt_open(usbh_get_rhport(dev_addr), dev_addr, desc_ep); } -bool usbh_edpt_busy(uint8_t dev_addr, uint8_t ep_addr) -{ - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - +bool usbh_edpt_busy(uint8_t dev_addr, uint8_t ep_addr) { usbh_device_t* dev = get_device(dev_addr); TU_VERIFY(dev); + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); + return dev->ep_status[epnum][dir].busy; } diff --git a/src/host/usbh.h b/src/host/usbh.h index 0f969a46a..d765f6744 100644 --- a/src/host/usbh.h +++ b/src/host/usbh.h @@ -172,8 +172,11 @@ bool tuh_control_xfer(tuh_xfer_t* xfer); // - sync : blocking if complete callback is NULL. bool tuh_edpt_xfer(tuh_xfer_t* xfer); -// Open an non-control endpoint -bool tuh_edpt_open(uint8_t dev_addr, tusb_desc_endpoint_t const * desc_ep); +// Open a non-control endpoint +bool tuh_edpt_open(uint8_t daddr, tusb_desc_endpoint_t const * desc_ep); + +// Abort a queued transfer. Note: it can only abort transfer that has not been started +bool tuh_edpt_abort_xfer(uint8_t daddr, uint8_t ep_addr); // Set Configuration (control transfer) // config_num = 0 will un-configure device. Note: config_num = config_descriptor_index + 1 diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 38711e382..fd33d6cfc 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -510,6 +510,24 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * return true; } +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + + return false; + +// uint8_t const epnum = tu_edpt_number(ep_addr); +// ehci_qhd_t* qhd; +// +// // TODO ISO not supported +// if (epnum == 0) { +// qhd = qhd_control(dev_addr); +// }else { +// qhd = qhd_get_from_addr(dev_addr, ep_addr); +// } +} + bool hcd_edpt_clear_stall(uint8_t daddr, uint8_t ep_addr) { ehci_qhd_t *qhd = qhd_get_from_addr(daddr, ep_addr); -- cgit v1.3.1 From 0da273ea79d7a1c08e3b58301a0b7d3a49c60d13 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 21 Jul 2023 12:52:26 +0700 Subject: add stub hcd_edpt_abort_xfer() for all ports --- src/portable/mentor/musb/hcd_musb.c | 8 ++++++++ src/portable/nxp/khci/hcd_khci.c | 8 ++++++++ src/portable/ohci/ohci.c | 8 ++++++++ src/portable/raspberrypi/pio_usb/hcd_pio_usb.c | 8 ++++++++ src/portable/raspberrypi/rp2040/hcd_rp2040.c | 8 ++++++++ src/portable/renesas/rusb2/hcd_rusb2.c | 8 ++++++++ 6 files changed, 48 insertions(+) (limited to 'src/portable') diff --git a/src/portable/mentor/musb/hcd_musb.c b/src/portable/mentor/musb/hcd_musb.c index 9eb2e005e..5be67a186 100644 --- a/src/portable/mentor/musb/hcd_musb.c +++ b/src/portable/mentor/musb/hcd_musb.c @@ -822,6 +822,14 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t *b return ret; } +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + // TODO not implemented yet + return false; +} + // clear stall, data toggle is also reset to DATA0 bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) { diff --git a/src/portable/nxp/khci/hcd_khci.c b/src/portable/nxp/khci/hcd_khci.c index f6029ee0d..6784049c5 100644 --- a/src/portable/nxp/khci/hcd_khci.c +++ b/src/portable/nxp/khci/hcd_khci.c @@ -562,6 +562,14 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * return true; } +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + // TODO not implemented yet + return false; +} + bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) { if (!tu_edpt_number(ep_addr)) return true; diff --git a/src/portable/ohci/ohci.c b/src/portable/ohci/ohci.c index 3f702d22c..228c43df6 100644 --- a/src/portable/ohci/ohci.c +++ b/src/portable/ohci/ohci.c @@ -543,6 +543,14 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * return true; } +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + // TODO not implemented yet + return false; +} + bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) { ohci_ed_t * const p_ed = ed_from_addr(dev_addr, ep_addr); diff --git a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c index 264af2e7a..fa285327c 100644 --- a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c +++ b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c @@ -138,6 +138,14 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * return pio_usb_host_endpoint_transfer(pio_rhport, dev_addr, ep_addr, buffer, buflen); } +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + // TODO not implemented yet + return false; +} + bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { uint8_t const pio_rhport = RHPORT_PIO(rhport); diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 02f9968a7..5091fa907 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -576,6 +576,14 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * return true; } +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + // TODO not implemented yet + return false; +} + bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { (void) rhport; diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 65bbc656b..0a75d0b47 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -710,6 +710,14 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t *b return r; } +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + // TODO not implemented yet + return false; +} + bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) { uint16_t volatile *ctr = addr_to_pipectr(dev_addr, ep_addr); -- cgit v1.3.1 From 14c98dd863a9cab55fc2981fb826f63eceed4b2d Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 21 Jul 2023 16:39:30 +0700 Subject: minor ehci rename, move code around --- src/portable/ehci/ehci.c | 181 ++++++++++++++++++++++++----------------------- 1 file changed, 91 insertions(+), 90 deletions(-) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index fd33d6cfc..0a26986d5 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -126,53 +126,29 @@ static inline void print_intr(uint32_t intr) { //--------------------------------------------------------------------+ // PROTOTYPE //--------------------------------------------------------------------+ -static inline ehci_link_t* get_period_head(uint8_t rhport, uint32_t interval_ms) -{ - (void) rhport; - return (ehci_link_t*) &ehci_data.period_head_arr[ tu_log2( tu_min32(FRAMELIST_SIZE, interval_ms) ) ]; -} - -static inline ehci_qhd_t* qhd_control(uint8_t dev_addr) -{ - return &ehci_data.control[dev_addr].qhd; -} - -static inline ehci_qhd_t* qhd_async_head(uint8_t rhport) -{ - (void) rhport; - // control qhd of dev0 is used as async head - return qhd_control(0); -} -static inline ehci_qtd_t* qtd_control(uint8_t dev_addr) -{ - return &ehci_data.control[dev_addr].qtd; -} +// weak dcache for non-cacheable MCU +TU_ATTR_WEAK void hcd_dcache_clean(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } +TU_ATTR_WEAK void hcd_dcache_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } +TU_ATTR_WEAK void hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } +TU_ATTR_ALWAYS_INLINE static inline ehci_link_t* list_get_period_head(uint8_t rhport, uint32_t interval_ms); +TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* list_get_async_head(uint8_t rhport); -static inline ehci_qhd_t* qhd_next (ehci_qhd_t const * p_qhd); -static inline ehci_qhd_t* qhd_find_free (void); -static inline ehci_qhd_t* qhd_get_from_addr (uint8_t dev_addr, uint8_t ep_addr); +TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* qhd_control(uint8_t dev_addr); +TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* qhd_next (ehci_qhd_t const * p_qhd); +TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* qhd_find_free (void); +static ehci_qhd_t* qhd_get_from_addr (uint8_t dev_addr, uint8_t ep_addr); static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc); static void qhd_attach_qtd(ehci_qhd_t *qhd, ehci_qtd_t *qtd); -static inline ehci_qtd_t* qtd_find_free (void); +TU_ATTR_ALWAYS_INLINE static inline ehci_qtd_t* qtd_control(uint8_t dev_addr); +TU_ATTR_ALWAYS_INLINE static inline ehci_qtd_t* qtd_find_free (void); static void qtd_init (ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes); static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t new_type); static inline ehci_link_t* list_next (ehci_link_t const *p_link); - -TU_ATTR_WEAK void hcd_dcache_clean(void const* addr, uint32_t data_size) { - (void) addr; (void) data_size; -} - -TU_ATTR_WEAK void hcd_dcache_invalidate(void const* addr, uint32_t data_size) { - (void) addr; (void) data_size; -} - -TU_ATTR_WEAK void hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { - (void) addr; (void) data_size; -} +static void list_remove_qhd_by_daddr(ehci_link_t* list_head, uint8_t dev_addr); //--------------------------------------------------------------------+ // HCD API @@ -274,7 +250,7 @@ void hcd_device_close(uint8_t rhport, uint8_t daddr) } // Remove from async list - list_remove_qhd_by_daddr((ehci_link_t *) qhd_async_head(rhport), daddr); + list_remove_qhd_by_daddr((ehci_link_t *) list_get_async_head(rhport), daddr); // Remove from all interval period list for(uint8_t i = 0; i < TU_ARRAY_SIZE(ehci_data.period_head_arr); i++) { @@ -286,37 +262,42 @@ void hcd_device_close(uint8_t rhport, uint8_t daddr) } static void init_periodic_list(uint8_t rhport) { + (void) rhport; + // Build the polling interval tree with 1 ms, 2 ms, 4 ms and 8 ms (framesize) only for ( uint32_t i = 0; i < TU_ARRAY_SIZE(ehci_data.period_head_arr); i++ ) { ehci_data.period_head_arr[i].int_smask = 1; // queue head in period list must have smask non-zero ehci_data.period_head_arr[i].qtd_overlay.halted = 1; // dummy node, always inactive } - ehci_link_t * const framelist = ehci_data.period_framelist; - ehci_link_t * const period_1ms = get_period_head(rhport, 1u); - + // TODO EHCI_FRAMELIST_SIZE with other size than 8 // all links --> period_head_arr[0] (1ms) // 0, 2, 4, 6 etc --> period_head_arr[1] (2ms) // 1, 5 --> period_head_arr[2] (4ms) // 3 --> period_head_arr[3] (8ms) - // TODO EHCI_FRAMELIST_SIZE with other size than 8 + ehci_link_t * const framelist = ehci_data.period_framelist; + ehci_link_t * const head_1ms = (ehci_link_t *) &ehci_data.period_head_arr[0]; + ehci_link_t * const head_2ms = (ehci_link_t *) &ehci_data.period_head_arr[1]; + ehci_link_t * const head_4ms = (ehci_link_t *) &ehci_data.period_head_arr[2]; + ehci_link_t * const head_8ms = (ehci_link_t *) &ehci_data.period_head_arr[3]; + for (uint32_t i = 0; i < FRAMELIST_SIZE; i++) { - framelist[i].address = (uint32_t) period_1ms; + framelist[i].address = (uint32_t) head_1ms; framelist[i].type = EHCI_QTYPE_QHD; } for (uint32_t i = 0; i < FRAMELIST_SIZE; i += 2) { - list_insert(framelist + i, get_period_head(rhport, 2u), EHCI_QTYPE_QHD); + list_insert(framelist + i, head_2ms, EHCI_QTYPE_QHD); } for (uint32_t i = 1; i < FRAMELIST_SIZE; i += 4) { - list_insert(framelist + i, get_period_head(rhport, 4u), EHCI_QTYPE_QHD); + list_insert(framelist + i, head_4ms, EHCI_QTYPE_QHD); } - list_insert(framelist + 3, get_period_head(rhport, 8u), EHCI_QTYPE_QHD); + list_insert(framelist + 3, head_8ms, EHCI_QTYPE_QHD); - period_1ms->terminate = 1; + head_1ms->terminate = 1; } bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) @@ -345,7 +326,7 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) EHCI_INT_MASK_NXP_PERIODIC | EHCI_INT_MASK_NXP_ASYNC | EHCI_INT_MASK_FRAMELIST_ROLLOVER; //------------- Asynchronous List -------------// - ehci_qhd_t * const async_head = qhd_async_head(rhport); + ehci_qhd_t * const async_head = list_get_async_head(rhport); tu_memclr(async_head, sizeof(ehci_qhd_t)); async_head->next.address = (uint32_t) async_head; // circular list, next is itself @@ -426,11 +407,11 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const { case TUSB_XFER_CONTROL: case TUSB_XFER_BULK: - list_head = (ehci_link_t*) qhd_async_head(rhport); + list_head = (ehci_link_t*) list_get_async_head(rhport); break; case TUSB_XFER_INTERRUPT: - list_head = get_period_head(rhport, p_qhd->interval_ms); + list_head = list_get_period_head(rhport, p_qhd->interval_ms); break; case TUSB_XFER_ISOCHRONOUS: @@ -439,10 +420,8 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const default: break; } - TU_ASSERT(list_head); - // TODO might need to disable async/period list list_insert(list_head, (ehci_link_t*) p_qhd, EHCI_QTYPE_QHD); hcd_dcache_clean(p_qhd, sizeof(ehci_qhd_t)); @@ -622,8 +601,8 @@ void async_list_xfer_complete_isr(ehci_qhd_t * const async_head) TU_ATTR_ALWAYS_INLINE static inline void period_list_xfer_complete_isr(uint8_t rhport, uint32_t interval_ms) { - uint32_t const period_1ms_addr = (uint32_t) get_period_head(rhport, 1u); - ehci_link_t next_link = * get_period_head(rhport, interval_ms); + uint32_t const period_1ms_addr = (uint32_t) list_get_period_head(rhport, 1u); + ehci_link_t next_link = *list_get_period_head(rhport, interval_ms); while (!next_link.terminate) { if (interval_ms > 1 && period_1ms_addr == tu_align32(next_link.address)) { @@ -721,7 +700,7 @@ TU_ATTR_ALWAYS_INLINE static inline void xfer_error_isr(uint8_t rhport) { //------------- async list -------------// - ehci_qhd_t * const async_head = qhd_async_head(rhport); + ehci_qhd_t * const async_head = list_get_async_head(rhport); ehci_qhd_t *p_qhd = async_head; do { @@ -731,10 +710,10 @@ void xfer_error_isr(uint8_t rhport) }while(p_qhd != async_head); // async list traversal, stop if loop around //------------- TODO refractor period list -------------// - uint32_t const period_1ms_addr = (uint32_t) get_period_head(rhport, 1u); + uint32_t const period_1ms_addr = (uint32_t) list_get_period_head(rhport, 1u); for (uint32_t interval_ms=1; interval_ms <= FRAMELIST_SIZE; interval_ms *= 2) { - ehci_link_t next_item = * get_period_head(rhport, interval_ms); + ehci_link_t next_item = *list_get_period_head(rhport, interval_ms); // TODO abstract max loop guard for period while( !next_item.terminate && @@ -801,7 +780,7 @@ void hcd_int_handler(uint8_t rhport) //------------- some QTD/SITD/ITD with IOC set is completed -------------// if (int_status & EHCI_INT_MASK_NXP_ASYNC) { - async_list_xfer_complete_isr(qhd_async_head(rhport)); + async_list_xfer_complete_isr(list_get_async_head(rhport)); regs->status = EHCI_INT_MASK_NXP_ASYNC; // Acknowledge } @@ -828,35 +807,62 @@ void hcd_int_handler(uint8_t rhport) } //--------------------------------------------------------------------+ -// HELPER +// List Managing Helper //--------------------------------------------------------------------+ +// Get head of periodic list +TU_ATTR_ALWAYS_INLINE static inline ehci_link_t* list_get_period_head(uint8_t rhport, uint32_t interval_ms) { + (void) rhport; + return (ehci_link_t*) &ehci_data.period_head_arr[ tu_log2( tu_min32(FRAMELIST_SIZE, interval_ms) ) ]; +} -//------------- queue head helper -------------// -static inline ehci_qhd_t* qhd_find_free (void) +// Get head of async list +TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* list_get_async_head(uint8_t rhport) { + (void) rhport; + return qhd_control(0); // control qhd of dev0 is used as async head +} + +// insert at head +static inline void list_insert(ehci_link_t *current, ehci_link_t *new, uint8_t new_type) { - for (uint32_t i=0; iaddress = current->address; + current->address = ((uint32_t) new) | (new_type << 1); +} + +static inline ehci_link_t* list_next(ehci_link_t const *p_link) +{ + return (ehci_link_t*) tu_align32(p_link->address); +} + +//--------------------------------------------------------------------+ +// Queue Header helper +//--------------------------------------------------------------------+ + +// Get queue head for control transfer (always available) +TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* qhd_control(uint8_t dev_addr) { + return &ehci_data.control[dev_addr].qhd; +} + +// Find a free queue head +TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t *qhd_find_free(void) { + for ( uint32_t i = 0; i < QHD_MAX; i++ ) { if ( !ehci_data.qhd_pool[i].used ) return &ehci_data.qhd_pool[i]; } - return NULL; } -static inline ehci_qhd_t* qhd_next(ehci_qhd_t const * p_qhd) -{ - return (ehci_qhd_t*) tu_align32(p_qhd->next.address); +// Next queue head link +TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t *qhd_next(ehci_qhd_t const *p_qhd) { + return (ehci_qhd_t *) tu_align32(p_qhd->next.address); } -static inline ehci_qhd_t* qhd_get_from_addr(uint8_t dev_addr, uint8_t ep_addr) -{ - ehci_qhd_t* qhd_pool = ehci_data.qhd_pool; +// Get queue head from address +static ehci_qhd_t *qhd_get_from_addr(uint8_t dev_addr, uint8_t ep_addr) { + ehci_qhd_t *qhd_pool = ehci_data.qhd_pool; - for(uint32_t i=0; i cannot be cleared (ehci halted otherwise) @@ -938,6 +945,7 @@ static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t c } } +// Attach a TD to queue head static void qhd_attach_qtd(ehci_qhd_t *qhd, ehci_qtd_t *qtd) { qhd->attached_qtd = qtd; qhd->attached_buffer = qtd->buffer[0]; @@ -949,9 +957,16 @@ static void qhd_attach_qtd(ehci_qhd_t *qhd, ehci_qtd_t *qtd) { hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); } +//--------------------------------------------------------------------+ +// Queue TD helper +//--------------------------------------------------------------------+ + +// Get TD for control transfer (always available) +TU_ATTR_ALWAYS_INLINE static inline ehci_qtd_t* qtd_control(uint8_t dev_addr) { + return &ehci_data.control[dev_addr].qtd; +} -//------------- TD helper -------------// -static inline ehci_qtd_t *qtd_find_free(void) { +TU_ATTR_ALWAYS_INLINE static inline ehci_qtd_t *qtd_find_free(void) { for (uint32_t i = 0; i < QTD_MAX; i++) { if (!ehci_data.qtd_pool[i].used) return &ehci_data.qtd_pool[i]; } @@ -979,18 +994,4 @@ static void qtd_init(ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes) } } -//------------- List Managing Helper -------------// - -// insert at head -static inline void list_insert(ehci_link_t *current, ehci_link_t *new, uint8_t new_type) -{ - new->address = current->address; - current->address = ((uint32_t) new) | (new_type << 1); -} - -static inline ehci_link_t* list_next(ehci_link_t const *p_link) -{ - return (ehci_link_t*) tu_align32(p_link->address); -} - #endif -- cgit v1.3.1 From c122e9df73331fa60d1713c7cc4cf46251b0cd76 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 21 Jul 2023 19:06:36 +0700 Subject: implement hcd_edpt_abort_xfer() for EHCI, also move thing around a bit --- src/common/tusb_common.h | 2 + src/host/hcd.h | 1 + src/host/usbh.c | 10 ++- src/host/usbh.h | 1 + src/portable/ehci/ehci.c | 200 +++++++++++++++++++++++++++++------------------ src/portable/ehci/ehci.h | 19 +++-- 6 files changed, 147 insertions(+), 86 deletions(-) (limited to 'src/portable') diff --git a/src/common/tusb_common.h b/src/common/tusb_common.h index 957491aa9..b3d9fc7cd 100644 --- a/src/common/tusb_common.h +++ b/src/common/tusb_common.h @@ -53,6 +53,8 @@ #define U32_TO_U8S_LE(_u32) TU_U32_BYTE0(_u32), TU_U32_BYTE1(_u32), TU_U32_BYTE2(_u32), TU_U32_BYTE3(_u32) #define TU_BIT(n) (1UL << (n)) + +// Generate a mask with bit from high (31) to low (0) set, e.g TU_GENMASK(3, 0) = 0b1111 #define TU_GENMASK(h, l) ( (UINT32_MAX << (l)) & (UINT32_MAX >> (31 - (h))) ) //--------------------------------------------------------------------+ diff --git a/src/host/hcd.h b/src/host/hcd.h index cbfffb349..90bfd79db 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -172,6 +172,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen); // Abort a queued transfer. Note: it can only abort transfer that has not been started +// Return true if a queued transfer is aborted, false if there is no transfer to abort bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr); // Submit a special transfer to send 8-byte Setup Packet, when complete hcd_event_xfer_complete() must be invoked diff --git a/src/host/usbh.c b/src/host/usbh.c index bbf333d5f..15c48be47 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -718,9 +718,15 @@ bool tuh_edpt_abort_xfer(uint8_t daddr, uint8_t ep_addr) { uint8_t const dir = tu_edpt_dir(ep_addr); // skip if not busy - if (!dev->ep_status[epnum][dir].busy) return true; + TU_VERIFY(dev->ep_status[epnum][dir].busy); - return hcd_edpt_abort_xfer(dev->rhport, daddr, ep_addr); + bool const ret = hcd_edpt_abort_xfer(dev->rhport, daddr, ep_addr); + if (ret) { + // mark as ready if transfer is aborted + dev->ep_status[epnum][dir].busy = false; + } + + return ret; } //--------------------------------------------------------------------+ diff --git a/src/host/usbh.h b/src/host/usbh.h index d765f6744..0d56f40c9 100644 --- a/src/host/usbh.h +++ b/src/host/usbh.h @@ -176,6 +176,7 @@ bool tuh_edpt_xfer(tuh_xfer_t* xfer); bool tuh_edpt_open(uint8_t daddr, tusb_desc_endpoint_t const * desc_ep); // Abort a queued transfer. Note: it can only abort transfer that has not been started +// Return true if a queued transfer is aborted, false if there is no transfer to abort bool tuh_edpt_abort_xfer(uint8_t daddr, uint8_t ep_addr); // Set Configuration (control transfer) diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 0a26986d5..6388add08 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -48,8 +48,8 @@ #ifdef TUP_USBIP_CHIPIDEA_HS // NXP Transdimension: 8 elements #define FRAMELIST_SIZE_BIT_VALUE 7u - #define FRAMELIST_SIZE_USBCMD_VALUE (((FRAMELIST_SIZE_BIT_VALUE & 3) << EHCI_USBCMD_POS_FRAMELIST_SIZE) | \ - ((FRAMELIST_SIZE_BIT_VALUE >> 2) << EHCI_USBCMD_POS_NXP_FRAMELIST_SIZE_MSB)) + #define FRAMELIST_SIZE_USBCMD_VALUE (((FRAMELIST_SIZE_BIT_VALUE & 3) << EHCI_USBCMD_FRAMELIST_SIZE_SHIFT) | \ + ((FRAMELIST_SIZE_BIT_VALUE >> 2) << EHCI_USBCMD_CHIPIDEA_FRAMELIST_SIZE_MSB_SHIFT)) #else // STD EHCI: 256 elements #define FRAMELIST_SIZE_BIT_VALUE 2u @@ -132,24 +132,46 @@ TU_ATTR_WEAK void hcd_dcache_clean(void const* addr, uint32_t data_size) { (void TU_ATTR_WEAK void hcd_dcache_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } TU_ATTR_WEAK void hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; } -TU_ATTR_ALWAYS_INLINE static inline ehci_link_t* list_get_period_head(uint8_t rhport, uint32_t interval_ms); -TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* list_get_async_head(uint8_t rhport); - TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* qhd_control(uint8_t dev_addr); TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* qhd_next (ehci_qhd_t const * p_qhd); TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* qhd_find_free (void); static ehci_qhd_t* qhd_get_from_addr (uint8_t dev_addr, uint8_t ep_addr); static void qhd_init(ehci_qhd_t *p_qhd, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc); static void qhd_attach_qtd(ehci_qhd_t *qhd, ehci_qtd_t *qtd); +static void qhd_remove_qtd(ehci_qhd_t *qhd); TU_ATTR_ALWAYS_INLINE static inline ehci_qtd_t* qtd_control(uint8_t dev_addr); TU_ATTR_ALWAYS_INLINE static inline ehci_qtd_t* qtd_find_free (void); static void qtd_init (ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes); -static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t new_type); -static inline ehci_link_t* list_next (ehci_link_t const *p_link); +TU_ATTR_ALWAYS_INLINE static inline ehci_link_t* list_get_period_head(uint8_t rhport, uint32_t interval_ms); +TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* list_get_async_head(uint8_t rhport); +TU_ATTR_ALWAYS_INLINE static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t new_type); +TU_ATTR_ALWAYS_INLINE static inline ehci_link_t* list_next (ehci_link_t const *p_link); static void list_remove_qhd_by_daddr(ehci_link_t* list_head, uint8_t dev_addr); +static void ehci_disable_schedule(ehci_registers_t* regs, bool is_period) { + // maybe have a timeout for status + if (is_period) { + regs->command_bm.periodic_enable = 0; + while(regs->status_bm.periodic_status) {} + } else { + regs->command_bm.async_enable = 0; + while(regs->status_bm.async_status) {} // should have a timeout + } +} + +static void ehci_enable_schedule(ehci_registers_t* regs, bool is_period) { + // maybe have a timeout for status + if (is_period) { + regs->command_bm.periodic_enable = 1; + while ( 0 == regs->status_bm.periodic_status ) {} + } else { + regs->command_bm.async_enable = 1; + while( 0 == regs->status_bm.async_status ) {} + } +} + //--------------------------------------------------------------------+ // HCD API //--------------------------------------------------------------------+ @@ -204,43 +226,6 @@ tusb_speed_t hcd_port_speed_get(uint8_t rhport) return (tusb_speed_t) ehci_data.regs->portsc_bm.nxp_port_speed; // NXP specific port speed } -static void list_remove_qhd_by_daddr(ehci_link_t* list_head, uint8_t dev_addr) { - ehci_link_t* prev = list_head; - - while (prev && !prev->terminate) { - ehci_qhd_t* qhd = (ehci_qhd_t*) (uintptr_t) list_next(prev); - - // done if loop back to head - if ( (uintptr_t) qhd == (uintptr_t) list_head) { - break; - } - - if ( qhd->dev_addr == dev_addr ) { - // TODO deactivate all TD, wait for QHD to inactive before removal - prev->address = qhd->next.address; - - // EHCI 4.8.2 link the removed qhd's next to async head (which always reachable by Host Controller) - qhd->next.address = ((uint32_t) list_head) | (EHCI_QTYPE_QHD << 1); - - if ( qhd->int_smask ) - { - // period list queue element is guarantee to be free in the next frame (1 ms) - qhd->used = 0; - }else - { - // async list use async advance handshake - // mark as removing, will completely re-usable when async advance isr occurs - qhd->removing = 1; - } - - hcd_dcache_clean(qhd, sizeof(ehci_qhd_t)); - hcd_dcache_clean(prev, sizeof(ehci_qhd_t)); - }else { - prev = list_next(prev); - } - } -} - // Close all opened endpoint belong to this device void hcd_device_close(uint8_t rhport, uint8_t daddr) { @@ -347,8 +332,7 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) regs->nxp_tt_control = 0; //------------- USB CMD Register -------------// - regs->command |= TU_BIT(EHCI_USBCMD_POS_RUN_STOP) | TU_BIT(EHCI_USBCMD_POS_ASYNC_ENABLE) | - TU_BIT(EHCI_USBCMD_POS_PERIOD_ENABLE) | // TODO enable period list only there is int/iso endpoint + regs->command |= EHCI_USBCMD_RUN_STOP | EHCI_USBCMD_PERIOD_SCHEDULE_ENABLE | EHCI_USBCMD_ASYNC_SCHEDULE_ENABLE | FRAMELIST_SIZE_USBCMD_VALUE; //------------- ConfigFlag Register (skip) -------------// @@ -358,7 +342,7 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) if (ehci_data.cap_regs->hcsparams_bm.port_power_control) { // mask out all change bits since they are Write 1 to clear uint32_t portsc = (regs->portsc & ~EHCI_PORTSC_MASK_W1C); - portsc |= ECHI_PORTSC_MASK_PORT_POWER; + portsc |= EHCI_PORTSC_MASK_PORT_POWER; regs->portsc = portsc; } @@ -455,20 +439,17 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); - ehci_qhd_t* qhd; + ehci_qhd_t* qhd = qhd_get_from_addr(dev_addr, ep_addr); ehci_qtd_t* qtd; if (epnum == 0) { - qhd = qhd_control(dev_addr); qtd = qtd_control(dev_addr); - qtd_init(qtd, buffer, buflen); // first data toggle is always 1 (data & setup stage) qtd->data_toggle = 1; qtd->pid = dir ? EHCI_PID_IN : EHCI_PID_OUT; } else { - qhd = qhd_get_from_addr(dev_addr, ep_addr); qtd = qtd_find_free(); TU_ASSERT(qtd); @@ -491,20 +472,34 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { (void) rhport; - (void) dev_addr; - (void) ep_addr; - return false; + // TODO ISO not supported yet + ehci_qhd_t* qhd = qhd_get_from_addr(dev_addr, ep_addr); + ehci_qtd_t * volatile qtd = qhd->attached_qtd; + TU_VERIFY(qtd != NULL); // no queued transfer + + hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); + TU_VERIFY(qtd->active); // transfer is already complete + + // HC is still processing, disable HC list schedule before making changes + bool const is_period = (qhd->interval_ms > 0); + + ehci_disable_schedule(ehci_data.regs, is_period); + + // check active bit again just in case HC has just processed the TD + bool const still_active = qtd->active; + if (still_active) { + // remove TD from QH overlay + qhd->qtd_overlay.next.terminate = 1; + hcd_dcache_clean(qhd, sizeof(ehci_qhd_t)); + + // remove TD from QH software list + qhd_remove_qtd(qhd); + } -// uint8_t const epnum = tu_edpt_number(ep_addr); -// ehci_qhd_t* qhd; -// -// // TODO ISO not supported -// if (epnum == 0) { -// qhd = qhd_control(dev_addr); -// }else { -// qhd = qhd_get_from_addr(dev_addr, ep_addr); -// } + ehci_enable_schedule(ehci_data.regs, is_period); + + return still_active; // true if removed an active transfer } bool hcd_edpt_clear_stall(uint8_t daddr, uint8_t ep_addr) @@ -554,8 +549,12 @@ void port_connect_status_change_isr(uint8_t rhport) TU_ATTR_ALWAYS_INLINE static inline void qhd_xfer_complete_isr(ehci_qhd_t * qhd) { // examine TD attached to queue head - ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) qhd->attached_qtd; - if (qtd == NULL) return; // no TD attached + ehci_qtd_t * volatile qtd = qhd->attached_qtd; + + if (qtd == NULL) { + return; // no TD attached + } + hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); // TD is still active, no need to process @@ -572,9 +571,7 @@ void qhd_xfer_complete_isr(ehci_qhd_t * qhd) { } // remove and free TD before invoking callback - qhd->attached_qtd = NULL; - qhd->attached_buffer = 0; - qtd->used = 0; // free QTD + qhd_remove_qtd(qhd); // notify usbh uint8_t const ep_addr = tu_edpt_addr(qhd->ep_number, dir); @@ -677,9 +674,7 @@ void qhd_xfer_error_isr(ehci_qhd_t * qhd) } // remove and free TD before invoking callback - qhd->attached_qtd = NULL; - qhd->attached_buffer = 0; - qtd->used = 0; // free QTD + qhd_remove_qtd(qhd); if (0 == qhd->ep_number ) { // control cannot be halted @@ -822,18 +817,55 @@ TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t* list_get_async_head(uint8_t rhpo return qhd_control(0); // control qhd of dev0 is used as async head } -// insert at head -static inline void list_insert(ehci_link_t *current, ehci_link_t *new, uint8_t new_type) +TU_ATTR_ALWAYS_INLINE static inline ehci_link_t* list_next(ehci_link_t const *p_link) { + return (ehci_link_t*) tu_align32(p_link->address); +} + +TU_ATTR_ALWAYS_INLINE static inline void list_insert(ehci_link_t *current, ehci_link_t *new, uint8_t new_type) { new->address = current->address; current->address = ((uint32_t) new) | (new_type << 1); } -static inline ehci_link_t* list_next(ehci_link_t const *p_link) -{ - return (ehci_link_t*) tu_align32(p_link->address); +// Remove all queue head belong to this device address +static void list_remove_qhd_by_daddr(ehci_link_t* list_head, uint8_t dev_addr) { + ehci_link_t* prev = list_head; + + while (prev && !prev->terminate) { + ehci_qhd_t* qhd = (ehci_qhd_t*) (uintptr_t) list_next(prev); + + // done if loop back to head + if ( (uintptr_t) qhd == (uintptr_t) list_head) { + break; + } + + if ( qhd->dev_addr == dev_addr ) { + // TODO deactivate all TD, wait for QHD to inactive before removal + prev->address = qhd->next.address; + + // EHCI 4.8.2 link the removed qhd's next to async head (which always reachable by Host Controller) + qhd->next.address = ((uint32_t) list_head) | (EHCI_QTYPE_QHD << 1); + + if ( qhd->int_smask ) + { + // period list queue element is guarantee to be free in the next frame (1 ms) + qhd->used = 0; + }else + { + // async list use async advance handshake + // mark as removing, will completely re-usable when async advance isr occurs + qhd->removing = 1; + } + + hcd_dcache_clean(qhd, sizeof(ehci_qhd_t)); + hcd_dcache_clean(prev, sizeof(ehci_qhd_t)); + }else { + prev = list_next(prev); + } + } } + //--------------------------------------------------------------------+ // Queue Header helper //--------------------------------------------------------------------+ @@ -856,8 +888,12 @@ TU_ATTR_ALWAYS_INLINE static inline ehci_qhd_t *qhd_next(ehci_qhd_t const *p_qhd return (ehci_qhd_t *) tu_align32(p_qhd->next.address); } -// Get queue head from address +// Get queue head from device + endpoint address static ehci_qhd_t *qhd_get_from_addr(uint8_t dev_addr, uint8_t ep_addr) { + if ( 0 == tu_edpt_number(ep_addr) ) { + return qhd_control(dev_addr); + } + ehci_qhd_t *qhd_pool = ehci_data.qhd_pool; for ( uint32_t i = 0; i < QHD_MAX; i++ ) { @@ -957,6 +993,16 @@ static void qhd_attach_qtd(ehci_qhd_t *qhd, ehci_qtd_t *qtd) { hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); } +// Remove an attached TD from queue head +static void qhd_remove_qtd(ehci_qhd_t *qhd) { + ehci_qtd_t * volatile qtd = qhd->attached_qtd; + + qhd->attached_qtd = NULL; + qhd->attached_buffer = 0; + + qtd->used = 0; // free QTD +} + //--------------------------------------------------------------------+ // Queue TD helper //--------------------------------------------------------------------+ diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index 8338fb419..05de80539 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -289,12 +289,17 @@ enum { }; enum { - EHCI_USBCMD_POS_RUN_STOP = 0, - EHCI_USBCMD_POS_FRAMELIST_SIZE = 2, - EHCI_USBCMD_POS_PERIOD_ENABLE = 4, - EHCI_USBCMD_POS_ASYNC_ENABLE = 5, - EHCI_USBCMD_POS_NXP_FRAMELIST_SIZE_MSB = 15, - EHCI_USBCMD_POS_INTERRUPT_THRESHOLD = 16 + EHCI_USBCMD_FRAMELIST_SIZE_SHIFT = 2, // [2..3] + EHCI_USBCMD_CHIPIDEA_FRAMELIST_SIZE_MSB_SHIFT = 15, + EHCI_USBCMD_INTERRUPT_THRESHOLD_SHIFT = 16 +}; + +enum { + EHCI_USBCMD_RUN_STOP = TU_BIT(0), // [0..0] 1 = Run, 0 = Stop + EHCI_USBCMD_HCRESET = TU_BIT(1), // [1..1] SW write 1 to reset HC, clear by HC when complete + EHCI_USBCMD_PERIOD_SCHEDULE_ENABLE = TU_BIT(4), // [4..4] Enable periodic schedule + EHCI_USBCMD_ASYNC_SCHEDULE_ENABLE = TU_BIT(5), // [5..5] Enable async schedule + EHCI_USBCMD_INTR_ON_ASYNC_ADVANCE_DOORBELL = TU_BIT(6), // [6..6] Tell HC to interrupt next time it advances async list. Clear by HC }; enum { @@ -306,7 +311,7 @@ enum { EHCI_PORTSC_MASK_FORCE_RESUME = TU_BIT(6), EHCI_PORTSC_MASK_PORT_SUSPEND = TU_BIT(7), EHCI_PORTSC_MASK_PORT_RESET = TU_BIT(8), - ECHI_PORTSC_MASK_PORT_POWER = TU_BIT(12), + EHCI_PORTSC_MASK_PORT_POWER = TU_BIT(12), EHCI_PORTSC_MASK_W1C = EHCI_PORTSC_MASK_CONNECT_STATUS_CHANGE | -- cgit v1.3.1 From e2f28bc134446dc081766055171ca427afd4f564 Mon Sep 17 00:00:00 2001 From: emb4fun Date: Sun, 23 Jul 2023 10:53:22 +0200 Subject: Added support for the NXP K64 series --- hw/bsp/board_mcu.h | 2 +- src/common/tusb_mcu.h | 2 +- src/portable/nxp/khci/dcd_khci.c | 14 ++++++++++++++ src/tusb_option.h | 1 + 4 files changed, 17 insertions(+), 2 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/board_mcu.h b/hw/bsp/board_mcu.h index e5d2bb608..3928435f0 100644 --- a/hw/bsp/board_mcu.h +++ b/hw/bsp/board_mcu.h @@ -47,7 +47,7 @@ #elif TU_CHECK_MCU(OPT_MCU_LPC51UXX, OPT_MCU_LPC54XXX, OPT_MCU_LPC55XX, OPT_MCU_MCXN9) #include "fsl_device_registers.h" -#elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32L) +#elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32L, OPT_MCU_KINETIS_K64) #include "fsl_device_registers.h" #elif CFG_TUSB_MCU == OPT_MCU_NRF5X diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 9f3be78fd..4a0c5acef 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -97,7 +97,7 @@ #define TUP_DCD_ENDPOINT_MAX 8 #define TUP_RHPORT_HIGHSPEED 1 -#elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32L) +#elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32L, OPT_MCU_KINETIS_K64) #define TUP_USBIP_CHIPIDEA_FS #define TUP_USBIP_CHIPIDEA_FS_KINETIS #define TUP_DCD_ENDPOINT_MAX 16 diff --git a/src/portable/nxp/khci/dcd_khci.c b/src/portable/nxp/khci/dcd_khci.c index 52f4145f2..d957338ad 100644 --- a/src/portable/nxp/khci/dcd_khci.c +++ b/src/portable/nxp/khci/dcd_khci.c @@ -269,8 +269,22 @@ void dcd_init(uint8_t rhport) { (void) rhport; +#if (CFG_TUSB_MCU == OPT_MCU_KINETIS_K64) + uint32_t clk_recover_irc_en; + uint32_t clk_recover_ctrl; + + clk_recover_irc_en = KHCI->CLK_RECOVER_IRC_EN; + clk_recover_ctrl = KHCI->CLK_RECOVER_CTRL; + + KHCI->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; + while (KHCI->USBTRC0 & USB_USBTRC0_USBRESET_MASK); + + KHCI->CLK_RECOVER_IRC_EN = clk_recover_irc_en; + KHCI->CLK_RECOVER_CTRL |= clk_recover_ctrl; +#else KHCI->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; while (KHCI->USBTRC0 & USB_USBTRC0_USBRESET_MASK); +#endif tu_memclr(&_dcd, sizeof(_dcd)); KHCI->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ diff --git a/src/tusb_option.h b/src/tusb_option.h index c792efe6a..bbaa2a53a 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -121,6 +121,7 @@ #define OPT_MCU_KINETIS_KL 1200 ///< NXP KL series #define OPT_MCU_KINETIS_K32L 1201 ///< NXP K32L series #define OPT_MCU_KINETIS_K32 1201 ///< Alias to K32L +#define OPT_MCU_KINETIS_K64 1202 ///< NXP K64 series #define OPT_MCU_MKL25ZXX 1200 ///< Alias to KL (obsolete) #define OPT_MCU_K32L2BXX 1201 ///< Alias to K32 (obsolete) -- cgit v1.3.1 From ef49b93532a7360703ae87d36cf463169f86f20b Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 24 Jul 2023 15:46:21 +0700 Subject: rename CFG_TUSB_MEM_SECTION to CFG_TUD_MEM_SECTION in device stack CFG_TUD_MEM_SECTION is default to CFG_TUSB_MEM_SECTION --- hw/bsp/lpc40/family.cmake | 1 + hw/bsp/lpc40/family.mk | 3 +- lib/networking/rndis_reports.c | 2 +- src/class/audio/audio_device.c | 44 ++++++++++++------------ src/class/bth/bth_device.c | 2 +- src/class/cdc/cdc_device.c | 2 +- src/class/dfu/dfu_device.c | 2 +- src/class/hid/hid_device.c | 2 +- src/class/midi/midi_device.c | 2 +- src/class/msc/msc_device.c | 4 +-- src/class/net/ecm_rndis_device.c | 12 +++---- src/class/net/ncm_device.c | 6 ++-- src/class/usbtmc/usbtmc_device.c | 2 +- src/class/vendor/vendor_device.c | 2 +- src/class/video/video_device.c | 4 +-- src/device/usbd_control.c | 2 +- src/portable/bridgetek/ft9xx/dcd_ft9xx.c | 2 +- src/portable/chipidea/ci_fs/dcd_ci_fs.c | 2 +- src/portable/chipidea/ci_hs/dcd_ci_hs.c | 2 +- src/portable/microchip/pic/dcd_pic.c | 2 +- src/portable/microchip/samx7x/dcd_samx7x.c | 2 +- src/portable/mindmotion/mm32/dcd_mm32f327x_otg.c | 2 +- src/portable/nxp/khci/dcd_khci.c | 2 +- src/portable/nxp/lpc17_40/dcd_lpc17_40.c | 2 +- src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c | 6 ++-- src/tusb_option.h | 42 ++++++---------------- 26 files changed, 68 insertions(+), 88 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/lpc40/family.cmake b/hw/bsp/lpc40/family.cmake index 03caa4385..54410e1a7 100644 --- a/hw/bsp/lpc40/family.cmake +++ b/hw/bsp/lpc40/family.cmake @@ -38,6 +38,7 @@ function(add_board_target BOARD_TARGET) target_compile_definitions(${BOARD_TARGET} PUBLIC __USE_LPCOPEN CORE_M4 + CFG_TUSB_MEM_SECTION=__attribute__\(\(section\(\".data.$RAM2\"\)\)\) ) target_include_directories(${BOARD_TARGET} PUBLIC ${SDK_DIR}/inc diff --git a/hw/bsp/lpc40/family.mk b/hw/bsp/lpc40/family.mk index 47d25b885..0fc7095f5 100644 --- a/hw/bsp/lpc40/family.mk +++ b/hw/bsp/lpc40/family.mk @@ -9,8 +9,7 @@ CFLAGS += \ -nostdlib \ -DCORE_M4 \ -D__USE_LPCOPEN \ - -DCFG_TUD_MEM_SECTION='__attribute__((section(".data.$$RAM2")))' \ - -DCFG_TUH_MEM_SECTION='__attribute__((section(".data.$$RAM2")))' \ + -DCFG_TUSB_MEM_SECTION='__attribute__((section(".data.$$RAM2")))' \ -DCFG_TUSB_MCU=OPT_MCU_LPC40XX # mcu driver cause following warnings diff --git a/lib/networking/rndis_reports.c b/lib/networking/rndis_reports.c index cc14f174c..60afb8615 100644 --- a/lib/networking/rndis_reports.c +++ b/lib/networking/rndis_reports.c @@ -43,7 +43,7 @@ static usb_eth_stat_t usb_eth_stat = { 0, 0, 0, 0 }; static uint32_t oid_packet_filter = 0x0000000; static rndis_state_t rndis_state; -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN static uint8_t ndis_report[8] = { 0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00 }; +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN static uint8_t ndis_report[8] = { 0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00 }; static const uint32_t OIDSupportedList[] = { diff --git a/src/class/audio/audio_device.c b/src/class/audio/audio_device.c index e5dbe988a..1a7ce7870 100644 --- a/src/class/audio/audio_device.c +++ b/src/class/audio/audio_device.c @@ -113,21 +113,21 @@ // EP IN software buffers and mutexes #if CFG_TUD_AUDIO_ENABLE_EP_IN && !CFG_TUD_AUDIO_ENABLE_ENCODING #if CFG_TUD_AUDIO_FUNC_1_EP_IN_SW_BUF_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_in_sw_buf_1[CFG_TUD_AUDIO_FUNC_1_EP_IN_SW_BUF_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_in_sw_buf_1[CFG_TUD_AUDIO_FUNC_1_EP_IN_SW_BUF_SZ]; #if CFG_FIFO_MUTEX osal_mutex_def_t ep_in_ff_mutex_wr_1; // No need for read mutex as only USB driver reads from FIFO #endif #endif // CFG_TUD_AUDIO_FUNC_1_EP_IN_SW_BUF_SZ > 0 #if CFG_TUD_AUDIO > 1 && CFG_TUD_AUDIO_FUNC_2_EP_IN_SW_BUF_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_in_sw_buf_2[CFG_TUD_AUDIO_FUNC_2_EP_IN_SW_BUF_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_in_sw_buf_2[CFG_TUD_AUDIO_FUNC_2_EP_IN_SW_BUF_SZ]; #if CFG_FIFO_MUTEX osal_mutex_def_t ep_in_ff_mutex_wr_2; // No need for read mutex as only USB driver reads from FIFO #endif #endif // CFG_TUD_AUDIO > 1 && CFG_TUD_AUDIO_FUNC_2_EP_IN_SW_BUF_SZ > 0 #if CFG_TUD_AUDIO > 2 && CFG_TUD_AUDIO_FUNC_3_EP_IN_SW_BUF_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_in_sw_buf_3[CFG_TUD_AUDIO_FUNC_3_EP_IN_SW_BUF_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_in_sw_buf_3[CFG_TUD_AUDIO_FUNC_3_EP_IN_SW_BUF_SZ]; #if CFG_FIFO_MUTEX osal_mutex_def_t ep_in_ff_mutex_wr_3; // No need for read mutex as only USB driver reads from FIFO #endif @@ -139,36 +139,36 @@ // - the software encoding is used - in this case the linear buffers serve as a target memory where logical channels are encoded into #if CFG_TUD_AUDIO_ENABLE_EP_IN && (USE_LINEAR_BUFFER || CFG_TUD_AUDIO_ENABLE_ENCODING) #if CFG_TUD_AUDIO_FUNC_1_EP_IN_SZ_MAX > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_in_1[CFG_TUD_AUDIO_FUNC_1_EP_IN_SZ_MAX]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_in_1[CFG_TUD_AUDIO_FUNC_1_EP_IN_SZ_MAX]; #endif #if CFG_TUD_AUDIO > 1 && CFG_TUD_AUDIO_FUNC_2_EP_IN_SZ_MAX > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_in_2[CFG_TUD_AUDIO_FUNC_2_EP_IN_SZ_MAX]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_in_2[CFG_TUD_AUDIO_FUNC_2_EP_IN_SZ_MAX]; #endif #if CFG_TUD_AUDIO > 2 && CFG_TUD_AUDIO_FUNC_3_EP_IN_SZ_MAX > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_in_3[CFG_TUD_AUDIO_FUNC_3_EP_IN_SZ_MAX]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_in_3[CFG_TUD_AUDIO_FUNC_3_EP_IN_SZ_MAX]; #endif #endif // CFG_TUD_AUDIO_ENABLE_EP_IN && (USE_LINEAR_BUFFER || CFG_TUD_AUDIO_ENABLE_DECODING) // EP OUT software buffers and mutexes #if CFG_TUD_AUDIO_ENABLE_EP_OUT && !CFG_TUD_AUDIO_ENABLE_DECODING #if CFG_TUD_AUDIO_FUNC_1_EP_OUT_SW_BUF_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_out_sw_buf_1[CFG_TUD_AUDIO_FUNC_1_EP_OUT_SW_BUF_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_out_sw_buf_1[CFG_TUD_AUDIO_FUNC_1_EP_OUT_SW_BUF_SZ]; #if CFG_FIFO_MUTEX osal_mutex_def_t ep_out_ff_mutex_rd_1; // No need for write mutex as only USB driver writes into FIFO #endif #endif // CFG_TUD_AUDIO_FUNC_1_EP_OUT_SW_BUF_SZ > 0 #if CFG_TUD_AUDIO > 1 && CFG_TUD_AUDIO_FUNC_2_EP_OUT_SW_BUF_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_out_sw_buf_2[CFG_TUD_AUDIO_FUNC_2_EP_OUT_SW_BUF_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_out_sw_buf_2[CFG_TUD_AUDIO_FUNC_2_EP_OUT_SW_BUF_SZ]; #if CFG_FIFO_MUTEX osal_mutex_def_t ep_out_ff_mutex_rd_2; // No need for write mutex as only USB driver writes into FIFO #endif #endif // CFG_TUD_AUDIO > 1 && CFG_TUD_AUDIO_FUNC_2_EP_OUT_SW_BUF_SZ > 0 #if CFG_TUD_AUDIO > 2 && CFG_TUD_AUDIO_FUNC_3_EP_OUT_SW_BUF_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_out_sw_buf_3[CFG_TUD_AUDIO_FUNC_3_EP_OUT_SW_BUF_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t audio_ep_out_sw_buf_3[CFG_TUD_AUDIO_FUNC_3_EP_OUT_SW_BUF_SZ]; #if CFG_FIFO_MUTEX osal_mutex_def_t ep_out_ff_mutex_rd_3; // No need for write mutex as only USB driver writes into FIFO #endif @@ -180,27 +180,27 @@ // - the software encoding is used - in this case the linear buffers serve as a target memory where logical channels are encoded into #if CFG_TUD_AUDIO_ENABLE_EP_OUT && (USE_LINEAR_BUFFER || CFG_TUD_AUDIO_ENABLE_DECODING) #if CFG_TUD_AUDIO_FUNC_1_EP_OUT_SZ_MAX > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_out_1[CFG_TUD_AUDIO_FUNC_1_EP_OUT_SZ_MAX]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_out_1[CFG_TUD_AUDIO_FUNC_1_EP_OUT_SZ_MAX]; #endif #if CFG_TUD_AUDIO > 1 && CFG_TUD_AUDIO_FUNC_2_EP_OUT_SZ_MAX > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_out_2[CFG_TUD_AUDIO_FUNC_2_EP_OUT_SZ_MAX]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_out_2[CFG_TUD_AUDIO_FUNC_2_EP_OUT_SZ_MAX]; #endif #if CFG_TUD_AUDIO > 2 && CFG_TUD_AUDIO_FUNC_3_EP_OUT_SZ_MAX > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_out_3[CFG_TUD_AUDIO_FUNC_3_EP_OUT_SZ_MAX]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t lin_buf_out_3[CFG_TUD_AUDIO_FUNC_3_EP_OUT_SZ_MAX]; #endif #endif // CFG_TUD_AUDIO_ENABLE_EP_OUT && (USE_LINEAR_BUFFER || CFG_TUD_AUDIO_ENABLE_DECODING) // Control buffers -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t ctrl_buf_1[CFG_TUD_AUDIO_FUNC_1_CTRL_BUF_SZ]; +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t ctrl_buf_1[CFG_TUD_AUDIO_FUNC_1_CTRL_BUF_SZ]; #if CFG_TUD_AUDIO > 1 -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t ctrl_buf_2[CFG_TUD_AUDIO_FUNC_2_CTRL_BUF_SZ]; +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t ctrl_buf_2[CFG_TUD_AUDIO_FUNC_2_CTRL_BUF_SZ]; #endif #if CFG_TUD_AUDIO > 2 -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t ctrl_buf_3[CFG_TUD_AUDIO_FUNC_3_CTRL_BUF_SZ]; +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t ctrl_buf_3[CFG_TUD_AUDIO_FUNC_3_CTRL_BUF_SZ]; #endif // Active alternate setting of interfaces @@ -217,7 +217,7 @@ uint8_t alt_setting_3[CFG_TUD_AUDIO_FUNC_3_N_AS_INT]; // Software encoding/decoding support FIFOs #if CFG_TUD_AUDIO_ENABLE_EP_IN && CFG_TUD_AUDIO_ENABLE_ENCODING #if CFG_TUD_AUDIO_FUNC_1_TX_SUPP_SW_FIFO_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t tx_supp_ff_buf_1[CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_1_TX_SUPP_SW_FIFO_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t tx_supp_ff_buf_1[CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_1_TX_SUPP_SW_FIFO_SZ]; tu_fifo_t tx_supp_ff_1[CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO]; #if CFG_FIFO_MUTEX osal_mutex_def_t tx_supp_ff_mutex_wr_1[CFG_TUD_AUDIO_FUNC_1_N_TX_SUPP_SW_FIFO]; // No need for read mutex as only USB driver reads from FIFO @@ -225,7 +225,7 @@ uint8_t alt_setting_3[CFG_TUD_AUDIO_FUNC_3_N_AS_INT]; #endif #if CFG_TUD_AUDIO > 1 && CFG_TUD_AUDIO_FUNC_2_TX_SUPP_SW_FIFO_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t tx_supp_ff_buf_2[CFG_TUD_AUDIO_FUNC_2_N_TX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_2_TX_SUPP_SW_FIFO_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t tx_supp_ff_buf_2[CFG_TUD_AUDIO_FUNC_2_N_TX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_2_TX_SUPP_SW_FIFO_SZ]; tu_fifo_t tx_supp_ff_2[CFG_TUD_AUDIO_FUNC_2_N_TX_SUPP_SW_FIFO]; #if CFG_FIFO_MUTEX osal_mutex_def_t tx_supp_ff_mutex_wr_2[CFG_TUD_AUDIO_FUNC_2_N_TX_SUPP_SW_FIFO]; // No need for read mutex as only USB driver reads from FIFO @@ -233,7 +233,7 @@ uint8_t alt_setting_3[CFG_TUD_AUDIO_FUNC_3_N_AS_INT]; #endif #if CFG_TUD_AUDIO > 2 && CFG_TUD_AUDIO_FUNC_3_TX_SUPP_SW_FIFO_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t tx_supp_ff_buf_3[CFG_TUD_AUDIO_FUNC_3_N_TX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_3_TX_SUPP_SW_FIFO_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t tx_supp_ff_buf_3[CFG_TUD_AUDIO_FUNC_3_N_TX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_3_TX_SUPP_SW_FIFO_SZ]; tu_fifo_t tx_supp_ff_3[CFG_TUD_AUDIO_FUNC_3_N_TX_SUPP_SW_FIFO]; #if CFG_FIFO_MUTEX osal_mutex_def_t tx_supp_ff_mutex_wr_3[CFG_TUD_AUDIO_FUNC_3_N_TX_SUPP_SW_FIFO]; // No need for read mutex as only USB driver reads from FIFO @@ -243,7 +243,7 @@ uint8_t alt_setting_3[CFG_TUD_AUDIO_FUNC_3_N_AS_INT]; #if CFG_TUD_AUDIO_ENABLE_EP_OUT && CFG_TUD_AUDIO_ENABLE_DECODING #if CFG_TUD_AUDIO_FUNC_1_RX_SUPP_SW_FIFO_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t rx_supp_ff_buf_1[CFG_TUD_AUDIO_FUNC_1_N_RX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_1_RX_SUPP_SW_FIFO_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t rx_supp_ff_buf_1[CFG_TUD_AUDIO_FUNC_1_N_RX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_1_RX_SUPP_SW_FIFO_SZ]; tu_fifo_t rx_supp_ff_1[CFG_TUD_AUDIO_FUNC_1_N_RX_SUPP_SW_FIFO]; #if CFG_FIFO_MUTEX osal_mutex_def_t rx_supp_ff_mutex_rd_1[CFG_TUD_AUDIO_FUNC_1_N_RX_SUPP_SW_FIFO]; // No need for write mutex as only USB driver writes into FIFO @@ -251,7 +251,7 @@ uint8_t alt_setting_3[CFG_TUD_AUDIO_FUNC_3_N_AS_INT]; #endif #if CFG_TUD_AUDIO > 1 && CFG_TUD_AUDIO_FUNC_2_RX_SUPP_SW_FIFO_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t rx_supp_ff_buf_2[CFG_TUD_AUDIO_FUNC_2_N_RX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_2_RX_SUPP_SW_FIFO_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t rx_supp_ff_buf_2[CFG_TUD_AUDIO_FUNC_2_N_RX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_2_RX_SUPP_SW_FIFO_SZ]; tu_fifo_t rx_supp_ff_2[CFG_TUD_AUDIO_FUNC_2_N_RX_SUPP_SW_FIFO]; #if CFG_FIFO_MUTEX osal_mutex_def_t rx_supp_ff_mutex_rd_2[CFG_TUD_AUDIO_FUNC_2_N_RX_SUPP_SW_FIFO]; // No need for write mutex as only USB driver writes into FIFO @@ -259,7 +259,7 @@ uint8_t alt_setting_3[CFG_TUD_AUDIO_FUNC_3_N_AS_INT]; #endif #if CFG_TUD_AUDIO > 2 && CFG_TUD_AUDIO_FUNC_3_RX_SUPP_SW_FIFO_SZ > 0 - CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t rx_supp_ff_buf_3[CFG_TUD_AUDIO_FUNC_3_N_RX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_3_RX_SUPP_SW_FIFO_SZ]; + CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN uint8_t rx_supp_ff_buf_3[CFG_TUD_AUDIO_FUNC_3_N_RX_SUPP_SW_FIFO][CFG_TUD_AUDIO_FUNC_3_RX_SUPP_SW_FIFO_SZ]; tu_fifo_t rx_supp_ff_3[CFG_TUD_AUDIO_FUNC_3_N_RX_SUPP_SW_FIFO]; #if CFG_FIFO_MUTEX osal_mutex_def_t rx_supp_ff_mutex_rd_3[CFG_TUD_AUDIO_FUNC_3_N_RX_SUPP_SW_FIFO]; // No need for write mutex as only USB driver writes into FIFO @@ -416,7 +416,7 @@ typedef struct //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -CFG_TUSB_MEM_SECTION audiod_function_t _audiod_fct[CFG_TUD_AUDIO]; +CFG_TUD_MEM_SECTION audiod_function_t _audiod_fct[CFG_TUD_AUDIO]; #if CFG_TUD_AUDIO_ENABLE_EP_OUT static bool audiod_rx_done_cb(uint8_t rhport, audiod_function_t* audio, uint16_t n_bytes_received); diff --git a/src/class/bth/bth_device.c b/src/class/bth/bth_device.c index f96bb3552..c5c74d26a 100755 --- a/src/class/bth/bth_device.c +++ b/src/class/bth/bth_device.c @@ -55,7 +55,7 @@ typedef struct //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -CFG_TUSB_MEM_SECTION btd_interface_t _btd_itf; +CFG_TUD_MEM_SECTION btd_interface_t _btd_itf; static bool bt_tx_data(uint8_t ep, void *data, uint16_t len) { diff --git a/src/class/cdc/cdc_device.c b/src/class/cdc/cdc_device.c index 5adce521d..f658df4d0 100644 --- a/src/class/cdc/cdc_device.c +++ b/src/class/cdc/cdc_device.c @@ -76,7 +76,7 @@ typedef struct //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -CFG_TUSB_MEM_SECTION tu_static cdcd_interface_t _cdcd_itf[CFG_TUD_CDC]; +CFG_TUD_MEM_SECTION tu_static cdcd_interface_t _cdcd_itf[CFG_TUD_CDC]; static bool _prep_out_transaction (cdcd_interface_t* p_cdc) { diff --git a/src/class/dfu/dfu_device.c b/src/class/dfu/dfu_device.c index 464c4bd6b..bffdb8376 100644 --- a/src/class/dfu/dfu_device.c +++ b/src/class/dfu/dfu_device.c @@ -56,7 +56,7 @@ typedef struct } dfu_state_ctx_t; // Only a single dfu state is allowed -CFG_TUSB_MEM_SECTION tu_static dfu_state_ctx_t _dfu_ctx; +CFG_TUD_MEM_SECTION tu_static dfu_state_ctx_t _dfu_ctx; static void reset_state(void) { diff --git a/src/class/hid/hid_device.c b/src/class/hid/hid_device.c index 9240fe2ca..5637ea6b4 100644 --- a/src/class/hid/hid_device.c +++ b/src/class/hid/hid_device.c @@ -58,7 +58,7 @@ typedef struct tusb_hid_descriptor_hid_t const * hid_descriptor; } hidd_interface_t; -CFG_TUSB_MEM_SECTION tu_static hidd_interface_t _hidd_itf[CFG_TUD_HID]; +CFG_TUD_MEM_SECTION tu_static hidd_interface_t _hidd_itf[CFG_TUD_HID]; /*------------- Helpers -------------*/ static inline uint8_t get_index_by_itfnum(uint8_t itf_num) diff --git a/src/class/midi/midi_device.c b/src/class/midi/midi_device.c index e3e7826da..052372a93 100644 --- a/src/class/midi/midi_device.c +++ b/src/class/midi/midi_device.c @@ -82,7 +82,7 @@ typedef struct //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -CFG_TUSB_MEM_SECTION midid_interface_t _midid_itf[CFG_TUD_MIDI]; +CFG_TUD_MEM_SECTION midid_interface_t _midid_itf[CFG_TUD_MIDI]; bool tud_midi_n_mounted (uint8_t itf) { diff --git a/src/class/msc/msc_device.c b/src/class/msc/msc_device.c index a409c4e27..a602e9672 100644 --- a/src/class/msc/msc_device.c +++ b/src/class/msc/msc_device.c @@ -74,8 +74,8 @@ typedef struct uint8_t add_sense_qualifier; }mscd_interface_t; -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static mscd_interface_t _mscd_itf; -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static uint8_t _mscd_buf[CFG_TUD_MSC_EP_BUFSIZE]; +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static mscd_interface_t _mscd_itf; +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static uint8_t _mscd_buf[CFG_TUD_MSC_EP_BUFSIZE]; //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION diff --git a/src/class/net/ecm_rndis_device.c b/src/class/net/ecm_rndis_device.c index 8ac7cbd01..762425732 100644 --- a/src/class/net/ecm_rndis_device.c +++ b/src/class/net/ecm_rndis_device.c @@ -61,10 +61,10 @@ typedef struct #define CFG_TUD_NET_PACKET_PREFIX_LEN sizeof(rndis_data_packet_t) #define CFG_TUD_NET_PACKET_SUFFIX_LEN 0 -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static uint8_t received[CFG_TUD_NET_PACKET_PREFIX_LEN + CFG_TUD_NET_MTU + CFG_TUD_NET_PACKET_PREFIX_LEN]; -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static uint8_t transmitted[CFG_TUD_NET_PACKET_PREFIX_LEN + CFG_TUD_NET_MTU + CFG_TUD_NET_PACKET_PREFIX_LEN]; struct ecm_notify_struct @@ -94,8 +94,8 @@ tu_static const struct ecm_notify_struct ecm_notify_csc = .uplink = 9728000, }; -// TODO remove CFG_TUSB_MEM_SECTION, control internal buffer is already in this special section -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static union +// TODO remove CFG_TUD_MEM_SECTION, control internal buffer is already in this special section +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static union { uint8_t rndis_buf[120]; struct ecm_notify_struct ecm_buf; @@ -104,8 +104,8 @@ CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static union //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -// TODO remove CFG_TUSB_MEM_SECTION -CFG_TUSB_MEM_SECTION tu_static netd_interface_t _netd_itf; +// TODO remove CFG_TUD_MEM_SECTION +CFG_TUD_MEM_SECTION tu_static netd_interface_t _netd_itf; tu_static bool can_xmit; diff --git a/src/class/net/ncm_device.c b/src/class/net/ncm_device.c index 9e9580249..611dc3348 100644 --- a/src/class/net/ncm_device.c +++ b/src/class/net/ncm_device.c @@ -130,7 +130,7 @@ typedef struct // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static const ntb_parameters_t ntb_parameters = { +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static const ntb_parameters_t ntb_parameters = { .wLength = sizeof(ntb_parameters_t), .bmNtbFormatsSupported = 0x01, .dwNtbInMaxSize = CFG_TUD_NCM_IN_NTB_MAX_SIZE, @@ -145,9 +145,9 @@ CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static const ntb_parameters_t ntb_par .wNtbOutMaxDatagrams = 0 }; -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static transmit_ntb_t transmit_ntb[2]; +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static transmit_ntb_t transmit_ntb[2]; -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static uint8_t receive_ntb[CFG_TUD_NCM_OUT_NTB_MAX_SIZE]; +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static uint8_t receive_ntb[CFG_TUD_NCM_OUT_NTB_MAX_SIZE]; tu_static ncm_interface_t ncm_interface; diff --git a/src/class/usbtmc/usbtmc_device.c b/src/class/usbtmc/usbtmc_device.c index 4e320a778..573654d58 100644 --- a/src/class/usbtmc/usbtmc_device.c +++ b/src/class/usbtmc/usbtmc_device.c @@ -143,7 +143,7 @@ typedef struct usbtmc_capabilities_specific_t const * capabilities; } usbtmc_interface_state_t; -CFG_TUSB_MEM_SECTION tu_static usbtmc_interface_state_t usbtmc_state = +CFG_TUD_MEM_SECTION tu_static usbtmc_interface_state_t usbtmc_state = { .itf_id = 0xFF, }; diff --git a/src/class/vendor/vendor_device.c b/src/class/vendor/vendor_device.c index 93596ee33..389a29696 100644 --- a/src/class/vendor/vendor_device.c +++ b/src/class/vendor/vendor_device.c @@ -59,7 +59,7 @@ typedef struct CFG_TUSB_MEM_ALIGN uint8_t epin_buf[CFG_TUD_VENDOR_EPSIZE]; } vendord_interface_t; -CFG_TUSB_MEM_SECTION tu_static vendord_interface_t _vendord_itf[CFG_TUD_VENDOR]; +CFG_TUD_MEM_SECTION tu_static vendord_interface_t _vendord_itf[CFG_TUD_VENDOR]; #define ITF_MEM_RESET_SIZE offsetof(vendord_interface_t, rx_ff) diff --git a/src/class/video/video_device.c b/src/class/video/video_device.c index 91f452afc..e6fadf41b 100644 --- a/src/class/video/video_device.c +++ b/src/class/video/video_device.c @@ -130,8 +130,8 @@ typedef struct TU_ATTR_PACKED { //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -CFG_TUSB_MEM_SECTION tu_static videod_interface_t _videod_itf[CFG_TUD_VIDEO]; -CFG_TUSB_MEM_SECTION tu_static videod_streaming_interface_t _videod_streaming_itf[CFG_TUD_VIDEO_STREAMING]; +CFG_TUD_MEM_SECTION tu_static videod_interface_t _videod_itf[CFG_TUD_VIDEO]; +CFG_TUD_MEM_SECTION tu_static videod_streaming_interface_t _videod_streaming_itf[CFG_TUD_VIDEO_STREAMING]; tu_static uint8_t const _cap_get = 0x1u; /* support for GET */ tu_static uint8_t const _cap_get_set = 0x3u; /* support for GET and SET */ diff --git a/src/device/usbd_control.c b/src/device/usbd_control.c index c580e6ecf..76d062e40 100644 --- a/src/device/usbd_control.c +++ b/src/device/usbd_control.c @@ -55,7 +55,7 @@ typedef struct tu_static usbd_control_xfer_t _ctrl_xfer; -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN tu_static uint8_t _usbd_ctrl_buf[CFG_TUD_ENDPOINT0_SIZE]; //--------------------------------------------------------------------+ diff --git a/src/portable/bridgetek/ft9xx/dcd_ft9xx.c b/src/portable/bridgetek/ft9xx/dcd_ft9xx.c index 95dfda49c..f02415904 100644 --- a/src/portable/bridgetek/ft9xx/dcd_ft9xx.c +++ b/src/portable/bridgetek/ft9xx/dcd_ft9xx.c @@ -51,7 +51,7 @@ extern int8_t board_ft9xx_vbus(void); extern int board_uart_write(void const *buf, int len); // Static array to store an incoming SETUP request for processing by tinyusb. -CFG_TUSB_MEM_SECTION CFG_TUSB_MEM_ALIGN +CFG_TUD_MEM_SECTION CFG_TUSB_MEM_ALIGN static uint8_t _ft9xx_setup_packet[8]; struct ft9xx_xfer_state diff --git a/src/portable/chipidea/ci_fs/dcd_ci_fs.c b/src/portable/chipidea/ci_fs/dcd_ci_fs.c index 37265df8b..9327e09d8 100644 --- a/src/portable/chipidea/ci_fs/dcd_ci_fs.c +++ b/src/portable/chipidea/ci_fs/dcd_ci_fs.c @@ -116,7 +116,7 @@ typedef struct // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ // BDT(Buffer Descriptor Table) must be 256-byte aligned -CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(512) static dcd_data_t _dcd; +CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(512) static dcd_data_t _dcd; TU_VERIFY_STATIC( sizeof(_dcd.bdt) == 512, "size is not correct" ); diff --git a/src/portable/chipidea/ci_hs/dcd_ci_hs.c b/src/portable/chipidea/ci_hs/dcd_ci_hs.c index f50550d33..f9ec666e5 100644 --- a/src/portable/chipidea/ci_hs/dcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/dcd_ci_hs.c @@ -175,7 +175,7 @@ typedef struct { dcd_qtd_t qtd[TUP_DCD_ENDPOINT_MAX][2] TU_ATTR_ALIGNED(32); }dcd_data_t; -CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(2048) +CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(2048) static dcd_data_t _dcd_data; //--------------------------------------------------------------------+ diff --git a/src/portable/microchip/pic/dcd_pic.c b/src/portable/microchip/pic/dcd_pic.c index 6986c8317..ccc27c3c9 100644 --- a/src/portable/microchip/pic/dcd_pic.c +++ b/src/portable/microchip/pic/dcd_pic.c @@ -189,7 +189,7 @@ typedef struct // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ // BDT(Buffer Descriptor Table) must be 256-byte aligned -CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(512) volatile static dcd_data_t _dcd; +CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(512) volatile static dcd_data_t _dcd; #if TU_PIC_INT_SIZE == 4 TU_VERIFY_STATIC( sizeof(_dcd.bdt) == 512, "size is not correct" ); diff --git a/src/portable/microchip/samx7x/dcd_samx7x.c b/src/portable/microchip/samx7x/dcd_samx7x.c index 2bbb345d6..9586df84d 100644 --- a/src/portable/microchip/samx7x/dcd_samx7x.c +++ b/src/portable/microchip/samx7x/dcd_samx7x.c @@ -77,7 +77,7 @@ static tusb_speed_t get_speed(void); static void dcd_transmit_packet(xfer_ctl_t * xfer, uint8_t ep_ix); // DMA descriptors shouldn't be placed in ITCM ! -CFG_TUSB_MEM_SECTION static dma_desc_t dma_desc[6]; +CFG_TUD_MEM_SECTION static dma_desc_t dma_desc[6]; static xfer_ctl_t xfer_status[EP_MAX]; diff --git a/src/portable/mindmotion/mm32/dcd_mm32f327x_otg.c b/src/portable/mindmotion/mm32/dcd_mm32f327x_otg.c index 39b09db68..c3d0c7297 100644 --- a/src/portable/mindmotion/mm32/dcd_mm32f327x_otg.c +++ b/src/portable/mindmotion/mm32/dcd_mm32f327x_otg.c @@ -110,7 +110,7 @@ typedef struct // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ // BDT(Buffer Descriptor Table) must be 256-byte aligned -CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(512) static dcd_data_t _dcd; +CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(512) static dcd_data_t _dcd; TU_VERIFY_STATIC( sizeof(_dcd.bdt) == 512, "size is not correct" ); diff --git a/src/portable/nxp/khci/dcd_khci.c b/src/portable/nxp/khci/dcd_khci.c index 52f4145f2..5c65ea33d 100644 --- a/src/portable/nxp/khci/dcd_khci.c +++ b/src/portable/nxp/khci/dcd_khci.c @@ -114,7 +114,7 @@ typedef struct // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ // BDT(Buffer Descriptor Table) must be 256-byte aligned -CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(512) static dcd_data_t _dcd; +CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(512) static dcd_data_t _dcd; TU_VERIFY_STATIC( sizeof(_dcd.bdt) == 512, "size is not correct" ); diff --git a/src/portable/nxp/lpc17_40/dcd_lpc17_40.c b/src/portable/nxp/lpc17_40/dcd_lpc17_40.c index 86149afd8..b880c2870 100644 --- a/src/portable/nxp/lpc17_40/dcd_lpc17_40.c +++ b/src/portable/nxp/lpc17_40/dcd_lpc17_40.c @@ -92,7 +92,7 @@ typedef struct } dcd_data_t; -CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(128) static dcd_data_t _dcd; +CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(128) static dcd_data_t _dcd; //--------------------------------------------------------------------+ diff --git a/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c b/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c index 5368ef868..7ca698a93 100644 --- a/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c +++ b/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c @@ -176,11 +176,11 @@ typedef struct // EP list must be 256-byte aligned // Some MCU controller may require this variable to be placed in specific SRAM region. // For example: LPC55s69 port1 Highspeed must be USB_RAM (0x40100000) -// Use CFG_TUSB_MEM_SECTION to place it accordingly. -CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(256) static dcd_data_t _dcd; +// Use CFG_TUD_MEM_SECTION to place it accordingly. +CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(256) static dcd_data_t _dcd; // Dummy buffer to fix ZLPs overwriting the buffer (probably an USB/DMA controller bug) -CFG_TUSB_MEM_SECTION TU_ATTR_ALIGNED(64) static uint8_t dummy[8]; +CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(64) static uint8_t dummy[8]; //--------------------------------------------------------------------+ // Multiple Controllers diff --git a/src/tusb_option.h b/src/tusb_option.h index c792efe6a..7a4cfe51c 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -295,15 +295,14 @@ #define CFG_TUSB_DEBUG 0 #endif -// TODO MEM_SECTION can be different for host and device controller -// should use CFG_TUD_MEM_SECTION, CFG_TUH_MEM_SECTION +// Memory section for placing buffer used for usb transferring. If MEM_SECTION is different for +// host and device use: CFG_TUD_MEM_SECTION, CFG_TUH_MEM_SECTION instead #ifndef CFG_TUSB_MEM_SECTION #define CFG_TUSB_MEM_SECTION #endif -// alignment requirement of buffer used for endpoint transferring -// TODO MEM_ALIGN can be different for host and device controller -// should use CFG_TUD_MEM_ALIGN, CFG_TUH_MEM_ALIGN +// Alignment requirement of buffer used for usb transferring. if MEM_ALIGN is different for +// host and device controller use: CFG_TUD_MEM_ALIGN, CFG_TUH_MEM_ALIGN instead #ifndef CFG_TUSB_MEM_ALIGN #define CFG_TUSB_MEM_ALIGN TU_ATTR_ALIGNED(4) #endif @@ -321,24 +320,14 @@ // Device Options (Default) //-------------------------------------------------------------------- -// Attribute to place data in accessible RAM for device controller -// default to CFG_TUSB_MEM_SECTION for backward-compatible +// Attribute to place data in accessible RAM for device controller (default: CFG_TUSB_MEM_SECTION) #ifndef CFG_TUD_MEM_SECTION - #ifdef CFG_TUSB_MEM_SECTION - #define CFG_TUD_MEM_SECTION CFG_TUSB_MEM_SECTION - #else - #define CFG_TUD_MEM_SECTION - #endif + #define CFG_TUD_MEM_SECTION CFG_TUSB_MEM_SECTION #endif -// Attribute to align memory for device controller -// default to CFG_TUSB_MEM_ALIGN for backward-compatible +// Attribute to align memory for device controller (default: CFG_TUSB_MEM_ALIGN) #ifndef CFG_TUD_MEM_ALIGN - #ifdef CFG_TUSB_MEM_ALIGN - #define CFG_TUD_MEM_ALIGN CFG_TUSB_MEM_ALIGN - #else - #define CFG_TUD_MEM_ALIGN TU_ATTR_ALIGNED(4) - #endif + #define CFG_TUD_MEM_ALIGN CFG_TUSB_MEM_ALIGN #endif #ifndef CFG_TUD_ENDPOINT0_SIZE @@ -419,23 +408,14 @@ #endif #endif // CFG_TUH_ENABLED -// Attribute to place data in accessible RAM for host controller -// default to CFG_TUSB_MEM_SECTION for backward-compatible +// Attribute to place data in accessible RAM for host controller (default: CFG_TUSB_MEM_SECTION) #ifndef CFG_TUH_MEM_SECTION - #ifdef CFG_TUSB_MEM_SECTION - #define CFG_TUH_MEM_SECTION CFG_TUSB_MEM_SECTION - #else - #define CFG_TUH_MEM_SECTION - #endif + #define CFG_TUH_MEM_SECTION CFG_TUSB_MEM_SECTION #endif // Attribute to align memory for host controller #ifndef CFG_TUH_MEM_ALIGN - #ifdef CFG_TUSB_MEM_ALIGN - #define CFG_TUH_MEM_ALIGN CFG_TUSB_MEM_ALIGN - #else - #define CFG_TUH_MEM_ALIGN TU_ATTR_ALIGNED(4) - #endif + #define CFG_TUH_MEM_ALIGN CFG_TUSB_MEM_ALIGN #endif //------------- CLASS -------------// -- cgit v1.3.1 From 14a7379799418c6e8ffb7231ee1703a0f95665da Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 24 Jul 2023 16:54:02 +0700 Subject: fix ohci warnings, and add freertosconfig for lpc4088 --- hw/bsp/lpc40/FreeRTOSConfig/FreeRTOSConfig.h | 165 +++++++++++++++++++++++++++ hw/bsp/lpc40/family.cmake | 2 + src/portable/ohci/ohci.c | 25 ++-- 3 files changed, 182 insertions(+), 10 deletions(-) create mode 100644 hw/bsp/lpc40/FreeRTOSConfig/FreeRTOSConfig.h (limited to 'src/portable') diff --git a/hw/bsp/lpc40/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/lpc40/FreeRTOSConfig/FreeRTOSConfig.h new file mode 100644 index 000000000..96611ca1c --- /dev/null +++ b/hw/bsp/lpc40/FreeRTOSConfig/FreeRTOSConfig.h @@ -0,0 +1,165 @@ +/* + * FreeRTOS Kernel V10.0.0 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. If you wish to use our Amazon + * FreeRTOS name, please do so in a fair use way that does not cause confusion. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + + +#ifndef FREERTOS_CONFIG_H +#define FREERTOS_CONFIG_H + +/*----------------------------------------------------------- + * Application specific definitions. + * + * These definitions should be adjusted for your particular hardware and + * application requirements. + * + * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE + * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. + * + * See http://www.freertos.org/a00110.html. + *----------------------------------------------------------*/ + +// skip if included from IAR assembler +#ifndef __IASMARM__ + #include "chip.h" +#endif + +/* Cortex M23/M33 port configuration. */ +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) + +#define configUSE_PREEMPTION 1 +#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 +#define configCPU_CLOCK_HZ SystemCoreClock +#define configTICK_RATE_HZ ( 1000 ) +#define configMAX_PRIORITIES ( 5 ) +#define configMINIMAL_STACK_SIZE ( 128 ) +#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) +#define configMAX_TASK_NAME_LEN 16 +#define configUSE_16_BIT_TICKS 0 +#define configIDLE_SHOULD_YIELD 1 +#define configUSE_MUTEXES 1 +#define configUSE_RECURSIVE_MUTEXES 1 +#define configUSE_COUNTING_SEMAPHORES 1 +#define configQUEUE_REGISTRY_SIZE 2 +#define configUSE_QUEUE_SETS 0 +#define configUSE_TIME_SLICING 0 +#define configUSE_NEWLIB_REENTRANT 0 +#define configENABLE_BACKWARD_COMPATIBILITY 1 +#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 + +#define configSUPPORT_STATIC_ALLOCATION 0 +#define configSUPPORT_DYNAMIC_ALLOCATION 1 + +/* Hook function related definitions. */ +#define configUSE_IDLE_HOOK 0 +#define configUSE_TICK_HOOK 0 +#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning +#define configCHECK_FOR_STACK_OVERFLOW 2 + +/* Run time and task stats gathering related definitions. */ +#define configGENERATE_RUN_TIME_STATS 0 +#define configRECORD_STACK_HIGH_ADDRESS 1 +#define configUSE_TRACE_FACILITY 1 // legacy trace +#define configUSE_STATS_FORMATTING_FUNCTIONS 0 + +/* Co-routine definitions. */ +#define configUSE_CO_ROUTINES 0 +#define configMAX_CO_ROUTINE_PRIORITIES 2 + +/* Software timer related definitions. */ +#define configUSE_TIMERS 1 +#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) +#define configTIMER_QUEUE_LENGTH 32 +#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE + +/* Optional functions - most linkers will remove unused functions anyway. */ +#define INCLUDE_vTaskPrioritySet 0 +#define INCLUDE_uxTaskPriorityGet 0 +#define INCLUDE_vTaskDelete 0 +#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY +#define INCLUDE_xResumeFromISR 0 +#define INCLUDE_vTaskDelayUntil 1 +#define INCLUDE_vTaskDelay 1 +#define INCLUDE_xTaskGetSchedulerState 0 +#define INCLUDE_xTaskGetCurrentTaskHandle 1 +#define INCLUDE_uxTaskGetStackHighWaterMark 0 +#define INCLUDE_xTaskGetIdleTaskHandle 0 +#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 +#define INCLUDE_pcTaskGetTaskName 0 +#define INCLUDE_eTaskGetState 0 +#define INCLUDE_xEventGroupSetBitFromISR 0 +#define INCLUDE_xTimerPendFunctionCall 0 + +/* Define to trap errors during development. */ +// Halt CPU (breakpoint) when hitting error, only apply for Cortex M3, M4, M7 +#if defined(__ARM_ARCH_7M__) || defined (__ARM_ARCH_7EM__) + #define configASSERT(_exp) \ + do {\ + if ( !(_exp) ) { \ + volatile uint32_t* ARM_CM_DHCSR = ((volatile uint32_t*) 0xE000EDF0UL); /* Cortex M CoreDebug->DHCSR */ \ + if ( (*ARM_CM_DHCSR) & 1UL ) { /* Only halt mcu if debugger is attached */ \ + taskDISABLE_INTERRUPTS(); \ + __asm("BKPT #0\n"); \ + }\ + }\ + } while(0) +#else + #define configASSERT( x ) +#endif + +/* FreeRTOS hooks to NVIC vectors */ +#define xPortPendSVHandler PendSV_Handler +#define xPortSysTickHandler SysTick_Handler +#define vPortSVCHandler SVC_Handler + +//--------------------------------------------------------------------+ +// Interrupt nesting behavior configuration. +//--------------------------------------------------------------------+ + +// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header +#define configPRIO_BITS 5 + +/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1<is_interrupt_xfer = (xfer_type == TUSB_XFER_INTERRUPT ? 1 : 0); } -static void gtd_init(ohci_gtd_t* p_td, uint8_t* data_ptr, uint16_t total_bytes) -{ +static void gtd_init(ohci_gtd_t *p_td, uint8_t *data_ptr, uint16_t total_bytes) { tu_memclr(p_td, sizeof(ohci_gtd_t)); - p_td->used = 1; - p_td->expected_bytes = total_bytes; + p_td->used = 1; + p_td->expected_bytes = total_bytes; + + p_td->buffer_rounding = 1; // less than queued length is not a error + p_td->delay_interrupt = OHCI_INT_ON_COMPLETE_NO; + p_td->condition_code = OHCI_CCODE_NOT_ACCESSED; - p_td->buffer_rounding = 1; // less than queued length is not a error - p_td->delay_interrupt = OHCI_INT_ON_COMPLETE_NO; - p_td->condition_code = OHCI_CCODE_NOT_ACCESSED; + uint8_t *cbp = (uint8_t *) _phys_addr(data_ptr); - p_td->current_buffer_pointer = _phys_addr(data_ptr); - p_td->buffer_end = total_bytes ? (_phys_addr(data_ptr + total_bytes - 1)) : (uint8_t *)p_td->current_buffer_pointer; + p_td->current_buffer_pointer = cbp; + if ( total_bytes ) { + p_td->buffer_end = _phys_addr(data_ptr + total_bytes - 1); + } else { + p_td->buffer_end = cbp; + } } static ohci_ed_t * ed_from_addr(uint8_t dev_addr, uint8_t ep_addr) @@ -487,7 +492,7 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet ohci_ed_t* ed = &ohci_data.control[dev_addr].ed; ohci_gtd_t *qtd = &ohci_data.control[dev_addr].gtd; - gtd_init(qtd, (uint8_t*) setup_packet, 8); + gtd_init(qtd, (uint8_t*)(uintptr_t) setup_packet, 8); qtd->index = dev_addr; qtd->pid = PID_SETUP; qtd->data_toggle = GTD_DT_DATA0; -- cgit v1.3.1 From d2542560470de242dd8988d0b3c10d7df0496bb0 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 24 Jul 2023 17:54:24 +0700 Subject: change dcache clean/invalidate return type to bool add tu_assert() check for aligned 32byte address for imxrt --- src/common/tusb_common.h | 13 +++++++------ src/host/hcd.h | 8 ++++---- src/portable/chipidea/ci_hs/ci_hs_imxrt.h | 15 +++++++++------ src/portable/chipidea/ci_hs/hcd_ci_hs.c | 12 ++++++------ src/portable/ehci/ehci.c | 9 ++++++--- 5 files changed, 32 insertions(+), 25 deletions(-) (limited to 'src/portable') diff --git a/src/common/tusb_common.h b/src/common/tusb_common.h index 957491aa9..bae583c06 100644 --- a/src/common/tusb_common.h +++ b/src/common/tusb_common.h @@ -99,10 +99,9 @@ TU_ATTR_WEAK extern void* tusb_app_phys_to_virt(void *phys_addr); #define tu_varclr(_var) tu_memclr(_var, sizeof(*(_var))) // This is a backport of memset_s from c11 -TU_ATTR_ALWAYS_INLINE static inline int tu_memset_s(void *dest, size_t destsz, int ch, size_t count) -{ +TU_ATTR_ALWAYS_INLINE static inline int tu_memset_s(void *dest, size_t destsz, int ch, size_t count) { // TODO may check if desst and src is not NULL - if (count > destsz) { + if ( count > destsz ) { return -1; } memset(dest, ch, count); @@ -110,10 +109,9 @@ TU_ATTR_ALWAYS_INLINE static inline int tu_memset_s(void *dest, size_t destsz, i } // This is a backport of memcpy_s from c11 -TU_ATTR_ALWAYS_INLINE static inline int tu_memcpy_s(void *dest, size_t destsz, const void * src, size_t count ) -{ +TU_ATTR_ALWAYS_INLINE static inline int tu_memcpy_s(void *dest, size_t destsz, const void *src, size_t count) { // TODO may check if desst and src is not NULL - if (count > destsz) { + if ( count > destsz ) { return -1; } memcpy(dest, src, count); @@ -169,6 +167,9 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_align32 (uint32_t value) { retur TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_align4k (uint32_t value) { return (value & 0xFFFFF000UL); } TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_offset4k(uint32_t value) { return (value & 0xFFFUL); } +TU_ATTR_ALWAYS_INLINE static inline bool tu_is_aligned32(uint32_t value) { return (value & 0x1FUL) == 0; } +TU_ATTR_ALWAYS_INLINE static inline bool tu_is_aligned64(uint64_t value) { return (value & 0x3FUL) == 0; } + //------------- Mathematics -------------// TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_div_ceil(uint32_t v, uint32_t d) { return (v + d -1)/d; } diff --git a/src/host/hcd.h b/src/host/hcd.h index 3355c18b2..52fcc834e 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -104,21 +104,21 @@ typedef struct uint8_t speed; } hcd_devtree_info_t; -//--------------------------------------------------------------------+ +//-------------------------------------------------------------- // Memory API //--------------------------------------------------------------------+ // clean/flush data cache: write cache -> memory. // Required before an DMA TX transfer to make sure data is in memory -void hcd_dcache_clean(void const* addr, uint32_t data_size) TU_ATTR_WEAK; +bool hcd_dcache_clean(void const* addr, uint32_t data_size) TU_ATTR_WEAK; // invalidate data cache: mark cache as invalid, next read will read from memory // Required BOTH before and after an DMA RX transfer -void hcd_dcache_invalidate(void const* addr, uint32_t data_size) TU_ATTR_WEAK; +bool hcd_dcache_invalidate(void const* addr, uint32_t data_size) TU_ATTR_WEAK; // clean and invalidate data cache // Required before an DMA transfer where memory is both read/write by DMA -void hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) TU_ATTR_WEAK; +bool hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) TU_ATTR_WEAK; //--------------------------------------------------------------------+ // Controller API diff --git a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h index 96f0ba766..c59c107ff 100644 --- a/src/portable/chipidea/ci_hs/ci_hs_imxrt.h +++ b/src/portable/chipidea/ci_hs/ci_hs_imxrt.h @@ -68,31 +68,34 @@ TU_ATTR_ALWAYS_INLINE static inline bool imxrt_is_cache_mem(uintptr_t addr) { return !(0x20000000 <= addr && addr < 0x20100000); } -TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_clean(void const* addr, uint32_t data_size) { +TU_ATTR_ALWAYS_INLINE static inline bool imxrt_dcache_clean(void const* addr, uint32_t data_size) { const uintptr_t addr32 = (uintptr_t) addr; if (imxrt_is_cache_mem(addr32)) { + TU_ASSERT(tu_is_aligned32(addr32)); SCB_CleanDCache_by_Addr((uint32_t *) addr32, (int32_t) data_size); } + return true; } -TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_invalidate(void const* addr, uint32_t data_size) { +TU_ATTR_ALWAYS_INLINE static inline bool imxrt_dcache_invalidate(void const* addr, uint32_t data_size) { const uintptr_t addr32 = (uintptr_t) addr; if (imxrt_is_cache_mem(addr32)) { // Invalidating does not push cached changes back to RAM so we need to be // *very* careful when we do it. If we're not aligned, then we risk resetting // values back to their RAM state. - // if (addr32 % 32 != 0) { - // TU_BREAKPOINT(); - // } + TU_ASSERT(tu_is_aligned32(addr32)); SCB_InvalidateDCache_by_Addr((void*) addr32, (int32_t) data_size); } + return true; } -TU_ATTR_ALWAYS_INLINE static inline void imxrt_dcache_clean_invalidate(void const* addr, uint32_t data_size) { +TU_ATTR_ALWAYS_INLINE static inline bool imxrt_dcache_clean_invalidate(void const* addr, uint32_t data_size) { const uintptr_t addr32 = (uintptr_t) addr; if (imxrt_is_cache_mem(addr32)) { + TU_ASSERT(tu_is_aligned32(addr32)); SCB_CleanInvalidateDCache_by_Addr((uint32_t *) addr32, (int32_t) data_size); } + return true; } #endif diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index 56167b8f6..6ee91e18e 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -41,16 +41,16 @@ #if CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX #include "ci_hs_imxrt.h" - void hcd_dcache_clean(void const* addr, uint32_t data_size) { - imxrt_dcache_clean(addr, data_size); + bool hcd_dcache_clean(void const* addr, uint32_t data_size) { + return imxrt_dcache_clean(addr, data_size); } - void hcd_dcache_invalidate(void const* addr, uint32_t data_size) { - imxrt_dcache_invalidate(addr, data_size); + bool hcd_dcache_invalidate(void const* addr, uint32_t data_size) { + return imxrt_dcache_invalidate(addr, data_size); } - void hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { - imxrt_dcache_clean_invalidate(addr, data_size); + bool hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { + return imxrt_dcache_clean_invalidate(addr, data_size); } #elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 38711e382..6dfaab2a2 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -162,16 +162,19 @@ static void qtd_init (ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes) static inline void list_insert (ehci_link_t *current, ehci_link_t *new, uint8_t new_type); static inline ehci_link_t* list_next (ehci_link_t const *p_link); -TU_ATTR_WEAK void hcd_dcache_clean(void const* addr, uint32_t data_size) { +TU_ATTR_WEAK bool hcd_dcache_clean(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; + return true; } -TU_ATTR_WEAK void hcd_dcache_invalidate(void const* addr, uint32_t data_size) { +TU_ATTR_WEAK bool hcd_dcache_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; + return true; } -TU_ATTR_WEAK void hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { +TU_ATTR_WEAK bool hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { (void) addr; (void) data_size; + return true; } //--------------------------------------------------------------------+ -- cgit v1.3.1 From f295aaf1851eb270070af7292d1f100f7172daf4 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 24 Jul 2023 11:55:54 +0700 Subject: add hcd abort xfer for rp2040 pio usb --- hw/bsp/rp2040/board.h | 12 ++++++------ src/portable/raspberrypi/pio_usb/hcd_pio_usb.c | 7 ++----- tools/get_deps.py | 2 +- 3 files changed, 9 insertions(+), 12 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/rp2040/board.h b/hw/bsp/rp2040/board.h index 934e1c7ae..063c9580e 100644 --- a/hw/bsp/rp2040/board.h +++ b/hw/bsp/rp2040/board.h @@ -54,19 +54,19 @@ // default to pin on Adafruit Feather rp2040 USB Host or Tester if defined //--------------------------------------------------------------------+ -// #define USE_ADAFRUIT_RP2040_TESTER -#ifdef USE_ADAFRUIT_RP2040_TESTER -#define PICO_DEFAULT_PIO_USB_DP_PIN 20 -#define PICO_DEFAULT_PIO_USB_VBUSEN_PIN 22 +// #define USE_ADAFRUIT_FEATHER_RP2040_USBHOST +#ifdef USE_ADAFRUIT_FEATHER_RP2040_USBHOST +#define PICO_DEFAULT_PIO_USB_DP_PIN 16 +#define PICO_DEFAULT_PIO_USB_VBUSEN_PIN 18 #endif #ifndef PICO_DEFAULT_PIO_USB_DP_PIN -#define PICO_DEFAULT_PIO_USB_DP_PIN 16 +#define PICO_DEFAULT_PIO_USB_DP_PIN 20 #endif // VBUS enable pin and its active state #ifndef PICO_DEFAULT_PIO_USB_VBUSEN_PIN -#define PICO_DEFAULT_PIO_USB_VBUSEN_PIN 18 +#define PICO_DEFAULT_PIO_USB_VBUSEN_PIN 22 #endif // VBUS enable state diff --git a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c index fa285327c..bb41ad638 100644 --- a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c +++ b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c @@ -139,11 +139,8 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * } bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { - (void) rhport; - (void) dev_addr; - (void) ep_addr; - // TODO not implemented yet - return false; + uint8_t const pio_rhport = RHPORT_PIO(rhport); + return pio_usb_host_endpoint_abort_transfer(pio_rhport, dev_addr, ep_addr); } bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) diff --git a/tools/get_deps.py b/tools/get_deps.py index 9b89c5e4c..d6505a1d9 100644 --- a/tools/get_deps.py +++ b/tools/get_deps.py @@ -54,7 +54,7 @@ deps_optional = { '950819b7de9b32f92c3edf396bc5ffb8d66e7009', 'kinetis_k32l2 kinetis_kl lpc51 lpc54 lpc55 mcx imxrt'], 'hw/mcu/raspberry_pi/Pico-PIO-USB': ['https://github.com/sekigon-gonnoc/Pico-PIO-USB.git', - '58879cfa0eca5725d8db6443ec17f8896a321042', + 'd00a10a8c425d0d40f81b87169102944b01f3bb3', 'rp2040'], 'hw/mcu/renesas/fsp': ['https://github.com/renesas/fsp.git', '8dc14709f2a6518b43f71efad70d900b7718d9f1', -- cgit v1.3.1 From ef69da054e4d373636818a52df4e3433152fa3bf Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 25 Jul 2023 12:03:54 +0700 Subject: use standard EHCI USB INT instead of chipidea async/period interrupt to be compatible with other EHCI implementation --- src/portable/ehci/ehci.c | 24 ++++++++---------------- src/portable/ehci/ehci.h | 6 +----- 2 files changed, 9 insertions(+), 21 deletions(-) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 241393a39..a9e184f22 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -307,8 +307,8 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) regs->status = (EHCI_INT_MASK_ALL & ~EHCI_INT_MASK_PORT_CHANGE); // Enable interrupts - regs->inten = EHCI_INT_MASK_ERROR | EHCI_INT_MASK_PORT_CHANGE | EHCI_INT_MASK_ASYNC_ADVANCE | - EHCI_INT_MASK_NXP_PERIODIC | EHCI_INT_MASK_NXP_ASYNC | EHCI_INT_MASK_FRAMELIST_ROLLOVER; + regs->inten = EHCI_INT_MASK_USB | EHCI_INT_MASK_ERROR | EHCI_INT_MASK_PORT_CHANGE | + EHCI_INT_MASK_ASYNC_ADVANCE | EHCI_INT_MASK_FRAMELIST_ROLLOVER; //------------- Asynchronous List -------------// ehci_qhd_t * const async_head = list_get_async_head(rhport); @@ -768,28 +768,20 @@ void hcd_int_handler(uint8_t rhport) regs->status = EHCI_INT_MASK_PORT_CHANGE; // Acknowledge } + // A USB transfer is completed with error if (int_status & EHCI_INT_MASK_ERROR) { xfer_error_isr(rhport); regs->status = EHCI_INT_MASK_ERROR; // Acknowledge } - //------------- some QTD/SITD/ITD with IOC set is completed -------------// - if (int_status & EHCI_INT_MASK_NXP_ASYNC) { - async_list_xfer_complete_isr(list_get_async_head(rhport)); - regs->status = EHCI_INT_MASK_NXP_ASYNC; // Acknowledge - } - - if (int_status & EHCI_INT_MASK_NXP_PERIODIC) - { - for (uint32_t i=1; i <= FRAMELIST_SIZE; i *= 2) - { + // A USB transfer is completed + if (int_status & EHCI_INT_MASK_USB) { + for ( uint32_t i = 1; i <= FRAMELIST_SIZE; i *= 2 ) { period_list_xfer_complete_isr(rhport, i); } - regs->status = EHCI_INT_MASK_NXP_PERIODIC; // Acknowledge - } - if (int_status & EHCI_INT_MASK_USB) { - // TODO standard EHCI xfer complete + async_list_xfer_complete_isr(list_get_async_head(rhport)); + regs->status = EHCI_INT_MASK_USB; // Acknowledge } diff --git a/src/portable/ehci/ehci.h b/src/portable/ehci/ehci.h index 05de80539..457adc1d3 100644 --- a/src/portable/ehci/ehci.h +++ b/src/portable/ehci/ehci.h @@ -278,14 +278,10 @@ enum { EHCI_INT_MASK_PERIODIC_SCHED_STATUS = TU_BIT(14), EHCI_INT_MASK_ASYNC_SCHED_STATUS = TU_BIT(15), - EHCI_INT_MASK_NXP_ASYNC = TU_BIT(18), - EHCI_INT_MASK_NXP_PERIODIC = TU_BIT(19), - EHCI_INT_MASK_ALL = EHCI_INT_MASK_USB | EHCI_INT_MASK_ERROR | EHCI_INT_MASK_PORT_CHANGE | EHCI_INT_MASK_FRAMELIST_ROLLOVER | EHCI_INT_MASK_PCI_HOST_SYSTEM_ERROR | - EHCI_INT_MASK_ASYNC_ADVANCE | EHCI_INT_MASK_NXP_SOF | - EHCI_INT_MASK_NXP_ASYNC | EHCI_INT_MASK_NXP_PERIODIC + EHCI_INT_MASK_ASYNC_ADVANCE | EHCI_INT_MASK_NXP_SOF }; enum { -- cgit v1.3.1 From 4deea875793ce78a24b069491bb83e59e310c476 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 25 Jul 2023 15:07:21 +0700 Subject: improve processing usb complete and error isr. also merge them together --- hw/bsp/imxrt/family.cmake | 120 ++++++++++++------------ src/CMakeLists.txt | 1 + src/portable/ehci/ehci.c | 228 ++++++++++++---------------------------------- 3 files changed, 120 insertions(+), 229 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/imxrt/family.cmake b/hw/bsp/imxrt/family.cmake index f1c5b0ab1..96ed4b030 100644 --- a/hw/bsp/imxrt/family.cmake +++ b/hw/bsp/imxrt/family.cmake @@ -22,69 +22,71 @@ set(FAMILY_MCUS MIMXRT1XXX CACHE INTERNAL "") #------------------------------------ # only need to be built ONCE for all examples function(add_board_target BOARD_TARGET) - if (NOT TARGET ${BOARD_TARGET}) - add_library(${BOARD_TARGET} STATIC - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD}/board/clock_config.c - #${SDK_DIR}/drivers/adc_12b1msps_sar/fsl_adc.c - ${SDK_DIR}/drivers/common/fsl_common.c - ${SDK_DIR}/drivers/igpio/fsl_gpio.c - ${SDK_DIR}/drivers/lpspi/fsl_lpspi.c - ${SDK_DIR}/drivers/lpuart/fsl_lpuart.c - ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_VARIANT}.c - ${SDK_DIR}/devices/${MCU_VARIANT}/xip/fsl_flexspi_nor_boot.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c - ) - target_compile_definitions(${BOARD_TARGET} PUBLIC - __ARMVFP__=0 - __ARMFPV5__=0 - XIP_EXTERNAL_FLASH=1 - XIP_BOOT_HEADER_ENABLE=1 - ) - target_include_directories(${BOARD_TARGET} PUBLIC - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD}/board - ${CMSIS_DIR}/CMSIS/Core/Include - ${SDK_DIR}/devices/${MCU_VARIANT} - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers - #${SDK_DIR}/drivers/adc_12b1msps_sar - ${SDK_DIR}/drivers/common - ${SDK_DIR}/drivers/igpio - ${SDK_DIR}/drivers/lpspi - ${SDK_DIR}/drivers/lpuart - ) + if (TARGET ${BOARD_TARGET}) + return() + endif () - update_board(${BOARD_TARGET}) + add_library(${BOARD_TARGET} STATIC + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD}/board/clock_config.c + #${SDK_DIR}/drivers/adc_12b1msps_sar/fsl_adc.c + ${SDK_DIR}/drivers/common/fsl_common.c + ${SDK_DIR}/drivers/igpio/fsl_gpio.c + ${SDK_DIR}/drivers/lpspi/fsl_lpspi.c + ${SDK_DIR}/drivers/lpuart/fsl_lpuart.c + ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_VARIANT}.c + ${SDK_DIR}/devices/${MCU_VARIANT}/xip/fsl_flexspi_nor_boot.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c + ) + target_compile_definitions(${BOARD_TARGET} PUBLIC + __ARMVFP__=0 + __ARMFPV5__=0 + XIP_EXTERNAL_FLASH=1 + XIP_BOOT_HEADER_ENABLE=1 + ) + target_include_directories(${BOARD_TARGET} PUBLIC + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD}/board + ${CMSIS_DIR}/CMSIS/Core/Include + ${SDK_DIR}/devices/${MCU_VARIANT} + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers + #${SDK_DIR}/drivers/adc_12b1msps_sar + ${SDK_DIR}/drivers/common + ${SDK_DIR}/drivers/igpio + ${SDK_DIR}/drivers/lpspi + ${SDK_DIR}/drivers/lpuart + ) - # LD_FILE and STARTUP_FILE can be defined in board.cmake - if (NOT DEFINED LD_FILE_${CMAKE_C_COMPILER_ID}) - set(LD_FILE_GNU ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_VARIANT}xxxxx_flexspi_nor.ld) - #set(LD_FILE_IAR ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_VARIANT}xxxxx_flexspi_nor.ld) - endif () + update_board(${BOARD_TARGET}) - if (NOT DEFINED STARTUP_FILE_${CMAKE_C_COMPILER_ID}) - set(STARTUP_FILE_GNU ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_VARIANT}.S) - #set(STARTUP_FILE_IAR ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_VARIANT}.S) - endif () + # LD_FILE and STARTUP_FILE can be defined in board.cmake + if (NOT DEFINED LD_FILE_${CMAKE_C_COMPILER_ID}) + set(LD_FILE_GNU ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_VARIANT}xxxxx_flexspi_nor.ld) + #set(LD_FILE_IAR ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_VARIANT}xxxxx_flexspi_nor.ld) + endif () - target_sources(${BOARD_TARGET} PUBLIC - ${STARTUP_FILE_${CMAKE_C_COMPILER_ID}} - ) + if (NOT DEFINED STARTUP_FILE_${CMAKE_C_COMPILER_ID}) + set(STARTUP_FILE_GNU ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_VARIANT}.S) + #set(STARTUP_FILE_IAR ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_VARIANT}.S) + endif () - if (CMAKE_C_COMPILER_ID STREQUAL "GNU") - target_link_options(${BOARD_TARGET} PUBLIC - "LINKER:--script=${LD_FILE_GNU}" - # nanolib - --specs=nosys.specs - --specs=nano.specs - # force linker to look for these symbols - -Wl,-uimage_vector_table - -Wl,-ug_boot_data - ) - elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") - target_link_options(${BOARD_TARGET} PUBLIC - "LINKER:--config=${LD_FILE_IAR}" - ) - endif () + target_sources(${BOARD_TARGET} PUBLIC + ${STARTUP_FILE_${CMAKE_C_COMPILER_ID}} + ) + + if (CMAKE_C_COMPILER_ID STREQUAL "GNU") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--script=${LD_FILE_GNU}" + # nanolib + --specs=nosys.specs + --specs=nano.specs + # force linker to look for these symbols + -Wl,-uimage_vector_table + -Wl,-ug_boot_data + ) + elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--config=${LD_FILE_IAR}" + ) endif () endfunction() @@ -114,7 +116,7 @@ function(family_configure_example TARGET RTOS) # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_MIMXRT1XXX ${RTOS}) - target_sources(${TARGET}-tinyusb PUBLIC + target_sources(${TARGET}-tinyusb PRIVATE ${TOP}/src/portable/chipidea/ci_hs/dcd_ci_hs.c ${TOP}/src/portable/chipidea/ci_hs/hcd_ci_hs.c ${TOP}/src/portable/ehci/ehci.c diff --git a/src/CMakeLists.txt b/src/CMakeLists.txt index 8f7f38589..076e1e1eb 100644 --- a/src/CMakeLists.txt +++ b/src/CMakeLists.txt @@ -64,6 +64,7 @@ function(add_tinyusb TARGET) -Wnull-dereference -Wuninitialized -Wunused + -Wunused-function -Wreturn-type -Wredundant-decls ) diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index a9e184f22..b84de5191 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -314,11 +314,11 @@ bool ehci_init(uint8_t rhport, uint32_t capability_reg, uint32_t operatial_reg) ehci_qhd_t * const async_head = list_get_async_head(rhport); tu_memclr(async_head, sizeof(ehci_qhd_t)); - async_head->next.address = (uint32_t) async_head; // circular list, next is itself - async_head->next.type = EHCI_QTYPE_QHD; - async_head->head_list_flag = 1; - async_head->qtd_overlay.halted = 1; // inactive most of time - async_head->qtd_overlay.next.terminate = 1; // TODO removed if verified + async_head->next.address = (uint32_t) async_head; // circular list, next is itself + async_head->next.type = EHCI_QTYPE_QHD; + async_head->head_list_flag = 1; + async_head->qtd_overlay.halted = 1; // inactive most of time + async_head->qtd_overlay.next.terminate = 1; // TODO removed if verified regs->async_list_addr = (uint32_t) async_head; @@ -533,70 +533,74 @@ void async_advance_isr(uint8_t rhport) } TU_ATTR_ALWAYS_INLINE static inline -void port_connect_status_change_isr(uint8_t rhport) -{ +void port_connect_status_change_isr(uint8_t rhport) { // NOTE There is an sequence plug->unplug->…..-> plug if device is powering with pre-plugged device - if (ehci_data.regs->portsc_bm.current_connect_status) - { + if ( ehci_data.regs->portsc_bm.current_connect_status ) { hcd_port_reset(rhport); hcd_event_device_attach(rhport, true); - }else // device unplugged + } else // device unplugged { hcd_event_device_remove(rhport, true); } } +// Check queue head for potential transfer complete (successful or error) TU_ATTR_ALWAYS_INLINE static inline void qhd_xfer_complete_isr(ehci_qhd_t * qhd) { - // examine TD attached to queue head - ehci_qtd_t * volatile qtd = qhd->attached_qtd; + hcd_dcache_invalidate(qhd, sizeof(ehci_qhd_t)); // HC may have updated the overlay + volatile ehci_qtd_t *qtd_overlay = &qhd->qtd_overlay; - if (qtd == NULL) { - return; // no TD attached - } + // process non-active (completed) QHD with attached (scheduled) TD + if ( !qtd_overlay->active && qhd->attached_qtd != NULL ) { + xfer_result_t xfer_result; - hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); + if ( qtd_overlay->halted ) { + if (qtd_overlay->xact_err || qtd_overlay->err_count == 0 || qtd_overlay->buffer_err || qtd_overlay->babble_err) { + // Error count = 0 often occurs when device disconnected, or other bus-related error + xfer_result = XFER_RESULT_FAILED; + TU_LOG3(" QHD xfer err count: %d\n", qtd_overlay->err_count); + // TU_BREAKPOINT(); // TODO skip unplugged device + }else { + // no error bits are set, endpoint is halted due to STALL + xfer_result = XFER_RESULT_STALLED; + } + } else { + xfer_result = XFER_RESULT_SUCCESS; + } - // TD is still active, no need to process - if (qtd->active) { - return; - } + ehci_qtd_t * volatile qtd = qhd->attached_qtd; + hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); // HC may have written back TD - uint8_t dir = (qtd->pid == EHCI_PID_IN) ? 1 : 0; - uint32_t const xferred_bytes = qtd->expected_bytes - qtd->total_bytes; + uint8_t const dir = (qtd->pid == EHCI_PID_IN) ? 1 : 0; + uint32_t const xferred_bytes = qtd->expected_bytes - qtd->total_bytes; - // invalidate dcache if IN transfer - if (dir == 1 && qhd->attached_buffer != 0 && xferred_bytes > 0) { - hcd_dcache_invalidate((void*) qhd->attached_buffer, xferred_bytes); - } + // invalidate dcache if IN transfer with data + if (dir == 1 && qhd->attached_buffer != 0 && xferred_bytes > 0) { + hcd_dcache_invalidate((void*) qhd->attached_buffer, xferred_bytes); + } - // remove and free TD before invoking callback - qhd_remove_qtd(qhd); + // remove and free TD before invoking callback + qhd_remove_qtd(qhd); - // notify usbh - uint8_t const ep_addr = tu_edpt_addr(qhd->ep_number, dir); - hcd_event_xfer_complete(qhd->dev_addr, ep_addr, xferred_bytes, XFER_RESULT_SUCCESS, true); + // notify usbh + uint8_t const ep_addr = tu_edpt_addr(qhd->ep_number, dir); + hcd_event_xfer_complete(qhd->dev_addr, ep_addr, xferred_bytes, xfer_result, true); + } } TU_ATTR_ALWAYS_INLINE static inline -void async_list_xfer_complete_isr(ehci_qhd_t * const async_head) +void proccess_async_xfer_isr(ehci_qhd_t * const list_head) { - ehci_qhd_t *p_qhd = async_head; - do - { - hcd_dcache_invalidate(p_qhd, sizeof(ehci_qhd_t)); - - // halted or error is processed in error isr - if ( !p_qhd->qtd_overlay.halted ) { - qhd_xfer_complete_isr(p_qhd); - } + ehci_qhd_t *qhd = list_head; - p_qhd = qhd_next(p_qhd); - }while(p_qhd != async_head); // async list traversal, stop if loop around + do { + qhd_xfer_complete_isr(qhd); + qhd = qhd_next(qhd); + } while ( qhd != list_head ); // async list traversal, stop if loop around } TU_ATTR_ALWAYS_INLINE static inline -void period_list_xfer_complete_isr(uint8_t rhport, uint32_t interval_ms) +void process_period_xfer_isr(uint8_t rhport, uint32_t interval_ms) { uint32_t const period_1ms_addr = (uint32_t) list_get_period_head(rhport, 1u); ehci_link_t next_link = *list_get_period_head(rhport, interval_ms); @@ -612,22 +616,13 @@ void period_list_xfer_complete_isr(uint8_t rhport, uint32_t interval_ms) switch (next_link.type) { case EHCI_QTYPE_QHD: { ehci_qhd_t *qhd = (ehci_qhd_t *) entry_addr; - hcd_dcache_invalidate(qhd, sizeof(ehci_qhd_t)); - - if (!qhd->qtd_overlay.halted) { - qhd_xfer_complete_isr(qhd); - } + qhd_xfer_complete_isr(qhd); } break; + // TODO support hs/fs ISO case EHCI_QTYPE_ITD: - // TODO support hs ISO - break; - case EHCI_QTYPE_SITD: - // TODO support split ISO - break; - case EHCI_QTYPE_FSTN: default: break; @@ -637,106 +632,6 @@ void period_list_xfer_complete_isr(uint8_t rhport, uint32_t interval_ms) } } -// TODO merge with qhd_xfer_complete_isr() -TU_ATTR_ALWAYS_INLINE static inline -void qhd_xfer_error_isr(ehci_qhd_t * qhd) -{ - volatile ehci_qtd_t *qtd_overlay = &qhd->qtd_overlay; - - // TD has error - if (qtd_overlay->halted) { - xfer_result_t xfer_result; - - if (qtd_overlay->xact_err || qtd_overlay->err_count == 0 || qtd_overlay->buffer_err || qtd_overlay->babble_err) { - // Error count = 0 often occurs when device disconnected, or other bus-related error - xfer_result = XFER_RESULT_FAILED; - }else { - // no error bits are set, endpoint is halted due to STALL - xfer_result = XFER_RESULT_STALLED; - } - -// if (XFER_RESULT_FAILED == xfer_result ) { -// TU_LOG1(" QHD xfer err count: %d\n", qtd_overlay->err_count); -// TU_BREAKPOINT(); // TODO skip unplugged device -// } - - ehci_qtd_t * volatile qtd = (ehci_qtd_t * volatile) qhd->attached_qtd; - TU_ASSERT(qtd, ); // No TD yet, probably a race condition or cache issue !? - - hcd_dcache_invalidate(qtd, sizeof(ehci_qtd_t)); - - uint8_t dir = (qtd->pid == EHCI_PID_IN) ? 1 : 0; - uint32_t const xferred_bytes = qtd->expected_bytes - qtd->total_bytes; - - // invalidate dcache if IN transfer - if (dir == 1 && qhd->attached_buffer != 0 && xferred_bytes > 0) { - hcd_dcache_invalidate((void*) qhd->attached_buffer, xferred_bytes); - } - - // remove and free TD before invoking callback - qhd_remove_qtd(qhd); - - if (0 == qhd->ep_number ) { - // control cannot be halted - qhd->qtd_overlay.next.terminate = 1; - qhd->qtd_overlay.alternate.terminate = 1; - qhd->qtd_overlay.halted = 0; - - hcd_dcache_clean(qhd, sizeof(ehci_qhd_t)); - } - - // notify usbh - uint8_t const ep_addr = tu_edpt_addr(qhd->ep_number, dir); - hcd_event_xfer_complete(qhd->dev_addr, ep_addr, xferred_bytes, xfer_result, true); - } -} - -TU_ATTR_ALWAYS_INLINE static inline -void xfer_error_isr(uint8_t rhport) -{ - //------------- async list -------------// - ehci_qhd_t * const async_head = list_get_async_head(rhport); - ehci_qhd_t *p_qhd = async_head; - do - { - hcd_dcache_invalidate(p_qhd, sizeof(ehci_qhd_t)); - qhd_xfer_error_isr( p_qhd ); - p_qhd = qhd_next(p_qhd); - }while(p_qhd != async_head); // async list traversal, stop if loop around - - //------------- TODO refractor period list -------------// - uint32_t const period_1ms_addr = (uint32_t) list_get_period_head(rhport, 1u); - for (uint32_t interval_ms=1; interval_ms <= FRAMELIST_SIZE; interval_ms *= 2) - { - ehci_link_t next_item = *list_get_period_head(rhport, interval_ms); - - // TODO abstract max loop guard for period - while( !next_item.terminate && - !(interval_ms > 1 && period_1ms_addr == tu_align32(next_item.address)) ) - { - switch ( next_item.type ) - { - case EHCI_QTYPE_QHD: - { - ehci_qhd_t *p_qhd_int = (ehci_qhd_t *) tu_align32(next_item.address); - hcd_dcache_invalidate(p_qhd_int, sizeof(ehci_qhd_t)); - - qhd_xfer_error_isr(p_qhd_int); - } - break; - - // TODO support hs/fs ISO - case EHCI_QTYPE_ITD: - case EHCI_QTYPE_SITD: - case EHCI_QTYPE_FSTN: - default: break; - } - - next_item = *list_next(&next_item); - } - } -} - //------------- Host Controller Driver's Interrupt Handler -------------// void hcd_int_handler(uint8_t rhport) { @@ -768,21 +663,16 @@ void hcd_int_handler(uint8_t rhport) regs->status = EHCI_INT_MASK_PORT_CHANGE; // Acknowledge } - // A USB transfer is completed with error - if (int_status & EHCI_INT_MASK_ERROR) { - xfer_error_isr(rhport); - regs->status = EHCI_INT_MASK_ERROR; // Acknowledge - } + // A USB transfer is completed (OK or error) + uint32_t const usb_int = int_status & (EHCI_INT_MASK_USB | EHCI_INT_MASK_ERROR); + if (usb_int) { + proccess_async_xfer_isr(list_get_async_head(rhport)); - // A USB transfer is completed - if (int_status & EHCI_INT_MASK_USB) { for ( uint32_t i = 1; i <= FRAMELIST_SIZE; i *= 2 ) { - period_list_xfer_complete_isr(rhport, i); + process_period_xfer_isr(rhport, i); } - async_list_xfer_complete_isr(list_get_async_head(rhport)); - - regs->status = EHCI_INT_MASK_USB; // Acknowledge + regs->status = usb_int; // Acknowledge } //------------- There is some removed async previously -------------// @@ -1011,8 +901,7 @@ TU_ATTR_ALWAYS_INLINE static inline ehci_qtd_t *qtd_find_free(void) { return NULL; } -static void qtd_init(ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes) -{ +static void qtd_init(ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes) { tu_memclr(qtd, sizeof(ehci_qtd_t)); qtd->used = 1; @@ -1026,8 +915,7 @@ static void qtd_init(ehci_qtd_t* qtd, void const* buffer, uint16_t total_bytes) qtd->expected_bytes = total_bytes; qtd->buffer[0] = (uint32_t) buffer; - for(uint8_t i=1; i<5; i++) - { + for(uint8_t i=1; i<5; i++) { qtd->buffer[i] |= tu_align4k(qtd->buffer[i - 1] ) + 4096; } } -- cgit v1.3.1 From fbaa148fe0f4a4b83f41efe9887a8909161710f6 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 18 Jul 2023 15:22:09 +0700 Subject: updating hcd rusb2 - make osal_task_delay() as weak function in usbh - implement osal_task_delay() in hcd rusb2 (may moved to other places) --- examples/device/cdc_msc_freertos/skip.txt | 1 + examples/device/hid_composite_freertos/skip.txt | 1 + examples/dual/host_hid_to_device_cdc/only.txt | 1 + hw/bsp/ra/boards/ra6m5_ek/board.cmake | 7 +- hw/bsp/ra/family.cmake | 2 +- src/host/usbh.c | 2 +- src/portable/renesas/rusb2/dcd_rusb2.c | 12 ++- src/portable/renesas/rusb2/hcd_rusb2.c | 123 +++++++++++------------- src/portable/renesas/rusb2/rusb2_ra.h | 7 -- 9 files changed, 78 insertions(+), 78 deletions(-) (limited to 'src/portable') diff --git a/examples/device/cdc_msc_freertos/skip.txt b/examples/device/cdc_msc_freertos/skip.txt index 49b8ee57b..a6f96b288 100644 --- a/examples/device/cdc_msc_freertos/skip.txt +++ b/examples/device/cdc_msc_freertos/skip.txt @@ -8,5 +8,6 @@ mcu:RP2040 mcu:SAMD11 mcu:SAMX7X mcu:VALENTYUSB_EPTRI +mcu:RAXXX family:broadcom_32bit family:broadcom_64bit diff --git a/examples/device/hid_composite_freertos/skip.txt b/examples/device/hid_composite_freertos/skip.txt index 49b8ee57b..a6f96b288 100644 --- a/examples/device/hid_composite_freertos/skip.txt +++ b/examples/device/hid_composite_freertos/skip.txt @@ -8,5 +8,6 @@ mcu:RP2040 mcu:SAMD11 mcu:SAMX7X mcu:VALENTYUSB_EPTRI +mcu:RAXXX family:broadcom_32bit family:broadcom_64bit diff --git a/examples/dual/host_hid_to_device_cdc/only.txt b/examples/dual/host_hid_to_device_cdc/only.txt index 6ee8e3fde..d9700677f 100644 --- a/examples/dual/host_hid_to_device_cdc/only.txt +++ b/examples/dual/host_hid_to_device_cdc/only.txt @@ -1,3 +1,4 @@ board:mimxrt1060_evk board:mimxrt1064_evk mcu:RP2040 +mcu:ra6m5 diff --git a/hw/bsp/ra/boards/ra6m5_ek/board.cmake b/hw/bsp/ra/boards/ra6m5_ek/board.cmake index 5a615f9b0..c91d48a32 100644 --- a/hw/bsp/ra/boards/ra6m5_ek/board.cmake +++ b/hw/bsp/ra/boards/ra6m5_ek/board.cmake @@ -3,15 +3,20 @@ set(MCU_VARIANT ra6m5) set(JLINK_DEVICE R7FA6M5BH) -# default to PORT1 Highspeed +# Device port default to PORT1 Highspeed if (NOT DEFINED PORT) set(PORT 1) endif() +# Host port will be the other port +set(HOST_PORT $) + function(update_board TARGET) target_compile_definitions(${TARGET} PUBLIC BOARD_TUD_RHPORT=${PORT} + BOARD_TUH_RHPORT=${HOST_PORT} # port 0 is fullspeed, port 1 is highspeed BOARD_TUD_MAX_SPEED=$ + BOARD_TUH_MAX_SPEED=$ ) endfunction() diff --git a/hw/bsp/ra/family.cmake b/hw/bsp/ra/family.cmake index f09e86a72..2c45b8d71 100644 --- a/hw/bsp/ra/family.cmake +++ b/hw/bsp/ra/family.cmake @@ -13,7 +13,7 @@ include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) set(CMAKE_TOOLCHAIN_FILE ${TOP}/tools/cmake/toolchain/arm_${TOOLCHAIN}.cmake) -set(FAMILY_MCUS RAXXX CACHE INTERNAL "") +set(FAMILY_MCUS RAXXX ${MCU_VARIANT} CACHE INTERNAL "") #------------------------------------ # BOARD_TARGET diff --git a/src/host/usbh.c b/src/host/usbh.c index 184bda23b..1418cfb79 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -256,7 +256,7 @@ static bool usbh_control_xfer_cb (uint8_t daddr, uint8_t ep_addr, xfer_result_t #if CFG_TUSB_OS == OPT_OS_NONE // TODO rework time-related function later -void osal_task_delay(uint32_t msec) +TU_ATTR_WEAK void osal_task_delay(uint32_t msec) { const uint32_t start = hcd_frame_number(_usbh_controller); while ( ( hcd_frame_number(_usbh_controller) - start ) < msec ) {} diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 358e5644b..6fee4edd7 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -27,12 +27,12 @@ #include "tusb_option.h" +#if CFG_TUD_ENABLED && defined(TUP_USBIP_RUSB2) + // Since TinyUSB doesn't use SOF for now, and this interrupt too often (1ms interval) // We disable SOF for now until needed later on #define USE_SOF 0 -#if CFG_TUD_ENABLED && defined(TUP_USBIP_RUSB2) - #include "device/dcd.h" #include "rusb2_type.h" @@ -53,6 +53,13 @@ #error "Unsupported MCU" #endif +//--------------------------------------------------------------------+ +// Application API for setting IRQ number +//--------------------------------------------------------------------+ +void tud_int_set_irqnum(uint8_t rhport, int32_t irqnum) { + rusb2_controller[rhport].irqnum = irqnum; +} + //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM //--------------------------------------------------------------------+ @@ -681,7 +688,6 @@ static void enable_interrupt(uint32_t pswi) void dcd_init(uint8_t rhport) { rusb2_reg_t* rusb = RUSB2_REG(rhport); - rusb2_module_start(rhport, true); #ifdef RUSB2_SUPPORT_HIGHSPEED diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 4e5ff0359..656051e2b 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -27,8 +27,7 @@ #include "tusb_option.h" -#if CFG_TUH_ENABLED && (TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) || \ - TU_CHECK_MCU(OPT_MCU_RAXXX)) +#if CFG_TUH_ENABLED && defined(TUP_USBIP_RUSB2) #include "host/hcd.h" #include "rusb2_type.h" @@ -41,8 +40,14 @@ #if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) #include "rusb2_rx.h" + #elif TU_CHECK_MCU(OPT_MCU_RAXXX) #include "rusb2_ra.h" + + void osal_task_delay(uint32_t msec) { + R_BSP_SoftwareDelay(msec, BSP_DELAY_UNITS_MILLISECONDS); + } + #else #error "Unsupported MCU" #endif @@ -67,19 +72,6 @@ TU_ATTR_PACKED_BEGIN TU_ATTR_BIT_FIELD_ORDER_BEGIN -typedef struct TU_ATTR_PACKED { - union { - struct { - uint16_t : 8; - uint16_t TRCLR: 1; - uint16_t TRENB: 1; - uint16_t : 0; - }; - uint16_t TRE; - }; - uint16_t TRN; -} reg_pipetre_t; - typedef union TU_ATTR_PACKED { struct { volatile uint16_t u8: 8; @@ -308,8 +300,9 @@ static bool pipe_xfer_out(unsigned num) pipe_write_packet(buf, (volatile void*)&RUSB2->D0FIFO, len); pipe->buf = (uint8_t*)buf + len; } - if (len < mps) + if (len < mps) { RUSB2->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + } RUSB2->D0FIFOSEL = 0; while (RUSB2->D0FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ pipe->remaining = rem - len; @@ -488,60 +481,60 @@ static void enable_interrupt(uint32_t pswi) bool hcd_init(uint8_t rhport) { - (void)rhport; - -#if (CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST) - RUSB2->SYSCFG_b.HSE = 1; - RUSB2->PHYSET_b.HSEB = 0; - RUSB2->PHYSET_b.DIRPD = 0; - R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MILLISECONDS); - RUSB2->PHYSET_b.PLLRESET = 0; - RUSB2->LPSTS_b.SUSPENDM = 1; - while (!RUSB2->PLLSTA_b.PLLLOCK); - RUSB2->SYSCFG_b.DRPD = 1; - RUSB2->SYSCFG_b.DCFM = 1; - RUSB2->SYSCFG_b.DPRPU = 0; - RUSB2->SYSCFG_b.CNEN = 1; - RUSB2->BUSWAIT |= 0x0F00U; - RUSB2->SOFCFG_b.INTL = 1; - RUSB2->DVSTCTR0_b.VBUSEN = 1; - RUSB2->CFIFOSEL_b.MBW = 1; - RUSB2->D0FIFOSEL_b.MBW = 1; - RUSB2->D1FIFOSEL_b.MBW = 1; - RUSB2->INTSTS0 = 0; - for (volatile int i = 0; i < 30000; ++i) ; - RUSB2->SYSCFG_b.USBE = 1; -#else - /* HOST DEVICE Full SPEED */ - RUSB2->SYSCFG_b.SCKE = 1; /* USB Clock enable */ - while (!RUSB2->SYSCFG_b.SCKE) ; - RUSB2->SYSCFG_b.DPRPU = 0; /* D+ pull up enable - 0/disable in host mode */ - RUSB2->SYSCFG_b.DRPD = 1; /* D+/D- pull down - 1/in Host mode (pag.834)*/ - RUSB2->SYSCFG_b.DCFM = 1; /* HOST or Device - 1/HOST */ - - RUSB2->DVSTCTR0_b.VBUSEN = 1; - - RUSB2->SYSCFG_b.DRPD = 1; - for (volatile int i = 0; i < 30000; ++i) ; - RUSB2->SYSCFG_b.USBE = 1; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + rusb2_module_start(rhport, true); + +#ifdef RUSB2_SUPPORT_HIGHSPEED + if (rusb2_is_highspeed_rhport(rhport) ) { + rusb->SYSCFG_b.HSE = 1; + rusb->PHYSET_b.HSEB = 0; + rusb->PHYSET_b.DIRPD = 0; + R_BSP_SoftwareDelay((uint32_t) 1, BSP_DELAY_UNITS_MILLISECONDS); + rusb->PHYSET_b.PLLRESET = 0; + rusb->LPSTS_b.SUSPENDM = 1; + while ( !rusb->PLLSTA_b.PLLLOCK ); + rusb->SYSCFG_b.DRPD = 1; + rusb->SYSCFG_b.DCFM = 1; + rusb->SYSCFG_b.DPRPU = 0; + rusb->SYSCFG_b.CNEN = 1; + rusb->BUSWAIT |= 0x0F00U; + rusb->SOFCFG_b.INTL = 1; + rusb->DVSTCTR0_b.VBUSEN = 1; + rusb->CFIFOSEL_b.MBW = 1; + rusb->D0FIFOSEL_b.MBW = 1; + rusb->D1FIFOSEL_b.MBW = 1; + rusb->INTSTS0 = 0; + for ( volatile int i = 0; i < 30000; ++i ); + rusb->SYSCFG_b.USBE = 1; + } else #endif + { + rusb->SYSCFG_b.SCKE = 1; + while ( !rusb->SYSCFG_b.SCKE ) {} + rusb->SYSCFG_b.DCFM = 1; // Host function + rusb->SYSCFG_b.DPRPU = 0; // Disable D+ pull up + rusb->SYSCFG_b.DRPD = 1; // Enable D+/D- pull down - // MCU specific PHY init - rusb2_phy_init(); + rusb->DVSTCTR0_b.VBUSEN = 1; + for ( volatile int i = 0; i < 30000; ++i ) {} // FIXME do we need to wait here? how long ? + //R_BSP_SoftwareDelay(10, BSP_DELAY_UNITS_MILLISECONDS); + rusb->SYSCFG_b.USBE = 1; -#if (CFG_TUSB_RHPORT0_MODE & OPT_MODE_HOST) - RUSB2->PHYSLEW = 0x5; - RUSB2->DPUSR0R_FS_b.FIXPHY0 = 0u; /* Transceiver Output fixed */ -#endif + // MCU specific PHY init + rusb2_phy_init(); + + rusb->PHYSLEW = 0x5; + rusb->DPUSR0R_FS_b.FIXPHY0 = 0u; /* Transceiver Output fixed */ + } /* Setup default control pipe */ - RUSB2->DCPCFG = RUSB2_PIPECFG_SHTNAK_Msk; - RUSB2->DCPMAXP = 64; - RUSB2->INTENB0 = RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_NRDY_Msk | RUSB2_INTSTS0_BEMP_Msk; - RUSB2->INTENB1 = RUSB2_INTSTS1_SACK_Msk | RUSB2_INTSTS1_SIGN_Msk | RUSB2_INTSTS1_ATTCH_Msk | RUSB2_INTSTS1_DTCH_Msk; - RUSB2->BEMPENB = 1; - RUSB2->NRDYENB = 1; - RUSB2->BRDYENB = 1; + rusb->DCPCFG = RUSB2_PIPECFG_SHTNAK_Msk; + rusb->DCPMAXP = 64; + rusb->INTENB0 = RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_NRDY_Msk | RUSB2_INTSTS0_BEMP_Msk; + rusb->INTENB1 = RUSB2_INTSTS1_SACK_Msk | RUSB2_INTSTS1_SIGN_Msk | RUSB2_INTSTS1_ATTCH_Msk | RUSB2_INTSTS1_DTCH_Msk; + rusb->BEMPENB = 1; + rusb->NRDYENB = 1; + rusb->BRDYENB = 1; return true; } diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 28b690512..8a4d2ad36 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -106,13 +106,6 @@ TU_ATTR_ALWAYS_INLINE static inline void rusb2_int_disable(uint8_t rhport) { TU_ATTR_ALWAYS_INLINE static inline void rusb2_phy_init(void) { } -//--------------------------------------------------------------------+ -// Application API for setting IRQ number -//--------------------------------------------------------------------+ -void tud_int_set_irqnum(uint8_t rhport, int32_t irqnum) { - rusb2_controller[rhport].irqnum = irqnum; -} - #ifdef __cplusplus } #endif -- cgit v1.3.1 From 6b6dcc6c099eeafaa6d76bf6133181874beabc0d Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 26 Jul 2023 19:50:50 +0700 Subject: refactored multiple ports for hcd rusb2 --- .idea/cmake.xml | 15 +- .idea/runConfigurations/ra6m5.xml | 2 +- hw/bsp/ra/boards/ra6m5_ek/ozone/ra6m5.jdebug | 4 +- src/portable/renesas/rusb2/dcd_rusb2.c | 37 +-- src/portable/renesas/rusb2/hcd_rusb2.c | 452 ++++++++++++++------------- 5 files changed, 268 insertions(+), 242 deletions(-) (limited to 'src/portable') diff --git a/.idea/cmake.xml b/.idea/cmake.xml index 864ff615b..519623b71 100644 --- a/.idea/cmake.xml +++ b/.idea/cmake.xml @@ -2,7 +2,6 @@ - @@ -26,27 +25,27 @@ - - - + + + - + + - - - + + \ No newline at end of file diff --git a/.idea/runConfigurations/ra6m5.xml b/.idea/runConfigurations/ra6m5.xml index 02df11610..89f9787a0 100644 --- a/.idea/runConfigurations/ra6m5.xml +++ b/.idea/runConfigurations/ra6m5.xml @@ -1,5 +1,5 @@ - + diff --git a/hw/bsp/ra/boards/ra6m5_ek/ozone/ra6m5.jdebug b/hw/bsp/ra/boards/ra6m5_ek/ozone/ra6m5.jdebug index aebb29162..7b8ee9c95 100644 --- a/hw/bsp/ra/boards/ra6m5_ek/ozone/ra6m5.jdebug +++ b/hw/bsp/ra/boards/ra6m5_ek/ozone/ra6m5.jdebug @@ -20,7 +20,9 @@ void OnProjectLoad (void) { Project.SetTraceSource ("Trace Pins"); Project.SetTracePortWidth (4); - File.Open ("../../../../../../examples/device/cdc_msc/cmake-build-ra6m5/cdc_msc.elf"); + //File.Open ("../../../../../../examples/device/cdc_msc/cmake-build-ra6m5/cdc_msc.elf"); + //File.Open ("../../../../../../examples/dual/cmake-build-ra6m5/host_hid_to_device_cdc/host_hid_to_device_cdc.elf"); + File.Open ("../../../../../../examples/cmake-build-ra6m5/host/cdc_msc_hid/cdc_msc_hid.elf"); } /********************************************************************* * diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 6fee4edd7..83f0fdc4a 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -83,6 +83,18 @@ typedef struct TU_ATTR_PACKED TU_ATTR_PACKED_END // End of definition of packed structs (used by the CCRX toolchain) TU_ATTR_BIT_FIELD_ORDER_END +typedef struct +{ + pipe_state_t pipe[10]; + uint8_t ep[2][16]; /* a lookup table for a pipe index from an endpoint address */ +} dcd_data_t; + +static dcd_data_t _dcd; + +//--------------------------------------------------------------------+ +// INTERNAL OBJECT & FUNCTION DECLARATION +//--------------------------------------------------------------------+ + // Transfer conditions specifiable for each pipe: // - Pipe 0: Control transfer with 64-byte single buffer // - Pipes 1 and 2: Bulk isochronous transfer continuous transfer mode with programmable buffer size up @@ -96,18 +108,6 @@ enum { PIPE_COUNT = 10, }; -typedef struct -{ - pipe_state_t pipe[10]; - uint8_t ep[2][16]; /* a lookup table for a pipe index from an endpoint address */ -} dcd_data_t; - -static dcd_data_t _dcd; - -//--------------------------------------------------------------------+ -// INTERNAL OBJECT & FUNCTION DECLARATION -//--------------------------------------------------------------------+ - static unsigned find_pipe(unsigned xfer) { switch (xfer) { @@ -746,20 +746,17 @@ void dcd_init(uint8_t rhport) } } -void dcd_int_enable(uint8_t rhport) -{ +void dcd_int_enable(uint8_t rhport) { rusb2_int_enable(rhport); } -void dcd_int_disable(uint8_t rhport) -{ +void dcd_int_disable(uint8_t rhport) { rusb2_int_disable(rhport); } -void dcd_set_address(uint8_t rhport, uint8_t dev_addr) -{ - (void)rhport; - (void)dev_addr; +void dcd_set_address(uint8_t rhport, uint8_t dev_addr) { + (void) rhport; + (void) dev_addr; } void dcd_remote_wakeup(uint8_t rhport) diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 656051e2b..a4b534a05 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -52,23 +52,12 @@ #error "Unsupported MCU" #endif -#define TU_RUSB2_HCD_DBG 0 +#define TU_RUSB2_HCD_DBG 2 //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM DECLARATION //--------------------------------------------------------------------+ -/* LINK core registers */ -#if defined(__CCRX__) - #define RUSB2 ((RUSB2_REG_t __evenaccess*) RUSB2_REG_BASE) -#elif defined(__RX__) - #define RUSB2 ((RUSB2_REG_t*) RUSB2_REG_BASE) -#elif (CFG_TUSB_RHPORT1_MODE & OPT_MODE_HOST) - #define RUSB2 ((R_USB_HS0_Type*) R_USB_HS0_BASE) -#else - #define RUSB2 ((R_USB_FS0_Type*) R_USB_FS0_BASE) -#endif - TU_ATTR_PACKED_BEGIN TU_ATTR_BIT_FIELD_ORDER_BEGIN @@ -108,79 +97,97 @@ typedef struct //--------------------------------------------------------------------+ static hcd_data_t _hcd; -static unsigned find_pipe(unsigned xfer) -{ - switch (xfer) { - case TUSB_XFER_ISOCHRONOUS: - for (int i = 1; i <= 2; ++i) { - if (0 == _hcd.pipe[i].ep) return i; - } - break; - case TUSB_XFER_BULK: - for (int i = 3; i <= 5; ++i) { - if (0 == _hcd.pipe[i].ep) return i; - } - for (int i = 1; i <= 2; ++i) { - if (0 == _hcd.pipe[i].ep) return i; - } - break; - case TUSB_XFER_INTERRUPT: - for (int i = 6; i <= 9; ++i) { - if (0 == _hcd.pipe[i].ep) return i; - } - break; - default: - /* No support for control transfer */ - break; +// TODO merged with DCD +// Transfer conditions specifiable for each pipe: +// - Pipe 0: Control transfer with 64-byte single buffer +// - Pipes 1 and 2: Bulk isochronous transfer continuous transfer mode with programmable buffer size up +// to 2 KB and optional double buffer +// - Pipes 3 to 5: Bulk transfer continuous transfer mode with programmable buffer size up to 2 KB and +// optional double buffer +// - Pipes 6 to 9: Interrupt transfer with 64-byte single buffer +enum { + PIPE_1ST_BULK = 3, + PIPE_1ST_INTERRUPT = 6, + PIPE_COUNT = 10, +}; + +static unsigned find_pipe(unsigned xfer) { + switch ( xfer ) { + case TUSB_XFER_ISOCHRONOUS: + for (int i = 1; i < PIPE_1ST_BULK; ++i) { + if ( 0 == _hcd.pipe[i].ep ) return i; + } + break; + + case TUSB_XFER_BULK: + for (int i = PIPE_1ST_BULK; i < PIPE_1ST_INTERRUPT; ++i) { + if ( 0 == _hcd.pipe[i].ep ) return i; + } + for (int i = 1; i < PIPE_1ST_BULK; ++i) { + if ( 0 == _hcd.pipe[i].ep ) return i; + } + break; + + case TUSB_XFER_INTERRUPT: + for (int i = PIPE_1ST_INTERRUPT; i < PIPE_COUNT; ++i) { + if ( 0 == _hcd.pipe[i].ep ) return i; + } + break; + + default: + /* No support for control transfer */ + break; } return 0; } -static volatile uint16_t* get_pipectr(unsigned num) +static volatile uint16_t* get_pipectr(rusb2_reg_t *rusb, unsigned num) { if (num) { - return (volatile uint16_t*)&(RUSB2->PIPE_CTR[num - 1]); + return (volatile uint16_t*)&(rusb->PIPE_CTR[num - 1]); } else { - return (volatile uint16_t*)&(RUSB2->DCPCTR); + return (volatile uint16_t*)&(rusb->DCPCTR); } } -static volatile reg_pipetre_t* get_pipetre(unsigned num) +static volatile reg_pipetre_t* get_pipetre(rusb2_reg_t *rusb, unsigned num) { volatile reg_pipetre_t* tre = NULL; if ((1 <= num) && (num <= 5)) { - tre = (volatile reg_pipetre_t*)&(RUSB2->PIPE_TR[num - 1].E); + tre = (volatile reg_pipetre_t*)&(rusb->PIPE_TR[num - 1].E); } return tre; } -static volatile uint16_t* addr_to_pipectr(uint8_t dev_addr, unsigned ep_addr) +static volatile uint16_t* addr_to_pipectr(uint8_t rhport, uint8_t dev_addr, unsigned ep_addr) { + rusb2_reg_t* rusb = RUSB2_REG(rhport); const unsigned epn = tu_edpt_number(ep_addr); + if (epn) { const unsigned dir_in = tu_edpt_dir(ep_addr); const unsigned num = _hcd.ep[dev_addr][dir_in][epn - 1]; - return get_pipectr(num); + return get_pipectr(rusb, num); } else { - return get_pipectr(0); + return get_pipectr(rusb, 0); } } -static unsigned edpt0_max_packet_size(void) +static uint16_t edpt0_max_packet_size(rusb2_reg_t* rusb) { - return RUSB2->DCPMAXP_b.MXPS; + return rusb->DCPMAXP_b.MXPS; } -static unsigned edpt_max_packet_size(unsigned num) +static uint16_t edpt_max_packet_size(rusb2_reg_t *rusb, unsigned num) { - RUSB2->PIPESEL = num; - return RUSB2->PIPEMAXP_b.MXPS; + rusb->PIPESEL = num; + return rusb->PIPEMAXP_b.MXPS; } -static inline void pipe_wait_for_ready(unsigned num) +static inline void pipe_wait_for_ready(rusb2_reg_t* rusb, unsigned num) { - while (RUSB2->D0FIFOSEL_b.CURPIPE != num) ; - while (!RUSB2->D0FIFOCTR_b.FRDY) ; + while (rusb->D0FIFOSEL_b.CURPIPE != num) ; + while (!rusb->D0FIFOCTR_b.FRDY) {} } static void pipe_write_packet(void *buf, volatile void *fifo, unsigned len) @@ -205,33 +212,33 @@ static void pipe_read_packet(void *buf, volatile void *fifo, unsigned len) while (len--) *p++ = *reg; } -static bool pipe0_xfer_in(void) +static bool pipe0_xfer_in(rusb2_reg_t* rusb) { pipe_state_t *pipe = &_hcd.pipe[0]; const unsigned rem = pipe->remaining; - const unsigned mps = edpt0_max_packet_size(); - const unsigned vld = RUSB2->CFIFOCTR_b.DTLN; + const unsigned mps = edpt0_max_packet_size(rusb); + const unsigned vld = rusb->CFIFOCTR_b.DTLN; const unsigned len = TU_MIN(TU_MIN(rem, mps), vld); void *buf = pipe->buf; if (len) { - RUSB2->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; - pipe_read_packet(buf, (volatile void*)&RUSB2->CFIFO, len); + rusb->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; + pipe_read_packet(buf, (volatile void*)&rusb->CFIFO, len); pipe->buf = (uint8_t*)buf + len; } if (len < mps) { - RUSB2->CFIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; + rusb->CFIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; } pipe->remaining = rem - len; if ((len < mps) || (rem == len)) { pipe->buf = NULL; return true; } - RUSB2->DCPCTR = RUSB2_PIPE_CTR_PID_BUF; + rusb->DCPCTR = RUSB2_PIPE_CTR_PID_BUF; return false; } -static bool pipe0_xfer_out(void) +static bool pipe0_xfer_out(rusb2_reg_t* rusb) { pipe_state_t *pipe = &_hcd.pipe[0]; const unsigned rem = pipe->remaining; @@ -239,40 +246,40 @@ static bool pipe0_xfer_out(void) pipe->buf = NULL; return true; } - const unsigned mps = edpt0_max_packet_size(); + const unsigned mps = edpt0_max_packet_size(rusb); const unsigned len = TU_MIN(mps, rem); void *buf = pipe->buf; if (len) { - pipe_write_packet(buf, (volatile void*)&RUSB2->CFIFO, len); + pipe_write_packet(buf, (volatile void*)&rusb->CFIFO, len); pipe->buf = (uint8_t*)buf + len; } if (len < mps) { - RUSB2->CFIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + rusb->CFIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; } pipe->remaining = rem - len; return false; } -static bool pipe_xfer_in(unsigned num) +static bool pipe_xfer_in(rusb2_reg_t* rusb, unsigned num) { pipe_state_t *pipe = &_hcd.pipe[num]; const unsigned rem = pipe->remaining; - RUSB2->D0FIFOSEL = num | RUSB2_FIFOSEL_MBW_8BIT; - const unsigned mps = edpt_max_packet_size(num); - pipe_wait_for_ready(num); - const unsigned vld = RUSB2->D0FIFOCTR_b.DTLN; + rusb->D0FIFOSEL = num | RUSB2_FIFOSEL_MBW_8BIT; + const unsigned mps = edpt_max_packet_size(rusb, num); + pipe_wait_for_ready(rusb, num); + const unsigned vld = rusb->D0FIFOCTR_b.DTLN; const unsigned len = TU_MIN(TU_MIN(rem, mps), vld); void *buf = pipe->buf; if (len) { - pipe_read_packet(buf, (volatile void*)&RUSB2->D0FIFO, len); + pipe_read_packet(buf, (volatile void*)&rusb->D0FIFO, len); pipe->buf = (uint8_t*)buf + len; } if (len < mps) { - RUSB2->D0FIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; + rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; } - RUSB2->D0FIFOSEL = 0; - while (RUSB2->D0FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ + rusb->D0FIFOSEL = 0; + while (rusb->D0FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ pipe->remaining = rem - len; if ((len < mps) || (rem == len)) { pipe->buf = NULL; @@ -281,7 +288,7 @@ static bool pipe_xfer_in(unsigned num) return false; } -static bool pipe_xfer_out(unsigned num) +static bool pipe_xfer_out(rusb2_reg_t* rusb, unsigned num) { pipe_state_t *pipe = &_hcd.pipe[num]; const unsigned rem = pipe->remaining; @@ -291,37 +298,39 @@ static bool pipe_xfer_out(unsigned num) return true; } - RUSB2->D0FIFOSEL = num | RUSB2_FIFOSEL_MBW_16BIT | (TU_BYTE_ORDER == TU_BIG_ENDIAN ? RUSB2_FIFOSEL_BIGEND : 0); - const unsigned mps = edpt_max_packet_size(num); - pipe_wait_for_ready(num); + rusb->D0FIFOSEL = num | RUSB2_FIFOSEL_MBW_16BIT | (TU_BYTE_ORDER == TU_BIG_ENDIAN ? RUSB2_FIFOSEL_BIGEND : 0); + const unsigned mps = edpt_max_packet_size(rusb, num); + pipe_wait_for_ready(rusb, num); const unsigned len = TU_MIN(rem, mps); void *buf = pipe->buf; if (len) { - pipe_write_packet(buf, (volatile void*)&RUSB2->D0FIFO, len); + pipe_write_packet(buf, (volatile void*)&rusb->D0FIFO, len); pipe->buf = (uint8_t*)buf + len; } if (len < mps) { - RUSB2->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; } - RUSB2->D0FIFOSEL = 0; - while (RUSB2->D0FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ + rusb->D0FIFOSEL = 0; + while (rusb->D0FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ pipe->remaining = rem - len; return false; } -static bool process_pipe0_xfer(uint8_t dev_addr, uint8_t ep_addr, void* buffer, uint16_t buflen) +static bool process_pipe0_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, void* buffer, uint16_t buflen) { (void)dev_addr; + + rusb2_reg_t* rusb = RUSB2_REG(rhport); const unsigned dir_in = tu_edpt_dir(ep_addr); /* configure fifo direction and access unit settings */ if (dir_in) { /* IN, a byte */ - RUSB2->CFIFOSEL = RUSB2_FIFOSEL_MBW_8BIT; - while (RUSB2->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE) ; + rusb->CFIFOSEL = RUSB2_FIFOSEL_MBW_8BIT; + while (rusb->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE) ; } else { /* OUT, 2 bytes */ - RUSB2->CFIFOSEL = RUSB2_CFIFOSEL_ISEL_WRITE | RUSB2_FIFOSEL_MBW_16BIT | + rusb->CFIFOSEL = RUSB2_CFIFOSEL_ISEL_WRITE | RUSB2_FIFOSEL_MBW_16BIT | (TU_BYTE_ORDER == TU_BIG_ENDIAN ? RUSB2_FIFOSEL_BIGEND : 0); - while (!(RUSB2->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE)) ; + while (!(rusb->CFIFOSEL & RUSB2_CFIFOSEL_ISEL_WRITE)) ; } pipe_state_t *pipe = &_hcd.pipe[0]; @@ -331,26 +340,28 @@ static bool process_pipe0_xfer(uint8_t dev_addr, uint8_t ep_addr, void* buffer, if (buflen) { pipe->buf = buffer; if (!dir_in) { /* OUT */ - TU_ASSERT(RUSB2->DCPCTR_b.BSTS && (RUSB2->USBREQ & 0x80)); - pipe0_xfer_out(); + TU_ASSERT(rusb->DCPCTR_b.BSTS && (rusb->USBREQ & 0x80)); + pipe0_xfer_out(rusb); } } else { /* ZLP */ pipe->buf = NULL; if (!dir_in) { /* OUT */ - RUSB2->CFIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + rusb->CFIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; } - if (dir_in == RUSB2->DCPCFG_b.DIR) { - TU_ASSERT(RUSB2_PIPE_CTR_PID_NAK == RUSB2->DCPCTR_b.PID); - RUSB2->DCPCTR_b.SQSET = 1; - RUSB2->DCPCFG_b.DIR = dir_in ^ 1; + if (dir_in == rusb->DCPCFG_b.DIR) { + TU_ASSERT(RUSB2_PIPE_CTR_PID_NAK == rusb->DCPCTR_b.PID); + rusb->DCPCTR_b.SQSET = 1; + rusb->DCPCFG_b.DIR = dir_in ^ 1; } } - RUSB2->DCPCTR = RUSB2_PIPE_CTR_PID_BUF; + rusb->DCPCTR = RUSB2_PIPE_CTR_PID_BUF; return true; } -static bool process_pipe_xfer(uint8_t dev_addr, uint8_t ep_addr, void *buffer, uint16_t buflen) +static bool process_pipe_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, void *buffer, uint16_t buflen) { + rusb2_reg_t* rusb = RUSB2_REG(rhport); + const unsigned epn = tu_edpt_number(ep_addr); const unsigned dir_in = tu_edpt_dir(ep_addr); const unsigned num = _hcd.ep[dev_addr - 1][dir_in][epn - 1]; @@ -363,19 +374,19 @@ static bool process_pipe_xfer(uint8_t dev_addr, uint8_t ep_addr, void *buffer, u pipe->remaining = buflen; if (!dir_in) { /* OUT */ if (buflen) { - pipe_xfer_out(num); + pipe_xfer_out(rusb, num); } else { /* ZLP */ - RUSB2->D0FIFOSEL = num; - pipe_wait_for_ready(num); - RUSB2->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; - RUSB2->D0FIFOSEL = 0; - while (RUSB2->D0FIFOSEL_b.CURPIPE) {} /* if CURPIPE bits changes, check written value */ + rusb->D0FIFOSEL = num; + pipe_wait_for_ready(rusb, num); + rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + rusb->D0FIFOSEL = 0; + while (rusb->D0FIFOSEL_b.CURPIPE) {} /* if CURPIPE bits changes, check written value */ } } else { - volatile uint16_t *ctr = get_pipectr(num); - volatile reg_pipetre_t *pt = get_pipetre(num); + volatile uint16_t *ctr = get_pipectr(rusb, num); + volatile reg_pipetre_t *pt = get_pipetre(rusb, num); if (pt) { - const unsigned mps = edpt_max_packet_size(num); + const unsigned mps = edpt_max_packet_size(rusb, num); if (*ctr & 0x3) *ctr = RUSB2_PIPE_CTR_PID_NAK; pt->TRE = TU_BIT(8); pt->TRN = (buflen + mps - 1) / mps; @@ -386,20 +397,20 @@ static bool process_pipe_xfer(uint8_t dev_addr, uint8_t ep_addr, void *buffer, u return true; } -static bool process_edpt_xfer(uint8_t dev_addr, uint8_t ep_addr, void* buffer, uint16_t buflen) +static bool process_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, void* buffer, uint16_t buflen) { const unsigned epn = tu_edpt_number(ep_addr); if (0 == epn) { - return process_pipe0_xfer(dev_addr, ep_addr, buffer, buflen); + return process_pipe0_xfer(rhport, dev_addr, ep_addr, buffer, buflen); } else { - return process_pipe_xfer(dev_addr, ep_addr, buffer, buflen); + return process_pipe_xfer(rhport, dev_addr, ep_addr, buffer, buflen); } } static void process_pipe0_bemp(uint8_t rhport) { - (void)rhport; - bool completed = pipe0_xfer_out(); + rusb2_reg_t* rusb = RUSB2_REG(rhport); + bool completed = pipe0_xfer_out(rusb); if (completed) { pipe_state_t *pipe = &_hcd.pipe[0]; hcd_event_xfer_complete(pipe->dev, @@ -411,9 +422,9 @@ static void process_pipe0_bemp(uint8_t rhport) static void process_pipe_nrdy(uint8_t rhport, unsigned num) { - (void)rhport; + rusb2_reg_t* rusb = RUSB2_REG(rhport); xfer_result_t result; - uint16_t volatile *ctr = get_pipectr(num); + uint16_t volatile *ctr = get_pipectr(rusb, num); TU_LOG(TU_RUSB2_HCD_DBG, "NRDY %d %x\n", num, *ctr); switch (*ctr & RUSB2_PIPE_CTR_PID_Msk) { default: return; @@ -429,19 +440,19 @@ static void process_pipe_nrdy(uint8_t rhport, unsigned num) static void process_pipe_brdy(uint8_t rhport, unsigned num) { - (void)rhport; + rusb2_reg_t* rusb = RUSB2_REG(rhport); pipe_state_t *pipe = &_hcd.pipe[num]; const unsigned dir_in = tu_edpt_dir(pipe->ep); bool completed; if (dir_in) { /* IN */ if (num) { - completed = pipe_xfer_in(num); + completed = pipe_xfer_in(rusb, num); } else { - completed = pipe0_xfer_in(); + completed = pipe0_xfer_in(rusb); } } else { - completed = pipe_xfer_out(num); + completed = pipe_xfer_out(rusb, num); } if (completed) { hcd_event_xfer_complete(pipe->dev, pipe->ep, @@ -539,86 +550,88 @@ bool hcd_init(uint8_t rhport) return true; } -void hcd_int_enable(uint8_t rhport) -{ +void hcd_int_enable(uint8_t rhport) { rusb2_int_enable(rhport); } -void hcd_int_disable(uint8_t rhport) -{ +void hcd_int_disable(uint8_t rhport) { rusb2_int_disable(rhport); } uint32_t hcd_frame_number(uint8_t rhport) { - (void)rhport; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + /* The device must be reset at least once after connection * in order to start the frame counter. */ if (_hcd.need_reset) hcd_port_reset(rhport); - return RUSB2->FRMNUM_b.FRNM; + return rusb->FRMNUM_b.FRNM; } /*--------------------------------------------------------------------+ * Port API *--------------------------------------------------------------------+*/ -bool hcd_port_connect_status(uint8_t rhport) -{ - (void)rhport; - return RUSB2->INTSTS1_b.ATTCH ? true : false; +bool hcd_port_connect_status(uint8_t rhport) { + rusb2_reg_t* rusb = RUSB2_REG(rhport); + return rusb->INTSTS1_b.ATTCH ? true : false; } -void hcd_port_reset(uint8_t rhport) -{ - RUSB2->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; - while (RUSB2->DCPCTR_b.PBUSY) ; +void hcd_port_reset(uint8_t rhport) { + rusb2_reg_t* rusb = RUSB2_REG(rhport); + rusb->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; + while (rusb->DCPCTR_b.PBUSY) {} + hcd_int_disable(rhport); - RUSB2->DVSTCTR0_b.UACT = 0; - if (RUSB2->DCPCTR_b.SUREQ) { - RUSB2->DCPCTR_b.SUREQCLR = 1; + rusb->DVSTCTR0_b.UACT = 0; + if (rusb->DCPCTR_b.SUREQ) { + rusb->DCPCTR_b.SUREQCLR = 1; } hcd_int_enable(rhport); + /* Reset should be asserted 10-20ms. */ - RUSB2->DVSTCTR0_b.USBRST = 1; - for (volatile int i = 0; i < 2400000; ++i) ; - RUSB2->DVSTCTR0_b.USBRST = 0; - RUSB2->DVSTCTR0_b.UACT = 1; + rusb->DVSTCTR0_b.USBRST = 1; + for (volatile int i = 0; i < 2400000; ++i) {} + rusb->DVSTCTR0_b.USBRST = 0; + + rusb->DVSTCTR0_b.UACT = 1; _hcd.need_reset = false; } -void hcd_port_reset_end(uint8_t rhport) -{ +void hcd_port_reset_end(uint8_t rhport) { (void) rhport; } -tusb_speed_t hcd_port_speed_get(uint8_t rhport) -{ - (void)rhport; - switch (RUSB2->DVSTCTR0_b.RHST) { - default: return TUSB_SPEED_INVALID; +tusb_speed_t hcd_port_speed_get(uint8_t rhport) { + rusb2_reg_t* rusb = RUSB2_REG(rhport); + switch (rusb->DVSTCTR0_b.RHST) { + case RUSB2_DVSTCTR0_RHST_HS: return TUSB_SPEED_HIGH; case RUSB2_DVSTCTR0_RHST_FS: return TUSB_SPEED_FULL; - case RUSB2_DVSTCTR0_RHST_LS: return TUSB_SPEED_LOW; + case RUSB2_DVSTCTR0_RHST_LS: return TUSB_SPEED_LOW; + default: return TUSB_SPEED_INVALID; } } -void hcd_device_close(uint8_t rhport, uint8_t dev_addr) -{ - (void)rhport; +void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { + rusb2_reg_t* rusb = RUSB2_REG(rhport); uint16_t volatile *ctr; + TU_ASSERT(dev_addr < 6,); /* USBa can only handle addresses from 0 to 5. */ if (!dev_addr) return; + _hcd.ctl_mps[dev_addr] = 0; uint8_t *ep = &_hcd.ep[dev_addr - 1][0][0]; + for (int i = 0; i < 2 * 15; ++i, ++ep) { unsigned num = *ep; if (!num || (dev_addr != _hcd.pipe[num].dev)) continue; - ctr = (uint16_t volatile*)&RUSB2->PIPE_CTR[num - 1]; + ctr = (uint16_t volatile*)&rusb->PIPE_CTR[num - 1]; *ctr = 0; - RUSB2->NRDYENB &= ~TU_BIT(num); - RUSB2->BRDYENB &= ~TU_BIT(num); - RUSB2->PIPESEL = num; - RUSB2->PIPECFG = 0; - RUSB2->PIPEMAXP = 0; + rusb->NRDYENB &= ~TU_BIT(num); + rusb->BRDYENB &= ~TU_BIT(num); + rusb->PIPESEL = num; + rusb->PIPECFG = 0; + rusb->PIPEMAXP = 0; _hcd.pipe[num].ep = 0; _hcd.pipe[num].dev = 0; @@ -631,52 +644,54 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) *--------------------------------------------------------------------+*/ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { - (void)rhport; - TU_LOG(TU_RUSB2_HCD_DBG, "S %d %x\n", dev_addr, RUSB2->DCPCTR); - TU_ASSERT(dev_addr < 6); /* USBa can only handle addresses from 0 to 5. */ - TU_ASSERT(0 == RUSB2->DCPCTR_b.SUREQ); - RUSB2->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; + rusb2_reg_t* rusb = RUSB2_REG(rhport); + TU_LOG(TU_RUSB2_HCD_DBG, "S %d %x\n", dev_addr, rusb->DCPCTR); + + TU_ASSERT(0 == rusb->DCPCTR_b.SUREQ); + + rusb->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; _hcd.pipe[0].buf = NULL; _hcd.pipe[0].length = 8; _hcd.pipe[0].remaining = 0; _hcd.pipe[0].dev = dev_addr; - while (RUSB2->DCPCTR_b.PBUSY) ; - RUSB2->DCPMAXP = (dev_addr << 12) | _hcd.ctl_mps[dev_addr]; + while (rusb->DCPCTR_b.PBUSY) ; + rusb->DCPMAXP = (dev_addr << 12) | _hcd.ctl_mps[dev_addr]; /* Set direction in advance for DATA stage */ uint8_t const bmRequesttype = setup_packet[0]; - RUSB2->DCPCFG_b.DIR = tu_edpt_dir(bmRequesttype) ? 0: 1; + rusb->DCPCFG_b.DIR = tu_edpt_dir(bmRequesttype) ? 0: 1; uint16_t const* p = (uint16_t const*)(uintptr_t)&setup_packet[0]; - RUSB2->USBREQ = tu_htole16(p[0]); - RUSB2->USBVAL = p[1]; - RUSB2->USBINDX = p[2]; - RUSB2->USBLENG = p[3]; + rusb->USBREQ = tu_htole16(p[0]); + rusb->USBVAL = p[1]; + rusb->USBINDX = p[2]; + rusb->USBLENG = p[3]; - RUSB2->DCPCTR_b.SUREQ = 1; + rusb->DCPCTR_b.SUREQ = 1; return true; } bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const *ep_desc) { - (void)rhport; TU_ASSERT(dev_addr < 6); /* USBa can only handle addresses from 0 to 5. */ + rusb2_reg_t* rusb = RUSB2_REG(rhport); const unsigned ep_addr = ep_desc->bEndpointAddress; const unsigned epn = tu_edpt_number(ep_addr); const unsigned mps = tu_edpt_packet_size(ep_desc); + if (0 == epn) { - RUSB2->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; + rusb->DCPCTR = RUSB2_PIPE_CTR_PID_NAK; hcd_devtree_info_t devtree; hcd_devtree_get_info(dev_addr, &devtree); - uint16_t volatile *devadd = (uint16_t volatile *)(uintptr_t) &RUSB2->DEVADD[0]; + uint16_t volatile *devadd = (uint16_t volatile *)(uintptr_t) &rusb->DEVADD[0]; devadd += dev_addr; - while (RUSB2->DCPCTR_b.PBUSY) ; - RUSB2->DCPMAXP = (dev_addr << 12) | mps; + while (rusb->DCPCTR_b.PBUSY) {} + rusb->DCPMAXP = (dev_addr << 12) | mps; *devadd = (TUSB_SPEED_FULL == devtree.speed) ? RUSB2_DEVADD_USBSPD_FS : RUSB2_DEVADD_USBSPD_LS; _hcd.ctl_mps[dev_addr] = mps; return true; @@ -690,17 +705,20 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const } const unsigned num = find_pipe(xfer); if (!num) return false; + _hcd.pipe[num].dev = dev_addr; _hcd.pipe[num].ep = ep_addr; _hcd.ep[dev_addr - 1][dir_in][epn - 1] = num; /* setup pipe */ hcd_int_disable(rhport); - RUSB2->PIPESEL = num; - RUSB2->PIPEMAXP = (dev_addr << 12) | mps; - volatile uint16_t *ctr = get_pipectr(num); + + rusb->PIPESEL = num; + rusb->PIPEMAXP = (dev_addr << 12) | mps; + volatile uint16_t *ctr = get_pipectr(rusb, num); *ctr = RUSB2_PIPE_CTR_ACLRM_Msk | RUSB2_PIPE_CTR_SQCLR_Msk; *ctr = 0; + unsigned cfg = ((1 ^ dir_in) << 4) | epn; if (xfer == TUSB_XFER_BULK) { cfg |= RUSB2_PIPECFG_TYPE_BULK | RUSB2_PIPECFG_SHTNAK_Msk | RUSB2_PIPECFG_DBLB_Msk; @@ -709,13 +727,16 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const } else { cfg |= RUSB2_PIPECFG_TYPE_ISO | RUSB2_PIPECFG_DBLB_Msk; } - RUSB2->PIPECFG = cfg; - RUSB2->BRDYSTS = 0x1FFu ^ TU_BIT(num); - RUSB2->NRDYENB |= TU_BIT(num); - RUSB2->BRDYENB |= TU_BIT(num); + + rusb->PIPECFG = cfg; + rusb->BRDYSTS = 0x1FFu ^ TU_BIT(num); + rusb->NRDYENB |= TU_BIT(num); + rusb->BRDYENB |= TU_BIT(num); + if (!dir_in) { *ctr = RUSB2_PIPE_CTR_PID_BUF; } + hcd_int_enable(rhport); return true; @@ -726,14 +747,15 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t *b bool r; hcd_int_disable(rhport); TU_LOG(TU_RUSB2_HCD_DBG, "X %d %x %u\n", dev_addr, ep_addr, buflen); - r = process_edpt_xfer(dev_addr, ep_addr, buffer, buflen); + r = process_edpt_xfer(rhport, dev_addr, ep_addr, buffer, buflen); hcd_int_enable(rhport); return r; } bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) { - uint16_t volatile *ctr = addr_to_pipectr(dev_addr, ep_addr); + uint8_t rhport = 0; // FIXME change API + uint16_t volatile *ctr = addr_to_pipectr(rhport, dev_addr, ep_addr); TU_ASSERT(ctr); const uint32_t pid = *ctr & 0x3; @@ -756,67 +778,73 @@ bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) //--------------------------------------------------------------------+ void hcd_int_handler(uint8_t rhport) { - (void)rhport; -#if defined(__CCRX__) - static const int Mod37BitPosition[] = { - -1, 0, 1, 26, 2, 23, 27, 0, 3, 16, 24, 30, 28, 11, 0, 13, 4, - 7, 17, 0, 25, 22, 31, 15, 29, 10, 12, 6, 0, 21, 14, 9, 5, - 20, 8, 19, 18}; -#endif + rusb2_reg_t* rusb = RUSB2_REG(rhport); static unsigned char attach_attempt = 0; - unsigned is1 = RUSB2->INTSTS1; - unsigned is0 = RUSB2->INTSTS0; + unsigned is0 = rusb->INTSTS0; + unsigned is1 = rusb->INTSTS1; /* clear active bits except VALID (don't write 0 to already cleared bits according to the HW manual) */ - RUSB2->INTSTS1 = ~((RUSB2_INTSTS1_SACK_Msk | RUSB2_INTSTS1_SIGN_Msk | RUSB2_INTSTS1_ATTCH_Msk | RUSB2_INTSTS1_DTCH_Msk) & is1); - RUSB2->INTSTS0 = ~((RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_NRDY_Msk | RUSB2_INTSTS0_BEMP_Msk) & is0); - TU_LOG(TU_RUSB2_HCD_DBG, "IS %04x %04x\n", is0, is1); - is1 &= RUSB2->INTENB1; - is0 &= RUSB2->INTENB0; + rusb->INTSTS1 = ~((RUSB2_INTSTS1_SACK_Msk | RUSB2_INTSTS1_SIGN_Msk | RUSB2_INTSTS1_ATTCH_Msk | RUSB2_INTSTS1_DTCH_Msk) & is1); + rusb->INTSTS0 = ~((RUSB2_INTSTS0_BRDY_Msk | RUSB2_INTSTS0_NRDY_Msk | RUSB2_INTSTS0_BEMP_Msk) & is0); + + TU_LOG3("IS %04x %04x\n", is0, is1); + is1 &= rusb->INTENB1; + is0 &= rusb->INTENB0; if (is1 & RUSB2_INTSTS1_SACK_Msk) { /* Set DATA1 in advance for the next transfer. */ - RUSB2->DCPCTR_b.SQSET = 1; + rusb->DCPCTR_b.SQSET = 1; attach_attempt = 0; - hcd_event_xfer_complete(RUSB2->DCPMAXP_b.DEVSEL, tu_edpt_addr(0, TUSB_DIR_OUT), 8, XFER_RESULT_SUCCESS, true); + hcd_event_xfer_complete(rusb->DCPMAXP_b.DEVSEL, tu_edpt_addr(0, TUSB_DIR_OUT), 8, XFER_RESULT_SUCCESS, true); } + if (is1 & RUSB2_INTSTS1_SIGN_Msk) { - hcd_event_xfer_complete(RUSB2->DCPMAXP_b.DEVSEL, tu_edpt_addr(0, TUSB_DIR_OUT), 8, XFER_RESULT_FAILED, true); + hcd_event_xfer_complete(rusb->DCPMAXP_b.DEVSEL, tu_edpt_addr(0, TUSB_DIR_OUT), 8, XFER_RESULT_FAILED, true); if(attach_attempt > 0) { - RUSB2->DVSTCTR0_b.UACT = 1; + rusb->DVSTCTR0_b.UACT = 1; _hcd.need_reset = true; - RUSB2->INTENB1 = (RUSB2->INTENB1 & ~RUSB2_INTSTS1_ATTCH_Msk) | RUSB2_INTSTS1_DTCH_Msk; + rusb->INTENB1 = (rusb->INTENB1 & ~RUSB2_INTSTS1_ATTCH_Msk) | RUSB2_INTSTS1_DTCH_Msk; hcd_event_device_attach(rhport, true); } attach_attempt--; } + if (is1 & RUSB2_INTSTS1_ATTCH_Msk) { attach_attempt = 10; - RUSB2->DVSTCTR0_b.UACT = 1; + rusb->DVSTCTR0_b.UACT = 1; _hcd.need_reset = true; - RUSB2->INTENB1 = (RUSB2->INTENB1 & ~RUSB2_INTSTS1_ATTCH_Msk) | RUSB2_INTSTS1_DTCH_Msk; + rusb->INTENB1 = (rusb->INTENB1 & ~RUSB2_INTSTS1_ATTCH_Msk) | RUSB2_INTSTS1_DTCH_Msk; hcd_event_device_attach(rhport, true); } + if (is1 & RUSB2_INTSTS1_DTCH_Msk) { - RUSB2->DVSTCTR0_b.UACT = 0; - if (RUSB2->DCPCTR_b.SUREQ) { - RUSB2->DCPCTR_b.SUREQCLR = 1; + rusb->DVSTCTR0_b.UACT = 0; + if (rusb->DCPCTR_b.SUREQ) { + rusb->DCPCTR_b.SUREQCLR = 1; } - RUSB2->INTENB1 = (RUSB2->INTENB1 & ~RUSB2_INTSTS1_DTCH_Msk) | RUSB2_INTSTS1_ATTCH_Msk; + rusb->INTENB1 = (rusb->INTENB1 & ~RUSB2_INTSTS1_DTCH_Msk) | RUSB2_INTSTS1_ATTCH_Msk; hcd_event_device_remove(rhport, true); } if (is0 & RUSB2_INTSTS0_BEMP_Msk) { - const unsigned s = RUSB2->BEMPSTS; - RUSB2->BEMPSTS = 0; + const unsigned s = rusb->BEMPSTS; + rusb->BEMPSTS = 0; if (s & 1) { process_pipe0_bemp(rhport); } } + +#if defined(__CCRX__) + static const int Mod37BitPosition[] = { + -1, 0, 1, 26, 2, 23, 27, 0, 3, 16, 24, 30, 28, 11, 0, 13, 4, + 7, 17, 0, 25, 22, 31, 15, 29, 10, 12, 6, 0, 21, 14, 9, 5, + 20, 8, 19, 18}; +#endif + if (is0 & RUSB2_INTSTS0_NRDY_Msk) { - const unsigned m = RUSB2->NRDYENB; - unsigned s = RUSB2->NRDYSTS & m; - RUSB2->NRDYSTS = ~s; + const unsigned m = rusb->NRDYENB; + unsigned s = rusb->NRDYSTS & m; + rusb->NRDYSTS = ~s; while (s) { #if defined(__CCRX__) const unsigned num = Mod37BitPosition[(-s & s) % 37]; @@ -828,10 +856,10 @@ void hcd_int_handler(uint8_t rhport) } } if (is0 & RUSB2_INTSTS0_BRDY_Msk) { - const unsigned m = RUSB2->BRDYENB; - unsigned s = RUSB2->BRDYSTS & m; + const unsigned m = rusb->BRDYENB; + unsigned s = rusb->BRDYSTS & m; /* clear active bits (don't write 0 to already cleared bits according to the HW manual) */ - RUSB2->BRDYSTS = ~s; + rusb->BRDYSTS = ~s; while (s) { #if defined(__CCRX__) const unsigned num = Mod37BitPosition[(-s & s) % 37]; -- cgit v1.3.1 From c37a9571741cef0dcf0cd5a77e202ae741a2dd42 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 26 Jul 2023 19:56:48 +0700 Subject: correct hcd_edpt_clear_stall() API signature --- src/host/hcd.h | 2 +- src/portable/mentor/musb/hcd_musb.c | 4 ++-- src/portable/nxp/khci/hcd_khci.c | 4 ++-- src/portable/ohci/ohci.c | 4 ++-- src/portable/raspberrypi/pio_usb/hcd_pio_usb.c | 4 ++-- src/portable/raspberrypi/rp2040/hcd_rp2040.c | 4 ++-- src/portable/renesas/rusb2/hcd_rusb2.c | 4 ++-- 7 files changed, 13 insertions(+), 13 deletions(-) (limited to 'src/portable') diff --git a/src/host/hcd.h b/src/host/hcd.h index 50f1dcdcc..898e0c6a4 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -179,7 +179,7 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr); bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]); // clear stall, data toggle is also reset to DATA0 -bool hcd_edpt_clear_stall(uint8_t daddr, uint8_t ep_addr); +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t daddr, uint8_t ep_addr); //--------------------------------------------------------------------+ // USBH implemented API diff --git a/src/portable/mentor/musb/hcd_musb.c b/src/portable/mentor/musb/hcd_musb.c index 5be67a186..5d1fba6d9 100644 --- a/src/portable/mentor/musb/hcd_musb.c +++ b/src/portable/mentor/musb/hcd_musb.c @@ -831,8 +831,8 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { } // clear stall, data toggle is also reset to DATA0 -bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) -{ +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; unsigned const pipenum = find_pipe(dev_addr, ep_addr); if (!pipenum) return false; hw_endpoint_t volatile *regs = edpt_regs(pipenum - 1); diff --git a/src/portable/nxp/khci/hcd_khci.c b/src/portable/nxp/khci/hcd_khci.c index 6784049c5..928564e26 100644 --- a/src/portable/nxp/khci/hcd_khci.c +++ b/src/portable/nxp/khci/hcd_khci.c @@ -570,8 +570,8 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { return false; } -bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) -{ +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; if (!tu_edpt_number(ep_addr)) return true; int num = find_pipe(dev_addr, ep_addr); if (num < 0) return false; diff --git a/src/portable/ohci/ohci.c b/src/portable/ohci/ohci.c index 9f3af4781..413e72037 100644 --- a/src/portable/ohci/ohci.c +++ b/src/portable/ohci/ohci.c @@ -556,8 +556,8 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { return false; } -bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) -{ +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; ohci_ed_t * const p_ed = ed_from_addr(dev_addr, ep_addr); p_ed->is_stalled = 0; diff --git a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c index bb41ad638..45a3e80ef 100644 --- a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c +++ b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c @@ -163,8 +163,8 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet // return busy; //} -bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) -{ +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; (void) dev_addr; (void) ep_addr; diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 5091fa907..6db8e2a0a 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -625,8 +625,8 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet return true; } -bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) -{ +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; (void) dev_addr; (void) ep_addr; diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 0a75d0b47..292d40da8 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -718,8 +718,8 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { return false; } -bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) -{ +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; uint16_t volatile *ctr = addr_to_pipectr(dev_addr, ep_addr); TU_ASSERT(ctr); -- cgit v1.3.1 From 10575c1b380136ce9381393c33e982cea7ef4731 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 26 Jul 2023 20:48:18 +0700 Subject: mising ehci --- src/host/hcd.h | 2 +- src/portable/ehci/ehci.c | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) (limited to 'src/portable') diff --git a/src/host/hcd.h b/src/host/hcd.h index 898e0c6a4..d77dd6e2f 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -179,7 +179,7 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr); bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]); // clear stall, data toggle is also reset to DATA0 -bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t daddr, uint8_t ep_addr); +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr); //--------------------------------------------------------------------+ // USBH implemented API diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 241393a39..979069cfa 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -502,8 +502,8 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { return still_active; // true if removed an active transfer } -bool hcd_edpt_clear_stall(uint8_t daddr, uint8_t ep_addr) -{ +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t daddr, uint8_t ep_addr) { + (void) rhport; ehci_qhd_t *qhd = qhd_get_from_addr(daddr, ep_addr); qhd->qtd_overlay.halted = 0; hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); -- cgit v1.3.1 From 5a29db2787fea0ff9fe236d2631b2dcbc94aea50 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 27 Jul 2023 15:52:55 +0700 Subject: add check for edpt_xfer() with halted, also reset data toggle when clear stall --- src/portable/ehci/ehci.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index b84de5191..02b843667 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -443,6 +443,11 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * ehci_qtd_t* qtd; if (epnum == 0) { + // Control endpoint never be stalled. Skip reset Data Toggle since it is fixed per stage + if (qhd->qtd_overlay.halted) { + qhd->qtd_overlay.halted = false; + } + qtd = qtd_control(dev_addr); qtd_init(qtd, buffer, buflen); @@ -450,6 +455,9 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * qtd->data_toggle = 1; qtd->pid = dir ? EHCI_PID_IN : EHCI_PID_OUT; } else { + // skip if endpoint is halted + TU_VERIFY(!qhd->qtd_overlay.halted); + qtd = qtd_find_free(); TU_ASSERT(qtd); @@ -506,8 +514,9 @@ bool hcd_edpt_clear_stall(uint8_t daddr, uint8_t ep_addr) { ehci_qhd_t *qhd = qhd_get_from_addr(daddr, ep_addr); qhd->qtd_overlay.halted = 0; + qhd->qtd_overlay.data_toggle = 0; hcd_dcache_clean_invalidate(qhd, sizeof(ehci_qhd_t)); - // TODO reset data toggle ? + return true; } @@ -881,8 +890,10 @@ static void qhd_remove_qtd(ehci_qhd_t *qhd) { qhd->attached_qtd = NULL; qhd->attached_buffer = 0; + hcd_dcache_clean(qhd, sizeof(ehci_qhd_t)); qtd->used = 0; // free QTD + hcd_dcache_clean(qtd, sizeof(ehci_qtd_t)); } //--------------------------------------------------------------------+ -- cgit v1.3.1 From 6021803d584a95efac5bc10f89ed970b2c1fa60e Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 28 Jul 2023 11:33:26 +0700 Subject: fix ci --- src/portable/renesas/rusb2/dcd_rusb2.c | 13 ++++++------- src/portable/renesas/rusb2/rusb2_ra.h | 9 ++++++--- 2 files changed, 12 insertions(+), 10 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 83f0fdc4a..0380f36b9 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -49,17 +49,16 @@ #define D0FIFOCTR CFIFOCTR #define D0FIFOCTR_b CFIFOCTR_b #endif + + // Application API for setting IRQ number + void tud_int_set_irqnum(uint8_t rhport, int32_t irqnum) { + rusb2_controller[rhport].irqnum = irqnum; + } + #else #error "Unsupported MCU" #endif -//--------------------------------------------------------------------+ -// Application API for setting IRQ number -//--------------------------------------------------------------------+ -void tud_int_set_irqnum(uint8_t rhport, int32_t irqnum) { - rusb2_controller[rhport].irqnum = irqnum; -} - //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM //--------------------------------------------------------------------+ diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 8a4d2ad36..7ff272bbc 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -64,8 +64,14 @@ typedef struct { #if defined(BSP_MCU_GROUP_RA6M5) || defined(BSP_MCU_GROUP_RA6M3) || (BSP_CFG_MCU_PART_SERIES == 8) #define RUSB2_SUPPORT_HIGHSPEED #define RUSB2_CONTROLLER_COUNT 2 + + #define rusb2_is_highspeed_rhport(_p) (_p == 1) + #define rusb2_is_highspeed_reg(_reg) (_reg == RUSB2_REG(1)) #else #define RUSB2_CONTROLLER_COUNT 1 + + #define rusb2_is_highspeed_rhport(_p) (false) + #define rusb2_is_highspeed_reg(_reg) (false) #endif // USBFS_INT_IRQn and USBHS_USB_INT_RESUME_IRQn are generated by FSP @@ -78,9 +84,6 @@ static rusb2_controller_t rusb2_controller[] = { #define RUSB2_REG(_p) ((rusb2_reg_t*) rusb2_controller[_p].reg_base) -#define rusb2_is_highspeed_rhport(_p) (_p == 1) -#define rusb2_is_highspeed_reg(_reg) (_reg == RUSB2_REG(1)) - //--------------------------------------------------------------------+ // RUSB2 API //--------------------------------------------------------------------+ -- cgit v1.3.1 From e56d5443a8a87e932b22bc6315f30cd537fe0edf Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 28 Jul 2023 12:42:40 +0700 Subject: - revert usb address - more clean up --- src/portable/renesas/rusb2/dcd_rusb2.c | 6 +++--- src/portable/renesas/rusb2/hcd_rusb2.c | 14 ++++---------- 2 files changed, 7 insertions(+), 13 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 0380f36b9..9383923bd 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -51,7 +51,7 @@ #endif // Application API for setting IRQ number - void tud_int_set_irqnum(uint8_t rhport, int32_t irqnum) { + void tud_rusb2_set_irqnum(uint8_t rhport, int32_t irqnum) { rusb2_controller[rhport].irqnum = irqnum; } @@ -638,7 +638,7 @@ static void process_bus_reset(uint8_t rhport) static void process_set_address(uint8_t rhport) { rusb2_reg_t* rusb = RUSB2_REG(rhport); - const uint32_t addr = rusb->USBADDR & 0xFF; + const uint16_t addr = rusb->USBADDR_b.USBADDR; if (!addr) return; const tusb_control_request_t setup_packet = { @@ -821,7 +821,7 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * ep_desc) if ( rusb2_is_highspeed_rhport(rhport) ) { // FIXME shouldn't be after pipe selection and config, also the BUFNMB should be changed - // depending on the allocation scheme + // depending on the allocation scheme rusb->PIPEBUF = 0x7C08; } diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index fef8bdf19..c5ed8ae55 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -32,21 +32,15 @@ #include "host/hcd.h" #include "rusb2_type.h" -#if !defined(CFG_TUSB_RHPORT0_MODE) && !defined(CFG_TUSB_RHPORT1_MODE) -// fallback -#define CFG_TUSB_RHPORT0_MODE OPT_MODE_HOST -#define CFG_TUSB_RHPORT1_MODE 0 -#endif - #if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) #include "rusb2_rx.h" #elif TU_CHECK_MCU(OPT_MCU_RAXXX) #include "rusb2_ra.h" - void osal_task_delay(uint32_t msec) { - R_BSP_SoftwareDelay(msec, BSP_DELAY_UNITS_MILLISECONDS); - } +// void osal_task_delay(uint32_t msec) { +// R_BSP_SoftwareDelay(msec, BSP_DELAY_UNITS_MILLISECONDS); +// } #else #error "Unsupported MCU" @@ -785,7 +779,7 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { void hcd_int_handler(uint8_t rhport) { rusb2_reg_t* rusb = RUSB2_REG(rhport); - static unsigned char attach_attempt = 0; + static unsigned char attach_attempt = 0; // TODO remove later unsigned is0 = rusb->INTSTS0; unsigned is1 = rusb->INTSTS1; -- cgit v1.3.1 From feb58ebd54e68bc3b7f21b0d168417053c525f0a Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 28 Jul 2023 19:01:12 +0700 Subject: add uno r4 wih FLASH_IMAGE_START=0x4000, running but interrupt (systick) does not seems to work --- .idea/runConfigurations/ra4m1.xml | 2 +- .idea/runConfigurations/ra6m1.xml | 2 +- .idea/runConfigurations/ra6m5.xml | 2 +- .../ra4m1_ek/fsp_cfg/bsp/bsp_mcu_family_cfg.h | 18 ++--- hw/bsp/ra/boards/uno_r4/board.cmake | 11 +++ hw/bsp/ra/boards/uno_r4/board.h | 53 +++++++++++++ hw/bsp/ra/boards/uno_r4/board.mk | 9 +++ hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_cfg.h | 35 +++++++++ .../boards/uno_r4/fsp_cfg/bsp/bsp_mcu_device_cfg.h | 5 ++ .../uno_r4/fsp_cfg/bsp/bsp_mcu_device_pn_cfg.h | 11 +++ .../boards/uno_r4/fsp_cfg/bsp/bsp_mcu_family_cfg.h | 87 ++++++++++++++++++++++ hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp_clock_cfg.h | 21 ++++++ hw/bsp/ra/boards/uno_r4/uno_r4.ld | 25 +++++++ hw/bsp/ra/family.mk | 3 +- src/portable/renesas/rusb2/hcd_rusb2.c | 1 + 15 files changed, 272 insertions(+), 13 deletions(-) create mode 100644 hw/bsp/ra/boards/uno_r4/board.cmake create mode 100644 hw/bsp/ra/boards/uno_r4/board.h create mode 100644 hw/bsp/ra/boards/uno_r4/board.mk create mode 100644 hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_cfg.h create mode 100644 hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_device_cfg.h create mode 100644 hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_device_pn_cfg.h create mode 100644 hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_family_cfg.h create mode 100644 hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp_clock_cfg.h create mode 100644 hw/bsp/ra/boards/uno_r4/uno_r4.ld (limited to 'src/portable') diff --git a/.idea/runConfigurations/ra4m1.xml b/.idea/runConfigurations/ra4m1.xml index 22bb61949..149a157c4 100644 --- a/.idea/runConfigurations/ra4m1.xml +++ b/.idea/runConfigurations/ra4m1.xml @@ -1,5 +1,5 @@ - + diff --git a/.idea/runConfigurations/ra6m1.xml b/.idea/runConfigurations/ra6m1.xml index 438ac4063..57af9abd9 100644 --- a/.idea/runConfigurations/ra6m1.xml +++ b/.idea/runConfigurations/ra6m1.xml @@ -1,5 +1,5 @@ - + diff --git a/.idea/runConfigurations/ra6m5.xml b/.idea/runConfigurations/ra6m5.xml index 89f9787a0..1a6358304 100644 --- a/.idea/runConfigurations/ra6m5.xml +++ b/.idea/runConfigurations/ra6m5.xml @@ -1,5 +1,5 @@ - + diff --git a/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp/bsp_mcu_family_cfg.h b/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp/bsp_mcu_family_cfg.h index 3bde2db0d..72cdb89e6 100644 --- a/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp/bsp_mcu_family_cfg.h +++ b/hw/bsp/ra/boards/ra4m1_ek/fsp_cfg/bsp/bsp_mcu_family_cfg.h @@ -12,16 +12,16 @@ #define BSP_MOCO_HZ (8000000) #define BSP_SUB_CLOCK_HZ (32768) #if BSP_CFG_HOCO_FREQUENCY == 0 -#define BSP_HOCO_HZ (24000000) + #define BSP_HOCO_HZ (24000000) #elif BSP_CFG_HOCO_FREQUENCY == 2 - #define BSP_HOCO_HZ (32000000) - #elif BSP_CFG_HOCO_FREQUENCY == 4 - #define BSP_HOCO_HZ (48000000) - #elif BSP_CFG_HOCO_FREQUENCY == 5 - #define BSP_HOCO_HZ (64000000) - #else - #error "Invalid HOCO frequency chosen (BSP_CFG_HOCO_FREQUENCY) in bsp_clock_cfg.h" - #endif + #define BSP_HOCO_HZ (32000000) +#elif BSP_CFG_HOCO_FREQUENCY == 4 + #define BSP_HOCO_HZ (48000000) +#elif BSP_CFG_HOCO_FREQUENCY == 5 + #define BSP_HOCO_HZ (64000000) +#else + #error "Invalid HOCO frequency chosen (BSP_CFG_HOCO_FREQUENCY) in bsp_clock_cfg.h" +#endif #define BSP_CORTEX_VECTOR_TABLE_ENTRIES (16U) #define BSP_VECTOR_TABLE_MAX_ENTRIES (48U) diff --git a/hw/bsp/ra/boards/uno_r4/board.cmake b/hw/bsp/ra/boards/uno_r4/board.cmake new file mode 100644 index 000000000..34780d776 --- /dev/null +++ b/hw/bsp/ra/boards/uno_r4/board.cmake @@ -0,0 +1,11 @@ +set(CMAKE_SYSTEM_PROCESSOR cortex-m4 CACHE INTERNAL "System Processor") +set(MCU_VARIANT ra4m1) + +set(JLINK_DEVICE R7FA4M1AB) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/${BOARD}.ld) + +function(update_board TARGET) +# target_compile_definitions(${TARGET} PUBLIC) +# target_sources(${TARGET} PRIVATE) +# target_include_directories(${BOARD_TARGET} PUBLIC) +endfunction() diff --git a/hw/bsp/ra/boards/uno_r4/board.h b/hw/bsp/ra/boards/uno_r4/board.h new file mode 100644 index 000000000..72abda27f --- /dev/null +++ b/hw/bsp/ra/boards/uno_r4/board.h @@ -0,0 +1,53 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _BOARD_H_ +#define _BOARD_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +#define LED1 BSP_IO_PORT_01_PIN_11 // D13 +#define LED_STATE_ON 1 + +#define SW1 BSP_IO_PORT_01_PIN_10 // D12 +#define BUTTON_STATE_ACTIVE 0 + +static const ioport_pin_cfg_t board_pin_cfg[] = { + {.pin = LED1, .pin_cfg = IOPORT_CFG_PORT_DIRECTION_OUTPUT}, + {.pin = SW1, .pin_cfg = IOPORT_CFG_PORT_DIRECTION_INPUT}, + // USB FS D+, D-, VBus + {.pin = BSP_IO_PORT_04_PIN_07, .pin_cfg = IOPORT_CFG_PERIPHERAL_PIN | IOPORT_PERIPHERAL_USB_FS}, + {.pin = BSP_IO_PORT_09_PIN_14, .pin_cfg = IOPORT_CFG_PERIPHERAL_PIN | IOPORT_PERIPHERAL_USB_FS}, + {.pin = BSP_IO_PORT_09_PIN_15, .pin_cfg = IOPORT_CFG_PERIPHERAL_PIN | IOPORT_PERIPHERAL_USB_FS}, +}; + +#ifdef __cplusplus +} +#endif + +#endif diff --git a/hw/bsp/ra/boards/uno_r4/board.mk b/hw/bsp/ra/boards/uno_r4/board.mk new file mode 100644 index 000000000..cbe6c782c --- /dev/null +++ b/hw/bsp/ra/boards/uno_r4/board.mk @@ -0,0 +1,9 @@ +CPU_CORE = cortex-m4 +MCU_VARIANT = ra4m1 + +LD_FILE = $(BOARD_PATH)/${BOARD}.ld + +# For flash-jlink target +JLINK_DEVICE = R7FA4M1AB + +flash: flash-jlink diff --git a/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_cfg.h b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_cfg.h new file mode 100644 index 000000000..c1d1022cc --- /dev/null +++ b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_cfg.h @@ -0,0 +1,35 @@ +/* generated configuration header file - do not edit */ +#ifndef BSP_CFG_H_ +#define BSP_CFG_H_ + +#include "bsp_clock_cfg.h" +#include "bsp_mcu_family_cfg.h" +#include "board_cfg.h" + +#undef RA_NOT_DEFINED +#define BSP_CFG_RTOS (0) +#if defined(_RA_BOOT_IMAGE) +#define BSP_CFG_BOOT_IMAGE (1) +#endif +#define BSP_CFG_MCU_VCC_MV (3300) +#define BSP_CFG_STACK_MAIN_BYTES (0x800) +#define BSP_CFG_HEAP_BYTES (0x1000) +#define BSP_CFG_PARAM_CHECKING_ENABLE (1) +#define BSP_CFG_ASSERT (0) +#define BSP_CFG_ERROR_LOG (0) + +#define BSP_CFG_PFS_PROTECT ((1)) + +#define BSP_CFG_C_RUNTIME_INIT ((1)) +#define BSP_CFG_EARLY_INIT ((0)) + +#define BSP_CFG_STARTUP_CLOCK_REG_NOT_RESET ((0)) + +#define BSP_CLOCK_CFG_MAIN_OSC_POPULATED (0) + +#define BSP_CLOCK_CFG_MAIN_OSC_CLOCK_SOURCE (0) +#define BSP_CLOCK_CFG_SUBCLOCK_DRIVE (0) +#define BSP_CLOCK_CFG_SUBCLOCK_POPULATED (0) +#define BSP_CLOCK_CFG_SUBCLOCK_STABILIZATION_MS 1000 + +#endif /* BSP_CFG_H_ */ diff --git a/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_device_cfg.h b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_device_cfg.h new file mode 100644 index 000000000..444d32e56 --- /dev/null +++ b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_device_cfg.h @@ -0,0 +1,5 @@ +/* generated configuration header file - do not edit */ +#ifndef BSP_MCU_DEVICE_CFG_H_ +#define BSP_MCU_DEVICE_CFG_H_ +#define BSP_CFG_MCU_PART_SERIES (4) +#endif /* BSP_MCU_DEVICE_CFG_H_ */ diff --git a/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_device_pn_cfg.h b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_device_pn_cfg.h new file mode 100644 index 000000000..336918800 --- /dev/null +++ b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_device_pn_cfg.h @@ -0,0 +1,11 @@ +/* generated configuration header file - do not edit */ +#ifndef BSP_MCU_DEVICE_PN_CFG_H_ +#define BSP_MCU_DEVICE_PN_CFG_H_ +#define BSP_MCU_R7FA4M1AB3CNE +#define BSP_MCU_FEATURE_SET ('A') +#define BSP_ROM_SIZE_BYTES (262144) +#define BSP_RAM_SIZE_BYTES (32768) +#define BSP_DATA_FLASH_SIZE_BYTES (8192) +#define BSP_PACKAGE_QFN +#define BSP_PACKAGE_PINS (48) +#endif /* BSP_MCU_DEVICE_PN_CFG_H_ */ diff --git a/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_family_cfg.h b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_family_cfg.h new file mode 100644 index 000000000..fc604eb3b --- /dev/null +++ b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp/bsp_mcu_family_cfg.h @@ -0,0 +1,87 @@ +/* generated configuration header file through renesas e2 studio */ +#ifndef BSP_MCU_FAMILY_CFG_H_ +#define BSP_MCU_FAMILY_CFG_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +#include "bsp_mcu_device_pn_cfg.h" +#include "bsp_mcu_device_cfg.h" +#include "bsp_mcu_info.h" +#include "bsp_clock_cfg.h" + +#define BSP_MCU_GROUP_RA4M1 (1) +#define BSP_LOCO_HZ (32768) +#define BSP_MOCO_HZ (8000000) +#define BSP_SUB_CLOCK_HZ (32768) +#if BSP_CFG_HOCO_FREQUENCY == 0 + #define BSP_HOCO_HZ (24000000) +#elif BSP_CFG_HOCO_FREQUENCY == 2 + #define BSP_HOCO_HZ (32000000) +#elif BSP_CFG_HOCO_FREQUENCY == 4 + #define BSP_HOCO_HZ (48000000) +#elif BSP_CFG_HOCO_FREQUENCY == 5 + #define BSP_HOCO_HZ (64000000) +#else + #error "Invalid HOCO frequency chosen (BSP_CFG_HOCO_FREQUENCY) in bsp_clock_cfg.h" +#endif +#define BSP_CORTEX_VECTOR_TABLE_ENTRIES (16U) +#define BSP_VECTOR_TABLE_MAX_ENTRIES (48U) +#define BSP_MCU_VBATT_SUPPORT (1) + +#define OFS_SEQ1 0xA001A001 | (1 << 1) | (3 << 2) +#define OFS_SEQ2 (15 << 4) | (3 << 8) | (3 << 10) +#define OFS_SEQ3 (1 << 12) | (1 << 14) | (1 << 17) +#define OFS_SEQ4 (3 << 18) |(15 << 20) | (3 << 24) | (3 << 26) +#define OFS_SEQ5 (1 << 28) | (1 << 30) +#define BSP_CFG_ROM_REG_OFS0 (OFS_SEQ1 | OFS_SEQ2 | OFS_SEQ3 | OFS_SEQ4 | OFS_SEQ5) +#define BSP_CFG_ROM_REG_OFS1 (0xFFFFFEC3 | (1 << 2) | (3 << 3) | (0 << 8)) +#define BSP_CFG_USE_LOW_VOLTAGE_MODE ((0)) +#define BSP_CFG_ROM_REG_MPU_PC0_ENABLE (1) +#define BSP_CFG_ROM_REG_MPU_PC0_START (0x00FFFFFC) +#define BSP_CFG_ROM_REG_MPU_PC0_END (0x00FFFFFF) +#define BSP_CFG_ROM_REG_MPU_PC1_ENABLE (1) +#define BSP_CFG_ROM_REG_MPU_PC1_START (0x00FFFFFC) +#define BSP_CFG_ROM_REG_MPU_PC1_END (0x00FFFFFF) +#define BSP_CFG_ROM_REG_MPU_REGION0_ENABLE (1) +#define BSP_CFG_ROM_REG_MPU_REGION0_START (0x00FFFFFC) +#define BSP_CFG_ROM_REG_MPU_REGION0_END (0x00FFFFFF) +#define BSP_CFG_ROM_REG_MPU_REGION1_ENABLE (1) +#define BSP_CFG_ROM_REG_MPU_REGION1_START (0x200FFFFC) +#define BSP_CFG_ROM_REG_MPU_REGION1_END (0x200FFFFF) +#define BSP_CFG_ROM_REG_MPU_REGION2_ENABLE (1) +#define BSP_CFG_ROM_REG_MPU_REGION2_START (0x407FFFFC) +#define BSP_CFG_ROM_REG_MPU_REGION2_END (0x407FFFFF) +#define BSP_CFG_ROM_REG_MPU_REGION3_ENABLE (1) +#define BSP_CFG_ROM_REG_MPU_REGION3_START (0x400DFFFC) +#define BSP_CFG_ROM_REG_MPU_REGION3_END (0x400DFFFF) +#ifndef BSP_CLOCK_CFG_MAIN_OSC_WAIT +#define BSP_CLOCK_CFG_MAIN_OSC_WAIT (9) +#endif +/* Used to create IELS values for the interrupt initialization table g_interrupt_event_link_select. */ +#define BSP_PRV_IELS_ENUM(vector) (ELC_ ## vector) + +/* + ID Code + Note: To permanently lock and disable the debug interface define the BSP_ID_CODE_PERMANENTLY_LOCKED in the compiler settings. + WARNING: This will disable debug access to the part and cannot be reversed by a debug probe. + */ +#if defined(BSP_ID_CODE_PERMANENTLY_LOCKED) + #define BSP_CFG_ID_CODE_LONG_1 (0x00000000) + #define BSP_CFG_ID_CODE_LONG_2 (0x00000000) + #define BSP_CFG_ID_CODE_LONG_3 (0x00000000) + #define BSP_CFG_ID_CODE_LONG_4 (0x00000000) + #else +/* ID CODE: FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF */ +#define BSP_CFG_ID_CODE_LONG_1 (0xFFFFFFFF) +#define BSP_CFG_ID_CODE_LONG_2 (0xFFFFFFFF) +#define BSP_CFG_ID_CODE_LONG_3 (0xFFFFFFFF) +#define BSP_CFG_ID_CODE_LONG_4 (0xffFFFFFF) +#endif + +#ifdef __cplusplus +} +#endif + +#endif /* BSP_MCU_FAMILY_CFG_H_ */ diff --git a/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp_clock_cfg.h b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp_clock_cfg.h new file mode 100644 index 000000000..63618ec4b --- /dev/null +++ b/hw/bsp/ra/boards/uno_r4/fsp_cfg/bsp_clock_cfg.h @@ -0,0 +1,21 @@ +/* generated configuration header file - do not edit */ +#ifndef BSP_CLOCK_CFG_H_ +#define BSP_CLOCK_CFG_H_ +#define BSP_CFG_CLOCKS_SECURE (0) +#define BSP_CFG_CLOCKS_OVERRIDE (0) +#define BSP_CFG_XTAL_HZ (0) /* XTAL 0Hz */ +#define BSP_CFG_PLL_SOURCE (BSP_CLOCKS_CLOCK_DISABLED) /* PLL Src: XTAL */ +#define BSP_CFG_HOCO_FREQUENCY (4) /* HOCO 48MHz */ +#define BSP_CFG_PLL_DIV (BSP_CLOCKS_PLL_DIV_4) /* PLL Div /4 */ +#define BSP_CFG_PLL_MUL BSP_CLOCKS_PLL_MUL(12, 0) /* PLL Mul x12 */ +#define BSP_CFG_CLOCK_SOURCE (BSP_CLOCKS_SOURCE_CLOCK_HOCO) /* Clock Src: HOCO */ +#define BSP_CFG_ICLK_DIV (BSP_CLOCKS_SYS_CLOCK_DIV_1) /* ICLK Div /1 */ +#define BSP_CFG_PCLKA_DIV (BSP_CLOCKS_SYS_CLOCK_DIV_1) /* PCLKA Div /1 */ +#define BSP_CFG_PCLKB_DIV (BSP_CLOCKS_SYS_CLOCK_DIV_2) /* PCLKB Div /2 */ +#define BSP_CFG_PCLKC_DIV (BSP_CLOCKS_SYS_CLOCK_DIV_1) /* PCLKC Div /1 */ +#define BSP_CFG_PCLKD_DIV (BSP_CLOCKS_SYS_CLOCK_DIV_1) /* PCLKD Div /1 */ +#define BSP_CFG_FCLK_DIV (BSP_CLOCKS_SYS_CLOCK_DIV_2) /* FCLK Div /2 */ +#define BSP_CFG_CLKOUT_SOURCE (BSP_CLOCKS_CLOCK_DISABLED) /* CLKOUT Src: SUBCLK */ +#define BSP_CFG_CLKOUT_DIV (BSP_CLOCKS_SYS_CLOCK_DIV_1) /* CLKOUT Div /1 */ +#define BSP_CFG_UCK_SOURCE (BSP_CLOCKS_SOURCE_CLOCK_HOCO) /* UCLK Src: HOCO */ +#endif /* BSP_CLOCK_CFG_H_ */ diff --git a/hw/bsp/ra/boards/uno_r4/uno_r4.ld b/hw/bsp/ra/boards/uno_r4/uno_r4.ld new file mode 100644 index 000000000..45f11dfb1 --- /dev/null +++ b/hw/bsp/ra/boards/uno_r4/uno_r4.ld @@ -0,0 +1,25 @@ +RAM_START = 0x20000000; +RAM_LENGTH = 0x8000; +FLASH_START = 0x00000000; +FLASH_LENGTH = 0x40000; +DATA_FLASH_START = 0x40100000; +DATA_FLASH_LENGTH = 0x2000; +OPTION_SETTING_START = 0x00000000; +OPTION_SETTING_LENGTH = 0x0; +OPTION_SETTING_S_START = 0x80000000; +OPTION_SETTING_S_LENGTH = 0x0; +ID_CODE_START = 0x01010018; +ID_CODE_LENGTH = 0x20; +SDRAM_START = 0x80010000; +SDRAM_LENGTH = 0x0; +QSPI_FLASH_START = 0x60000000; +QSPI_FLASH_LENGTH = 0x0; +OSPI_DEVICE_0_START = 0x80020000; +OSPI_DEVICE_0_LENGTH = 0x0; +OSPI_DEVICE_1_START = 0x80030000; +OSPI_DEVICE_1_LENGTH = 0x0; + +/* Uno R4 has bootloader */ +FLASH_IMAGE_START = 0x4000; + +INCLUDE fsp.ld diff --git a/hw/bsp/ra/family.mk b/hw/bsp/ra/family.mk index f5097460a..a5325306d 100644 --- a/hw/bsp/ra/family.mk +++ b/hw/bsp/ra/family.mk @@ -59,9 +59,10 @@ INC += \ ifndef LD_FILE LD_FILE = $(FAMILY_PATH)/linker/gcc/$(MCU_VARIANT).ld -LDFLAGS += -L$(TOP)/$(FAMILY_PATH)/linker/gcc endif +LDFLAGS += -L$(TOP)/$(FAMILY_PATH)/linker/gcc + # For freeRTOS port source # hack to use the port provided by renesas FREERTOS_PORTABLE_SRC = $(FSP_RA)/src/rm_freertos_port diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index c5ed8ae55..7f49dc8a9 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -186,6 +186,7 @@ static inline void pipe_wait_for_ready(rusb2_reg_t* rusb, unsigned num) static void pipe_write_packet(void *buf, volatile void *fifo, unsigned len) { + // NOTE: unlike DCD, Highspeed 32-bit FIFO does not need to adjust the fifo address volatile hw_fifo_t *reg = (volatile hw_fifo_t*)fifo; uintptr_t addr = (uintptr_t)buf; while (len >= 2) { -- cgit v1.3.1 From 0d9973ef87a55276d14c2aa45647f92a8358e9a2 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 31 Jul 2023 16:21:19 +0700 Subject: enable_irq since uno bootloader can disable it. systick triggered, however usb still not work with uno --- hw/bsp/ra/family.c | 4 ++++ src/portable/renesas/rusb2/dcd_rusb2.c | 1 + 2 files changed, 5 insertions(+) (limited to 'src/portable') diff --git a/hw/bsp/ra/family.c b/hw/bsp/ra/family.c index b78fdedc7..096f0d0ff 100644 --- a/hw/bsp/ra/family.c +++ b/hw/bsp/ra/family.c @@ -92,6 +92,10 @@ const bsp_interrupt_event_t g_interrupt_event_link_select[BSP_ICU_VECTOR_MAX_ENT //--------------------------------------------------------------------+ void board_init(void) { + // Enable global interrupts in CPSR register since board with bootloader such as Arduino Uno R4 + // can transfer CPU control with CPSR.I bit set to 0 (disable IRQ) + __enable_irq(); + /* Configure pins. */ R_IOPORT_Open(&port_ctrl, &family_pin_cfg); diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 9383923bd..37fd93497 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -740,6 +740,7 @@ void dcd_init(uint8_t rhport) rusb->BEMPENB = 1; rusb->BRDYENB = 1; + // If VBUS (detect) pin is not used, application need to call tud_connect() manually after tud_init() if (rusb->INTSTS0_b.VBSTS) { dcd_connect(rhport); } -- cgit v1.3.1 From 3f788a4e5a7758ce51cbcadef4ac21e427cc3c56 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 31 Jul 2023 19:09:40 +0700 Subject: enable USBMC for uno r4, add board_init_after_tusb() API add BOARD_UPPERCASE for board detection --- examples/device/audio_4_channel_mic/src/main.c | 4 ++++ examples/device/audio_test/src/main.c | 4 ++++ examples/device/audio_test_multi_rate/src/main.c | 4 ++++ examples/device/cdc_dual_ports/src/main.c | 4 ++++ examples/device/cdc_msc/src/main.c | 4 ++++ examples/device/cdc_msc_freertos/src/main.c | 4 ++++ examples/device/dfu/src/main.c | 4 ++++ examples/device/dfu_runtime/src/main.c | 4 ++++ examples/device/dynamic_configuration/src/main.c | 4 ++++ examples/device/hid_boot_interface/src/main.c | 4 ++++ examples/device/hid_composite/src/main.c | 4 ++++ examples/device/hid_composite_freertos/src/main.c | 4 ++++ examples/device/hid_generic_inout/src/main.c | 4 ++++ examples/device/hid_multiple_interface/src/main.c | 4 ++++ examples/device/midi_test/src/main.c | 4 ++++ examples/device/msc_dual_lun/src/main.c | 4 ++++ examples/device/net_lwip_webserver/src/main.c | 4 ++++ examples/device/uac2_headset/src/main.c | 4 ++++ examples/device/usbtmc/src/main.c | 4 ++++ examples/device/video_capture/src/main.c | 4 ++++ examples/device/webusb_serial/src/main.c | 4 ++++ examples/dual/host_hid_to_device_cdc/src/main.c | 4 ++++ examples/host/bare_api/src/main.c | 4 ++++ examples/host/cdc_msc_hid/src/main.c | 4 ++++ examples/host/hid_controller/src/main.c | 4 ++++ examples/host/msc_file_explorer/src/main.c | 5 +++++ examples/make.mk | 2 ++ hw/bsp/board.h | 3 +++ hw/bsp/family_support.cmake | 5 +++++ hw/bsp/ra/boards/uno_r4/board.mk | 2 +- hw/bsp/ra/family.c | 7 +++++++ src/portable/renesas/rusb2/dcd_rusb2.c | 2 -- 32 files changed, 123 insertions(+), 3 deletions(-) (limited to 'src/portable') diff --git a/examples/device/audio_4_channel_mic/src/main.c b/examples/device/audio_4_channel_mic/src/main.c index 2b9c5143d..f5fc884bd 100644 --- a/examples/device/audio_4_channel_mic/src/main.c +++ b/examples/device/audio_4_channel_mic/src/main.c @@ -84,6 +84,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + // Init values sampFreq = AUDIO_SAMPLE_RATE; clkValid = 1; diff --git a/examples/device/audio_test/src/main.c b/examples/device/audio_test/src/main.c index b5ca41d36..6dc655416 100644 --- a/examples/device/audio_test/src/main.c +++ b/examples/device/audio_test/src/main.c @@ -85,6 +85,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + // Init values sampFreq = AUDIO_SAMPLE_RATE; clkValid = 1; diff --git a/examples/device/audio_test_multi_rate/src/main.c b/examples/device/audio_test_multi_rate/src/main.c index 078e783eb..637be2d40 100644 --- a/examples/device/audio_test_multi_rate/src/main.c +++ b/examples/device/audio_test_multi_rate/src/main.c @@ -99,6 +99,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + // Init values sampFreq = sampleRatesList[0]; clkValid = 1; diff --git a/examples/device/cdc_dual_ports/src/main.c b/examples/device/cdc_dual_ports/src/main.c index 70eaea85d..7ceff73b3 100644 --- a/examples/device/cdc_dual_ports/src/main.c +++ b/examples/device/cdc_dual_ports/src/main.c @@ -42,6 +42,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/cdc_msc/src/main.c b/examples/device/cdc_msc/src/main.c index 6dad73cbf..87fc33181 100644 --- a/examples/device/cdc_msc/src/main.c +++ b/examples/device/cdc_msc/src/main.c @@ -58,6 +58,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/cdc_msc_freertos/src/main.c b/examples/device/cdc_msc_freertos/src/main.c index 0e8a24d02..6cfef9ef5 100644 --- a/examples/device/cdc_msc_freertos/src/main.c +++ b/examples/device/cdc_msc_freertos/src/main.c @@ -136,6 +136,10 @@ void usb_device_task(void* param) // Otherwise it could cause kernel issue since USB IRQ handler does use RTOS queue API. tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + // RTOS forever loop while (1) { diff --git a/examples/device/dfu/src/main.c b/examples/device/dfu/src/main.c index 5f37f25e1..bcd5b4942 100644 --- a/examples/device/dfu/src/main.c +++ b/examples/device/dfu/src/main.c @@ -77,6 +77,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/dfu_runtime/src/main.c b/examples/device/dfu_runtime/src/main.c index 4ec3cb188..beef1037d 100644 --- a/examples/device/dfu_runtime/src/main.c +++ b/examples/device/dfu_runtime/src/main.c @@ -72,6 +72,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/dynamic_configuration/src/main.c b/examples/device/dynamic_configuration/src/main.c index 578f01d8c..6c7789138 100644 --- a/examples/device/dynamic_configuration/src/main.c +++ b/examples/device/dynamic_configuration/src/main.c @@ -59,6 +59,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/hid_boot_interface/src/main.c b/examples/device/hid_boot_interface/src/main.c index 1a155996a..47f68f8fa 100644 --- a/examples/device/hid_boot_interface/src/main.c +++ b/examples/device/hid_boot_interface/src/main.c @@ -59,6 +59,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/hid_composite/src/main.c b/examples/device/hid_composite/src/main.c index 8d0e6bece..d4c5f5b3e 100644 --- a/examples/device/hid_composite/src/main.c +++ b/examples/device/hid_composite/src/main.c @@ -60,6 +60,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/hid_composite_freertos/src/main.c b/examples/device/hid_composite_freertos/src/main.c index ca02af100..bdbe26b86 100644 --- a/examples/device/hid_composite_freertos/src/main.c +++ b/examples/device/hid_composite_freertos/src/main.c @@ -138,6 +138,10 @@ void usb_device_task(void* param) // Otherwise it could cause kernel issue since USB IRQ handler does use RTOS queue API. tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + // RTOS forever loop while (1) { diff --git a/examples/device/hid_generic_inout/src/main.c b/examples/device/hid_generic_inout/src/main.c index 5db8f5581..5b3e53b06 100644 --- a/examples/device/hid_generic_inout/src/main.c +++ b/examples/device/hid_generic_inout/src/main.c @@ -83,6 +83,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/hid_multiple_interface/src/main.c b/examples/device/hid_multiple_interface/src/main.c index 72240b208..94f845a84 100644 --- a/examples/device/hid_multiple_interface/src/main.c +++ b/examples/device/hid_multiple_interface/src/main.c @@ -64,6 +64,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/midi_test/src/main.c b/examples/device/midi_test/src/main.c index 2c3e9d954..c77207ca2 100644 --- a/examples/device/midi_test/src/main.c +++ b/examples/device/midi_test/src/main.c @@ -65,6 +65,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/msc_dual_lun/src/main.c b/examples/device/msc_dual_lun/src/main.c index c7f6de7bf..d8abb5151 100644 --- a/examples/device/msc_dual_lun/src/main.c +++ b/examples/device/msc_dual_lun/src/main.c @@ -57,6 +57,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/net_lwip_webserver/src/main.c b/examples/device/net_lwip_webserver/src/main.c index 19a0eae9d..22543880e 100644 --- a/examples/device/net_lwip_webserver/src/main.c +++ b/examples/device/net_lwip_webserver/src/main.c @@ -232,6 +232,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + /* initialize lwip, dhcp-server, dns-server, and http */ init_lwip(); while (!netif_is_up(&netif_data)); diff --git a/examples/device/uac2_headset/src/main.c b/examples/device/uac2_headset/src/main.c index 19a3f7bae..c502eb10d 100644 --- a/examples/device/uac2_headset/src/main.c +++ b/examples/device/uac2_headset/src/main.c @@ -105,6 +105,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + TU_LOG1("Headset running\r\n"); while (1) diff --git a/examples/device/usbtmc/src/main.c b/examples/device/usbtmc/src/main.c index 2bba336f1..fa7de7570 100644 --- a/examples/device/usbtmc/src/main.c +++ b/examples/device/usbtmc/src/main.c @@ -57,6 +57,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/video_capture/src/main.c b/examples/device/video_capture/src/main.c index 5654e0b61..b942dd30e 100644 --- a/examples/device/video_capture/src/main.c +++ b/examples/device/video_capture/src/main.c @@ -59,6 +59,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/device/webusb_serial/src/main.c b/examples/device/webusb_serial/src/main.c index eaca78c73..f63d0ccea 100644 --- a/examples/device/webusb_serial/src/main.c +++ b/examples/device/webusb_serial/src/main.c @@ -96,6 +96,10 @@ int main(void) // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/dual/host_hid_to_device_cdc/src/main.c b/examples/dual/host_hid_to_device_cdc/src/main.c index 817c63c70..5a31b9dda 100644 --- a/examples/dual/host_hid_to_device_cdc/src/main.c +++ b/examples/dual/host_hid_to_device_cdc/src/main.c @@ -83,6 +83,10 @@ int main(void) tud_init(BOARD_TUD_RHPORT); tuh_init(BOARD_TUH_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { tud_task(); // tinyusb device task diff --git a/examples/host/bare_api/src/main.c b/examples/host/bare_api/src/main.c index bb7fa850e..7286befe0 100644 --- a/examples/host/bare_api/src/main.c +++ b/examples/host/bare_api/src/main.c @@ -67,6 +67,10 @@ int main(void) // init host stack on configured roothub port tuh_init(BOARD_TUH_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { // tinyusb host task diff --git a/examples/host/cdc_msc_hid/src/main.c b/examples/host/cdc_msc_hid/src/main.c index 1f4acb822..51251be5c 100644 --- a/examples/host/cdc_msc_hid/src/main.c +++ b/examples/host/cdc_msc_hid/src/main.c @@ -48,6 +48,10 @@ int main(void) // init host stack on configured roothub port tuh_init(BOARD_TUH_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { // tinyusb host task diff --git a/examples/host/hid_controller/src/main.c b/examples/host/hid_controller/src/main.c index 4dcc92587..a4ab2f711 100644 --- a/examples/host/hid_controller/src/main.c +++ b/examples/host/hid_controller/src/main.c @@ -54,6 +54,10 @@ int main(void) // init host stack on configured roothub port tuh_init(BOARD_TUH_RHPORT); + if (board_init_after_tusb) { + board_init_after_tusb(); + } + while (1) { // tinyusb host task diff --git a/examples/host/msc_file_explorer/src/main.c b/examples/host/msc_file_explorer/src/main.c index 7b1c2ef27..fc4b4e669 100644 --- a/examples/host/msc_file_explorer/src/main.c +++ b/examples/host/msc_file_explorer/src/main.c @@ -80,6 +80,11 @@ int main(void) // init host stack on configured roothub port tuh_init(BOARD_TUH_RHPORT); + + if (board_init_after_tusb) { + board_init_after_tusb(); + } + msc_app_init(); while (1) diff --git a/examples/make.mk b/examples/make.mk index 3c3a920cc..4001a5359 100644 --- a/examples/make.mk +++ b/examples/make.mk @@ -116,6 +116,8 @@ INC += \ $(TOP)/$(FAMILY_PATH) \ $(TOP)/src \ +BOARD_UPPER = $(shell echo $(BOARD) | tr a-z A-Z) +CFLAGS += -DBOARD_$(BOARD_UPPER) # Log level is mapped to TUSB DEBUG option ifneq ($(LOG),) diff --git a/hw/bsp/board.h b/hw/bsp/board.h index 036556731..d782013bb 100644 --- a/hw/bsp/board.h +++ b/hw/bsp/board.h @@ -54,6 +54,9 @@ // Initialize on-board peripherals : led, button, uart and USB void board_init(void); +// Init board after tinyusb is initialized +void board_init_after_tusb(void) TU_ATTR_WEAK; + // Turn LED on or off void board_led_write(bool state); diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index d8298c8ad..db1ce988e 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -181,6 +181,11 @@ endfunction() function(family_configure_common TARGET RTOS) family_add_rtos(${TARGET} ${RTOS}) + string(TOUPPER ${BOARD} BOARD_UPPER) + target_compile_definitions(${TARGET} PUBLIC + BOARD_${BOARD_UPPER} + ) + # run size after build add_custom_command(TARGET ${TARGET} POST_BUILD COMMAND ${CMAKE_SIZE} $ diff --git a/hw/bsp/ra/boards/uno_r4/board.mk b/hw/bsp/ra/boards/uno_r4/board.mk index cbe6c782c..b7075eec0 100644 --- a/hw/bsp/ra/boards/uno_r4/board.mk +++ b/hw/bsp/ra/boards/uno_r4/board.mk @@ -1,7 +1,7 @@ CPU_CORE = cortex-m4 MCU_VARIANT = ra4m1 -LD_FILE = $(BOARD_PATH)/${BOARD}.ld +LD_FILE = ${BOARD_PATH}/${BOARD}.ld # For flash-jlink target JLINK_DEVICE = R7FA4M1AB diff --git a/hw/bsp/ra/family.c b/hw/bsp/ra/family.c index 096f0d0ff..e6213061d 100644 --- a/hw/bsp/ra/family.c +++ b/hw/bsp/ra/family.c @@ -124,6 +124,13 @@ void board_init(void) { board_led_write(false); } +void board_init_after_tusb(void) { + // For board that use USB LDO regulator +#if defined(BOARD_UNO_R4) + R_USB_FS0->USBMC |= R_USB_FS0_USBMC_VDCEN_Msk; +#endif +} + void board_led_write(bool state) { R_IOPORT_PinWrite(&port_ctrl, LED1, state ? LED_STATE_ON : !LED_STATE_ON); } diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 37fd93497..9a3983f56 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -726,8 +726,6 @@ void dcd_init(uint8_t rhport) rusb->PHYSLEW = 0x5; rusb->DPUSR0R_FS_b.FIXPHY0 = 0u; /* USB_BASE Transceiver Output fixed */ - - // rusb2->USBMC = (uint16_t) (rusb2->USBMC | RUSB2_USBMC_VDCEN_Msk); } /* Setup default control pipe */ -- cgit v1.3.1 From 965627e81c63a76bb80d8319cbd9adf931a00595 Mon Sep 17 00:00:00 2001 From: Martino Facchin Date: Tue, 1 Aug 2023 11:41:33 +0200 Subject: rusb2: move dynamic irq function to c file --- hw/bsp/ra/family.cmake | 5 +++-- hw/bsp/ra/family.mk | 1 + src/portable/renesas/rusb2/dcd_rusb2.c | 5 ----- src/portable/renesas/rusb2/rusb2_ra.c | 16 ++++++++++++++++ src/portable/renesas/rusb2/rusb2_ra.h | 9 +-------- 5 files changed, 21 insertions(+), 15 deletions(-) create mode 100644 src/portable/renesas/rusb2/rusb2_ra.c (limited to 'src/portable') diff --git a/hw/bsp/ra/family.cmake b/hw/bsp/ra/family.cmake index 307e01da8..2d079dc94 100644 --- a/hw/bsp/ra/family.cmake +++ b/hw/bsp/ra/family.cmake @@ -114,8 +114,9 @@ function(family_configure_example TARGET RTOS) # Add TinyUSB target and port source family_add_tinyusb(${TARGET} OPT_MCU_RAXXX ${RTOS}) target_sources(${TARGET}-tinyusb PUBLIC - ${TOP}/src/portable/renesas/rusb2/dcd_rusb2.c - ${TOP}/src/portable/renesas/rusb2/hcd_rusb2.c + ${TOP}/src/portable/renesas/rusb2/dcd_rusb2.c + ${TOP}/src/portable/renesas/rusb2/hcd_rusb2.c + ${TOP}/src/portable/renesas/rusb2/rusb2_ra.c ) target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) diff --git a/hw/bsp/ra/family.mk b/hw/bsp/ra/family.mk index cf8e5d9e9..3394d41b4 100644 --- a/hw/bsp/ra/family.mk +++ b/hw/bsp/ra/family.mk @@ -32,6 +32,7 @@ endif SRC_C += \ src/portable/renesas/rusb2/dcd_rusb2.c \ src/portable/renesas/rusb2/hcd_rusb2.c \ + src/portable/renesas/rusb2/rusb2_ra.c \ $(FSP_RA)/src/bsp/cmsis/Device/RENESAS/Source/startup.c \ $(FSP_RA)/src/bsp/cmsis/Device/RENESAS/Source/system.c \ $(FSP_RA)/src/bsp/mcu/all/bsp_clocks.c \ diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 9a3983f56..3ec1b70b5 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -50,11 +50,6 @@ #define D0FIFOCTR_b CFIFOCTR_b #endif - // Application API for setting IRQ number - void tud_rusb2_set_irqnum(uint8_t rhport, int32_t irqnum) { - rusb2_controller[rhport].irqnum = irqnum; - } - #else #error "Unsupported MCU" #endif diff --git a/src/portable/renesas/rusb2/rusb2_ra.c b/src/portable/renesas/rusb2/rusb2_ra.c new file mode 100644 index 000000000..bbffd712e --- /dev/null +++ b/src/portable/renesas/rusb2/rusb2_ra.c @@ -0,0 +1,16 @@ +#include "tusb_option.h" +#include "device/dcd.h" +#include "rusb2_type.h" +#include "rusb2_ra.h" + +rusb2_controller_t rusb2_controller[] = { + { .reg_base = R_USB_FS0_BASE, .irqnum = USBFS_INT_IRQn }, + #ifdef RUSB2_SUPPORT_HIGHSPEED + { .reg_base = R_USB_HS0_BASE, .irqnum = USBHS_USB_INT_RESUME_IRQn }, + #endif +}; + +// Application API for setting IRQ number +void tud_rusb2_set_irqnum(uint8_t rhport, int32_t irqnum) { + rusb2_controller[rhport].irqnum = irqnum; +} \ No newline at end of file diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 7ff272bbc..4774d2e2c 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -74,14 +74,7 @@ typedef struct { #define rusb2_is_highspeed_reg(_reg) (false) #endif -// USBFS_INT_IRQn and USBHS_USB_INT_RESUME_IRQn are generated by FSP -static rusb2_controller_t rusb2_controller[] = { - { .reg_base = R_USB_FS0_BASE, .irqnum = USBFS_INT_IRQn }, - #ifdef RUSB2_SUPPORT_HIGHSPEED - { .reg_base = R_USB_HS0_BASE, .irqnum = USBHS_USB_INT_RESUME_IRQn }, - #endif -}; - +extern rusb2_controller_t rusb2_controller[]; #define RUSB2_REG(_p) ((rusb2_reg_t*) rusb2_controller[_p].reg_base) //--------------------------------------------------------------------+ -- cgit v1.3.1 From 04f1a34c39e109002c89e464103ebed6128c2903 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 1 Aug 2023 17:03:07 +0700 Subject: add rusb2_common.c for dynami irq --- hw/bsp/ra/family.cmake | 1 + hw/bsp/ra/family.mk | 1 + src/portable/renesas/rusb2/dcd_rusb2.c | 5 --- src/portable/renesas/rusb2/hcd_rusb2.c | 6 --- src/portable/renesas/rusb2/rusb2_common.c | 61 +++++++++++++++++++++++++++++++ src/portable/renesas/rusb2/rusb2_ra.h | 8 +--- src/portable/renesas/rusb2/rusb2_type.h | 1 + 7 files changed, 65 insertions(+), 18 deletions(-) create mode 100644 src/portable/renesas/rusb2/rusb2_common.c (limited to 'src/portable') diff --git a/hw/bsp/ra/family.cmake b/hw/bsp/ra/family.cmake index 307e01da8..11bc7c668 100644 --- a/hw/bsp/ra/family.cmake +++ b/hw/bsp/ra/family.cmake @@ -116,6 +116,7 @@ function(family_configure_example TARGET RTOS) target_sources(${TARGET}-tinyusb PUBLIC ${TOP}/src/portable/renesas/rusb2/dcd_rusb2.c ${TOP}/src/portable/renesas/rusb2/hcd_rusb2.c + ${TOP}/src/portable/renesas/rusb2/rusb2_common.c ) target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) diff --git a/hw/bsp/ra/family.mk b/hw/bsp/ra/family.mk index 901808958..9afb38e06 100644 --- a/hw/bsp/ra/family.mk +++ b/hw/bsp/ra/family.mk @@ -34,6 +34,7 @@ endif SRC_C += \ src/portable/renesas/rusb2/dcd_rusb2.c \ src/portable/renesas/rusb2/hcd_rusb2.c \ + src/portable/renesas/rusb2/rusb2_common.c \ $(FSP_RA)/src/bsp/cmsis/Device/RENESAS/Source/startup.c \ $(FSP_RA)/src/bsp/cmsis/Device/RENESAS/Source/system.c \ $(FSP_RA)/src/bsp/mcu/all/bsp_clocks.c \ diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 9a3983f56..3ec1b70b5 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -50,11 +50,6 @@ #define D0FIFOCTR_b CFIFOCTR_b #endif - // Application API for setting IRQ number - void tud_rusb2_set_irqnum(uint8_t rhport, int32_t irqnum) { - rusb2_controller[rhport].irqnum = irqnum; - } - #else #error "Unsupported MCU" #endif diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 7f49dc8a9..621320095 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -34,14 +34,8 @@ #if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) #include "rusb2_rx.h" - #elif TU_CHECK_MCU(OPT_MCU_RAXXX) #include "rusb2_ra.h" - -// void osal_task_delay(uint32_t msec) { -// R_BSP_SoftwareDelay(msec, BSP_DELAY_UNITS_MILLISECONDS); -// } - #else #error "Unsupported MCU" #endif diff --git a/src/portable/renesas/rusb2/rusb2_common.c b/src/portable/renesas/rusb2/rusb2_common.c new file mode 100644 index 000000000..850060777 --- /dev/null +++ b/src/portable/renesas/rusb2/rusb2_common.c @@ -0,0 +1,61 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "tusb_option.h" + +#if defined(TUP_USBIP_RUSB2) && (CFG_TUH_ENABLED || CFG_TUD_ENABLED) + +#include "rusb2_type.h" + +#if TU_CHECK_MCU(OPT_MCU_RX63X, OPT_MCU_RX65X, OPT_MCU_RX72N) +#include "rusb2_rx.h" + +#elif TU_CHECK_MCU(OPT_MCU_RAXXX) +#include "rusb2_ra.h" + +// USBFS_INT_IRQn and USBHS_USB_INT_RESUME_IRQn are generated by FSP +rusb2_controller_t rusb2_controller[] = { + { .reg_base = R_USB_FS0_BASE, .irqnum = USBFS_INT_IRQn }, + #ifdef RUSB2_SUPPORT_HIGHSPEED + { .reg_base = R_USB_HS0_BASE, .irqnum = USBHS_USB_INT_RESUME_IRQn }, + #endif +}; + +// Application API for setting IRQ number. May throw warnings for missing prototypes. +void tusb_rusb2_set_irqnum(uint8_t rhport, int32_t irqnum) { + rusb2_controller[rhport].irqnum = irqnum; +} + +// void osal_task_delay(uint32_t msec) { +// R_BSP_SoftwareDelay(msec, BSP_DELAY_UNITS_MILLISECONDS); +// } + +#else + #error "Unsupported MCU" +#endif + + +#endif diff --git a/src/portable/renesas/rusb2/rusb2_ra.h b/src/portable/renesas/rusb2/rusb2_ra.h index 7ff272bbc..259d3cbdb 100644 --- a/src/portable/renesas/rusb2/rusb2_ra.h +++ b/src/portable/renesas/rusb2/rusb2_ra.h @@ -74,13 +74,7 @@ typedef struct { #define rusb2_is_highspeed_reg(_reg) (false) #endif -// USBFS_INT_IRQn and USBHS_USB_INT_RESUME_IRQn are generated by FSP -static rusb2_controller_t rusb2_controller[] = { - { .reg_base = R_USB_FS0_BASE, .irqnum = USBFS_INT_IRQn }, - #ifdef RUSB2_SUPPORT_HIGHSPEED - { .reg_base = R_USB_HS0_BASE, .irqnum = USBHS_USB_INT_RESUME_IRQn }, - #endif -}; +extern rusb2_controller_t rusb2_controller[]; #define RUSB2_REG(_p) ((rusb2_reg_t*) rusb2_controller[_p].reg_base) diff --git a/src/portable/renesas/rusb2/rusb2_type.h b/src/portable/renesas/rusb2/rusb2_type.h index 005d7f2be..dd88f66a7 100644 --- a/src/portable/renesas/rusb2/rusb2_type.h +++ b/src/portable/renesas/rusb2/rusb2_type.h @@ -28,6 +28,7 @@ #define _TUSB_RUSB2_TYPE_H_ #include +#include #ifdef __cplusplus extern "C" { -- cgit v1.3.1 From edee46e7941f56f5024bf60d56921cfe10d1f7a5 Mon Sep 17 00:00:00 2001 From: Martino Facchin Date: Tue, 1 Aug 2023 15:21:31 +0200 Subject: renesas: host: remove attach_attempt logic --- src/portable/renesas/rusb2/hcd_rusb2.c | 10 ---------- 1 file changed, 10 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 621320095..f6683529a 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -774,7 +774,6 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { void hcd_int_handler(uint8_t rhport) { rusb2_reg_t* rusb = RUSB2_REG(rhport); - static unsigned char attach_attempt = 0; // TODO remove later unsigned is0 = rusb->INTSTS0; unsigned is1 = rusb->INTSTS1; @@ -789,23 +788,14 @@ void hcd_int_handler(uint8_t rhport) if (is1 & RUSB2_INTSTS1_SACK_Msk) { /* Set DATA1 in advance for the next transfer. */ rusb->DCPCTR_b.SQSET = 1; - attach_attempt = 0; hcd_event_xfer_complete(rusb->DCPMAXP_b.DEVSEL, tu_edpt_addr(0, TUSB_DIR_OUT), 8, XFER_RESULT_SUCCESS, true); } if (is1 & RUSB2_INTSTS1_SIGN_Msk) { hcd_event_xfer_complete(rusb->DCPMAXP_b.DEVSEL, tu_edpt_addr(0, TUSB_DIR_OUT), 8, XFER_RESULT_FAILED, true); - if(attach_attempt > 0) { - rusb->DVSTCTR0_b.UACT = 1; - _hcd.need_reset = true; - rusb->INTENB1 = (rusb->INTENB1 & ~RUSB2_INTSTS1_ATTCH_Msk) | RUSB2_INTSTS1_DTCH_Msk; - hcd_event_device_attach(rhport, true); - } - attach_attempt--; } if (is1 & RUSB2_INTSTS1_ATTCH_Msk) { - attach_attempt = 10; rusb->DVSTCTR0_b.UACT = 1; _hcd.need_reset = true; rusb->INTENB1 = (rusb->INTENB1 & ~RUSB2_INTSTS1_ATTCH_Msk) | RUSB2_INTSTS1_DTCH_Msk; -- cgit v1.3.1 From a160da1f2b941741234f429417798b8df5c33294 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 3 Aug 2023 17:19:47 +0700 Subject: add lpc43 family --- .github/workflows/cmake_arm.yml | 2 +- examples/device/hid_boot_interface/src/main.c | 2 +- examples/typec/power_delivery/src/main.c | 2 +- hw/bsp/board_api.h | 6 +- hw/bsp/ea4357/board.mk | 48 ---- hw/bsp/ea4357/ea4357.c | 301 ---------------------- hw/bsp/ea4357/lpc4357.ld | 324 ------------------------ hw/bsp/ea4357/pca9532.c | 352 -------------------------- hw/bsp/ea4357/pca9532.h | 94 ------- hw/bsp/lpc43/FreeRTOSConfig/FreeRTOSConfig.h | 165 ++++++++++++ hw/bsp/lpc43/boards/ea4357/board.cmake | 16 ++ hw/bsp/lpc43/boards/ea4357/board.h | 40 +++ hw/bsp/lpc43/boards/ea4357/board.mk | 11 + hw/bsp/lpc43/boards/ea4357/lpc4357.ld | 324 ++++++++++++++++++++++++ hw/bsp/lpc43/boards/ea4357/pca9532.c | 352 ++++++++++++++++++++++++++ hw/bsp/lpc43/boards/ea4357/pca9532.h | 94 +++++++ hw/bsp/lpc43/family.c | 312 +++++++++++++++++++++++ hw/bsp/lpc43/family.cmake | 97 +++++++ hw/bsp/lpc43/family.mk | 34 +++ src/portable/chipidea/ci_hs/ci_hs_lpc18_43.h | 9 + 20 files changed, 1462 insertions(+), 1123 deletions(-) delete mode 100644 hw/bsp/ea4357/board.mk delete mode 100644 hw/bsp/ea4357/ea4357.c delete mode 100644 hw/bsp/ea4357/lpc4357.ld delete mode 100644 hw/bsp/ea4357/pca9532.c delete mode 100644 hw/bsp/ea4357/pca9532.h create mode 100644 hw/bsp/lpc43/FreeRTOSConfig/FreeRTOSConfig.h create mode 100644 hw/bsp/lpc43/boards/ea4357/board.cmake create mode 100644 hw/bsp/lpc43/boards/ea4357/board.h create mode 100644 hw/bsp/lpc43/boards/ea4357/board.mk create mode 100644 hw/bsp/lpc43/boards/ea4357/lpc4357.ld create mode 100644 hw/bsp/lpc43/boards/ea4357/pca9532.c create mode 100644 hw/bsp/lpc43/boards/ea4357/pca9532.h create mode 100644 hw/bsp/lpc43/family.c create mode 100644 hw/bsp/lpc43/family.cmake create mode 100644 hw/bsp/lpc43/family.mk (limited to 'src/portable') diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index 276360650..5203337ec 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -35,7 +35,7 @@ jobs: # Alphabetical order - 'imxrt' - 'kinetis_kl' - - 'lpc18 lpc40' + - 'lpc18 lpc40 lpc43' - 'lpc55' - 'mcx' - 'ra' diff --git a/examples/device/hid_boot_interface/src/main.c b/examples/device/hid_boot_interface/src/main.c index 1a155996a..18f301ff0 100644 --- a/examples/device/hid_boot_interface/src/main.c +++ b/examples/device/hid_boot_interface/src/main.c @@ -27,7 +27,7 @@ #include #include -#include "bsp/board.h" +#include "bsp/board_api.h" #include "tusb.h" #include "usb_descriptors.h" diff --git a/examples/typec/power_delivery/src/main.c b/examples/typec/power_delivery/src/main.c index 08590aa74..489d01aa1 100644 --- a/examples/typec/power_delivery/src/main.c +++ b/examples/typec/power_delivery/src/main.c @@ -27,7 +27,7 @@ #include #include -#include "bsp/board.h" +#include "bsp/board_api.h" #include "tusb.h" //--------------------------------------------------------------------+ diff --git a/hw/bsp/board_api.h b/hw/bsp/board_api.h index a7f3826d1..7249f618d 100644 --- a/hw/bsp/board_api.h +++ b/hw/bsp/board_api.h @@ -112,10 +112,14 @@ static inline void board_led_off(void) { static inline void board_delay(uint32_t ms) { uint32_t start_ms = board_millis(); while ( board_millis() - start_ms < ms ) { - #if CFG_TUD_ENABLED // take chance to run usb background + #if CFG_TUD_ENABLED tud_task(); #endif + + #if CFG_TUH_ENABLED + tuh_task(); + #endif } } diff --git a/hw/bsp/ea4357/board.mk b/hw/bsp/ea4357/board.mk deleted file mode 100644 index 6fd229166..000000000 --- a/hw/bsp/ea4357/board.mk +++ /dev/null @@ -1,48 +0,0 @@ -DEPS_SUBMODULES += hw/mcu/nxp/lpcopen - -CFLAGS += \ - -flto \ - -mthumb \ - -mabi=aapcs \ - -mcpu=cortex-m4 \ - -mfloat-abi=hard \ - -mfpu=fpv4-sp-d16 \ - -nostdlib \ - -DCORE_M4 \ - -D__USE_LPCOPEN \ - -DCFG_TUSB_MCU=OPT_MCU_LPC43XX - -# mcu driver cause following warnings -CFLAGS += -Wno-error=unused-parameter -Wno-error=strict-prototypes -Wno-error=cast-qual - -MCU_DIR = hw/mcu/nxp/lpcopen/lpc43xx/lpc_chip_43xx - -# All source paths should be relative to the top level. -LD_FILE = hw/bsp/$(BOARD)/lpc4357.ld - -SRC_C += \ - src/portable/chipidea/ci_hs/dcd_ci_hs.c \ - src/portable/chipidea/ci_hs/hcd_ci_hs.c \ - src/portable/ehci/ehci.c \ - $(MCU_DIR)/../gcc/cr_startup_lpc43xx.c \ - $(MCU_DIR)/src/chip_18xx_43xx.c \ - $(MCU_DIR)/src/clock_18xx_43xx.c \ - $(MCU_DIR)/src/gpio_18xx_43xx.c \ - $(MCU_DIR)/src/sysinit_18xx_43xx.c \ - $(MCU_DIR)/src/i2c_18xx_43xx.c \ - $(MCU_DIR)/src/i2cm_18xx_43xx.c \ - $(MCU_DIR)/src/uart_18xx_43xx.c \ - $(MCU_DIR)/src/fpu_init.c - -INC += \ - $(TOP)/$(MCU_DIR)/inc \ - $(TOP)/$(MCU_DIR)/inc/config_43xx - -# For freeRTOS port source -FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM4F - -# For flash-jlink target -JLINK_DEVICE = LPC4357_M4 - -# flash using jlink -flash: flash-jlink diff --git a/hw/bsp/ea4357/ea4357.c b/hw/bsp/ea4357/ea4357.c deleted file mode 100644 index 06975b8cc..000000000 --- a/hw/bsp/ea4357/ea4357.c +++ /dev/null @@ -1,301 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "chip.h" -#include "../board_api.h" -#include "pca9532.h" - -#define UART_DEV LPC_USART0 -#define UART_PORT 0x0f -#define UART_PIN_TX 10 -#define UART_PIN_RX 11 - -// P9_1 joystick down -#define BUTTON_PORT 4 -#define BUTTON_PIN 13 - -//static const struct { -// uint8_t mux_port; -// uint8_t mux_pin; -// -// uint8_t gpio_port; -// uint8_t gpio_pin; -//}buttons[] = -//{ -// {0x0a, 3, 4, 10 }, // Joystick up -// {0x09, 1, 4, 13 }, // Joystick down -// {0x0a, 2, 4, 9 }, // Joystick left -// {0x09, 0, 4, 12 }, // Joystick right -// {0x0a, 1, 4, 8 }, // Joystick press -// {0x02, 7, 0, 7 }, // SW6 -//}; - -#ifdef BOARD_TUD_RHPORT - #define PORT_SUPPORT_DEVICE(_n) (BOARD_TUD_RHPORT == _n) -#else - #define PORT_SUPPORT_DEVICE(_n) 0 -#endif - -#ifdef BOARD_TUH_RHPORT - #define PORT_SUPPORT_HOST(_n) (BOARD_TUH_RHPORT == _n) -#else - #define PORT_SUPPORT_HOST(_n) 0 -#endif - -/*------------------------------------------------------------------*/ -/* BOARD API - *------------------------------------------------------------------*/ - -/* System configuration variables used by chip driver */ -const uint32_t OscRateIn = 12000000; -const uint32_t ExtRateIn = 0; - -static const PINMUX_GRP_T pinmuxing[] = -{ - // Button ( Joystick down ) - {0x9, 1, (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC0 | SCU_MODE_PULLUP)}, - - // UART - {UART_PORT, UART_PIN_TX, SCU_MODE_PULLDOWN | SCU_MODE_FUNC1}, - {UART_PORT, UART_PIN_RX, SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_FUNC1}, - - // USB -}; - -/* Pin clock mux values, re-used structure, value in first index is meaningless */ -static const PINMUX_GRP_T pinclockmuxing[] = -{ - {0, 0, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)}, - {0, 1, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)}, - {0, 2, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)}, - {0, 3, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)}, -}; - -// Invoked by startup code -void SystemInit(void) -{ -#ifdef __USE_LPCOPEN - extern void (* const g_pfnVectors[])(void); - unsigned int *pSCB_VTOR = (unsigned int *) 0xE000ED08; - *pSCB_VTOR = (unsigned int) g_pfnVectors; - -#if __FPU_USED == 1 - fpuInit(); -#endif -#endif // __USE_LPCOPEN - - /* Setup system level pin muxing */ - Chip_SCU_SetPinMuxing(pinmuxing, sizeof(pinmuxing) / sizeof(PINMUX_GRP_T)); - - /* Clock pins only, group field not used */ - for (int i = 0; i <(int) (sizeof(pinclockmuxing) / sizeof(pinclockmuxing[0])); i++) - { - Chip_SCU_ClockPinMuxSet(pinclockmuxing[i].pinnum, pinclockmuxing[i].modefunc); - } - - Chip_SetupXtalClocking(); -} - -void board_init(void) -{ - SystemCoreClockUpdate(); - -#if CFG_TUSB_OS == OPT_OS_NONE - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); -#elif CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); -#endif - - Chip_GPIO_Init(LPC_GPIO_PORT); - - // LED via pca9532 I2C - Chip_SCU_I2C0PinConfig(I2C0_STANDARD_FAST_MODE); - Chip_I2C_Init(I2C0); - Chip_I2C_SetClockRate(I2C0, 100000); - Chip_I2C_SetMasterEventHandler(I2C0, Chip_I2C_EventHandlerPolling); - - pca9532_init(); - - // Button - Chip_GPIO_SetPinDIRInput(LPC_GPIO_PORT, BUTTON_PORT, BUTTON_PIN); - - //------------- UART -------------// - Chip_UART_Init(UART_DEV); - Chip_UART_SetBaud(UART_DEV, CFG_BOARD_UART_BAUDRATE); - Chip_UART_ConfigData(UART_DEV, UART_LCR_WLEN8 | UART_LCR_SBS_1BIT | UART_LCR_PARITY_DIS); - Chip_UART_TXEnable(UART_DEV); - - //------------- USB -------------// - enum { - USBMODE_DEVICE = 2, - USBMODE_HOST = 3 - }; - - enum { - USBMODE_VBUS_LOW = 0, - USBMODE_VBUS_HIGH = 1 - }; - - /* From EA4357 user manual - * - * USB0 Device operation: - * - Insert jumpers in position 1-2 in JP17/JP18/JP19. - * - GPIO28 controls USB connect functionality - * - LED32 lights when the USB Device is connected. SJ4 has pads 1-2 shorted by default. - * - LED33 is controlled by GPIO27 and signals USB-up state. GPIO54 is used for VBUS - * sensing. - * - * USB0 Host operation: - * - insert jumpers in position 2-3 in JP17/JP18/JP19. - * - USB Host power is controlled via distribution switch U20 (found in schematic page 11). - * - Signal GPIO26 is active low and enables +5V on VBUS2. - * - LED35 light whenever +5V is present on VBUS2. - * - GPIO55 is connected to status feedback from the distribution switch. - * - GPIO54 is used for VBUS sensing. 15Kohm pull-down resistors are always active - * - * Note: - * - Insert jumpers in position 2-3 in JP17/JP18/JP19 - * - Insert jumpers in JP31 (OTG) - */ -#if PORT_SUPPORT_DEVICE(0) || PORT_SUPPORT_HOST(0) - Chip_USB0_Init(); -#endif - - /* From EA4357 user manual - * - * For USB1 Device: - * - a 1.5Kohm pull-up resistor is needed on the USB DP data signal. There are two methods to create this. - * JP15 is inserted and the pull-up resistor is always enabled. Alternatively, the pull-up resistor is activated - * inside the USB OTG chip (U31), and this has to be done via the I2C interface of GPIO52/GPIO53. In the latter case, - * JP15 shall not be inserted. - * - J19 is the connector to use when USB Device is used. Normally it should be a USB-B connector for - * creating a USB Device interface, but the mini-AB connector can also be used in this case. The status - * of VBUS can be read via U31. - * - JP16 shall not be inserted. - * - * For USB1 Host: - * - 15Kohm pull-down resistors are needed on the USB data signals. These are activated inside the USB OTG chip (U31), - * and this has to be done via the I2C interface of GPIO52/GPIO53. - * - J20 is the connector to use when USB Host is used. In order to provide +5V to the external USB - * device connected to this connector (J20), channel A of U20 must be enabled. It is enabled by default - * since SJ5 is normally connected between pin 1-2. - * - LED34 lights green when +5V is available on J20. - * - JP15 shall not be inserted. JP16 has no effect - */ -#if PORT_SUPPORT_DEVICE(1) || PORT_SUPPORT_HOST(1) - Chip_USB1_Init(); -#endif - - // USB0 Vbus Power: P2_3 on EA4357 channel B U20 GPIO26 active low (base board) - Chip_SCU_PinMuxSet(2, 3, SCU_MODE_PULLUP | SCU_MODE_INBUFF_EN | SCU_MODE_FUNC7); - - #if PORT_SUPPORT_DEVICE(0) - // P9_5 (GPIO5[18]) (GPIO28 on oem base) as USB connect, active low. - Chip_SCU_PinMuxSet(9, 5, SCU_MODE_PULLDOWN | SCU_MODE_FUNC4); - Chip_GPIO_SetPinDIROutput(LPC_GPIO_PORT, 5, 18); - #endif - - // USB1 Power: EA4357 channel A U20 is enabled by SJ5 connected to pad 1-2, no more action required - // TODO Remove R170, R171, solder a pair of 15K to USB1 D+/D- to test with USB1 Host -} - -//--------------------------------------------------------------------+ -// USB Interrupt Handler -//--------------------------------------------------------------------+ -void USB0_IRQHandler(void) -{ - #if PORT_SUPPORT_DEVICE(0) - tud_int_handler(0); - #endif - - #if PORT_SUPPORT_HOST(0) - tuh_int_handler(0); - #endif -} - -void USB1_IRQHandler(void) -{ - #if PORT_SUPPORT_DEVICE(1) - tud_int_handler(1); - #endif - - #if PORT_SUPPORT_HOST(1) - tuh_int_handler(1); - #endif -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - if (state) - { - pca9532_setLeds( LED1, 0 ); - }else - { - pca9532_setLeds( 0, LED1); - } -} - -uint32_t board_button_read(void) -{ - // active low - return Chip_GPIO_GetPinState(LPC_GPIO_PORT, BUTTON_PORT, BUTTON_PIN) ? 0 : 1; -} - -int board_uart_read(uint8_t* buf, int len) -{ - return Chip_UART_Read(UART_DEV, buf, len); -} - -int board_uart_write(void const * buf, int len) -{ - uint8_t const* buf8 = (uint8_t const*) buf; - for(int i=0; i MFlashB512 - - /* MAIN TEXT SECTION */ - .text : ALIGN(4) - { - FILL(0xff) - __vectors_start__ = ABSOLUTE(.) ; - KEEP(*(.isr_vector)) - /* Global Section Table */ - . = ALIGN(4) ; - __section_table_start = .; - __data_section_table = .; - LONG(LOADADDR(.data)); - LONG( ADDR(.data)); - LONG( SIZEOF(.data)); - LONG(LOADADDR(.data_RAM2)); - LONG( ADDR(.data_RAM2)); - LONG( SIZEOF(.data_RAM2)); - LONG(LOADADDR(.data_RAM3)); - LONG( ADDR(.data_RAM3)); - LONG( SIZEOF(.data_RAM3)); - LONG(LOADADDR(.data_RAM4)); - LONG( ADDR(.data_RAM4)); - LONG( SIZEOF(.data_RAM4)); - LONG(LOADADDR(.data_RAM5)); - LONG( ADDR(.data_RAM5)); - LONG( SIZEOF(.data_RAM5)); - __data_section_table_end = .; - __bss_section_table = .; - LONG( ADDR(.bss)); - LONG( SIZEOF(.bss)); - LONG( ADDR(.bss_RAM2)); - LONG( SIZEOF(.bss_RAM2)); - LONG( ADDR(.bss_RAM3)); - LONG( SIZEOF(.bss_RAM3)); - LONG( ADDR(.bss_RAM4)); - LONG( SIZEOF(.bss_RAM4)); - LONG( ADDR(.bss_RAM5)); - LONG( SIZEOF(.bss_RAM5)); - __bss_section_table_end = .; - __section_table_end = . ; - /* End of Global Section Table */ - - *(.after_vectors*) - - } > MFlashA512 - - .text : ALIGN(4) - { - *(.text*) - *(.rodata .rodata.* .constdata .constdata.*) - . = ALIGN(4); - } > MFlashA512 - /* - * for exception handling/unwind - some Newlib functions (in common - * with C++ and STDC++) use this. - */ - .ARM.extab : ALIGN(4) - { - *(.ARM.extab* .gnu.linkonce.armextab.*) - } > MFlashA512 - - __exidx_start = .; - - .ARM.exidx : ALIGN(4) - { - *(.ARM.exidx* .gnu.linkonce.armexidx.*) - } > MFlashA512 - __exidx_end = .; - - _etext = .; - - /* DATA section for RamLoc40 */ - - .data_RAM2 : ALIGN(4) - { - FILL(0xff) - PROVIDE(__start_data_RAM2 = .) ; - *(.ramfunc.$RAM2) - *(.ramfunc.$RamLoc40) - *(.data.$RAM2*) - *(.data.$RamLoc40*) - . = ALIGN(4) ; - PROVIDE(__end_data_RAM2 = .) ; - } > RamLoc40 AT>MFlashA512 - /* DATA section for RamAHB32 */ - - .data_RAM3 : ALIGN(4) - { - FILL(0xff) - PROVIDE(__start_data_RAM3 = .) ; - *(.ramfunc.$RAM3) - *(.ramfunc.$RamAHB32) - *(.data.$RAM3*) - *(.data.$RamAHB32*) - . = ALIGN(4) ; - PROVIDE(__end_data_RAM3 = .) ; - } > RamAHB32 AT>MFlashA512 - /* DATA section for RamAHB16 */ - - .data_RAM4 : ALIGN(4) - { - FILL(0xff) - PROVIDE(__start_data_RAM4 = .) ; - *(.ramfunc.$RAM4) - *(.ramfunc.$RamAHB16) - *(.data.$RAM4*) - *(.data.$RamAHB16*) - . = ALIGN(4) ; - PROVIDE(__end_data_RAM4 = .) ; - } > RamAHB16 AT>MFlashA512 - /* DATA section for RamAHB_ETB16 */ - - .data_RAM5 : ALIGN(4) - { - FILL(0xff) - PROVIDE(__start_data_RAM5 = .) ; - *(.ramfunc.$RAM5) - *(.ramfunc.$RamAHB_ETB16) - *(.data.$RAM5*) - *(.data.$RamAHB_ETB16*) - . = ALIGN(4) ; - PROVIDE(__end_data_RAM5 = .) ; - } > RamAHB_ETB16 AT>MFlashA512 - /* MAIN DATA SECTION */ - .uninit_RESERVED : ALIGN(4) - { - KEEP(*(.bss.$RESERVED*)) - . = ALIGN(4) ; - _end_uninit_RESERVED = .; - } > RamLoc32 - - /* Main DATA section (RamLoc32) */ - .data : ALIGN(4) - { - FILL(0xff) - _data = . ; - *(vtable) - *(.ramfunc*) - *(.data*) - . = ALIGN(4) ; - _edata = . ; - } > RamLoc32 AT>MFlashA512 - - /* BSS section for RamLoc40 */ - .bss_RAM2 : ALIGN(4) - { - PROVIDE(__start_bss_RAM2 = .) ; - *(.bss.$RAM2*) - *(.bss.$RamLoc40*) - . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ - PROVIDE(__end_bss_RAM2 = .) ; - } > RamLoc40 - - /* BSS section for RamAHB32 */ - .bss_RAM3 : ALIGN(4) - { - PROVIDE(__start_bss_RAM3 = .) ; - *(.bss.$RAM3*) - *(.bss.$RamAHB32*) - . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ - PROVIDE(__end_bss_RAM3 = .) ; - } > RamAHB32 - - /* BSS section for RamAHB16 */ - .bss_RAM4 : ALIGN(4) - { - PROVIDE(__start_bss_RAM4 = .) ; - *(.bss.$RAM4*) - *(.bss.$RamAHB16*) - . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ - PROVIDE(__end_bss_RAM4 = .) ; - } > RamAHB16 - - /* BSS section for RamAHB_ETB16 */ - .bss_RAM5 : ALIGN(4) - { - PROVIDE(__start_bss_RAM5 = .) ; - *(.bss.$RAM5*) - *(.bss.$RamAHB_ETB16*) - . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ - PROVIDE(__end_bss_RAM5 = .) ; - } > RamAHB_ETB16 - - /* MAIN BSS SECTION */ - .bss : ALIGN(4) - { - _bss = .; - *(.bss*) - *(COMMON) - . = ALIGN(4) ; - _ebss = .; - PROVIDE(end = .); - } > RamLoc32 - - /* NOINIT section for RamLoc40 */ - .noinit_RAM2 (NOLOAD) : ALIGN(4) - { - *(.noinit.$RAM2*) - *(.noinit.$RamLoc40*) - . = ALIGN(4) ; - } > RamLoc40 - - /* NOINIT section for RamAHB32 */ - .noinit_RAM3 (NOLOAD) : ALIGN(4) - { - *(.noinit.$RAM3*) - *(.noinit.$RamAHB32*) - . = ALIGN(4) ; - } > RamAHB32 - - /* NOINIT section for RamAHB16 */ - .noinit_RAM4 (NOLOAD) : ALIGN(4) - { - *(.noinit.$RAM4*) - *(.noinit.$RamAHB16*) - . = ALIGN(4) ; - } > RamAHB16 - - /* NOINIT section for RamAHB_ETB16 */ - .noinit_RAM5 (NOLOAD) : ALIGN(4) - { - *(.noinit.$RAM5*) - *(.noinit.$RamAHB_ETB16*) - . = ALIGN(4) ; - } > RamAHB_ETB16 - - /* DEFAULT NOINIT SECTION */ - .noinit (NOLOAD): ALIGN(4) - { - _noinit = .; - *(.noinit*) - . = ALIGN(4) ; - _end_noinit = .; - } > RamLoc32 - PROVIDE(_pvHeapStart = DEFINED(__user_heap_base) ? __user_heap_base : .); - PROVIDE(_vStackTop = DEFINED(__user_stack_top) ? __user_stack_top : __top_RamLoc32 - 0); - - /* ## Create checksum value (used in startup) ## */ - PROVIDE(__valid_user_code_checksum = 0 - - (_vStackTop - + (ResetISR + 1) - + (NMI_Handler + 1) - + (HardFault_Handler + 1) - + (( DEFINED(MemManage_Handler) ? MemManage_Handler : 0 ) + 1) /* MemManage_Handler may not be defined */ - + (( DEFINED(BusFault_Handler) ? BusFault_Handler : 0 ) + 1) /* BusFault_Handler may not be defined */ - + (( DEFINED(UsageFault_Handler) ? UsageFault_Handler : 0 ) + 1) /* UsageFault_Handler may not be defined */ - ) ); - - /* Provide basic symbols giving location and size of main text - * block, including initial values of RW data sections. Note that - * these will need extending to give a complete picture with - * complex images (e.g multiple Flash banks). - */ - _image_start = LOADADDR(.text); - _image_end = LOADADDR(.data) + SIZEOF(.data); - _image_size = _image_end - _image_start; -} diff --git a/hw/bsp/ea4357/pca9532.c b/hw/bsp/ea4357/pca9532.c deleted file mode 100644 index 150167cde..000000000 --- a/hw/bsp/ea4357/pca9532.c +++ /dev/null @@ -1,352 +0,0 @@ -/***************************************************************************** - * - * Copyright(C) 2011, Embedded Artists AB - * All rights reserved. - * - ****************************************************************************** - * Software that is described herein is for illustrative purposes only - * which provides customers with programming information regarding the - * products. This software is supplied "AS IS" without any warranties. - * Embedded Artists AB assumes no responsibility or liability for the - * use of the software, conveys no license or title under any patent, - * copyright, or mask work right to the product. Embedded Artists AB - * reserves the right to make changes in the software without - * notification. Embedded Artists AB also make no representation or - * warranty that such application will be suitable for the specified - * use without further testing or modification. - *****************************************************************************/ - -/* - * NOTE: I2C must have been initialized before calling any functions in this - * file. - */ - -/****************************************************************************** - * Includes - *****************************************************************************/ - -//#include "board.h" -#include "chip.h" - -#include "pca9532.h" - -/****************************************************************************** - * Defines and typedefs - *****************************************************************************/ - -#define I2C_PORT (LPC_I2C0) - -#define LS_MODE_ON 0x01 -#define LS_MODE_BLINK0 0x02 -#define LS_MODE_BLINK1 0x03 - -/****************************************************************************** - * External global variables - *****************************************************************************/ - - -/****************************************************************************** - * Local variables - *****************************************************************************/ - -static uint16_t blink0Shadow = 0; -static uint16_t blink1Shadow = 0; -static uint16_t ledStateShadow = 0; - -/****************************************************************************** - * Local Functions - *****************************************************************************/ - -static Status I2CWrite(uint32_t addr, uint8_t* buf, uint32_t len) -{ - I2CM_XFER_T i2cData; - - i2cData.slaveAddr = addr; - i2cData.options = 0; - i2cData.status = 0; - i2cData.txBuff = buf; - i2cData.txSz = len; - i2cData.rxBuff = NULL; - i2cData.rxSz = 0; - - if (Chip_I2CM_XferBlocking(LPC_I2C0, &i2cData) == 0) { - return ERROR; - } - return SUCCESS; -} - -static Status I2CRead(uint32_t addr, uint8_t* buf, uint32_t len) -{ - I2CM_XFER_T i2cData; - - i2cData.slaveAddr = addr; - i2cData.options = 0; - i2cData.status = 0; - i2cData.txBuff = NULL; - i2cData.txSz = 0; - i2cData.rxBuff = buf; - i2cData.rxSz = len; - - if (Chip_I2CM_XferBlocking(LPC_I2C0, &i2cData) == 0) { - return ERROR; - } - return SUCCESS; -} - -static void setLsStates(uint16_t states, uint8_t* ls, uint8_t mode) -{ -#define IS_LED_SET(bit, x) ( ( ((x) & (bit)) != 0 ) ? 1 : 0 ) - - int i = 0; - - for (i = 0; i < 4; i++) { - - ls[i] |= ( (IS_LED_SET(0x0001, states)*mode << 0) - | (IS_LED_SET(0x0002, states)*mode << 2) - | (IS_LED_SET(0x0004, states)*mode << 4) - | (IS_LED_SET(0x0008, states)*mode << 6) ); - - states >>= 4; - } -} - -static void setLeds(void) -{ - uint8_t buf[5]; - uint8_t ls[4] = {0,0,0,0}; - uint16_t states = ledStateShadow; - - /* LEDs in On/Off state */ - setLsStates(states, ls, LS_MODE_ON); - - /* set the LEDs that should blink */ - setLsStates(blink0Shadow, ls, LS_MODE_BLINK0); - setLsStates(blink1Shadow, ls, LS_MODE_BLINK1); - - - buf[0] = PCA9532_LS0 | PCA9532_AUTO_INC; - buf[1] = ls[0]; - buf[2] = ls[1]; - buf[3] = ls[2]; - buf[4] = ls[3]; - I2CWrite(PCA9532_I2C_ADDR, buf, 5); -} - -/****************************************************************************** - * Public Functions - *****************************************************************************/ - -/****************************************************************************** - * - * Description: - * Initialize the PCA9532 Device - * - *****************************************************************************/ -void pca9532_init (void) -{ - /* nothing to initialize */ -} - -/****************************************************************************** - * - * Description: - * Get the LED states - * - * Params: - * [in] shadow - TRUE if the states should be retrieved from the shadow - * variables. The shadow variable are updated when any - * of setLeds, setBlink0Leds and/or setBlink1Leds are - * called. - * - * FALSE if the state should be retrieved from the PCA9532 - * device. A blinkin LED may be reported as on or off - * depending on the state when calling the function. - * - * Returns: - * A mask where a 1 indicates that a LED is on (or blinking). - * - *****************************************************************************/ -uint16_t pca9532_getLedState (uint32_t shadow) -{ - uint8_t buf[2]; - uint16_t ret = 0; - - if (shadow) { - /* a blink LED is reported as on*/ - ret = (ledStateShadow | blink0Shadow | blink1Shadow); - } - else { - - /* - * A blinking LED may be reported as on or off depending on - * its state when reading the Input register. - */ - - buf[0] = PCA9532_INPUT0; - I2CWrite(PCA9532_I2C_ADDR, buf, 1); - - I2CRead(PCA9532_I2C_ADDR, buf, 1); - ret = buf[0]; - - - buf[0] = PCA9532_INPUT1; - I2CWrite(PCA9532_I2C_ADDR, buf, 1); - - I2CRead(PCA9532_I2C_ADDR, buf, 1); - ret |= (buf[0] << 8); - - - /* invert since LEDs are active low */ - ret = ((~ret) & 0xFFFF); - } - - return (ret & ~PCA9532_NOT_USED); -} - - -/****************************************************************************** - * - * Description: - * Set LED states (on or off). - * - * Params: - * [in] ledOnMask - The LEDs that should be turned on. This mask has - * priority over ledOffMask - * [in] ledOffMask - The LEDs that should be turned off. - * - *****************************************************************************/ -void pca9532_setLeds (uint16_t ledOnMask, uint16_t ledOffMask) -{ - /* turn off leds */ - ledStateShadow &= (~(ledOffMask) & 0xffff); - - /* ledOnMask has priority over ledOffMask */ - ledStateShadow |= ledOnMask; - - /* turn off blinking */ - blink0Shadow &= (~(ledOffMask) & 0xffff); - blink1Shadow &= (~(ledOffMask) & 0xffff); - - setLeds(); -} - -/****************************************************************************** - * - * Description: - * Set the blink period for PWM0. Valid values are 0 - 255 where 0 - * means 152 Hz and 255 means 0.59 Hz. A value of 151 means 1 Hz. - * - * Params: - * [in] period - the period for pwm0 - * - *****************************************************************************/ -void pca9532_setBlink0Period(uint8_t period) -{ - uint8_t buf[2]; - - buf[0] = PCA9532_PSC0; - buf[1] = period; - I2CWrite(PCA9532_I2C_ADDR, buf, 2); -} - -/****************************************************************************** - * - * Description: - * Set the duty cycle for PWM0. Valid values are 0 - 100. 25 means the LED - * is on 25% of the period. - * - * Params: - * [in] duty - duty cycle - * - *****************************************************************************/ -void pca9532_setBlink0Duty(uint8_t duty) -{ - uint8_t buf[2]; - uint32_t tmp = duty; - if (tmp > 100) { - tmp = 100; - } - - tmp = (256 * tmp)/100; - - buf[0] = PCA9532_PWM0; - buf[1] = tmp; - I2CWrite(PCA9532_I2C_ADDR, buf, 2); -} - -/****************************************************************************** - * - * Description: - * Set the LEDs that should blink with rate and duty cycle from PWM0. - * Blinking is turned off with pca9532_setLeds. - * - * Params: - * [in] ledMask - LEDs that should blink. - * - *****************************************************************************/ -void pca9532_setBlink0Leds(uint16_t ledMask) -{ - blink0Shadow |= ledMask; - setLeds(); -} - -/****************************************************************************** - * - * Description: - * Set the blink period for PWM1. Valid values are 0 - 255 where 0 - * means 152 Hz and 255 means 0.59 Hz. A value of 151 means 1 Hz. - * - * Params: - * [in] period - The period for PWM1 - * - *****************************************************************************/ -void pca9532_setBlink1Period(uint8_t period) -{ - uint8_t buf[2]; - - buf[0] = PCA9532_PSC1; - buf[1] = period; - I2CWrite(PCA9532_I2C_ADDR, buf, 2); -} - -/****************************************************************************** - * - * Description: - * Set the duty cycle for PWM1. Valid values are 0 - 100. 25 means the LED - * is on 25% of the period. - * - * Params: - * [in] duty - duty cycle. - * - *****************************************************************************/ -void pca9532_setBlink1Duty(uint8_t duty) -{ - uint8_t buf[2]; - - uint32_t tmp = duty; - if (tmp > 100) { - tmp = 100; - } - - tmp = (256 * tmp)/100; - - buf[0] = PCA9532_PWM1; - buf[1] = tmp; - I2CWrite(PCA9532_I2C_ADDR, buf, 2); -} - -/****************************************************************************** - * - * Description: - * Set the LEDs that should blink with rate and duty cycle from PWM1. - * Blinking is turned off with pca9532_setLeds. - * - * Params: - * [in] ledMask - LEDs that should blink. - * - *****************************************************************************/ -void pca9532_setBlink1Leds(uint16_t ledMask) -{ - blink1Shadow |= ledMask; - setLeds(); -} diff --git a/hw/bsp/ea4357/pca9532.h b/hw/bsp/ea4357/pca9532.h deleted file mode 100644 index f21c1ff09..000000000 --- a/hw/bsp/ea4357/pca9532.h +++ /dev/null @@ -1,94 +0,0 @@ -/***************************************************************************** - * - * Copyright(C) 2011, Embedded Artists AB - * All rights reserved. - * - ****************************************************************************** - * Software that is described herein is for illustrative purposes only - * which provides customers with programming information regarding the - * products. This software is supplied "AS IS" without any warranties. - * Embedded Artists AB assumes no responsibility or liability for the - * use of the software, conveys no license or title under any patent, - * copyright, or mask work right to the product. Embedded Artists AB - * reserves the right to make changes in the software without - * notification. Embedded Artists AB also make no representation or - * warranty that such application will be suitable for the specified - * use without further testing or modification. - *****************************************************************************/ -#ifndef __PCA9532C_H -#define __PCA9532C_H - - -#define PCA9532_I2C_ADDR (0xC0>>1) - -#define PCA9532_INPUT0 0x00 -#define PCA9532_INPUT1 0x01 -#define PCA9532_PSC0 0x02 -#define PCA9532_PWM0 0x03 -#define PCA9532_PSC1 0x04 -#define PCA9532_PWM1 0x05 -#define PCA9532_LS0 0x06 -#define PCA9532_LS1 0x07 -#define PCA9532_LS2 0x08 -#define PCA9532_LS3 0x09 - -#define PCA9532_AUTO_INC 0x10 - - -/* - * The Keys on the base board are mapped to LED0 -> LED3 on - * the PCA9532. - */ - -#define KEY1 0x0001 -#define KEY2 0x0002 -#define KEY3 0x0004 -#define KEY4 0x0008 - -#define KEY_MASK 0x000F - -/* - * MMC Card Detect and MMC Write Protect are mapped to LED4 - * and LED5 on the PCA9532. Please note that WP is active low. - */ - -#define MMC_CD 0x0010 -#define MMC_WP 0x0020 - -#define MMC_MASK 0x30 - -/* NOTE: LED6 and LED7 on PCA9532 are not connected to anything */ -#define PCA9532_NOT_USED 0xC0 - -/* - * Below are the LED constants to use when enabling/disabling a LED. - * The LED names are the names printed on the base board and not - * the names from the PCA9532 device. base_LED1 -> LED8 on PCA9532, - * base_LED2 -> LED9, and so on. - */ - -#define LED1 0x0100 -#define LED2 0x0200 -#define LED3 0x0400 -#define LED4 0x0800 -#define LED5 0x1000 -#define LED6 0x2000 -#define LED7 0x4000 -#define LED8 0x8000 - -#define LED_MASK 0xFF00 - -void pca9532_init (void); -uint16_t pca9532_getLedState (uint32_t shadow); -void pca9532_setLeds (uint16_t ledOnMask, uint16_t ledOffMask); -void pca9532_setBlink0Period(uint8_t period); -void pca9532_setBlink0Duty(uint8_t duty); -void pca9532_setBlink0Leds(uint16_t ledMask); -void pca9532_setBlink1Period(uint8_t period); -void pca9532_setBlink1Duty(uint8_t duty); -void pca9532_setBlink1Leds(uint16_t ledMask); - -#endif /* end __PCA9532C_H */ -/**************************************************************************** -** End Of File -*****************************************************************************/ diff --git a/hw/bsp/lpc43/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/lpc43/FreeRTOSConfig/FreeRTOSConfig.h new file mode 100644 index 000000000..6f80413c0 --- /dev/null +++ b/hw/bsp/lpc43/FreeRTOSConfig/FreeRTOSConfig.h @@ -0,0 +1,165 @@ +/* + * FreeRTOS Kernel V10.0.0 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. If you wish to use our Amazon + * FreeRTOS name, please do so in a fair use way that does not cause confusion. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + + +#ifndef FREERTOS_CONFIG_H +#define FREERTOS_CONFIG_H + +/*----------------------------------------------------------- + * Application specific definitions. + * + * These definitions should be adjusted for your particular hardware and + * application requirements. + * + * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE + * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. + * + * See http://www.freertos.org/a00110.html. + *----------------------------------------------------------*/ + +// skip if included from IAR assembler +#ifndef __IASMARM__ + #include "chip.h" +#endif + +/* Cortex M23/M33 port configuration. */ +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) + +#define configUSE_PREEMPTION 1 +#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 +#define configCPU_CLOCK_HZ SystemCoreClock +#define configTICK_RATE_HZ ( 1000 ) +#define configMAX_PRIORITIES ( 5 ) +#define configMINIMAL_STACK_SIZE ( 128 ) +#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) +#define configMAX_TASK_NAME_LEN 16 +#define configUSE_16_BIT_TICKS 0 +#define configIDLE_SHOULD_YIELD 1 +#define configUSE_MUTEXES 1 +#define configUSE_RECURSIVE_MUTEXES 1 +#define configUSE_COUNTING_SEMAPHORES 1 +#define configQUEUE_REGISTRY_SIZE 4 +#define configUSE_QUEUE_SETS 0 +#define configUSE_TIME_SLICING 0 +#define configUSE_NEWLIB_REENTRANT 0 +#define configENABLE_BACKWARD_COMPATIBILITY 1 +#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 + +#define configSUPPORT_STATIC_ALLOCATION 0 +#define configSUPPORT_DYNAMIC_ALLOCATION 1 + +/* Hook function related definitions. */ +#define configUSE_IDLE_HOOK 0 +#define configUSE_TICK_HOOK 0 +#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning +#define configCHECK_FOR_STACK_OVERFLOW 2 + +/* Run time and task stats gathering related definitions. */ +#define configGENERATE_RUN_TIME_STATS 0 +#define configRECORD_STACK_HIGH_ADDRESS 1 +#define configUSE_TRACE_FACILITY 1 // legacy trace +#define configUSE_STATS_FORMATTING_FUNCTIONS 0 + +/* Co-routine definitions. */ +#define configUSE_CO_ROUTINES 0 +#define configMAX_CO_ROUTINE_PRIORITIES 2 + +/* Software timer related definitions. */ +#define configUSE_TIMERS 1 +#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) +#define configTIMER_QUEUE_LENGTH 32 +#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE + +/* Optional functions - most linkers will remove unused functions anyway. */ +#define INCLUDE_vTaskPrioritySet 0 +#define INCLUDE_uxTaskPriorityGet 0 +#define INCLUDE_vTaskDelete 0 +#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY +#define INCLUDE_xResumeFromISR 0 +#define INCLUDE_vTaskDelayUntil 1 +#define INCLUDE_vTaskDelay 1 +#define INCLUDE_xTaskGetSchedulerState 0 +#define INCLUDE_xTaskGetCurrentTaskHandle 1 +#define INCLUDE_uxTaskGetStackHighWaterMark 0 +#define INCLUDE_xTaskGetIdleTaskHandle 0 +#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 +#define INCLUDE_pcTaskGetTaskName 0 +#define INCLUDE_eTaskGetState 0 +#define INCLUDE_xEventGroupSetBitFromISR 0 +#define INCLUDE_xTimerPendFunctionCall 0 + +/* Define to trap errors during development. */ +// Halt CPU (breakpoint) when hitting error, only apply for Cortex M3, M4, M7 +#if defined(__ARM_ARCH_7M__) || defined (__ARM_ARCH_7EM__) + #define configASSERT(_exp) \ + do {\ + if ( !(_exp) ) { \ + volatile uint32_t* ARM_CM_DHCSR = ((volatile uint32_t*) 0xE000EDF0UL); /* Cortex M CoreDebug->DHCSR */ \ + if ( (*ARM_CM_DHCSR) & 1UL ) { /* Only halt mcu if debugger is attached */ \ + taskDISABLE_INTERRUPTS(); \ + __asm("BKPT #0\n"); \ + }\ + }\ + } while(0) +#else + #define configASSERT( x ) +#endif + +/* FreeRTOS hooks to NVIC vectors */ +#define xPortPendSVHandler PendSV_Handler +#define xPortSysTickHandler SysTick_Handler +#define vPortSVCHandler SVC_Handler + +//--------------------------------------------------------------------+ +// Interrupt nesting behavior configuration. +//--------------------------------------------------------------------+ + +// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header +#define configPRIO_BITS 3 + +/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1< MFlashB512 + + /* MAIN TEXT SECTION */ + .text : ALIGN(4) + { + FILL(0xff) + __vectors_start__ = ABSOLUTE(.) ; + KEEP(*(.isr_vector)) + /* Global Section Table */ + . = ALIGN(4) ; + __section_table_start = .; + __data_section_table = .; + LONG(LOADADDR(.data)); + LONG( ADDR(.data)); + LONG( SIZEOF(.data)); + LONG(LOADADDR(.data_RAM2)); + LONG( ADDR(.data_RAM2)); + LONG( SIZEOF(.data_RAM2)); + LONG(LOADADDR(.data_RAM3)); + LONG( ADDR(.data_RAM3)); + LONG( SIZEOF(.data_RAM3)); + LONG(LOADADDR(.data_RAM4)); + LONG( ADDR(.data_RAM4)); + LONG( SIZEOF(.data_RAM4)); + LONG(LOADADDR(.data_RAM5)); + LONG( ADDR(.data_RAM5)); + LONG( SIZEOF(.data_RAM5)); + __data_section_table_end = .; + __bss_section_table = .; + LONG( ADDR(.bss)); + LONG( SIZEOF(.bss)); + LONG( ADDR(.bss_RAM2)); + LONG( SIZEOF(.bss_RAM2)); + LONG( ADDR(.bss_RAM3)); + LONG( SIZEOF(.bss_RAM3)); + LONG( ADDR(.bss_RAM4)); + LONG( SIZEOF(.bss_RAM4)); + LONG( ADDR(.bss_RAM5)); + LONG( SIZEOF(.bss_RAM5)); + __bss_section_table_end = .; + __section_table_end = . ; + /* End of Global Section Table */ + + *(.after_vectors*) + + } > MFlashA512 + + .text : ALIGN(4) + { + *(.text*) + *(.rodata .rodata.* .constdata .constdata.*) + . = ALIGN(4); + } > MFlashA512 + /* + * for exception handling/unwind - some Newlib functions (in common + * with C++ and STDC++) use this. + */ + .ARM.extab : ALIGN(4) + { + *(.ARM.extab* .gnu.linkonce.armextab.*) + } > MFlashA512 + + __exidx_start = .; + + .ARM.exidx : ALIGN(4) + { + *(.ARM.exidx* .gnu.linkonce.armexidx.*) + } > MFlashA512 + __exidx_end = .; + + _etext = .; + + /* DATA section for RamLoc40 */ + + .data_RAM2 : ALIGN(4) + { + FILL(0xff) + PROVIDE(__start_data_RAM2 = .) ; + *(.ramfunc.$RAM2) + *(.ramfunc.$RamLoc40) + *(.data.$RAM2*) + *(.data.$RamLoc40*) + . = ALIGN(4) ; + PROVIDE(__end_data_RAM2 = .) ; + } > RamLoc40 AT>MFlashA512 + /* DATA section for RamAHB32 */ + + .data_RAM3 : ALIGN(4) + { + FILL(0xff) + PROVIDE(__start_data_RAM3 = .) ; + *(.ramfunc.$RAM3) + *(.ramfunc.$RamAHB32) + *(.data.$RAM3*) + *(.data.$RamAHB32*) + . = ALIGN(4) ; + PROVIDE(__end_data_RAM3 = .) ; + } > RamAHB32 AT>MFlashA512 + /* DATA section for RamAHB16 */ + + .data_RAM4 : ALIGN(4) + { + FILL(0xff) + PROVIDE(__start_data_RAM4 = .) ; + *(.ramfunc.$RAM4) + *(.ramfunc.$RamAHB16) + *(.data.$RAM4*) + *(.data.$RamAHB16*) + . = ALIGN(4) ; + PROVIDE(__end_data_RAM4 = .) ; + } > RamAHB16 AT>MFlashA512 + /* DATA section for RamAHB_ETB16 */ + + .data_RAM5 : ALIGN(4) + { + FILL(0xff) + PROVIDE(__start_data_RAM5 = .) ; + *(.ramfunc.$RAM5) + *(.ramfunc.$RamAHB_ETB16) + *(.data.$RAM5*) + *(.data.$RamAHB_ETB16*) + . = ALIGN(4) ; + PROVIDE(__end_data_RAM5 = .) ; + } > RamAHB_ETB16 AT>MFlashA512 + /* MAIN DATA SECTION */ + .uninit_RESERVED : ALIGN(4) + { + KEEP(*(.bss.$RESERVED*)) + . = ALIGN(4) ; + _end_uninit_RESERVED = .; + } > RamLoc32 + + /* Main DATA section (RamLoc32) */ + .data : ALIGN(4) + { + FILL(0xff) + _data = . ; + *(vtable) + *(.ramfunc*) + *(.data*) + . = ALIGN(4) ; + _edata = . ; + } > RamLoc32 AT>MFlashA512 + + /* BSS section for RamLoc40 */ + .bss_RAM2 : ALIGN(4) + { + PROVIDE(__start_bss_RAM2 = .) ; + *(.bss.$RAM2*) + *(.bss.$RamLoc40*) + . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ + PROVIDE(__end_bss_RAM2 = .) ; + } > RamLoc40 + + /* BSS section for RamAHB32 */ + .bss_RAM3 : ALIGN(4) + { + PROVIDE(__start_bss_RAM3 = .) ; + *(.bss.$RAM3*) + *(.bss.$RamAHB32*) + . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ + PROVIDE(__end_bss_RAM3 = .) ; + } > RamAHB32 + + /* BSS section for RamAHB16 */ + .bss_RAM4 : ALIGN(4) + { + PROVIDE(__start_bss_RAM4 = .) ; + *(.bss.$RAM4*) + *(.bss.$RamAHB16*) + . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ + PROVIDE(__end_bss_RAM4 = .) ; + } > RamAHB16 + + /* BSS section for RamAHB_ETB16 */ + .bss_RAM5 : ALIGN(4) + { + PROVIDE(__start_bss_RAM5 = .) ; + *(.bss.$RAM5*) + *(.bss.$RamAHB_ETB16*) + . = ALIGN (. != 0 ? 4 : 1) ; /* avoid empty segment */ + PROVIDE(__end_bss_RAM5 = .) ; + } > RamAHB_ETB16 + + /* MAIN BSS SECTION */ + .bss : ALIGN(4) + { + _bss = .; + *(.bss*) + *(COMMON) + . = ALIGN(4) ; + _ebss = .; + PROVIDE(end = .); + } > RamLoc32 + + /* NOINIT section for RamLoc40 */ + .noinit_RAM2 (NOLOAD) : ALIGN(4) + { + *(.noinit.$RAM2*) + *(.noinit.$RamLoc40*) + . = ALIGN(4) ; + } > RamLoc40 + + /* NOINIT section for RamAHB32 */ + .noinit_RAM3 (NOLOAD) : ALIGN(4) + { + *(.noinit.$RAM3*) + *(.noinit.$RamAHB32*) + . = ALIGN(4) ; + } > RamAHB32 + + /* NOINIT section for RamAHB16 */ + .noinit_RAM4 (NOLOAD) : ALIGN(4) + { + *(.noinit.$RAM4*) + *(.noinit.$RamAHB16*) + . = ALIGN(4) ; + } > RamAHB16 + + /* NOINIT section for RamAHB_ETB16 */ + .noinit_RAM5 (NOLOAD) : ALIGN(4) + { + *(.noinit.$RAM5*) + *(.noinit.$RamAHB_ETB16*) + . = ALIGN(4) ; + } > RamAHB_ETB16 + + /* DEFAULT NOINIT SECTION */ + .noinit (NOLOAD): ALIGN(4) + { + _noinit = .; + *(.noinit*) + . = ALIGN(4) ; + _end_noinit = .; + } > RamLoc32 + PROVIDE(_pvHeapStart = DEFINED(__user_heap_base) ? __user_heap_base : .); + PROVIDE(_vStackTop = DEFINED(__user_stack_top) ? __user_stack_top : __top_RamLoc32 - 0); + + /* ## Create checksum value (used in startup) ## */ + PROVIDE(__valid_user_code_checksum = 0 - + (_vStackTop + + (ResetISR + 1) + + (NMI_Handler + 1) + + (HardFault_Handler + 1) + + (( DEFINED(MemManage_Handler) ? MemManage_Handler : 0 ) + 1) /* MemManage_Handler may not be defined */ + + (( DEFINED(BusFault_Handler) ? BusFault_Handler : 0 ) + 1) /* BusFault_Handler may not be defined */ + + (( DEFINED(UsageFault_Handler) ? UsageFault_Handler : 0 ) + 1) /* UsageFault_Handler may not be defined */ + ) ); + + /* Provide basic symbols giving location and size of main text + * block, including initial values of RW data sections. Note that + * these will need extending to give a complete picture with + * complex images (e.g multiple Flash banks). + */ + _image_start = LOADADDR(.text); + _image_end = LOADADDR(.data) + SIZEOF(.data); + _image_size = _image_end - _image_start; +} diff --git a/hw/bsp/lpc43/boards/ea4357/pca9532.c b/hw/bsp/lpc43/boards/ea4357/pca9532.c new file mode 100644 index 000000000..150167cde --- /dev/null +++ b/hw/bsp/lpc43/boards/ea4357/pca9532.c @@ -0,0 +1,352 @@ +/***************************************************************************** + * + * Copyright(C) 2011, Embedded Artists AB + * All rights reserved. + * + ****************************************************************************** + * Software that is described herein is for illustrative purposes only + * which provides customers with programming information regarding the + * products. This software is supplied "AS IS" without any warranties. + * Embedded Artists AB assumes no responsibility or liability for the + * use of the software, conveys no license or title under any patent, + * copyright, or mask work right to the product. Embedded Artists AB + * reserves the right to make changes in the software without + * notification. Embedded Artists AB also make no representation or + * warranty that such application will be suitable for the specified + * use without further testing or modification. + *****************************************************************************/ + +/* + * NOTE: I2C must have been initialized before calling any functions in this + * file. + */ + +/****************************************************************************** + * Includes + *****************************************************************************/ + +//#include "board.h" +#include "chip.h" + +#include "pca9532.h" + +/****************************************************************************** + * Defines and typedefs + *****************************************************************************/ + +#define I2C_PORT (LPC_I2C0) + +#define LS_MODE_ON 0x01 +#define LS_MODE_BLINK0 0x02 +#define LS_MODE_BLINK1 0x03 + +/****************************************************************************** + * External global variables + *****************************************************************************/ + + +/****************************************************************************** + * Local variables + *****************************************************************************/ + +static uint16_t blink0Shadow = 0; +static uint16_t blink1Shadow = 0; +static uint16_t ledStateShadow = 0; + +/****************************************************************************** + * Local Functions + *****************************************************************************/ + +static Status I2CWrite(uint32_t addr, uint8_t* buf, uint32_t len) +{ + I2CM_XFER_T i2cData; + + i2cData.slaveAddr = addr; + i2cData.options = 0; + i2cData.status = 0; + i2cData.txBuff = buf; + i2cData.txSz = len; + i2cData.rxBuff = NULL; + i2cData.rxSz = 0; + + if (Chip_I2CM_XferBlocking(LPC_I2C0, &i2cData) == 0) { + return ERROR; + } + return SUCCESS; +} + +static Status I2CRead(uint32_t addr, uint8_t* buf, uint32_t len) +{ + I2CM_XFER_T i2cData; + + i2cData.slaveAddr = addr; + i2cData.options = 0; + i2cData.status = 0; + i2cData.txBuff = NULL; + i2cData.txSz = 0; + i2cData.rxBuff = buf; + i2cData.rxSz = len; + + if (Chip_I2CM_XferBlocking(LPC_I2C0, &i2cData) == 0) { + return ERROR; + } + return SUCCESS; +} + +static void setLsStates(uint16_t states, uint8_t* ls, uint8_t mode) +{ +#define IS_LED_SET(bit, x) ( ( ((x) & (bit)) != 0 ) ? 1 : 0 ) + + int i = 0; + + for (i = 0; i < 4; i++) { + + ls[i] |= ( (IS_LED_SET(0x0001, states)*mode << 0) + | (IS_LED_SET(0x0002, states)*mode << 2) + | (IS_LED_SET(0x0004, states)*mode << 4) + | (IS_LED_SET(0x0008, states)*mode << 6) ); + + states >>= 4; + } +} + +static void setLeds(void) +{ + uint8_t buf[5]; + uint8_t ls[4] = {0,0,0,0}; + uint16_t states = ledStateShadow; + + /* LEDs in On/Off state */ + setLsStates(states, ls, LS_MODE_ON); + + /* set the LEDs that should blink */ + setLsStates(blink0Shadow, ls, LS_MODE_BLINK0); + setLsStates(blink1Shadow, ls, LS_MODE_BLINK1); + + + buf[0] = PCA9532_LS0 | PCA9532_AUTO_INC; + buf[1] = ls[0]; + buf[2] = ls[1]; + buf[3] = ls[2]; + buf[4] = ls[3]; + I2CWrite(PCA9532_I2C_ADDR, buf, 5); +} + +/****************************************************************************** + * Public Functions + *****************************************************************************/ + +/****************************************************************************** + * + * Description: + * Initialize the PCA9532 Device + * + *****************************************************************************/ +void pca9532_init (void) +{ + /* nothing to initialize */ +} + +/****************************************************************************** + * + * Description: + * Get the LED states + * + * Params: + * [in] shadow - TRUE if the states should be retrieved from the shadow + * variables. The shadow variable are updated when any + * of setLeds, setBlink0Leds and/or setBlink1Leds are + * called. + * + * FALSE if the state should be retrieved from the PCA9532 + * device. A blinkin LED may be reported as on or off + * depending on the state when calling the function. + * + * Returns: + * A mask where a 1 indicates that a LED is on (or blinking). + * + *****************************************************************************/ +uint16_t pca9532_getLedState (uint32_t shadow) +{ + uint8_t buf[2]; + uint16_t ret = 0; + + if (shadow) { + /* a blink LED is reported as on*/ + ret = (ledStateShadow | blink0Shadow | blink1Shadow); + } + else { + + /* + * A blinking LED may be reported as on or off depending on + * its state when reading the Input register. + */ + + buf[0] = PCA9532_INPUT0; + I2CWrite(PCA9532_I2C_ADDR, buf, 1); + + I2CRead(PCA9532_I2C_ADDR, buf, 1); + ret = buf[0]; + + + buf[0] = PCA9532_INPUT1; + I2CWrite(PCA9532_I2C_ADDR, buf, 1); + + I2CRead(PCA9532_I2C_ADDR, buf, 1); + ret |= (buf[0] << 8); + + + /* invert since LEDs are active low */ + ret = ((~ret) & 0xFFFF); + } + + return (ret & ~PCA9532_NOT_USED); +} + + +/****************************************************************************** + * + * Description: + * Set LED states (on or off). + * + * Params: + * [in] ledOnMask - The LEDs that should be turned on. This mask has + * priority over ledOffMask + * [in] ledOffMask - The LEDs that should be turned off. + * + *****************************************************************************/ +void pca9532_setLeds (uint16_t ledOnMask, uint16_t ledOffMask) +{ + /* turn off leds */ + ledStateShadow &= (~(ledOffMask) & 0xffff); + + /* ledOnMask has priority over ledOffMask */ + ledStateShadow |= ledOnMask; + + /* turn off blinking */ + blink0Shadow &= (~(ledOffMask) & 0xffff); + blink1Shadow &= (~(ledOffMask) & 0xffff); + + setLeds(); +} + +/****************************************************************************** + * + * Description: + * Set the blink period for PWM0. Valid values are 0 - 255 where 0 + * means 152 Hz and 255 means 0.59 Hz. A value of 151 means 1 Hz. + * + * Params: + * [in] period - the period for pwm0 + * + *****************************************************************************/ +void pca9532_setBlink0Period(uint8_t period) +{ + uint8_t buf[2]; + + buf[0] = PCA9532_PSC0; + buf[1] = period; + I2CWrite(PCA9532_I2C_ADDR, buf, 2); +} + +/****************************************************************************** + * + * Description: + * Set the duty cycle for PWM0. Valid values are 0 - 100. 25 means the LED + * is on 25% of the period. + * + * Params: + * [in] duty - duty cycle + * + *****************************************************************************/ +void pca9532_setBlink0Duty(uint8_t duty) +{ + uint8_t buf[2]; + uint32_t tmp = duty; + if (tmp > 100) { + tmp = 100; + } + + tmp = (256 * tmp)/100; + + buf[0] = PCA9532_PWM0; + buf[1] = tmp; + I2CWrite(PCA9532_I2C_ADDR, buf, 2); +} + +/****************************************************************************** + * + * Description: + * Set the LEDs that should blink with rate and duty cycle from PWM0. + * Blinking is turned off with pca9532_setLeds. + * + * Params: + * [in] ledMask - LEDs that should blink. + * + *****************************************************************************/ +void pca9532_setBlink0Leds(uint16_t ledMask) +{ + blink0Shadow |= ledMask; + setLeds(); +} + +/****************************************************************************** + * + * Description: + * Set the blink period for PWM1. Valid values are 0 - 255 where 0 + * means 152 Hz and 255 means 0.59 Hz. A value of 151 means 1 Hz. + * + * Params: + * [in] period - The period for PWM1 + * + *****************************************************************************/ +void pca9532_setBlink1Period(uint8_t period) +{ + uint8_t buf[2]; + + buf[0] = PCA9532_PSC1; + buf[1] = period; + I2CWrite(PCA9532_I2C_ADDR, buf, 2); +} + +/****************************************************************************** + * + * Description: + * Set the duty cycle for PWM1. Valid values are 0 - 100. 25 means the LED + * is on 25% of the period. + * + * Params: + * [in] duty - duty cycle. + * + *****************************************************************************/ +void pca9532_setBlink1Duty(uint8_t duty) +{ + uint8_t buf[2]; + + uint32_t tmp = duty; + if (tmp > 100) { + tmp = 100; + } + + tmp = (256 * tmp)/100; + + buf[0] = PCA9532_PWM1; + buf[1] = tmp; + I2CWrite(PCA9532_I2C_ADDR, buf, 2); +} + +/****************************************************************************** + * + * Description: + * Set the LEDs that should blink with rate and duty cycle from PWM1. + * Blinking is turned off with pca9532_setLeds. + * + * Params: + * [in] ledMask - LEDs that should blink. + * + *****************************************************************************/ +void pca9532_setBlink1Leds(uint16_t ledMask) +{ + blink1Shadow |= ledMask; + setLeds(); +} diff --git a/hw/bsp/lpc43/boards/ea4357/pca9532.h b/hw/bsp/lpc43/boards/ea4357/pca9532.h new file mode 100644 index 000000000..f21c1ff09 --- /dev/null +++ b/hw/bsp/lpc43/boards/ea4357/pca9532.h @@ -0,0 +1,94 @@ +/***************************************************************************** + * + * Copyright(C) 2011, Embedded Artists AB + * All rights reserved. + * + ****************************************************************************** + * Software that is described herein is for illustrative purposes only + * which provides customers with programming information regarding the + * products. This software is supplied "AS IS" without any warranties. + * Embedded Artists AB assumes no responsibility or liability for the + * use of the software, conveys no license or title under any patent, + * copyright, or mask work right to the product. Embedded Artists AB + * reserves the right to make changes in the software without + * notification. Embedded Artists AB also make no representation or + * warranty that such application will be suitable for the specified + * use without further testing or modification. + *****************************************************************************/ +#ifndef __PCA9532C_H +#define __PCA9532C_H + + +#define PCA9532_I2C_ADDR (0xC0>>1) + +#define PCA9532_INPUT0 0x00 +#define PCA9532_INPUT1 0x01 +#define PCA9532_PSC0 0x02 +#define PCA9532_PWM0 0x03 +#define PCA9532_PSC1 0x04 +#define PCA9532_PWM1 0x05 +#define PCA9532_LS0 0x06 +#define PCA9532_LS1 0x07 +#define PCA9532_LS2 0x08 +#define PCA9532_LS3 0x09 + +#define PCA9532_AUTO_INC 0x10 + + +/* + * The Keys on the base board are mapped to LED0 -> LED3 on + * the PCA9532. + */ + +#define KEY1 0x0001 +#define KEY2 0x0002 +#define KEY3 0x0004 +#define KEY4 0x0008 + +#define KEY_MASK 0x000F + +/* + * MMC Card Detect and MMC Write Protect are mapped to LED4 + * and LED5 on the PCA9532. Please note that WP is active low. + */ + +#define MMC_CD 0x0010 +#define MMC_WP 0x0020 + +#define MMC_MASK 0x30 + +/* NOTE: LED6 and LED7 on PCA9532 are not connected to anything */ +#define PCA9532_NOT_USED 0xC0 + +/* + * Below are the LED constants to use when enabling/disabling a LED. + * The LED names are the names printed on the base board and not + * the names from the PCA9532 device. base_LED1 -> LED8 on PCA9532, + * base_LED2 -> LED9, and so on. + */ + +#define LED1 0x0100 +#define LED2 0x0200 +#define LED3 0x0400 +#define LED4 0x0800 +#define LED5 0x1000 +#define LED6 0x2000 +#define LED7 0x4000 +#define LED8 0x8000 + +#define LED_MASK 0xFF00 + +void pca9532_init (void); +uint16_t pca9532_getLedState (uint32_t shadow); +void pca9532_setLeds (uint16_t ledOnMask, uint16_t ledOffMask); +void pca9532_setBlink0Period(uint8_t period); +void pca9532_setBlink0Duty(uint8_t duty); +void pca9532_setBlink0Leds(uint16_t ledMask); +void pca9532_setBlink1Period(uint8_t period); +void pca9532_setBlink1Duty(uint8_t duty); +void pca9532_setBlink1Leds(uint16_t ledMask); + +#endif /* end __PCA9532C_H */ +/**************************************************************************** +** End Of File +*****************************************************************************/ diff --git a/hw/bsp/lpc43/family.c b/hw/bsp/lpc43/family.c new file mode 100644 index 000000000..ba3191d5f --- /dev/null +++ b/hw/bsp/lpc43/family.c @@ -0,0 +1,312 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +// Suppress warning caused by mcu driver +#ifdef __GNUC__ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wunused-parameter" +#endif + +#include "chip.h" + +#ifdef __GNUC__ +#pragma GCC diagnostic pop +#endif + +#include "bsp/board_api.h" +#include "board.h" + +#define UART_DEV LPC_USART0 +#define UART_PORT 0x0f +#define UART_PIN_TX 10 +#define UART_PIN_RX 11 + +// P9_1 joystick down +#define BUTTON_PORT 4 +#define BUTTON_PIN 13 + +//static const struct { +// uint8_t mux_port; +// uint8_t mux_pin; +// +// uint8_t gpio_port; +// uint8_t gpio_pin; +//}buttons[] = +//{ +// {0x0a, 3, 4, 10 }, // Joystick up +// {0x09, 1, 4, 13 }, // Joystick down +// {0x0a, 2, 4, 9 }, // Joystick left +// {0x09, 0, 4, 12 }, // Joystick right +// {0x0a, 1, 4, 8 }, // Joystick press +// {0x02, 7, 0, 7 }, // SW6 +//}; + +#ifdef BOARD_TUD_RHPORT + #define PORT_SUPPORT_DEVICE(_n) (BOARD_TUD_RHPORT == _n) +#else + #define PORT_SUPPORT_DEVICE(_n) 0 +#endif + +#ifdef BOARD_TUH_RHPORT + #define PORT_SUPPORT_HOST(_n) (BOARD_TUH_RHPORT == _n) +#else + #define PORT_SUPPORT_HOST(_n) 0 +#endif + +/*------------------------------------------------------------------*/ +/* BOARD API + *------------------------------------------------------------------*/ + +/* System configuration variables used by chip driver */ +const uint32_t OscRateIn = 12000000; +const uint32_t ExtRateIn = 0; + +static const PINMUX_GRP_T pinmuxing[] = +{ + // Button ( Joystick down ) + {0x9, 1, (SCU_MODE_INBUFF_EN | SCU_MODE_INACT | SCU_MODE_FUNC0 | SCU_MODE_PULLUP)}, + + // UART + {UART_PORT, UART_PIN_TX, SCU_MODE_PULLDOWN | SCU_MODE_FUNC1}, + {UART_PORT, UART_PIN_RX, SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_FUNC1}, + + // USB +}; + +/* Pin clock mux values, re-used structure, value in first index is meaningless */ +static const PINMUX_GRP_T pinclockmuxing[] = +{ + {0, 0, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)}, + {0, 1, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)}, + {0, 2, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)}, + {0, 3, (SCU_MODE_INACT | SCU_MODE_INBUFF_EN | SCU_MODE_ZIF_DIS | SCU_MODE_HIGHSPEEDSLEW_EN | SCU_MODE_FUNC0)}, +}; + +// Invoked by startup code +void SystemInit(void) +{ +#ifdef __USE_LPCOPEN + extern void (* const g_pfnVectors[])(void); + unsigned int *pSCB_VTOR = (unsigned int *) 0xE000ED08; + *pSCB_VTOR = (unsigned int) g_pfnVectors; + +#if __FPU_USED == 1 + fpuInit(); +#endif +#endif // __USE_LPCOPEN + + /* Setup system level pin muxing */ + Chip_SCU_SetPinMuxing(pinmuxing, sizeof(pinmuxing) / sizeof(PINMUX_GRP_T)); + + /* Clock pins only, group field not used */ + for (int i = 0; i <(int) (sizeof(pinclockmuxing) / sizeof(pinclockmuxing[0])); i++) + { + Chip_SCU_ClockPinMuxSet(pinclockmuxing[i].pinnum, pinclockmuxing[i].modefunc); + } + + Chip_SetupXtalClocking(); +} + +void board_init(void) +{ + SystemCoreClockUpdate(); + +#if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); +#elif CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); +#endif + + Chip_GPIO_Init(LPC_GPIO_PORT); + + // LED via pca9532 I2C + Chip_SCU_I2C0PinConfig(I2C0_STANDARD_FAST_MODE); + Chip_I2C_Init(I2C0); + Chip_I2C_SetClockRate(I2C0, 100000); + Chip_I2C_SetMasterEventHandler(I2C0, Chip_I2C_EventHandlerPolling); + + pca9532_init(); + + // Button + Chip_GPIO_SetPinDIRInput(LPC_GPIO_PORT, BUTTON_PORT, BUTTON_PIN); + + //------------- UART -------------// + Chip_UART_Init(UART_DEV); + Chip_UART_SetBaud(UART_DEV, CFG_BOARD_UART_BAUDRATE); + Chip_UART_ConfigData(UART_DEV, UART_LCR_WLEN8 | UART_LCR_SBS_1BIT | UART_LCR_PARITY_DIS); + Chip_UART_TXEnable(UART_DEV); + + //------------- USB -------------// + enum { + USBMODE_DEVICE = 2, + USBMODE_HOST = 3 + }; + + enum { + USBMODE_VBUS_LOW = 0, + USBMODE_VBUS_HIGH = 1 + }; + + /* From EA4357 user manual + * + * USB0 Device operation: + * - Insert jumpers in position 1-2 in JP17/JP18/JP19. + * - GPIO28 controls USB connect functionality + * - LED32 lights when the USB Device is connected. SJ4 has pads 1-2 shorted by default. + * - LED33 is controlled by GPIO27 and signals USB-up state. GPIO54 is used for VBUS + * sensing. + * + * USB0 Host operation: + * - insert jumpers in position 2-3 in JP17/JP18/JP19. + * - USB Host power is controlled via distribution switch U20 (found in schematic page 11). + * - Signal GPIO26 is active low and enables +5V on VBUS2. + * - LED35 light whenever +5V is present on VBUS2. + * - GPIO55 is connected to status feedback from the distribution switch. + * - GPIO54 is used for VBUS sensing. 15Kohm pull-down resistors are always active + * + * Note: + * - Insert jumpers in position 2-3 in JP17/JP18/JP19 + * - Insert jumpers in JP31 (OTG) + */ +#if PORT_SUPPORT_DEVICE(0) || PORT_SUPPORT_HOST(0) + Chip_USB0_Init(); +#endif + + /* From EA4357 user manual + * + * For USB1 Device: + * - a 1.5Kohm pull-up resistor is needed on the USB DP data signal. There are two methods to create this. + * JP15 is inserted and the pull-up resistor is always enabled. Alternatively, the pull-up resistor is activated + * inside the USB OTG chip (U31), and this has to be done via the I2C interface of GPIO52/GPIO53. In the latter case, + * JP15 shall not be inserted. + * - J19 is the connector to use when USB Device is used. Normally it should be a USB-B connector for + * creating a USB Device interface, but the mini-AB connector can also be used in this case. The status + * of VBUS can be read via U31. + * - JP16 shall not be inserted. + * + * For USB1 Host: + * - 15Kohm pull-down resistors are needed on the USB data signals. These are activated inside the USB OTG chip (U31), + * and this has to be done via the I2C interface of GPIO52/GPIO53. + * - J20 is the connector to use when USB Host is used. In order to provide +5V to the external USB + * device connected to this connector (J20), channel A of U20 must be enabled. It is enabled by default + * since SJ5 is normally connected between pin 1-2. + * - LED34 lights green when +5V is available on J20. + * - JP15 shall not be inserted. JP16 has no effect + */ +#if PORT_SUPPORT_DEVICE(1) || PORT_SUPPORT_HOST(1) + Chip_USB1_Init(); +#endif + + // USB0 Vbus Power: P2_3 on EA4357 channel B U20 GPIO26 active low (base board) + Chip_SCU_PinMuxSet(2, 3, SCU_MODE_PULLUP | SCU_MODE_INBUFF_EN | SCU_MODE_FUNC7); + + #if PORT_SUPPORT_DEVICE(0) + // P9_5 (GPIO5[18]) (GPIO28 on oem base) as USB connect, active low. + Chip_SCU_PinMuxSet(9, 5, SCU_MODE_PULLDOWN | SCU_MODE_FUNC4); + Chip_GPIO_SetPinDIROutput(LPC_GPIO_PORT, 5, 18); + #endif + + // USB1 Power: EA4357 channel A U20 is enabled by SJ5 connected to pad 1-2, no more action required + // TODO Remove R170, R171, solder a pair of 15K to USB1 D+/D- to test with USB1 Host +} + +//--------------------------------------------------------------------+ +// USB Interrupt Handler +//--------------------------------------------------------------------+ +void USB0_IRQHandler(void) +{ + #if PORT_SUPPORT_DEVICE(0) + tud_int_handler(0); + #endif + + #if PORT_SUPPORT_HOST(0) + tuh_int_handler(0); + #endif +} + +void USB1_IRQHandler(void) +{ + #if PORT_SUPPORT_DEVICE(1) + tud_int_handler(1); + #endif + + #if PORT_SUPPORT_HOST(1) + tuh_int_handler(1); + #endif +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + if (state) + { + pca9532_setLeds( LED1, 0 ); + }else + { + pca9532_setLeds( 0, LED1); + } +} + +uint32_t board_button_read(void) +{ + // active low + return Chip_GPIO_GetPinState(LPC_GPIO_PORT, BUTTON_PORT, BUTTON_PIN) ? 0 : 1; +} + +int board_uart_read(uint8_t* buf, int len) +{ + return Chip_UART_Read(UART_DEV, buf, len); +} + +int board_uart_write(void const * buf, int len) +{ + uint8_t const* buf8 = (uint8_t const*) buf; + for(int i=0; i Date: Tue, 18 Jul 2023 14:23:41 +0200 Subject: clean(ra_hcd): fix typos in the hcd library --- src/portable/renesas/rusb2/hcd_rusb2.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 55bf6de4d..790cd6b32 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -265,7 +265,7 @@ static bool pipe_xfer_in(rusb2_reg_t* rusb, unsigned num) pipe->buf = (uint8_t*)buf + len; } if (len < mps) { - rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BCLR_Msk; + rusb->D0FIFOCTR = RUSB2_D0FIFOCTR_BCLR_Msk; } rusb->D0FIFOSEL = 0; while (rusb->D0FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ @@ -297,7 +297,7 @@ static bool pipe_xfer_out(rusb2_reg_t* rusb, unsigned num) pipe->buf = (uint8_t*)buf + len; } if (len < mps) { - rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + rusb->D0FIFOCTR = RUSB2_D0FIFOCTR_BVAL_Msk; } rusb->D0FIFOSEL = 0; while (rusb->D0FIFOSEL_b.CURPIPE) ; /* if CURPIPE bits changes, check written value */ @@ -367,7 +367,7 @@ static bool process_pipe_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, } else { /* ZLP */ rusb->D0FIFOSEL = num; pipe_wait_for_ready(rusb, num); - rusb->D0FIFOCTR = RUSB2_CFIFOCTR_BVAL_Msk; + rusb->D0FIFOCTR = RUSB2_D0FIFOCTR_BVAL_Msk; rusb->D0FIFOSEL = 0; while (rusb->D0FIFOSEL_b.CURPIPE) {} /* if CURPIPE bits changes, check written value */ } -- cgit v1.3.1 From 1f95a417f271e627ec981be3d211eed8c37cb052 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 7 Aug 2023 18:22:28 +0700 Subject: Add tuh_rhport_is_active() and tuh_rhport_reset_bus() - also improve ehci bus reset - seperate bus reset delay and contact debouncing delay in enumeration --- src/host/hcd.h | 5 +- src/host/hub.c | 2 +- src/host/usbh.c | 118 +++++++++++++++++--------------- src/host/usbh.h | 39 ++++++----- src/portable/chipidea/ci_hs/hcd_ci_hs.c | 43 ++++++------ src/portable/ehci/ehci.c | 24 +++++-- 6 files changed, 128 insertions(+), 103 deletions(-) (limited to 'src/portable') diff --git a/src/host/hcd.h b/src/host/hcd.h index d77dd6e2f..9bcc1c6df 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -149,10 +149,11 @@ uint32_t hcd_frame_number(uint8_t rhport); // Get the current connect status of roothub port bool hcd_port_connect_status(uint8_t rhport); -// Reset USB bus on the port +// Reset USB bus on the port. Return immediately, bus reset sequence may not be complete. +// Some port would require hcd_port_reset_end() to be invoked after 10ms to complete the reset sequence. void hcd_port_reset(uint8_t rhport); -// TODO implement later +// Complete bus reset sequence, may be required by some controllers void hcd_port_reset_end(uint8_t rhport); // Get port link speed diff --git a/src/host/hub.c b/src/host/hub.c index 16dd534d2..ec30eb96a 100644 --- a/src/host/hub.c +++ b/src/host/hub.c @@ -330,7 +330,7 @@ static void connection_port_reset_complete (tuh_xfer_t* xfer); bool hub_xfer_cb(uint8_t dev_addr, uint8_t ep_addr, xfer_result_t result, uint32_t xferred_bytes) { (void) xferred_bytes; // TODO can be more than 1 for hub with lots of ports (void) ep_addr; - TU_ASSERT(result == XFER_RESULT_SUCCESS); + TU_VERIFY(result == XFER_RESULT_SUCCESS); hub_interface_t* p_hub = get_itf(dev_addr); diff --git a/src/host/usbh.c b/src/host/usbh.c index 49f8c78f1..cc7e38b45 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -181,9 +181,6 @@ static usbh_class_driver_t const usbh_class_drivers[] = }; enum { USBH_CLASS_DRIVER_COUNT = TU_ARRAY_SIZE(usbh_class_drivers) }; - -enum { RESET_DELAY = 500 }; // 200 USB specs say only 50ms but many devices require much longer - enum { CONFIG_NUM = 1 }; // default to use configuration 1 @@ -251,40 +248,27 @@ static bool usbh_control_xfer_cb (uint8_t daddr, uint8_t ep_addr, xfer_result_t #if CFG_TUSB_OS == OPT_OS_NONE // TODO rework time-related function later -TU_ATTR_WEAK void osal_task_delay(uint32_t msec) -{ +// weak and overridable +TU_ATTR_WEAK void osal_task_delay(uint32_t msec) { const uint32_t start = hcd_frame_number(_usbh_controller); while ( ( hcd_frame_number(_usbh_controller) - start ) < msec ) {} } #endif //--------------------------------------------------------------------+ -// PUBLIC API (Parameter Verification is required) +// Device API //--------------------------------------------------------------------+ -bool tuh_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) -{ - if (hcd_configure) - { - return hcd_configure(rhport, cfg_id, cfg_param); - }else - { - return false; - } -} - -bool tuh_mounted(uint8_t dev_addr) -{ - usbh_device_t* dev = get_device(dev_addr); +bool tuh_mounted(uint8_t dev_addr) { + usbh_device_t *dev = get_device(dev_addr); TU_VERIFY(dev); return dev->configured; } -bool tuh_vid_pid_get(uint8_t dev_addr, uint16_t* vid, uint16_t* pid) -{ +bool tuh_vid_pid_get(uint8_t dev_addr, uint16_t *vid, uint16_t *pid) { *vid = *pid = 0; - usbh_device_t const* dev = get_device(dev_addr); + usbh_device_t const *dev = get_device(dev_addr); TU_VERIFY(dev && dev->addressed && dev->vid != 0); *vid = dev->vid; @@ -293,26 +277,48 @@ bool tuh_vid_pid_get(uint8_t dev_addr, uint16_t* vid, uint16_t* pid) return true; } -tusb_speed_t tuh_speed_get (uint8_t dev_addr) -{ - usbh_device_t* dev = get_device(dev_addr); +tusb_speed_t tuh_speed_get(uint8_t dev_addr) { + usbh_device_t *dev = get_device(dev_addr); return (tusb_speed_t) (dev ? get_device(dev_addr)->speed : _dev0.speed); } -static void clear_device(usbh_device_t* dev) -{ +bool tuh_rhport_is_active(uint8_t rhport) { + return _usbh_controller == rhport; +} + +bool tuh_rhport_reset_bus(uint8_t rhport, bool active) { + TU_VERIFY(tuh_rhport_is_active(rhport)); + if ( active ) { + hcd_port_reset(rhport); + } else { + hcd_port_reset_end(rhport); + } + return true; +} + +//--------------------------------------------------------------------+ +// PUBLIC API (Parameter Verification is required) +//--------------------------------------------------------------------+ + +bool tuh_configure(uint8_t rhport, uint32_t cfg_id, const void *cfg_param) { + if ( hcd_configure ) { + return hcd_configure(rhport, cfg_id, cfg_param); + } else { + return false; + } +} + +static void clear_device(usbh_device_t* dev) { tu_memclr(dev, sizeof(usbh_device_t)); memset(dev->itf2drv, TUSB_INDEX_INVALID_8, sizeof(dev->itf2drv)); // invalid mapping memset(dev->ep2drv , TUSB_INDEX_INVALID_8, sizeof(dev->ep2drv )); // invalid mapping } -bool tuh_inited(void) -{ +bool tuh_inited(void) { return _usbh_controller != TUSB_INDEX_INVALID_8; } -bool tuh_init(uint8_t controller_id) -{ +bool tuh_init(uint8_t controller_id) { // skip if already initialized if ( tuh_inited() ) return true; @@ -359,8 +365,7 @@ bool tuh_init(uint8_t controller_id) return true; } -bool tuh_task_event_ready(void) -{ +bool tuh_task_event_ready(void) { // Skip if stack is not initialized if ( !tuh_inited() ) return false; @@ -385,8 +390,7 @@ bool tuh_task_event_ready(void) } @endcode */ -void tuh_task_ext(uint32_t timeout_ms, bool in_isr) -{ +void tuh_task_ext(uint32_t timeout_ms, bool in_isr) { (void) in_isr; // not implemented yet // Skip if stack is not initialized @@ -403,8 +407,7 @@ void tuh_task_ext(uint32_t timeout_ms, bool in_isr) case HCD_EVENT_DEVICE_ATTACH: // due to the shared _usbh_ctrl_buf, we must complete enumerating // one device before enumerating another one. - if ( _dev0.enumerating ) - { + if ( _dev0.enumerating ) { TU_LOG_USBH("[%u:] USBH Defer Attach until current enumeration complete\r\n", event.rhport); bool is_empty = osal_queue_empty(_usbh_q); @@ -414,8 +417,7 @@ void tuh_task_ext(uint32_t timeout_ms, bool in_isr) // Exit if this is the only event in the queue, otherwise we may loop forever return; } - }else - { + }else { TU_LOG_USBH("[%u:] USBH DEVICE ATTACH\r\n", event.rhport); _dev0.enumerating = 1; enum_new_device(&event); @@ -428,8 +430,7 @@ void tuh_task_ext(uint32_t timeout_ms, bool in_isr) #if CFG_TUH_HUB // TODO remove - if ( event.connection.hub_addr != 0) - { + if ( event.connection.hub_addr != 0) { // done with hub, waiting for next data on status pipe (void) hub_edpt_status_xfer( event.connection.hub_addr ); } @@ -1230,6 +1231,12 @@ static void process_removing_device(uint8_t rhport, uint8_t hub_addr, uint8_t hu // one device before enumerating another one. //--------------------------------------------------------------------+ +enum { + ENUM_RESET_DELAY = 50, // USB specs: 10 to 50ms + ENUM_CONTACT_DEBOUNCING_DELAY = 450, // when plug/unplug a device, physical connection can be bouncing and may + // generate a series of attach/detach event. This delay wait for stable connection +}; + enum { ENUM_IDLE, ENUM_RESET_1, // 1st reset when attached @@ -1311,7 +1318,7 @@ static void process_enumeration(tuh_xfer_t* xfer) break; case ENUM_HUB_GET_STATUS_2: - osal_task_delay(RESET_DELAY); + osal_task_delay(ENUM_RESET_DELAY); TU_ASSERT( hub_port_get_status(_dev0.hub_addr, _dev0.hub_port, _usbh_ctrl_buf, process_enumeration, ENUM_HUB_CLEAR_RESET_2), ); break; @@ -1468,12 +1475,14 @@ static bool enum_new_device(hcd_event_t* event) if (_dev0.hub_addr == 0) { // connected/disconnected directly with roothub - // wait until device is stable TODO non blocking hcd_port_reset(_dev0.rhport); - osal_task_delay(RESET_DELAY); // TODO may not work for no-OS on MCU that require reset_end() since - // sof of controller may not running while resetting + osal_task_delay(ENUM_RESET_DELAY); // TODO may not work for no-OS on MCU that require reset_end() since + // sof of controller may not running while resetting hcd_port_reset_end( _dev0.rhport); + // wait until device connection is stable TODO non blocking + osal_task_delay(ENUM_CONTACT_DEBOUNCING_DELAY); + // device unplugged while delaying if ( !hcd_port_connect_status(_dev0.rhport) ) { enum_full_complete(); @@ -1489,6 +1498,7 @@ static bool enum_new_device(hcd_event_t* event) xfer.result = XFER_RESULT_SUCCESS; xfer.user_data = ENUM_ADDR0_DEVICE_DESC; + process_enumeration(&xfer); } @@ -1496,8 +1506,8 @@ static bool enum_new_device(hcd_event_t* event) else { // connected/disconnected via external hub - // wait until device is stable - osal_task_delay(RESET_DELAY); + // wait until device connection is stable TODO non blocking + osal_task_delay(ENUM_CONTACT_DEBOUNCING_DELAY); // ENUM_HUB_GET_STATUS //TU_ASSERT( hub_port_get_status(_dev0.hub_addr, _dev0.hub_port, _usbh_ctrl_buf, enum_hub_get_status0_complete, 0) ); @@ -1508,23 +1518,19 @@ static bool enum_new_device(hcd_event_t* event) return true; } -static uint8_t get_new_address(bool is_hub) -{ +static uint8_t get_new_address(bool is_hub) { uint8_t start; uint8_t end; - if ( is_hub ) - { + if ( is_hub ) { start = CFG_TUH_DEVICE_MAX; end = start + CFG_TUH_HUB; - }else - { + }else { start = 0; end = start + CFG_TUH_DEVICE_MAX; } - for (uint8_t idx = start; idx < end; idx++) - { + for (uint8_t idx = start; idx < end; idx++) { if (!_usbh_devices[idx].connected) return (idx+1); } diff --git a/src/host/usbh.h b/src/host/usbh.h index 0d56f40c9..684e8240e 100644 --- a/src/host/usbh.h +++ b/src/host/usbh.h @@ -47,8 +47,7 @@ typedef void (*tuh_xfer_cb_t)(tuh_xfer_t* xfer); // it is advised to initialize it using member name // Note2: not all field is available/meaningful in callback, // some info is not saved by usbh to save SRAM -struct tuh_xfer_s -{ +struct tuh_xfer_s { uint8_t daddr; uint8_t ep_addr; uint8_t TU_RESERVED; // reserved @@ -56,8 +55,7 @@ struct tuh_xfer_s uint32_t actual_len; // excluding setup packet - union - { + union { tusb_control_request_t const* setup; // setup packet pointer if control transfer uint32_t buflen; // expected length if not control transfer (not available in callback) }; @@ -70,15 +68,13 @@ struct tuh_xfer_s }; // Subject to change -typedef struct -{ +typedef struct { uint8_t daddr; tusb_desc_interface_t desc; } tuh_itf_info_t; // ConfigID for tuh_config() -enum -{ +enum { TUH_CFGID_RPI_PIO_USB_CONFIGURATION = OPT_MCU_RP2040 << 8 // cfg_param: pio_usb_configuration_t }; @@ -105,12 +101,12 @@ TU_ATTR_WEAK void tuh_umount_cb(uint8_t daddr); // Should be called before tuh_init() // - cfg_id : configure ID (TBD) // - cfg_param: configure data, structure depends on the ID -bool tuh_configure(uint8_t controller_id, uint32_t cfg_id, const void* cfg_param); +bool tuh_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param); // Init host stack -bool tuh_init(uint8_t controller_id); +bool tuh_init(uint8_t rhport); -// Check if host stack is already initialized +// Check if host stack is already initialized with any roothub ports bool tuh_inited(void); // Task function should be called in main/rtos loop, extended version of tuh_task() @@ -120,8 +116,7 @@ void tuh_task_ext(uint32_t timeout_ms, bool in_isr); // Task function should be called in main/rtos loop TU_ATTR_ALWAYS_INLINE static inline -void tuh_task(void) -{ +void tuh_task(void) { tuh_task_ext(UINT32_MAX, false); } @@ -135,8 +130,20 @@ extern void hcd_int_handler(uint8_t rhport); // Interrupt handler, name alias to HCD #define tuh_int_handler hcd_int_handler +// Check if roothub port is initialized and active as a host +bool tuh_rhport_is_active(uint8_t rhport); + +// Assert/de-assert Bus Reset signal to roothub port. USB specs: it should last 10-50ms +bool tuh_rhport_reset_bus(uint8_t rhport, bool active); + +//--------------------------------------------------------------------+ +// Device API +//--------------------------------------------------------------------+ + +// Get VID/PID of device bool tuh_vid_pid_get(uint8_t daddr, uint16_t* vid, uint16_t* pid); +// Get speed of device tusb_speed_t tuh_speed_get(uint8_t daddr); // Check if device is connected and configured @@ -144,8 +151,7 @@ bool tuh_mounted(uint8_t daddr); // Check if device is suspended TU_ATTR_ALWAYS_INLINE static inline -bool tuh_suspended(uint8_t daddr) -{ +bool tuh_suspended(uint8_t daddr) { // TODO implement suspend & resume on host (void) daddr; return false; @@ -153,8 +159,7 @@ bool tuh_suspended(uint8_t daddr) // Check if device is ready to communicate with TU_ATTR_ALWAYS_INLINE static inline -bool tuh_ready(uint8_t daddr) -{ +bool tuh_ready(uint8_t daddr) { return tuh_mounted(daddr) && !tuh_suspended(daddr); } diff --git a/src/portable/chipidea/ci_hs/hcd_ci_hs.c b/src/portable/chipidea/ci_hs/hcd_ci_hs.c index 6ee91e18e..462cbd301 100644 --- a/src/portable/chipidea/ci_hs/hcd_ci_hs.c +++ b/src/portable/chipidea/ci_hs/hcd_ci_hs.c @@ -39,24 +39,27 @@ #include "ci_hs_type.h" #if CFG_TUSB_MCU == OPT_MCU_MIMXRT1XXX - #include "ci_hs_imxrt.h" - bool hcd_dcache_clean(void const* addr, uint32_t data_size) { - return imxrt_dcache_clean(addr, data_size); - } +#include "ci_hs_imxrt.h" - bool hcd_dcache_invalidate(void const* addr, uint32_t data_size) { - return imxrt_dcache_invalidate(addr, data_size); - } +bool hcd_dcache_clean(void const* addr, uint32_t data_size) { + return imxrt_dcache_clean(addr, data_size); +} + +bool hcd_dcache_invalidate(void const* addr, uint32_t data_size) { + return imxrt_dcache_invalidate(addr, data_size); +} - bool hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { - return imxrt_dcache_clean_invalidate(addr, data_size); - } +bool hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) { + return imxrt_dcache_clean_invalidate(addr, data_size); +} #elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) - #include "ci_hs_lpc18_43.h" + +#include "ci_hs_lpc18_43.h" + #else - #error "Unsupported MCUs" +#error "Unsupported MCUs" #endif //--------------------------------------------------------------------+ @@ -67,25 +70,25 @@ // Controller API //--------------------------------------------------------------------+ -bool hcd_init(uint8_t rhport) -{ - ci_hs_regs_t* hcd_reg = CI_HS_REG(rhport); +bool hcd_init(uint8_t rhport) { + ci_hs_regs_t *hcd_reg = CI_HS_REG(rhport); // Reset controller hcd_reg->USBCMD |= USBCMD_RESET; - while( hcd_reg->USBCMD & USBCMD_RESET ) {} + while ( hcd_reg->USBCMD & USBCMD_RESET ) {} // Set mode to device, must be set immediately after reset #if CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_LPC43XX // LPC18XX/43XX need to set VBUS Power Select to HIGH // RHPORT1 is fullspeed only (need external PHY for Highspeed) hcd_reg->USBMODE = USBMODE_CM_HOST | USBMODE_VBUS_POWER_SELECT; - if (rhport == 1) hcd_reg->PORTSC1 |= PORTSC1_FORCE_FULL_SPEED; + if ( rhport == 1 ) hcd_reg->PORTSC1 |= PORTSC1_FORCE_FULL_SPEED; #else hcd_reg->USBMODE = USBMODE_CM_HOST; #endif // FIXME force full speed, still have issue with Highspeed enumeration + // probably due to physical connection bouncing when plug/unplug // 1. Have issue when plug/unplug devices, maybe the port is not reset properly // 2. Also does not seems to detect disconnection hcd_reg->PORTSC1 |= PORTSC1_FORCE_FULL_SPEED; @@ -93,13 +96,11 @@ bool hcd_init(uint8_t rhport) return ehci_init(rhport, (uint32_t) &hcd_reg->CAPLENGTH, (uint32_t) &hcd_reg->USBCMD); } -void hcd_int_enable(uint8_t rhport) -{ +void hcd_int_enable(uint8_t rhport) { CI_HCD_INT_ENABLE(rhport); } -void hcd_int_disable(uint8_t rhport) -{ +void hcd_int_disable(uint8_t rhport) { CI_HCD_INT_DISABLE(rhport); } diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 9be24c888..79811985c 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -188,6 +188,11 @@ void hcd_port_reset(uint8_t rhport) ehci_registers_t* regs = ehci_data.regs; + // skip if already in reset + if (regs->portsc_bm.port_reset) { + return; + } + // mask out Write-1-to-Clear bits uint32_t portsc = regs->portsc & ~EHCI_PORTSC_MASK_W1C; @@ -202,16 +207,18 @@ void hcd_port_reset(uint8_t rhport) void hcd_port_reset_end(uint8_t rhport) { (void) rhport; - -#if 0 // TODO check if this is necessary ehci_registers_t* regs = ehci_data.regs; + // skip if reset is already complete + if (!regs->portsc_bm.port_reset) { + return; + } + // mask out all change bits since they are Write 1 to clear - uint32_t portsc = regs->portsc & ~EHCI_PORTSC_MASK_CHANGE_ALL; - portsc &= ~(EHCI_PORTSC_MASK_PORT_RESET); + uint32_t portsc = regs->portsc & ~EHCI_PORTSC_MASK_W1C; + portsc &= ~EHCI_PORTSC_MASK_PORT_RESET; regs->portsc = portsc; -#endif } bool hcd_port_connect_status(uint8_t rhport) @@ -426,6 +433,11 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet hcd_dcache_clean(setup_packet, 8); + // Control endpoint never be stalled. Skip reset Data Toggle since it is fixed per stage + if (qhd->qtd_overlay.halted) { + qhd->qtd_overlay.halted = false; + } + // attach TD to QHD -> start transferring qhd_attach_qtd(qhd, td); @@ -662,7 +674,7 @@ void hcd_int_handler(uint8_t rhport) if (int_status & EHCI_INT_MASK_PORT_CHANGE) { // Including: Force port resume, over-current change, enable/disable change and connect status change. uint32_t const port_status = regs->portsc & EHCI_PORTSC_MASK_W1C; - print_portsc(regs); + // print_portsc(regs); if (regs->portsc_bm.connect_status_change) { port_connect_status_change_isr(rhport); -- cgit v1.3.1 From 4938971aad2f2a6adb71f4d8ce76e1d4b664092d Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 7 Aug 2023 19:09:36 +0700 Subject: code format --- hw/bsp/lpc18/boards/mcb1800/ozone/lpc1857.jdebug | 5 +- src/portable/raspberrypi/pio_usb/hcd_pio_usb.c | 73 +++++++++--------------- 2 files changed, 29 insertions(+), 49 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/lpc18/boards/mcb1800/ozone/lpc1857.jdebug b/hw/bsp/lpc18/boards/mcb1800/ozone/lpc1857.jdebug index 6e298c62d..f94960f09 100644 --- a/hw/bsp/lpc18/boards/mcb1800/ozone/lpc1857.jdebug +++ b/hw/bsp/lpc18/boards/mcb1800/ozone/lpc1857.jdebug @@ -10,7 +10,7 @@ */ void OnProjectLoad (void) { Project.AddSvdFile ("Cortex-M3.svd"); - Project.AddSvdFile ("./LPC18xx.svd"); + Project.AddSvdFile ("../../../../../../../cmsis-svd/data/NXP/LPC18xx.svd"); Project.SetDevice ("LPC1857"); Project.SetHostIF ("USB", ""); @@ -20,7 +20,8 @@ void OnProjectLoad (void) { Project.SetTraceSource ("Trace Pins"); Project.SetTracePortWidth (4); - File.Open ("../../../../../../examples/device/cdc_msc/cmake-build-mcb1800/cdc_msc.elf"); + //File.Open ("../../../../../../examples/cmake-build-mcb1800/device/cdc_msc/cdc_msc.elf"); + File.Open ("../../../../../../examples/cmake-build-mcb1800/host/cdc_msc_hid/cdc_msc_hid.elf"); } /********************************************************************* * diff --git a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c index adb83e97d..93bc1bf43 100644 --- a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c +++ b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c @@ -48,16 +48,14 @@ static pio_usb_configuration_t pio_host_cfg = PIO_USB_DEFAULT_CONFIG; //--------------------------------------------------------------------+ // HCD API //--------------------------------------------------------------------+ -bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) -{ +bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void *cfg_param) { (void) rhport; TU_VERIFY(cfg_id == TUH_CFGID_RPI_PIO_USB_CONFIGURATION); memcpy(&pio_host_cfg, cfg_param, sizeof(pio_usb_configuration_t)); return true; } -bool hcd_init(uint8_t rhport) -{ +bool hcd_init(uint8_t rhport) { (void) rhport; // To run USB SOF interrupt in core1, call this init in core1 @@ -66,20 +64,17 @@ bool hcd_init(uint8_t rhport) return true; } -void hcd_port_reset(uint8_t rhport) -{ +void hcd_port_reset(uint8_t rhport) { uint8_t const pio_rhport = RHPORT_PIO(rhport); pio_usb_host_port_reset_start(pio_rhport); } -void hcd_port_reset_end(uint8_t rhport) -{ +void hcd_port_reset_end(uint8_t rhport) { uint8_t const pio_rhport = RHPORT_PIO(rhport); pio_usb_host_port_reset_end(pio_rhport); } -bool hcd_port_connect_status(uint8_t rhport) -{ +bool hcd_port_connect_status(uint8_t rhport) { uint8_t const pio_rhport = RHPORT_PIO(rhport); root_port_t *root = PIO_USB_ROOT_PORT(pio_rhport); @@ -88,33 +83,28 @@ bool hcd_port_connect_status(uint8_t rhport) return line_state != PORT_PIN_SE0; } -tusb_speed_t hcd_port_speed_get(uint8_t rhport) -{ +tusb_speed_t hcd_port_speed_get(uint8_t rhport) { // TODO determine link speed uint8_t const pio_rhport = RHPORT_PIO(rhport); return PIO_USB_ROOT_PORT(pio_rhport)->is_fullspeed ? TUSB_SPEED_FULL : TUSB_SPEED_LOW; } // Close all opened endpoint belong to this device -void hcd_device_close(uint8_t rhport, uint8_t dev_addr) -{ +void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { uint8_t const pio_rhport = RHPORT_PIO(rhport); pio_usb_host_close_device(pio_rhport, dev_addr); } -uint32_t hcd_frame_number(uint8_t rhport) -{ +uint32_t hcd_frame_number(uint8_t rhport) { (void) rhport; return pio_usb_host_get_frame_number(); } -void hcd_int_enable(uint8_t rhport) -{ +void hcd_int_enable(uint8_t rhport) { (void) rhport; } -void hcd_int_disable(uint8_t rhport) -{ +void hcd_int_disable(uint8_t rhport) { (void) rhport; } @@ -122,18 +112,16 @@ void hcd_int_disable(uint8_t rhport) // Endpoint API //--------------------------------------------------------------------+ -bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const * desc_ep) -{ +bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const *desc_ep) { hcd_devtree_info_t dev_tree; hcd_devtree_get_info(dev_addr, &dev_tree); bool const need_pre = (dev_tree.hub_addr && dev_tree.speed == TUSB_SPEED_LOW); uint8_t const pio_rhport = RHPORT_PIO(rhport); - return pio_usb_host_endpoint_open(pio_rhport, dev_addr, (uint8_t const*) desc_ep, need_pre); + return pio_usb_host_endpoint_open(pio_rhport, dev_addr, (uint8_t const *) desc_ep, need_pre); } -bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) -{ +bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t *buffer, uint16_t buflen) { uint8_t const pio_rhport = RHPORT_PIO(rhport); return pio_usb_host_endpoint_transfer(pio_rhport, dev_addr, ep_addr, buffer, buflen); } @@ -143,8 +131,7 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { return pio_usb_host_endpoint_abort_transfer(pio_rhport, dev_addr, ep_addr); } -bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) -{ +bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { uint8_t const pio_rhport = RHPORT_PIO(rhport); return pio_usb_host_send_setup(pio_rhport, dev_addr, setup_packet); } @@ -171,18 +158,16 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { return true; } -static void __no_inline_not_in_flash_func(handle_endpoint_irq)(root_port_t* rport, xfer_result_t result, volatile uint32_t* ep_reg) -{ +static void __no_inline_not_in_flash_func(handle_endpoint_irq)(root_port_t *rport, xfer_result_t result, + volatile uint32_t *ep_reg) { (void) rport; const uint32_t ep_all = *ep_reg; - for(uint8_t ep_idx = 0; ep_idx < PIO_USB_EP_POOL_CNT; ep_idx++) - { + for ( uint8_t ep_idx = 0; ep_idx < PIO_USB_EP_POOL_CNT; ep_idx++ ) { uint32_t const mask = (1u << ep_idx); - if (ep_all & mask) - { - endpoint_t* ep = PIO_USB_ENDPOINT(ep_idx); + if ( ep_all & mask ) { + endpoint_t * ep = PIO_USB_ENDPOINT(ep_idx); hcd_event_xfer_complete(ep->dev_addr, ep->ep_num, ep->actual_len, result, true); } } @@ -192,34 +177,28 @@ static void __no_inline_not_in_flash_func(handle_endpoint_irq)(root_port_t* rpor } // IRQ Handler -void __no_inline_not_in_flash_func(pio_usb_host_irq_handler)(uint8_t root_id) -{ +void __no_inline_not_in_flash_func(pio_usb_host_irq_handler)(uint8_t root_id) { uint8_t const tu_rhport = root_id + 1; - root_port_t* rport = PIO_USB_ROOT_PORT(root_id); + root_port_t *rport = PIO_USB_ROOT_PORT(root_id); uint32_t const ints = rport->ints; - if ( ints & PIO_USB_INTS_CONNECT_BITS ) - { + if ( ints & PIO_USB_INTS_CONNECT_BITS ) { hcd_event_device_attach(tu_rhport, true); } - if ( ints & PIO_USB_INTS_DISCONNECT_BITS ) - { + if ( ints & PIO_USB_INTS_DISCONNECT_BITS ) { hcd_event_device_remove(tu_rhport, true); } - if ( ints & PIO_USB_INTS_ENDPOINT_COMPLETE_BITS ) - { + if ( ints & PIO_USB_INTS_ENDPOINT_COMPLETE_BITS ) { handle_endpoint_irq(rport, XFER_RESULT_SUCCESS, &rport->ep_complete); } - if ( ints & PIO_USB_INTS_ENDPOINT_STALLED_BITS ) - { + if ( ints & PIO_USB_INTS_ENDPOINT_STALLED_BITS ) { handle_endpoint_irq(rport, XFER_RESULT_STALLED, &rport->ep_stalled); } - if ( ints & PIO_USB_INTS_ENDPOINT_ERROR_BITS ) - { + if ( ints & PIO_USB_INTS_ENDPOINT_ERROR_BITS ) { handle_endpoint_irq(rport, XFER_RESULT_FAILED, &rport->ep_error); } -- cgit v1.3.1 From b8b01c10758043d318716569e693912f3e02c75b Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 8 Aug 2023 21:59:36 +0700 Subject: update to dcd ip3511 to add work-around for lpc54628 usb hs errata USB.1 and USB.2 msc is mounted, but device couldn't work reliably and got constant reset due to other errata probably. --- .idea/cmake.xml | 4 +- hw/bsp/lpc54/family.c | 6 +- hw/bsp/lpc54/family.cmake | 1 + src/common/tusb_common.h | 5 +- src/common/tusb_mcu.h | 8 +- src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c | 266 ++++++++++++++++----------- 6 files changed, 170 insertions(+), 120 deletions(-) (limited to 'src/portable') diff --git a/.idea/cmake.xml b/.idea/cmake.xml index 76143ba10..4a69d02cf 100644 --- a/.idea/cmake.xml +++ b/.idea/cmake.xml @@ -30,7 +30,8 @@ - + + @@ -51,6 +52,7 @@ + \ No newline at end of file diff --git a/hw/bsp/lpc54/family.c b/hw/bsp/lpc54/family.c index 108a7d783..7411c72d4 100644 --- a/hw/bsp/lpc54/family.c +++ b/hw/bsp/lpc54/family.c @@ -70,13 +70,11 @@ //--------------------------------------------------------------------+ // Forward USB interrupt events to TinyUSB IRQ Handler //--------------------------------------------------------------------+ -void USB0_IRQHandler(void) -{ +void USB0_IRQHandler(void) { tud_int_handler(0); } -void USB1_IRQHandler(void) -{ +void USB1_IRQHandler(void) { tud_int_handler(1); } diff --git a/hw/bsp/lpc54/family.cmake b/hw/bsp/lpc54/family.cmake index 0512fe31f..b016441c1 100644 --- a/hw/bsp/lpc54/family.cmake +++ b/hw/bsp/lpc54/family.cmake @@ -59,6 +59,7 @@ function(add_board_target BOARD_TARGET) BOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED BOARD_TUH_MAX_SPEED=OPT_MODE_HIGH_SPEED CFG_TUH_MEM_SECTION=__attribute__\(\(section\(\"m_usb_global\"\)\)\) + #CFG_TUD_MEM_SECTION=__attribute__\(\(section\(\"m_usb_global\"\)\)\) ) endif () diff --git a/src/common/tusb_common.h b/src/common/tusb_common.h index 25f85e501..c303c6eaf 100644 --- a/src/common/tusb_common.h +++ b/src/common/tusb_common.h @@ -159,11 +159,12 @@ TU_ATTR_ALWAYS_INLINE static inline uint16_t tu_max16 (uint16_t x, uint16_t y) { TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_max32 (uint32_t x, uint32_t y) { return (x > y) ? x : y; } //------------- Align -------------// -TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_align(uint32_t value, uint32_t alignment) -{ +TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_align(uint32_t value, uint32_t alignment) { return value & ((uint32_t) ~(alignment-1)); } +TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_align4 (uint32_t value) { return (value & 0xFFFFFFFCUL); } +TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_align8 (uint32_t value) { return (value & 0xFFFFFFF8UL); } TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_align16 (uint32_t value) { return (value & 0xFFFFFFF0UL); } TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_align32 (uint32_t value) { return (value & 0xFFFFFFE0UL); } TU_ATTR_ALWAYS_INLINE static inline uint32_t tu_align4k (uint32_t value) { return (value & 0xFFFFF000UL); } diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 89f89182e..35f94efbc 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -58,6 +58,7 @@ // NXP //--------------------------------------------------------------------+ #if TU_CHECK_MCU(OPT_MCU_LPC11UXX, OPT_MCU_LPC13XX, OPT_MCU_LPC15XX) + #define TUP_USBIP_IP3511 #define TUP_DCD_ENDPOINT_MAX 5 #elif TU_CHECK_MCU(OPT_MCU_LPC175X_6X, OPT_MCU_LPC177X_8X, OPT_MCU_LPC40XX) @@ -66,14 +67,17 @@ #define TUP_OHCI_RHPORTS 2 #elif TU_CHECK_MCU(OPT_MCU_LPC51UXX) + #define TUP_USBIP_IP3511 #define TUP_DCD_ENDPOINT_MAX 5 -#elif TU_CHECK_MCU(OPT_MCU_LPC54XXX) +#elif TU_CHECK_MCU(OPT_MCU_LPC54) // TODO USB0 has 5, USB1 has 6 + #define TUP_USBIP_IP3511 #define TUP_DCD_ENDPOINT_MAX 6 -#elif TU_CHECK_MCU(OPT_MCU_LPC55XX) +#elif TU_CHECK_MCU(OPT_MCU_LPC55) // TODO USB0 has 5, USB1 has 6 + #define TUP_USBIP_IP3511 #define TUP_DCD_ENDPOINT_MAX 6 #elif TU_CHECK_MCU(OPT_MCU_LPC18XX, OPT_MCU_LPC43XX) diff --git a/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c b/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c index 7ca698a93..f4ed09d83 100644 --- a/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c +++ b/src/portable/nxp/lpc_ip3511/dcd_lpc_ip3511.c @@ -34,18 +34,13 @@ * - LPC54114 * - LPC55s69 */ -#if CFG_TUD_ENABLED && ( CFG_TUSB_MCU == OPT_MCU_LPC11UXX || \ - CFG_TUSB_MCU == OPT_MCU_LPC13XX || \ - CFG_TUSB_MCU == OPT_MCU_LPC15XX || \ - CFG_TUSB_MCU == OPT_MCU_LPC51UXX || \ - CFG_TUSB_MCU == OPT_MCU_LPC54XXX || \ - CFG_TUSB_MCU == OPT_MCU_LPC55XX) +#if CFG_TUD_ENABLED && defined(TUP_USBIP_IP3511) //--------------------------------------------------------------------+ // INCLUDE //--------------------------------------------------------------------+ -#if CFG_TUSB_MCU == OPT_MCU_LPC11UXX || CFG_TUSB_MCU == OPT_MCU_LPC13XX || CFG_TUSB_MCU == OPT_MCU_LPC15XX +#if TU_CHECK_MCU(OPT_MCU_LPC11UXX, OPT_MCU_LPC13XX, OPT_MCU_LPC15XX) // LPCOpen #include "chip.h" #else @@ -80,7 +75,7 @@ typedef struct { enum { NBYTES_ISO_FS_MAX = 1023, // FS ISO NBYTES_ISO_HS_MAX = 1024, // HS ISO - NBYTES_CBI_FS_MAX = 64, // FS control/bulk/interrupt + NBYTES_CBI_FS_MAX = 64, // FS control/bulk/interrupt. TODO some FS can do burst with higher size e.g 1024. Need to test NBYTES_CBI_HS_MAX = 32767 // can be up to all 15-bit, but only tested with 4096 }; @@ -90,26 +85,36 @@ enum { }; enum { - CMDSTAT_DEVICE_ADDR_MASK = TU_BIT(7 )-1, - CMDSTAT_DEVICE_ENABLE_MASK = TU_BIT(7 ), - CMDSTAT_SETUP_RECEIVED_MASK = TU_BIT(8 ), - CMDSTAT_DEVICE_CONNECT_MASK = TU_BIT(16), // reflect the soft-connect only, does not reflect the actual attached state - CMDSTAT_DEVICE_SUSPEND_MASK = TU_BIT(17), - // 23-22 is link speed (only available for HighSpeed port) - CMDSTAT_CONNECT_CHANGE_MASK = TU_BIT(24), - CMDSTAT_SUSPEND_CHANGE_MASK = TU_BIT(25), - CMDSTAT_RESET_CHANGE_MASK = TU_BIT(26), - CMDSTAT_VBUS_DEBOUNCED_MASK = TU_BIT(28), + DEVCMDSTAT_DEVICE_ADDR_MASK = TU_BIT(7 )-1, + DEVCMDSTAT_DEVICE_ENABLE_MASK = TU_BIT(7 ), + DEVCMDSTAT_SETUP_RECEIVED_MASK = TU_BIT(8 ), + DEVCMDSTAT_DEVICE_CONNECT_MASK = TU_BIT(16), // reflect the soft-connect only, does not reflect the actual attached state + DEVCMDSTAT_DEVICE_SUSPEND_MASK = TU_BIT(17), + // 23-22 is link speed (only available for HighSpeed port) + DEVCMDSTAT_CONNECT_CHANGE_MASK = TU_BIT(24), + DEVCMDSTAT_SUSPEND_CHANGE_MASK = TU_BIT(25), + DEVCMDSTAT_RESET_CHANGE_MASK = TU_BIT(26), + DEVCMDSTAT_VBUS_DEBOUNCED_MASK = TU_BIT(28), }; enum { - CMDSTAT_SPEED_SHIFT = 22 + DEVCMDSTAT_SPEED_SHIFT = 22 }; //--------------------------------------------------------------------+ // Endpoint Command/Status List //--------------------------------------------------------------------+ +// EP Command/Status field definition +enum { + EPCS_TYPE = TU_BIT(26), + EPCS_RF_TV = TU_BIT(27), + EPCS_TOGGLE_RESET = TU_BIT(28), + EPCS_STALL = TU_BIT(29), + EPCS_DISABLED = TU_BIT(30), + EPCS_ACTIVE = TU_BIT(31), +}; + // Endpoint Command/Status typedef union TU_ATTR_PACKED { @@ -133,8 +138,8 @@ typedef union TU_ATTR_PACKED volatile struct { uint32_t TU_RESERVED : 26; - uint32_t is_iso : 1 ; - uint32_t toggle_mode : 1 ; + uint32_t type : 1 ; + uint32_t rf_tv : 1 ; // rate feedback or toggle value uint32_t toggle_reset : 1 ; uint32_t stall : 1 ; uint32_t disable : 1 ; @@ -180,6 +185,7 @@ typedef struct CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(256) static dcd_data_t _dcd; // Dummy buffer to fix ZLPs overwriting the buffer (probably an USB/DMA controller bug) +// TODO find way to save memory CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(64) static uint8_t dummy[8]; //--------------------------------------------------------------------+ @@ -188,59 +194,73 @@ CFG_TUD_MEM_SECTION TU_ATTR_ALIGNED(64) static uint8_t dummy[8]; typedef struct { - dcd_registers_t* regs; // registers - const tusb_speed_t max_speed; // max link speed - const IRQn_Type irqnum; // IRQ number - const uint8_t ep_pairs; // Max bi-directional Endpoints + dcd_registers_t* regs; // registers + const bool is_highspeed; // max link speed + const IRQn_Type irqnum; // IRQ number + const uint8_t ep_pairs; // Max bi-directional Endpoints }dcd_controller_t; #ifdef INCLUDE_FSL_DEVICE_REGISTERS -static const dcd_controller_t _dcd_controller[] = -{ - { .regs = (dcd_registers_t*) USB0_BASE , .max_speed = TUSB_SPEED_FULL, .irqnum = USB0_IRQn, .ep_pairs = FSL_FEATURE_USB_EP_NUM }, +static const dcd_controller_t _dcd_controller[] = { + { .regs = (dcd_registers_t*) USB0_BASE , .is_highspeed = false, .irqnum = USB0_IRQn, .ep_pairs = FSL_FEATURE_USB_EP_NUM }, #if defined(FSL_FEATURE_SOC_USBHSD_COUNT) && FSL_FEATURE_SOC_USBHSD_COUNT - { .regs = (dcd_registers_t*) USBHSD_BASE, .max_speed = TUSB_SPEED_HIGH, .irqnum = USB1_IRQn, .ep_pairs = FSL_FEATURE_USBHSD_EP_NUM } + { .regs = (dcd_registers_t*) USBHSD_BASE, .is_highspeed = true, .irqnum = USB1_IRQn, .ep_pairs = FSL_FEATURE_USBHSD_EP_NUM } #endif }; #else -static const dcd_controller_t _dcd_controller[] = -{ - { .regs = (dcd_registers_t*) LPC_USB0_BASE, .max_speed = TUSB_SPEED_FULL, .irqnum = USB0_IRQn, .ep_pairs = 5 }, +static const dcd_controller_t _dcd_controller[] = { + { .regs = (dcd_registers_t*) LPC_USB0_BASE, .is_highspeed = false, .irqnum = USB0_IRQn, .ep_pairs = 5 }, }; #endif +#if defined(FSL_FEATURE_SOC_USBHSD_COUNT) && FSL_FEATURE_SOC_USBHSD_COUNT + #define IP3511_HAS_HIGHSPEED +#endif + //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -static inline uint16_t get_buf_offset(void const * buffer) -{ +TU_ATTR_ALWAYS_INLINE static inline uint16_t get_buf_offset(void const * buffer) { uint32_t addr = (uint32_t) buffer; TU_ASSERT( (addr & 0x3f) == 0, 0 ); return ( (addr >> 6) & 0xFFFFUL ) ; } -static inline uint8_t ep_addr2id(uint8_t ep_addr) -{ +TU_ATTR_ALWAYS_INLINE static inline uint8_t ep_addr2id(uint8_t ep_addr) { return 2*(ep_addr & 0x0F) + ((ep_addr & TUSB_DIR_IN_MASK) ? 1 : 0); } +TU_ATTR_ALWAYS_INLINE static inline bool ep_is_iso(ep_cmd_sts_t* ep_cs, bool is_highspeed) { + return is_highspeed ? (ep_cs[0].cmd_sts.type && !ep_cs[0].cmd_sts.rf_tv) : ep_cs->cmd_sts.type; +} + +TU_ATTR_ALWAYS_INLINE static inline bool ep_is_bulk(ep_cmd_sts_t* ep_cs) { + return (ep_cs[0].cmd_sts.type == 0) && (ep_cs[0].cmd_sts.rf_tv == 0); +} + +TU_ATTR_ALWAYS_INLINE static inline ep_cmd_sts_t* get_ep_cs(uint8_t ep_id) { + return _dcd.ep[ep_id]; +} + +TU_ATTR_ALWAYS_INLINE static inline bool rhport_is_highspeed(uint8_t rhport) { + return _dcd_controller[rhport].is_highspeed; +} + //--------------------------------------------------------------------+ // CONTROLLER API //--------------------------------------------------------------------+ -static void prepare_setup_packet(uint8_t rhport) -{ - if (_dcd_controller[rhport].max_speed == TUSB_SPEED_FULL ) - { - _dcd.ep[0][1].buffer_fs.offset = get_buf_offset(_dcd.setup_packet); - }else - { - _dcd.ep[0][1].buffer_hs.offset = get_buf_offset(_dcd.setup_packet); +static void prepare_setup_packet(uint8_t rhport) { + uint16_t const buf_offset = get_buf_offset(_dcd.setup_packet); + if ( _dcd_controller[rhport].is_highspeed ) { + _dcd.ep[0][1].buffer_hs.offset = buf_offset; + } else { + _dcd.ep[0][1].buffer_fs.offset = buf_offset; } } @@ -268,8 +288,8 @@ void dcd_init(uint8_t rhport) dcd_reg->DATABUFSTART = tu_align((uint32_t) &_dcd, TU_BIT(22)); // 22-bit alignment dcd_reg->INTSTAT |= dcd_reg->INTSTAT; // clear all pending interrupt dcd_reg->INTEN = INT_DEVICE_STATUS_MASK; - dcd_reg->DEVCMDSTAT |= CMDSTAT_DEVICE_ENABLE_MASK | CMDSTAT_DEVICE_CONNECT_MASK | - CMDSTAT_RESET_CHANGE_MASK | CMDSTAT_CONNECT_CHANGE_MASK | CMDSTAT_SUSPEND_CHANGE_MASK; + dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_DEVICE_ENABLE_MASK | DEVCMDSTAT_DEVICE_CONNECT_MASK | + DEVCMDSTAT_RESET_CHANGE_MASK | DEVCMDSTAT_CONNECT_CHANGE_MASK | DEVCMDSTAT_SUSPEND_CHANGE_MASK; NVIC_ClearPendingIRQ(_dcd_controller[rhport].irqnum); } @@ -291,7 +311,7 @@ void dcd_set_address(uint8_t rhport, uint8_t dev_addr) // Response with status first before changing device address dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_IN), NULL, 0); - dcd_reg->DEVCMDSTAT &= ~CMDSTAT_DEVICE_ADDR_MASK; + dcd_reg->DEVCMDSTAT &= ~DEVCMDSTAT_DEVICE_ADDR_MASK; dcd_reg->DEVCMDSTAT |= dev_addr; } @@ -303,13 +323,13 @@ void dcd_remote_wakeup(uint8_t rhport) void dcd_connect(uint8_t rhport) { dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->DEVCMDSTAT |= CMDSTAT_DEVICE_CONNECT_MASK; + dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_DEVICE_CONNECT_MASK; } void dcd_disconnect(uint8_t rhport) { dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; - dcd_reg->DEVCMDSTAT &= ~CMDSTAT_DEVICE_CONNECT_MASK; + dcd_reg->DEVCMDSTAT &= ~DEVCMDSTAT_DEVICE_CONNECT_MASK; } void dcd_sof_enable(uint8_t rhport, bool en) @@ -340,19 +360,39 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) _dcd.ep[ep_id][0].cmd_sts.stall = 0; _dcd.ep[ep_id][0].cmd_sts.toggle_reset = 1; - _dcd.ep[ep_id][0].cmd_sts.toggle_mode = 0; + _dcd.ep[ep_id][0].cmd_sts.rf_tv = 0; } bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) { //------------- Prepare Queue Head -------------// uint8_t ep_id = ep_addr2id(p_endpoint_desc->bEndpointAddress); + ep_cmd_sts_t* ep_cs = get_ep_cs(ep_id); // Check if endpoint is available - TU_ASSERT( _dcd.ep[ep_id][0].cmd_sts.disable && _dcd.ep[ep_id][1].cmd_sts.disable ); + TU_ASSERT( ep_cs[0].cmd_sts.disable && ep_cs[1].cmd_sts.disable ); edpt_reset(rhport, ep_id); - _dcd.ep[ep_id][0].cmd_sts.is_iso = (p_endpoint_desc->bmAttributes.xfer == TUSB_XFER_ISOCHRONOUS); + + switch (p_endpoint_desc->bmAttributes.xfer) { + case TUSB_XFER_ISOCHRONOUS: + ep_cs[0].cmd_sts.type = 1; + break; + + case TUSB_XFER_INTERRUPT: + // What is interrupt endpoint in rate feedback mode ? + if ( rhport_is_highspeed(rhport) ) { + ep_cs[0].cmd_sts.type = 1; + ep_cs[0].cmd_sts.rf_tv = 1; + } + break; + + case TUSB_XFER_BULK: + // nothing to do both type and rf_tv are 0 + break; + + default: break; + } // Enable EP interrupt dcd_registers_t* dcd_reg = _dcd_controller[rhport].regs; @@ -379,42 +419,50 @@ void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) _dcd.ep[ep_id][0].cmd_sts.disable = _dcd.ep[ep_id][1].cmd_sts.disable = 1; } -static void prepare_ep_xfer(uint8_t rhport, uint8_t ep_id, uint16_t buf_offset, uint16_t total_bytes) -{ +static void prepare_ep_xfer(uint8_t rhport, uint8_t ep_id, uint16_t buf_offset, uint16_t total_bytes) { uint16_t nbytes; - - if (_dcd_controller[rhport].max_speed == TUSB_SPEED_FULL ) - { - nbytes = tu_min16(total_bytes, _dcd.ep[ep_id][0].cmd_sts.is_iso ? NBYTES_ISO_FS_MAX : NBYTES_CBI_FS_MAX); - _dcd.ep[ep_id][0].buffer_fs.offset = buf_offset; - _dcd.ep[ep_id][0].buffer_fs.nbytes = nbytes; - }else - { - nbytes = tu_min16(total_bytes, NBYTES_CBI_HS_MAX); - _dcd.ep[ep_id][0].buffer_hs.offset = buf_offset; - _dcd.ep[ep_id][0].buffer_hs.nbytes = nbytes; + ep_cmd_sts_t* ep_cs = get_ep_cs(ep_id); + + const bool is_iso = ep_is_iso(ep_cs, _dcd_controller[rhport].is_highspeed); + + if ( rhport_is_highspeed(rhport) ) { + nbytes = tu_min16(total_bytes, is_iso ? NBYTES_ISO_HS_MAX : NBYTES_CBI_HS_MAX); + #if TU_CHECK_MCU(OPT_MCU_LPC54) + // LPC54 Errata USB.1: In USB high-speed device mode, the NBytes field does not decrement after BULK OUT transfer. + // Suggested Work-around: Program the NByte to the max packet size (512) + // Actual Work-around: round up NByte to multiple of 4. + // Note: this can cause buffer overflowed and corrupt data if host send more data than total_bytes + if ( (ep_id > 1) && (ep_id & 0x01) == 0 && ep_is_bulk(ep_cs) ) { + if ( nbytes & 0x03 ) { + nbytes = tu_align4(nbytes) + 4; + } + } + #endif + + ep_cs[0].buffer_hs.offset = buf_offset; + ep_cs[0].buffer_hs.nbytes = nbytes; + }else { + nbytes = tu_min16(total_bytes, is_iso ? NBYTES_ISO_FS_MAX : NBYTES_CBI_FS_MAX); + ep_cs[0].buffer_fs.offset = buf_offset; + ep_cs[0].buffer_fs.nbytes = nbytes; } _dcd.dma[ep_id].nbytes = nbytes; - - _dcd.ep[ep_id][0].cmd_sts.active = 1; + ep_cs[0].cmd_sts.active = 1; } -bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes) -{ +bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes) { uint8_t const ep_id = ep_addr2id(ep_addr); + if (!buffer || total_bytes == 0) { + // Although having no data, ZLPs can cause buffer overwritten to zeroes. Probably due to USB/DMA controller side + // effect/bug. Assigned buffer offset to (valid) dummy to prevent overwriting to DATABUFSTART + buffer = (uint8_t *) (uint32_t) dummy; + } + tu_memclr(&_dcd.dma[ep_id], sizeof(xfer_dma_t)); _dcd.dma[ep_id].total_bytes = total_bytes; - if (!buffer) - { - // Although having no data, ZLPs can cause buffer overwritten to zeroes. - // Probably due to USB/DMA controller side effect/bug. - // Assigned buffer offset to (valid) dummy to prevent overwriting to DATABUFSTART - buffer = (uint8_t*)(uint32_t)dummy; - } - prepare_ep_xfer(rhport, ep_id, get_buf_offset(buffer), total_bytes); return true; @@ -441,23 +489,19 @@ static void bus_reset(uint8_t rhport) dcd_reg->EPSKIP = 0xFFFFFFFF; dcd_reg->INTSTAT = dcd_reg->INTSTAT; // clear all pending interrupt - dcd_reg->DEVCMDSTAT |= CMDSTAT_SETUP_RECEIVED_MASK; // clear setup received interrupt + dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_SETUP_RECEIVED_MASK; // clear setup received interrupt dcd_reg->INTEN = INT_DEVICE_STATUS_MASK | TU_BIT(0) | TU_BIT(1); // enable device status & control endpoints } -static void process_xfer_isr(uint8_t rhport, uint32_t int_status) -{ +static void process_xfer_isr(uint8_t rhport, uint32_t int_status) { uint8_t const max_ep = 2*_dcd_controller[rhport].ep_pairs; - for(uint8_t ep_id = 0; ep_id < max_ep; ep_id++ ) - { - if ( tu_bit_test(int_status, ep_id) ) - { + for(uint8_t ep_id = 0; ep_id < max_ep; ep_id++ ) { + if ( tu_bit_test(int_status, ep_id) ) { ep_cmd_sts_t * ep_cs = &_dcd.ep[ep_id][0]; xfer_dma_t* xfer_dma = &_dcd.dma[ep_id]; - if ( ep_id == 0 || ep_id == 1) - { + if ( ep_id <= 1 ) { // For control endpoint, we need to manually clear Active bit ep_cs->cmd_sts.active = 0; } @@ -465,26 +509,29 @@ static void process_xfer_isr(uint8_t rhport, uint32_t int_status) uint16_t buf_offset; uint16_t buf_nbytes; - if (_dcd_controller[rhport].max_speed == TUSB_SPEED_FULL) - { - buf_offset = ep_cs->buffer_fs.offset; - buf_nbytes = ep_cs->buffer_fs.nbytes; - }else - { + if ( rhport_is_highspeed(rhport) ) { buf_offset = ep_cs->buffer_hs.offset; buf_nbytes = ep_cs->buffer_hs.nbytes; + + #if TU_CHECK_MCU(OPT_MCU_LPC54) + // LPC54 Errata USB.2: In USB high-speed device mode, the NBytes field is not correct after BULK IN transfer + // There is no work-around. For EP in transfer, the NByte value can be ignored after a packet is transmitted. + if ( (ep_id > 1) && (ep_id & 0x01) == 1 && ep_is_bulk(ep_cs) ) { + buf_nbytes = 0; + } + #endif + } else { + buf_offset = ep_cs->buffer_fs.offset; + buf_nbytes = ep_cs->buffer_fs.nbytes; } xfer_dma->xferred_bytes += xfer_dma->nbytes - buf_nbytes; - if ( (buf_nbytes == 0) && (xfer_dma->total_bytes > xfer_dma->xferred_bytes) ) - { + if ( (buf_nbytes == 0) && (xfer_dma->total_bytes > xfer_dma->xferred_bytes) ) { // There is more data to transfer // buff_offset has been already increased by hw to correct value for next transfer prepare_ep_xfer(rhport, ep_id, buf_offset, xfer_dma->total_bytes - xfer_dma->xferred_bytes); - } - else - { + } else { // for detecting ZLP xfer_dma->total_bytes = xfer_dma->xferred_bytes; @@ -511,19 +558,16 @@ void dcd_int_handler(uint8_t rhport) //------------- Device Status -------------// if ( int_status & INT_DEVICE_STATUS_MASK ) { - dcd_reg->DEVCMDSTAT |= CMDSTAT_RESET_CHANGE_MASK | CMDSTAT_CONNECT_CHANGE_MASK | CMDSTAT_SUSPEND_CHANGE_MASK; + dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_RESET_CHANGE_MASK | DEVCMDSTAT_CONNECT_CHANGE_MASK | DEVCMDSTAT_SUSPEND_CHANGE_MASK; - if ( cmd_stat & CMDSTAT_RESET_CHANGE_MASK) // bus reset + if ( cmd_stat & DEVCMDSTAT_RESET_CHANGE_MASK) // bus reset { bus_reset(rhport); tusb_speed_t speed = TUSB_SPEED_FULL; - - if (_dcd_controller[rhport].max_speed == TUSB_SPEED_HIGH) - { + if ( _dcd_controller[rhport].is_highspeed ) { // 0 : reserved, 1 : full, 2 : high, 3: super - if ( 2 == ((cmd_stat >> CMDSTAT_SPEED_SHIFT) & 0x3UL) ) - { + if ( 2 == ((cmd_stat >> DEVCMDSTAT_SPEED_SHIFT) & 0x3UL) ) { speed= TUSB_SPEED_HIGH; } } @@ -531,35 +575,35 @@ void dcd_int_handler(uint8_t rhport) dcd_event_bus_reset(rhport, speed, true); } - if (cmd_stat & CMDSTAT_CONNECT_CHANGE_MASK) + if (cmd_stat & DEVCMDSTAT_CONNECT_CHANGE_MASK) { // device disconnect - if (cmd_stat & CMDSTAT_DEVICE_ADDR_MASK) + if (cmd_stat & DEVCMDSTAT_DEVICE_ADDR_MASK) { // debouncing as this can be set when device is powering dcd_event_bus_signal(rhport, DCD_EVENT_UNPLUGGED, true); } } - if (cmd_stat & CMDSTAT_SUSPEND_CHANGE_MASK) + if (cmd_stat & DEVCMDSTAT_SUSPEND_CHANGE_MASK) { // suspend signal, bus idle for more than 3ms // Note: Host may delay more than 3 ms before and/or after bus reset before doing enumeration. - if (cmd_stat & CMDSTAT_DEVICE_ADDR_MASK) + if (cmd_stat & DEVCMDSTAT_DEVICE_ADDR_MASK) { - dcd_event_bus_signal(rhport, (cmd_stat & CMDSTAT_DEVICE_SUSPEND_MASK) ? DCD_EVENT_SUSPEND : DCD_EVENT_RESUME, true); + dcd_event_bus_signal(rhport, (cmd_stat & DEVCMDSTAT_DEVICE_SUSPEND_MASK) ? DCD_EVENT_SUSPEND : DCD_EVENT_RESUME, true); } } } // Setup Receive - if ( tu_bit_test(int_status, 0) && (cmd_stat & CMDSTAT_SETUP_RECEIVED_MASK) ) + if ( tu_bit_test(int_status, 0) && (cmd_stat & DEVCMDSTAT_SETUP_RECEIVED_MASK) ) { // Follow UM flowchart to clear Active & Stall on both Control IN/OUT endpoints _dcd.ep[0][0].cmd_sts.active = _dcd.ep[1][0].cmd_sts.active = 0; _dcd.ep[0][0].cmd_sts.stall = _dcd.ep[1][0].cmd_sts.stall = 0; - dcd_reg->DEVCMDSTAT |= CMDSTAT_SETUP_RECEIVED_MASK; + dcd_reg->DEVCMDSTAT |= DEVCMDSTAT_SETUP_RECEIVED_MASK; dcd_event_setup_received(rhport, _dcd.setup_packet, true); -- cgit v1.3.1 From b3c7fe1023d14d1e07eb21ca9a61438bff49a788 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 15 Aug 2023 00:09:31 +0700 Subject: clear qhd halted bit if not caused by STALL protocol, allow for next transfer --- src/portable/ehci/ehci.c | 1 + 1 file changed, 1 insertion(+) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 79811985c..c5036b5a3 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -579,6 +579,7 @@ void qhd_xfer_complete_isr(ehci_qhd_t * qhd) { if (qtd_overlay->xact_err || qtd_overlay->err_count == 0 || qtd_overlay->buffer_err || qtd_overlay->babble_err) { // Error count = 0 often occurs when device disconnected, or other bus-related error xfer_result = XFER_RESULT_FAILED; + qtd_overlay->halted = false; // clear halted bit if it is not caused by STALL TU_LOG3(" QHD xfer err count: %d\n", qtd_overlay->err_count); // TU_BREAKPOINT(); // TODO skip unplugged device }else { -- cgit v1.3.1 From f4845e4e6cc2faca4e60cd83959850f27d3f3076 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 16 Aug 2023 14:43:58 +0700 Subject: minor comment --- src/portable/ehci/ehci.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index c5036b5a3..c93c33fc0 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -578,8 +578,9 @@ void qhd_xfer_complete_isr(ehci_qhd_t * qhd) { if ( qtd_overlay->halted ) { if (qtd_overlay->xact_err || qtd_overlay->err_count == 0 || qtd_overlay->buffer_err || qtd_overlay->babble_err) { // Error count = 0 often occurs when device disconnected, or other bus-related error + // clear halted bit if not caused by STALL to allow more transfer xfer_result = XFER_RESULT_FAILED; - qtd_overlay->halted = false; // clear halted bit if it is not caused by STALL + qtd_overlay->halted = false; TU_LOG3(" QHD xfer err count: %d\n", qtd_overlay->err_count); // TU_BREAKPOINT(); // TODO skip unplugged device }else { -- cgit v1.3.1 From 9257a0f562a1cb939a902e7c41de5032b0f7de19 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 18 Aug 2023 12:48:12 +0700 Subject: - update nrf52 bsp for cmake - add empty tuh_int_handler/tud_int_handler if corresponidng stack not enabled - add hcd_template.c --- hw/bsp/nrf/boards/adafruit_clue/board.cmake | 5 + hw/bsp/nrf/boards/arduino_nano33_ble/board.cmake | 5 + .../boards/circuitplayground_bluefruit/board.cmake | 5 + .../boards/feather_nrf52840_express/board.cmake | 6 + .../nrf/boards/feather_nrf52840_sense/board.cmake | 5 + hw/bsp/nrf/boards/itsybitsy_nrf52840/board.cmake | 5 + hw/bsp/nrf/boards/nrf52840_mdk_dongle/board.cmake | 5 + hw/bsp/nrf/boards/pca10056/board.cmake | 3 - hw/bsp/nrf/boards/pca10059/board.cmake | 5 + hw/bsp/nrf/boards/pca10095/board.cmake | 4 - hw/bsp/nrf/boards/pca10100/board.cmake | 5 + hw/bsp/nrf/boards/raytac_mdbt50q_rx/board.cmake | 5 + hw/bsp/nrf/family.cmake | 14 +- src/device/usbd.h | 6 +- src/host/hcd.h | 12 +- src/portable/template/dcd_template.c | 4 +- src/portable/template/hcd_template.c | 162 +++++++++++++++++++++ src/tusb.h | 9 +- 18 files changed, 241 insertions(+), 24 deletions(-) create mode 100644 hw/bsp/nrf/boards/adafruit_clue/board.cmake create mode 100644 hw/bsp/nrf/boards/arduino_nano33_ble/board.cmake create mode 100644 hw/bsp/nrf/boards/circuitplayground_bluefruit/board.cmake create mode 100644 hw/bsp/nrf/boards/feather_nrf52840_express/board.cmake create mode 100644 hw/bsp/nrf/boards/feather_nrf52840_sense/board.cmake create mode 100644 hw/bsp/nrf/boards/itsybitsy_nrf52840/board.cmake create mode 100644 hw/bsp/nrf/boards/nrf52840_mdk_dongle/board.cmake create mode 100644 hw/bsp/nrf/boards/pca10059/board.cmake create mode 100644 hw/bsp/nrf/boards/pca10100/board.cmake create mode 100644 hw/bsp/nrf/boards/raytac_mdbt50q_rx/board.cmake create mode 100644 src/portable/template/hcd_template.c (limited to 'src/portable') diff --git a/hw/bsp/nrf/boards/adafruit_clue/board.cmake b/hw/bsp/nrf/boards/adafruit_clue/board.cmake new file mode 100644 index 000000000..eb97e5c55 --- /dev/null +++ b/hw/bsp/nrf/boards/adafruit_clue/board.cmake @@ -0,0 +1,5 @@ +set(MCU_VARIANT nrf52840) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/../../linker/nrf52840_s140_v6.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/boards/arduino_nano33_ble/board.cmake b/hw/bsp/nrf/boards/arduino_nano33_ble/board.cmake new file mode 100644 index 000000000..93647063a --- /dev/null +++ b/hw/bsp/nrf/boards/arduino_nano33_ble/board.cmake @@ -0,0 +1,5 @@ +set(MCU_VARIANT nrf52840) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/arduino_nano33_ble.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/boards/circuitplayground_bluefruit/board.cmake b/hw/bsp/nrf/boards/circuitplayground_bluefruit/board.cmake new file mode 100644 index 000000000..eb97e5c55 --- /dev/null +++ b/hw/bsp/nrf/boards/circuitplayground_bluefruit/board.cmake @@ -0,0 +1,5 @@ +set(MCU_VARIANT nrf52840) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/../../linker/nrf52840_s140_v6.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/boards/feather_nrf52840_express/board.cmake b/hw/bsp/nrf/boards/feather_nrf52840_express/board.cmake new file mode 100644 index 000000000..0acbecf7a --- /dev/null +++ b/hw/bsp/nrf/boards/feather_nrf52840_express/board.cmake @@ -0,0 +1,6 @@ +set(MCU_VARIANT nrf52840) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/../../linker/nrf52840_s140_v6.ld) +# set(LD_FILE_GNU ${NRFX_DIR}/mdk/nrf52840_xxaa.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/boards/feather_nrf52840_sense/board.cmake b/hw/bsp/nrf/boards/feather_nrf52840_sense/board.cmake new file mode 100644 index 000000000..eb97e5c55 --- /dev/null +++ b/hw/bsp/nrf/boards/feather_nrf52840_sense/board.cmake @@ -0,0 +1,5 @@ +set(MCU_VARIANT nrf52840) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/../../linker/nrf52840_s140_v6.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/boards/itsybitsy_nrf52840/board.cmake b/hw/bsp/nrf/boards/itsybitsy_nrf52840/board.cmake new file mode 100644 index 000000000..eb97e5c55 --- /dev/null +++ b/hw/bsp/nrf/boards/itsybitsy_nrf52840/board.cmake @@ -0,0 +1,5 @@ +set(MCU_VARIANT nrf52840) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/../../linker/nrf52840_s140_v6.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/boards/nrf52840_mdk_dongle/board.cmake b/hw/bsp/nrf/boards/nrf52840_mdk_dongle/board.cmake new file mode 100644 index 000000000..ffa5932c1 --- /dev/null +++ b/hw/bsp/nrf/boards/nrf52840_mdk_dongle/board.cmake @@ -0,0 +1,5 @@ +set(MCU_VARIANT nrf52840) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/nrf52840_mdk_dongle.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/boards/pca10056/board.cmake b/hw/bsp/nrf/boards/pca10056/board.cmake index b4fe39fc0..693d7beed 100644 --- a/hw/bsp/nrf/boards/pca10056/board.cmake +++ b/hw/bsp/nrf/boards/pca10056/board.cmake @@ -2,7 +2,4 @@ set(MCU_VARIANT nrf52840) set(LD_FILE_GNU ${NRFX_DIR}/mdk/nrf52840_xxaa.ld) function(update_board TARGET) - target_compile_definitions(${TARGET} PUBLIC - NRF52840_XXAA - ) endfunction() diff --git a/hw/bsp/nrf/boards/pca10059/board.cmake b/hw/bsp/nrf/boards/pca10059/board.cmake new file mode 100644 index 000000000..c79eb5964 --- /dev/null +++ b/hw/bsp/nrf/boards/pca10059/board.cmake @@ -0,0 +1,5 @@ +set(MCU_VARIANT nrf52840) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/pca10059.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/boards/pca10095/board.cmake b/hw/bsp/nrf/boards/pca10095/board.cmake index 1e72243c9..ca5399a3a 100644 --- a/hw/bsp/nrf/boards/pca10095/board.cmake +++ b/hw/bsp/nrf/boards/pca10095/board.cmake @@ -2,10 +2,6 @@ set(MCU_VARIANT nrf5340_application) set(LD_FILE_GNU ${NRFX_DIR}/mdk/nrf5340_xxaa_application.ld) function(update_board TARGET) - target_compile_definitions(${TARGET} PUBLIC - NRF5340_XXAA - NRF5340_XXAA_APPLICATION - ) target_sources(${TARGET} PRIVATE ${NRFX_DIR}/drivers/src/nrfx_usbreg.c ) diff --git a/hw/bsp/nrf/boards/pca10100/board.cmake b/hw/bsp/nrf/boards/pca10100/board.cmake new file mode 100644 index 000000000..c30026815 --- /dev/null +++ b/hw/bsp/nrf/boards/pca10100/board.cmake @@ -0,0 +1,5 @@ +set(MCU_VARIANT nrf52833) +set(LD_FILE_GNU ${NRFX_DIR}/mdk/nrf52833_xxaa.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/boards/raytac_mdbt50q_rx/board.cmake b/hw/bsp/nrf/boards/raytac_mdbt50q_rx/board.cmake new file mode 100644 index 000000000..693d7beed --- /dev/null +++ b/hw/bsp/nrf/boards/raytac_mdbt50q_rx/board.cmake @@ -0,0 +1,5 @@ +set(MCU_VARIANT nrf52840) +set(LD_FILE_GNU ${NRFX_DIR}/mdk/nrf52840_xxaa.ld) + +function(update_board TARGET) +endfunction() diff --git a/hw/bsp/nrf/family.cmake b/hw/bsp/nrf/family.cmake index 2b13249f4..6c24d3658 100644 --- a/hw/bsp/nrf/family.cmake +++ b/hw/bsp/nrf/family.cmake @@ -33,13 +33,20 @@ function(add_board_target BOARD_TARGET) add_library(${BOARD_TARGET} STATIC # driver ${NRFX_DIR}/drivers/src/nrfx_power.c + ${NRFX_DIR}/drivers/src/nrfx_spim.c ${NRFX_DIR}/drivers/src/nrfx_uarte.c # mcu ${NRFX_DIR}/mdk/system_${MCU_VARIANT}.c ) - target_compile_definitions(${BOARD_TARGET} PUBLIC - CONFIG_GPIO_AS_PINRESET - ) + target_compile_definitions(${BOARD_TARGET} PUBLIC CONFIG_GPIO_AS_PINRESET) + + if (MCU_VARIANT STREQUAL "nrf52840") + target_compile_definitions(${BOARD_TARGET} PUBLIC NRF52840_XXAA) + elseif (MCU_VARIANT STREQUAL "nrf52833") + target_compile_definitions(${BOARD_TARGET} PUBLIC NRF52833_XXAA) + elseif (MCU_VARIANT STREQUAL "nrf5340_application") + target_compile_definitions(${BOARD_TARGET} PUBLIC NRF5340_XXAA NRF5340_XXAA_APPLICATION) + endif () if (TRACE_ETM STREQUAL "1") # ENABLE_TRACE will cause system_nrf5x.c to set up ETM trace @@ -115,6 +122,7 @@ function(family_configure_example TARGET RTOS) family_add_tinyusb(${TARGET} OPT_MCU_NRF5X ${RTOS}) target_sources(${TARGET}-tinyusb PUBLIC ${TOP}/src/portable/nordic/nrf5x/dcd_nrf5x.c + #${TOP}/src/portable/analog/max3421e/hcd_max3421e.c ) target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) diff --git a/src/device/usbd.h b/src/device/usbd.h index b11c1a09d..782f538fd 100644 --- a/src/device/usbd.h +++ b/src/device/usbd.h @@ -50,8 +50,7 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr); // Task function should be called in main/rtos loop TU_ATTR_ALWAYS_INLINE static inline -void tud_task (void) -{ +void tud_task (void) { tud_task_ext(UINT32_MAX, false); } @@ -80,8 +79,7 @@ bool tud_suspended(void); // Check if device is ready to transfer TU_ATTR_ALWAYS_INLINE static inline -bool tud_ready(void) -{ +bool tud_ready(void) { return tud_mounted() && !tud_suspended(); } diff --git a/src/host/hcd.h b/src/host/hcd.h index 9bcc1c6df..1b5038ef4 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -198,8 +198,7 @@ extern void hcd_event_handler(hcd_event_t const* event, bool in_isr); // Helper to send device attach event TU_ATTR_ALWAYS_INLINE static inline -void hcd_event_device_attach(uint8_t rhport, bool in_isr) -{ +void hcd_event_device_attach(uint8_t rhport, bool in_isr) { hcd_event_t event; event.rhport = rhport; event.event_id = HCD_EVENT_DEVICE_ATTACH; @@ -211,8 +210,7 @@ void hcd_event_device_attach(uint8_t rhport, bool in_isr) // Helper to send device removal event TU_ATTR_ALWAYS_INLINE static inline -void hcd_event_device_remove(uint8_t rhport, bool in_isr) -{ +void hcd_event_device_remove(uint8_t rhport, bool in_isr) { hcd_event_t event; event.rhport = rhport; event.event_id = HCD_EVENT_DEVICE_REMOVE; @@ -224,10 +222,8 @@ void hcd_event_device_remove(uint8_t rhport, bool in_isr) // Helper to send USB transfer event TU_ATTR_ALWAYS_INLINE static inline -void hcd_event_xfer_complete(uint8_t dev_addr, uint8_t ep_addr, uint32_t xferred_bytes, xfer_result_t result, bool in_isr) -{ - hcd_event_t event = - { +void hcd_event_xfer_complete(uint8_t dev_addr, uint8_t ep_addr, uint32_t xferred_bytes, xfer_result_t result, bool in_isr) { + hcd_event_t event = { .rhport = 0, // TODO correct rhport .event_id = HCD_EVENT_XFER_COMPLETE, .dev_addr = dev_addr, diff --git a/src/portable/template/dcd_template.c b/src/portable/template/dcd_template.c index 590dd9fcf..12d610bd6 100644 --- a/src/portable/template/dcd_template.c +++ b/src/portable/template/dcd_template.c @@ -26,7 +26,7 @@ #include "tusb_option.h" -#if CFG_TUSB_MCU == OPT_MCU_NONE +#if CFG_TUD_ENABLED && CFG_TUSB_MCU == OPT_MCU_NONE #include "device/dcd.h" @@ -141,4 +141,6 @@ void dcd_edpt_clear_stall (uint8_t rhport, uint8_t ep_addr) (void) ep_addr; } + + #endif diff --git a/src/portable/template/hcd_template.c b/src/portable/template/hcd_template.c new file mode 100644 index 000000000..3e3b91558 --- /dev/null +++ b/src/portable/template/hcd_template.c @@ -0,0 +1,162 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "tusb_option.h" + +#if CFG_TUH_ENABLED && CFG_TUSB_MCU == OPT_MCU_NONE + +#include "host/hcd.h" + +//--------------------------------------------------------------------+ +// Controller API +//--------------------------------------------------------------------+ + +// optional hcd configuration, called by tuh_configure() +bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { + (void) rhport; + (void) cfg_id; + (void) cfg_param; + + return false; +} + +// Initialize controller to host mode +bool hcd_init(uint8_t rhport) { + (void) rhport; + + return false; +} + +// Interrupt Handler +void hcd_int_handler(uint8_t rhport) { + (void) rhport; +} + +// Enable USB interrupt +void hcd_int_enable (uint8_t rhport) { + (void) rhport; +} + +// Disable USB interrupt +void hcd_int_disable(uint8_t rhport) { + (void) rhport; +} + +// Get frame number (1ms) +uint32_t hcd_frame_number(uint8_t rhport) { + (void) rhport; + + return 0; +} + +//--------------------------------------------------------------------+ +// Port API +//--------------------------------------------------------------------+ + +// Get the current connect status of roothub port +bool hcd_port_connect_status(uint8_t rhport) { + (void) rhport; + + return false; +} + +// Reset USB bus on the port. Return immediately, bus reset sequence may not be complete. +// Some port would require hcd_port_reset_end() to be invoked after 10ms to complete the reset sequence. +void hcd_port_reset(uint8_t rhport) { + (void) rhport; +} + +// Complete bus reset sequence, may be required by some controllers +void hcd_port_reset_end(uint8_t rhport) { + (void) rhport; +} + +// Get port link speed +tusb_speed_t hcd_port_speed_get(uint8_t rhport) { + (void) rhport; + + return TUSB_SPEED_FULL; +} + +// HCD closes all opened endpoints belong to this device +void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { + (void) rhport; + (void) dev_addr; +} + +//--------------------------------------------------------------------+ +// Endpoints API +//--------------------------------------------------------------------+ + +// Open an endpoint +bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc) { + (void) rhport; + (void) dev_addr; + (void) ep_desc; + + return false; +} + +// Submit a transfer, when complete hcd_event_xfer_complete() must be invoked +bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + (void) buffer; + (void) buflen; + + return false; +} + +// Abort a queued transfer. Note: it can only abort transfer that has not been started +// Return true if a queued transfer is aborted, false if there is no transfer to abort +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + + return false; +} + +// Submit a special transfer to send 8-byte Setup Packet, when complete hcd_event_xfer_complete() must be invoked +bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { + (void) rhport; + (void) dev_addr; + (void) setup_packet; + + return false; +} + +// clear stall, data toggle is also reset to DATA0 +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + + return false; +} + +#endif diff --git a/src/tusb.h b/src/tusb.h index 37a521fa8..d6534ca28 100644 --- a/src/tusb.h +++ b/src/tusb.h @@ -64,7 +64,10 @@ #if CFG_TUH_VENDOR #include "class/vendor/vendor_host.h" #endif - +#else + #ifndef tuh_int_handler + #define tuh_int_handler(_x) + #endif #endif //------------- DEVICE -------------// @@ -118,6 +121,10 @@ #if CFG_TUD_BTH #include "class/bth/bth_device.h" #endif +#else + #ifndef tud_int_handler + #define tud_int_handler(_x) + #endif #endif -- cgit v1.3.1 From 824e585e2b1f62d1ed03f480439e62e5410636b6 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 18 Aug 2023 14:06:57 +0700 Subject: ground works for hcd max3421e --- .../boards/feather_nrf52840_express/board.cmake | 4 +- hw/bsp/nrf/boards/feather_nrf52840_express/board.h | 7 + hw/bsp/nrf/family.c | 80 ++++-- hw/bsp/nrf/family.cmake | 2 +- hw/bsp/nrf/nrfx_config.h | 5 +- src/portable/analog/max3421e/hcd_max3421e.c | 302 +++++++++++++++++++++ 6 files changed, 369 insertions(+), 31 deletions(-) create mode 100644 src/portable/analog/max3421e/hcd_max3421e.c (limited to 'src/portable') diff --git a/hw/bsp/nrf/boards/feather_nrf52840_express/board.cmake b/hw/bsp/nrf/boards/feather_nrf52840_express/board.cmake index 0acbecf7a..78ed98225 100644 --- a/hw/bsp/nrf/boards/feather_nrf52840_express/board.cmake +++ b/hw/bsp/nrf/boards/feather_nrf52840_express/board.cmake @@ -1,6 +1,6 @@ set(MCU_VARIANT nrf52840) -set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/../../linker/nrf52840_s140_v6.ld) -# set(LD_FILE_GNU ${NRFX_DIR}/mdk/nrf52840_xxaa.ld) +#set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/../../linker/nrf52840_s140_v6.ld) +set(LD_FILE_GNU ${NRFX_DIR}/mdk/nrf52840_xxaa.ld) function(update_board TARGET) endfunction() diff --git a/hw/bsp/nrf/boards/feather_nrf52840_express/board.h b/hw/bsp/nrf/boards/feather_nrf52840_express/board.h index 8e6ce3230..e19f88a3c 100644 --- a/hw/bsp/nrf/boards/feather_nrf52840_express/board.h +++ b/hw/bsp/nrf/boards/feather_nrf52840_express/board.h @@ -45,6 +45,13 @@ #define UART_RX_PIN 24 #define UART_TX_PIN 25 +// SPI for USB host shield +#define SPI_SCK_PIN 14 +#define SPI_MOSI_PIN 13 +#define SPI_MISO_PIN 15 +#define SPI_CS_PIN 27 +#define MAX3241E_INT_PIN 26 + #ifdef __cplusplus } #endif diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 9ca666e36..b6ed15122 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -40,6 +40,7 @@ #include "hal/nrf_gpio.h" #include "drivers/include/nrfx_power.h" #include "drivers/include/nrfx_uarte.h" +#include "drivers/include/nrfx_spim.h" #ifdef SOFTDEVICE_PRESENT #include "nrf_sdm.h" @@ -54,8 +55,7 @@ //--------------------------------------------------------------------+ // Forward USB interrupt events to TinyUSB IRQ Handler //--------------------------------------------------------------------+ -void USBD_IRQHandler(void) -{ +void USBD_IRQHandler(void) { tud_int_handler(0); } @@ -81,6 +81,7 @@ enum { #endif static nrfx_uarte_t _uart_id = NRFX_UARTE_INSTANCE(0); +static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(0); // tinyusb function that handles power event (detected, ready, removed) // We must call it within SD's SOC event handler, or set it as power event handler if SD is not enabled. @@ -88,13 +89,11 @@ extern void tusb_hal_nrf_power_event(uint32_t event); // nrf power callback, could be unused if SD is enabled or usb is disabled (board_test example) -TU_ATTR_UNUSED static void power_event_handler(nrfx_power_usb_evt_t event) -{ +TU_ATTR_UNUSED static void power_event_handler(nrfx_power_usb_evt_t event) { tusb_hal_nrf_power_event((uint32_t) event); } -void board_init(void) -{ +void board_init(void) { // stop LF clock just in case we jump from application without reset NRF_CLOCK->TASKS_LFCLKSTOP = 1UL; @@ -113,8 +112,7 @@ void board_init(void) SysTick_Config(SystemCoreClock/1000); // UART - nrfx_uarte_config_t uart_cfg = - { + nrfx_uarte_config_t uart_cfg = { .pseltxd = UART_TX_PIN, .pselrxd = UART_RX_PIN, .pselcts = NRF_UARTE_PSEL_DISCONNECTED, @@ -175,45 +173,78 @@ void board_init(void) if ( usb_reg & VBUSDETECT_Msk ) tusb_hal_nrf_power_event(USB_EVT_DETECTED); if ( usb_reg & OUTPUTRDY_Msk ) tusb_hal_nrf_power_event(USB_EVT_READY); #endif + + (void) _spi; +#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E + // USB host using max3421e usb controller via SPI + nrfx_spim_config_t cfg = { + .sck_pin = SPI_SCK_PIN, + .mosi_pin = SPI_MOSI_PIN, + .miso_pin = SPI_MISO_PIN, + .ss_pin = SPI_CS_PIN, + .ss_active_high = false, + .irq_priority = 3, + .orc = 0xFF, + // default setting 4 Mhz, Mode 0, MSB first + .frequency = NRF_SPIM_FREQ_4M, + .mode = NRF_SPIM_MODE_0, + .bit_order = NRF_SPIM_BIT_ORDER_MSB_FIRST, + }; + + // no handler --> blocking + nrfx_spim_init(&_spi, &cfg, NULL, NULL); +#endif + } //--------------------------------------------------------------------+ // Board porting API //--------------------------------------------------------------------+ -void board_led_write(bool state) -{ - nrf_gpio_pin_write(LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +void board_led_write(bool state) { + nrf_gpio_pin_write(LED_PIN, state ? LED_STATE_ON : (1 - LED_STATE_ON)); } -uint32_t board_button_read(void) -{ +uint32_t board_button_read(void) { return BUTTON_STATE_ACTIVE == nrf_gpio_pin_read(BUTTON_PIN); } -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; +int board_uart_read(uint8_t *buf, int len) { + (void) buf; + (void) len; return 0; // return NRFX_SUCCESS == nrfx_uart_rx(&_uart_id, buf, (size_t) len) ? len : 0; } -int board_uart_write(void const * buf, int len) -{ - return (NRFX_SUCCESS == nrfx_uarte_tx(&_uart_id, (uint8_t const*) buf, (size_t) len)) ? len : 0; +int board_uart_write(void const *buf, int len) { + return (NRFX_SUCCESS == nrfx_uarte_tx(&_uart_id, (uint8_t const *) buf, (size_t) len)) ? len : 0; } #if CFG_TUSB_OS == OPT_OS_NONE volatile uint32_t system_ticks = 0; -void SysTick_Handler (void) -{ + +void SysTick_Handler(void) { system_ticks++; } -uint32_t board_millis(void) -{ +uint32_t board_millis(void) { return system_ticks; } + +#endif + +#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E +// API: SPI transfer with MAX3421E, must be implemented by application +bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len) { + (void) rhport; + nrfx_spim_xfer_desc_t xfer = { + .p_tx_buffer = tx_buf, + .tx_length = tx_len, + .p_rx_buffer = rx_buf, + .rx_length = rx_len, + }; + return nrfx_spim_xfer(&_spi, &xfer, 0) == NRFX_SUCCESS; +} #endif #ifdef SOFTDEVICE_PRESENT @@ -251,8 +282,7 @@ void SD_EVT_IRQHandler(void) } } -void nrf_error_cb(uint32_t id, uint32_t pc, uint32_t info) -{ +void nrf_error_cb(uint32_t id, uint32_t pc, uint32_t info) { (void) id; (void) pc; (void) info; diff --git a/hw/bsp/nrf/family.cmake b/hw/bsp/nrf/family.cmake index 6c24d3658..527251e71 100644 --- a/hw/bsp/nrf/family.cmake +++ b/hw/bsp/nrf/family.cmake @@ -122,7 +122,7 @@ function(family_configure_example TARGET RTOS) family_add_tinyusb(${TARGET} OPT_MCU_NRF5X ${RTOS}) target_sources(${TARGET}-tinyusb PUBLIC ${TOP}/src/portable/nordic/nrf5x/dcd_nrf5x.c - #${TOP}/src/portable/analog/max3421e/hcd_max3421e.c + ${TOP}/src/portable/analog/max3421e/hcd_max3421e.c ) target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) diff --git a/hw/bsp/nrf/nrfx_config.h b/hw/bsp/nrf/nrfx_config.h index 696a3fb04..d0f718c6c 100644 --- a/hw/bsp/nrf/nrfx_config.h +++ b/hw/bsp/nrf/nrfx_config.h @@ -9,9 +9,8 @@ #define NRFX_UARTE_ENABLED 1 #define NRFX_UARTE0_ENABLED 1 -#define NRFX_UARTE1_ENABLED 0 -#define NRFX_UARTE2_ENABLED 0 -#define NRFX_UARTE3_ENABLED 0 +#define NRFX_SPIM_ENABLED 1 +#define NRFX_SPIM0_ENABLED 1 #define NRFX_PRS_ENABLED 0 #define NRFX_USBREG_ENABLED 1 diff --git a/src/portable/analog/max3421e/hcd_max3421e.c b/src/portable/analog/max3421e/hcd_max3421e.c new file mode 100644 index 000000000..7b9d73e4e --- /dev/null +++ b/src/portable/analog/max3421e/hcd_max3421e.c @@ -0,0 +1,302 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "tusb_option.h" + +#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E + +#include "host/hcd.h" + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +// Command format is +// Reg [7:3] | 0 [2] | Dir [1] | Ack [0] + +enum { + CMDBYTE_WRITE = 0x02, +}; + +enum { + RCVVFIFO_ADDR = 1u << 3, // 0x08 + SNDFIFO_ADDR = 2u << 3, // 0x10 + SUDFIFO_ADDR = 4u << 3, // 0x20 + RCVBC_ADDR = 6u << 3, // 0x30 + SNDBC_ADDR = 7u << 3, // 0x38 + USBIRQ_ADDR = 13u << 3, // 0x68 + USBIEN_ADDR = 14u << 3, // 0x70 + USBCTL_ADDR = 15u << 3, // 0x78 + CPUCTL_ADDR = 16u << 3, // 0x80 + PINCTL_ADDR = 17u << 3, // 0x88 + REVISION_ADDR = 18u << 3, // 0x90 + HIRQ_ADDR = 25u << 3, // 0xC8 + HIEN_ADDR = 26u << 3, // 0xD0 + MODE_ADDR = 27u << 3, // 0xD8 + PERADDR_ADDR = 28u << 3, // 0xE0 + HCTL_ADDR = 29u << 3, // 0xE8 + HXFR_ADDR = 30u << 3, // 0xF0 + HRSL_ADDR = 31u << 3, // 0xF8 +}; + +enum { + USBIRQ_OSCOK_IRQ = 1u << 0, + USBIRQ_NOVBUS_IRQ = 1u << 5, + USBIRQ_VBUS_IRQ = 1u << 6, +}; + +enum { + USBCTL_PWRDOWN = 1u << 4, + USBCTL_CHIPRES = 1u << 5, +}; + +enum { + CPUCTL_IE = 1u << 0, + CPUCTL_PULSEWID0 = 1u << 6, + CPUCTL_PULSEWID1 = 1u << 7, +}; + +enum { + PINCTL_GPXA = 1u << 0, + PINCTL_GPXB = 1u << 1, + PINCTL_POSINT = 1u << 2, + PINCTL_INTLEVEL = 1u << 3, + PINCTL_FDUPSPI = 1u << 4, +}; + +enum { + HIRQ_BUSEVENT_IRQ = 1u << 0, + HIRQ_RWU_IRQ = 1u << 1, + HIRQ_RCVDAV_IRQ = 1u << 2, + HIRQ_SNDBAV_IRQ = 1u << 3, + HIRQ_SUSDN_IRQ = 1u << 4, + HIRQ_CONDET_IRQ = 1u << 5, + HIRQ_FRAME_IRQ = 1u << 6, + HIRQ_HXFRDN_IRQ = 1u << 7, +}; + +enum { + MODE_HOST = 1u << 0, + MODE_LOWSPEED = 1u << 1, + MODE_HUBPRE = 1u << 2, + MODE_SOFKAENAB = 1u << 3, + MODE_SEPIRQ = 1u << 4, + MODE_DELAYISO = 1u << 5, + MODE_DMPULLDN = 1u << 6, + MODE_DPPULLDN = 1u << 7, +}; + +enum { + HCTL_BUSRST = 1u << 1, + HCTL_FRMRST = 1u << 2, + HCTL_SAMPLEBUS = 1u << 3, + HCTL_SIGRSM = 1u << 4, + HCTL_RCVTOG0 = 1u << 5, + HCTL_RCVTOG1 = 1u << 6, + HCTL_SNDTOG0 = 1u << 7, + HCTL_SNDTOG1 = 1u << 8, +}; + +enum { + HXFR_EPNUM_MASK = 0x0f, + HXFR_SETUP = 1u << 4, + HXFR_OUT_NIN = 1u << 5, + HXFR_ISO = 1u << 6, + HXFR_HS = 1u << 7, +}; + +enum { + HRSL_RESULT_MASK = 0x0f, + HRSL_RCVTOGRD = 1u << 4, + HRSL_SNDTOGRD = 1u << 5, + HRSL_KSTATUS = 1u << 6, + HRSL_JSTATUS = 1u << 7, +}; + +// API: SPI transfer with MAX3421E, must be implemented by application +bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len); + +// return HIRQ register since we are in full-duplex mode +static uint8_t reg_write(uint8_t reg, uint8_t data) { + uint8_t tx_buf[2] = {reg | CMDBYTE_WRITE, data}; + uint8_t rx_buf[2] = {0, 0}; + tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2); + return rx_buf[0]; +} + +static uint8_t reg_read(uint8_t reg) { + uint8_t tx_buf[2] = {reg, 0}; + uint8_t rx_buf[2] = {0, 0}; + return tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2) ? rx_buf[1] : 0; +} + + +//--------------------------------------------------------------------+ +// Controller API +//--------------------------------------------------------------------+ + +// optional hcd configuration, called by tuh_configure() +bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { + (void) rhport; + (void) cfg_id; + (void) cfg_param; + + return false; +} + +// Initialize controller to host mode +bool hcd_init(uint8_t rhport) { + (void) rhport; + + // full duplex, interrupt level (should be configurable) + reg_write(PINCTL_ADDR, PINCTL_FDUPSPI | PINCTL_INTLEVEL); + + // reset + reg_write(USBCTL_ADDR, USBCTL_CHIPRES); + reg_write(USBCTL_ADDR, 0); + while( !(reg_read(USBIRQ_ADDR) & USBIRQ_OSCOK_IRQ) ) { + // wait for oscillator to stabilize + } + + // Mode: Host and DP/DM pull down + reg_write(MODE_ADDR, MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST); + + // Connection detection + reg_write(HIEN_ADDR, HIRQ_CONDET_IRQ /*| HIRQ_FRAME_IRQ */); + + return false; +} + +// Interrupt Handler +void hcd_int_handler(uint8_t rhport) { + (void) rhport; +} + +// Enable USB interrupt +void hcd_int_enable (uint8_t rhport) { + (void) rhport; +} + +// Disable USB interrupt +void hcd_int_disable(uint8_t rhport) { + (void) rhport; +} + +// Get frame number (1ms) +uint32_t hcd_frame_number(uint8_t rhport) { + (void) rhport; + + return 0; +} + +//--------------------------------------------------------------------+ +// Port API +//--------------------------------------------------------------------+ + +// Get the current connect status of roothub port +bool hcd_port_connect_status(uint8_t rhport) { + (void) rhport; + + return false; +} + +// Reset USB bus on the port. Return immediately, bus reset sequence may not be complete. +// Some port would require hcd_port_reset_end() to be invoked after 10ms to complete the reset sequence. +void hcd_port_reset(uint8_t rhport) { + (void) rhport; +} + +// Complete bus reset sequence, may be required by some controllers +void hcd_port_reset_end(uint8_t rhport) { + (void) rhport; +} + +// Get port link speed +tusb_speed_t hcd_port_speed_get(uint8_t rhport) { + (void) rhport; + + return TUSB_SPEED_FULL; +} + +// HCD closes all opened endpoints belong to this device +void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { + (void) rhport; + (void) dev_addr; +} + +//--------------------------------------------------------------------+ +// Endpoints API +//--------------------------------------------------------------------+ + +// Open an endpoint +bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc) { + (void) rhport; + (void) dev_addr; + (void) ep_desc; + + return false; +} + +// Submit a transfer, when complete hcd_event_xfer_complete() must be invoked +bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + (void) buffer; + (void) buflen; + + return false; +} + +// Abort a queued transfer. Note: it can only abort transfer that has not been started +// Return true if a queued transfer is aborted, false if there is no transfer to abort +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + + return false; +} + +// Submit a special transfer to send 8-byte Setup Packet, when complete hcd_event_xfer_complete() must be invoked +bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { + (void) rhport; + (void) dev_addr; + (void) setup_packet; + + return false; +} + +// clear stall, data toggle is also reset to DATA0 +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + + return false; +} + +#endif -- cgit v1.3.1 From cacc96b25dc04865389357467b7a6d92d040ef36 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 18 Aug 2023 17:39:10 +0700 Subject: adding connection event handling, add nrf gpio interrupt for max2341e interrupt pin --- hw/bsp/nrf/boards/feather_nrf52840_express/board.h | 2 +- hw/bsp/nrf/family.c | 55 +++++++++++----- hw/bsp/nrf/family.cmake | 2 + hw/bsp/nrf/nrfx_config.h | 2 +- hw/bsp/nrf/nrfx_glue.h | 69 ++++++++++++++++++++ src/portable/analog/max3421e/hcd_max3421e.c | 76 +++++++++++++++++++++- 6 files changed, 184 insertions(+), 22 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/nrf/boards/feather_nrf52840_express/board.h b/hw/bsp/nrf/boards/feather_nrf52840_express/board.h index e19f88a3c..7f042142e 100644 --- a/hw/bsp/nrf/boards/feather_nrf52840_express/board.h +++ b/hw/bsp/nrf/boards/feather_nrf52840_express/board.h @@ -50,7 +50,7 @@ #define SPI_MOSI_PIN 13 #define SPI_MISO_PIN 15 #define SPI_CS_PIN 27 -#define MAX3241E_INT_PIN 26 +#define MAX3241E_INTR_PIN 26 #ifdef __cplusplus } diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index b6ed15122..e58ee845b 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -38,6 +38,7 @@ #include "nrfx.h" #include "hal/nrf_gpio.h" +#include "drivers/include/nrfx_gpiote.h" #include "drivers/include/nrfx_power.h" #include "drivers/include/nrfx_uarte.h" #include "drivers/include/nrfx_spim.h" @@ -81,18 +82,45 @@ enum { #endif static nrfx_uarte_t _uart_id = NRFX_UARTE_INSTANCE(0); -static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(0); // tinyusb function that handles power event (detected, ready, removed) // We must call it within SD's SOC event handler, or set it as power event handler if SD is not enabled. extern void tusb_hal_nrf_power_event(uint32_t event); - // nrf power callback, could be unused if SD is enabled or usb is disabled (board_test example) TU_ATTR_UNUSED static void power_event_handler(nrfx_power_usb_evt_t event) { tusb_hal_nrf_power_event((uint32_t) event); } +//------------- Host using MAX2341E -------------// +#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E +static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(0); + +void max2342e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { + if ( !(pin == MAX3241E_INTR_PIN && action == NRF_GPIOTE_POLARITY_HITOLO) ) return; + + tuh_int_handler(1); +} + +// API: SPI transfer with MAX3421E, must be implemented by application +bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len) { + (void) rhport; + nrfx_spim_xfer_desc_t xfer = { + .p_tx_buffer = tx_buf, + .tx_length = tx_len, + .p_rx_buffer = rx_buf, + .rx_length = rx_len, + }; + return nrfx_spim_xfer(&_spi, &xfer, 0) == NRFX_SUCCESS; +} + +#endif + + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + void board_init(void) { // stop LF clock just in case we jump from application without reset NRF_CLOCK->TASKS_LFCLKSTOP = 1UL; @@ -174,7 +202,6 @@ void board_init(void) { if ( usb_reg & OUTPUTRDY_Msk ) tusb_hal_nrf_power_event(USB_EVT_READY); #endif - (void) _spi; #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E // USB host using max3421e usb controller via SPI nrfx_spim_config_t cfg = { @@ -193,6 +220,14 @@ void board_init(void) { // no handler --> blocking nrfx_spim_init(&_spi, &cfg, NULL, NULL); + + // max3421e interrupt pin + nrfx_gpiote_init(1); + nrfx_gpiote_in_config_t in_config = NRFX_GPIOTE_CONFIG_IN_SENSE_HITOLO(true); + in_config.pull = NRF_GPIO_PIN_PULLUP; + + nrfx_gpiote_in_init(MAX3241E_INTR_PIN, &in_config, max2342e_int_handler); + nrfx_gpiote_in_event_enable(MAX3241E_INTR_PIN, true); #endif } @@ -233,20 +268,6 @@ uint32_t board_millis(void) { #endif -#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E -// API: SPI transfer with MAX3421E, must be implemented by application -bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len) { - (void) rhport; - nrfx_spim_xfer_desc_t xfer = { - .p_tx_buffer = tx_buf, - .tx_length = tx_len, - .p_rx_buffer = rx_buf, - .rx_length = rx_len, - }; - return nrfx_spim_xfer(&_spi, &xfer, 0) == NRFX_SUCCESS; -} -#endif - #ifdef SOFTDEVICE_PRESENT // process SOC event from SD uint32_t proc_soc(void) diff --git a/hw/bsp/nrf/family.cmake b/hw/bsp/nrf/family.cmake index 527251e71..8bf7bcb52 100644 --- a/hw/bsp/nrf/family.cmake +++ b/hw/bsp/nrf/family.cmake @@ -32,6 +32,8 @@ function(add_board_target BOARD_TARGET) if (NOT TARGET ${BOARD_TARGET}) add_library(${BOARD_TARGET} STATIC # driver + ${NRFX_DIR}/helpers/nrfx_flag32_allocator.c + ${NRFX_DIR}/drivers/src/nrfx_gpiote.c ${NRFX_DIR}/drivers/src/nrfx_power.c ${NRFX_DIR}/drivers/src/nrfx_spim.c ${NRFX_DIR}/drivers/src/nrfx_uarte.c diff --git a/hw/bsp/nrf/nrfx_config.h b/hw/bsp/nrf/nrfx_config.h index d0f718c6c..e3d0ea91b 100644 --- a/hw/bsp/nrf/nrfx_config.h +++ b/hw/bsp/nrf/nrfx_config.h @@ -5,6 +5,7 @@ #define NRFX_POWER_DEFAULT_CONFIG_IRQ_PRIORITY 7 #define NRFX_CLOCK_ENABLED 0 +#define NRFX_GPIOTE_ENABLED 1 #define NRFX_UARTE_ENABLED 1 #define NRFX_UARTE0_ENABLED 1 @@ -41,5 +42,4 @@ #error "Unknown device." #endif - #endif // NRFX_CONFIG_H__ diff --git a/hw/bsp/nrf/nrfx_glue.h b/hw/bsp/nrf/nrfx_glue.h index cdf49b4ab..ef756c670 100644 --- a/hw/bsp/nrf/nrfx_glue.h +++ b/hw/bsp/nrf/nrfx_glue.h @@ -220,6 +220,75 @@ static inline bool _NRFX_IRQ_IS_PENDING(IRQn_Type irq_number) /** @} */ +//------------------------------------------------------------------------------ + +#include + +/** + * @brief Atomic 32 bit unsigned type. + */ +#define nrfx_atomic_t nrfx_atomic_u32_t + +/** + * @brief Stores value to an atomic object and returns previously stored value. + * + * @param[in] p_data Atomic memory pointer. + * @param[in] value Value to store. + * + * @return Old value stored into atomic object. + */ +#define NRFX_ATOMIC_FETCH_STORE(p_data, value) nrfx_atomic_u32_fetch_store(p_data, value) + +/** + * @brief Performs logical OR operation on an atomic object and returns previously stored value. + * + * @param[in] p_data Atomic memory pointer. + * @param[in] value Value of second operand of OR operation. + * + * @return Old value stored into atomic object. + */ +#define NRFX_ATOMIC_FETCH_OR(p_data, value) nrfx_atomic_u32_fetch_or(p_data, value) + +/** + * @brief Performs logical AND operation on an atomic object and returns previously stored value. + * + * @param[in] p_data Atomic memory pointer. + * @param[in] value Value of second operand of AND operation. + * + * @return Old value stored into atomic object. + */ +#define NRFX_ATOMIC_FETCH_AND(p_data, value) nrfx_atomic_u32_fetch_and(p_data, value) + +/** + * @brief Performs logical XOR operation on an atomic object and returns previously stored value. + * + * @param[in] p_data Atomic memory pointer. + * @param[in] value Value of second operand of XOR operation. + * + * @return Old value stored into atomic object. + */ +#define NRFX_ATOMIC_FETCH_XOR(p_data, value) nrfx_atomic_u32_fetch_xor(p_data, value) + +/** + * @brief Performs logical ADD operation on an atomic object and returns previously stored value. + * + * @param[in] p_data Atomic memory pointer. + * @param[in] value Value of second operand of ADD operation. + * + * @return Old value stored into atomic object. + */ +#define NRFX_ATOMIC_FETCH_ADD(p_data, value) nrfx_atomic_u32_fetch_add(p_data, value) + +/** + * @brief Performs logical SUB operation on an atomic object and returns previously stored value. + * + * @param[in] p_data Atomic memory pointer. + * @param[in] value Value of second operand of SUB operation. + * + * @return Old value stored into atomic object. + */ +#define NRFX_ATOMIC_FETCH_SUB(p_data, value) nrfx_atomic_u32_fetch_sub(p_data, value) + #ifdef __cplusplus } #endif diff --git a/src/portable/analog/max3421e/hcd_max3421e.c b/src/portable/analog/max3421e/hcd_max3421e.c index 7b9d73e4e..a89581b9c 100644 --- a/src/portable/analog/max3421e/hcd_max3421e.c +++ b/src/portable/analog/max3421e/hcd_max3421e.c @@ -136,6 +136,20 @@ enum { HRSL_JSTATUS = 1u << 7, }; +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +//typedef struct { +// uint8_t mode +//} max2341e_data_t; +// +//max2341e_data_t max2341e_data; + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + // API: SPI transfer with MAX3421E, must be implemented by application bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len); @@ -144,6 +158,7 @@ static uint8_t reg_write(uint8_t reg, uint8_t data) { uint8_t tx_buf[2] = {reg | CMDBYTE_WRITE, data}; uint8_t rx_buf[2] = {0, 0}; tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2); + TU_LOG2("HIRQ: %02X\r\n", rx_buf[0]); return rx_buf[0]; } @@ -167,6 +182,48 @@ bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { return false; } +tusb_speed_t handle_connect_irq(uint8_t rhport) { + (void) rhport; + + uint8_t const hrsl = reg_read(HRSL_ADDR); + uint8_t const jk = hrsl & (HRSL_JSTATUS | HRSL_KSTATUS); + + tusb_speed_t speed; + uint8_t new_mode = MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST; + + switch(jk) { + case 0x00: + // SEO is disconnected + speed = TUSB_SPEED_INVALID; + break; + + case (HRSL_JSTATUS | HRSL_KSTATUS): + // SE1 is illegal + speed = TUSB_SPEED_INVALID; + break; + + default: { + // Low speed if (LS = 1 and J-state) or (LS = 0 and K-State) + uint8_t const mode = reg_read(MODE_ADDR); + uint8_t const ls_bit = mode & MODE_LOWSPEED; + + if ( (ls_bit && (jk == HRSL_JSTATUS)) || (!ls_bit && (jk == HRSL_KSTATUS)) ) { + speed = TUSB_SPEED_LOW; + new_mode |= MODE_LOWSPEED; + } else { + speed = TUSB_SPEED_FULL; + } + + new_mode |= MODE_SOFKAENAB; // enable SOF since there is new device + + break; + } + } + + reg_write(MODE_ADDR, new_mode); + return speed; +} + // Initialize controller to host mode bool hcd_init(uint8_t rhport) { (void) rhport; @@ -184,15 +241,28 @@ bool hcd_init(uint8_t rhport) { // Mode: Host and DP/DM pull down reg_write(MODE_ADDR, MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST); - // Connection detection - reg_write(HIEN_ADDR, HIRQ_CONDET_IRQ /*| HIRQ_FRAME_IRQ */); + // Enable Connection IRQ + reg_write(HIEN_ADDR, HIRQ_CONDET_IRQ); - return false; + // Note: if device is already connected, CONDET IRQ may not be triggered. We need to detect it by sampling bus signal + reg_write(HCTL_ADDR, HCTL_SAMPLEBUS); + while( !(reg_read(HCTL_ADDR) & HCTL_SAMPLEBUS) ) {} + + handle_connect_irq(rhport); + reg_write(HIRQ_ADDR, HIRQ_CONDET_IRQ); + + // Enable Interrupt pin + reg_write(CPUCTL_ADDR, CPUCTL_IE); + + return true; } // Interrupt Handler void hcd_int_handler(uint8_t rhport) { (void) rhport; + + uint8_t hirq = reg_read(HIRQ_ADDR); + TU_LOG3_INT(hirq); } // Enable USB interrupt -- cgit v1.3.1 From b4134394166c1f77463b5cb62f28cff465fde174 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 22 Aug 2023 19:57:59 +0700 Subject: able to detect new device and start enumerating --- src/portable/analog/max3421e/hcd_max3421e.c | 70 +++++++++++++++++++++-------- 1 file changed, 51 insertions(+), 19 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421e/hcd_max3421e.c b/src/portable/analog/max3421e/hcd_max3421e.c index a89581b9c..870c616a9 100644 --- a/src/portable/analog/max3421e/hcd_max3421e.c +++ b/src/portable/analog/max3421e/hcd_max3421e.c @@ -140,11 +140,13 @@ enum { // //--------------------------------------------------------------------+ -//typedef struct { -// uint8_t mode -//} max2341e_data_t; -// -//max2341e_data_t max2341e_data; +typedef struct { + uint8_t mode; + + volatile uint16_t frame_count; +} max2341e_data_t; + +static max2341e_data_t _hcd_data; //--------------------------------------------------------------------+ // @@ -168,6 +170,11 @@ static uint8_t reg_read(uint8_t reg) { return tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2) ? rx_buf[1] : 0; } +static inline uint8_t mode_write(uint8_t data) { + _hcd_data.mode = data; + return reg_write(MODE_ADDR, data); +} + //--------------------------------------------------------------------+ // Controller API @@ -220,7 +227,8 @@ tusb_speed_t handle_connect_irq(uint8_t rhport) { } } - reg_write(MODE_ADDR, new_mode); + mode_write(new_mode); + TU_LOG2_INT(speed); return speed; } @@ -228,6 +236,8 @@ tusb_speed_t handle_connect_irq(uint8_t rhport) { bool hcd_init(uint8_t rhport) { (void) rhport; + tu_memclr(&_hcd_data, sizeof(_hcd_data)); + // full duplex, interrupt level (should be configurable) reg_write(PINCTL_ADDR, PINCTL_FDUPSPI | PINCTL_INTLEVEL); @@ -239,17 +249,21 @@ bool hcd_init(uint8_t rhport) { } // Mode: Host and DP/DM pull down - reg_write(MODE_ADDR, MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST); + mode_write(MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST); // Enable Connection IRQ - reg_write(HIEN_ADDR, HIRQ_CONDET_IRQ); + reg_write(HIEN_ADDR, HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ); - // Note: if device is already connected, CONDET IRQ may not be triggered. We need to detect it by sampling bus signal + #if 0 + // Note: if device is already connected, CONDET IRQ may not be triggered. + // We need to detect it by sampling bus signal. FIXME not working reg_write(HCTL_ADDR, HCTL_SAMPLEBUS); - while( !(reg_read(HCTL_ADDR) & HCTL_SAMPLEBUS) ) {} + while ( reg_read(HCTL_ADDR) & HCTL_SAMPLEBUS ) {} - handle_connect_irq(rhport); - reg_write(HIRQ_ADDR, HIRQ_CONDET_IRQ); + if ( TUSB_SPEED_INVALID != handle_connect_irq(rhport) ) { + reg_write(HIRQ_ADDR, HIRQ_CONDET_IRQ); // clear connect irq + } + #endif // Enable Interrupt pin reg_write(CPUCTL_ADDR, CPUCTL_IE); @@ -262,7 +276,26 @@ void hcd_int_handler(uint8_t rhport) { (void) rhport; uint8_t hirq = reg_read(HIRQ_ADDR); - TU_LOG3_INT(hirq); + TU_LOG3_HEX(hirq); + + if (hirq & HIRQ_CONDET_IRQ) { + tusb_speed_t speed = handle_connect_irq(rhport); + + if (speed == TUSB_SPEED_INVALID) { + hcd_event_device_remove(rhport, true); + }else { + hcd_event_device_attach(rhport, true); + } + } + + if (hirq & HIRQ_FRAME_IRQ) { + _hcd_data.frame_count++; + } + + // clear all interrupt + if ( hirq ) { + reg_write(HIRQ_ADDR, hirq); + } } // Enable USB interrupt @@ -278,8 +311,7 @@ void hcd_int_disable(uint8_t rhport) { // Get frame number (1ms) uint32_t hcd_frame_number(uint8_t rhport) { (void) rhport; - - return 0; + return (uint32_t ) _hcd_data.frame_count; } //--------------------------------------------------------------------+ @@ -289,26 +321,26 @@ uint32_t hcd_frame_number(uint8_t rhport) { // Get the current connect status of roothub port bool hcd_port_connect_status(uint8_t rhport) { (void) rhport; - - return false; + return (_hcd_data.mode & MODE_SOFKAENAB) ? true : false; } // Reset USB bus on the port. Return immediately, bus reset sequence may not be complete. // Some port would require hcd_port_reset_end() to be invoked after 10ms to complete the reset sequence. void hcd_port_reset(uint8_t rhport) { (void) rhport; + reg_write(HCTL_ADDR, HCTL_BUSRST); } // Complete bus reset sequence, may be required by some controllers void hcd_port_reset_end(uint8_t rhport) { (void) rhport; + reg_write(HCTL_ADDR, 0); } // Get port link speed tusb_speed_t hcd_port_speed_get(uint8_t rhport) { (void) rhport; - - return TUSB_SPEED_FULL; + return (_hcd_data.mode & MODE_LOWSPEED) ? TUSB_SPEED_LOW : TUSB_SPEED_FULL; } // HCD closes all opened endpoints belong to this device -- cgit v1.3.1 From 274578ff46c31b231b3553dc9a20895646313130 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 22 Aug 2023 23:17:12 +0700 Subject: able to send setup packet --- hw/bsp/nrf/boards/feather_nrf52840_express/board.h | 8 +- hw/bsp/nrf/family.c | 36 ++++- src/host/hcd.h | 2 +- src/host/usbh.c | 32 ++-- src/portable/analog/max3421e/hcd_max3421e.c | 173 ++++++++++++++++----- 5 files changed, 179 insertions(+), 72 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/nrf/boards/feather_nrf52840_express/board.h b/hw/bsp/nrf/boards/feather_nrf52840_express/board.h index 7f042142e..e6e7590ac 100644 --- a/hw/bsp/nrf/boards/feather_nrf52840_express/board.h +++ b/hw/bsp/nrf/boards/feather_nrf52840_express/board.h @@ -46,10 +46,10 @@ #define UART_TX_PIN 25 // SPI for USB host shield -#define SPI_SCK_PIN 14 -#define SPI_MOSI_PIN 13 -#define SPI_MISO_PIN 15 -#define SPI_CS_PIN 27 +#define MAX3421E_SCK_PIN 14 +#define MAX3421E_MOSI_PIN 13 +#define MAX3421E_MISO_PIN 15 +#define MAX3421E_CS_PIN 27 #define MAX3241E_INTR_PIN 26 #ifdef __cplusplus diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index e58ee845b..862f67bc7 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -96,22 +96,38 @@ TU_ATTR_UNUSED static void power_event_handler(nrfx_power_usb_evt_t event) { #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(0); -void max2342e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { +void max3421e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { if ( !(pin == MAX3241E_INTR_PIN && action == NRF_GPIOTE_POLARITY_HITOLO) ) return; tuh_int_handler(1); } +static inline void max3421e_cs_assert(bool active) { + nrf_gpio_pin_write(MAX3421E_CS_PIN, active ? 0 : 1); +} + +//--------------------------------------------------------------------+ // API: SPI transfer with MAX3421E, must be implemented by application -bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len) { +//--------------------------------------------------------------------+ + +bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, + uint8_t * rx_buf, size_t rx_len, bool keep_cs) { (void) rhport; + + max3421e_cs_assert(true); + nrfx_spim_xfer_desc_t xfer = { .p_tx_buffer = tx_buf, .tx_length = tx_len, .p_rx_buffer = rx_buf, .rx_length = rx_len, }; - return nrfx_spim_xfer(&_spi, &xfer, 0) == NRFX_SUCCESS; + + bool ret = (nrfx_spim_xfer(&_spi, &xfer, 0) == NRFX_SUCCESS); + + if ( !keep_cs ) max3421e_cs_assert(false); + + return ret; } #endif @@ -203,12 +219,16 @@ void board_init(void) { #endif #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E + // manually manage CS + nrf_gpio_cfg_output(MAX3421E_CS_PIN); + max3421e_cs_assert(false); + // USB host using max3421e usb controller via SPI nrfx_spim_config_t cfg = { - .sck_pin = SPI_SCK_PIN, - .mosi_pin = SPI_MOSI_PIN, - .miso_pin = SPI_MISO_PIN, - .ss_pin = SPI_CS_PIN, + .sck_pin = MAX3421E_SCK_PIN, + .mosi_pin = MAX3421E_MOSI_PIN, + .miso_pin = MAX3421E_MISO_PIN, + .ss_pin = NRFX_SPIM_PIN_NOT_USED, .ss_active_high = false, .irq_priority = 3, .orc = 0xFF, @@ -226,7 +246,7 @@ void board_init(void) { nrfx_gpiote_in_config_t in_config = NRFX_GPIOTE_CONFIG_IN_SENSE_HITOLO(true); in_config.pull = NRF_GPIO_PIN_PULLUP; - nrfx_gpiote_in_init(MAX3241E_INTR_PIN, &in_config, max2342e_int_handler); + nrfx_gpiote_in_init(MAX3241E_INTR_PIN, &in_config, max3421e_int_handler); nrfx_gpiote_in_event_enable(MAX3241E_INTR_PIN, true); #endif diff --git a/src/host/hcd.h b/src/host/hcd.h index 1b5038ef4..079877b79 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -177,7 +177,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr); // Submit a special transfer to send 8-byte Setup Packet, when complete hcd_event_xfer_complete() must be invoked -bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]); +bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8]); // clear stall, data toggle is also reset to DATA0 bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr); diff --git a/src/host/usbh.c b/src/host/usbh.c index 5423df669..7a09f5b6e 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -552,8 +552,7 @@ static void _control_blocking_complete_cb(tuh_xfer_t* xfer) } // TODO timeout_ms is not supported yet -bool tuh_control_xfer (tuh_xfer_t* xfer) -{ +bool tuh_control_xfer (tuh_xfer_t* xfer) { // EP0 with setup packet TU_VERIFY(xfer->ep_addr == 0 && xfer->setup); @@ -565,8 +564,7 @@ bool tuh_control_xfer (tuh_xfer_t* xfer) (void) osal_mutex_lock(_usbh_mutex, OSAL_TIMEOUT_WAIT_FOREVER); bool const is_idle = (_ctrl_xfer.stage == CONTROL_STAGE_IDLE); - if (is_idle) - { + if (is_idle) { _ctrl_xfer.stage = CONTROL_STAGE_SETUP; _ctrl_xfer.daddr = daddr; _ctrl_xfer.actual_len = 0; @@ -588,11 +586,9 @@ bool tuh_control_xfer (tuh_xfer_t* xfer) TU_LOG_PTR(CFG_TUH_LOG_LEVEL, xfer->setup); TU_LOG_USBH("\r\n"); - if (xfer->complete_cb) - { + if (xfer->complete_cb) { TU_ASSERT( hcd_setup_send(rhport, daddr, (uint8_t const*) &_ctrl_xfer.request) ); - }else - { + }else { // blocking if complete callback is not provided // change callback to internal blocking, and result as user argument volatile xfer_result_t result = XFER_RESULT_INVALID; @@ -656,15 +652,13 @@ static void _xfer_complete(uint8_t daddr, xfer_result_t result) } } -static bool usbh_control_xfer_cb (uint8_t dev_addr, uint8_t ep_addr, xfer_result_t result, uint32_t xferred_bytes) -{ +static bool usbh_control_xfer_cb (uint8_t dev_addr, uint8_t ep_addr, xfer_result_t result, uint32_t xferred_bytes) { (void) ep_addr; const uint8_t rhport = usbh_get_rhport(dev_addr); tusb_control_request_t const * request = &_ctrl_xfer.request; - if (XFER_RESULT_SUCCESS != result) - { + if (XFER_RESULT_SUCCESS != result) { TU_LOG1("[%u:%u] Control %s, xferred_bytes = %lu\r\n", rhport, dev_addr, result == XFER_RESULT_STALLED ? "STALLED" : "FAILED", xferred_bytes); #if CFG_TUSB_DEBUG == 1 TU_LOG1_PTR(request); @@ -673,13 +667,10 @@ static bool usbh_control_xfer_cb (uint8_t dev_addr, uint8_t ep_addr, xfer_result // terminate transfer if any stage failed _xfer_complete(dev_addr, result); - }else - { - switch(_ctrl_xfer.stage) - { + }else { + switch(_ctrl_xfer.stage) { case CONTROL_STAGE_SETUP: - if (request->wLength) - { + if (request->wLength) { // DATA stage: initial data toggle is always 1 _set_control_xfer_stage(CONTROL_STAGE_DATA); TU_ASSERT( hcd_edpt_xfer(rhport, dev_addr, tu_edpt_addr(0, request->bmRequestType_bit.direction), _ctrl_xfer.buffer, request->wLength) ); @@ -688,8 +679,7 @@ static bool usbh_control_xfer_cb (uint8_t dev_addr, uint8_t ep_addr, xfer_result TU_ATTR_FALLTHROUGH; case CONTROL_STAGE_DATA: - if (request->wLength) - { + if (request->wLength) { TU_LOG_USBH("[%u:%u] Control data:\r\n", rhport, dev_addr); TU_LOG_MEM(CFG_TUH_LOG_LEVEL, _ctrl_xfer.buffer, xferred_bytes, 2); } @@ -1538,9 +1528,7 @@ static bool enum_new_device(hcd_event_t* event) xfer.result = XFER_RESULT_SUCCESS; xfer.user_data = ENUM_ADDR0_DEVICE_DESC; - process_enumeration(&xfer); - } #if CFG_TUH_HUB else diff --git a/src/portable/analog/max3421e/hcd_max3421e.c b/src/portable/analog/max3421e/hcd_max3421e.c index 870c616a9..c9596f695 100644 --- a/src/portable/analog/max3421e/hcd_max3421e.c +++ b/src/portable/analog/max3421e/hcd_max3421e.c @@ -136,30 +136,64 @@ enum { HRSL_JSTATUS = 1u << 7, }; +enum { + HRSL_SUCCESS = 0, + HRSL_BUSY, + HRSL_BAD_REQ, + HRSL_UNDEF, + HRSL_NAK, + HRSL_STALL, + HRSL_TOG_ERR, + HRSL_WRONG_PID, + HRSL_BAD_BYTECOUNT, + HRSL_PID_ERR, + HRSL_PKT_ERR, + HRSL_CRC_ERR, + HRSL_K_ERR, + HRSL_J_ERR, + HRSL_TIMEOUT, + HRSL_BABBLE, +}; + + //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ typedef struct { + // cached register uint8_t mode; + uint8_t peraddr; + uint8_t hxfr; volatile uint16_t frame_count; + + struct { + uint16_t packet_size; + uint16_t total_len; + uint8_t xfer_type; + }ep[8][2]; } max2341e_data_t; static max2341e_data_t _hcd_data; //--------------------------------------------------------------------+ -// +// API: SPI transfer with MAX3421E, must be implemented by application //--------------------------------------------------------------------+ -// API: SPI transfer with MAX3421E, must be implemented by application -bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len); +bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, + uint8_t * rx_buf, size_t rx_len, bool keep_cs); +//void tuh_max3421e_int_enable(uint8_t rhport, bool enabled); + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ // return HIRQ register since we are in full-duplex mode static uint8_t reg_write(uint8_t reg, uint8_t data) { uint8_t tx_buf[2] = {reg | CMDBYTE_WRITE, data}; uint8_t rx_buf[2] = {0, 0}; - tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2); + tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2, false); TU_LOG2("HIRQ: %02X\r\n", rx_buf[0]); return rx_buf[0]; } @@ -167,7 +201,7 @@ static uint8_t reg_write(uint8_t reg, uint8_t data) { static uint8_t reg_read(uint8_t reg) { uint8_t tx_buf[2] = {reg, 0}; uint8_t rx_buf[2] = {0, 0}; - return tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2) ? rx_buf[1] : 0; + return tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2, false) ? rx_buf[1] : 0; } static inline uint8_t mode_write(uint8_t data) { @@ -175,6 +209,24 @@ static inline uint8_t mode_write(uint8_t data) { return reg_write(MODE_ADDR, data); } +static inline uint8_t peraddr_write(uint8_t data) { + if ( _hcd_data.peraddr == data ) return 0; // no need to change address + + _hcd_data.peraddr = data; + return reg_write(PERADDR_ADDR, data); +} + +static inline uint8_t hxfr_write(uint8_t data) { + _hcd_data.hxfr = data; + return reg_write(HXFR_ADDR, data); +} + +static void fifo_write(uint8_t reg, uint8_t const * buffer, uint16_t len) { + uint8_t tx_buf[1] = {reg | CMDBYTE_WRITE}; + tuh_max3421e_spi_xfer_api(0, tx_buf, 1, NULL, 0, true); + tuh_max3421e_spi_xfer_api(0, buffer, len, NULL, 0, false); +} + //--------------------------------------------------------------------+ // Controller API @@ -252,7 +304,7 @@ bool hcd_init(uint8_t rhport) { mode_write(MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST); // Enable Connection IRQ - reg_write(HIEN_ADDR, HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ); + reg_write(HIEN_ADDR, HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ | HIRQ_HXFRDN_IRQ); #if 0 // Note: if device is already connected, CONDET IRQ may not be triggered. @@ -271,33 +323,6 @@ bool hcd_init(uint8_t rhport) { return true; } -// Interrupt Handler -void hcd_int_handler(uint8_t rhport) { - (void) rhport; - - uint8_t hirq = reg_read(HIRQ_ADDR); - TU_LOG3_HEX(hirq); - - if (hirq & HIRQ_CONDET_IRQ) { - tusb_speed_t speed = handle_connect_irq(rhport); - - if (speed == TUSB_SPEED_INVALID) { - hcd_event_device_remove(rhport, true); - }else { - hcd_event_device_attach(rhport, true); - } - } - - if (hirq & HIRQ_FRAME_IRQ) { - _hcd_data.frame_count++; - } - - // clear all interrupt - if ( hirq ) { - reg_write(HIRQ_ADDR, hirq); - } -} - // Enable USB interrupt void hcd_int_enable (uint8_t rhport) { (void) rhport; @@ -359,7 +384,12 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const (void) dev_addr; (void) ep_desc; - return false; + uint8_t ep_num = tu_edpt_number(ep_desc->bEndpointAddress); + uint8_t ep_dir = tu_edpt_dir(ep_desc->bEndpointAddress); + + _hcd_data.ep[ep_num][ep_dir].packet_size = tu_edpt_packet_size(ep_desc); + + return true; } // Submit a transfer, when complete hcd_event_xfer_complete() must be invoked @@ -384,12 +414,18 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { } // Submit a special transfer to send 8-byte Setup Packet, when complete hcd_event_xfer_complete() must be invoked -bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet[8]) { +bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8]) { (void) rhport; - (void) dev_addr; + (void) daddr; (void) setup_packet; - return false; + _hcd_data.ep[0][0].total_len = 8; + + peraddr_write(daddr); + fifo_write(SUDFIFO_ADDR, setup_packet, 8); + hxfr_write(HXFR_SETUP); + + return true; } // clear stall, data toggle is also reset to DATA0 @@ -401,4 +437,67 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { return false; } +// Interrupt Handler +void hcd_int_handler(uint8_t rhport) { + uint8_t hirq = reg_read(HIRQ_ADDR); + TU_LOG3_HEX(hirq); + + if (hirq & HIRQ_CONDET_IRQ) { + tusb_speed_t speed = handle_connect_irq(rhport); + + if (speed == TUSB_SPEED_INVALID) { + hcd_event_device_remove(rhport, true); + }else { + hcd_event_device_attach(rhport, true); + } + } + + if (hirq & HIRQ_FRAME_IRQ) { + _hcd_data.frame_count++; + } + + if (hirq & HIRQ_HXFRDN_IRQ) { + uint8_t const hrsl = reg_read(HRSL_ADDR); + uint8_t const result = hrsl & HRSL_RESULT_MASK; + uint8_t xfer_result; + + TU_LOG3("HRSL: %02X\r\n", hrsl); + switch(result) { + case HRSL_SUCCESS: + xfer_result = XFER_RESULT_SUCCESS; + break; + + case HRSL_STALL: + xfer_result = XFER_RESULT_STALLED; + break; + + default: + xfer_result = XFER_RESULT_FAILED; + break; + } + + uint8_t ep_dir = 0; + uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; + uint8_t const xfer_type = _hcd_data.hxfr & 0xf0; + + if ( xfer_type & HXFR_SETUP ) { + // SETUP transfer + ep_dir = 0; + }else if ( !(xfer_type & HXFR_OUT_NIN) ) { + // IN transfer + ep_dir = 1; + } + + uint8_t const ep_addr = tu_edpt_addr(ep_num, ep_dir); + uint16_t xferred_len = _hcd_data.ep[ep_num][ep_dir].total_len; + + hcd_event_xfer_complete(_hcd_data.peraddr, ep_addr, xferred_len, xfer_result, true); + } + + // clear all interrupt + if ( hirq ) { + reg_write(HIRQ_ADDR, hirq); + } +} + #endif -- cgit v1.3.1 From e3f3179924f7c84c4bb3e69234720f9afc178727 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 23 Aug 2023 15:08:12 +0700 Subject: able to get 8 byte descriptor, but read(RCVBC) always return 0 - rename max3421e to max3421 - fix incorrect bitmask for HCTL, fix initial device connect - fix bus reset cause connect IRQ --- hw/bsp/nrf/family.c | 24 +- hw/bsp/nrf/family.cmake | 2 +- src/host/hcd.h | 2 +- src/portable/analog/max3421/hcd_max3421.c | 613 ++++++++++++++++++++++++++++ src/portable/analog/max3421e/hcd_max3421e.c | 503 ----------------------- 5 files changed, 624 insertions(+), 520 deletions(-) create mode 100644 src/portable/analog/max3421/hcd_max3421.c delete mode 100644 src/portable/analog/max3421e/hcd_max3421e.c (limited to 'src/portable') diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 862f67bc7..45a5166a7 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -93,7 +93,7 @@ TU_ATTR_UNUSED static void power_event_handler(nrfx_power_usb_evt_t event) { } //------------- Host using MAX2341E -------------// -#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E +#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(0); void max3421e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { @@ -102,19 +102,17 @@ void max3421e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { tuh_int_handler(1); } -static inline void max3421e_cs_assert(bool active) { - nrf_gpio_pin_write(MAX3421E_CS_PIN, active ? 0 : 1); -} - //--------------------------------------------------------------------+ // API: SPI transfer with MAX3421E, must be implemented by application //--------------------------------------------------------------------+ -bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, - uint8_t * rx_buf, size_t rx_len, bool keep_cs) { +void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { (void) rhport; + nrf_gpio_pin_write(MAX3421E_CS_PIN, active ? 0 : 1); +} - max3421e_cs_assert(true); +bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len) { + (void) rhport; nrfx_spim_xfer_desc_t xfer = { .p_tx_buffer = tx_buf, @@ -123,11 +121,7 @@ bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx .rx_length = rx_len, }; - bool ret = (nrfx_spim_xfer(&_spi, &xfer, 0) == NRFX_SUCCESS); - - if ( !keep_cs ) max3421e_cs_assert(false); - - return ret; + return (nrfx_spim_xfer(&_spi, &xfer, 0) == NRFX_SUCCESS); } #endif @@ -218,10 +212,10 @@ void board_init(void) { if ( usb_reg & OUTPUTRDY_Msk ) tusb_hal_nrf_power_event(USB_EVT_READY); #endif -#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E +#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 // manually manage CS nrf_gpio_cfg_output(MAX3421E_CS_PIN); - max3421e_cs_assert(false); + tuh_max3421_spi_cs_api(0, false); // USB host using max3421e usb controller via SPI nrfx_spim_config_t cfg = { diff --git a/hw/bsp/nrf/family.cmake b/hw/bsp/nrf/family.cmake index 8bf7bcb52..ff6b882ce 100644 --- a/hw/bsp/nrf/family.cmake +++ b/hw/bsp/nrf/family.cmake @@ -124,7 +124,7 @@ function(family_configure_example TARGET RTOS) family_add_tinyusb(${TARGET} OPT_MCU_NRF5X ${RTOS}) target_sources(${TARGET}-tinyusb PUBLIC ${TOP}/src/portable/nordic/nrf5x/dcd_nrf5x.c - ${TOP}/src/portable/analog/max3421e/hcd_max3421e.c + ${TOP}/src/portable/analog/max3421/hcd_max3421.c ) target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) diff --git a/src/host/hcd.h b/src/host/hcd.h index 079877b79..1f01a1a2f 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -170,7 +170,7 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr); bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc); // Submit a transfer, when complete hcd_event_xfer_complete() must be invoked -bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen); +bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen); // Abort a queued transfer. Note: it can only abort transfer that has not been started // Return true if a queued transfer is aborted, false if there is no transfer to abort diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c new file mode 100644 index 000000000..edcb6ca6f --- /dev/null +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -0,0 +1,613 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "tusb_option.h" + +#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 + +#include "host/hcd.h" + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +// Command format is +// Reg [7:3] | 0 [2] | Dir [1] | Ack [0] + +enum { + CMDBYTE_WRITE = 0x02, +}; + +enum { + RCVVFIFO_ADDR = 1u << 3, // 0x08 + SNDFIFO_ADDR = 2u << 3, // 0x10 + SUDFIFO_ADDR = 4u << 3, // 0x20 + RCVBC_ADDR = 6u << 3, // 0x30 + SNDBC_ADDR = 7u << 3, // 0x38 + USBIRQ_ADDR = 13u << 3, // 0x68 + USBIEN_ADDR = 14u << 3, // 0x70 + USBCTL_ADDR = 15u << 3, // 0x78 + CPUCTL_ADDR = 16u << 3, // 0x80 + PINCTL_ADDR = 17u << 3, // 0x88 + REVISION_ADDR = 18u << 3, // 0x90 + HIRQ_ADDR = 25u << 3, // 0xC8 + HIEN_ADDR = 26u << 3, // 0xD0 + MODE_ADDR = 27u << 3, // 0xD8 + PERADDR_ADDR = 28u << 3, // 0xE0 + HCTL_ADDR = 29u << 3, // 0xE8 + HXFR_ADDR = 30u << 3, // 0xF0 + HRSL_ADDR = 31u << 3, // 0xF8 +}; + +enum { + USBIRQ_OSCOK_IRQ = 1u << 0, + USBIRQ_NOVBUS_IRQ = 1u << 5, + USBIRQ_VBUS_IRQ = 1u << 6, +}; + +enum { + USBCTL_PWRDOWN = 1u << 4, + USBCTL_CHIPRES = 1u << 5, +}; + +enum { + CPUCTL_IE = 1u << 0, + CPUCTL_PULSEWID0 = 1u << 6, + CPUCTL_PULSEWID1 = 1u << 7, +}; + +enum { + PINCTL_GPXA = 1u << 0, + PINCTL_GPXB = 1u << 1, + PINCTL_POSINT = 1u << 2, + PINCTL_INTLEVEL = 1u << 3, + PINCTL_FDUPSPI = 1u << 4, +}; + +enum { + HIRQ_BUSEVENT_IRQ = 1u << 0, + HIRQ_RWU_IRQ = 1u << 1, + HIRQ_RCVDAV_IRQ = 1u << 2, + HIRQ_SNDBAV_IRQ = 1u << 3, + HIRQ_SUSDN_IRQ = 1u << 4, + HIRQ_CONDET_IRQ = 1u << 5, + HIRQ_FRAME_IRQ = 1u << 6, + HIRQ_HXFRDN_IRQ = 1u << 7, +}; + +enum { + MODE_HOST = 1u << 0, + MODE_LOWSPEED = 1u << 1, + MODE_HUBPRE = 1u << 2, + MODE_SOFKAENAB = 1u << 3, + MODE_SEPIRQ = 1u << 4, + MODE_DELAYISO = 1u << 5, + MODE_DMPULLDN = 1u << 6, + MODE_DPPULLDN = 1u << 7, +}; + +enum { + HCTL_BUSRST = 1u << 0, + HCTL_FRMRST = 1u << 1, + HCTL_SAMPLEBUS = 1u << 2, + HCTL_SIGRSM = 1u << 3, + HCTL_RCVTOG0 = 1u << 4, + HCTL_RCVTOG1 = 1u << 5, + HCTL_SNDTOG0 = 1u << 6, + HCTL_SNDTOG1 = 1u << 7, +}; + +enum { + HXFR_EPNUM_MASK = 0x0f, + HXFR_SETUP = 1u << 4, + HXFR_OUT_NIN = 1u << 5, + HXFR_ISO = 1u << 6, + HXFR_HS = 1u << 7, +}; + +enum { + HRSL_RESULT_MASK = 0x0f, + HRSL_RCVTOGRD = 1u << 4, + HRSL_SNDTOGRD = 1u << 5, + HRSL_KSTATUS = 1u << 6, + HRSL_JSTATUS = 1u << 7, +}; + +enum { + HRSL_SUCCESS = 0, + HRSL_BUSY, + HRSL_BAD_REQ, + HRSL_UNDEF, + HRSL_NAK, + HRSL_STALL, + HRSL_TOG_ERR, + HRSL_WRONG_PID, + HRSL_BAD_BYTECOUNT, + HRSL_PID_ERR, + HRSL_PKT_ERR, + HRSL_CRC_ERR, + HRSL_K_ERR, + HRSL_J_ERR, + HRSL_TIMEOUT, + HRSL_BABBLE, +}; + +enum { + DEFAULT_HIEN = HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ | HIRQ_HXFRDN_IRQ +}; + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +typedef struct { + uint8_t xfer_type; + uint8_t data_toggle; + uint16_t packet_size; + + uint16_t total_len; + uint16_t xferred_len; + uint8_t* buf; +} hcd_ep_t; + +typedef struct { + bool inited; + + // cached register + uint8_t sndbc; + uint8_t mode; + uint8_t peraddr; + uint8_t hxfr; + + volatile uint16_t frame_count; + + hcd_ep_t ep[8][2]; +} max2341_data_t; + +static max2341_data_t _hcd_data; + +//--------------------------------------------------------------------+ +// API: SPI transfer with MAX3421E, must be implemented by application +//--------------------------------------------------------------------+ + +void tuh_max3421_spi_cs_api(uint8_t rhport, bool active); +bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len); + +//void tuh_max3421e_int_enable(uint8_t rhport, bool enabled); + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + +static void fifo_write(uint8_t reg, uint8_t const * buffer, uint16_t len) { + reg |= CMDBYTE_WRITE; + + tuh_max3421_spi_cs_api(0, true); + + tuh_max3421_spi_xfer_api(0, ®, 1, NULL, 0); + tuh_max3421_spi_xfer_api(0, buffer, len, NULL, 0); + + tuh_max3421_spi_cs_api(0, false); +} + +// return HIRQ register since we are in full-duplex mode +static uint8_t reg_write(uint8_t reg, uint8_t data) { + uint8_t tx_buf[2] = {reg | CMDBYTE_WRITE, data}; + uint8_t rx_buf[2] = {0, 0}; + + tuh_max3421_spi_cs_api(0, true); + tuh_max3421_spi_xfer_api(0, tx_buf, 2, rx_buf, 2); + tuh_max3421_spi_cs_api(0, false); + + TU_LOG2("HIRQ: %02X\r\n", rx_buf[0]); + return rx_buf[0]; +} + +static uint8_t reg_read(uint8_t reg) { + uint8_t tx_buf[2] = {reg, 0}; + uint8_t rx_buf[2] = {0, 0}; + + tuh_max3421_spi_cs_api(0, true); + bool ret = tuh_max3421_spi_xfer_api(0, tx_buf, 2, rx_buf, 2); + tuh_max3421_spi_cs_api(0, false); + + return ret ? rx_buf[1] : 0; +} + +static inline uint8_t mode_write(uint8_t data) { + _hcd_data.mode = data; + return reg_write(MODE_ADDR, data); +} + +static inline uint8_t peraddr_write(uint8_t data) { + if ( _hcd_data.peraddr == data ) return 0; // no need to change address + + _hcd_data.peraddr = data; + return reg_write(PERADDR_ADDR, data); +} + +static inline uint8_t hxfr_write(uint8_t data) { + _hcd_data.hxfr = data; + return reg_write(HXFR_ADDR, data); +} + +static inline uint8_t sndbc_write(uint8_t data) { + _hcd_data.sndbc = data; + return reg_write(SNDBC_ADDR, data); +} + + +//--------------------------------------------------------------------+ +// Controller API +//--------------------------------------------------------------------+ + +// optional hcd configuration, called by tuh_configure() +bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { + (void) rhport; + (void) cfg_id; + (void) cfg_param; + + return false; +} + +tusb_speed_t handle_connect_irq(uint8_t rhport) { + (void) rhport; + + uint8_t const hrsl = reg_read(HRSL_ADDR); + uint8_t const jk = hrsl & (HRSL_JSTATUS | HRSL_KSTATUS); + + tusb_speed_t speed; + uint8_t new_mode = MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST; + + switch(jk) { + case 0x00: + // SEO is disconnected + speed = TUSB_SPEED_INVALID; + break; + + case (HRSL_JSTATUS | HRSL_KSTATUS): + // SE1 is illegal + speed = TUSB_SPEED_INVALID; + break; + + default: { + // Low speed if (LS = 1 and J-state) or (LS = 0 and K-State) + uint8_t const mode = reg_read(MODE_ADDR); + uint8_t const ls_bit = mode & MODE_LOWSPEED; + + if ( (ls_bit && (jk == HRSL_JSTATUS)) || (!ls_bit && (jk == HRSL_KSTATUS)) ) { + speed = TUSB_SPEED_LOW; + new_mode |= MODE_LOWSPEED; + } else { + speed = TUSB_SPEED_FULL; + } + + new_mode |= MODE_SOFKAENAB; // enable SOF since there is new device + + break; + } + } + + mode_write(new_mode); + TU_LOG2_INT(speed); + return speed; +} + +// Initialize controller to host mode +bool hcd_init(uint8_t rhport) { + (void) rhport; + + tu_memclr(&_hcd_data, sizeof(_hcd_data)); + + // full duplex, interrupt negative edge + reg_write(PINCTL_ADDR, PINCTL_FDUPSPI); + + // reset + reg_write(USBCTL_ADDR, USBCTL_CHIPRES); + reg_write(USBCTL_ADDR, 0); + while( !(reg_read(USBIRQ_ADDR) & USBIRQ_OSCOK_IRQ) ) { + // wait for oscillator to stabilize + } + + // Mode: Host and DP/DM pull down + mode_write(MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST); + + // bus reset, this will trigger CONDET IRQ if device is already connected + reg_write(HCTL_ADDR, HCTL_BUSRST); + + // clear all previously pending IRQ + reg_write(HIRQ_ADDR, 0xff); + + _hcd_data.inited = true; + + // Enable Connection IRQ + reg_write(HIEN_ADDR, DEFAULT_HIEN); + + // Enable Interrupt pin + reg_write(CPUCTL_ADDR, CPUCTL_IE); + + return true; +} + +// Enable USB interrupt +void hcd_int_enable (uint8_t rhport) { + (void) rhport; +} + +// Disable USB interrupt +void hcd_int_disable(uint8_t rhport) { + (void) rhport; +} + +// Get frame number (1ms) +uint32_t hcd_frame_number(uint8_t rhport) { + (void) rhport; + return (uint32_t ) _hcd_data.frame_count; +} + +//--------------------------------------------------------------------+ +// Port API +//--------------------------------------------------------------------+ + +// Get the current connect status of roothub port +bool hcd_port_connect_status(uint8_t rhport) { + (void) rhport; + return (_hcd_data.mode & MODE_SOFKAENAB) ? true : false; +} + +// Reset USB bus on the port. Return immediately, bus reset sequence may not be complete. +// Some port would require hcd_port_reset_end() to be invoked after 10ms to complete the reset sequence. +void hcd_port_reset(uint8_t rhport) { + (void) rhport; + // Bus reset will also trigger CONDET IRQ, disable it + uint8_t hien = DEFAULT_HIEN & ~HIRQ_CONDET_IRQ; + reg_write(HIEN_ADDR, hien); + + reg_write(HCTL_ADDR, HCTL_BUSRST); +} + +// Complete bus reset sequence, may be required by some controllers +void hcd_port_reset_end(uint8_t rhport) { + (void) rhport; + reg_write(HCTL_ADDR, 0); + + // Bus reset will also trigger CONDET IRQ, clear and re-enable it after reset + reg_write(HIRQ_ADDR, HIRQ_CONDET_IRQ); + reg_write(HIEN_ADDR, DEFAULT_HIEN); +} + +// Get port link speed +tusb_speed_t hcd_port_speed_get(uint8_t rhport) { + (void) rhport; + return (_hcd_data.mode & MODE_LOWSPEED) ? TUSB_SPEED_LOW : TUSB_SPEED_FULL; +} + +// HCD closes all opened endpoints belong to this device +void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { + (void) rhport; + (void) dev_addr; +} + +//--------------------------------------------------------------------+ +// Endpoints API +//--------------------------------------------------------------------+ + +// Open an endpoint +bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc) { + (void) rhport; + (void) dev_addr; + (void) ep_desc; + + uint8_t ep_num = tu_edpt_number(ep_desc->bEndpointAddress); + uint8_t ep_dir = tu_edpt_dir(ep_desc->bEndpointAddress); + + _hcd_data.ep[ep_num][ep_dir].packet_size = tu_edpt_packet_size(ep_desc); + + return true; +} + +// Submit a transfer, when complete hcd_event_xfer_complete() must be invoked +bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { + (void) rhport; + + uint8_t const ep_num = tu_edpt_number(ep_addr); + uint8_t const ep_dir = tu_edpt_dir(ep_addr); + + hcd_ep_t* ep = &_hcd_data.ep[ep_num][ep_dir]; + + ep->buf = buffer; + ep->total_len = buflen; + ep->xferred_len = 0; + + uint8_t hirq = peraddr_write(daddr); + + uint8_t hctl = 0; + uint8_t hxfr = ep_num; + if ( ep_num == 0 ) { + ep->data_toggle = 1; + if ( buffer == NULL || buflen == 0 ) { + // ZLP for ACK stage + hxfr |= HXFR_HS; + } + } else if ( ep->xfer_type == TUSB_XFER_ISOCHRONOUS ) { + hxfr |= HXFR_ISO; + } + + if ( 0 == ep_dir ) { + // Page 12: Programming BULK-OUT Transfers + TU_ASSERT(hirq & HIRQ_RCVDAV_IRQ); + + uint8_t const xact_len = (uint8_t) tu_min16(buflen, ep->packet_size); + fifo_write(SNDFIFO_ADDR, buffer, xact_len); + reg_write(SNDBC_ADDR, xact_len); + + hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); + hxfr |= HXFR_OUT_NIN; + } else { + // Page 13: Programming BULK-IN Transfers + hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); + } + + reg_write(HCTL_ADDR, hctl); + hxfr_write(hxfr); + + return true; +} + +// Abort a queued transfer. Note: it can only abort transfer that has not been started +// Return true if a queued transfer is aborted, false if there is no transfer to abort +bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + + return false; +} + +// Submit a special transfer to send 8-byte Setup Packet, when complete hcd_event_xfer_complete() must be invoked +bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8]) { + (void) rhport; + + hcd_ep_t* ep = &_hcd_data.ep[0][0]; + ep->total_len = 8; + ep->xferred_len = 0; + + peraddr_write(daddr); + fifo_write(SUDFIFO_ADDR, setup_packet, 8); + hxfr_write(HXFR_SETUP); + + return true; +} + +// clear stall, data toggle is also reset to DATA0 +bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { + (void) rhport; + (void) dev_addr; + (void) ep_addr; + + return false; +} + +static void handle_xfer_done(uint8_t rhport) { + (void) rhport; + + uint8_t const hrsl = reg_read(HRSL_ADDR); + uint8_t const result = hrsl & HRSL_RESULT_MASK; + uint8_t xfer_result; + + TU_LOG3("HRSL: %02X\r\n", hrsl); + switch(result) { + case HRSL_SUCCESS: + xfer_result = XFER_RESULT_SUCCESS; + break; + + case HRSL_STALL: + xfer_result = XFER_RESULT_STALLED; + break; + + case HRSL_BAD_REQ: + // occurred when initialized without any pending transfer. Skip for now + return; + + default: + xfer_result = XFER_RESULT_FAILED; + break; + } + + uint8_t ep_dir = 0; + uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; + uint8_t const xfer_type = _hcd_data.hxfr & 0xf0; + + hcd_ep_t * ep; + + if ( (xfer_type & HXFR_SETUP) || (xfer_type & HXFR_OUT_NIN) ) { + // SETUP or OUT transfer + ep_dir = 0; + ep = &_hcd_data.ep[ep_num][ep_dir]; + + uint8_t const xact_len = (xfer_type & HXFR_SETUP) ? 8 : _hcd_data.sndbc; + ep->xferred_len += xact_len; + + if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { + hcd_event_xfer_complete(_hcd_data.peraddr, ep_num, ep->xferred_len, xfer_result, true); + }else { + // more to transfer + } + } else { + // IN transfer + ep_dir = 1; + ep = &_hcd_data.ep[ep_num][ep_dir]; + uint8_t const xact_len = reg_read(RCVBC_ADDR); + ep->xferred_len += xact_len; + + // short packet or all bytes transferred + if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { + hcd_event_xfer_complete(_hcd_data.peraddr, TUSB_DIR_IN_MASK | ep_num, ep->xferred_len, xfer_result, true); + }else { + // more to transfer + } + } +} + +// Interrupt Handler +void hcd_int_handler(uint8_t rhport) { + // not initialized, do nothing + if ( !_hcd_data.inited ) return; + + uint8_t hirq = reg_read(HIRQ_ADDR); + TU_LOG3_HEX(hirq); + + if (hirq & HIRQ_FRAME_IRQ) { + _hcd_data.frame_count++; + } + + if (hirq & HIRQ_CONDET_IRQ) { + tusb_speed_t speed = handle_connect_irq(rhport); + + if (speed == TUSB_SPEED_INVALID) { + hcd_event_device_remove(rhport, true); + }else { + hcd_event_device_attach(rhport, true); + } + } + + if (hirq & HIRQ_HXFRDN_IRQ) { + handle_xfer_done(rhport); + } + + if ( hirq & HIRQ_RCVDAV_IRQ ) { + TU_LOG3("RCVDAV\r\n"); + TU_LOG3_INT(reg_read(RCVBC_ADDR)); + } + + // clear all interrupt execept SNDBAV_IRQ + hirq &= ~HIRQ_SNDBAV_IRQ; + if ( hirq ) { + reg_write(HIRQ_ADDR, hirq); + } +} + +#endif diff --git a/src/portable/analog/max3421e/hcd_max3421e.c b/src/portable/analog/max3421e/hcd_max3421e.c deleted file mode 100644 index c9596f695..000000000 --- a/src/portable/analog/max3421e/hcd_max3421e.c +++ /dev/null @@ -1,503 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2023 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "tusb_option.h" - -#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421E) && CFG_TUH_MAX3421E - -#include "host/hcd.h" - -//--------------------------------------------------------------------+ -// -//--------------------------------------------------------------------+ - -// Command format is -// Reg [7:3] | 0 [2] | Dir [1] | Ack [0] - -enum { - CMDBYTE_WRITE = 0x02, -}; - -enum { - RCVVFIFO_ADDR = 1u << 3, // 0x08 - SNDFIFO_ADDR = 2u << 3, // 0x10 - SUDFIFO_ADDR = 4u << 3, // 0x20 - RCVBC_ADDR = 6u << 3, // 0x30 - SNDBC_ADDR = 7u << 3, // 0x38 - USBIRQ_ADDR = 13u << 3, // 0x68 - USBIEN_ADDR = 14u << 3, // 0x70 - USBCTL_ADDR = 15u << 3, // 0x78 - CPUCTL_ADDR = 16u << 3, // 0x80 - PINCTL_ADDR = 17u << 3, // 0x88 - REVISION_ADDR = 18u << 3, // 0x90 - HIRQ_ADDR = 25u << 3, // 0xC8 - HIEN_ADDR = 26u << 3, // 0xD0 - MODE_ADDR = 27u << 3, // 0xD8 - PERADDR_ADDR = 28u << 3, // 0xE0 - HCTL_ADDR = 29u << 3, // 0xE8 - HXFR_ADDR = 30u << 3, // 0xF0 - HRSL_ADDR = 31u << 3, // 0xF8 -}; - -enum { - USBIRQ_OSCOK_IRQ = 1u << 0, - USBIRQ_NOVBUS_IRQ = 1u << 5, - USBIRQ_VBUS_IRQ = 1u << 6, -}; - -enum { - USBCTL_PWRDOWN = 1u << 4, - USBCTL_CHIPRES = 1u << 5, -}; - -enum { - CPUCTL_IE = 1u << 0, - CPUCTL_PULSEWID0 = 1u << 6, - CPUCTL_PULSEWID1 = 1u << 7, -}; - -enum { - PINCTL_GPXA = 1u << 0, - PINCTL_GPXB = 1u << 1, - PINCTL_POSINT = 1u << 2, - PINCTL_INTLEVEL = 1u << 3, - PINCTL_FDUPSPI = 1u << 4, -}; - -enum { - HIRQ_BUSEVENT_IRQ = 1u << 0, - HIRQ_RWU_IRQ = 1u << 1, - HIRQ_RCVDAV_IRQ = 1u << 2, - HIRQ_SNDBAV_IRQ = 1u << 3, - HIRQ_SUSDN_IRQ = 1u << 4, - HIRQ_CONDET_IRQ = 1u << 5, - HIRQ_FRAME_IRQ = 1u << 6, - HIRQ_HXFRDN_IRQ = 1u << 7, -}; - -enum { - MODE_HOST = 1u << 0, - MODE_LOWSPEED = 1u << 1, - MODE_HUBPRE = 1u << 2, - MODE_SOFKAENAB = 1u << 3, - MODE_SEPIRQ = 1u << 4, - MODE_DELAYISO = 1u << 5, - MODE_DMPULLDN = 1u << 6, - MODE_DPPULLDN = 1u << 7, -}; - -enum { - HCTL_BUSRST = 1u << 1, - HCTL_FRMRST = 1u << 2, - HCTL_SAMPLEBUS = 1u << 3, - HCTL_SIGRSM = 1u << 4, - HCTL_RCVTOG0 = 1u << 5, - HCTL_RCVTOG1 = 1u << 6, - HCTL_SNDTOG0 = 1u << 7, - HCTL_SNDTOG1 = 1u << 8, -}; - -enum { - HXFR_EPNUM_MASK = 0x0f, - HXFR_SETUP = 1u << 4, - HXFR_OUT_NIN = 1u << 5, - HXFR_ISO = 1u << 6, - HXFR_HS = 1u << 7, -}; - -enum { - HRSL_RESULT_MASK = 0x0f, - HRSL_RCVTOGRD = 1u << 4, - HRSL_SNDTOGRD = 1u << 5, - HRSL_KSTATUS = 1u << 6, - HRSL_JSTATUS = 1u << 7, -}; - -enum { - HRSL_SUCCESS = 0, - HRSL_BUSY, - HRSL_BAD_REQ, - HRSL_UNDEF, - HRSL_NAK, - HRSL_STALL, - HRSL_TOG_ERR, - HRSL_WRONG_PID, - HRSL_BAD_BYTECOUNT, - HRSL_PID_ERR, - HRSL_PKT_ERR, - HRSL_CRC_ERR, - HRSL_K_ERR, - HRSL_J_ERR, - HRSL_TIMEOUT, - HRSL_BABBLE, -}; - - -//--------------------------------------------------------------------+ -// -//--------------------------------------------------------------------+ - -typedef struct { - // cached register - uint8_t mode; - uint8_t peraddr; - uint8_t hxfr; - - volatile uint16_t frame_count; - - struct { - uint16_t packet_size; - uint16_t total_len; - uint8_t xfer_type; - }ep[8][2]; -} max2341e_data_t; - -static max2341e_data_t _hcd_data; - -//--------------------------------------------------------------------+ -// API: SPI transfer with MAX3421E, must be implemented by application -//--------------------------------------------------------------------+ - -bool tuh_max3421e_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, - uint8_t * rx_buf, size_t rx_len, bool keep_cs); -//void tuh_max3421e_int_enable(uint8_t rhport, bool enabled); - -//--------------------------------------------------------------------+ -// -//--------------------------------------------------------------------+ - -// return HIRQ register since we are in full-duplex mode -static uint8_t reg_write(uint8_t reg, uint8_t data) { - uint8_t tx_buf[2] = {reg | CMDBYTE_WRITE, data}; - uint8_t rx_buf[2] = {0, 0}; - tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2, false); - TU_LOG2("HIRQ: %02X\r\n", rx_buf[0]); - return rx_buf[0]; -} - -static uint8_t reg_read(uint8_t reg) { - uint8_t tx_buf[2] = {reg, 0}; - uint8_t rx_buf[2] = {0, 0}; - return tuh_max3421e_spi_xfer_api(0, tx_buf, 2, rx_buf, 2, false) ? rx_buf[1] : 0; -} - -static inline uint8_t mode_write(uint8_t data) { - _hcd_data.mode = data; - return reg_write(MODE_ADDR, data); -} - -static inline uint8_t peraddr_write(uint8_t data) { - if ( _hcd_data.peraddr == data ) return 0; // no need to change address - - _hcd_data.peraddr = data; - return reg_write(PERADDR_ADDR, data); -} - -static inline uint8_t hxfr_write(uint8_t data) { - _hcd_data.hxfr = data; - return reg_write(HXFR_ADDR, data); -} - -static void fifo_write(uint8_t reg, uint8_t const * buffer, uint16_t len) { - uint8_t tx_buf[1] = {reg | CMDBYTE_WRITE}; - tuh_max3421e_spi_xfer_api(0, tx_buf, 1, NULL, 0, true); - tuh_max3421e_spi_xfer_api(0, buffer, len, NULL, 0, false); -} - - -//--------------------------------------------------------------------+ -// Controller API -//--------------------------------------------------------------------+ - -// optional hcd configuration, called by tuh_configure() -bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { - (void) rhport; - (void) cfg_id; - (void) cfg_param; - - return false; -} - -tusb_speed_t handle_connect_irq(uint8_t rhport) { - (void) rhport; - - uint8_t const hrsl = reg_read(HRSL_ADDR); - uint8_t const jk = hrsl & (HRSL_JSTATUS | HRSL_KSTATUS); - - tusb_speed_t speed; - uint8_t new_mode = MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST; - - switch(jk) { - case 0x00: - // SEO is disconnected - speed = TUSB_SPEED_INVALID; - break; - - case (HRSL_JSTATUS | HRSL_KSTATUS): - // SE1 is illegal - speed = TUSB_SPEED_INVALID; - break; - - default: { - // Low speed if (LS = 1 and J-state) or (LS = 0 and K-State) - uint8_t const mode = reg_read(MODE_ADDR); - uint8_t const ls_bit = mode & MODE_LOWSPEED; - - if ( (ls_bit && (jk == HRSL_JSTATUS)) || (!ls_bit && (jk == HRSL_KSTATUS)) ) { - speed = TUSB_SPEED_LOW; - new_mode |= MODE_LOWSPEED; - } else { - speed = TUSB_SPEED_FULL; - } - - new_mode |= MODE_SOFKAENAB; // enable SOF since there is new device - - break; - } - } - - mode_write(new_mode); - TU_LOG2_INT(speed); - return speed; -} - -// Initialize controller to host mode -bool hcd_init(uint8_t rhport) { - (void) rhport; - - tu_memclr(&_hcd_data, sizeof(_hcd_data)); - - // full duplex, interrupt level (should be configurable) - reg_write(PINCTL_ADDR, PINCTL_FDUPSPI | PINCTL_INTLEVEL); - - // reset - reg_write(USBCTL_ADDR, USBCTL_CHIPRES); - reg_write(USBCTL_ADDR, 0); - while( !(reg_read(USBIRQ_ADDR) & USBIRQ_OSCOK_IRQ) ) { - // wait for oscillator to stabilize - } - - // Mode: Host and DP/DM pull down - mode_write(MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST); - - // Enable Connection IRQ - reg_write(HIEN_ADDR, HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ | HIRQ_HXFRDN_IRQ); - - #if 0 - // Note: if device is already connected, CONDET IRQ may not be triggered. - // We need to detect it by sampling bus signal. FIXME not working - reg_write(HCTL_ADDR, HCTL_SAMPLEBUS); - while ( reg_read(HCTL_ADDR) & HCTL_SAMPLEBUS ) {} - - if ( TUSB_SPEED_INVALID != handle_connect_irq(rhport) ) { - reg_write(HIRQ_ADDR, HIRQ_CONDET_IRQ); // clear connect irq - } - #endif - - // Enable Interrupt pin - reg_write(CPUCTL_ADDR, CPUCTL_IE); - - return true; -} - -// Enable USB interrupt -void hcd_int_enable (uint8_t rhport) { - (void) rhport; -} - -// Disable USB interrupt -void hcd_int_disable(uint8_t rhport) { - (void) rhport; -} - -// Get frame number (1ms) -uint32_t hcd_frame_number(uint8_t rhport) { - (void) rhport; - return (uint32_t ) _hcd_data.frame_count; -} - -//--------------------------------------------------------------------+ -// Port API -//--------------------------------------------------------------------+ - -// Get the current connect status of roothub port -bool hcd_port_connect_status(uint8_t rhport) { - (void) rhport; - return (_hcd_data.mode & MODE_SOFKAENAB) ? true : false; -} - -// Reset USB bus on the port. Return immediately, bus reset sequence may not be complete. -// Some port would require hcd_port_reset_end() to be invoked after 10ms to complete the reset sequence. -void hcd_port_reset(uint8_t rhport) { - (void) rhport; - reg_write(HCTL_ADDR, HCTL_BUSRST); -} - -// Complete bus reset sequence, may be required by some controllers -void hcd_port_reset_end(uint8_t rhport) { - (void) rhport; - reg_write(HCTL_ADDR, 0); -} - -// Get port link speed -tusb_speed_t hcd_port_speed_get(uint8_t rhport) { - (void) rhport; - return (_hcd_data.mode & MODE_LOWSPEED) ? TUSB_SPEED_LOW : TUSB_SPEED_FULL; -} - -// HCD closes all opened endpoints belong to this device -void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { - (void) rhport; - (void) dev_addr; -} - -//--------------------------------------------------------------------+ -// Endpoints API -//--------------------------------------------------------------------+ - -// Open an endpoint -bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc) { - (void) rhport; - (void) dev_addr; - (void) ep_desc; - - uint8_t ep_num = tu_edpt_number(ep_desc->bEndpointAddress); - uint8_t ep_dir = tu_edpt_dir(ep_desc->bEndpointAddress); - - _hcd_data.ep[ep_num][ep_dir].packet_size = tu_edpt_packet_size(ep_desc); - - return true; -} - -// Submit a transfer, when complete hcd_event_xfer_complete() must be invoked -bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { - (void) rhport; - (void) dev_addr; - (void) ep_addr; - (void) buffer; - (void) buflen; - - return false; -} - -// Abort a queued transfer. Note: it can only abort transfer that has not been started -// Return true if a queued transfer is aborted, false if there is no transfer to abort -bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { - (void) rhport; - (void) dev_addr; - (void) ep_addr; - - return false; -} - -// Submit a special transfer to send 8-byte Setup Packet, when complete hcd_event_xfer_complete() must be invoked -bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8]) { - (void) rhport; - (void) daddr; - (void) setup_packet; - - _hcd_data.ep[0][0].total_len = 8; - - peraddr_write(daddr); - fifo_write(SUDFIFO_ADDR, setup_packet, 8); - hxfr_write(HXFR_SETUP); - - return true; -} - -// clear stall, data toggle is also reset to DATA0 -bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { - (void) rhport; - (void) dev_addr; - (void) ep_addr; - - return false; -} - -// Interrupt Handler -void hcd_int_handler(uint8_t rhport) { - uint8_t hirq = reg_read(HIRQ_ADDR); - TU_LOG3_HEX(hirq); - - if (hirq & HIRQ_CONDET_IRQ) { - tusb_speed_t speed = handle_connect_irq(rhport); - - if (speed == TUSB_SPEED_INVALID) { - hcd_event_device_remove(rhport, true); - }else { - hcd_event_device_attach(rhport, true); - } - } - - if (hirq & HIRQ_FRAME_IRQ) { - _hcd_data.frame_count++; - } - - if (hirq & HIRQ_HXFRDN_IRQ) { - uint8_t const hrsl = reg_read(HRSL_ADDR); - uint8_t const result = hrsl & HRSL_RESULT_MASK; - uint8_t xfer_result; - - TU_LOG3("HRSL: %02X\r\n", hrsl); - switch(result) { - case HRSL_SUCCESS: - xfer_result = XFER_RESULT_SUCCESS; - break; - - case HRSL_STALL: - xfer_result = XFER_RESULT_STALLED; - break; - - default: - xfer_result = XFER_RESULT_FAILED; - break; - } - - uint8_t ep_dir = 0; - uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; - uint8_t const xfer_type = _hcd_data.hxfr & 0xf0; - - if ( xfer_type & HXFR_SETUP ) { - // SETUP transfer - ep_dir = 0; - }else if ( !(xfer_type & HXFR_OUT_NIN) ) { - // IN transfer - ep_dir = 1; - } - - uint8_t const ep_addr = tu_edpt_addr(ep_num, ep_dir); - uint16_t xferred_len = _hcd_data.ep[ep_num][ep_dir].total_len; - - hcd_event_xfer_complete(_hcd_data.peraddr, ep_addr, xferred_len, xfer_result, true); - } - - // clear all interrupt - if ( hirq ) { - reg_write(HIRQ_ADDR, hirq); - } -} - -#endif -- cgit v1.3.1 From 2c237b1ae4b3ffd38fc74df29da63b01348afd1d Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 23 Aug 2023 17:49:28 +0700 Subject: able to complete 1st get device descriptor and set address --- src/portable/analog/max3421/hcd_max3421.c | 180 +++++++++++++++++++++--------- 1 file changed, 126 insertions(+), 54 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index edcb6ca6f..467d7410a 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -156,7 +156,7 @@ enum { }; enum { - DEFAULT_HIEN = HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ | HIRQ_HXFRDN_IRQ + DEFAULT_HIEN = HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ | HIRQ_HXFRDN_IRQ | HIRQ_RCVDAV_IRQ }; //--------------------------------------------------------------------+ @@ -178,6 +178,8 @@ typedef struct { // cached register uint8_t sndbc; + uint8_t hirq; + uint8_t hien; uint8_t mode; uint8_t peraddr; uint8_t hxfr; @@ -203,60 +205,86 @@ bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_ //--------------------------------------------------------------------+ static void fifo_write(uint8_t reg, uint8_t const * buffer, uint16_t len) { + uint8_t const rhport = 0; + uint8_t hirq; reg |= CMDBYTE_WRITE; - tuh_max3421_spi_cs_api(0, true); + tuh_max3421_spi_cs_api(rhport, true); - tuh_max3421_spi_xfer_api(0, ®, 1, NULL, 0); - tuh_max3421_spi_xfer_api(0, buffer, len, NULL, 0); + tuh_max3421_spi_xfer_api(rhport, ®, 1, &hirq, 1); + _hcd_data.hirq = hirq; + tuh_max3421_spi_xfer_api(rhport, buffer, len, NULL, 0); + + tuh_max3421_spi_cs_api(rhport, false); - tuh_max3421_spi_cs_api(0, false); } -// return HIRQ register since we are in full-duplex mode -static uint8_t reg_write(uint8_t reg, uint8_t data) { +static void fifo_read(uint8_t * buffer, uint16_t len) { + uint8_t const rhport = 0; + uint8_t hirq; + uint8_t const reg = RCVVFIFO_ADDR; + + tuh_max3421_spi_cs_api(rhport, true); + + tuh_max3421_spi_xfer_api(rhport, ®, 1, &hirq, 0); + _hcd_data.hirq = hirq; + tuh_max3421_spi_xfer_api(rhport, NULL, 0, buffer, len); + + tuh_max3421_spi_cs_api(rhport, false); +} + +static void reg_write(uint8_t reg, uint8_t data) { + uint8_t const rhport = 0; uint8_t tx_buf[2] = {reg | CMDBYTE_WRITE, data}; uint8_t rx_buf[2] = {0, 0}; - tuh_max3421_spi_cs_api(0, true); - tuh_max3421_spi_xfer_api(0, tx_buf, 2, rx_buf, 2); - tuh_max3421_spi_cs_api(0, false); + tuh_max3421_spi_cs_api(rhport, true); + tuh_max3421_spi_xfer_api(rhport, tx_buf, 2, rx_buf, 2); + tuh_max3421_spi_cs_api(rhport, false); - TU_LOG2("HIRQ: %02X\r\n", rx_buf[0]); - return rx_buf[0]; + // HIRQ register since we are in full-duplex mode + _hcd_data.hirq = rx_buf[0]; + TU_LOG3_HEX(_hcd_data.hirq); } static uint8_t reg_read(uint8_t reg) { + uint8_t const rhport = 0; uint8_t tx_buf[2] = {reg, 0}; uint8_t rx_buf[2] = {0, 0}; - tuh_max3421_spi_cs_api(0, true); - bool ret = tuh_max3421_spi_xfer_api(0, tx_buf, 2, rx_buf, 2); - tuh_max3421_spi_cs_api(0, false); + tuh_max3421_spi_cs_api(rhport, true); + bool ret = tuh_max3421_spi_xfer_api(rhport, tx_buf, 2, rx_buf, 2); + tuh_max3421_spi_cs_api(rhport, false); + _hcd_data.hirq = rx_buf[0]; return ret ? rx_buf[1] : 0; } -static inline uint8_t mode_write(uint8_t data) { +static inline void hien_write(uint8_t data) { + _hcd_data.hien = data; + reg_write(HIEN_ADDR, data); +} + +static inline void mode_write(uint8_t data) { _hcd_data.mode = data; - return reg_write(MODE_ADDR, data); + reg_write(MODE_ADDR, data); } -static inline uint8_t peraddr_write(uint8_t data) { - if ( _hcd_data.peraddr == data ) return 0; // no need to change address +static inline void peraddr_write(uint8_t data) { + if ( _hcd_data.peraddr == data ) return; // no need to change address _hcd_data.peraddr = data; - return reg_write(PERADDR_ADDR, data); + reg_write(PERADDR_ADDR, data); } -static inline uint8_t hxfr_write(uint8_t data) { +static inline void hxfr_write(uint8_t data) { _hcd_data.hxfr = data; - return reg_write(HXFR_ADDR, data); + reg_write(HXFR_ADDR, data); } -static inline uint8_t sndbc_write(uint8_t data) { +static inline void sndbc_write(uint8_t data) { _hcd_data.sndbc = data; - return reg_write(SNDBC_ADDR, data); + reg_write(SNDBC_ADDR, data); } @@ -335,16 +363,16 @@ bool hcd_init(uint8_t rhport) { // Mode: Host and DP/DM pull down mode_write(MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST); - // bus reset, this will trigger CONDET IRQ if device is already connected - reg_write(HCTL_ADDR, HCTL_BUSRST); + // frame reset & bus reset, this will trigger CONDET IRQ if device is already connected + reg_write(HCTL_ADDR, HCTL_BUSRST | HCTL_FRMRST); // clear all previously pending IRQ reg_write(HIRQ_ADDR, 0xff); _hcd_data.inited = true; - // Enable Connection IRQ - reg_write(HIEN_ADDR, DEFAULT_HIEN); + // Enable IRQ + hien_write(DEFAULT_HIEN); // Enable Interrupt pin reg_write(CPUCTL_ADDR, CPUCTL_IE); @@ -383,8 +411,8 @@ bool hcd_port_connect_status(uint8_t rhport) { void hcd_port_reset(uint8_t rhport) { (void) rhport; // Bus reset will also trigger CONDET IRQ, disable it - uint8_t hien = DEFAULT_HIEN & ~HIRQ_CONDET_IRQ; - reg_write(HIEN_ADDR, hien); + uint8_t const hien = DEFAULT_HIEN & ~HIRQ_CONDET_IRQ; + hien_write(hien); reg_write(HCTL_ADDR, HCTL_BUSRST); } @@ -396,7 +424,7 @@ void hcd_port_reset_end(uint8_t rhport) { // Bus reset will also trigger CONDET IRQ, clear and re-enable it after reset reg_write(HIRQ_ADDR, HIRQ_CONDET_IRQ); - reg_write(HIEN_ADDR, DEFAULT_HIEN); + hien_write(DEFAULT_HIEN); } // Get port link speed @@ -426,6 +454,10 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const _hcd_data.ep[ep_num][ep_dir].packet_size = tu_edpt_packet_size(ep_desc); + if (ep_desc->bEndpointAddress == 0) { + _hcd_data.ep[ep_num][1].packet_size = tu_edpt_packet_size(ep_desc); + } + return true; } @@ -442,15 +474,18 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->total_len = buflen; ep->xferred_len = 0; - uint8_t hirq = peraddr_write(daddr); + peraddr_write(daddr); uint8_t hctl = 0; uint8_t hxfr = ep_num; if ( ep_num == 0 ) { ep->data_toggle = 1; if ( buffer == NULL || buflen == 0 ) { - // ZLP for ACK stage + // ZLP for ACK stage, use HS hxfr |= HXFR_HS; + hxfr |= (ep_dir ? 0 : HXFR_OUT_NIN); + hxfr_write(hxfr); + return true; } } else if ( ep->xfer_type == TUSB_XFER_ISOCHRONOUS ) { hxfr |= HXFR_ISO; @@ -458,7 +493,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf if ( 0 == ep_dir ) { // Page 12: Programming BULK-OUT Transfers - TU_ASSERT(hirq & HIRQ_RCVDAV_IRQ); + TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ); uint8_t const xact_len = (uint8_t) tu_min16(buflen, ep->packet_size); fifo_write(SNDFIFO_ADDR, buffer, xact_len); @@ -516,7 +551,7 @@ static void handle_xfer_done(uint8_t rhport) { uint8_t const hrsl = reg_read(HRSL_ADDR); uint8_t const result = hrsl & HRSL_RESULT_MASK; - uint8_t xfer_result; + xfer_result_t xfer_result; TU_LOG3("HRSL: %02X\r\n", hrsl); switch(result) { @@ -537,18 +572,21 @@ static void handle_xfer_done(uint8_t rhport) { break; } - uint8_t ep_dir = 0; uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; uint8_t const xfer_type = _hcd_data.hxfr & 0xf0; - hcd_ep_t * ep; - if ( (xfer_type & HXFR_SETUP) || (xfer_type & HXFR_OUT_NIN) ) { // SETUP or OUT transfer - ep_dir = 0; - ep = &_hcd_data.ep[ep_num][ep_dir]; + hcd_ep_t *ep = &_hcd_data.ep[ep_num][0]; + uint8_t xact_len; + if (xfer_type & HXFR_SETUP) { + xact_len = 8; + } else if ( xfer_type & HXFR_HS ) { + xact_len = 0; + } else { + xact_len = _hcd_data.sndbc; + } - uint8_t const xact_len = (xfer_type & HXFR_SETUP) ? 8 : _hcd_data.sndbc; ep->xferred_len += xact_len; if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { @@ -558,10 +596,27 @@ static void handle_xfer_done(uint8_t rhport) { } } else { // IN transfer - ep_dir = 1; - ep = &_hcd_data.ep[ep_num][ep_dir]; - uint8_t const xact_len = reg_read(RCVBC_ADDR); - ep->xferred_len += xact_len; + hcd_ep_t *ep = &_hcd_data.ep[ep_num][1]; + uint8_t xact_len; + + if ( xfer_type & HXFR_HS ) { + xact_len = 0; + } else { + // RCVDAV_IRQ can trigger 2 times (dual buffered) + while ( _hcd_data.hirq & HIRQ_RCVDAV_IRQ ) { + uint8_t rcvbc = reg_read(RCVBC_ADDR); + xact_len = (uint8_t) tu_min16(rcvbc, ep->total_len - ep->xferred_len); + if ( xact_len ) { + fifo_read(ep->buf, xact_len); + ep->buf += xact_len; + ep->xferred_len += xact_len; + } + + // ack RCVDVAV IRQ + reg_write(HIRQ_ADDR, HIRQ_RCVDAV_IRQ); + _hcd_data.hirq = reg_read(HIRQ_ADDR); + } + } // short packet or all bytes transferred if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { @@ -572,13 +627,35 @@ static void handle_xfer_done(uint8_t rhport) { } } +#if CFG_TUSB_DEBUG >= 3 +void print_hirq(uint8_t hirq) { + TU_LOG3_HEX(hirq); + + if (hirq & HIRQ_HXFRDN_IRQ) TU_LOG3(" HXFRDN"); + if (hirq & HIRQ_FRAME_IRQ) TU_LOG3(" FRAME"); + if (hirq & HIRQ_CONDET_IRQ) TU_LOG3(" CONDET"); + if (hirq & HIRQ_SUSDN_IRQ) TU_LOG3(" SUSDN"); + if (hirq & HIRQ_SNDBAV_IRQ) TU_LOG3(" SNDBAV"); + if (hirq & HIRQ_RCVDAV_IRQ) TU_LOG3(" RCVDAV"); + if (hirq & HIRQ_RWU_IRQ) TU_LOG3(" RWU"); + if (hirq & HIRQ_BUSEVENT_IRQ) TU_LOG3(" BUSEVENT"); + + TU_LOG3("\r\n"); +} + +#else + #define print_hirq(hirq) +#endif + // Interrupt Handler void hcd_int_handler(uint8_t rhport) { // not initialized, do nothing if ( !_hcd_data.inited ) return; - uint8_t hirq = reg_read(HIRQ_ADDR); - TU_LOG3_HEX(hirq); + uint8_t hirq = reg_read(HIRQ_ADDR) & _hcd_data.hien; + if (!hirq) return; + + print_hirq(hirq); if (hirq & HIRQ_FRAME_IRQ) { _hcd_data.frame_count++; @@ -598,13 +675,8 @@ void hcd_int_handler(uint8_t rhport) { handle_xfer_done(rhport); } - if ( hirq & HIRQ_RCVDAV_IRQ ) { - TU_LOG3("RCVDAV\r\n"); - TU_LOG3_INT(reg_read(RCVBC_ADDR)); - } - - // clear all interrupt execept SNDBAV_IRQ - hirq &= ~HIRQ_SNDBAV_IRQ; + // clear all interrupt except SNDBAV_IRQ and RCVDAV_IRQ must be clear after pulling data from FIFO + hirq &= ~ (HIRQ_SNDBAV_IRQ | HIRQ_RCVDAV_IRQ); if ( hirq ) { reg_write(HIRQ_ADDR, hirq); } -- cgit v1.3.1 From 3ed5d6c3724cfa9699d403a76a00f1b04672e2b5 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 24 Aug 2023 16:27:12 +0700 Subject: complete enumeration --- hw/bsp/nrf/family.c | 5 ++- src/portable/analog/max3421/hcd_max3421.c | 68 +++++++++++++++++++------------ 2 files changed, 47 insertions(+), 26 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 45a5166a7..368763b84 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -105,6 +105,10 @@ void max3421e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { //--------------------------------------------------------------------+ // API: SPI transfer with MAX3421E, must be implemented by application //--------------------------------------------------------------------+ +void tuh_max3421e_int_api(uint8_t rhport, bool enabled) { + (void) rhport; + nrfx_gpiote_trigger_enable(MAX3241E_INTR_PIN, enabled); +} void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { (void) rhport; @@ -241,7 +245,6 @@ void board_init(void) { in_config.pull = NRF_GPIO_PIN_PULLUP; nrfx_gpiote_in_init(MAX3241E_INTR_PIN, &in_config, max3421e_int_handler); - nrfx_gpiote_in_event_enable(MAX3241E_INTR_PIN, true); #endif } diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 467d7410a..514cf34b7 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -166,6 +166,7 @@ enum { typedef struct { uint8_t xfer_type; uint8_t data_toggle; + uint8_t xfer_complete; uint16_t packet_size; uint16_t total_len; @@ -244,7 +245,6 @@ static void reg_write(uint8_t reg, uint8_t data) { // HIRQ register since we are in full-duplex mode _hcd_data.hirq = rx_buf[0]; - TU_LOG3_HEX(_hcd_data.hirq); } static uint8_t reg_read(uint8_t reg) { @@ -473,6 +473,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->buf = buffer; ep->total_len = buflen; ep->xferred_len = 0; + ep->xfer_complete = 0; peraddr_write(daddr); @@ -595,34 +596,19 @@ static void handle_xfer_done(uint8_t rhport) { // more to transfer } } else { - // IN transfer + // IN transfer: fifo data is already received in RCVDAV IRQ hcd_ep_t *ep = &_hcd_data.ep[ep_num][1]; - uint8_t xact_len; if ( xfer_type & HXFR_HS ) { - xact_len = 0; - } else { - // RCVDAV_IRQ can trigger 2 times (dual buffered) - while ( _hcd_data.hirq & HIRQ_RCVDAV_IRQ ) { - uint8_t rcvbc = reg_read(RCVBC_ADDR); - xact_len = (uint8_t) tu_min16(rcvbc, ep->total_len - ep->xferred_len); - if ( xact_len ) { - fifo_read(ep->buf, xact_len); - ep->buf += xact_len; - ep->xferred_len += xact_len; - } - - // ack RCVDVAV IRQ - reg_write(HIRQ_ADDR, HIRQ_RCVDAV_IRQ); - _hcd_data.hirq = reg_read(HIRQ_ADDR); - } + ep->xfer_complete = 1; } // short packet or all bytes transferred - if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { + if ( ep->xfer_complete ) { hcd_event_xfer_complete(_hcd_data.peraddr, TUSB_DIR_IN_MASK | ep_num, ep->xferred_len, xfer_result, true); }else { // more to transfer + hxfr_write(_hcd_data.hxfr); } } } @@ -655,7 +641,7 @@ void hcd_int_handler(uint8_t rhport) { uint8_t hirq = reg_read(HIRQ_ADDR) & _hcd_data.hien; if (!hirq) return; - print_hirq(hirq); +// print_hirq(hirq); if (hirq & HIRQ_FRAME_IRQ) { _hcd_data.frame_count++; @@ -671,12 +657,44 @@ void hcd_int_handler(uint8_t rhport) { } } - if (hirq & HIRQ_HXFRDN_IRQ) { - handle_xfer_done(rhport); + // queue more transfer in handle_xfer_done() can cause hirq to be set again while external IRQ may not catch and/or + // not call this handler again. So we need to loop until all IRQ are cleared + while ( hirq & (HIRQ_RCVDAV_IRQ | HIRQ_HXFRDN_IRQ) ) { + if ( hirq & HIRQ_RCVDAV_IRQ ) { + uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; + hcd_ep_t *ep = &_hcd_data.ep[ep_num][1]; + uint8_t xact_len; + + // RCVDAV_IRQ can trigger 2 times (dual buffered) + while ( hirq & HIRQ_RCVDAV_IRQ ) { + uint8_t rcvbc = reg_read(RCVBC_ADDR); + xact_len = (uint8_t) tu_min16(rcvbc, ep->total_len - ep->xferred_len); + if ( xact_len ) { + fifo_read(ep->buf, xact_len); + ep->buf += xact_len; + ep->xferred_len += xact_len; + } + + // ack RCVDVAV IRQ + reg_write(HIRQ_ADDR, HIRQ_RCVDAV_IRQ); + hirq = reg_read(HIRQ_ADDR); + } + + if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { + ep->xfer_complete = 1; + } + } + + if ( hirq & HIRQ_HXFRDN_IRQ ) { + reg_write(HIRQ_ADDR, HIRQ_HXFRDN_IRQ); + handle_xfer_done(rhport); + } + + hirq = reg_read(HIRQ_ADDR); } - // clear all interrupt except SNDBAV_IRQ and RCVDAV_IRQ must be clear after pulling data from FIFO - hirq &= ~ (HIRQ_SNDBAV_IRQ | HIRQ_RCVDAV_IRQ); + // clear all interrupt except SNDBAV_IRQ (never clear by us). Note RCVDAV_IRQ, HXFRDN_IRQ already clear while processing + hirq &= ~HIRQ_SNDBAV_IRQ; if ( hirq ) { reg_write(HIRQ_ADDR, hirq); } -- cgit v1.3.1 From 344932d27e1f65932ce922b639370ecc4fff2153 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 24 Aug 2023 16:27:32 +0700 Subject: add tuh_max3421e_int_api(), retry control if received NAK --- src/portable/analog/max3421/hcd_max3421.c | 60 ++++++++++++++++++++----------- 1 file changed, 40 insertions(+), 20 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 514cf34b7..b4f75e392 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -28,6 +28,7 @@ #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 +#include #include "host/hcd.h" //--------------------------------------------------------------------+ @@ -164,11 +165,15 @@ enum { //--------------------------------------------------------------------+ typedef struct { - uint8_t xfer_type; - uint8_t data_toggle; - uint8_t xfer_complete; uint16_t packet_size; + struct TU_ATTR_PACKED { + uint8_t is_iso : 1; + uint8_t data_toggle : 1; + uint8_t xfer_queued : 1; + uint8_t xfer_complete : 1; + }; + uint16_t total_len; uint16_t xferred_len; uint8_t* buf; @@ -176,6 +181,7 @@ typedef struct { typedef struct { bool inited; + atomic_bool busy; // busy transferring // cached register uint8_t sndbc; @@ -198,8 +204,7 @@ static max2341_data_t _hcd_data; void tuh_max3421_spi_cs_api(uint8_t rhport, bool active); bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len); - -//void tuh_max3421e_int_enable(uint8_t rhport, bool enabled); +void tuh_max3421e_int_api(uint8_t rhport, bool enabled); //--------------------------------------------------------------------+ // @@ -348,6 +353,9 @@ tusb_speed_t handle_connect_irq(uint8_t rhport) { bool hcd_init(uint8_t rhport) { (void) rhport; + TU_LOG2_INT(sizeof(hcd_ep_t)); + TU_LOG2_INT(sizeof(max2341_data_t)); + tu_memclr(&_hcd_data, sizeof(_hcd_data)); // full duplex, interrupt negative edge @@ -382,12 +390,12 @@ bool hcd_init(uint8_t rhport) { // Enable USB interrupt void hcd_int_enable (uint8_t rhport) { - (void) rhport; + tuh_max3421e_int_api(rhport, true); } // Disable USB interrupt void hcd_int_disable(uint8_t rhport) { - (void) rhport; + tuh_max3421e_int_api(rhport, false); } // Get frame number (1ms) @@ -447,17 +455,20 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc) { (void) rhport; (void) dev_addr; - (void) ep_desc; uint8_t ep_num = tu_edpt_number(ep_desc->bEndpointAddress); uint8_t ep_dir = tu_edpt_dir(ep_desc->bEndpointAddress); - _hcd_data.ep[ep_num][ep_dir].packet_size = tu_edpt_packet_size(ep_desc); + hcd_ep_t * ep = &_hcd_data.ep[ep_num][ep_dir]; + + ep->packet_size = tu_edpt_packet_size(ep_desc); if (ep_desc->bEndpointAddress == 0) { - _hcd_data.ep[ep_num][1].packet_size = tu_edpt_packet_size(ep_desc); + _hcd_data.ep[0][1].packet_size = ep->packet_size; } + ep->is_iso = (TUSB_XFER_ISOCHRONOUS == ep_desc->bmAttributes.xfer) ? 1 : 0; + return true; } @@ -474,11 +485,13 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->total_len = buflen; ep->xferred_len = 0; ep->xfer_complete = 0; + ep->xfer_queued = 1; peraddr_write(daddr); uint8_t hctl = 0; uint8_t hxfr = ep_num; + if ( ep_num == 0 ) { ep->data_toggle = 1; if ( buffer == NULL || buflen == 0 ) { @@ -488,7 +501,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf hxfr_write(hxfr); return true; } - } else if ( ep->xfer_type == TUSB_XFER_ISOCHRONOUS ) { + } else if ( ep->is_iso ) { hxfr |= HXFR_ISO; } @@ -551,11 +564,13 @@ static void handle_xfer_done(uint8_t rhport) { (void) rhport; uint8_t const hrsl = reg_read(HRSL_ADDR); - uint8_t const result = hrsl & HRSL_RESULT_MASK; + uint8_t const hresult = hrsl & HRSL_RESULT_MASK; + uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; + xfer_result_t xfer_result; - TU_LOG3("HRSL: %02X\r\n", hrsl); - switch(result) { + //TU_LOG3("HRSL: %02X\r\n", hrsl); + switch(hresult) { case HRSL_SUCCESS: xfer_result = XFER_RESULT_SUCCESS; break; @@ -568,21 +583,26 @@ static void handle_xfer_done(uint8_t rhport) { // occurred when initialized without any pending transfer. Skip for now return; + case HRSL_NAK: + // NAK on control, retry immediately + if (ep_num == 0) hxfr_write(_hcd_data.hxfr); + return; + default: xfer_result = XFER_RESULT_FAILED; break; } - uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; - uint8_t const xfer_type = _hcd_data.hxfr & 0xf0; + uint8_t const hxfr_type = _hcd_data.hxfr & 0xf0; - if ( (xfer_type & HXFR_SETUP) || (xfer_type & HXFR_OUT_NIN) ) { + if ( (hxfr_type & HXFR_SETUP) || (hxfr_type & HXFR_OUT_NIN) ) { // SETUP or OUT transfer hcd_ep_t *ep = &_hcd_data.ep[ep_num][0]; uint8_t xact_len; - if (xfer_type & HXFR_SETUP) { + + if ( hxfr_type & HXFR_SETUP) { xact_len = 8; - } else if ( xfer_type & HXFR_HS ) { + } else if ( hxfr_type & HXFR_HS ) { xact_len = 0; } else { xact_len = _hcd_data.sndbc; @@ -599,7 +619,7 @@ static void handle_xfer_done(uint8_t rhport) { // IN transfer: fifo data is already received in RCVDAV IRQ hcd_ep_t *ep = &_hcd_data.ep[ep_num][1]; - if ( xfer_type & HXFR_HS ) { + if ( hxfr_type & HXFR_HS ) { ep->xfer_complete = 1; } -- cgit v1.3.1 From e6cf125e537125fc7303afc7d0703a3de6b8b334 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 24 Aug 2023 16:46:20 +0700 Subject: save data toggle, always retry NAK. work with msc device --- src/portable/analog/max3421/hcd_max3421.c | 24 +++++++++++++++++++----- 1 file changed, 19 insertions(+), 5 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index b4f75e392..9579409c5 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -492,7 +492,9 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf uint8_t hctl = 0; uint8_t hxfr = ep_num; - if ( ep_num == 0 ) { + if ( ep->is_iso ) { + hxfr |= HXFR_ISO; + } else if ( ep_num == 0 ) { ep->data_toggle = 1; if ( buffer == NULL || buflen == 0 ) { // ZLP for ACK stage, use HS @@ -501,8 +503,6 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf hxfr_write(hxfr); return true; } - } else if ( ep->is_iso ) { - hxfr |= HXFR_ISO; } if ( 0 == ep_dir ) { @@ -511,7 +511,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf uint8_t const xact_len = (uint8_t) tu_min16(buflen, ep->packet_size); fifo_write(SNDFIFO_ADDR, buffer, xact_len); - reg_write(SNDBC_ADDR, xact_len); + sndbc_write(xact_len); hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); hxfr |= HXFR_OUT_NIN; @@ -585,7 +585,10 @@ static void handle_xfer_done(uint8_t rhport) { case HRSL_NAK: // NAK on control, retry immediately - if (ep_num == 0) hxfr_write(_hcd_data.hxfr); + //if (ep_num == 0) + { + hxfr_write(_hcd_data.hxfr); + } return; default: @@ -609,8 +612,14 @@ static void handle_xfer_done(uint8_t rhport) { } ep->xferred_len += xact_len; + ep->buf += xact_len; if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { + if ( ep_num ) { + // save data toggle for non-control + ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; + } + hcd_event_xfer_complete(_hcd_data.peraddr, ep_num, ep->xferred_len, xfer_result, true); }else { // more to transfer @@ -625,6 +634,11 @@ static void handle_xfer_done(uint8_t rhport) { // short packet or all bytes transferred if ( ep->xfer_complete ) { + if ( ep_num ) { + // save data toggle for non-control + ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; + } + hcd_event_xfer_complete(_hcd_data.peraddr, TUSB_DIR_IN_MASK | ep_num, ep->xferred_len, xfer_result, true); }else { // more to transfer -- cgit v1.3.1 From f5ebc1700f4bde1cc166bf5f3d8eb69d8832722a Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 25 Aug 2023 12:12:44 +0700 Subject: add spi lock with interrupt enable/disable --- src/portable/analog/max3421/hcd_max3421.c | 176 +++++++++++++++--------------- 1 file changed, 91 insertions(+), 85 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 9579409c5..0144deca6 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -180,7 +180,6 @@ typedef struct { } hcd_ep_t; typedef struct { - bool inited; atomic_bool busy; // busy transferring // cached register @@ -194,6 +193,8 @@ typedef struct { volatile uint16_t frame_count; hcd_ep_t ep[8][2]; + + OSAL_MUTEX_DEF(spi_mutex); } max2341_data_t; static max2341_data_t _hcd_data; @@ -210,86 +211,106 @@ void tuh_max3421e_int_api(uint8_t rhport, bool enabled); // //--------------------------------------------------------------------+ -static void fifo_write(uint8_t reg, uint8_t const * buffer, uint16_t len) { - uint8_t const rhport = 0; +static void max3421_spi_lock(uint8_t rhport, bool in_isr) { + // disable interrupt and mutex lock (for pre-emptive RTOS) if not in_isr + if (!in_isr) { + tuh_max3421e_int_api(rhport, false); + } + + // assert CS + tuh_max3421_spi_cs_api(rhport, true); +} + +static void max3421_spi_unlock(uint8_t rhport, bool in_isr) { + // de-assert CS + tuh_max3421_spi_cs_api(rhport, false); + + // mutex unlock and re-enable interrupt + if (!in_isr) { + tuh_max3421e_int_api(rhport, true); + } +} + +static void fifo_write(uint8_t rhport, uint8_t reg, uint8_t const * buffer, uint16_t len, bool in_isr) { uint8_t hirq; reg |= CMDBYTE_WRITE; - tuh_max3421_spi_cs_api(rhport, true); + max3421_spi_lock(rhport, in_isr); tuh_max3421_spi_xfer_api(rhport, ®, 1, &hirq, 1); _hcd_data.hirq = hirq; tuh_max3421_spi_xfer_api(rhport, buffer, len, NULL, 0); - tuh_max3421_spi_cs_api(rhport, false); + max3421_spi_unlock(rhport, in_isr); } -static void fifo_read(uint8_t * buffer, uint16_t len) { - uint8_t const rhport = 0; +static void fifo_read(uint8_t rhport, uint8_t * buffer, uint16_t len, bool in_isr) { uint8_t hirq; uint8_t const reg = RCVVFIFO_ADDR; - tuh_max3421_spi_cs_api(rhport, true); + max3421_spi_lock(rhport, in_isr); tuh_max3421_spi_xfer_api(rhport, ®, 1, &hirq, 0); _hcd_data.hirq = hirq; tuh_max3421_spi_xfer_api(rhport, NULL, 0, buffer, len); - tuh_max3421_spi_cs_api(rhport, false); + max3421_spi_unlock(rhport, in_isr); } -static void reg_write(uint8_t reg, uint8_t data) { - uint8_t const rhport = 0; +static void reg_write(uint8_t rhport, uint8_t reg, uint8_t data, bool in_isr) { uint8_t tx_buf[2] = {reg | CMDBYTE_WRITE, data}; uint8_t rx_buf[2] = {0, 0}; - tuh_max3421_spi_cs_api(rhport, true); + max3421_spi_lock(rhport, in_isr); + tuh_max3421_spi_xfer_api(rhport, tx_buf, 2, rx_buf, 2); - tuh_max3421_spi_cs_api(rhport, false); + + max3421_spi_unlock(rhport, in_isr); // HIRQ register since we are in full-duplex mode _hcd_data.hirq = rx_buf[0]; } -static uint8_t reg_read(uint8_t reg) { - uint8_t const rhport = 0; +static uint8_t reg_read(uint8_t rhport, uint8_t reg, bool in_isr) { uint8_t tx_buf[2] = {reg, 0}; uint8_t rx_buf[2] = {0, 0}; - tuh_max3421_spi_cs_api(rhport, true); + max3421_spi_lock(rhport, in_isr); + bool ret = tuh_max3421_spi_xfer_api(rhport, tx_buf, 2, rx_buf, 2); - tuh_max3421_spi_cs_api(rhport, false); + + max3421_spi_unlock(rhport, in_isr); _hcd_data.hirq = rx_buf[0]; return ret ? rx_buf[1] : 0; } -static inline void hien_write(uint8_t data) { +static inline void hien_write(uint8_t rhport, uint8_t data, bool in_isr) { _hcd_data.hien = data; - reg_write(HIEN_ADDR, data); + reg_write(rhport, HIEN_ADDR, data, in_isr); } -static inline void mode_write(uint8_t data) { +static inline void mode_write(uint8_t rhport, uint8_t data, bool in_isr) { _hcd_data.mode = data; - reg_write(MODE_ADDR, data); + reg_write(rhport, MODE_ADDR, data, in_isr); } -static inline void peraddr_write(uint8_t data) { +static inline void peraddr_write(uint8_t rhport, uint8_t data, bool in_isr) { if ( _hcd_data.peraddr == data ) return; // no need to change address _hcd_data.peraddr = data; - reg_write(PERADDR_ADDR, data); + reg_write(rhport, PERADDR_ADDR, data, in_isr); } -static inline void hxfr_write(uint8_t data) { +static inline void hxfr_write(uint8_t rhport, uint8_t data, bool in_isr) { _hcd_data.hxfr = data; - reg_write(HXFR_ADDR, data); + reg_write(rhport, HXFR_ADDR, data, in_isr); } -static inline void sndbc_write(uint8_t data) { +static inline void sndbc_write(uint8_t rhport, uint8_t data, bool in_isr) { _hcd_data.sndbc = data; - reg_write(SNDBC_ADDR, data); + reg_write(rhport, SNDBC_ADDR, data, in_isr); } @@ -307,9 +328,7 @@ bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { } tusb_speed_t handle_connect_irq(uint8_t rhport) { - (void) rhport; - - uint8_t const hrsl = reg_read(HRSL_ADDR); + uint8_t const hrsl = reg_read(rhport, HRSL_ADDR, true); uint8_t const jk = hrsl & (HRSL_JSTATUS | HRSL_KSTATUS); tusb_speed_t speed; @@ -328,7 +347,7 @@ tusb_speed_t handle_connect_irq(uint8_t rhport) { default: { // Low speed if (LS = 1 and J-state) or (LS = 0 and K-State) - uint8_t const mode = reg_read(MODE_ADDR); + uint8_t const mode = reg_read(rhport, MODE_ADDR, true); uint8_t const ls_bit = mode & MODE_LOWSPEED; if ( (ls_bit && (jk == HRSL_JSTATUS)) || (!ls_bit && (jk == HRSL_KSTATUS)) ) { @@ -344,7 +363,7 @@ tusb_speed_t handle_connect_irq(uint8_t rhport) { } } - mode_write(new_mode); + mode_write(rhport, new_mode, true); TU_LOG2_INT(speed); return speed; } @@ -358,32 +377,32 @@ bool hcd_init(uint8_t rhport) { tu_memclr(&_hcd_data, sizeof(_hcd_data)); + hcd_int_disable(rhport); + // full duplex, interrupt negative edge - reg_write(PINCTL_ADDR, PINCTL_FDUPSPI); + reg_write(rhport, PINCTL_ADDR, PINCTL_FDUPSPI, false); // reset - reg_write(USBCTL_ADDR, USBCTL_CHIPRES); - reg_write(USBCTL_ADDR, 0); - while( !(reg_read(USBIRQ_ADDR) & USBIRQ_OSCOK_IRQ) ) { + reg_write(rhport, USBCTL_ADDR, USBCTL_CHIPRES, false); + reg_write(rhport, USBCTL_ADDR, 0, false); + while( !(reg_read(rhport, USBIRQ_ADDR, false) & USBIRQ_OSCOK_IRQ) ) { // wait for oscillator to stabilize } // Mode: Host and DP/DM pull down - mode_write(MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST); + mode_write(rhport, MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST, false); // frame reset & bus reset, this will trigger CONDET IRQ if device is already connected - reg_write(HCTL_ADDR, HCTL_BUSRST | HCTL_FRMRST); + reg_write(rhport, HCTL_ADDR, HCTL_BUSRST | HCTL_FRMRST, false); // clear all previously pending IRQ - reg_write(HIRQ_ADDR, 0xff); - - _hcd_data.inited = true; + reg_write(rhport, HIRQ_ADDR, 0xff, false); // Enable IRQ - hien_write(DEFAULT_HIEN); + hien_write(rhport, DEFAULT_HIEN, false); // Enable Interrupt pin - reg_write(CPUCTL_ADDR, CPUCTL_IE); + reg_write(rhport, CPUCTL_ADDR, CPUCTL_IE, false); return true; } @@ -417,22 +436,20 @@ bool hcd_port_connect_status(uint8_t rhport) { // Reset USB bus on the port. Return immediately, bus reset sequence may not be complete. // Some port would require hcd_port_reset_end() to be invoked after 10ms to complete the reset sequence. void hcd_port_reset(uint8_t rhport) { - (void) rhport; // Bus reset will also trigger CONDET IRQ, disable it uint8_t const hien = DEFAULT_HIEN & ~HIRQ_CONDET_IRQ; - hien_write(hien); + hien_write(rhport, hien, false); - reg_write(HCTL_ADDR, HCTL_BUSRST); + reg_write(rhport, HCTL_ADDR, HCTL_BUSRST, false); } // Complete bus reset sequence, may be required by some controllers void hcd_port_reset_end(uint8_t rhport) { - (void) rhport; - reg_write(HCTL_ADDR, 0); + reg_write(rhport, HCTL_ADDR, 0, false); // Bus reset will also trigger CONDET IRQ, clear and re-enable it after reset - reg_write(HIRQ_ADDR, HIRQ_CONDET_IRQ); - hien_write(DEFAULT_HIEN); + reg_write(rhport, HIRQ_ADDR, HIRQ_CONDET_IRQ, false); + hien_write(rhport, DEFAULT_HIEN, false); } // Get port link speed @@ -487,7 +504,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->xfer_complete = 0; ep->xfer_queued = 1; - peraddr_write(daddr); + peraddr_write(rhport, daddr, false); uint8_t hctl = 0; uint8_t hxfr = ep_num; @@ -500,7 +517,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf // ZLP for ACK stage, use HS hxfr |= HXFR_HS; hxfr |= (ep_dir ? 0 : HXFR_OUT_NIN); - hxfr_write(hxfr); + hxfr_write(rhport, hxfr, false); return true; } } @@ -510,8 +527,8 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ); uint8_t const xact_len = (uint8_t) tu_min16(buflen, ep->packet_size); - fifo_write(SNDFIFO_ADDR, buffer, xact_len); - sndbc_write(xact_len); + fifo_write(rhport, SNDFIFO_ADDR, buffer, xact_len, false); + sndbc_write(rhport, xact_len, false); hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); hxfr |= HXFR_OUT_NIN; @@ -520,8 +537,8 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); } - reg_write(HCTL_ADDR, hctl); - hxfr_write(hxfr); + reg_write(rhport, HCTL_ADDR, hctl, false); + hxfr_write(rhport, hxfr, false); return true; } @@ -544,9 +561,9 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] ep->total_len = 8; ep->xferred_len = 0; - peraddr_write(daddr); - fifo_write(SUDFIFO_ADDR, setup_packet, 8); - hxfr_write(HXFR_SETUP); + peraddr_write(rhport, daddr, false); + fifo_write(rhport, SUDFIFO_ADDR, setup_packet, 8, false); + hxfr_write(rhport, HXFR_SETUP, false); return true; } @@ -561,9 +578,7 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { } static void handle_xfer_done(uint8_t rhport) { - (void) rhport; - - uint8_t const hrsl = reg_read(HRSL_ADDR); + uint8_t const hrsl = reg_read(rhport, HRSL_ADDR, true); uint8_t const hresult = hrsl & HRSL_RESULT_MASK; uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; @@ -587,7 +602,7 @@ static void handle_xfer_done(uint8_t rhport) { // NAK on control, retry immediately //if (ep_num == 0) { - hxfr_write(_hcd_data.hxfr); + hxfr_write(rhport, _hcd_data.hxfr, true); } return; @@ -615,11 +630,8 @@ static void handle_xfer_done(uint8_t rhport) { ep->buf += xact_len; if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { - if ( ep_num ) { - // save data toggle for non-control - ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; - } - + // save data toggle + ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; hcd_event_xfer_complete(_hcd_data.peraddr, ep_num, ep->xferred_len, xfer_result, true); }else { // more to transfer @@ -634,15 +646,12 @@ static void handle_xfer_done(uint8_t rhport) { // short packet or all bytes transferred if ( ep->xfer_complete ) { - if ( ep_num ) { - // save data toggle for non-control - ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; - } - + // save data toggle + ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; hcd_event_xfer_complete(_hcd_data.peraddr, TUSB_DIR_IN_MASK | ep_num, ep->xferred_len, xfer_result, true); }else { // more to transfer - hxfr_write(_hcd_data.hxfr); + hxfr_write(rhport, _hcd_data.hxfr, true); } } } @@ -669,10 +678,7 @@ void print_hirq(uint8_t hirq) { // Interrupt Handler void hcd_int_handler(uint8_t rhport) { - // not initialized, do nothing - if ( !_hcd_data.inited ) return; - - uint8_t hirq = reg_read(HIRQ_ADDR) & _hcd_data.hien; + uint8_t hirq = reg_read(rhport, HIRQ_ADDR, true) & _hcd_data.hien; if (!hirq) return; // print_hirq(hirq); @@ -701,17 +707,17 @@ void hcd_int_handler(uint8_t rhport) { // RCVDAV_IRQ can trigger 2 times (dual buffered) while ( hirq & HIRQ_RCVDAV_IRQ ) { - uint8_t rcvbc = reg_read(RCVBC_ADDR); + uint8_t rcvbc = reg_read(rhport, RCVBC_ADDR, true); xact_len = (uint8_t) tu_min16(rcvbc, ep->total_len - ep->xferred_len); if ( xact_len ) { - fifo_read(ep->buf, xact_len); + fifo_read(rhport, ep->buf, xact_len, true); ep->buf += xact_len; ep->xferred_len += xact_len; } // ack RCVDVAV IRQ - reg_write(HIRQ_ADDR, HIRQ_RCVDAV_IRQ); - hirq = reg_read(HIRQ_ADDR); + reg_write(rhport, HIRQ_ADDR, HIRQ_RCVDAV_IRQ, true); + hirq = reg_read(rhport, HIRQ_ADDR, true); } if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { @@ -720,17 +726,17 @@ void hcd_int_handler(uint8_t rhport) { } if ( hirq & HIRQ_HXFRDN_IRQ ) { - reg_write(HIRQ_ADDR, HIRQ_HXFRDN_IRQ); + reg_write(rhport, HIRQ_ADDR, HIRQ_HXFRDN_IRQ, true); handle_xfer_done(rhport); } - hirq = reg_read(HIRQ_ADDR); + hirq = reg_read(rhport, HIRQ_ADDR, true); } // clear all interrupt except SNDBAV_IRQ (never clear by us). Note RCVDAV_IRQ, HXFRDN_IRQ already clear while processing hirq &= ~HIRQ_SNDBAV_IRQ; if ( hirq ) { - reg_write(HIRQ_ADDR, hirq); + reg_write(rhport, HIRQ_ADDR, hirq, true); } } -- cgit v1.3.1 From 09ceaa6cf37d29e605495716fc2497ed5228a37f Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 25 Aug 2023 13:18:47 +0700 Subject: add osal mutex for spi --- src/portable/analog/max3421/hcd_max3421.c | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 0144deca6..09845ffe4 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -194,7 +194,10 @@ typedef struct { hcd_ep_t ep[8][2]; - OSAL_MUTEX_DEF(spi_mutex); + OSAL_MUTEX_DEF(spi_mutexdef); +#if OSAL_MUTEX_REQUIRED + osal_mutex_t spi_mutex; +#endif } max2341_data_t; static max2341_data_t _hcd_data; @@ -215,6 +218,7 @@ static void max3421_spi_lock(uint8_t rhport, bool in_isr) { // disable interrupt and mutex lock (for pre-emptive RTOS) if not in_isr if (!in_isr) { tuh_max3421e_int_api(rhport, false); + (void) osal_mutex_lock(_hcd_data.spi_mutex, OSAL_TIMEOUT_WAIT_FOREVER); } // assert CS @@ -228,6 +232,7 @@ static void max3421_spi_unlock(uint8_t rhport, bool in_isr) { // mutex unlock and re-enable interrupt if (!in_isr) { tuh_max3421e_int_api(rhport, true); + (void) osal_mutex_unlock(_hcd_data.spi_mutex); } } @@ -372,12 +377,16 @@ tusb_speed_t handle_connect_irq(uint8_t rhport) { bool hcd_init(uint8_t rhport) { (void) rhport; + hcd_int_disable(rhport); + TU_LOG2_INT(sizeof(hcd_ep_t)); TU_LOG2_INT(sizeof(max2341_data_t)); tu_memclr(&_hcd_data, sizeof(_hcd_data)); - hcd_int_disable(rhport); +#if OSAL_MUTEX_REQUIRED + _hcd_data.spi_mutex = osal_mutex_create(&_hcd_data.spi_mutexdef); +#endif // full duplex, interrupt negative edge reg_write(rhport, PINCTL_ADDR, PINCTL_FDUPSPI, false); -- cgit v1.3.1 From ecf2f910424b53fecc3ca82ae410f054518cc752 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 25 Aug 2023 16:36:28 +0700 Subject: use endpoint pool for more flexible multiple devices support --- src/portable/analog/max3421/hcd_max3421.c | 178 ++++++++++++++++++++---------- 1 file changed, 121 insertions(+), 57 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 09845ffe4..b0325f240 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -165,22 +165,26 @@ enum { //--------------------------------------------------------------------+ typedef struct { - uint16_t packet_size; - struct TU_ATTR_PACKED { + uint8_t ep_dir : 1; uint8_t is_iso : 1; uint8_t data_toggle : 1; - uint8_t xfer_queued : 1; + uint8_t xfer_pending : 1; uint8_t xfer_complete : 1; }; + struct TU_ATTR_PACKED { + uint8_t daddr : 4; + uint8_t ep_num : 4; + }; + uint16_t packet_size; uint16_t total_len; uint16_t xferred_len; uint8_t* buf; -} hcd_ep_t; +} max3421_ep_t; typedef struct { - atomic_bool busy; // busy transferring + atomic_flag busy; // busy transferring // cached register uint8_t sndbc; @@ -192,15 +196,16 @@ typedef struct { volatile uint16_t frame_count; - hcd_ep_t ep[8][2]; + max3421_ep_t ep0_addr0; // control endpoint for addr0 + max3421_ep_t ep[CFG_TUH_MAX3421_ENDPOINT_TOTAL]; OSAL_MUTEX_DEF(spi_mutexdef); #if OSAL_MUTEX_REQUIRED osal_mutex_t spi_mutex; #endif -} max2341_data_t; +} max3421_data_t; -static max2341_data_t _hcd_data; +static max3421_data_t _hcd_data; //--------------------------------------------------------------------+ // API: SPI transfer with MAX3421E, must be implemented by application @@ -211,7 +216,7 @@ bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_ void tuh_max3421e_int_api(uint8_t rhport, bool enabled); //--------------------------------------------------------------------+ -// +// SPI Helper //--------------------------------------------------------------------+ static void max3421_spi_lock(uint8_t rhport, bool in_isr) { @@ -318,6 +323,44 @@ static inline void sndbc_write(uint8_t rhport, uint8_t data, bool in_isr) { reg_write(rhport, SNDBC_ADDR, data, in_isr); } +//--------------------------------------------------------------------+ +// Endpoint helper +//--------------------------------------------------------------------+ + +static max3421_ep_t* find_ep_not_addr0(uint8_t daddr, uint8_t ep_num, uint8_t ep_dir) { + for(size_t i=0; idaddr && ep_num == ep->ep_num && (ep_dir == ep->ep_dir || ep_num == 0) ) { + return ep; + } + } + + return NULL; +} + +// daddr = 0 and ep_num = 0 means find a free (allocate) endpoint +TU_ATTR_ALWAYS_INLINE static inline max3421_ep_t * allocate_ep(void) { + return find_ep_not_addr0(0, 0, 0); +} + +// free all endpoints belong to device address +static void free_ep(uint8_t daddr) { + for (size_t i=0; idaddr == daddr) { + tu_memclr(ep, sizeof(max3421_ep_t)); + } + } +} + +TU_ATTR_ALWAYS_INLINE static inline max3421_ep_t * find_opened_ep(uint8_t daddr, uint8_t ep_num, uint8_t ep_dir) { + if (daddr == 0 && ep_num == 0) { + return &_hcd_data.ep0_addr0; + }else{ + return find_ep_not_addr0(daddr, ep_num, ep_dir); + } +} //--------------------------------------------------------------------+ // Controller API @@ -379,8 +422,8 @@ bool hcd_init(uint8_t rhport) { hcd_int_disable(rhport); - TU_LOG2_INT(sizeof(hcd_ep_t)); - TU_LOG2_INT(sizeof(max2341_data_t)); + TU_LOG2_INT(sizeof(max3421_ep_t)); + TU_LOG2_INT(sizeof(max3421_data_t)); tu_memclr(&_hcd_data, sizeof(_hcd_data)); @@ -478,22 +521,29 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { //--------------------------------------------------------------------+ // Open an endpoint -bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc) { +bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * ep_desc) { (void) rhport; - (void) dev_addr; + (void) daddr; uint8_t ep_num = tu_edpt_number(ep_desc->bEndpointAddress); uint8_t ep_dir = tu_edpt_dir(ep_desc->bEndpointAddress); - hcd_ep_t * ep = &_hcd_data.ep[ep_num][ep_dir]; - - ep->packet_size = tu_edpt_packet_size(ep_desc); + max3421_ep_t * ep; + if (daddr == 0 && ep_num == 0) { + ep = &_hcd_data.ep0_addr0; + }else { + ep = allocate_ep(); + TU_ASSERT(ep); + ep->daddr = daddr; + ep->ep_num = ep_num; + ep->ep_dir = ep_dir; + } - if (ep_desc->bEndpointAddress == 0) { - _hcd_data.ep[0][1].packet_size = ep->packet_size; + if ( TUSB_XFER_ISOCHRONOUS == ep_desc->bmAttributes.xfer ) { + ep->is_iso = 1; } - ep->is_iso = (TUSB_XFER_ISOCHRONOUS == ep_desc->bmAttributes.xfer) ? 1 : 0; + ep->packet_size = tu_edpt_packet_size(ep_desc); return true; } @@ -505,49 +555,54 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf uint8_t const ep_num = tu_edpt_number(ep_addr); uint8_t const ep_dir = tu_edpt_dir(ep_addr); - hcd_ep_t* ep = &_hcd_data.ep[ep_num][ep_dir]; + max3421_ep_t* ep = find_opened_ep(daddr, ep_num, ep_dir); + TU_ASSERT(ep); ep->buf = buffer; ep->total_len = buflen; ep->xferred_len = 0; ep->xfer_complete = 0; - ep->xfer_queued = 1; - - peraddr_write(rhport, daddr, false); - - uint8_t hctl = 0; - uint8_t hxfr = ep_num; - - if ( ep->is_iso ) { - hxfr |= HXFR_ISO; - } else if ( ep_num == 0 ) { - ep->data_toggle = 1; - if ( buffer == NULL || buflen == 0 ) { - // ZLP for ACK stage, use HS - hxfr |= HXFR_HS; - hxfr |= (ep_dir ? 0 : HXFR_OUT_NIN); - hxfr_write(rhport, hxfr, false); - return true; + ep->xfer_pending = 1; + + // carry out transfer if not busy +// if ( atomic_flag_test_and_set(&_hcd_data.busy) ) + { + peraddr_write(rhport, daddr, false); + + uint8_t hctl = 0; + uint8_t hxfr = ep_num; + + if ( ep->is_iso ) { + hxfr |= HXFR_ISO; + } else if ( ep_num == 0 ) { + ep->data_toggle = 1; + if ( buffer == NULL || buflen == 0 ) { + // ZLP for ACK stage, use HS + hxfr |= HXFR_HS; + hxfr |= (ep_dir ? 0 : HXFR_OUT_NIN); + hxfr_write(rhport, hxfr, false); + return true; + } } - } - if ( 0 == ep_dir ) { - // Page 12: Programming BULK-OUT Transfers - TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ); + if ( 0 == ep_dir ) { + // Page 12: Programming BULK-OUT Transfers + TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ); - uint8_t const xact_len = (uint8_t) tu_min16(buflen, ep->packet_size); - fifo_write(rhport, SNDFIFO_ADDR, buffer, xact_len, false); - sndbc_write(rhport, xact_len, false); + uint8_t const xact_len = (uint8_t) tu_min16(buflen, ep->packet_size); + fifo_write(rhport, SNDFIFO_ADDR, buffer, xact_len, false); + sndbc_write(rhport, xact_len, false); - hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); - hxfr |= HXFR_OUT_NIN; - } else { - // Page 13: Programming BULK-IN Transfers - hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); - } + hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); + hxfr |= HXFR_OUT_NIN; + } else { + // Page 13: Programming BULK-IN Transfers + hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); + } - reg_write(rhport, HCTL_ADDR, hctl, false); - hxfr_write(rhport, hxfr, false); + reg_write(rhport, HCTL_ADDR, hctl, false); + hxfr_write(rhport, hxfr, false); + } return true; } @@ -566,7 +621,7 @@ bool hcd_edpt_abort_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8]) { (void) rhport; - hcd_ep_t* ep = &_hcd_data.ep[0][0]; + max3421_ep_t* ep = find_opened_ep(daddr, 0, 0); ep->total_len = 8; ep->xferred_len = 0; @@ -624,7 +679,7 @@ static void handle_xfer_done(uint8_t rhport) { if ( (hxfr_type & HXFR_SETUP) || (hxfr_type & HXFR_OUT_NIN) ) { // SETUP or OUT transfer - hcd_ep_t *ep = &_hcd_data.ep[ep_num][0]; + max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, 0); uint8_t xact_len; if ( hxfr_type & HXFR_SETUP) { @@ -644,10 +699,15 @@ static void handle_xfer_done(uint8_t rhport) { hcd_event_xfer_complete(_hcd_data.peraddr, ep_num, ep->xferred_len, xfer_result, true); }else { // more to transfer + xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); + fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, true); + sndbc_write(rhport, xact_len, true); + + hxfr_write(rhport, _hcd_data.hxfr, true); } } else { // IN transfer: fifo data is already received in RCVDAV IRQ - hcd_ep_t *ep = &_hcd_data.ep[ep_num][1]; + max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, 1); if ( hxfr_type & HXFR_HS ) { ep->xfer_complete = 1; @@ -702,6 +762,10 @@ void hcd_int_handler(uint8_t rhport) { if (speed == TUSB_SPEED_INVALID) { hcd_event_device_remove(rhport, true); }else { + // FIXME multiple MAX3421 rootdevice address is not 1 + uint8_t const daddr = 1; + free_ep(daddr); + hcd_event_device_attach(rhport, true); } } @@ -710,8 +774,8 @@ void hcd_int_handler(uint8_t rhport) { // not call this handler again. So we need to loop until all IRQ are cleared while ( hirq & (HIRQ_RCVDAV_IRQ | HIRQ_HXFRDN_IRQ) ) { if ( hirq & HIRQ_RCVDAV_IRQ ) { - uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; - hcd_ep_t *ep = &_hcd_data.ep[ep_num][1]; + uint8_t const ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; + max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, 1); uint8_t xact_len; // RCVDAV_IRQ can trigger 2 times (dual buffered) -- cgit v1.3.1 From ac00b9147298184ca0bd1eadac3a02e7e867085d Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 25 Aug 2023 17:26:57 +0700 Subject: add xact_out(), xact_in() to manage transfer --- src/portable/analog/max3421/hcd_max3421.c | 143 +++++++++++++++++++----------- 1 file changed, 89 insertions(+), 54 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index b0325f240..00b36201c 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -331,7 +331,7 @@ static max3421_ep_t* find_ep_not_addr0(uint8_t daddr, uint8_t ep_num, uint8_t ep for(size_t i=0; idaddr && ep_num == ep->ep_num && (ep_dir == ep->ep_dir || ep_num == 0) ) { + if (daddr == ep->daddr && ep_num == ep->ep_num && (ep_dir == ep->ep_dir || ep_num == 0)) { return ep; } } @@ -362,6 +362,28 @@ TU_ATTR_ALWAYS_INLINE static inline max3421_ep_t * find_opened_ep(uint8_t daddr, } } +//static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { +// size_t idx = cur_ep - _hcd_data.ep; +// +// // starting from next endpoint +// for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { +// max3421_ep_t* ep = &_hcd_data.ep[i]; +// if (ep->xfer_pending) { +// return ep; +// } +// } +// +// // wrap around including current endpoint +// for (size_t i = 0; i <= idx; i++) { +// max3421_ep_t* ep = &_hcd_data.ep[i]; +// if (ep->xfer_pending) { +// return ep; +// } +// } +// +// return NULL; +//} + //--------------------------------------------------------------------+ // Controller API //--------------------------------------------------------------------+ @@ -548,6 +570,37 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * e return true; } +void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { + // Page 12: Programming BULK-OUT Transfers + // TODO double buffered + if (switch_ep) { + peraddr_write(rhport, ep->daddr, in_isr); + + uint8_t const hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); + reg_write(rhport, HCTL_ADDR, hctl, in_isr); + } + + uint8_t const xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); + fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, in_isr); + sndbc_write(rhport, xact_len, in_isr); + + uint8_t const hxfr = ep->ep_num | HXFR_OUT_NIN | (ep->is_iso ? HXFR_ISO : 0); + hxfr_write(rhport, hxfr, in_isr); +} + +void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { + // Page 13: Programming BULK-IN Transfers + if (switch_ep) { + peraddr_write(rhport, ep->daddr, in_isr); + + uint8_t const hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); + reg_write(rhport, HCTL_ADDR, hctl, in_isr); + } + + uint8_t const hxfr = ep->ep_num | (ep->is_iso ? HXFR_ISO : 0); + hxfr_write(rhport, hxfr, in_isr); +} + // Submit a transfer, when complete hcd_event_xfer_complete() must be invoked bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { (void) rhport; @@ -567,17 +620,14 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf // carry out transfer if not busy // if ( atomic_flag_test_and_set(&_hcd_data.busy) ) { - peraddr_write(rhport, daddr, false); - - uint8_t hctl = 0; uint8_t hxfr = ep_num; - if ( ep->is_iso ) { - hxfr |= HXFR_ISO; - } else if ( ep_num == 0 ) { + if ( ep_num == 0 ) { ep->data_toggle = 1; if ( buffer == NULL || buflen == 0 ) { // ZLP for ACK stage, use HS + peraddr_write(rhport, daddr, false); + hxfr |= HXFR_HS; hxfr |= (ep_dir ? 0 : HXFR_OUT_NIN); hxfr_write(rhport, hxfr, false); @@ -586,22 +636,11 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf } if ( 0 == ep_dir ) { - // Page 12: Programming BULK-OUT Transfers TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ); - - uint8_t const xact_len = (uint8_t) tu_min16(buflen, ep->packet_size); - fifo_write(rhport, SNDFIFO_ADDR, buffer, xact_len, false); - sndbc_write(rhport, xact_len, false); - - hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); - hxfr |= HXFR_OUT_NIN; + xact_out(rhport, ep, true, false); } else { - // Page 13: Programming BULK-IN Transfers - hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); + xact_in(rhport, ep, true, false); } - - reg_write(rhport, HCTL_ADDR, hctl, false); - hxfr_write(rhport, hxfr, false); } return true; @@ -644,7 +683,12 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { static void handle_xfer_done(uint8_t rhport) { uint8_t const hrsl = reg_read(rhport, HRSL_ADDR, true); uint8_t const hresult = hrsl & HRSL_RESULT_MASK; - uint8_t ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; + + uint8_t const ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; + uint8_t const hxfr_type = _hcd_data.hxfr & 0xf0; + uint8_t const ep_dir = ((hxfr_type & HXFR_SETUP) || (hxfr_type & HXFR_OUT_NIN)) ? 0 : 1; + + max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, ep_dir); xfer_result_t xfer_result; @@ -663,10 +707,11 @@ static void handle_xfer_done(uint8_t rhport) { return; case HRSL_NAK: - // NAK on control, retry immediately - //if (ep_num == 0) - { + if (ep_num == 0) { + // NAK on control, retry immediately hxfr_write(rhport, _hcd_data.hxfr, true); + }else { + // NAK on non-control, find next pending to switch } return; @@ -675,16 +720,28 @@ static void handle_xfer_done(uint8_t rhport) { break; } - uint8_t const hxfr_type = _hcd_data.hxfr & 0xf0; + if (ep_dir) { + // IN transfer: fifo data is already received in RCVDAV IRQ + if ( hxfr_type & HXFR_HS ) { + ep->xfer_complete = 1; + } - if ( (hxfr_type & HXFR_SETUP) || (hxfr_type & HXFR_OUT_NIN) ) { + // short packet or all bytes transferred + if ( ep->xfer_complete ) { + // save data toggle + ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; + hcd_event_xfer_complete(_hcd_data.peraddr, TUSB_DIR_IN_MASK | ep_num, ep->xferred_len, xfer_result, true); + }else { + // more to transfer + hxfr_write(rhport, _hcd_data.hxfr, true); + } + } else { // SETUP or OUT transfer - max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, 0); uint8_t xact_len; - if ( hxfr_type & HXFR_SETUP) { + if (hxfr_type & HXFR_SETUP) { xact_len = 8; - } else if ( hxfr_type & HXFR_HS ) { + } else if (hxfr_type & HXFR_HS) { xact_len = 0; } else { xact_len = _hcd_data.sndbc; @@ -693,34 +750,12 @@ static void handle_xfer_done(uint8_t rhport) { ep->xferred_len += xact_len; ep->buf += xact_len; - if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { + if (xact_len < ep->packet_size || ep->xferred_len >= ep->total_len) { // save data toggle ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; hcd_event_xfer_complete(_hcd_data.peraddr, ep_num, ep->xferred_len, xfer_result, true); - }else { - // more to transfer - xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); - fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, true); - sndbc_write(rhport, xact_len, true); - - hxfr_write(rhport, _hcd_data.hxfr, true); - } - } else { - // IN transfer: fifo data is already received in RCVDAV IRQ - max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, 1); - - if ( hxfr_type & HXFR_HS ) { - ep->xfer_complete = 1; - } - - // short packet or all bytes transferred - if ( ep->xfer_complete ) { - // save data toggle - ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; - hcd_event_xfer_complete(_hcd_data.peraddr, TUSB_DIR_IN_MASK | ep_num, ep->xferred_len, xfer_result, true); - }else { - // more to transfer - hxfr_write(rhport, _hcd_data.hxfr, true); + } else { + xact_out(rhport, ep, false, true); } } } -- cgit v1.3.1 From cd7464a8847db5efa14f568bdf8746d898fc7eb4 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 25 Aug 2023 17:37:09 +0700 Subject: try next endpoint when received NAK --- src/portable/analog/max3421/hcd_max3421.c | 58 ++++++++++++++++++++----------- 1 file changed, 37 insertions(+), 21 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 00b36201c..e546f99ce 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -362,27 +362,27 @@ TU_ATTR_ALWAYS_INLINE static inline max3421_ep_t * find_opened_ep(uint8_t daddr, } } -//static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { -// size_t idx = cur_ep - _hcd_data.ep; -// -// // starting from next endpoint -// for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { -// max3421_ep_t* ep = &_hcd_data.ep[i]; -// if (ep->xfer_pending) { -// return ep; -// } -// } -// -// // wrap around including current endpoint -// for (size_t i = 0; i <= idx; i++) { -// max3421_ep_t* ep = &_hcd_data.ep[i]; -// if (ep->xfer_pending) { -// return ep; -// } -// } -// -// return NULL; -//} +static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { + size_t idx = cur_ep - _hcd_data.ep; + + // starting from next endpoint + for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { + max3421_ep_t* ep = &_hcd_data.ep[i]; + if (ep->xfer_pending) { + return ep; + } + } + + // wrap around including current endpoint + for (size_t i = 0; i <= idx; i++) { + max3421_ep_t* ep = &_hcd_data.ep[i]; + if (ep->xfer_pending) { + return ep; + } + } + + return NULL; +} //--------------------------------------------------------------------+ // Controller API @@ -443,6 +443,7 @@ bool hcd_init(uint8_t rhport) { (void) rhport; hcd_int_disable(rhport); + tuh_max3421_spi_cs_api(rhport, false); TU_LOG2_INT(sizeof(max3421_ep_t)); TU_LOG2_INT(sizeof(max3421_data_t)); @@ -689,6 +690,7 @@ static void handle_xfer_done(uint8_t rhport) { uint8_t const ep_dir = ((hxfr_type & HXFR_SETUP) || (hxfr_type & HXFR_OUT_NIN)) ? 0 : 1; max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, ep_dir); + TU_ASSERT(ep, ); xfer_result_t xfer_result; @@ -712,6 +714,20 @@ static void handle_xfer_done(uint8_t rhport) { hxfr_write(rhport, _hcd_data.hxfr, true); }else { // NAK on non-control, find next pending to switch + max3421_ep_t *next_ep = find_next_pending_ep(ep); + TU_ASSERT(next_ep, ); + + if (ep == next_ep) { + // only one pending, retry immediately + hxfr_write(rhport, _hcd_data.hxfr, true); + }else { + // switch to next pending TODO could have issue with double buffered if not clear previously out data + if ( ep_dir ) { + xact_in(rhport, next_ep, true, true); + } else { + xact_out(rhport, next_ep, true, true); + } + } } return; -- cgit v1.3.1 From 502b1bdda62f0f207d9a51daf134574e455f3aa2 Mon Sep 17 00:00:00 2001 From: hathach Date: Sun, 27 Aug 2023 23:45:34 +0700 Subject: more update to transaction --- examples/host/cdc_msc_hid/src/tusb_config.h | 9 ++-- examples/host/msc_file_explorer/src/tusb_config.h | 10 +++-- src/common/tusb_mcu.h | 12 ++++++ src/host/hcd.h | 4 +- src/host/usbh.c | 1 + src/portable/analog/max3421/hcd_max3421.c | 51 +++++++++++++++-------- 6 files changed, 62 insertions(+), 25 deletions(-) (limited to 'src/portable') diff --git a/examples/host/cdc_msc_hid/src/tusb_config.h b/examples/host/cdc_msc_hid/src/tusb_config.h index abb75f068..7d621d466 100644 --- a/examples/host/cdc_msc_hid/src/tusb_config.h +++ b/examples/host/cdc_msc_hid/src/tusb_config.h @@ -35,9 +35,12 @@ //--------------------------------------------------------------------+ #if CFG_TUSB_MCU == OPT_MCU_RP2040 -// change to 1 if using pico-pio-usb as host controller for raspberry rp2040 -#define CFG_TUH_RPI_PIO_USB 0 -#define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB + // change to 1 if using pico-pio-usb as host controller for raspberry rp2040 + #define CFG_TUH_RPI_PIO_USB 0 + #define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB +#elif CFG_TUSB_MCU == OPT_MCU_NRF5X + // Use external USB controller (via SPI) MAX3421E (aka usb host shield) + #define CFG_TUH_MAX3421 1 #endif // RHPort number used for host can be defined by board.mk, default to port 0 diff --git a/examples/host/msc_file_explorer/src/tusb_config.h b/examples/host/msc_file_explorer/src/tusb_config.h index 1e0d067bf..bb2fd4cf5 100644 --- a/examples/host/msc_file_explorer/src/tusb_config.h +++ b/examples/host/msc_file_explorer/src/tusb_config.h @@ -35,11 +35,15 @@ //--------------------------------------------------------------------+ #if CFG_TUSB_MCU == OPT_MCU_RP2040 -// change to 1 if using pico-pio-usb as host controller for raspberry rp2040 -#define CFG_TUH_RPI_PIO_USB 0 -#define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB + // change to 1 if using pico-pio-usb as host controller for raspberry rp2040 + #define CFG_TUH_RPI_PIO_USB 0 + #define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_US +#elif CFG_TUSB_MCU == OPT_MCU_NRF5X + // Use external USB controller (via SPI) MAX3421E (aka usb host shield) + #define CFG_TUH_MAX3421 1 #endif + // RHPort number used for host can be defined by board.mk, default to port 0 #ifndef BOARD_TUH_RHPORT #define BOARD_TUH_RHPORT 0 diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 35f94efbc..21939df7c 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -385,6 +385,18 @@ #define TUP_RHPORT_HIGHSPEED 1 #endif + +//--------------------------------------------------------------------+ +// External USB controller +//--------------------------------------------------------------------+ + +#if defined(CFG_TUH_MAX3421) & CFG_TUH_MAX3421 + #ifndef CFG_TUH_MAX3421_ENDPOINT_TOTAL + #define CFG_TUH_MAX3421_ENDPOINT_TOTAL (8 + 4*(CFG_TUH_DEVICE_MAX-1)) + #endif +#endif + + //--------------------------------------------------------------------+ // Default Values //--------------------------------------------------------------------+ diff --git a/src/host/hcd.h b/src/host/hcd.h index 1f01a1a2f..e25b20ea3 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -39,7 +39,7 @@ // Configuration //--------------------------------------------------------------------+ -// Max number of endpoints per device +// Max number of endpoints pair per device // TODO optimize memory usage #ifndef CFG_TUH_ENDPOINT_MAX #define CFG_TUH_ENDPOINT_MAX 16 @@ -167,7 +167,7 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr); //--------------------------------------------------------------------+ // Open an endpoint -bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const * ep_desc); +bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * ep_desc); // Submit a transfer, when complete hcd_event_xfer_complete() must be invoked bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen); diff --git a/src/host/usbh.c b/src/host/usbh.c index 7a09f5b6e..12a7f5839 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -919,6 +919,7 @@ TU_ATTR_FAST_FUNC void hcd_event_handler(hcd_event_t const* event, bool in_isr) switch (event->event_id) { // case HCD_EVENT_DEVICE_REMOVE: +// // FIXME device remove from a hub need an HCD API for hcd to free up endpoint // // mark device as removing to prevent further xfer before the event is processed in usbh task // break; diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index e546f99ce..574cca788 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -582,6 +582,7 @@ void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { } uint8_t const xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); + TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ, ); fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, in_isr); sndbc_write(rhport, xact_len, in_isr); @@ -602,6 +603,28 @@ void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { hxfr_write(rhport, hxfr, in_isr); } +TU_ATTR_ALWAYS_INLINE static inline void xact_inout(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { + if (ep->ep_dir) { + xact_in(rhport, ep, switch_ep, in_isr); + }else { + xact_out(rhport, ep, switch_ep, in_isr); + } +} + +void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t result, uint8_t data_toggle) { + (void) rhport; + (void) result; + ep->xfer_pending = 0; + ep->data_toggle = data_toggle; + //uint8_t const ep_addr = tu_edpt_addr(ep->ep_num, ep->ep_dir); + //hcd_event_xfer_complete(rhport, ep_addr, ep->xferred_len, result, true); + +// max3421_ep_t *next_ep = find_next_pending_ep(ep); +// if (next_ep) { +// xact_inout(rhport, next_ep, true, true); +// } +} + // Submit a transfer, when complete hcd_event_xfer_complete() must be invoked bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { (void) rhport; @@ -612,6 +635,9 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf max3421_ep_t* ep = find_opened_ep(daddr, ep_num, ep_dir); TU_ASSERT(ep); + // control transfer can switch direction + ep->ep_dir = ep_dir; + ep->buf = buffer; ep->total_len = buflen; ep->xferred_len = 0; @@ -636,12 +662,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf } } - if ( 0 == ep_dir ) { - TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ); - xact_out(rhport, ep, true, false); - } else { - xact_in(rhport, ep, true, false); - } + xact_inout(rhport, ep, true, false); } return true; @@ -662,6 +683,7 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] (void) rhport; max3421_ep_t* ep = find_opened_ep(daddr, 0, 0); + ep->ep_dir = 0; ep->total_len = 8; ep->xferred_len = 0; @@ -715,18 +737,13 @@ static void handle_xfer_done(uint8_t rhport) { }else { // NAK on non-control, find next pending to switch max3421_ep_t *next_ep = find_next_pending_ep(ep); - TU_ASSERT(next_ep, ); if (ep == next_ep) { // only one pending, retry immediately hxfr_write(rhport, _hcd_data.hxfr, true); - }else { + }else if (next_ep) { // switch to next pending TODO could have issue with double buffered if not clear previously out data - if ( ep_dir ) { - xact_in(rhport, next_ep, true, true); - } else { - xact_out(rhport, next_ep, true, true); - } + xact_inout(rhport, next_ep, true, true); } } return; @@ -744,8 +761,8 @@ static void handle_xfer_done(uint8_t rhport) { // short packet or all bytes transferred if ( ep->xfer_complete ) { - // save data toggle - ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; + uint8_t const dt = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; // save data toggle + xfer_complete_isr(rhport, ep, xfer_result, dt); hcd_event_xfer_complete(_hcd_data.peraddr, TUSB_DIR_IN_MASK | ep_num, ep->xferred_len, xfer_result, true); }else { // more to transfer @@ -767,8 +784,8 @@ static void handle_xfer_done(uint8_t rhport) { ep->buf += xact_len; if (xact_len < ep->packet_size || ep->xferred_len >= ep->total_len) { - // save data toggle - ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; + uint8_t const dt = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; // save data toggle + xfer_complete_isr(rhport, ep, xfer_result, dt); hcd_event_xfer_complete(_hcd_data.peraddr, ep_num, ep->xferred_len, xfer_result, true); } else { xact_out(rhport, ep, false, true); -- cgit v1.3.1 From b31924e13edff0f29829056152348a9255e72169 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 28 Aug 2023 12:41:44 +0700 Subject: - add xfer_complete_isr() - merge addr0 ep to pool - add control status to xact in/out - use atomic flag busy to ensure only 1 transfer is active at any time - execute pending transfer after one is complete (or clear busy flag) - change rtt mode to block if full --- hw/bsp/family_support.cmake | 1 + src/portable/analog/max3421/hcd_max3421.c | 118 +++++++++++++++--------------- 2 files changed, 62 insertions(+), 57 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index 7c89427c0..1cbcfb2a7 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -216,6 +216,7 @@ function(family_configure_common TARGET RTOS) if (NOT TARGET segger_rtt) add_library(segger_rtt STATIC ${TOP}/lib/SEGGER_RTT/RTT/SEGGER_RTT.c) target_include_directories(segger_rtt PUBLIC ${TOP}/lib/SEGGER_RTT/RTT) + target_compile_definitions(segger_rtt PUBLIC SEGGER_RTT_MODE_DEFAULT=SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL) endif() target_link_libraries(${TARGET} PUBLIC segger_rtt) endif () diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 574cca788..262dbca0f 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -195,9 +195,7 @@ typedef struct { uint8_t hxfr; volatile uint16_t frame_count; - - max3421_ep_t ep0_addr0; // control endpoint for addr0 - max3421_ep_t ep[CFG_TUH_MAX3421_ENDPOINT_TOTAL]; + max3421_ep_t ep[CFG_TUH_MAX3421_ENDPOINT_TOTAL]; // [0] is reserved for addr0 OSAL_MUTEX_DEF(spi_mutexdef); #if OSAL_MUTEX_REQUIRED @@ -328,7 +326,7 @@ static inline void sndbc_write(uint8_t rhport, uint8_t data, bool in_isr) { //--------------------------------------------------------------------+ static max3421_ep_t* find_ep_not_addr0(uint8_t daddr, uint8_t ep_num, uint8_t ep_dir) { - for(size_t i=0; idaddr && ep_num == ep->ep_num && (ep_dir == ep->ep_dir || ep_num == 0)) { @@ -344,9 +342,17 @@ TU_ATTR_ALWAYS_INLINE static inline max3421_ep_t * allocate_ep(void) { return find_ep_not_addr0(0, 0, 0); } +TU_ATTR_ALWAYS_INLINE static inline max3421_ep_t * find_opened_ep(uint8_t daddr, uint8_t ep_num, uint8_t ep_dir) { + if (daddr == 0 && ep_num == 0) { + return &_hcd_data.ep[0]; + }else{ + return find_ep_not_addr0(daddr, ep_num, ep_dir); + } +} + // free all endpoints belong to device address static void free_ep(uint8_t daddr) { - for (size_t i=0; idaddr == daddr) { tu_memclr(ep, sizeof(max3421_ep_t)); @@ -354,16 +360,8 @@ static void free_ep(uint8_t daddr) { } } -TU_ATTR_ALWAYS_INLINE static inline max3421_ep_t * find_opened_ep(uint8_t daddr, uint8_t ep_num, uint8_t ep_dir) { - if (daddr == 0 && ep_num == 0) { - return &_hcd_data.ep0_addr0; - }else{ - return find_ep_not_addr0(daddr, ep_num, ep_dir); - } -} - static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { - size_t idx = cur_ep - _hcd_data.ep; + size_t const idx = cur_ep - _hcd_data.ep; // starting from next endpoint for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { @@ -553,7 +551,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * e max3421_ep_t * ep; if (daddr == 0 && ep_num == 0) { - ep = &_hcd_data.ep0_addr0; + ep = &_hcd_data.ep[0]; }else { ep = allocate_ep(); TU_ASSERT(ep); @@ -581,12 +579,20 @@ void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { reg_write(rhport, HCTL_ADDR, hctl, in_isr); } - uint8_t const xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); - TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ, ); - fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, in_isr); - sndbc_write(rhport, xact_len, in_isr); + uint8_t hxfr = ep->ep_num | HXFR_OUT_NIN | (ep->is_iso ? HXFR_ISO : 0); + + if (ep->ep_num == 0 && (ep->buf == NULL || ep->total_len == 0)) { + // Control ZLP status use HS + hxfr |= HXFR_HS; + } else { + uint8_t const xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); + TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ,); + if (xact_len) { + fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, in_isr); + } + sndbc_write(rhport, xact_len, in_isr); + } - uint8_t const hxfr = ep->ep_num | HXFR_OUT_NIN | (ep->is_iso ? HXFR_ISO : 0); hxfr_write(rhport, hxfr, in_isr); } @@ -599,7 +605,12 @@ void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { reg_write(rhport, HCTL_ADDR, hctl, in_isr); } - uint8_t const hxfr = ep->ep_num | (ep->is_iso ? HXFR_ISO : 0); + uint8_t hxfr = ep->ep_num | (ep->is_iso ? HXFR_ISO : 0); + if (ep->ep_num == 0 && (ep->buf == NULL || ep->total_len == 0)) { + // Control ZLP status use HS + hxfr |= HXFR_HS; + } + hxfr_write(rhport, hxfr, in_isr); } @@ -611,24 +622,8 @@ TU_ATTR_ALWAYS_INLINE static inline void xact_inout(uint8_t rhport, max3421_ep_t } } -void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t result, uint8_t data_toggle) { - (void) rhport; - (void) result; - ep->xfer_pending = 0; - ep->data_toggle = data_toggle; - //uint8_t const ep_addr = tu_edpt_addr(ep->ep_num, ep->ep_dir); - //hcd_event_xfer_complete(rhport, ep_addr, ep->xferred_len, result, true); - -// max3421_ep_t *next_ep = find_next_pending_ep(ep); -// if (next_ep) { -// xact_inout(rhport, next_ep, true, true); -// } -} - // Submit a transfer, when complete hcd_event_xfer_complete() must be invoked bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { - (void) rhport; - uint8_t const ep_num = tu_edpt_number(ep_addr); uint8_t const ep_dir = tu_edpt_dir(ep_addr); @@ -644,24 +639,12 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->xfer_complete = 0; ep->xfer_pending = 1; - // carry out transfer if not busy -// if ( atomic_flag_test_and_set(&_hcd_data.busy) ) - { - uint8_t hxfr = ep_num; - - if ( ep_num == 0 ) { - ep->data_toggle = 1; - if ( buffer == NULL || buflen == 0 ) { - // ZLP for ACK stage, use HS - peraddr_write(rhport, daddr, false); - - hxfr |= HXFR_HS; - hxfr |= (ep_dir ? 0 : HXFR_OUT_NIN); - hxfr_write(rhport, hxfr, false); - return true; - } - } + if ( ep_num == 0 ) { + ep->data_toggle = 1; + } + // carry out transfer if not busy + if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { xact_inout(rhport, ep, true, false); } @@ -683,6 +666,8 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] (void) rhport; max3421_ep_t* ep = find_opened_ep(daddr, 0, 0); + TU_ASSERT(ep); + ep->ep_dir = 0; ep->total_len = 8; ep->xferred_len = 0; @@ -703,6 +688,26 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { return false; } +//--------------------------------------------------------------------+ +// Interrupt Handler +//--------------------------------------------------------------------+ + +static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t result, uint8_t data_toggle) { + uint8_t const ep_addr = tu_edpt_addr(ep->ep_num, ep->ep_dir); + ep->data_toggle = data_toggle; + ep->xfer_pending = 0; + hcd_event_xfer_complete(ep->daddr, ep_addr, ep->xferred_len, result, true); + + // Find next pending endpoint + max3421_ep_t *next_ep = find_next_pending_ep(ep); + if (next_ep) { + xact_inout(rhport, next_ep, true, true); + }else { + // no more pending + atomic_flag_clear(&_hcd_data.busy); + } +} + static void handle_xfer_done(uint8_t rhport) { uint8_t const hrsl = reg_read(rhport, HRSL_ADDR, true); uint8_t const hresult = hrsl & HRSL_RESULT_MASK; @@ -739,7 +744,7 @@ static void handle_xfer_done(uint8_t rhport) { max3421_ep_t *next_ep = find_next_pending_ep(ep); if (ep == next_ep) { - // only one pending, retry immediately + // this endpoint is only one pending, retry immediately hxfr_write(rhport, _hcd_data.hxfr, true); }else if (next_ep) { // switch to next pending TODO could have issue with double buffered if not clear previously out data @@ -763,7 +768,6 @@ static void handle_xfer_done(uint8_t rhport) { if ( ep->xfer_complete ) { uint8_t const dt = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; // save data toggle xfer_complete_isr(rhport, ep, xfer_result, dt); - hcd_event_xfer_complete(_hcd_data.peraddr, TUSB_DIR_IN_MASK | ep_num, ep->xferred_len, xfer_result, true); }else { // more to transfer hxfr_write(rhport, _hcd_data.hxfr, true); @@ -786,8 +790,8 @@ static void handle_xfer_done(uint8_t rhport) { if (xact_len < ep->packet_size || ep->xferred_len >= ep->total_len) { uint8_t const dt = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; // save data toggle xfer_complete_isr(rhport, ep, xfer_result, dt); - hcd_event_xfer_complete(_hcd_data.peraddr, ep_num, ep->xferred_len, xfer_result, true); } else { + // more to transfer xact_out(rhport, ep, false, true); } } -- cgit v1.3.1 From 588b758717f3c22aa8046d61247b9967de8840b7 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 28 Aug 2023 17:34:22 +0700 Subject: rename OPT_MCU_KINETIS_K64 to OPT_MCU_KINETIS_K --- hw/bsp/board_mcu.h | 2 +- src/common/tusb_mcu.h | 2 +- src/portable/nxp/khci/dcd_khci.c | 6 +++--- src/tusb_option.h | 2 +- 4 files changed, 6 insertions(+), 6 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/board_mcu.h b/hw/bsp/board_mcu.h index 3928435f0..b0f7891b4 100644 --- a/hw/bsp/board_mcu.h +++ b/hw/bsp/board_mcu.h @@ -47,7 +47,7 @@ #elif TU_CHECK_MCU(OPT_MCU_LPC51UXX, OPT_MCU_LPC54XXX, OPT_MCU_LPC55XX, OPT_MCU_MCXN9) #include "fsl_device_registers.h" -#elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32L, OPT_MCU_KINETIS_K64) +#elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32L, OPT_MCU_KINETIS_K) #include "fsl_device_registers.h" #elif CFG_TUSB_MCU == OPT_MCU_NRF5X diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 4a0c5acef..d983f8677 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -97,7 +97,7 @@ #define TUP_DCD_ENDPOINT_MAX 8 #define TUP_RHPORT_HIGHSPEED 1 -#elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32L, OPT_MCU_KINETIS_K64) +#elif TU_CHECK_MCU(OPT_MCU_KINETIS_KL, OPT_MCU_KINETIS_K32L, OPT_MCU_KINETIS_K) #define TUP_USBIP_CHIPIDEA_FS #define TUP_USBIP_CHIPIDEA_FS_KINETIS #define TUP_DCD_ENDPOINT_MAX 16 diff --git a/src/portable/nxp/khci/dcd_khci.c b/src/portable/nxp/khci/dcd_khci.c index d957338ad..2293d1b59 100644 --- a/src/portable/nxp/khci/dcd_khci.c +++ b/src/portable/nxp/khci/dcd_khci.c @@ -269,10 +269,10 @@ void dcd_init(uint8_t rhport) { (void) rhport; -#if (CFG_TUSB_MCU == OPT_MCU_KINETIS_K64) +#if (CFG_TUSB_MCU == OPT_MCU_KINETIS_K) uint32_t clk_recover_irc_en; uint32_t clk_recover_ctrl; - + clk_recover_irc_en = KHCI->CLK_RECOVER_IRC_EN; clk_recover_ctrl = KHCI->CLK_RECOVER_CTRL; @@ -284,7 +284,7 @@ void dcd_init(uint8_t rhport) #else KHCI->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; while (KHCI->USBTRC0 & USB_USBTRC0_USBRESET_MASK); -#endif +#endif tu_memclr(&_dcd, sizeof(_dcd)); KHCI->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ diff --git a/src/tusb_option.h b/src/tusb_option.h index bbaa2a53a..bf2667c4c 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -121,7 +121,7 @@ #define OPT_MCU_KINETIS_KL 1200 ///< NXP KL series #define OPT_MCU_KINETIS_K32L 1201 ///< NXP K32L series #define OPT_MCU_KINETIS_K32 1201 ///< Alias to K32L -#define OPT_MCU_KINETIS_K64 1202 ///< NXP K64 series +#define OPT_MCU_KINETIS_K 1202 ///< NXP K series #define OPT_MCU_MKL25ZXX 1200 ///< Alias to KL (obsolete) #define OPT_MCU_K32L2BXX 1201 ///< Alias to K32 (obsolete) -- cgit v1.3.1 From 3740a3287ad5965df34639e90bfa890b36c0fd60 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 29 Aug 2023 18:22:21 +0700 Subject: - correct tuh_max3421e_int_api() for nrf52 - hcd_int_disable/enable is software only to reduce interrupt lag --- hw/bsp/nrf/boards/pca10056/board.h | 9 ++++ hw/bsp/nrf/family.c | 20 ++++++- src/portable/analog/max3421/hcd_max3421.c | 86 +++++++++++++++++++++---------- 3 files changed, 87 insertions(+), 28 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/nrf/boards/pca10056/board.h b/hw/bsp/nrf/boards/pca10056/board.h index f4368f830..16d31addb 100644 --- a/hw/bsp/nrf/boards/pca10056/board.h +++ b/hw/bsp/nrf/boards/pca10056/board.h @@ -31,6 +31,8 @@ extern "C" { #endif +#define _PINNUM(port, pin) ((port)*32 + (pin)) + // LED #define LED_PIN 13 #define LED_STATE_ON 0 @@ -43,6 +45,13 @@ #define UART_RX_PIN 8 #define UART_TX_PIN 6 +// SPI for USB host shield +#define MAX3421E_SCK_PIN _PINNUM(1, 15) +#define MAX3421E_MOSI_PIN _PINNUM(1, 13) +#define MAX3421E_MISO_PIN _PINNUM(1, 14) +#define MAX3421E_CS_PIN _PINNUM(1, 12) +#define MAX3241E_INTR_PIN _PINNUM(1, 11) + #ifdef __cplusplus } #endif diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 368763b84..083efc235 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -107,7 +107,12 @@ void max3421e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { //--------------------------------------------------------------------+ void tuh_max3421e_int_api(uint8_t rhport, bool enabled) { (void) rhport; - nrfx_gpiote_trigger_enable(MAX3241E_INTR_PIN, enabled); + + if (enabled) { + nrfx_gpiote_trigger_enable(MAX3241E_INTR_PIN, true); + }else { + nrfx_gpiote_trigger_disable(MAX3241E_INTR_PIN); + } } void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { @@ -217,6 +222,19 @@ void board_init(void) { #endif #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 + // MAX3421 need 3.3v signal + if ((NRF_UICR->REGOUT0 & UICR_REGOUT0_VOUT_Msk) != UICR_REGOUT0_VOUT_3V3) { + NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen << NVMC_CONFIG_WEN_Pos; + while (NRF_NVMC->READY == NVMC_READY_READY_Busy){} + + NRF_UICR->REGOUT0 = (NRF_UICR->REGOUT0 & ~UICR_REGOUT0_VOUT_Msk) | UICR_REGOUT0_VOUT_3V3; + + NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Ren << NVMC_CONFIG_WEN_Pos; + while (NRF_NVMC->READY == NVMC_READY_READY_Busy){} + + NVIC_SystemReset(); + } + // manually manage CS nrf_gpio_cfg_output(MAX3421E_CS_PIN); tuh_max3421_spi_cs_api(0, false); diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 262dbca0f..cb7911992 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -184,8 +184,6 @@ typedef struct { } max3421_ep_t; typedef struct { - atomic_flag busy; // busy transferring - // cached register uint8_t sndbc; uint8_t hirq; @@ -194,7 +192,10 @@ typedef struct { uint8_t peraddr; uint8_t hxfr; + atomic_flag busy; // busy transferring + volatile uint8_t intr_disable_count; volatile uint16_t frame_count; + max3421_ep_t ep[CFG_TUH_MAX3421_ENDPOINT_TOTAL]; // [0] is reserved for addr0 OSAL_MUTEX_DEF(spi_mutexdef); @@ -220,8 +221,8 @@ void tuh_max3421e_int_api(uint8_t rhport, bool enabled); static void max3421_spi_lock(uint8_t rhport, bool in_isr) { // disable interrupt and mutex lock (for pre-emptive RTOS) if not in_isr if (!in_isr) { - tuh_max3421e_int_api(rhport, false); (void) osal_mutex_lock(_hcd_data.spi_mutex, OSAL_TIMEOUT_WAIT_FOREVER); + tuh_max3421e_int_api(rhport, false); } // assert CS @@ -294,6 +295,12 @@ static uint8_t reg_read(uint8_t rhport, uint8_t reg, bool in_isr) { return ret ? rx_buf[1] : 0; } +static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr) { + reg_write(rhport, HIRQ_ADDR, data, in_isr); + // HIRQ write 1 is clear + _hcd_data.hirq &= ~data; +} + static inline void hien_write(uint8_t rhport, uint8_t data, bool in_isr) { _hcd_data.hien = data; reg_write(rhport, HIEN_ADDR, data, in_isr); @@ -440,13 +447,14 @@ tusb_speed_t handle_connect_irq(uint8_t rhport) { bool hcd_init(uint8_t rhport) { (void) rhport; - hcd_int_disable(rhport); + tuh_max3421e_int_api(rhport, false); tuh_max3421_spi_cs_api(rhport, false); TU_LOG2_INT(sizeof(max3421_ep_t)); TU_LOG2_INT(sizeof(max3421_data_t)); tu_memclr(&_hcd_data, sizeof(_hcd_data)); + _hcd_data.peraddr = 0xff; // invalid #if OSAL_MUTEX_REQUIRED _hcd_data.spi_mutex = osal_mutex_create(&_hcd_data.spi_mutexdef); @@ -469,11 +477,13 @@ bool hcd_init(uint8_t rhport) { reg_write(rhport, HCTL_ADDR, HCTL_BUSRST | HCTL_FRMRST, false); // clear all previously pending IRQ - reg_write(rhport, HIRQ_ADDR, 0xff, false); + hirq_write(rhport, 0xff, false); // Enable IRQ hien_write(rhport, DEFAULT_HIEN, false); + tuh_max3421e_int_api(rhport, true); + // Enable Interrupt pin reg_write(rhport, CPUCTL_ADDR, CPUCTL_IE, false); @@ -481,13 +491,21 @@ bool hcd_init(uint8_t rhport) { } // Enable USB interrupt +// Not actually enable GPIO interrupt, just set variable to prevent handler to process void hcd_int_enable (uint8_t rhport) { - tuh_max3421e_int_api(rhport, true); + (void) rhport; + // tuh_max3421e_int_api(rhport, true); + if (_hcd_data.intr_disable_count) { + _hcd_data.intr_disable_count--; + } } // Disable USB interrupt +// Not actually disable GPIO interrupt, just set variable to prevent handler to process void hcd_int_disable(uint8_t rhport) { - tuh_max3421e_int_api(rhport, false); + (void) rhport; + //tuh_max3421e_int_api(rhport, false); + _hcd_data.intr_disable_count++; } // Get frame number (1ms) @@ -521,7 +539,7 @@ void hcd_port_reset_end(uint8_t rhport) { reg_write(rhport, HCTL_ADDR, 0, false); // Bus reset will also trigger CONDET IRQ, clear and re-enable it after reset - reg_write(rhport, HIRQ_ADDR, HIRQ_CONDET_IRQ, false); + hirq_write(rhport, HIRQ_CONDET_IRQ, false); hien_write(rhport, DEFAULT_HIEN, false); } @@ -572,19 +590,23 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * e void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { // Page 12: Programming BULK-OUT Transfers // TODO double buffered - if (switch_ep) { - peraddr_write(rhport, ep->daddr, in_isr); - - uint8_t const hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); - reg_write(rhport, HCTL_ADDR, hctl, in_isr); - } uint8_t hxfr = ep->ep_num | HXFR_OUT_NIN | (ep->is_iso ? HXFR_ISO : 0); - if (ep->ep_num == 0 && (ep->buf == NULL || ep->total_len == 0)) { // Control ZLP status use HS hxfr |= HXFR_HS; - } else { + } + + if (switch_ep) { + peraddr_write(rhport, ep->daddr, in_isr); + + if ( 0 == (hxfr & HXFR_HS) ) { + uint8_t const hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); + reg_write(rhport, HCTL_ADDR, hctl, in_isr); + } + } + + if ( 0 == (hxfr & HXFR_HS) ) { uint8_t const xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ,); if (xact_len) { @@ -598,12 +620,6 @@ void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { // Page 13: Programming BULK-IN Transfers - if (switch_ep) { - peraddr_write(rhport, ep->daddr, in_isr); - - uint8_t const hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); - reg_write(rhport, HCTL_ADDR, hctl, in_isr); - } uint8_t hxfr = ep->ep_num | (ep->is_iso ? HXFR_ISO : 0); if (ep->ep_num == 0 && (ep->buf == NULL || ep->total_len == 0)) { @@ -611,6 +627,15 @@ void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { hxfr |= HXFR_HS; } + if (switch_ep) { + peraddr_write(rhport, ep->daddr, in_isr); + + if ( 0 == (hxfr & HXFR_HS) ) { + uint8_t const hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); + reg_write(rhport, HCTL_ADDR, hctl, in_isr); + } + } + hxfr_write(rhport, hxfr, in_isr); } @@ -721,7 +746,7 @@ static void handle_xfer_done(uint8_t rhport) { xfer_result_t xfer_result; - //TU_LOG3("HRSL: %02X\r\n", hrsl); +// TU_LOG3("HRSL: %02X\r\n", hrsl); switch(hresult) { case HRSL_SUCCESS: xfer_result = XFER_RESULT_SUCCESS; @@ -821,13 +846,20 @@ void print_hirq(uint8_t hirq) { void hcd_int_handler(uint8_t rhport) { uint8_t hirq = reg_read(rhport, HIRQ_ADDR, true) & _hcd_data.hien; if (!hirq) return; - // print_hirq(hirq); if (hirq & HIRQ_FRAME_IRQ) { _hcd_data.frame_count++; } + // interrupt is disabled, only ack FRAME IRQ and skip the rest + if (_hcd_data.intr_disable_count) { + if (hirq & HIRQ_FRAME_IRQ) { + hirq_write(rhport, HIRQ_FRAME_IRQ, true); + } + return; + } + if (hirq & HIRQ_CONDET_IRQ) { tusb_speed_t speed = handle_connect_irq(rhport); @@ -861,7 +893,7 @@ void hcd_int_handler(uint8_t rhport) { } // ack RCVDVAV IRQ - reg_write(rhport, HIRQ_ADDR, HIRQ_RCVDAV_IRQ, true); + hirq_write(rhport, HIRQ_RCVDAV_IRQ, true); hirq = reg_read(rhport, HIRQ_ADDR, true); } @@ -871,7 +903,7 @@ void hcd_int_handler(uint8_t rhport) { } if ( hirq & HIRQ_HXFRDN_IRQ ) { - reg_write(rhport, HIRQ_ADDR, HIRQ_HXFRDN_IRQ, true); + hirq_write(rhport, HIRQ_HXFRDN_IRQ, true); handle_xfer_done(rhport); } @@ -881,7 +913,7 @@ void hcd_int_handler(uint8_t rhport) { // clear all interrupt except SNDBAV_IRQ (never clear by us). Note RCVDAV_IRQ, HXFRDN_IRQ already clear while processing hirq &= ~HIRQ_SNDBAV_IRQ; if ( hirq ) { - reg_write(rhport, HIRQ_ADDR, hirq, true); + hirq_write(rhport, hirq, true); } } -- cgit v1.3.1 From 2a814a99af32bf084cbb730d97e3c9cb31a3fa85 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 29 Aug 2023 20:27:37 +0700 Subject: - hcd_setup_send() also check for busy flag - xact_inout() to support send setup --- src/portable/analog/max3421/hcd_max3421.c | 71 +++++++++++++++++-------------- 1 file changed, 39 insertions(+), 32 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index cb7911992..461e02593 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -168,6 +168,7 @@ typedef struct { struct TU_ATTR_PACKED { uint8_t ep_dir : 1; uint8_t is_iso : 1; + uint8_t is_setup : 1; uint8_t data_toggle : 1; uint8_t xfer_pending : 1; uint8_t xfer_complete : 1; @@ -590,56 +591,55 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * e void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { // Page 12: Programming BULK-OUT Transfers // TODO double buffered - - uint8_t hxfr = ep->ep_num | HXFR_OUT_NIN | (ep->is_iso ? HXFR_ISO : 0); - if (ep->ep_num == 0 && (ep->buf == NULL || ep->total_len == 0)) { - // Control ZLP status use HS - hxfr |= HXFR_HS; - } - if (switch_ep) { peraddr_write(rhport, ep->daddr, in_isr); - if ( 0 == (hxfr & HXFR_HS) ) { - uint8_t const hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); - reg_write(rhport, HCTL_ADDR, hctl, in_isr); - } + uint8_t const hctl = (ep->data_toggle ? HCTL_SNDTOG1 : HCTL_SNDTOG0); + reg_write(rhport, HCTL_ADDR, hctl, in_isr); } - if ( 0 == (hxfr & HXFR_HS) ) { - uint8_t const xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); - TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ,); - if (xact_len) { - fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, in_isr); - } - sndbc_write(rhport, xact_len, in_isr); + uint8_t const xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); + TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ,); + if (xact_len) { + fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, in_isr); } + sndbc_write(rhport, xact_len, in_isr); + uint8_t hxfr = ep->ep_num | HXFR_OUT_NIN | (ep->is_iso ? HXFR_ISO : 0); hxfr_write(rhport, hxfr, in_isr); } void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { // Page 13: Programming BULK-IN Transfers - - uint8_t hxfr = ep->ep_num | (ep->is_iso ? HXFR_ISO : 0); - if (ep->ep_num == 0 && (ep->buf == NULL || ep->total_len == 0)) { - // Control ZLP status use HS - hxfr |= HXFR_HS; - } - if (switch_ep) { peraddr_write(rhport, ep->daddr, in_isr); - if ( 0 == (hxfr & HXFR_HS) ) { - uint8_t const hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); - reg_write(rhport, HCTL_ADDR, hctl, in_isr); - } + uint8_t const hctl = (ep->data_toggle ? HCTL_RCVTOG1 : HCTL_RCVTOG0); + reg_write(rhport, HCTL_ADDR, hctl, in_isr); } + uint8_t hxfr = ep->ep_num | (ep->is_iso ? HXFR_ISO : 0); hxfr_write(rhport, hxfr, in_isr); } TU_ATTR_ALWAYS_INLINE static inline void xact_inout(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { + if (ep->ep_num == 0 ) { + // setup + if (ep->is_setup) { + peraddr_write(rhport, ep->daddr, in_isr); + hxfr_write(rhport, HXFR_SETUP, in_isr); + return; + } + + // status + if (ep->buf == NULL || ep->total_len == 0) { + uint8_t const hxfr = HXFR_HS | (ep->ep_dir ? 0 : HXFR_OUT_NIN); + peraddr_write(rhport, ep->daddr, in_isr); + hxfr_write(rhport, hxfr, in_isr); + return; + } + } + if (ep->ep_dir) { xact_in(rhport, ep, switch_ep, in_isr); }else { @@ -665,12 +665,15 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->xfer_pending = 1; if ( ep_num == 0 ) { + ep->is_setup = 0; ep->data_toggle = 1; } // carry out transfer if not busy if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { xact_inout(rhport, ep, true, false); + } else { + return true; } return true; @@ -694,12 +697,16 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] TU_ASSERT(ep); ep->ep_dir = 0; - ep->total_len = 8; + ep->total_len = 8; ep->xferred_len = 0; + ep->is_setup = 1; - peraddr_write(rhport, daddr, false); fifo_write(rhport, SUDFIFO_ADDR, setup_packet, 8, false); - hxfr_write(rhport, HXFR_SETUP, false); + + // carry out transfer if not busy + if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { + xact_inout(rhport, ep, true, false); + } return true; } -- cgit v1.3.1 From 1ab488eb06ef4cb8ad9c0cff91e6b0caf76f73c4 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 30 Aug 2023 16:04:18 +0700 Subject: call xfer_complete_isr() when result is not successful (stalled or failed) --- hw/bsp/nrf/boards/pca10095/board.h | 9 +++++++ hw/bsp/nrf/family.c | 7 +++-- hw/bsp/nrf/nrfx_config.h | 2 +- src/common/tusb_mcu.h | 2 +- src/portable/analog/max3421/hcd_max3421.c | 43 ++++++++++++++++++++++--------- 5 files changed, 47 insertions(+), 16 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/nrf/boards/pca10095/board.h b/hw/bsp/nrf/boards/pca10095/board.h index fd3c63d6a..b9d3a19dc 100644 --- a/hw/bsp/nrf/boards/pca10095/board.h +++ b/hw/bsp/nrf/boards/pca10095/board.h @@ -31,6 +31,8 @@ extern "C" { #endif +#define _PINNUM(port, pin) ((port)*32 + (pin)) + // LED #define LED_PIN 28 #define LED_STATE_ON 0 @@ -43,6 +45,13 @@ #define UART_RX_PIN 32 #define UART_TX_PIN 33 +// SPI for USB host shield +#define MAX3421E_SCK_PIN _PINNUM(1, 15) +#define MAX3421E_MOSI_PIN _PINNUM(1, 13) +#define MAX3421E_MISO_PIN _PINNUM(1, 14) +#define MAX3421E_CS_PIN _PINNUM(1, 12) +#define MAX3241E_INTR_PIN _PINNUM(1, 11) + #ifdef __cplusplus } #endif diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 083efc235..2b4260083 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -34,6 +34,7 @@ #pragma GCC diagnostic ignored "-Wcast-align" #pragma GCC diagnostic ignored "-Wunused-parameter" #pragma GCC diagnostic ignored "-Wundef" +#pragma GCC diagnostic ignored "-Wredundant-decls" #endif #include "nrfx.h" @@ -94,7 +95,7 @@ TU_ATTR_UNUSED static void power_event_handler(nrfx_power_usb_evt_t event) { //------------- Host using MAX2341E -------------// #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 -static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(0); +static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(1); void max3421e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { if ( !(pin == MAX3241E_INTR_PIN && action == NRF_GPIOTE_POLARITY_HITOLO) ) return; @@ -222,7 +223,8 @@ void board_init(void) { #endif #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 - // MAX3421 need 3.3v signal + // MAX3421 need 3.3v signal (may not be needed) + #if defined(UICR_REGOUT0_VOUT_Msk) && 0 if ((NRF_UICR->REGOUT0 & UICR_REGOUT0_VOUT_Msk) != UICR_REGOUT0_VOUT_3V3) { NRF_NVMC->CONFIG = NVMC_CONFIG_WEN_Wen << NVMC_CONFIG_WEN_Pos; while (NRF_NVMC->READY == NVMC_READY_READY_Busy){} @@ -234,6 +236,7 @@ void board_init(void) { NVIC_SystemReset(); } + #endif // manually manage CS nrf_gpio_cfg_output(MAX3421E_CS_PIN); diff --git a/hw/bsp/nrf/nrfx_config.h b/hw/bsp/nrf/nrfx_config.h index e3d0ea91b..95ef33ce4 100644 --- a/hw/bsp/nrf/nrfx_config.h +++ b/hw/bsp/nrf/nrfx_config.h @@ -11,7 +11,7 @@ #define NRFX_UARTE0_ENABLED 1 #define NRFX_SPIM_ENABLED 1 -#define NRFX_SPIM0_ENABLED 1 +#define NRFX_SPIM1_ENABLED 1 // use SPI1 since nrf5340 share uart with spi #define NRFX_PRS_ENABLED 0 #define NRFX_USBREG_ENABLED 1 diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 21939df7c..8807ff8aa 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -390,7 +390,7 @@ // External USB controller //--------------------------------------------------------------------+ -#if defined(CFG_TUH_MAX3421) & CFG_TUH_MAX3421 +#if defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 #ifndef CFG_TUH_MAX3421_ENDPOINT_TOTAL #define CFG_TUH_MAX3421_ENDPOINT_TOTAL (8 + 4*(CFG_TUH_DEVICE_MAX-1)) #endif diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 461e02593..705bb5bfd 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -374,7 +374,8 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // starting from next endpoint for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->xfer_pending) { + if (ep->xfer_pending && ep->packet_size) { +// TU_LOG3("next pending i = %u\n", i); return ep; } } @@ -382,7 +383,8 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // wrap around including current endpoint for (size_t i = 0; i <= idx; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->xfer_pending) { + if (ep->xfer_pending && ep->packet_size) { +// TU_LOG3("next pending i = %u\n", i); return ep; } } @@ -464,6 +466,10 @@ bool hcd_init(uint8_t rhport) { // full duplex, interrupt negative edge reg_write(rhport, PINCTL_ADDR, PINCTL_FDUPSPI, false); + // V1 is 0x01, V2 is 0x12, V3 is 0x13 + // uint8_t const revision = reg_read(rhport, REVISION_ADDR, false); + // TU_LOG2_HEX(revision); + // reset reg_write(rhport, USBCTL_ADDR, USBCTL_CHIPRES, false); reg_write(rhport, USBCTL_ADDR, 0, false); @@ -699,6 +705,7 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] ep->ep_dir = 0; ep->total_len = 8; ep->xferred_len = 0; + ep->xfer_pending = 1; ep->is_setup = 1; fifo_write(rhport, SUDFIFO_ADDR, setup_packet, 8, false); @@ -724,9 +731,16 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { // Interrupt Handler //--------------------------------------------------------------------+ -static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t result, uint8_t data_toggle) { +static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t result, uint8_t hrsl) { uint8_t const ep_addr = tu_edpt_addr(ep->ep_num, ep->ep_dir); - ep->data_toggle = data_toggle; + + // save data toggle + if (ep->ep_dir) { + ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; + }else { + ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; + } + ep->xfer_pending = 0; hcd_event_xfer_complete(ep->daddr, ep_addr, ep->xferred_len, result, true); @@ -763,10 +777,6 @@ static void handle_xfer_done(uint8_t rhport) { xfer_result = XFER_RESULT_STALLED; break; - case HRSL_BAD_REQ: - // occurred when initialized without any pending transfer. Skip for now - return; - case HRSL_NAK: if (ep_num == 0) { // NAK on control, retry immediately @@ -781,15 +791,26 @@ static void handle_xfer_done(uint8_t rhport) { }else if (next_ep) { // switch to next pending TODO could have issue with double buffered if not clear previously out data xact_inout(rhport, next_ep, true, true); + }else { + TU_ASSERT(false,); } } return; + case HRSL_BAD_REQ: + // occurred when initialized without any pending transfer. Skip for now + return; + default: xfer_result = XFER_RESULT_FAILED; break; } + if (xfer_result != XFER_RESULT_SUCCESS) { + xfer_complete_isr(rhport, ep, xfer_result, hrsl); + return; + } + if (ep_dir) { // IN transfer: fifo data is already received in RCVDAV IRQ if ( hxfr_type & HXFR_HS ) { @@ -798,8 +819,7 @@ static void handle_xfer_done(uint8_t rhport) { // short packet or all bytes transferred if ( ep->xfer_complete ) { - uint8_t const dt = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; // save data toggle - xfer_complete_isr(rhport, ep, xfer_result, dt); + xfer_complete_isr(rhport, ep, xfer_result, hrsl); }else { // more to transfer hxfr_write(rhport, _hcd_data.hxfr, true); @@ -820,8 +840,7 @@ static void handle_xfer_done(uint8_t rhport) { ep->buf += xact_len; if (xact_len < ep->packet_size || ep->xferred_len >= ep->total_len) { - uint8_t const dt = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; // save data toggle - xfer_complete_isr(rhport, ep, xfer_result, dt); + xfer_complete_isr(rhport, ep, xfer_result, hrsl); } else { // more to transfer xact_out(rhport, ep, false, true); -- cgit v1.3.1 From 41493426b38c8ce44b1f7720b907538bc5402f98 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 30 Aug 2023 16:21:43 +0700 Subject: use ep buf to keep setup packet, work well with hid device --- examples/host/msc_file_explorer/src/tusb_config.h | 2 +- src/portable/analog/max3421/hcd_max3421.c | 7 ++++--- 2 files changed, 5 insertions(+), 4 deletions(-) (limited to 'src/portable') diff --git a/examples/host/msc_file_explorer/src/tusb_config.h b/examples/host/msc_file_explorer/src/tusb_config.h index 28e130c0e..e6186ba46 100644 --- a/examples/host/msc_file_explorer/src/tusb_config.h +++ b/examples/host/msc_file_explorer/src/tusb_config.h @@ -37,7 +37,7 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // change to 1 if using pico-pio-usb as host controller for raspberry rp2040 #define CFG_TUH_RPI_PIO_USB 0 - #define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_US + #define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB //#elif CFG_TUSB_MCU == OPT_MCU_NRF5X // // Use external USB controller (via SPI) MAX3421E (aka usb host shield) // #define CFG_TUH_MAX3421 1 diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 705bb5bfd..d644390da 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -633,6 +633,7 @@ TU_ATTR_ALWAYS_INLINE static inline void xact_inout(uint8_t rhport, max3421_ep_t // setup if (ep->is_setup) { peraddr_write(rhport, ep->daddr, in_isr); + fifo_write(rhport, SUDFIFO_ADDR, ep->buf, 8, in_isr); hxfr_write(rhport, HXFR_SETUP, in_isr); return; } @@ -703,12 +704,12 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] TU_ASSERT(ep); ep->ep_dir = 0; + ep->is_setup = 1; + ep->buf = (uint8_t*)(uintptr_t) setup_packet; ep->total_len = 8; ep->xferred_len = 0; + ep->xfer_complete = 0; ep->xfer_pending = 1; - ep->is_setup = 1; - - fifo_write(rhport, SUDFIFO_ADDR, setup_packet, 8, false); // carry out transfer if not busy if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { -- cgit v1.3.1 From 3b7d5aa0421f3d3a7ac199de0138dc40141fbddd Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 31 Aug 2023 16:52:09 +0700 Subject: improve connection & disconnection detection. But there is still issue when CONDETIRQ occurs but we are disabled interrupt (for osal queue access). --- hw/bsp/board.c | 26 ++++------ hw/bsp/nrf/family.c | 49 ++++++++---------- src/host/usbh.c | 2 +- src/portable/analog/max3421/hcd_max3421.c | 85 ++++++++++++++----------------- 4 files changed, 72 insertions(+), 90 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/board.c b/hw/bsp/board.c index 417630a03..562792625 100644 --- a/hw/bsp/board.c +++ b/hw/bsp/board.c @@ -44,17 +44,16 @@ // If using SES IDE, use the Syscalls/SEGGER_RTT_Syscalls_SES.c instead #if !(defined __SES_ARM) && !(defined __SES_RISCV) && !(defined __CROSSWORKS_ARM) + #include "SEGGER_RTT.h" -TU_ATTR_USED int sys_write (int fhdl, const void *buf, size_t count) -{ +TU_ATTR_USED int sys_write(int fhdl, const void *buf, size_t count) { (void) fhdl; - SEGGER_RTT_Write(0, (const char*) buf, (int) count); + SEGGER_RTT_Write(0, (const char *) buf, (int) count); return count; } -TU_ATTR_USED int sys_read (int fhdl, char *buf, size_t count) -{ +TU_ATTR_USED int sys_read(int fhdl, char *buf, size_t count) { (void) fhdl; int rd = (int) SEGGER_RTT_Read(0, buf, count); return (rd > 0) ? rd : -1; @@ -67,8 +66,7 @@ TU_ATTR_USED int sys_read (int fhdl, char *buf, size_t count) #include "board_mcu.h" -TU_ATTR_USED int sys_write (int fhdl, const void *buf, size_t count) -{ +TU_ATTR_USED int sys_write (int fhdl, const void *buf, size_t count) { (void) fhdl; uint8_t const* buf8 = (uint8_t const*) buf; @@ -79,8 +77,7 @@ TU_ATTR_USED int sys_write (int fhdl, const void *buf, size_t count) return (int) count; } -TU_ATTR_USED int sys_read (int fhdl, char *buf, size_t count) -{ +TU_ATTR_USED int sys_read (int fhdl, char *buf, size_t count) { (void) fhdl; (void) buf; (void) count; @@ -90,14 +87,12 @@ TU_ATTR_USED int sys_read (int fhdl, char *buf, size_t count) #else // Default logging with on-board UART -TU_ATTR_USED int sys_write (int fhdl, const void *buf, size_t count) -{ +TU_ATTR_USED int sys_write (int fhdl, const void *buf, size_t count) { (void) fhdl; return board_uart_write(buf, (int) count); } -TU_ATTR_USED int sys_read (int fhdl, char *buf, size_t count) -{ +TU_ATTR_USED int sys_read (int fhdl, char *buf, size_t count) { (void) fhdl; int rd = board_uart_read((uint8_t*) buf, (int) count); return (rd > 0) ? rd : -1; @@ -105,8 +100,7 @@ TU_ATTR_USED int sys_read (int fhdl, char *buf, size_t count) #endif -int board_getchar(void) -{ +int board_getchar(void) { char c; - return ( sys_read(0, &c, 1) > 0 ) ? (int) c : (-1); + return (sys_read(0, &c, 1) > 0) ? (int) c : (-1); } diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 2b4260083..7358458ce 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -98,7 +98,7 @@ TU_ATTR_UNUSED static void power_event_handler(nrfx_power_usb_evt_t event) { static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(1); void max3421e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { - if ( !(pin == MAX3241E_INTR_PIN && action == NRF_GPIOTE_POLARITY_HITOLO) ) return; + if (!(pin == MAX3241E_INTR_PIN && action == NRF_GPIOTE_POLARITY_HITOLO)) return; tuh_int_handler(1); } @@ -111,7 +111,7 @@ void tuh_max3421e_int_api(uint8_t rhport, bool enabled) { if (enabled) { nrfx_gpiote_trigger_enable(MAX3241E_INTR_PIN, true); - }else { + } else { nrfx_gpiote_trigger_disable(MAX3241E_INTR_PIN); } } @@ -121,7 +121,7 @@ void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { nrf_gpio_pin_write(MAX3421E_CS_PIN, active ? 0 : 1); } -bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len) { +bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_len, uint8_t *rx_buf, size_t rx_len) { (void) rhport; nrfx_spim_xfer_desc_t xfer = { @@ -157,21 +157,21 @@ void board_init(void) { nrf_gpio_cfg_input(BUTTON_PIN, NRF_GPIO_PIN_PULLUP); // 1ms tick timer - SysTick_Config(SystemCoreClock/1000); + SysTick_Config(SystemCoreClock / 1000); // UART nrfx_uarte_config_t uart_cfg = { - .pseltxd = UART_TX_PIN, - .pselrxd = UART_RX_PIN, - .pselcts = NRF_UARTE_PSEL_DISCONNECTED, - .pselrts = NRF_UARTE_PSEL_DISCONNECTED, - .p_context = NULL, - .baudrate = NRF_UARTE_BAUDRATE_115200, // CFG_BOARD_UART_BAUDRATE - .interrupt_priority = 7, - .hal_cfg = { - .hwfc = NRF_UARTE_HWFC_DISABLED, - .parity = NRF_UARTE_PARITY_EXCLUDED, - } + .pseltxd = UART_TX_PIN, + .pselrxd = UART_RX_PIN, + .pselcts = NRF_UARTE_PSEL_DISCONNECTED, + .pselrts = NRF_UARTE_PSEL_DISCONNECTED, + .p_context = NULL, + .baudrate = NRF_UARTE_BAUDRATE_115200, // CFG_BOARD_UART_BAUDRATE + .interrupt_priority = 7, + .hal_cfg = { + .hwfc = NRF_UARTE_HWFC_DISABLED, + .parity = NRF_UARTE_PARITY_EXCLUDED, + } }; nrfx_uarte_init(&_uart_id, &uart_cfg, NULL); //uart_handler); @@ -211,11 +211,11 @@ void board_init(void) { // USB power may already be ready at this time -> no event generated // We need to invoke the handler based on the status initially - #ifdef NRF5340_XXAA +#ifdef NRF5340_XXAA usb_reg = NRF_USBREGULATOR->USBREGSTATUS; - #else +#else usb_reg = NRF_POWER->USBREGSTATUS; - #endif +#endif } if ( usb_reg & VBUSDETECT_Msk ) tusb_hal_nrf_power_event(USB_EVT_DETECTED); @@ -308,8 +308,7 @@ uint32_t board_millis(void) { #ifdef SOFTDEVICE_PRESENT // process SOC event from SD -uint32_t proc_soc(void) -{ +uint32_t proc_soc(void) { uint32_t soc_evt; uint32_t err = sd_evt_get(&soc_evt); @@ -326,18 +325,14 @@ uint32_t proc_soc(void) return err; } -uint32_t proc_ble(void) -{ +uint32_t proc_ble(void) { // do nothing with ble return NRF_ERROR_NOT_FOUND; } -void SD_EVT_IRQHandler(void) -{ +void SD_EVT_IRQHandler(void) { // process BLE and SOC until there is no more events - while( (NRF_ERROR_NOT_FOUND != proc_ble()) || (NRF_ERROR_NOT_FOUND != proc_soc()) ) - { - + while( (NRF_ERROR_NOT_FOUND != proc_ble()) || (NRF_ERROR_NOT_FOUND != proc_soc()) ) { } } diff --git a/src/host/usbh.c b/src/host/usbh.c index 12a7f5839..bacb3a719 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -852,7 +852,7 @@ bool usbh_edpt_xfer_with_callback(uint8_t dev_addr, uint8_t ep_addr, uint8_t * b ep_state->busy = 0; ep_state->claimed = 0; TU_LOG1("Failed\r\n"); - TU_BREAKPOINT(); +// TU_BREAKPOINT(); return false; } } diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index d644390da..56d3aea45 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -405,45 +405,46 @@ bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { return false; } -tusb_speed_t handle_connect_irq(uint8_t rhport) { +static void handle_connect_irq(uint8_t rhport) { uint8_t const hrsl = reg_read(rhport, HRSL_ADDR, true); uint8_t const jk = hrsl & (HRSL_JSTATUS | HRSL_KSTATUS); - tusb_speed_t speed; uint8_t new_mode = MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST; + TU_LOG2_HEX(jk); switch(jk) { - case 0x00: - // SEO is disconnected - speed = TUSB_SPEED_INVALID; - break; - - case (HRSL_JSTATUS | HRSL_KSTATUS): - // SE1 is illegal - speed = TUSB_SPEED_INVALID; + case 0x00: // SEO is disconnected + case (HRSL_JSTATUS | HRSL_KSTATUS): // SE1 is illegal + mode_write(rhport, new_mode, true); + hcd_event_device_remove(rhport, true); break; default: { - // Low speed if (LS = 1 and J-state) or (LS = 0 and K-State) - uint8_t const mode = reg_read(rhport, MODE_ADDR, true); - uint8_t const ls_bit = mode & MODE_LOWSPEED; + // Bus Reset also cause CONDET IRQ, skip if we are already connected and doing bus reset + if ((_hcd_data.hirq & HIRQ_BUSEVENT_IRQ) && (_hcd_data.mode & MODE_SOFKAENAB)) { + break; + } - if ( (ls_bit && (jk == HRSL_JSTATUS)) || (!ls_bit && (jk == HRSL_KSTATUS)) ) { - speed = TUSB_SPEED_LOW; + // Low speed if (LS = 1 and J-state) or (LS = 0 and K-State) + // However, since we are always in full speed mode, we can just check J-state + if (jk == HRSL_KSTATUS) { new_mode |= MODE_LOWSPEED; - } else { - speed = TUSB_SPEED_FULL; + TU_LOG3("Low speed\n"); + }else { + TU_LOG3("Full speed\n"); } + new_mode |= MODE_SOFKAENAB; + mode_write(rhport, new_mode, true); - new_mode |= MODE_SOFKAENAB; // enable SOF since there is new device + // FIXME multiple MAX3421 rootdevice address is not 1 + uint8_t const daddr = 1; + free_ep(daddr); + + hcd_event_device_attach(rhport, true); break; } } - - mode_write(rhport, new_mode, true); - TU_LOG2_INT(speed); - return speed; } // Initialize controller to host mode @@ -500,8 +501,9 @@ bool hcd_init(uint8_t rhport) { // Enable USB interrupt // Not actually enable GPIO interrupt, just set variable to prevent handler to process void hcd_int_enable (uint8_t rhport) { +// tuh_max3421e_int_api(rhport, true); + (void) rhport; - // tuh_max3421e_int_api(rhport, true); if (_hcd_data.intr_disable_count) { _hcd_data.intr_disable_count--; } @@ -510,8 +512,8 @@ void hcd_int_enable (uint8_t rhport) { // Disable USB interrupt // Not actually disable GPIO interrupt, just set variable to prevent handler to process void hcd_int_disable(uint8_t rhport) { - (void) rhport; //tuh_max3421e_int_api(rhport, false); + (void) rhport; _hcd_data.intr_disable_count++; } @@ -534,20 +536,12 @@ bool hcd_port_connect_status(uint8_t rhport) { // Reset USB bus on the port. Return immediately, bus reset sequence may not be complete. // Some port would require hcd_port_reset_end() to be invoked after 10ms to complete the reset sequence. void hcd_port_reset(uint8_t rhport) { - // Bus reset will also trigger CONDET IRQ, disable it - uint8_t const hien = DEFAULT_HIEN & ~HIRQ_CONDET_IRQ; - hien_write(rhport, hien, false); - reg_write(rhport, HCTL_ADDR, HCTL_BUSRST, false); } // Complete bus reset sequence, may be required by some controllers void hcd_port_reset_end(uint8_t rhport) { reg_write(rhport, HCTL_ADDR, 0, false); - - // Bus reset will also trigger CONDET IRQ, clear and re-enable it after reset - hirq_write(rhport, HIRQ_CONDET_IRQ, false); - hien_write(rhport, DEFAULT_HIEN, false); } // Get port link speed @@ -660,7 +654,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf uint8_t const ep_dir = tu_edpt_dir(ep_addr); max3421_ep_t* ep = find_opened_ep(daddr, ep_num, ep_dir); - TU_ASSERT(ep); + TU_VERIFY(ep); // control transfer can switch direction ep->ep_dir = ep_dir; @@ -767,8 +761,6 @@ static void handle_xfer_done(uint8_t rhport) { TU_ASSERT(ep, ); xfer_result_t xfer_result; - -// TU_LOG3("HRSL: %02X\r\n", hrsl); switch(hresult) { case HRSL_SUCCESS: xfer_result = XFER_RESULT_SUCCESS; @@ -803,6 +795,7 @@ static void handle_xfer_done(uint8_t rhport) { return; default: + TU_LOG3("HRSL: %02X\r\n", hrsl); xfer_result = XFER_RESULT_FAILED; break; } @@ -875,30 +868,30 @@ void hcd_int_handler(uint8_t rhport) { if (!hirq) return; // print_hirq(hirq); +// uint8_t hirq = reg_read(rhport, HIRQ_ADDR, true); + if (hirq & HIRQ_FRAME_IRQ) { _hcd_data.frame_count++; } + #if 1 // interrupt is disabled, only ack FRAME IRQ and skip the rest if (_hcd_data.intr_disable_count) { if (hirq & HIRQ_FRAME_IRQ) { hirq_write(rhport, HIRQ_FRAME_IRQ, true); } + + if ((hirq & HIRQ_CONDET_IRQ) && !(_hcd_data.mode & MODE_SOFKAENAB)) { + // connection when interrupt is disabled + TU_LOG3_INT(_hcd_data.intr_disable_count); + return; + } return; } + #endif if (hirq & HIRQ_CONDET_IRQ) { - tusb_speed_t speed = handle_connect_irq(rhport); - - if (speed == TUSB_SPEED_INVALID) { - hcd_event_device_remove(rhport, true); - }else { - // FIXME multiple MAX3421 rootdevice address is not 1 - uint8_t const daddr = 1; - free_ep(daddr); - - hcd_event_device_attach(rhport, true); - } + handle_connect_irq(rhport); } // queue more transfer in handle_xfer_done() can cause hirq to be set again while external IRQ may not catch and/or -- cgit v1.3.1 From ed0a233d4830baa8a767fcc20dcbfedbb09b7b41 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 31 Aug 2023 21:28:27 +0700 Subject: vastly improve attach/detach device, still have issue where thing is still hanged occasionally. --- src/portable/analog/max3421/hcd_max3421.c | 126 +++++++++++++++++------------- 1 file changed, 70 insertions(+), 56 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 56d3aea45..c61389cb9 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -215,6 +215,9 @@ void tuh_max3421_spi_cs_api(uint8_t rhport, bool active); bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len); void tuh_max3421e_int_api(uint8_t rhport, bool enabled); +static void handle_connect_irq(uint8_t rhport, bool in_isr); +static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr); + //--------------------------------------------------------------------+ // SPI Helper //--------------------------------------------------------------------+ @@ -238,6 +241,14 @@ static void max3421_spi_unlock(uint8_t rhport, bool in_isr) { if (!in_isr) { tuh_max3421e_int_api(rhport, true); (void) osal_mutex_unlock(_hcd_data.spi_mutex); + + // when re-enable interrupt, we may miss INTR edge (usually via GPIO detection interrupt). + // It would be ok if we are operating since SOF will re-trigger interrupt. + // However, for CONDET_IRQ i.e host not operating therefore we need to manually handle it here. + if (_hcd_data.hirq & HIRQ_CONDET_IRQ) { + handle_connect_irq(rhport, false); + hirq_write(rhport, HIRQ_CONDET_IRQ, false); + } } } @@ -405,48 +416,6 @@ bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { return false; } -static void handle_connect_irq(uint8_t rhport) { - uint8_t const hrsl = reg_read(rhport, HRSL_ADDR, true); - uint8_t const jk = hrsl & (HRSL_JSTATUS | HRSL_KSTATUS); - - uint8_t new_mode = MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST; - TU_LOG2_HEX(jk); - - switch(jk) { - case 0x00: // SEO is disconnected - case (HRSL_JSTATUS | HRSL_KSTATUS): // SE1 is illegal - mode_write(rhport, new_mode, true); - hcd_event_device_remove(rhport, true); - break; - - default: { - // Bus Reset also cause CONDET IRQ, skip if we are already connected and doing bus reset - if ((_hcd_data.hirq & HIRQ_BUSEVENT_IRQ) && (_hcd_data.mode & MODE_SOFKAENAB)) { - break; - } - - // Low speed if (LS = 1 and J-state) or (LS = 0 and K-State) - // However, since we are always in full speed mode, we can just check J-state - if (jk == HRSL_KSTATUS) { - new_mode |= MODE_LOWSPEED; - TU_LOG3("Low speed\n"); - }else { - TU_LOG3("Full speed\n"); - } - new_mode |= MODE_SOFKAENAB; - mode_write(rhport, new_mode, true); - - // FIXME multiple MAX3421 rootdevice address is not 1 - uint8_t const daddr = 1; - free_ep(daddr); - - hcd_event_device_attach(rhport, true); - - break; - } - } -} - // Initialize controller to host mode bool hcd_init(uint8_t rhport) { (void) rhport; @@ -507,6 +476,14 @@ void hcd_int_enable (uint8_t rhport) { if (_hcd_data.intr_disable_count) { _hcd_data.intr_disable_count--; } + + // when re-enable interrupt, we may miss INTR edge (usually via GPIO detection interrupt). + // It would be ok if we are operating since SOF will re-trigger interrupt. + // However, for CONDET_IRQ i.e host not operating therefore we need to manually handle it here. +// if (_hcd_data.hirq & HIRQ_CONDET_IRQ) { +// handle_connect_irq(rhport, false); +// hirq_write(rhport, HIRQ_CONDET_IRQ, false); +// } } // Disable USB interrupt @@ -726,6 +703,54 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { // Interrupt Handler //--------------------------------------------------------------------+ +static void handle_connect_irq(uint8_t rhport, bool in_isr) { + uint8_t const hrsl = reg_read(rhport, HRSL_ADDR, in_isr); + uint8_t const jk = hrsl & (HRSL_JSTATUS | HRSL_KSTATUS); + + uint8_t new_mode = MODE_DPPULLDN | MODE_DMPULLDN | MODE_HOST; + TU_LOG2_HEX(jk); + + switch(jk) { + case 0x00: // SEO is disconnected + case (HRSL_JSTATUS | HRSL_KSTATUS): // SE1 is illegal + mode_write(rhport, new_mode, in_isr); + + // port reset anyway, this will help to stable bus signal for next connection + reg_write(rhport, HCTL_ADDR, HCTL_BUSRST, in_isr); + + hcd_event_device_remove(rhport, in_isr); + + reg_write(rhport, HCTL_ADDR, 0, in_isr); + break; + + default: { + // Bus Reset also cause CONDET IRQ, skip if we are already connected and doing bus reset + if ((_hcd_data.hirq & HIRQ_BUSEVENT_IRQ) && (_hcd_data.mode & MODE_SOFKAENAB)) { + break; + } + + // Low speed if (LS = 1 and J-state) or (LS = 0 and K-State) + // However, since we are always in full speed mode, we can just check J-state + if (jk == HRSL_KSTATUS) { + new_mode |= MODE_LOWSPEED; + TU_LOG3("Low speed\n"); + }else { + TU_LOG3("Full speed\n"); + } + new_mode |= MODE_SOFKAENAB; + mode_write(rhport, new_mode, in_isr); + + // FIXME multiple MAX3421 rootdevice address is not 1 + uint8_t const daddr = 1; + free_ep(daddr); + + hcd_event_device_attach(rhport, in_isr); + + break; + } + } +} + static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t result, uint8_t hrsl) { uint8_t const ep_addr = tu_edpt_addr(ep->ep_num, ep->ep_dir); @@ -758,7 +783,7 @@ static void handle_xfer_done(uint8_t rhport) { uint8_t const ep_dir = ((hxfr_type & HXFR_SETUP) || (hxfr_type & HXFR_OUT_NIN)) ? 0 : 1; max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, ep_dir); - TU_ASSERT(ep, ); + TU_VERIFY(ep, ); xfer_result_t xfer_result; switch(hresult) { @@ -857,7 +882,6 @@ void print_hirq(uint8_t hirq) { TU_LOG3("\r\n"); } - #else #define print_hirq(hirq) #endif @@ -868,30 +892,20 @@ void hcd_int_handler(uint8_t rhport) { if (!hirq) return; // print_hirq(hirq); -// uint8_t hirq = reg_read(rhport, HIRQ_ADDR, true); - if (hirq & HIRQ_FRAME_IRQ) { _hcd_data.frame_count++; } - #if 1 - // interrupt is disabled, only ack FRAME IRQ and skip the rest + // interrupt is disabled by usbh task: only ack FRAME IRQ and skip the rest if (_hcd_data.intr_disable_count) { if (hirq & HIRQ_FRAME_IRQ) { hirq_write(rhport, HIRQ_FRAME_IRQ, true); } - - if ((hirq & HIRQ_CONDET_IRQ) && !(_hcd_data.mode & MODE_SOFKAENAB)) { - // connection when interrupt is disabled - TU_LOG3_INT(_hcd_data.intr_disable_count); - return; - } return; } - #endif if (hirq & HIRQ_CONDET_IRQ) { - handle_connect_irq(rhport); + handle_connect_irq(rhport, true); } // queue more transfer in handle_xfer_done() can cause hirq to be set again while external IRQ may not catch and/or -- cgit v1.3.1 From 21ab40bab2e2fee28fa595f648a17944696c3d65 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 7 Sep 2023 12:38:18 +0700 Subject: - wrap up hcd max3421, work well with nrf52840 - also add usbh_defer_func() --- hw/bsp/nrf/family.c | 7 ++++-- src/host/usbh.c | 26 ++++++++++++---------- src/host/usbh_pvt.h | 10 ++++----- src/portable/analog/max3421/hcd_max3421.c | 36 ++----------------------------- 4 files changed, 27 insertions(+), 52 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 7358458ce..39ce179e8 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -109,10 +109,12 @@ void max3421e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { void tuh_max3421e_int_api(uint8_t rhport, bool enabled) { (void) rhport; + // use NVIC_Enable/Disable instead since nrfx_gpiote_trigger_enable/disable clear pending and can miss interrupt + // when disabled if (enabled) { - nrfx_gpiote_trigger_enable(MAX3241E_INTR_PIN, true); + NVIC_EnableIRQ(GPIOTE_IRQn); } else { - nrfx_gpiote_trigger_disable(MAX3241E_INTR_PIN); + NVIC_DisableIRQ(GPIOTE_IRQn); } } @@ -266,6 +268,7 @@ void board_init(void) { in_config.pull = NRF_GPIO_PIN_PULLUP; nrfx_gpiote_in_init(MAX3241E_INTR_PIN, &in_config, max3421e_int_handler); + nrfx_gpiote_trigger_enable(MAX3241E_INTR_PIN, true); #endif } diff --git a/src/host/usbh.c b/src/host/usbh.c index e60e680c2..e332f35cc 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -753,29 +753,33 @@ bool tuh_edpt_abort_xfer(uint8_t daddr, uint8_t ep_addr) { // USBH API For Class Driver //--------------------------------------------------------------------+ -uint8_t usbh_get_rhport(uint8_t dev_addr) -{ - usbh_device_t* dev = get_device(dev_addr); +uint8_t usbh_get_rhport(uint8_t dev_addr) { + usbh_device_t *dev = get_device(dev_addr); return dev ? dev->rhport : _dev0.rhport; } -uint8_t* usbh_get_enum_buf(void) -{ +uint8_t *usbh_get_enum_buf(void) { return _usbh_ctrl_buf; } -void usbh_int_set(bool enabled) -{ +void usbh_int_set(bool enabled) { // TODO all host controller if multiple are used since they shared the same event queue - if (enabled) - { + if (enabled) { hcd_int_enable(_usbh_controller); - }else - { + } else { hcd_int_disable(_usbh_controller); } } +void usbh_defer_func(osal_task_func_t func, void *param, bool in_isr) { + hcd_event_t event = { 0 }; + event.event_id = USBH_EVENT_FUNC_CALL; + event.func_call.func = func; + event.func_call.param = param; + + osal_queue_send(_usbh_q, &event, in_isr); +} + //--------------------------------------------------------------------+ // Endpoint API //--------------------------------------------------------------------+ diff --git a/src/host/usbh_pvt.h b/src/host/usbh_pvt.h index 0b58a91bc..2b61a77db 100644 --- a/src/host/usbh_pvt.h +++ b/src/host/usbh_pvt.h @@ -24,8 +24,8 @@ * This file is part of the TinyUSB stack. */ -#ifndef _TUSB_USBH_CLASSDRIVER_H_ -#define _TUSB_USBH_CLASSDRIVER_H_ +#ifndef _TUSB_USBH_PVT_H_ +#define _TUSB_USBH_PVT_H_ #include "osal/osal.h" #include "common/tusb_fifo.h" @@ -76,6 +76,8 @@ uint8_t* usbh_get_enum_buf(void); void usbh_int_set(bool enabled); +void usbh_defer_func(osal_task_func_t func, void *param, bool in_isr); + //--------------------------------------------------------------------+ // USBH Endpoint API //--------------------------------------------------------------------+ @@ -85,12 +87,10 @@ bool usbh_edpt_xfer_with_callback(uint8_t dev_addr, uint8_t ep_addr, uint8_t * b tuh_xfer_cb_t complete_cb, uintptr_t user_data); TU_ATTR_ALWAYS_INLINE -static inline bool usbh_edpt_xfer(uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes) -{ +static inline bool usbh_edpt_xfer(uint8_t dev_addr, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes) { return usbh_edpt_xfer_with_callback(dev_addr, ep_addr, buffer, total_bytes, NULL, 0); } - // Claim an endpoint before submitting a transfer. // If caller does not make any transfer, it must release endpoint for others. bool usbh_edpt_claim(uint8_t dev_addr, uint8_t ep_addr); diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index c61389cb9..95cf5516e 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -194,7 +194,6 @@ typedef struct { uint8_t hxfr; atomic_flag busy; // busy transferring - volatile uint8_t intr_disable_count; volatile uint16_t frame_count; max3421_ep_t ep[CFG_TUH_MAX3421_ENDPOINT_TOTAL]; // [0] is reserved for addr0 @@ -241,14 +240,6 @@ static void max3421_spi_unlock(uint8_t rhport, bool in_isr) { if (!in_isr) { tuh_max3421e_int_api(rhport, true); (void) osal_mutex_unlock(_hcd_data.spi_mutex); - - // when re-enable interrupt, we may miss INTR edge (usually via GPIO detection interrupt). - // It would be ok if we are operating since SOF will re-trigger interrupt. - // However, for CONDET_IRQ i.e host not operating therefore we need to manually handle it here. - if (_hcd_data.hirq & HIRQ_CONDET_IRQ) { - handle_connect_irq(rhport, false); - hirq_write(rhport, HIRQ_CONDET_IRQ, false); - } } } @@ -470,28 +461,13 @@ bool hcd_init(uint8_t rhport) { // Enable USB interrupt // Not actually enable GPIO interrupt, just set variable to prevent handler to process void hcd_int_enable (uint8_t rhport) { -// tuh_max3421e_int_api(rhport, true); - - (void) rhport; - if (_hcd_data.intr_disable_count) { - _hcd_data.intr_disable_count--; - } - - // when re-enable interrupt, we may miss INTR edge (usually via GPIO detection interrupt). - // It would be ok if we are operating since SOF will re-trigger interrupt. - // However, for CONDET_IRQ i.e host not operating therefore we need to manually handle it here. -// if (_hcd_data.hirq & HIRQ_CONDET_IRQ) { -// handle_connect_irq(rhport, false); -// hirq_write(rhport, HIRQ_CONDET_IRQ, false); -// } + tuh_max3421e_int_api(rhport, true); } // Disable USB interrupt // Not actually disable GPIO interrupt, just set variable to prevent handler to process void hcd_int_disable(uint8_t rhport) { - //tuh_max3421e_int_api(rhport, false); - (void) rhport; - _hcd_data.intr_disable_count++; + tuh_max3421e_int_api(rhport, false); } // Get frame number (1ms) @@ -896,14 +872,6 @@ void hcd_int_handler(uint8_t rhport) { _hcd_data.frame_count++; } - // interrupt is disabled by usbh task: only ack FRAME IRQ and skip the rest - if (_hcd_data.intr_disable_count) { - if (hirq & HIRQ_FRAME_IRQ) { - hirq_write(rhport, HIRQ_FRAME_IRQ, true); - } - return; - } - if (hirq & HIRQ_CONDET_IRQ) { handle_connect_irq(rhport, true); } -- cgit v1.3.1 From 7ce4cfa638a86bfabd7ce8147ea5468d69c1af21 Mon Sep 17 00:00:00 2001 From: maidnl Date: Fri, 8 Sep 2023 10:12:03 +0200 Subject: renesas: added wait function for IN transaction This fixes a problem found on MSD class where data read from from disks were sometimes partially overwritten by the status MSD message ("USBS..."). The function introduced wait for the hw fifo pipe to be empty, that prevent that new writing in the fife overwrite data which are not yet be transmitted by hw. --- src/portable/renesas/rusb2/dcd_rusb2.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 3ec1b70b5..68ef5890f 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -266,6 +266,13 @@ static void pipe_read_packet_ff(rusb2_reg_t * rusb, tu_fifo_t *f, volatile void tu_fifo_advance_write_pointer(f, count); } + +static void wait_pipe_fifo_empty(rusb2_reg_t* rusb, uint8_t num) { + TU_ASSERT(num); + while( (rusb->PIPE_CTR[num-1] & RUSB2_PIPE_CTR_INBUFM_Msk) > 0 ) {} +} + + //--------------------------------------------------------------------+ // Pipe Transfer //--------------------------------------------------------------------+ @@ -339,6 +346,7 @@ static bool pipe_xfer_in(rusb2_reg_t* rusb, unsigned num) const unsigned rem = pipe->remaining; if (!rem) { + wait_pipe_fifo_empty(rusb, num); pipe->buf = NULL; return true; } -- cgit v1.3.1 From 228acbeac2642534753beffd866db2a7eab45e31 Mon Sep 17 00:00:00 2001 From: maidnl Date: Fri, 8 Sep 2023 15:48:05 +0200 Subject: wait_pipe_fifo_empty() now returns bool (as expected using TU_ASSERT macro) --- src/portable/renesas/rusb2/dcd_rusb2.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/renesas/rusb2/dcd_rusb2.c b/src/portable/renesas/rusb2/dcd_rusb2.c index 68ef5890f..24edc30e7 100644 --- a/src/portable/renesas/rusb2/dcd_rusb2.c +++ b/src/portable/renesas/rusb2/dcd_rusb2.c @@ -267,9 +267,10 @@ static void pipe_read_packet_ff(rusb2_reg_t * rusb, tu_fifo_t *f, volatile void } -static void wait_pipe_fifo_empty(rusb2_reg_t* rusb, uint8_t num) { +static bool wait_pipe_fifo_empty(rusb2_reg_t* rusb, uint8_t num) { TU_ASSERT(num); while( (rusb->PIPE_CTR[num-1] & RUSB2_PIPE_CTR_INBUFM_Msk) > 0 ) {} + return true; } -- cgit v1.3.1 From c074488f75522c7c29dc7853aa2d8597b4858f89 Mon Sep 17 00:00:00 2001 From: hathach Date: Sat, 9 Sep 2023 12:20:16 +0700 Subject: minor rename --- hw/bsp/nrf/boards/feather_nrf52840_express/board.h | 10 +- hw/bsp/nrf/boards/pca10056/board.h | 10 +- hw/bsp/nrf/boards/pca10095/board.h | 10 +- hw/bsp/nrf/family.c | 22 +-- hw/bsp/samd51/boards/metro_m4_express/board.h | 12 +- hw/bsp/samd51/family.c | 183 +++++++++++---------- src/portable/analog/max3421/hcd_max3421.c | 14 +- 7 files changed, 131 insertions(+), 130 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/nrf/boards/feather_nrf52840_express/board.h b/hw/bsp/nrf/boards/feather_nrf52840_express/board.h index e6e7590ac..76100a14a 100644 --- a/hw/bsp/nrf/boards/feather_nrf52840_express/board.h +++ b/hw/bsp/nrf/boards/feather_nrf52840_express/board.h @@ -46,11 +46,11 @@ #define UART_TX_PIN 25 // SPI for USB host shield -#define MAX3421E_SCK_PIN 14 -#define MAX3421E_MOSI_PIN 13 -#define MAX3421E_MISO_PIN 15 -#define MAX3421E_CS_PIN 27 -#define MAX3241E_INTR_PIN 26 +#define MAX3421_SCK_PIN 14 +#define MAX3421_MOSI_PIN 13 +#define MAX3421_MISO_PIN 15 +#define MAX3421_CS_PIN 27 +#define MAX3421_INTR_PIN 26 #ifdef __cplusplus } diff --git a/hw/bsp/nrf/boards/pca10056/board.h b/hw/bsp/nrf/boards/pca10056/board.h index 16d31addb..9459e7911 100644 --- a/hw/bsp/nrf/boards/pca10056/board.h +++ b/hw/bsp/nrf/boards/pca10056/board.h @@ -46,11 +46,11 @@ #define UART_TX_PIN 6 // SPI for USB host shield -#define MAX3421E_SCK_PIN _PINNUM(1, 15) -#define MAX3421E_MOSI_PIN _PINNUM(1, 13) -#define MAX3421E_MISO_PIN _PINNUM(1, 14) -#define MAX3421E_CS_PIN _PINNUM(1, 12) -#define MAX3241E_INTR_PIN _PINNUM(1, 11) +#define MAX3421_SCK_PIN _PINNUM(1, 15) +#define MAX3421_MOSI_PIN _PINNUM(1, 13) +#define MAX3421_MISO_PIN _PINNUM(1, 14) +#define MAX3421_CS_PIN _PINNUM(1, 12) +#define MAX3421_INTR_PIN _PINNUM(1, 11) #ifdef __cplusplus } diff --git a/hw/bsp/nrf/boards/pca10095/board.h b/hw/bsp/nrf/boards/pca10095/board.h index b9d3a19dc..ad3379bf6 100644 --- a/hw/bsp/nrf/boards/pca10095/board.h +++ b/hw/bsp/nrf/boards/pca10095/board.h @@ -46,11 +46,11 @@ #define UART_TX_PIN 33 // SPI for USB host shield -#define MAX3421E_SCK_PIN _PINNUM(1, 15) -#define MAX3421E_MOSI_PIN _PINNUM(1, 13) -#define MAX3421E_MISO_PIN _PINNUM(1, 14) -#define MAX3421E_CS_PIN _PINNUM(1, 12) -#define MAX3241E_INTR_PIN _PINNUM(1, 11) +#define MAX3421_SCK_PIN _PINNUM(1, 15) +#define MAX3421_MOSI_PIN _PINNUM(1, 13) +#define MAX3421_MISO_PIN _PINNUM(1, 14) +#define MAX3421_CS_PIN _PINNUM(1, 12) +#define MAX3421_INTR_PIN _PINNUM(1, 11) #ifdef __cplusplus } diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 47c765a96..6fcfd9476 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -97,8 +97,8 @@ TU_ATTR_UNUSED static void power_event_handler(nrfx_power_usb_evt_t event) { #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(1); -void max3421e_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { - if (!(pin == MAX3241E_INTR_PIN && action == NRF_GPIOTE_POLARITY_HITOLO)) return; +void max3421_int_handler(nrfx_gpiote_pin_t pin, nrf_gpiote_polarity_t action) { + if (!(pin == MAX3421_INTR_PIN && action == NRF_GPIOTE_POLARITY_HITOLO)) return; tuh_int_handler(1); } @@ -207,14 +207,14 @@ void board_init(void) { #endif // manually manage CS - nrf_gpio_cfg_output(MAX3421E_CS_PIN); - nrf_gpio_pin_write(MAX3421E_CS_PIN, 1); + nrf_gpio_cfg_output(MAX3421_CS_PIN); + nrf_gpio_pin_write(MAX3421_CS_PIN, 1); // USB host using max3421e usb controller via SPI nrfx_spim_config_t cfg = { - .sck_pin = MAX3421E_SCK_PIN, - .mosi_pin = MAX3421E_MOSI_PIN, - .miso_pin = MAX3421E_MISO_PIN, + .sck_pin = MAX3421_SCK_PIN, + .mosi_pin = MAX3421_MOSI_PIN, + .miso_pin = MAX3421_MISO_PIN, .ss_pin = NRFX_SPIM_PIN_NOT_USED, .ss_active_high = false, .irq_priority = 3, @@ -233,8 +233,8 @@ void board_init(void) { nrfx_gpiote_in_config_t in_config = NRFX_GPIOTE_CONFIG_IN_SENSE_HITOLO(true); in_config.pull = NRF_GPIO_PIN_PULLUP; - nrfx_gpiote_in_init(MAX3241E_INTR_PIN, &in_config, max3421e_int_handler); - nrfx_gpiote_trigger_enable(MAX3241E_INTR_PIN, true); + nrfx_gpiote_in_init(MAX3421_INTR_PIN, &in_config, max3421_int_handler); + nrfx_gpiote_trigger_enable(MAX3421_INTR_PIN, true); #endif } @@ -317,7 +317,7 @@ void nrf_error_cb(uint32_t id, uint32_t pc, uint32_t info) { //--------------------------------------------------------------------+ #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 -void tuh_max3421e_int_api(uint8_t rhport, bool enabled) { +void tuh_max3421_int_api(uint8_t rhport, bool enabled) { (void) rhport; // use NVIC_Enable/Disable instead since nrfx_gpiote_trigger_enable/disable clear pending and can miss interrupt @@ -331,7 +331,7 @@ void tuh_max3421e_int_api(uint8_t rhport, bool enabled) { void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { (void) rhport; - nrf_gpio_pin_write(MAX3421E_CS_PIN, active ? 0 : 1); + nrf_gpio_pin_write(MAX3421_CS_PIN, active ? 0 : 1); } bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_len, uint8_t *rx_buf, size_t rx_len) { diff --git a/hw/bsp/samd51/boards/metro_m4_express/board.h b/hw/bsp/samd51/boards/metro_m4_express/board.h index 3441d03e9..fe2a867a4 100644 --- a/hw/bsp/samd51/boards/metro_m4_express/board.h +++ b/hw/bsp/samd51/boards/metro_m4_express/board.h @@ -44,12 +44,12 @@ #define UART_RX_PIN 22 // SPI for USB host shield -#define MAX3421E_SERCOM SERCOM2 -#define MAX3421E_SCK_PIN 13 -#define MAX3421E_MOSI_PIN 12 -#define MAX3421E_MISO_PIN 14 -#define MAX3421E_CS_PIN 18 // D10 -#define MAX3241E_INTR_PIN 20 // D9 +#define MAX3421_SERCOM 2 // SERCOM2 +#define MAX3421_SCK_PIN 13 +#define MAX3421_MOSI_PIN 12 +#define MAX3421_MISO_PIN 14 +#define MAX3421_CS_PIN 18 // D10 +#define MAX3421_INTR_PIN 20 // D9 #ifdef __cplusplus diff --git a/hw/bsp/samd51/family.c b/hw/bsp/samd51/family.c index 51cfd19ba..34dd93cef 100644 --- a/hw/bsp/samd51/family.c +++ b/hw/bsp/samd51/family.c @@ -73,58 +73,14 @@ void USB_3_Handler(void) { } //--------------------------------------------------------------------+ -// +// Implementation //--------------------------------------------------------------------+ #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 -void max3421_init(void) -{ - //------------- SPI Init -------------// - - // Enable the APB clock for SERCOM2 - MCLK->APBBMASK.reg |= MCLK_APBBMASK_SERCOM2; - - // Configure GCLK for SERCOM2, initClockNVIC() - GCLK->PCHCTRL[SERCOM2_GCLK_ID_CORE].reg = GCLK_PCHCTRL_GEN_GCLK0_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); - GCLK->PCHCTRL[SERCOM2_GCLK_ID_SLOW].reg = GCLK_PCHCTRL_GEN_GCLK3_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); +static void max3421_init(void); - // Disable the SPI module - SERCOM2->SPI.CTRLA.bit.ENABLE = 0; - - // Reset the SPI module - SERCOM2->SPI.CTRLA.bit.SWRST = 1; - while (SERCOM2->SPI.SYNCBUSY.bit.SWRST); +//#define - // Set up SPI in master mode, MSB first, SPI mode 0 - uint8_t const mosi_pad = 0; - uint8_t const miso_pad = 2; - SERCOM2->SPI.CTRLA.reg = SERCOM_SPI_CTRLA_MODE(3) | SERCOM_SPI_CTRLA_DOPO(mosi_pad) | SERCOM_SPI_CTRLA_DIPO(miso_pad); - - SERCOM2->SPI.CTRLB.reg = SERCOM_SPI_CTRLB_CHSIZE(0) | SERCOM_SPI_CTRLB_RXEN; - while( SERCOM2->SPI.SYNCBUSY.bit.CTRLB == 1 ); - - // Set the baud rate - uint32_t baudrate = 4000000u; - SERCOM2->SPI.BAUD.reg = (uint8_t)(SystemCoreClock / (2 * baudrate) - 1); // Replace 1000000 with your desired baud rate - - // Configure PA12 as MOSI (PAD0), PA13 as SCK (PAD1), PA14 as MISO (PAD2) - // 2 function C: PIO_SERCOM - gpio_set_pin_direction(MAX3421E_SCK_PIN, GPIO_DIRECTION_OUT); - gpio_set_pin_pull_mode(MAX3421E_SCK_PIN, GPIO_PULL_OFF); - gpio_set_pin_function(MAX3421E_SCK_PIN, 2); - - gpio_set_pin_direction(MAX3421E_MOSI_PIN, GPIO_DIRECTION_OUT); - gpio_set_pin_pull_mode(MAX3421E_MOSI_PIN, GPIO_PULL_OFF); - gpio_set_pin_function(MAX3421E_MOSI_PIN, 2); - - gpio_set_pin_direction(MAX3421E_MISO_PIN, GPIO_DIRECTION_IN); - gpio_set_pin_pull_mode(MAX3421E_MISO_PIN, GPIO_PULL_OFF); - gpio_set_pin_function(MAX3421E_MISO_PIN, 2); - - // Enable the SPI module - SERCOM2->SPI.CTRLA.bit.ENABLE = 1; - while (SERCOM2->SPI.SYNCBUSY.bit.ENABLE); -} #endif void board_init(void) { @@ -180,46 +136,7 @@ void board_init(void) { gpio_set_pin_function(PIN_PA25, PINMUX_PA25H_USB_DP); #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 - // CS pin - gpio_set_pin_direction(MAX3421E_CS_PIN, GPIO_DIRECTION_OUT); - gpio_set_pin_level(MAX3421E_CS_PIN, 1); - - // SPI max3421_init(); - - // INT pin with external interrupt - gpio_set_pin_direction(MAX3241E_INTR_PIN, GPIO_DIRECTION_IN); - gpio_set_pin_pull_mode(MAX3241E_INTR_PIN, GPIO_PULL_UP); - - // Enable the APB clock for EIC (External Interrupt Controller) - MCLK->APBAMASK.reg |= MCLK_APBAMASK_EIC; - - // Configure GCLK for EIC - GCLK->PCHCTRL[EIC_GCLK_ID].reg = GCLK_PCHCTRL_GEN_GCLK0_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); - - // Configure PA20 as an input - PORT->Group[0].DIRCLR.reg = PORT_PA20; - PORT->Group[0].PINCFG[20].reg = PORT_PINCFG_INEN | PORT_PINCFG_PULLEN; - PORT->Group[0].OUTSET.reg = PORT_PA20; // Enable pull-up - - // Configure PA20 to use EIC - PORT->Group[0].PMUX[10].bit.PMUXE = MUX_PA20A_EIC_EXTINT4; - PORT->Group[0].PINCFG[20].bit.PMUXEN = 1; - - // Disable EIC - EIC->CTRLA.bit.ENABLE = 0; - while (EIC->SYNCBUSY.bit.ENABLE); - - // Configure EXTINT4 (PA20) to trigger on falling edge - EIC->CONFIG[0].reg |= EIC_CONFIG_SENSE4_FALL; - - // Enable EXTINT4 - EIC->INTENSET.reg = EIC_INTENSET_EXTINT(1 << 4); - - // Enable EIC - EIC->CTRLA.bit.ENABLE = 1; - while (EIC->SYNCBUSY.bit.ENABLE); - #endif } @@ -264,8 +181,91 @@ uint32_t board_millis(void) { //--------------------------------------------------------------------+ #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 -void EIC_4_Handler(void) -{ +static void max3421_init(void) { + // CS pin + gpio_set_pin_direction(MAX3421_CS_PIN, GPIO_DIRECTION_OUT); + gpio_set_pin_level(MAX3421_CS_PIN, 1); + + //------------- SPI Init -------------// + + // Enable the APB clock for SERCOM2 + MCLK->APBBMASK.reg |= MCLK_APBBMASK_SERCOM2; + + // Configure GCLK for SERCOM2, initClockNVIC() + GCLK->PCHCTRL[SERCOM2_GCLK_ID_CORE].reg = GCLK_PCHCTRL_GEN_GCLK0_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); + GCLK->PCHCTRL[SERCOM2_GCLK_ID_SLOW].reg = GCLK_PCHCTRL_GEN_GCLK3_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); + + // Disable the SPI module + SERCOM2->SPI.CTRLA.bit.ENABLE = 0; + + // Reset the SPI module + SERCOM2->SPI.CTRLA.bit.SWRST = 1; + while (SERCOM2->SPI.SYNCBUSY.bit.SWRST); + + // Set up SPI in master mode, MSB first, SPI mode 0 + uint8_t const mosi_pad = 0; + uint8_t const miso_pad = 2; + SERCOM2->SPI.CTRLA.reg = SERCOM_SPI_CTRLA_MODE(3) | SERCOM_SPI_CTRLA_DOPO(mosi_pad) | SERCOM_SPI_CTRLA_DIPO(miso_pad); + + SERCOM2->SPI.CTRLB.reg = SERCOM_SPI_CTRLB_CHSIZE(0) | SERCOM_SPI_CTRLB_RXEN; + while (SERCOM2->SPI.SYNCBUSY.bit.CTRLB == 1); + + // Set the baud rate + uint32_t baudrate = 4000000u; + SERCOM2->SPI.BAUD.reg = (uint8_t) (SystemCoreClock / (2 * baudrate) - + 1); // Replace 1000000 with your desired baud rate + + // Configure PA12 as MOSI (PAD0), PA13 as SCK (PAD1), PA14 as MISO (PAD2) + // 2 function C: PIO_SERCOM + gpio_set_pin_direction(MAX3421_SCK_PIN, GPIO_DIRECTION_OUT); + gpio_set_pin_pull_mode(MAX3421_SCK_PIN, GPIO_PULL_OFF); + gpio_set_pin_function(MAX3421_SCK_PIN, 2); + + gpio_set_pin_direction(MAX3421_MOSI_PIN, GPIO_DIRECTION_OUT); + gpio_set_pin_pull_mode(MAX3421_MOSI_PIN, GPIO_PULL_OFF); + gpio_set_pin_function(MAX3421_MOSI_PIN, 2); + + gpio_set_pin_direction(MAX3421_MISO_PIN, GPIO_DIRECTION_IN); + gpio_set_pin_pull_mode(MAX3421_MISO_PIN, GPIO_PULL_OFF); + gpio_set_pin_function(MAX3421_MISO_PIN, 2); + + // Enable the SPI module + SERCOM2->SPI.CTRLA.bit.ENABLE = 1; + while (SERCOM2->SPI.SYNCBUSY.bit.ENABLE); + + //------------- External Interrupt -------------// + + // INT pin with external interrupt + gpio_set_pin_direction(MAX3421_INTR_PIN, GPIO_DIRECTION_IN); + gpio_set_pin_pull_mode(MAX3421_INTR_PIN, GPIO_PULL_UP); + + // Enable the APB clock for EIC (External Interrupt Controller) + MCLK->APBAMASK.reg |= MCLK_APBAMASK_EIC; + + // Configure GCLK for EIC + GCLK->PCHCTRL[EIC_GCLK_ID].reg = GCLK_PCHCTRL_GEN_GCLK0_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); + + // Configure PA20 as an input with function A (external interrupt) + gpio_set_pin_direction(MAX3421_INTR_PIN, GPIO_DIRECTION_IN); + gpio_set_pin_pull_mode(MAX3421_INTR_PIN, GPIO_PULL_UP); + gpio_set_pin_function(MAX3421_INTR_PIN, 0); + + // Disable EIC + EIC->CTRLA.bit.ENABLE = 0; + while (EIC->SYNCBUSY.bit.ENABLE); + + // Configure EXTINT4 (PA20) to trigger on falling edge + EIC->CONFIG[0].reg |= EIC_CONFIG_SENSE4_FALL; + + // Enable EXTINT4 + EIC->INTENSET.reg = EIC_INTENSET_EXTINT(1 << 4); + + // Enable EIC + EIC->CTRLA.bit.ENABLE = 1; + while (EIC->SYNCBUSY.bit.ENABLE); +} + +void EIC_4_Handler(void) { // Clear the interrupt flag EIC->INTFLAG.reg = EIC_INTFLAG_EXTINT(1 << 4); @@ -273,7 +273,7 @@ void EIC_4_Handler(void) tuh_int_handler(1); } -void tuh_max3421e_int_api(uint8_t rhport, bool enabled) { +void tuh_max3421_int_api(uint8_t rhport, bool enabled) { (void) rhport; if (enabled) { @@ -285,7 +285,7 @@ void tuh_max3421e_int_api(uint8_t rhport, bool enabled) { void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { (void) rhport; - gpio_set_pin_level(MAX3421E_CS_PIN, active ? 0 : 1); + gpio_set_pin_level(MAX3421_CS_PIN, active ? 0 : 1); } bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_len, uint8_t *rx_buf, size_t rx_len) { @@ -299,7 +299,7 @@ bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_l // Write data to be transmitted uint8_t data = 0x00; if (count < tx_len) { - data = tx_buf[count]; + data = tx_buf[count]; } SERCOM2->SPI.DATA.reg = (uint32_t) data; @@ -322,6 +322,7 @@ bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_l return true; } + #endif #endif diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 95cf5516e..238b518a0 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -212,7 +212,7 @@ static max3421_data_t _hcd_data; void tuh_max3421_spi_cs_api(uint8_t rhport, bool active); bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len); -void tuh_max3421e_int_api(uint8_t rhport, bool enabled); +void tuh_max3421_int_api(uint8_t rhport, bool enabled); static void handle_connect_irq(uint8_t rhport, bool in_isr); static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr); @@ -225,7 +225,7 @@ static void max3421_spi_lock(uint8_t rhport, bool in_isr) { // disable interrupt and mutex lock (for pre-emptive RTOS) if not in_isr if (!in_isr) { (void) osal_mutex_lock(_hcd_data.spi_mutex, OSAL_TIMEOUT_WAIT_FOREVER); - tuh_max3421e_int_api(rhport, false); + tuh_max3421_int_api(rhport, false); } // assert CS @@ -238,7 +238,7 @@ static void max3421_spi_unlock(uint8_t rhport, bool in_isr) { // mutex unlock and re-enable interrupt if (!in_isr) { - tuh_max3421e_int_api(rhport, true); + tuh_max3421_int_api(rhport, true); (void) osal_mutex_unlock(_hcd_data.spi_mutex); } } @@ -411,7 +411,7 @@ bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { bool hcd_init(uint8_t rhport) { (void) rhport; - tuh_max3421e_int_api(rhport, false); + tuh_max3421_int_api(rhport, false); tuh_max3421_spi_cs_api(rhport, false); TU_LOG2_INT(sizeof(max3421_ep_t)); @@ -450,7 +450,7 @@ bool hcd_init(uint8_t rhport) { // Enable IRQ hien_write(rhport, DEFAULT_HIEN, false); - tuh_max3421e_int_api(rhport, true); + tuh_max3421_int_api(rhport, true); // Enable Interrupt pin reg_write(rhport, CPUCTL_ADDR, CPUCTL_IE, false); @@ -461,13 +461,13 @@ bool hcd_init(uint8_t rhport) { // Enable USB interrupt // Not actually enable GPIO interrupt, just set variable to prevent handler to process void hcd_int_enable (uint8_t rhport) { - tuh_max3421e_int_api(rhport, true); + tuh_max3421_int_api(rhport, true); } // Disable USB interrupt // Not actually disable GPIO interrupt, just set variable to prevent handler to process void hcd_int_disable(uint8_t rhport) { - tuh_max3421e_int_api(rhport, false); + tuh_max3421_int_api(rhport, false); } // Get frame number (1ms) -- cgit v1.3.1 From 81cd9951080181234f20d81c831ca0595d499577 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 18 Sep 2023 22:15:31 +0700 Subject: add default CFG_TUH_MAX3421 = 0, default spi speed for samd21/samd51 to 12Mhz --- hw/bsp/samd21/family.c | 3 ++- hw/bsp/samd51/family.c | 11 +++++++++-- src/portable/analog/max3421/hcd_max3421.c | 2 +- src/tusb_option.h | 22 +++++++++++++--------- 4 files changed, 25 insertions(+), 13 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/samd21/family.c b/hw/bsp/samd21/family.c index cfe66b8dc..395155548 100644 --- a/hw/bsp/samd21/family.c +++ b/hw/bsp/samd21/family.c @@ -269,7 +269,8 @@ uint32_t board_millis(void) { static void max3421_init(void) { //------------- SPI Init -------------// - uint32_t const baudrate = 4000000u; + // MAX3421E max SPI clock is 26MHz however SAMD can only work reliably at 12 Mhz + uint32_t const baudrate = 12000000u; // Enable the APB clock for SERCOM PM->APBCMASK.reg |= 1u << (PM_APBCMASK_SERCOM0_Pos + MAX3421_SERCOM_ID); diff --git a/hw/bsp/samd51/family.c b/hw/bsp/samd51/family.c index 2cf00c7af..c1b914a02 100644 --- a/hw/bsp/samd51/family.c +++ b/hw/bsp/samd51/family.c @@ -183,7 +183,9 @@ uint32_t board_millis(void) { static void max3421_init(void) { //------------- SPI Init -------------// - uint32_t const baudrate = 4000000u; + + // MAX3421E max SPI clock is 26MHz however SAMD can only work reliably at 12 Mhz + uint32_t const baudrate = 12000000u; struct { volatile uint32_t *mck_apb; @@ -229,7 +231,12 @@ static void max3421_init(void) { while (sercom->SPI.SYNCBUSY.bit.CTRLB == 1); // Set the baud rate - sercom->SPI.BAUD.reg = (uint8_t) (SystemCoreClock / (2 * baudrate) - 1); + uint8_t baud_reg = (uint8_t) (SystemCoreClock / (2 * baudrate)); + if (baud_reg) { + baud_reg--; + } + + sercom->SPI.BAUD.reg = baud_reg; // Configure PA12 as MOSI (PAD0), PA13 as SCK (PAD1), PA14 as MISO (PAD2), function C (sercom) gpio_set_pin_direction(MAX3421_SCK_PIN, GPIO_DIRECTION_OUT); diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 238b518a0..f3f76fd58 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -263,7 +263,7 @@ static void fifo_read(uint8_t rhport, uint8_t * buffer, uint16_t len, bool in_is max3421_spi_lock(rhport, in_isr); - tuh_max3421_spi_xfer_api(rhport, ®, 1, &hirq, 0); + tuh_max3421_spi_xfer_api(rhport, ®, 1, &hirq, 1); _hcd_data.hirq = hirq; tuh_max3421_spi_xfer_api(rhport, NULL, 0, buffer, len); diff --git a/src/tusb_option.h b/src/tusb_option.h index c72117850..a41f5a07e 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -424,11 +424,11 @@ //------------- CLASS -------------// #ifndef CFG_TUH_HUB -#define CFG_TUH_HUB 0 + #define CFG_TUH_HUB 0 #endif #ifndef CFG_TUH_CDC -#define CFG_TUH_CDC 0 + #define CFG_TUH_CDC 0 #endif #ifndef CFG_TUH_CDC_FTDI @@ -442,34 +442,38 @@ #endif #ifndef CFG_TUH_HID -#define CFG_TUH_HID 0 + #define CFG_TUH_HID 0 #endif #ifndef CFG_TUH_MIDI -#define CFG_TUH_MIDI 0 + #define CFG_TUH_MIDI 0 #endif #ifndef CFG_TUH_MSC -#define CFG_TUH_MSC 0 + #define CFG_TUH_MSC 0 #endif #ifndef CFG_TUH_VENDOR -#define CFG_TUH_VENDOR 0 + #define CFG_TUH_VENDOR 0 #endif #ifndef CFG_TUH_API_EDPT_XFER -#define CFG_TUH_API_EDPT_XFER 0 + #define CFG_TUH_API_EDPT_XFER 0 #endif // Enable PIO-USB software host controller #ifndef CFG_TUH_RPI_PIO_USB -#define CFG_TUH_RPI_PIO_USB 0 + #define CFG_TUH_RPI_PIO_USB 0 #endif #ifndef CFG_TUD_RPI_PIO_USB -#define CFG_TUD_RPI_PIO_USB 0 + #define CFG_TUD_RPI_PIO_USB 0 #endif +// MAX3421 Host controller option +#ifndef CFG_TUH_MAX3421 + #define CFG_TUH_MAX3421 0 +#endif //--------------------------------------------------------------------+ // TypeC Options (Default) -- cgit v1.3.1 From a7c136c03f0c4a057f8b49c10ed9cddcecf52879 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 25 Sep 2023 16:53:11 +0700 Subject: adding host/cdc_msc_hid_freertos example --- .idea/cmake.xml | 19 +-- examples/device/cdc_msc_freertos/Makefile | 2 +- examples/device/cdc_msc_freertos/src/main.c | 70 ++++----- examples/host/bare_api/CMakeLists.txt | 5 + examples/host/cdc_msc_hid/CMakeLists.txt | 5 + examples/host/cdc_msc_hid_freertos/CMakeLists.txt | 36 +++++ .../host/cdc_msc_hid_freertos/src/CMakeLists.txt | 4 + examples/host/cdc_msc_hid_freertos/src/main.c | 170 +++++++++++++++++++++ .../host/cdc_msc_hid_freertos/src/tusb_config.h | 133 ++++++++++++++++ examples/host/hid_controller/CMakeLists.txt | 5 + examples/host/msc_file_explorer/CMakeLists.txt | 5 + examples/make.mk | 3 - .../boards/adafruit_metro_esp32s2/board.h | 8 + hw/bsp/espressif/boards/espressif_kaluga_1/board.h | 8 + .../boards/espressif_s2_devkitc/board.cmake | 2 + .../espressif/boards/espressif_s2_devkitc/board.h | 45 ++++++ hw/bsp/espressif/boards/family.c | 130 +++++++++++++--- .../components/tinyusb_src/CMakeLists.txt | 79 ++++++---- src/host/usbh.c | 2 +- src/portable/analog/max3421/hcd_max3421.c | 2 +- 20 files changed, 622 insertions(+), 111 deletions(-) create mode 100644 examples/host/cdc_msc_hid_freertos/CMakeLists.txt create mode 100644 examples/host/cdc_msc_hid_freertos/src/CMakeLists.txt create mode 100644 examples/host/cdc_msc_hid_freertos/src/main.c create mode 100644 examples/host/cdc_msc_hid_freertos/src/tusb_config.h create mode 100644 hw/bsp/espressif/boards/espressif_s2_devkitc/board.cmake create mode 100644 hw/bsp/espressif/boards/espressif_s2_devkitc/board.h (limited to 'src/portable') diff --git a/.idea/cmake.xml b/.idea/cmake.xml index 89ec1066c..747f0fb58 100644 --- a/.idea/cmake.xml +++ b/.idea/cmake.xml @@ -2,23 +2,24 @@ - + - - - - + + + + + + + + - - - @@ -53,7 +54,7 @@ - + diff --git a/examples/device/cdc_msc_freertos/Makefile b/examples/device/cdc_msc_freertos/Makefile index 0bee668b7..3ac62a79c 100644 --- a/examples/device/cdc_msc_freertos/Makefile +++ b/examples/device/cdc_msc_freertos/Makefile @@ -10,7 +10,7 @@ INC += \ src/FreeRTOSConfig \ $(TOP)/hw \ $(TOP)/$(FREERTOS_SRC)/include \ - $(TOP)/$(FREERTOS_PORTABLE_SRC) + $(TOP)/$(FREERTOS_PORTABLE_SRC) \ # Example source EXAMPLE_SOURCE = \ diff --git a/examples/device/cdc_msc_freertos/src/main.c b/examples/device/cdc_msc_freertos/src/main.c index 0b115a595..1dadc4513 100644 --- a/examples/device/cdc_msc_freertos/src/main.c +++ b/examples/device/cdc_msc_freertos/src/main.c @@ -41,6 +41,7 @@ #define USBD_STACK_SIZE 4096 #else + #include "FreeRTOS.h" #include "semphr.h" #include "queue.h" @@ -54,7 +55,7 @@ #define CDC_STACK_SZIE configMINIMAL_STACK_SIZE //--------------------------------------------------------------------+ -// MACRO CONSTANT TYPEDEF PROTYPES +// MACRO CONSTANT TYPEDEF PROTOTYPES //--------------------------------------------------------------------+ /* Blink pattern @@ -62,7 +63,7 @@ * - 1000 ms : device mounted * - 2500 ms : device is suspended */ -enum { +enum { BLINK_NOT_MOUNTED = 250, BLINK_MOUNTED = 1000, BLINK_SUSPENDED = 2500, @@ -81,16 +82,15 @@ StaticTask_t cdc_taskdef; TimerHandle_t blinky_tm; -void led_blinky_cb(TimerHandle_t xTimer); -void usb_device_task(void* param); -void cdc_task(void* params); +static void led_blinky_cb(TimerHandle_t xTimer); +static void usb_device_task(void *param); +void cdc_task(void *params); //--------------------------------------------------------------------+ // Main //--------------------------------------------------------------------+ -int main(void) -{ +int main(void) { board_init(); #if configSUPPORT_STATIC_ALLOCATION @@ -104,8 +104,8 @@ int main(void) xTaskCreateStatic(cdc_task, "cdc", CDC_STACK_SZIE, NULL, configMAX_PRIORITIES-2, cdc_stack, &cdc_taskdef); #else blinky_tm = xTimerCreate(NULL, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), true, NULL, led_blinky_cb); - xTaskCreate( usb_device_task, "usbd", USBD_STACK_SIZE, NULL, configMAX_PRIORITIES-1, NULL); - xTaskCreate( cdc_task, "cdc", CDC_STACK_SZIE, NULL, configMAX_PRIORITIES-2, NULL); + xTaskCreate(usb_device_task, "usbd", USBD_STACK_SIZE, NULL, configMAX_PRIORITIES - 1, NULL); + xTaskCreate(cdc_task, "cdc", CDC_STACK_SZIE, NULL, configMAX_PRIORITIES - 2, NULL); #endif xTimerStart(blinky_tm, 0); @@ -119,16 +119,14 @@ int main(void) } #if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) -void app_main(void) -{ +void app_main(void) { main(); } #endif // USB Device Driver task // This top level thread process all usb events and invoke callbacks -void usb_device_task(void* param) -{ +static void usb_device_task(void *param) { (void) param; // init device stack on configured roothub port @@ -141,8 +139,7 @@ void usb_device_task(void* param) } // RTOS forever loop - while (1) - { + while (1) { // put this thread to waiting state until there is new events tud_task(); @@ -156,35 +153,28 @@ void usb_device_task(void* param) //--------------------------------------------------------------------+ // Invoked when device is mounted -void tud_mount_cb(void) -{ +void tud_mount_cb(void) { xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_MOUNTED), 0); } // Invoked when device is unmounted -void tud_umount_cb(void) -{ +void tud_umount_cb(void) { xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), 0); } // Invoked when usb bus is suspended // remote_wakeup_en : if host allow us to perform remote wakeup // Within 7ms, device must draw an average of current less than 2.5 mA from bus -void tud_suspend_cb(bool remote_wakeup_en) -{ +void tud_suspend_cb(bool remote_wakeup_en) { (void) remote_wakeup_en; xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_SUSPENDED), 0); } // Invoked when usb bus is resumed -void tud_resume_cb(void) -{ - if (tud_mounted()) - { +void tud_resume_cb(void) { + if (tud_mounted()) { xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_MOUNTED), 0); - } - else - { + } else { xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), 0); } } @@ -192,20 +182,17 @@ void tud_resume_cb(void) //--------------------------------------------------------------------+ // USB CDC //--------------------------------------------------------------------+ -void cdc_task(void* params) -{ +void cdc_task(void *params) { (void) params; // RTOS forever loop - while ( 1 ) - { + while (1) { // connected() check for DTR bit // Most but not all terminal client set this when making connection // if ( tud_cdc_connected() ) { // There are data available - while ( tud_cdc_available() ) - { + while (tud_cdc_available()) { uint8_t buf[64]; // read and echo back @@ -228,32 +215,27 @@ void cdc_task(void* params) } // Invoked when cdc when line state changed e.g connected/disconnected -void tud_cdc_line_state_cb(uint8_t itf, bool dtr, bool rts) -{ +void tud_cdc_line_state_cb(uint8_t itf, bool dtr, bool rts) { (void) itf; (void) rts; // TODO set some indicator - if ( dtr ) - { + if (dtr) { // Terminal connected - }else - { + } else { // Terminal disconnected } } // Invoked when CDC interface received data from host -void tud_cdc_rx_cb(uint8_t itf) -{ +void tud_cdc_rx_cb(uint8_t itf) { (void) itf; } //--------------------------------------------------------------------+ // BLINKING TASK //--------------------------------------------------------------------+ -void led_blinky_cb(TimerHandle_t xTimer) -{ +static void led_blinky_cb(TimerHandle_t xTimer) { (void) xTimer; static bool led_state = false; diff --git a/examples/host/bare_api/CMakeLists.txt b/examples/host/bare_api/CMakeLists.txt index 05398b079..76182d6fa 100644 --- a/examples/host/bare_api/CMakeLists.txt +++ b/examples/host/bare_api/CMakeLists.txt @@ -10,6 +10,11 @@ project(${PROJECT} C CXX ASM) # Checks this example is valid for the family and initializes the project family_initialize_project(${PROJECT} ${CMAKE_CURRENT_LIST_DIR}) +# Espressif has its own cmake build system +if(FAMILY STREQUAL "espressif") + return() +endif() + add_executable(${PROJECT}) # Example source diff --git a/examples/host/cdc_msc_hid/CMakeLists.txt b/examples/host/cdc_msc_hid/CMakeLists.txt index ad5751705..a7c372a34 100644 --- a/examples/host/cdc_msc_hid/CMakeLists.txt +++ b/examples/host/cdc_msc_hid/CMakeLists.txt @@ -10,6 +10,11 @@ project(${PROJECT} C CXX ASM) # Checks this example is valid for the family and initializes the project family_initialize_project(${PROJECT} ${CMAKE_CURRENT_LIST_DIR}) +# Espressif has its own cmake build system +if(FAMILY STREQUAL "espressif") + return() +endif() + add_executable(${PROJECT}) # Example source diff --git a/examples/host/cdc_msc_hid_freertos/CMakeLists.txt b/examples/host/cdc_msc_hid_freertos/CMakeLists.txt new file mode 100644 index 000000000..2e95a18e0 --- /dev/null +++ b/examples/host/cdc_msc_hid_freertos/CMakeLists.txt @@ -0,0 +1,36 @@ +cmake_minimum_required(VERSION 3.17) + +include(${CMAKE_CURRENT_SOURCE_DIR}/../../../hw/bsp/family_support.cmake) + +# gets PROJECT name for the example (e.g. -) +family_get_project_name(PROJECT ${CMAKE_CURRENT_LIST_DIR}) + +project(${PROJECT} C CXX ASM) + +# Checks this example is valid for the family and initializes the project +family_initialize_project(${PROJECT} ${CMAKE_CURRENT_LIST_DIR}) + +# Espressif has its own cmake build system +if(FAMILY STREQUAL "espressif") + return() +endif() + +add_executable(${PROJECT}) + +# Example source +target_sources(${PROJECT} PUBLIC + ${CMAKE_CURRENT_SOURCE_DIR}/src/cdc_app.c + ${CMAKE_CURRENT_SOURCE_DIR}/src/freertos_hook.c + ${CMAKE_CURRENT_SOURCE_DIR}/src/hid_app.c + ${CMAKE_CURRENT_SOURCE_DIR}/src/main.c + ${CMAKE_CURRENT_SOURCE_DIR}/src/msc_app.c + ) + +# Example include +target_include_directories(${PROJECT} PUBLIC + ${CMAKE_CURRENT_SOURCE_DIR}/src + ) + +# Configure compilation flags and libraries for the example without RTOS. +# See the corresponding function in hw/bsp/FAMILY/family.cmake for details. +family_configure_host_example(${PROJECT} freertos) diff --git a/examples/host/cdc_msc_hid_freertos/src/CMakeLists.txt b/examples/host/cdc_msc_hid_freertos/src/CMakeLists.txt new file mode 100644 index 000000000..dd7ec8e58 --- /dev/null +++ b/examples/host/cdc_msc_hid_freertos/src/CMakeLists.txt @@ -0,0 +1,4 @@ +# This file is for ESP-IDF only +idf_component_register(SRCS "hid_app.c" "main.c" + INCLUDE_DIRS "." + REQUIRES boards tinyusb_src) diff --git a/examples/host/cdc_msc_hid_freertos/src/main.c b/examples/host/cdc_msc_hid_freertos/src/main.c new file mode 100644 index 000000000..e2ddd52eb --- /dev/null +++ b/examples/host/cdc_msc_hid_freertos/src/main.c @@ -0,0 +1,170 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + */ + +#include +#include +#include + +#include "bsp/board_api.h" +#include "tusb.h" + +#if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) + // ESP-IDF need "freertos/" prefix in include path. + // CFG_TUSB_OS_INC_PATH should be defined accordingly. + #include "freertos/FreeRTOS.h" + #include "freertos/semphr.h" + #include "freertos/queue.h" + #include "freertos/task.h" + #include "freertos/timers.h" + + #define USBH_STACK_SIZE 4096 +#else + #include "FreeRTOS.h" + #include "semphr.h" + #include "queue.h" + #include "task.h" + #include "timers.h" + + // Increase stack size when debug log is enabled + #define USBH_STACK_SIZE (3*configMINIMAL_STACK_SIZE/2) * (CFG_TUSB_DEBUG ? 2 : 1) +#endif + +//--------------------------------------------------------------------+ +// MACRO CONSTANT TYPEDEF PROTOTYPES +//--------------------------------------------------------------------+ +/* Blink pattern + * - 250 ms : device not mounted + * - 1000 ms : device mounted + * - 2500 ms : device is suspended + */ +enum { + BLINK_NOT_MOUNTED = 250, + BLINK_MOUNTED = 1000, + BLINK_SUSPENDED = 2500, +}; + +// static timer & task +#if configSUPPORT_STATIC_ALLOCATION +StaticTimer_t blinky_tmdef; + +StackType_t usb_host_stack[USBH_STACK_SIZE]; +StaticTask_t usb_host_taskdef; + +//StackType_t cdc_stack[CDC_STACK_SZIE]; +//StaticTask_t cdc_taskdef; +#endif + + +TimerHandle_t blinky_tm; + +static void led_blinky_cb(TimerHandle_t xTimer); +static void usb_host_task(void* param); + +extern void cdc_app_task(void); +extern void hid_app_task(void); + +/*------------- MAIN -------------*/ +int main(void) { + board_init(); + + printf("TinyUSB Host CDC MSC HID with FreeRTOS Example\r\n"); + +#if configSUPPORT_STATIC_ALLOCATION + // soft timer for blinky + blinky_tm = xTimerCreateStatic(NULL, pdMS_TO_TICKS(BLINK_MOUNTED), true, NULL, led_blinky_cb, &blinky_tmdef); + + // Create a task for tinyusb device stack + xTaskCreateStatic(usb_host_task, "usbh", USBH_STACK_SIZE, NULL, configMAX_PRIORITIES-1, usb_host_stack, &usb_host_taskdef); + + // Create CDC task + //xTaskCreateStatic(cdc_task, "cdc", CDC_STACK_SZIE, NULL, configMAX_PRIORITIES-2, cdc_stack, &cdc_taskdef); +#else + blinky_tm = xTimerCreate(NULL, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), true, NULL, led_blinky_cb); + xTaskCreate( usb_device_task, "usbd", USBH_STACK_SIZE, NULL, configMAX_PRIORITIES-1, NULL); + //xTaskCreate( cdc_task, "cdc", CDC_STACK_SZIE, NULL, configMAX_PRIORITIES-2, NULL); +#endif + + xTimerStart(blinky_tm, 0); + + // skip starting scheduler (and return) for ESP32-S2 or ESP32-S3 +#if !TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) + vTaskStartScheduler(); +#endif + + return 0; +} + +#if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) +void app_main(void) { + main(); +} +#endif + +// USB Host task +// This top level thread process all usb events and invoke callbacks +static void usb_host_task(void *param) { + (void) param; + + // init host stack on configured roothub port + tuh_init(BOARD_TUH_RHPORT); + + if (board_init_after_tusb) { + board_init_after_tusb(); + } + + // RTOS forever loop + while (1) { + // put this thread to waiting state until there is new events + tuh_task(); + + // following code only run if tuh_task() process at least 1 event + } +} + +//--------------------------------------------------------------------+ +// TinyUSB Callbacks +//--------------------------------------------------------------------+ + +void tuh_mount_cb(uint8_t dev_addr) { + // application set-up + printf("A device with address %d is mounted\r\n", dev_addr); +} + +void tuh_umount_cb(uint8_t dev_addr) { + // application tear-down + printf("A device with address %d is unmounted \r\n", dev_addr); +} + + +//--------------------------------------------------------------------+ +// BLINKING TASK +//--------------------------------------------------------------------+ +static void led_blinky_cb(TimerHandle_t xTimer) { + (void) xTimer; + static bool led_state = false; + + board_led_write(led_state); + led_state = 1 - led_state; // toggle +} diff --git a/examples/host/cdc_msc_hid_freertos/src/tusb_config.h b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h new file mode 100644 index 000000000..1bed9a9b3 --- /dev/null +++ b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h @@ -0,0 +1,133 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + */ + +#ifndef _TUSB_CONFIG_H_ +#define _TUSB_CONFIG_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +//--------------------------------------------------------------------+ +// Board Specific Configuration +//--------------------------------------------------------------------+ + +#if CFG_TUSB_MCU == OPT_MCU_RP2040 + // change to 1 if using pico-pio-usb as host controller for raspberry rp2040 + #define CFG_TUH_RPI_PIO_USB 0 + #define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB +#endif + +// RHPort number used for host can be defined by board.mk, default to port 0 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED +#endif + +//-------------------------------------------------------------------- +// COMMON CONFIGURATION +//-------------------------------------------------------------------- + +// defined by compiler flags for flexibility +#ifndef CFG_TUSB_MCU +#error CFG_TUSB_MCU must be defined +#endif + +#ifndef CFG_TUSB_OS +#define CFG_TUSB_OS OPT_OS_FREERTOS +#endif + +// Espressif IDF requires "freertos/" prefix in include path +#if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) +#define CFG_TUSB_OS_INC_PATH freertos/ +#endif + +#ifndef CFG_TUSB_DEBUG +#define CFG_TUSB_DEBUG 0 +#endif + +// Enable Host stack +#define CFG_TUH_ENABLED 1 + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED + +/* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. + * Tinyusb use follows macros to declare transferring memory so that they can be put + * into those specific section. + * e.g + * - CFG_TUSB_MEM SECTION : __attribute__ (( section(".usb_ram") )) + * - CFG_TUSB_MEM_ALIGN : __attribute__ ((aligned(4))) + */ +#ifndef CFG_TUH_MEM_SECTION +#define CFG_TUH_MEM_SECTION +#endif + +#ifndef CFG_TUH_MEM_ALIGN +#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#endif + +//-------------------------------------------------------------------- +// CONFIGURATION +//-------------------------------------------------------------------- + +// Size of buffer to hold descriptors and other data used for enumeration +#define CFG_TUH_ENUMERATION_BUFSIZE 256 + +#define CFG_TUH_HUB 1 // number of supported hubs +#define CFG_TUH_CDC 1 // CDC ACM +#define CFG_TUH_CDC_FTDI 1 // FTDI Serial. FTDI is not part of CDC class, only to re-use CDC driver API +#define CFG_TUH_CDC_CP210X 1 // CP210x Serial. CP210X is not part of CDC class, only to re-use CDC driver API +#define CFG_TUH_HID (3*CFG_TUH_DEVICE_MAX) // typical keyboard + mouse device can have 3-4 HID interfaces +#define CFG_TUH_MSC 1 +#define CFG_TUH_VENDOR 0 + +// max device support (excluding hub device): 1 hub typically has 4 ports +#define CFG_TUH_DEVICE_MAX (3*CFG_TUH_HUB + 1) + +//------------- HID -------------// +#define CFG_TUH_HID_EPIN_BUFSIZE 64 +#define CFG_TUH_HID_EPOUT_BUFSIZE 64 + +//------------- CDC -------------// + +// Set Line Control state on enumeration/mounted: +// DTR ( bit 0), RTS (bit 1) +#define CFG_TUH_CDC_LINE_CONTROL_ON_ENUM 0x03 + +// Set Line Coding on enumeration/mounted, value for cdc_line_coding_t +// bit rate = 115200, 1 stop bit, no parity, 8 bit data width +#define CFG_TUH_CDC_LINE_CODING_ON_ENUM { 115200, CDC_LINE_CONDING_STOP_BITS_1, CDC_LINE_CODING_PARITY_NONE, 8 } + + +#ifdef __cplusplus + } +#endif + +#endif /* _TUSB_CONFIG_H_ */ diff --git a/examples/host/hid_controller/CMakeLists.txt b/examples/host/hid_controller/CMakeLists.txt index 3fb630aaa..c1b500dd8 100644 --- a/examples/host/hid_controller/CMakeLists.txt +++ b/examples/host/hid_controller/CMakeLists.txt @@ -10,6 +10,11 @@ project(${PROJECT} C CXX ASM) # Checks this example is valid for the family and initializes the project family_initialize_project(${PROJECT} ${CMAKE_CURRENT_LIST_DIR}) +# Espressif has its own cmake build system +if(FAMILY STREQUAL "espressif") + return() +endif() + add_executable(${PROJECT}) # Example source diff --git a/examples/host/msc_file_explorer/CMakeLists.txt b/examples/host/msc_file_explorer/CMakeLists.txt index 1868b632e..1a57c7466 100644 --- a/examples/host/msc_file_explorer/CMakeLists.txt +++ b/examples/host/msc_file_explorer/CMakeLists.txt @@ -10,6 +10,11 @@ project(${PROJECT} C CXX ASM) # Checks this example is valid for the family and initializes the project family_initialize_project(${PROJECT} ${CMAKE_CURRENT_LIST_DIR}) +# Espressif has its own cmake build system +if(FAMILY STREQUAL "espressif") + return() +endif() + add_executable(${PROJECT}) # Example source diff --git a/examples/make.mk b/examples/make.mk index 8fe4a3486..448d7883d 100644 --- a/examples/make.mk +++ b/examples/make.mk @@ -26,9 +26,6 @@ ifeq '$(findstring ;,$(PATH))' ';' CMDEXE := 1 # makefile shell commands should use syntax for DOS CMD, not unix sh -# Unfortunately, SHELL may point to sh or bash, which can't accept DOS syntax. -# We can't just use sh, because while sh and/or bash shell may be available, -# many Windows environments won't have utilities like realpath used below, so... # Force DOS command shell on Windows. SHELL := cmd.exe endif diff --git a/hw/bsp/espressif/boards/adafruit_metro_esp32s2/board.h b/hw/bsp/espressif/boards/adafruit_metro_esp32s2/board.h index 2ec80ef47..44ff11aa0 100644 --- a/hw/bsp/espressif/boards/adafruit_metro_esp32s2/board.h +++ b/hw/bsp/espressif/boards/adafruit_metro_esp32s2/board.h @@ -36,6 +36,14 @@ #define BUTTON_PIN 0 #define BUTTON_STATE_ACTIVE 0 +// SPI for USB host shield +#define MAX3421_SPI_HOST SPI2_HOST +#define MAX3421_SCK_PIN 36 +#define MAX3421_MOSI_PIN 35 +#define MAX3421_MISO_PIN 37 +#define MAX3421_CS_PIN 15 +#define MAX3421_INTR_PIN 14 + #ifdef __cplusplus } #endif diff --git a/hw/bsp/espressif/boards/espressif_kaluga_1/board.h b/hw/bsp/espressif/boards/espressif_kaluga_1/board.h index 0acb9c439..613e6ae0c 100644 --- a/hw/bsp/espressif/boards/espressif_kaluga_1/board.h +++ b/hw/bsp/espressif/boards/espressif_kaluga_1/board.h @@ -37,6 +37,14 @@ #define BUTTON_PIN 0 #define BUTTON_STATE_ACTIVE 0 +// SPI for USB host shield +#define MAX3421_SPI_HOST SPI2_HOST +#define MAX3421_SCK_PIN 36 +#define MAX3421_MOSI_PIN 35 +#define MAX3421_MISO_PIN 37 +#define MAX3421_CS_PIN 15 +#define MAX3421_INTR_PIN 14 + #ifdef __cplusplus } #endif diff --git a/hw/bsp/espressif/boards/espressif_s2_devkitc/board.cmake b/hw/bsp/espressif/boards/espressif_s2_devkitc/board.cmake new file mode 100644 index 000000000..abbdf7abc --- /dev/null +++ b/hw/bsp/espressif/boards/espressif_s2_devkitc/board.cmake @@ -0,0 +1,2 @@ +# Apply board specific content here +set(IDF_TARGET "esp32s2") diff --git a/hw/bsp/espressif/boards/espressif_s2_devkitc/board.h b/hw/bsp/espressif/boards/espressif_s2_devkitc/board.h new file mode 100644 index 000000000..e068efef9 --- /dev/null +++ b/hw/bsp/espressif/boards/espressif_s2_devkitc/board.h @@ -0,0 +1,45 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +// Note: On the production version (v1.2) WS2812 is connected to GPIO 18, +// however earlier revision v1.1 WS2812 is connected to GPIO 17 +#define NEOPIXEL_PIN 18 + +#define BUTTON_PIN 0 +#define BUTTON_STATE_ACTIVE 0 + +#ifdef __cplusplus + } +#endif + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/espressif/boards/family.c b/hw/bsp/espressif/boards/family.c index 8f857fb71..250b7001e 100644 --- a/hw/bsp/espressif/boards/family.c +++ b/hw/bsp/espressif/boards/family.c @@ -45,16 +45,19 @@ static led_strip_t *strip; #endif -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM DECLARATION -//--------------------------------------------------------------------+ +#if CFG_TUH_ENABLED && CFG_TUH_MAX3421 +#include "driver/spi_master.h" +static void max3421_init(void); +#endif static void configure_pins(usb_hal_context_t *usb); -// Initialize on-board peripherals : led, button, uart and USB -void board_init(void) -{ +//--------------------------------------------------------------------+ +// Implementation +//--------------------------------------------------------------------+ +// Initialize on-board peripherals : led, button, uart and USB +void board_init(void) { #ifdef NEOPIXEL_PIN #ifdef NEOPIXEL_POWER_PIN gpio_reset_pin(NEOPIXEL_POWER_PIN); @@ -79,23 +82,27 @@ void board_init(void) gpio_set_direction(BUTTON_PIN, GPIO_MODE_INPUT); gpio_set_pull_mode(BUTTON_PIN, BUTTON_STATE_ACTIVE ? GPIO_PULLDOWN_ONLY : GPIO_PULLUP_ONLY); +#if CFG_TUD_ENABLED // USB Controller Hal init periph_module_reset(PERIPH_USB_MODULE); periph_module_enable(PERIPH_USB_MODULE); usb_hal_context_t hal = { - .use_external_phy = false // use built-in PHY + .use_external_phy = false // use built-in PHY }; usb_hal_init(&hal); configure_pins(&hal); +#endif + +#if CFG_TUH_ENABLED && CFG_TUH_MAX3421 + max3421_init(); +#endif } -static void configure_pins(usb_hal_context_t *usb) -{ +static void configure_pins(usb_hal_context_t *usb) { /* usb_periph_iopins currently configures USB_OTG as USB Device. * Introduce additional parameters in usb_hal_context_t when adding support - * for USB Host. - */ + * for USB Host. */ for (const usb_iopin_dsc_t *iopin = usb_periph_iopins; iopin->pin != -1; ++iopin) { if ((usb->use_external_phy) || (iopin->ext_phy_only == 0)) { esp_rom_gpio_pad_select_gpio(iopin->pin); @@ -115,6 +122,7 @@ static void configure_pins(usb_hal_context_t *usb) esp_rom_gpio_pad_unhold(iopin->pin); } } + if (!usb->use_external_phy) { gpio_set_drive_capability(USBPHY_DM_NUM, GPIO_DRIVE_CAP_3); gpio_set_drive_capability(USBPHY_DP_NUM, GPIO_DRIVE_CAP_3); @@ -122,8 +130,7 @@ static void configure_pins(usb_hal_context_t *usb) } // Turn LED on or off -void board_led_write(bool state) -{ +void board_led_write(bool state) { #ifdef NEOPIXEL_PIN strip->set_pixel(strip, 0, (state ? 0x88 : 0x00), 0x00, 0x00); strip->refresh(strip, 100); @@ -132,21 +139,102 @@ void board_led_write(bool state) // Get the current state of button // a '1' means active (pressed), a '0' means inactive. -uint32_t board_button_read(void) -{ +uint32_t board_button_read(void) { return gpio_get_level(BUTTON_PIN) == BUTTON_STATE_ACTIVE; } // Get characters from UART -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; +int board_uart_read(uint8_t *buf, int len) { + (void) buf; + (void) len; return 0; } // Send characters to UART -int board_uart_write(void const * buf, int len) -{ - (void) buf; (void) len; +int board_uart_write(void const *buf, int len) { + (void) buf; + (void) len; return 0; } + +//--------------------------------------------------------------------+ +// API: SPI transfer with MAX3421E, must be implemented by application +//--------------------------------------------------------------------+ +#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 + +static spi_device_handle_t max3421_spi; + +static void IRAM_ATTR max3421_isr_handler(void* arg) +{ + (void) arg; + //uint32_t gpio_num = (uint32_t) arg; + //xQueueSendFromISR(gpio_evt_queue, &gpio_num, NULL); + tuh_int_handler(1); +} + +static void max3421_init(void) { + // CS pin + gpio_set_direction(MAX3421_CS_PIN, GPIO_MODE_OUTPUT); + gpio_set_level(MAX3421_CS_PIN, 1); + + // SPI + spi_bus_config_t buscfg={ + .miso_io_num = MAX3421_MISO_PIN, + .mosi_io_num = MAX3421_MOSI_PIN, + .sclk_io_num = MAX3421_SCK_PIN, + .quadwp_io_num = -1, + .quadhd_io_num = -1, + .data4_io_num = -1, + .data5_io_num = -1, + .data6_io_num = -1, + .data7_io_num = -1, + .max_transfer_sz = 128 + }; + ESP_ERROR_CHECK( spi_bus_initialize(MAX3421_SPI_HOST, &buscfg, SPI_DMA_CH_AUTO) ); + + spi_device_interface_config_t max3421_cfg = { + .command_bits = 8, + .mode = 0, + .clock_speed_hz = 4000000, // 26000000 + .spics_io_num = -1, // manual control CS + .queue_size = 1 + }; + ESP_ERROR_CHECK( spi_bus_add_device(MAX3421_SPI_HOST, &max3421_cfg, &max3421_spi) ); + + // Interrupt pin +// gpio_set_direction(MAX3421_INTR_PIN, GPIO_MODE_INPUT); +// gpio_set_intr_type(MAX3421_INTR_PIN, GPIO_INTR_NEGEDGE); +// +// gpio_install_isr_service(ESP_INTR_FLAG_EDGE); +// gpio_isr_handler_add(MAX3421_INTR_PIN, max3421_isr_handler, NULL); +} + +void tuh_max3421_int_api(uint8_t rhport, bool enabled) { + (void) rhport; + if (enabled) { + gpio_intr_enable(MAX3421_INTR_PIN); + } else { + gpio_intr_disable(MAX3421_INTR_PIN); + } +} + +void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { + (void) rhport; + gpio_set_level(MAX3421_CS_PIN, active ? 0 : 1); +} + +bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_len, uint8_t *rx_buf, size_t rx_len) { + (void) rhport; + + spi_transaction_t xact = { + .length = tx_len, + .rxlength = rx_len, + .tx_buffer = tx_buf, + .rx_buffer = rx_buf + }; + + ESP_ERROR_CHECK(spi_device_transmit(max3421_spi, &xact)); + return true; +} + +#endif diff --git a/hw/bsp/espressif/components/tinyusb_src/CMakeLists.txt b/hw/bsp/espressif/components/tinyusb_src/CMakeLists.txt index bf8e45be2..2a154a8ff 100644 --- a/hw/bsp/espressif/components/tinyusb_src/CMakeLists.txt +++ b/hw/bsp/espressif/components/tinyusb_src/CMakeLists.txt @@ -16,40 +16,57 @@ else() return() endif() -list(APPEND compile_options - "-DCFG_TUSB_MCU=${tusb_mcu}" - "-DCFG_TUSB_OS=OPT_OS_FREERTOS" - #"-DCFG_TUSB_DEBUG=1" - ) +list(APPEND compile_definitions + CFG_TUSB_MCU=${tusb_mcu} + CFG_TUSB_OS=OPT_OS_FREERTOS + ) -idf_component_get_property(freertos_component_dir freertos COMPONENT_DIR) +list(APPEND srcs + # common + ${tusb_src}/tusb.c + ${tusb_src}/common/tusb_fifo.c + # device + ${tusb_src}/device/usbd.c + ${tusb_src}/device/usbd_control.c + ${tusb_src}/class/audio/audio_device.c + ${tusb_src}/class/cdc/cdc_device.c + ${tusb_src}/class/dfu/dfu_device.c + ${tusb_src}/class/dfu/dfu_rt_device.c + ${tusb_src}/class/hid/hid_device.c + ${tusb_src}/class/midi/midi_device.c + ${tusb_src}/class/msc/msc_device.c + ${tusb_src}/class/net/ecm_rndis_device.c + ${tusb_src}/class/net/ncm_device.c + ${tusb_src}/class/usbtmc/usbtmc_device.c + ${tusb_src}/class/vendor/vendor_device.c + ${tusb_src}/class/video/video_device.c + ${tusb_src}/portable/synopsys/dwc2/dcd_dwc2.c + # host + ${tusb_src}/host/usbh.c + ${tusb_src}/host/hub.c + ${tusb_src}/class/cdc/cdc_host.c + ${tusb_src}/class/hid/hid_host.c + ${tusb_src}/class/msc/msc_host.c + ${tusb_src}/class/vendor/vendor_host.c + ) -list(APPEND includes_public - "${tusb_src}" - # The FreeRTOS API include convention in tinyusb is different from esp-idf - #"${freertos_component_dir}/include/freertos" - ) +# use max3421 as host controller +if (MAX3421_HOST STREQUAL "1") + list(APPEND srcs ${tusb_src}/portable/analog/max3421/hcd_max3421.c) + list(APPEND compile_definitions CFG_TUH_MAX3421=1) +endif () -list(APPEND srcs - "${tusb_src}/tusb.c" - "${tusb_src}/common/tusb_fifo.c" - "${tusb_src}/device/usbd.c" - "${tusb_src}/device/usbd_control.c" - "${tusb_src}/class/cdc/cdc_device.c" - "${tusb_src}/class/dfu/dfu_rt_device.c" - "${tusb_src}/class/hid/hid_device.c" - "${tusb_src}/class/midi/midi_device.c" - "${tusb_src}/class/msc/msc_device.c" - "${tusb_src}/class/net/ecm_rndis_device.c" - "${tusb_src}/class/net/ncm_device.c" - "${tusb_src}/class/usbtmc/usbtmc_device.c" - "${tusb_src}/class/vendor/vendor_device.c" - "${tusb_src}/portable/synopsys/dwc2/dcd_dwc2.c" - ) +if (DEFINED LOG) + list(APPEND compile_definitions CFG_TUSB_DEBUG=${LOG}) + if (LOG STREQUAL "4") + # no inline for debug level 4 + list(APPEND compile_definitions TU_ATTR_ALWAYS_INLINE=) + endif () +endif() idf_component_register(SRCS ${srcs} - INCLUDE_DIRS ${includes_public} - REQUIRES src - ) + INCLUDE_DIRS ${tusb_src} + REQUIRES src + ) -target_compile_options(${COMPONENT_LIB} PUBLIC ${compile_options}) +target_compile_definitions(${COMPONENT_LIB} PUBLIC ${compile_definitions}) diff --git a/src/host/usbh.c b/src/host/usbh.c index e332f35cc..dc2831da3 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -659,7 +659,7 @@ static bool usbh_control_xfer_cb (uint8_t dev_addr, uint8_t ep_addr, xfer_result tusb_control_request_t const * request = &_ctrl_xfer.request; if (XFER_RESULT_SUCCESS != result) { - TU_LOG1("[%u:%u] Control %s, xferred_bytes = %lu\r\n", rhport, dev_addr, result == XFER_RESULT_STALLED ? "STALLED" : "FAILED", xferred_bytes); + TU_LOG1("[%u:%u] Control %s, xferred_bytes = %u\r\n", rhport, dev_addr, result == XFER_RESULT_STALLED ? "STALLED" : "FAILED", xferred_bytes); TU_LOG1_BUF(request, 8); TU_LOG1("\r\n"); diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index f3f76fd58..3f6747404 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -882,7 +882,7 @@ void hcd_int_handler(uint8_t rhport) { if ( hirq & HIRQ_RCVDAV_IRQ ) { uint8_t const ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, 1); - uint8_t xact_len; + uint8_t xact_len = 0; // RCVDAV_IRQ can trigger 2 times (dual buffered) while ( hirq & HIRQ_RCVDAV_IRQ ) { -- cgit v1.3.1 From 1168e4e16343cc0a6d958899460f1b841624974f Mon Sep 17 00:00:00 2001 From: bac Date: Tue, 26 Sep 2023 15:27:17 +0100 Subject: Added support for USB2 HS peripheral (with integrated HS PHY) on STM32U59x chips --- src/portable/synopsys/dwc2/dwc2_stm32.h | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dwc2_stm32.h b/src/portable/synopsys/dwc2/dwc2_stm32.h index cb455bd90..aa77511fa 100644 --- a/src/portable/synopsys/dwc2/dwc2_stm32.h +++ b/src/portable/synopsys/dwc2/dwc2_stm32.h @@ -84,7 +84,17 @@ #elif CFG_TUSB_MCU == OPT_MCU_STM32U5 #include "stm32u5xx.h" - #define USB_OTG_FS_PERIPH_BASE USB_OTG_FS_BASE + // NOTE: STM595/5A5/599/5A9 only have 1 USB port (with integrated HS PHY) + // USB_OTG_FS_BASE and OTG_FS_IRQn not defined + #if (! defined USB_OTG_FS) + #define USB_OTG_HS_PERIPH_BASE USB_OTG_HS_BASE + #define EP_MAX_HS 9 + #define EP_FIFO_SIZE_HS 4096 + #define USB_OTG_FS_PERIPH_BASE USB_OTG_HS_BASE + #define OTG_FS_IRQn OTG_HS_IRQn + #else + #define USB_OTG_FS_PERIPH_BASE USB_OTG_FS_BASE + #endif #define EP_MAX_FS 6 #define EP_FIFO_SIZE_FS 1280 -- cgit v1.3.1 From 2f6592de7f94851cfcca411242398c5da7b792de Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 27 Sep 2023 11:30:18 +0700 Subject: update max3421 to have hcd_int_handler_ext() --- hw/bsp/espressif/boards/family.c | 22 ++++++++++- src/host/hcd.h | 3 ++ src/portable/analog/max3421/hcd_max3421.c | 62 ++++++++++++++++--------------- 3 files changed, 55 insertions(+), 32 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/espressif/boards/family.c b/hw/bsp/espressif/boards/family.c index d96d86670..a04e1e7c5 100644 --- a/hw/bsp/espressif/boards/family.c +++ b/hw/bsp/espressif/boards/family.c @@ -167,15 +167,30 @@ int board_getchar(void) { #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 static spi_device_handle_t max3421_spi; +SemaphoreHandle_t max3421_intr_sem; static void IRAM_ATTR max3421_isr_handler(void* arg) { (void) arg; // arg is gpio num - //xQueueSendFromISR(gpio_evt_queue, &gpio_num, NULL); gpio_set_level(13, 1); - tuh_int_handler(1); + + BaseType_t xHigherPriorityTaskWoken = pdFALSE; + xSemaphoreGiveFromISR(max3421_intr_sem, &xHigherPriorityTaskWoken); + if (xHigherPriorityTaskWoken) { + portYIELD_FROM_ISR(); + } + gpio_set_level(13, 0); } +static void max3421_intr_task(void* param) { + (void) param; + + while (1) { + xSemaphoreTake(max3421_intr_sem, portMAX_DELAY); + tuh_int_handler(BOARD_TUH_RHPORT); + } +} + static void max3421_init(void) { // CS pin gpio_set_direction(MAX3421_CS_PIN, GPIO_MODE_OUTPUT); @@ -209,6 +224,9 @@ static void max3421_init(void) { gpio_set_level(13, 0); // Interrupt pin + max3421_intr_sem = xSemaphoreCreateBinary(); + xTaskCreate(max3421_intr_task, "max3421 intr", 2048, NULL, configMAX_PRIORITIES-1, NULL); + gpio_set_direction(MAX3421_INTR_PIN, GPIO_MODE_INPUT); gpio_set_intr_type(MAX3421_INTR_PIN, GPIO_INTR_NEGEDGE); diff --git a/src/host/hcd.h b/src/host/hcd.h index e25b20ea3..a2d4da85d 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -133,6 +133,9 @@ bool hcd_init(uint8_t rhport); // Interrupt Handler void hcd_int_handler(uint8_t rhport); +// Interrupt Hanndler (extended version) +void hcd_int_handler_ext(uint8_t rhport, bool in_isr); + // Enable USB interrupt void hcd_int_enable (uint8_t rhport); diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 3f6747404..652a971ee 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -428,8 +428,8 @@ bool hcd_init(uint8_t rhport) { reg_write(rhport, PINCTL_ADDR, PINCTL_FDUPSPI, false); // V1 is 0x01, V2 is 0x12, V3 is 0x13 - // uint8_t const revision = reg_read(rhport, REVISION_ADDR, false); - // TU_LOG2_HEX(revision); + uint8_t const revision = reg_read(rhport, REVISION_ADDR, false); + TU_LOG2_HEX(revision); // reset reg_write(rhport, USBCTL_ADDR, USBCTL_CHIPRES, false); @@ -693,9 +693,7 @@ static void handle_connect_irq(uint8_t rhport, bool in_isr) { // port reset anyway, this will help to stable bus signal for next connection reg_write(rhport, HCTL_ADDR, HCTL_BUSRST, in_isr); - hcd_event_device_remove(rhport, in_isr); - reg_write(rhport, HCTL_ADDR, 0, in_isr); break; @@ -721,13 +719,12 @@ static void handle_connect_irq(uint8_t rhport, bool in_isr) { free_ep(daddr); hcd_event_device_attach(rhport, in_isr); - break; } } } -static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t result, uint8_t hrsl) { +static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t result, uint8_t hrsl, bool in_isr) { uint8_t const ep_addr = tu_edpt_addr(ep->ep_num, ep->ep_dir); // save data toggle @@ -738,20 +735,20 @@ static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t re } ep->xfer_pending = 0; - hcd_event_xfer_complete(ep->daddr, ep_addr, ep->xferred_len, result, true); + hcd_event_xfer_complete(ep->daddr, ep_addr, ep->xferred_len, result, in_isr); // Find next pending endpoint max3421_ep_t *next_ep = find_next_pending_ep(ep); if (next_ep) { - xact_inout(rhport, next_ep, true, true); + xact_inout(rhport, next_ep, true, in_isr); }else { // no more pending atomic_flag_clear(&_hcd_data.busy); } } -static void handle_xfer_done(uint8_t rhport) { - uint8_t const hrsl = reg_read(rhport, HRSL_ADDR, true); +static void handle_xfer_done(uint8_t rhport, bool in_isr) { + uint8_t const hrsl = reg_read(rhport, HRSL_ADDR, in_isr); uint8_t const hresult = hrsl & HRSL_RESULT_MASK; uint8_t const ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; @@ -774,17 +771,17 @@ static void handle_xfer_done(uint8_t rhport) { case HRSL_NAK: if (ep_num == 0) { // NAK on control, retry immediately - hxfr_write(rhport, _hcd_data.hxfr, true); + hxfr_write(rhport, _hcd_data.hxfr, in_isr); }else { // NAK on non-control, find next pending to switch max3421_ep_t *next_ep = find_next_pending_ep(ep); if (ep == next_ep) { // this endpoint is only one pending, retry immediately - hxfr_write(rhport, _hcd_data.hxfr, true); + hxfr_write(rhport, _hcd_data.hxfr, in_isr); }else if (next_ep) { // switch to next pending TODO could have issue with double buffered if not clear previously out data - xact_inout(rhport, next_ep, true, true); + xact_inout(rhport, next_ep, true, in_isr); }else { TU_ASSERT(false,); } @@ -802,7 +799,7 @@ static void handle_xfer_done(uint8_t rhport) { } if (xfer_result != XFER_RESULT_SUCCESS) { - xfer_complete_isr(rhport, ep, xfer_result, hrsl); + xfer_complete_isr(rhport, ep, xfer_result, hrsl, in_isr); return; } @@ -814,10 +811,10 @@ static void handle_xfer_done(uint8_t rhport) { // short packet or all bytes transferred if ( ep->xfer_complete ) { - xfer_complete_isr(rhport, ep, xfer_result, hrsl); + xfer_complete_isr(rhport, ep, xfer_result, hrsl, in_isr); }else { // more to transfer - hxfr_write(rhport, _hcd_data.hxfr, true); + hxfr_write(rhport, _hcd_data.hxfr, in_isr); } } else { // SETUP or OUT transfer @@ -835,10 +832,10 @@ static void handle_xfer_done(uint8_t rhport) { ep->buf += xact_len; if (xact_len < ep->packet_size || ep->xferred_len >= ep->total_len) { - xfer_complete_isr(rhport, ep, xfer_result, hrsl); + xfer_complete_isr(rhport, ep, xfer_result, hrsl, in_isr); } else { // more to transfer - xact_out(rhport, ep, false, true); + xact_out(rhport, ep, false, in_isr); } } } @@ -862,9 +859,9 @@ void print_hirq(uint8_t hirq) { #define print_hirq(hirq) #endif -// Interrupt Handler -void hcd_int_handler(uint8_t rhport) { - uint8_t hirq = reg_read(rhport, HIRQ_ADDR, true) & _hcd_data.hien; +// Interrupt handler (extended) +void hcd_int_handler_ext(uint8_t rhport, bool in_isr) { + uint8_t hirq = reg_read(rhport, HIRQ_ADDR, in_isr) & _hcd_data.hien; if (!hirq) return; // print_hirq(hirq); @@ -873,7 +870,7 @@ void hcd_int_handler(uint8_t rhport) { } if (hirq & HIRQ_CONDET_IRQ) { - handle_connect_irq(rhport, true); + handle_connect_irq(rhport, in_isr); } // queue more transfer in handle_xfer_done() can cause hirq to be set again while external IRQ may not catch and/or @@ -886,17 +883,17 @@ void hcd_int_handler(uint8_t rhport) { // RCVDAV_IRQ can trigger 2 times (dual buffered) while ( hirq & HIRQ_RCVDAV_IRQ ) { - uint8_t rcvbc = reg_read(rhport, RCVBC_ADDR, true); + uint8_t rcvbc = reg_read(rhport, RCVBC_ADDR, in_isr); xact_len = (uint8_t) tu_min16(rcvbc, ep->total_len - ep->xferred_len); if ( xact_len ) { - fifo_read(rhport, ep->buf, xact_len, true); + fifo_read(rhport, ep->buf, xact_len, in_isr); ep->buf += xact_len; ep->xferred_len += xact_len; } // ack RCVDVAV IRQ - hirq_write(rhport, HIRQ_RCVDAV_IRQ, true); - hirq = reg_read(rhport, HIRQ_ADDR, true); + hirq_write(rhport, HIRQ_RCVDAV_IRQ, in_isr); + hirq = reg_read(rhport, HIRQ_ADDR, in_isr); } if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { @@ -905,18 +902,23 @@ void hcd_int_handler(uint8_t rhport) { } if ( hirq & HIRQ_HXFRDN_IRQ ) { - hirq_write(rhport, HIRQ_HXFRDN_IRQ, true); - handle_xfer_done(rhport); + hirq_write(rhport, HIRQ_HXFRDN_IRQ, in_isr); + handle_xfer_done(rhport, in_isr); } - hirq = reg_read(rhport, HIRQ_ADDR, true); + hirq = reg_read(rhport, HIRQ_ADDR, in_isr); } // clear all interrupt except SNDBAV_IRQ (never clear by us). Note RCVDAV_IRQ, HXFRDN_IRQ already clear while processing hirq &= ~HIRQ_SNDBAV_IRQ; if ( hirq ) { - hirq_write(rhport, hirq, true); + hirq_write(rhport, hirq, in_isr); } } +// Interrupt Handler +void hcd_int_handler(uint8_t rhport) { + hcd_int_handler_ext(rhport, true); +} + #endif -- cgit v1.3.1 From 3b0ffd0f488671f1bafa4bcd9e22dd51f8bb6dee Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 27 Sep 2023 15:51:03 +0700 Subject: change hcd_int_handler(rhport, in_isr) signature: add in_isr change tuh_int_handler() to take in_isr as optional parameter (default = true) --- examples/host/bare_api/only.txt | 1 + examples/host/cdc_msc_hid/only.txt | 1 + examples/host/hid_controller/only.txt | 1 + examples/host/msc_file_explorer/only.txt | 1 + hw/bsp/imxrt/family.c | 4 +- hw/bsp/kinetis_kl/family.c | 2 +- hw/bsp/kinetis_kl/family.cmake | 75 ++++++++++---------- .../lpc17/boards/lpcxpresso1769/lpcxpresso1769.c | 2 +- hw/bsp/lpc17/boards/mbed1768/mbed1768.c | 2 +- hw/bsp/lpc18/family.c | 55 ++++++--------- hw/bsp/lpc40/family.c | 2 +- hw/bsp/lpc43/family.c | 4 +- hw/bsp/msp432e4/family.c | 2 +- hw/bsp/ngx4330/ngx4330.c | 4 +- hw/bsp/nrf/family.c | 2 +- hw/bsp/ra/family.c | 6 +- hw/bsp/rx/boards/rx65n_target/rx65n_target.c | 2 +- hw/bsp/samd21/family.c | 2 +- hw/bsp/samd51/family.c | 2 +- hw/bsp/stm32g4/family.cmake | 81 +++++++++++----------- hw/bsp/tm4c123/family.c | 2 +- src/common/tusb_common.h | 2 - src/common/tusb_timeout.h | 80 --------------------- src/common/tusb_verify.h | 52 +++++--------- src/host/hcd.h | 2 +- src/host/usbh.h | 11 ++- src/portable/analog/max3421/hcd_max3421.c | 3 +- src/portable/ehci/ehci.c | 4 +- src/portable/mentor/musb/hcd_musb.c | 4 +- src/portable/nxp/khci/hcd_khci.c | 7 +- src/portable/ohci/ohci.c | 5 +- src/portable/raspberrypi/rp2040/hcd_rp2040.c | 4 +- src/portable/renesas/rusb2/hcd_rusb2.c | 5 +- src/portable/template/hcd_template.c | 3 +- src/tusb.h | 4 +- 35 files changed, 172 insertions(+), 267 deletions(-) delete mode 100644 src/common/tusb_timeout.h (limited to 'src/portable') diff --git a/examples/host/bare_api/only.txt b/examples/host/bare_api/only.txt index 3837ac8a2..fee10f9e2 100644 --- a/examples/host/bare_api/only.txt +++ b/examples/host/bare_api/only.txt @@ -1,3 +1,4 @@ +mcu:KINETIS_KL mcu:LPC175X_6X mcu:LPC177X_8X mcu:LPC18XX diff --git a/examples/host/cdc_msc_hid/only.txt b/examples/host/cdc_msc_hid/only.txt index 3837ac8a2..fee10f9e2 100644 --- a/examples/host/cdc_msc_hid/only.txt +++ b/examples/host/cdc_msc_hid/only.txt @@ -1,3 +1,4 @@ +mcu:KINETIS_KL mcu:LPC175X_6X mcu:LPC177X_8X mcu:LPC18XX diff --git a/examples/host/hid_controller/only.txt b/examples/host/hid_controller/only.txt index 3837ac8a2..fee10f9e2 100644 --- a/examples/host/hid_controller/only.txt +++ b/examples/host/hid_controller/only.txt @@ -1,3 +1,4 @@ +mcu:KINETIS_KL mcu:LPC175X_6X mcu:LPC177X_8X mcu:LPC18XX diff --git a/examples/host/msc_file_explorer/only.txt b/examples/host/msc_file_explorer/only.txt index 3837ac8a2..fee10f9e2 100644 --- a/examples/host/msc_file_explorer/only.txt +++ b/examples/host/msc_file_explorer/only.txt @@ -1,3 +1,4 @@ +mcu:KINETIS_KL mcu:LPC175X_6X mcu:LPC177X_8X mcu:LPC18XX diff --git a/hw/bsp/imxrt/family.c b/hw/bsp/imxrt/family.c index ec95a8b24..32d89f794 100644 --- a/hw/bsp/imxrt/family.c +++ b/hw/bsp/imxrt/family.c @@ -188,7 +188,7 @@ void USB_OTG1_IRQHandler(void) #endif #if PORT_SUPPORT_HOST(0) - tuh_int_handler(0); + tuh_int_handler(0, true); #endif } @@ -199,7 +199,7 @@ void USB_OTG2_IRQHandler(void) #endif #if PORT_SUPPORT_HOST(1) - tuh_int_handler(1); + tuh_int_handler(1, true); #endif } diff --git a/hw/bsp/kinetis_kl/family.c b/hw/bsp/kinetis_kl/family.c index 3e9aa83a4..c436be3e6 100644 --- a/hw/bsp/kinetis_kl/family.c +++ b/hw/bsp/kinetis_kl/family.c @@ -39,7 +39,7 @@ void USB0_IRQHandler(void) { #if CFG_TUH_ENABLED - tuh_int_handler(0); + tuh_int_handler(0, true); #endif #if CFG_TUD_ENABLED tud_int_handler(0); diff --git a/hw/bsp/kinetis_kl/family.cmake b/hw/bsp/kinetis_kl/family.cmake index 793ef1783..4151979a0 100644 --- a/hw/bsp/kinetis_kl/family.cmake +++ b/hw/bsp/kinetis_kl/family.cmake @@ -22,48 +22,47 @@ set(FAMILY_MCUS KINETIS_KL CACHE INTERNAL "") #------------------------------------ # only need to be built ONCE for all examples function(add_board_target BOARD_TARGET) - if (NOT TARGET ${BOARD_TARGET}) - add_library(${BOARD_TARGET} STATIC - ${SDK_DIR}/drivers/gpio/fsl_gpio.c - ${SDK_DIR}/drivers/lpsci/fsl_lpsci.c - ${SDK_DIR}/drivers/uart/fsl_uart.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c - ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_VARIANT}.c - ) - target_compile_definitions(${BOARD_TARGET} PUBLIC - ) - target_include_directories(${BOARD_TARGET} PUBLIC - ${CMSIS_DIR}/CMSIS/Core/Include - ${SDK_DIR}/devices/${MCU_VARIANT} - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers - ${SDK_DIR}/drivers/common - ${SDK_DIR}/drivers/gpio - ${SDK_DIR}/drivers/lpsci - ${SDK_DIR}/drivers/port - ${SDK_DIR}/drivers/smc - ${SDK_DIR}/drivers/uart - ) + if (TARGET ${BOARD_TARGET}) + return() + endif () - update_board(${BOARD_TARGET}) + add_library(${BOARD_TARGET} STATIC + ${SDK_DIR}/drivers/gpio/fsl_gpio.c + ${SDK_DIR}/drivers/lpsci/fsl_lpsci.c + ${SDK_DIR}/drivers/uart/fsl_uart.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c + ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_VARIANT}.c + ) + target_compile_definitions(${BOARD_TARGET} PUBLIC + ) + target_include_directories(${BOARD_TARGET} PUBLIC + ${CMSIS_DIR}/CMSIS/Core/Include + ${SDK_DIR}/devices/${MCU_VARIANT} + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers + ${SDK_DIR}/drivers/common + ${SDK_DIR}/drivers/gpio + ${SDK_DIR}/drivers/lpsci + ${SDK_DIR}/drivers/port + ${SDK_DIR}/drivers/smc + ${SDK_DIR}/drivers/uart + ) + update_board(${BOARD_TARGET}) - # LD_FILE and STARTUP_FILE can be defined in board.cmake + # LD_FILE and STARTUP_FILE can be defined in board.cmake + target_sources(${BOARD_TARGET} PUBLIC + ${STARTUP_FILE_${CMAKE_C_COMPILER_ID}} + ) - target_sources(${BOARD_TARGET} PUBLIC - ${STARTUP_FILE_${CMAKE_C_COMPILER_ID}} + if (CMAKE_C_COMPILER_ID STREQUAL "GNU") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--script=${LD_FILE_GNU}" + # nanolib + --specs=nosys.specs --specs=nano.specs + ) + elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--config=${LD_FILE_IAR}" ) - - if (CMAKE_C_COMPILER_ID STREQUAL "GNU") - target_link_options(${BOARD_TARGET} PUBLIC - "LINKER:--script=${LD_FILE_GNU}" - # nanolib - --specs=nosys.specs - --specs=nano.specs - ) - elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") - target_link_options(${BOARD_TARGET} PUBLIC - "LINKER:--config=${LD_FILE_IAR}" - ) - endif () endif () endfunction() diff --git a/hw/bsp/lpc17/boards/lpcxpresso1769/lpcxpresso1769.c b/hw/bsp/lpc17/boards/lpcxpresso1769/lpcxpresso1769.c index c7d655368..8c26b906f 100644 --- a/hw/bsp/lpc17/boards/lpcxpresso1769/lpcxpresso1769.c +++ b/hw/bsp/lpc17/boards/lpcxpresso1769/lpcxpresso1769.c @@ -37,7 +37,7 @@ void USB_IRQHandler(void) #endif #if CFG_TUH_ENABLED - tuh_int_handler(0); + tuh_int_handler(0, true); #endif } diff --git a/hw/bsp/lpc17/boards/mbed1768/mbed1768.c b/hw/bsp/lpc17/boards/mbed1768/mbed1768.c index b2c92d640..613dcb570 100644 --- a/hw/bsp/lpc17/boards/mbed1768/mbed1768.c +++ b/hw/bsp/lpc17/boards/mbed1768/mbed1768.c @@ -151,7 +151,7 @@ void USB_IRQHandler(void) #endif #if CFG_TUH_ENABLED - tuh_int_handler(0); + tuh_int_handler(0, true); #endif } diff --git a/hw/bsp/lpc18/family.c b/hw/bsp/lpc18/family.c index b11f4fe0e..e6abecb4b 100644 --- a/hw/bsp/lpc18/family.c +++ b/hw/bsp/lpc18/family.c @@ -43,25 +43,23 @@ //--------------------------------------------------------------------+ // USB Interrupt Handler //--------------------------------------------------------------------+ -void USB0_IRQHandler(void) -{ +void USB0_IRQHandler(void) { #if PORT_SUPPORT_DEVICE(0) - tud_int_handler(0); + tud_int_handler(0); #endif #if PORT_SUPPORT_HOST(0) - tuh_int_handler(0); + tuh_int_handler(0, true); #endif } -void USB1_IRQHandler(void) -{ +void USB1_IRQHandler(void) { #if PORT_SUPPORT_DEVICE(1) - tud_int_handler(1); + tud_int_handler(1); #endif #if PORT_SUPPORT_HOST(1) - tuh_int_handler(1); + tuh_int_handler(1, true); #endif } @@ -74,28 +72,26 @@ const uint32_t OscRateIn = 12000000; const uint32_t ExtRateIn = 0; // Invoked by startup code -void SystemInit(void) -{ +void SystemInit(void) { #ifdef __USE_LPCOPEN - extern void (* const g_pfnVectors[])(void); + extern void (*const g_pfnVectors[])(void); unsigned int *pSCB_VTOR = (unsigned int *) 0xE000ED08; - *pSCB_VTOR = (unsigned int) g_pfnVectors; + *pSCB_VTOR = (unsigned int) g_pfnVectors; #endif board_lpc18_pinmux(); - #ifdef TRACE_ETM +#ifdef TRACE_ETM // Trace clock is limited to 60MHz, limit CPU clock to 120MHz Chip_SetupCoreClock(CLKIN_CRYSTAL, 120000000UL, true); - #else +#else // CPU clock max to 180 Mhz Chip_SetupCoreClock(CLKIN_CRYSTAL, MAX_CLOCK_FREQ, true); - #endif +#endif } -void board_init(void) -{ +void board_init(void) { SystemCoreClockUpdate(); #if CFG_TUSB_OS == OPT_OS_NONE @@ -135,27 +131,22 @@ void board_init(void) // Board porting API //--------------------------------------------------------------------+ -void board_led_write(bool state) -{ +void board_led_write(bool state) { Chip_GPIO_SetPinState(LPC_GPIO_PORT, LED_PORT, LED_PIN, state); } -uint32_t board_button_read(void) -{ +uint32_t board_button_read(void) { // active low return Chip_GPIO_GetPinState(LPC_GPIO_PORT, BUTTON_PORT, BUTTON_PIN) ? 0 : 1; } -int board_uart_read(uint8_t* buf, int len) -{ +int board_uart_read(uint8_t *buf, int len) { return Chip_UART_Read(UART_DEV, buf, len); } -int board_uart_write(void const * buf, int len) -{ - uint8_t const* buf8 = (uint8_t const*) buf; - for(int i=0; iINTFLAG.reg = EIC_INTFLAG_EXTINT(1 << MAX3421_INTR_EIC_ID); // Call the TinyUSB interrupt handler - tuh_int_handler(1); + tuh_int_handler(1, true); } void tuh_max3421_int_api(uint8_t rhport, bool enabled) { diff --git a/hw/bsp/samd51/family.c b/hw/bsp/samd51/family.c index 2cf00c7af..268d60e48 100644 --- a/hw/bsp/samd51/family.c +++ b/hw/bsp/samd51/family.c @@ -296,7 +296,7 @@ void MAX3421_EIC_Handler(void) { EIC->INTFLAG.reg = EIC_INTFLAG_EXTINT(1 << MAX3421_INTR_EIC_ID); // Call the TinyUSB interrupt handler - tuh_int_handler(1); + tuh_int_handler(1, true); } void tuh_max3421_int_api(uint8_t rhport, bool enabled) { diff --git a/hw/bsp/stm32g4/family.cmake b/hw/bsp/stm32g4/family.cmake index 675a96c74..f8cabcbe5 100644 --- a/hw/bsp/stm32g4/family.cmake +++ b/hw/bsp/stm32g4/family.cmake @@ -26,50 +26,47 @@ set(FAMILY_MCUS STM32G4 CACHE INTERNAL "") #------------------------------------ # only need to be built ONCE for all examples function(add_board_target BOARD_TARGET) - if (NOT TARGET ${BOARD_TARGET}) - # Startup & Linker script - set(STARTUP_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/startup_${MCU_VARIANT}.s) - set(STARTUP_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/startup_${MCU_VARIANT}.s) - set(LD_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/linker/${MCU_VARIANT}_flash.icf) - - add_library(${BOARD_TARGET} STATIC - ${ST_CMSIS}/Source/Templates/system_${ST_PREFIX}.c - ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal.c - ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_cortex.c - ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_pwr_ex.c - ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc.c - ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc_ex.c - ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_gpio.c - ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_uart.c - ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_uart_ex.c - ${STARTUP_FILE_${CMAKE_C_COMPILER_ID}} - ) - target_include_directories(${BOARD_TARGET} PUBLIC - ${CMAKE_CURRENT_FUNCTION_LIST_DIR} - ${CMSIS_5}/CMSIS/Core/Include - ${ST_CMSIS}/Include - ${ST_HAL_DRIVER}/Inc - ) - target_compile_options(${BOARD_TARGET} PUBLIC + if (TARGET ${BOARD_TARGET}) + return() + endif () + + # Startup & Linker script + set(STARTUP_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/startup_${MCU_VARIANT}.s) + set(STARTUP_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/startup_${MCU_VARIANT}.s) + set(LD_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/linker/${MCU_VARIANT}_flash.icf) + + add_library(${BOARD_TARGET} STATIC + ${ST_CMSIS}/Source/Templates/system_${ST_PREFIX}.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_cortex.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_pwr_ex.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc_ex.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_gpio.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_uart.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_uart_ex.c + ${STARTUP_FILE_${CMAKE_C_COMPILER_ID}} + ) + target_include_directories(${BOARD_TARGET} PUBLIC + ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + ${CMSIS_5}/CMSIS/Core/Include + ${ST_CMSIS}/Include + ${ST_HAL_DRIVER}/Inc + ) + update_board(${BOARD_TARGET}) + + if (CMAKE_C_COMPILER_ID STREQUAL "GNU") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--script=${LD_FILE_GNU}" + -nostartfiles + # nanolib + --specs=nosys.specs + --specs=nano.specs ) - target_compile_definitions(${BOARD_TARGET} PUBLIC + elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--config=${LD_FILE_IAR}" ) - - update_board(${BOARD_TARGET}) - - if (CMAKE_C_COMPILER_ID STREQUAL "GNU") - target_link_options(${BOARD_TARGET} PUBLIC - "LINKER:--script=${LD_FILE_GNU}" - -nostartfiles - # nanolib - --specs=nosys.specs - --specs=nano.specs - ) - elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") - target_link_options(${BOARD_TARGET} PUBLIC - "LINKER:--config=${LD_FILE_IAR}" - ) - endif () endif () endfunction() diff --git a/hw/bsp/tm4c123/family.c b/hw/bsp/tm4c123/family.c index ad5ae505f..738bc3fa0 100644 --- a/hw/bsp/tm4c123/family.c +++ b/hw/bsp/tm4c123/family.c @@ -8,7 +8,7 @@ void USB0_Handler(void) { #if CFG_TUH_ENABLED - tuh_int_handler(0); + tuh_int_handler(0, true); #endif #if CFG_TUD_ENABLED diff --git a/src/common/tusb_common.h b/src/common/tusb_common.h index 6fffed11c..caeb5f2ef 100644 --- a/src/common/tusb_common.h +++ b/src/common/tusb_common.h @@ -75,8 +75,6 @@ #include "tusb_types.h" #include "tusb_debug.h" -#include "tusb_timeout.h" // TODO remove - //--------------------------------------------------------------------+ // Optional API implemented by application if needed // TODO move to a more ovious place/file diff --git a/src/common/tusb_timeout.h b/src/common/tusb_timeout.h deleted file mode 100644 index 533e67ab8..000000000 --- a/src/common/tusb_timeout.h +++ /dev/null @@ -1,80 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -/** \ingroup Group_Common Common Files - * \defgroup Group_TimeoutTimer timeout timer - * @{ */ - -#ifndef _TUSB_TIMEOUT_H_ -#define _TUSB_TIMEOUT_H_ - -#include -#include - -#ifdef __cplusplus -extern "C" { -#endif - -typedef struct { - uint32_t start; - uint32_t interval; -}tu_timeout_t; - -#if 0 - -extern uint32_t tusb_hal_millis(void); - -static inline void tu_timeout_set(tu_timeout_t* tt, uint32_t msec) -{ - tt->interval = msec; - tt->start = tusb_hal_millis(); -} - -static inline bool tu_timeout_expired(tu_timeout_t* tt) -{ - return ( tusb_hal_millis() - tt->start ) >= tt->interval; -} - -// For used with periodic event to prevent drift -static inline void tu_timeout_reset(tu_timeout_t* tt) -{ - tt->start += tt->interval; -} - -static inline void tu_timeout_restart(tu_timeout_t* tt) -{ - tt->start = tusb_hal_millis(); -} - -#endif - -#ifdef __cplusplus - } -#endif - -#endif /* _TUSB_TIMEOUT_H_ */ - -/** @} */ diff --git a/src/common/tusb_verify.h b/src/common/tusb_verify.h index 12355e8be..1b5f53dfc 100644 --- a/src/common/tusb_verify.h +++ b/src/common/tusb_verify.h @@ -56,12 +56,8 @@ * #define TU_VERIFY(cond) if(cond) return false; * #define TU_VERIFY(cond,ret) if(cond) return ret; * - * #define TU_VERIFY_HDLR(cond,handler) if(cond) {handler; return false;} - * #define TU_VERIFY_HDLR(cond,ret,handler) if(cond) {handler; return ret;} - * * #define TU_ASSERT(cond) if(cond) {_MESS_FAILED(); TU_BREAKPOINT(), return false;} * #define TU_ASSERT(cond,ret) if(cond) {_MESS_FAILED(); TU_BREAKPOINT(), return ret;} - * *------------------------------------------------------------------*/ #ifdef __cplusplus @@ -97,40 +93,23 @@ #define TU_BREAKPOINT() do {} while (0) #endif -/*------------------------------------------------------------------*/ -/* Macro Generator - *------------------------------------------------------------------*/ - // Helper to implement optional parameter for TU_VERIFY Macro family #define _GET_3RD_ARG(arg1, arg2, arg3, ...) arg3 -#define _GET_4TH_ARG(arg1, arg2, arg3, arg4, ...) arg4 - -/*------------- Generator for TU_VERIFY and TU_VERIFY_HDLR -------------*/ -#define TU_VERIFY_DEFINE(_cond, _handler, _ret) do \ -{ \ - if ( !(_cond) ) { _handler; return _ret; } \ -} while(0) /*------------------------------------------------------------------*/ /* TU_VERIFY * - TU_VERIFY_1ARGS : return false if failed * - TU_VERIFY_2ARGS : return provided value if failed *------------------------------------------------------------------*/ -#define TU_VERIFY_1ARGS(_cond) TU_VERIFY_DEFINE(_cond, , false) -#define TU_VERIFY_2ARGS(_cond, _ret) TU_VERIFY_DEFINE(_cond, , _ret) +#define TU_VERIFY_DEFINE(_cond, _ret) \ + do { \ + if ( !(_cond) ) { return _ret; } \ + } while(0) -#define TU_VERIFY(...) _GET_3RD_ARG(__VA_ARGS__, TU_VERIFY_2ARGS, TU_VERIFY_1ARGS, UNUSED)(__VA_ARGS__) +#define TU_VERIFY_1ARGS(_cond) TU_VERIFY_DEFINE(_cond, false) +#define TU_VERIFY_2ARGS(_cond, _ret) TU_VERIFY_DEFINE(_cond, _ret) - -/*------------------------------------------------------------------*/ -/* TU_VERIFY WITH HANDLER - * - TU_VERIFY_HDLR_2ARGS : execute handler, return false if failed - * - TU_VERIFY_HDLR_3ARGS : execute handler, return provided error if failed - *------------------------------------------------------------------*/ -#define TU_VERIFY_HDLR_2ARGS(_cond, _handler) TU_VERIFY_DEFINE(_cond, _handler, false) -#define TU_VERIFY_HDLR_3ARGS(_cond, _handler, _ret) TU_VERIFY_DEFINE(_cond, _handler, _ret) - -#define TU_VERIFY_HDLR(...) _GET_4TH_ARG(__VA_ARGS__, TU_VERIFY_HDLR_3ARGS, TU_VERIFY_HDLR_2ARGS,UNUSED)(__VA_ARGS__) +#define TU_VERIFY(...) _GET_3RD_ARG(__VA_ARGS__, TU_VERIFY_2ARGS, TU_VERIFY_1ARGS, _dummy)(__VA_ARGS__) /*------------------------------------------------------------------*/ /* ASSERT @@ -138,19 +117,20 @@ * - 1 arg : return false if failed * - 2 arg : return error if failed *------------------------------------------------------------------*/ -#define ASSERT_1ARGS(_cond) TU_VERIFY_DEFINE(_cond, _MESS_FAILED(); TU_BREAKPOINT(), false) -#define ASSERT_2ARGS(_cond, _ret) TU_VERIFY_DEFINE(_cond, _MESS_FAILED(); TU_BREAKPOINT(), _ret) +#define TU_ASSERT_DEFINE(_cond, _ret) \ + do { \ + if ( !(_cond) ) { _MESS_FAILED(); TU_BREAKPOINT(); return _ret; } \ + } while(0) + +#define TU_ASSERT_1ARGS(_cond) TU_ASSERT_DEFINE(_cond, false) +#define TU_ASSERT_2ARGS(_cond, _ret) TU_ASSERT_DEFINE(_cond, _ret) #ifndef TU_ASSERT -#define TU_ASSERT(...) _GET_3RD_ARG(__VA_ARGS__, ASSERT_2ARGS, ASSERT_1ARGS,UNUSED)(__VA_ARGS__) +#define TU_ASSERT(...) _GET_3RD_ARG(__VA_ARGS__, TU_ASSERT_2ARGS, TU_ASSERT_1ARGS, _dummy)(__VA_ARGS__) #endif -/*------------------------------------------------------------------*/ -/* ASSERT HDLR - *------------------------------------------------------------------*/ - #ifdef __cplusplus } #endif -#endif /* TUSB_VERIFY_H_ */ +#endif diff --git a/src/host/hcd.h b/src/host/hcd.h index e25b20ea3..2bde289df 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -131,7 +131,7 @@ bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) TU_AT bool hcd_init(uint8_t rhport); // Interrupt Handler -void hcd_int_handler(uint8_t rhport); +void hcd_int_handler(uint8_t rhport, bool in_isr); // Enable USB interrupt void hcd_int_enable (uint8_t rhport); diff --git a/src/host/usbh.h b/src/host/usbh.h index 684e8240e..770d70dfe 100644 --- a/src/host/usbh.h +++ b/src/host/usbh.h @@ -124,11 +124,16 @@ void tuh_task(void) { bool tuh_task_event_ready(void); #ifndef _TUSB_HCD_H_ -extern void hcd_int_handler(uint8_t rhport); +extern void hcd_int_handler(uint8_t rhport, bool in_isr); #endif -// Interrupt handler, name alias to HCD -#define tuh_int_handler hcd_int_handler +// Interrupt handler alias to HCD with in_isr as optional parameter +// - tuh_int_handler(rhport) --> hcd_int_handler(rhport, true) +// - tuh_int_handler(rhport, in_isr) --> hcd_int_handler(rhport, in_isr) +// Note: this is similar to TU_VERIFY(), _GET_3RD_ARG() is defined in tusb_verify.h +#define _tuh_int_handler_1arg(_rhport) hcd_int_handler(_rhport, true) +#define _tuh_int_hanlder_2arg(_rhport, _in_isr) hcd_int_handler(_rhport, _in_isr) +#define tuh_int_handler(...) _GET_3RD_ARG(__VA_ARGS__, _tuh_int_hanlder_2arg, _tuh_int_handler_1arg, _dummy)(__VA_ARGS__) // Check if roothub port is initialized and active as a host bool tuh_rhport_is_active(uint8_t rhport); diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 238b518a0..d013d6179 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -863,7 +863,8 @@ void print_hirq(uint8_t hirq) { #endif // Interrupt Handler -void hcd_int_handler(uint8_t rhport) { +void hcd_int_handler(uint8_t rhport, bool in_isr) { + (void) in_isr; uint8_t hirq = reg_read(rhport, HIRQ_ADDR, true) & _hcd_data.hien; if (!hirq) return; // print_hirq(hirq); diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index c93c33fc0..572b9826c 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -656,8 +656,8 @@ void process_period_xfer_isr(uint8_t rhport, uint32_t interval_ms) } //------------- Host Controller Driver's Interrupt Handler -------------// -void hcd_int_handler(uint8_t rhport) -{ +void hcd_int_handler(uint8_t rhport, bool in_isr) { + (void) in_isr; ehci_registers_t* regs = ehci_data.regs; uint32_t const int_status = regs->status; diff --git a/src/portable/mentor/musb/hcd_musb.c b/src/portable/mentor/musb/hcd_musb.c index 02090df85..5312c2812 100644 --- a/src/portable/mentor/musb/hcd_musb.c +++ b/src/portable/mentor/musb/hcd_musb.c @@ -847,8 +847,10 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { /*------------------------------------------------------------------- * ISR *-------------------------------------------------------------------*/ -void hcd_int_handler(uint8_t rhport) +void hcd_int_handler(uint8_t rhport, bool in_isr) { + (void) in_isr; + uint_fast8_t is, txis, rxis; is = USB0->IS; /* read and clear interrupt status */ diff --git a/src/portable/nxp/khci/hcd_khci.c b/src/portable/nxp/khci/hcd_khci.c index 55327e02d..57684b259 100644 --- a/src/portable/nxp/khci/hcd_khci.c +++ b/src/portable/nxp/khci/hcd_khci.c @@ -447,6 +447,10 @@ void hcd_port_reset(uint8_t rhport) _hcd.need_reset = false; } +void hcd_port_reset_end(uint8_t rhport) { + (void) rhport; +} + tusb_speed_t hcd_port_speed_get(uint8_t rhport) { (void)rhport; @@ -583,8 +587,9 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { /*--------------------------------------------------------------------+ * ISR *--------------------------------------------------------------------+*/ -void hcd_int_handler(uint8_t rhport) +void hcd_int_handler(uint8_t rhport, bool in_isr) { + (void) in_isr; uint32_t is = KHCI->ISTAT; uint32_t msk = KHCI->INTEN; diff --git a/src/portable/ohci/ohci.c b/src/portable/ohci/ohci.c index 413e72037..f978b0965 100644 --- a/src/portable/ohci/ohci.c +++ b/src/portable/ohci/ohci.c @@ -667,8 +667,9 @@ static void done_queue_isr(uint8_t hostid) } } -void hcd_int_handler(uint8_t hostid) -{ +void hcd_int_handler(uint8_t hostid, bool in_isr) { + (void) in_isr; + uint32_t const int_en = OHCI_REG->interrupt_enable; uint32_t const int_status = OHCI_REG->interrupt_status & int_en; diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 21dc3f67d..4ed6d36bb 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -252,9 +252,9 @@ static void __tusb_irq_path_func(hcd_rp2040_irq)(void) } } -void __tusb_irq_path_func(hcd_int_handler)(uint8_t rhport) -{ +void __tusb_irq_path_func(hcd_int_handler)(uint8_t rhport, bool in_isr) { (void) rhport; + (void) in_isr; hcd_rp2040_irq(); } diff --git a/src/portable/renesas/rusb2/hcd_rusb2.c b/src/portable/renesas/rusb2/hcd_rusb2.c index 790cd6b32..bf95be707 100644 --- a/src/portable/renesas/rusb2/hcd_rusb2.c +++ b/src/portable/renesas/rusb2/hcd_rusb2.c @@ -771,8 +771,9 @@ bool hcd_edpt_clear_stall(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr) { //--------------------------------------------------------------------+ // ISR //--------------------------------------------------------------------+ -void hcd_int_handler(uint8_t rhport) -{ +void hcd_int_handler(uint8_t rhport, bool in_isr) { + (void) in_isr; + rusb2_reg_t* rusb = RUSB2_REG(rhport); unsigned is0 = rusb->INTSTS0; unsigned is1 = rusb->INTSTS1; diff --git a/src/portable/template/hcd_template.c b/src/portable/template/hcd_template.c index 3e3b91558..b073d6057 100644 --- a/src/portable/template/hcd_template.c +++ b/src/portable/template/hcd_template.c @@ -51,8 +51,9 @@ bool hcd_init(uint8_t rhport) { } // Interrupt Handler -void hcd_int_handler(uint8_t rhport) { +void hcd_int_handler(uint8_t rhport, bool in_isr) { (void) rhport; + (void) in_isr; } // Enable USB interrupt diff --git a/src/tusb.h b/src/tusb.h index d6534ca28..c9d56d3c3 100644 --- a/src/tusb.h +++ b/src/tusb.h @@ -66,7 +66,7 @@ #endif #else #ifndef tuh_int_handler - #define tuh_int_handler(_x) + #define tuh_int_handler(...) #endif #endif @@ -123,7 +123,7 @@ #endif #else #ifndef tud_int_handler - #define tud_int_handler(_x) + #define tud_int_handler(...) #endif #endif -- cgit v1.3.1 From 6b8933cfe838b369c58d4fc9ced8aa5c9382a6d6 Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 28 Sep 2023 12:55:59 +0700 Subject: fix build with new freertos host example --- examples/device/cdc_msc_freertos/Makefile | 2 - examples/host/bare_api/Makefile | 10 - examples/host/cdc_msc_hid/Makefile | 10 - examples/host/cdc_msc_hid_freertos/Makefile | 18 +- .../src/FreeRTOSConfig/FreeRTOSConfig.h | 215 +++++++++++++++++++++ examples/host/hid_controller/Makefile | 10 - examples/host/msc_file_explorer/Makefile | 10 - hw/bsp/lpc17/family.mk | 4 +- src/portable/analog/max3421/hcd_max3421.c | 4 +- src/tinyusb.mk | 7 + 10 files changed, 237 insertions(+), 53 deletions(-) create mode 100644 examples/host/cdc_msc_hid_freertos/src/FreeRTOSConfig/FreeRTOSConfig.h (limited to 'src/portable') diff --git a/examples/device/cdc_msc_freertos/Makefile b/examples/device/cdc_msc_freertos/Makefile index 3ac62a79c..84c833fb5 100644 --- a/examples/device/cdc_msc_freertos/Makefile +++ b/examples/device/cdc_msc_freertos/Makefile @@ -1,5 +1,3 @@ -DEPS_SUBMODULES += lib/FreeRTOS-Kernel - include ../../make.mk FREERTOS_SRC = lib/FreeRTOS-Kernel diff --git a/examples/host/bare_api/Makefile b/examples/host/bare_api/Makefile index 058307c40..161f8c774 100644 --- a/examples/host/bare_api/Makefile +++ b/examples/host/bare_api/Makefile @@ -10,14 +10,4 @@ EXAMPLE_SOURCE += \ SRC_C += $(addprefix $(CURRENT_PATH)/, $(EXAMPLE_SOURCE)) -# TinyUSB Host Stack source -SRC_C += \ - src/class/cdc/cdc_host.c \ - src/class/hid/hid_host.c \ - src/class/msc/msc_host.c \ - src/host/hub.c \ - src/host/usbh.c \ - src/portable/ohci/ohci.c \ - src/portable/nxp/lpc17_40/hcd_lpc17_40.c - include ../../rules.mk diff --git a/examples/host/cdc_msc_hid/Makefile b/examples/host/cdc_msc_hid/Makefile index 7c16b39d3..15b8a5b31 100644 --- a/examples/host/cdc_msc_hid/Makefile +++ b/examples/host/cdc_msc_hid/Makefile @@ -13,14 +13,4 @@ EXAMPLE_SOURCE = \ SRC_C += $(addprefix $(CURRENT_PATH)/, $(EXAMPLE_SOURCE)) -# TinyUSB Host Stack source -SRC_C += \ - src/class/cdc/cdc_host.c \ - src/class/hid/hid_host.c \ - src/class/msc/msc_host.c \ - src/host/hub.c \ - src/host/usbh.c \ - src/portable/ohci/ohci.c \ - src/portable/nxp/lpc17_40/hcd_lpc17_40.c - include ../../rules.mk diff --git a/examples/host/cdc_msc_hid_freertos/Makefile b/examples/host/cdc_msc_hid_freertos/Makefile index 67bb6da55..a9670b4f2 100644 --- a/examples/host/cdc_msc_hid_freertos/Makefile +++ b/examples/host/cdc_msc_hid_freertos/Makefile @@ -5,6 +5,7 @@ FREERTOS_PORTABLE_PATH= $(FREERTOS_SRC)/portable/$(if $(USE_IAR),IAR,GCC) INC += \ src \ + src/FreeRTOSConfig \ $(TOP)/hw \ $(TOP)/$(FREERTOS_SRC)/include \ $(TOP)/$(FREERTOS_PORTABLE_SRC) \ @@ -19,14 +20,15 @@ EXAMPLE_SOURCE = \ SRC_C += $(addprefix $(CURRENT_PATH)/, $(EXAMPLE_SOURCE)) -# TinyUSB Host Stack source +# FreeRTOS source, all files in port folder SRC_C += \ - src/class/cdc/cdc_host.c \ - src/class/hid/hid_host.c \ - src/class/msc/msc_host.c \ - src/host/hub.c \ - src/host/usbh.c \ - src/portable/ohci/ohci.c \ - src/portable/nxp/lpc17_40/hcd_lpc17_40.c + $(FREERTOS_SRC)/list.c \ + $(FREERTOS_SRC)/queue.c \ + $(FREERTOS_SRC)/tasks.c \ + $(FREERTOS_SRC)/timers.c \ + $(subst $(TOP)/,,$(wildcard $(TOP)/$(FREERTOS_PORTABLE_SRC)/*.c)) + +SRC_S += \ + $(subst $(TOP)/,,$(wildcard $(TOP)/$(FREERTOS_PORTABLE_SRC)/*.s)) include ../../rules.mk diff --git a/examples/host/cdc_msc_hid_freertos/src/FreeRTOSConfig/FreeRTOSConfig.h b/examples/host/cdc_msc_hid_freertos/src/FreeRTOSConfig/FreeRTOSConfig.h new file mode 100644 index 000000000..a1fc8bb09 --- /dev/null +++ b/examples/host/cdc_msc_hid_freertos/src/FreeRTOSConfig/FreeRTOSConfig.h @@ -0,0 +1,215 @@ +/* + * FreeRTOS Kernel V10.0.0 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. If you wish to use our Amazon + * FreeRTOS name, please do so in a fair use way that does not cause confusion. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + + +#ifndef FREERTOS_CONFIG_H +#define FREERTOS_CONFIG_H + +/*----------------------------------------------------------- + * Application specific definitions. + * + * These definitions should be adjusted for your particular hardware and + * application requirements. + * + * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE + * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. + * + * See http://www.freertos.org/a00110.html. + *----------------------------------------------------------*/ + +// skip if included from IAR assembler +#ifndef __IASMARM__ + +// Include MCU header +#include "bsp/board_mcu.h" + +#if CFG_TUSB_MCU == OPT_MCU_ESP32S2 || CFG_TUSB_MCU == OPT_MCU_ESP32S3 + #error "ESP32-Sx should use IDF's FreeRTOSConfig.h" +#endif + +#ifdef __GNUC__ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wredundant-decls" +#endif + +// TODO fix later +// FIXME cause redundant-decls warnings +#if CFG_TUSB_MCU == OPT_MCU_MM32F327X + extern u32 SystemCoreClock; +#else + extern uint32_t SystemCoreClock; +#endif + +#ifdef __GNUC__ +#pragma GCC diagnostic pop +#endif + +#endif + +/* Cortex M23/M33 port configuration. */ +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE ( 1024 ) + +#define configUSE_PREEMPTION 1 +#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 +#define configCPU_CLOCK_HZ SystemCoreClock +#define configTICK_RATE_HZ ( 1000 ) +#define configMAX_PRIORITIES ( 5 ) +#define configMINIMAL_STACK_SIZE ( 128 ) +#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) +#define configMAX_TASK_NAME_LEN 16 +#define configUSE_16_BIT_TICKS 0 +#define configIDLE_SHOULD_YIELD 1 +#define configUSE_MUTEXES 1 +#define configUSE_RECURSIVE_MUTEXES 1 +#define configUSE_COUNTING_SEMAPHORES 1 +#define configQUEUE_REGISTRY_SIZE 4 +#define configUSE_QUEUE_SETS 0 +#define configUSE_TIME_SLICING 0 +#define configUSE_NEWLIB_REENTRANT 0 +#define configENABLE_BACKWARD_COMPATIBILITY 1 +#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 + +#define configSUPPORT_STATIC_ALLOCATION 1 +#define configSUPPORT_DYNAMIC_ALLOCATION 0 + +/* Hook function related definitions. */ +#define configUSE_IDLE_HOOK 0 +#define configUSE_TICK_HOOK 0 +#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning +#define configCHECK_FOR_STACK_OVERFLOW 2 + +/* Run time and task stats gathering related definitions. */ +#define configGENERATE_RUN_TIME_STATS 0 +#define configUSE_TRACE_FACILITY 1 // legacy trace +#define configUSE_STATS_FORMATTING_FUNCTIONS 0 + +/* Co-routine definitions. */ +#define configUSE_CO_ROUTINES 0 +#define configMAX_CO_ROUTINE_PRIORITIES 2 + +/* Software timer related definitions. */ +#define configUSE_TIMERS 1 +#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) +#define configTIMER_QUEUE_LENGTH 32 +#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE + +/* Optional functions - most linkers will remove unused functions anyway. */ +#define INCLUDE_vTaskPrioritySet 0 +#define INCLUDE_uxTaskPriorityGet 0 +#define INCLUDE_vTaskDelete 0 +#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY +#define INCLUDE_xResumeFromISR 0 +#define INCLUDE_vTaskDelayUntil 1 +#define INCLUDE_vTaskDelay 1 +#define INCLUDE_xTaskGetSchedulerState 0 +#define INCLUDE_xTaskGetCurrentTaskHandle 0 +#define INCLUDE_uxTaskGetStackHighWaterMark 0 +#define INCLUDE_xTaskGetIdleTaskHandle 0 +#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 +#define INCLUDE_pcTaskGetTaskName 0 +#define INCLUDE_eTaskGetState 0 +#define INCLUDE_xEventGroupSetBitFromISR 0 +#define INCLUDE_xTimerPendFunctionCall 0 + +/* Define to trap errors during development. */ +// Halt CPU (breakpoint) when hitting error, only apply for Cortex M3, M4, M7 +#if defined(__ARM_ARCH_7M__) || defined (__ARM_ARCH_7EM__) + #define configASSERT(_exp) \ + do {\ + if ( !(_exp) ) { \ + volatile uint32_t* ARM_CM_DHCSR = ((volatile uint32_t*) 0xE000EDF0UL); /* Cortex M CoreDebug->DHCSR */ \ + if ( (*ARM_CM_DHCSR) & 1UL ) { /* Only halt mcu if debugger is attached */ \ + taskDISABLE_INTERRUPTS(); \ + __asm("BKPT #0\n"); \ + }\ + }\ + } while(0) +#else + #define configASSERT( x ) +#endif + +#ifdef __RX__ +/* Renesas RX series */ +#define vSoftwareInterruptISR INT_Excep_ICU_SWINT +#define vTickISR INT_Excep_CMT0_CMI0 +#define configPERIPHERAL_CLOCK_HZ (configCPU_CLOCK_HZ/2) +#define configKERNEL_INTERRUPT_PRIORITY 1 +#define configMAX_SYSCALL_INTERRUPT_PRIORITY 4 + +#else + +/* FreeRTOS hooks to NVIC vectors */ +#define xPortPendSVHandler PendSV_Handler +#define xPortSysTickHandler SysTick_Handler +#define vPortSVCHandler SVC_Handler + +//--------------------------------------------------------------------+ +// Interrupt nesting behavior configuration. +//--------------------------------------------------------------------+ +#if defined(__NVIC_PRIO_BITS) + // For Cortex-M specific: __NVIC_PRIO_BITS is defined in core_cmx.h + #define configPRIO_BITS __NVIC_PRIO_BITS + +#elif defined(__ECLIC_INTCTLBITS) + // RISC-V Bumblebee core from nuclei + #define configPRIO_BITS __ECLIC_INTCTLBITS + +#elif defined(__IASMARM__) + // FIXME: IAR Assembler cannot include mcu header directly to get __NVIC_PRIO_BITS. + // Therefore we will hard coded it to minimum value of 2 to get pass ci build. + // IAR user must update this to correct value of the target MCU + #message "configPRIO_BITS is hard coded to 2 to pass IAR build only. User should update it per MCU" + #define configPRIO_BITS 2 + +#else + #error "FreeRTOS configPRIO_BITS to be defined" +#endif + +/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1< Date: Wed, 4 Oct 2023 18:00:32 +0700 Subject: change tuh_max3421_spi_xfer_api() signature tested working with sam d21 and d51, not tested with nrf52, seem not working with esp32 --- hw/bsp/espressif/boards/family.c | 39 +++++++++++++++++++------------ hw/bsp/nrf/family.c | 20 ++++++++++------ hw/bsp/samd21/family.c | 27 +++++++++++---------- hw/bsp/samd51/family.c | 35 +++++++++++++++------------ src/portable/analog/max3421/hcd_max3421.c | 27 ++++++++++++--------- 5 files changed, 88 insertions(+), 60 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/espressif/boards/family.c b/hw/bsp/espressif/boards/family.c index c6a592627..912ca5f35 100644 --- a/hw/bsp/espressif/boards/family.c +++ b/hw/bsp/espressif/boards/family.c @@ -38,7 +38,9 @@ #if ESP_IDF_VERSION_MAJOR > 4 #include "esp_private/periph_ctrl.h" #else + #include "driver/periph_ctrl.h" + #endif // Note; current code use UART0 can cause device to reset while monitoring @@ -46,16 +48,21 @@ #define UART_ID UART_NUM_0 #ifdef NEOPIXEL_PIN + #include "led_strip.h" -static led_strip_t *strip; + +static led_strip_t* strip; #endif #if CFG_TUH_ENABLED && CFG_TUH_MAX3421 + #include "driver/spi_master.h" + static void max3421_init(void); + #endif -static void configure_pins(usb_hal_context_t *usb); +static void configure_pins(usb_hal_context_t* usb); //--------------------------------------------------------------------+ // Implementation @@ -115,11 +122,11 @@ void board_init(void) { #endif } -static void configure_pins(usb_hal_context_t *usb) { +static void configure_pins(usb_hal_context_t* usb) { /* usb_periph_iopins currently configures USB_OTG as USB Device. * Introduce additional parameters in usb_hal_context_t when adding support * for USB Host. */ - for (const usb_iopin_dsc_t *iopin = usb_periph_iopins; iopin->pin != -1; ++iopin) { + for (const usb_iopin_dsc_t* iopin = usb_periph_iopins; iopin->pin != -1; ++iopin) { if ((usb->use_external_phy) || (iopin->ext_phy_only == 0)) { esp_rom_gpio_pad_select_gpio(iopin->pin); if (iopin->is_output) { @@ -160,7 +167,7 @@ uint32_t board_button_read(void) { } // Get characters from UART -int board_uart_read(uint8_t *buf, int len) { +int board_uart_read(uint8_t* buf, int len) { #if USE_UART return uart_read_bytes(UART_ID, buf, len, 0); #else @@ -169,7 +176,7 @@ int board_uart_read(uint8_t *buf, int len) { } // Send characters to UART -int board_uart_write(void const *buf, int len) { +int board_uart_write(void const* buf, int len) { (void) buf; (void) len; return 0; @@ -216,7 +223,7 @@ static void max3421_init(void) { gpio_set_level(MAX3421_CS_PIN, 1); // SPI - spi_bus_config_t buscfg={ + spi_bus_config_t buscfg = { .miso_io_num = MAX3421_MISO_PIN, .mosi_io_num = MAX3421_MOSI_PIN, .sclk_io_num = MAX3421_SCK_PIN, @@ -228,7 +235,7 @@ static void max3421_init(void) { .data7_io_num = -1, .max_transfer_sz = 1024 }; - ESP_ERROR_CHECK( spi_bus_initialize(MAX3421_SPI_HOST, &buscfg, SPI_DMA_CH_AUTO) ); + ESP_ERROR_CHECK(spi_bus_initialize(MAX3421_SPI_HOST, &buscfg, SPI_DMA_CH_AUTO)); spi_device_interface_config_t max3421_cfg = { .mode = 0, @@ -236,7 +243,7 @@ static void max3421_init(void) { .spics_io_num = -1, // manual control CS .queue_size = 1 }; - ESP_ERROR_CHECK( spi_bus_add_device(MAX3421_SPI_HOST, &max3421_cfg, &max3421_spi) ); + ESP_ERROR_CHECK(spi_bus_add_device(MAX3421_SPI_HOST, &max3421_cfg, &max3421_spi)); // debug gpio_set_direction(13, GPIO_MODE_OUTPUT); @@ -244,7 +251,7 @@ static void max3421_init(void) { // Interrupt pin max3421_intr_sem = xSemaphoreCreateBinary(); - xTaskCreate(max3421_intr_task, "max3421 intr", 2048, NULL, configMAX_PRIORITIES-2, NULL); + xTaskCreate(max3421_intr_task, "max3421 intr", 2048, NULL, configMAX_PRIORITIES - 2, NULL); gpio_set_direction(MAX3421_INTR_PIN, GPIO_MODE_INPUT); gpio_set_intr_type(MAX3421_INTR_PIN, GPIO_INTR_NEGEDGE); @@ -267,18 +274,20 @@ void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { gpio_set_level(MAX3421_CS_PIN, active ? 0 : 1); } -bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_len, uint8_t *rx_buf, size_t rx_len) { +bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const* tx_buf, uint8_t* rx_buf, size_t xfer_bytes) { (void) rhport; - if (tx_len == 0) { + if (tx_buf == NULL) { // fifo read, transmit rx_buf as dummy tx_buf = rx_buf; - tx_len = rx_len; } + // length in bits + size_t const len_bits = xfer_bytes << 3; + spi_transaction_t xact = { - .length = tx_len << 3, // length in bits - .rxlength = rx_len << 3, // length in bits + .length = len_bits, + .rxlength = rx_buf ? len_bits : 0, .tx_buffer = tx_buf, .rx_buffer = rx_buf }; diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 631f53fcd..c431389f3 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -95,7 +95,9 @@ TU_ATTR_UNUSED static void power_event_handler(nrfx_power_usb_evt_t event) { //------------- Host using MAX2341E -------------// #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 + static void max3421_init(void); + static nrfx_spim_t _spi = NRFX_SPIM_INSTANCE(1); #endif @@ -203,15 +205,15 @@ uint32_t board_button_read(void) { return BUTTON_STATE_ACTIVE == nrf_gpio_pin_read(BUTTON_PIN); } -int board_uart_read(uint8_t *buf, int len) { +int board_uart_read(uint8_t* buf, int len) { (void) buf; (void) len; return 0; // return NRFX_SUCCESS == nrfx_uart_rx(&_uart_id, buf, (size_t) len) ? len : 0; } -int board_uart_write(void const *buf, int len) { - return (NRFX_SUCCESS == nrfx_uarte_tx(&_uart_id, (uint8_t const *) buf, (size_t) len)) ? len : 0; +int board_uart_write(void const* buf, int len) { + return (NRFX_SUCCESS == nrfx_uarte_tx(&_uart_id, (uint8_t const*) buf, (size_t) len)) ? len : 0; } #if CFG_TUSB_OS == OPT_OS_NONE @@ -323,6 +325,7 @@ static void max3421_init(void) { nrfx_gpiote_trigger_enable(MAX3421_INTR_PIN, true); } +// API to enable/disable MAX3421 INTR pin interrupt void tuh_max3421_int_api(uint8_t rhport, bool enabled) { (void) rhport; @@ -335,22 +338,25 @@ void tuh_max3421_int_api(uint8_t rhport, bool enabled) { } } +// API to control MAX3421 SPI CS void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { (void) rhport; nrf_gpio_pin_write(MAX3421_CS_PIN, active ? 0 : 1); } -bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_len, uint8_t *rx_buf, size_t rx_len) { +// API to transfer data with MAX3421 SPI +// Either tx_buf or rx_buf can be NULL, which means transfer is write or read only +bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const* tx_buf, uint8_t* rx_buf, size_t xfer_bytes) { (void) rhport; nrfx_spim_xfer_desc_t xfer = { .p_tx_buffer = tx_buf, - .tx_length = tx_len, + .tx_length = tx_buf ? xfer_bytes : 0, .p_rx_buffer = rx_buf, - .rx_length = rx_len, + .rx_length = rx_buf ? xfer_bytes : 0, }; - return (nrfx_spim_xfer(&_spi, &xfer, 0) == NRFX_SUCCESS); + return nrfx_spim_xfer(&_spi, &xfer, 0) == NRFX_SUCCESS; } #endif diff --git a/hw/bsp/samd21/family.c b/hw/bsp/samd21/family.c index b9365fc3f..ccb2c99b1 100644 --- a/hw/bsp/samd21/family.c +++ b/hw/bsp/samd21/family.c @@ -72,6 +72,7 @@ static void uart_init(void); #define MAX3421_SERCOM TU_XSTRCAT(SERCOM, MAX3421_SERCOM_ID) static void max3421_init(void); + #endif void board_init(void) { @@ -237,13 +238,13 @@ int board_uart_write(void const * buf, int len) static void uart_init(void) { } -int board_uart_read(uint8_t *buf, int len) { +int board_uart_read(uint8_t* buf, int len) { (void) buf; (void) len; return 0; } -int board_uart_write(void const *buf, int len) { +int board_uart_write(void const* buf, int len) { (void) buf; (void) len; return 0; @@ -261,6 +262,7 @@ void SysTick_Handler(void) { uint32_t board_millis(void) { return system_ticks; } + #endif //--------------------------------------------------------------------+ @@ -278,8 +280,8 @@ static void max3421_init(void) { // Configure GCLK for SERCOM // GCLK->CLKCTRL.reg = GCLK_CLKCTRL_ID_SERCOM4_CORE | GCLK_CLKCTRL_GEN_GCLK0 | GCLK_CLKCTRL_CLKEN; - GCLK->CLKCTRL.reg = GCLK_CLKCTRL_ID(GCLK_CLKCTRL_ID_SERCOM0_CORE_Val+MAX3421_SERCOM_ID) | - GCLK_CLKCTRL_GEN_GCLK0 | GCLK_CLKCTRL_CLKEN; + GCLK->CLKCTRL.reg = GCLK_CLKCTRL_ID(GCLK_CLKCTRL_ID_SERCOM0_CORE_Val + MAX3421_SERCOM_ID) | + GCLK_CLKCTRL_GEN_GCLK0 | GCLK_CLKCTRL_CLKEN; while (GCLK->STATUS.bit.SYNCBUSY); Sercom* sercom = MAX3421_SERCOM; @@ -293,7 +295,7 @@ static void max3421_init(void) { // Set up SPI in master mode, MSB first, SPI mode 0 sercom->SPI.CTRLA.reg = SERCOM_SPI_CTRLA_DOPO(MAX3421_TX_PAD) | SERCOM_SPI_CTRLA_DIPO(MAX3421_RX_PAD) | - SERCOM_SPI_CTRLA_MODE(3); + SERCOM_SPI_CTRLA_MODE(3); sercom->SPI.CTRLB.reg = SERCOM_SPI_CTRLB_CHSIZE(0) | SERCOM_SPI_CTRLB_RXEN; while (sercom->SPI.SYNCBUSY.bit.CTRLB == 1); @@ -366,6 +368,7 @@ void EIC_Handler(void) { tuh_int_handler(1, true); } +// API to enable/disable MAX3421 INTR pin interrupt void tuh_max3421_int_api(uint8_t rhport, bool enabled) { (void) rhport; @@ -376,24 +379,26 @@ void tuh_max3421_int_api(uint8_t rhport, bool enabled) { } } +// API to control MAX3421 SPI CS void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { (void) rhport; gpio_set_pin_level(MAX3421_CS_PIN, active ? 0 : 1); } -bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_len, uint8_t *rx_buf, size_t rx_len) { +// API to transfer data with MAX3421 SPI +// Either tx_buf or rx_buf can be NULL, which means transfer is write or read only +bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const* tx_buf, uint8_t* rx_buf, size_t xfer_bytes) { (void) rhport; Sercom* sercom = MAX3421_SERCOM; - size_t count = 0; - while (count < tx_len || count < rx_len) { + for (size_t count = 0; count < xfer_bytes; count++) { // Wait for the transmit buffer to be empty while (!sercom->SPI.INTFLAG.bit.DRE); // Write data to be transmitted uint8_t data = 0x00; - if (count < tx_len) { + if (tx_buf) { data = tx_buf[count]; } @@ -404,11 +409,9 @@ bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_l // Read received data data = (uint8_t) sercom->SPI.DATA.reg; - if (count < rx_len) { + if (rx_buf) { rx_buf[count] = data; } - - count++; } // wait for bus idle and clear flags diff --git a/hw/bsp/samd51/family.c b/hw/bsp/samd51/family.c index 4d43c7745..bca18e1a2 100644 --- a/hw/bsp/samd51/family.c +++ b/hw/bsp/samd51/family.c @@ -81,6 +81,7 @@ void USB_3_Handler(void) { #define MAX3421_EIC_Handler TU_XSTRCAT3(EIC_, MAX3421_INTR_EIC_ID, _Handler) static void max3421_init(void); + #endif void board_init(void) { @@ -153,13 +154,13 @@ uint32_t board_button_read(void) { return gpio_get_pin_level(BUTTON_PIN) ? 0 : 1; } -int board_uart_read(uint8_t *buf, int len) { +int board_uart_read(uint8_t* buf, int len) { (void) buf; (void) len; return 0; } -int board_uart_write(void const *buf, int len) { +int board_uart_write(void const* buf, int len) { (void) buf; (void) len; return 0; @@ -175,6 +176,7 @@ void SysTick_Handler(void) { uint32_t board_millis(void) { return system_ticks; } + #endif //--------------------------------------------------------------------+ @@ -189,7 +191,7 @@ static void max3421_init(void) { uint32_t const baudrate = 12000000u; struct { - volatile uint32_t *mck_apb; + volatile uint32_t* mck_apb; uint32_t mask; uint8_t gclk_id_core; uint8_t gclk_id_slow; @@ -214,8 +216,10 @@ static void max3421_init(void) { *sercom_clock[MAX3421_SERCOM_ID].mck_apb |= sercom_clock[MAX3421_SERCOM_ID].mask; // Configure GCLK for SERCOM - GCLK->PCHCTRL[sercom_clock[MAX3421_SERCOM_ID].gclk_id_core].reg = GCLK_PCHCTRL_GEN_GCLK0_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); - GCLK->PCHCTRL[sercom_clock[MAX3421_SERCOM_ID].gclk_id_slow].reg = GCLK_PCHCTRL_GEN_GCLK3_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); + GCLK->PCHCTRL[sercom_clock[MAX3421_SERCOM_ID].gclk_id_core].reg = + GCLK_PCHCTRL_GEN_GCLK0_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); + GCLK->PCHCTRL[sercom_clock[MAX3421_SERCOM_ID].gclk_id_slow].reg = + GCLK_PCHCTRL_GEN_GCLK3_Val | (1 << GCLK_PCHCTRL_CHEN_Pos); // Disable the SPI module sercom->SPI.CTRLA.bit.ENABLE = 0; @@ -226,7 +230,7 @@ static void max3421_init(void) { // Set up SPI in master mode, MSB first, SPI mode 0 sercom->SPI.CTRLA.reg = SERCOM_SPI_CTRLA_DOPO(MAX3421_TX_PAD) | SERCOM_SPI_CTRLA_DIPO(MAX3421_RX_PAD) | - SERCOM_SPI_CTRLA_MODE(3); + SERCOM_SPI_CTRLA_MODE(3); sercom->SPI.CTRLB.reg = SERCOM_SPI_CTRLB_CHSIZE(0) | SERCOM_SPI_CTRLB_RXEN; while (sercom->SPI.SYNCBUSY.bit.CTRLB == 1); @@ -278,9 +282,9 @@ static void max3421_init(void) { while (EIC->SYNCBUSY.bit.ENABLE); // Configure EIC to trigger on falling edge - volatile uint32_t * eic_config; + volatile uint32_t* eic_config; uint8_t sense_shift; - if ( MAX3421_INTR_EIC_ID < 8 ) { + if (MAX3421_INTR_EIC_ID < 8) { eic_config = &EIC->CONFIG[0].reg; sense_shift = MAX3421_INTR_EIC_ID * 4; } else { @@ -312,6 +316,7 @@ void MAX3421_EIC_Handler(void) { tuh_int_handler(1, true); } +// API to enable/disable MAX3421 INTR pin interrupt void tuh_max3421_int_api(uint8_t rhport, bool enabled) { (void) rhport; @@ -323,24 +328,26 @@ void tuh_max3421_int_api(uint8_t rhport, bool enabled) { } } +// API to control MAX3421 SPI CS void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { (void) rhport; gpio_set_pin_level(MAX3421_CS_PIN, active ? 0 : 1); } -bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_len, uint8_t *rx_buf, size_t rx_len) { +// API to transfer data with MAX3421 SPI +// Either tx_buf or rx_buf can be NULL, which means transfer is write or read only +bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const* tx_buf, uint8_t* rx_buf, size_t xfer_bytes) { (void) rhport; Sercom* sercom = MAX3421_SERCOM; - size_t count = 0; - while (count < tx_len || count < rx_len) { + for (size_t count = 0; count < xfer_bytes; count++) { // Wait for the transmit buffer to be empty while (!sercom->SPI.INTFLAG.bit.DRE); // Write data to be transmitted uint8_t data = 0x00; - if (count < tx_len) { + if (tx_buf) { data = tx_buf[count]; } @@ -351,11 +358,9 @@ bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const *tx_buf, size_t tx_l // Read received data data = (uint8_t) sercom->SPI.DATA.reg; - if (count < rx_len) { + if (rx_buf) { rx_buf[count] = data; } - - count++; } // wait for bus idle and clear flags diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 77912a4c9..787c1e511 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -210,16 +210,21 @@ static max3421_data_t _hcd_data; // API: SPI transfer with MAX3421E, must be implemented by application //--------------------------------------------------------------------+ -void tuh_max3421_spi_cs_api(uint8_t rhport, bool active); -bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const * tx_buf, size_t tx_len, uint8_t * rx_buf, size_t rx_len); -void tuh_max3421_int_api(uint8_t rhport, bool enabled); +// API to control MAX3421 SPI CS +extern void tuh_max3421_spi_cs_api(uint8_t rhport, bool active); -static void handle_connect_irq(uint8_t rhport, bool in_isr); -static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr); +// API to transfer data with MAX3421 SPI +// Either tx_buf or rx_buf can be NULL, which means transfer is write or read only +extern bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const* tx_buf, uint8_t* rx_buf, size_t xfer_bytes); + +// API to enable/disable MAX3421 INTR pin interrupt +extern void tuh_max3421_int_api(uint8_t rhport, bool enabled); //--------------------------------------------------------------------+ // SPI Helper //--------------------------------------------------------------------+ +static void handle_connect_irq(uint8_t rhport, bool in_isr); +static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr); static void max3421_spi_lock(uint8_t rhport, bool in_isr) { // disable interrupt and mutex lock (for pre-emptive RTOS) if not in_isr @@ -249,9 +254,9 @@ static void fifo_write(uint8_t rhport, uint8_t reg, uint8_t const * buffer, uint max3421_spi_lock(rhport, in_isr); - tuh_max3421_spi_xfer_api(rhport, ®, 1, &hirq, 1); + tuh_max3421_spi_xfer_api(rhport, ®, &hirq, 1); _hcd_data.hirq = hirq; - tuh_max3421_spi_xfer_api(rhport, buffer, len, NULL, 0); + tuh_max3421_spi_xfer_api(rhport, buffer, NULL, len); max3421_spi_unlock(rhport, in_isr); @@ -263,9 +268,9 @@ static void fifo_read(uint8_t rhport, uint8_t * buffer, uint16_t len, bool in_is max3421_spi_lock(rhport, in_isr); - tuh_max3421_spi_xfer_api(rhport, ®, 1, &hirq, 1); + tuh_max3421_spi_xfer_api(rhport, ®, &hirq, 1); _hcd_data.hirq = hirq; - tuh_max3421_spi_xfer_api(rhport, NULL, 0, buffer, len); + tuh_max3421_spi_xfer_api(rhport, NULL, buffer, len); max3421_spi_unlock(rhport, in_isr); } @@ -276,7 +281,7 @@ static void reg_write(uint8_t rhport, uint8_t reg, uint8_t data, bool in_isr) { max3421_spi_lock(rhport, in_isr); - tuh_max3421_spi_xfer_api(rhport, tx_buf, 2, rx_buf, 2); + tuh_max3421_spi_xfer_api(rhport, tx_buf, rx_buf, 2); max3421_spi_unlock(rhport, in_isr); @@ -290,7 +295,7 @@ static uint8_t reg_read(uint8_t rhport, uint8_t reg, bool in_isr) { max3421_spi_lock(rhport, in_isr); - bool ret = tuh_max3421_spi_xfer_api(rhport, tx_buf, 2, rx_buf, 2); + bool ret = tuh_max3421_spi_xfer_api(rhport, tx_buf, rx_buf, 2); max3421_spi_unlock(rhport, in_isr); -- cgit v1.3.1 From ce627f431831e1fbaa3bb7bad35a489b8006b749 Mon Sep 17 00:00:00 2001 From: "denis.krasutski" Date: Fri, 6 Oct 2023 13:04:54 +0300 Subject: feat(ch32f20x): add support of ch32f20x --- .gitignore | 1 + README.rst | 2 +- docs/reference/dependencies.rst | 1 + docs/reference/supported.rst | 5 +- hw/bsp/board_mcu.h | 3 + hw/bsp/ch32f20x/boards/ch32f205r-r0/board.h | 59 ++ hw/bsp/ch32f20x/boards/ch32f205r-r0/board.mk | 7 + hw/bsp/ch32f20x/ch32f205.ld | 111 +++ hw/bsp/ch32f20x/ch32f20x_conf.h | 40 + hw/bsp/ch32f20x/ch32f20x_it.c | 35 + hw/bsp/ch32f20x/ch32f20x_it.h | 25 + hw/bsp/ch32f20x/core_cm3.h | 11 + hw/bsp/ch32f20x/debug_uart.c | 105 +++ hw/bsp/ch32f20x/debug_uart.h | 31 + hw/bsp/ch32f20x/family.c | 141 ++++ hw/bsp/ch32f20x/family.mk | 30 + hw/bsp/ch32f20x/startup_gcc_ch32f20x_d8c.s | 493 +++++++++++ hw/bsp/ch32f20x/system_ch32f20x.c | 1122 ++++++++++++++++++++++++++ hw/bsp/ch32f20x/system_ch32f20x.h | 28 + hw/bsp/ch32v307/family.mk | 2 +- src/common/tusb_mcu.h | 4 + src/portable/wch/ch32_usbhs_reg.h | 349 ++++++++ src/portable/wch/ch32v307/ch32_usbhs_reg.h | 345 -------- src/portable/wch/ch32v307/dcd_usbhs.c | 391 --------- src/portable/wch/dcd_ch32_usbhs.c | 391 +++++++++ src/tusb_option.h | 1 + tools/get_deps.py | 3 + tools/iar_template.ipcf | 4 +- 28 files changed, 2999 insertions(+), 741 deletions(-) create mode 100644 hw/bsp/ch32f20x/boards/ch32f205r-r0/board.h create mode 100644 hw/bsp/ch32f20x/boards/ch32f205r-r0/board.mk create mode 100644 hw/bsp/ch32f20x/ch32f205.ld create mode 100644 hw/bsp/ch32f20x/ch32f20x_conf.h create mode 100644 hw/bsp/ch32f20x/ch32f20x_it.c create mode 100644 hw/bsp/ch32f20x/ch32f20x_it.h create mode 100644 hw/bsp/ch32f20x/core_cm3.h create mode 100644 hw/bsp/ch32f20x/debug_uart.c create mode 100644 hw/bsp/ch32f20x/debug_uart.h create mode 100644 hw/bsp/ch32f20x/family.c create mode 100644 hw/bsp/ch32f20x/family.mk create mode 100644 hw/bsp/ch32f20x/startup_gcc_ch32f20x_d8c.s create mode 100644 hw/bsp/ch32f20x/system_ch32f20x.c create mode 100644 hw/bsp/ch32f20x/system_ch32f20x.h create mode 100644 src/portable/wch/ch32_usbhs_reg.h delete mode 100644 src/portable/wch/ch32v307/ch32_usbhs_reg.h delete mode 100644 src/portable/wch/ch32v307/dcd_usbhs.c create mode 100644 src/portable/wch/dcd_ch32_usbhs.c (limited to 'src/portable') diff --git a/.gitignore b/.gitignore index c665d6c73..e6ccec736 100644 --- a/.gitignore +++ b/.gitignore @@ -81,6 +81,7 @@ hw/mcu/st/stm32u5xx_hal_driver hw/mcu/st/stm32wbxx_hal_driver hw/mcu/ti hw/mcu/wch/ch32v307 +hw/mcu/wch/ch32f20x lib/CMSIS_5 lib/FreeRTOS-Kernel lib/lwip diff --git a/README.rst b/README.rst index aef310b98..919596e67 100644 --- a/README.rst +++ b/README.rst @@ -60,7 +60,7 @@ The stack supports the following MCUs: - **ST:** STM32 series: F0, F1, F2, F3, F4, F7, H7, G0, G4, L0, L1, L4, L4+, WB - **TI:** MSP430, MSP432E4, TM4C123 - **ValentyUSB:** eptri -- **WCH:** CH32V307 +- **WCH:** CH32V307, CH32F20x Here is the list of `Supported Devices`_ that can be used with provided examples. diff --git a/docs/reference/dependencies.rst b/docs/reference/dependencies.rst index 130527e2c..d532a3a1e 100644 --- a/docs/reference/dependencies.rst +++ b/docs/reference/dependencies.rst @@ -56,6 +56,7 @@ hw/mcu/st/stm32u5xx_hal_driver https://github.com/STMicroelectronics/ hw/mcu/st/stm32wbxx_hal_driver https://github.com/STMicroelectronics/stm32wbxx_hal_driver.git 2c5f06638be516c1b772f768456ba637f077bac8 hw/mcu/ti https://github.com/hathach/ti_driver.git 143ed6cc20a7615d042b03b21e070197d473e6e5 hw/mcu/wch/ch32v307 https://github.com/openwch/ch32v307.git 17761f5cf9dbbf2dcf665b7c04934188add20082 +hw/mcu/wch/ch32f20x https://github.com/openwch/ch32f20x.git 77c4095087e5ed2c548ec9058e655d0b8757663b lib/CMSIS_5 https://github.com/ARM-software/CMSIS_5.git 20285262657d1b482d132d20d755c8c330d55c1f lib/FreeRTOS-Kernel https://github.com/FreeRTOS/FreeRTOS-Kernel.git def7d2df2b0506d3d249334974f51e427c17a41c lib/lwip https://github.com/lwip-tcpip/lwip.git 159e31b689577dbf69cf0683bbaffbd71fa5ee10 diff --git a/docs/reference/supported.rst b/docs/reference/supported.rst index aed64782c..8843dd405 100644 --- a/docs/reference/supported.rst +++ b/docs/reference/supported.rst @@ -109,6 +109,8 @@ Supported MCUs | ValentyUSB | eptri | ✔ | ✖ | ✖ | eptri | | +--------------+-----------------------+--------+------+-----------+-------------------+--------------+ | WCH | CH32V307 | ✔ | | ✔ | ch32v307 | | +| +-----------------------+--------+------+-----------+-------------------+--------------+ +| | CH32F20x | ✔ | | ✔ | ch32f205 | | +--------------+-----------------------+--------+------+-----------+-------------------+--------------+ @@ -415,4 +417,5 @@ Tomu WCH --- -- `CH32V307V-R1-1v0 ` +- `CH32V307V-R1-1v0 `__ +- `CH32F205R-R0-1v0 `__ diff --git a/hw/bsp/board_mcu.h b/hw/bsp/board_mcu.h index e5d2bb608..4ce5c4139 100644 --- a/hw/bsp/board_mcu.h +++ b/hw/bsp/board_mcu.h @@ -161,6 +161,9 @@ #elif CFG_TUSB_MCU == OPT_MCU_TM4C123 #include "TM4C123.h" +#elif CFG_TUSB_MCU == OPT_MCU_CH32F20X + #include "ch32f20x.h" + #elif TU_CHECK_MCU(OPT_MCU_BCM2711, OPT_MCU_BCM2835, OPT_MCU_BCM2837) // no header needed diff --git a/hw/bsp/ch32f20x/boards/ch32f205r-r0/board.h b/hw/bsp/ch32f20x/boards/ch32f205r-r0/board.h new file mode 100644 index 000000000..d5849bddb --- /dev/null +++ b/hw/bsp/ch32f20x/boards/ch32f205r-r0/board.h @@ -0,0 +1,59 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023, Denis Krasutski + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +// LED: need to wire pin LED1 to PC0 in the P1 header +#define LED_PORT GPIOC +#define LED_PIN GPIO_Pin_1 +#define LED_STATE_ON 0 +#define LED_CLOCK_EN() RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE) + +// Button: need to wire pin KEY to PC1 in the P1 header +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_Pin_0 +#define BUTTON_STATE_ACTIVE 0 +#define BUTTON_CLOCK_EN() RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC, ENABLE) + +// UART +#define UART_DEV USART2 +#define UART_DEV_IRQn USART2_IRQn +#define UART_DEV_IRQHandler USART2_IRQHandler +#define UART_DEV_GPIO_PORT GPIOA +#define UART_DEV_TX_PIN GPIO_Pin_2 +#define UART_DEV_CLK_EN() do { \ + RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA, ENABLE); \ + RCC_APB1PeriphClockCmd(RCC_APB1Periph_USART2, ENABLE); \ + } while(0) + +#ifdef __cplusplus + } +#endif + +#endif diff --git a/hw/bsp/ch32f20x/boards/ch32f205r-r0/board.mk b/hw/bsp/ch32f20x/boards/ch32f205r-r0/board.mk new file mode 100644 index 000000000..f0e9bf30f --- /dev/null +++ b/hw/bsp/ch32f20x/boards/ch32f205r-r0/board.mk @@ -0,0 +1,7 @@ +LD_FILE = $(FAMILY_PATH)/ch32f205.ld + +SRC_S += \ + $(FAMILY_PATH)/startup_gcc_ch32f20x_d8c.s + +CFLAGS += \ + -DCH32F20x_D8C diff --git a/hw/bsp/ch32f20x/ch32f205.ld b/hw/bsp/ch32f20x/ch32f205.ld new file mode 100644 index 000000000..7c8d04cc5 --- /dev/null +++ b/hw/bsp/ch32f20x/ch32f205.ld @@ -0,0 +1,111 @@ +ENTRY(Reset_Handler) + +_Min_Heap_Size = 0x200; +_Min_Stack_Size = 0x400; + +MEMORY +{ + FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 128K + RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 32K +} +SECTIONS +{ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) + . = ALIGN(4); + } >FLASH + + .text : + { + . = ALIGN(4); + _stext = .; + *(.text) + *(.text*) + *(.glue_7) + *(.glue_7t) + *(.eh_frame) + KEEP (*(.init)) + KEEP (*(.fini)) + . = ALIGN(4); + _etext = .; + } >FLASH + .rodata : + { + . = ALIGN(4); + *(.rodata) + *(.rodata*) + . = ALIGN(4); + } >FLASH + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + _sidata = LOADADDR(.data); + .data : + { + . = ALIGN(4); + _sdata = .; + *(.data) + *(.data*) + . = ALIGN(4); + _edata = .; + } >RAM AT> FLASH + . = ALIGN(4); + .bss : + { + _sbss = .; + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + . = ALIGN(4); + _ebss = .; + __bss_end__ = _ebss; + } >RAM + ._user_heap_stack : + { + . = ALIGN(4); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + __HeapStart = .; + . = . + _Min_Heap_Size; + __HeapEnd = .; + __StackLimit = .; + . = . + _Min_Stack_Size; + __StackTop = .; + . = ALIGN(4); + } >RAM +_estack = __StackTop; +_sstack = __StackLimit; + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/ch32f20x/ch32f20x_conf.h b/hw/bsp/ch32f20x/ch32f20x_conf.h new file mode 100644 index 000000000..f94da5dec --- /dev/null +++ b/hw/bsp/ch32f20x/ch32f20x_conf.h @@ -0,0 +1,40 @@ +/********************************** (C) COPYRIGHT ******************************* + * File Name : ch32f20x_conf.h + * Author : WCH + * Version : V1.0.0 + * Date : 2021/08/08 + * Description : Library configuration file. + ********************************************************************************* + * Copyright (c) 2021 Nanjing Qinheng Microelectronics Co., Ltd. + * Attention: This software (modified or not) and binary are used for + * microcontroller manufactured by Nanjing Qinheng Microelectronics. + *******************************************************************************/ +#ifndef __CH32F20x_CONF_H +#define __CH32F20x_CONF_H + +#include "ch32f20x_adc.h" +#include "ch32f20x_bkp.h" +#include "ch32f20x_can.h" +#include "ch32f20x_crc.h" +#include "ch32f20x_dac.h" +#include "ch32f20x_dbgmcu.h" +#include "ch32f20x_dma.h" +#include "ch32f20x_exti.h" +#include "ch32f20x_flash.h" +#include "ch32f20x_fsmc.h" +#include "ch32f20x_gpio.h" +#include "ch32f20x_i2c.h" +#include "ch32f20x_iwdg.h" +#include "ch32f20x_pwr.h" +#include "ch32f20x_rcc.h" +#include "ch32f20x_rtc.h" +#include "ch32f20x_sdio.h" +#include "ch32f20x_spi.h" +#include "ch32f20x_tim.h" +#include "ch32f20x_usart.h" +#include "ch32f20x_wwdg.h" +#include "ch32f20x_it.h" +#include "ch32f20x_misc.h" + +#endif /* __CH32F20x_CONF_H */ + diff --git a/hw/bsp/ch32f20x/ch32f20x_it.c b/hw/bsp/ch32f20x/ch32f20x_it.c new file mode 100644 index 000000000..94e28e380 --- /dev/null +++ b/hw/bsp/ch32f20x/ch32f20x_it.c @@ -0,0 +1,35 @@ +#include "ch32f20x_it.h" + +#include "ch32f20x.h" + +/* -------------------------------------------------------------------------- */ + +void NMI_Handler(void) { + +} + +/* -------------------------------------------------------------------------- */ + +void MemManage_Handler(void) { + +} + +/* -------------------------------------------------------------------------- */ + +void BusFault_Handler(void) { + +} + +/* -------------------------------------------------------------------------- */ + +void UsageFault_Handler(void) { + +} + +/* -------------------------------------------------------------------------- */ + +void DebugMon_Handler(void) { + +} + +/* -------------------------------------------------------------------------- */ diff --git a/hw/bsp/ch32f20x/ch32f20x_it.h b/hw/bsp/ch32f20x/ch32f20x_it.h new file mode 100644 index 000000000..34f3bbf96 --- /dev/null +++ b/hw/bsp/ch32f20x/ch32f20x_it.h @@ -0,0 +1,25 @@ +/********************************** (C) COPYRIGHT ******************************* +* File Name : ch32f20x_it.h +* Author : WCH +* Version : V1.0.0 +* Date : 2021/08/08 +* Description : This file contains the headers of the interrupt handlers. +********************************************************************************* +* Copyright (c) 2021 Nanjing Qinheng Microelectronics Co., Ltd. +* Attention: This software (modified or not) and binary are used for +* microcontroller manufactured by Nanjing Qinheng Microelectronics. +*******************************************************************************/ +#ifndef __CH32F20xIT_H +#define __CH32F20xIT_H + +#include "ch32f20x.h" + +void NMI_Handler(void); +void HardFault_Handler(void); +void MemManage_Handler(void); +void BusFault_Handler(void); +void UsageFault_Handler(void); +void DebugMon_Handler(void); + + +#endif /* __CH32F20xIT_H */ diff --git a/hw/bsp/ch32f20x/core_cm3.h b/hw/bsp/ch32f20x/core_cm3.h new file mode 100644 index 000000000..c35a4eec3 --- /dev/null +++ b/hw/bsp/ch32f20x/core_cm3.h @@ -0,0 +1,11 @@ +/* There is core_cm3.h wrapper just to avoid warnings from CMSIS headers */ +/* if you want use original file add to make file: + INC += \ + $(TOP)/$(CH32F20X_SDK_SRC)/CMSIS +*/ +#pragma GCC diagnostic push +#pragma GCC diagnostic ignored "-Wstrict-prototypes" + +#include <../../CMSIS/core_cm3.h> + +#pragma GCC diagnostic pop diff --git a/hw/bsp/ch32f20x/debug_uart.c b/hw/bsp/ch32f20x/debug_uart.c new file mode 100644 index 000000000..a595eb6f7 --- /dev/null +++ b/hw/bsp/ch32f20x/debug_uart.c @@ -0,0 +1,105 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Denis Krasutski + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ +#include + +#include "board.h" +#include "debug_uart.h" + +#define UART_RINGBUFFER_SIZE_TX 64 +#define UART_RINGBUFFER_MASK_TX (UART_RINGBUFFER_SIZE_TX-1) + +static char tx_buf[UART_RINGBUFFER_SIZE_TX]; +static unsigned int tx_produce = 0; +static volatile unsigned int tx_consume = 0; + +void UART_DEV_IRQHandler(void) +{ + if(USART_GetITStatus(UART_DEV, USART_IT_TC) != RESET) { + USART_ClearITPendingBit(UART_DEV, USART_IT_TC); + + if(tx_consume != tx_produce) { + USART_SendData(UART_DEV, tx_buf[tx_consume]); + tx_consume = (tx_consume + 1) & UART_RINGBUFFER_MASK_TX; + } + } +} + +void uart_write(char c) +{ + unsigned int tx_produce_next = (tx_produce + 1) & UART_RINGBUFFER_MASK_TX; + + NVIC_DisableIRQ(UART_DEV_IRQn); + if((tx_consume != tx_produce) || (USART_GetFlagStatus(UART_DEV, USART_FLAG_TXE) == RESET)) { + tx_buf[tx_produce] = c; + tx_produce = tx_produce_next; + } else { + USART_SendData(UART_DEV, c); + } + NVIC_EnableIRQ(UART_DEV_IRQn); +} + +void uart_sync(void) +{ + while(tx_consume != tx_produce) { + //Waiting for transfer complete + } +} + +void usart_printf_init(uint32_t baudrate) +{ + tx_produce = 0; + tx_consume = 0; + + UART_DEV_CLK_EN(); + + GPIO_InitTypeDef gpio_config = { + .GPIO_Pin = UART_DEV_TX_PIN, + .GPIO_Speed = GPIO_Speed_50MHz, + .GPIO_Mode = GPIO_Mode_AF_PP, + }; + GPIO_Init(UART_DEV_GPIO_PORT, &gpio_config); + + USART_InitTypeDef uart_config = { + .USART_BaudRate = baudrate, + .USART_WordLength = USART_WordLength_8b, + .USART_StopBits = USART_StopBits_1, + .USART_Parity = USART_Parity_No, + .USART_HardwareFlowControl = USART_HardwareFlowControl_None, + .USART_Mode = USART_Mode_Tx, + }; + + USART_Init(UART_DEV, &uart_config); + USART_ITConfig(UART_DEV, USART_IT_TC, ENABLE); + USART_Cmd(UART_DEV, ENABLE); + + NVIC_InitTypeDef nvic_config = { + .NVIC_IRQChannel = UART_DEV_IRQn, + .NVIC_IRQChannelPreemptionPriority = 1, + .NVIC_IRQChannelSubPriority = 3, + .NVIC_IRQChannelCmd = ENABLE, + }; + NVIC_Init(&nvic_config); +} diff --git a/hw/bsp/ch32f20x/debug_uart.h b/hw/bsp/ch32f20x/debug_uart.h new file mode 100644 index 000000000..10284cf6f --- /dev/null +++ b/hw/bsp/ch32f20x/debug_uart.h @@ -0,0 +1,31 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Denis Krasutski + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include + +void uart_write(char c); +void uart_sync(void); +void usart_printf_init(uint32_t baudrate); diff --git a/hw/bsp/ch32f20x/family.c b/hw/bsp/ch32f20x/family.c new file mode 100644 index 000000000..9717832d6 --- /dev/null +++ b/hw/bsp/ch32f20x/family.c @@ -0,0 +1,141 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Denis Krasutski + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "stdio.h" +#include "debug_uart.h" + +#include "ch32f20x.h" + +#include "bsp/board_api.h" +#include "board.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ + +void USBHS_IRQHandler(void) +{ + tud_int_handler(0); +} + +void board_init(void) { + + /* Disable interrupts during init */ + __disable_irq(); + +#if CFG_TUSB_OS == OPT_OS_NONE + SysTick_Config(SystemCoreClock / 1000); +#endif + +#if CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(USBHS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); +#endif + + usart_printf_init(115200); + + // USB HS Clock config + RCC_USBCLK48MConfig(RCC_USBCLK48MCLKSource_USBPHY); + RCC_USBHSPLLCLKConfig(RCC_HSBHSPLLCLKSource_HSE); + RCC_USBHSConfig(RCC_USBPLL_Div2); + RCC_USBHSPLLCKREFCLKConfig(RCC_USBHSPLLCKREFCLK_4M); + RCC_USBHSPHYPLLALIVEcmd(ENABLE); + RCC_AHBPeriphClockCmd(RCC_AHBPeriph_USBHS, ENABLE); + + // LED + LED_CLOCK_EN(); + GPIO_InitTypeDef led_pin_config = { + .GPIO_Pin = LED_PIN, + .GPIO_Mode = GPIO_Mode_Out_OD, + .GPIO_Speed = GPIO_Speed_50MHz, + }; + GPIO_Init(LED_PORT, &led_pin_config); + + // Button + BUTTON_CLOCK_EN(); + GPIO_InitTypeDef button_pin_config = { + .GPIO_Pin = BUTTON_PIN, + .GPIO_Mode = GPIO_Mode_IPU, + .GPIO_Speed = GPIO_Speed_50MHz, + }; + GPIO_Init(BUTTON_PORT, &button_pin_config); + + /* Enable interrupts globally */ + __enable_irq(); +} + +#if CFG_TUSB_OS == OPT_OS_NONE + +volatile uint32_t system_ticks = 0; + +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} + +#endif + +void HardFault_Handler(void) +{ + __asm("BKPT #0\n"); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + GPIO_WriteBit(LED_PORT, LED_PIN, state); +} + +uint32_t board_button_read(void) +{ + return BUTTON_STATE_ACTIVE == GPIO_ReadInputDataBit(BUTTON_PORT, BUTTON_PIN); +} + +int board_uart_read(uint8_t *buf, int len) +{ + (void) buf; + (void) len; + return 0; +} + +int board_uart_write(void const *buf, int len) +{ + int txsize = len; + while ( txsize-- ) + { + uart_write(*(uint8_t const*) buf); + buf++; + } + return len; +} diff --git a/hw/bsp/ch32f20x/family.mk b/hw/bsp/ch32f20x/family.mk new file mode 100644 index 000000000..c08451b9c --- /dev/null +++ b/hw/bsp/ch32f20x/family.mk @@ -0,0 +1,30 @@ +# Submodules +CH32F20X_SDK = hw/mcu/wch/ch32f20x +DEPS_SUBMODULES += $(CH32F20X_SDK) + +# WCH-SDK paths +CH32F20X_SDK_SRC = $(CH32F20X_SDK)/EVT/EXAM/SRC + +include $(TOP)/$(BOARD_PATH)/board.mk + +CPU_CORE ?= cortex-m3 + +CFLAGS += \ + -DCFG_TUSB_MCU=OPT_MCU_CH32F20X \ + -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED + +SRC_C += \ + src/portable/wch/dcd_ch32_usbhs.c \ + $(CH32F20X_SDK_SRC)/StdPeriphDriver/src/ch32f20x_gpio.c \ + $(CH32F20X_SDK_SRC)/StdPeriphDriver/src/ch32f20x_misc.c \ + $(CH32F20X_SDK_SRC)/StdPeriphDriver/src/ch32f20x_rcc.c \ + $(CH32F20X_SDK_SRC)/StdPeriphDriver/src/ch32f20x_usart.c + +INC += \ + $(TOP)/$(BOARD_PATH) \ + $(TOP)/$(CH32F20X_SDK_SRC)/StdPeriphDriver/inc + +# For freeRTOS port source +FREERTOS_PORTABLE_SRC = $(FREERTOS_PORTABLE_PATH)/ARM_CM3 + +flash: flash-stlink diff --git a/hw/bsp/ch32f20x/startup_gcc_ch32f20x_d8c.s b/hw/bsp/ch32f20x/startup_gcc_ch32f20x_d8c.s new file mode 100644 index 000000000..2ecac2ac1 --- /dev/null +++ b/hw/bsp/ch32f20x/startup_gcc_ch32f20x_d8c.s @@ -0,0 +1,493 @@ +/** + ****************************************************************************** + * @file startup_gcc_ch32f20x_d8c.s + * @author Denis Krasutski + * @brief CH32F205 Devices vector table + * This module performs: + * - Set the initial SP + * - Set the initial PC == Reset_Handler, + * - Set the vector table entries with the exceptions ISR address + * - Branches to main in the C library (which eventually + * calls main()). + * After Reset the Cortex-M3 processor is in Thread mode, + * priority is Privileged, and the Stack is set to Main. + ****************************************************************************** + */ + +.syntax unified +.cpu cortex-m3 +.thumb +.global g_pfnVectors +.global Default_Handler + +/* start address for the initialization values of the .data section. defined in linker script */ +.word _sidata +/* start address for the .data section. defined in linker script */ +.word _sdata +/* end address for the .data section. defined in linker script */ +.word _edata +/* start address for the .bss section. defined in linker script */ +.word _sbss +/* end address for the .bss section. defined in linker script */ +.word _ebss + +.section .text.Reset_Handler +.weak Reset_Handler +.type Reset_Handler, %function +Reset_Handler: + /* set stack pointer */ + ldr sp, =_estack + /* Call the clock system initialization function.*/ + bl SystemInit + /* Copy the data segment initializers from flash to SRAM */ + ldr r0, =_sdata + ldr r1, =_edata + ldr r2, =_sidata + movs r3, #0 + b LoopCopyDataInit +CopyDataInit: + ldr r4, [r2, r3] + str r4, [r0, r3] + adds r3, r3, #4 +LoopCopyDataInit: + adds r4, r0, r3 + cmp r4, r1 + bcc CopyDataInit + + /* Zero fill the bss segment. */ + ldr r2, =_sbss + ldr r4, =_ebss + movs r3, #0 + b LoopFillZerobss +FillZerobss: + str r3, [r2] + adds r2, r2, #4 +LoopFillZerobss: + cmp r2, r4 + bcc FillZerobss + /* Call static constructors */ + bl __libc_init_array + /* Call the application's entry point.*/ + bl main + bx lr + .size Reset_Handler, .-Reset_Handler + +.section .text.Default_Handler,"ax",%progbits +Default_Handler: +Infinite_Loop: + b Infinite_Loop + .size Default_Handler, .-Default_Handler + +/****************************************************************************** +* +* The minimal vector table for a Cortex M3. Note that the proper constructs +* must be placed on this to ensure that it ends up at physical address +* 0x0000.0000. +* +*******************************************************************************/ + .section .isr_vector,"a",%progbits + .type g_pfnVectors, %object + .size g_pfnVectors, .-g_pfnVectors + +g_pfnVectors: + .word _estack + .word Reset_Handler + .word NMI_Handler + .word HardFault_Handler + .word MemManage_Handler + .word BusFault_Handler + .word UsageFault_Handler + .word 0 + .word 0 + .word 0 + .word 0 + .word SVC_Handler + .word DebugMon_Handler + .word 0 + .word PendSV_Handler + .word SysTick_Handler + +/******************************************************************************* + External Interrupts +*******************************************************************************/ +.word WWDG_IRQHandler +.word PVD_IRQHandler +.word TAMPER_IRQHandler +.word RTC_IRQHandler +.word FLASH_IRQHandler +.word RCC_IRQHandler +.word EXTI0_IRQHandler +.word EXTI1_IRQHandler +.word EXTI2_IRQHandler +.word EXTI3_IRQHandler +.word EXTI4_IRQHandler +.word DMA1_Channel1_IRQHandler +.word DMA1_Channel2_IRQHandler +.word DMA1_Channel3_IRQHandler +.word DMA1_Channel4_IRQHandler +.word DMA1_Channel5_IRQHandler +.word DMA1_Channel6_IRQHandler +.word DMA1_Channel7_IRQHandler +.word ADC1_2_IRQHandler +.word USB_HP_CAN1_TX_IRQHandler +.word USB_LP_CAN1_RX0_IRQHandler +.word CAN1_RX1_IRQHandler +.word CAN1_SCE_IRQHandler +.word EXTI9_5_IRQHandler +.word TIM1_BRK_IRQHandler +.word TIM1_UP_IRQHandler +.word TIM1_TRG_COM_IRQHandler +.word TIM1_CC_IRQHandler +.word TIM2_IRQHandler +.word TIM3_IRQHandler +.word TIM4_IRQHandler +.word I2C1_EV_IRQHandler +.word I2C1_ER_IRQHandler +.word I2C2_EV_IRQHandler +.word I2C2_ER_IRQHandler +.word SPI1_IRQHandler +.word SPI2_IRQHandler +.word USART1_IRQHandler +.word USART2_IRQHandler +.word USART3_IRQHandler +.word EXTI15_10_IRQHandler +.word RTCAlarm_IRQHandler +.word 0 +.word TIM8_BRK_IRQHandler +.word TIM8_UP_IRQHandler +.word TIM8_TRG_COM_IRQHandler +.word TIM8_CC_IRQHandler +.word RNG_IRQHandler +.word FSMC_IRQHandler +.word SDIO_IRQHandler +.word TIM5_IRQHandler +.word SPI3_IRQHandler +.word UART4_IRQHandler +.word UART5_IRQHandler +.word TIM6_IRQHandler +.word TIM7_IRQHandler +.word DMA2_Channel1_IRQHandler +.word DMA2_Channel2_IRQHandler +.word DMA2_Channel3_IRQHandler +.word DMA2_Channel4_IRQHandler +.word DMA2_Channel5_IRQHandler +.word ETH_IRQHandler +.word ETH_WKUP_IRQHandler +.word CAN2_TX_IRQHandler +.word CAN2_RX0_IRQHandler +.word CAN2_RX1_IRQHandler +.word CAN2_SCE_IRQHandler +.word OTG_FS_IRQHandler +.word USBHSWakeup_IRQHandler +.word USBHS_IRQHandler +.word DVP_IRQHandler +.word UART6_IRQHandler +.word UART7_IRQHandler +.word UART8_IRQHandler +.word TIM9_BRK_IRQHandler +.word TIM9_UP_IRQHandler +.word TIM9_TRG_COM_IRQHandler +.word TIM9_CC_IRQHandler +.word TIM10_BRK_IRQHandler +.word TIM10_UP_IRQHandler +.word TIM10_TRG_COM_IRQHandler +.word TIM10_CC_IRQHandler +.word DMA2_Channel6_IRQHandler +.word DMA2_Channel7_IRQHandler +.word DMA2_Channel8_IRQHandler +.word DMA2_Channel9_IRQHandler +.word DMA2_Channel10_IRQHandler +.word DMA2_Channel11_IRQHandler + +/******************************************************************************* +* +* Provide weak aliases +* +*******************************************************************************/ +.weak NMI_Handler +.thumb_set NMI_Handler,Default_Handler + +.weak HardFault_Handler +.thumb_set HardFault_Handler,Default_Handler + +.weak MemManage_Handler +.thumb_set MemManage_Handler,Default_Handler + +.weak BusFault_Handler +.thumb_set BusFault_Handler,Default_Handler + +.weak UsageFault_Handler +.thumb_set UsageFault_Handler,Default_Handler + +.weak SVC_Handler +.thumb_set SVC_Handler,Default_Handler + +.weak DebugMon_Handler +.thumb_set DebugMon_Handler,Default_Handler + +.weak PendSV_Handler +.thumb_set PendSV_Handler,Default_Handler + +.weak SysTick_Handler +.thumb_set SysTick_Handler,Default_Handler + +.weak WWDG_IRQHandler +.thumb_set WWDG_IRQHandler,Default_Handler + +.weak PVD_IRQHandler +.thumb_set PVD_IRQHandler,Default_Handler + +.weak TAMPER_IRQHandler +.thumb_set TAMPER_IRQHandler,Default_Handler + +.weak RTC_IRQHandler +.thumb_set RTC_IRQHandler,Default_Handler + +.weak FLASH_IRQHandler +.thumb_set FLASH_IRQHandler,Default_Handler + +.weak RCC_IRQHandler +.thumb_set RCC_IRQHandler,Default_Handler + +.weak EXTI0_IRQHandler +.thumb_set EXTI0_IRQHandler,Default_Handler + +.weak EXTI1_IRQHandler +.thumb_set EXTI1_IRQHandler,Default_Handler + +.weak EXTI2_IRQHandler +.thumb_set EXTI2_IRQHandler,Default_Handler + +.weak EXTI3_IRQHandler +.thumb_set EXTI3_IRQHandler,Default_Handler + +.weak EXTI4_IRQHandler +.thumb_set EXTI4_IRQHandler,Default_Handler + +.weak DMA1_Channel1_IRQHandler +.thumb_set DMA1_Channel1_IRQHandler,Default_Handler + +.weak DMA1_Channel2_IRQHandler +.thumb_set DMA1_Channel2_IRQHandler,Default_Handler + +.weak DMA1_Channel3_IRQHandler +.thumb_set DMA1_Channel3_IRQHandler,Default_Handler + +.weak DMA1_Channel4_IRQHandler +.thumb_set DMA1_Channel4_IRQHandler,Default_Handler + +.weak DMA1_Channel5_IRQHandler +.thumb_set DMA1_Channel5_IRQHandler,Default_Handler + +.weak DMA1_Channel6_IRQHandler +.thumb_set DMA1_Channel6_IRQHandler,Default_Handler + +.weak DMA1_Channel7_IRQHandler +.thumb_set DMA1_Channel7_IRQHandler,Default_Handler + +.weak ADC1_2_IRQHandler +.thumb_set ADC1_2_IRQHandler,Default_Handler + +.weak USB_HP_CAN1_TX_IRQHandler +.thumb_set USB_HP_CAN1_TX_IRQHandler,Default_Handler + +.weak USB_LP_CAN1_RX0_IRQHandler +.thumb_set USB_LP_CAN1_RX0_IRQHandler,Default_Handler + +.weak CAN1_RX1_IRQHandler +.thumb_set CAN1_RX1_IRQHandler,Default_Handler + +.weak CAN1_SCE_IRQHandler +.thumb_set CAN1_SCE_IRQHandler,Default_Handler + +.weak EXTI9_5_IRQHandler +.thumb_set EXTI9_5_IRQHandler,Default_Handler + +.weak TIM1_BRK_IRQHandler +.thumb_set TIM1_BRK_IRQHandler,Default_Handler + +.weak TIM1_UP_IRQHandler +.thumb_set TIM1_UP_IRQHandler,Default_Handler + +.weak TIM1_TRG_COM_IRQHandler +.thumb_set TIM1_TRG_COM_IRQHandler,Default_Handler + +.weak TIM1_CC_IRQHandler +.thumb_set TIM1_CC_IRQHandler,Default_Handler + +.weak TIM2_IRQHandler +.thumb_set TIM2_IRQHandler,Default_Handler + +.weak TIM3_IRQHandler +.thumb_set TIM3_IRQHandler,Default_Handler + +.weak TIM4_IRQHandler +.thumb_set TIM4_IRQHandler,Default_Handler + +.weak I2C1_EV_IRQHandler +.thumb_set I2C1_EV_IRQHandler,Default_Handler + +.weak I2C1_ER_IRQHandler +.thumb_set I2C1_ER_IRQHandler,Default_Handler + +.weak I2C2_EV_IRQHandler +.thumb_set I2C2_EV_IRQHandler,Default_Handler + +.weak I2C2_ER_IRQHandler +.thumb_set I2C2_ER_IRQHandler,Default_Handler + +.weak SPI1_IRQHandler +.thumb_set SPI1_IRQHandler,Default_Handler + +.weak SPI2_IRQHandler +.thumb_set SPI2_IRQHandler,Default_Handler + +.weak USART1_IRQHandler +.thumb_set USART1_IRQHandler,Default_Handler + +.weak USART2_IRQHandler +.thumb_set USART2_IRQHandler,Default_Handler + +.weak USART3_IRQHandler +.thumb_set USART3_IRQHandler,Default_Handler + +.weak EXTI15_10_IRQHandler +.thumb_set EXTI15_10_IRQHandler,Default_Handler + +.weak RTCAlarm_IRQHandler +.thumb_set RTCAlarm_IRQHandler,Default_Handler + +.weak TIM8_BRK_IRQHandler +.thumb_set TIM8_BRK_IRQHandler,Default_Handler + +.weak TIM8_UP_IRQHandler +.thumb_set TIM8_UP_IRQHandler,Default_Handler + +.weak TIM8_TRG_COM_IRQHandler +.thumb_set TIM8_TRG_COM_IRQHandler,Default_Handler + +.weak TIM8_CC_IRQHandler +.thumb_set TIM8_CC_IRQHandler,Default_Handler + +.weak RNG_IRQHandler +.thumb_set RNG_IRQHandler,Default_Handler + +.weak FSMC_IRQHandler +.thumb_set FSMC_IRQHandler,Default_Handler + +.weak SDIO_IRQHandler +.thumb_set SDIO_IRQHandler,Default_Handler + +.weak TIM5_IRQHandler +.thumb_set TIM5_IRQHandler,Default_Handler + +.weak SPI3_IRQHandler +.thumb_set SPI3_IRQHandler,Default_Handler + +.weak UART4_IRQHandler +.thumb_set UART4_IRQHandler,Default_Handler + +.weak UART5_IRQHandler +.thumb_set UART5_IRQHandler,Default_Handler + +.weak TIM6_IRQHandler +.thumb_set TIM6_IRQHandler,Default_Handler + +.weak TIM7_IRQHandler +.thumb_set TIM7_IRQHandler,Default_Handler + +.weak DMA2_Channel1_IRQHandler +.thumb_set DMA2_Channel1_IRQHandler,Default_Handler + +.weak DMA2_Channel2_IRQHandler +.thumb_set DMA2_Channel2_IRQHandler,Default_Handler + +.weak DMA2_Channel3_IRQHandler +.thumb_set DMA2_Channel3_IRQHandler,Default_Handler + +.weak DMA2_Channel4_IRQHandler +.thumb_set DMA2_Channel4_IRQHandler,Default_Handler + +.weak DMA2_Channel5_IRQHandler +.thumb_set DMA2_Channel5_IRQHandler,Default_Handler + +.weak ETH_IRQHandler +.thumb_set ETH_IRQHandler,Default_Handler + +.weak ETH_WKUP_IRQHandler +.thumb_set ETH_WKUP_IRQHandler,Default_Handler + +.weak CAN2_TX_IRQHandler +.thumb_set CAN2_TX_IRQHandler,Default_Handler + +.weak CAN2_RX0_IRQHandler +.thumb_set CAN2_RX0_IRQHandler,Default_Handler + +.weak CAN2_RX1_IRQHandler +.thumb_set CAN2_RX1_IRQHandler,Default_Handler + +.weak CAN2_SCE_IRQHandler +.thumb_set CAN2_SCE_IRQHandler,Default_Handler + +.weak OTG_FS_IRQHandler +.thumb_set OTG_FS_IRQHandler,Default_Handler + +.weak USBHSWakeup_IRQHandler +.thumb_set USBHSWakeup_IRQHandler,Default_Handler + +.weak USBHS_IRQHandler +.thumb_set USBHS_IRQHandler,Default_Handler + +.weak DVP_IRQHandler +.thumb_set DVP_IRQHandler,Default_Handler + +.weak UART6_IRQHandler +.thumb_set UART6_IRQHandler,Default_Handler + +.weak UART7_IRQHandler +.thumb_set UART7_IRQHandler,Default_Handler + +.weak UART8_IRQHandler +.thumb_set UART8_IRQHandler,Default_Handler + +.weak TIM9_BRK_IRQHandler +.thumb_set TIM9_BRK_IRQHandler,Default_Handler + +.weak TIM9_UP_IRQHandler +.thumb_set TIM9_UP_IRQHandler,Default_Handler + +.weak TIM9_TRG_COM_IRQHandler +.thumb_set TIM9_TRG_COM_IRQHandler,Default_Handler + +.weak TIM9_CC_IRQHandler +.thumb_set TIM9_CC_IRQHandler,Default_Handler + +.weak TIM10_BRK_IRQHandler +.thumb_set TIM10_BRK_IRQHandler,Default_Handler + +.weak TIM10_UP_IRQHandler +.thumb_set TIM10_UP_IRQHandler,Default_Handler + +.weak TIM10_TRG_COM_IRQHandler +.thumb_set TIM10_TRG_COM_IRQHandler,Default_Handler + +.weak TIM10_CC_IRQHandler +.thumb_set TIM10_CC_IRQHandler,Default_Handler + +.weak DMA2_Channel6_IRQHandler +.thumb_set DMA2_Channel6_IRQHandler,Default_Handler + +.weak DMA2_Channel7_IRQHandler +.thumb_set DMA2_Channel7_IRQHandler,Default_Handler + +.weak DMA2_Channel8_IRQHandler +.thumb_set DMA2_Channel8_IRQHandler,Default_Handler + +.weak DMA2_Channel9_IRQHandler +.thumb_set DMA2_Channel9_IRQHandler,Default_Handler + +.weak DMA2_Channel10_IRQHandler +.thumb_set DMA2_Channel10_IRQHandler,Default_Handler + +.weak DMA2_Channel11_IRQHandler +.thumb_set DMA2_Channel11_IRQHandler,Default_Handler diff --git a/hw/bsp/ch32f20x/system_ch32f20x.c b/hw/bsp/ch32f20x/system_ch32f20x.c new file mode 100644 index 000000000..0a59b9287 --- /dev/null +++ b/hw/bsp/ch32f20x/system_ch32f20x.c @@ -0,0 +1,1122 @@ +/********************************** (C) COPYRIGHT ******************************* +* File Name : system_ch32f20x.c +* Author : WCH +* Version : V1.0.0 +* Date : 2021/08/08 +* Description : CH32F20x Device Peripheral Access Layer System Source File. +* For CH32F208 HSE = 32Mhz +* For others HSE = 8Mhz +********************************************************************************* +* Copyright (c) 2021 Nanjing Qinheng Microelectronics Co., Ltd. +* Attention: This software (modified or not) and binary are used for +* microcontroller manufactured by Nanjing Qinheng Microelectronics. +*******************************************************************************/ +#include "ch32f20x.h" + +/* +* Uncomment the line corresponding to the desired System clock (SYSCLK) frequency (after +* reset the HSI is used as SYSCLK source). +* If none of the define below is enabled, the HSI is used as System clock source. +*/ + +//#define SYSCLK_FREQ_HSE HSE_VALUE +//#define SYSCLK_FREQ_48MHz_HSE 48000000 +//#define SYSCLK_FREQ_56MHz_HSE 56000000 +//#define SYSCLK_FREQ_72MHz_HSE 72000000 +#define SYSCLK_FREQ_96MHz_HSE 96000000 +//#define SYSCLK_FREQ_120MHz_HSE 120000000 +//#define SYSCLK_FREQ_144MHz_HSE 144000000 +//#define SYSCLK_FREQ_HSI HSI_VALUE +//#define SYSCLK_FREQ_48MHz_HSI 48000000 +//#define SYSCLK_FREQ_56MHz_HSI 56000000 +//#define SYSCLK_FREQ_72MHz_HSI 72000000 +//#define SYSCLK_FREQ_96MHz_HSI 96000000 +//#define SYSCLK_FREQ_120MHz_HSI 120000000 +//#define SYSCLK_FREQ_144MHz_HSI 144000000 + + +/* Uncomment the following line if you need to relocate your vector Table in Internal SRAM */ +/* #define VECT_TAB_SRAM */ + +/* Vector Table base offset field This value must be a multiple of 0x200 */ +#define VECT_TAB_OFFSET 0x0 + +/* Clock Definitions */ +#ifdef SYSCLK_FREQ_HSE +uint32_t SystemCoreClock = SYSCLK_FREQ_HSE; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_48MHz_HSE +uint32_t SystemCoreClock = SYSCLK_FREQ_48MHz_HSE; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_56MHz_HSE +uint32_t SystemCoreClock = SYSCLK_FREQ_56MHz_HSE; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_72MHz_HSE +uint32_t SystemCoreClock = SYSCLK_FREQ_72MHz_HSE; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_96MHz_HSE +uint32_t SystemCoreClock = SYSCLK_FREQ_96MHz_HSE; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_120MHz_HSE +uint32_t SystemCoreClock = SYSCLK_FREQ_120MHz_HSE; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_144MHz_HSE +uint32_t SystemCoreClock = SYSCLK_FREQ_144MHz_HSE; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_48MHz_HSI +uint32_t SystemCoreClock = SYSCLK_FREQ_48MHz_HSI; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_56MHz_HSI +uint32_t SystemCoreClock = SYSCLK_FREQ_56MHz_HSI; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_72MHz_HSI +uint32_t SystemCoreClock = SYSCLK_FREQ_72MHz_HSI; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_96MHz_HSI +uint32_t SystemCoreClock = SYSCLK_FREQ_96MHz_HSI; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_120MHz_HSI +uint32_t SystemCoreClock = SYSCLK_FREQ_120MHz_HSI; /* System Clock Frequency (Core Clock) */ +#elif defined SYSCLK_FREQ_144MHz_HSI +uint32_t SystemCoreClock = SYSCLK_FREQ_144MHz_HSI; /* System Clock Frequency (Core Clock) */ +#else +uint32_t SystemCoreClock = HSI_VALUE; /* System Clock Frequency (Core Clock) */ + +#endif + +__I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; + +/* system_private_function_proto_types */ +static void SetSysClock( void ); + +#ifdef SYSCLK_FREQ_HSE +static void SetSysClockToHSE( void ); +#elif defined SYSCLK_FREQ_48MHz_HSE +static void SetSysClockTo48_HSE( void ); +#elif defined SYSCLK_FREQ_56MHz_HSE +static void SetSysClockTo56_HSE( void ); +#elif defined SYSCLK_FREQ_72MHz_HSE +static void SetSysClockTo72_HSE( void ); +#elif defined SYSCLK_FREQ_96MHz_HSE +static void SetSysClockTo96_HSE( void ); +#elif defined SYSCLK_FREQ_120MHz_HSE +static void SetSysClockTo120_HSE( void ); +#elif defined SYSCLK_FREQ_144MHz_HSE +static void SetSysClockTo144_HSE( void ); +#elif defined SYSCLK_FREQ_48MHz_HSI +static void SetSysClockTo48_HSI( void ); +#elif defined SYSCLK_FREQ_56MHz_HSI +static void SetSysClockTo56_HSI( void ); +#elif defined SYSCLK_FREQ_72MHz_HSI +static void SetSysClockTo72_HSI( void ); +#elif defined SYSCLK_FREQ_96MHz_HSI +static void SetSysClockTo96_HSI( void ); +#elif defined SYSCLK_FREQ_120MHz_HSI +static void SetSysClockTo120_HSI( void ); +#elif defined SYSCLK_FREQ_144MHz_HSI +static void SetSysClockTo144_HSI( void ); + +#endif + + +/********************************************************************* + * @fn SystemInit + * + * @brief Setup the microcontroller system Initialize the Embedded Flash Interface, + * the PLL and update the SystemCoreClock variable. + * + * @return none + */ +void SystemInit( void ) +{ + RCC->CTLR |= ( uint32_t )0x00000001; + +#ifdef CH32F20x_D8C + RCC->CFGR0 &= ( uint32_t )0xF8FF0000; +#else + RCC->CFGR0 &= ( uint32_t )0xF0FF0000; +#endif + + RCC->CTLR &= ( uint32_t )0xFEF6FFFF; + RCC->CTLR &= ( uint32_t )0xFFFBFFFF; + RCC->CFGR0 &= ( uint32_t )0xFF80FFFF; +#ifdef CH32F20x_D8C + RCC->CTLR &= ( uint32_t )0xEBFFFFFF; + RCC->INTR = 0x00FF0000; + RCC->CFGR2 = 0x00000000; +#else + RCC->INTR = 0x009F0000; +#endif + + SetSysClock(); + +#ifdef VECT_TAB_SRAM + SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */ +#else + SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */ +#endif +} + +/********************************************************************* + * @fn SystemCoreClockUpdate + * + * @brief Update SystemCoreClock variable according to Clock Register Values. + * + * @return none + */ +void SystemCoreClockUpdate( void ) +{ + uint32_t tmp = 0, pllmull = 0, pllsource = 0; + uint8_t Pll_6_5 = 0; + +#if defined (CH32F20x_D8C) + uint8_t Pll2mull = 0; + +#endif + + tmp = RCC->CFGR0 & RCC_SWS; + + switch( tmp ) + { + case 0x00: + SystemCoreClock = HSI_VALUE; + break; + case 0x04: + SystemCoreClock = HSE_VALUE; + break; + case 0x08: + pllmull = RCC->CFGR0 & RCC_PLLMULL; + pllsource = RCC->CFGR0 & RCC_PLLSRC; + pllmull = ( pllmull >> 18 ) + 2; + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + if( pllmull == 17 ) + { + pllmull = 18; + } +#else + if( pllmull == 2 ) + { + pllmull = 18; + } + if( pllmull == 15 ) + { + pllmull = 13; /* *6.5 */ + Pll_6_5 = 1; + } + if( pllmull == 16 ) + { + pllmull = 15; + } + if( pllmull == 17 ) + { + pllmull = 16; + } +#endif + + if( pllsource == 0x00 ) + { + if(EXTEN->EXTEN_CTR & EXTEN_PLL_HSI_PRE) SystemCoreClock = HSI_VALUE * pllmull; + else SystemCoreClock = (HSI_VALUE >> 1) * pllmull; + } + else + { +#if defined (CH32F20x_D8C) + if(RCC->CFGR2 & (1<<16)){ /* PLL2 */ + SystemCoreClock = HSE_VALUE/(((RCC->CFGR2 & 0xF0)>>4) + 1); /* PREDIV2 */ + + Pll2mull = (uint8_t)((RCC->CFGR2 & 0xF00)>>8); + + if(Pll2mull == 0) SystemCoreClock = (SystemCoreClock * 5)>>1; + else if(Pll2mull == 1) SystemCoreClock = (SystemCoreClock * 25)>>1; + else if(Pll2mull == 15) SystemCoreClock = SystemCoreClock * 20; + else SystemCoreClock = SystemCoreClock * (Pll2mull + 2); + + SystemCoreClock = SystemCoreClock/((RCC->CFGR2 & 0xF) + 1); /* PREDIV1 */ + } + else{/* HSE */ + SystemCoreClock = HSE_VALUE/((RCC->CFGR2 & 0xF) + 1); /* PREDIV1 */ + } + + SystemCoreClock = SystemCoreClock * pllmull; +#else + +#if defined (CH32F20x_D8W) + if((RCC->CFGR0 & (3<<22)) == (3<<22)) + { + SystemCoreClock = ((HSE_VALUE>>1)) * pllmull; + } + else +#endif + if( ( RCC->CFGR0 & RCC_PLLXTPRE ) != ( uint32_t )RESET ) + { +#ifdef CH32F20x_D8W + SystemCoreClock = ( ( HSE_VALUE >> 2 ) >> 1 ) * pllmull; +#else + SystemCoreClock = ( HSE_VALUE >> 1 ) * pllmull; +#endif + } + else + { +#ifdef CH32F20x_D8W + SystemCoreClock = ( HSE_VALUE >> 2 ) * pllmull; +#else + SystemCoreClock = HSE_VALUE * pllmull; +#endif + + } +#endif + } + + if( Pll_6_5 == 1 ) SystemCoreClock = ( SystemCoreClock / 2 ); + + break; + default: + SystemCoreClock = HSI_VALUE; + break; + } + + tmp = AHBPrescTable[( ( RCC->CFGR0 & RCC_HPRE ) >> 4 )]; + SystemCoreClock >>= tmp; +} + + + +/********************************************************************* + * @fn SetSysClock + * + * @brief Configures the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClock( void ) +{ +#ifdef SYSCLK_FREQ_HSE + SetSysClockToHSE(); +#elif defined SYSCLK_FREQ_48MHz_HSE + SetSysClockTo48_HSE(); +#elif defined SYSCLK_FREQ_56MHz_HSE + SetSysClockTo56_HSE(); +#elif defined SYSCLK_FREQ_72MHz_HSE + SetSysClockTo72_HSE(); +#elif defined SYSCLK_FREQ_96MHz_HSE + SetSysClockTo96_HSE(); +#elif defined SYSCLK_FREQ_120MHz_HSE + SetSysClockTo120_HSE(); +#elif defined SYSCLK_FREQ_144MHz_HSE + SetSysClockTo144_HSE(); +#elif defined SYSCLK_FREQ_48MHz_HSI + SetSysClockTo48_HSI(); +#elif defined SYSCLK_FREQ_56MHz_HSI + SetSysClockTo56_HSI(); +#elif defined SYSCLK_FREQ_72MHz_HSI + SetSysClockTo72_HSI(); +#elif defined SYSCLK_FREQ_96MHz_HSI + SetSysClockTo96_HSI(); +#elif defined SYSCLK_FREQ_120MHz_HSI + SetSysClockTo120_HSI(); +#elif defined SYSCLK_FREQ_144MHz_HSI + SetSysClockTo144_HSI(); + +#endif + + /* If none of the define above is enabled, the HSI is used as System clock + * source (default after reset) + */ +} + + +#ifdef SYSCLK_FREQ_HSE + +/********************************************************************* + * @fn SetSysClockToHSE + * + * @brief Sets HSE as System clock source and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockToHSE( void ) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + + RCC->CTLR |= ( ( uint32_t )RCC_HSEON ); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CTLR & RCC_HSERDY; + StartUpCounter++; + } + while( ( HSEStatus == 0 ) && ( StartUpCounter != HSE_STARTUP_TIMEOUT ) ); + + if( ( RCC->CTLR & RCC_HSERDY ) != RESET ) + { + HSEStatus = ( uint32_t )0x01; + } + else + { + HSEStatus = ( uint32_t )0x00; + } + + if( HSEStatus == ( uint32_t )0x01 ) + { + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV1; + + /* Select HSE as system clock source + * CH32F20x_D6 (HSE=8Mhz) + * CH32F20x_D8 (HSE=8Mhz) + * CH32F20x_D8W (HSE=32Mhz) + */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_HSE; + + /* Wait till HSE is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x04 ) + { + } + } + else + { + /* If HSE fails to start-up, the application will have wrong clock + * configuration. User can add here some code to deal with this error + */ + } +} + +#elif defined SYSCLK_FREQ_48MHz_HSE + +/********************************************************************* + * @fn SetSysClockTo48_HSE + * + * @brief Sets System clock frequency to 48MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo48_HSE( void ) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + + RCC->CTLR |= ( ( uint32_t )RCC_HSEON ); + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CTLR & RCC_HSERDY; + StartUpCounter++; + } + while( ( HSEStatus == 0 ) && ( StartUpCounter != HSE_STARTUP_TIMEOUT ) ); + + if( ( RCC->CTLR & RCC_HSERDY ) != RESET ) + { + HSEStatus = ( uint32_t )0x01; + } + else + { + HSEStatus = ( uint32_t )0x00; + } + + if( HSEStatus == ( uint32_t )0x01 ) + { + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* CH32F20x_D6-PLL configuration: PLLCLK = HSE * 6 = 48 MHz (HSE=8Mhz) + * CH32F20x_D8-PLL configuration: PLLCLK = HSE * 6 = 48 MHz (HSE=8Mhz) + * CH32F20x_D8W-PLL configuration: PLLCLK = HSE/4 * 6 = 48 MHz(HSE=32Mhz) + */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL6 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL6_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } + } + else + { + /* + * If HSE fails to start-up, the application will have wrong clock + * configuration. User can add here some code to deal with this error + */ + } +} + +#elif defined SYSCLK_FREQ_56MHz_HSE + +/********************************************************************* + * @fn SetSysClockTo56_HSE + * + * @brief Sets System clock frequency to 56MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo56_HSE( void ) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + RCC->CTLR |= ( ( uint32_t )RCC_HSEON ); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CTLR & RCC_HSERDY; + StartUpCounter++; + } + while( ( HSEStatus == 0 ) && ( StartUpCounter != HSE_STARTUP_TIMEOUT ) ); + + if( ( RCC->CTLR & RCC_HSERDY ) != RESET ) + { + HSEStatus = ( uint32_t )0x01; + } + else + { + HSEStatus = ( uint32_t )0x00; + } + + if( HSEStatus == ( uint32_t )0x01 ) + { + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* CH32F20x_D6-PLL configuration: PLLCLK = HSE * 7 = 56 MHz (HSE=8Mhz) + * CH32F20x_D8-PLL configuration: PLLCLK = HSE * 7 = 56 MHz (HSE=8Mhz) + * CH32F20x_D8W-PLL configuration: PLLCLK = HSE/4 * 7 = 56 MHz(HSE=32Mhz) + */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL7 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL7_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } + } + else + { + /* + * If HSE fails to start-up, the application will have wrong clock + * configuration. User can add here some code to deal with this error + */ + } +} + +#elif defined SYSCLK_FREQ_72MHz_HSE + +/********************************************************************* + * @fn SetSysClockTo72_HSE + * + * @brief Sets System clock frequency to 72MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo72_HSE( void ) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + RCC->CTLR |= ( ( uint32_t )RCC_HSEON ); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CTLR & RCC_HSERDY; + StartUpCounter++; + } + while( ( HSEStatus == 0 ) && ( StartUpCounter != HSE_STARTUP_TIMEOUT ) ); + + if( ( RCC->CTLR & RCC_HSERDY ) != RESET ) + { + HSEStatus = ( uint32_t )0x01; + } + else + { + HSEStatus = ( uint32_t )0x00; + } + + if( HSEStatus == ( uint32_t )0x01 ) + { + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* CH32F20x_D6-PLL configuration: PLLCLK = HSE * 9 = 72 MHz (HSE=8Mhz) + * CH32F20x_D8-PLL configuration: PLLCLK = HSE * 9 = 72 MHz (HSE=8Mhz) + * CH32F20x_D8W-PLL configuration: PLLCLK = HSE/4 * 9 = 72 MHz(HSE=32Mhz) + */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | + RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL9 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL9_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } + } + else + { + /* + * If HSE fails to start-up, the application will have wrong clock + * configuration. User can add here some code to deal with this error + */ + } +} + + +#elif defined SYSCLK_FREQ_96MHz_HSE + +/********************************************************************* + * @fn SetSysClockTo96_HSE + * + * @brief Sets System clock frequency to 96MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo96_HSE( void ) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + RCC->CTLR |= ( ( uint32_t )RCC_HSEON ); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CTLR & RCC_HSERDY; + StartUpCounter++; + } + while( ( HSEStatus == 0 ) && ( StartUpCounter != HSE_STARTUP_TIMEOUT ) ); + + if( ( RCC->CTLR & RCC_HSERDY ) != RESET ) + { + HSEStatus = ( uint32_t )0x01; + } + else + { + HSEStatus = ( uint32_t )0x00; + } + + if( HSEStatus == ( uint32_t )0x01 ) + { + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* CH32F20x_D6-PLL configuration: PLLCLK = HSE * 12 = 96 MHz (HSE=8Mhz) + * CH32F20x_D8-PLL configuration: PLLCLK = HSE * 12 = 96 MHz (HSE=8Mhz) + * CH32F20x_D8W-PLL configuration: PLLCLK = HSE/4 * 12 = 96 MHz(HSE=32Mhz) + */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | + RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL12 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL12_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } + } + else + { + /* + * If HSE fails to start-up, the application will have wrong clock + * configuration. User can add here some code to deal with this error + */ + } +} + + +#elif defined SYSCLK_FREQ_120MHz_HSE + +/********************************************************************* + * @fn SetSysClockTo120_HSE + * + * @brief Sets System clock frequency to 120MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo120_HSE(void) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + RCC->CTLR |= ((uint32_t)RCC_HSEON); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CTLR & RCC_HSERDY; + StartUpCounter++; + } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); + + if ((RCC->CTLR & RCC_HSERDY) != RESET) + { + HSEStatus = (uint32_t)0x01; + } + else + { + HSEStatus = (uint32_t)0x00; + } + + if (HSEStatus == (uint32_t)0x01) + { +#if defined (CH32F20x_D8W) + RCC->CFGR0 |= (uint32_t)(3<<22); + /* HCLK = SYSCLK */ + RCC->CFGR0 |= (uint32_t)RCC_HPRE_DIV2; +#else + /* HCLK = SYSCLK */ + RCC->CFGR0 |= (uint32_t)RCC_HPRE_DIV1; +#endif + + /* PCLK2 = HCLK */ + RCC->CFGR0 |= (uint32_t)RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= (uint32_t)RCC_PPRE1_DIV2; + + /* CH32F20x_D6-PLL configuration: PLLCLK = HSE * 15 = 120 MHz (HSE=8Mhz) + * CH32F20x_D8-PLL configuration: PLLCLK = HSE * 15 = 120 MHz (HSE=8Mhz) + * CH32F20x_D8W-PLL configuration: PLLCLK = HSE/2 * 15 = 240 MHz(HSE=32Mhz) + */ + RCC->CFGR0 &= (uint32_t)((uint32_t)~(RCC_PLLSRC | RCC_PLLXTPRE | + RCC_PLLMULL)); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= (uint32_t)(RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL15); +#else + RCC->CFGR0 |= (uint32_t)(RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL15_EXTEN); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while((RCC->CTLR & RCC_PLLRDY) == 0) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= (uint32_t)((uint32_t)~(RCC_SW)); + RCC->CFGR0 |= (uint32_t)RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR0 & (uint32_t)RCC_SWS) != (uint32_t)0x08) + { + } + } + else + { + /* + * If HSE fails to start-up, the application will have wrong clock + * configuration. User can add here some code to deal with this error + */ + } +} + + + +#elif defined SYSCLK_FREQ_144MHz_HSE + +/********************************************************************* + * @fn SetSysClockTo144_HSE + * + * @brief Sets System clock frequency to 144MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo144_HSE( void ) +{ + __IO uint32_t StartUpCounter = 0, HSEStatus = 0; + + RCC->CTLR |= ( ( uint32_t )RCC_HSEON ); + + /* Wait till HSE is ready and if Time out is reached exit */ + do + { + HSEStatus = RCC->CTLR & RCC_HSERDY; + StartUpCounter++; + } + while( ( HSEStatus == 0 ) && ( StartUpCounter != HSE_STARTUP_TIMEOUT ) ); + + if( ( RCC->CTLR & RCC_HSERDY ) != RESET ) + { + HSEStatus = ( uint32_t )0x01; + } + else + { + HSEStatus = ( uint32_t )0x00; + } + + if( HSEStatus == ( uint32_t )0x01 ) + { + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* CH32F20x_D6-PLL configuration: PLLCLK = HSE * 18 = 144 MHz (HSE=8Mhz) + * CH32F20x_D8-PLL configuration: PLLCLK = HSE * 18 = 144 MHz (HSE=8Mhz) + * CH32F20x_D8W-PLL configuration: PLLCLK = HSE/4 * 18 = 144 MHz(HSE=32Mhz) + */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | + RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL18 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSE | RCC_PLLXTPRE_HSE | RCC_PLLMULL18_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } + } + else + { + /* + * If HSE fails to start-up, the application will have wrong clock + * configuration. User can add here some code to deal with this error + */ + } +} + +#elif defined SYSCLK_FREQ_48MHz_HSI + +/********************************************************************* + * @fn SetSysClockTo48_HSI + * + * @brief Sets System clock frequency to 48MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo48_HSI( void ) +{ + EXTEN->EXTEN_CTR |= EXTEN_PLL_HSI_PRE; + + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* PLL configuration: PLLCLK = HSI * 6 = 48 MHz */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL6 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL6_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } +} + +#elif defined SYSCLK_FREQ_56MHz_HSI + +/********************************************************************* + * @fn SetSysClockTo56_HSI + * + * @brief Sets System clock frequency to 56MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo56_HSI( void ) +{ + EXTEN->EXTEN_CTR |= EXTEN_PLL_HSI_PRE; + + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* PLL configuration: PLLCLK = HSI * 7 = 56 MHz */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL7 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL7_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } +} + +#elif defined SYSCLK_FREQ_72MHz_HSI + +/********************************************************************* + * @fn SetSysClockTo72_HSI + * + * @brief Sets System clock frequency to 72MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo72_HSI( void ) +{ + EXTEN->EXTEN_CTR |= EXTEN_PLL_HSI_PRE; + + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* PLL configuration: PLLCLK = HSI * 9 = 72 MHz */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL9 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL9_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } +} + + +#elif defined SYSCLK_FREQ_96MHz_HSI + +/********************************************************************* + * @fn SetSysClockTo96_HSI + * + * @brief Sets System clock frequency to 96MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo96_HSI( void ) +{ + EXTEN->EXTEN_CTR |= EXTEN_PLL_HSI_PRE; + + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* PLL configuration: PLLCLK = HSI * 12 = 96 MHz */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL12 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL12_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } +} + + +#elif defined SYSCLK_FREQ_120MHz_HSI + +/********************************************************************* + * @fn SetSysClockTo120_HSI + * + * @brief Sets System clock frequency to 120MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo120_HSI(void) +{ + EXTEN->EXTEN_CTR |= EXTEN_PLL_HSI_PRE; + + /* HCLK = SYSCLK */ + RCC->CFGR0 |= (uint32_t)RCC_HPRE_DIV1; + + /* PCLK2 = HCLK */ + RCC->CFGR0 |= (uint32_t)RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= (uint32_t)RCC_PPRE1_DIV2; + + /* PLL configuration: PLLCLK = HSI * 15 = 120 MHz */ + RCC->CFGR0 &= (uint32_t)((uint32_t)~(RCC_PLLSRC | RCC_PLLXTPRE | + RCC_PLLMULL)); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL15 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL15_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while((RCC->CTLR & RCC_PLLRDY) == 0) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= (uint32_t)((uint32_t)~(RCC_SW)); + RCC->CFGR0 |= (uint32_t)RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while ((RCC->CFGR0 & (uint32_t)RCC_SWS) != (uint32_t)0x08) + { + } +} + + +#elif defined SYSCLK_FREQ_144MHz_HSI + +/********************************************************************* + * @fn SetSysClockTo144_HSI + * + * @brief Sets System clock frequency to 144MHz and configure HCLK, PCLK2 and PCLK1 prescalers. + * + * @return none + */ +static void SetSysClockTo144_HSI( void ) +{ + EXTEN->EXTEN_CTR |= EXTEN_PLL_HSI_PRE; + + /* HCLK = SYSCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_HPRE_DIV1; + /* PCLK2 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE2_DIV1; + /* PCLK1 = HCLK */ + RCC->CFGR0 |= ( uint32_t )RCC_PPRE1_DIV2; + + /* PLL configuration: PLLCLK = HSI * 18 = 144 MHz */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_PLLSRC | RCC_PLLXTPRE | RCC_PLLMULL ) ); + +#if defined (CH32F20x_D6) || defined (CH32F20x_D8) || defined (CH32F20x_D8W) + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL18 ); +#else + RCC->CFGR0 |= ( uint32_t )( RCC_PLLSRC_HSI_Div2 | RCC_PLLMULL18_EXTEN ); +#endif + + /* Enable PLL */ + RCC->CTLR |= RCC_PLLON; + /* Wait till PLL is ready */ + while( ( RCC->CTLR & RCC_PLLRDY ) == 0 ) + { + } + /* Select PLL as system clock source */ + RCC->CFGR0 &= ( uint32_t )( ( uint32_t )~( RCC_SW ) ); + RCC->CFGR0 |= ( uint32_t )RCC_SW_PLL; + /* Wait till PLL is used as system clock source */ + while( ( RCC->CFGR0 & ( uint32_t )RCC_SWS ) != ( uint32_t )0x08 ) + { + } +} + + +#endif diff --git a/hw/bsp/ch32f20x/system_ch32f20x.h b/hw/bsp/ch32f20x/system_ch32f20x.h new file mode 100644 index 000000000..734c80a5a --- /dev/null +++ b/hw/bsp/ch32f20x/system_ch32f20x.h @@ -0,0 +1,28 @@ +/********************************** (C) COPYRIGHT ******************************* +* File Name : system_ch32f20x.h +* Author : WCH +* Version : V1.0.0 +* Date : 2021/08/08 +* Description : CH32F20x Device Peripheral Access Layer System Header File. +*******************************************************************************/ +#ifndef __SYSTEM_CH32F20x_H +#define __SYSTEM_CH32F20x_H + +#ifdef __cplusplus + extern "C" { +#endif + +extern uint32_t SystemCoreClock; /* System Clock Frequency (Core Clock) */ + +/* System_Exported_Functions */ +extern void SystemInit(void); +extern void SystemCoreClockUpdate(void); + +#ifdef __cplusplus +} +#endif + +#endif /*__CH32F20x_SYSTEM_H */ + + + diff --git a/hw/bsp/ch32v307/family.mk b/hw/bsp/ch32v307/family.mk index 4b06cf429..45f0317ee 100644 --- a/hw/bsp/ch32v307/family.mk +++ b/hw/bsp/ch32v307/family.mk @@ -29,7 +29,7 @@ CFLAGS += \ -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED SRC_C += \ - src/portable/wch/ch32v307/dcd_usbhs.c \ + src/portable/wch/dcd_ch32_usbhs.c \ $(CH32V307_SDK_SRC)/Core/core_riscv.c \ $(CH32V307_SDK_SRC)/Peripheral/src/ch32v30x_gpio.c \ $(CH32V307_SDK_SRC)/Peripheral/src/ch32v30x_misc.c \ diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 8807ff8aa..a72976ae9 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -383,6 +383,10 @@ #elif TU_CHECK_MCU(OPT_MCU_CH32V307) #define TUP_DCD_ENDPOINT_MAX 16 #define TUP_RHPORT_HIGHSPEED 1 + +#elif TU_CHECK_MCU(OPT_MCU_CH32F20X) + #define TUP_DCD_ENDPOINT_MAX 16 + #define TUP_RHPORT_HIGHSPEED 1 #endif diff --git a/src/portable/wch/ch32_usbhs_reg.h b/src/portable/wch/ch32_usbhs_reg.h new file mode 100644 index 000000000..9b956231f --- /dev/null +++ b/src/portable/wch/ch32_usbhs_reg.h @@ -0,0 +1,349 @@ +#ifndef _USB_CH32_USBHS_REG_H +#define _USB_CH32_USBHS_REG_H + +#if (CFG_TUSB_MCU == OPT_MCU_CH32V307) +#include +#elif (CFG_TUSB_MCU == OPT_MCU_CH32F20X) +#include +#endif + +/******************* GLOBAL ******************/ + +// USB CONTROL +#define USBHS_CONTROL_OFFSET 0x00 +#define USBHS_DMA_EN (1 << 0) +#define USBHS_ALL_CLR (1 << 1) +#define USBHS_FORCE_RST (1 << 2) +#define USBHS_INT_BUSY_EN (1 << 3) +#define USBHS_DEV_PU_EN (1 << 4) +#define USBHS_SPEED_MASK (3 << 5) +#define USBHS_FULL_SPEED (0 << 5) +#define USBHS_HIGH_SPEED (1 << 5) +#define USBHS_LOW_SPEED (2 << 5) +#define USBHS_HOST_MODE (1 << 7) + +// USB_INT_EN +#define USBHS_INT_EN_OFFSET 0x02 +#define USBHS_BUS_RST_EN (1 << 0) +#define USBHS_DETECT_EN (1 << 0) +#define USBHS_TRANSFER_EN (1 << 1) +#define USBHS_SUSPEND_EN (1 << 2) +#define USBHS_SOF_ACT_EN (1 << 3) +#define USBHS_FIFO_OV_EN (1 << 4) +#define USBHS_SETUP_ACT_EN (1 << 5) +#define USBHS_ISO_ACT_EN (1 << 6) +#define USBHS_DEV_NAK_EN (1 << 7) + +// USB DEV AD +#define USBHS_DEV_AD_OFFSET 0x03 +// USB FRAME_NO +#define USBHS_FRAME_NO_OFFSET 0x04 +// USB SUSPEND +#define USBHS_SUSPEND_OFFSET 0x06 +#define USBHS_DEV_REMOTE_WAKEUP (1 << 2) +#define USBHS_LINESTATE_MASK (2 << 4) /* Read Only */ + +// RESERVED0 + +// USB SPEED TYPE +#define USBHS_SPEED_TYPE_OFFSET 0x08 +#define USBSPEED_MASK (0x03) + +// USB_MIS_ST +#define USBHS_MIS_ST_OFFSET 0x09 +#define USBHS_SPLIT_CAN (1 << 0) +#define USBHS_ATTACH (1 << 1) +#define USBHS_SUSPEND (1 << 2) +#define USBHS_BUS_RESET (1 << 3) +#define USBHS_R_FIFO_RDY (1 << 4) +#define USBHS_SIE_FREE (1 << 5) +#define USBHS_SOF_ACT (1 << 6) +#define USBHS_SOF_PRES (1 << 7) + +// INT_FLAG +#define USBHS_INT_FLAG_OFFSET 0x0A +#define USBHS_BUS_RST_FLAG (1 << 0) +#define USBHS_DETECT_FLAG (1 << 0) +#define USBHS_TRANSFER_FLAG (1 << 1) +#define USBHS_SUSPEND_FLAG (1 << 2) +#define USBHS_HST_SOF_FLAG (1 << 3) +#define USBHS_FIFO_OV_FLAG (1 << 4) +#define USBHS_SETUP_FLAG (1 << 5) +#define USBHS_ISO_ACT_FLAG (1 << 6) + +// INT_ST +#define USBHS_INT_ST_OFFSET 0x0B +#define USBHS_DEV_UIS_IS_NAK (1 << 7) +#define USBHS_DEV_UIS_TOG_OK (1 << 6) +#define MASK_UIS_TOKEN (3 << 4) +#define MASK_UIS_ENDP (0x0F) +#define MASK_UIS_H_RES (0x0F) + +#define USBHS_TOGGLE_OK (0x40) +#define USBHS_HOST_RES (0x0f) + +//USB_RX_LEN +#define USBHS_RX_LEN_OFFSET 0x0C +/******************* DEVICE ******************/ + +//UEP_CONFIG +#define USBHS_UEP_CONFIG_OFFSET 0x10 +#define USBHS_EP0_T_EN (1 << 0) +#define USBHS_EP0_R_EN (1 << 16) + +#define USBHS_EP1_T_EN (1 << 1) +#define USBHS_EP1_R_EN (1 << 17) + +#define USBHS_EP2_T_EN (1 << 2) +#define USBHS_EP2_R_EN (1 << 18) + +#define USBHS_EP3_T_EN (1 << 3) +#define USBHS_EP3_R_EN (1 << 19) + +#define USBHS_EP4_T_EN (1 << 4) +#define USBHS_EP4_R_EN (1 << 20) + +#define USBHS_EP5_T_EN (1 << 5) +#define USBHS_EP5_R_EN (1 << 21) + +#define USBHS_EP6_T_EN (1 << 6) +#define USBHS_EP6_R_EN (1 << 22) + +#define USBHS_EP7_T_EN (1 << 7) +#define USBHS_EP7_R_EN (1 << 23) + +#define USBHS_EP8_T_EN (1 << 8) +#define USBHS_EP8_R_EN (1 << 24) + +#define USBHS_EP9_T_EN (1 << 9) +#define USBHS_EP9_R_EN (1 << 25) + +#define USBHS_EP10_T_EN (1 << 10) +#define USBHS_EP10_R_EN (1 << 26) + +#define USBHS_EP11_T_EN (1 << 11) +#define USBHS_EP11_R_EN (1 << 27) + +#define USBHS_EP12_T_EN (1 << 12) +#define USBHS_EP12_R_EN (1 << 28) + +#define USBHS_EP13_T_EN (1 << 13) +#define USBHS_EP13_R_EN (1 << 29) + +#define USBHS_EP14_T_EN (1 << 14) +#define USBHS_EP14_R_EN (1 << 30) + +#define USBHS_EP15_T_EN (1 << 15) +#define USBHS_EP15_R_EN (1 << 31) + +//UEP_TYPE +#define USBHS_UEP_TYPE_OFFSET 0x14 +#define USBHS_EP0_T_TYP (1 << 0) +#define USBHS_EP0_R_TYP (1 << 16) + +#define USBHS_EP1_T_TYP (1 << 1) +#define USBHS_EP1_R_TYP (1 << 17) + +#define USBHS_EP2_T_TYP (1 << 2) +#define USBHS_EP2_R_TYP (1 << 18) + +#define USBHS_EP3_T_TYP (1 << 3) +#define USBHS_EP3_R_TYP (1 << 19) + +#define USBHS_EP4_T_TYP (1 << 4) +#define USBHS_EP4_R_TYP (1 << 20) + +#define USBHS_EP5_T_TYP (1 << 5) +#define USBHS_EP5_R_TYP (1 << 21) + +#define USBHS_EP6_T_TYP (1 << 6) +#define USBHS_EP6_R_TYP (1 << 22) + +#define USBHS_EP7_T_TYP (1 << 7) +#define USBHS_EP7_R_TYP (1 << 23) + +#define USBHS_EP8_T_TYP (1 << 8) +#define USBHS_EP8_R_TYP (1 << 24) + +#define USBHS_EP9_T_TYP (1 << 8) +#define USBHS_EP9_R_TYP (1 << 25) + +#define USBHS_EP10_T_TYP (1 << 10) +#define USBHS_EP10_R_TYP (1 << 26) + +#define USBHS_EP11_T_TYP (1 << 11) +#define USBHS_EP11_R_TYP (1 << 27) + +#define USBHS_EP12_T_TYP (1 << 12) +#define USBHS_EP12_R_TYP (1 << 28) + +#define USBHS_EP13_T_TYP (1 << 13) +#define USBHS_EP13_R_TYP (1 << 29) + +#define USBHS_EP14_T_TYP (1 << 14) +#define USBHS_EP14_R_TYP (1 << 30) + +#define USBHS_EP15_T_TYP (1 << 15) +#define USBHS_EP15_R_TYP (1 << 31) + +/* BUF_MOD UEP1~15 */ +#define USBHS_BUF_MOD_OFFSET 0x18 +#define USBHS_EP0_BUF_MOD (1 << 0) +#define USBHS_EP0_ISO_BUF_MOD (1 << 16) + +#define USBHS_EP1_BUF_MOD (1 << 1) +#define USBHS_EP1_ISO_BUF_MOD (1 << 17) + +#define USBHS_EP2_BUF_MOD (1 << 2) +#define USBHS_EP2_ISO_BUF_MOD (1 << 18) + +#define USBHS_EP3_BUF_MOD (1 << 3) +#define USBHS_EP3_ISO_BUF_MOD (1 << 19) + +#define USBHS_EP4_BUF_MOD (1 << 4) +#define USBHS_EP4_ISO_BUF_MOD (1 << 20) + +#define USBHS_EP5_BUF_MOD (1 << 5) +#define USBHS_EP5_ISO_BUF_MOD (1 << 21) + +#define USBHS_EP6_BUF_MOD (1 << 6) +#define USBHS_EP6_ISO_BUF_MOD (1 << 22) + +#define USBHS_EP7_BUF_MOD (1 << 7) +#define USBHS_EP7_ISO_BUF_MOD (1 << 23) + +#define USBHS_EP8_BUF_MOD (1 << 8) +#define USBHS_EP8_ISO_BUF_MOD (1 << 24) + +#define USBHS_EP9_BUF_MOD (1 << 9) +#define USBHS_EP9_ISO_BUF_MOD (1 << 25) + +#define USBHS_EP10_BUF_MOD (1 << 10) +#define USBHS_EP10_ISO_BUF_MOD (1 << 26) + +#define USBHS_EP11_BUF_MOD (1 << 11) +#define USBHS_EP11_ISO_BUF_MOD (1 << 27) + +#define USBHS_EP12_BUF_MOD (1 << 12) +#define USBHS_EP12_ISO_BUF_MOD (1 << 28) + +#define USBHS_EP13_BUF_MOD (1 << 13) +#define USBHS_EP13_ISO_BUF_MOD (1 << 29) + +#define USBHS_EP14_BUF_MOD (1 << 14) +#define USBHS_EP14_ISO_BUF_MOD (1 << 30) + +#define USBHS_EP15_BUF_MOD (1 << 15) +#define USBHS_EP15_ISO_BUF_MOD (1 << 31) +//USBHS_EPn_T_EN USBHS_EPn_R_EN USBHS_EPn_BUF_MOD Description: Arrange from low to high with UEPn_DMA as the starting address +// 0 0 x The endpoint is disabled and the UEPn_*_DMA buffers are not used. +// 1 0 0 The first address of the receive (OUT) buffer is UEPn_RX_DMA +// 1 0 1 RB_UEPn_RX_TOG[0]=0, use buffer UEPn_RX_DMA RB_UEPn_RX_TOG[0]=1, use buffer UEPn_TX_DMA +// 0 1 0 The first address of the transmit (IN) buffer is UEPn_TX_DMA. +// 0 1 1 RB_UEPn_TX_TOG[0]=0, use buffer UEPn_TX_DMA RB_UEPn_TX_TOG[0]=1, use buffer UEPn_RX_DMA + +/* USB0_DMA */ +#define USBHS_UEP0_DMA_OFFSET(n) (0x1C) // endpoint 0 DMA buffer address + +/* USBX_RX_DMA */ +#define USBHS_UEPx_RX_DMA_OFFSET(n) (0x1C + 4 * (n)) // endpoint x DMA buffer address + +#define USBHS_UEPx_TX_DMA_OFFSET(n) (0x58 + 4 * (n)) // endpoint x DMA buffer address + +#define USBHS_UEPx_MAX_LEN_OFFSET(n) (0x98 + 4 * (n)) // endpoint x DMA buffer address + +#define USBHS_UEPx_T_LEN_OFFSET(n) (0xD8 + 4 * (n)) // endpoint x DMA buffer address +#define USBHS_UEPx_TX_CTRL_OFFSET(n) (0xD8 + 4 * (n) + 2) // endpoint x DMA buffer address +#define USBHS_UEPx_RX_CTRL_OFFSET(n) (0xD8 + 4 * (n) + 3) // endpoint x DMA buffer address + +// UEPn_T_LEN +#define USBHS_EP_T_LEN_MASK (0x7FF) + +//UEPn_TX_CTRL +#define USBHS_EP_T_RES_MASK (3 << 0) +#define USBHS_EP_T_RES_ACK (0 << 0) +#define USBHS_EP_T_RES_NYET (1 << 0) +#define USBHS_EP_T_RES_NAK (2 << 0) +#define USBHS_EP_T_RES_STALL (3 << 0) + +#define USBHS_EP_T_TOG_MASK (3 << 3) +#define USBHS_EP_T_TOG_0 (0 << 3) +#define USBHS_EP_T_TOG_1 (1 << 3) +#define USBHS_EP_T_TOG_2 (2 << 3) +#define USBHS_EP_T_TOG_M (3 << 3) + +#define USBHS_EP_T_AUTOTOG (1 << 5) + +//UEPn_RX_CTRL +#define USBHS_EP_R_RES_MASK (3 << 0) +#define USBHS_EP_R_RES_ACK (0 << 0) +#define USBHS_EP_R_RES_NYET (1 << 0) +#define USBHS_EP_R_RES_NAK (2 << 0) +#define USBHS_EP_R_RES_STALL (3 << 0) + +#define USBHS_EP_R_TOG_MASK (3 << 3) +#define USBHS_EP_R_TOG_0 (0 << 3) +#define USBHS_EP_R_TOG_1 (1 << 3) +#define USBHS_EP_R_TOG_2 (2 << 3) +#define USBHS_EP_R_TOG_M (3 << 3) + +#define USBHS_EP_R_AUTOTOG (1 << 5) + +#define USBHS_TOG_MATCH (1 << 6) + +/******************* HOST ******************/ +// USB HOST_CTRL +#define USBHS_SEND_BUS_RESET (1 << 0) +#define USBHS_SEND_BUS_SUSPEND (1 << 1) +#define USBHS_SEND_BUS_RESUME (1 << 2) +#define USBHS_REMOTE_WAKE (1 << 3) +#define USBHS_PHY_SUSPENDM (1 << 4) +#define USBHS_UH_SOFT_FREE (1 << 6) +#define USBHS_SEND_SOF_EN (1 << 7) + +//UH_CONFIG +#define USBHS_HOST_TX_EN (1 << 3) +#define USBHS_HOST_RX_EN (1 << 18) + +// HOST_EP_TYPE +#define USBHS_ENDP_TX_ISO (1 << 3) +#define USBHS_ENDP_RX_ISO (1 << (16 + 2)) + +// R32_UH_EP_PID +#define USBHS_HOST_MASK_TOKEN (0x0f) +#define USBHS_HOST_MASK_ENDP (0x0f << 4) + +//R8_UH_RX_CTRL +#define USBHS_EP_R_RES_MASK (3 << 0) +#define USBHS_EP_R_RES_ACK (0 << 0) +#define USBHS_EP_R_RES_NYET (1 << 0) +#define USBHS_EP_R_RES_NAK (2 << 0) +#define USBHS_EP_R_RES_STALL (3 << 0) + +#define USBHS_UH_R_RES_NO (1 << 2) +#define USBHS_UH_R_TOG_1 (1 << 3) +#define USBHS_UH_R_TOG_2 (2 << 3) +#define USBHS_UH_R_TOG_3 (3 << 3) +#define USBHS_UH_R_TOG_AUTO (1 << 5) +#define USBHS_UH_R_DATA_NO (1 << 6) +//R8_UH_TX_CTRL +#define USBHS_UH_T_RES_MASK (3 << 0) +#define USBHS_UH_T_RES_ACK (0 << 0) +#define USBHS_UH_T_RES_NYET (1 << 0) +#define USBHS_UH_T_RES_NAK (2 << 0) +#define USBHS_UH_T_RES_STALL (3 << 0) + +#define USBHS_UH_T_RES_NO (1 << 2) +#define USBHS_UH_T_TOG_1 (1 << 3) +#define USBHS_UH_T_TOG_2 (2 << 3) +#define USBHS_UH_T_TOG_3 (3 << 3) +#define USBHS_UH_T_TOG_AUTO (1 << 5) +#define USBHS_UH_T_DATA_NO (1 << 6) + +// 00: OUT, 01:SOF, 10:IN, 11:SETUP +#define PID_OUT 0 +#define PID_SOF 1 +#define PID_IN 2 +#define PID_SETUP 3 + +#endif diff --git a/src/portable/wch/ch32v307/ch32_usbhs_reg.h b/src/portable/wch/ch32v307/ch32_usbhs_reg.h deleted file mode 100644 index 5a2c1fbc9..000000000 --- a/src/portable/wch/ch32v307/ch32_usbhs_reg.h +++ /dev/null @@ -1,345 +0,0 @@ -#ifndef _USB_CH32_USBHS_REG_H -#define _USB_CH32_USBHS_REG_H - -#include - -/******************* GLOBAL ******************/ - -// USB CONTROL -#define USBHS_CONTROL_OFFSET 0x00 -#define USBHS_DMA_EN (1 << 0) -#define USBHS_ALL_CLR (1 << 1) -#define USBHS_FORCE_RST (1 << 2) -#define USBHS_INT_BUSY_EN (1 << 3) -#define USBHS_DEV_PU_EN (1 << 4) -#define USBHS_SPEED_MASK (3 << 5) -#define USBHS_FULL_SPEED (0 << 5) -#define USBHS_HIGH_SPEED (1 << 5) -#define USBHS_LOW_SPEED (2 << 5) -#define USBHS_HOST_MODE (1 << 7) - -// USB_INT_EN -#define USBHS_INT_EN_OFFSET 0x02 -#define USBHS_BUS_RST_EN (1 << 0) -#define USBHS_DETECT_EN (1 << 0) -#define USBHS_TRANSFER_EN (1 << 1) -#define USBHS_SUSPEND_EN (1 << 2) -#define USBHS_SOF_ACT_EN (1 << 3) -#define USBHS_FIFO_OV_EN (1 << 4) -#define USBHS_SETUP_ACT_EN (1 << 5) -#define USBHS_ISO_ACT_EN (1 << 6) -#define USBHS_DEV_NAK_EN (1 << 7) - -// USB DEV AD -#define USBHS_DEV_AD_OFFSET 0x03 -// USB FRAME_NO -#define USBHS_FRAME_NO_OFFSET 0x04 -// USB SUSPEND -#define USBHS_SUSPEND_OFFSET 0x06 -#define USBHS_DEV_REMOTE_WAKEUP (1 << 2) -#define USBHS_LINESTATE_MASK (2 << 4) /* Read Only */ - -// RESERVED0 - -// USB SPEED TYPE -#define USBHS_SPEED_TYPE_OFFSET 0x08 -#define USBSPEED_MASK (0x03) - -// USB_MIS_ST -#define USBHS_MIS_ST_OFFSET 0x09 -#define USBHS_SPLIT_CAN (1 << 0) -#define USBHS_ATTACH (1 << 1) -#define USBHS_SUSPEND (1 << 2) -#define USBHS_BUS_RESET (1 << 3) -#define USBHS_R_FIFO_RDY (1 << 4) -#define USBHS_SIE_FREE (1 << 5) -#define USBHS_SOF_ACT (1 << 6) -#define USBHS_SOF_PRES (1 << 7) - -// INT_FLAG -#define USBHS_INT_FLAG_OFFSET 0x0A -#define USBHS_BUS_RST_FLAG (1 << 0) -#define USBHS_DETECT_FLAG (1 << 0) -#define USBHS_TRANSFER_FLAG (1 << 1) -#define USBHS_SUSPEND_FLAG (1 << 2) -#define USBHS_HST_SOF_FLAG (1 << 3) -#define USBHS_FIFO_OV_FLAG (1 << 4) -#define USBHS_SETUP_FLAG (1 << 5) -#define USBHS_ISO_ACT_FLAG (1 << 6) - -// INT_ST -#define USBHS_INT_ST_OFFSET 0x0B -#define USBHS_DEV_UIS_IS_NAK (1 << 7) -#define USBHS_DEV_UIS_TOG_OK (1 << 6) -#define MASK_UIS_TOKEN (3 << 4) -#define MASK_UIS_ENDP (0x0F) -#define MASK_UIS_H_RES (0x0F) - -#define USBHS_TOGGLE_OK (0x40) -#define USBHS_HOST_RES (0x0f) - -//USB_RX_LEN -#define USBHS_RX_LEN_OFFSET 0x0C -/******************* DEVICE ******************/ - -//UEP_CONFIG -#define USBHS_UEP_CONFIG_OFFSET 0x10 -#define USBHS_EP0_T_EN (1 << 0) -#define USBHS_EP0_R_EN (1 << 16) - -#define USBHS_EP1_T_EN (1 << 1) -#define USBHS_EP1_R_EN (1 << 17) - -#define USBHS_EP2_T_EN (1 << 2) -#define USBHS_EP2_R_EN (1 << 18) - -#define USBHS_EP3_T_EN (1 << 3) -#define USBHS_EP3_R_EN (1 << 19) - -#define USBHS_EP4_T_EN (1 << 4) -#define USBHS_EP4_R_EN (1 << 20) - -#define USBHS_EP5_T_EN (1 << 5) -#define USBHS_EP5_R_EN (1 << 21) - -#define USBHS_EP6_T_EN (1 << 6) -#define USBHS_EP6_R_EN (1 << 22) - -#define USBHS_EP7_T_EN (1 << 7) -#define USBHS_EP7_R_EN (1 << 23) - -#define USBHS_EP8_T_EN (1 << 8) -#define USBHS_EP8_R_EN (1 << 24) - -#define USBHS_EP9_T_EN (1 << 9) -#define USBHS_EP9_R_EN (1 << 25) - -#define USBHS_EP10_T_EN (1 << 10) -#define USBHS_EP10_R_EN (1 << 26) - -#define USBHS_EP11_T_EN (1 << 11) -#define USBHS_EP11_R_EN (1 << 27) - -#define USBHS_EP12_T_EN (1 << 12) -#define USBHS_EP12_R_EN (1 << 28) - -#define USBHS_EP13_T_EN (1 << 13) -#define USBHS_EP13_R_EN (1 << 29) - -#define USBHS_EP14_T_EN (1 << 14) -#define USBHS_EP14_R_EN (1 << 30) - -#define USBHS_EP15_T_EN (1 << 15) -#define USBHS_EP15_R_EN (1 << 31) - -//UEP_TYPE -#define USBHS_UEP_TYPE_OFFSET 0x14 -#define USBHS_EP0_T_TYP (1 << 0) -#define USBHS_EP0_R_TYP (1 << 16) - -#define USBHS_EP1_T_TYP (1 << 1) -#define USBHS_EP1_R_TYP (1 << 17) - -#define USBHS_EP2_T_TYP (1 << 2) -#define USBHS_EP2_R_TYP (1 << 18) - -#define USBHS_EP3_T_TYP (1 << 3) -#define USBHS_EP3_R_TYP (1 << 19) - -#define USBHS_EP4_T_TYP (1 << 4) -#define USBHS_EP4_R_TYP (1 << 20) - -#define USBHS_EP5_T_TYP (1 << 5) -#define USBHS_EP5_R_TYP (1 << 21) - -#define USBHS_EP6_T_TYP (1 << 6) -#define USBHS_EP6_R_TYP (1 << 22) - -#define USBHS_EP7_T_TYP (1 << 7) -#define USBHS_EP7_R_TYP (1 << 23) - -#define USBHS_EP8_T_TYP (1 << 8) -#define USBHS_EP8_R_TYP (1 << 24) - -#define USBHS_EP9_T_TYP (1 << 8) -#define USBHS_EP9_R_TYP (1 << 25) - -#define USBHS_EP10_T_TYP (1 << 10) -#define USBHS_EP10_R_TYP (1 << 26) - -#define USBHS_EP11_T_TYP (1 << 11) -#define USBHS_EP11_R_TYP (1 << 27) - -#define USBHS_EP12_T_TYP (1 << 12) -#define USBHS_EP12_R_TYP (1 << 28) - -#define USBHS_EP13_T_TYP (1 << 13) -#define USBHS_EP13_R_TYP (1 << 29) - -#define USBHS_EP14_T_TYP (1 << 14) -#define USBHS_EP14_R_TYP (1 << 30) - -#define USBHS_EP15_T_TYP (1 << 15) -#define USBHS_EP15_R_TYP (1 << 31) - -/* BUF_MOD UEP1~15 */ -#define USBHS_BUF_MOD_OFFSET 0x18 -#define USBHS_EP0_BUF_MOD (1 << 0) -#define USBHS_EP0_ISO_BUF_MOD (1 << 16) - -#define USBHS_EP1_BUF_MOD (1 << 1) -#define USBHS_EP1_ISO_BUF_MOD (1 << 17) - -#define USBHS_EP2_BUF_MOD (1 << 2) -#define USBHS_EP2_ISO_BUF_MOD (1 << 18) - -#define USBHS_EP3_BUF_MOD (1 << 3) -#define USBHS_EP3_ISO_BUF_MOD (1 << 19) - -#define USBHS_EP4_BUF_MOD (1 << 4) -#define USBHS_EP4_ISO_BUF_MOD (1 << 20) - -#define USBHS_EP5_BUF_MOD (1 << 5) -#define USBHS_EP5_ISO_BUF_MOD (1 << 21) - -#define USBHS_EP6_BUF_MOD (1 << 6) -#define USBHS_EP6_ISO_BUF_MOD (1 << 22) - -#define USBHS_EP7_BUF_MOD (1 << 7) -#define USBHS_EP7_ISO_BUF_MOD (1 << 23) - -#define USBHS_EP8_BUF_MOD (1 << 8) -#define USBHS_EP8_ISO_BUF_MOD (1 << 24) - -#define USBHS_EP9_BUF_MOD (1 << 9) -#define USBHS_EP9_ISO_BUF_MOD (1 << 25) - -#define USBHS_EP10_BUF_MOD (1 << 10) -#define USBHS_EP10_ISO_BUF_MOD (1 << 26) - -#define USBHS_EP11_BUF_MOD (1 << 11) -#define USBHS_EP11_ISO_BUF_MOD (1 << 27) - -#define USBHS_EP12_BUF_MOD (1 << 12) -#define USBHS_EP12_ISO_BUF_MOD (1 << 28) - -#define USBHS_EP13_BUF_MOD (1 << 13) -#define USBHS_EP13_ISO_BUF_MOD (1 << 29) - -#define USBHS_EP14_BUF_MOD (1 << 14) -#define USBHS_EP14_ISO_BUF_MOD (1 << 30) - -#define USBHS_EP15_BUF_MOD (1 << 15) -#define USBHS_EP15_ISO_BUF_MOD (1 << 31) -//USBHS_EPn_T_EN USBHS_EPn_R_EN USBHS_EPn_BUF_MOD Description: Arrange from low to high with UEPn_DMA as the starting address -// 0 0 x The endpoint is disabled and the UEPn_*_DMA buffers are not used. -// 1 0 0 The first address of the receive (OUT) buffer is UEPn_RX_DMA -// 1 0 1 RB_UEPn_RX_TOG[0]=0, use buffer UEPn_RX_DMA RB_UEPn_RX_TOG[0]=1, use buffer UEPn_TX_DMA -// 0 1 0 The first address of the transmit (IN) buffer is UEPn_TX_DMA. -// 0 1 1 RB_UEPn_TX_TOG[0]=0, use buffer UEPn_TX_DMA RB_UEPn_TX_TOG[0]=1, use buffer UEPn_RX_DMA - -/* USB0_DMA */ -#define USBHS_UEP0_DMA_OFFSET(n) (0x1C) // endpoint 0 DMA buffer address - -/* USBX_RX_DMA */ -#define USBHS_UEPx_RX_DMA_OFFSET(n) (0x1C + 4 * (n)) // endpoint x DMA buffer address - -#define USBHS_UEPx_TX_DMA_OFFSET(n) (0x58 + 4 * (n)) // endpoint x DMA buffer address - -#define USBHS_UEPx_MAX_LEN_OFFSET(n) (0x98 + 4 * (n)) // endpoint x DMA buffer address - -#define USBHS_UEPx_T_LEN_OFFSET(n) (0xD8 + 4 * (n)) // endpoint x DMA buffer address -#define USBHS_UEPx_TX_CTRL_OFFSET(n) (0xD8 + 4 * (n) + 2) // endpoint x DMA buffer address -#define USBHS_UEPx_RX_CTRL_OFFSET(n) (0xD8 + 4 * (n) + 3) // endpoint x DMA buffer address - -// UEPn_T_LEN -#define USBHS_EP_T_LEN_MASK (0x7FF) - -//UEPn_TX_CTRL -#define USBHS_EP_T_RES_MASK (3 << 0) -#define USBHS_EP_T_RES_ACK (0 << 0) -#define USBHS_EP_T_RES_NYET (1 << 0) -#define USBHS_EP_T_RES_NAK (2 << 0) -#define USBHS_EP_T_RES_STALL (3 << 0) - -#define USBHS_EP_T_TOG_MASK (3 << 3) -#define USBHS_EP_T_TOG_0 (0 << 3) -#define USBHS_EP_T_TOG_1 (1 << 3) -#define USBHS_EP_T_TOG_2 (2 << 3) -#define USBHS_EP_T_TOG_M (3 << 3) - -#define USBHS_EP_T_AUTOTOG (1 << 5) - -//UEPn_RX_CTRL -#define USBHS_EP_R_RES_MASK (3 << 0) -#define USBHS_EP_R_RES_ACK (0 << 0) -#define USBHS_EP_R_RES_NYET (1 << 0) -#define USBHS_EP_R_RES_NAK (2 << 0) -#define USBHS_EP_R_RES_STALL (3 << 0) - -#define USBHS_EP_R_TOG_MASK (3 << 3) -#define USBHS_EP_R_TOG_0 (0 << 3) -#define USBHS_EP_R_TOG_1 (1 << 3) -#define USBHS_EP_R_TOG_2 (2 << 3) -#define USBHS_EP_R_TOG_M (3 << 3) - -#define USBHS_EP_R_AUTOTOG (1 << 5) - -#define USBHS_TOG_MATCH (1 << 6) - -/******************* HOST ******************/ -// USB HOST_CTRL -#define USBHS_SEND_BUS_RESET (1 << 0) -#define USBHS_SEND_BUS_SUSPEND (1 << 1) -#define USBHS_SEND_BUS_RESUME (1 << 2) -#define USBHS_REMOTE_WAKE (1 << 3) -#define USBHS_PHY_SUSPENDM (1 << 4) -#define USBHS_UH_SOFT_FREE (1 << 6) -#define USBHS_SEND_SOF_EN (1 << 7) - -//UH_CONFIG -#define USBHS_HOST_TX_EN (1 << 3) -#define USBHS_HOST_RX_EN (1 << 18) - -// HOST_EP_TYPE -#define USBHS_ENDP_TX_ISO (1 << 3) -#define USBHS_ENDP_RX_ISO (1 << (16 + 2)) - -// R32_UH_EP_PID -#define USBHS_HOST_MASK_TOKEN (0x0f) -#define USBHS_HOST_MASK_ENDP (0x0f << 4) - -//R8_UH_RX_CTRL -#define USBHS_EP_R_RES_MASK (3 << 0) -#define USBHS_EP_R_RES_ACK (0 << 0) -#define USBHS_EP_R_RES_NYET (1 << 0) -#define USBHS_EP_R_RES_NAK (2 << 0) -#define USBHS_EP_R_RES_STALL (3 << 0) - -#define USBHS_UH_R_RES_NO (1 << 2) -#define USBHS_UH_R_TOG_1 (1 << 3) -#define USBHS_UH_R_TOG_2 (2 << 3) -#define USBHS_UH_R_TOG_3 (3 << 3) -#define USBHS_UH_R_TOG_AUTO (1 << 5) -#define USBHS_UH_R_DATA_NO (1 << 6) -//R8_UH_TX_CTRL -#define USBHS_UH_T_RES_MASK (3 << 0) -#define USBHS_UH_T_RES_ACK (0 << 0) -#define USBHS_UH_T_RES_NYET (1 << 0) -#define USBHS_UH_T_RES_NAK (2 << 0) -#define USBHS_UH_T_RES_STALL (3 << 0) - -#define USBHS_UH_T_RES_NO (1 << 2) -#define USBHS_UH_T_TOG_1 (1 << 3) -#define USBHS_UH_T_TOG_2 (2 << 3) -#define USBHS_UH_T_TOG_3 (3 << 3) -#define USBHS_UH_T_TOG_AUTO (1 << 5) -#define USBHS_UH_T_DATA_NO (1 << 6) - -// 00: OUT, 01:SOF, 10:IN, 11:SETUP -#define PID_OUT 0 -#define PID_SOF 1 -#define PID_IN 2 -#define PID_SETUP 3 - -#endif diff --git a/src/portable/wch/ch32v307/dcd_usbhs.c b/src/portable/wch/ch32v307/dcd_usbhs.c deleted file mode 100644 index 3ad011cff..000000000 --- a/src/portable/wch/ch32v307/dcd_usbhs.c +++ /dev/null @@ -1,391 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2022 Greg Davill - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "tusb_option.h" - -#if CFG_TUD_ENABLED && (CFG_TUSB_MCU == OPT_MCU_CH32V307) -#include "device/dcd.h" - -#include "ch32_usbhs_reg.h" -#include "core_riscv.h" - -// Max number of bi-directional endpoints including EP0 -#define EP_MAX 16 - -typedef struct { - uint8_t *buffer; - // tu_fifo_t * ff; // TODO support dcd_edpt_xfer_fifo API - uint16_t total_len; - uint16_t queued_len; - uint16_t max_size; - bool short_packet; -} xfer_ctl_t; - -#define XFER_CTL_BASE(_ep, _dir) &xfer_status[_ep][_dir] -static xfer_ctl_t xfer_status[EP_MAX][2]; - -#define EP_TX_LEN(ep) *(volatile uint16_t *)((volatile uint16_t *)&(USBHSD->UEP0_TX_LEN) + (ep)*2) -#define EP_TX_CTRL(ep) *(volatile uint8_t *)((volatile uint8_t *)&(USBHSD->UEP0_TX_CTRL) + (ep)*4) -#define EP_RX_CTRL(ep) *(volatile uint8_t *)((volatile uint8_t *)&(USBHSD->UEP0_RX_CTRL) + (ep)*4) -#define EP_RX_MAX_LEN(ep) *(volatile uint16_t *)((volatile uint16_t *)&(USBHSD->UEP0_MAX_LEN) + (ep)*2) - -#define EP_TX_DMA_ADDR(ep) *(volatile uint32_t *)((volatile uint32_t *)&(USBHSD->UEP1_TX_DMA) + (ep - 1)) -#define EP_RX_DMA_ADDR(ep) *(volatile uint32_t *)((volatile uint32_t *)&(USBHSD->UEP1_RX_DMA) + (ep - 1)) - -/* Endpoint Buffer */ -TU_ATTR_ALIGNED(4) uint8_t EP0_DatabufHD[64]; // ep0(64) - -volatile uint8_t USBHS_Dev_Endp0_Tog = 0x01; - -void dcd_init(uint8_t rhport) { - (void)rhport; - - memset(&xfer_status, 0, sizeof(xfer_status)); - - USBHSD->HOST_CTRL = 0x00; - USBHSD->HOST_CTRL = USBHS_PHY_SUSPENDM; - - USBHSD->CONTROL = 0; - -#if TUD_OPT_HIGH_SPEED - USBHSD->CONTROL = USBHS_DMA_EN | USBHS_INT_BUSY_EN | USBHS_HIGH_SPEED; -#else - #error OPT_MODE_FULL_SPEED not currently supported on CH32V307 - USBHSD->CONTROL = USBHS_DMA_EN | USBHS_INT_BUSY_EN | USBHS_FULL_SPEED; -#endif - - USBHSD->INT_EN = 0; - USBHSD->INT_EN = USBHS_SETUP_ACT_EN | USBHS_TRANSFER_EN | USBHS_DETECT_EN | USBHS_SUSPEND_EN; - - /* ALL endpoint enable */ - USBHSD->ENDP_CONFIG = 0xffffffff; - - USBHSD->ENDP_CONFIG = USBHS_EP0_T_EN | USBHS_EP0_R_EN; - USBHSD->ENDP_TYPE = 0x00; - USBHSD->BUF_MODE = 0x00; - - USBHSD->UEP0_MAX_LEN = 64; - - USBHSD->UEP0_DMA = (uint32_t)EP0_DatabufHD; - - USBHSD->UEP0_TX_LEN = 0; - USBHSD->UEP0_TX_CTRL = USBHS_EP_T_RES_NAK; - USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_ACK; - - for (int ep = 1; ep < EP_MAX; ep++) { - EP_TX_LEN(ep) = 0; - EP_TX_CTRL(ep) = USBHS_EP_T_AUTOTOG | USBHS_EP_T_RES_NAK; - EP_RX_CTRL(ep) = USBHS_EP_R_AUTOTOG | USBHS_EP_R_RES_NAK; - - EP_RX_MAX_LEN(ep) = 512; - } - - USBHSD->DEV_AD = 0; - USBHSD->CONTROL |= USBHS_DEV_PU_EN; -} - -void dcd_int_enable(uint8_t rhport) { - (void)rhport; - - NVIC_EnableIRQ(USBHS_IRQn); -} - -void dcd_int_disable(uint8_t rhport) { - (void)rhport; - - NVIC_DisableIRQ(USBHS_IRQn); -} - -void dcd_edpt_close_all(uint8_t rhport) { - (void)rhport; -} - -void dcd_set_address(uint8_t rhport, uint8_t dev_addr) { - (void)dev_addr; - - // Response with zlp status - dcd_edpt_xfer(rhport, 0x80, NULL, 0); -} - -void dcd_remote_wakeup(uint8_t rhport) -{ - (void) rhport; -} - -void dcd_edpt0_status_complete(uint8_t rhport, tusb_control_request_t const *request) { - (void)rhport; - - if (request->bmRequestType_bit.recipient == TUSB_REQ_RCPT_DEVICE && - request->bmRequestType_bit.type == TUSB_REQ_TYPE_STANDARD && - request->bRequest == TUSB_REQ_SET_ADDRESS) { - USBHSD->DEV_AD = (uint8_t)request->wValue; - } - - EP_TX_CTRL(0) = USBHS_EP_T_RES_NAK; - EP_RX_CTRL(0) = USBHS_EP_R_RES_ACK; -} - -bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const *desc_edpt) { - (void)rhport; - - uint8_t const epnum = tu_edpt_number(desc_edpt->bEndpointAddress); - uint8_t const dir = tu_edpt_dir(desc_edpt->bEndpointAddress); - - TU_ASSERT(epnum < EP_MAX); - - xfer_ctl_t *xfer = XFER_CTL_BASE(epnum, dir); - xfer->max_size = tu_edpt_packet_size(desc_edpt); - - if (epnum != 0) { - if (tu_edpt_dir(desc_edpt->bEndpointAddress) == TUSB_DIR_OUT) { - EP_RX_CTRL(epnum) = USBHS_EP_R_AUTOTOG | USBHS_EP_R_RES_ACK; - } else { - EP_TX_LEN(epnum) = 0; - EP_TX_CTRL(epnum) = USBHS_EP_T_AUTOTOG | USBHS_EP_T_RES_NAK | USBHS_EP_T_TOG_0; - } - } - - return true; -} - -int usbd_ep_close(const uint8_t ep) { - (void)ep; - - return 0; -} -void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { - (void)rhport; - - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - if (epnum == 0) { - if (dir == TUSB_DIR_OUT) { - USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_STALL; - } else { - USBHSD->UEP0_TX_LEN = 0; - USBHSD->UEP0_TX_CTRL = USBHS_EP_T_RES_STALL; - } - } else { - if (dir == TUSB_DIR_OUT) { - EP_RX_CTRL(epnum) = (EP_RX_CTRL(epnum) & ~USBHS_EP_R_RES_MASK) | USBHS_EP_R_RES_STALL; - - } else { - EP_TX_CTRL(epnum) = (EP_TX_CTRL(epnum) & ~USBHS_EP_T_RES_MASK) | USBHS_EP_T_RES_STALL; - } - } -} - -void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { - (void)rhport; - - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - if (epnum == 0) { - if (dir == TUSB_DIR_OUT) { - USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_ACK; - } else { - } - } else { - if (dir == TUSB_DIR_OUT) { - EP_RX_CTRL(epnum) = (EP_RX_CTRL(epnum) & ~(USBHS_EP_R_RES_MASK | USBHS_EP_T_TOG_MASK)) | USBHS_EP_T_RES_ACK; - - } else { - EP_TX_CTRL(epnum) = (EP_TX_CTRL(epnum) & ~(USBHS_EP_T_RES_MASK | USBHS_EP_T_TOG_MASK)) | USBHS_EP_T_RES_NAK; - } - } -} - -bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_t total_bytes) { - (void)rhport; - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - xfer_ctl_t *xfer = XFER_CTL_BASE(epnum, dir); - xfer->buffer = buffer; - // xfer->ff = NULL; // TODO support dcd_edpt_xfer_fifo API - xfer->total_len = total_bytes; - xfer->queued_len = 0; - xfer->short_packet = false; - - // uint16_t num_packets = (total_bytes / xfer->max_size); - uint16_t short_packet_size = total_bytes % (xfer->max_size + 1); - - // Zero-size packet is special case. - if (short_packet_size == 0 || (total_bytes == 0)) { - xfer->short_packet = true; - } - - if (tu_edpt_dir(ep_addr) == TUSB_DIR_IN) { - if (!total_bytes) { - xfer->short_packet = true; - if (epnum == 0) { - USBHSD->UEP0_TX_LEN = 0; - USBHSD->UEP0_TX_CTRL = USBHS_EP_T_RES_ACK | (USBHS_Dev_Endp0_Tog ? USBHS_EP_T_TOG_1 : USBHS_EP_T_TOG_0); - USBHS_Dev_Endp0_Tog ^= 1; - } else { - EP_TX_LEN(epnum) = 0; - EP_TX_CTRL(epnum) = (EP_TX_CTRL(epnum) & ~(USBHS_EP_T_RES_MASK)) | USBHS_EP_T_RES_ACK; - } - } else { - if (epnum == 0) { - xfer->queued_len += short_packet_size; - memcpy(&EP0_DatabufHD[0], buffer, short_packet_size); - - USBHSD->UEP0_TX_LEN = short_packet_size; - USBHSD->UEP0_TX_CTRL = USBHS_EP_T_RES_ACK | (USBHS_Dev_Endp0_Tog ? USBHS_EP_T_TOG_1 : USBHS_EP_T_TOG_0); - USBHS_Dev_Endp0_Tog ^= 1; - } else { - xfer->queued_len += short_packet_size; - - EP_TX_DMA_ADDR(epnum) = (uint32_t)buffer; - USBHSD->ENDP_CONFIG |= (USBHS_EP0_T_EN << epnum); - EP_TX_LEN(epnum) = short_packet_size; - EP_TX_CTRL(epnum) = (EP_TX_CTRL(epnum) & ~(USBHS_EP_T_RES_MASK)) | USBHS_EP_T_RES_ACK; - } - } - } else { /* TUSB_DIR_OUT */ - if (epnum == 0) { - uint32_t read_count = USBHSD->RX_LEN; - read_count = TU_MIN(read_count, total_bytes); - - if ((total_bytes == 8)) { - read_count = 8; - memcpy(buffer, &EP0_DatabufHD[0], 8); - } else { - memcpy(buffer, &EP0_DatabufHD[0], read_count); - } - } else { - EP_RX_DMA_ADDR(epnum) = (uint32_t)xfer->buffer; - USBHSD->ENDP_CONFIG |= (USBHS_EP0_R_EN << epnum); - } - - // usbd_ep_read(ep_addr, buffer, total_bytes, &ret_bytes); - } - return true; -} - - -static void receive_packet(xfer_ctl_t *xfer, uint16_t xfer_size) { - // xfer->queued_len = xfer->total_len - remaining; - - uint16_t remaining = xfer->total_len - xfer->queued_len; - uint16_t to_recv_size; - - if (remaining <= xfer->max_size) { - // Avoid buffer overflow. - to_recv_size = (xfer_size > remaining) ? remaining : xfer_size; - } else { - // Room for full packet, choose recv_size based on what the microcontroller - // claims. - to_recv_size = (xfer_size > xfer->max_size) ? xfer->max_size : xfer_size; - } - - if (to_recv_size) { - } - - xfer->queued_len += xfer_size; - - // Per USB spec, a short OUT packet (including length 0) is always - // indicative of the end of a transfer (at least for ctl, bulk, int). - xfer->short_packet = (xfer_size < xfer->max_size); -} - -void dcd_int_handler(uint8_t rhport) { - (void)rhport; - - uint32_t end_num, rx_token; - uint8_t intflag = 0; - - intflag = USBHSD->INT_FG; - - if (intflag & USBHS_TRANSFER_FLAG) { - - end_num = (USBHSD->INT_ST) & MASK_UIS_ENDP; - rx_token = (((USBHSD->INT_ST) & MASK_UIS_TOKEN) >> 4) & 0x03; - - uint8_t endp = end_num | (rx_token == PID_IN ? TUSB_DIR_IN_MASK : 0); - - xfer_ctl_t *xfer = XFER_CTL_BASE(end_num, tu_edpt_dir(endp)); - - if (rx_token == PID_OUT) { - uint16_t rx_len = USBHSD->RX_LEN; - - receive_packet(xfer, rx_len); - - if (xfer->short_packet || (xfer->queued_len == xfer->total_len)) { - xfer->short_packet = false; - - dcd_event_xfer_complete(0, endp, xfer->queued_len, XFER_RESULT_SUCCESS, true); - } - - if (end_num == 0) { - USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_ACK | USBHS_EP_R_TOG_0; - } - - } else if (rx_token == PID_IN) { - if (xfer->short_packet || (xfer->queued_len == xfer->total_len)) { - xfer->short_packet = false; - xfer->total_len = 0; - dcd_event_xfer_complete(0, endp, xfer->queued_len, XFER_RESULT_SUCCESS, true); - - EP_TX_CTRL(end_num) = (EP_TX_CTRL(end_num) & ~(USBHS_EP_T_RES_MASK)) | USBHS_EP_T_RES_NAK; - - if (end_num == 0) { - } - } else { - dcd_edpt_xfer(0, endp, xfer->buffer + xfer->queued_len, xfer->total_len - xfer->queued_len); - } - } - - USBHSD->INT_FG = USBHS_TRANSFER_FLAG; /* Clear flag */ - } else if (intflag & USBHS_SETUP_FLAG) { - USBHS_Dev_Endp0_Tog = 1; - dcd_event_setup_received(0, EP0_DatabufHD, true); - - USBHSD->INT_FG = USBHS_SETUP_FLAG; /* Clear flag */ - } else if (intflag & USBHS_DETECT_FLAG) { - USBHS_Dev_Endp0_Tog = 1; - - xfer_status[0][TUSB_DIR_OUT].max_size = 64; - xfer_status[0][TUSB_DIR_IN].max_size = 64; - - dcd_event_bus_reset(0, TUSB_SPEED_HIGH, true); - - USBHSD->DEV_AD = 0; - USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_ACK | USBHS_EP_R_TOG_0; - - USBHSD->INT_FG = USBHS_DETECT_FLAG; /* Clear flag */ - } else if (intflag & USBHS_SUSPEND_FLAG) { - dcd_event_t event = { .rhport = rhport, .event_id = DCD_EVENT_SUSPEND }; - dcd_event_handler(&event, true); - - USBHSD->INT_FG = USBHS_SUSPEND_FLAG; /* Clear flag */ - } -} - -#endif diff --git a/src/portable/wch/dcd_ch32_usbhs.c b/src/portable/wch/dcd_ch32_usbhs.c new file mode 100644 index 000000000..1f1c0b876 --- /dev/null +++ b/src/portable/wch/dcd_ch32_usbhs.c @@ -0,0 +1,391 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2022 Greg Davill + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "tusb_option.h" + +#if CFG_TUD_ENABLED && ((CFG_TUSB_MCU == OPT_MCU_CH32V307) || (CFG_TUSB_MCU == OPT_MCU_CH32F20X)) +#include "device/dcd.h" + +#include "ch32_usbhs_reg.h" + + +// Max number of bi-directional endpoints including EP0 +#define EP_MAX 16 + +typedef struct { + uint8_t *buffer; + // tu_fifo_t * ff; // TODO support dcd_edpt_xfer_fifo API + uint16_t total_len; + uint16_t queued_len; + uint16_t max_size; + bool short_packet; +} xfer_ctl_t; + +#define XFER_CTL_BASE(_ep, _dir) &xfer_status[_ep][_dir] +static xfer_ctl_t xfer_status[EP_MAX][2]; + +#define EP_TX_LEN(ep) *(volatile uint16_t *)((volatile uint16_t *)&(USBHSD->UEP0_TX_LEN) + (ep)*2) +#define EP_TX_CTRL(ep) *(volatile uint8_t *)((volatile uint8_t *)&(USBHSD->UEP0_TX_CTRL) + (ep)*4) +#define EP_RX_CTRL(ep) *(volatile uint8_t *)((volatile uint8_t *)&(USBHSD->UEP0_RX_CTRL) + (ep)*4) +#define EP_RX_MAX_LEN(ep) *(volatile uint16_t *)((volatile uint16_t *)&(USBHSD->UEP0_MAX_LEN) + (ep)*2) + +#define EP_TX_DMA_ADDR(ep) *(volatile uint32_t *)((volatile uint32_t *)&(USBHSD->UEP1_TX_DMA) + (ep - 1)) +#define EP_RX_DMA_ADDR(ep) *(volatile uint32_t *)((volatile uint32_t *)&(USBHSD->UEP1_RX_DMA) + (ep - 1)) + +/* Endpoint Buffer */ +TU_ATTR_ALIGNED(4) uint8_t EP0_DatabufHD[64]; // ep0(64) + +volatile uint8_t USBHS_Dev_Endp0_Tog = 0x01; + +void dcd_init(uint8_t rhport) { + (void)rhport; + + memset(&xfer_status, 0, sizeof(xfer_status)); + + USBHSD->HOST_CTRL = 0x00; + USBHSD->HOST_CTRL = USBHS_PHY_SUSPENDM; + + USBHSD->CONTROL = 0; + +#if TUD_OPT_HIGH_SPEED + USBHSD->CONTROL = USBHS_DMA_EN | USBHS_INT_BUSY_EN | USBHS_HIGH_SPEED; +#else + #error OPT_MODE_FULL_SPEED not currently supported on CH32 + USBHSD->CONTROL = USBHS_DMA_EN | USBHS_INT_BUSY_EN | USBHS_FULL_SPEED; +#endif + + USBHSD->INT_EN = 0; + USBHSD->INT_EN = USBHS_SETUP_ACT_EN | USBHS_TRANSFER_EN | USBHS_DETECT_EN | USBHS_SUSPEND_EN; + + /* ALL endpoint enable */ + USBHSD->ENDP_CONFIG = 0xffffffff; + + USBHSD->ENDP_CONFIG = USBHS_EP0_T_EN | USBHS_EP0_R_EN; + USBHSD->ENDP_TYPE = 0x00; + USBHSD->BUF_MODE = 0x00; + + USBHSD->UEP0_MAX_LEN = 64; + + USBHSD->UEP0_DMA = (uint32_t)EP0_DatabufHD; + + USBHSD->UEP0_TX_LEN = 0; + USBHSD->UEP0_TX_CTRL = USBHS_EP_T_RES_NAK; + USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_ACK; + + for (int ep = 1; ep < EP_MAX; ep++) { + EP_TX_LEN(ep) = 0; + EP_TX_CTRL(ep) = USBHS_EP_T_AUTOTOG | USBHS_EP_T_RES_NAK; + EP_RX_CTRL(ep) = USBHS_EP_R_AUTOTOG | USBHS_EP_R_RES_NAK; + + EP_RX_MAX_LEN(ep) = 512; + } + + USBHSD->DEV_AD = 0; + USBHSD->CONTROL |= USBHS_DEV_PU_EN; +} + +void dcd_int_enable(uint8_t rhport) { + (void)rhport; + + NVIC_EnableIRQ(USBHS_IRQn); +} + +void dcd_int_disable(uint8_t rhport) { + (void)rhport; + + NVIC_DisableIRQ(USBHS_IRQn); +} + +void dcd_edpt_close_all(uint8_t rhport) { + (void)rhport; +} + +void dcd_set_address(uint8_t rhport, uint8_t dev_addr) { + (void)dev_addr; + + // Response with zlp status + dcd_edpt_xfer(rhport, 0x80, NULL, 0); +} + +void dcd_remote_wakeup(uint8_t rhport) +{ + (void) rhport; +} + +void dcd_edpt0_status_complete(uint8_t rhport, tusb_control_request_t const *request) { + (void)rhport; + + if (request->bmRequestType_bit.recipient == TUSB_REQ_RCPT_DEVICE && + request->bmRequestType_bit.type == TUSB_REQ_TYPE_STANDARD && + request->bRequest == TUSB_REQ_SET_ADDRESS) { + USBHSD->DEV_AD = (uint8_t)request->wValue; + } + + EP_TX_CTRL(0) = USBHS_EP_T_RES_NAK; + EP_RX_CTRL(0) = USBHS_EP_R_RES_ACK; +} + +bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const *desc_edpt) { + (void)rhport; + + uint8_t const epnum = tu_edpt_number(desc_edpt->bEndpointAddress); + uint8_t const dir = tu_edpt_dir(desc_edpt->bEndpointAddress); + + TU_ASSERT(epnum < EP_MAX); + + xfer_ctl_t *xfer = XFER_CTL_BASE(epnum, dir); + xfer->max_size = tu_edpt_packet_size(desc_edpt); + + if (epnum != 0) { + if (tu_edpt_dir(desc_edpt->bEndpointAddress) == TUSB_DIR_OUT) { + EP_RX_CTRL(epnum) = USBHS_EP_R_AUTOTOG | USBHS_EP_R_RES_ACK; + } else { + EP_TX_LEN(epnum) = 0; + EP_TX_CTRL(epnum) = USBHS_EP_T_AUTOTOG | USBHS_EP_T_RES_NAK | USBHS_EP_T_TOG_0; + } + } + + return true; +} + +int usbd_ep_close(const uint8_t ep) { + (void)ep; + + return 0; +} +void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { + (void)rhport; + + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); + + if (epnum == 0) { + if (dir == TUSB_DIR_OUT) { + USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_STALL; + } else { + USBHSD->UEP0_TX_LEN = 0; + USBHSD->UEP0_TX_CTRL = USBHS_EP_T_RES_STALL; + } + } else { + if (dir == TUSB_DIR_OUT) { + EP_RX_CTRL(epnum) = (EP_RX_CTRL(epnum) & ~USBHS_EP_R_RES_MASK) | USBHS_EP_R_RES_STALL; + + } else { + EP_TX_CTRL(epnum) = (EP_TX_CTRL(epnum) & ~USBHS_EP_T_RES_MASK) | USBHS_EP_T_RES_STALL; + } + } +} + +void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { + (void)rhport; + + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); + + if (epnum == 0) { + if (dir == TUSB_DIR_OUT) { + USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_ACK; + } else { + } + } else { + if (dir == TUSB_DIR_OUT) { + EP_RX_CTRL(epnum) = (EP_RX_CTRL(epnum) & ~(USBHS_EP_R_RES_MASK | USBHS_EP_T_TOG_MASK)) | USBHS_EP_T_RES_ACK; + + } else { + EP_TX_CTRL(epnum) = (EP_TX_CTRL(epnum) & ~(USBHS_EP_T_RES_MASK | USBHS_EP_T_TOG_MASK)) | USBHS_EP_T_RES_NAK; + } + } +} + +bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t *buffer, uint16_t total_bytes) { + (void)rhport; + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); + + xfer_ctl_t *xfer = XFER_CTL_BASE(epnum, dir); + xfer->buffer = buffer; + // xfer->ff = NULL; // TODO support dcd_edpt_xfer_fifo API + xfer->total_len = total_bytes; + xfer->queued_len = 0; + xfer->short_packet = false; + + // uint16_t num_packets = (total_bytes / xfer->max_size); + uint16_t short_packet_size = total_bytes % (xfer->max_size + 1); + + // Zero-size packet is special case. + if (short_packet_size == 0 || (total_bytes == 0)) { + xfer->short_packet = true; + } + + if (tu_edpt_dir(ep_addr) == TUSB_DIR_IN) { + if (!total_bytes) { + xfer->short_packet = true; + if (epnum == 0) { + USBHSD->UEP0_TX_LEN = 0; + USBHSD->UEP0_TX_CTRL = USBHS_EP_T_RES_ACK | (USBHS_Dev_Endp0_Tog ? USBHS_EP_T_TOG_1 : USBHS_EP_T_TOG_0); + USBHS_Dev_Endp0_Tog ^= 1; + } else { + EP_TX_LEN(epnum) = 0; + EP_TX_CTRL(epnum) = (EP_TX_CTRL(epnum) & ~(USBHS_EP_T_RES_MASK)) | USBHS_EP_T_RES_ACK; + } + } else { + if (epnum == 0) { + xfer->queued_len += short_packet_size; + memcpy(&EP0_DatabufHD[0], buffer, short_packet_size); + + USBHSD->UEP0_TX_LEN = short_packet_size; + USBHSD->UEP0_TX_CTRL = USBHS_EP_T_RES_ACK | (USBHS_Dev_Endp0_Tog ? USBHS_EP_T_TOG_1 : USBHS_EP_T_TOG_0); + USBHS_Dev_Endp0_Tog ^= 1; + } else { + xfer->queued_len += short_packet_size; + + EP_TX_DMA_ADDR(epnum) = (uint32_t)buffer; + USBHSD->ENDP_CONFIG |= (USBHS_EP0_T_EN << epnum); + EP_TX_LEN(epnum) = short_packet_size; + EP_TX_CTRL(epnum) = (EP_TX_CTRL(epnum) & ~(USBHS_EP_T_RES_MASK)) | USBHS_EP_T_RES_ACK; + } + } + } else { /* TUSB_DIR_OUT */ + if (epnum == 0) { + uint32_t read_count = USBHSD->RX_LEN; + read_count = TU_MIN(read_count, total_bytes); + + if ((total_bytes == 8)) { + read_count = 8; + memcpy(buffer, &EP0_DatabufHD[0], 8); + } else { + memcpy(buffer, &EP0_DatabufHD[0], read_count); + } + } else { + EP_RX_DMA_ADDR(epnum) = (uint32_t)xfer->buffer; + USBHSD->ENDP_CONFIG |= (USBHS_EP0_R_EN << epnum); + } + + // usbd_ep_read(ep_addr, buffer, total_bytes, &ret_bytes); + } + return true; +} + + +static void receive_packet(xfer_ctl_t *xfer, uint16_t xfer_size) { + // xfer->queued_len = xfer->total_len - remaining; + + uint16_t remaining = xfer->total_len - xfer->queued_len; + uint16_t to_recv_size; + + if (remaining <= xfer->max_size) { + // Avoid buffer overflow. + to_recv_size = (xfer_size > remaining) ? remaining : xfer_size; + } else { + // Room for full packet, choose recv_size based on what the microcontroller + // claims. + to_recv_size = (xfer_size > xfer->max_size) ? xfer->max_size : xfer_size; + } + + if (to_recv_size) { + } + + xfer->queued_len += xfer_size; + + // Per USB spec, a short OUT packet (including length 0) is always + // indicative of the end of a transfer (at least for ctl, bulk, int). + xfer->short_packet = (xfer_size < xfer->max_size); +} + +void dcd_int_handler(uint8_t rhport) { + (void)rhport; + + uint32_t end_num, rx_token; + uint8_t intflag = 0; + + intflag = USBHSD->INT_FG; + + if (intflag & USBHS_TRANSFER_FLAG) { + + end_num = (USBHSD->INT_ST) & MASK_UIS_ENDP; + rx_token = (((USBHSD->INT_ST) & MASK_UIS_TOKEN) >> 4) & 0x03; + + uint8_t endp = end_num | (rx_token == PID_IN ? TUSB_DIR_IN_MASK : 0); + + xfer_ctl_t *xfer = XFER_CTL_BASE(end_num, tu_edpt_dir(endp)); + + if (rx_token == PID_OUT) { + uint16_t rx_len = USBHSD->RX_LEN; + + receive_packet(xfer, rx_len); + + if (xfer->short_packet || (xfer->queued_len == xfer->total_len)) { + xfer->short_packet = false; + + dcd_event_xfer_complete(0, endp, xfer->queued_len, XFER_RESULT_SUCCESS, true); + } + + if (end_num == 0) { + USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_ACK | USBHS_EP_R_TOG_0; + } + + } else if (rx_token == PID_IN) { + if (xfer->short_packet || (xfer->queued_len == xfer->total_len)) { + xfer->short_packet = false; + xfer->total_len = 0; + dcd_event_xfer_complete(0, endp, xfer->queued_len, XFER_RESULT_SUCCESS, true); + + EP_TX_CTRL(end_num) = (EP_TX_CTRL(end_num) & ~(USBHS_EP_T_RES_MASK)) | USBHS_EP_T_RES_NAK; + + if (end_num == 0) { + } + } else { + dcd_edpt_xfer(0, endp, xfer->buffer + xfer->queued_len, xfer->total_len - xfer->queued_len); + } + } + + USBHSD->INT_FG = USBHS_TRANSFER_FLAG; /* Clear flag */ + } else if (intflag & USBHS_SETUP_FLAG) { + USBHS_Dev_Endp0_Tog = 1; + dcd_event_setup_received(0, EP0_DatabufHD, true); + + USBHSD->INT_FG = USBHS_SETUP_FLAG; /* Clear flag */ + } else if (intflag & USBHS_DETECT_FLAG) { + USBHS_Dev_Endp0_Tog = 1; + + xfer_status[0][TUSB_DIR_OUT].max_size = 64; + xfer_status[0][TUSB_DIR_IN].max_size = 64; + + dcd_event_bus_reset(0, TUSB_SPEED_HIGH, true); + + USBHSD->DEV_AD = 0; + USBHSD->UEP0_RX_CTRL = USBHS_EP_R_RES_ACK | USBHS_EP_R_TOG_0; + + USBHSD->INT_FG = USBHS_DETECT_FLAG; /* Clear flag */ + } else if (intflag & USBHS_SUSPEND_FLAG) { + dcd_event_t event = { .rhport = rhport, .event_id = DCD_EVENT_SUSPEND }; + dcd_event_handler(&event, true); + + USBHSD->INT_FG = USBHS_SUSPEND_FLAG; /* Clear flag */ + } +} + +#endif diff --git a/src/tusb_option.h b/src/tusb_option.h index a41f5a07e..f4b1a1dd4 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -169,6 +169,7 @@ // WCH #define OPT_MCU_CH32V307 2200 ///< WCH CH32V307 +#define OPT_MCU_CH32F20X 2210 ///< WCH CH32F20x // NXP LPC MCX diff --git a/tools/get_deps.py b/tools/get_deps.py index 1fac291a3..af3043e4e 100644 --- a/tools/get_deps.py +++ b/tools/get_deps.py @@ -164,6 +164,9 @@ deps_optional = { 'hw/mcu/wch/ch32v307': ['https://github.com/openwch/ch32v307.git', '17761f5cf9dbbf2dcf665b7c04934188add20082', 'ch32v307'], + 'hw/mcu/wch/ch32f20x': ['https://github.com/openwch/ch32f20x.git', + '77c4095087e5ed2c548ec9058e655d0b8757663b', + 'ch32f20x'], 'lib/CMSIS_5': ['https://github.com/ARM-software/CMSIS_5.git', '20285262657d1b482d132d20d755c8c330d55c1f', 'imxrt kinetis_k32l2 kinetis_kl lpc51 lpc54 lpc55 mcx mm32 msp432e4 nrf ra saml2x' diff --git a/tools/iar_template.ipcf b/tools/iar_template.ipcf index 4919fe7b4..c3683c3d7 100644 --- a/tools/iar_template.ipcf +++ b/tools/iar_template.ipcf @@ -164,8 +164,8 @@ $TUSB_DIR$/src/portable/valentyusb/eptri/dcd_eptri.c - - $TUSB_DIR$/src/portable/wch/ch32v307/dcd_usbhs.c + + $TUSB_DIR$/src/portable/wch/dcd_ch32_usbhs.c $TUSB_DIR$/src/typec/usbc.c -- cgit v1.3.1 From 27a2c8cba4dc7c56509bb3d9b6415a6fe8f638ac Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 18 Oct 2023 18:43:07 +0700 Subject: adding nulceo stm32u5a5, fix clock configure issue dwc2 core stuck at reset --- hw/bsp/stm32u5/boards/stm32u575eval/board.h | 15 +- hw/bsp/stm32u5/boards/stm32u575nucleo/board.h | 15 +- .../boards/stm32u5a5nucleo/STM32U5A5ZJTXQ_FLASH.ld | 167 ++++++++++ hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake | 2 +- hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h | 57 ++-- hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk | 2 +- .../stm32u5a5nucleo/cubemx/stm32u5a5nucleo.ioc | 352 +++++++++++++++++++++ hw/bsp/stm32u5/family.c | 53 +++- src/common/tusb_mcu.h | 13 +- src/portable/synopsys/dwc2/dwc2_stm32.h | 10 +- src/tusb_option.h | 6 +- tools/get_deps.py | 21 +- 12 files changed, 643 insertions(+), 70 deletions(-) create mode 100644 hw/bsp/stm32u5/boards/stm32u5a5nucleo/STM32U5A5ZJTXQ_FLASH.ld create mode 100644 hw/bsp/stm32u5/boards/stm32u5a5nucleo/cubemx/stm32u5a5nucleo.ioc (limited to 'src/portable') diff --git a/hw/bsp/stm32u5/boards/stm32u575eval/board.h b/hw/bsp/stm32u5/boards/stm32u575eval/board.h index 5562b95a8..bd91502af 100644 --- a/hw/bsp/stm32u5/boards/stm32u575eval/board.h +++ b/hw/bsp/stm32u5/boards/stm32u575eval/board.h @@ -55,12 +55,10 @@ extern "C" // RCC Clock //--------------------------------------------------------------------+ -static inline void board_clock_init(void) -{ - - RCC_OscInitTypeDef RCC_OscInitStruct = {0}; - RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; - RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; +static void SystemClock_Config(void) { + RCC_OscInitTypeDef RCC_OscInitStruct = { 0 }; + RCC_ClkInitTypeDef RCC_ClkInitStruct = { 0 }; + RCC_PeriphCLKInitTypeDef PeriphClkInit = { 0 }; /* Enable Power Clock*/ __HAL_RCC_PWR_CLK_ENABLE(); @@ -94,7 +92,8 @@ static inline void board_clock_init(void) /** Initializes the CPU, AHB and APB buses clocks */ - RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_PCLK3; + RCC_ClkInitStruct.ClockType = + RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_PCLK3; RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; @@ -104,6 +103,8 @@ static inline void board_clock_init(void) HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4); } +static void SystemPower_Config(void) { +} #ifdef __cplusplus } diff --git a/hw/bsp/stm32u5/boards/stm32u575nucleo/board.h b/hw/bsp/stm32u5/boards/stm32u575nucleo/board.h index 54a6d4cd7..6d244d418 100644 --- a/hw/bsp/stm32u5/boards/stm32u575nucleo/board.h +++ b/hw/bsp/stm32u5/boards/stm32u575nucleo/board.h @@ -54,12 +54,10 @@ extern "C" // RCC Clock //--------------------------------------------------------------------+ -static inline void board_clock_init(void) -{ - - RCC_OscInitTypeDef RCC_OscInitStruct = {0}; - RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; - RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; +static void SystemClock_Config(void) { + RCC_OscInitTypeDef RCC_OscInitStruct = { 0 }; + RCC_ClkInitTypeDef RCC_ClkInitStruct = { 0 }; + RCC_PeriphCLKInitTypeDef PeriphClkInit = { 0 }; /* Enable Power Clock */ __HAL_RCC_PWR_CLK_ENABLE(); @@ -93,7 +91,8 @@ static inline void board_clock_init(void) /** Initializes the CPU, AHB and APB buses clocks */ - RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_PCLK3; + RCC_ClkInitStruct.ClockType = + RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_PCLK3; RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; @@ -103,6 +102,8 @@ static inline void board_clock_init(void) HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4); } +static void SystemPower_Config(void) { +} #ifdef __cplusplus } diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/STM32U5A5ZJTXQ_FLASH.ld b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/STM32U5A5ZJTXQ_FLASH.ld new file mode 100644 index 000000000..8aa68a6a6 --- /dev/null +++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/STM32U5A5ZJTXQ_FLASH.ld @@ -0,0 +1,167 @@ +/* +****************************************************************************** +** +** File : LinkerScript.ld +** +** Author : STM32CubeIDE +** +** Abstract : Linker script for STM32U5A5xJ Device from STM32U5 series +** 4096Kbytes FLASH +** 2512Kbytes RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** Distribution: The file is distributed as is without any warranty +** of any kind. +** +***************************************************************************** +** @attention +** +** Copyright (c) 2023 STMicroelectronics. +** All rights reserved. +** +** This software is licensed under terms that can be found in the LICENSE file +** in the root directory of this software component. +** If no LICENSE file comes with this software, it is provided AS-IS. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */ + +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Memories definition */ +MEMORY +{ + RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 2496K + SRAM4 (xrw) : ORIGIN = 0x28000000, LENGTH = 16K + FLASH (rx) : ORIGIN = 0x08000000, LENGTH = 4096K +} + +/* Sections */ +SECTIONS +{ + /* The startup code into "FLASH" Rom type memory */ + .isr_vector : + { + KEEP(*(.isr_vector)) /* Startup code */ + } >FLASH + + /* The program code and other data into "FLASH" Rom type memory */ + .text : + { + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data into "FLASH" Rom type memory */ + .rodata : + { + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + } >FLASH + + .ARM.extab : + { + *(.ARM.extab* .gnu.linkonce.armextab.*) + } >FLASH + + .ARM : + { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* Used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections into "RAM" Ram type memory */ + .data : + { + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + *(.RamFunc) /* .RamFunc sections */ + *(.RamFunc*) /* .RamFunc* sections */ + + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + /* Uninitialized data section into "RAM" Ram type memory */ + .bss : + { + /* This is used by the startup in order to initialize the .bss section */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough "RAM" Ram type memory left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + /* Remove information from the compiler libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake index eea16213b..24d4ef95a 100644 --- a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake +++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake @@ -1,7 +1,7 @@ set(MCU_VARIANT stm32u5a5xx) set(JLINK_DEVICE stm32u5a5zj) -set(LD_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/linker/STM32U5A9xx_FLASH.ld) +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32U5A5ZJTXQ_FLASH.ld) function(update_board TARGET) target_compile_definitions(${TARGET} PUBLIC diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h index 54a6d4cd7..37b008727 100644 --- a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h +++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h @@ -54,46 +54,44 @@ extern "C" // RCC Clock //--------------------------------------------------------------------+ -static inline void board_clock_init(void) -{ - - RCC_OscInitTypeDef RCC_OscInitStruct = {0}; - RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; - RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; +static void SystemClock_Config(void) { + RCC_OscInitTypeDef RCC_OscInitStruct = { 0 }; + RCC_ClkInitTypeDef RCC_ClkInitStruct = { 0 }; - /* Enable Power Clock */ __HAL_RCC_PWR_CLK_ENABLE(); + HAL_PWREx_EnableVddA(); /** Configure the main internal regulator output voltage - */ - HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1); + */ + if (HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1) != HAL_OK) { + Error_Handler(); + } /** Initializes the CPU, AHB and APB buses clocks */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48 | RCC_OSCILLATORTYPE_HSI; + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; RCC_OscInitStruct.HSIState = RCC_HSI_ON; - RCC_OscInitStruct.HSI48State = RCC_HSI48_ON; RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT; RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; - RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; RCC_OscInitStruct.PLL.PLLMBOOST = RCC_PLLMBOOST_DIV1; RCC_OscInitStruct.PLL.PLLM = 1; - RCC_OscInitStruct.PLL.PLLN = 10; - RCC_OscInitStruct.PLL.PLLP = 2; + RCC_OscInitStruct.PLL.PLLN = 20; + RCC_OscInitStruct.PLL.PLLP = 8; RCC_OscInitStruct.PLL.PLLQ = 2; - RCC_OscInitStruct.PLL.PLLR = 1; + RCC_OscInitStruct.PLL.PLLR = 2; RCC_OscInitStruct.PLL.PLLRGE = RCC_PLLVCIRANGE_1; RCC_OscInitStruct.PLL.PLLFRACN = 0; - HAL_RCC_OscConfig(&RCC_OscInitStruct); - - PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_CLK48; - PeriphClkInit.IclkClockSelection = RCC_CLK48CLKSOURCE_HSI48; - - HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit); + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + Error_Handler(); + } /** Initializes the CPU, AHB and APB buses clocks - */ - RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 | RCC_CLOCKTYPE_PCLK3; + */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK + | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2 + | RCC_CLOCKTYPE_PCLK3; RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; @@ -103,6 +101,19 @@ static inline void board_clock_init(void) HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4); } +static void SystemPower_Config(void) { + HAL_PWREx_EnableVddIO2(); + + /* + * Switch to SMPS regulator instead of LDO + */ + if (HAL_PWREx_ConfigSupply(PWR_SMPS_SUPPLY) != HAL_OK) { + Error_Handler(); + } +/* USER CODE BEGIN PWR */ +/* USER CODE END PWR */ +} + #ifdef __cplusplus } diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk index 48a4206a6..13025efa6 100644 --- a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk +++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk @@ -2,7 +2,7 @@ CFLAGS += \ -DSTM32U5A5xx \ # All source paths should be relative to the top level. -LD_FILE = ${ST_CMSIS}/Source/Templates/gcc/linker/STM32U5A9xx_FLASH.ld +LD_FILE = ${BOARD_PATH}/STM32U5A5ZJTXQ_FLASH.ld SRC_S += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32u5a5xx.s diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/cubemx/stm32u5a5nucleo.ioc b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/cubemx/stm32u5a5nucleo.ioc new file mode 100644 index 000000000..289734040 --- /dev/null +++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/cubemx/stm32u5a5nucleo.ioc @@ -0,0 +1,352 @@ +#MicroXplorer Configuration settings - do not modify +ADC1.Channel-1\#ChannelRegularConversion=ADC_CHANNEL_2 +ADC1.IPParameters=Rank-1\#ChannelRegularConversion,master,Channel-1\#ChannelRegularConversion,SamplingTime-1\#ChannelRegularConversion,OffsetNumber-1\#ChannelRegularConversion,MonitoredBy-1\#ChannelRegularConversion,NbrOfConversionFlag +ADC1.MonitoredBy-1\#ChannelRegularConversion=__NULL +ADC1.NbrOfConversionFlag=1 +ADC1.OffsetNumber-1\#ChannelRegularConversion=ADC_OFFSET_NONE +ADC1.Rank-1\#ChannelRegularConversion=1 +ADC1.SamplingTime-1\#ChannelRegularConversion=ADC_SAMPLETIME_5CYCLE +ADC1.master=1 +CAD.formats= +CAD.pinconfig= +CAD.provider= +CORTEX_M33_NS.userName=CORTEX_M33 +File.Version=6 +GPDMA1.DIRECTION_GPDMACH0=DMA_MEMORY_TO_PERIPH +GPDMA1.DIRECTION_GPDMACH3=DMA_MEMORY_TO_PERIPH +GPDMA1.IPHANDLE_GPDMACH0-SIMPLEREQUEST_GPDMACH0=__NULL +GPDMA1.IPHANDLE_GPDMACH3-SIMPLEREQUEST_GPDMACH3=__NULL +GPDMA1.IPHANDLE_GPDMACH5-SIMPLEREQUEST_GPDMACH5=__NULL +GPDMA1.IPParameters=IPHANDLE_GPDMACH5-SIMPLEREQUEST_GPDMACH5,REQUEST_GPDMACH5,IPHANDLE_GPDMACH3-SIMPLEREQUEST_GPDMACH3,REQUEST_GPDMACH3,DIRECTION_GPDMACH3,IPHANDLE_GPDMACH0-SIMPLEREQUEST_GPDMACH0,REQUEST_GPDMACH0,DIRECTION_GPDMACH0,SRCINC_GPDMACH0 +GPDMA1.REQUEST_GPDMACH0=GPDMA1_REQUEST_USART1_TX +GPDMA1.REQUEST_GPDMACH3=GPDMA1_REQUEST_UCPD1_TX +GPDMA1.REQUEST_GPDMACH5=GPDMA1_REQUEST_UCPD1_RX +GPDMA1.SRCINC_GPDMACH0=DMA_SINC_INCREMENTED +GPIO.groupedBy=Group By Peripherals +KeepUserPlacement=false +MMTAppReg1.MEMORYMAP.AP=RW_priv_only +MMTAppReg1.MEMORYMAP.AppRegionName=RAM +MMTAppReg1.MEMORYMAP.ContextName=CortexM33 +MMTAppReg1.MEMORYMAP.CoreName=ARM Cortex-M33 +MMTAppReg1.MEMORYMAP.DefaultDataRegion=true +MMTAppReg1.MEMORYMAP.IPParameters=StartAddress,Size,CoreName,DefaultDataRegion,ContextName,Name,AP +MMTAppReg1.MEMORYMAP.Name=RAM +MMTAppReg1.MEMORYMAP.Size=2555904 +MMTAppReg1.MEMORYMAP.StartAddress=0x20000000 +MMTAppReg2.MEMORYMAP.AppRegionName=RAM Reserved Alias Region +MMTAppReg2.MEMORYMAP.CoreName=ARM Cortex-M33 +MMTAppReg2.MEMORYMAP.DefaultDataRegion=false +MMTAppReg2.MEMORYMAP.IPParameters=StartAddress,Size,CoreName,DefaultDataRegion,ReservedRegion,Name +MMTAppReg2.MEMORYMAP.Name=RAM Reserved Alias Region +MMTAppReg2.MEMORYMAP.ReservedRegion=true +MMTAppReg2.MEMORYMAP.Size=2555904 +MMTAppReg2.MEMORYMAP.StartAddress=0x0A000000 +MMTAppReg3.MEMORYMAP.AP=RO_priv_only +MMTAppReg3.MEMORYMAP.AppRegionName=FLASH +MMTAppReg3.MEMORYMAP.Cacheability=WTRA +MMTAppReg3.MEMORYMAP.ContextName=CortexM33 +MMTAppReg3.MEMORYMAP.CoreName=ARM Cortex-M33 +MMTAppReg3.MEMORYMAP.DefaultCodeRegion=true +MMTAppReg3.MEMORYMAP.DefaultDataRegion=false +MMTAppReg3.MEMORYMAP.IPParameters=StartAddress,Size,CoreName,DefaultDataRegion,MemType,ContextName,Name,AP,Cacheability,DefaultCodeRegion +MMTAppReg3.MEMORYMAP.MemType=ROM +MMTAppReg3.MEMORYMAP.Name=FLASH +MMTAppReg3.MEMORYMAP.Size=4194304 +MMTAppReg3.MEMORYMAP.StartAddress=0x08000000 +MMTAppRegionsCount=3 +MMTConfigApplied=false +Mcu.CPN=STM32U5A5ZJT6Q +Mcu.ContextProject=TrustZoneDisabled +Mcu.Family=STM32U5 +Mcu.IP0=ADC1 +Mcu.IP1=CORTEX_M33_NS +Mcu.IP10=UCPD1 +Mcu.IP11=USART1 +Mcu.IP12=USBPD +Mcu.IP13=USBX +Mcu.IP14=USB_OTG_HS +Mcu.IP2=GPDMA1 +Mcu.IP3=ICACHE +Mcu.IP4=MEMORYMAP +Mcu.IP5=NVIC +Mcu.IP6=PWR +Mcu.IP7=RCC +Mcu.IP8=SYS +Mcu.IP9=THREADX +Mcu.IPNb=15 +Mcu.Name=STM32U5A5ZJTxQ +Mcu.Package=LQFP144 +Mcu.Pin0=PH0-OSC_IN (PH0) +Mcu.Pin1=PH1-OSC_OUT (PH1) +Mcu.Pin10=VP_GPDMA1_VS_GPDMACH0 +Mcu.Pin11=VP_GPDMA1_VS_GPDMACH3 +Mcu.Pin12=VP_GPDMA1_VS_GPDMACH5 +Mcu.Pin13=VP_ICACHE_VS_ICACHE +Mcu.Pin14=VP_PWR_VS_DBSignals +Mcu.Pin15=VP_PWR_VS_SECSignals +Mcu.Pin16=VP_PWR_VS_LPOM +Mcu.Pin17=VP_SYS_VS_tim6 +Mcu.Pin18=VP_THREADX_VS_RTOSJjThreadXJjCoreJjDefault +Mcu.Pin19=VP_USBPD_VS_USBPD1 +Mcu.Pin2=PC1 +Mcu.Pin20=VP_USBPD_VS_PD3TYPEC +Mcu.Pin21=VP_USBPD_VS_usbpd_tim2 +Mcu.Pin22=VP_USBPD_VS_usbpd_usb_cohabitation +Mcu.Pin23=VP_USBX_Core_System +Mcu.Pin24=VP_USBX_UX Device CoreStack_HS +Mcu.Pin25=VP_USBX_UX Device Controller_HS +Mcu.Pin26=VP_USBX_UX Device CDC ACM Class_HS +Mcu.Pin27=VP_MEMORYMAP_VS_MEMORYMAP +Mcu.Pin3=PB15 +Mcu.Pin4=PG2 +Mcu.Pin5=PA9 +Mcu.Pin6=PA10 +Mcu.Pin7=PA11 +Mcu.Pin8=PA12 +Mcu.Pin9=PA15 (JTDI) +Mcu.PinsNb=28 +Mcu.ThirdPartyNb=0 +Mcu.UserConstants= +Mcu.UserName=STM32U5A5ZJTxQ +MxCube.Version=6.9.2 +MxDb.Version=DB.6.0.92 +NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false\:false +NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false\:false +NVIC.ForceEnableDMAVector=true +NVIC.GPDMA1_Channel0_IRQn=true\:0\:0\:false\:false\:true\:true\:true\:true\:true +NVIC.GPDMA1_Channel3_IRQn=true\:0\:0\:false\:false\:true\:true\:true\:true\:true +NVIC.GPDMA1_Channel5_IRQn=true\:0\:0\:false\:false\:true\:true\:true\:true\:true +NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false\:false +NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false\:false +NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false\:false +NVIC.OTG_HS_IRQn=true\:7\:0\:true\:false\:true\:false\:true\:true\:true +NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:false\:false\:false\:false\:false +NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4 +NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:false\:false\:false\:false\:false +NVIC.SavedPendsvIrqHandlerGenerated=true +NVIC.SavedSvcallIrqHandlerGenerated=true +NVIC.SavedSystickIrqHandlerGenerated=true +NVIC.SysTick_IRQn=true\:0\:0\:true\:false\:false\:false\:false\:true\:false +NVIC.TIM6_IRQn=true\:15\:0\:false\:false\:true\:false\:false\:true\:true +NVIC.TimeBase=TIM6_IRQn +NVIC.TimeBaseIP=TIM6 +NVIC.UCPD1_IRQn=true\:5\:0\:true\:false\:true\:false\:true\:false\:true +NVIC.USART1_IRQn=true\:6\:0\:true\:false\:true\:false\:true\:true\:true +NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false\:false +PA10.GPIOParameters=GPIO_Speed,GPIO_PuPd +PA10.GPIO_PuPd=GPIO_PULLUP +PA10.GPIO_Speed=GPIO_SPEED_FREQ_HIGH +PA10.Mode=Asynchronous +PA10.Signal=USART1_RX +PA11.GPIOParameters=GPIO_Speed +PA11.GPIO_Speed=GPIO_SPEED_FREQ_LOW +PA11.Mode=Internal_Phy_Device +PA11.Signal=USB_OTG_HS_DM +PA12.GPIOParameters=GPIO_Speed +PA12.GPIO_Speed=GPIO_SPEED_FREQ_LOW +PA12.Mode=Internal_Phy_Device +PA12.Signal=USB_OTG_HS_DP +PA15\ (JTDI).Mode=Sink_AllSignals +PA15\ (JTDI).Signal=UCPD1_CC1 +PA9.GPIOParameters=GPIO_Speed,GPIO_PuPd +PA9.GPIO_PuPd=GPIO_PULLUP +PA9.GPIO_Speed=GPIO_SPEED_FREQ_HIGH +PA9.Mode=Asynchronous +PA9.Signal=USART1_TX +PB15.Mode=Sink_AllSignals +PB15.Signal=UCPD1_CC2 +PC1.Mode=IN2-Single-Ended +PC1.Signal=ADC1_IN2 +PG2.GPIOParameters=GPIO_Label +PG2.GPIO_Label=LED_RED +PG2.Locked=true +PG2.Signal=GPIO_Output +PH0-OSC_IN\ (PH0).Mode=HSE-External-Oscillator +PH0-OSC_IN\ (PH0).Signal=RCC_OSC_IN +PH1-OSC_OUT\ (PH1).Mode=HSE-External-Oscillator +PH1-OSC_OUT\ (PH1).Signal=RCC_OSC_OUT +PWR.IPParameters=PowerMode +PWR.PowerMode=PWR_SMPS_SUPPLY +PinOutPanel.RotationAngle=0 +ProjectManager.AskForMigrate=true +ProjectManager.BackupPrevious=false +ProjectManager.CompilerOptimize=6 +ProjectManager.ComputerToolchain=false +ProjectManager.CoupleFile=false +ProjectManager.CustomerFirmwarePackage= +ProjectManager.DefaultFWLocation=true +ProjectManager.DeletePrevious=true +ProjectManager.DeviceId=STM32U5A5ZJTxQ +ProjectManager.Example=Ux_Device_CDC_ACM +ProjectManager.ExampleSource=MxCubeFw +ProjectManager.FirmwarePackage=STM32Cube FW_U5 V1.3.0 +ProjectManager.FreePins=false +ProjectManager.HalAssertFull=false +ProjectManager.HeapSize=0x200 +ProjectManager.KeepUserCode=true +ProjectManager.LPBAM.generateCode= +ProjectManager.LastFirmware=true +ProjectManager.LibraryCopy=1 +ProjectManager.MainLocation=Core/Src +ProjectManager.NoMain=false +ProjectManager.PreviousToolchain= +ProjectManager.ProjectBuild=false +ProjectManager.ProjectFileName=stm32u5a5nucleo.ioc +ProjectManager.ProjectName=stm32u5a5nucleo +ProjectManager.ProjectStructure= +ProjectManager.RegisterCallBack= +ProjectManager.StackSize=0x400 +ProjectManager.TargetToolchain=STM32CubeIDE +ProjectManager.ToolChainLocation= +ProjectManager.UAScriptAfterPath= +ProjectManager.UAScriptBeforePath= +ProjectManager.UnderRoot=false +ProjectManager.functionlistsort=1-SystemClock_Config-RCC-false-HAL-false,2-MX_GPIO_Init-GPIO-false-HAL-true,3-MX_GPDMA1_Init-GPDMA1-false-HAL-true,4-MX_ICACHE_Init-ICACHE-false-HAL-true,5-MX_USART1_UART_Init-USART1-false-HAL-false,6-MX_UCPD1_Init-UCPD1-false-LL-true,7-MX_USB_OTG_HS_PCD_Init-USB_OTG_HS-true-HAL-false,8-MX_USBPD_Init-USBPD-false-HAL-false,9-MX_USBX_Init-USBX-false-HAL-false,10-MX_ADC1_Init-ADC1-false-HAL-true,11-MX_MEMORYMAP_Init-MEMORYMAP-false-HAL-true,0-MX_CORTEX_M33_NS_Init-CORTEX_M33_NS-false-HAL-true,0-MX_PWR_Init-PWR-false-HAL-true +RCC.ADCFreq_Value=16000000 +RCC.ADF1Freq_Value=160000000 +RCC.AHBFreq_Value=160000000 +RCC.APB1Freq_Value=160000000 +RCC.APB1TimFreq_Value=160000000 +RCC.APB2Freq_Value=160000000 +RCC.APB2TimFreq_Value=160000000 +RCC.APB3Freq_Value=160000000 +RCC.CK48Freq_Value=48000000 +RCC.CRSFreq_Value=48000000 +RCC.CortexFreq_Value=160000000 +RCC.DACCLockSelectionVirtual=RCC_DAC1CLKSOURCE_LSI +RCC.DACFreq_Value=32000 +RCC.EPOD_VALUE=16000000 +RCC.FCLKCortexFreq_Value=160000000 +RCC.FDCANFreq_Value=160000000 +RCC.FamilyName=M +RCC.HCLKFreq_Value=160000000 +RCC.HSE_VALUE=16000000 +RCC.HSI48_VALUE=48000000 +RCC.HSI_VALUE=16000000 +RCC.I2C1Freq_Value=160000000 +RCC.I2C2Freq_Value=160000000 +RCC.I2C3Freq_Value=160000000 +RCC.I2C4Freq_Value=160000000 +RCC.I2C5Freq_Value=160000000 +RCC.I2C6Freq_Value=160000000 +RCC.IPParameters=ADCFreq_Value,ADF1Freq_Value,AHBFreq_Value,APB1Freq_Value,APB1TimFreq_Value,APB2Freq_Value,APB2TimFreq_Value,APB3Freq_Value,CK48Freq_Value,CRSFreq_Value,CortexFreq_Value,DACCLockSelectionVirtual,DACFreq_Value,EPOD_VALUE,FCLKCortexFreq_Value,FDCANFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI48_VALUE,HSI_VALUE,I2C1Freq_Value,I2C2Freq_Value,I2C3Freq_Value,I2C4Freq_Value,I2C5Freq_Value,I2C6Freq_Value,LPTIM2Freq_Value,LPUART1Freq_Value,LSCOPinFreq_Value,LSE_VALUE,LSIDIV_VALUE,LSI_VALUE,MCO1PinFreq_Value,MDF1Freq_Value,MSIClockRange,MSI_VALUE,OCTOSPIMFreq_Value,PLL1P,PLL2FRACN,PLL2PoutputFreq_Value,PLL2QoutputFreq_Value,PLL2RoutputFreq_Value,PLL3FRACN,PLL3PoutputFreq_Value,PLL3QoutputFreq_Value,PLL3RoutputFreq_Value,PLLFRACN,PLLN,PLLPoutputFreq_Value,PLLQoutputFreq_Value,PLLRCLKFreq_Value,PLLSourceVirtual,RNGFreq_Value,SAESFreq_Value,SAI1Freq_Value,SAI2Freq_Value,SDMMCFreq_Value,SPI1Freq_Value,SPI2Freq_Value,SPI3Freq_Value,SYSCLKFreq_VALUE,SYSCLKSource,UART4Freq_Value,UART5Freq_Value,USART1Freq_Value,USART2Freq_Value,USART3Freq_Value,USART6Freq_Value,USBPHYCLockSelection,USBPHYFreq_Value,VCOInput2Freq_Value,VCOInput3Freq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VCOPLL2OutputFreq_Value,VCOPLL3OutputFreq_Value +RCC.LPTIM2Freq_Value=160000000 +RCC.LPUART1Freq_Value=160000000 +RCC.LSCOPinFreq_Value=32000 +RCC.LSE_VALUE=32768 +RCC.LSIDIV_VALUE=32000 +RCC.LSI_VALUE=32000 +RCC.MCO1PinFreq_Value=160000000 +RCC.MDF1Freq_Value=160000000 +RCC.MSIClockRange=RCC_MSIRANGE_0 +RCC.MSI_VALUE=48000000 +RCC.OCTOSPIMFreq_Value=160000000 +RCC.PLL1P=8 +RCC.PLL2FRACN=0 +RCC.PLL2PoutputFreq_Value=3096000000 +RCC.PLL2QoutputFreq_Value=3096000000 +RCC.PLL2RoutputFreq_Value=3096000000 +RCC.PLL3FRACN=0 +RCC.PLL3PoutputFreq_Value=3096000000 +RCC.PLL3QoutputFreq_Value=3096000000 +RCC.PLL3RoutputFreq_Value=3096000000 +RCC.PLLFRACN=0 +RCC.PLLN=20 +RCC.PLLPoutputFreq_Value=40000000 +RCC.PLLQoutputFreq_Value=160000000 +RCC.PLLRCLKFreq_Value=160000000 +RCC.PLLSourceVirtual=RCC_PLLSOURCE_HSE +RCC.RNGFreq_Value=48000000 +RCC.SAESFreq_Value=48000000 +RCC.SAI1Freq_Value=3096000000 +RCC.SAI2Freq_Value=3096000000 +RCC.SDMMCFreq_Value=40000000 +RCC.SPI1Freq_Value=160000000 +RCC.SPI2Freq_Value=160000000 +RCC.SPI3Freq_Value=160000000 +RCC.SYSCLKFreq_VALUE=160000000 +RCC.SYSCLKSource=RCC_SYSCLKSOURCE_PLLCLK +RCC.UART4Freq_Value=160000000 +RCC.UART5Freq_Value=160000000 +RCC.USART1Freq_Value=160000000 +RCC.USART2Freq_Value=160000000 +RCC.USART3Freq_Value=160000000 +RCC.USART6Freq_Value=160000000 +RCC.USBPHYCLockSelection=RCC_USBPHYCLKSOURCE_HSE +RCC.USBPHYFreq_Value=16000000 +RCC.VCOInput2Freq_Value=48000000 +RCC.VCOInput3Freq_Value=48000000 +RCC.VCOInputFreq_Value=16000000 +RCC.VCOOutputFreq_Value=320000000 +RCC.VCOPLL2OutputFreq_Value=6192000000 +RCC.VCOPLL3OutputFreq_Value=6192000000 +USART1.IPParameters=VirtualMode-Asynchronous +USART1.VirtualMode-Asynchronous=VM_ASYNC +USBX.BSP.number=1 +USBX.Core_System=1 +USBX.IPParameters=Core_System,UX_Device_CoreStack,UX_Device_Controller,UX_DEVICE_CDC_ACM,USBD_CDCACM_EPIN_ADDR,USBD_CDCACM_EPOUT_HS_MPS,USBD_CDCACM_EPIN_HS_MPS,UX_DEVICE_APP_MEM_POOL_SIZE,USBD_PRODUCT_STRING,UX_SLAVE_REQUEST_DATA_MAX_LENGTH,USBX_DEVICE_SYS_SIZE,USBD_PID,USBD_SERIAL_NUMBER,UX_SLAVE_REQUEST_CONTROL_MAX_LENGTH,USBD_CDCACM_EPINCMD_ADDR,MAX_POWER_IN_MILLI_AMPER +USBX.MAX_POWER_IN_MILLI_AMPER=0 +USBX.USBD_CDCACM_EPINCMD_ADDR=2 +USBX.USBD_CDCACM_EPIN_ADDR=1 +USBX.USBD_CDCACM_EPIN_HS_MPS=512 +USBX.USBD_CDCACM_EPOUT_HS_MPS=512 +USBX.USBD_PID=22336 +USBX.USBD_PRODUCT_STRING=STM32 Virtual ComPort +USBX.USBD_SERIAL_NUMBER=CDC_ACM001 +USBX.USBX_DEVICE_SYS_SIZE=4*1024 +USBX.UX_DEVICE_APP_MEM_POOL_SIZE=8192 +USBX.UX_DEVICE_CDC_ACM=1 +USBX.UX_Device_Controller=1 +USBX.UX_Device_CoreStack=1 +USBX.UX_SLAVE_REQUEST_CONTROL_MAX_LENGTH=256 +USBX.UX_SLAVE_REQUEST_DATA_MAX_LENGTH=512 +USBX0.BSP.STBoard=false +USBX0.BSP.api=Unknown +USBX0.BSP.component= +USBX0.BSP.condition= +USBX0.BSP.instance=USB_OTG_HS +USBX0.BSP.ip=USB_OTG_HS +USBX0.BSP.mode=Device_Only +USBX0.BSP.name=USBDevice +USBX0.BSP.semaphore= +USBX0.BSP.solution=USB_OTG_HS +USB_OTG_HS.IPParameters=VirtualMode +USB_OTG_HS.VirtualMode=Device_HS +VP_GPDMA1_VS_GPDMACH0.Mode=SIMPLEREQUEST_GPDMACH0 +VP_GPDMA1_VS_GPDMACH0.Signal=GPDMA1_VS_GPDMACH0 +VP_GPDMA1_VS_GPDMACH3.Mode=SIMPLEREQUEST_GPDMACH3 +VP_GPDMA1_VS_GPDMACH3.Signal=GPDMA1_VS_GPDMACH3 +VP_GPDMA1_VS_GPDMACH5.Mode=SIMPLEREQUEST_GPDMACH5 +VP_GPDMA1_VS_GPDMACH5.Signal=GPDMA1_VS_GPDMACH5 +VP_ICACHE_VS_ICACHE.Mode=DirectMappedCache +VP_ICACHE_VS_ICACHE.Signal=ICACHE_VS_ICACHE +VP_MEMORYMAP_VS_MEMORYMAP.Mode=CurAppReg +VP_MEMORYMAP_VS_MEMORYMAP.Signal=MEMORYMAP_VS_MEMORYMAP +VP_PWR_VS_DBSignals.Mode=DisableDeadBatterySignals +VP_PWR_VS_DBSignals.Signal=PWR_VS_DBSignals +VP_PWR_VS_LPOM.Mode=PowerOptimisation +VP_PWR_VS_LPOM.Signal=PWR_VS_LPOM +VP_PWR_VS_SECSignals.Mode=Security/Privilege +VP_PWR_VS_SECSignals.Signal=PWR_VS_SECSignals +VP_SYS_VS_tim6.Mode=TIM6 +VP_SYS_VS_tim6.Signal=SYS_VS_tim6 +VP_THREADX_VS_RTOSJjThreadXJjCoreJjDefault.Mode=Core_Default +VP_THREADX_VS_RTOSJjThreadXJjCoreJjDefault.Signal=THREADX_VS_RTOSJjThreadXJjCoreJjDefault +VP_USBPD_VS_PD3TYPEC.Mode=PD3_TypeC +VP_USBPD_VS_PD3TYPEC.Signal=USBPD_VS_PD3TYPEC +VP_USBPD_VS_USBPD1.Mode=USBPD_P0 +VP_USBPD_VS_USBPD1.Signal=USBPD_VS_USBPD1 +VP_USBPD_VS_usbpd_tim2.Mode=TIM2 +VP_USBPD_VS_usbpd_tim2.Signal=USBPD_VS_usbpd_tim2 +VP_USBPD_VS_usbpd_usb_cohabitation.Mode=Enable USB Support +VP_USBPD_VS_usbpd_usb_cohabitation.Signal=USBPD_VS_usbpd_usb_cohabitation +VP_USBX_Core_System.Mode=Core_System +VP_USBX_Core_System.Signal=USBX_Core_System +VP_USBX_UX\ Device\ CDC\ ACM\ Class_HS.Mode=UX_Device_class_CDC_ACM_HS +VP_USBX_UX\ Device\ CDC\ ACM\ Class_HS.Signal=USBX_UX Device CDC ACM Class_HS +VP_USBX_UX\ Device\ Controller_HS.Mode=UX_Device_Controller_HS +VP_USBX_UX\ Device\ Controller_HS.Signal=USBX_UX Device Controller_HS +VP_USBX_UX\ Device\ CoreStack_HS.Mode=UX_Device_CoreStack_HS +VP_USBX_UX\ Device\ CoreStack_HS.Signal=USBX_UX Device CoreStack_HS +board=NUCLEO-U5A5ZJ-Q +boardIOC=true diff --git a/hw/bsp/stm32u5/family.c b/hw/bsp/stm32u5/family.c index ab4194623..16a86cbbb 100644 --- a/hw/bsp/stm32u5/family.c +++ b/hw/bsp/stm32u5/family.c @@ -37,6 +37,9 @@ #pragma GCC diagnostic pop #endif +static void Error_Handler(void) { +} + #include "bsp/board_api.h" #include "board.h" @@ -47,6 +50,10 @@ void OTG_FS_IRQHandler(void) { tud_int_handler(0); } +void OTG_HS_IRQHandler(void) { + tud_int_handler(0); +} + //--------------------------------------------------------------------+ // MACRO TYPEDEF CONSTANT ENUM //--------------------------------------------------------------------+ @@ -54,8 +61,9 @@ void OTG_FS_IRQHandler(void) { UART_HandleTypeDef UartHandle; void board_init(void) { - - board_clock_init(); + // Init clock, implemented in board.h + SystemClock_Config(); + SystemPower_Config(); // Enable All GPIOs clocks __HAL_RCC_GPIOA_CLK_ENABLE(); @@ -75,9 +83,6 @@ void board_init(void) { #if CFG_TUSB_OS == OPT_OS_NONE // 1ms tick timer SysTick_Config(SystemCoreClock / 1000); -#elif CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(OTG_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); #endif GPIO_InitTypeDef GPIO_InitStruct; @@ -135,7 +140,13 @@ void board_init(void) { GPIO_InitStruct.Alternate = GPIO_AF10_USB; HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); -#if defined(OTG_FS_VBUS_SENSE) && OTG_FS_VBUS_SENSE +#ifdef USB_OTG_FS + #if CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(OTG_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + #endif + + #if defined(OTG_FS_VBUS_SENSE) && OTG_FS_VBUS_SENSE // Configure VBUS Pin OTG_FS_VBUS_SENSE GPIO_InitStruct.Pin = GPIO_PIN_9; GPIO_InitStruct.Mode = GPIO_MODE_INPUT; @@ -144,20 +155,44 @@ void board_init(void) { // Enable VBUS sense (B device) via pin PA9 USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; -#else + #else // Disable VBUS sense (B device) via pin PA9 USB_OTG_FS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; // B-peripheral session valid override enable USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; -#endif // vbus sense + #endif // vbus sense /* Enable USB power on Pwrctrl CR2 register */ HAL_PWREx_EnableVddUSB(); - /* USB_OTG_FS clock enable */ + /* USB clock enable */ __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); +#else + // STM59x/Ax/Fx/Gx only have 1 USB HS port + + #if CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(OTG_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + #endif + + + // Disable VBUS sense (B device) + USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // B-peripheral session valid override enable + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; + USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + + /* Enable USB power on Pwrctrl CR2 register */ + HAL_PWREx_EnableVddUSB(); + + /* USB clock enable */ + __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); +#endif // USB_OTG_FS + + } //--------------------------------------------------------------------+ diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 8807ff8aa..1797f0bc4 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -217,9 +217,7 @@ // TypeC controller #define TUP_USBIP_TYPEC_STM32 - #define TUP_DCD_ENDPOINT_MAX 8 - #define TUP_TYPEC_RHPORTS_NUM 1 #elif TU_CHECK_MCU(OPT_MCU_STM32G0) @@ -261,14 +259,21 @@ #elif TU_CHECK_MCU(OPT_MCU_STM32U5) #define TUP_USBIP_DWC2 #define TUP_USBIP_DWC2_STM32 - #define TUP_DCD_ENDPOINT_MAX 6 + + // U59x/5Ax/5Fx/5Gx are highspeed with built-in HS PHY + #if defined(STM32U595xx) || defined(STM32U599xx) || defined(STM32U5A5xx) || defined(STM32U5A9xx) || \ + defined(STM32U5F7xx) || defined(STM32U5F9xx) || defined(STM32U5G7xx) || defined(STM32U5G9xx) + #define TUP_DCD_ENDPOINT_MAX 9 + #define TUP_RHPORT_HIGHSPEED 1 + #else + #define TUP_DCD_ENDPOINT_MAX 6 + #endif #elif TU_CHECK_MCU(OPT_MCU_STM32L5) #define TUP_USBIP_FSDEV #define TUP_USBIP_FSDEV_STM32 #define TUP_DCD_ENDPOINT_MAX 8 - //--------------------------------------------------------------------+ // Sony //--------------------------------------------------------------------+ diff --git a/src/portable/synopsys/dwc2/dwc2_stm32.h b/src/portable/synopsys/dwc2/dwc2_stm32.h index aa77511fa..a97a10223 100644 --- a/src/portable/synopsys/dwc2/dwc2_stm32.h +++ b/src/portable/synopsys/dwc2/dwc2_stm32.h @@ -86,18 +86,16 @@ #include "stm32u5xx.h" // NOTE: STM595/5A5/599/5A9 only have 1 USB port (with integrated HS PHY) // USB_OTG_FS_BASE and OTG_FS_IRQn not defined - #if (! defined USB_OTG_FS) + #if !defined(USB_OTG_FS) #define USB_OTG_HS_PERIPH_BASE USB_OTG_HS_BASE #define EP_MAX_HS 9 #define EP_FIFO_SIZE_HS 4096 - #define USB_OTG_FS_PERIPH_BASE USB_OTG_HS_BASE - #define OTG_FS_IRQn OTG_HS_IRQn + //#define OTG_FS_IRQn OTG_HS_IRQn #else #define USB_OTG_FS_PERIPH_BASE USB_OTG_FS_BASE + #define EP_MAX_FS 6 + #define EP_FIFO_SIZE_FS 1280 #endif - #define EP_MAX_FS 6 - #define EP_FIFO_SIZE_FS 1280 - #else #error "Unsupported MCUs" #endif diff --git a/src/tusb_option.h b/src/tusb_option.h index a41f5a07e..a29eb8a3a 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -174,10 +174,10 @@ // NXP LPC MCX #define OPT_MCU_MCXN9 2300 ///< NXP MCX N9 Series -// Helper to check if configured MCU is one of listed +// Check if configured MCU is one of listed // Apply _TU_CHECK_MCU with || as separator to list of input -#define _TU_CHECK_MCU(_m) (CFG_TUSB_MCU == _m) -#define TU_CHECK_MCU(...) (TU_ARGS_APPLY(_TU_CHECK_MCU, ||, __VA_ARGS__)) +#define _TU_CHECK_MCU(_m) (CFG_TUSB_MCU == _m) +#define TU_CHECK_MCU(...) (TU_ARGS_APPLY(_TU_CHECK_MCU, ||, __VA_ARGS__)) //--------------------------------------------------------------------+ // Supported OS diff --git a/tools/get_deps.py b/tools/get_deps.py index 9fdefac9d..8f93ca61f 100644 --- a/tools/get_deps.py +++ b/tools/get_deps.py @@ -181,6 +181,10 @@ deps_all = {**deps_mandatory, **deps_optional} TOP = Path(__file__).parent.parent.resolve() +def run_cmd(cmd): + return subprocess.run(cmd, shell=True, stdout=subprocess.PIPE, stderr=subprocess.STDOUT) + + def get_a_dep(d): if d not in deps_all.keys(): print('{} is not found in dependency list') @@ -189,25 +193,24 @@ def get_a_dep(d): commit = deps_all[d][1] families = deps_all[d][2] - print('cloning {} with {}'.format(d, url)) + print(f'cloning {d} with {url}') p = Path(TOP / d) - git_cmd = "git -C {}".format(p) + git_cmd = f"git -C {p}" # Init git deps if not existed if not p.exists(): p.mkdir(parents=True) - subprocess.run("{} init".format(git_cmd), shell=True, stdout=subprocess.PIPE, stderr=subprocess.STDOUT) - subprocess.run("{} remote add origin {}".format(git_cmd, url), shell=True, stdout=subprocess.PIPE, stderr=subprocess.STDOUT) + run_cmd(f"git -C {p} init") + run_cmd(f"git -C {p} remote add origin {url}") # Check if commit is already fetched - result = subprocess.run("{} rev-parse HEAD".format(git_cmd, commit), shell=True, stdout=subprocess.PIPE, stderr=subprocess.STDOUT) + result = run_cmd(f"git -C {p} rev-parse HEAD") head = result.stdout.decode("utf-8").splitlines()[0] - + run_cmd(f"git -C {p} reset --hard") if commit != head: - subprocess.run("{} reset --hard".format(git_cmd, commit), shell=True) - subprocess.run("{} fetch --depth 1 origin {}".format(git_cmd, commit), shell=True) - subprocess.run("{} checkout FETCH_HEAD".format(git_cmd), shell=True, stdout=subprocess.PIPE, stderr=subprocess.STDOUT) + run_cmd(f"git -C {p} fetch --depth 1 origin {commit}") + run_cmd(f"git -C {p} checkout FETCH_HEAD") return 0 -- cgit v1.3.1 From 9cba9a753b2d8a8c06f1dacc5c16d656397f5d79 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 27 Oct 2023 17:40:53 +0700 Subject: update s3 devkitm with max3421 pin following metro s3, check max3421 version to make sure it is valid --- .idea/cmake.xml | 2 +- hw/bsp/espressif/boards/espressif_s3_devkitm/board.h | 6 +++--- src/portable/analog/max3421/hcd_max3421.c | 5 +++-- 3 files changed, 7 insertions(+), 6 deletions(-) (limited to 'src/portable') diff --git a/.idea/cmake.xml b/.idea/cmake.xml index 88e0e27ad..9f17c805c 100644 --- a/.idea/cmake.xml +++ b/.idea/cmake.xml @@ -16,7 +16,7 @@ - + diff --git a/hw/bsp/espressif/boards/espressif_s3_devkitm/board.h b/hw/bsp/espressif/boards/espressif_s3_devkitm/board.h index 4b4151e72..a319fbc61 100644 --- a/hw/bsp/espressif/boards/espressif_s3_devkitm/board.h +++ b/hw/bsp/espressif/boards/espressif_s3_devkitm/board.h @@ -38,9 +38,9 @@ // SPI for USB host shield #define MAX3421_SPI_HOST SPI2_HOST -#define MAX3421_SCK_PIN 36 -#define MAX3421_MOSI_PIN 35 -#define MAX3421_MISO_PIN 37 +#define MAX3421_SCK_PIN 39 +#define MAX3421_MOSI_PIN 42 +#define MAX3421_MISO_PIN 21 #define MAX3421_CS_PIN 15 #define MAX3421_INTR_PIN 14 diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 787c1e511..4665c1b06 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -433,8 +433,9 @@ bool hcd_init(uint8_t rhport) { reg_write(rhport, PINCTL_ADDR, PINCTL_FDUPSPI, false); // V1 is 0x01, V2 is 0x12, V3 is 0x13 -// uint8_t const revision = reg_read(rhport, REVISION_ADDR, false); -// TU_LOG2_HEX(revision); + uint8_t const revision = reg_read(rhport, REVISION_ADDR, false); + TU_ASSERT(revision == 0x01 || revision == 0x12 || revision == 0x13, false); + TU_LOG2_HEX(revision); // reset reg_write(rhport, USBCTL_ADDR, USBCTL_CHIPRES, false); -- cgit v1.3.1 From a4c542a7b4e753997864b129a4d5fd5b9b77f4e3 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 30 Oct 2023 22:21:58 +0700 Subject: addd dwc2_info.py/md update stm32u5a5 board clock & power configure, able to get passed otg clock reset --- hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h | 12 ++ hw/bsp/stm32u5/family.c | 11 +- src/portable/synopsys/dwc2/dwc2_info.md | 54 +++++++++ src/portable/synopsys/dwc2/dwc2_info.py | 158 ++++++++++++++++++++++++++ src/portable/synopsys/dwc2/dwc2_stm32.h | 95 ++++++++-------- src/portable/synopsys/dwc2/dwc2_type.h | 1 + 6 files changed, 278 insertions(+), 53 deletions(-) create mode 100644 src/portable/synopsys/dwc2/dwc2_info.md create mode 100644 src/portable/synopsys/dwc2/dwc2_info.py (limited to 'src/portable') diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h index 37b008727..c4eb94dd8 100644 --- a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h +++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h @@ -99,6 +99,18 @@ static void SystemClock_Config(void) { RCC_ClkInitStruct.APB3CLKDivider = RCC_HCLK_DIV1; HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4); + + // USB Clock + RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; + PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USBPHY; + PeriphClkInit.UsbPhyClockSelection = RCC_USBPHYCLKSOURCE_HSE; + if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) { + Error_Handler(); + } + + /** Set the OTG PHY reference clock selection + */ + HAL_SYSCFG_SetOTGPHYReferenceClockSelection(SYSCFG_OTG_HS_PHY_CLK_SELECT_1); } static void SystemPower_Config(void) { diff --git a/hw/bsp/stm32u5/family.c b/hw/bsp/stm32u5/family.c index 16a86cbbb..3fbc50d93 100644 --- a/hw/bsp/stm32u5/family.c +++ b/hw/bsp/stm32u5/family.c @@ -177,7 +177,6 @@ void board_init(void) { NVIC_SetPriority(OTG_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); #endif - // Disable VBUS sense (B device) USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; @@ -185,11 +184,17 @@ void board_init(void) { USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; + /* USB clock enable */ + __HAL_RCC_SYSCFG_CLK_ENABLE(); + __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); + __HAL_RCC_USBPHYC_CLK_ENABLE(); + /* Enable USB power on Pwrctrl CR2 register */ HAL_PWREx_EnableVddUSB(); + HAL_PWREx_EnableUSBHSTranceiverSupply(); - /* USB clock enable */ - __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); + /*Configuring the SYSCFG registers OTG_HS PHY*/ + HAL_SYSCFG_EnableOTGPHY(SYSCFG_OTG_HS_PHY_ENABLE); #endif // USB_OTG_FS diff --git a/src/portable/synopsys/dwc2/dwc2_info.md b/src/portable/synopsys/dwc2/dwc2_info.md new file mode 100644 index 000000000..2d8ab067f --- /dev/null +++ b/src/portable/synopsys/dwc2/dwc2_info.md @@ -0,0 +1,54 @@ +| | BCM2711 (Pi4) | EFM32GG FullSpeed | ESP32-S2 | STM32F407 Fullspeed | STM32F407 Highspeed | STM32F411 Fullspeed | STM32F412 Fullspeed | STM32F723 Fullspeed | STM32F723 HighSpeed | STM32F767 Fullspeed | STM32H743 Highspeed | STM32L476 Fullspeed | STM32U5A5 Highspeed | GD32VF103 Fullspeed | XMC4500 | +|:----------------------------|:----------------|:--------------------|:-----------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:-----------| +| guid | 0x2708A000 | 0x00000000 | 0x00000000 | 0x00001200 | 0x00001100 | 0x00001200 | 0x00002000 | 0x00003000 | 0x00003100 | 0x00002000 | 0x00002300 | 0x00002000 | 0x00005000 | 0x00001000 | 0x00AEC000 | +| gsnpsid | 0x4F54280A | 0x4F54330A | 0x4F54400A | 0x4F54281A | 0x4F54281A | 0x4F54281A | 0x4F54320A | 0x4F54330A | 0x4F54330A | 0x4F54320A | 0x4F54330A | 0x4F54310A | 0x4F54411A | 0x00000000 | 0x4F54292A | +| ghwcfg1 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | +| ghwcfg2 | 0x228DDD50 | 0x228F5910 | 0x224DD930 | 0x229DCD20 | 0x229ED590 | 0x229DCD20 | 0x229ED520 | 0x229ED520 | 0x229FE1D0 | 0x229ED520 | 0x229FE190 | 0x229ED520 | 0x228FE052 | 0x00000000 | 0x228F5930 | +| - op_mode | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 2 | 0 | 0 | +| - arch | 2 | 2 | 2 | 0 | 2 | 0 | 0 | 0 | 2 | 0 | 2 | 0 | 2 | 0 | 2 | +| - point2point | 0 | 0 | 1 | 1 | 0 | 1 | 1 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | 1 | +| - hs_phy_type | 1 | 0 | 0 | 0 | 2 | 0 | 0 | 0 | 3 | 0 | 2 | 0 | 1 | 0 | 0 | +| - fs_phy_type | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - num_dev_ep | 7 | 6 | 6 | 3 | 5 | 3 | 5 | 5 | 8 | 5 | 8 | 5 | 8 | 0 | 6 | +| - num_host_ch | 7 | 13 | 7 | 7 | 11 | 7 | 11 | 11 | 15 | 11 | 15 | 11 | 15 | 0 | 13 | +| - period_channel_support | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - enable_dynamic_fifo | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - mul_cpu_int | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | +| - reserved21 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - nperiod_tx_q_depth | 2 | 2 | 1 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 0 | 2 | +| - host_period_tx_q_depth | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 0 | 2 | +| - dev_token_q_depth | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 0 | 8 | +| - otg_enable_ic_usb | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| ghwcfg3 | 0x0FF000E8 | 0x01F204E8 | 0x00C804B5 | 0x020001E8 | 0x03F403E8 | 0x020001E8 | 0x0200D1E8 | 0x0200D1E8 | 0x03EED2E8 | 0x0200D1E8 | 0x03B8D2E8 | 0x0200D1E8 | 0x03B882E8 | 0x00000000 | 0x027A01E5 | +| - xfer_size_width | 8 | 8 | 5 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 0 | 5 | +| - packet_size_width | 6 | 6 | 3 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 0 | 6 | +| - otg_enable | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - i2c_enable | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | 1 | +| - vendor_ctrl_itf | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | +| - optional_feature_removed | 0 | 1 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - synch_reset | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - otg_adp_support | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | +| - otg_enable_hsic | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - battery_charger_support | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | +| - lpm_mode | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | +| - total_fifo_size | 4080 | 498 | 200 | 512 | 1012 | 512 | 512 | 512 | 1006 | 512 | 952 | 512 | 952 | 0 | 634 | +| ghwcfg4 | 0x1FF00020 | 0x1BF08030 | 0xD3F0A030 | 0x0FF08030 | 0x17F00030 | 0x0FF08030 | 0x17F08030 | 0x17F08030 | 0x23F00030 | 0x17F08030 | 0xE3F00030 | 0x17F08030 | 0xE2103E30 | 0x00000000 | 0xDBF08030 | +| - num_dev_period_in_ep | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - power_optimized | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - ahb_freq_min | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - hibernation | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - reserved7 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 4 | 0 | 0 | +| - service_interval_mode | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | +| - ipg_isoc_en | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | +| - acg_enable | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | +| - reserved13 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | +| - utmi_phy_data_width | 0 | 2 | 2 | 2 | 0 | 2 | 2 | 2 | 0 | 2 | 0 | 2 | 0 | 0 | 2 | +| - dev_ctrl_ep_num | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - iddg_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - vbus_valid_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - a_valid_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - b_valid_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - dedicated_fifos | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - num_dev_in_eps | 15 | 13 | 9 | 7 | 11 | 7 | 11 | 11 | 1 | 11 | 1 | 11 | 1 | 0 | 13 | +| - dma_desc_enable | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | +| - dma_dynamic | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | diff --git a/src/portable/synopsys/dwc2/dwc2_info.py b/src/portable/synopsys/dwc2/dwc2_info.py new file mode 100644 index 000000000..0af6c4c77 --- /dev/null +++ b/src/portable/synopsys/dwc2/dwc2_info.py @@ -0,0 +1,158 @@ +import click +import ctypes +import pandas as pd + +# hex value for register: guid, gsnpsid, ghwcfg1, ghwcfg2, ghwcfg3, ghwcfg4 +dwc2_reg_list = ['guid', 'gsnpsid', 'ghwcfg1', 'ghwcfg2', 'ghwcfg3', 'ghwcfg4'] +dwc2_reg_value = { + 'BCM2711 (Pi4)': [0x2708A000, 0x4F54280A, 0, 0x228DDD50, 0xFF000E8, 0x1FF00020], + 'EFM32GG FullSpeed': [0, 0x4F54330A, 0, 0x228F5910, 0x1F204E8, 0x1BF08030], + 'ESP32-S2': [0, 0x4F54400A, 0, 0x224DD930, 0xC804B5, 0xD3F0A030], + 'STM32F407 Fullspeed': [0x1200, 0x4F54281A, 0, 0x229DCD20, 0x20001E8, 0xFF08030], + 'STM32F407 Highspeed': [0x1100, 0x4F54281A, 0, 0x229ED590, 0x3F403E8, 0x17F00030], + 'STM32F411 Fullspeed': [0x1200, 0x4F54281A, 0, 0x229DCD20, 0x20001E8, 0xFF08030], + 'STM32F412 Fullspeed': [0x2000, 0x4F54320A, 0, 0x229ED520, 0x200D1E8, 0x17F08030], + 'STM32F723 Fullspeed': [0x3000, 0x4F54330A, 0, 0x229ED520, 0x200D1E8, 0x17F08030], + 'STM32F723 HighSpeed': [0x3100, 0x4F54330A, 0, 0x229FE1D0, 0x3EED2E8, 0x23F00030], + 'STM32F767 Fullspeed': [0x2000, 0x4F54320A, 0, 0x229ED520, 0x200D1E8, 0x17F08030], + 'STM32H743 Highspeed': [0x2300, 0x4F54330A, 0, 0x229FE190, 0x3B8D2E8, 0xE3F00030], # both HS cores + 'STM32L476 Fullspeed': [0x2000, 0x4F54310A, 0, 0x229ED520, 0x200D1E8, 0x17F08030], + 'STM32U5A5 Highspeed': [0x00005000, 0x4F54411A, 0x00000000, 0x228FE052, 0x03B882E8, 0xE2103E30], + 'GD32VF103 Fullspeed': [0x1000, 0, 0, 0, 0, 0], + 'XMC4500': [0xAEC000, 0x4F54292A, 0, 0x228F5930, 0x27A01E5, 0xDBF08030] +} + +# Combine dwc2_info with dwc2_reg_list +# dwc2_info = { +# 'BCM2711 (Pi4)': { +# 'guid': 0x2708A000, +# 'gsnpsid': 0x4F54280A, +# 'ghwcfg1': 0, +# 'ghwcfg2': 0x228DDD50, +# 'ghwcfg3': 0xFF000E8, +# 'ghwcfg4': 0x1FF00020 +# }, +dwc2_info = {key: {field: value for field, value in zip(dwc2_reg_list, values)} for key, values in dwc2_reg_value.items()} + +class GHWCFG2(ctypes.LittleEndianStructure): + _fields_ = [ + ("op_mode", ctypes.c_uint32, 3), + ("arch", ctypes.c_uint32, 2), + ("point2point", ctypes.c_uint32, 1), + ("hs_phy_type", ctypes.c_uint32, 2), + ("fs_phy_type", ctypes.c_uint32, 2), + ("num_dev_ep", ctypes.c_uint32, 4), + ("num_host_ch", ctypes.c_uint32, 4), + ("period_channel_support", ctypes.c_uint32, 1), + ("enable_dynamic_fifo", ctypes.c_uint32, 1), + ("mul_cpu_int", ctypes.c_uint32, 1), + ("reserved21", ctypes.c_uint32, 1), + ("nperiod_tx_q_depth", ctypes.c_uint32, 2), + ("host_period_tx_q_depth", ctypes.c_uint32, 2), + ("dev_token_q_depth", ctypes.c_uint32, 5), + ("otg_enable_ic_usb", ctypes.c_uint32, 1) + ] + + +class GHWCFG3(ctypes.LittleEndianStructure): + _fields_ = [ + ("xfer_size_width", ctypes.c_uint32, 4), + ("packet_size_width", ctypes.c_uint32, 3), + ("otg_enable", ctypes.c_uint32, 1), + ("i2c_enable", ctypes.c_uint32, 1), + ("vendor_ctrl_itf", ctypes.c_uint32, 1), + ("optional_feature_removed", ctypes.c_uint32, 1), + ("synch_reset", ctypes.c_uint32, 1), + ("otg_adp_support", ctypes.c_uint32, 1), + ("otg_enable_hsic", ctypes.c_uint32, 1), + ("battery_charger_support", ctypes.c_uint32, 1), + ("lpm_mode", ctypes.c_uint32, 1), + ("total_fifo_size", ctypes.c_uint32, 16) + ] + + +class GHWCFG4(ctypes.LittleEndianStructure): + _fields_ = [ + ("num_dev_period_in_ep", ctypes.c_uint32, 4), + ("power_optimized", ctypes.c_uint32, 1), + ("ahb_freq_min", ctypes.c_uint32, 1), + ("hibernation", ctypes.c_uint32, 1), + ("reserved7", ctypes.c_uint32, 3), + ("service_interval_mode", ctypes.c_uint32, 1), + ("ipg_isoc_en", ctypes.c_uint32, 1), + ("acg_enable", ctypes.c_uint32, 1), + ("reserved13", ctypes.c_uint32, 1), + ("utmi_phy_data_width", ctypes.c_uint32, 2), + ("dev_ctrl_ep_num", ctypes.c_uint32, 4), + ("iddg_filter_enabled", ctypes.c_uint32, 1), + ("vbus_valid_filter_enabled", ctypes.c_uint32, 1), + ("a_valid_filter_enabled", ctypes.c_uint32, 1), + ("b_valid_filter_enabled", ctypes.c_uint32, 1), + ("dedicated_fifos", ctypes.c_uint32, 1), + ("num_dev_in_eps", ctypes.c_uint32, 4), + ("dma_desc_enable", ctypes.c_uint32, 1), + ("dma_dynamic", ctypes.c_uint32, 1) + ] + + +@click.group() +def cli(): + pass + + +@cli.command() +@click.argument('mcus', nargs=-1) +@click.option('-a', '--all', is_flag=True, help='Print all bit-field values') +def info(mcus, all): + """Print DWC2 register values for given MCU(s)""" + if len(mcus) == 0: + mcus = dwc2_info + + for mcu in mcus: + for entry in dwc2_info: + if mcu.lower() in entry.lower(): + print(f"## {entry}") + for r_name, r_value in dwc2_info[entry].items(): + print(f"{r_name} = 0x{r_value:08X}") + # Print bit-field values + if all and r_name.upper() in globals(): + class_name = globals()[r_name.upper()] + ghwcfg = class_name.from_buffer_copy(r_value.to_bytes(4, byteorder='little')) + for field_name, field_type, _ in class_name._fields_: + print(f" {field_name} = {getattr(ghwcfg, field_name)}") + + +@cli.command() +def render_md(): + """Render dwc2_info to Markdown table""" + # Create an empty list to hold the dictionaries + dwc2_info_list = [] + + #Iterate over the dwc2_info dictionary and extract fields + for device, reg_values in dwc2_info.items(): + entry_dict = {"Device": device} + for r_name, r_value in reg_values.items(): + entry_dict[r_name] = f"0x{r_value:08X}" + # Print bit-field values + if r_name.upper() in globals(): + class_name = globals()[r_name.upper()] + ghwcfg = class_name.from_buffer_copy(r_value.to_bytes(4, byteorder='little')) + for field_name, field_type, _ in class_name._fields_: + entry_dict[f' - {field_name}'] = getattr(ghwcfg, field_name) + + dwc2_info_list.append(entry_dict) + + # Create a Pandas DataFrame from the list of dictionaries + df = pd.DataFrame(dwc2_info_list).set_index('Device') + + # Transpose the DataFrame to switch rows and columns + df = df.T + #print(df) + + # Write the Markdown table to a file + with open('dwc2_info.md', 'w') as md_file: + md_file.write(df.to_markdown()) + + +if __name__ == '__main__': + cli() diff --git a/src/portable/synopsys/dwc2/dwc2_stm32.h b/src/portable/synopsys/dwc2/dwc2_stm32.h index a97a10223..57df4e941 100644 --- a/src/portable/synopsys/dwc2/dwc2_stm32.h +++ b/src/portable/synopsys/dwc2/dwc2_stm32.h @@ -28,7 +28,7 @@ #define _DWC2_STM32_H_ #ifdef __cplusplus - extern "C" { +extern "C" { #endif // EP_MAX : Max number of bi-directional endpoints including EP0 @@ -84,17 +84,15 @@ #elif CFG_TUSB_MCU == OPT_MCU_STM32U5 #include "stm32u5xx.h" - // NOTE: STM595/5A5/599/5A9 only have 1 USB port (with integrated HS PHY) - // USB_OTG_FS_BASE and OTG_FS_IRQn not defined - #if !defined(USB_OTG_FS) + // U59x/5Ax/5Fx/5Gx are highspeed with built-in HS PHY + #ifdef USB_OTG_FS + #define USB_OTG_FS_PERIPH_BASE USB_OTG_FS_BASE + #define EP_MAX_FS 6 + #define EP_FIFO_SIZE_FS 1280 + #else #define USB_OTG_HS_PERIPH_BASE USB_OTG_HS_BASE #define EP_MAX_HS 9 #define EP_FIFO_SIZE_HS 4096 - //#define OTG_FS_IRQn OTG_HS_IRQn - #else - #define USB_OTG_FS_PERIPH_BASE USB_OTG_FS_BASE - #define EP_MAX_FS 6 - #define EP_FIFO_SIZE_FS 1280 #endif #else #error "Unsupported MCUs" @@ -109,15 +107,14 @@ // On STM32 for consistency we associate // - Port0 to OTG_FS, and Port1 to OTG_HS -static const dwc2_controller_t _dwc2_controller[] = -{ -#ifdef USB_OTG_FS_PERIPH_BASE - { .reg_base = USB_OTG_FS_PERIPH_BASE, .irqnum = OTG_FS_IRQn, .ep_count = EP_MAX_FS, .ep_fifo_size = EP_FIFO_SIZE_FS }, -#endif - -#ifdef USB_OTG_HS_PERIPH_BASE - { .reg_base = USB_OTG_HS_PERIPH_BASE, .irqnum = OTG_HS_IRQn, .ep_count = EP_MAX_HS, .ep_fifo_size = EP_FIFO_SIZE_HS }, -#endif +static const dwc2_controller_t _dwc2_controller[] = { + #ifdef USB_OTG_FS_PERIPH_BASE + { .reg_base = USB_OTG_FS_PERIPH_BASE, .irqnum = OTG_FS_IRQn, .ep_count = EP_MAX_FS, .ep_fifo_size = EP_FIFO_SIZE_FS }, + #endif + + #ifdef USB_OTG_HS_PERIPH_BASE + { .reg_base = USB_OTG_HS_PERIPH_BASE, .irqnum = OTG_HS_IRQn, .ep_count = EP_MAX_HS, .ep_fifo_size = EP_FIFO_SIZE_HS }, + #endif }; //--------------------------------------------------------------------+ @@ -128,40 +125,33 @@ static const dwc2_controller_t _dwc2_controller[] = // extern uint32_t SystemCoreClock; TU_ATTR_ALWAYS_INLINE -static inline void dwc2_dcd_int_enable(uint8_t rhport) -{ - NVIC_EnableIRQ((IRQn_Type)_dwc2_controller[rhport].irqnum); +static inline void dwc2_dcd_int_enable(uint8_t rhport) { + NVIC_EnableIRQ((IRQn_Type) _dwc2_controller[rhport].irqnum); } TU_ATTR_ALWAYS_INLINE -static inline void dwc2_dcd_int_disable (uint8_t rhport) -{ - NVIC_DisableIRQ((IRQn_Type)_dwc2_controller[rhport].irqnum); +static inline void dwc2_dcd_int_disable(uint8_t rhport) { + NVIC_DisableIRQ((IRQn_Type) _dwc2_controller[rhport].irqnum); } TU_ATTR_ALWAYS_INLINE -static inline void dwc2_remote_wakeup_delay(void) -{ +static inline void dwc2_remote_wakeup_delay(void) { // try to delay for 1 ms uint32_t count = SystemCoreClock / 1000; - while ( count-- ) __NOP(); + while (count--) __NOP(); } // MCU specific PHY init, called BEFORE core reset -static inline void dwc2_phy_init(dwc2_regs_t * dwc2, uint8_t hs_phy_type) -{ - if ( hs_phy_type == HS_PHY_TYPE_NONE ) - { +static inline void dwc2_phy_init(dwc2_regs_t* dwc2, uint8_t hs_phy_type) { + if (hs_phy_type == HS_PHY_TYPE_NONE) { // Enable on-chip FS PHY dwc2->stm32_gccfg |= STM32_GCCFG_PWRDWN; - }else - { - // Disable FS PHY + } else { + // Disable FS PHY, TODO on U5A5 (dwc2 4.11a) 16th bit is 'Host CDP behavior enable' dwc2->stm32_gccfg &= ~STM32_GCCFG_PWRDWN; // Enable on-chip HS PHY - if (hs_phy_type == HS_PHY_TYPE_UTMI || hs_phy_type == HS_PHY_TYPE_UTMI_ULPI) - { + if (hs_phy_type == HS_PHY_TYPE_UTMI || hs_phy_type == HS_PHY_TYPE_UTMI_ULPI) { #ifdef USB_HS_PHYC // Enable UTMI HS PHY dwc2->stm32_gccfg |= STM32_GCCFG_PHYHSEN; @@ -200,34 +190,39 @@ static inline void dwc2_phy_init(dwc2_regs_t * dwc2, uint8_t hs_phy_type) } // MCU specific PHY update, it is called AFTER init() and core reset -static inline void dwc2_phy_update(dwc2_regs_t * dwc2, uint8_t hs_phy_type) -{ +static inline void dwc2_phy_update(dwc2_regs_t* dwc2, uint8_t hs_phy_type) { // used to set turnaround time for fullspeed, nothing to do in highspeed mode - if ( hs_phy_type == HS_PHY_TYPE_NONE ) - { + if (hs_phy_type == HS_PHY_TYPE_NONE) { // Turnaround timeout depends on the AHB clock dictated by STM32 Reference Manual uint32_t turnaround; - if ( SystemCoreClock >= 32000000u ) + if (SystemCoreClock >= 32000000u) { turnaround = 0x6u; - else if ( SystemCoreClock >= 27500000u ) + } else if (SystemCoreClock >= 27500000u) { turnaround = 0x7u; - else if ( SystemCoreClock >= 24000000u ) + } else if (SystemCoreClock >= 24000000u) { turnaround = 0x8u; - else if ( SystemCoreClock >= 21800000u ) + } else if (SystemCoreClock >= 21800000u) { turnaround = 0x9u; - else if ( SystemCoreClock >= 20000000u ) + } + else if (SystemCoreClock >= 20000000u) { turnaround = 0xAu; - else if ( SystemCoreClock >= 18500000u ) + } + else if (SystemCoreClock >= 18500000u) { turnaround = 0xBu; - else if ( SystemCoreClock >= 17200000u ) + } + else if (SystemCoreClock >= 17200000u) { turnaround = 0xCu; - else if ( SystemCoreClock >= 16000000u ) + } + else if (SystemCoreClock >= 16000000u) { turnaround = 0xDu; - else if ( SystemCoreClock >= 15000000u ) + } + else if (SystemCoreClock >= 15000000u) { turnaround = 0xEu; - else + } + else { turnaround = 0xFu; + } dwc2->gusbcfg = (dwc2->gusbcfg & ~GUSBCFG_TRDT_Msk) | (turnaround << GUSBCFG_TRDT_Pos); } diff --git a/src/portable/synopsys/dwc2/dwc2_type.h b/src/portable/synopsys/dwc2/dwc2_type.h index 3fc979337..6516882da 100644 --- a/src/portable/synopsys/dwc2/dwc2_type.h +++ b/src/portable/synopsys/dwc2/dwc2_type.h @@ -43,6 +43,7 @@ typedef struct #define DWC2_CORE_REV_3_00a 0x4f54300a #define DWC2_CORE_REV_3_10a 0x4f54310a #define DWC2_CORE_REV_4_00a 0x4f54400a +#define DWC2_CORE_REV_4_11a 0x4f54411a #define DWC2_CORE_REV_4_20a 0x4f54420a #define DWC2_FS_IOT_REV_1_00a 0x5531100a #define DWC2_HS_IOT_REV_1_00a 0x5532100a -- cgit v1.3.1 From 305ef5d48a083f2052351a8a325310168c420c0e Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 30 Oct 2023 22:22:27 +0700 Subject: minor space format dwc2 driver --- src/portable/synopsys/dwc2/dcd_dwc2.c | 648 +++++++++++++--------------------- 1 file changed, 237 insertions(+), 411 deletions(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index c6132a1f5..7b50a7d54 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -82,8 +82,8 @@ static TU_ATTR_ALIGNED(4) uint32_t _setup_packet[2]; typedef struct { - uint8_t * buffer; - tu_fifo_t * ff; + uint8_t* buffer; + tu_fifo_t* ff; uint16_t total_len; uint16_t max_size; uint8_t interval; @@ -93,30 +93,27 @@ static xfer_ctl_t xfer_status[DWC2_EP_MAX][2]; #define XFER_CTL_BASE(_ep, _dir) (&xfer_status[_ep][_dir]) // EP0 transfers are limited to 1 packet - larger sizes has to be split -static uint16_t ep0_pending[2]; // Index determines direction as tusb_dir_t type +static uint16_t ep0_pending[2]; // Index determines direction as tusb_dir_t type // TX FIFO RAM allocation so far in words - RX FIFO size is readily available from dwc2->grxfsiz -static uint16_t _allocated_fifo_words_tx; // TX FIFO size in words (IN EPs) -static bool _out_ep_closed; // Flag to check if RX FIFO size needs an update (reduce its size) +static uint16_t _allocated_fifo_words_tx; // TX FIFO size in words (IN EPs) +static bool _out_ep_closed; // Flag to check if RX FIFO size needs an update (reduce its size) // SOF enabling flag - required for SOF to not get disabled in ISR when SOF was enabled by static bool _sof_en; // Calculate the RX FIFO size according to recommendations from reference manual -static inline uint16_t calc_grxfsiz(uint16_t max_ep_size, uint8_t ep_count) -{ - return 15 + 2*(max_ep_size/4) + 2*ep_count; +static inline uint16_t calc_grxfsiz(uint16_t max_ep_size, uint8_t ep_count) { + return 15 + 2 * (max_ep_size / 4) + 2 * ep_count; } -static void update_grxfsiz(uint8_t rhport) -{ - dwc2_regs_t * dwc2 = DWC2_REG(rhport); +static void update_grxfsiz(uint8_t rhport) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const ep_count = _dwc2_controller[rhport].ep_count; // Determine largest EP size for RX FIFO uint16_t max_epsize = 0; - for (uint8_t epnum = 0; epnum < ep_count; epnum++) - { + for (uint8_t epnum = 0; epnum < ep_count; epnum++) { max_epsize = tu_max16(max_epsize, xfer_status[epnum][TUSB_DIR_OUT].max_size); } @@ -125,9 +122,8 @@ static void update_grxfsiz(uint8_t rhport) } // Start of Bus Reset -static void bus_reset(uint8_t rhport) -{ - dwc2_regs_t * dwc2 = DWC2_REG(rhport); +static void bus_reset(uint8_t rhport) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const ep_count = _dwc2_controller[rhport].ep_count; tu_memclr(xfer_status, sizeof(xfer_status)); @@ -139,15 +135,14 @@ static void bus_reset(uint8_t rhport) dwc2->dcfg &= ~DCFG_DAD_Msk; // 1. NAK for all OUT endpoints - for ( uint8_t n = 0; n < ep_count; n++ ) - { + for (uint8_t n = 0; n < ep_count; n++) { dwc2->epout[n].doepctl |= DOEPCTL_SNAK; } // 2. Set up interrupt mask dwc2->daintmsk = TU_BIT(DAINTMSK_OEPM_Pos) | TU_BIT(DAINTMSK_IEPM_Pos); - dwc2->doepmsk = DOEPMSK_STUPM | DOEPMSK_XFRCM; - dwc2->diepmsk = DIEPMSK_TOM | DIEPMSK_XFRCM; + dwc2->doepmsk = DOEPMSK_STUPM | DOEPMSK_XFRCM; + dwc2->diepmsk = DIEPMSK_TOM | DIEPMSK_XFRCM; // "USB Data FIFOs" section in reference manual // Peripheral FIFO architecture @@ -206,36 +201,34 @@ static void bus_reset(uint8_t rhport) _allocated_fifo_words_tx = 16; // Control IN uses FIFO 0 with 64 bytes ( 16 32-bit word ) - dwc2->dieptxf0 = (16 << DIEPTXF0_TX0FD_Pos) | (_dwc2_controller[rhport].ep_fifo_size/4 - _allocated_fifo_words_tx); + dwc2->dieptxf0 = (16 << DIEPTXF0_TX0FD_Pos) | (_dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx); // Fixed control EP0 size to 64 bytes dwc2->epin[0].diepctl &= ~(0x03 << DIEPCTL_MPSIZ_Pos); xfer_status[0][TUSB_DIR_OUT].max_size = 64; - xfer_status[0][TUSB_DIR_IN ].max_size = 64; + xfer_status[0][TUSB_DIR_IN].max_size = 64; dwc2->epout[0].doeptsiz |= (3 << DOEPTSIZ_STUPCNT_Pos); dwc2->gintmsk |= GINTMSK_OEPINT | GINTMSK_IEPINT; } -static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t const dir, uint16_t const num_packets, uint16_t total_bytes) -{ +static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t const dir, uint16_t const num_packets, + uint16_t total_bytes) { (void) rhport; - dwc2_regs_t * dwc2 = DWC2_REG(rhport); + dwc2_regs_t* dwc2 = DWC2_REG(rhport); // EP0 is limited to one packet each xfer // We use multiple transaction of xfer->max_size length to get a whole transfer done - if ( epnum == 0 ) - { - xfer_ctl_t *const xfer = XFER_CTL_BASE(epnum, dir); + if (epnum == 0) { + xfer_ctl_t* const xfer = XFER_CTL_BASE(epnum, dir); total_bytes = tu_min16(ep0_pending[dir], xfer->max_size); ep0_pending[dir] -= total_bytes; } // IN and OUT endpoint xfers are interrupt-driven, we just schedule them here. - if ( dir == TUSB_DIR_IN ) - { + if (dir == TUSB_DIR_IN) { dwc2_epin_t* epin = dwc2->epin; // A full IN transfer (multiple packets, possibly) triggers XFRC. @@ -245,20 +238,16 @@ static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t c epin[epnum].diepctl |= DIEPCTL_EPENA | DIEPCTL_CNAK; // For ISO endpoint set correct odd/even bit for next frame. - if ( (epin[epnum].diepctl & DIEPCTL_EPTYP) == DIEPCTL_EPTYP_0 && (XFER_CTL_BASE(epnum, dir))->interval == 1 ) - { + if ((epin[epnum].diepctl & DIEPCTL_EPTYP) == DIEPCTL_EPTYP_0 && (XFER_CTL_BASE(epnum, dir))->interval == 1) { // Take odd/even bit from frame counter. uint32_t const odd_frame_now = (dwc2->dsts & (1u << DSTS_FNSOF_Pos)); epin[epnum].diepctl |= (odd_frame_now ? DIEPCTL_SD0PID_SEVNFRM_Msk : DIEPCTL_SODDFRM_Msk); } // Enable fifo empty interrupt only if there are something to put in the fifo. - if ( total_bytes != 0 ) - { + if (total_bytes != 0) { dwc2->diepempmsk |= (1 << epnum); } - } - else - { + } else { dwc2_epout_t* epout = dwc2->epout; // A full OUT transfer (multiple packets, possibly) triggers XFRC. @@ -267,9 +256,8 @@ static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t c ((total_bytes << DOEPTSIZ_XFRSIZ_Pos) & DOEPTSIZ_XFRSIZ_Msk); epout[epnum].doepctl |= DOEPCTL_EPENA | DOEPCTL_CNAK; - if ( (epout[epnum].doepctl & DOEPCTL_EPTYP) == DOEPCTL_EPTYP_0 && - XFER_CTL_BASE(epnum, dir)->interval == 1 ) - { + if ((epout[epnum].doepctl & DOEPCTL_EPTYP) == DOEPCTL_EPTYP_0 && + XFER_CTL_BASE(epnum, dir)->interval == 1) { // Take odd/even bit from frame counter. uint32_t const odd_frame_now = (dwc2->dsts & (1u << DSTS_FNSOF_Pos)); epout[epnum].doepctl |= (odd_frame_now ? DOEPCTL_SD0PID_SEVNFRM_Msk : DOEPCTL_SODDFRM_Msk); @@ -281,93 +269,35 @@ static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t c /* Controller API *------------------------------------------------------------------*/ #if CFG_TUSB_DEBUG >= DWC2_DEBUG -void print_dwc2_info(dwc2_regs_t * dwc2) -{ - dwc2_ghwcfg2_t const * hw_cfg2 = &dwc2->ghwcfg2_bm; - dwc2_ghwcfg3_t const * hw_cfg3 = &dwc2->ghwcfg3_bm; - dwc2_ghwcfg4_t const * hw_cfg4 = &dwc2->ghwcfg4_bm; -// TU_LOG_HEX(DWC2_DEBUG, dwc2->gotgctl); -// TU_LOG_HEX(DWC2_DEBUG, dwc2->gusbcfg); -// TU_LOG_HEX(DWC2_DEBUG, dwc2->dcfg); - TU_LOG_HEX(DWC2_DEBUG, dwc2->guid); - TU_LOG_HEX(DWC2_DEBUG, dwc2->gsnpsid); - TU_LOG_HEX(DWC2_DEBUG, dwc2->ghwcfg1); - - // HW configure 2 - TU_LOG(DWC2_DEBUG, "\r\n"); - TU_LOG_HEX(DWC2_DEBUG, dwc2->ghwcfg2); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->op_mode ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->arch ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->point2point ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->hs_phy_type ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->fs_phy_type ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->num_dev_ep ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->num_host_ch ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->period_channel_support ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->enable_dynamic_fifo ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->mul_cpu_int ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->nperiod_tx_q_depth ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->host_period_tx_q_depth ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->dev_token_q_depth ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg2->otg_enable_ic_usb ); - - // HW configure 3 - TU_LOG(DWC2_DEBUG, "\r\n"); - TU_LOG_HEX(DWC2_DEBUG, dwc2->ghwcfg3); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->xfer_size_width ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->packet_size_width ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->otg_enable ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->i2c_enable ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->vendor_ctrl_itf ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->optional_feature_removed ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->synch_reset ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->otg_adp_support ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->otg_enable_hsic ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->battery_charger_support ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->lpm_mode ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg3->total_fifo_size ); - - // HW configure 4 - TU_LOG(DWC2_DEBUG, "\r\n"); - TU_LOG_HEX(DWC2_DEBUG, dwc2->ghwcfg4); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->num_dev_period_in_ep ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->power_optimized ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->ahb_freq_min ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->hibernation ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->service_interval_mode ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->ipg_isoc_en ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->acg_enable ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->utmi_phy_data_width ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->dev_ctrl_ep_num ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->iddg_filter_enabled ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->vbus_valid_filter_enabled ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->a_valid_filter_enabled ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->b_valid_filter_enabled ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->dedicated_fifos ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->num_dev_in_eps ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->dma_desc_enable ); - TU_LOG_INT(DWC2_DEBUG, hw_cfg4->dma_dynamic ); +void print_dwc2_info(dwc2_regs_t* dwc2) { + // print guid, gsnpsid, ghwcfg1, ghwcfg2, ghwcfg3, ghwcfg4 + // use dwc2_info.py/md for bit-field value and comparison with other ports + volatile uint32_t const* p = (volatile uint32_t const*) &dwc2->guid; + TU_LOG(DWC2_DEBUG, "guid, gsnpsid, ghwcfg1, ghwcfg2, ghwcfg3, ghwcfg4\r\n"); + for (size_t i = 0; i < 5; i++) { + TU_LOG(DWC2_DEBUG, "0x%08lX, ", p[i]); + } + TU_LOG(DWC2_DEBUG, "0x%08lX\r\n", p[5]); } + #endif -static void reset_core(dwc2_regs_t * dwc2) -{ +static void reset_core(dwc2_regs_t* dwc2) { // reset core dwc2->grstctl |= GRSTCTL_CSRST; // wait for reset bit is cleared // TODO version 4.20a should wait for RESET DONE mask - while (dwc2->grstctl & GRSTCTL_CSRST) { } + while (dwc2->grstctl & GRSTCTL_CSRST) {} // wait for AHB master IDLE - while ( !(dwc2->grstctl & GRSTCTL_AHBIDL) ) { } + while (!(dwc2->grstctl & GRSTCTL_AHBIDL)) {} // wait for device mode ? } -static bool phy_hs_supported(dwc2_regs_t * dwc2) -{ +static bool phy_hs_supported(dwc2_regs_t* dwc2) { // note: esp32 incorrect report its hs_phy_type as utmi #if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) return false; @@ -376,8 +306,7 @@ static bool phy_hs_supported(dwc2_regs_t * dwc2) #endif } -static void phy_fs_init(dwc2_regs_t * dwc2) -{ +static void phy_fs_init(dwc2_regs_t* dwc2) { TU_LOG(DWC2_DEBUG, "Fullspeed PHY init\r\n"); // Select FS PHY @@ -401,15 +330,13 @@ static void phy_fs_init(dwc2_regs_t * dwc2) dwc2->dcfg = (dwc2->dcfg & ~DCFG_DSPD_Msk) | (DCFG_DSPD_FS << DCFG_DSPD_Pos); } -static void phy_hs_init(dwc2_regs_t * dwc2) -{ +static void phy_hs_init(dwc2_regs_t* dwc2) { uint32_t gusbcfg = dwc2->gusbcfg; // De-select FS PHY gusbcfg &= ~GUSBCFG_PHYSEL; - if (dwc2->ghwcfg2_bm.hs_phy_type == HS_PHY_TYPE_ULPI) - { + if (dwc2->ghwcfg2_bm.hs_phy_type == HS_PHY_TYPE_ULPI) { TU_LOG(DWC2_DEBUG, "Highspeed ULPI PHY init\r\n"); // Select ULPI @@ -423,8 +350,7 @@ static void phy_hs_init(dwc2_regs_t * dwc2) // Disable FS/LS ULPI gusbcfg &= ~(GUSBCFG_ULPIFSLS | GUSBCFG_ULPICSM); - }else - { + } else { TU_LOG(DWC2_DEBUG, "Highspeed UTMI+ PHY init\r\n"); // Select UTMI+ with 8-bit interface @@ -465,8 +391,7 @@ static void phy_hs_init(dwc2_regs_t * dwc2) dwc2->dcfg = dcfg; } -static bool check_dwc2(dwc2_regs_t * dwc2) -{ +static bool check_dwc2(dwc2_regs_t* dwc2) { #if CFG_TUSB_DEBUG >= DWC2_DEBUG print_dwc2_info(dwc2); #endif @@ -481,41 +406,35 @@ static bool check_dwc2(dwc2_regs_t * dwc2) return true; } -void dcd_init (uint8_t rhport) -{ +void dcd_init(uint8_t rhport) { // Programming model begins in the last section of the chapter on the USB // peripheral in each Reference Manual. - dwc2_regs_t * dwc2 = DWC2_REG(rhport); + dwc2_regs_t* dwc2 = DWC2_REG(rhport); // Check Synopsys ID register, failed if controller clock/power is not enabled - TU_VERIFY(check_dwc2(dwc2), ); - + if (!check_dwc2(dwc2)) return; dcd_disconnect(rhport); // max number of endpoints & total_fifo_size are: // hw_cfg2->num_dev_ep, hw_cfg2->total_fifo_size - if( phy_hs_supported(dwc2) ) - { - // Highspeed - phy_hs_init(dwc2); - }else - { - // core does not support highspeed or hs-phy is not present - phy_fs_init(dwc2); + if (phy_hs_supported(dwc2)) { + phy_hs_init(dwc2); // Highspeed + } else { + phy_fs_init(dwc2); // core does not support highspeed or hs phy is not present } // Restart PHY clock dwc2->pcgctl &= ~(PCGCTL_STOPPCLK | PCGCTL_GATEHCLK | PCGCTL_PWRCLMP | PCGCTL_RSTPDWNMODULE); - /* Set HS/FS Timeout Calibration to 7 (max available value). - * The number of PHY clocks that the application programs in - * this field is added to the high/full speed interpacket timeout - * duration in the core to account for any additional delays - * introduced by the PHY. This can be required, because the delay - * introduced by the PHY in generating the linestate condition - * can vary from one PHY to another. - */ + /* Set HS/FS Timeout Calibration to 7 (max available value). + * The number of PHY clocks that the application programs in + * this field is added to the high/full speed interpacket timeout + * duration in the core to account for any additional delays + * introduced by the PHY. This can be required, because the delay + * introduced by the PHY in generating the linestate condition + * can vary from one PHY to another. + */ dwc2->gusbcfg |= (7ul << GUSBCFG_TOCAL_Pos); // Force device mode @@ -537,7 +456,7 @@ void dcd_init (uint8_t rhport) // Required as part of core initialization. // TODO: How should mode mismatch be handled? It will cause // the core to stop working/require reset. - dwc2->gintmsk = GINTMSK_OTGINT | GINTMSK_MMISM | GINTMSK_RXFLVLM | + dwc2->gintmsk = GINTMSK_OTGINT | GINTMSK_MMISM | GINTMSK_RXFLVLM | GINTMSK_USBSUSPM | GINTMSK_USBRST | GINTMSK_ENUMDNEM | GINTMSK_WUIM; // Enable global interrupt @@ -554,30 +473,26 @@ void dcd_init (uint8_t rhport) dcd_connect(rhport); } -void dcd_int_enable (uint8_t rhport) -{ +void dcd_int_enable(uint8_t rhport) { dwc2_dcd_int_enable(rhport); } -void dcd_int_disable (uint8_t rhport) -{ +void dcd_int_disable(uint8_t rhport) { dwc2_dcd_int_disable(rhport); } -void dcd_set_address (uint8_t rhport, uint8_t dev_addr) -{ - dwc2_regs_t * dwc2 = DWC2_REG(rhport); +void dcd_set_address(uint8_t rhport, uint8_t dev_addr) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); dwc2->dcfg = (dwc2->dcfg & ~DCFG_DAD_Msk) | (dev_addr << DCFG_DAD_Pos); // Response with status after changing device address dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_IN), NULL, 0); } -void dcd_remote_wakeup(uint8_t rhport) -{ +void dcd_remote_wakeup(uint8_t rhport) { (void) rhport; - dwc2_regs_t * dwc2 = DWC2_REG(rhport); + dwc2_regs_t* dwc2 = DWC2_REG(rhport); // set remote wakeup dwc2->dctl |= DCTL_RWUSIG; @@ -592,35 +507,29 @@ void dcd_remote_wakeup(uint8_t rhport) dwc2->dctl &= ~DCTL_RWUSIG; } -void dcd_connect(uint8_t rhport) -{ +void dcd_connect(uint8_t rhport) { (void) rhport; - dwc2_regs_t * dwc2 = DWC2_REG(rhport); + dwc2_regs_t* dwc2 = DWC2_REG(rhport); dwc2->dctl &= ~DCTL_SDIS; } -void dcd_disconnect(uint8_t rhport) -{ +void dcd_disconnect(uint8_t rhport) { (void) rhport; - dwc2_regs_t * dwc2 = DWC2_REG(rhport); + dwc2_regs_t* dwc2 = DWC2_REG(rhport); dwc2->dctl |= DCTL_SDIS; } // Be advised: audio, video and possibly other iso-ep classes use dcd_sof_enable() to enable/disable its corresponding ISR on purpose! -void dcd_sof_enable(uint8_t rhport, bool en) -{ +void dcd_sof_enable(uint8_t rhport, bool en) { (void) rhport; - dwc2_regs_t * dwc2 = DWC2_REG(rhport); + dwc2_regs_t* dwc2 = DWC2_REG(rhport); _sof_en = en; - if (en) - { + if (en) { dwc2->gintsts = GINTSTS_SOF; dwc2->gintmsk |= GINTMSK_SOFM; - } - else - { + } else { dwc2->gintmsk &= ~GINTMSK_SOFM; } } @@ -629,33 +538,30 @@ void dcd_sof_enable(uint8_t rhport, bool en) /* DCD Endpoint port *------------------------------------------------------------------*/ -bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) -{ +bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const* desc_edpt) { (void) rhport; - dwc2_regs_t * dwc2 = DWC2_REG(rhport); + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const ep_count = _dwc2_controller[rhport].ep_count; uint8_t const epnum = tu_edpt_number(desc_edpt->bEndpointAddress); - uint8_t const dir = tu_edpt_dir(desc_edpt->bEndpointAddress); + uint8_t const dir = tu_edpt_dir(desc_edpt->bEndpointAddress); TU_ASSERT(epnum < ep_count); - xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, dir); + xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, dir); xfer->max_size = tu_edpt_packet_size(desc_edpt); xfer->interval = desc_edpt->bInterval; uint16_t const fifo_size = tu_div_ceil(xfer->max_size, 4); - if(dir == TUSB_DIR_OUT) - { + if (dir == TUSB_DIR_OUT) { // Calculate required size of RX FIFO - uint16_t const sz = calc_grxfsiz(4*fifo_size, ep_count); + uint16_t const sz = calc_grxfsiz(4 * fifo_size, ep_count); // If size_rx needs to be extended check if possible and if so enlarge it - if (dwc2->grxfsiz < sz) - { - TU_ASSERT(sz + _allocated_fifo_words_tx <= _dwc2_controller[rhport].ep_fifo_size/4); + if (dwc2->grxfsiz < sz) { + TU_ASSERT(sz + _allocated_fifo_words_tx <= _dwc2_controller[rhport].ep_fifo_size / 4); // Enlarge RX FIFO dwc2->grxfsiz = sz; @@ -667,9 +573,7 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) (xfer->max_size << DOEPCTL_MPSIZ_Pos); dwc2->daintmsk |= TU_BIT(DAINTMSK_OEPM_Pos + epnum); - } - else - { + } else { // "USB Data FIFOs" section in reference manual // Peripheral FIFO architecture // @@ -692,15 +596,17 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) // - IN EP 1 gets FIFO 1, IN EP "n" gets FIFO "n". // Check if free space is available - TU_ASSERT(_allocated_fifo_words_tx + fifo_size + dwc2->grxfsiz <= _dwc2_controller[rhport].ep_fifo_size/4); + TU_ASSERT(_allocated_fifo_words_tx + fifo_size + dwc2->grxfsiz <= _dwc2_controller[rhport].ep_fifo_size / 4); _allocated_fifo_words_tx += fifo_size; - TU_LOG(DWC2_DEBUG, " Allocated %u bytes at offset %lu", fifo_size*4, _dwc2_controller[rhport].ep_fifo_size-_allocated_fifo_words_tx*4); + TU_LOG(DWC2_DEBUG, " Allocated %u bytes at offset %lu", fifo_size * 4, + _dwc2_controller[rhport].ep_fifo_size - _allocated_fifo_words_tx * 4); // DIEPTXF starts at FIFO #1. // Both TXFD and TXSA are in unit of 32-bit words. - dwc2->dieptxf[epnum - 1] = (fifo_size << DIEPTXF_INEPTXFD_Pos) | (_dwc2_controller[rhport].ep_fifo_size/4 - _allocated_fifo_words_tx); + dwc2->dieptxf[epnum - 1] = (fifo_size << DIEPTXF_INEPTXFD_Pos) | + (_dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx); dwc2->epin[epnum].diepctl |= (1 << DIEPCTL_USBAEP_Pos) | (epnum << DIEPCTL_TXFNUM_Pos) | @@ -715,16 +621,14 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) } // Close all non-control endpoints, cancel all pending transfers if any. -void dcd_edpt_close_all (uint8_t rhport) -{ - dwc2_regs_t * dwc2 = DWC2_REG(rhport); +void dcd_edpt_close_all(uint8_t rhport) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const ep_count = _dwc2_controller[rhport].ep_count; // Disable non-control interrupt dwc2->daintmsk = (1 << DAINTMSK_OEPM_Pos) | (1 << DAINTMSK_IEPM_Pos); - for(uint8_t n = 1; n < ep_count; n++) - { + for (uint8_t n = 1; n < ep_count; n++) { // disable OUT endpoint dwc2->epout[n].doepctl = 0; xfer_status[n][TUSB_DIR_OUT].max_size = 0; @@ -738,31 +642,27 @@ void dcd_edpt_close_all (uint8_t rhport) _allocated_fifo_words_tx = 16; } -bool dcd_edpt_xfer (uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes) -{ +bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes) { uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); - xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, dir); - xfer->buffer = buffer; - xfer->ff = NULL; - xfer->total_len = total_bytes; + xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, dir); + xfer->buffer = buffer; + xfer->ff = NULL; + xfer->total_len = total_bytes; // EP0 can only handle one packet - if(epnum == 0) - { + if (epnum == 0) { ep0_pending[dir] = total_bytes; // Schedule the first transaction for EP0 transfer edpt_schedule_packets(rhport, epnum, dir, 1, ep0_pending[dir]); - } - else - { + } else { uint16_t num_packets = (total_bytes / xfer->max_size); uint16_t const short_packet_size = total_bytes % xfer->max_size; // Zero-size packet is special case. - if ( (short_packet_size > 0) || (total_bytes == 0) ) num_packets++; + if ((short_packet_size > 0) || (total_bytes == 0)) num_packets++; // Schedule packets to be sent within interrupt edpt_schedule_packets(rhport, epnum, dir, num_packets, total_bytes); @@ -775,24 +675,23 @@ bool dcd_edpt_xfer (uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t // bytes should be written and second to keep the return value free to give back a boolean // success message. If total_bytes is too big, the FIFO will copy only what is available // into the USB buffer! -bool dcd_edpt_xfer_fifo (uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16_t total_bytes) -{ +bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t* ff, uint16_t total_bytes) { // USB buffers always work in bytes so to avoid unnecessary divisions we demand item_size = 1 TU_ASSERT(ff->item_size == 1); uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); - xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, dir); - xfer->buffer = NULL; - xfer->ff = ff; - xfer->total_len = total_bytes; + xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, dir); + xfer->buffer = NULL; + xfer->ff = ff; + xfer->total_len = total_bytes; uint16_t num_packets = (total_bytes / xfer->max_size); uint16_t const short_packet_size = total_bytes % xfer->max_size; // Zero-size packet is special case. - if ( short_packet_size > 0 || (total_bytes == 0) ) num_packets++; + if (short_packet_size > 0 || (total_bytes == 0)) num_packets++; // Schedule packets to be sent within interrupt edpt_schedule_packets(rhport, epnum, dir, num_packets, total_bytes); @@ -800,62 +699,52 @@ bool dcd_edpt_xfer_fifo (uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16 return true; } -static void dcd_edpt_disable (uint8_t rhport, uint8_t ep_addr, bool stall) -{ +static void dcd_edpt_disable(uint8_t rhport, uint8_t ep_addr, bool stall) { (void) rhport; - dwc2_regs_t *dwc2 = DWC2_REG(rhport); + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); - if ( dir == TUSB_DIR_IN ) - { + if (dir == TUSB_DIR_IN) { dwc2_epin_t* epin = dwc2->epin; // Only disable currently enabled non-control endpoint - if ( (epnum == 0) || !(epin[epnum].diepctl & DIEPCTL_EPENA) ) - { + if ((epnum == 0) || !(epin[epnum].diepctl & DIEPCTL_EPENA)) { epin[epnum].diepctl |= DIEPCTL_SNAK | (stall ? DIEPCTL_STALL : 0); - } - else - { + } else { // Stop transmitting packets and NAK IN xfers. epin[epnum].diepctl |= DIEPCTL_SNAK; - while ( (epin[epnum].diepint & DIEPINT_INEPNE) == 0 ) {} + while ((epin[epnum].diepint & DIEPINT_INEPNE) == 0) {} // Disable the endpoint. epin[epnum].diepctl |= DIEPCTL_EPDIS | (stall ? DIEPCTL_STALL : 0); - while ( (epin[epnum].diepint & DIEPINT_EPDISD_Msk) == 0 ) {} + while ((epin[epnum].diepint & DIEPINT_EPDISD_Msk) == 0) {} epin[epnum].diepint = DIEPINT_EPDISD; } // Flush the FIFO, and wait until we have confirmed it cleared. dwc2->grstctl = ((epnum << GRSTCTL_TXFNUM_Pos) | GRSTCTL_TXFFLSH); - while ( (dwc2->grstctl & GRSTCTL_TXFFLSH_Msk) != 0 ) {} - } - else - { + while ((dwc2->grstctl & GRSTCTL_TXFFLSH_Msk) != 0) {} + } else { dwc2_epout_t* epout = dwc2->epout; // Only disable currently enabled non-control endpoint - if ( (epnum == 0) || !(epout[epnum].doepctl & DOEPCTL_EPENA) ) - { + if ((epnum == 0) || !(epout[epnum].doepctl & DOEPCTL_EPENA)) { epout[epnum].doepctl |= stall ? DOEPCTL_STALL : 0; - } - else - { + } else { // Asserting GONAK is required to STALL an OUT endpoint. // Simpler to use polling here, we don't use the "B"OUTNAKEFF interrupt // anyway, and it can't be cleared by user code. If this while loop never // finishes, we have bigger problems than just the stack. dwc2->dctl |= DCTL_SGONAK; - while ( (dwc2->gintsts & GINTSTS_BOUTNAKEFF_Msk) == 0 ) {} + while ((dwc2->gintsts & GINTSTS_BOUTNAKEFF_Msk) == 0) {} // Ditto here- disable the endpoint. epout[epnum].doepctl |= DOEPCTL_EPDIS | (stall ? DOEPCTL_STALL : 0); - while ( (epout[epnum].doepint & DOEPINT_EPDISD_Msk) == 0 ) {} + while ((epout[epnum].doepint & DOEPINT_EPDISD_Msk) == 0) {} epout[epnum].doepint = DOEPINT_EPDISD; @@ -868,55 +757,46 @@ static void dcd_edpt_disable (uint8_t rhport, uint8_t ep_addr, bool stall) /** * Close an endpoint. */ -void dcd_edpt_close (uint8_t rhport, uint8_t ep_addr) -{ - dwc2_regs_t * dwc2 = DWC2_REG(rhport); +void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); dcd_edpt_disable(rhport, ep_addr, false); // Update max_size xfer_status[epnum][dir].max_size = 0; // max_size = 0 marks a disabled EP - required for changing FIFO allocation - if (dir == TUSB_DIR_IN) - { + if (dir == TUSB_DIR_IN) { uint16_t const fifo_size = (dwc2->dieptxf[epnum - 1] & DIEPTXF_INEPTXFD_Msk) >> DIEPTXF_INEPTXFD_Pos; uint16_t const fifo_start = (dwc2->dieptxf[epnum - 1] & DIEPTXF_INEPTXSA_Msk) >> DIEPTXF_INEPTXSA_Pos; // For now only the last opened endpoint can be closed without fuss. - TU_ASSERT(fifo_start == _dwc2_controller[rhport].ep_fifo_size/4 - _allocated_fifo_words_tx,); + TU_ASSERT(fifo_start == _dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx,); _allocated_fifo_words_tx -= fifo_size; - } - else - { + } else { _out_ep_closed = true; // Set flag such that RX FIFO gets reduced in size once RX FIFO is empty } } -void dcd_edpt_stall (uint8_t rhport, uint8_t ep_addr) -{ +void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { dcd_edpt_disable(rhport, ep_addr, true); } -void dcd_edpt_clear_stall (uint8_t rhport, uint8_t ep_addr) -{ +void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { (void) rhport; - dwc2_regs_t * dwc2 = DWC2_REG(rhport); + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); // Clear stall and reset data toggle - if ( dir == TUSB_DIR_IN ) - { + if (dir == TUSB_DIR_IN) { dwc2->epin[epnum].diepctl &= ~DIEPCTL_STALL; dwc2->epin[epnum].diepctl |= DIEPCTL_SD0PID_SEVNFRM; - } - else - { + } else { dwc2->epout[epnum].doepctl &= ~DOEPCTL_STALL; dwc2->epout[epnum].doepctl |= DOEPCTL_SD0PID_SEVNFRM; } @@ -925,70 +805,63 @@ void dcd_edpt_clear_stall (uint8_t rhport, uint8_t ep_addr) /*------------------------------------------------------------------*/ // Read a single data packet from receive FIFO -static void read_fifo_packet(uint8_t rhport, uint8_t * dst, uint16_t len) -{ +static void read_fifo_packet(uint8_t rhport, uint8_t* dst, uint16_t len) { (void) rhport; - dwc2_regs_t * dwc2 = DWC2_REG(rhport); - volatile const uint32_t * rx_fifo = dwc2->fifo[0]; + dwc2_regs_t* dwc2 = DWC2_REG(rhport); + volatile const uint32_t* rx_fifo = dwc2->fifo[0]; // Reading full available 32 bit words from fifo uint16_t full_words = len >> 2; - while(full_words--) - { + while (full_words--) { tu_unaligned_write32(dst, *rx_fifo); dst += 4; } // Read the remaining 1-3 bytes from fifo uint8_t const bytes_rem = len & 0x03; - if ( bytes_rem != 0 ) - { + if (bytes_rem != 0) { uint32_t const tmp = *rx_fifo; dst[0] = tu_u32_byte0(tmp); - if ( bytes_rem > 1 ) dst[1] = tu_u32_byte1(tmp); - if ( bytes_rem > 2 ) dst[2] = tu_u32_byte2(tmp); + if (bytes_rem > 1) dst[1] = tu_u32_byte1(tmp); + if (bytes_rem > 2) dst[2] = tu_u32_byte2(tmp); } } // Write a single data packet to EPIN FIFO -static void write_fifo_packet(uint8_t rhport, uint8_t fifo_num, uint8_t const * src, uint16_t len) -{ +static void write_fifo_packet(uint8_t rhport, uint8_t fifo_num, uint8_t const* src, uint16_t len) { (void) rhport; - dwc2_regs_t * dwc2 = DWC2_REG(rhport); - volatile uint32_t * tx_fifo = dwc2->fifo[fifo_num]; + dwc2_regs_t* dwc2 = DWC2_REG(rhport); + volatile uint32_t* tx_fifo = dwc2->fifo[fifo_num]; // Pushing full available 32 bit words to fifo uint16_t full_words = len >> 2; - while(full_words--) - { + while (full_words--) { *tx_fifo = tu_unaligned_read32(src); src += 4; } // Write the remaining 1-3 bytes into fifo uint8_t const bytes_rem = len & 0x03; - if ( bytes_rem ) - { + if (bytes_rem) { uint32_t tmp_word = src[0]; - if ( bytes_rem > 1 ) tmp_word |= (src[1] << 8); - if ( bytes_rem > 2 ) tmp_word |= (src[2] << 16); + if (bytes_rem > 1) tmp_word |= (src[1] << 8); + if (bytes_rem > 2) tmp_word |= (src[2] << 16); *tx_fifo = tmp_word; } } -static void handle_rxflvl_irq(uint8_t rhport) -{ - dwc2_regs_t * dwc2 = DWC2_REG(rhport); - volatile uint32_t const * rx_fifo = dwc2->fifo[0]; +static void handle_rxflvl_irq(uint8_t rhport) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); + volatile uint32_t const* rx_fifo = dwc2->fifo[0]; // Pop control word off FIFO uint32_t const ctl_word = dwc2->grxstsp; - uint8_t const pktsts = (ctl_word & GRXSTSP_PKTSTS_Msk ) >> GRXSTSP_PKTSTS_Pos; - uint8_t const epnum = (ctl_word & GRXSTSP_EPNUM_Msk ) >> GRXSTSP_EPNUM_Pos; - uint16_t const bcnt = (ctl_word & GRXSTSP_BCNT_Msk ) >> GRXSTSP_BCNT_Pos; + uint8_t const pktsts = (ctl_word & GRXSTSP_PKTSTS_Msk) >> GRXSTSP_PKTSTS_Pos; + uint8_t const epnum = (ctl_word & GRXSTSP_EPNUM_Msk) >> GRXSTSP_EPNUM_Pos; + uint16_t const bcnt = (ctl_word & GRXSTSP_BCNT_Msk) >> GRXSTSP_BCNT_Pos; dwc2_epout_t* epout = &dwc2->epout[epnum]; @@ -1003,10 +876,10 @@ static void handle_rxflvl_irq(uint8_t rhport) // TU_LOG(DWC2_DEBUG, " daint = %08lX, doepint = %04X\r\n", (unsigned long) dwc2->daint, (unsigned int) epout->doepint); //#endif - switch ( pktsts ) - { + switch (pktsts) { // Global OUT NAK: do nothing - case GRXSTS_PKTSTS_GLOBALOUTNAK: break; + case GRXSTS_PKTSTS_GLOBALOUTNAK: + break; case GRXSTS_PKTSTS_SETUPRX: // Setup packet received @@ -1015,26 +888,22 @@ static void handle_rxflvl_irq(uint8_t rhport) // only the last one is valid. _setup_packet[0] = (*rx_fifo); _setup_packet[1] = (*rx_fifo); - break; + break; case GRXSTS_PKTSTS_SETUPDONE: // Setup packet done (Interrupt) epout->doeptsiz |= (3 << DOEPTSIZ_STUPCNT_Pos); - break; + break; - case GRXSTS_PKTSTS_OUTRX: - { + case GRXSTS_PKTSTS_OUTRX: { // Out packet received - xfer_ctl_t *xfer = XFER_CTL_BASE(epnum, TUSB_DIR_OUT); + xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, TUSB_DIR_OUT); // Read packet off RxFIFO - if ( xfer->ff ) - { + if (xfer->ff) { // Ring buffer tu_fifo_write_n_const_addr_full_words(xfer->ff, (const void*) (uintptr_t) rx_fifo, bcnt); - } - else - { + } else { // Linear buffer read_fifo_packet(rhport, xfer->buffer, bcnt); @@ -1043,73 +912,64 @@ static void handle_rxflvl_irq(uint8_t rhport) } // Truncate transfer length in case of short packet - if ( bcnt < xfer->max_size ) - { + if (bcnt < xfer->max_size) { xfer->total_len -= (epout->doeptsiz & DOEPTSIZ_XFRSIZ_Msk) >> DOEPTSIZ_XFRSIZ_Pos; - if ( epnum == 0 ) - { + if (epnum == 0) { xfer->total_len -= ep0_pending[TUSB_DIR_OUT]; ep0_pending[TUSB_DIR_OUT] = 0; } } } - break; + break; - // Out packet done (Interrupt) + // Out packet done (Interrupt) case GRXSTS_PKTSTS_OUTDONE: - // Occurred on STM32L47 with dwc2 version 3.10a but not found on other version like 2.80a or 3.30a - // May (or not) be 3.10a specific feature/bug or depending on MCU configuration - // XFRC complete is additionally generated when - // - setup packet is received - // - complete the data stage of control write is complete - if ((epnum == 0) && (bcnt == 0) && (dwc2->gsnpsid >= DWC2_CORE_REV_3_00a)) - { - uint32_t doepint = epout->doepint; - - if (doepint & (DOEPINT_STPKTRX | DOEPINT_OTEPSPR)) - { - // skip this "no-data" transfer complete event - // Note: STPKTRX will be clear later by setup received handler - uint32_t clear_flags = DOEPINT_XFRC; - - if (doepint & DOEPINT_OTEPSPR) clear_flags |= DOEPINT_OTEPSPR; - - epout->doepint = clear_flags; - - // TU_LOG(DWC2_DEBUG, " FIX extra transfer complete on setup/data compete\r\n"); - } + // Occurred on STM32L47 with dwc2 version 3.10a but not found on other version like 2.80a or 3.30a + // May (or not) be 3.10a specific feature/bug or depending on MCU configuration + // XFRC complete is additionally generated when + // - setup packet is received + // - complete the data stage of control write is complete + if ((epnum == 0) && (bcnt == 0) && (dwc2->gsnpsid >= DWC2_CORE_REV_3_00a)) { + uint32_t doepint = epout->doepint; + + if (doepint & (DOEPINT_STPKTRX | DOEPINT_OTEPSPR)) { + // skip this "no-data" transfer complete event + // Note: STPKTRX will be clear later by setup received handler + uint32_t clear_flags = DOEPINT_XFRC; + + if (doepint & DOEPINT_OTEPSPR) clear_flags |= DOEPINT_OTEPSPR; + + epout->doepint = clear_flags; + + // TU_LOG(DWC2_DEBUG, " FIX extra transfer complete on setup/data compete\r\n"); } - break; + } + break; default: // Invalid TU_BREAKPOINT(); - break; + break; } } -static void handle_epout_irq (uint8_t rhport) -{ - dwc2_regs_t * dwc2 = DWC2_REG(rhport); +static void handle_epout_irq(uint8_t rhport) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const ep_count = _dwc2_controller[rhport].ep_count; // DAINT for a given EP clears when DOEPINTx is cleared. // OEPINT will be cleared when DAINT's out bits are cleared. - for ( uint8_t n = 0; n < ep_count; n++ ) - { - if ( dwc2->daint & TU_BIT(DAINT_OEPINT_Pos + n) ) - { + for (uint8_t n = 0; n < ep_count; n++) { + if (dwc2->daint & TU_BIT(DAINT_OEPINT_Pos + n)) { dwc2_epout_t* epout = &dwc2->epout[n]; uint32_t const doepint = epout->doepint; // SETUP packet Setup Phase done. - if ( doepint & DOEPINT_STUP ) - { + if (doepint & DOEPINT_STUP) { uint32_t clear_flag = DOEPINT_STUP; // STPKTRX is only available for version from 3_00a - if ((doepint & DOEPINT_STPKTRX) && (dwc2->gsnpsid >= DWC2_CORE_REV_3_00a)) - { + if ((doepint & DOEPINT_STPKTRX) && (dwc2->gsnpsid >= DWC2_CORE_REV_3_00a)) { clear_flag |= DOEPINT_STPKTRX; } @@ -1118,20 +978,16 @@ static void handle_epout_irq (uint8_t rhport) } // OUT XFER complete - if ( epout->doepint & DOEPINT_XFRC ) - { + if (epout->doepint & DOEPINT_XFRC) { epout->doepint = DOEPINT_XFRC; - xfer_ctl_t *xfer = XFER_CTL_BASE(n, TUSB_DIR_OUT); + xfer_ctl_t* xfer = XFER_CTL_BASE(n, TUSB_DIR_OUT); // EP0 can only handle one packet - if ( (n == 0) && ep0_pending[TUSB_DIR_OUT] ) - { + if ((n == 0) && ep0_pending[TUSB_DIR_OUT]) { // Schedule another packet to be received. edpt_schedule_packets(rhport, n, TUSB_DIR_OUT, 1, ep0_pending[TUSB_DIR_OUT]); - } - else - { + } else { dcd_event_xfer_complete(rhport, n, xfer->total_len, XFER_RESULT_SUCCESS, true); } } @@ -1139,40 +995,32 @@ static void handle_epout_irq (uint8_t rhport) } } -static void handle_epin_irq (uint8_t rhport) -{ - dwc2_regs_t * dwc2 = DWC2_REG(rhport); +static void handle_epin_irq(uint8_t rhport) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const ep_count = _dwc2_controller[rhport].ep_count; - dwc2_epin_t* epin = dwc2->epin; + dwc2_epin_t* epin = dwc2->epin; // DAINT for a given EP clears when DIEPINTx is cleared. // IEPINT will be cleared when DAINT's out bits are cleared. - for ( uint8_t n = 0; n < ep_count; n++ ) - { - if ( dwc2->daint & TU_BIT(DAINT_IEPINT_Pos + n) ) - { + for (uint8_t n = 0; n < ep_count; n++) { + if (dwc2->daint & TU_BIT(DAINT_IEPINT_Pos + n)) { // IN XFER complete (entire xfer). - xfer_ctl_t *xfer = XFER_CTL_BASE(n, TUSB_DIR_IN); + xfer_ctl_t* xfer = XFER_CTL_BASE(n, TUSB_DIR_IN); - if ( epin[n].diepint & DIEPINT_XFRC ) - { + if (epin[n].diepint & DIEPINT_XFRC) { epin[n].diepint = DIEPINT_XFRC; // EP0 can only handle one packet - if ( (n == 0) && ep0_pending[TUSB_DIR_IN] ) - { + if ((n == 0) && ep0_pending[TUSB_DIR_IN]) { // Schedule another packet to be transmitted. edpt_schedule_packets(rhport, n, TUSB_DIR_IN, 1, ep0_pending[TUSB_DIR_IN]); - } - else - { + } else { dcd_event_xfer_complete(rhport, n | TUSB_DIR_IN_MASK, xfer->total_len, XFER_RESULT_SUCCESS, true); } } // XFER FIFO empty - if ( (epin[n].diepint & DIEPINT_TXFE) && (dwc2->diepempmsk & (1 << n)) ) - { + if ((epin[n].diepint & DIEPINT_TXFE) && (dwc2->diepempmsk & (1 << n))) { // diepint's TXFE bit is read-only, software cannot clear it. // It will only be cleared by hardware when written bytes is more than // - 64 bytes or @@ -1181,8 +1029,7 @@ static void handle_epin_irq (uint8_t rhport) uint16_t remaining_packets = (epin[n].dieptsiz & DIEPTSIZ_PKTCNT_Msk) >> DIEPTSIZ_PKTCNT_Pos; // Process every single packet (only whole packets can be written to fifo) - for ( uint16_t i = 0; i < remaining_packets; i++ ) - { + for (uint16_t i = 0; i < remaining_packets; i++) { uint16_t const remaining_bytes = (epin[n].dieptsiz & DIEPTSIZ_XFRSIZ_Msk) >> DIEPTSIZ_XFRSIZ_Pos; // Packet can not be larger than ep max size @@ -1190,16 +1037,13 @@ static void handle_epin_irq (uint8_t rhport) // It's only possible to write full packets into FIFO. Therefore DTXFSTS register of current // EP has to be checked if the buffer can take another WHOLE packet - if ( packet_size > ((epin[n].dtxfsts & DTXFSTS_INEPTFSAV_Msk) << 2) ) break; + if (packet_size > ((epin[n].dtxfsts & DTXFSTS_INEPTFSAV_Msk) << 2)) break; // Push packet to Tx-FIFO - if ( xfer->ff ) - { - volatile uint32_t *tx_fifo = dwc2->fifo[n]; + if (xfer->ff) { + volatile uint32_t* tx_fifo = dwc2->fifo[n]; tu_fifo_read_n_const_addr_full_words(xfer->ff, (void*) (uintptr_t) tx_fifo, packet_size); - } - else - { + } else { write_fifo_packet(rhport, n, xfer->buffer, packet_size); // Increment pointer to xfer data @@ -1208,8 +1052,7 @@ static void handle_epin_irq (uint8_t rhport) } // Turn off TXFE if all bytes are written. - if ( ((epin[n].dieptsiz & DIEPTSIZ_XFRSIZ_Msk) >> DIEPTSIZ_XFRSIZ_Pos) == 0 ) - { + if (((epin[n].dieptsiz & DIEPTSIZ_XFRSIZ_Msk) >> DIEPTSIZ_XFRSIZ_Pos) == 0) { dwc2->diepempmsk &= ~(1 << n); } } @@ -1217,55 +1060,49 @@ static void handle_epin_irq (uint8_t rhport) } } -void dcd_int_handler(uint8_t rhport) -{ - dwc2_regs_t *dwc2 = DWC2_REG(rhport); +void dcd_int_handler(uint8_t rhport) { + dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint32_t const int_mask = dwc2->gintmsk; uint32_t const int_status = dwc2->gintsts & int_mask; - if(int_status & GINTSTS_USBRST) - { + if (int_status & GINTSTS_USBRST) { // USBRST is start of reset. dwc2->gintsts = GINTSTS_USBRST; bus_reset(rhport); } - if(int_status & GINTSTS_ENUMDNE) - { + if (int_status & GINTSTS_ENUMDNE) { // ENUMDNE is the end of reset where speed of the link is detected dwc2->gintsts = GINTSTS_ENUMDNE; tusb_speed_t speed; - switch ((dwc2->dsts & DSTS_ENUMSPD_Msk) >> DSTS_ENUMSPD_Pos) - { + switch ((dwc2->dsts & DSTS_ENUMSPD_Msk) >> DSTS_ENUMSPD_Pos) { case DSTS_ENUMSPD_HS: speed = TUSB_SPEED_HIGH; - break; + break; case DSTS_ENUMSPD_LS: speed = TUSB_SPEED_LOW; - break; + break; case DSTS_ENUMSPD_FS_HSPHY: case DSTS_ENUMSPD_FS: default: speed = TUSB_SPEED_FULL; - break; + break; } dcd_event_bus_reset(rhport, speed, true); } - if(int_status & GINTSTS_USBSUSP) - { + if (int_status & GINTSTS_USBSUSP) { dwc2->gintsts = GINTSTS_USBSUSP; dcd_event_bus_signal(rhport, DCD_EVENT_SUSPEND, true); } - if(int_status & GINTSTS_WKUINT) - { + if (int_status & GINTSTS_WKUINT) { dwc2->gintsts = GINTSTS_WKUINT; dcd_event_bus_signal(rhport, DCD_EVENT_RESUME, true); } @@ -1273,30 +1110,24 @@ void dcd_int_handler(uint8_t rhport) // TODO check GINTSTS_DISCINT for disconnect detection // if(int_status & GINTSTS_DISCINT) - if(int_status & GINTSTS_OTGINT) - { + if (int_status & GINTSTS_OTGINT) { // OTG INT bit is read-only uint32_t const otg_int = dwc2->gotgint; - if (otg_int & GOTGINT_SEDET) - { + if (otg_int & GOTGINT_SEDET) { dcd_event_bus_signal(rhport, DCD_EVENT_UNPLUGGED, true); } dwc2->gotgint = otg_int; } - if(int_status & GINTSTS_SOF) - { + if (int_status & GINTSTS_SOF) { dwc2->gotgint = GINTSTS_SOF; - if (_sof_en) - { + if (_sof_en) { uint32_t frame = (dwc2->dsts & (DSTS_FNSOF)) >> 8; dcd_event_sof(rhport, frame, true); - } - else - { + } else { // Disable SOF interrupt if SOF was not explicitly enabled. SOF was used for remote wakeup detection dwc2->gintmsk &= ~GINTMSK_SOFM; } @@ -1305,22 +1136,19 @@ void dcd_int_handler(uint8_t rhport) } // RxFIFO non-empty interrupt handling. - if(int_status & GINTSTS_RXFLVL) - { + if (int_status & GINTSTS_RXFLVL) { // RXFLVL bit is read-only // Mask out RXFLVL while reading data from FIFO dwc2->gintmsk &= ~GINTMSK_RXFLVLM; // Loop until all available packets were handled - do - { + do { handle_rxflvl_irq(rhport); - } while(dwc2->gotgint & GINTSTS_RXFLVL); + } while (dwc2->gotgint & GINTSTS_RXFLVL); // Manage RX FIFO size - if (_out_ep_closed) - { + if (_out_ep_closed) { update_grxfsiz(rhport); // Disable flag @@ -1331,15 +1159,13 @@ void dcd_int_handler(uint8_t rhport) } // OUT endpoint interrupt handling. - if(int_status & GINTSTS_OEPINT) - { + if (int_status & GINTSTS_OEPINT) { // OEPINT is read-only, clear using DOEPINTn handle_epout_irq(rhport); } // IN endpoint interrupt handling. - if(int_status & GINTSTS_IEPINT) - { + if (int_status & GINTSTS_IEPINT) { // IEPINT bit read-only, clear using DIEPINTn handle_epin_irq(rhport); } -- cgit v1.3.1 From 9f0223dccd9992f936054bae3c6256280af7f26a Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 31 Oct 2023 10:58:15 +0700 Subject: minor clean up --- hw/bsp/stm32f7/family.c | 2 +- src/portable/synopsys/dwc2/dwc2_type.h | 1790 ++++++++++++++++---------------- 2 files changed, 911 insertions(+), 881 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/stm32f7/family.c b/hw/bsp/stm32f7/family.c index b504c435a..18cee073d 100644 --- a/hw/bsp/stm32f7/family.c +++ b/hw/bsp/stm32f7/family.c @@ -199,7 +199,7 @@ void board_init(void) { __HAL_RCC_OTGPHYC_CLK_ENABLE(); #else - // MUC with external ULPI PHY + // MCU with external ULPI PHY /* ULPI CLK */ GPIO_InitStruct.Pin = GPIO_PIN_5; diff --git a/src/portable/synopsys/dwc2/dwc2_type.h b/src/portable/synopsys/dwc2/dwc2_type.h index 6516882da..c15771237 100644 --- a/src/portable/synopsys/dwc2/dwc2_type.h +++ b/src/portable/synopsys/dwc2/dwc2_type.h @@ -32,7 +32,7 @@ typedef struct uint32_t ep_fifo_size; }dwc2_controller_t; -/* DWC OTG HW Release versions */ +// DWC OTG HW Release versions #define DWC2_CORE_REV_2_71a 0x4f54271a #define DWC2_CORE_REV_2_72a 0x4f54272a #define DWC2_CORE_REV_2_80a 0x4f54280a @@ -49,7 +49,7 @@ typedef struct #define DWC2_HS_IOT_REV_1_00a 0x5532100a #define DWC2_CORE_REV_MASK 0x0000ffff -/* DWC OTG HW Core ID */ +// DWC OTG HW Core ID #define DWC2_OTG_ID 0x4f540000 #define DWC2_FS_IOT_ID 0x55310000 #define DWC2_HS_IOT_ID 0x55320000 @@ -58,13 +58,13 @@ typedef struct // HS PHY typedef struct { - volatile uint32_t HS_PHYC_PLL; // This register is used to control the PLL of the HS PHY. 000h */ - volatile uint32_t Reserved04; // Reserved 004h */ - volatile uint32_t Reserved08; // Reserved 008h */ - volatile uint32_t HS_PHYC_TUNE; // This register is used to control the tuning interface of the High Speed PHY. 00Ch */ - volatile uint32_t Reserved10; // Reserved 010h */ - volatile uint32_t Reserved14; // Reserved 014h */ - volatile uint32_t HS_PHYC_LDO; // This register is used to control the regulator (LDO). 018h */ + volatile uint32_t HS_PHYC_PLL; // 000h This register is used to control the PLL of the HS PHY. + volatile uint32_t Reserved04; // 004h Reserved + volatile uint32_t Reserved08; // 008h Reserved + volatile uint32_t HS_PHYC_TUNE; // 00Ch This register is used to control the tuning interface of the High Speed PHY. + volatile uint32_t Reserved10; // 010h Reserved + volatile uint32_t Reserved14; // 014h Reserved + volatile uint32_t HS_PHYC_LDO; // 018h This register is used to control the regulator (LDO). } HS_PHYC_GlobalTypeDef; #endif @@ -299,103 +299,103 @@ TU_VERIFY_STATIC(offsetof(dwc2_regs_t, fifo ) == 0x1000, "incorrect size"); /******************** Bit definition for GOTGCTL register ********************/ #define GOTGCTL_SRQSCS_Pos (0U) -#define GOTGCTL_SRQSCS_Msk (0x1UL << GOTGCTL_SRQSCS_Pos) // 0x00000001 */ -#define GOTGCTL_SRQSCS GOTGCTL_SRQSCS_Msk // Session request success */ +#define GOTGCTL_SRQSCS_Msk (0x1UL << GOTGCTL_SRQSCS_Pos) // 0x00000001 +#define GOTGCTL_SRQSCS GOTGCTL_SRQSCS_Msk // Session request success #define GOTGCTL_SRQ_Pos (1U) -#define GOTGCTL_SRQ_Msk (0x1UL << GOTGCTL_SRQ_Pos) // 0x00000002 */ -#define GOTGCTL_SRQ GOTGCTL_SRQ_Msk // Session request */ +#define GOTGCTL_SRQ_Msk (0x1UL << GOTGCTL_SRQ_Pos) // 0x00000002 +#define GOTGCTL_SRQ GOTGCTL_SRQ_Msk // Session request #define GOTGCTL_VBVALOEN_Pos (2U) -#define GOTGCTL_VBVALOEN_Msk (0x1UL << GOTGCTL_VBVALOEN_Pos) // 0x00000004 */ -#define GOTGCTL_VBVALOEN GOTGCTL_VBVALOEN_Msk // VBUS valid override enable */ +#define GOTGCTL_VBVALOEN_Msk (0x1UL << GOTGCTL_VBVALOEN_Pos) // 0x00000004 +#define GOTGCTL_VBVALOEN GOTGCTL_VBVALOEN_Msk // VBUS valid override enable #define GOTGCTL_VBVALOVAL_Pos (3U) -#define GOTGCTL_VBVALOVAL_Msk (0x1UL << GOTGCTL_VBVALOVAL_Pos) // 0x00000008 */ -#define GOTGCTL_VBVALOVAL GOTGCTL_VBVALOVAL_Msk // VBUS valid override value */ +#define GOTGCTL_VBVALOVAL_Msk (0x1UL << GOTGCTL_VBVALOVAL_Pos) // 0x00000008 +#define GOTGCTL_VBVALOVAL GOTGCTL_VBVALOVAL_Msk // VBUS valid override value #define GOTGCTL_AVALOEN_Pos (4U) -#define GOTGCTL_AVALOEN_Msk (0x1UL << GOTGCTL_AVALOEN_Pos) // 0x00000010 */ -#define GOTGCTL_AVALOEN GOTGCTL_AVALOEN_Msk // A-peripheral session valid override enable */ +#define GOTGCTL_AVALOEN_Msk (0x1UL << GOTGCTL_AVALOEN_Pos) // 0x00000010 +#define GOTGCTL_AVALOEN GOTGCTL_AVALOEN_Msk // A-peripheral session valid override enable #define GOTGCTL_AVALOVAL_Pos (5U) -#define GOTGCTL_AVALOVAL_Msk (0x1UL << GOTGCTL_AVALOVAL_Pos) // 0x00000020 */ -#define GOTGCTL_AVALOVAL GOTGCTL_AVALOVAL_Msk // A-peripheral session valid override value */ +#define GOTGCTL_AVALOVAL_Msk (0x1UL << GOTGCTL_AVALOVAL_Pos) // 0x00000020 +#define GOTGCTL_AVALOVAL GOTGCTL_AVALOVAL_Msk // A-peripheral session valid override value #define GOTGCTL_BVALOEN_Pos (6U) -#define GOTGCTL_BVALOEN_Msk (0x1UL << GOTGCTL_BVALOEN_Pos) // 0x00000040 */ -#define GOTGCTL_BVALOEN GOTGCTL_BVALOEN_Msk // B-peripheral session valid override enable */ +#define GOTGCTL_BVALOEN_Msk (0x1UL << GOTGCTL_BVALOEN_Pos) // 0x00000040 +#define GOTGCTL_BVALOEN GOTGCTL_BVALOEN_Msk // B-peripheral session valid override enable #define GOTGCTL_BVALOVAL_Pos (7U) -#define GOTGCTL_BVALOVAL_Msk (0x1UL << GOTGCTL_BVALOVAL_Pos) // 0x00000080 */ -#define GOTGCTL_BVALOVAL GOTGCTL_BVALOVAL_Msk // B-peripheral session valid override value */ +#define GOTGCTL_BVALOVAL_Msk (0x1UL << GOTGCTL_BVALOVAL_Pos) // 0x00000080 +#define GOTGCTL_BVALOVAL GOTGCTL_BVALOVAL_Msk // B-peripheral session valid override value #define GOTGCTL_HNGSCS_Pos (8U) -#define GOTGCTL_HNGSCS_Msk (0x1UL << GOTGCTL_HNGSCS_Pos) // 0x00000100 */ -#define GOTGCTL_HNGSCS GOTGCTL_HNGSCS_Msk // Host set HNP enable */ +#define GOTGCTL_HNGSCS_Msk (0x1UL << GOTGCTL_HNGSCS_Pos) // 0x00000100 +#define GOTGCTL_HNGSCS GOTGCTL_HNGSCS_Msk // Host set HNP enable #define GOTGCTL_HNPRQ_Pos (9U) -#define GOTGCTL_HNPRQ_Msk (0x1UL << GOTGCTL_HNPRQ_Pos) // 0x00000200 */ -#define GOTGCTL_HNPRQ GOTGCTL_HNPRQ_Msk // HNP request */ +#define GOTGCTL_HNPRQ_Msk (0x1UL << GOTGCTL_HNPRQ_Pos) // 0x00000200 +#define GOTGCTL_HNPRQ GOTGCTL_HNPRQ_Msk // HNP request #define GOTGCTL_HSHNPEN_Pos (10U) -#define GOTGCTL_HSHNPEN_Msk (0x1UL << GOTGCTL_HSHNPEN_Pos) // 0x00000400 */ -#define GOTGCTL_HSHNPEN GOTGCTL_HSHNPEN_Msk // Host set HNP enable */ +#define GOTGCTL_HSHNPEN_Msk (0x1UL << GOTGCTL_HSHNPEN_Pos) // 0x00000400 +#define GOTGCTL_HSHNPEN GOTGCTL_HSHNPEN_Msk // Host set HNP enable #define GOTGCTL_DHNPEN_Pos (11U) -#define GOTGCTL_DHNPEN_Msk (0x1UL << GOTGCTL_DHNPEN_Pos) // 0x00000800 */ -#define GOTGCTL_DHNPEN GOTGCTL_DHNPEN_Msk // Device HNP enabled */ +#define GOTGCTL_DHNPEN_Msk (0x1UL << GOTGCTL_DHNPEN_Pos) // 0x00000800 +#define GOTGCTL_DHNPEN GOTGCTL_DHNPEN_Msk // Device HNP enabled #define GOTGCTL_EHEN_Pos (12U) -#define GOTGCTL_EHEN_Msk (0x1UL << GOTGCTL_EHEN_Pos) // 0x00001000 */ -#define GOTGCTL_EHEN GOTGCTL_EHEN_Msk // Embedded host enable */ +#define GOTGCTL_EHEN_Msk (0x1UL << GOTGCTL_EHEN_Pos) // 0x00001000 +#define GOTGCTL_EHEN GOTGCTL_EHEN_Msk // Embedded host enable #define GOTGCTL_CIDSTS_Pos (16U) -#define GOTGCTL_CIDSTS_Msk (0x1UL << GOTGCTL_CIDSTS_Pos) // 0x00010000 */ -#define GOTGCTL_CIDSTS GOTGCTL_CIDSTS_Msk // Connector ID status */ +#define GOTGCTL_CIDSTS_Msk (0x1UL << GOTGCTL_CIDSTS_Pos) // 0x00010000 +#define GOTGCTL_CIDSTS GOTGCTL_CIDSTS_Msk // Connector ID status #define GOTGCTL_DBCT_Pos (17U) -#define GOTGCTL_DBCT_Msk (0x1UL << GOTGCTL_DBCT_Pos) // 0x00020000 */ -#define GOTGCTL_DBCT GOTGCTL_DBCT_Msk // Long/short debounce time */ +#define GOTGCTL_DBCT_Msk (0x1UL << GOTGCTL_DBCT_Pos) // 0x00020000 +#define GOTGCTL_DBCT GOTGCTL_DBCT_Msk // Long/short debounce time #define GOTGCTL_ASVLD_Pos (18U) -#define GOTGCTL_ASVLD_Msk (0x1UL << GOTGCTL_ASVLD_Pos) // 0x00040000 */ -#define GOTGCTL_ASVLD GOTGCTL_ASVLD_Msk // A-session valid */ +#define GOTGCTL_ASVLD_Msk (0x1UL << GOTGCTL_ASVLD_Pos) // 0x00040000 +#define GOTGCTL_ASVLD GOTGCTL_ASVLD_Msk // A-session valid #define GOTGCTL_BSESVLD_Pos (19U) -#define GOTGCTL_BSESVLD_Msk (0x1UL << GOTGCTL_BSESVLD_Pos) // 0x00080000 */ -#define GOTGCTL_BSESVLD GOTGCTL_BSESVLD_Msk // B-session valid */ +#define GOTGCTL_BSESVLD_Msk (0x1UL << GOTGCTL_BSESVLD_Pos) // 0x00080000 +#define GOTGCTL_BSESVLD GOTGCTL_BSESVLD_Msk // B-session valid #define GOTGCTL_OTGVER_Pos (20U) -#define GOTGCTL_OTGVER_Msk (0x1UL << GOTGCTL_OTGVER_Pos) // 0x00100000 */ -#define GOTGCTL_OTGVER GOTGCTL_OTGVER_Msk // OTG version */ +#define GOTGCTL_OTGVER_Msk (0x1UL << GOTGCTL_OTGVER_Pos) // 0x00100000 +#define GOTGCTL_OTGVER GOTGCTL_OTGVER_Msk // OTG version /******************** Bit definition for HCFG register ********************/ #define HCFG_FSLSPCS_Pos (0U) -#define HCFG_FSLSPCS_Msk (0x3UL << HCFG_FSLSPCS_Pos) // 0x00000003 */ -#define HCFG_FSLSPCS HCFG_FSLSPCS_Msk // FS/LS PHY clock select */ -#define HCFG_FSLSPCS_0 (0x1UL << HCFG_FSLSPCS_Pos) // 0x00000001 */ -#define HCFG_FSLSPCS_1 (0x2UL << HCFG_FSLSPCS_Pos) // 0x00000002 */ +#define HCFG_FSLSPCS_Msk (0x3UL << HCFG_FSLSPCS_Pos) // 0x00000003 +#define HCFG_FSLSPCS HCFG_FSLSPCS_Msk // FS/LS PHY clock select +#define HCFG_FSLSPCS_0 (0x1UL << HCFG_FSLSPCS_Pos) // 0x00000001 +#define HCFG_FSLSPCS_1 (0x2UL << HCFG_FSLSPCS_Pos) // 0x00000002 #define HCFG_FSLSS_Pos (2U) -#define HCFG_FSLSS_Msk (0x1UL << HCFG_FSLSS_Pos) // 0x00000004 */ -#define HCFG_FSLSS HCFG_FSLSS_Msk // FS- and LS-only support */ +#define HCFG_FSLSS_Msk (0x1UL << HCFG_FSLSS_Pos) // 0x00000004 +#define HCFG_FSLSS HCFG_FSLSS_Msk // FS- and LS-only support /******************** Bit definition for PCGCR register ********************/ #define PCGCR_STPPCLK_Pos (0U) -#define PCGCR_STPPCLK_Msk (0x1UL << PCGCR_STPPCLK_Pos) // 0x00000001 */ -#define PCGCR_STPPCLK PCGCR_STPPCLK_Msk // Stop PHY clock */ +#define PCGCR_STPPCLK_Msk (0x1UL << PCGCR_STPPCLK_Pos) // 0x00000001 +#define PCGCR_STPPCLK PCGCR_STPPCLK_Msk // Stop PHY clock #define PCGCR_GATEHCLK_Pos (1U) -#define PCGCR_GATEHCLK_Msk (0x1UL << PCGCR_GATEHCLK_Pos) // 0x00000002 */ -#define PCGCR_GATEHCLK PCGCR_GATEHCLK_Msk // Gate HCLK */ +#define PCGCR_GATEHCLK_Msk (0x1UL << PCGCR_GATEHCLK_Pos) // 0x00000002 +#define PCGCR_GATEHCLK PCGCR_GATEHCLK_Msk // Gate HCLK #define PCGCR_PHYSUSP_Pos (4U) -#define PCGCR_PHYSUSP_Msk (0x1UL << PCGCR_PHYSUSP_Pos) // 0x00000010 */ -#define PCGCR_PHYSUSP PCGCR_PHYSUSP_Msk // PHY suspended */ +#define PCGCR_PHYSUSP_Msk (0x1UL << PCGCR_PHYSUSP_Pos) // 0x00000010 +#define PCGCR_PHYSUSP PCGCR_PHYSUSP_Msk // PHY suspended /******************** Bit definition for GOTGINT register ********************/ #define GOTGINT_SEDET_Pos (2U) -#define GOTGINT_SEDET_Msk (0x1UL << GOTGINT_SEDET_Pos) // 0x00000004 */ -#define GOTGINT_SEDET GOTGINT_SEDET_Msk // Session end detected */ +#define GOTGINT_SEDET_Msk (0x1UL << GOTGINT_SEDET_Pos) // 0x00000004 +#define GOTGINT_SEDET GOTGINT_SEDET_Msk // Session end detected #define GOTGINT_SRSSCHG_Pos (8U) -#define GOTGINT_SRSSCHG_Msk (0x1UL << GOTGINT_SRSSCHG_Pos) // 0x00000100 */ -#define GOTGINT_SRSSCHG GOTGINT_SRSSCHG_Msk // Session request success status change */ +#define GOTGINT_SRSSCHG_Msk (0x1UL << GOTGINT_SRSSCHG_Pos) // 0x00000100 +#define GOTGINT_SRSSCHG GOTGINT_SRSSCHG_Msk // Session request success status change #define GOTGINT_HNSSCHG_Pos (9U) -#define GOTGINT_HNSSCHG_Msk (0x1UL << GOTGINT_HNSSCHG_Pos) // 0x00000200 */ -#define GOTGINT_HNSSCHG GOTGINT_HNSSCHG_Msk // Host negotiation success status change */ +#define GOTGINT_HNSSCHG_Msk (0x1UL << GOTGINT_HNSSCHG_Pos) // 0x00000200 +#define GOTGINT_HNSSCHG GOTGINT_HNSSCHG_Msk // Host negotiation success status change #define GOTGINT_HNGDET_Pos (17U) -#define GOTGINT_HNGDET_Msk (0x1UL << GOTGINT_HNGDET_Pos) // 0x00020000 */ -#define GOTGINT_HNGDET GOTGINT_HNGDET_Msk // Host negotiation detected */ +#define GOTGINT_HNGDET_Msk (0x1UL << GOTGINT_HNGDET_Pos) // 0x00020000 +#define GOTGINT_HNGDET GOTGINT_HNGDET_Msk // Host negotiation detected #define GOTGINT_ADTOCHG_Pos (18U) -#define GOTGINT_ADTOCHG_Msk (0x1UL << GOTGINT_ADTOCHG_Pos) // 0x00040000 */ -#define GOTGINT_ADTOCHG GOTGINT_ADTOCHG_Msk // A-device timeout change */ +#define GOTGINT_ADTOCHG_Msk (0x1UL << GOTGINT_ADTOCHG_Pos) // 0x00040000 +#define GOTGINT_ADTOCHG GOTGINT_ADTOCHG_Msk // A-device timeout change #define GOTGINT_DBCDNE_Pos (19U) -#define GOTGINT_DBCDNE_Msk (0x1UL << GOTGINT_DBCDNE_Pos) // 0x00080000 */ -#define GOTGINT_DBCDNE GOTGINT_DBCDNE_Msk // Debounce done */ +#define GOTGINT_DBCDNE_Msk (0x1UL << GOTGINT_DBCDNE_Pos) // 0x00080000 +#define GOTGINT_DBCDNE GOTGINT_DBCDNE_Msk // Debounce done #define GOTGINT_IDCHNG_Pos (20U) -#define GOTGINT_IDCHNG_Msk (0x1UL << GOTGINT_IDCHNG_Pos) // 0x00100000 */ -#define GOTGINT_IDCHNG GOTGINT_IDCHNG_Msk // Change in ID pin input value */ +#define GOTGINT_IDCHNG_Msk (0x1UL << GOTGINT_IDCHNG_Pos) // 0x00100000 +#define GOTGINT_IDCHNG GOTGINT_IDCHNG_Msk // Change in ID pin input value /******************** Bit definition for DCFG register ********************/ #define DCFG_DSPD_Pos (0U) @@ -406,92 +406,92 @@ TU_VERIFY_STATIC(offsetof(dwc2_regs_t, fifo ) == 0x1000, "incorrect size"); #define DCFG_DSPD_FS 3 // Fullspeed on FS PHY #define DCFG_NZLSOHSK_Pos (2U) -#define DCFG_NZLSOHSK_Msk (0x1UL << DCFG_NZLSOHSK_Pos) // 0x00000004 */ -#define DCFG_NZLSOHSK DCFG_NZLSOHSK_Msk // Nonzero-length status OUT handshake */ +#define DCFG_NZLSOHSK_Msk (0x1UL << DCFG_NZLSOHSK_Pos) // 0x00000004 +#define DCFG_NZLSOHSK DCFG_NZLSOHSK_Msk // Nonzero-length status OUT handshake #define DCFG_DAD_Pos (4U) -#define DCFG_DAD_Msk (0x7FUL << DCFG_DAD_Pos) // 0x000007F0 */ -#define DCFG_DAD DCFG_DAD_Msk // Device address */ -#define DCFG_DAD_0 (0x01UL << DCFG_DAD_Pos) // 0x00000010 */ -#define DCFG_DAD_1 (0x02UL << DCFG_DAD_Pos) // 0x00000020 */ -#define DCFG_DAD_2 (0x04UL << DCFG_DAD_Pos) // 0x00000040 */ -#define DCFG_DAD_3 (0x08UL << DCFG_DAD_Pos) // 0x00000080 */ -#define DCFG_DAD_4 (0x10UL << DCFG_DAD_Pos) // 0x00000100 */ -#define DCFG_DAD_5 (0x20UL << DCFG_DAD_Pos) // 0x00000200 */ -#define DCFG_DAD_6 (0x40UL << DCFG_DAD_Pos) // 0x00000400 */ +#define DCFG_DAD_Msk (0x7FUL << DCFG_DAD_Pos) // 0x000007F0 +#define DCFG_DAD DCFG_DAD_Msk // Device address +#define DCFG_DAD_0 (0x01UL << DCFG_DAD_Pos) // 0x00000010 +#define DCFG_DAD_1 (0x02UL << DCFG_DAD_Pos) // 0x00000020 +#define DCFG_DAD_2 (0x04UL << DCFG_DAD_Pos) // 0x00000040 +#define DCFG_DAD_3 (0x08UL << DCFG_DAD_Pos) // 0x00000080 +#define DCFG_DAD_4 (0x10UL << DCFG_DAD_Pos) // 0x00000100 +#define DCFG_DAD_5 (0x20UL << DCFG_DAD_Pos) // 0x00000200 +#define DCFG_DAD_6 (0x40UL << DCFG_DAD_Pos) // 0x00000400 #define DCFG_PFIVL_Pos (11U) -#define DCFG_PFIVL_Msk (0x3UL << DCFG_PFIVL_Pos) // 0x00001800 */ -#define DCFG_PFIVL DCFG_PFIVL_Msk // Periodic (micro)frame interval */ -#define DCFG_PFIVL_0 (0x1UL << DCFG_PFIVL_Pos) // 0x00000800 */ -#define DCFG_PFIVL_1 (0x2UL << DCFG_PFIVL_Pos) // 0x00001000 */ +#define DCFG_PFIVL_Msk (0x3UL << DCFG_PFIVL_Pos) // 0x00001800 +#define DCFG_PFIVL DCFG_PFIVL_Msk // Periodic (micro)frame interval +#define DCFG_PFIVL_0 (0x1UL << DCFG_PFIVL_Pos) // 0x00000800 +#define DCFG_PFIVL_1 (0x2UL << DCFG_PFIVL_Pos) // 0x00001000 #define DCFG_XCVRDLY_Pos (14U) -#define DCFG_XCVRDLY_Msk (0x1UL << DCFG_XCVRDLY_Pos) /*!< 0x00004000 */ +#define DCFG_XCVRDLY_Msk (0x1UL << DCFG_XCVRDLY_Pos) // 0x00004000 #define DCFG_XCVRDLY DCFG_XCVRDLY_Msk // Enables delay between xcvr_sel and txvalid during device chirp #define DCFG_PERSCHIVL_Pos (24U) -#define DCFG_PERSCHIVL_Msk (0x3UL << DCFG_PERSCHIVL_Pos) // 0x03000000 */ -#define DCFG_PERSCHIVL DCFG_PERSCHIVL_Msk // Periodic scheduling interval */ -#define DCFG_PERSCHIVL_0 (0x1UL << DCFG_PERSCHIVL_Pos) // 0x01000000 */ -#define DCFG_PERSCHIVL_1 (0x2UL << DCFG_PERSCHIVL_Pos) // 0x02000000 */ +#define DCFG_PERSCHIVL_Msk (0x3UL << DCFG_PERSCHIVL_Pos) // 0x03000000 +#define DCFG_PERSCHIVL DCFG_PERSCHIVL_Msk // Periodic scheduling interval +#define DCFG_PERSCHIVL_0 (0x1UL << DCFG_PERSCHIVL_Pos) // 0x01000000 +#define DCFG_PERSCHIVL_1 (0x2UL << DCFG_PERSCHIVL_Pos) // 0x02000000 /******************** Bit definition for DCTL register ********************/ #define DCTL_RWUSIG_Pos (0U) -#define DCTL_RWUSIG_Msk (0x1UL << DCTL_RWUSIG_Pos) // 0x00000001 */ -#define DCTL_RWUSIG DCTL_RWUSIG_Msk // Remote wakeup signaling */ +#define DCTL_RWUSIG_Msk (0x1UL << DCTL_RWUSIG_Pos) // 0x00000001 +#define DCTL_RWUSIG DCTL_RWUSIG_Msk // Remote wakeup signaling #define DCTL_SDIS_Pos (1U) -#define DCTL_SDIS_Msk (0x1UL << DCTL_SDIS_Pos) // 0x00000002 */ -#define DCTL_SDIS DCTL_SDIS_Msk // Soft disconnect */ +#define DCTL_SDIS_Msk (0x1UL << DCTL_SDIS_Pos) // 0x00000002 +#define DCTL_SDIS DCTL_SDIS_Msk // Soft disconnect #define DCTL_GINSTS_Pos (2U) -#define DCTL_GINSTS_Msk (0x1UL << DCTL_GINSTS_Pos) // 0x00000004 */ -#define DCTL_GINSTS DCTL_GINSTS_Msk // Global IN NAK status */ +#define DCTL_GINSTS_Msk (0x1UL << DCTL_GINSTS_Pos) // 0x00000004 +#define DCTL_GINSTS DCTL_GINSTS_Msk // Global IN NAK status #define DCTL_GONSTS_Pos (3U) -#define DCTL_GONSTS_Msk (0x1UL << DCTL_GONSTS_Pos) // 0x00000008 */ -#define DCTL_GONSTS DCTL_GONSTS_Msk // Global OUT NAK status */ +#define DCTL_GONSTS_Msk (0x1UL << DCTL_GONSTS_Pos) // 0x00000008 +#define DCTL_GONSTS DCTL_GONSTS_Msk // Global OUT NAK status #define DCTL_TCTL_Pos (4U) -#define DCTL_TCTL_Msk (0x7UL << DCTL_TCTL_Pos) // 0x00000070 */ -#define DCTL_TCTL DCTL_TCTL_Msk // Test control */ -#define DCTL_TCTL_0 (0x1UL << DCTL_TCTL_Pos) // 0x00000010 */ -#define DCTL_TCTL_1 (0x2UL << DCTL_TCTL_Pos) // 0x00000020 */ -#define DCTL_TCTL_2 (0x4UL << DCTL_TCTL_Pos) // 0x00000040 */ +#define DCTL_TCTL_Msk (0x7UL << DCTL_TCTL_Pos) // 0x00000070 +#define DCTL_TCTL DCTL_TCTL_Msk // Test control +#define DCTL_TCTL_0 (0x1UL << DCTL_TCTL_Pos) // 0x00000010 +#define DCTL_TCTL_1 (0x2UL << DCTL_TCTL_Pos) // 0x00000020 +#define DCTL_TCTL_2 (0x4UL << DCTL_TCTL_Pos) // 0x00000040 #define DCTL_SGINAK_Pos (7U) -#define DCTL_SGINAK_Msk (0x1UL << DCTL_SGINAK_Pos) // 0x00000080 */ -#define DCTL_SGINAK DCTL_SGINAK_Msk // Set global IN NAK */ +#define DCTL_SGINAK_Msk (0x1UL << DCTL_SGINAK_Pos) // 0x00000080 +#define DCTL_SGINAK DCTL_SGINAK_Msk // Set global IN NAK #define DCTL_CGINAK_Pos (8U) -#define DCTL_CGINAK_Msk (0x1UL << DCTL_CGINAK_Pos) // 0x00000100 */ -#define DCTL_CGINAK DCTL_CGINAK_Msk // Clear global IN NAK */ +#define DCTL_CGINAK_Msk (0x1UL << DCTL_CGINAK_Pos) // 0x00000100 +#define DCTL_CGINAK DCTL_CGINAK_Msk // Clear global IN NAK #define DCTL_SGONAK_Pos (9U) -#define DCTL_SGONAK_Msk (0x1UL << DCTL_SGONAK_Pos) // 0x00000200 */ -#define DCTL_SGONAK DCTL_SGONAK_Msk // Set global OUT NAK */ +#define DCTL_SGONAK_Msk (0x1UL << DCTL_SGONAK_Pos) // 0x00000200 +#define DCTL_SGONAK DCTL_SGONAK_Msk // Set global OUT NAK #define DCTL_CGONAK_Pos (10U) -#define DCTL_CGONAK_Msk (0x1UL << DCTL_CGONAK_Pos) // 0x00000400 */ -#define DCTL_CGONAK DCTL_CGONAK_Msk // Clear global OUT NAK */ +#define DCTL_CGONAK_Msk (0x1UL << DCTL_CGONAK_Pos) // 0x00000400 +#define DCTL_CGONAK DCTL_CGONAK_Msk // Clear global OUT NAK #define DCTL_POPRGDNE_Pos (11U) -#define DCTL_POPRGDNE_Msk (0x1UL << DCTL_POPRGDNE_Pos) // 0x00000800 */ -#define DCTL_POPRGDNE DCTL_POPRGDNE_Msk // Power-on programming done */ +#define DCTL_POPRGDNE_Msk (0x1UL << DCTL_POPRGDNE_Pos) // 0x00000800 +#define DCTL_POPRGDNE DCTL_POPRGDNE_Msk // Power-on programming done /******************** Bit definition for HFIR register ********************/ #define HFIR_FRIVL_Pos (0U) -#define HFIR_FRIVL_Msk (0xFFFFUL << HFIR_FRIVL_Pos) // 0x0000FFFF */ -#define HFIR_FRIVL HFIR_FRIVL_Msk // Frame interval */ +#define HFIR_FRIVL_Msk (0xFFFFUL << HFIR_FRIVL_Pos) // 0x0000FFFF +#define HFIR_FRIVL HFIR_FRIVL_Msk // Frame interval /******************** Bit definition for HFNUM register ********************/ #define HFNUM_FRNUM_Pos (0U) -#define HFNUM_FRNUM_Msk (0xFFFFUL << HFNUM_FRNUM_Pos) // 0x0000FFFF */ -#define HFNUM_FRNUM HFNUM_FRNUM_Msk // Frame number */ +#define HFNUM_FRNUM_Msk (0xFFFFUL << HFNUM_FRNUM_Pos) // 0x0000FFFF +#define HFNUM_FRNUM HFNUM_FRNUM_Msk // Frame number #define HFNUM_FTREM_Pos (16U) -#define HFNUM_FTREM_Msk (0xFFFFUL << HFNUM_FTREM_Pos) // 0xFFFF0000 */ -#define HFNUM_FTREM HFNUM_FTREM_Msk // Frame time remaining */ +#define HFNUM_FTREM_Msk (0xFFFFUL << HFNUM_FTREM_Pos) // 0xFFFF0000 +#define HFNUM_FTREM HFNUM_FTREM_Msk // Frame time remaining /******************** Bit definition for DSTS register ********************/ #define DSTS_SUSPSTS_Pos (0U) -#define DSTS_SUSPSTS_Msk (0x1UL << DSTS_SUSPSTS_Pos) // 0x00000001 */ -#define DSTS_SUSPSTS DSTS_SUSPSTS_Msk // Suspend status */ +#define DSTS_SUSPSTS_Msk (0x1UL << DSTS_SUSPSTS_Pos) // 0x00000001 +#define DSTS_SUSPSTS DSTS_SUSPSTS_Msk // Suspend status #define DSTS_ENUMSPD_Pos (1U) -#define DSTS_ENUMSPD_Msk (0x3UL << DSTS_ENUMSPD_Pos) // 0x00000006 */ -#define DSTS_ENUMSPD DSTS_ENUMSPD_Msk // Enumerated speed */ +#define DSTS_ENUMSPD_Msk (0x3UL << DSTS_ENUMSPD_Pos) // 0x00000006 +#define DSTS_ENUMSPD DSTS_ENUMSPD_Msk // Enumerated speed #define DSTS_ENUMSPD_HS 0 // Highspeed #define DSTS_ENUMSPD_FS_HSPHY 1 // Fullspeed on HS PHY #define DSTS_ENUMSPD_LS 2 // Lowspeed @@ -499,427 +499,427 @@ TU_VERIFY_STATIC(offsetof(dwc2_regs_t, fifo ) == 0x1000, "incorrect size"); #define DSTS_EERR_Pos (3U) -#define DSTS_EERR_Msk (0x1UL << DSTS_EERR_Pos) // 0x00000008 */ -#define DSTS_EERR DSTS_EERR_Msk // Erratic error */ +#define DSTS_EERR_Msk (0x1UL << DSTS_EERR_Pos) // 0x00000008 +#define DSTS_EERR DSTS_EERR_Msk // Erratic error #define DSTS_FNSOF_Pos (8U) -#define DSTS_FNSOF_Msk (0x3FFFUL << DSTS_FNSOF_Pos) // 0x003FFF00 */ -#define DSTS_FNSOF DSTS_FNSOF_Msk // Frame number of the received SOF */ +#define DSTS_FNSOF_Msk (0x3FFFUL << DSTS_FNSOF_Pos) // 0x003FFF00 +#define DSTS_FNSOF DSTS_FNSOF_Msk // Frame number of the received SOF /******************** Bit definition for GAHBCFG register ********************/ #define GAHBCFG_GINT_Pos (0U) -#define GAHBCFG_GINT_Msk (0x1UL << GAHBCFG_GINT_Pos) // 0x00000001 */ -#define GAHBCFG_GINT GAHBCFG_GINT_Msk // Global interrupt mask */ +#define GAHBCFG_GINT_Msk (0x1UL << GAHBCFG_GINT_Pos) // 0x00000001 +#define GAHBCFG_GINT GAHBCFG_GINT_Msk // Global interrupt mask #define GAHBCFG_HBSTLEN_Pos (1U) -#define GAHBCFG_HBSTLEN_Msk (0xFUL << GAHBCFG_HBSTLEN_Pos) // 0x0000001E */ -#define GAHBCFG_HBSTLEN GAHBCFG_HBSTLEN_Msk // Burst length/type */ -#define GAHBCFG_HBSTLEN_0 (0x0UL << GAHBCFG_HBSTLEN_Pos) // Single */ -#define GAHBCFG_HBSTLEN_1 (0x1UL << GAHBCFG_HBSTLEN_Pos) // INCR */ -#define GAHBCFG_HBSTLEN_2 (0x3UL << GAHBCFG_HBSTLEN_Pos) // INCR4 */ -#define GAHBCFG_HBSTLEN_3 (0x5UL << GAHBCFG_HBSTLEN_Pos) // INCR8 */ -#define GAHBCFG_HBSTLEN_4 (0x7UL << GAHBCFG_HBSTLEN_Pos) // INCR16 */ +#define GAHBCFG_HBSTLEN_Msk (0xFUL << GAHBCFG_HBSTLEN_Pos) // 0x0000001E +#define GAHBCFG_HBSTLEN GAHBCFG_HBSTLEN_Msk // Burst length/type +#define GAHBCFG_HBSTLEN_0 (0x0UL << GAHBCFG_HBSTLEN_Pos) // Single +#define GAHBCFG_HBSTLEN_1 (0x1UL << GAHBCFG_HBSTLEN_Pos) // INCR +#define GAHBCFG_HBSTLEN_2 (0x3UL << GAHBCFG_HBSTLEN_Pos) // INCR4 +#define GAHBCFG_HBSTLEN_3 (0x5UL << GAHBCFG_HBSTLEN_Pos) // INCR8 +#define GAHBCFG_HBSTLEN_4 (0x7UL << GAHBCFG_HBSTLEN_Pos) // INCR16 #define GAHBCFG_DMAEN_Pos (5U) -#define GAHBCFG_DMAEN_Msk (0x1UL << GAHBCFG_DMAEN_Pos) // 0x00000020 */ -#define GAHBCFG_DMAEN GAHBCFG_DMAEN_Msk // DMA enable */ +#define GAHBCFG_DMAEN_Msk (0x1UL << GAHBCFG_DMAEN_Pos) // 0x00000020 +#define GAHBCFG_DMAEN GAHBCFG_DMAEN_Msk // DMA enable #define GAHBCFG_TXFELVL_Pos (7U) -#define GAHBCFG_TXFELVL_Msk (0x1UL << GAHBCFG_TXFELVL_Pos) // 0x00000080 */ -#define GAHBCFG_TXFELVL GAHBCFG_TXFELVL_Msk // TxFIFO empty level */ +#define GAHBCFG_TXFELVL_Msk (0x1UL << GAHBCFG_TXFELVL_Pos) // 0x00000080 +#define GAHBCFG_TXFELVL GAHBCFG_TXFELVL_Msk // TxFIFO empty level #define GAHBCFG_PTXFELVL_Pos (8U) -#define GAHBCFG_PTXFELVL_Msk (0x1UL << GAHBCFG_PTXFELVL_Pos) // 0x00000100 */ -#define GAHBCFG_PTXFELVL GAHBCFG_PTXFELVL_Msk // Periodic TxFIFO empty level */ +#define GAHBCFG_PTXFELVL_Msk (0x1UL << GAHBCFG_PTXFELVL_Pos) // 0x00000100 +#define GAHBCFG_PTXFELVL GAHBCFG_PTXFELVL_Msk // Periodic TxFIFO empty level #define GSNPSID_ID_MASK TU_GENMASK(31, 16) /******************** Bit definition for GUSBCFG register ********************/ #define GUSBCFG_TOCAL_Pos (0U) -#define GUSBCFG_TOCAL_Msk (0x7UL << GUSBCFG_TOCAL_Pos) // 0x00000007 */ -#define GUSBCFG_TOCAL GUSBCFG_TOCAL_Msk // FS timeout calibration */ +#define GUSBCFG_TOCAL_Msk (0x7UL << GUSBCFG_TOCAL_Pos) // 0x00000007 +#define GUSBCFG_TOCAL GUSBCFG_TOCAL_Msk // FS timeout calibration #define GUSBCFG_PHYIF16_Pos (3U) -#define GUSBCFG_PHYIF16_Msk (0x1UL << GUSBCFG_PHYIF16_Pos) // 0x00000008 */ -#define GUSBCFG_PHYIF16 GUSBCFG_PHYIF16_Msk // PHY Interface (PHYIf) */ +#define GUSBCFG_PHYIF16_Msk (0x1UL << GUSBCFG_PHYIF16_Pos) // 0x00000008 +#define GUSBCFG_PHYIF16 GUSBCFG_PHYIF16_Msk // PHY Interface (PHYIf) #define GUSBCFG_ULPI_UTMI_SEL_Pos (4U) -#define GUSBCFG_ULPI_UTMI_SEL_Msk (0x1UL << GUSBCFG_ULPI_UTMI_SEL_Pos) // 0x00000010 */ -#define GUSBCFG_ULPI_UTMI_SEL GUSBCFG_ULPI_UTMI_SEL_Msk // ULPI or UTMI+ Select (ULPI_UTMI_Sel) */ +#define GUSBCFG_ULPI_UTMI_SEL_Msk (0x1UL << GUSBCFG_ULPI_UTMI_SEL_Pos) // 0x00000010 +#define GUSBCFG_ULPI_UTMI_SEL GUSBCFG_ULPI_UTMI_SEL_Msk // ULPI or UTMI+ Select (ULPI_UTMI_Sel) #define GUSBCFG_PHYSEL_Pos (6U) -#define GUSBCFG_PHYSEL_Msk (0x1UL << GUSBCFG_PHYSEL_Pos) // 0x00000040 */ -#define GUSBCFG_PHYSEL GUSBCFG_PHYSEL_Msk // USB 2.0 high-speed ULPI PHY or USB 1.1 full-speed serial transceiver select */ +#define GUSBCFG_PHYSEL_Msk (0x1UL << GUSBCFG_PHYSEL_Pos) // 0x00000040 +#define GUSBCFG_PHYSEL GUSBCFG_PHYSEL_Msk // USB 2.0 high-speed ULPI PHY or USB 1.1 full-speed serial transceiver select #define GUSBCFG_DDRSEL TU_BIT(7) // Single Data Rate (SDR) or Double Data Rate (DDR) or ULPI interface. #define GUSBCFG_SRPCAP_Pos (8U) -#define GUSBCFG_SRPCAP_Msk (0x1UL << GUSBCFG_SRPCAP_Pos) // 0x00000100 */ -#define GUSBCFG_SRPCAP GUSBCFG_SRPCAP_Msk // SRP-capable */ +#define GUSBCFG_SRPCAP_Msk (0x1UL << GUSBCFG_SRPCAP_Pos) // 0x00000100 +#define GUSBCFG_SRPCAP GUSBCFG_SRPCAP_Msk // SRP-capable #define GUSBCFG_HNPCAP_Pos (9U) -#define GUSBCFG_HNPCAP_Msk (0x1UL << GUSBCFG_HNPCAP_Pos) // 0x00000200 */ -#define GUSBCFG_HNPCAP GUSBCFG_HNPCAP_Msk // HNP-capable */ +#define GUSBCFG_HNPCAP_Msk (0x1UL << GUSBCFG_HNPCAP_Pos) // 0x00000200 +#define GUSBCFG_HNPCAP GUSBCFG_HNPCAP_Msk // HNP-capable #define GUSBCFG_TRDT_Pos (10U) -#define GUSBCFG_TRDT_Msk (0xFUL << GUSBCFG_TRDT_Pos) // 0x00003C00 */ -#define GUSBCFG_TRDT GUSBCFG_TRDT_Msk // USB turnaround time */ +#define GUSBCFG_TRDT_Msk (0xFUL << GUSBCFG_TRDT_Pos) // 0x00003C00 +#define GUSBCFG_TRDT GUSBCFG_TRDT_Msk // USB turnaround time #define GUSBCFG_PHYLPCS_Pos (15U) -#define GUSBCFG_PHYLPCS_Msk (0x1UL << GUSBCFG_PHYLPCS_Pos) // 0x00008000 */ -#define GUSBCFG_PHYLPCS GUSBCFG_PHYLPCS_Msk // PHY Low-power clock select */ +#define GUSBCFG_PHYLPCS_Msk (0x1UL << GUSBCFG_PHYLPCS_Pos) // 0x00008000 +#define GUSBCFG_PHYLPCS GUSBCFG_PHYLPCS_Msk // PHY Low-power clock select #define GUSBCFG_ULPIFSLS_Pos (17U) -#define GUSBCFG_ULPIFSLS_Msk (0x1UL << GUSBCFG_ULPIFSLS_Pos) // 0x00020000 */ -#define GUSBCFG_ULPIFSLS GUSBCFG_ULPIFSLS_Msk // ULPI FS/LS select */ +#define GUSBCFG_ULPIFSLS_Msk (0x1UL << GUSBCFG_ULPIFSLS_Pos) // 0x00020000 +#define GUSBCFG_ULPIFSLS GUSBCFG_ULPIFSLS_Msk // ULPI FS/LS select #define GUSBCFG_ULPIAR_Pos (18U) -#define GUSBCFG_ULPIAR_Msk (0x1UL << GUSBCFG_ULPIAR_Pos) // 0x00040000 */ -#define GUSBCFG_ULPIAR GUSBCFG_ULPIAR_Msk // ULPI Auto-resume */ +#define GUSBCFG_ULPIAR_Msk (0x1UL << GUSBCFG_ULPIAR_Pos) // 0x00040000 +#define GUSBCFG_ULPIAR GUSBCFG_ULPIAR_Msk // ULPI Auto-resume #define GUSBCFG_ULPICSM_Pos (19U) -#define GUSBCFG_ULPICSM_Msk (0x1UL << GUSBCFG_ULPICSM_Pos) // 0x00080000 */ -#define GUSBCFG_ULPICSM GUSBCFG_ULPICSM_Msk // ULPI Clock SuspendM */ +#define GUSBCFG_ULPICSM_Msk (0x1UL << GUSBCFG_ULPICSM_Pos) // 0x00080000 +#define GUSBCFG_ULPICSM GUSBCFG_ULPICSM_Msk // ULPI Clock SuspendM #define GUSBCFG_ULPIEVBUSD_Pos (20U) -#define GUSBCFG_ULPIEVBUSD_Msk (0x1UL << GUSBCFG_ULPIEVBUSD_Pos) // 0x00100000 */ -#define GUSBCFG_ULPIEVBUSD GUSBCFG_ULPIEVBUSD_Msk // ULPI External VBUS Drive */ +#define GUSBCFG_ULPIEVBUSD_Msk (0x1UL << GUSBCFG_ULPIEVBUSD_Pos) // 0x00100000 +#define GUSBCFG_ULPIEVBUSD GUSBCFG_ULPIEVBUSD_Msk // ULPI External VBUS Drive #define GUSBCFG_ULPIEVBUSI_Pos (21U) -#define GUSBCFG_ULPIEVBUSI_Msk (0x1UL << GUSBCFG_ULPIEVBUSI_Pos) // 0x00200000 */ -#define GUSBCFG_ULPIEVBUSI GUSBCFG_ULPIEVBUSI_Msk // ULPI external VBUS indicator */ +#define GUSBCFG_ULPIEVBUSI_Msk (0x1UL << GUSBCFG_ULPIEVBUSI_Pos) // 0x00200000 +#define GUSBCFG_ULPIEVBUSI GUSBCFG_ULPIEVBUSI_Msk // ULPI external VBUS indicator #define GUSBCFG_TSDPS_Pos (22U) -#define GUSBCFG_TSDPS_Msk (0x1UL << GUSBCFG_TSDPS_Pos) // 0x00400000 */ -#define GUSBCFG_TSDPS GUSBCFG_TSDPS_Msk // TermSel DLine pulsing selection */ +#define GUSBCFG_TSDPS_Msk (0x1UL << GUSBCFG_TSDPS_Pos) // 0x00400000 +#define GUSBCFG_TSDPS GUSBCFG_TSDPS_Msk // TermSel DLine pulsing selection #define GUSBCFG_PCCI_Pos (23U) -#define GUSBCFG_PCCI_Msk (0x1UL << GUSBCFG_PCCI_Pos) // 0x00800000 */ -#define GUSBCFG_PCCI GUSBCFG_PCCI_Msk // Indicator complement */ +#define GUSBCFG_PCCI_Msk (0x1UL << GUSBCFG_PCCI_Pos) // 0x00800000 +#define GUSBCFG_PCCI GUSBCFG_PCCI_Msk // Indicator complement #define GUSBCFG_PTCI_Pos (24U) -#define GUSBCFG_PTCI_Msk (0x1UL << GUSBCFG_PTCI_Pos) // 0x01000000 */ -#define GUSBCFG_PTCI GUSBCFG_PTCI_Msk // Indicator pass through */ +#define GUSBCFG_PTCI_Msk (0x1UL << GUSBCFG_PTCI_Pos) // 0x01000000 +#define GUSBCFG_PTCI GUSBCFG_PTCI_Msk // Indicator pass through #define GUSBCFG_ULPIIPD_Pos (25U) -#define GUSBCFG_ULPIIPD_Msk (0x1UL << GUSBCFG_ULPIIPD_Pos) // 0x02000000 */ -#define GUSBCFG_ULPIIPD GUSBCFG_ULPIIPD_Msk // ULPI interface protect disable */ +#define GUSBCFG_ULPIIPD_Msk (0x1UL << GUSBCFG_ULPIIPD_Pos) // 0x02000000 +#define GUSBCFG_ULPIIPD GUSBCFG_ULPIIPD_Msk // ULPI interface protect disable #define GUSBCFG_FHMOD_Pos (29U) -#define GUSBCFG_FHMOD_Msk (0x1UL << GUSBCFG_FHMOD_Pos) // 0x20000000 */ -#define GUSBCFG_FHMOD GUSBCFG_FHMOD_Msk // Forced host mode */ +#define GUSBCFG_FHMOD_Msk (0x1UL << GUSBCFG_FHMOD_Pos) // 0x20000000 +#define GUSBCFG_FHMOD GUSBCFG_FHMOD_Msk // Forced host mode #define GUSBCFG_FDMOD_Pos (30U) -#define GUSBCFG_FDMOD_Msk (0x1UL << GUSBCFG_FDMOD_Pos) // 0x40000000 */ -#define GUSBCFG_FDMOD GUSBCFG_FDMOD_Msk // Forced peripheral mode */ +#define GUSBCFG_FDMOD_Msk (0x1UL << GUSBCFG_FDMOD_Pos) // 0x40000000 +#define GUSBCFG_FDMOD GUSBCFG_FDMOD_Msk // Forced peripheral mode #define GUSBCFG_CTXPKT_Pos (31U) -#define GUSBCFG_CTXPKT_Msk (0x1UL << GUSBCFG_CTXPKT_Pos) // 0x80000000 */ -#define GUSBCFG_CTXPKT GUSBCFG_CTXPKT_Msk // Corrupt Tx packet */ +#define GUSBCFG_CTXPKT_Msk (0x1UL << GUSBCFG_CTXPKT_Pos) // 0x80000000 +#define GUSBCFG_CTXPKT GUSBCFG_CTXPKT_Msk // Corrupt Tx packet /******************** Bit definition for GRSTCTL register ********************/ #define GRSTCTL_CSRST_Pos (0U) -#define GRSTCTL_CSRST_Msk (0x1UL << GRSTCTL_CSRST_Pos) // 0x00000001 */ -#define GRSTCTL_CSRST GRSTCTL_CSRST_Msk // Core soft reset */ +#define GRSTCTL_CSRST_Msk (0x1UL << GRSTCTL_CSRST_Pos) // 0x00000001 +#define GRSTCTL_CSRST GRSTCTL_CSRST_Msk // Core soft reset #define GRSTCTL_HSRST_Pos (1U) -#define GRSTCTL_HSRST_Msk (0x1UL << GRSTCTL_HSRST_Pos) // 0x00000002 */ -#define GRSTCTL_HSRST GRSTCTL_HSRST_Msk // HCLK soft reset */ +#define GRSTCTL_HSRST_Msk (0x1UL << GRSTCTL_HSRST_Pos) // 0x00000002 +#define GRSTCTL_HSRST GRSTCTL_HSRST_Msk // HCLK soft reset #define GRSTCTL_FCRST_Pos (2U) -#define GRSTCTL_FCRST_Msk (0x1UL << GRSTCTL_FCRST_Pos) // 0x00000004 */ -#define GRSTCTL_FCRST GRSTCTL_FCRST_Msk // Host frame counter reset */ +#define GRSTCTL_FCRST_Msk (0x1UL << GRSTCTL_FCRST_Pos) // 0x00000004 +#define GRSTCTL_FCRST GRSTCTL_FCRST_Msk // Host frame counter reset #define GRSTCTL_RXFFLSH_Pos (4U) -#define GRSTCTL_RXFFLSH_Msk (0x1UL << GRSTCTL_RXFFLSH_Pos) // 0x00000010 */ -#define GRSTCTL_RXFFLSH GRSTCTL_RXFFLSH_Msk // RxFIFO flush */ +#define GRSTCTL_RXFFLSH_Msk (0x1UL << GRSTCTL_RXFFLSH_Pos) // 0x00000010 +#define GRSTCTL_RXFFLSH GRSTCTL_RXFFLSH_Msk // RxFIFO flush #define GRSTCTL_TXFFLSH_Pos (5U) -#define GRSTCTL_TXFFLSH_Msk (0x1UL << GRSTCTL_TXFFLSH_Pos) // 0x00000020 */ -#define GRSTCTL_TXFFLSH GRSTCTL_TXFFLSH_Msk // TxFIFO flush */ +#define GRSTCTL_TXFFLSH_Msk (0x1UL << GRSTCTL_TXFFLSH_Pos) // 0x00000020 +#define GRSTCTL_TXFFLSH GRSTCTL_TXFFLSH_Msk // TxFIFO flush #define GRSTCTL_TXFNUM_Pos (6U) -#define GRSTCTL_TXFNUM_Msk (0x1FUL << GRSTCTL_TXFNUM_Pos) // 0x000007C0 */ -#define GRSTCTL_TXFNUM GRSTCTL_TXFNUM_Msk // TxFIFO number */ -#define GRSTCTL_TXFNUM_0 (0x01UL << GRSTCTL_TXFNUM_Pos) // 0x00000040 */ -#define GRSTCTL_TXFNUM_1 (0x02UL << GRSTCTL_TXFNUM_Pos) // 0x00000080 */ -#define GRSTCTL_TXFNUM_2 (0x04UL << GRSTCTL_TXFNUM_Pos) // 0x00000100 */ -#define GRSTCTL_TXFNUM_3 (0x08UL << GRSTCTL_TXFNUM_Pos) // 0x00000200 */ -#define GRSTCTL_TXFNUM_4 (0x10UL << GRSTCTL_TXFNUM_Pos) // 0x00000400 */ +#define GRSTCTL_TXFNUM_Msk (0x1FUL << GRSTCTL_TXFNUM_Pos) // 0x000007C0 +#define GRSTCTL_TXFNUM GRSTCTL_TXFNUM_Msk // TxFIFO number +#define GRSTCTL_TXFNUM_0 (0x01UL << GRSTCTL_TXFNUM_Pos) // 0x00000040 +#define GRSTCTL_TXFNUM_1 (0x02UL << GRSTCTL_TXFNUM_Pos) // 0x00000080 +#define GRSTCTL_TXFNUM_2 (0x04UL << GRSTCTL_TXFNUM_Pos) // 0x00000100 +#define GRSTCTL_TXFNUM_3 (0x08UL << GRSTCTL_TXFNUM_Pos) // 0x00000200 +#define GRSTCTL_TXFNUM_4 (0x10UL << GRSTCTL_TXFNUM_Pos) // 0x00000400 #define GRSTCTL_CSFTRST_DONE_Pos (29) #define GRSTCTL_CSFTRST_DONE (1u << GRSTCTL_CSFTRST_DONE_Pos) // Reset Done, only available from v4.20a #define GRSTCTL_DMAREQ_Pos (30U) -#define GRSTCTL_DMAREQ_Msk (0x1UL << GRSTCTL_DMAREQ_Pos) // 0x40000000 */ -#define GRSTCTL_DMAREQ GRSTCTL_DMAREQ_Msk // DMA request signal */ +#define GRSTCTL_DMAREQ_Msk (0x1UL << GRSTCTL_DMAREQ_Pos) // 0x40000000 +#define GRSTCTL_DMAREQ GRSTCTL_DMAREQ_Msk // DMA request signal #define GRSTCTL_AHBIDL_Pos (31U) -#define GRSTCTL_AHBIDL_Msk (0x1UL << GRSTCTL_AHBIDL_Pos) // 0x80000000 */ -#define GRSTCTL_AHBIDL GRSTCTL_AHBIDL_Msk // AHB master idle */ +#define GRSTCTL_AHBIDL_Msk (0x1UL << GRSTCTL_AHBIDL_Pos) // 0x80000000 +#define GRSTCTL_AHBIDL GRSTCTL_AHBIDL_Msk // AHB master idle /******************** Bit definition for DIEPMSK register ********************/ #define DIEPMSK_XFRCM_Pos (0U) -#define DIEPMSK_XFRCM_Msk (0x1UL << DIEPMSK_XFRCM_Pos) // 0x00000001 */ -#define DIEPMSK_XFRCM DIEPMSK_XFRCM_Msk // Transfer completed interrupt mask */ +#define DIEPMSK_XFRCM_Msk (0x1UL << DIEPMSK_XFRCM_Pos) // 0x00000001 +#define DIEPMSK_XFRCM DIEPMSK_XFRCM_Msk // Transfer completed interrupt mask #define DIEPMSK_EPDM_Pos (1U) -#define DIEPMSK_EPDM_Msk (0x1UL << DIEPMSK_EPDM_Pos) // 0x00000002 */ -#define DIEPMSK_EPDM DIEPMSK_EPDM_Msk // Endpoint disabled interrupt mask */ +#define DIEPMSK_EPDM_Msk (0x1UL << DIEPMSK_EPDM_Pos) // 0x00000002 +#define DIEPMSK_EPDM DIEPMSK_EPDM_Msk // Endpoint disabled interrupt mask #define DIEPMSK_TOM_Pos (3U) -#define DIEPMSK_TOM_Msk (0x1UL << DIEPMSK_TOM_Pos) // 0x00000008 */ -#define DIEPMSK_TOM DIEPMSK_TOM_Msk // Timeout condition mask (nonisochronous endpoints) */ +#define DIEPMSK_TOM_Msk (0x1UL << DIEPMSK_TOM_Pos) // 0x00000008 +#define DIEPMSK_TOM DIEPMSK_TOM_Msk // Timeout condition mask (nonisochronous endpoints) #define DIEPMSK_ITTXFEMSK_Pos (4U) -#define DIEPMSK_ITTXFEMSK_Msk (0x1UL << DIEPMSK_ITTXFEMSK_Pos) // 0x00000010 */ -#define DIEPMSK_ITTXFEMSK DIEPMSK_ITTXFEMSK_Msk // IN token received when TxFIFO empty mask */ +#define DIEPMSK_ITTXFEMSK_Msk (0x1UL << DIEPMSK_ITTXFEMSK_Pos) // 0x00000010 +#define DIEPMSK_ITTXFEMSK DIEPMSK_ITTXFEMSK_Msk // IN token received when TxFIFO empty mask #define DIEPMSK_INEPNMM_Pos (5U) -#define DIEPMSK_INEPNMM_Msk (0x1UL << DIEPMSK_INEPNMM_Pos) // 0x00000020 */ -#define DIEPMSK_INEPNMM DIEPMSK_INEPNMM_Msk // IN token received with EP mismatch mask */ +#define DIEPMSK_INEPNMM_Msk (0x1UL << DIEPMSK_INEPNMM_Pos) // 0x00000020 +#define DIEPMSK_INEPNMM DIEPMSK_INEPNMM_Msk // IN token received with EP mismatch mask #define DIEPMSK_INEPNEM_Pos (6U) -#define DIEPMSK_INEPNEM_Msk (0x1UL << DIEPMSK_INEPNEM_Pos) // 0x00000040 */ -#define DIEPMSK_INEPNEM DIEPMSK_INEPNEM_Msk // IN endpoint NAK effective mask */ +#define DIEPMSK_INEPNEM_Msk (0x1UL << DIEPMSK_INEPNEM_Pos) // 0x00000040 +#define DIEPMSK_INEPNEM DIEPMSK_INEPNEM_Msk // IN endpoint NAK effective mask #define DIEPMSK_TXFURM_Pos (8U) -#define DIEPMSK_TXFURM_Msk (0x1UL << DIEPMSK_TXFURM_Pos) // 0x00000100 */ -#define DIEPMSK_TXFURM DIEPMSK_TXFURM_Msk // FIFO underrun mask */ +#define DIEPMSK_TXFURM_Msk (0x1UL << DIEPMSK_TXFURM_Pos) // 0x00000100 +#define DIEPMSK_TXFURM DIEPMSK_TXFURM_Msk // FIFO underrun mask #define DIEPMSK_BIM_Pos (9U) -#define DIEPMSK_BIM_Msk (0x1UL << DIEPMSK_BIM_Pos) // 0x00000200 */ -#define DIEPMSK_BIM DIEPMSK_BIM_Msk // BNA interrupt mask */ +#define DIEPMSK_BIM_Msk (0x1UL << DIEPMSK_BIM_Pos) // 0x00000200 +#define DIEPMSK_BIM DIEPMSK_BIM_Msk // BNA interrupt mask /******************** Bit definition for HPTXSTS register ********************/ #define HPTXSTS_PTXFSAVL_Pos (0U) -#define HPTXSTS_PTXFSAVL_Msk (0xFFFFUL << HPTXSTS_PTXFSAVL_Pos) // 0x0000FFFF */ -#define HPTXSTS_PTXFSAVL HPTXSTS_PTXFSAVL_Msk // Periodic transmit data FIFO space available */ +#define HPTXSTS_PTXFSAVL_Msk (0xFFFFUL << HPTXSTS_PTXFSAVL_Pos) // 0x0000FFFF +#define HPTXSTS_PTXFSAVL HPTXSTS_PTXFSAVL_Msk // Periodic transmit data FIFO space available #define HPTXSTS_PTXQSAV_Pos (16U) -#define HPTXSTS_PTXQSAV_Msk (0xFFUL << HPTXSTS_PTXQSAV_Pos) // 0x00FF0000 */ -#define HPTXSTS_PTXQSAV HPTXSTS_PTXQSAV_Msk // Periodic transmit request queue space available */ -#define HPTXSTS_PTXQSAV_0 (0x01UL << HPTXSTS_PTXQSAV_Pos) // 0x00010000 */ -#define HPTXSTS_PTXQSAV_1 (0x02UL << HPTXSTS_PTXQSAV_Pos) // 0x00020000 */ -#define HPTXSTS_PTXQSAV_2 (0x04UL << HPTXSTS_PTXQSAV_Pos) // 0x00040000 */ -#define HPTXSTS_PTXQSAV_3 (0x08UL << HPTXSTS_PTXQSAV_Pos) // 0x00080000 */ -#define HPTXSTS_PTXQSAV_4 (0x10UL << HPTXSTS_PTXQSAV_Pos) // 0x00100000 */ -#define HPTXSTS_PTXQSAV_5 (0x20UL << HPTXSTS_PTXQSAV_Pos) // 0x00200000 */ -#define HPTXSTS_PTXQSAV_6 (0x40UL << HPTXSTS_PTXQSAV_Pos) // 0x00400000 */ -#define HPTXSTS_PTXQSAV_7 (0x80UL << HPTXSTS_PTXQSAV_Pos) // 0x00800000 */ +#define HPTXSTS_PTXQSAV_Msk (0xFFUL << HPTXSTS_PTXQSAV_Pos) // 0x00FF0000 +#define HPTXSTS_PTXQSAV HPTXSTS_PTXQSAV_Msk // Periodic transmit request queue space available +#define HPTXSTS_PTXQSAV_0 (0x01UL << HPTXSTS_PTXQSAV_Pos) // 0x00010000 +#define HPTXSTS_PTXQSAV_1 (0x02UL << HPTXSTS_PTXQSAV_Pos) // 0x00020000 +#define HPTXSTS_PTXQSAV_2 (0x04UL << HPTXSTS_PTXQSAV_Pos) // 0x00040000 +#define HPTXSTS_PTXQSAV_3 (0x08UL << HPTXSTS_PTXQSAV_Pos) // 0x00080000 +#define HPTXSTS_PTXQSAV_4 (0x10UL << HPTXSTS_PTXQSAV_Pos) // 0x00100000 +#define HPTXSTS_PTXQSAV_5 (0x20UL << HPTXSTS_PTXQSAV_Pos) // 0x00200000 +#define HPTXSTS_PTXQSAV_6 (0x40UL << HPTXSTS_PTXQSAV_Pos) // 0x00400000 +#define HPTXSTS_PTXQSAV_7 (0x80UL << HPTXSTS_PTXQSAV_Pos) // 0x00800000 #define HPTXSTS_PTXQTOP_Pos (24U) -#define HPTXSTS_PTXQTOP_Msk (0xFFUL << HPTXSTS_PTXQTOP_Pos) // 0xFF000000 */ -#define HPTXSTS_PTXQTOP HPTXSTS_PTXQTOP_Msk // Top of the periodic transmit request queue */ -#define HPTXSTS_PTXQTOP_0 (0x01UL << HPTXSTS_PTXQTOP_Pos) // 0x01000000 */ -#define HPTXSTS_PTXQTOP_1 (0x02UL << HPTXSTS_PTXQTOP_Pos) // 0x02000000 */ -#define HPTXSTS_PTXQTOP_2 (0x04UL << HPTXSTS_PTXQTOP_Pos) // 0x04000000 */ -#define HPTXSTS_PTXQTOP_3 (0x08UL << HPTXSTS_PTXQTOP_Pos) // 0x08000000 */ -#define HPTXSTS_PTXQTOP_4 (0x10UL << HPTXSTS_PTXQTOP_Pos) // 0x10000000 */ -#define HPTXSTS_PTXQTOP_5 (0x20UL << HPTXSTS_PTXQTOP_Pos) // 0x20000000 */ -#define HPTXSTS_PTXQTOP_6 (0x40UL << HPTXSTS_PTXQTOP_Pos) // 0x40000000 */ -#define HPTXSTS_PTXQTOP_7 (0x80UL << HPTXSTS_PTXQTOP_Pos) // 0x80000000 */ +#define HPTXSTS_PTXQTOP_Msk (0xFFUL << HPTXSTS_PTXQTOP_Pos) // 0xFF000000 +#define HPTXSTS_PTXQTOP HPTXSTS_PTXQTOP_Msk // Top of the periodic transmit request queue +#define HPTXSTS_PTXQTOP_0 (0x01UL << HPTXSTS_PTXQTOP_Pos) // 0x01000000 +#define HPTXSTS_PTXQTOP_1 (0x02UL << HPTXSTS_PTXQTOP_Pos) // 0x02000000 +#define HPTXSTS_PTXQTOP_2 (0x04UL << HPTXSTS_PTXQTOP_Pos) // 0x04000000 +#define HPTXSTS_PTXQTOP_3 (0x08UL << HPTXSTS_PTXQTOP_Pos) // 0x08000000 +#define HPTXSTS_PTXQTOP_4 (0x10UL << HPTXSTS_PTXQTOP_Pos) // 0x10000000 +#define HPTXSTS_PTXQTOP_5 (0x20UL << HPTXSTS_PTXQTOP_Pos) // 0x20000000 +#define HPTXSTS_PTXQTOP_6 (0x40UL << HPTXSTS_PTXQTOP_Pos) // 0x40000000 +#define HPTXSTS_PTXQTOP_7 (0x80UL << HPTXSTS_PTXQTOP_Pos) // 0x80000000 /******************** Bit definition for HAINT register ********************/ #define HAINT_HAINT_Pos (0U) -#define HAINT_HAINT_Msk (0xFFFFUL << HAINT_HAINT_Pos) // 0x0000FFFF */ -#define HAINT_HAINT HAINT_HAINT_Msk // Channel interrupts */ +#define HAINT_HAINT_Msk (0xFFFFUL << HAINT_HAINT_Pos) // 0x0000FFFF +#define HAINT_HAINT HAINT_HAINT_Msk // Channel interrupts /******************** Bit definition for DOEPMSK register ********************/ #define DOEPMSK_XFRCM_Pos (0U) -#define DOEPMSK_XFRCM_Msk (0x1UL << DOEPMSK_XFRCM_Pos) // 0x00000001 */ -#define DOEPMSK_XFRCM DOEPMSK_XFRCM_Msk // Transfer completed interrupt mask */ +#define DOEPMSK_XFRCM_Msk (0x1UL << DOEPMSK_XFRCM_Pos) // 0x00000001 +#define DOEPMSK_XFRCM DOEPMSK_XFRCM_Msk // Transfer completed interrupt mask #define DOEPMSK_EPDM_Pos (1U) -#define DOEPMSK_EPDM_Msk (0x1UL << DOEPMSK_EPDM_Pos) // 0x00000002 */ -#define DOEPMSK_EPDM DOEPMSK_EPDM_Msk // Endpoint disabled interrupt mask */ +#define DOEPMSK_EPDM_Msk (0x1UL << DOEPMSK_EPDM_Pos) // 0x00000002 +#define DOEPMSK_EPDM DOEPMSK_EPDM_Msk // Endpoint disabled interrupt mask #define DOEPMSK_AHBERRM_Pos (2U) -#define DOEPMSK_AHBERRM_Msk (0x1UL << DOEPMSK_AHBERRM_Pos) // 0x00000004 */ -#define DOEPMSK_AHBERRM DOEPMSK_AHBERRM_Msk // OUT transaction AHB Error interrupt mask */ +#define DOEPMSK_AHBERRM_Msk (0x1UL << DOEPMSK_AHBERRM_Pos) // 0x00000004 +#define DOEPMSK_AHBERRM DOEPMSK_AHBERRM_Msk // OUT transaction AHB Error interrupt mask #define DOEPMSK_STUPM_Pos (3U) -#define DOEPMSK_STUPM_Msk (0x1UL << DOEPMSK_STUPM_Pos) // 0x00000008 */ -#define DOEPMSK_STUPM DOEPMSK_STUPM_Msk // SETUP phase done mask */ +#define DOEPMSK_STUPM_Msk (0x1UL << DOEPMSK_STUPM_Pos) // 0x00000008 +#define DOEPMSK_STUPM DOEPMSK_STUPM_Msk // SETUP phase done mask #define DOEPMSK_OTEPDM_Pos (4U) -#define DOEPMSK_OTEPDM_Msk (0x1UL << DOEPMSK_OTEPDM_Pos) // 0x00000010 */ -#define DOEPMSK_OTEPDM DOEPMSK_OTEPDM_Msk // OUT token received when endpoint disabled mask */ +#define DOEPMSK_OTEPDM_Msk (0x1UL << DOEPMSK_OTEPDM_Pos) // 0x00000010 +#define DOEPMSK_OTEPDM DOEPMSK_OTEPDM_Msk // OUT token received when endpoint disabled mask #define DOEPMSK_OTEPSPRM_Pos (5U) -#define DOEPMSK_OTEPSPRM_Msk (0x1UL << DOEPMSK_OTEPSPRM_Pos) // 0x00000020 */ -#define DOEPMSK_OTEPSPRM DOEPMSK_OTEPSPRM_Msk // Status Phase Received mask */ +#define DOEPMSK_OTEPSPRM_Msk (0x1UL << DOEPMSK_OTEPSPRM_Pos) // 0x00000020 +#define DOEPMSK_OTEPSPRM DOEPMSK_OTEPSPRM_Msk // Status Phase Received mask #define DOEPMSK_B2BSTUP_Pos (6U) -#define DOEPMSK_B2BSTUP_Msk (0x1UL << DOEPMSK_B2BSTUP_Pos) // 0x00000040 */ -#define DOEPMSK_B2BSTUP DOEPMSK_B2BSTUP_Msk // Back-to-back SETUP packets received mask */ +#define DOEPMSK_B2BSTUP_Msk (0x1UL << DOEPMSK_B2BSTUP_Pos) // 0x00000040 +#define DOEPMSK_B2BSTUP DOEPMSK_B2BSTUP_Msk // Back-to-back SETUP packets received mask #define DOEPMSK_OPEM_Pos (8U) -#define DOEPMSK_OPEM_Msk (0x1UL << DOEPMSK_OPEM_Pos) // 0x00000100 */ -#define DOEPMSK_OPEM DOEPMSK_OPEM_Msk // OUT packet error mask */ +#define DOEPMSK_OPEM_Msk (0x1UL << DOEPMSK_OPEM_Pos) // 0x00000100 +#define DOEPMSK_OPEM DOEPMSK_OPEM_Msk // OUT packet error mask #define DOEPMSK_BOIM_Pos (9U) -#define DOEPMSK_BOIM_Msk (0x1UL << DOEPMSK_BOIM_Pos) // 0x00000200 */ -#define DOEPMSK_BOIM DOEPMSK_BOIM_Msk // BNA interrupt mask */ +#define DOEPMSK_BOIM_Msk (0x1UL << DOEPMSK_BOIM_Pos) // 0x00000200 +#define DOEPMSK_BOIM DOEPMSK_BOIM_Msk // BNA interrupt mask #define DOEPMSK_BERRM_Pos (12U) -#define DOEPMSK_BERRM_Msk (0x1UL << DOEPMSK_BERRM_Pos) // 0x00001000 */ -#define DOEPMSK_BERRM DOEPMSK_BERRM_Msk // Babble error interrupt mask */ +#define DOEPMSK_BERRM_Msk (0x1UL << DOEPMSK_BERRM_Pos) // 0x00001000 +#define DOEPMSK_BERRM DOEPMSK_BERRM_Msk // Babble error interrupt mask #define DOEPMSK_NAKM_Pos (13U) -#define DOEPMSK_NAKM_Msk (0x1UL << DOEPMSK_NAKM_Pos) // 0x00002000 */ -#define DOEPMSK_NAKM DOEPMSK_NAKM_Msk // OUT Packet NAK interrupt mask */ +#define DOEPMSK_NAKM_Msk (0x1UL << DOEPMSK_NAKM_Pos) // 0x00002000 +#define DOEPMSK_NAKM DOEPMSK_NAKM_Msk // OUT Packet NAK interrupt mask #define DOEPMSK_NYETM_Pos (14U) -#define DOEPMSK_NYETM_Msk (0x1UL << DOEPMSK_NYETM_Pos) // 0x00004000 */ -#define DOEPMSK_NYETM DOEPMSK_NYETM_Msk // NYET interrupt mask */ +#define DOEPMSK_NYETM_Msk (0x1UL << DOEPMSK_NYETM_Pos) // 0x00004000 +#define DOEPMSK_NYETM DOEPMSK_NYETM_Msk // NYET interrupt mask /******************** Bit definition for GINTSTS register ********************/ #define GINTSTS_CMOD_Pos (0U) -#define GINTSTS_CMOD_Msk (0x1UL << GINTSTS_CMOD_Pos) // 0x00000001 */ -#define GINTSTS_CMOD GINTSTS_CMOD_Msk // Current mode of operation */ +#define GINTSTS_CMOD_Msk (0x1UL << GINTSTS_CMOD_Pos) // 0x00000001 +#define GINTSTS_CMOD GINTSTS_CMOD_Msk // Current mode of operation #define GINTSTS_MMIS_Pos (1U) -#define GINTSTS_MMIS_Msk (0x1UL << GINTSTS_MMIS_Pos) // 0x00000002 */ -#define GINTSTS_MMIS GINTSTS_MMIS_Msk // Mode mismatch interrupt */ +#define GINTSTS_MMIS_Msk (0x1UL << GINTSTS_MMIS_Pos) // 0x00000002 +#define GINTSTS_MMIS GINTSTS_MMIS_Msk // Mode mismatch interrupt #define GINTSTS_OTGINT_Pos (2U) -#define GINTSTS_OTGINT_Msk (0x1UL << GINTSTS_OTGINT_Pos) // 0x00000004 */ -#define GINTSTS_OTGINT GINTSTS_OTGINT_Msk // OTG interrupt */ +#define GINTSTS_OTGINT_Msk (0x1UL << GINTSTS_OTGINT_Pos) // 0x00000004 +#define GINTSTS_OTGINT GINTSTS_OTGINT_Msk // OTG interrupt #define GINTSTS_SOF_Pos (3U) -#define GINTSTS_SOF_Msk (0x1UL << GINTSTS_SOF_Pos) // 0x00000008 */ -#define GINTSTS_SOF GINTSTS_SOF_Msk // Start of frame */ +#define GINTSTS_SOF_Msk (0x1UL << GINTSTS_SOF_Pos) // 0x00000008 +#define GINTSTS_SOF GINTSTS_SOF_Msk // Start of frame #define GINTSTS_RXFLVL_Pos (4U) -#define GINTSTS_RXFLVL_Msk (0x1UL << GINTSTS_RXFLVL_Pos) // 0x00000010 */ -#define GINTSTS_RXFLVL GINTSTS_RXFLVL_Msk // RxFIFO nonempty */ +#define GINTSTS_RXFLVL_Msk (0x1UL << GINTSTS_RXFLVL_Pos) // 0x00000010 +#define GINTSTS_RXFLVL GINTSTS_RXFLVL_Msk // RxFIFO nonempty #define GINTSTS_NPTXFE_Pos (5U) -#define GINTSTS_NPTXFE_Msk (0x1UL << GINTSTS_NPTXFE_Pos) // 0x00000020 */ -#define GINTSTS_NPTXFE GINTSTS_NPTXFE_Msk // Nonperiodic TxFIFO empty */ +#define GINTSTS_NPTXFE_Msk (0x1UL << GINTSTS_NPTXFE_Pos) // 0x00000020 +#define GINTSTS_NPTXFE GINTSTS_NPTXFE_Msk // Nonperiodic TxFIFO empty #define GINTSTS_GINAKEFF_Pos (6U) -#define GINTSTS_GINAKEFF_Msk (0x1UL << GINTSTS_GINAKEFF_Pos) // 0x00000040 */ -#define GINTSTS_GINAKEFF GINTSTS_GINAKEFF_Msk // Global IN nonperiodic NAK effective */ +#define GINTSTS_GINAKEFF_Msk (0x1UL << GINTSTS_GINAKEFF_Pos) // 0x00000040 +#define GINTSTS_GINAKEFF GINTSTS_GINAKEFF_Msk // Global IN nonperiodic NAK effective #define GINTSTS_BOUTNAKEFF_Pos (7U) -#define GINTSTS_BOUTNAKEFF_Msk (0x1UL << GINTSTS_BOUTNAKEFF_Pos) // 0x00000080 */ -#define GINTSTS_BOUTNAKEFF GINTSTS_BOUTNAKEFF_Msk // Global OUT NAK effective */ +#define GINTSTS_BOUTNAKEFF_Msk (0x1UL << GINTSTS_BOUTNAKEFF_Pos) // 0x00000080 +#define GINTSTS_BOUTNAKEFF GINTSTS_BOUTNAKEFF_Msk // Global OUT NAK effective #define GINTSTS_ESUSP_Pos (10U) -#define GINTSTS_ESUSP_Msk (0x1UL << GINTSTS_ESUSP_Pos) // 0x00000400 */ -#define GINTSTS_ESUSP GINTSTS_ESUSP_Msk // Early suspend */ +#define GINTSTS_ESUSP_Msk (0x1UL << GINTSTS_ESUSP_Pos) // 0x00000400 +#define GINTSTS_ESUSP GINTSTS_ESUSP_Msk // Early suspend #define GINTSTS_USBSUSP_Pos (11U) -#define GINTSTS_USBSUSP_Msk (0x1UL << GINTSTS_USBSUSP_Pos) // 0x00000800 */ -#define GINTSTS_USBSUSP GINTSTS_USBSUSP_Msk // USB suspend */ +#define GINTSTS_USBSUSP_Msk (0x1UL << GINTSTS_USBSUSP_Pos) // 0x00000800 +#define GINTSTS_USBSUSP GINTSTS_USBSUSP_Msk // USB suspend #define GINTSTS_USBRST_Pos (12U) -#define GINTSTS_USBRST_Msk (0x1UL << GINTSTS_USBRST_Pos) // 0x00001000 */ -#define GINTSTS_USBRST GINTSTS_USBRST_Msk // USB reset */ +#define GINTSTS_USBRST_Msk (0x1UL << GINTSTS_USBRST_Pos) // 0x00001000 +#define GINTSTS_USBRST GINTSTS_USBRST_Msk // USB reset #define GINTSTS_ENUMDNE_Pos (13U) -#define GINTSTS_ENUMDNE_Msk (0x1UL << GINTSTS_ENUMDNE_Pos) // 0x00002000 */ -#define GINTSTS_ENUMDNE GINTSTS_ENUMDNE_Msk // Enumeration done */ +#define GINTSTS_ENUMDNE_Msk (0x1UL << GINTSTS_ENUMDNE_Pos) // 0x00002000 +#define GINTSTS_ENUMDNE GINTSTS_ENUMDNE_Msk // Enumeration done #define GINTSTS_ISOODRP_Pos (14U) -#define GINTSTS_ISOODRP_Msk (0x1UL << GINTSTS_ISOODRP_Pos) // 0x00004000 */ -#define GINTSTS_ISOODRP GINTSTS_ISOODRP_Msk // Isochronous OUT packet dropped interrupt */ +#define GINTSTS_ISOODRP_Msk (0x1UL << GINTSTS_ISOODRP_Pos) // 0x00004000 +#define GINTSTS_ISOODRP GINTSTS_ISOODRP_Msk // Isochronous OUT packet dropped interrupt #define GINTSTS_EOPF_Pos (15U) -#define GINTSTS_EOPF_Msk (0x1UL << GINTSTS_EOPF_Pos) // 0x00008000 */ -#define GINTSTS_EOPF GINTSTS_EOPF_Msk // End of periodic frame interrupt */ +#define GINTSTS_EOPF_Msk (0x1UL << GINTSTS_EOPF_Pos) // 0x00008000 +#define GINTSTS_EOPF GINTSTS_EOPF_Msk // End of periodic frame interrupt #define GINTSTS_IEPINT_Pos (18U) -#define GINTSTS_IEPINT_Msk (0x1UL << GINTSTS_IEPINT_Pos) // 0x00040000 */ -#define GINTSTS_IEPINT GINTSTS_IEPINT_Msk // IN endpoint interrupt */ +#define GINTSTS_IEPINT_Msk (0x1UL << GINTSTS_IEPINT_Pos) // 0x00040000 +#define GINTSTS_IEPINT GINTSTS_IEPINT_Msk // IN endpoint interrupt #define GINTSTS_OEPINT_Pos (19U) -#define GINTSTS_OEPINT_Msk (0x1UL << GINTSTS_OEPINT_Pos) // 0x00080000 */ -#define GINTSTS_OEPINT GINTSTS_OEPINT_Msk // OUT endpoint interrupt */ +#define GINTSTS_OEPINT_Msk (0x1UL << GINTSTS_OEPINT_Pos) // 0x00080000 +#define GINTSTS_OEPINT GINTSTS_OEPINT_Msk // OUT endpoint interrupt #define GINTSTS_IISOIXFR_Pos (20U) -#define GINTSTS_IISOIXFR_Msk (0x1UL << GINTSTS_IISOIXFR_Pos) // 0x00100000 */ -#define GINTSTS_IISOIXFR GINTSTS_IISOIXFR_Msk // Incomplete isochronous IN transfer */ +#define GINTSTS_IISOIXFR_Msk (0x1UL << GINTSTS_IISOIXFR_Pos) // 0x00100000 +#define GINTSTS_IISOIXFR GINTSTS_IISOIXFR_Msk // Incomplete isochronous IN transfer #define GINTSTS_PXFR_INCOMPISOOUT_Pos (21U) -#define GINTSTS_PXFR_INCOMPISOOUT_Msk (0x1UL << GINTSTS_PXFR_INCOMPISOOUT_Pos) // 0x00200000 */ -#define GINTSTS_PXFR_INCOMPISOOUT GINTSTS_PXFR_INCOMPISOOUT_Msk // Incomplete periodic transfer */ +#define GINTSTS_PXFR_INCOMPISOOUT_Msk (0x1UL << GINTSTS_PXFR_INCOMPISOOUT_Pos) // 0x00200000 +#define GINTSTS_PXFR_INCOMPISOOUT GINTSTS_PXFR_INCOMPISOOUT_Msk // Incomplete periodic transfer #define GINTSTS_DATAFSUSP_Pos (22U) -#define GINTSTS_DATAFSUSP_Msk (0x1UL << GINTSTS_DATAFSUSP_Pos) // 0x00400000 */ -#define GINTSTS_DATAFSUSP GINTSTS_DATAFSUSP_Msk // Data fetch suspended */ +#define GINTSTS_DATAFSUSP_Msk (0x1UL << GINTSTS_DATAFSUSP_Pos) // 0x00400000 +#define GINTSTS_DATAFSUSP GINTSTS_DATAFSUSP_Msk // Data fetch suspended #define GINTSTS_RSTDET_Pos (23U) -#define GINTSTS_RSTDET_Msk (0x1UL << GINTSTS_RSTDET_Pos) // 0x00800000 */ -#define GINTSTS_RSTDET GINTSTS_RSTDET_Msk // Reset detected interrupt */ +#define GINTSTS_RSTDET_Msk (0x1UL << GINTSTS_RSTDET_Pos) // 0x00800000 +#define GINTSTS_RSTDET GINTSTS_RSTDET_Msk // Reset detected interrupt #define GINTSTS_HPRTINT_Pos (24U) -#define GINTSTS_HPRTINT_Msk (0x1UL << GINTSTS_HPRTINT_Pos) // 0x01000000 */ -#define GINTSTS_HPRTINT GINTSTS_HPRTINT_Msk // Host port interrupt */ +#define GINTSTS_HPRTINT_Msk (0x1UL << GINTSTS_HPRTINT_Pos) // 0x01000000 +#define GINTSTS_HPRTINT GINTSTS_HPRTINT_Msk // Host port interrupt #define GINTSTS_HCINT_Pos (25U) -#define GINTSTS_HCINT_Msk (0x1UL << GINTSTS_HCINT_Pos) // 0x02000000 */ -#define GINTSTS_HCINT GINTSTS_HCINT_Msk // Host channels interrupt */ +#define GINTSTS_HCINT_Msk (0x1UL << GINTSTS_HCINT_Pos) // 0x02000000 +#define GINTSTS_HCINT GINTSTS_HCINT_Msk // Host channels interrupt #define GINTSTS_PTXFE_Pos (26U) -#define GINTSTS_PTXFE_Msk (0x1UL << GINTSTS_PTXFE_Pos) // 0x04000000 */ -#define GINTSTS_PTXFE GINTSTS_PTXFE_Msk // Periodic TxFIFO empty */ +#define GINTSTS_PTXFE_Msk (0x1UL << GINTSTS_PTXFE_Pos) // 0x04000000 +#define GINTSTS_PTXFE GINTSTS_PTXFE_Msk // Periodic TxFIFO empty #define GINTSTS_LPMINT_Pos (27U) -#define GINTSTS_LPMINT_Msk (0x1UL << GINTSTS_LPMINT_Pos) // 0x08000000 */ -#define GINTSTS_LPMINT GINTSTS_LPMINT_Msk // LPM interrupt */ +#define GINTSTS_LPMINT_Msk (0x1UL << GINTSTS_LPMINT_Pos) // 0x08000000 +#define GINTSTS_LPMINT GINTSTS_LPMINT_Msk // LPM interrupt #define GINTSTS_CIDSCHG_Pos (28U) -#define GINTSTS_CIDSCHG_Msk (0x1UL << GINTSTS_CIDSCHG_Pos) // 0x10000000 */ -#define GINTSTS_CIDSCHG GINTSTS_CIDSCHG_Msk // Connector ID status change */ +#define GINTSTS_CIDSCHG_Msk (0x1UL << GINTSTS_CIDSCHG_Pos) // 0x10000000 +#define GINTSTS_CIDSCHG GINTSTS_CIDSCHG_Msk // Connector ID status change #define GINTSTS_DISCINT_Pos (29U) -#define GINTSTS_DISCINT_Msk (0x1UL << GINTSTS_DISCINT_Pos) // 0x20000000 */ -#define GINTSTS_DISCINT GINTSTS_DISCINT_Msk // Disconnect detected interrupt */ +#define GINTSTS_DISCINT_Msk (0x1UL << GINTSTS_DISCINT_Pos) // 0x20000000 +#define GINTSTS_DISCINT GINTSTS_DISCINT_Msk // Disconnect detected interrupt #define GINTSTS_SRQINT_Pos (30U) -#define GINTSTS_SRQINT_Msk (0x1UL << GINTSTS_SRQINT_Pos) // 0x40000000 */ -#define GINTSTS_SRQINT GINTSTS_SRQINT_Msk // Session request/new session detected interrupt */ +#define GINTSTS_SRQINT_Msk (0x1UL << GINTSTS_SRQINT_Pos) // 0x40000000 +#define GINTSTS_SRQINT GINTSTS_SRQINT_Msk // Session request/new session detected interrupt #define GINTSTS_WKUINT_Pos (31U) -#define GINTSTS_WKUINT_Msk (0x1UL << GINTSTS_WKUINT_Pos) // 0x80000000 */ -#define GINTSTS_WKUINT GINTSTS_WKUINT_Msk // Resume/remote wakeup detected interrupt */ +#define GINTSTS_WKUINT_Msk (0x1UL << GINTSTS_WKUINT_Pos) // 0x80000000 +#define GINTSTS_WKUINT GINTSTS_WKUINT_Msk // Resume/remote wakeup detected interrupt /******************** Bit definition for GINTMSK register ********************/ #define GINTMSK_MMISM_Pos (1U) -#define GINTMSK_MMISM_Msk (0x1UL << GINTMSK_MMISM_Pos) // 0x00000002 */ -#define GINTMSK_MMISM GINTMSK_MMISM_Msk // Mode mismatch interrupt mask */ +#define GINTMSK_MMISM_Msk (0x1UL << GINTMSK_MMISM_Pos) // 0x00000002 +#define GINTMSK_MMISM GINTMSK_MMISM_Msk // Mode mismatch interrupt mask #define GINTMSK_OTGINT_Pos (2U) -#define GINTMSK_OTGINT_Msk (0x1UL << GINTMSK_OTGINT_Pos) // 0x00000004 */ -#define GINTMSK_OTGINT GINTMSK_OTGINT_Msk // OTG interrupt mask */ +#define GINTMSK_OTGINT_Msk (0x1UL << GINTMSK_OTGINT_Pos) // 0x00000004 +#define GINTMSK_OTGINT GINTMSK_OTGINT_Msk // OTG interrupt mask #define GINTMSK_SOFM_Pos (3U) -#define GINTMSK_SOFM_Msk (0x1UL << GINTMSK_SOFM_Pos) // 0x00000008 */ -#define GINTMSK_SOFM GINTMSK_SOFM_Msk // Start of frame mask */ +#define GINTMSK_SOFM_Msk (0x1UL << GINTMSK_SOFM_Pos) // 0x00000008 +#define GINTMSK_SOFM GINTMSK_SOFM_Msk // Start of frame mask #define GINTMSK_RXFLVLM_Pos (4U) -#define GINTMSK_RXFLVLM_Msk (0x1UL << GINTMSK_RXFLVLM_Pos) // 0x00000010 */ -#define GINTMSK_RXFLVLM GINTMSK_RXFLVLM_Msk // Receive FIFO nonempty mask */ +#define GINTMSK_RXFLVLM_Msk (0x1UL << GINTMSK_RXFLVLM_Pos) // 0x00000010 +#define GINTMSK_RXFLVLM GINTMSK_RXFLVLM_Msk // Receive FIFO nonempty mask #define GINTMSK_NPTXFEM_Pos (5U) -#define GINTMSK_NPTXFEM_Msk (0x1UL << GINTMSK_NPTXFEM_Pos) // 0x00000020 */ -#define GINTMSK_NPTXFEM GINTMSK_NPTXFEM_Msk // Nonperiodic TxFIFO empty mask */ +#define GINTMSK_NPTXFEM_Msk (0x1UL << GINTMSK_NPTXFEM_Pos) // 0x00000020 +#define GINTMSK_NPTXFEM GINTMSK_NPTXFEM_Msk // Nonperiodic TxFIFO empty mask #define GINTMSK_GINAKEFFM_Pos (6U) -#define GINTMSK_GINAKEFFM_Msk (0x1UL << GINTMSK_GINAKEFFM_Pos) // 0x00000040 */ -#define GINTMSK_GINAKEFFM GINTMSK_GINAKEFFM_Msk // Global nonperiodic IN NAK effective mask */ +#define GINTMSK_GINAKEFFM_Msk (0x1UL << GINTMSK_GINAKEFFM_Pos) // 0x00000040 +#define GINTMSK_GINAKEFFM GINTMSK_GINAKEFFM_Msk // Global nonperiodic IN NAK effective mask #define GINTMSK_GONAKEFFM_Pos (7U) -#define GINTMSK_GONAKEFFM_Msk (0x1UL << GINTMSK_GONAKEFFM_Pos) // 0x00000080 */ -#define GINTMSK_GONAKEFFM GINTMSK_GONAKEFFM_Msk // Global OUT NAK effective mask */ +#define GINTMSK_GONAKEFFM_Msk (0x1UL << GINTMSK_GONAKEFFM_Pos) // 0x00000080 +#define GINTMSK_GONAKEFFM GINTMSK_GONAKEFFM_Msk // Global OUT NAK effective mask #define GINTMSK_ESUSPM_Pos (10U) -#define GINTMSK_ESUSPM_Msk (0x1UL << GINTMSK_ESUSPM_Pos) // 0x00000400 */ -#define GINTMSK_ESUSPM GINTMSK_ESUSPM_Msk // Early suspend mask */ +#define GINTMSK_ESUSPM_Msk (0x1UL << GINTMSK_ESUSPM_Pos) // 0x00000400 +#define GINTMSK_ESUSPM GINTMSK_ESUSPM_Msk // Early suspend mask #define GINTMSK_USBSUSPM_Pos (11U) -#define GINTMSK_USBSUSPM_Msk (0x1UL << GINTMSK_USBSUSPM_Pos) // 0x00000800 */ -#define GINTMSK_USBSUSPM GINTMSK_USBSUSPM_Msk // USB suspend mask */ +#define GINTMSK_USBSUSPM_Msk (0x1UL << GINTMSK_USBSUSPM_Pos) // 0x00000800 +#define GINTMSK_USBSUSPM GINTMSK_USBSUSPM_Msk // USB suspend mask #define GINTMSK_USBRST_Pos (12U) -#define GINTMSK_USBRST_Msk (0x1UL << GINTMSK_USBRST_Pos) // 0x00001000 */ -#define GINTMSK_USBRST GINTMSK_USBRST_Msk // USB reset mask */ +#define GINTMSK_USBRST_Msk (0x1UL << GINTMSK_USBRST_Pos) // 0x00001000 +#define GINTMSK_USBRST GINTMSK_USBRST_Msk // USB reset mask #define GINTMSK_ENUMDNEM_Pos (13U) -#define GINTMSK_ENUMDNEM_Msk (0x1UL << GINTMSK_ENUMDNEM_Pos) // 0x00002000 */ -#define GINTMSK_ENUMDNEM GINTMSK_ENUMDNEM_Msk // Enumeration done mask */ +#define GINTMSK_ENUMDNEM_Msk (0x1UL << GINTMSK_ENUMDNEM_Pos) // 0x00002000 +#define GINTMSK_ENUMDNEM GINTMSK_ENUMDNEM_Msk // Enumeration done mask #define GINTMSK_ISOODRPM_Pos (14U) -#define GINTMSK_ISOODRPM_Msk (0x1UL << GINTMSK_ISOODRPM_Pos) // 0x00004000 */ -#define GINTMSK_ISOODRPM GINTMSK_ISOODRPM_Msk // Isochronous OUT packet dropped interrupt mask */ +#define GINTMSK_ISOODRPM_Msk (0x1UL << GINTMSK_ISOODRPM_Pos) // 0x00004000 +#define GINTMSK_ISOODRPM GINTMSK_ISOODRPM_Msk // Isochronous OUT packet dropped interrupt mask #define GINTMSK_EOPFM_Pos (15U) -#define GINTMSK_EOPFM_Msk (0x1UL << GINTMSK_EOPFM_Pos) // 0x00008000 */ -#define GINTMSK_EOPFM GINTMSK_EOPFM_Msk // End of periodic frame interrupt mask */ +#define GINTMSK_EOPFM_Msk (0x1UL << GINTMSK_EOPFM_Pos) // 0x00008000 +#define GINTMSK_EOPFM GINTMSK_EOPFM_Msk // End of periodic frame interrupt mask #define GINTMSK_EPMISM_Pos (17U) -#define GINTMSK_EPMISM_Msk (0x1UL << GINTMSK_EPMISM_Pos) // 0x00020000 */ -#define GINTMSK_EPMISM GINTMSK_EPMISM_Msk // Endpoint mismatch interrupt mask */ +#define GINTMSK_EPMISM_Msk (0x1UL << GINTMSK_EPMISM_Pos) // 0x00020000 +#define GINTMSK_EPMISM GINTMSK_EPMISM_Msk // Endpoint mismatch interrupt mask #define GINTMSK_IEPINT_Pos (18U) -#define GINTMSK_IEPINT_Msk (0x1UL << GINTMSK_IEPINT_Pos) // 0x00040000 */ -#define GINTMSK_IEPINT GINTMSK_IEPINT_Msk // IN endpoints interrupt mask */ +#define GINTMSK_IEPINT_Msk (0x1UL << GINTMSK_IEPINT_Pos) // 0x00040000 +#define GINTMSK_IEPINT GINTMSK_IEPINT_Msk // IN endpoints interrupt mask #define GINTMSK_OEPINT_Pos (19U) -#define GINTMSK_OEPINT_Msk (0x1UL << GINTMSK_OEPINT_Pos) // 0x00080000 */ -#define GINTMSK_OEPINT GINTMSK_OEPINT_Msk // OUT endpoints interrupt mask */ +#define GINTMSK_OEPINT_Msk (0x1UL << GINTMSK_OEPINT_Pos) // 0x00080000 +#define GINTMSK_OEPINT GINTMSK_OEPINT_Msk // OUT endpoints interrupt mask #define GINTMSK_IISOIXFRM_Pos (20U) -#define GINTMSK_IISOIXFRM_Msk (0x1UL << GINTMSK_IISOIXFRM_Pos) // 0x00100000 */ -#define GINTMSK_IISOIXFRM GINTMSK_IISOIXFRM_Msk // Incomplete isochronous IN transfer mask */ +#define GINTMSK_IISOIXFRM_Msk (0x1UL << GINTMSK_IISOIXFRM_Pos) // 0x00100000 +#define GINTMSK_IISOIXFRM GINTMSK_IISOIXFRM_Msk // Incomplete isochronous IN transfer mask #define GINTMSK_PXFRM_IISOOXFRM_Pos (21U) -#define GINTMSK_PXFRM_IISOOXFRM_Msk (0x1UL << GINTMSK_PXFRM_IISOOXFRM_Pos) // 0x00200000 */ -#define GINTMSK_PXFRM_IISOOXFRM GINTMSK_PXFRM_IISOOXFRM_Msk // Incomplete periodic transfer mask */ +#define GINTMSK_PXFRM_IISOOXFRM_Msk (0x1UL << GINTMSK_PXFRM_IISOOXFRM_Pos) // 0x00200000 +#define GINTMSK_PXFRM_IISOOXFRM GINTMSK_PXFRM_IISOOXFRM_Msk // Incomplete periodic transfer mask #define GINTMSK_FSUSPM_Pos (22U) -#define GINTMSK_FSUSPM_Msk (0x1UL << GINTMSK_FSUSPM_Pos) // 0x00400000 */ -#define GINTMSK_FSUSPM GINTMSK_FSUSPM_Msk // Data fetch suspended mask */ +#define GINTMSK_FSUSPM_Msk (0x1UL << GINTMSK_FSUSPM_Pos) // 0x00400000 +#define GINTMSK_FSUSPM GINTMSK_FSUSPM_Msk // Data fetch suspended mask #define GINTMSK_RSTDEM_Pos (23U) -#define GINTMSK_RSTDEM_Msk (0x1UL << GINTMSK_RSTDEM_Pos) // 0x00800000 */ -#define GINTMSK_RSTDEM GINTMSK_RSTDEM_Msk // Reset detected interrupt mask */ +#define GINTMSK_RSTDEM_Msk (0x1UL << GINTMSK_RSTDEM_Pos) // 0x00800000 +#define GINTMSK_RSTDEM GINTMSK_RSTDEM_Msk // Reset detected interrupt mask #define GINTMSK_PRTIM_Pos (24U) -#define GINTMSK_PRTIM_Msk (0x1UL << GINTMSK_PRTIM_Pos) // 0x01000000 */ -#define GINTMSK_PRTIM GINTMSK_PRTIM_Msk // Host port interrupt mask */ +#define GINTMSK_PRTIM_Msk (0x1UL << GINTMSK_PRTIM_Pos) // 0x01000000 +#define GINTMSK_PRTIM GINTMSK_PRTIM_Msk // Host port interrupt mask #define GINTMSK_HCIM_Pos (25U) -#define GINTMSK_HCIM_Msk (0x1UL << GINTMSK_HCIM_Pos) // 0x02000000 */ -#define GINTMSK_HCIM GINTMSK_HCIM_Msk // Host channels interrupt mask */ +#define GINTMSK_HCIM_Msk (0x1UL << GINTMSK_HCIM_Pos) // 0x02000000 +#define GINTMSK_HCIM GINTMSK_HCIM_Msk // Host channels interrupt mask #define GINTMSK_PTXFEM_Pos (26U) -#define GINTMSK_PTXFEM_Msk (0x1UL << GINTMSK_PTXFEM_Pos) // 0x04000000 */ -#define GINTMSK_PTXFEM GINTMSK_PTXFEM_Msk // Periodic TxFIFO empty mask */ +#define GINTMSK_PTXFEM_Msk (0x1UL << GINTMSK_PTXFEM_Pos) // 0x04000000 +#define GINTMSK_PTXFEM GINTMSK_PTXFEM_Msk // Periodic TxFIFO empty mask #define GINTMSK_LPMINTM_Pos (27U) -#define GINTMSK_LPMINTM_Msk (0x1UL << GINTMSK_LPMINTM_Pos) // 0x08000000 */ -#define GINTMSK_LPMINTM GINTMSK_LPMINTM_Msk // LPM interrupt Mask */ +#define GINTMSK_LPMINTM_Msk (0x1UL << GINTMSK_LPMINTM_Pos) // 0x08000000 +#define GINTMSK_LPMINTM GINTMSK_LPMINTM_Msk // LPM interrupt Mask #define GINTMSK_CIDSCHGM_Pos (28U) -#define GINTMSK_CIDSCHGM_Msk (0x1UL << GINTMSK_CIDSCHGM_Pos) // 0x10000000 */ -#define GINTMSK_CIDSCHGM GINTMSK_CIDSCHGM_Msk // Connector ID status change mask */ +#define GINTMSK_CIDSCHGM_Msk (0x1UL << GINTMSK_CIDSCHGM_Pos) // 0x10000000 +#define GINTMSK_CIDSCHGM GINTMSK_CIDSCHGM_Msk // Connector ID status change mask #define GINTMSK_DISCINT_Pos (29U) -#define GINTMSK_DISCINT_Msk (0x1UL << GINTMSK_DISCINT_Pos) // 0x20000000 */ -#define GINTMSK_DISCINT GINTMSK_DISCINT_Msk // Disconnect detected interrupt mask */ +#define GINTMSK_DISCINT_Msk (0x1UL << GINTMSK_DISCINT_Pos) // 0x20000000 +#define GINTMSK_DISCINT GINTMSK_DISCINT_Msk // Disconnect detected interrupt mask #define GINTMSK_SRQIM_Pos (30U) -#define GINTMSK_SRQIM_Msk (0x1UL << GINTMSK_SRQIM_Pos) // 0x40000000 */ -#define GINTMSK_SRQIM GINTMSK_SRQIM_Msk // Session request/new session detected interrupt mask */ +#define GINTMSK_SRQIM_Msk (0x1UL << GINTMSK_SRQIM_Pos) // 0x40000000 +#define GINTMSK_SRQIM GINTMSK_SRQIM_Msk // Session request/new session detected interrupt mask #define GINTMSK_WUIM_Pos (31U) -#define GINTMSK_WUIM_Msk (0x1UL << GINTMSK_WUIM_Pos) // 0x80000000 */ -#define GINTMSK_WUIM GINTMSK_WUIM_Msk // Resume/remote wakeup detected interrupt mask */ +#define GINTMSK_WUIM_Msk (0x1UL << GINTMSK_WUIM_Pos) // 0x80000000 +#define GINTMSK_WUIM GINTMSK_WUIM_Msk // Resume/remote wakeup detected interrupt mask /******************** Bit definition for DAINT register ********************/ #define DAINT_IEPINT_Pos (0U) -#define DAINT_IEPINT_Msk (0xFFFFUL << DAINT_IEPINT_Pos) // 0x0000FFFF */ -#define DAINT_IEPINT DAINT_IEPINT_Msk // IN endpoint interrupt bits */ +#define DAINT_IEPINT_Msk (0xFFFFUL << DAINT_IEPINT_Pos) // 0x0000FFFF +#define DAINT_IEPINT DAINT_IEPINT_Msk // IN endpoint interrupt bits #define DAINT_OEPINT_Pos (16U) -#define DAINT_OEPINT_Msk (0xFFFFUL << DAINT_OEPINT_Pos) // 0xFFFF0000 */ -#define DAINT_OEPINT DAINT_OEPINT_Msk // OUT endpoint interrupt bits */ +#define DAINT_OEPINT_Msk (0xFFFFUL << DAINT_OEPINT_Pos) // 0xFFFF0000 +#define DAINT_OEPINT DAINT_OEPINT_Msk // OUT endpoint interrupt bits /******************** Bit definition for HAINTMSK register ********************/ #define HAINTMSK_HAINTM_Pos (0U) -#define HAINTMSK_HAINTM_Msk (0xFFFFUL << HAINTMSK_HAINTM_Pos) // 0x0000FFFF */ -#define HAINTMSK_HAINTM HAINTMSK_HAINTM_Msk // Channel interrupt mask */ +#define HAINTMSK_HAINTM_Msk (0xFFFFUL << HAINTMSK_HAINTM_Pos) // 0x0000FFFF +#define HAINTMSK_HAINTM HAINTMSK_HAINTM_Msk // Channel interrupt mask /******************** Bit definition for GRXSTSP register ********************/ #define GRXSTSP_EPNUM_Pos (0U) -#define GRXSTSP_EPNUM_Msk (0xFUL << GRXSTSP_EPNUM_Pos) // 0x0000000F */ -#define GRXSTSP_EPNUM GRXSTSP_EPNUM_Msk // IN EP interrupt mask bits */ +#define GRXSTSP_EPNUM_Msk (0xFUL << GRXSTSP_EPNUM_Pos) // 0x0000000F +#define GRXSTSP_EPNUM GRXSTSP_EPNUM_Msk // IN EP interrupt mask bits #define GRXSTSP_BCNT_Pos (4U) -#define GRXSTSP_BCNT_Msk (0x7FFUL << GRXSTSP_BCNT_Pos) // 0x00007FF0 */ -#define GRXSTSP_BCNT GRXSTSP_BCNT_Msk // OUT EP interrupt mask bits */ +#define GRXSTSP_BCNT_Msk (0x7FFUL << GRXSTSP_BCNT_Pos) // 0x00007FF0 +#define GRXSTSP_BCNT GRXSTSP_BCNT_Msk // OUT EP interrupt mask bits #define GRXSTSP_DPID_Pos (15U) -#define GRXSTSP_DPID_Msk (0x3UL << GRXSTSP_DPID_Pos) // 0x00018000 */ -#define GRXSTSP_DPID GRXSTSP_DPID_Msk // OUT EP interrupt mask bits */ +#define GRXSTSP_DPID_Msk (0x3UL << GRXSTSP_DPID_Pos) // 0x00018000 +#define GRXSTSP_DPID GRXSTSP_DPID_Msk // OUT EP interrupt mask bits #define GRXSTSP_PKTSTS_Pos (17U) -#define GRXSTSP_PKTSTS_Msk (0xFUL << GRXSTSP_PKTSTS_Pos) // 0x001E0000 */ -#define GRXSTSP_PKTSTS GRXSTSP_PKTSTS_Msk // OUT EP interrupt mask bits */ +#define GRXSTSP_PKTSTS_Msk (0xFUL << GRXSTSP_PKTSTS_Pos) // 0x001E0000 +#define GRXSTSP_PKTSTS GRXSTSP_PKTSTS_Msk // OUT EP interrupt mask bits #define GRXSTS_PKTSTS_GLOBALOUTNAK 1 #define GRXSTS_PKTSTS_OUTRX 2 @@ -934,773 +934,803 @@ TU_VERIFY_STATIC(offsetof(dwc2_regs_t, fifo ) == 0x1000, "incorrect size"); /******************** Bit definition for DAINTMSK register ********************/ #define DAINTMSK_IEPM_Pos (0U) -#define DAINTMSK_IEPM_Msk (0xFFFFUL << DAINTMSK_IEPM_Pos) // 0x0000FFFF */ -#define DAINTMSK_IEPM DAINTMSK_IEPM_Msk // IN EP interrupt mask bits */ +#define DAINTMSK_IEPM_Msk (0xFFFFUL << DAINTMSK_IEPM_Pos) // 0x0000FFFF +#define DAINTMSK_IEPM DAINTMSK_IEPM_Msk // IN EP interrupt mask bits #define DAINTMSK_OEPM_Pos (16U) -#define DAINTMSK_OEPM_Msk (0xFFFFUL << DAINTMSK_OEPM_Pos) // 0xFFFF0000 */ -#define DAINTMSK_OEPM DAINTMSK_OEPM_Msk // OUT EP interrupt mask bits */ +#define DAINTMSK_OEPM_Msk (0xFFFFUL << DAINTMSK_OEPM_Pos) // 0xFFFF0000 +#define DAINTMSK_OEPM DAINTMSK_OEPM_Msk // OUT EP interrupt mask bits #if 0 /******************** Bit definition for OTG register ********************/ #define CHNUM_Pos (0U) -#define CHNUM_Msk (0xFUL << CHNUM_Pos) // 0x0000000F */ -#define CHNUM CHNUM_Msk // Channel number */ -#define CHNUM_0 (0x1UL << CHNUM_Pos) // 0x00000001 */ -#define CHNUM_1 (0x2UL << CHNUM_Pos) // 0x00000002 */ -#define CHNUM_2 (0x4UL << CHNUM_Pos) // 0x00000004 */ -#define CHNUM_3 (0x8UL << CHNUM_Pos) // 0x00000008 */ +#define CHNUM_Msk (0xFUL << CHNUM_Pos) // 0x0000000F +#define CHNUM CHNUM_Msk // Channel number +#define CHNUM_0 (0x1UL << CHNUM_Pos) // 0x00000001 +#define CHNUM_1 (0x2UL << CHNUM_Pos) // 0x00000002 +#define CHNUM_2 (0x4UL << CHNUM_Pos) // 0x00000004 +#define CHNUM_3 (0x8UL << CHNUM_Pos) // 0x00000008 #define BCNT_Pos (4U) -#define BCNT_Msk (0x7FFUL << BCNT_Pos) // 0x00007FF0 */ -#define BCNT BCNT_Msk // Byte count */ +#define BCNT_Msk (0x7FFUL << BCNT_Pos) // 0x00007FF0 +#define BCNT BCNT_Msk // Byte count #define DPID_Pos (15U) -#define DPID_Msk (0x3UL << DPID_Pos) // 0x00018000 */ -#define DPID DPID_Msk // Data PID */ -#define DPID_0 (0x1UL << DPID_Pos) // 0x00008000 */ -#define DPID_1 (0x2UL << DPID_Pos) // 0x00010000 */ +#define DPID_Msk (0x3UL << DPID_Pos) // 0x00018000 +#define DPID DPID_Msk // Data PID +#define DPID_0 (0x1UL << DPID_Pos) // 0x00008000 +#define DPID_1 (0x2UL << DPID_Pos) // 0x00010000 #define PKTSTS_Pos (17U) -#define PKTSTS_Msk (0xFUL << PKTSTS_Pos) // 0x001E0000 */ -#define PKTSTS PKTSTS_Msk // Packet status */ -#define PKTSTS_0 (0x1UL << PKTSTS_Pos) // 0x00020000 */ -#define PKTSTS_1 (0x2UL << PKTSTS_Pos) // 0x00040000 */ -#define PKTSTS_2 (0x4UL << PKTSTS_Pos) // 0x00080000 */ -#define PKTSTS_3 (0x8UL << PKTSTS_Pos) // 0x00100000 */ +#define PKTSTS_Msk (0xFUL << PKTSTS_Pos) // 0x001E0000 +#define PKTSTS PKTSTS_Msk // Packet status +#define PKTSTS_0 (0x1UL << PKTSTS_Pos) // 0x00020000 +#define PKTSTS_1 (0x2UL << PKTSTS_Pos) // 0x00040000 +#define PKTSTS_2 (0x4UL << PKTSTS_Pos) // 0x00080000 +#define PKTSTS_3 (0x8UL << PKTSTS_Pos) // 0x00100000 #define EPNUM_Pos (0U) -#define EPNUM_Msk (0xFUL << EPNUM_Pos) // 0x0000000F */ -#define EPNUM EPNUM_Msk // Endpoint number */ -#define EPNUM_0 (0x1UL << EPNUM_Pos) // 0x00000001 */ -#define EPNUM_1 (0x2UL << EPNUM_Pos) // 0x00000002 */ -#define EPNUM_2 (0x4UL << EPNUM_Pos) // 0x00000004 */ -#define EPNUM_3 (0x8UL << EPNUM_Pos) // 0x00000008 */ +#define EPNUM_Msk (0xFUL << EPNUM_Pos) // 0x0000000F +#define EPNUM EPNUM_Msk // Endpoint number +#define EPNUM_0 (0x1UL << EPNUM_Pos) // 0x00000001 +#define EPNUM_1 (0x2UL << EPNUM_Pos) // 0x00000002 +#define EPNUM_2 (0x4UL << EPNUM_Pos) // 0x00000004 +#define EPNUM_3 (0x8UL << EPNUM_Pos) // 0x00000008 #define FRMNUM_Pos (21U) -#define FRMNUM_Msk (0xFUL << FRMNUM_Pos) // 0x01E00000 */ -#define FRMNUM FRMNUM_Msk // Frame number */ -#define FRMNUM_0 (0x1UL << FRMNUM_Pos) // 0x00200000 */ -#define FRMNUM_1 (0x2UL << FRMNUM_Pos) // 0x00400000 */ -#define FRMNUM_2 (0x4UL << FRMNUM_Pos) // 0x00800000 */ -#define FRMNUM_3 (0x8UL << FRMNUM_Pos) // 0x01000000 */ +#define FRMNUM_Msk (0xFUL << FRMNUM_Pos) // 0x01E00000 +#define FRMNUM FRMNUM_Msk // Frame number +#define FRMNUM_0 (0x1UL << FRMNUM_Pos) // 0x00200000 +#define FRMNUM_1 (0x2UL << FRMNUM_Pos) // 0x00400000 +#define FRMNUM_2 (0x4UL << FRMNUM_Pos) // 0x00800000 +#define FRMNUM_3 (0x8UL << FRMNUM_Pos) // 0x01000000 #endif /******************** Bit definition for GRXFSIZ register ********************/ #define GRXFSIZ_RXFD_Pos (0U) -#define GRXFSIZ_RXFD_Msk (0xFFFFUL << GRXFSIZ_RXFD_Pos) // 0x0000FFFF */ -#define GRXFSIZ_RXFD GRXFSIZ_RXFD_Msk // RxFIFO depth */ +#define GRXFSIZ_RXFD_Msk (0xFFFFUL << GRXFSIZ_RXFD_Pos) // 0x0000FFFF +#define GRXFSIZ_RXFD GRXFSIZ_RXFD_Msk // RxFIFO depth /******************** Bit definition for DVBUSDIS register ********************/ #define DVBUSDIS_VBUSDT_Pos (0U) -#define DVBUSDIS_VBUSDT_Msk (0xFFFFUL << DVBUSDIS_VBUSDT_Pos) // 0x0000FFFF */ -#define DVBUSDIS_VBUSDT DVBUSDIS_VBUSDT_Msk // Device VBUS discharge time */ +#define DVBUSDIS_VBUSDT_Msk (0xFFFFUL << DVBUSDIS_VBUSDT_Pos) // 0x0000FFFF +#define DVBUSDIS_VBUSDT DVBUSDIS_VBUSDT_Msk // Device VBUS discharge time /******************** Bit definition for OTG register ********************/ #define GNPTXFSIZ_NPTXFSA_Pos (0U) -#define GNPTXFSIZ_NPTXFSA_Msk (0xFFFFUL << GNPTXFSIZ_NPTXFSA_Pos) // 0x0000FFFF */ -#define GNPTXFSIZ_NPTXFSA GNPTXFSIZ_NPTXFSA_Msk // Nonperiodic transmit RAM start address */ +#define GNPTXFSIZ_NPTXFSA_Msk (0xFFFFUL << GNPTXFSIZ_NPTXFSA_Pos) // 0x0000FFFF +#define GNPTXFSIZ_NPTXFSA GNPTXFSIZ_NPTXFSA_Msk // Nonperiodic transmit RAM start address #define GNPTXFSIZ_NPTXFD_Pos (16U) -#define GNPTXFSIZ_NPTXFD_Msk (0xFFFFUL << GNPTXFSIZ_NPTXFD_Pos) // 0xFFFF0000 */ -#define GNPTXFSIZ_NPTXFD GNPTXFSIZ_NPTXFD_Msk // Nonperiodic TxFIFO depth */ +#define GNPTXFSIZ_NPTXFD_Msk (0xFFFFUL << GNPTXFSIZ_NPTXFD_Pos) // 0xFFFF0000 +#define GNPTXFSIZ_NPTXFD GNPTXFSIZ_NPTXFD_Msk // Nonperiodic TxFIFO depth #define DIEPTXF0_TX0FSA_Pos (0U) -#define DIEPTXF0_TX0FSA_Msk (0xFFFFUL << DIEPTXF0_TX0FSA_Pos) // 0x0000FFFF */ -#define DIEPTXF0_TX0FSA DIEPTXF0_TX0FSA_Msk // Endpoint 0 transmit RAM start address */ +#define DIEPTXF0_TX0FSA_Msk (0xFFFFUL << DIEPTXF0_TX0FSA_Pos) // 0x0000FFFF +#define DIEPTXF0_TX0FSA DIEPTXF0_TX0FSA_Msk // Endpoint 0 transmit RAM start address #define DIEPTXF0_TX0FD_Pos (16U) -#define DIEPTXF0_TX0FD_Msk (0xFFFFUL << DIEPTXF0_TX0FD_Pos) // 0xFFFF0000 */ -#define DIEPTXF0_TX0FD DIEPTXF0_TX0FD_Msk // Endpoint 0 TxFIFO depth */ +#define DIEPTXF0_TX0FD_Msk (0xFFFFUL << DIEPTXF0_TX0FD_Pos) // 0xFFFF0000 +#define DIEPTXF0_TX0FD DIEPTXF0_TX0FD_Msk // Endpoint 0 TxFIFO depth /******************** Bit definition for DVBUSPULSE register ********************/ #define DVBUSPULSE_DVBUSP_Pos (0U) -#define DVBUSPULSE_DVBUSP_Msk (0xFFFUL << DVBUSPULSE_DVBUSP_Pos) // 0x00000FFF */ -#define DVBUSPULSE_DVBUSP DVBUSPULSE_DVBUSP_Msk // Device VBUS pulsing time */ +#define DVBUSPULSE_DVBUSP_Msk (0xFFFUL << DVBUSPULSE_DVBUSP_Pos) // 0x00000FFF +#define DVBUSPULSE_DVBUSP DVBUSPULSE_DVBUSP_Msk // Device VBUS pulsing time /******************** Bit definition for GNPTXSTS register ********************/ #define GNPTXSTS_NPTXFSAV_Pos (0U) -#define GNPTXSTS_NPTXFSAV_Msk (0xFFFFUL << GNPTXSTS_NPTXFSAV_Pos) // 0x0000FFFF */ -#define GNPTXSTS_NPTXFSAV GNPTXSTS_NPTXFSAV_Msk // Nonperiodic TxFIFO space available */ +#define GNPTXSTS_NPTXFSAV_Msk (0xFFFFUL << GNPTXSTS_NPTXFSAV_Pos) // 0x0000FFFF +#define GNPTXSTS_NPTXFSAV GNPTXSTS_NPTXFSAV_Msk // Nonperiodic TxFIFO space available #define GNPTXSTS_NPTQXSAV_Pos (16U) -#define GNPTXSTS_NPTQXSAV_Msk (0xFFUL << GNPTXSTS_NPTQXSAV_Pos) // 0x00FF0000 */ -#define GNPTXSTS_NPTQXSAV GNPTXSTS_NPTQXSAV_Msk // Nonperiodic transmit request queue space available */ -#define GNPTXSTS_NPTQXSAV_0 (0x01UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00010000 */ -#define GNPTXSTS_NPTQXSAV_1 (0x02UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00020000 */ -#define GNPTXSTS_NPTQXSAV_2 (0x04UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00040000 */ -#define GNPTXSTS_NPTQXSAV_3 (0x08UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00080000 */ -#define GNPTXSTS_NPTQXSAV_4 (0x10UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00100000 */ -#define GNPTXSTS_NPTQXSAV_5 (0x20UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00200000 */ -#define GNPTXSTS_NPTQXSAV_6 (0x40UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00400000 */ -#define GNPTXSTS_NPTQXSAV_7 (0x80UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00800000 */ +#define GNPTXSTS_NPTQXSAV_Msk (0xFFUL << GNPTXSTS_NPTQXSAV_Pos) // 0x00FF0000 +#define GNPTXSTS_NPTQXSAV GNPTXSTS_NPTQXSAV_Msk // Nonperiodic transmit request queue space available +#define GNPTXSTS_NPTQXSAV_0 (0x01UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00010000 +#define GNPTXSTS_NPTQXSAV_1 (0x02UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00020000 +#define GNPTXSTS_NPTQXSAV_2 (0x04UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00040000 +#define GNPTXSTS_NPTQXSAV_3 (0x08UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00080000 +#define GNPTXSTS_NPTQXSAV_4 (0x10UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00100000 +#define GNPTXSTS_NPTQXSAV_5 (0x20UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00200000 +#define GNPTXSTS_NPTQXSAV_6 (0x40UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00400000 +#define GNPTXSTS_NPTQXSAV_7 (0x80UL << GNPTXSTS_NPTQXSAV_Pos) // 0x00800000 #define GNPTXSTS_NPTXQTOP_Pos (24U) -#define GNPTXSTS_NPTXQTOP_Msk (0x7FUL << GNPTXSTS_NPTXQTOP_Pos) // 0x7F000000 */ -#define GNPTXSTS_NPTXQTOP GNPTXSTS_NPTXQTOP_Msk // Top of the nonperiodic transmit request queue */ -#define GNPTXSTS_NPTXQTOP_0 (0x01UL << GNPTXSTS_NPTXQTOP_Pos) // 0x01000000 */ -#define GNPTXSTS_NPTXQTOP_1 (0x02UL << GNPTXSTS_NPTXQTOP_Pos) // 0x02000000 */ -#define GNPTXSTS_NPTXQTOP_2 (0x04UL << GNPTXSTS_NPTXQTOP_Pos) // 0x04000000 */ -#define GNPTXSTS_NPTXQTOP_3 (0x08UL << GNPTXSTS_NPTXQTOP_Pos) // 0x08000000 */ -#define GNPTXSTS_NPTXQTOP_4 (0x10UL << GNPTXSTS_NPTXQTOP_Pos) // 0x10000000 */ -#define GNPTXSTS_NPTXQTOP_5 (0x20UL << GNPTXSTS_NPTXQTOP_Pos) // 0x20000000 */ -#define GNPTXSTS_NPTXQTOP_6 (0x40UL << GNPTXSTS_NPTXQTOP_Pos) // 0x40000000 */ +#define GNPTXSTS_NPTXQTOP_Msk (0x7FUL << GNPTXSTS_NPTXQTOP_Pos) // 0x7F000000 +#define GNPTXSTS_NPTXQTOP GNPTXSTS_NPTXQTOP_Msk // Top of the nonperiodic transmit request queue +#define GNPTXSTS_NPTXQTOP_0 (0x01UL << GNPTXSTS_NPTXQTOP_Pos) // 0x01000000 +#define GNPTXSTS_NPTXQTOP_1 (0x02UL << GNPTXSTS_NPTXQTOP_Pos) // 0x02000000 +#define GNPTXSTS_NPTXQTOP_2 (0x04UL << GNPTXSTS_NPTXQTOP_Pos) // 0x04000000 +#define GNPTXSTS_NPTXQTOP_3 (0x08UL << GNPTXSTS_NPTXQTOP_Pos) // 0x08000000 +#define GNPTXSTS_NPTXQTOP_4 (0x10UL << GNPTXSTS_NPTXQTOP_Pos) // 0x10000000 +#define GNPTXSTS_NPTXQTOP_5 (0x20UL << GNPTXSTS_NPTXQTOP_Pos) // 0x20000000 +#define GNPTXSTS_NPTXQTOP_6 (0x40UL << GNPTXSTS_NPTXQTOP_Pos) // 0x40000000 /******************** Bit definition for DTHRCTL register ********************/ #define DTHRCTL_NONISOTHREN_Pos (0U) -#define DTHRCTL_NONISOTHREN_Msk (0x1UL << DTHRCTL_NONISOTHREN_Pos) // 0x00000001 */ -#define DTHRCTL_NONISOTHREN DTHRCTL_NONISOTHREN_Msk // Nonisochronous IN endpoints threshold enable */ +#define DTHRCTL_NONISOTHREN_Msk (0x1UL << DTHRCTL_NONISOTHREN_Pos) // 0x00000001 +#define DTHRCTL_NONISOTHREN DTHRCTL_NONISOTHREN_Msk // Nonisochronous IN endpoints threshold enable #define DTHRCTL_ISOTHREN_Pos (1U) -#define DTHRCTL_ISOTHREN_Msk (0x1UL << DTHRCTL_ISOTHREN_Pos) // 0x00000002 */ -#define DTHRCTL_ISOTHREN DTHRCTL_ISOTHREN_Msk // ISO IN endpoint threshold enable */ +#define DTHRCTL_ISOTHREN_Msk (0x1UL << DTHRCTL_ISOTHREN_Pos) // 0x00000002 +#define DTHRCTL_ISOTHREN DTHRCTL_ISOTHREN_Msk // ISO IN endpoint threshold enable #define DTHRCTL_TXTHRLEN_Pos (2U) -#define DTHRCTL_TXTHRLEN_Msk (0x1FFUL << DTHRCTL_TXTHRLEN_Pos) // 0x000007FC */ -#define DTHRCTL_TXTHRLEN DTHRCTL_TXTHRLEN_Msk // Transmit threshold length */ -#define DTHRCTL_TXTHRLEN_0 (0x001UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000004 */ -#define DTHRCTL_TXTHRLEN_1 (0x002UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000008 */ -#define DTHRCTL_TXTHRLEN_2 (0x004UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000010 */ -#define DTHRCTL_TXTHRLEN_3 (0x008UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000020 */ -#define DTHRCTL_TXTHRLEN_4 (0x010UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000040 */ -#define DTHRCTL_TXTHRLEN_5 (0x020UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000080 */ -#define DTHRCTL_TXTHRLEN_6 (0x040UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000100 */ -#define DTHRCTL_TXTHRLEN_7 (0x080UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000200 */ -#define DTHRCTL_TXTHRLEN_8 (0x100UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000400 */ +#define DTHRCTL_TXTHRLEN_Msk (0x1FFUL << DTHRCTL_TXTHRLEN_Pos) // 0x000007FC +#define DTHRCTL_TXTHRLEN DTHRCTL_TXTHRLEN_Msk // Transmit threshold length +#define DTHRCTL_TXTHRLEN_0 (0x001UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000004 +#define DTHRCTL_TXTHRLEN_1 (0x002UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000008 +#define DTHRCTL_TXTHRLEN_2 (0x004UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000010 +#define DTHRCTL_TXTHRLEN_3 (0x008UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000020 +#define DTHRCTL_TXTHRLEN_4 (0x010UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000040 +#define DTHRCTL_TXTHRLEN_5 (0x020UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000080 +#define DTHRCTL_TXTHRLEN_6 (0x040UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000100 +#define DTHRCTL_TXTHRLEN_7 (0x080UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000200 +#define DTHRCTL_TXTHRLEN_8 (0x100UL << DTHRCTL_TXTHRLEN_Pos) // 0x00000400 #define DTHRCTL_RXTHREN_Pos (16U) -#define DTHRCTL_RXTHREN_Msk (0x1UL << DTHRCTL_RXTHREN_Pos) // 0x00010000 */ -#define DTHRCTL_RXTHREN DTHRCTL_RXTHREN_Msk // Receive threshold enable */ +#define DTHRCTL_RXTHREN_Msk (0x1UL << DTHRCTL_RXTHREN_Pos) // 0x00010000 +#define DTHRCTL_RXTHREN DTHRCTL_RXTHREN_Msk // Receive threshold enable #define DTHRCTL_RXTHRLEN_Pos (17U) -#define DTHRCTL_RXTHRLEN_Msk (0x1FFUL << DTHRCTL_RXTHRLEN_Pos) // 0x03FE0000 */ -#define DTHRCTL_RXTHRLEN DTHRCTL_RXTHRLEN_Msk // Receive threshold length */ -#define DTHRCTL_RXTHRLEN_0 (0x001UL << DTHRCTL_RXTHRLEN_Pos) // 0x00020000 */ -#define DTHRCTL_RXTHRLEN_1 (0x002UL << DTHRCTL_RXTHRLEN_Pos) // 0x00040000 */ -#define DTHRCTL_RXTHRLEN_2 (0x004UL << DTHRCTL_RXTHRLEN_Pos) // 0x00080000 */ -#define DTHRCTL_RXTHRLEN_3 (0x008UL << DTHRCTL_RXTHRLEN_Pos) // 0x00100000 */ -#define DTHRCTL_RXTHRLEN_4 (0x010UL << DTHRCTL_RXTHRLEN_Pos) // 0x00200000 */ -#define DTHRCTL_RXTHRLEN_5 (0x020UL << DTHRCTL_RXTHRLEN_Pos) // 0x00400000 */ -#define DTHRCTL_RXTHRLEN_6 (0x040UL << DTHRCTL_RXTHRLEN_Pos) // 0x00800000 */ -#define DTHRCTL_RXTHRLEN_7 (0x080UL << DTHRCTL_RXTHRLEN_Pos) // 0x01000000 */ -#define DTHRCTL_RXTHRLEN_8 (0x100UL << DTHRCTL_RXTHRLEN_Pos) // 0x02000000 */ +#define DTHRCTL_RXTHRLEN_Msk (0x1FFUL << DTHRCTL_RXTHRLEN_Pos) // 0x03FE0000 +#define DTHRCTL_RXTHRLEN DTHRCTL_RXTHRLEN_Msk // Receive threshold length +#define DTHRCTL_RXTHRLEN_0 (0x001UL << DTHRCTL_RXTHRLEN_Pos) // 0x00020000 +#define DTHRCTL_RXTHRLEN_1 (0x002UL << DTHRCTL_RXTHRLEN_Pos) // 0x00040000 +#define DTHRCTL_RXTHRLEN_2 (0x004UL << DTHRCTL_RXTHRLEN_Pos) // 0x00080000 +#define DTHRCTL_RXTHRLEN_3 (0x008UL << DTHRCTL_RXTHRLEN_Pos) // 0x00100000 +#define DTHRCTL_RXTHRLEN_4 (0x010UL << DTHRCTL_RXTHRLEN_Pos) // 0x00200000 +#define DTHRCTL_RXTHRLEN_5 (0x020UL << DTHRCTL_RXTHRLEN_Pos) // 0x00400000 +#define DTHRCTL_RXTHRLEN_6 (0x040UL << DTHRCTL_RXTHRLEN_Pos) // 0x00800000 +#define DTHRCTL_RXTHRLEN_7 (0x080UL << DTHRCTL_RXTHRLEN_Pos) // 0x01000000 +#define DTHRCTL_RXTHRLEN_8 (0x100UL << DTHRCTL_RXTHRLEN_Pos) // 0x02000000 #define DTHRCTL_ARPEN_Pos (27U) -#define DTHRCTL_ARPEN_Msk (0x1UL << DTHRCTL_ARPEN_Pos) // 0x08000000 */ -#define DTHRCTL_ARPEN DTHRCTL_ARPEN_Msk // Arbiter parking enable */ +#define DTHRCTL_ARPEN_Msk (0x1UL << DTHRCTL_ARPEN_Pos) // 0x08000000 +#define DTHRCTL_ARPEN DTHRCTL_ARPEN_Msk // Arbiter parking enable /******************** Bit definition for DIEPEMPMSK register ********************/ #define DIEPEMPMSK_INEPTXFEM_Pos (0U) -#define DIEPEMPMSK_INEPTXFEM_Msk (0xFFFFUL << DIEPEMPMSK_INEPTXFEM_Pos) // 0x0000FFFF */ -#define DIEPEMPMSK_INEPTXFEM DIEPEMPMSK_INEPTXFEM_Msk // IN EP Tx FIFO empty interrupt mask bits */ +#define DIEPEMPMSK_INEPTXFEM_Msk (0xFFFFUL << DIEPEMPMSK_INEPTXFEM_Pos) // 0x0000FFFF +#define DIEPEMPMSK_INEPTXFEM DIEPEMPMSK_INEPTXFEM_Msk // IN EP Tx FIFO empty interrupt mask bits /******************** Bit definition for DEACHINT register ********************/ #define DEACHINT_IEP1INT_Pos (1U) -#define DEACHINT_IEP1INT_Msk (0x1UL << DEACHINT_IEP1INT_Pos) // 0x00000002 */ -#define DEACHINT_IEP1INT DEACHINT_IEP1INT_Msk // IN endpoint 1interrupt bit */ +#define DEACHINT_IEP1INT_Msk (0x1UL << DEACHINT_IEP1INT_Pos) // 0x00000002 +#define DEACHINT_IEP1INT DEACHINT_IEP1INT_Msk // IN endpoint 1interrupt bit #define DEACHINT_OEP1INT_Pos (17U) -#define DEACHINT_OEP1INT_Msk (0x1UL << DEACHINT_OEP1INT_Pos) // 0x00020000 */ -#define DEACHINT_OEP1INT DEACHINT_OEP1INT_Msk // OUT endpoint 1 interrupt bit */ +#define DEACHINT_OEP1INT_Msk (0x1UL << DEACHINT_OEP1INT_Pos) // 0x00020000 +#define DEACHINT_OEP1INT DEACHINT_OEP1INT_Msk // OUT endpoint 1 interrupt bit /******************** Bit definition for GCCFG register ********************/ #define STM32_GCCFG_DCDET_Pos (0U) -#define STM32_GCCFG_DCDET_Msk (0x1UL << STM32_GCCFG_DCDET_Pos) // 0x00000001 */ -#define STM32_GCCFG_DCDET STM32_GCCFG_DCDET_Msk // Data contact detection (DCD) status */ +#define STM32_GCCFG_DCDET_Msk (0x1UL << STM32_GCCFG_DCDET_Pos) // 0x00000001 +#define STM32_GCCFG_DCDET STM32_GCCFG_DCDET_Msk // Data contact detection (DCD) status + #define STM32_GCCFG_PDET_Pos (1U) -#define STM32_GCCFG_PDET_Msk (0x1UL << STM32_GCCFG_PDET_Pos) // 0x00000002 */ -#define STM32_GCCFG_PDET STM32_GCCFG_PDET_Msk // Primary detection (PD) status */ +#define STM32_GCCFG_PDET_Msk (0x1UL << STM32_GCCFG_PDET_Pos) // 0x00000002 +#define STM32_GCCFG_PDET STM32_GCCFG_PDET_Msk // Primary detection (PD) status + #define STM32_GCCFG_SDET_Pos (2U) -#define STM32_GCCFG_SDET_Msk (0x1UL << STM32_GCCFG_SDET_Pos) // 0x00000004 */ -#define STM32_GCCFG_SDET STM32_GCCFG_SDET_Msk // Secondary detection (SD) status */ +#define STM32_GCCFG_SDET_Msk (0x1UL << STM32_GCCFG_SDET_Pos) // 0x00000004 +#define STM32_GCCFG_SDET STM32_GCCFG_SDET_Msk // Secondary detection (SD) status + #define STM32_GCCFG_PS2DET_Pos (3U) -#define STM32_GCCFG_PS2DET_Msk (0x1UL << STM32_GCCFG_PS2DET_Pos) // 0x00000008 */ -#define STM32_GCCFG_PS2DET STM32_GCCFG_PS2DET_Msk // DM pull-up detection status */ +#define STM32_GCCFG_PS2DET_Msk (0x1UL << STM32_GCCFG_PS2DET_Pos) // 0x00000008 +#define STM32_GCCFG_PS2DET STM32_GCCFG_PS2DET_Msk // DM pull-up detection status + #define STM32_GCCFG_PWRDWN_Pos (16U) -#define STM32_GCCFG_PWRDWN_Msk (0x1UL << STM32_GCCFG_PWRDWN_Pos) // 0x00010000 */ -#define STM32_GCCFG_PWRDWN STM32_GCCFG_PWRDWN_Msk // Power down */ +#define STM32_GCCFG_PWRDWN_Msk (0x1UL << STM32_GCCFG_PWRDWN_Pos) // 0x00010000 +#define STM32_GCCFG_PWRDWN STM32_GCCFG_PWRDWN_Msk // Power down + #define STM32_GCCFG_BCDEN_Pos (17U) -#define STM32_GCCFG_BCDEN_Msk (0x1UL << STM32_GCCFG_BCDEN_Pos) // 0x00020000 */ -#define STM32_GCCFG_BCDEN STM32_GCCFG_BCDEN_Msk // Battery charging detector (BCD) enable */ +#define STM32_GCCFG_BCDEN_Msk (0x1UL << STM32_GCCFG_BCDEN_Pos) // 0x00020000 +#define STM32_GCCFG_BCDEN STM32_GCCFG_BCDEN_Msk // Battery charging detector (BCD) enable + #define STM32_GCCFG_DCDEN_Pos (18U) -#define STM32_GCCFG_DCDEN_Msk (0x1UL << STM32_GCCFG_DCDEN_Pos) // 0x00040000 */ +#define STM32_GCCFG_DCDEN_Msk (0x1UL << STM32_GCCFG_DCDEN_Pos) // 0x00040000 #define STM32_GCCFG_DCDEN STM32_GCCFG_DCDEN_Msk // Data contact detection (DCD) mode enable*/ + #define STM32_GCCFG_PDEN_Pos (19U) -#define STM32_GCCFG_PDEN_Msk (0x1UL << STM32_GCCFG_PDEN_Pos) // 0x00080000 */ +#define STM32_GCCFG_PDEN_Msk (0x1UL << STM32_GCCFG_PDEN_Pos) // 0x00080000 #define STM32_GCCFG_PDEN STM32_GCCFG_PDEN_Msk // Primary detection (PD) mode enable*/ + #define STM32_GCCFG_SDEN_Pos (20U) -#define STM32_GCCFG_SDEN_Msk (0x1UL << STM32_GCCFG_SDEN_Pos) // 0x00100000 */ -#define STM32_GCCFG_SDEN STM32_GCCFG_SDEN_Msk // Secondary detection (SD) mode enable */ +#define STM32_GCCFG_SDEN_Msk (0x1UL << STM32_GCCFG_SDEN_Pos) // 0x00100000 +#define STM32_GCCFG_SDEN STM32_GCCFG_SDEN_Msk // Secondary detection (SD) mode enable + #define STM32_GCCFG_VBDEN_Pos (21U) -#define STM32_GCCFG_VBDEN_Msk (0x1UL << STM32_GCCFG_VBDEN_Pos) // 0x00200000 */ -#define STM32_GCCFG_VBDEN STM32_GCCFG_VBDEN_Msk // VBUS mode enable */ +#define STM32_GCCFG_VBDEN_Msk (0x1UL << STM32_GCCFG_VBDEN_Pos) // 0x00200000 +#define STM32_GCCFG_VBDEN STM32_GCCFG_VBDEN_Msk // VBUS mode enable + #define STM32_GCCFG_OTGIDEN_Pos (22U) -#define STM32_GCCFG_OTGIDEN_Msk (0x1UL << STM32_GCCFG_OTGIDEN_Pos) // 0x00400000 */ -#define STM32_GCCFG_OTGIDEN STM32_GCCFG_OTGIDEN_Msk // OTG Id enable */ +#define STM32_GCCFG_OTGIDEN_Msk (0x1UL << STM32_GCCFG_OTGIDEN_Pos) // 0x00400000 +#define STM32_GCCFG_OTGIDEN STM32_GCCFG_OTGIDEN_Msk // OTG Id enable + #define STM32_GCCFG_PHYHSEN_Pos (23U) -#define STM32_GCCFG_PHYHSEN_Msk (0x1UL << STM32_GCCFG_PHYHSEN_Pos) // 0x00800000 */ -#define STM32_GCCFG_PHYHSEN STM32_GCCFG_PHYHSEN_Msk // HS PHY enable */ +#define STM32_GCCFG_PHYHSEN_Msk (0x1UL << STM32_GCCFG_PHYHSEN_Pos) // 0x00800000 +#define STM32_GCCFG_PHYHSEN STM32_GCCFG_PHYHSEN_Msk // HS PHY enable + +// TODO stm32u5a5 SDEN is 22nd bit, conflict with 20th bit above +//#define STM32_GCCFG_SDEN_Pos (22U) +//#define STM32_GCCFG_SDEN_Msk (0x1U << STM32_GCCFG_SDEN_Pos) // 0x00400000 +//#define STM32_GCCFG_SDEN STM32_GCCFG_SDEN_Msk // Secondary detection (PD) mode enable + +// TODO stm32u5a5 VBVALOVA is 23rd bit, conflict with PHYHSEN bit above +#define STM32_GCCFG_VBVALOVAL_Pos (23U) +#define STM32_GCCFG_VBVALOVAL_Msk (0x1U << STM32_GCCFG_VBVALOVAL_Pos) // 0x00800000 +#define STM32_GCCFG_VBVALOVAL STM32_GCCFG_VBVALOVAL_Msk // Value of VBUSVLDEXT0 femtoPHY input + +#define STM32_GCCFG_VBVALEXTOEN_Pos (24U) +#define STM32_GCCFG_VBVALEXTOEN_Msk (0x1U << STM32_GCCFG_VBVALEXTOEN_Pos) // 0x01000000 +#define STM32_GCCFG_VBVALEXTOEN STM32_GCCFG_VBVALEXTOEN_Msk // Enables of VBUSVLDEXT0 femtoPHY input override + +#define STM32_GCCFG_PULLDOWNEN_Pos (25U) +#define STM32_GCCFG_PULLDOWNEN_Msk (0x1U << STM32_GCCFG_PULLDOWNEN_Pos) // 0x02000000 +#define STM32_GCCFG_PULLDOWNEN STM32_GCCFG_PULLDOWNEN_Msk // Enables of femtoPHY pulldown resistors, used when ID PAD is disabled + /******************** Bit definition for DEACHINTMSK register ********************/ #define DEACHINTMSK_IEP1INTM_Pos (1U) -#define DEACHINTMSK_IEP1INTM_Msk (0x1UL << DEACHINTMSK_IEP1INTM_Pos) // 0x00000002 */ -#define DEACHINTMSK_IEP1INTM DEACHINTMSK_IEP1INTM_Msk // IN Endpoint 1 interrupt mask bit */ +#define DEACHINTMSK_IEP1INTM_Msk (0x1UL << DEACHINTMSK_IEP1INTM_Pos) // 0x00000002 +#define DEACHINTMSK_IEP1INTM DEACHINTMSK_IEP1INTM_Msk // IN Endpoint 1 interrupt mask bit #define DEACHINTMSK_OEP1INTM_Pos (17U) -#define DEACHINTMSK_OEP1INTM_Msk (0x1UL << DEACHINTMSK_OEP1INTM_Pos) // 0x00020000 */ -#define DEACHINTMSK_OEP1INTM DEACHINTMSK_OEP1INTM_Msk // OUT Endpoint 1 interrupt mask bit */ +#define DEACHINTMSK_OEP1INTM_Msk (0x1UL << DEACHINTMSK_OEP1INTM_Pos) // 0x00020000 +#define DEACHINTMSK_OEP1INTM DEACHINTMSK_OEP1INTM_Msk // OUT Endpoint 1 interrupt mask bit /******************** Bit definition for CID register ********************/ #define CID_PRODUCT_ID_Pos (0U) -#define CID_PRODUCT_ID_Msk (0xFFFFFFFFUL << CID_PRODUCT_ID_Pos) // 0xFFFFFFFF */ -#define CID_PRODUCT_ID CID_PRODUCT_ID_Msk // Product ID field */ +#define CID_PRODUCT_ID_Msk (0xFFFFFFFFUL << CID_PRODUCT_ID_Pos) // 0xFFFFFFFF +#define CID_PRODUCT_ID CID_PRODUCT_ID_Msk // Product ID field /******************** Bit definition for GLPMCFG register ********************/ #define GLPMCFG_LPMEN_Pos (0U) -#define GLPMCFG_LPMEN_Msk (0x1UL << GLPMCFG_LPMEN_Pos) // 0x00000001 */ -#define GLPMCFG_LPMEN GLPMCFG_LPMEN_Msk // LPM support enable */ +#define GLPMCFG_LPMEN_Msk (0x1UL << GLPMCFG_LPMEN_Pos) // 0x00000001 +#define GLPMCFG_LPMEN GLPMCFG_LPMEN_Msk // LPM support enable #define GLPMCFG_LPMACK_Pos (1U) -#define GLPMCFG_LPMACK_Msk (0x1UL << GLPMCFG_LPMACK_Pos) // 0x00000002 */ -#define GLPMCFG_LPMACK GLPMCFG_LPMACK_Msk // LPM Token acknowledge enable */ +#define GLPMCFG_LPMACK_Msk (0x1UL << GLPMCFG_LPMACK_Pos) // 0x00000002 +#define GLPMCFG_LPMACK GLPMCFG_LPMACK_Msk // LPM Token acknowledge enable #define GLPMCFG_BESL_Pos (2U) -#define GLPMCFG_BESL_Msk (0xFUL << GLPMCFG_BESL_Pos) // 0x0000003C */ -#define GLPMCFG_BESL GLPMCFG_BESL_Msk // BESL value received with last ACKed LPM Token */ +#define GLPMCFG_BESL_Msk (0xFUL << GLPMCFG_BESL_Pos) // 0x0000003C +#define GLPMCFG_BESL GLPMCFG_BESL_Msk // BESL value received with last ACKed LPM Token #define GLPMCFG_REMWAKE_Pos (6U) -#define GLPMCFG_REMWAKE_Msk (0x1UL << GLPMCFG_REMWAKE_Pos) // 0x00000040 */ -#define GLPMCFG_REMWAKE GLPMCFG_REMWAKE_Msk // bRemoteWake value received with last ACKed LPM Token */ +#define GLPMCFG_REMWAKE_Msk (0x1UL << GLPMCFG_REMWAKE_Pos) // 0x00000040 +#define GLPMCFG_REMWAKE GLPMCFG_REMWAKE_Msk // bRemoteWake value received with last ACKed LPM Token #define GLPMCFG_L1SSEN_Pos (7U) -#define GLPMCFG_L1SSEN_Msk (0x1UL << GLPMCFG_L1SSEN_Pos) // 0x00000080 */ -#define GLPMCFG_L1SSEN GLPMCFG_L1SSEN_Msk // L1 shallow sleep enable */ +#define GLPMCFG_L1SSEN_Msk (0x1UL << GLPMCFG_L1SSEN_Pos) // 0x00000080 +#define GLPMCFG_L1SSEN GLPMCFG_L1SSEN_Msk // L1 shallow sleep enable #define GLPMCFG_BESLTHRS_Pos (8U) -#define GLPMCFG_BESLTHRS_Msk (0xFUL << GLPMCFG_BESLTHRS_Pos) // 0x00000F00 */ -#define GLPMCFG_BESLTHRS GLPMCFG_BESLTHRS_Msk // BESL threshold */ +#define GLPMCFG_BESLTHRS_Msk (0xFUL << GLPMCFG_BESLTHRS_Pos) // 0x00000F00 +#define GLPMCFG_BESLTHRS GLPMCFG_BESLTHRS_Msk // BESL threshold #define GLPMCFG_L1DSEN_Pos (12U) -#define GLPMCFG_L1DSEN_Msk (0x1UL << GLPMCFG_L1DSEN_Pos) // 0x00001000 */ -#define GLPMCFG_L1DSEN GLPMCFG_L1DSEN_Msk // L1 deep sleep enable */ +#define GLPMCFG_L1DSEN_Msk (0x1UL << GLPMCFG_L1DSEN_Pos) // 0x00001000 +#define GLPMCFG_L1DSEN GLPMCFG_L1DSEN_Msk // L1 deep sleep enable #define GLPMCFG_LPMRSP_Pos (13U) -#define GLPMCFG_LPMRSP_Msk (0x3UL << GLPMCFG_LPMRSP_Pos) // 0x00006000 */ -#define GLPMCFG_LPMRSP GLPMCFG_LPMRSP_Msk // LPM response */ +#define GLPMCFG_LPMRSP_Msk (0x3UL << GLPMCFG_LPMRSP_Pos) // 0x00006000 +#define GLPMCFG_LPMRSP GLPMCFG_LPMRSP_Msk // LPM response #define GLPMCFG_SLPSTS_Pos (15U) -#define GLPMCFG_SLPSTS_Msk (0x1UL << GLPMCFG_SLPSTS_Pos) // 0x00008000 */ -#define GLPMCFG_SLPSTS GLPMCFG_SLPSTS_Msk // Port sleep status */ +#define GLPMCFG_SLPSTS_Msk (0x1UL << GLPMCFG_SLPSTS_Pos) // 0x00008000 +#define GLPMCFG_SLPSTS GLPMCFG_SLPSTS_Msk // Port sleep status #define GLPMCFG_L1RSMOK_Pos (16U) -#define GLPMCFG_L1RSMOK_Msk (0x1UL << GLPMCFG_L1RSMOK_Pos) // 0x00010000 */ -#define GLPMCFG_L1RSMOK GLPMCFG_L1RSMOK_Msk // Sleep State Resume OK */ +#define GLPMCFG_L1RSMOK_Msk (0x1UL << GLPMCFG_L1RSMOK_Pos) // 0x00010000 +#define GLPMCFG_L1RSMOK GLPMCFG_L1RSMOK_Msk // Sleep State Resume OK #define GLPMCFG_LPMCHIDX_Pos (17U) -#define GLPMCFG_LPMCHIDX_Msk (0xFUL << GLPMCFG_LPMCHIDX_Pos) // 0x001E0000 */ -#define GLPMCFG_LPMCHIDX GLPMCFG_LPMCHIDX_Msk // LPM Channel Index */ +#define GLPMCFG_LPMCHIDX_Msk (0xFUL << GLPMCFG_LPMCHIDX_Pos) // 0x001E0000 +#define GLPMCFG_LPMCHIDX GLPMCFG_LPMCHIDX_Msk // LPM Channel Index #define GLPMCFG_LPMRCNT_Pos (21U) -#define GLPMCFG_LPMRCNT_Msk (0x7UL << GLPMCFG_LPMRCNT_Pos) // 0x00E00000 */ -#define GLPMCFG_LPMRCNT GLPMCFG_LPMRCNT_Msk // LPM retry count */ +#define GLPMCFG_LPMRCNT_Msk (0x7UL << GLPMCFG_LPMRCNT_Pos) // 0x00E00000 +#define GLPMCFG_LPMRCNT GLPMCFG_LPMRCNT_Msk // LPM retry count #define GLPMCFG_SNDLPM_Pos (24U) -#define GLPMCFG_SNDLPM_Msk (0x1UL << GLPMCFG_SNDLPM_Pos) // 0x01000000 */ -#define GLPMCFG_SNDLPM GLPMCFG_SNDLPM_Msk // Send LPM transaction */ +#define GLPMCFG_SNDLPM_Msk (0x1UL << GLPMCFG_SNDLPM_Pos) // 0x01000000 +#define GLPMCFG_SNDLPM GLPMCFG_SNDLPM_Msk // Send LPM transaction #define GLPMCFG_LPMRCNTSTS_Pos (25U) -#define GLPMCFG_LPMRCNTSTS_Msk (0x7UL << GLPMCFG_LPMRCNTSTS_Pos) // 0x0E000000 */ -#define GLPMCFG_LPMRCNTSTS GLPMCFG_LPMRCNTSTS_Msk // LPM retry count status */ +#define GLPMCFG_LPMRCNTSTS_Msk (0x7UL << GLPMCFG_LPMRCNTSTS_Pos) // 0x0E000000 +#define GLPMCFG_LPMRCNTSTS GLPMCFG_LPMRCNTSTS_Msk // LPM retry count status #define GLPMCFG_ENBESL_Pos (28U) -#define GLPMCFG_ENBESL_Msk (0x1UL << GLPMCFG_ENBESL_Pos) // 0x10000000 */ -#define GLPMCFG_ENBESL GLPMCFG_ENBESL_Msk // Enable best effort service latency */ +#define GLPMCFG_ENBESL_Msk (0x1UL << GLPMCFG_ENBESL_Pos) // 0x10000000 +#define GLPMCFG_ENBESL GLPMCFG_ENBESL_Msk // Enable best effort service latency /******************** Bit definition for DIEPEACHMSK1 register ********************/ #define DIEPEACHMSK1_XFRCM_Pos (0U) -#define DIEPEACHMSK1_XFRCM_Msk (0x1UL << DIEPEACHMSK1_XFRCM_Pos) // 0x00000001 */ -#define DIEPEACHMSK1_XFRCM DIEPEACHMSK1_XFRCM_Msk // Transfer completed interrupt mask */ +#define DIEPEACHMSK1_XFRCM_Msk (0x1UL << DIEPEACHMSK1_XFRCM_Pos) // 0x00000001 +#define DIEPEACHMSK1_XFRCM DIEPEACHMSK1_XFRCM_Msk // Transfer completed interrupt mask #define DIEPEACHMSK1_EPDM_Pos (1U) -#define DIEPEACHMSK1_EPDM_Msk (0x1UL << DIEPEACHMSK1_EPDM_Pos) // 0x00000002 */ -#define DIEPEACHMSK1_EPDM DIEPEACHMSK1_EPDM_Msk // Endpoint disabled interrupt mask */ +#define DIEPEACHMSK1_EPDM_Msk (0x1UL << DIEPEACHMSK1_EPDM_Pos) // 0x00000002 +#define DIEPEACHMSK1_EPDM DIEPEACHMSK1_EPDM_Msk // Endpoint disabled interrupt mask #define DIEPEACHMSK1_TOM_Pos (3U) -#define DIEPEACHMSK1_TOM_Msk (0x1UL << DIEPEACHMSK1_TOM_Pos) // 0x00000008 */ -#define DIEPEACHMSK1_TOM DIEPEACHMSK1_TOM_Msk // Timeout condition mask (nonisochronous endpoints) */ +#define DIEPEACHMSK1_TOM_Msk (0x1UL << DIEPEACHMSK1_TOM_Pos) // 0x00000008 +#define DIEPEACHMSK1_TOM DIEPEACHMSK1_TOM_Msk // Timeout condition mask (nonisochronous endpoints) #define DIEPEACHMSK1_ITTXFEMSK_Pos (4U) -#define DIEPEACHMSK1_ITTXFEMSK_Msk (0x1UL << DIEPEACHMSK1_ITTXFEMSK_Pos) // 0x00000010 */ -#define DIEPEACHMSK1_ITTXFEMSK DIEPEACHMSK1_ITTXFEMSK_Msk // IN token received when TxFIFO empty mask */ +#define DIEPEACHMSK1_ITTXFEMSK_Msk (0x1UL << DIEPEACHMSK1_ITTXFEMSK_Pos) // 0x00000010 +#define DIEPEACHMSK1_ITTXFEMSK DIEPEACHMSK1_ITTXFEMSK_Msk // IN token received when TxFIFO empty mask #define DIEPEACHMSK1_INEPNMM_Pos (5U) -#define DIEPEACHMSK1_INEPNMM_Msk (0x1UL << DIEPEACHMSK1_INEPNMM_Pos) // 0x00000020 */ -#define DIEPEACHMSK1_INEPNMM DIEPEACHMSK1_INEPNMM_Msk // IN token received with EP mismatch mask */ +#define DIEPEACHMSK1_INEPNMM_Msk (0x1UL << DIEPEACHMSK1_INEPNMM_Pos) // 0x00000020 +#define DIEPEACHMSK1_INEPNMM DIEPEACHMSK1_INEPNMM_Msk // IN token received with EP mismatch mask #define DIEPEACHMSK1_INEPNEM_Pos (6U) -#define DIEPEACHMSK1_INEPNEM_Msk (0x1UL << DIEPEACHMSK1_INEPNEM_Pos) // 0x00000040 */ -#define DIEPEACHMSK1_INEPNEM DIEPEACHMSK1_INEPNEM_Msk // IN endpoint NAK effective mask */ +#define DIEPEACHMSK1_INEPNEM_Msk (0x1UL << DIEPEACHMSK1_INEPNEM_Pos) // 0x00000040 +#define DIEPEACHMSK1_INEPNEM DIEPEACHMSK1_INEPNEM_Msk // IN endpoint NAK effective mask #define DIEPEACHMSK1_TXFURM_Pos (8U) -#define DIEPEACHMSK1_TXFURM_Msk (0x1UL << DIEPEACHMSK1_TXFURM_Pos) // 0x00000100 */ -#define DIEPEACHMSK1_TXFURM DIEPEACHMSK1_TXFURM_Msk // FIFO underrun mask */ +#define DIEPEACHMSK1_TXFURM_Msk (0x1UL << DIEPEACHMSK1_TXFURM_Pos) // 0x00000100 +#define DIEPEACHMSK1_TXFURM DIEPEACHMSK1_TXFURM_Msk // FIFO underrun mask #define DIEPEACHMSK1_BIM_Pos (9U) -#define DIEPEACHMSK1_BIM_Msk (0x1UL << DIEPEACHMSK1_BIM_Pos) // 0x00000200 */ -#define DIEPEACHMSK1_BIM DIEPEACHMSK1_BIM_Msk // BNA interrupt mask */ +#define DIEPEACHMSK1_BIM_Msk (0x1UL << DIEPEACHMSK1_BIM_Pos) // 0x00000200 +#define DIEPEACHMSK1_BIM DIEPEACHMSK1_BIM_Msk // BNA interrupt mask #define DIEPEACHMSK1_NAKM_Pos (13U) -#define DIEPEACHMSK1_NAKM_Msk (0x1UL << DIEPEACHMSK1_NAKM_Pos) // 0x00002000 */ -#define DIEPEACHMSK1_NAKM DIEPEACHMSK1_NAKM_Msk // NAK interrupt mask */ +#define DIEPEACHMSK1_NAKM_Msk (0x1UL << DIEPEACHMSK1_NAKM_Pos) // 0x00002000 +#define DIEPEACHMSK1_NAKM DIEPEACHMSK1_NAKM_Msk // NAK interrupt mask /******************** Bit definition for HPRT register ********************/ #define HPRT_PCSTS_Pos (0U) -#define HPRT_PCSTS_Msk (0x1UL << HPRT_PCSTS_Pos) // 0x00000001 */ -#define HPRT_PCSTS HPRT_PCSTS_Msk // Port connect status */ +#define HPRT_PCSTS_Msk (0x1UL << HPRT_PCSTS_Pos) // 0x00000001 +#define HPRT_PCSTS HPRT_PCSTS_Msk // Port connect status #define HPRT_PCDET_Pos (1U) -#define HPRT_PCDET_Msk (0x1UL << HPRT_PCDET_Pos) // 0x00000002 */ -#define HPRT_PCDET HPRT_PCDET_Msk // Port connect detected */ +#define HPRT_PCDET_Msk (0x1UL << HPRT_PCDET_Pos) // 0x00000002 +#define HPRT_PCDET HPRT_PCDET_Msk // Port connect detected #define HPRT_PENA_Pos (2U) -#define HPRT_PENA_Msk (0x1UL << HPRT_PENA_Pos) // 0x00000004 */ -#define HPRT_PENA HPRT_PENA_Msk // Port enable */ +#define HPRT_PENA_Msk (0x1UL << HPRT_PENA_Pos) // 0x00000004 +#define HPRT_PENA HPRT_PENA_Msk // Port enable #define HPRT_PENCHNG_Pos (3U) -#define HPRT_PENCHNG_Msk (0x1UL << HPRT_PENCHNG_Pos) // 0x00000008 */ -#define HPRT_PENCHNG HPRT_PENCHNG_Msk // Port enable/disable change */ +#define HPRT_PENCHNG_Msk (0x1UL << HPRT_PENCHNG_Pos) // 0x00000008 +#define HPRT_PENCHNG HPRT_PENCHNG_Msk // Port enable/disable change #define HPRT_POCA_Pos (4U) -#define HPRT_POCA_Msk (0x1UL << HPRT_POCA_Pos) // 0x00000010 */ -#define HPRT_POCA HPRT_POCA_Msk // Port overcurrent active */ +#define HPRT_POCA_Msk (0x1UL << HPRT_POCA_Pos) // 0x00000010 +#define HPRT_POCA HPRT_POCA_Msk // Port overcurrent active #define HPRT_POCCHNG_Pos (5U) -#define HPRT_POCCHNG_Msk (0x1UL << HPRT_POCCHNG_Pos) // 0x00000020 */ -#define HPRT_POCCHNG HPRT_POCCHNG_Msk // Port overcurrent change */ +#define HPRT_POCCHNG_Msk (0x1UL << HPRT_POCCHNG_Pos) // 0x00000020 +#define HPRT_POCCHNG HPRT_POCCHNG_Msk // Port overcurrent change #define HPRT_PRES_Pos (6U) -#define HPRT_PRES_Msk (0x1UL << HPRT_PRES_Pos) // 0x00000040 */ -#define HPRT_PRES HPRT_PRES_Msk // Port resume */ +#define HPRT_PRES_Msk (0x1UL << HPRT_PRES_Pos) // 0x00000040 +#define HPRT_PRES HPRT_PRES_Msk // Port resume #define HPRT_PSUSP_Pos (7U) -#define HPRT_PSUSP_Msk (0x1UL << HPRT_PSUSP_Pos) // 0x00000080 */ -#define HPRT_PSUSP HPRT_PSUSP_Msk // Port suspend */ +#define HPRT_PSUSP_Msk (0x1UL << HPRT_PSUSP_Pos) // 0x00000080 +#define HPRT_PSUSP HPRT_PSUSP_Msk // Port suspend #define HPRT_PRST_Pos (8U) -#define HPRT_PRST_Msk (0x1UL << HPRT_PRST_Pos) // 0x00000100 */ -#define HPRT_PRST HPRT_PRST_Msk // Port reset */ +#define HPRT_PRST_Msk (0x1UL << HPRT_PRST_Pos) // 0x00000100 +#define HPRT_PRST HPRT_PRST_Msk // Port reset #define HPRT_PLSTS_Pos (10U) -#define HPRT_PLSTS_Msk (0x3UL << HPRT_PLSTS_Pos) // 0x00000C00 */ -#define HPRT_PLSTS HPRT_PLSTS_Msk // Port line status */ -#define HPRT_PLSTS_0 (0x1UL << HPRT_PLSTS_Pos) // 0x00000400 */ -#define HPRT_PLSTS_1 (0x2UL << HPRT_PLSTS_Pos) // 0x00000800 */ +#define HPRT_PLSTS_Msk (0x3UL << HPRT_PLSTS_Pos) // 0x00000C00 +#define HPRT_PLSTS HPRT_PLSTS_Msk // Port line status +#define HPRT_PLSTS_0 (0x1UL << HPRT_PLSTS_Pos) // 0x00000400 +#define HPRT_PLSTS_1 (0x2UL << HPRT_PLSTS_Pos) // 0x00000800 #define HPRT_PPWR_Pos (12U) -#define HPRT_PPWR_Msk (0x1UL << HPRT_PPWR_Pos) // 0x00001000 */ -#define HPRT_PPWR HPRT_PPWR_Msk // Port power */ +#define HPRT_PPWR_Msk (0x1UL << HPRT_PPWR_Pos) // 0x00001000 +#define HPRT_PPWR HPRT_PPWR_Msk // Port power #define HPRT_PTCTL_Pos (13U) -#define HPRT_PTCTL_Msk (0xFUL << HPRT_PTCTL_Pos) // 0x0001E000 */ -#define HPRT_PTCTL HPRT_PTCTL_Msk // Port test control */ -#define HPRT_PTCTL_0 (0x1UL << HPRT_PTCTL_Pos) // 0x00002000 */ -#define HPRT_PTCTL_1 (0x2UL << HPRT_PTCTL_Pos) // 0x00004000 */ -#define HPRT_PTCTL_2 (0x4UL << HPRT_PTCTL_Pos) // 0x00008000 */ -#define HPRT_PTCTL_3 (0x8UL << HPRT_PTCTL_Pos) // 0x00010000 */ +#define HPRT_PTCTL_Msk (0xFUL << HPRT_PTCTL_Pos) // 0x0001E000 +#define HPRT_PTCTL HPRT_PTCTL_Msk // Port test control +#define HPRT_PTCTL_0 (0x1UL << HPRT_PTCTL_Pos) // 0x00002000 +#define HPRT_PTCTL_1 (0x2UL << HPRT_PTCTL_Pos) // 0x00004000 +#define HPRT_PTCTL_2 (0x4UL << HPRT_PTCTL_Pos) // 0x00008000 +#define HPRT_PTCTL_3 (0x8UL << HPRT_PTCTL_Pos) // 0x00010000 #define HPRT_PSPD_Pos (17U) -#define HPRT_PSPD_Msk (0x3UL << HPRT_PSPD_Pos) // 0x00060000 */ -#define HPRT_PSPD HPRT_PSPD_Msk // Port speed */ -#define HPRT_PSPD_0 (0x1UL << HPRT_PSPD_Pos) // 0x00020000 */ -#define HPRT_PSPD_1 (0x2UL << HPRT_PSPD_Pos) // 0x00040000 */ +#define HPRT_PSPD_Msk (0x3UL << HPRT_PSPD_Pos) // 0x00060000 +#define HPRT_PSPD HPRT_PSPD_Msk // Port speed +#define HPRT_PSPD_0 (0x1UL << HPRT_PSPD_Pos) // 0x00020000 +#define HPRT_PSPD_1 (0x2UL << HPRT_PSPD_Pos) // 0x00040000 /******************** Bit definition for DOEPEACHMSK1 register ********************/ #define DOEPEACHMSK1_XFRCM_Pos (0U) -#define DOEPEACHMSK1_XFRCM_Msk (0x1UL << DOEPEACHMSK1_XFRCM_Pos) // 0x00000001 */ -#define DOEPEACHMSK1_XFRCM DOEPEACHMSK1_XFRCM_Msk // Transfer completed interrupt mask */ +#define DOEPEACHMSK1_XFRCM_Msk (0x1UL << DOEPEACHMSK1_XFRCM_Pos) // 0x00000001 +#define DOEPEACHMSK1_XFRCM DOEPEACHMSK1_XFRCM_Msk // Transfer completed interrupt mask #define DOEPEACHMSK1_EPDM_Pos (1U) -#define DOEPEACHMSK1_EPDM_Msk (0x1UL << DOEPEACHMSK1_EPDM_Pos) // 0x00000002 */ -#define DOEPEACHMSK1_EPDM DOEPEACHMSK1_EPDM_Msk // Endpoint disabled interrupt mask */ +#define DOEPEACHMSK1_EPDM_Msk (0x1UL << DOEPEACHMSK1_EPDM_Pos) // 0x00000002 +#define DOEPEACHMSK1_EPDM DOEPEACHMSK1_EPDM_Msk // Endpoint disabled interrupt mask #define DOEPEACHMSK1_TOM_Pos (3U) -#define DOEPEACHMSK1_TOM_Msk (0x1UL << DOEPEACHMSK1_TOM_Pos) // 0x00000008 */ -#define DOEPEACHMSK1_TOM DOEPEACHMSK1_TOM_Msk // Timeout condition mask */ +#define DOEPEACHMSK1_TOM_Msk (0x1UL << DOEPEACHMSK1_TOM_Pos) // 0x00000008 +#define DOEPEACHMSK1_TOM DOEPEACHMSK1_TOM_Msk // Timeout condition mask #define DOEPEACHMSK1_ITTXFEMSK_Pos (4U) -#define DOEPEACHMSK1_ITTXFEMSK_Msk (0x1UL << DOEPEACHMSK1_ITTXFEMSK_Pos) // 0x00000010 */ -#define DOEPEACHMSK1_ITTXFEMSK DOEPEACHMSK1_ITTXFEMSK_Msk // IN token received when TxFIFO empty mask */ +#define DOEPEACHMSK1_ITTXFEMSK_Msk (0x1UL << DOEPEACHMSK1_ITTXFEMSK_Pos) // 0x00000010 +#define DOEPEACHMSK1_ITTXFEMSK DOEPEACHMSK1_ITTXFEMSK_Msk // IN token received when TxFIFO empty mask #define DOEPEACHMSK1_INEPNMM_Pos (5U) -#define DOEPEACHMSK1_INEPNMM_Msk (0x1UL << DOEPEACHMSK1_INEPNMM_Pos) // 0x00000020 */ -#define DOEPEACHMSK1_INEPNMM DOEPEACHMSK1_INEPNMM_Msk // IN token received with EP mismatch mask */ +#define DOEPEACHMSK1_INEPNMM_Msk (0x1UL << DOEPEACHMSK1_INEPNMM_Pos) // 0x00000020 +#define DOEPEACHMSK1_INEPNMM DOEPEACHMSK1_INEPNMM_Msk // IN token received with EP mismatch mask #define DOEPEACHMSK1_INEPNEM_Pos (6U) -#define DOEPEACHMSK1_INEPNEM_Msk (0x1UL << DOEPEACHMSK1_INEPNEM_Pos) // 0x00000040 */ -#define DOEPEACHMSK1_INEPNEM DOEPEACHMSK1_INEPNEM_Msk // IN endpoint NAK effective mask */ +#define DOEPEACHMSK1_INEPNEM_Msk (0x1UL << DOEPEACHMSK1_INEPNEM_Pos) // 0x00000040 +#define DOEPEACHMSK1_INEPNEM DOEPEACHMSK1_INEPNEM_Msk // IN endpoint NAK effective mask #define DOEPEACHMSK1_TXFURM_Pos (8U) -#define DOEPEACHMSK1_TXFURM_Msk (0x1UL << DOEPEACHMSK1_TXFURM_Pos) // 0x00000100 */ -#define DOEPEACHMSK1_TXFURM DOEPEACHMSK1_TXFURM_Msk // OUT packet error mask */ +#define DOEPEACHMSK1_TXFURM_Msk (0x1UL << DOEPEACHMSK1_TXFURM_Pos) // 0x00000100 +#define DOEPEACHMSK1_TXFURM DOEPEACHMSK1_TXFURM_Msk // OUT packet error mask #define DOEPEACHMSK1_BIM_Pos (9U) -#define DOEPEACHMSK1_BIM_Msk (0x1UL << DOEPEACHMSK1_BIM_Pos) // 0x00000200 */ -#define DOEPEACHMSK1_BIM DOEPEACHMSK1_BIM_Msk // BNA interrupt mask */ +#define DOEPEACHMSK1_BIM_Msk (0x1UL << DOEPEACHMSK1_BIM_Pos) // 0x00000200 +#define DOEPEACHMSK1_BIM DOEPEACHMSK1_BIM_Msk // BNA interrupt mask #define DOEPEACHMSK1_BERRM_Pos (12U) -#define DOEPEACHMSK1_BERRM_Msk (0x1UL << DOEPEACHMSK1_BERRM_Pos) // 0x00001000 */ -#define DOEPEACHMSK1_BERRM DOEPEACHMSK1_BERRM_Msk // Bubble error interrupt mask */ +#define DOEPEACHMSK1_BERRM_Msk (0x1UL << DOEPEACHMSK1_BERRM_Pos) // 0x00001000 +#define DOEPEACHMSK1_BERRM DOEPEACHMSK1_BERRM_Msk // Bubble error interrupt mask #define DOEPEACHMSK1_NAKM_Pos (13U) -#define DOEPEACHMSK1_NAKM_Msk (0x1UL << DOEPEACHMSK1_NAKM_Pos) // 0x00002000 */ -#define DOEPEACHMSK1_NAKM DOEPEACHMSK1_NAKM_Msk // NAK interrupt mask */ +#define DOEPEACHMSK1_NAKM_Msk (0x1UL << DOEPEACHMSK1_NAKM_Pos) // 0x00002000 +#define DOEPEACHMSK1_NAKM DOEPEACHMSK1_NAKM_Msk // NAK interrupt mask #define DOEPEACHMSK1_NYETM_Pos (14U) -#define DOEPEACHMSK1_NYETM_Msk (0x1UL << DOEPEACHMSK1_NYETM_Pos) // 0x00004000 */ -#define DOEPEACHMSK1_NYETM DOEPEACHMSK1_NYETM_Msk // NYET interrupt mask */ +#define DOEPEACHMSK1_NYETM_Msk (0x1UL << DOEPEACHMSK1_NYETM_Pos) // 0x00004000 +#define DOEPEACHMSK1_NYETM DOEPEACHMSK1_NYETM_Msk // NYET interrupt mask /******************** Bit definition for HPTXFSIZ register ********************/ #define HPTXFSIZ_PTXSA_Pos (0U) -#define HPTXFSIZ_PTXSA_Msk (0xFFFFUL << HPTXFSIZ_PTXSA_Pos) // 0x0000FFFF */ -#define HPTXFSIZ_PTXSA HPTXFSIZ_PTXSA_Msk // Host periodic TxFIFO start address */ +#define HPTXFSIZ_PTXSA_Msk (0xFFFFUL << HPTXFSIZ_PTXSA_Pos) // 0x0000FFFF +#define HPTXFSIZ_PTXSA HPTXFSIZ_PTXSA_Msk // Host periodic TxFIFO start address #define HPTXFSIZ_PTXFD_Pos (16U) -#define HPTXFSIZ_PTXFD_Msk (0xFFFFUL << HPTXFSIZ_PTXFD_Pos) // 0xFFFF0000 */ -#define HPTXFSIZ_PTXFD HPTXFSIZ_PTXFD_Msk // Host periodic TxFIFO depth */ +#define HPTXFSIZ_PTXFD_Msk (0xFFFFUL << HPTXFSIZ_PTXFD_Pos) // 0xFFFF0000 +#define HPTXFSIZ_PTXFD HPTXFSIZ_PTXFD_Msk // Host periodic TxFIFO depth /******************** Bit definition for DIEPCTL register ********************/ #define DIEPCTL_MPSIZ_Pos (0U) -#define DIEPCTL_MPSIZ_Msk (0x7FFUL << DIEPCTL_MPSIZ_Pos) // 0x000007FF */ -#define DIEPCTL_MPSIZ DIEPCTL_MPSIZ_Msk // Maximum packet size */ +#define DIEPCTL_MPSIZ_Msk (0x7FFUL << DIEPCTL_MPSIZ_Pos) // 0x000007FF +#define DIEPCTL_MPSIZ DIEPCTL_MPSIZ_Msk // Maximum packet size #define DIEPCTL_USBAEP_Pos (15U) -#define DIEPCTL_USBAEP_Msk (0x1UL << DIEPCTL_USBAEP_Pos) // 0x00008000 */ -#define DIEPCTL_USBAEP DIEPCTL_USBAEP_Msk // USB active endpoint */ +#define DIEPCTL_USBAEP_Msk (0x1UL << DIEPCTL_USBAEP_Pos) // 0x00008000 +#define DIEPCTL_USBAEP DIEPCTL_USBAEP_Msk // USB active endpoint #define DIEPCTL_EONUM_DPID_Pos (16U) -#define DIEPCTL_EONUM_DPID_Msk (0x1UL << DIEPCTL_EONUM_DPID_Pos) // 0x00010000 */ -#define DIEPCTL_EONUM_DPID DIEPCTL_EONUM_DPID_Msk // Even/odd frame */ +#define DIEPCTL_EONUM_DPID_Msk (0x1UL << DIEPCTL_EONUM_DPID_Pos) // 0x00010000 +#define DIEPCTL_EONUM_DPID DIEPCTL_EONUM_DPID_Msk // Even/odd frame #define DIEPCTL_NAKSTS_Pos (17U) -#define DIEPCTL_NAKSTS_Msk (0x1UL << DIEPCTL_NAKSTS_Pos) // 0x00020000 */ -#define DIEPCTL_NAKSTS DIEPCTL_NAKSTS_Msk // NAK status */ +#define DIEPCTL_NAKSTS_Msk (0x1UL << DIEPCTL_NAKSTS_Pos) // 0x00020000 +#define DIEPCTL_NAKSTS DIEPCTL_NAKSTS_Msk // NAK status #define DIEPCTL_EPTYP_Pos (18U) -#define DIEPCTL_EPTYP_Msk (0x3UL << DIEPCTL_EPTYP_Pos) // 0x000C0000 */ -#define DIEPCTL_EPTYP DIEPCTL_EPTYP_Msk // Endpoint type */ -#define DIEPCTL_EPTYP_0 (0x1UL << DIEPCTL_EPTYP_Pos) // 0x00040000 */ -#define DIEPCTL_EPTYP_1 (0x2UL << DIEPCTL_EPTYP_Pos) // 0x00080000 */ +#define DIEPCTL_EPTYP_Msk (0x3UL << DIEPCTL_EPTYP_Pos) // 0x000C0000 +#define DIEPCTL_EPTYP DIEPCTL_EPTYP_Msk // Endpoint type +#define DIEPCTL_EPTYP_0 (0x1UL << DIEPCTL_EPTYP_Pos) // 0x00040000 +#define DIEPCTL_EPTYP_1 (0x2UL << DIEPCTL_EPTYP_Pos) // 0x00080000 #define DIEPCTL_STALL_Pos (21U) -#define DIEPCTL_STALL_Msk (0x1UL << DIEPCTL_STALL_Pos) // 0x00200000 */ -#define DIEPCTL_STALL DIEPCTL_STALL_Msk // STALL handshake */ +#define DIEPCTL_STALL_Msk (0x1UL << DIEPCTL_STALL_Pos) // 0x00200000 +#define DIEPCTL_STALL DIEPCTL_STALL_Msk // STALL handshake #define DIEPCTL_TXFNUM_Pos (22U) -#define DIEPCTL_TXFNUM_Msk (0xFUL << DIEPCTL_TXFNUM_Pos) // 0x03C00000 */ -#define DIEPCTL_TXFNUM DIEPCTL_TXFNUM_Msk // TxFIFO number */ -#define DIEPCTL_TXFNUM_0 (0x1UL << DIEPCTL_TXFNUM_Pos) // 0x00400000 */ -#define DIEPCTL_TXFNUM_1 (0x2UL << DIEPCTL_TXFNUM_Pos) // 0x00800000 */ -#define DIEPCTL_TXFNUM_2 (0x4UL << DIEPCTL_TXFNUM_Pos) // 0x01000000 */ -#define DIEPCTL_TXFNUM_3 (0x8UL << DIEPCTL_TXFNUM_Pos) // 0x02000000 */ +#define DIEPCTL_TXFNUM_Msk (0xFUL << DIEPCTL_TXFNUM_Pos) // 0x03C00000 +#define DIEPCTL_TXFNUM DIEPCTL_TXFNUM_Msk // TxFIFO number +#define DIEPCTL_TXFNUM_0 (0x1UL << DIEPCTL_TXFNUM_Pos) // 0x00400000 +#define DIEPCTL_TXFNUM_1 (0x2UL << DIEPCTL_TXFNUM_Pos) // 0x00800000 +#define DIEPCTL_TXFNUM_2 (0x4UL << DIEPCTL_TXFNUM_Pos) // 0x01000000 +#define DIEPCTL_TXFNUM_3 (0x8UL << DIEPCTL_TXFNUM_Pos) // 0x02000000 #define DIEPCTL_CNAK_Pos (26U) -#define DIEPCTL_CNAK_Msk (0x1UL << DIEPCTL_CNAK_Pos) // 0x04000000 */ -#define DIEPCTL_CNAK DIEPCTL_CNAK_Msk // Clear NAK */ +#define DIEPCTL_CNAK_Msk (0x1UL << DIEPCTL_CNAK_Pos) // 0x04000000 +#define DIEPCTL_CNAK DIEPCTL_CNAK_Msk // Clear NAK #define DIEPCTL_SNAK_Pos (27U) -#define DIEPCTL_SNAK_Msk (0x1UL << DIEPCTL_SNAK_Pos) // 0x08000000 */ -#define DIEPCTL_SNAK DIEPCTL_SNAK_Msk // Set NAK */ +#define DIEPCTL_SNAK_Msk (0x1UL << DIEPCTL_SNAK_Pos) // 0x08000000 +#define DIEPCTL_SNAK DIEPCTL_SNAK_Msk // Set NAK #define DIEPCTL_SD0PID_SEVNFRM_Pos (28U) -#define DIEPCTL_SD0PID_SEVNFRM_Msk (0x1UL << DIEPCTL_SD0PID_SEVNFRM_Pos) // 0x10000000 */ -#define DIEPCTL_SD0PID_SEVNFRM DIEPCTL_SD0PID_SEVNFRM_Msk // Set DATA0 PID */ +#define DIEPCTL_SD0PID_SEVNFRM_Msk (0x1UL << DIEPCTL_SD0PID_SEVNFRM_Pos) // 0x10000000 +#define DIEPCTL_SD0PID_SEVNFRM DIEPCTL_SD0PID_SEVNFRM_Msk // Set DATA0 PID #define DIEPCTL_SODDFRM_Pos (29U) -#define DIEPCTL_SODDFRM_Msk (0x1UL << DIEPCTL_SODDFRM_Pos) // 0x20000000 */ -#define DIEPCTL_SODDFRM DIEPCTL_SODDFRM_Msk // Set odd frame */ +#define DIEPCTL_SODDFRM_Msk (0x1UL << DIEPCTL_SODDFRM_Pos) // 0x20000000 +#define DIEPCTL_SODDFRM DIEPCTL_SODDFRM_Msk // Set odd frame #define DIEPCTL_EPDIS_Pos (30U) -#define DIEPCTL_EPDIS_Msk (0x1UL << DIEPCTL_EPDIS_Pos) // 0x40000000 */ -#define DIEPCTL_EPDIS DIEPCTL_EPDIS_Msk // Endpoint disable */ +#define DIEPCTL_EPDIS_Msk (0x1UL << DIEPCTL_EPDIS_Pos) // 0x40000000 +#define DIEPCTL_EPDIS DIEPCTL_EPDIS_Msk // Endpoint disable #define DIEPCTL_EPENA_Pos (31U) -#define DIEPCTL_EPENA_Msk (0x1UL << DIEPCTL_EPENA_Pos) // 0x80000000 */ -#define DIEPCTL_EPENA DIEPCTL_EPENA_Msk // Endpoint enable */ +#define DIEPCTL_EPENA_Msk (0x1UL << DIEPCTL_EPENA_Pos) // 0x80000000 +#define DIEPCTL_EPENA DIEPCTL_EPENA_Msk // Endpoint enable /******************** Bit definition for HCCHAR register ********************/ #define HCCHAR_MPSIZ_Pos (0U) -#define HCCHAR_MPSIZ_Msk (0x7FFUL << HCCHAR_MPSIZ_Pos) // 0x000007FF */ -#define HCCHAR_MPSIZ HCCHAR_MPSIZ_Msk // Maximum packet size */ +#define HCCHAR_MPSIZ_Msk (0x7FFUL << HCCHAR_MPSIZ_Pos) // 0x000007FF +#define HCCHAR_MPSIZ HCCHAR_MPSIZ_Msk // Maximum packet size #define HCCHAR_EPNUM_Pos (11U) -#define HCCHAR_EPNUM_Msk (0xFUL << HCCHAR_EPNUM_Pos) // 0x00007800 */ -#define HCCHAR_EPNUM HCCHAR_EPNUM_Msk // Endpoint number */ -#define HCCHAR_EPNUM_0 (0x1UL << HCCHAR_EPNUM_Pos) // 0x00000800 */ -#define HCCHAR_EPNUM_1 (0x2UL << HCCHAR_EPNUM_Pos) // 0x00001000 */ -#define HCCHAR_EPNUM_2 (0x4UL << HCCHAR_EPNUM_Pos) // 0x00002000 */ -#define HCCHAR_EPNUM_3 (0x8UL << HCCHAR_EPNUM_Pos) // 0x00004000 */ +#define HCCHAR_EPNUM_Msk (0xFUL << HCCHAR_EPNUM_Pos) // 0x00007800 +#define HCCHAR_EPNUM HCCHAR_EPNUM_Msk // Endpoint number +#define HCCHAR_EPNUM_0 (0x1UL << HCCHAR_EPNUM_Pos) // 0x00000800 +#define HCCHAR_EPNUM_1 (0x2UL << HCCHAR_EPNUM_Pos) // 0x00001000 +#define HCCHAR_EPNUM_2 (0x4UL << HCCHAR_EPNUM_Pos) // 0x00002000 +#define HCCHAR_EPNUM_3 (0x8UL << HCCHAR_EPNUM_Pos) // 0x00004000 #define HCCHAR_EPDIR_Pos (15U) -#define HCCHAR_EPDIR_Msk (0x1UL << HCCHAR_EPDIR_Pos) // 0x00008000 */ -#define HCCHAR_EPDIR HCCHAR_EPDIR_Msk // Endpoint direction */ +#define HCCHAR_EPDIR_Msk (0x1UL << HCCHAR_EPDIR_Pos) // 0x00008000 +#define HCCHAR_EPDIR HCCHAR_EPDIR_Msk // Endpoint direction #define HCCHAR_LSDEV_Pos (17U) -#define HCCHAR_LSDEV_Msk (0x1UL << HCCHAR_LSDEV_Pos) // 0x00020000 */ -#define HCCHAR_LSDEV HCCHAR_LSDEV_Msk // Low-speed device */ +#define HCCHAR_LSDEV_Msk (0x1UL << HCCHAR_LSDEV_Pos) // 0x00020000 +#define HCCHAR_LSDEV HCCHAR_LSDEV_Msk // Low-speed device #define HCCHAR_EPTYP_Pos (18U) -#define HCCHAR_EPTYP_Msk (0x3UL << HCCHAR_EPTYP_Pos) // 0x000C0000 */ -#define HCCHAR_EPTYP HCCHAR_EPTYP_Msk // Endpoint type */ -#define HCCHAR_EPTYP_0 (0x1UL << HCCHAR_EPTYP_Pos) // 0x00040000 */ -#define HCCHAR_EPTYP_1 (0x2UL << HCCHAR_EPTYP_Pos) // 0x00080000 */ +#define HCCHAR_EPTYP_Msk (0x3UL << HCCHAR_EPTYP_Pos) // 0x000C0000 +#define HCCHAR_EPTYP HCCHAR_EPTYP_Msk // Endpoint type +#define HCCHAR_EPTYP_0 (0x1UL << HCCHAR_EPTYP_Pos) // 0x00040000 +#define HCCHAR_EPTYP_1 (0x2UL << HCCHAR_EPTYP_Pos) // 0x00080000 #define HCCHAR_MC_Pos (20U) -#define HCCHAR_MC_Msk (0x3UL << HCCHAR_MC_Pos) // 0x00300000 */ -#define HCCHAR_MC HCCHAR_MC_Msk // Multi Count (MC) / Error Count (EC) */ -#define HCCHAR_MC_0 (0x1UL << HCCHAR_MC_Pos) // 0x00100000 */ -#define HCCHAR_MC_1 (0x2UL << HCCHAR_MC_Pos) // 0x00200000 */ +#define HCCHAR_MC_Msk (0x3UL << HCCHAR_MC_Pos) // 0x00300000 +#define HCCHAR_MC HCCHAR_MC_Msk // Multi Count (MC) / Error Count (EC) +#define HCCHAR_MC_0 (0x1UL << HCCHAR_MC_Pos) // 0x00100000 +#define HCCHAR_MC_1 (0x2UL << HCCHAR_MC_Pos) // 0x00200000 #define HCCHAR_DAD_Pos (22U) -#define HCCHAR_DAD_Msk (0x7FUL << HCCHAR_DAD_Pos) // 0x1FC00000 */ -#define HCCHAR_DAD HCCHAR_DAD_Msk // Device address */ -#define HCCHAR_DAD_0 (0x01UL << HCCHAR_DAD_Pos) // 0x00400000 */ -#define HCCHAR_DAD_1 (0x02UL << HCCHAR_DAD_Pos) // 0x00800000 */ -#define HCCHAR_DAD_2 (0x04UL << HCCHAR_DAD_Pos) // 0x01000000 */ -#define HCCHAR_DAD_3 (0x08UL << HCCHAR_DAD_Pos) // 0x02000000 */ -#define HCCHAR_DAD_4 (0x10UL << HCCHAR_DAD_Pos) // 0x04000000 */ -#define HCCHAR_DAD_5 (0x20UL << HCCHAR_DAD_Pos) // 0x08000000 */ -#define HCCHAR_DAD_6 (0x40UL << HCCHAR_DAD_Pos) // 0x10000000 */ +#define HCCHAR_DAD_Msk (0x7FUL << HCCHAR_DAD_Pos) // 0x1FC00000 +#define HCCHAR_DAD HCCHAR_DAD_Msk // Device address +#define HCCHAR_DAD_0 (0x01UL << HCCHAR_DAD_Pos) // 0x00400000 +#define HCCHAR_DAD_1 (0x02UL << HCCHAR_DAD_Pos) // 0x00800000 +#define HCCHAR_DAD_2 (0x04UL << HCCHAR_DAD_Pos) // 0x01000000 +#define HCCHAR_DAD_3 (0x08UL << HCCHAR_DAD_Pos) // 0x02000000 +#define HCCHAR_DAD_4 (0x10UL << HCCHAR_DAD_Pos) // 0x04000000 +#define HCCHAR_DAD_5 (0x20UL << HCCHAR_DAD_Pos) // 0x08000000 +#define HCCHAR_DAD_6 (0x40UL << HCCHAR_DAD_Pos) // 0x10000000 #define HCCHAR_ODDFRM_Pos (29U) -#define HCCHAR_ODDFRM_Msk (0x1UL << HCCHAR_ODDFRM_Pos) // 0x20000000 */ -#define HCCHAR_ODDFRM HCCHAR_ODDFRM_Msk // Odd frame */ +#define HCCHAR_ODDFRM_Msk (0x1UL << HCCHAR_ODDFRM_Pos) // 0x20000000 +#define HCCHAR_ODDFRM HCCHAR_ODDFRM_Msk // Odd frame #define HCCHAR_CHDIS_Pos (30U) -#define HCCHAR_CHDIS_Msk (0x1UL << HCCHAR_CHDIS_Pos) // 0x40000000 */ -#define HCCHAR_CHDIS HCCHAR_CHDIS_Msk // Channel disable */ +#define HCCHAR_CHDIS_Msk (0x1UL << HCCHAR_CHDIS_Pos) // 0x40000000 +#define HCCHAR_CHDIS HCCHAR_CHDIS_Msk // Channel disable #define HCCHAR_CHENA_Pos (31U) -#define HCCHAR_CHENA_Msk (0x1UL << HCCHAR_CHENA_Pos) // 0x80000000 */ -#define HCCHAR_CHENA HCCHAR_CHENA_Msk // Channel enable */ +#define HCCHAR_CHENA_Msk (0x1UL << HCCHAR_CHENA_Pos) // 0x80000000 +#define HCCHAR_CHENA HCCHAR_CHENA_Msk // Channel enable /******************** Bit definition for HCSPLT register ********************/ #define HCSPLT_PRTADDR_Pos (0U) -#define HCSPLT_PRTADDR_Msk (0x7FUL << HCSPLT_PRTADDR_Pos) // 0x0000007F */ -#define HCSPLT_PRTADDR HCSPLT_PRTADDR_Msk // Port address */ -#define HCSPLT_PRTADDR_0 (0x01UL << HCSPLT_PRTADDR_Pos) // 0x00000001 */ -#define HCSPLT_PRTADDR_1 (0x02UL << HCSPLT_PRTADDR_Pos) // 0x00000002 */ -#define HCSPLT_PRTADDR_2 (0x04UL << HCSPLT_PRTADDR_Pos) // 0x00000004 */ -#define HCSPLT_PRTADDR_3 (0x08UL << HCSPLT_PRTADDR_Pos) // 0x00000008 */ -#define HCSPLT_PRTADDR_4 (0x10UL << HCSPLT_PRTADDR_Pos) // 0x00000010 */ -#define HCSPLT_PRTADDR_5 (0x20UL << HCSPLT_PRTADDR_Pos) // 0x00000020 */ -#define HCSPLT_PRTADDR_6 (0x40UL << HCSPLT_PRTADDR_Pos) // 0x00000040 */ +#define HCSPLT_PRTADDR_Msk (0x7FUL << HCSPLT_PRTADDR_Pos) // 0x0000007F +#define HCSPLT_PRTADDR HCSPLT_PRTADDR_Msk // Port address +#define HCSPLT_PRTADDR_0 (0x01UL << HCSPLT_PRTADDR_Pos) // 0x00000001 +#define HCSPLT_PRTADDR_1 (0x02UL << HCSPLT_PRTADDR_Pos) // 0x00000002 +#define HCSPLT_PRTADDR_2 (0x04UL << HCSPLT_PRTADDR_Pos) // 0x00000004 +#define HCSPLT_PRTADDR_3 (0x08UL << HCSPLT_PRTADDR_Pos) // 0x00000008 +#define HCSPLT_PRTADDR_4 (0x10UL << HCSPLT_PRTADDR_Pos) // 0x00000010 +#define HCSPLT_PRTADDR_5 (0x20UL << HCSPLT_PRTADDR_Pos) // 0x00000020 +#define HCSPLT_PRTADDR_6 (0x40UL << HCSPLT_PRTADDR_Pos) // 0x00000040 #define HCSPLT_HUBADDR_Pos (7U) -#define HCSPLT_HUBADDR_Msk (0x7FUL << HCSPLT_HUBADDR_Pos) // 0x00003F80 */ -#define HCSPLT_HUBADDR HCSPLT_HUBADDR_Msk // Hub address */ -#define HCSPLT_HUBADDR_0 (0x01UL << HCSPLT_HUBADDR_Pos) // 0x00000080 */ -#define HCSPLT_HUBADDR_1 (0x02UL << HCSPLT_HUBADDR_Pos) // 0x00000100 */ -#define HCSPLT_HUBADDR_2 (0x04UL << HCSPLT_HUBADDR_Pos) // 0x00000200 */ -#define HCSPLT_HUBADDR_3 (0x08UL << HCSPLT_HUBADDR_Pos) // 0x00000400 */ -#define HCSPLT_HUBADDR_4 (0x10UL << HCSPLT_HUBADDR_Pos) // 0x00000800 */ -#define HCSPLT_HUBADDR_5 (0x20UL << HCSPLT_HUBADDR_Pos) // 0x00001000 */ -#define HCSPLT_HUBADDR_6 (0x40UL << HCSPLT_HUBADDR_Pos) // 0x00002000 */ +#define HCSPLT_HUBADDR_Msk (0x7FUL << HCSPLT_HUBADDR_Pos) // 0x00003F80 +#define HCSPLT_HUBADDR HCSPLT_HUBADDR_Msk // Hub address +#define HCSPLT_HUBADDR_0 (0x01UL << HCSPLT_HUBADDR_Pos) // 0x00000080 +#define HCSPLT_HUBADDR_1 (0x02UL << HCSPLT_HUBADDR_Pos) // 0x00000100 +#define HCSPLT_HUBADDR_2 (0x04UL << HCSPLT_HUBADDR_Pos) // 0x00000200 +#define HCSPLT_HUBADDR_3 (0x08UL << HCSPLT_HUBADDR_Pos) // 0x00000400 +#define HCSPLT_HUBADDR_4 (0x10UL << HCSPLT_HUBADDR_Pos) // 0x00000800 +#define HCSPLT_HUBADDR_5 (0x20UL << HCSPLT_HUBADDR_Pos) // 0x00001000 +#define HCSPLT_HUBADDR_6 (0x40UL << HCSPLT_HUBADDR_Pos) // 0x00002000 #define HCSPLT_XACTPOS_Pos (14U) -#define HCSPLT_XACTPOS_Msk (0x3UL << HCSPLT_XACTPOS_Pos) // 0x0000C000 */ -#define HCSPLT_XACTPOS HCSPLT_XACTPOS_Msk // XACTPOS */ -#define HCSPLT_XACTPOS_0 (0x1UL << HCSPLT_XACTPOS_Pos) // 0x00004000 */ -#define HCSPLT_XACTPOS_1 (0x2UL << HCSPLT_XACTPOS_Pos) // 0x00008000 */ +#define HCSPLT_XACTPOS_Msk (0x3UL << HCSPLT_XACTPOS_Pos) // 0x0000C000 +#define HCSPLT_XACTPOS HCSPLT_XACTPOS_Msk // XACTPOS +#define HCSPLT_XACTPOS_0 (0x1UL << HCSPLT_XACTPOS_Pos) // 0x00004000 +#define HCSPLT_XACTPOS_1 (0x2UL << HCSPLT_XACTPOS_Pos) // 0x00008000 #define HCSPLT_COMPLSPLT_Pos (16U) -#define HCSPLT_COMPLSPLT_Msk (0x1UL << HCSPLT_COMPLSPLT_Pos) // 0x00010000 */ -#define HCSPLT_COMPLSPLT HCSPLT_COMPLSPLT_Msk // Do complete split */ +#define HCSPLT_COMPLSPLT_Msk (0x1UL << HCSPLT_COMPLSPLT_Pos) // 0x00010000 +#define HCSPLT_COMPLSPLT HCSPLT_COMPLSPLT_Msk // Do complete split #define HCSPLT_SPLITEN_Pos (31U) -#define HCSPLT_SPLITEN_Msk (0x1UL << HCSPLT_SPLITEN_Pos) // 0x80000000 */ -#define HCSPLT_SPLITEN HCSPLT_SPLITEN_Msk // Split enable */ +#define HCSPLT_SPLITEN_Msk (0x1UL << HCSPLT_SPLITEN_Pos) // 0x80000000 +#define HCSPLT_SPLITEN HCSPLT_SPLITEN_Msk // Split enable /******************** Bit definition for HCINT register ********************/ #define HCINT_XFRC_Pos (0U) -#define HCINT_XFRC_Msk (0x1UL << HCINT_XFRC_Pos) // 0x00000001 */ -#define HCINT_XFRC HCINT_XFRC_Msk // Transfer completed */ +#define HCINT_XFRC_Msk (0x1UL << HCINT_XFRC_Pos) // 0x00000001 +#define HCINT_XFRC HCINT_XFRC_Msk // Transfer completed #define HCINT_CHH_Pos (1U) -#define HCINT_CHH_Msk (0x1UL << HCINT_CHH_Pos) // 0x00000002 */ -#define HCINT_CHH HCINT_CHH_Msk // Channel halted */ +#define HCINT_CHH_Msk (0x1UL << HCINT_CHH_Pos) // 0x00000002 +#define HCINT_CHH HCINT_CHH_Msk // Channel halted #define HCINT_AHBERR_Pos (2U) -#define HCINT_AHBERR_Msk (0x1UL << HCINT_AHBERR_Pos) // 0x00000004 */ -#define HCINT_AHBERR HCINT_AHBERR_Msk // AHB error */ +#define HCINT_AHBERR_Msk (0x1UL << HCINT_AHBERR_Pos) // 0x00000004 +#define HCINT_AHBERR HCINT_AHBERR_Msk // AHB error #define HCINT_STALL_Pos (3U) -#define HCINT_STALL_Msk (0x1UL << HCINT_STALL_Pos) // 0x00000008 */ -#define HCINT_STALL HCINT_STALL_Msk // STALL response received interrupt */ +#define HCINT_STALL_Msk (0x1UL << HCINT_STALL_Pos) // 0x00000008 +#define HCINT_STALL HCINT_STALL_Msk // STALL response received interrupt #define HCINT_NAK_Pos (4U) -#define HCINT_NAK_Msk (0x1UL << HCINT_NAK_Pos) // 0x00000010 */ -#define HCINT_NAK HCINT_NAK_Msk // NAK response received interrupt */ +#define HCINT_NAK_Msk (0x1UL << HCINT_NAK_Pos) // 0x00000010 +#define HCINT_NAK HCINT_NAK_Msk // NAK response received interrupt #define HCINT_ACK_Pos (5U) -#define HCINT_ACK_Msk (0x1UL << HCINT_ACK_Pos) // 0x00000020 */ -#define HCINT_ACK HCINT_ACK_Msk // ACK response received/transmitted interrupt */ +#define HCINT_ACK_Msk (0x1UL << HCINT_ACK_Pos) // 0x00000020 +#define HCINT_ACK HCINT_ACK_Msk // ACK response received/transmitted interrupt #define HCINT_NYET_Pos (6U) -#define HCINT_NYET_Msk (0x1UL << HCINT_NYET_Pos) // 0x00000040 */ -#define HCINT_NYET HCINT_NYET_Msk // Response received interrupt */ +#define HCINT_NYET_Msk (0x1UL << HCINT_NYET_Pos) // 0x00000040 +#define HCINT_NYET HCINT_NYET_Msk // Response received interrupt #define HCINT_TXERR_Pos (7U) -#define HCINT_TXERR_Msk (0x1UL << HCINT_TXERR_Pos) // 0x00000080 */ -#define HCINT_TXERR HCINT_TXERR_Msk // Transaction error */ +#define HCINT_TXERR_Msk (0x1UL << HCINT_TXERR_Pos) // 0x00000080 +#define HCINT_TXERR HCINT_TXERR_Msk // Transaction error #define HCINT_BBERR_Pos (8U) -#define HCINT_BBERR_Msk (0x1UL << HCINT_BBERR_Pos) // 0x00000100 */ -#define HCINT_BBERR HCINT_BBERR_Msk // Babble error */ +#define HCINT_BBERR_Msk (0x1UL << HCINT_BBERR_Pos) // 0x00000100 +#define HCINT_BBERR HCINT_BBERR_Msk // Babble error #define HCINT_FRMOR_Pos (9U) -#define HCINT_FRMOR_Msk (0x1UL << HCINT_FRMOR_Pos) // 0x00000200 */ -#define HCINT_FRMOR HCINT_FRMOR_Msk // Frame overrun */ +#define HCINT_FRMOR_Msk (0x1UL << HCINT_FRMOR_Pos) // 0x00000200 +#define HCINT_FRMOR HCINT_FRMOR_Msk // Frame overrun #define HCINT_DTERR_Pos (10U) -#define HCINT_DTERR_Msk (0x1UL << HCINT_DTERR_Pos) // 0x00000400 */ -#define HCINT_DTERR HCINT_DTERR_Msk // Data toggle error */ +#define HCINT_DTERR_Msk (0x1UL << HCINT_DTERR_Pos) // 0x00000400 +#define HCINT_DTERR HCINT_DTERR_Msk // Data toggle error /******************** Bit definition for DIEPINT register ********************/ #define DIEPINT_XFRC_Pos (0U) -#define DIEPINT_XFRC_Msk (0x1UL << DIEPINT_XFRC_Pos) // 0x00000001 */ -#define DIEPINT_XFRC DIEPINT_XFRC_Msk // Transfer completed interrupt */ +#define DIEPINT_XFRC_Msk (0x1UL << DIEPINT_XFRC_Pos) // 0x00000001 +#define DIEPINT_XFRC DIEPINT_XFRC_Msk // Transfer completed interrupt #define DIEPINT_EPDISD_Pos (1U) -#define DIEPINT_EPDISD_Msk (0x1UL << DIEPINT_EPDISD_Pos) // 0x00000002 */ -#define DIEPINT_EPDISD DIEPINT_EPDISD_Msk // Endpoint disabled interrupt */ +#define DIEPINT_EPDISD_Msk (0x1UL << DIEPINT_EPDISD_Pos) // 0x00000002 +#define DIEPINT_EPDISD DIEPINT_EPDISD_Msk // Endpoint disabled interrupt #define DIEPINT_AHBERR_Pos (2U) -#define DIEPINT_AHBERR_Msk (0x1UL << DIEPINT_AHBERR_Pos) // 0x00000004 */ -#define DIEPINT_AHBERR DIEPINT_AHBERR_Msk // AHB Error (AHBErr) during an IN transaction */ +#define DIEPINT_AHBERR_Msk (0x1UL << DIEPINT_AHBERR_Pos) // 0x00000004 +#define DIEPINT_AHBERR DIEPINT_AHBERR_Msk // AHB Error (AHBErr) during an IN transaction #define DIEPINT_TOC_Pos (3U) -#define DIEPINT_TOC_Msk (0x1UL << DIEPINT_TOC_Pos) // 0x00000008 */ -#define DIEPINT_TOC DIEPINT_TOC_Msk // Timeout condition */ +#define DIEPINT_TOC_Msk (0x1UL << DIEPINT_TOC_Pos) // 0x00000008 +#define DIEPINT_TOC DIEPINT_TOC_Msk // Timeout condition #define DIEPINT_ITTXFE_Pos (4U) -#define DIEPINT_ITTXFE_Msk (0x1UL << DIEPINT_ITTXFE_Pos) // 0x00000010 */ -#define DIEPINT_ITTXFE DIEPINT_ITTXFE_Msk // IN token received when TxFIFO is empty */ +#define DIEPINT_ITTXFE_Msk (0x1UL << DIEPINT_ITTXFE_Pos) // 0x00000010 +#define DIEPINT_ITTXFE DIEPINT_ITTXFE_Msk // IN token received when TxFIFO is empty #define DIEPINT_INEPNM_Pos (5U) -#define DIEPINT_INEPNM_Msk (0x1UL << DIEPINT_INEPNM_Pos) // 0x00000020 */ -#define DIEPINT_INEPNM DIEPINT_INEPNM_Msk // IN token received with EP mismatch */ +#define DIEPINT_INEPNM_Msk (0x1UL << DIEPINT_INEPNM_Pos) // 0x00000020 +#define DIEPINT_INEPNM DIEPINT_INEPNM_Msk // IN token received with EP mismatch #define DIEPINT_INEPNE_Pos (6U) -#define DIEPINT_INEPNE_Msk (0x1UL << DIEPINT_INEPNE_Pos) // 0x00000040 */ -#define DIEPINT_INEPNE DIEPINT_INEPNE_Msk // IN endpoint NAK effective */ +#define DIEPINT_INEPNE_Msk (0x1UL << DIEPINT_INEPNE_Pos) // 0x00000040 +#define DIEPINT_INEPNE DIEPINT_INEPNE_Msk // IN endpoint NAK effective #define DIEPINT_TXFE_Pos (7U) -#define DIEPINT_TXFE_Msk (0x1UL << DIEPINT_TXFE_Pos) // 0x00000080 */ -#define DIEPINT_TXFE DIEPINT_TXFE_Msk // Transmit FIFO empty */ +#define DIEPINT_TXFE_Msk (0x1UL << DIEPINT_TXFE_Pos) // 0x00000080 +#define DIEPINT_TXFE DIEPINT_TXFE_Msk // Transmit FIFO empty #define DIEPINT_TXFIFOUDRN_Pos (8U) -#define DIEPINT_TXFIFOUDRN_Msk (0x1UL << DIEPINT_TXFIFOUDRN_Pos) // 0x00000100 */ -#define DIEPINT_TXFIFOUDRN DIEPINT_TXFIFOUDRN_Msk // Transmit Fifo Underrun */ +#define DIEPINT_TXFIFOUDRN_Msk (0x1UL << DIEPINT_TXFIFOUDRN_Pos) // 0x00000100 +#define DIEPINT_TXFIFOUDRN DIEPINT_TXFIFOUDRN_Msk // Transmit Fifo Underrun #define DIEPINT_BNA_Pos (9U) -#define DIEPINT_BNA_Msk (0x1UL << DIEPINT_BNA_Pos) // 0x00000200 */ -#define DIEPINT_BNA DIEPINT_BNA_Msk // Buffer not available interrupt */ +#define DIEPINT_BNA_Msk (0x1UL << DIEPINT_BNA_Pos) // 0x00000200 +#define DIEPINT_BNA DIEPINT_BNA_Msk // Buffer not available interrupt #define DIEPINT_PKTDRPSTS_Pos (11U) -#define DIEPINT_PKTDRPSTS_Msk (0x1UL << DIEPINT_PKTDRPSTS_Pos) // 0x00000800 */ -#define DIEPINT_PKTDRPSTS DIEPINT_PKTDRPSTS_Msk // Packet dropped status */ +#define DIEPINT_PKTDRPSTS_Msk (0x1UL << DIEPINT_PKTDRPSTS_Pos) // 0x00000800 +#define DIEPINT_PKTDRPSTS DIEPINT_PKTDRPSTS_Msk // Packet dropped status #define DIEPINT_BERR_Pos (12U) -#define DIEPINT_BERR_Msk (0x1UL << DIEPINT_BERR_Pos) // 0x00001000 */ -#define DIEPINT_BERR DIEPINT_BERR_Msk // Babble error interrupt */ +#define DIEPINT_BERR_Msk (0x1UL << DIEPINT_BERR_Pos) // 0x00001000 +#define DIEPINT_BERR DIEPINT_BERR_Msk // Babble error interrupt #define DIEPINT_NAK_Pos (13U) -#define DIEPINT_NAK_Msk (0x1UL << DIEPINT_NAK_Pos) // 0x00002000 */ -#define DIEPINT_NAK DIEPINT_NAK_Msk // NAK interrupt */ +#define DIEPINT_NAK_Msk (0x1UL << DIEPINT_NAK_Pos) // 0x00002000 +#define DIEPINT_NAK DIEPINT_NAK_Msk // NAK interrupt /******************** Bit definition for HCINTMSK register ********************/ #define HCINTMSK_XFRCM_Pos (0U) -#define HCINTMSK_XFRCM_Msk (0x1UL << HCINTMSK_XFRCM_Pos) // 0x00000001 */ -#define HCINTMSK_XFRCM HCINTMSK_XFRCM_Msk // Transfer completed mask */ +#define HCINTMSK_XFRCM_Msk (0x1UL << HCINTMSK_XFRCM_Pos) // 0x00000001 +#define HCINTMSK_XFRCM HCINTMSK_XFRCM_Msk // Transfer completed mask #define HCINTMSK_CHHM_Pos (1U) -#define HCINTMSK_CHHM_Msk (0x1UL << HCINTMSK_CHHM_Pos) // 0x00000002 */ -#define HCINTMSK_CHHM HCINTMSK_CHHM_Msk // Channel halted mask */ +#define HCINTMSK_CHHM_Msk (0x1UL << HCINTMSK_CHHM_Pos) // 0x00000002 +#define HCINTMSK_CHHM HCINTMSK_CHHM_Msk // Channel halted mask #define HCINTMSK_AHBERR_Pos (2U) -#define HCINTMSK_AHBERR_Msk (0x1UL << HCINTMSK_AHBERR_Pos) // 0x00000004 */ -#define HCINTMSK_AHBERR HCINTMSK_AHBERR_Msk // AHB error */ +#define HCINTMSK_AHBERR_Msk (0x1UL << HCINTMSK_AHBERR_Pos) // 0x00000004 +#define HCINTMSK_AHBERR HCINTMSK_AHBERR_Msk // AHB error #define HCINTMSK_STALLM_Pos (3U) -#define HCINTMSK_STALLM_Msk (0x1UL << HCINTMSK_STALLM_Pos) // 0x00000008 */ -#define HCINTMSK_STALLM HCINTMSK_STALLM_Msk // STALL response received interrupt mask */ +#define HCINTMSK_STALLM_Msk (0x1UL << HCINTMSK_STALLM_Pos) // 0x00000008 +#define HCINTMSK_STALLM HCINTMSK_STALLM_Msk // STALL response received interrupt mask #define HCINTMSK_NAKM_Pos (4U) -#define HCINTMSK_NAKM_Msk (0x1UL << HCINTMSK_NAKM_Pos) // 0x00000010 */ -#define HCINTMSK_NAKM HCINTMSK_NAKM_Msk // NAK response received interrupt mask */ +#define HCINTMSK_NAKM_Msk (0x1UL << HCINTMSK_NAKM_Pos) // 0x00000010 +#define HCINTMSK_NAKM HCINTMSK_NAKM_Msk // NAK response received interrupt mask #define HCINTMSK_ACKM_Pos (5U) -#define HCINTMSK_ACKM_Msk (0x1UL << HCINTMSK_ACKM_Pos) // 0x00000020 */ -#define HCINTMSK_ACKM HCINTMSK_ACKM_Msk // ACK response received/transmitted interrupt mask */ +#define HCINTMSK_ACKM_Msk (0x1UL << HCINTMSK_ACKM_Pos) // 0x00000020 +#define HCINTMSK_ACKM HCINTMSK_ACKM_Msk // ACK response received/transmitted interrupt mask #define HCINTMSK_NYET_Pos (6U) -#define HCINTMSK_NYET_Msk (0x1UL << HCINTMSK_NYET_Pos) // 0x00000040 */ -#define HCINTMSK_NYET HCINTMSK_NYET_Msk // response received interrupt mask */ +#define HCINTMSK_NYET_Msk (0x1UL << HCINTMSK_NYET_Pos) // 0x00000040 +#define HCINTMSK_NYET HCINTMSK_NYET_Msk // response received interrupt mask #define HCINTMSK_TXERRM_Pos (7U) -#define HCINTMSK_TXERRM_Msk (0x1UL << HCINTMSK_TXERRM_Pos) // 0x00000080 */ -#define HCINTMSK_TXERRM HCINTMSK_TXERRM_Msk // Transaction error mask */ +#define HCINTMSK_TXERRM_Msk (0x1UL << HCINTMSK_TXERRM_Pos) // 0x00000080 +#define HCINTMSK_TXERRM HCINTMSK_TXERRM_Msk // Transaction error mask #define HCINTMSK_BBERRM_Pos (8U) -#define HCINTMSK_BBERRM_Msk (0x1UL << HCINTMSK_BBERRM_Pos) // 0x00000100 */ -#define HCINTMSK_BBERRM HCINTMSK_BBERRM_Msk // Babble error mask */ +#define HCINTMSK_BBERRM_Msk (0x1UL << HCINTMSK_BBERRM_Pos) // 0x00000100 +#define HCINTMSK_BBERRM HCINTMSK_BBERRM_Msk // Babble error mask #define HCINTMSK_FRMORM_Pos (9U) -#define HCINTMSK_FRMORM_Msk (0x1UL << HCINTMSK_FRMORM_Pos) // 0x00000200 */ -#define HCINTMSK_FRMORM HCINTMSK_FRMORM_Msk // Frame overrun mask */ +#define HCINTMSK_FRMORM_Msk (0x1UL << HCINTMSK_FRMORM_Pos) // 0x00000200 +#define HCINTMSK_FRMORM HCINTMSK_FRMORM_Msk // Frame overrun mask #define HCINTMSK_DTERRM_Pos (10U) -#define HCINTMSK_DTERRM_Msk (0x1UL << HCINTMSK_DTERRM_Pos) // 0x00000400 */ -#define HCINTMSK_DTERRM HCINTMSK_DTERRM_Msk // Data toggle error mask */ +#define HCINTMSK_DTERRM_Msk (0x1UL << HCINTMSK_DTERRM_Pos) // 0x00000400 +#define HCINTMSK_DTERRM HCINTMSK_DTERRM_Msk // Data toggle error mask /******************** Bit definition for DIEPTSIZ register ********************/ #define DIEPTSIZ_XFRSIZ_Pos (0U) -#define DIEPTSIZ_XFRSIZ_Msk (0x7FFFFUL << DIEPTSIZ_XFRSIZ_Pos) // 0x0007FFFF */ -#define DIEPTSIZ_XFRSIZ DIEPTSIZ_XFRSIZ_Msk // Transfer size */ +#define DIEPTSIZ_XFRSIZ_Msk (0x7FFFFUL << DIEPTSIZ_XFRSIZ_Pos) // 0x0007FFFF +#define DIEPTSIZ_XFRSIZ DIEPTSIZ_XFRSIZ_Msk // Transfer size #define DIEPTSIZ_PKTCNT_Pos (19U) -#define DIEPTSIZ_PKTCNT_Msk (0x3FFUL << DIEPTSIZ_PKTCNT_Pos) // 0x1FF80000 */ -#define DIEPTSIZ_PKTCNT DIEPTSIZ_PKTCNT_Msk // Packet count */ +#define DIEPTSIZ_PKTCNT_Msk (0x3FFUL << DIEPTSIZ_PKTCNT_Pos) // 0x1FF80000 +#define DIEPTSIZ_PKTCNT DIEPTSIZ_PKTCNT_Msk // Packet count #define DIEPTSIZ_MULCNT_Pos (29U) -#define DIEPTSIZ_MULCNT_Msk (0x3UL << DIEPTSIZ_MULCNT_Pos) // 0x60000000 */ -#define DIEPTSIZ_MULCNT DIEPTSIZ_MULCNT_Msk // Packet count */ +#define DIEPTSIZ_MULCNT_Msk (0x3UL << DIEPTSIZ_MULCNT_Pos) // 0x60000000 +#define DIEPTSIZ_MULCNT DIEPTSIZ_MULCNT_Msk // Packet count /******************** Bit definition for HCTSIZ register ********************/ #define HCTSIZ_XFRSIZ_Pos (0U) -#define HCTSIZ_XFRSIZ_Msk (0x7FFFFUL << HCTSIZ_XFRSIZ_Pos) // 0x0007FFFF */ -#define HCTSIZ_XFRSIZ HCTSIZ_XFRSIZ_Msk // Transfer size */ +#define HCTSIZ_XFRSIZ_Msk (0x7FFFFUL << HCTSIZ_XFRSIZ_Pos) // 0x0007FFFF +#define HCTSIZ_XFRSIZ HCTSIZ_XFRSIZ_Msk // Transfer size #define HCTSIZ_PKTCNT_Pos (19U) -#define HCTSIZ_PKTCNT_Msk (0x3FFUL << HCTSIZ_PKTCNT_Pos) // 0x1FF80000 */ -#define HCTSIZ_PKTCNT HCTSIZ_PKTCNT_Msk // Packet count */ +#define HCTSIZ_PKTCNT_Msk (0x3FFUL << HCTSIZ_PKTCNT_Pos) // 0x1FF80000 +#define HCTSIZ_PKTCNT HCTSIZ_PKTCNT_Msk // Packet count #define HCTSIZ_DOPING_Pos (31U) -#define HCTSIZ_DOPING_Msk (0x1UL << HCTSIZ_DOPING_Pos) // 0x80000000 */ -#define HCTSIZ_DOPING HCTSIZ_DOPING_Msk // Do PING */ +#define HCTSIZ_DOPING_Msk (0x1UL << HCTSIZ_DOPING_Pos) // 0x80000000 +#define HCTSIZ_DOPING HCTSIZ_DOPING_Msk // Do PING #define HCTSIZ_DPID_Pos (29U) -#define HCTSIZ_DPID_Msk (0x3UL << HCTSIZ_DPID_Pos) // 0x60000000 */ -#define HCTSIZ_DPID HCTSIZ_DPID_Msk // Data PID */ -#define HCTSIZ_DPID_0 (0x1UL << HCTSIZ_DPID_Pos) // 0x20000000 */ -#define HCTSIZ_DPID_1 (0x2UL << HCTSIZ_DPID_Pos) // 0x40000000 */ +#define HCTSIZ_DPID_Msk (0x3UL << HCTSIZ_DPID_Pos) // 0x60000000 +#define HCTSIZ_DPID HCTSIZ_DPID_Msk // Data PID +#define HCTSIZ_DPID_0 (0x1UL << HCTSIZ_DPID_Pos) // 0x20000000 +#define HCTSIZ_DPID_1 (0x2UL << HCTSIZ_DPID_Pos) // 0x40000000 /******************** Bit definition for DIEPDMA register ********************/ #define DIEPDMA_DMAADDR_Pos (0U) -#define DIEPDMA_DMAADDR_Msk (0xFFFFFFFFUL << DIEPDMA_DMAADDR_Pos) // 0xFFFFFFFF */ -#define DIEPDMA_DMAADDR DIEPDMA_DMAADDR_Msk // DMA address */ +#define DIEPDMA_DMAADDR_Msk (0xFFFFFFFFUL << DIEPDMA_DMAADDR_Pos) // 0xFFFFFFFF +#define DIEPDMA_DMAADDR DIEPDMA_DMAADDR_Msk // DMA address /******************** Bit definition for HCDMA register ********************/ #define HCDMA_DMAADDR_Pos (0U) -#define HCDMA_DMAADDR_Msk (0xFFFFFFFFUL << HCDMA_DMAADDR_Pos) // 0xFFFFFFFF */ -#define HCDMA_DMAADDR HCDMA_DMAADDR_Msk // DMA address */ +#define HCDMA_DMAADDR_Msk (0xFFFFFFFFUL << HCDMA_DMAADDR_Pos) // 0xFFFFFFFF +#define HCDMA_DMAADDR HCDMA_DMAADDR_Msk // DMA address /******************** Bit definition for DTXFSTS register ********************/ #define DTXFSTS_INEPTFSAV_Pos (0U) -#define DTXFSTS_INEPTFSAV_Msk (0xFFFFUL << DTXFSTS_INEPTFSAV_Pos) // 0x0000FFFF */ -#define DTXFSTS_INEPTFSAV DTXFSTS_INEPTFSAV_Msk // IN endpoint TxFIFO space available */ +#define DTXFSTS_INEPTFSAV_Msk (0xFFFFUL << DTXFSTS_INEPTFSAV_Pos) // 0x0000FFFF +#define DTXFSTS_INEPTFSAV DTXFSTS_INEPTFSAV_Msk // IN endpoint TxFIFO space available /******************** Bit definition for DIEPTXF register ********************/ #define DIEPTXF_INEPTXSA_Pos (0U) -#define DIEPTXF_INEPTXSA_Msk (0xFFFFUL << DIEPTXF_INEPTXSA_Pos) // 0x0000FFFF */ -#define DIEPTXF_INEPTXSA DIEPTXF_INEPTXSA_Msk // IN endpoint FIFOx transmit RAM start address */ +#define DIEPTXF_INEPTXSA_Msk (0xFFFFUL << DIEPTXF_INEPTXSA_Pos) // 0x0000FFFF +#define DIEPTXF_INEPTXSA DIEPTXF_INEPTXSA_Msk // IN endpoint FIFOx transmit RAM start address #define DIEPTXF_INEPTXFD_Pos (16U) -#define DIEPTXF_INEPTXFD_Msk (0xFFFFUL << DIEPTXF_INEPTXFD_Pos) // 0xFFFF0000 */ -#define DIEPTXF_INEPTXFD DIEPTXF_INEPTXFD_Msk // IN endpoint TxFIFO depth */ +#define DIEPTXF_INEPTXFD_Msk (0xFFFFUL << DIEPTXF_INEPTXFD_Pos) // 0xFFFF0000 +#define DIEPTXF_INEPTXFD DIEPTXF_INEPTXFD_Msk // IN endpoint TxFIFO depth /******************** Bit definition for DOEPCTL register ********************/ #define DOEPCTL_MPSIZ_Pos (0U) -#define DOEPCTL_MPSIZ_Msk (0x7FFUL << DOEPCTL_MPSIZ_Pos) // 0x000007FF */ -#define DOEPCTL_MPSIZ DOEPCTL_MPSIZ_Msk // Maximum packet size */ //Bit 1 */ +#define DOEPCTL_MPSIZ_Msk (0x7FFUL << DOEPCTL_MPSIZ_Pos) // 0x000007FF +#define DOEPCTL_MPSIZ DOEPCTL_MPSIZ_Msk // Maximum packet size //Bit 1 #define DOEPCTL_USBAEP_Pos (15U) -#define DOEPCTL_USBAEP_Msk (0x1UL << DOEPCTL_USBAEP_Pos) // 0x00008000 */ -#define DOEPCTL_USBAEP DOEPCTL_USBAEP_Msk // USB active endpoint */ +#define DOEPCTL_USBAEP_Msk (0x1UL << DOEPCTL_USBAEP_Pos) // 0x00008000 +#define DOEPCTL_USBAEP DOEPCTL_USBAEP_Msk // USB active endpoint #define DOEPCTL_NAKSTS_Pos (17U) -#define DOEPCTL_NAKSTS_Msk (0x1UL << DOEPCTL_NAKSTS_Pos) // 0x00020000 */ -#define DOEPCTL_NAKSTS DOEPCTL_NAKSTS_Msk // NAK status */ +#define DOEPCTL_NAKSTS_Msk (0x1UL << DOEPCTL_NAKSTS_Pos) // 0x00020000 +#define DOEPCTL_NAKSTS DOEPCTL_NAKSTS_Msk // NAK status #define DOEPCTL_SD0PID_SEVNFRM_Pos (28U) -#define DOEPCTL_SD0PID_SEVNFRM_Msk (0x1UL << DOEPCTL_SD0PID_SEVNFRM_Pos) // 0x10000000 */ -#define DOEPCTL_SD0PID_SEVNFRM DOEPCTL_SD0PID_SEVNFRM_Msk // Set DATA0 PID */ +#define DOEPCTL_SD0PID_SEVNFRM_Msk (0x1UL << DOEPCTL_SD0PID_SEVNFRM_Pos) // 0x10000000 +#define DOEPCTL_SD0PID_SEVNFRM DOEPCTL_SD0PID_SEVNFRM_Msk // Set DATA0 PID #define DOEPCTL_SODDFRM_Pos (29U) -#define DOEPCTL_SODDFRM_Msk (0x1UL << DOEPCTL_SODDFRM_Pos) // 0x20000000 */ -#define DOEPCTL_SODDFRM DOEPCTL_SODDFRM_Msk // Set odd frame */ +#define DOEPCTL_SODDFRM_Msk (0x1UL << DOEPCTL_SODDFRM_Pos) // 0x20000000 +#define DOEPCTL_SODDFRM DOEPCTL_SODDFRM_Msk // Set odd frame #define DOEPCTL_EPTYP_Pos (18U) -#define DOEPCTL_EPTYP_Msk (0x3UL << DOEPCTL_EPTYP_Pos) // 0x000C0000 */ -#define DOEPCTL_EPTYP DOEPCTL_EPTYP_Msk // Endpoint type */ -#define DOEPCTL_EPTYP_0 (0x1UL << DOEPCTL_EPTYP_Pos) // 0x00040000 */ -#define DOEPCTL_EPTYP_1 (0x2UL << DOEPCTL_EPTYP_Pos) // 0x00080000 */ +#define DOEPCTL_EPTYP_Msk (0x3UL << DOEPCTL_EPTYP_Pos) // 0x000C0000 +#define DOEPCTL_EPTYP DOEPCTL_EPTYP_Msk // Endpoint type +#define DOEPCTL_EPTYP_0 (0x1UL << DOEPCTL_EPTYP_Pos) // 0x00040000 +#define DOEPCTL_EPTYP_1 (0x2UL << DOEPCTL_EPTYP_Pos) // 0x00080000 #define DOEPCTL_SNPM_Pos (20U) -#define DOEPCTL_SNPM_Msk (0x1UL << DOEPCTL_SNPM_Pos) // 0x00100000 */ -#define DOEPCTL_SNPM DOEPCTL_SNPM_Msk // Snoop mode */ +#define DOEPCTL_SNPM_Msk (0x1UL << DOEPCTL_SNPM_Pos) // 0x00100000 +#define DOEPCTL_SNPM DOEPCTL_SNPM_Msk // Snoop mode #define DOEPCTL_STALL_Pos (21U) -#define DOEPCTL_STALL_Msk (0x1UL << DOEPCTL_STALL_Pos) // 0x00200000 */ -#define DOEPCTL_STALL DOEPCTL_STALL_Msk // STALL handshake */ +#define DOEPCTL_STALL_Msk (0x1UL << DOEPCTL_STALL_Pos) // 0x00200000 +#define DOEPCTL_STALL DOEPCTL_STALL_Msk // STALL handshake #define DOEPCTL_CNAK_Pos (26U) -#define DOEPCTL_CNAK_Msk (0x1UL << DOEPCTL_CNAK_Pos) // 0x04000000 */ -#define DOEPCTL_CNAK DOEPCTL_CNAK_Msk // Clear NAK */ +#define DOEPCTL_CNAK_Msk (0x1UL << DOEPCTL_CNAK_Pos) // 0x04000000 +#define DOEPCTL_CNAK DOEPCTL_CNAK_Msk // Clear NAK #define DOEPCTL_SNAK_Pos (27U) -#define DOEPCTL_SNAK_Msk (0x1UL << DOEPCTL_SNAK_Pos) // 0x08000000 */ -#define DOEPCTL_SNAK DOEPCTL_SNAK_Msk // Set NAK */ +#define DOEPCTL_SNAK_Msk (0x1UL << DOEPCTL_SNAK_Pos) // 0x08000000 +#define DOEPCTL_SNAK DOEPCTL_SNAK_Msk // Set NAK #define DOEPCTL_EPDIS_Pos (30U) -#define DOEPCTL_EPDIS_Msk (0x1UL << DOEPCTL_EPDIS_Pos) // 0x40000000 */ -#define DOEPCTL_EPDIS DOEPCTL_EPDIS_Msk // Endpoint disable */ +#define DOEPCTL_EPDIS_Msk (0x1UL << DOEPCTL_EPDIS_Pos) // 0x40000000 +#define DOEPCTL_EPDIS DOEPCTL_EPDIS_Msk // Endpoint disable #define DOEPCTL_EPENA_Pos (31U) -#define DOEPCTL_EPENA_Msk (0x1UL << DOEPCTL_EPENA_Pos) // 0x80000000 */ -#define DOEPCTL_EPENA DOEPCTL_EPENA_Msk // Endpoint enable */ +#define DOEPCTL_EPENA_Msk (0x1UL << DOEPCTL_EPENA_Pos) // 0x80000000 +#define DOEPCTL_EPENA DOEPCTL_EPENA_Msk // Endpoint enable /******************** Bit definition for DOEPINT register ********************/ #define DOEPINT_XFRC_Pos (0U) -#define DOEPINT_XFRC_Msk (0x1UL << DOEPINT_XFRC_Pos) // 0x00000001 */ -#define DOEPINT_XFRC DOEPINT_XFRC_Msk // Transfer completed interrupt */ +#define DOEPINT_XFRC_Msk (0x1UL << DOEPINT_XFRC_Pos) // 0x00000001 +#define DOEPINT_XFRC DOEPINT_XFRC_Msk // Transfer completed interrupt #define DOEPINT_EPDISD_Pos (1U) -#define DOEPINT_EPDISD_Msk (0x1UL << DOEPINT_EPDISD_Pos) // 0x00000002 */ -#define DOEPINT_EPDISD DOEPINT_EPDISD_Msk // Endpoint disabled interrupt */ +#define DOEPINT_EPDISD_Msk (0x1UL << DOEPINT_EPDISD_Pos) // 0x00000002 +#define DOEPINT_EPDISD DOEPINT_EPDISD_Msk // Endpoint disabled interrupt #define DOEPINT_AHBERR_Pos (2U) -#define DOEPINT_AHBERR_Msk (0x1UL << DOEPINT_AHBERR_Pos) // 0x00000004 */ -#define DOEPINT_AHBERR DOEPINT_AHBERR_Msk // AHB Error (AHBErr) during an OUT transaction */ +#define DOEPINT_AHBERR_Msk (0x1UL << DOEPINT_AHBERR_Pos) // 0x00000004 +#define DOEPINT_AHBERR DOEPINT_AHBERR_Msk // AHB Error (AHBErr) during an OUT transaction #define DOEPINT_STUP_Pos (3U) -#define DOEPINT_STUP_Msk (0x1UL << DOEPINT_STUP_Pos) // 0x00000008 */ -#define DOEPINT_STUP DOEPINT_STUP_Msk // SETUP phase done */ +#define DOEPINT_STUP_Msk (0x1UL << DOEPINT_STUP_Pos) // 0x00000008 +#define DOEPINT_STUP DOEPINT_STUP_Msk // SETUP phase done #define DOEPINT_OTEPDIS_Pos (4U) -#define DOEPINT_OTEPDIS_Msk (0x1UL << DOEPINT_OTEPDIS_Pos) // 0x00000010 */ -#define DOEPINT_OTEPDIS DOEPINT_OTEPDIS_Msk // OUT token received when endpoint disabled */ +#define DOEPINT_OTEPDIS_Msk (0x1UL << DOEPINT_OTEPDIS_Pos) // 0x00000010 +#define DOEPINT_OTEPDIS DOEPINT_OTEPDIS_Msk // OUT token received when endpoint disabled #define DOEPINT_OTEPSPR_Pos (5U) -#define DOEPINT_OTEPSPR_Msk (0x1UL << DOEPINT_OTEPSPR_Pos) // 0x00000020 */ -#define DOEPINT_OTEPSPR DOEPINT_OTEPSPR_Msk // Status Phase Received For Control Write */ +#define DOEPINT_OTEPSPR_Msk (0x1UL << DOEPINT_OTEPSPR_Pos) // 0x00000020 +#define DOEPINT_OTEPSPR DOEPINT_OTEPSPR_Msk // Status Phase Received For Control Write #define DOEPINT_B2BSTUP_Pos (6U) -#define DOEPINT_B2BSTUP_Msk (0x1UL << DOEPINT_B2BSTUP_Pos) // 0x00000040 */ -#define DOEPINT_B2BSTUP DOEPINT_B2BSTUP_Msk // Back-to-back SETUP packets received */ +#define DOEPINT_B2BSTUP_Msk (0x1UL << DOEPINT_B2BSTUP_Pos) // 0x00000040 +#define DOEPINT_B2BSTUP DOEPINT_B2BSTUP_Msk // Back-to-back SETUP packets received #define DOEPINT_OUTPKTERR_Pos (8U) -#define DOEPINT_OUTPKTERR_Msk (0x1UL << DOEPINT_OUTPKTERR_Pos) // 0x00000100 */ -#define DOEPINT_OUTPKTERR DOEPINT_OUTPKTERR_Msk // OUT packet error */ +#define DOEPINT_OUTPKTERR_Msk (0x1UL << DOEPINT_OUTPKTERR_Pos) // 0x00000100 +#define DOEPINT_OUTPKTERR DOEPINT_OUTPKTERR_Msk // OUT packet error #define DOEPINT_NAK_Pos (13U) -#define DOEPINT_NAK_Msk (0x1UL << DOEPINT_NAK_Pos) // 0x00002000 */ -#define DOEPINT_NAK DOEPINT_NAK_Msk // NAK Packet is transmitted by the device */ +#define DOEPINT_NAK_Msk (0x1UL << DOEPINT_NAK_Pos) // 0x00002000 +#define DOEPINT_NAK DOEPINT_NAK_Msk // NAK Packet is transmitted by the device #define DOEPINT_NYET_Pos (14U) -#define DOEPINT_NYET_Msk (0x1UL << DOEPINT_NYET_Pos) // 0x00004000 */ -#define DOEPINT_NYET DOEPINT_NYET_Msk // NYET interrupt */ +#define DOEPINT_NYET_Msk (0x1UL << DOEPINT_NYET_Pos) // 0x00004000 +#define DOEPINT_NYET DOEPINT_NYET_Msk // NYET interrupt #define DOEPINT_STPKTRX_Pos (15U) -#define DOEPINT_STPKTRX_Msk (0x1UL << DOEPINT_STPKTRX_Pos) // 0x00008000 */ -#define DOEPINT_STPKTRX DOEPINT_STPKTRX_Msk // Setup Packet Received */ +#define DOEPINT_STPKTRX_Msk (0x1UL << DOEPINT_STPKTRX_Pos) // 0x00008000 +#define DOEPINT_STPKTRX DOEPINT_STPKTRX_Msk // Setup Packet Received /******************** Bit definition for DOEPTSIZ register ********************/ #define DOEPTSIZ_XFRSIZ_Pos (0U) -#define DOEPTSIZ_XFRSIZ_Msk (0x7FFFFUL << DOEPTSIZ_XFRSIZ_Pos) // 0x0007FFFF */ -#define DOEPTSIZ_XFRSIZ DOEPTSIZ_XFRSIZ_Msk // Transfer size */ +#define DOEPTSIZ_XFRSIZ_Msk (0x7FFFFUL << DOEPTSIZ_XFRSIZ_Pos) // 0x0007FFFF +#define DOEPTSIZ_XFRSIZ DOEPTSIZ_XFRSIZ_Msk // Transfer size #define DOEPTSIZ_PKTCNT_Pos (19U) -#define DOEPTSIZ_PKTCNT_Msk (0x3FFUL << DOEPTSIZ_PKTCNT_Pos) // 0x1FF80000 */ -#define DOEPTSIZ_PKTCNT DOEPTSIZ_PKTCNT_Msk // Packet count */ +#define DOEPTSIZ_PKTCNT_Msk (0x3FFUL << DOEPTSIZ_PKTCNT_Pos) // 0x1FF80000 +#define DOEPTSIZ_PKTCNT DOEPTSIZ_PKTCNT_Msk // Packet count #define DOEPTSIZ_STUPCNT_Pos (29U) -#define DOEPTSIZ_STUPCNT_Msk (0x3UL << DOEPTSIZ_STUPCNT_Pos) // 0x60000000 */ -#define DOEPTSIZ_STUPCNT DOEPTSIZ_STUPCNT_Msk // SETUP packet count */ -#define DOEPTSIZ_STUPCNT_0 (0x1UL << DOEPTSIZ_STUPCNT_Pos) // 0x20000000 */ -#define DOEPTSIZ_STUPCNT_1 (0x2UL << DOEPTSIZ_STUPCNT_Pos) // 0x40000000 */ +#define DOEPTSIZ_STUPCNT_Msk (0x3UL << DOEPTSIZ_STUPCNT_Pos) // 0x60000000 +#define DOEPTSIZ_STUPCNT DOEPTSIZ_STUPCNT_Msk // SETUP packet count +#define DOEPTSIZ_STUPCNT_0 (0x1UL << DOEPTSIZ_STUPCNT_Pos) // 0x20000000 +#define DOEPTSIZ_STUPCNT_1 (0x2UL << DOEPTSIZ_STUPCNT_Pos) // 0x40000000 /******************** Bit definition for PCGCTL register ********************/ #define PCGCTL_IF_DEV_MODE TU_BIT(31) -- cgit v1.3.1 From db3ff4b3527b9b81d381ecc21a74e76e81b2a8e9 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 31 Oct 2023 11:26:31 +0700 Subject: usb on u5a5 hs work well with correct VBVALEXTOEN/VBVALOVAL set --- hw/bsp/family_support.cmake | 2 +- hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake | 1 + hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h | 6 +++-- hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk | 1 + hw/bsp/stm32u5/family.c | 28 +++++++++++------------ src/portable/synopsys/dwc2/dcd_dwc2.c | 3 ++- src/portable/synopsys/dwc2/dwc2_stm32.h | 25 +++++++++++--------- 7 files changed, 37 insertions(+), 29 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index 9c625b58e..eec42160e 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -217,7 +217,7 @@ function(family_configure_common TARGET RTOS) if (NOT TARGET segger_rtt) add_library(segger_rtt STATIC ${TOP}/lib/SEGGER_RTT/RTT/SEGGER_RTT.c) target_include_directories(segger_rtt PUBLIC ${TOP}/lib/SEGGER_RTT/RTT) - target_compile_definitions(segger_rtt PUBLIC SEGGER_RTT_MODE_DEFAULT=SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL) + #target_compile_definitions(segger_rtt PUBLIC SEGGER_RTT_MODE_DEFAULT=SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL) endif() target_link_libraries(${TARGET} PUBLIC segger_rtt) endif () diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake index 24d4ef95a..230c3b722 100644 --- a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake +++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.cmake @@ -6,5 +6,6 @@ set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32U5A5ZJTXQ_FLASH.ld) function(update_board TARGET) target_compile_definitions(${TARGET} PUBLIC STM32U5A5xx + HSE_VALUE=16000000UL ) endfunction() diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h index c4eb94dd8..1cc61d6bb 100644 --- a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h +++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.h @@ -38,8 +38,8 @@ extern "C" #define LED_STATE_ON 1 // BUTTON -#define BUTTON_PORT GPIOA -#define BUTTON_PIN GPIO_PIN_0 +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 #define BUTTON_STATE_ACTIVE 1 // UART Enable for STLink VCOM @@ -101,6 +101,8 @@ static void SystemClock_Config(void) { HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4); // USB Clock + __HAL_RCC_SYSCFG_CLK_ENABLE(); + RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USBPHY; PeriphClkInit.UsbPhyClockSelection = RCC_USBPHYCLKSOURCE_HSE; diff --git a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk index 13025efa6..e759cec24 100644 --- a/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk +++ b/hw/bsp/stm32u5/boards/stm32u5a5nucleo/board.mk @@ -1,5 +1,6 @@ CFLAGS += \ -DSTM32U5A5xx \ + -DHSE_VALUE=16000000UL \ # All source paths should be relative to the top level. LD_FILE = ${BOARD_PATH}/STM32U5A5ZJTXQ_FLASH.ld diff --git a/hw/bsp/stm32u5/family.c b/hw/bsp/stm32u5/family.c index 3fbc50d93..94294b25d 100644 --- a/hw/bsp/stm32u5/family.c +++ b/hw/bsp/stm32u5/family.c @@ -124,7 +124,7 @@ void board_init(void) { HAL_UART_Init(&UartHandle); - /* Configure USB FS GPIOs */ + /* Configure USB GPIOs */ /* Configure DM DP Pins */ GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; @@ -153,6 +153,12 @@ void board_init(void) { GPIO_InitStruct.Pull = GPIO_NOPULL; HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + /* Enable USB power on Pwrctrl CR2 register */ + HAL_PWREx_EnableVddUSB(); + + /* USB clock enable */ + __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); + // Enable VBUS sense (B device) via pin PA9 USB_OTG_FS->GCCFG |= USB_OTG_GCCFG_VBDEN; #else @@ -164,11 +170,6 @@ void board_init(void) { USB_OTG_FS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; #endif // vbus sense - /* Enable USB power on Pwrctrl CR2 register */ - HAL_PWREx_EnableVddUSB(); - - /* USB clock enable */ - __HAL_RCC_USB_OTG_FS_CLK_ENABLE(); #else // STM59x/Ax/Fx/Gx only have 1 USB HS port @@ -177,15 +178,7 @@ void board_init(void) { NVIC_SetPriority(OTG_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); #endif - // Disable VBUS sense (B device) - USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; - - // B-peripheral session valid override enable - USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN; - USB_OTG_HS->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL; - /* USB clock enable */ - __HAL_RCC_SYSCFG_CLK_ENABLE(); __HAL_RCC_USB_OTG_HS_CLK_ENABLE(); __HAL_RCC_USBPHYC_CLK_ENABLE(); @@ -195,6 +188,13 @@ void board_init(void) { /*Configuring the SYSCFG registers OTG_HS PHY*/ HAL_SYSCFG_EnableOTGPHY(SYSCFG_OTG_HS_PHY_ENABLE); + + // Disable VBUS sense (B device) + USB_OTG_HS->GCCFG &= ~USB_OTG_GCCFG_VBDEN; + + // B-peripheral session valid override enable + USB_OTG_HS->GCCFG |= USB_OTG_GCCFG_VBVALEXTOEN; + USB_OTG_HS->GCCFG |= USB_OTG_GCCFG_VBVALOVAL; #endif // USB_OTG_FS diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index 7b50a7d54..5c5450ac2 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -1074,7 +1074,6 @@ void dcd_int_handler(uint8_t rhport) { if (int_status & GINTSTS_ENUMDNE) { // ENUMDNE is the end of reset where speed of the link is detected - dwc2->gintsts = GINTSTS_ENUMDNE; tusb_speed_t speed; @@ -1094,6 +1093,8 @@ void dcd_int_handler(uint8_t rhport) { break; } + // TODO must update GUSBCFG_TRDT according to link speed + dcd_event_bus_reset(rhport, speed, true); } diff --git a/src/portable/synopsys/dwc2/dwc2_stm32.h b/src/portable/synopsys/dwc2/dwc2_stm32.h index 57df4e941..2070c3943 100644 --- a/src/portable/synopsys/dwc2/dwc2_stm32.h +++ b/src/portable/synopsys/dwc2/dwc2_stm32.h @@ -24,8 +24,8 @@ * This file is part of the TinyUSB stack. */ -#ifndef _DWC2_STM32_H_ -#define _DWC2_STM32_H_ +#ifndef DWC2_STM32_H_ +#define DWC2_STM32_H_ #ifdef __cplusplus extern "C" { @@ -124,35 +124,36 @@ static const dwc2_controller_t _dwc2_controller[] = { // SystemCoreClock is already included by family header // extern uint32_t SystemCoreClock; -TU_ATTR_ALWAYS_INLINE -static inline void dwc2_dcd_int_enable(uint8_t rhport) { +TU_ATTR_ALWAYS_INLINE static inline void dwc2_dcd_int_enable(uint8_t rhport) { NVIC_EnableIRQ((IRQn_Type) _dwc2_controller[rhport].irqnum); } -TU_ATTR_ALWAYS_INLINE -static inline void dwc2_dcd_int_disable(uint8_t rhport) { +TU_ATTR_ALWAYS_INLINE static inline void dwc2_dcd_int_disable(uint8_t rhport) { NVIC_DisableIRQ((IRQn_Type) _dwc2_controller[rhport].irqnum); } -TU_ATTR_ALWAYS_INLINE -static inline void dwc2_remote_wakeup_delay(void) { +TU_ATTR_ALWAYS_INLINE static inline void dwc2_remote_wakeup_delay(void) { // try to delay for 1 ms uint32_t count = SystemCoreClock / 1000; while (count--) __NOP(); } // MCU specific PHY init, called BEFORE core reset +// - dwc2 3.30a (H5) use USB_HS_PHYC +// - dwc2 4.11a (U5) use femtoPHY static inline void dwc2_phy_init(dwc2_regs_t* dwc2, uint8_t hs_phy_type) { if (hs_phy_type == HS_PHY_TYPE_NONE) { // Enable on-chip FS PHY dwc2->stm32_gccfg |= STM32_GCCFG_PWRDWN; } else { +#if CFG_TUSB_MCU != OPT_MCU_STM32U5 // Disable FS PHY, TODO on U5A5 (dwc2 4.11a) 16th bit is 'Host CDP behavior enable' dwc2->stm32_gccfg &= ~STM32_GCCFG_PWRDWN; +#endif // Enable on-chip HS PHY if (hs_phy_type == HS_PHY_TYPE_UTMI || hs_phy_type == HS_PHY_TYPE_UTMI_ULPI) { -#ifdef USB_HS_PHYC + #ifdef USB_HS_PHYC // Enable UTMI HS PHY dwc2->stm32_gccfg |= STM32_GCCFG_PHYHSEN; @@ -184,7 +185,9 @@ static inline void dwc2_phy_init(dwc2_regs_t* dwc2, uint8_t hs_phy_type) { // Enable PLL internal PHY USB_HS_PHYC->USB_HS_PHYC_PLL |= USB_HS_PHYC_PLL_PLLEN; -#endif + #else + + #endif } } } @@ -232,4 +235,4 @@ static inline void dwc2_phy_update(dwc2_regs_t* dwc2, uint8_t hs_phy_type) { } #endif -#endif /* _DWC2_STM32_H_ */ +#endif -- cgit v1.3.1 From 214a4afa6aafe9daac6c1c304eb305b44e8cf86d Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 31 Oct 2023 11:53:40 +0700 Subject: dwc2 flush tx,rx fifo in dcd_init() --- src/portable/synopsys/dwc2/dcd_dwc2.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index 5c5450ac2..ac93632be 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -447,6 +447,14 @@ void dcd_init(uint8_t rhport) { // (non zero-length packet), send STALL back and discard. dwc2->dcfg |= DCFG_NZLSOHSK; + // flush all TX fifo and wait for it cleared + dwc2->grstctl = GRSTCTL_TXFFLSH | (0x10u << GRSTCTL_TXFNUM_Pos); + while (dwc2->grstctl & GRSTCTL_TXFFLSH_Msk) {} + + // flush RX fifo and wait for it cleared + dwc2->grstctl = GRSTCTL_RXFFLSH; + while (dwc2->grstctl & GRSTCTL_RXFFLSH_Msk) {} + // Clear all interrupts uint32_t int_mask = dwc2->gintsts; dwc2->gintsts |= int_mask; -- cgit v1.3.1 From 06c9d9a79a4426ece73052edca885f890b997fc4 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 1 Nov 2023 16:36:28 +0700 Subject: remove legacy driver st/synopsys --- src/portable/st/synopsys/dcd_synopsys.c | 1240 ----------------------- src/portable/st/synopsys/synopsys_common.h | 1465 ---------------------------- 2 files changed, 2705 deletions(-) delete mode 100644 src/portable/st/synopsys/dcd_synopsys.c delete mode 100644 src/portable/st/synopsys/synopsys_common.h (limited to 'src/portable') diff --git a/src/portable/st/synopsys/dcd_synopsys.c b/src/portable/st/synopsys/dcd_synopsys.c deleted file mode 100644 index 2fc3adb4f..000000000 --- a/src/portable/st/synopsys/dcd_synopsys.c +++ /dev/null @@ -1,1240 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2018 Scott Shawcroft, 2019 William D. Jones for Adafruit Industries - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * Copyright (c) 2020 Jan Duempelmann - * Copyright (c) 2020 Reinhard Panhuber - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "tusb_option.h" - -// Since TinyUSB doesn't use SOF for now, and this interrupt too often (1ms interval) -// We disable SOF for now until needed later on -#define USE_SOF 0 - -#if defined (STM32F105x8) || defined (STM32F105xB) || defined (STM32F105xC) || \ - defined (STM32F107xB) || defined (STM32F107xC) -#define STM32F1_SYNOPSYS -#endif - -#if defined (STM32L475xx) || defined (STM32L476xx) || \ - defined (STM32L485xx) || defined (STM32L486xx) || defined (STM32L496xx) || \ - defined (STM32L4R5xx) || defined (STM32L4R7xx) || defined (STM32L4R9xx) || \ - defined (STM32L4S5xx) || defined (STM32L4S7xx) || defined (STM32L4S9xx) -#define STM32L4_SYNOPSYS -#endif - -#if CFG_TUD_ENABLED && \ - ( (CFG_TUSB_MCU == OPT_MCU_STM32F1 && defined(STM32F1_SYNOPSYS)) || \ - CFG_TUSB_MCU == OPT_MCU_STM32F2 || \ - CFG_TUSB_MCU == OPT_MCU_STM32F4 || \ - CFG_TUSB_MCU == OPT_MCU_STM32F7 || \ - CFG_TUSB_MCU == OPT_MCU_STM32H7 || \ - (CFG_TUSB_MCU == OPT_MCU_STM32L4 && defined(STM32L4_SYNOPSYS) || \ - CFG_TUSB_MCU == OPT_MCU_GD32VF103 ) \ - ) - -// EP_MAX : Max number of bi-directional endpoints including EP0 -// EP_FIFO_SIZE : Size of dedicated USB SRAM -#if CFG_TUSB_MCU == OPT_MCU_STM32F1 -#include "stm32f1xx.h" -#define EP_MAX_FS 4 -#define EP_FIFO_SIZE_FS 1280 - -#elif CFG_TUSB_MCU == OPT_MCU_STM32F2 -#include "stm32f2xx.h" -#define EP_MAX_FS USB_OTG_FS_MAX_IN_ENDPOINTS -#define EP_FIFO_SIZE_FS USB_OTG_FS_TOTAL_FIFO_SIZE - -#elif CFG_TUSB_MCU == OPT_MCU_STM32F4 -#include "stm32f4xx.h" -#define EP_MAX_FS USB_OTG_FS_MAX_IN_ENDPOINTS -#define EP_FIFO_SIZE_FS USB_OTG_FS_TOTAL_FIFO_SIZE -#define EP_MAX_HS USB_OTG_HS_MAX_IN_ENDPOINTS -#define EP_FIFO_SIZE_HS USB_OTG_HS_TOTAL_FIFO_SIZE - -#elif CFG_TUSB_MCU == OPT_MCU_STM32H7 -#include "stm32h7xx.h" -#define EP_MAX_FS 9 -#define EP_FIFO_SIZE_FS 4096 -#define EP_MAX_HS 9 -#define EP_FIFO_SIZE_HS 4096 - -#elif CFG_TUSB_MCU == OPT_MCU_STM32F7 -#include "stm32f7xx.h" -#define EP_MAX_FS 6 -#define EP_FIFO_SIZE_FS 1280 -#define EP_MAX_HS 9 -#define EP_FIFO_SIZE_HS 4096 - -#elif CFG_TUSB_MCU == OPT_MCU_STM32L4 -#include "stm32l4xx.h" -#define EP_MAX_FS 6 -#define EP_FIFO_SIZE_FS 1280 - -#elif CFG_TUSB_MCU == OPT_MCU_GD32VF103 -#include "synopsys_common.h" - -// for remote wakeup delay -#define __NOP() __asm volatile ("nop") - -// These numbers are the same for the whole GD32VF103 family. -#define OTG_FS_IRQn 86 -#define EP_MAX_FS 4 -#define EP_FIFO_SIZE_FS 1280 - -// The GD32VF103 is a RISC-V MCU, which implements the ECLIC Core-Local -// Interrupt Controller by Nuclei. It is nearly API compatible to the -// NVIC used by ARM MCUs. -#define ECLIC_INTERRUPT_ENABLE_BASE 0xD2001001UL - -#define NVIC_EnableIRQ __eclic_enable_interrupt -#define NVIC_DisableIRQ __eclic_disable_interrupt - -static inline void __eclic_enable_interrupt (uint32_t irq) { - *(volatile uint8_t*)(ECLIC_INTERRUPT_ENABLE_BASE + (irq * 4)) = 1; -} - -static inline void __eclic_disable_interrupt (uint32_t irq){ - *(volatile uint8_t*)(ECLIC_INTERRUPT_ENABLE_BASE + (irq * 4)) = 0; -} - -#else -#error "Unsupported MCUs" -#endif - -#include "device/dcd.h" - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ - -// On STM32 we associate Port0 to OTG_FS, and Port1 to OTG_HS -#if TUD_OPT_RHPORT == 0 -#define EP_MAX EP_MAX_FS -#define EP_FIFO_SIZE EP_FIFO_SIZE_FS -#define RHPORT_REGS_BASE USB_OTG_FS_PERIPH_BASE -#define RHPORT_IRQn OTG_FS_IRQn - -#else -#define EP_MAX EP_MAX_HS -#define EP_FIFO_SIZE EP_FIFO_SIZE_HS -#define RHPORT_REGS_BASE USB_OTG_HS_PERIPH_BASE -#define RHPORT_IRQn OTG_HS_IRQn - -#endif - -#define GLOBAL_BASE(_port) ((USB_OTG_GlobalTypeDef*) RHPORT_REGS_BASE) -#define DEVICE_BASE(_port) (USB_OTG_DeviceTypeDef *) (RHPORT_REGS_BASE + USB_OTG_DEVICE_BASE) -#define OUT_EP_BASE(_port) (USB_OTG_OUTEndpointTypeDef *) (RHPORT_REGS_BASE + USB_OTG_OUT_ENDPOINT_BASE) -#define IN_EP_BASE(_port) (USB_OTG_INEndpointTypeDef *) (RHPORT_REGS_BASE + USB_OTG_IN_ENDPOINT_BASE) -#define FIFO_BASE(_port, _x) ((volatile uint32_t *) (RHPORT_REGS_BASE + USB_OTG_FIFO_BASE + (_x) * USB_OTG_FIFO_SIZE)) - -enum -{ - DCD_HIGH_SPEED = 0, // Highspeed mode - DCD_FULL_SPEED_USE_HS = 1, // Full speed in Highspeed port (probably with internal PHY) - DCD_FULL_SPEED = 3, // Full speed with internal PHY -}; - -static TU_ATTR_ALIGNED(4) uint32_t _setup_packet[2]; - -typedef struct { - uint8_t * buffer; - tu_fifo_t * ff; - uint16_t total_len; - uint16_t max_size; - uint8_t interval; -} xfer_ctl_t; - -typedef volatile uint32_t * usb_fifo_t; - -xfer_ctl_t xfer_status[EP_MAX][2]; -#define XFER_CTL_BASE(_ep, _dir) &xfer_status[_ep][_dir] - -// EP0 transfers are limited to 1 packet - larger sizes has to be split -static uint16_t ep0_pending[2]; // Index determines direction as tusb_dir_t type - -// TX FIFO RAM allocation so far in words - RX FIFO size is readily available from usb_otg->GRXFSIZ -static uint16_t _allocated_fifo_words_tx; // TX FIFO size in words (IN EPs) -static bool _out_ep_closed; // Flag to check if RX FIFO size needs an update (reduce its size) - -// Calculate the RX FIFO size according to recommendations from reference manual -static inline uint16_t calc_rx_ff_size(uint16_t ep_size) -{ - return 15 + 2*(ep_size/4) + 2*EP_MAX; -} - -static void update_grxfsiz(uint8_t rhport) -{ - (void) rhport; - - USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - - // Determine largest EP size for RX FIFO - uint16_t max_epsize = 0; - for (uint8_t epnum = 0; epnum < EP_MAX; epnum++) - { - max_epsize = tu_max16(max_epsize, xfer_status[epnum][TUSB_DIR_OUT].max_size); - } - - // Update size of RX FIFO - usb_otg->GRXFSIZ = calc_rx_ff_size(max_epsize); -} - -// Setup the control endpoint 0. -static void bus_reset(uint8_t rhport) -{ - (void) rhport; - - USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - USB_OTG_OUTEndpointTypeDef * out_ep = OUT_EP_BASE(rhport); - USB_OTG_INEndpointTypeDef * in_ep = IN_EP_BASE(rhport); - - tu_memclr(xfer_status, sizeof(xfer_status)); - _out_ep_closed = false; - - // clear device address - dev->DCFG &= ~USB_OTG_DCFG_DAD_Msk; - - // 1. NAK for all OUT endpoints - for(uint8_t n = 0; n < EP_MAX; n++) { - out_ep[n].DOEPCTL |= USB_OTG_DOEPCTL_SNAK; - } - - // 2. Un-mask interrupt bits - dev->DAINTMSK = (1 << USB_OTG_DAINTMSK_OEPM_Pos) | (1 << USB_OTG_DAINTMSK_IEPM_Pos); - dev->DOEPMSK = USB_OTG_DOEPMSK_STUPM | USB_OTG_DOEPMSK_XFRCM; - dev->DIEPMSK = USB_OTG_DIEPMSK_TOM | USB_OTG_DIEPMSK_XFRCM; - - // "USB Data FIFOs" section in reference manual - // Peripheral FIFO architecture - // - // The FIFO is split up in a lower part where the RX FIFO is located and an upper part where the TX FIFOs start. - // We do this to allow the RX FIFO to grow dynamically which is possible since the free space is located - // between the RX and TX FIFOs. This is required by ISO OUT EPs which need a bigger FIFO than the standard - // configuration done below. - // - // Dynamically FIFO sizes are of interest only for ISO EPs since all others are usually not opened and closed. - // All EPs other than ISO are opened as soon as the driver starts up i.e. when the host sends a - // configure interface command. Hence, all IN EPs other the ISO will be located at the top. IN ISO EPs are usually - // opened when the host sends an additional command: setInterface. At this point in time - // the ISO EP will be located next to the free space and can change its size. In case more IN EPs change its size - // an additional memory - // - // --------------- 320 or 1024 ( 1280 or 4096 bytes ) - // | IN FIFO 0 | - // --------------- (320 or 1024) - 16 - // | IN FIFO 1 | - // --------------- (320 or 1024) - 16 - x - // | . . . . | - // --------------- (320 or 1024) - 16 - x - y - ... - z - // | IN FIFO MAX | - // --------------- - // | FREE | - // --------------- GRXFSIZ - // | OUT FIFO | - // | ( Shared ) | - // --------------- 0 - // - // According to "FIFO RAM allocation" section in RM, FIFO RAM are allocated as follows (each word 32-bits): - // - Each EP IN needs at least max packet size, 16 words is sufficient for EP0 IN - // - // - All EP OUT shared a unique OUT FIFO which uses - // - 13 for setup packets + control words (up to 3 setup packets). - // - 1 for global NAK (not required/used here). - // - Largest-EPsize / 4 + 1. ( FS: 64 bytes, HS: 512 bytes). Recommended is "2 x (Largest-EPsize/4) + 1" - // - 2 for each used OUT endpoint - // - // Therefore GRXFSIZ = 13 + 1 + 1 + 2 x (Largest-EPsize/4) + 2 x EPOUTnum - // - FullSpeed (64 Bytes ): GRXFSIZ = 15 + 2 x 16 + 2 x EP_MAX = 47 + 2 x EP_MAX - // - Highspeed (512 bytes): GRXFSIZ = 15 + 2 x 128 + 2 x EP_MAX = 271 + 2 x EP_MAX - // - // NOTE: Largest-EPsize & EPOUTnum is actual used endpoints in configuration. Since DCD has no knowledge - // of the overall picture yet. We will use the worst scenario: largest possible + EP_MAX - // - // For Isochronous, largest EP size can be 1023/1024 for FS/HS respectively. In addition if multiple ISO - // are enabled at least "2 x (Largest-EPsize/4) + 1" are recommended. Maybe provide a macro for application to - // overwrite this. - - usb_otg->GRXFSIZ = calc_rx_ff_size(TUD_OPT_HIGH_SPEED ? 512 : 64); - - _allocated_fifo_words_tx = 16; - - // Control IN uses FIFO 0 with 64 bytes ( 16 32-bit word ) - usb_otg->DIEPTXF0_HNPTXFSIZ = (16 << USB_OTG_TX0FD_Pos) | (EP_FIFO_SIZE/4 - _allocated_fifo_words_tx); - - // Fixed control EP0 size to 64 bytes - in_ep[0].DIEPCTL &= ~(0x03 << USB_OTG_DIEPCTL_MPSIZ_Pos); - xfer_status[0][TUSB_DIR_OUT].max_size = xfer_status[0][TUSB_DIR_IN].max_size = 64; - - out_ep[0].DOEPTSIZ |= (3 << USB_OTG_DOEPTSIZ_STUPCNT_Pos); - - usb_otg->GINTMSK |= USB_OTG_GINTMSK_OEPINT | USB_OTG_GINTMSK_IEPINT; -} - -// Set turn-around timeout according to link speed -extern uint32_t SystemCoreClock; -static void set_turnaround(USB_OTG_GlobalTypeDef * usb_otg, tusb_speed_t speed) -{ - usb_otg->GUSBCFG &= ~USB_OTG_GUSBCFG_TRDT; - - if ( speed == TUSB_SPEED_HIGH ) - { - // Use fixed 0x09 for Highspeed - usb_otg->GUSBCFG |= (0x09 << USB_OTG_GUSBCFG_TRDT_Pos); - } - else - { - // Turnaround timeout depends on the MCU clock - uint32_t turnaround; - - if ( SystemCoreClock >= 32000000U ) - turnaround = 0x6U; - else if ( SystemCoreClock >= 27500000U ) - turnaround = 0x7U; - else if ( SystemCoreClock >= 24000000U ) - turnaround = 0x8U; - else if ( SystemCoreClock >= 21800000U ) - turnaround = 0x9U; - else if ( SystemCoreClock >= 20000000U ) - turnaround = 0xAU; - else if ( SystemCoreClock >= 18500000U ) - turnaround = 0xBU; - else if ( SystemCoreClock >= 17200000U ) - turnaround = 0xCU; - else if ( SystemCoreClock >= 16000000U ) - turnaround = 0xDU; - else if ( SystemCoreClock >= 15000000U ) - turnaround = 0xEU; - else - turnaround = 0xFU; - - // Fullspeed depends on MCU clocks, but we will use 0x06 for 32+ Mhz - usb_otg->GUSBCFG |= (turnaround << USB_OTG_GUSBCFG_TRDT_Pos); - } -} - -static tusb_speed_t get_speed(uint8_t rhport) -{ - (void) rhport; - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - uint32_t const enum_spd = (dev->DSTS & USB_OTG_DSTS_ENUMSPD_Msk) >> USB_OTG_DSTS_ENUMSPD_Pos; - return (enum_spd == DCD_HIGH_SPEED) ? TUSB_SPEED_HIGH : TUSB_SPEED_FULL; -} - -static void set_speed(uint8_t rhport, tusb_speed_t speed) -{ - uint32_t bitvalue; - - if ( rhport == 1 ) - { - bitvalue = ((TUSB_SPEED_HIGH == speed) ? DCD_HIGH_SPEED : DCD_FULL_SPEED_USE_HS); - } - else - { - bitvalue = DCD_FULL_SPEED; - } - - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - - // Clear and set speed bits - dev->DCFG &= ~(3 << USB_OTG_DCFG_DSPD_Pos); - dev->DCFG |= (bitvalue << USB_OTG_DCFG_DSPD_Pos); -} - -#if defined(USB_HS_PHYC) -static bool USB_HS_PHYCInit(void) -{ - USB_HS_PHYC_GlobalTypeDef *usb_hs_phyc = (USB_HS_PHYC_GlobalTypeDef*) USB_HS_PHYC_CONTROLLER_BASE; - - // Enable LDO: Note STM32F72/3xx Reference Manual rev 3 June 2018 incorrectly defined this bit as Disabled !! - usb_hs_phyc->USB_HS_PHYC_LDO |= USB_HS_PHYC_LDO_ENABLE; - - // Wait until LDO ready - while ( 0 == (usb_hs_phyc->USB_HS_PHYC_LDO & USB_HS_PHYC_LDO_STATUS) ) {} - - uint32_t phyc_pll = 0; - - // TODO Try to get HSE_VALUE from registers instead of depending CFLAGS - switch ( HSE_VALUE ) - { - case 12000000: phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_12MHZ ; break; - case 12500000: phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_12_5MHZ ; break; - case 16000000: phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_16MHZ ; break; - case 24000000: phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_24MHZ ; break; - case 25000000: phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_25MHZ ; break; - case 32000000: phyc_pll = USB_HS_PHYC_PLL1_PLLSEL_Msk ; break; // Value not defined in header - default: - TU_ASSERT(0); - } - usb_hs_phyc->USB_HS_PHYC_PLL = phyc_pll; - - // Control the tuning interface of the High Speed PHY - // Use magic value (USB_HS_PHYC_TUNE_VALUE) from ST driver - usb_hs_phyc->USB_HS_PHYC_TUNE |= 0x00000F13U; - - // Enable PLL internal PHY - usb_hs_phyc->USB_HS_PHYC_PLL |= USB_HS_PHYC_PLL_PLLEN; - - // Original ST code has 2 ms delay for PLL stabilization. - // Primitive test shows that more than 10 USB un/replug cycle showed no error with enumeration - - return true; -} -#endif - -static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t const dir, uint16_t const num_packets, uint16_t total_bytes) -{ - (void) rhport; - - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - USB_OTG_OUTEndpointTypeDef * out_ep = OUT_EP_BASE(rhport); - USB_OTG_INEndpointTypeDef * in_ep = IN_EP_BASE(rhport); - - // EP0 is limited to one packet each xfer - // We use multiple transaction of xfer->max_size length to get a whole transfer done - if(epnum == 0) { - xfer_ctl_t * const xfer = XFER_CTL_BASE(epnum, dir); - total_bytes = tu_min16(ep0_pending[dir], xfer->max_size); - ep0_pending[dir] -= total_bytes; - } - - // IN and OUT endpoint xfers are interrupt-driven, we just schedule them here. - if(dir == TUSB_DIR_IN) { - // A full IN transfer (multiple packets, possibly) triggers XFRC. - in_ep[epnum].DIEPTSIZ = (num_packets << USB_OTG_DIEPTSIZ_PKTCNT_Pos) | - ((total_bytes << USB_OTG_DIEPTSIZ_XFRSIZ_Pos) & USB_OTG_DIEPTSIZ_XFRSIZ_Msk); - - in_ep[epnum].DIEPCTL |= USB_OTG_DIEPCTL_EPENA | USB_OTG_DIEPCTL_CNAK; - // For ISO endpoint set correct odd/even bit for next frame. - if ((in_ep[epnum].DIEPCTL & USB_OTG_DIEPCTL_EPTYP) == USB_OTG_DIEPCTL_EPTYP_0 && (XFER_CTL_BASE(epnum, dir))->interval == 1) - { - // Take odd/even bit from frame counter. - uint32_t const odd_frame_now = (dev->DSTS & (1u << USB_OTG_DSTS_FNSOF_Pos)); - in_ep[epnum].DIEPCTL |= (odd_frame_now ? USB_OTG_DIEPCTL_SD0PID_SEVNFRM_Msk : USB_OTG_DIEPCTL_SODDFRM_Msk); - } - // Enable fifo empty interrupt only if there are something to put in the fifo. - if(total_bytes != 0) { - dev->DIEPEMPMSK |= (1 << epnum); - } - } else { - // A full OUT transfer (multiple packets, possibly) triggers XFRC. - out_ep[epnum].DOEPTSIZ &= ~(USB_OTG_DOEPTSIZ_PKTCNT_Msk | USB_OTG_DOEPTSIZ_XFRSIZ); - out_ep[epnum].DOEPTSIZ |= (num_packets << USB_OTG_DOEPTSIZ_PKTCNT_Pos) | - ((total_bytes << USB_OTG_DOEPTSIZ_XFRSIZ_Pos) & USB_OTG_DOEPTSIZ_XFRSIZ_Msk); - - out_ep[epnum].DOEPCTL |= USB_OTG_DOEPCTL_EPENA | USB_OTG_DOEPCTL_CNAK; - if ((out_ep[epnum].DOEPCTL & USB_OTG_DOEPCTL_EPTYP) == USB_OTG_DOEPCTL_EPTYP_0 && (XFER_CTL_BASE(epnum, dir))->interval == 1) - { - // Take odd/even bit from frame counter. - uint32_t const odd_frame_now = (dev->DSTS & (1u << USB_OTG_DSTS_FNSOF_Pos)); - out_ep[epnum].DOEPCTL |= (odd_frame_now ? USB_OTG_DOEPCTL_SD0PID_SEVNFRM_Msk : USB_OTG_DOEPCTL_SODDFRM_Msk); - } - } -} - -/*------------------------------------------------------------------*/ -/* Controller API - *------------------------------------------------------------------*/ -void dcd_init (uint8_t rhport) -{ - // Programming model begins in the last section of the chapter on the USB - // peripheral in each Reference Manual. - - USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - - // No HNP/SRP (no OTG support), program timeout later. - if ( rhport == 1 ) - { - // On selected MCUs HS port1 can be used with external PHY via ULPI interface -#if CFG_TUSB_RHPORT1_MODE & OPT_MODE_HIGH_SPEED - // deactivate internal PHY - usb_otg->GCCFG &= ~USB_OTG_GCCFG_PWRDWN; - - // Init The UTMI Interface - usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_TSDPS | USB_OTG_GUSBCFG_ULPIFSLS | USB_OTG_GUSBCFG_PHYSEL); - - // Select default internal VBUS Indicator and Drive for ULPI - usb_otg->GUSBCFG &= ~(USB_OTG_GUSBCFG_ULPIEVBUSD | USB_OTG_GUSBCFG_ULPIEVBUSI); -#else - usb_otg->GUSBCFG |= USB_OTG_GUSBCFG_PHYSEL; -#endif - -#if defined(USB_HS_PHYC) - // Highspeed with embedded UTMI PHYC - - // Select UTMI Interface - usb_otg->GUSBCFG &= ~USB_OTG_GUSBCFG_ULPI_UTMI_SEL; - usb_otg->GCCFG |= USB_OTG_GCCFG_PHYHSEN; - - // Enables control of a High Speed USB PHY - USB_HS_PHYCInit(); -#endif - } else - { - // Enable internal PHY - usb_otg->GUSBCFG |= USB_OTG_GUSBCFG_PHYSEL; - } - - // Reset core after selecting PHY - // Wait AHB IDLE, reset then wait until it is cleared - while ((usb_otg->GRSTCTL & USB_OTG_GRSTCTL_AHBIDL) == 0U) {} - usb_otg->GRSTCTL |= USB_OTG_GRSTCTL_CSRST; - while ((usb_otg->GRSTCTL & USB_OTG_GRSTCTL_CSRST) == USB_OTG_GRSTCTL_CSRST) {} - - // Restart PHY clock - *((volatile uint32_t *)(RHPORT_REGS_BASE + USB_OTG_PCGCCTL_BASE)) = 0; - - // Clear all interrupts - usb_otg->GINTSTS |= usb_otg->GINTSTS; - - // Required as part of core initialization. - // TODO: How should mode mismatch be handled? It will cause - // the core to stop working/require reset. - usb_otg->GINTMSK |= USB_OTG_GINTMSK_OTGINT | USB_OTG_GINTMSK_MMISM; - - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - - // If USB host misbehaves during status portion of control xfer - // (non zero-length packet), send STALL back and discard. - dev->DCFG |= USB_OTG_DCFG_NZLSOHSK; - - set_speed(rhport, TUD_OPT_HIGH_SPEED ? TUSB_SPEED_HIGH : TUSB_SPEED_FULL); - - // Enable internal USB transceiver, unless using HS core (port 1) with external PHY. - if (!(rhport == 1 && (CFG_TUSB_RHPORT1_MODE & OPT_MODE_HIGH_SPEED))) usb_otg->GCCFG |= USB_OTG_GCCFG_PWRDWN; - - usb_otg->GINTMSK |= USB_OTG_GINTMSK_USBRST | USB_OTG_GINTMSK_ENUMDNEM | - USB_OTG_GINTMSK_USBSUSPM | USB_OTG_GINTMSK_WUIM | - USB_OTG_GINTMSK_RXFLVLM | (USE_SOF ? USB_OTG_GINTMSK_SOFM : 0); - - // Enable global interrupt - usb_otg->GAHBCFG |= USB_OTG_GAHBCFG_GINT; - - dcd_connect(rhport); -} - -void dcd_int_enable (uint8_t rhport) -{ - (void) rhport; - NVIC_EnableIRQ(RHPORT_IRQn); -} - -void dcd_int_disable (uint8_t rhport) -{ - (void) rhport; - NVIC_DisableIRQ(RHPORT_IRQn); -} - -void dcd_set_address (uint8_t rhport, uint8_t dev_addr) -{ - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - dev->DCFG = (dev->DCFG & ~USB_OTG_DCFG_DAD_Msk) | (dev_addr << USB_OTG_DCFG_DAD_Pos); - - // Response with status after changing device address - dcd_edpt_xfer(rhport, tu_edpt_addr(0, TUSB_DIR_IN), NULL, 0); -} - -static void remote_wakeup_delay(void) -{ - // try to delay for 1 ms - uint32_t count = SystemCoreClock / 1000; - while ( count-- ) - { - __NOP(); - } -} - -void dcd_remote_wakeup(uint8_t rhport) -{ - (void) rhport; - - USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - - // set remote wakeup - dev->DCTL |= USB_OTG_DCTL_RWUSIG; - - // enable SOF to detect bus resume - usb_otg->GINTSTS = USB_OTG_GINTSTS_SOF; - usb_otg->GINTMSK |= USB_OTG_GINTMSK_SOFM; - - // Per specs: remote wakeup signal bit must be clear within 1-15ms - remote_wakeup_delay(); - - dev->DCTL &= ~USB_OTG_DCTL_RWUSIG; -} - -void dcd_connect(uint8_t rhport) -{ - (void) rhport; - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - dev->DCTL &= ~USB_OTG_DCTL_SDIS; -} - -void dcd_disconnect(uint8_t rhport) -{ - (void) rhport; - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - dev->DCTL |= USB_OTG_DCTL_SDIS; -} - -void dcd_sof_enable(uint8_t rhport, bool en) -{ - (void) rhport; - (void) en; - - // TODO implement later -} - -/*------------------------------------------------------------------*/ -/* DCD Endpoint port - *------------------------------------------------------------------*/ - -bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) -{ - (void) rhport; - - USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - USB_OTG_OUTEndpointTypeDef * out_ep = OUT_EP_BASE(rhport); - USB_OTG_INEndpointTypeDef * in_ep = IN_EP_BASE(rhport); - - uint8_t const epnum = tu_edpt_number(desc_edpt->bEndpointAddress); - uint8_t const dir = tu_edpt_dir(desc_edpt->bEndpointAddress); - - TU_ASSERT(epnum < EP_MAX); - - xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, dir); - xfer->max_size = tu_edpt_packet_size(desc_edpt); - xfer->interval = desc_edpt->bInterval; - - uint16_t const fifo_size = (xfer->max_size + 3) / 4; // Round up to next full word - - if(dir == TUSB_DIR_OUT) - { - // Calculate required size of RX FIFO - uint16_t const sz = calc_rx_ff_size(4*fifo_size); - - // If size_rx needs to be extended check if possible and if so enlarge it - if (usb_otg->GRXFSIZ < sz) - { - TU_ASSERT(sz + _allocated_fifo_words_tx <= EP_FIFO_SIZE/4); - - // Enlarge RX FIFO - usb_otg->GRXFSIZ = sz; - } - - out_ep[epnum].DOEPCTL |= (1 << USB_OTG_DOEPCTL_USBAEP_Pos) | - (desc_edpt->bmAttributes.xfer << USB_OTG_DOEPCTL_EPTYP_Pos) | - (desc_edpt->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? USB_OTG_DOEPCTL_SD0PID_SEVNFRM : 0) | - (xfer->max_size << USB_OTG_DOEPCTL_MPSIZ_Pos); - - dev->DAINTMSK |= (1 << (USB_OTG_DAINTMSK_OEPM_Pos + epnum)); - } - else - { - // "USB Data FIFOs" section in reference manual - // Peripheral FIFO architecture - // - // --------------- 320 or 1024 ( 1280 or 4096 bytes ) - // | IN FIFO 0 | - // --------------- (320 or 1024) - 16 - // | IN FIFO 1 | - // --------------- (320 or 1024) - 16 - x - // | . . . . | - // --------------- (320 or 1024) - 16 - x - y - ... - z - // | IN FIFO MAX | - // --------------- - // | FREE | - // --------------- GRXFSIZ - // | OUT FIFO | - // | ( Shared ) | - // --------------- 0 - // - // In FIFO is allocated by following rules: - // - IN EP 1 gets FIFO 1, IN EP "n" gets FIFO "n". - - // Check if free space is available - TU_ASSERT(_allocated_fifo_words_tx + fifo_size + usb_otg->GRXFSIZ <= EP_FIFO_SIZE/4); - - _allocated_fifo_words_tx += fifo_size; - - TU_LOG(2, " Allocated %u bytes at offset %u", fifo_size*4, EP_FIFO_SIZE-_allocated_fifo_words_tx*4); - - // DIEPTXF starts at FIFO #1. - // Both TXFD and TXSA are in unit of 32-bit words. - usb_otg->DIEPTXF[epnum - 1] = (fifo_size << USB_OTG_DIEPTXF_INEPTXFD_Pos) | (EP_FIFO_SIZE/4 - _allocated_fifo_words_tx); - - in_ep[epnum].DIEPCTL |= (1 << USB_OTG_DIEPCTL_USBAEP_Pos) | - (epnum << USB_OTG_DIEPCTL_TXFNUM_Pos) | - (desc_edpt->bmAttributes.xfer << USB_OTG_DIEPCTL_EPTYP_Pos) | - (desc_edpt->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? USB_OTG_DIEPCTL_SD0PID_SEVNFRM : 0) | - (xfer->max_size << USB_OTG_DIEPCTL_MPSIZ_Pos); - - dev->DAINTMSK |= (1 << (USB_OTG_DAINTMSK_IEPM_Pos + epnum)); - } - - return true; -} - -// Close all non-control endpoints, cancel all pending transfers if any. -void dcd_edpt_close_all (uint8_t rhport) -{ - (void) rhport; - -// USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - USB_OTG_OUTEndpointTypeDef * out_ep = OUT_EP_BASE(rhport); - USB_OTG_INEndpointTypeDef * in_ep = IN_EP_BASE(rhport); - - // Disable non-control interrupt - dev->DAINTMSK = (1 << USB_OTG_DAINTMSK_OEPM_Pos) | (1 << USB_OTG_DAINTMSK_IEPM_Pos); - - for(uint8_t n = 1; n < EP_MAX; n++) - { - // disable OUT endpoint - out_ep[n].DOEPCTL = 0; - xfer_status[n][TUSB_DIR_OUT].max_size = 0; - - // disable IN endpoint - in_ep[n].DIEPCTL = 0; - xfer_status[n][TUSB_DIR_IN].max_size = 0; - } - - // reset allocated fifo IN - _allocated_fifo_words_tx = 16; -} - -bool dcd_edpt_xfer (uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes) -{ - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, dir); - xfer->buffer = buffer; - xfer->ff = NULL; - xfer->total_len = total_bytes; - - // EP0 can only handle one packet - if(epnum == 0) { - ep0_pending[dir] = total_bytes; - // Schedule the first transaction for EP0 transfer - edpt_schedule_packets(rhport, epnum, dir, 1, ep0_pending[dir]); - return true; - } - - uint16_t num_packets = (total_bytes / xfer->max_size); - uint16_t const short_packet_size = total_bytes % xfer->max_size; - - // Zero-size packet is special case. - if(short_packet_size > 0 || (total_bytes == 0)) { - num_packets++; - } - - // Schedule packets to be sent within interrupt - edpt_schedule_packets(rhport, epnum, dir, num_packets, total_bytes); - - return true; -} - -// The number of bytes has to be given explicitly to allow more flexible control of how many -// bytes should be written and second to keep the return value free to give back a boolean -// success message. If total_bytes is too big, the FIFO will copy only what is available -// into the USB buffer! -bool dcd_edpt_xfer_fifo (uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16_t total_bytes) -{ - // USB buffers always work in bytes so to avoid unnecessary divisions we demand item_size = 1 - TU_ASSERT(ff->item_size == 1); - - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, dir); - xfer->buffer = NULL; - xfer->ff = ff; - xfer->total_len = total_bytes; - - uint16_t num_packets = (total_bytes / xfer->max_size); - uint16_t const short_packet_size = total_bytes % xfer->max_size; - - // Zero-size packet is special case. - if(short_packet_size > 0 || (total_bytes == 0)) num_packets++; - - // Schedule packets to be sent within interrupt - edpt_schedule_packets(rhport, epnum, dir, num_packets, total_bytes); - - return true; -} - -static void dcd_edpt_disable (uint8_t rhport, uint8_t ep_addr, bool stall) -{ - (void) rhport; - - USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - USB_OTG_OUTEndpointTypeDef * out_ep = OUT_EP_BASE(rhport); - USB_OTG_INEndpointTypeDef * in_ep = IN_EP_BASE(rhport); - - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - if(dir == TUSB_DIR_IN) { - // Only disable currently enabled non-control endpoint - if ( (epnum == 0) || !(in_ep[epnum].DIEPCTL & USB_OTG_DIEPCTL_EPENA) ){ - in_ep[epnum].DIEPCTL |= USB_OTG_DIEPCTL_SNAK | (stall ? USB_OTG_DIEPCTL_STALL : 0); - } else { - // Stop transmitting packets and NAK IN xfers. - in_ep[epnum].DIEPCTL |= USB_OTG_DIEPCTL_SNAK; - while((in_ep[epnum].DIEPINT & USB_OTG_DIEPINT_INEPNE) == 0); - - // Disable the endpoint. - in_ep[epnum].DIEPCTL |= USB_OTG_DIEPCTL_EPDIS | (stall ? USB_OTG_DIEPCTL_STALL : 0); - while((in_ep[epnum].DIEPINT & USB_OTG_DIEPINT_EPDISD_Msk) == 0); - in_ep[epnum].DIEPINT = USB_OTG_DIEPINT_EPDISD; - } - - // Flush the FIFO, and wait until we have confirmed it cleared. - usb_otg->GRSTCTL |= (epnum << USB_OTG_GRSTCTL_TXFNUM_Pos); - usb_otg->GRSTCTL |= USB_OTG_GRSTCTL_TXFFLSH; - while((usb_otg->GRSTCTL & USB_OTG_GRSTCTL_TXFFLSH_Msk) != 0); - } else { - // Only disable currently enabled non-control endpoint - if ( (epnum == 0) || !(out_ep[epnum].DOEPCTL & USB_OTG_DOEPCTL_EPENA) ){ - out_ep[epnum].DOEPCTL |= stall ? USB_OTG_DOEPCTL_STALL : 0; - } else { - // Asserting GONAK is required to STALL an OUT endpoint. - // Simpler to use polling here, we don't use the "B"OUTNAKEFF interrupt - // anyway, and it can't be cleared by user code. If this while loop never - // finishes, we have bigger problems than just the stack. - dev->DCTL |= USB_OTG_DCTL_SGONAK; - while((usb_otg->GINTSTS & USB_OTG_GINTSTS_BOUTNAKEFF_Msk) == 0); - - // Ditto here- disable the endpoint. - out_ep[epnum].DOEPCTL |= USB_OTG_DOEPCTL_EPDIS | (stall ? USB_OTG_DOEPCTL_STALL : 0); - while((out_ep[epnum].DOEPINT & USB_OTG_DOEPINT_EPDISD_Msk) == 0); - out_ep[epnum].DOEPINT = USB_OTG_DOEPINT_EPDISD; - - // Allow other OUT endpoints to keep receiving. - dev->DCTL |= USB_OTG_DCTL_CGONAK; - } - } -} - -/** - * Close an endpoint. - */ -void dcd_edpt_close (uint8_t rhport, uint8_t ep_addr) -{ - USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - dcd_edpt_disable(rhport, ep_addr, false); - - // Update max_size - xfer_status[epnum][dir].max_size = 0; // max_size = 0 marks a disabled EP - required for changing FIFO allocation - - if (dir == TUSB_DIR_IN) - { - uint16_t const fifo_size = (usb_otg->DIEPTXF[epnum - 1] & USB_OTG_DIEPTXF_INEPTXFD_Msk) >> USB_OTG_DIEPTXF_INEPTXFD_Pos; - uint16_t const fifo_start = (usb_otg->DIEPTXF[epnum - 1] & USB_OTG_DIEPTXF_INEPTXSA_Msk) >> USB_OTG_DIEPTXF_INEPTXSA_Pos; - // For now only the last opened endpoint can be closed without fuss. - TU_ASSERT(fifo_start == EP_FIFO_SIZE/4 - _allocated_fifo_words_tx,); - _allocated_fifo_words_tx -= fifo_size; - } - else - { - _out_ep_closed = true; // Set flag such that RX FIFO gets reduced in size once RX FIFO is empty - } -} - -void dcd_edpt_stall (uint8_t rhport, uint8_t ep_addr) -{ - dcd_edpt_disable(rhport, ep_addr, true); -} - -void dcd_edpt_clear_stall (uint8_t rhport, uint8_t ep_addr) -{ - (void) rhport; - - USB_OTG_OUTEndpointTypeDef * out_ep = OUT_EP_BASE(rhport); - USB_OTG_INEndpointTypeDef * in_ep = IN_EP_BASE(rhport); - - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - // Clear stall and reset data toggle - if(dir == TUSB_DIR_IN) { - in_ep[epnum].DIEPCTL &= ~USB_OTG_DIEPCTL_STALL; - in_ep[epnum].DIEPCTL |= USB_OTG_DIEPCTL_SD0PID_SEVNFRM; - } else { - out_ep[epnum].DOEPCTL &= ~USB_OTG_DOEPCTL_STALL; - out_ep[epnum].DOEPCTL |= USB_OTG_DOEPCTL_SD0PID_SEVNFRM; - } -} - -/*------------------------------------------------------------------*/ - -// Read a single data packet from receive FIFO -static void read_fifo_packet(uint8_t rhport, uint8_t * dst, uint16_t len) -{ - (void) rhport; - - usb_fifo_t rx_fifo = FIFO_BASE(rhport, 0); - - // Reading full available 32 bit words from fifo - uint16_t full_words = len >> 2; - for(uint16_t i = 0; i < full_words; i++) { - uint32_t tmp = *rx_fifo; - dst[0] = tmp & 0x000000FF; - dst[1] = (tmp & 0x0000FF00) >> 8; - dst[2] = (tmp & 0x00FF0000) >> 16; - dst[3] = (tmp & 0xFF000000) >> 24; - dst += 4; - } - - // Read the remaining 1-3 bytes from fifo - uint8_t bytes_rem = len & 0x03; - if(bytes_rem != 0) { - uint32_t tmp = *rx_fifo; - dst[0] = tmp & 0x000000FF; - if(bytes_rem > 1) { - dst[1] = (tmp & 0x0000FF00) >> 8; - } - if(bytes_rem > 2) { - dst[2] = (tmp & 0x00FF0000) >> 16; - } - } -} - -// Write a single data packet to EPIN FIFO -static void write_fifo_packet(uint8_t rhport, uint8_t fifo_num, uint8_t * src, uint16_t len) -{ - (void) rhport; - - usb_fifo_t tx_fifo = FIFO_BASE(rhport, fifo_num); - - // Pushing full available 32 bit words to fifo - uint16_t full_words = len >> 2; - for(uint16_t i = 0; i < full_words; i++){ - *tx_fifo = (src[3] << 24) | (src[2] << 16) | (src[1] << 8) | src[0]; - src += 4; - } - - // Write the remaining 1-3 bytes into fifo - uint8_t bytes_rem = len & 0x03; - if(bytes_rem){ - uint32_t tmp_word = 0; - tmp_word |= src[0]; - if(bytes_rem > 1){ - tmp_word |= src[1] << 8; - } - if(bytes_rem > 2){ - tmp_word |= src[2] << 16; - } - *tx_fifo = tmp_word; - } -} - -static void handle_rxflvl_ints(uint8_t rhport, USB_OTG_OUTEndpointTypeDef * out_ep) { - USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - usb_fifo_t rx_fifo = FIFO_BASE(rhport, 0); - - // Pop control word off FIFO - uint32_t ctl_word = usb_otg->GRXSTSP; - uint8_t pktsts = (ctl_word & USB_OTG_GRXSTSP_PKTSTS_Msk) >> USB_OTG_GRXSTSP_PKTSTS_Pos; - uint8_t epnum = (ctl_word & USB_OTG_GRXSTSP_EPNUM_Msk) >> USB_OTG_GRXSTSP_EPNUM_Pos; - uint16_t bcnt = (ctl_word & USB_OTG_GRXSTSP_BCNT_Msk) >> USB_OTG_GRXSTSP_BCNT_Pos; - - switch(pktsts) { - case 0x01: // Global OUT NAK (Interrupt) - break; - - case 0x02: // Out packet recvd - { - xfer_ctl_t * xfer = XFER_CTL_BASE(epnum, TUSB_DIR_OUT); - - // Read packet off RxFIFO - if (xfer->ff) - { - // Ring buffer - tu_fifo_write_n_const_addr_full_words(xfer->ff, (const void *)(uintptr_t) rx_fifo, bcnt); - } - else - { - // Linear buffer - read_fifo_packet(rhport, xfer->buffer, bcnt); - - // Increment pointer to xfer data - xfer->buffer += bcnt; - } - - // Truncate transfer length in case of short packet - if(bcnt < xfer->max_size) { - xfer->total_len -= (out_ep[epnum].DOEPTSIZ & USB_OTG_DOEPTSIZ_XFRSIZ_Msk) >> USB_OTG_DOEPTSIZ_XFRSIZ_Pos; - if(epnum == 0) { - xfer->total_len -= ep0_pending[TUSB_DIR_OUT]; - ep0_pending[TUSB_DIR_OUT] = 0; - } - } - } - break; - - case 0x03: // Out packet done (Interrupt) - break; - - case 0x04: // Setup packet done (Interrupt) - out_ep[epnum].DOEPTSIZ |= (3 << USB_OTG_DOEPTSIZ_STUPCNT_Pos); - break; - - case 0x06: // Setup packet recvd - // We can receive up to three setup packets in succession, but - // only the last one is valid. - _setup_packet[0] = (* rx_fifo); - _setup_packet[1] = (* rx_fifo); - break; - - default: // Invalid - TU_BREAKPOINT(); - break; - } -} - -static void handle_epout_ints(uint8_t rhport, USB_OTG_DeviceTypeDef * dev, USB_OTG_OUTEndpointTypeDef * out_ep) { - // DAINT for a given EP clears when DOEPINTx is cleared. - // OEPINT will be cleared when DAINT's out bits are cleared. - for(uint8_t n = 0; n < EP_MAX; n++) { - xfer_ctl_t * xfer = XFER_CTL_BASE(n, TUSB_DIR_OUT); - - if(dev->DAINT & (1 << (USB_OTG_DAINT_OEPINT_Pos + n))) { - // SETUP packet Setup Phase done. - if(out_ep[n].DOEPINT & USB_OTG_DOEPINT_STUP) { - out_ep[n].DOEPINT = USB_OTG_DOEPINT_STUP; - dcd_event_setup_received(rhport, (uint8_t*) &_setup_packet[0], true); - } - - // OUT XFER complete - if(out_ep[n].DOEPINT & USB_OTG_DOEPINT_XFRC) { - out_ep[n].DOEPINT = USB_OTG_DOEPINT_XFRC; - - // EP0 can only handle one packet - if((n == 0) && ep0_pending[TUSB_DIR_OUT]) { - // Schedule another packet to be received. - edpt_schedule_packets(rhport, n, TUSB_DIR_OUT, 1, ep0_pending[TUSB_DIR_OUT]); - } else { - dcd_event_xfer_complete(rhport, n, xfer->total_len, XFER_RESULT_SUCCESS, true); - } - } - } - } -} - -static void handle_epin_ints(uint8_t rhport, USB_OTG_DeviceTypeDef * dev, USB_OTG_INEndpointTypeDef * in_ep) { - // DAINT for a given EP clears when DIEPINTx is cleared. - // IEPINT will be cleared when DAINT's out bits are cleared. - for ( uint8_t n = 0; n < EP_MAX; n++ ) - { - xfer_ctl_t *xfer = XFER_CTL_BASE(n, TUSB_DIR_IN); - - if ( dev->DAINT & (1 << (USB_OTG_DAINT_IEPINT_Pos + n)) ) - { - // IN XFER complete (entire xfer). - if ( in_ep[n].DIEPINT & USB_OTG_DIEPINT_XFRC ) - { - in_ep[n].DIEPINT = USB_OTG_DIEPINT_XFRC; - - // EP0 can only handle one packet - if((n == 0) && ep0_pending[TUSB_DIR_IN]) { - // Schedule another packet to be transmitted. - edpt_schedule_packets(rhport, n, TUSB_DIR_IN, 1, ep0_pending[TUSB_DIR_IN]); - } else { - dcd_event_xfer_complete(rhport, n | TUSB_DIR_IN_MASK, xfer->total_len, XFER_RESULT_SUCCESS, true); - } - } - - // XFER FIFO empty - if ( (in_ep[n].DIEPINT & USB_OTG_DIEPINT_TXFE) && (dev->DIEPEMPMSK & (1 << n)) ) - { - // DIEPINT's TXFE bit is read-only, software cannot clear it. - // It will only be cleared by hardware when written bytes is more than - // - 64 bytes or - // - Half of TX FIFO size (configured by DIEPTXF) - - uint16_t remaining_packets = (in_ep[n].DIEPTSIZ & USB_OTG_DIEPTSIZ_PKTCNT_Msk) >> USB_OTG_DIEPTSIZ_PKTCNT_Pos; - - // Process every single packet (only whole packets can be written to fifo) - for(uint16_t i = 0; i < remaining_packets; i++) - { - uint16_t const remaining_bytes = (in_ep[n].DIEPTSIZ & USB_OTG_DIEPTSIZ_XFRSIZ_Msk) >> USB_OTG_DIEPTSIZ_XFRSIZ_Pos; - - // Packet can not be larger than ep max size - uint16_t const packet_size = tu_min16(remaining_bytes, xfer->max_size); - - // It's only possible to write full packets into FIFO. Therefore DTXFSTS register of current - // EP has to be checked if the buffer can take another WHOLE packet - if(packet_size > ((in_ep[n].DTXFSTS & USB_OTG_DTXFSTS_INEPTFSAV_Msk) << 2)) break; - - // Push packet to Tx-FIFO - if (xfer->ff) - { - usb_fifo_t tx_fifo = FIFO_BASE(rhport, n); - tu_fifo_read_n_const_addr_full_words(xfer->ff, (void *)(uintptr_t) tx_fifo, packet_size); - } - else - { - write_fifo_packet(rhport, n, xfer->buffer, packet_size); - - // Increment pointer to xfer data - xfer->buffer += packet_size; - } - } - - // Turn off TXFE if all bytes are written. - if (((in_ep[n].DIEPTSIZ & USB_OTG_DIEPTSIZ_XFRSIZ_Msk) >> USB_OTG_DIEPTSIZ_XFRSIZ_Pos) == 0) - { - dev->DIEPEMPMSK &= ~(1 << n); - } - } - } - } -} - -void dcd_int_handler(uint8_t rhport) -{ - USB_OTG_GlobalTypeDef * usb_otg = GLOBAL_BASE(rhport); - USB_OTG_DeviceTypeDef * dev = DEVICE_BASE(rhport); - USB_OTG_OUTEndpointTypeDef * out_ep = OUT_EP_BASE(rhport); - USB_OTG_INEndpointTypeDef * in_ep = IN_EP_BASE(rhport); - - uint32_t const int_status = usb_otg->GINTSTS & usb_otg->GINTMSK; - - if(int_status & USB_OTG_GINTSTS_USBRST) - { - // USBRST is start of reset. - usb_otg->GINTSTS = USB_OTG_GINTSTS_USBRST; - bus_reset(rhport); - } - - if(int_status & USB_OTG_GINTSTS_ENUMDNE) - { - // ENUMDNE is the end of reset where speed of the link is detected - - usb_otg->GINTSTS = USB_OTG_GINTSTS_ENUMDNE; - - tusb_speed_t const speed = get_speed(rhport); - - set_turnaround(usb_otg, speed); - dcd_event_bus_reset(rhport, speed, true); - } - - if(int_status & USB_OTG_GINTSTS_USBSUSP) - { - usb_otg->GINTSTS = USB_OTG_GINTSTS_USBSUSP; - dcd_event_bus_signal(rhport, DCD_EVENT_SUSPEND, true); - } - - if(int_status & USB_OTG_GINTSTS_WKUINT) - { - usb_otg->GINTSTS = USB_OTG_GINTSTS_WKUINT; - dcd_event_bus_signal(rhport, DCD_EVENT_RESUME, true); - } - - // TODO check USB_OTG_GINTSTS_DISCINT for disconnect detection - // if(int_status & USB_OTG_GINTSTS_DISCINT) - - if(int_status & USB_OTG_GINTSTS_OTGINT) - { - // OTG INT bit is read-only - uint32_t const otg_int = usb_otg->GOTGINT; - - if (otg_int & USB_OTG_GOTGINT_SEDET) - { - dcd_event_bus_signal(rhport, DCD_EVENT_UNPLUGGED, true); - } - - usb_otg->GOTGINT = otg_int; - } - - if(int_status & USB_OTG_GINTSTS_SOF) - { - usb_otg->GINTSTS = USB_OTG_GINTSTS_SOF; - - // Disable SOF interrupt since currently only used for remote wakeup detection - usb_otg->GINTMSK &= ~USB_OTG_GINTMSK_SOFM; - - dcd_event_bus_signal(rhport, DCD_EVENT_SOF, true); - } - - // RxFIFO non-empty interrupt handling. - if(int_status & USB_OTG_GINTSTS_RXFLVL) - { - // RXFLVL bit is read-only - - // Mask out RXFLVL while reading data from FIFO - usb_otg->GINTMSK &= ~USB_OTG_GINTMSK_RXFLVLM; - - // Loop until all available packets were handled - do - { - handle_rxflvl_ints(rhport, out_ep); - } while(usb_otg->GINTSTS & USB_OTG_GINTSTS_RXFLVL); - - // Manage RX FIFO size - if (_out_ep_closed) - { - update_grxfsiz(rhport); - - // Disable flag - _out_ep_closed = false; - } - - usb_otg->GINTMSK |= USB_OTG_GINTMSK_RXFLVLM; - } - - // OUT endpoint interrupt handling. - if(int_status & USB_OTG_GINTSTS_OEPINT) - { - // OEPINT is read-only - handle_epout_ints(rhport, dev, out_ep); - } - - // IN endpoint interrupt handling. - if(int_status & USB_OTG_GINTSTS_IEPINT) - { - // IEPINT bit read-only - handle_epin_ints(rhport, dev, in_ep); - } - - // // Check for Incomplete isochronous IN transfer - // if(int_status & USB_OTG_GINTSTS_IISOIXFR) { - // printf(" IISOIXFR!\r\n"); - //// TU_LOG2(" IISOIXFR!\r\n"); - // } -} - -#endif diff --git a/src/portable/st/synopsys/synopsys_common.h b/src/portable/st/synopsys/synopsys_common.h deleted file mode 100644 index ce3195b23..000000000 --- a/src/portable/st/synopsys/synopsys_common.h +++ /dev/null @@ -1,1465 +0,0 @@ -/** - ****************************************************************************** - * @file synopsys_common.h - * @author MCD Application Team - * @brief CMSIS Cortex-M3 Device USB OTG peripheral Header File. - * This file contains the USB OTG peripheral register's definitions, bits - * definitions and memory mapping for STM32F1xx devices. - * - * This file contains: - * - Data structures and the address mapping for the USB OTG peripheral - * - The Peripheral's registers declarations and bits definition - * - Macros to access the peripheral's registers hardware - * - ****************************************************************************** - * @attention - * - *

© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.

- * - * This software component is licensed by ST under BSD 3-Clause license, - * the "License"; You may not use this file except in compliance with the - * License. You may obtain a copy of the License at: - * opensource.org/licenses/BSD-3-Clause - * - ****************************************************************************** - */ - -#include "stdint.h" - -#pragma once - -#ifdef __cplusplus - #define __I volatile -#else - #define __I volatile const -#endif -#define __O volatile -#define __IO volatile -#define __IM volatile const -#define __OM volatile -#define __IOM volatile - -/** - * @brief __USB_OTG_Core_register - */ - -typedef struct -{ - __IO uint32_t GOTGCTL; /*!< USB_OTG Control and Status Register Address offset: 000h */ - __IO uint32_t GOTGINT; /*!< USB_OTG Interrupt Register Address offset: 004h */ - __IO uint32_t GAHBCFG; /*!< Core AHB Configuration Register Address offset: 008h */ - __IO uint32_t GUSBCFG; /*!< Core USB Configuration Register Address offset: 00Ch */ - __IO uint32_t GRSTCTL; /*!< Core Reset Register Address offset: 010h */ - __IO uint32_t GINTSTS; /*!< Core Interrupt Register Address offset: 014h */ - __IO uint32_t GINTMSK; /*!< Core Interrupt Mask Register Address offset: 018h */ - __IO uint32_t GRXSTSR; /*!< Receive Sts Q Read Register Address offset: 01Ch */ - __IO uint32_t GRXSTSP; /*!< Receive Sts Q Read & POP Register Address offset: 020h */ - __IO uint32_t GRXFSIZ; /*!< Receive FIFO Size Register Address offset: 024h */ - __IO uint32_t DIEPTXF0_HNPTXFSIZ; /*!< EP0 / Non Periodic Tx FIFO Size Register Address offset: 028h */ - __IO uint32_t HNPTXSTS; /*!< Non Periodic Tx FIFO/Queue Sts reg Address offset: 02Ch */ - uint32_t Reserved30[2]; /*!< Reserved 030h*/ - __IO uint32_t GCCFG; /*!< General Purpose IO Register Address offset: 038h */ - __IO uint32_t CID; /*!< User ID Register Address offset: 03Ch */ - uint32_t Reserved40[48]; /*!< Reserved 040h-0FFh */ - __IO uint32_t HPTXFSIZ; /*!< Host Periodic Tx FIFO Size Reg Address offset: 100h */ - __IO uint32_t DIEPTXF[0x0F]; /*!< dev Periodic Transmit FIFO Address offset: 0x104 */ -} USB_OTG_GlobalTypeDef; - -/** - * @brief __device_Registers - */ - -typedef struct -{ - __IO uint32_t DCFG; /*!< dev Configuration Register Address offset: 800h*/ - __IO uint32_t DCTL; /*!< dev Control Register Address offset: 804h*/ - __IO uint32_t DSTS; /*!< dev Status Register (RO) Address offset: 808h*/ - uint32_t Reserved0C; /*!< Reserved 80Ch*/ - __IO uint32_t DIEPMSK; /*!< dev IN Endpoint Mask Address offset: 810h*/ - __IO uint32_t DOEPMSK; /*!< dev OUT Endpoint Mask Address offset: 814h*/ - __IO uint32_t DAINT; /*!< dev All Endpoints Itr Reg Address offset: 818h*/ - __IO uint32_t DAINTMSK; /*!< dev All Endpoints Itr Mask Address offset: 81Ch*/ - uint32_t Reserved20; /*!< Reserved 820h*/ - uint32_t Reserved9; /*!< Reserved 824h*/ - __IO uint32_t DVBUSDIS; /*!< dev VBUS discharge Register Address offset: 828h*/ - __IO uint32_t DVBUSPULSE; /*!< dev VBUS Pulse Register Address offset: 82Ch*/ - __IO uint32_t DTHRCTL; /*!< dev thr Address offset: 830h*/ - __IO uint32_t DIEPEMPMSK; /*!< dev empty msk Address offset: 834h*/ - __IO uint32_t DEACHINT; /*!< dedicated EP interrupt Address offset: 838h*/ - __IO uint32_t DEACHMSK; /*!< dedicated EP msk Address offset: 83Ch*/ - uint32_t Reserved40; /*!< dedicated EP mask Address offset: 840h*/ - __IO uint32_t DINEP1MSK; /*!< dedicated EP mask Address offset: 844h*/ - uint32_t Reserved44[15]; /*!< Reserved 844-87Ch*/ - __IO uint32_t DOUTEP1MSK; /*!< dedicated EP msk Address offset: 884h*/ -} USB_OTG_DeviceTypeDef; - -/** - * @brief __IN_Endpoint-Specific_Register - */ - -typedef struct -{ - __IO uint32_t DIEPCTL; /*!< dev IN Endpoint Control Reg 900h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /*!< Reserved 900h + (ep_num * 20h) + 04h*/ - __IO uint32_t DIEPINT; /*!< dev IN Endpoint Itr Reg 900h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /*!< Reserved 900h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DIEPTSIZ; /*!< IN Endpoint Txfer Size 900h + (ep_num * 20h) + 10h*/ - __IO uint32_t DIEPDMA; /*!< IN Endpoint DMA Address Reg 900h + (ep_num * 20h) + 14h*/ - __IO uint32_t DTXFSTS; /*!< IN Endpoint Tx FIFO Status Reg 900h + (ep_num * 20h) + 18h*/ - uint32_t Reserved18; /*!< Reserved 900h+(ep_num*20h)+1Ch-900h+ (ep_num * 20h) + 1Ch*/ -} USB_OTG_INEndpointTypeDef; - -/** - * @brief __OUT_Endpoint-Specific_Registers - */ - -typedef struct -{ - __IO uint32_t DOEPCTL; /*!< dev OUT Endpoint Control Reg B00h + (ep_num * 20h) + 00h*/ - uint32_t Reserved04; /*!< Reserved B00h + (ep_num * 20h) + 04h*/ - __IO uint32_t DOEPINT; /*!< dev OUT Endpoint Itr Reg B00h + (ep_num * 20h) + 08h*/ - uint32_t Reserved0C; /*!< Reserved B00h + (ep_num * 20h) + 0Ch*/ - __IO uint32_t DOEPTSIZ; /*!< dev OUT Endpoint Txfer Size B00h + (ep_num * 20h) + 10h*/ - __IO uint32_t DOEPDMA; /*!< dev OUT Endpoint DMA Address B00h + (ep_num * 20h) + 14h*/ - uint32_t Reserved18[2]; /*!< Reserved B00h + (ep_num * 20h) + 18h - B00h + (ep_num * 20h) + 1Ch*/ -} USB_OTG_OUTEndpointTypeDef; - -/** - * @brief __Host_Mode_Register_Structures - */ - -typedef struct -{ - __IO uint32_t HCFG; /*!< Host Configuration Register 400h*/ - __IO uint32_t HFIR; /*!< Host Frame Interval Register 404h*/ - __IO uint32_t HFNUM; /*!< Host Frame Nbr/Frame Remaining 408h*/ - uint32_t Reserved40C; /*!< Reserved 40Ch*/ - __IO uint32_t HPTXSTS; /*!< Host Periodic Tx FIFO/ Queue Status 410h*/ - __IO uint32_t HAINT; /*!< Host All Channels Interrupt Register 414h*/ - __IO uint32_t HAINTMSK; /*!< Host All Channels Interrupt Mask 418h*/ -} USB_OTG_HostTypeDef; - -/** - * @brief __Host_Channel_Specific_Registers - */ - -typedef struct -{ - __IO uint32_t HCCHAR; - __IO uint32_t HCSPLT; - __IO uint32_t HCINT; - __IO uint32_t HCINTMSK; - __IO uint32_t HCTSIZ; - __IO uint32_t HCDMA; - uint32_t Reserved[2]; -} USB_OTG_HostChannelTypeDef; - -/*!< USB registers base address */ -#define USB_OTG_FS_PERIPH_BASE 0x50000000UL - -#define USB_OTG_GLOBAL_BASE 0x00000000UL -#define USB_OTG_DEVICE_BASE 0x00000800UL -#define USB_OTG_IN_ENDPOINT_BASE 0x00000900UL -#define USB_OTG_OUT_ENDPOINT_BASE 0x00000B00UL -#define USB_OTG_EP_REG_SIZE 0x00000020UL -#define USB_OTG_HOST_BASE 0x00000400UL -#define USB_OTG_HOST_PORT_BASE 0x00000440UL -#define USB_OTG_HOST_CHANNEL_BASE 0x00000500UL -#define USB_OTG_HOST_CHANNEL_SIZE 0x00000020UL -#define USB_OTG_PCGCCTL_BASE 0x00000E00UL -#define USB_OTG_FIFO_BASE 0x00001000UL -#define USB_OTG_FIFO_SIZE 0x00001000UL - -/******************************************************************************/ -/* */ -/* USB_OTG */ -/* */ -/******************************************************************************/ -/******************** Bit definition for USB_OTG_GOTGCTL register ***********/ -#define USB_OTG_GOTGCTL_SRQSCS_Pos (0U) -#define USB_OTG_GOTGCTL_SRQSCS_Msk (0x1UL << USB_OTG_GOTGCTL_SRQSCS_Pos) /*!< 0x00000001 */ -#define USB_OTG_GOTGCTL_SRQSCS USB_OTG_GOTGCTL_SRQSCS_Msk /*!< Session request success */ -#define USB_OTG_GOTGCTL_SRQ_Pos (1U) -#define USB_OTG_GOTGCTL_SRQ_Msk (0x1UL << USB_OTG_GOTGCTL_SRQ_Pos) /*!< 0x00000002 */ -#define USB_OTG_GOTGCTL_SRQ USB_OTG_GOTGCTL_SRQ_Msk /*!< Session request */ -#define USB_OTG_GOTGCTL_HNGSCS_Pos (8U) -#define USB_OTG_GOTGCTL_HNGSCS_Msk (0x1UL << USB_OTG_GOTGCTL_HNGSCS_Pos) /*!< 0x00000100 */ -#define USB_OTG_GOTGCTL_HNGSCS USB_OTG_GOTGCTL_HNGSCS_Msk /*!< Host set HNP enable */ -#define USB_OTG_GOTGCTL_HNPRQ_Pos (9U) -#define USB_OTG_GOTGCTL_HNPRQ_Msk (0x1UL << USB_OTG_GOTGCTL_HNPRQ_Pos) /*!< 0x00000200 */ -#define USB_OTG_GOTGCTL_HNPRQ USB_OTG_GOTGCTL_HNPRQ_Msk /*!< HNP request */ -#define USB_OTG_GOTGCTL_HSHNPEN_Pos (10U) -#define USB_OTG_GOTGCTL_HSHNPEN_Msk (0x1UL << USB_OTG_GOTGCTL_HSHNPEN_Pos) /*!< 0x00000400 */ -#define USB_OTG_GOTGCTL_HSHNPEN USB_OTG_GOTGCTL_HSHNPEN_Msk /*!< Host set HNP enable */ -#define USB_OTG_GOTGCTL_DHNPEN_Pos (11U) -#define USB_OTG_GOTGCTL_DHNPEN_Msk (0x1UL << USB_OTG_GOTGCTL_DHNPEN_Pos) /*!< 0x00000800 */ -#define USB_OTG_GOTGCTL_DHNPEN USB_OTG_GOTGCTL_DHNPEN_Msk /*!< Device HNP enabled */ -#define USB_OTG_GOTGCTL_CIDSTS_Pos (16U) -#define USB_OTG_GOTGCTL_CIDSTS_Msk (0x1UL << USB_OTG_GOTGCTL_CIDSTS_Pos) /*!< 0x00010000 */ -#define USB_OTG_GOTGCTL_CIDSTS USB_OTG_GOTGCTL_CIDSTS_Msk /*!< Connector ID status */ -#define USB_OTG_GOTGCTL_DBCT_Pos (17U) -#define USB_OTG_GOTGCTL_DBCT_Msk (0x1UL << USB_OTG_GOTGCTL_DBCT_Pos) /*!< 0x00020000 */ -#define USB_OTG_GOTGCTL_DBCT USB_OTG_GOTGCTL_DBCT_Msk /*!< Long/short debounce time */ -#define USB_OTG_GOTGCTL_ASVLD_Pos (18U) -#define USB_OTG_GOTGCTL_ASVLD_Msk (0x1UL << USB_OTG_GOTGCTL_ASVLD_Pos) /*!< 0x00040000 */ -#define USB_OTG_GOTGCTL_ASVLD USB_OTG_GOTGCTL_ASVLD_Msk /*!< A-session valid */ -#define USB_OTG_GOTGCTL_BSVLD_Pos (19U) -#define USB_OTG_GOTGCTL_BSVLD_Msk (0x1UL << USB_OTG_GOTGCTL_BSVLD_Pos) /*!< 0x00080000 */ -#define USB_OTG_GOTGCTL_BSVLD USB_OTG_GOTGCTL_BSVLD_Msk /*!< B-session valid */ - -/******************** Bit definition for USB_OTG_HCFG register ********************/ - -#define USB_OTG_HCFG_FSLSPCS_Pos (0U) -#define USB_OTG_HCFG_FSLSPCS_Msk (0x3UL << USB_OTG_HCFG_FSLSPCS_Pos) /*!< 0x00000003 */ -#define USB_OTG_HCFG_FSLSPCS USB_OTG_HCFG_FSLSPCS_Msk /*!< FS/LS PHY clock select */ -#define USB_OTG_HCFG_FSLSPCS_0 (0x1UL << USB_OTG_HCFG_FSLSPCS_Pos) /*!< 0x00000001 */ -#define USB_OTG_HCFG_FSLSPCS_1 (0x2UL << USB_OTG_HCFG_FSLSPCS_Pos) /*!< 0x00000002 */ -#define USB_OTG_HCFG_FSLSS_Pos (2U) -#define USB_OTG_HCFG_FSLSS_Msk (0x1UL << USB_OTG_HCFG_FSLSS_Pos) /*!< 0x00000004 */ -#define USB_OTG_HCFG_FSLSS USB_OTG_HCFG_FSLSS_Msk /*!< FS- and LS-only support */ - -/******************** Bit definition for USB_OTG_DCFG register ********************/ - -#define USB_OTG_DCFG_DSPD_Pos (0U) -#define USB_OTG_DCFG_DSPD_Msk (0x3UL << USB_OTG_DCFG_DSPD_Pos) /*!< 0x00000003 */ -#define USB_OTG_DCFG_DSPD USB_OTG_DCFG_DSPD_Msk /*!< Device speed */ -#define USB_OTG_DCFG_DSPD_0 (0x1UL << USB_OTG_DCFG_DSPD_Pos) /*!< 0x00000001 */ -#define USB_OTG_DCFG_DSPD_1 (0x2UL << USB_OTG_DCFG_DSPD_Pos) /*!< 0x00000002 */ -#define USB_OTG_DCFG_NZLSOHSK_Pos (2U) -#define USB_OTG_DCFG_NZLSOHSK_Msk (0x1UL << USB_OTG_DCFG_NZLSOHSK_Pos) /*!< 0x00000004 */ -#define USB_OTG_DCFG_NZLSOHSK USB_OTG_DCFG_NZLSOHSK_Msk /*!< Nonzero-length status OUT handshake */ - -#define USB_OTG_DCFG_DAD_Pos (4U) -#define USB_OTG_DCFG_DAD_Msk (0x7FUL << USB_OTG_DCFG_DAD_Pos) /*!< 0x000007F0 */ -#define USB_OTG_DCFG_DAD USB_OTG_DCFG_DAD_Msk /*!< Device address */ -#define USB_OTG_DCFG_DAD_0 (0x01UL << USB_OTG_DCFG_DAD_Pos) /*!< 0x00000010 */ -#define USB_OTG_DCFG_DAD_1 (0x02UL << USB_OTG_DCFG_DAD_Pos) /*!< 0x00000020 */ -#define USB_OTG_DCFG_DAD_2 (0x04UL << USB_OTG_DCFG_DAD_Pos) /*!< 0x00000040 */ -#define USB_OTG_DCFG_DAD_3 (0x08UL << USB_OTG_DCFG_DAD_Pos) /*!< 0x00000080 */ -#define USB_OTG_DCFG_DAD_4 (0x10UL << USB_OTG_DCFG_DAD_Pos) /*!< 0x00000100 */ -#define USB_OTG_DCFG_DAD_5 (0x20UL << USB_OTG_DCFG_DAD_Pos) /*!< 0x00000200 */ -#define USB_OTG_DCFG_DAD_6 (0x40UL << USB_OTG_DCFG_DAD_Pos) /*!< 0x00000400 */ - -#define USB_OTG_DCFG_PFIVL_Pos (11U) -#define USB_OTG_DCFG_PFIVL_Msk (0x3UL << USB_OTG_DCFG_PFIVL_Pos) /*!< 0x00001800 */ -#define USB_OTG_DCFG_PFIVL USB_OTG_DCFG_PFIVL_Msk /*!< Periodic (micro)frame interval */ -#define USB_OTG_DCFG_PFIVL_0 (0x1UL << USB_OTG_DCFG_PFIVL_Pos) /*!< 0x00000800 */ -#define USB_OTG_DCFG_PFIVL_1 (0x2UL << USB_OTG_DCFG_PFIVL_Pos) /*!< 0x00001000 */ - -#define USB_OTG_DCFG_PERSCHIVL_Pos (24U) -#define USB_OTG_DCFG_PERSCHIVL_Msk (0x3UL << USB_OTG_DCFG_PERSCHIVL_Pos) /*!< 0x03000000 */ -#define USB_OTG_DCFG_PERSCHIVL USB_OTG_DCFG_PERSCHIVL_Msk /*!< Periodic scheduling interval */ -#define USB_OTG_DCFG_PERSCHIVL_0 (0x1UL << USB_OTG_DCFG_PERSCHIVL_Pos) /*!< 0x01000000 */ -#define USB_OTG_DCFG_PERSCHIVL_1 (0x2UL << USB_OTG_DCFG_PERSCHIVL_Pos) /*!< 0x02000000 */ - -/******************** Bit definition for USB_OTG_PCGCR register ********************/ -#define USB_OTG_PCGCR_STPPCLK_Pos (0U) -#define USB_OTG_PCGCR_STPPCLK_Msk (0x1UL << USB_OTG_PCGCR_STPPCLK_Pos) /*!< 0x00000001 */ -#define USB_OTG_PCGCR_STPPCLK USB_OTG_PCGCR_STPPCLK_Msk /*!< Stop PHY clock */ -#define USB_OTG_PCGCR_GATEHCLK_Pos (1U) -#define USB_OTG_PCGCR_GATEHCLK_Msk (0x1UL << USB_OTG_PCGCR_GATEHCLK_Pos) /*!< 0x00000002 */ -#define USB_OTG_PCGCR_GATEHCLK USB_OTG_PCGCR_GATEHCLK_Msk /*!< Gate HCLK */ -#define USB_OTG_PCGCR_PHYSUSP_Pos (4U) -#define USB_OTG_PCGCR_PHYSUSP_Msk (0x1UL << USB_OTG_PCGCR_PHYSUSP_Pos) /*!< 0x00000010 */ -#define USB_OTG_PCGCR_PHYSUSP USB_OTG_PCGCR_PHYSUSP_Msk /*!< PHY suspended */ - -/******************** Bit definition for USB_OTG_GOTGINT register ********************/ -#define USB_OTG_GOTGINT_SEDET_Pos (2U) -#define USB_OTG_GOTGINT_SEDET_Msk (0x1UL << USB_OTG_GOTGINT_SEDET_Pos) /*!< 0x00000004 */ -#define USB_OTG_GOTGINT_SEDET USB_OTG_GOTGINT_SEDET_Msk /*!< Session end detected */ -#define USB_OTG_GOTGINT_SRSSCHG_Pos (8U) -#define USB_OTG_GOTGINT_SRSSCHG_Msk (0x1UL << USB_OTG_GOTGINT_SRSSCHG_Pos) /*!< 0x00000100 */ -#define USB_OTG_GOTGINT_SRSSCHG USB_OTG_GOTGINT_SRSSCHG_Msk /*!< Session request success status change */ -#define USB_OTG_GOTGINT_HNSSCHG_Pos (9U) -#define USB_OTG_GOTGINT_HNSSCHG_Msk (0x1UL << USB_OTG_GOTGINT_HNSSCHG_Pos) /*!< 0x00000200 */ -#define USB_OTG_GOTGINT_HNSSCHG USB_OTG_GOTGINT_HNSSCHG_Msk /*!< Host negotiation success status change */ -#define USB_OTG_GOTGINT_HNGDET_Pos (17U) -#define USB_OTG_GOTGINT_HNGDET_Msk (0x1UL << USB_OTG_GOTGINT_HNGDET_Pos) /*!< 0x00020000 */ -#define USB_OTG_GOTGINT_HNGDET USB_OTG_GOTGINT_HNGDET_Msk /*!< Host negotiation detected */ -#define USB_OTG_GOTGINT_ADTOCHG_Pos (18U) -#define USB_OTG_GOTGINT_ADTOCHG_Msk (0x1UL << USB_OTG_GOTGINT_ADTOCHG_Pos) /*!< 0x00040000 */ -#define USB_OTG_GOTGINT_ADTOCHG USB_OTG_GOTGINT_ADTOCHG_Msk /*!< A-device timeout change */ -#define USB_OTG_GOTGINT_DBCDNE_Pos (19U) -#define USB_OTG_GOTGINT_DBCDNE_Msk (0x1UL << USB_OTG_GOTGINT_DBCDNE_Pos) /*!< 0x00080000 */ -#define USB_OTG_GOTGINT_DBCDNE USB_OTG_GOTGINT_DBCDNE_Msk /*!< Debounce done */ - -/******************** Bit definition for USB_OTG_DCTL register ********************/ -#define USB_OTG_DCTL_RWUSIG_Pos (0U) -#define USB_OTG_DCTL_RWUSIG_Msk (0x1UL << USB_OTG_DCTL_RWUSIG_Pos) /*!< 0x00000001 */ -#define USB_OTG_DCTL_RWUSIG USB_OTG_DCTL_RWUSIG_Msk /*!< Remote wakeup signaling */ -#define USB_OTG_DCTL_SDIS_Pos (1U) -#define USB_OTG_DCTL_SDIS_Msk (0x1UL << USB_OTG_DCTL_SDIS_Pos) /*!< 0x00000002 */ -#define USB_OTG_DCTL_SDIS USB_OTG_DCTL_SDIS_Msk /*!< Soft disconnect */ -#define USB_OTG_DCTL_GINSTS_Pos (2U) -#define USB_OTG_DCTL_GINSTS_Msk (0x1UL << USB_OTG_DCTL_GINSTS_Pos) /*!< 0x00000004 */ -#define USB_OTG_DCTL_GINSTS USB_OTG_DCTL_GINSTS_Msk /*!< Global IN NAK status */ -#define USB_OTG_DCTL_GONSTS_Pos (3U) -#define USB_OTG_DCTL_GONSTS_Msk (0x1UL << USB_OTG_DCTL_GONSTS_Pos) /*!< 0x00000008 */ -#define USB_OTG_DCTL_GONSTS USB_OTG_DCTL_GONSTS_Msk /*!< Global OUT NAK status */ - -#define USB_OTG_DCTL_TCTL_Pos (4U) -#define USB_OTG_DCTL_TCTL_Msk (0x7UL << USB_OTG_DCTL_TCTL_Pos) /*!< 0x00000070 */ -#define USB_OTG_DCTL_TCTL USB_OTG_DCTL_TCTL_Msk /*!< Test control */ -#define USB_OTG_DCTL_TCTL_0 (0x1UL << USB_OTG_DCTL_TCTL_Pos) /*!< 0x00000010 */ -#define USB_OTG_DCTL_TCTL_1 (0x2UL << USB_OTG_DCTL_TCTL_Pos) /*!< 0x00000020 */ -#define USB_OTG_DCTL_TCTL_2 (0x4UL << USB_OTG_DCTL_TCTL_Pos) /*!< 0x00000040 */ -#define USB_OTG_DCTL_SGINAK_Pos (7U) -#define USB_OTG_DCTL_SGINAK_Msk (0x1UL << USB_OTG_DCTL_SGINAK_Pos) /*!< 0x00000080 */ -#define USB_OTG_DCTL_SGINAK USB_OTG_DCTL_SGINAK_Msk /*!< Set global IN NAK */ -#define USB_OTG_DCTL_CGINAK_Pos (8U) -#define USB_OTG_DCTL_CGINAK_Msk (0x1UL << USB_OTG_DCTL_CGINAK_Pos) /*!< 0x00000100 */ -#define USB_OTG_DCTL_CGINAK USB_OTG_DCTL_CGINAK_Msk /*!< Clear global IN NAK */ -#define USB_OTG_DCTL_SGONAK_Pos (9U) -#define USB_OTG_DCTL_SGONAK_Msk (0x1UL << USB_OTG_DCTL_SGONAK_Pos) /*!< 0x00000200 */ -#define USB_OTG_DCTL_SGONAK USB_OTG_DCTL_SGONAK_Msk /*!< Set global OUT NAK */ -#define USB_OTG_DCTL_CGONAK_Pos (10U) -#define USB_OTG_DCTL_CGONAK_Msk (0x1UL << USB_OTG_DCTL_CGONAK_Pos) /*!< 0x00000400 */ -#define USB_OTG_DCTL_CGONAK USB_OTG_DCTL_CGONAK_Msk /*!< Clear global OUT NAK */ -#define USB_OTG_DCTL_POPRGDNE_Pos (11U) -#define USB_OTG_DCTL_POPRGDNE_Msk (0x1UL << USB_OTG_DCTL_POPRGDNE_Pos) /*!< 0x00000800 */ -#define USB_OTG_DCTL_POPRGDNE USB_OTG_DCTL_POPRGDNE_Msk /*!< Power-on programming done */ - -/******************** Bit definition for USB_OTG_HFIR register ********************/ -#define USB_OTG_HFIR_FRIVL_Pos (0U) -#define USB_OTG_HFIR_FRIVL_Msk (0xFFFFUL << USB_OTG_HFIR_FRIVL_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_HFIR_FRIVL USB_OTG_HFIR_FRIVL_Msk /*!< Frame interval */ - -/******************** Bit definition for USB_OTG_HFNUM register ********************/ -#define USB_OTG_HFNUM_FRNUM_Pos (0U) -#define USB_OTG_HFNUM_FRNUM_Msk (0xFFFFUL << USB_OTG_HFNUM_FRNUM_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_HFNUM_FRNUM USB_OTG_HFNUM_FRNUM_Msk /*!< Frame number */ -#define USB_OTG_HFNUM_FTREM_Pos (16U) -#define USB_OTG_HFNUM_FTREM_Msk (0xFFFFUL << USB_OTG_HFNUM_FTREM_Pos) /*!< 0xFFFF0000 */ -#define USB_OTG_HFNUM_FTREM USB_OTG_HFNUM_FTREM_Msk /*!< Frame time remaining */ - -/******************** Bit definition for USB_OTG_DSTS register ********************/ -#define USB_OTG_DSTS_SUSPSTS_Pos (0U) -#define USB_OTG_DSTS_SUSPSTS_Msk (0x1UL << USB_OTG_DSTS_SUSPSTS_Pos) /*!< 0x00000001 */ -#define USB_OTG_DSTS_SUSPSTS USB_OTG_DSTS_SUSPSTS_Msk /*!< Suspend status */ - -#define USB_OTG_DSTS_ENUMSPD_Pos (1U) -#define USB_OTG_DSTS_ENUMSPD_Msk (0x3UL << USB_OTG_DSTS_ENUMSPD_Pos) /*!< 0x00000006 */ -#define USB_OTG_DSTS_ENUMSPD USB_OTG_DSTS_ENUMSPD_Msk /*!< Enumerated speed */ -#define USB_OTG_DSTS_ENUMSPD_0 (0x1UL << USB_OTG_DSTS_ENUMSPD_Pos) /*!< 0x00000002 */ -#define USB_OTG_DSTS_ENUMSPD_1 (0x2UL << USB_OTG_DSTS_ENUMSPD_Pos) /*!< 0x00000004 */ -#define USB_OTG_DSTS_EERR_Pos (3U) -#define USB_OTG_DSTS_EERR_Msk (0x1UL << USB_OTG_DSTS_EERR_Pos) /*!< 0x00000008 */ -#define USB_OTG_DSTS_EERR USB_OTG_DSTS_EERR_Msk /*!< Erratic error */ -#define USB_OTG_DSTS_FNSOF_Pos (8U) -#define USB_OTG_DSTS_FNSOF_Msk (0x3FFFUL << USB_OTG_DSTS_FNSOF_Pos) /*!< 0x003FFF00 */ -#define USB_OTG_DSTS_FNSOF USB_OTG_DSTS_FNSOF_Msk /*!< Frame number of the received SOF */ - -/******************** Bit definition for USB_OTG_GAHBCFG register ********************/ -#define USB_OTG_GAHBCFG_GINT_Pos (0U) -#define USB_OTG_GAHBCFG_GINT_Msk (0x1UL << USB_OTG_GAHBCFG_GINT_Pos) /*!< 0x00000001 */ -#define USB_OTG_GAHBCFG_GINT USB_OTG_GAHBCFG_GINT_Msk /*!< Global interrupt mask */ -#define USB_OTG_GAHBCFG_HBSTLEN_Pos (1U) -#define USB_OTG_GAHBCFG_HBSTLEN_Msk (0xFUL << USB_OTG_GAHBCFG_HBSTLEN_Pos) /*!< 0x0000001E */ -#define USB_OTG_GAHBCFG_HBSTLEN USB_OTG_GAHBCFG_HBSTLEN_Msk /*!< Burst length/type */ -#define USB_OTG_GAHBCFG_HBSTLEN_0 (0x0UL << USB_OTG_GAHBCFG_HBSTLEN_Pos) /*!< Single */ -#define USB_OTG_GAHBCFG_HBSTLEN_1 (0x1UL << USB_OTG_GAHBCFG_HBSTLEN_Pos) /*!< INCR */ -#define USB_OTG_GAHBCFG_HBSTLEN_2 (0x3UL << USB_OTG_GAHBCFG_HBSTLEN_Pos) /*!< INCR4 */ -#define USB_OTG_GAHBCFG_HBSTLEN_3 (0x5UL << USB_OTG_GAHBCFG_HBSTLEN_Pos) /*!< INCR8 */ -#define USB_OTG_GAHBCFG_HBSTLEN_4 (0x7UL << USB_OTG_GAHBCFG_HBSTLEN_Pos) /*!< INCR16 */ -#define USB_OTG_GAHBCFG_DMAEN_Pos (5U) -#define USB_OTG_GAHBCFG_DMAEN_Msk (0x1UL << USB_OTG_GAHBCFG_DMAEN_Pos) /*!< 0x00000020 */ -#define USB_OTG_GAHBCFG_DMAEN USB_OTG_GAHBCFG_DMAEN_Msk /*!< DMA enable */ -#define USB_OTG_GAHBCFG_TXFELVL_Pos (7U) -#define USB_OTG_GAHBCFG_TXFELVL_Msk (0x1UL << USB_OTG_GAHBCFG_TXFELVL_Pos) /*!< 0x00000080 */ -#define USB_OTG_GAHBCFG_TXFELVL USB_OTG_GAHBCFG_TXFELVL_Msk /*!< TxFIFO empty level */ -#define USB_OTG_GAHBCFG_PTXFELVL_Pos (8U) -#define USB_OTG_GAHBCFG_PTXFELVL_Msk (0x1UL << USB_OTG_GAHBCFG_PTXFELVL_Pos) /*!< 0x00000100 */ -#define USB_OTG_GAHBCFG_PTXFELVL USB_OTG_GAHBCFG_PTXFELVL_Msk /*!< Periodic TxFIFO empty level */ - -/******************** Bit definition for USB_OTG_GUSBCFG register ********************/ - -#define USB_OTG_GUSBCFG_TOCAL_Pos (0U) -#define USB_OTG_GUSBCFG_TOCAL_Msk (0x7UL << USB_OTG_GUSBCFG_TOCAL_Pos) /*!< 0x00000007 */ -#define USB_OTG_GUSBCFG_TOCAL USB_OTG_GUSBCFG_TOCAL_Msk /*!< FS timeout calibration */ -#define USB_OTG_GUSBCFG_TOCAL_0 (0x1UL << USB_OTG_GUSBCFG_TOCAL_Pos) /*!< 0x00000001 */ -#define USB_OTG_GUSBCFG_TOCAL_1 (0x2UL << USB_OTG_GUSBCFG_TOCAL_Pos) /*!< 0x00000002 */ -#define USB_OTG_GUSBCFG_TOCAL_2 (0x4UL << USB_OTG_GUSBCFG_TOCAL_Pos) /*!< 0x00000004 */ -#define USB_OTG_GUSBCFG_PHYSEL_Pos (6U) -#define USB_OTG_GUSBCFG_PHYSEL_Msk (0x1UL << USB_OTG_GUSBCFG_PHYSEL_Pos) /*!< 0x00000040 */ -#define USB_OTG_GUSBCFG_PHYSEL USB_OTG_GUSBCFG_PHYSEL_Msk /*!< USB 2.0 high-speed ULPI PHY or USB 1.1 full-speed serial transceiver select */ -#define USB_OTG_GUSBCFG_SRPCAP_Pos (8U) -#define USB_OTG_GUSBCFG_SRPCAP_Msk (0x1UL << USB_OTG_GUSBCFG_SRPCAP_Pos) /*!< 0x00000100 */ -#define USB_OTG_GUSBCFG_SRPCAP USB_OTG_GUSBCFG_SRPCAP_Msk /*!< SRP-capable */ -#define USB_OTG_GUSBCFG_HNPCAP_Pos (9U) -#define USB_OTG_GUSBCFG_HNPCAP_Msk (0x1UL << USB_OTG_GUSBCFG_HNPCAP_Pos) /*!< 0x00000200 */ -#define USB_OTG_GUSBCFG_HNPCAP USB_OTG_GUSBCFG_HNPCAP_Msk /*!< HNP-capable */ -#define USB_OTG_GUSBCFG_TRDT_Pos (10U) -#define USB_OTG_GUSBCFG_TRDT_Msk (0xFUL << USB_OTG_GUSBCFG_TRDT_Pos) /*!< 0x00003C00 */ -#define USB_OTG_GUSBCFG_TRDT USB_OTG_GUSBCFG_TRDT_Msk /*!< USB turnaround time */ -#define USB_OTG_GUSBCFG_TRDT_0 (0x1UL << USB_OTG_GUSBCFG_TRDT_Pos) /*!< 0x00000400 */ -#define USB_OTG_GUSBCFG_TRDT_1 (0x2UL << USB_OTG_GUSBCFG_TRDT_Pos) /*!< 0x00000800 */ -#define USB_OTG_GUSBCFG_TRDT_2 (0x4UL << USB_OTG_GUSBCFG_TRDT_Pos) /*!< 0x00001000 */ -#define USB_OTG_GUSBCFG_TRDT_3 (0x8UL << USB_OTG_GUSBCFG_TRDT_Pos) /*!< 0x00002000 */ -#define USB_OTG_GUSBCFG_PHYLPCS_Pos (15U) -#define USB_OTG_GUSBCFG_PHYLPCS_Msk (0x1UL << USB_OTG_GUSBCFG_PHYLPCS_Pos) /*!< 0x00008000 */ -#define USB_OTG_GUSBCFG_PHYLPCS USB_OTG_GUSBCFG_PHYLPCS_Msk /*!< PHY Low-power clock select */ -#define USB_OTG_GUSBCFG_ULPIFSLS_Pos (17U) -#define USB_OTG_GUSBCFG_ULPIFSLS_Msk (0x1UL << USB_OTG_GUSBCFG_ULPIFSLS_Pos) /*!< 0x00020000 */ -#define USB_OTG_GUSBCFG_ULPIFSLS USB_OTG_GUSBCFG_ULPIFSLS_Msk /*!< ULPI FS/LS select */ -#define USB_OTG_GUSBCFG_ULPIAR_Pos (18U) -#define USB_OTG_GUSBCFG_ULPIAR_Msk (0x1UL << USB_OTG_GUSBCFG_ULPIAR_Pos) /*!< 0x00040000 */ -#define USB_OTG_GUSBCFG_ULPIAR USB_OTG_GUSBCFG_ULPIAR_Msk /*!< ULPI Auto-resume */ -#define USB_OTG_GUSBCFG_ULPICSM_Pos (19U) -#define USB_OTG_GUSBCFG_ULPICSM_Msk (0x1UL << USB_OTG_GUSBCFG_ULPICSM_Pos) /*!< 0x00080000 */ -#define USB_OTG_GUSBCFG_ULPICSM USB_OTG_GUSBCFG_ULPICSM_Msk /*!< ULPI Clock SuspendM */ -#define USB_OTG_GUSBCFG_ULPIEVBUSD_Pos (20U) -#define USB_OTG_GUSBCFG_ULPIEVBUSD_Msk (0x1UL << USB_OTG_GUSBCFG_ULPIEVBUSD_Pos) /*!< 0x00100000 */ -#define USB_OTG_GUSBCFG_ULPIEVBUSD USB_OTG_GUSBCFG_ULPIEVBUSD_Msk /*!< ULPI External VBUS Drive */ -#define USB_OTG_GUSBCFG_ULPIEVBUSI_Pos (21U) -#define USB_OTG_GUSBCFG_ULPIEVBUSI_Msk (0x1UL << USB_OTG_GUSBCFG_ULPIEVBUSI_Pos) /*!< 0x00200000 */ -#define USB_OTG_GUSBCFG_ULPIEVBUSI USB_OTG_GUSBCFG_ULPIEVBUSI_Msk /*!< ULPI external VBUS indicator */ -#define USB_OTG_GUSBCFG_TSDPS_Pos (22U) -#define USB_OTG_GUSBCFG_TSDPS_Msk (0x1UL << USB_OTG_GUSBCFG_TSDPS_Pos) /*!< 0x00400000 */ -#define USB_OTG_GUSBCFG_TSDPS USB_OTG_GUSBCFG_TSDPS_Msk /*!< TermSel DLine pulsing selection */ -#define USB_OTG_GUSBCFG_PCCI_Pos (23U) -#define USB_OTG_GUSBCFG_PCCI_Msk (0x1UL << USB_OTG_GUSBCFG_PCCI_Pos) /*!< 0x00800000 */ -#define USB_OTG_GUSBCFG_PCCI USB_OTG_GUSBCFG_PCCI_Msk /*!< Indicator complement */ -#define USB_OTG_GUSBCFG_PTCI_Pos (24U) -#define USB_OTG_GUSBCFG_PTCI_Msk (0x1UL << USB_OTG_GUSBCFG_PTCI_Pos) /*!< 0x01000000 */ -#define USB_OTG_GUSBCFG_PTCI USB_OTG_GUSBCFG_PTCI_Msk /*!< Indicator pass through */ -#define USB_OTG_GUSBCFG_ULPIIPD_Pos (25U) -#define USB_OTG_GUSBCFG_ULPIIPD_Msk (0x1UL << USB_OTG_GUSBCFG_ULPIIPD_Pos) /*!< 0x02000000 */ -#define USB_OTG_GUSBCFG_ULPIIPD USB_OTG_GUSBCFG_ULPIIPD_Msk /*!< ULPI interface protect disable */ -#define USB_OTG_GUSBCFG_FHMOD_Pos (29U) -#define USB_OTG_GUSBCFG_FHMOD_Msk (0x1UL << USB_OTG_GUSBCFG_FHMOD_Pos) /*!< 0x20000000 */ -#define USB_OTG_GUSBCFG_FHMOD USB_OTG_GUSBCFG_FHMOD_Msk /*!< Forced host mode */ -#define USB_OTG_GUSBCFG_FDMOD_Pos (30U) -#define USB_OTG_GUSBCFG_FDMOD_Msk (0x1UL << USB_OTG_GUSBCFG_FDMOD_Pos) /*!< 0x40000000 */ -#define USB_OTG_GUSBCFG_FDMOD USB_OTG_GUSBCFG_FDMOD_Msk /*!< Forced peripheral mode */ -#define USB_OTG_GUSBCFG_CTXPKT_Pos (31U) -#define USB_OTG_GUSBCFG_CTXPKT_Msk (0x1UL << USB_OTG_GUSBCFG_CTXPKT_Pos) /*!< 0x80000000 */ -#define USB_OTG_GUSBCFG_CTXPKT USB_OTG_GUSBCFG_CTXPKT_Msk /*!< Corrupt Tx packet */ - -/******************** Bit definition for USB_OTG_GRSTCTL register ********************/ -#define USB_OTG_GRSTCTL_CSRST_Pos (0U) -#define USB_OTG_GRSTCTL_CSRST_Msk (0x1UL << USB_OTG_GRSTCTL_CSRST_Pos) /*!< 0x00000001 */ -#define USB_OTG_GRSTCTL_CSRST USB_OTG_GRSTCTL_CSRST_Msk /*!< Core soft reset */ -#define USB_OTG_GRSTCTL_HSRST_Pos (1U) -#define USB_OTG_GRSTCTL_HSRST_Msk (0x1UL << USB_OTG_GRSTCTL_HSRST_Pos) /*!< 0x00000002 */ -#define USB_OTG_GRSTCTL_HSRST USB_OTG_GRSTCTL_HSRST_Msk /*!< HCLK soft reset */ -#define USB_OTG_GRSTCTL_FCRST_Pos (2U) -#define USB_OTG_GRSTCTL_FCRST_Msk (0x1UL << USB_OTG_GRSTCTL_FCRST_Pos) /*!< 0x00000004 */ -#define USB_OTG_GRSTCTL_FCRST USB_OTG_GRSTCTL_FCRST_Msk /*!< Host frame counter reset */ -#define USB_OTG_GRSTCTL_RXFFLSH_Pos (4U) -#define USB_OTG_GRSTCTL_RXFFLSH_Msk (0x1UL << USB_OTG_GRSTCTL_RXFFLSH_Pos) /*!< 0x00000010 */ -#define USB_OTG_GRSTCTL_RXFFLSH USB_OTG_GRSTCTL_RXFFLSH_Msk /*!< RxFIFO flush */ -#define USB_OTG_GRSTCTL_TXFFLSH_Pos (5U) -#define USB_OTG_GRSTCTL_TXFFLSH_Msk (0x1UL << USB_OTG_GRSTCTL_TXFFLSH_Pos) /*!< 0x00000020 */ -#define USB_OTG_GRSTCTL_TXFFLSH USB_OTG_GRSTCTL_TXFFLSH_Msk /*!< TxFIFO flush */ - - -#define USB_OTG_GRSTCTL_TXFNUM_Pos (6U) -#define USB_OTG_GRSTCTL_TXFNUM_Msk (0x1FUL << USB_OTG_GRSTCTL_TXFNUM_Pos) /*!< 0x000007C0 */ -#define USB_OTG_GRSTCTL_TXFNUM USB_OTG_GRSTCTL_TXFNUM_Msk /*!< TxFIFO number */ -#define USB_OTG_GRSTCTL_TXFNUM_0 (0x01UL << USB_OTG_GRSTCTL_TXFNUM_Pos) /*!< 0x00000040 */ -#define USB_OTG_GRSTCTL_TXFNUM_1 (0x02UL << USB_OTG_GRSTCTL_TXFNUM_Pos) /*!< 0x00000080 */ -#define USB_OTG_GRSTCTL_TXFNUM_2 (0x04UL << USB_OTG_GRSTCTL_TXFNUM_Pos) /*!< 0x00000100 */ -#define USB_OTG_GRSTCTL_TXFNUM_3 (0x08UL << USB_OTG_GRSTCTL_TXFNUM_Pos) /*!< 0x00000200 */ -#define USB_OTG_GRSTCTL_TXFNUM_4 (0x10UL << USB_OTG_GRSTCTL_TXFNUM_Pos) /*!< 0x00000400 */ -#define USB_OTG_GRSTCTL_DMAREQ_Pos (30U) -#define USB_OTG_GRSTCTL_DMAREQ_Msk (0x1UL << USB_OTG_GRSTCTL_DMAREQ_Pos) /*!< 0x40000000 */ -#define USB_OTG_GRSTCTL_DMAREQ USB_OTG_GRSTCTL_DMAREQ_Msk /*!< DMA request signal */ -#define USB_OTG_GRSTCTL_AHBIDL_Pos (31U) -#define USB_OTG_GRSTCTL_AHBIDL_Msk (0x1UL << USB_OTG_GRSTCTL_AHBIDL_Pos) /*!< 0x80000000 */ -#define USB_OTG_GRSTCTL_AHBIDL USB_OTG_GRSTCTL_AHBIDL_Msk /*!< AHB master idle */ - -/******************** Bit definition for USB_OTG_DIEPMSK register ********************/ -#define USB_OTG_DIEPMSK_XFRCM_Pos (0U) -#define USB_OTG_DIEPMSK_XFRCM_Msk (0x1UL << USB_OTG_DIEPMSK_XFRCM_Pos) /*!< 0x00000001 */ -#define USB_OTG_DIEPMSK_XFRCM USB_OTG_DIEPMSK_XFRCM_Msk /*!< Transfer completed interrupt mask */ -#define USB_OTG_DIEPMSK_EPDM_Pos (1U) -#define USB_OTG_DIEPMSK_EPDM_Msk (0x1UL << USB_OTG_DIEPMSK_EPDM_Pos) /*!< 0x00000002 */ -#define USB_OTG_DIEPMSK_EPDM USB_OTG_DIEPMSK_EPDM_Msk /*!< Endpoint disabled interrupt mask */ -#define USB_OTG_DIEPMSK_TOM_Pos (3U) -#define USB_OTG_DIEPMSK_TOM_Msk (0x1UL << USB_OTG_DIEPMSK_TOM_Pos) /*!< 0x00000008 */ -#define USB_OTG_DIEPMSK_TOM USB_OTG_DIEPMSK_TOM_Msk /*!< Timeout condition mask (nonisochronous endpoints) */ -#define USB_OTG_DIEPMSK_ITTXFEMSK_Pos (4U) -#define USB_OTG_DIEPMSK_ITTXFEMSK_Msk (0x1UL << USB_OTG_DIEPMSK_ITTXFEMSK_Pos) /*!< 0x00000010 */ -#define USB_OTG_DIEPMSK_ITTXFEMSK USB_OTG_DIEPMSK_ITTXFEMSK_Msk /*!< IN token received when TxFIFO empty mask */ -#define USB_OTG_DIEPMSK_INEPNMM_Pos (5U) -#define USB_OTG_DIEPMSK_INEPNMM_Msk (0x1UL << USB_OTG_DIEPMSK_INEPNMM_Pos) /*!< 0x00000020 */ -#define USB_OTG_DIEPMSK_INEPNMM USB_OTG_DIEPMSK_INEPNMM_Msk /*!< IN token received with EP mismatch mask */ -#define USB_OTG_DIEPMSK_INEPNEM_Pos (6U) -#define USB_OTG_DIEPMSK_INEPNEM_Msk (0x1UL << USB_OTG_DIEPMSK_INEPNEM_Pos) /*!< 0x00000040 */ -#define USB_OTG_DIEPMSK_INEPNEM USB_OTG_DIEPMSK_INEPNEM_Msk /*!< IN endpoint NAK effective mask */ -#define USB_OTG_DIEPMSK_TXFURM_Pos (8U) -#define USB_OTG_DIEPMSK_TXFURM_Msk (0x1UL << USB_OTG_DIEPMSK_TXFURM_Pos) /*!< 0x00000100 */ -#define USB_OTG_DIEPMSK_TXFURM USB_OTG_DIEPMSK_TXFURM_Msk /*!< FIFO underrun mask */ -#define USB_OTG_DIEPMSK_BIM_Pos (9U) -#define USB_OTG_DIEPMSK_BIM_Msk (0x1UL << USB_OTG_DIEPMSK_BIM_Pos) /*!< 0x00000200 */ -#define USB_OTG_DIEPMSK_BIM USB_OTG_DIEPMSK_BIM_Msk /*!< BNA interrupt mask */ - -/******************** Bit definition for USB_OTG_HPTXSTS register ********************/ -#define USB_OTG_HPTXSTS_PTXFSAVL_Pos (0U) -#define USB_OTG_HPTXSTS_PTXFSAVL_Msk (0xFFFFUL << USB_OTG_HPTXSTS_PTXFSAVL_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_HPTXSTS_PTXFSAVL USB_OTG_HPTXSTS_PTXFSAVL_Msk /*!< Periodic transmit data FIFO space available */ -#define USB_OTG_HPTXSTS_PTXQSAV_Pos (16U) -#define USB_OTG_HPTXSTS_PTXQSAV_Msk (0xFFUL << USB_OTG_HPTXSTS_PTXQSAV_Pos) /*!< 0x00FF0000 */ -#define USB_OTG_HPTXSTS_PTXQSAV USB_OTG_HPTXSTS_PTXQSAV_Msk /*!< Periodic transmit request queue space available */ -#define USB_OTG_HPTXSTS_PTXQSAV_0 (0x01UL << USB_OTG_HPTXSTS_PTXQSAV_Pos) /*!< 0x00010000 */ -#define USB_OTG_HPTXSTS_PTXQSAV_1 (0x02UL << USB_OTG_HPTXSTS_PTXQSAV_Pos) /*!< 0x00020000 */ -#define USB_OTG_HPTXSTS_PTXQSAV_2 (0x04UL << USB_OTG_HPTXSTS_PTXQSAV_Pos) /*!< 0x00040000 */ -#define USB_OTG_HPTXSTS_PTXQSAV_3 (0x08UL << USB_OTG_HPTXSTS_PTXQSAV_Pos) /*!< 0x00080000 */ -#define USB_OTG_HPTXSTS_PTXQSAV_4 (0x10UL << USB_OTG_HPTXSTS_PTXQSAV_Pos) /*!< 0x00100000 */ -#define USB_OTG_HPTXSTS_PTXQSAV_5 (0x20UL << USB_OTG_HPTXSTS_PTXQSAV_Pos) /*!< 0x00200000 */ -#define USB_OTG_HPTXSTS_PTXQSAV_6 (0x40UL << USB_OTG_HPTXSTS_PTXQSAV_Pos) /*!< 0x00400000 */ -#define USB_OTG_HPTXSTS_PTXQSAV_7 (0x80UL << USB_OTG_HPTXSTS_PTXQSAV_Pos) /*!< 0x00800000 */ - -#define USB_OTG_HPTXSTS_PTXQTOP_Pos (24U) -#define USB_OTG_HPTXSTS_PTXQTOP_Msk (0xFFUL << USB_OTG_HPTXSTS_PTXQTOP_Pos) /*!< 0xFF000000 */ -#define USB_OTG_HPTXSTS_PTXQTOP USB_OTG_HPTXSTS_PTXQTOP_Msk /*!< Top of the periodic transmit request queue */ -#define USB_OTG_HPTXSTS_PTXQTOP_0 (0x01UL << USB_OTG_HPTXSTS_PTXQTOP_Pos) /*!< 0x01000000 */ -#define USB_OTG_HPTXSTS_PTXQTOP_1 (0x02UL << USB_OTG_HPTXSTS_PTXQTOP_Pos) /*!< 0x02000000 */ -#define USB_OTG_HPTXSTS_PTXQTOP_2 (0x04UL << USB_OTG_HPTXSTS_PTXQTOP_Pos) /*!< 0x04000000 */ -#define USB_OTG_HPTXSTS_PTXQTOP_3 (0x08UL << USB_OTG_HPTXSTS_PTXQTOP_Pos) /*!< 0x08000000 */ -#define USB_OTG_HPTXSTS_PTXQTOP_4 (0x10UL << USB_OTG_HPTXSTS_PTXQTOP_Pos) /*!< 0x10000000 */ -#define USB_OTG_HPTXSTS_PTXQTOP_5 (0x20UL << USB_OTG_HPTXSTS_PTXQTOP_Pos) /*!< 0x20000000 */ -#define USB_OTG_HPTXSTS_PTXQTOP_6 (0x40UL << USB_OTG_HPTXSTS_PTXQTOP_Pos) /*!< 0x40000000 */ -#define USB_OTG_HPTXSTS_PTXQTOP_7 (0x80UL << USB_OTG_HPTXSTS_PTXQTOP_Pos) /*!< 0x80000000 */ - -/******************** Bit definition for USB_OTG_HAINT register ********************/ -#define USB_OTG_HAINT_HAINT_Pos (0U) -#define USB_OTG_HAINT_HAINT_Msk (0xFFFFUL << USB_OTG_HAINT_HAINT_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_HAINT_HAINT USB_OTG_HAINT_HAINT_Msk /*!< Channel interrupts */ - -/******************** Bit definition for USB_OTG_DOEPMSK register ********************/ -#define USB_OTG_DOEPMSK_XFRCM_Pos (0U) -#define USB_OTG_DOEPMSK_XFRCM_Msk (0x1UL << USB_OTG_DOEPMSK_XFRCM_Pos) /*!< 0x00000001 */ -#define USB_OTG_DOEPMSK_XFRCM USB_OTG_DOEPMSK_XFRCM_Msk /*!< Transfer completed interrupt mask */ -#define USB_OTG_DOEPMSK_EPDM_Pos (1U) -#define USB_OTG_DOEPMSK_EPDM_Msk (0x1UL << USB_OTG_DOEPMSK_EPDM_Pos) /*!< 0x00000002 */ -#define USB_OTG_DOEPMSK_EPDM USB_OTG_DOEPMSK_EPDM_Msk /*!< Endpoint disabled interrupt mask */ -#define USB_OTG_DOEPMSK_AHBERRM_Pos (2U) -#define USB_OTG_DOEPMSK_AHBERRM_Msk (0x1UL << USB_OTG_DOEPMSK_AHBERRM_Pos) /*!< 0x00000004 */ -#define USB_OTG_DOEPMSK_AHBERRM USB_OTG_DOEPMSK_AHBERRM_Msk /*!< OUT transaction AHB Error interrupt mask */ -#define USB_OTG_DOEPMSK_STUPM_Pos (3U) -#define USB_OTG_DOEPMSK_STUPM_Msk (0x1UL << USB_OTG_DOEPMSK_STUPM_Pos) /*!< 0x00000008 */ -#define USB_OTG_DOEPMSK_STUPM USB_OTG_DOEPMSK_STUPM_Msk /*!< SETUP phase done mask */ -#define USB_OTG_DOEPMSK_OTEPDM_Pos (4U) -#define USB_OTG_DOEPMSK_OTEPDM_Msk (0x1UL << USB_OTG_DOEPMSK_OTEPDM_Pos) /*!< 0x00000010 */ -#define USB_OTG_DOEPMSK_OTEPDM USB_OTG_DOEPMSK_OTEPDM_Msk /*!< OUT token received when endpoint disabled mask */ -#define USB_OTG_DOEPMSK_OTEPSPRM_Pos (5U) -#define USB_OTG_DOEPMSK_OTEPSPRM_Msk (0x1UL << USB_OTG_DOEPMSK_OTEPSPRM_Pos) /*!< 0x00000020 */ -#define USB_OTG_DOEPMSK_OTEPSPRM USB_OTG_DOEPMSK_OTEPSPRM_Msk /*!< Status Phase Received mask */ -#define USB_OTG_DOEPMSK_B2BSTUP_Pos (6U) -#define USB_OTG_DOEPMSK_B2BSTUP_Msk (0x1UL << USB_OTG_DOEPMSK_B2BSTUP_Pos) /*!< 0x00000040 */ -#define USB_OTG_DOEPMSK_B2BSTUP USB_OTG_DOEPMSK_B2BSTUP_Msk /*!< Back-to-back SETUP packets received mask */ -#define USB_OTG_DOEPMSK_OPEM_Pos (8U) -#define USB_OTG_DOEPMSK_OPEM_Msk (0x1UL << USB_OTG_DOEPMSK_OPEM_Pos) /*!< 0x00000100 */ -#define USB_OTG_DOEPMSK_OPEM USB_OTG_DOEPMSK_OPEM_Msk /*!< OUT packet error mask */ -#define USB_OTG_DOEPMSK_BOIM_Pos (9U) -#define USB_OTG_DOEPMSK_BOIM_Msk (0x1UL << USB_OTG_DOEPMSK_BOIM_Pos) /*!< 0x00000200 */ -#define USB_OTG_DOEPMSK_BOIM USB_OTG_DOEPMSK_BOIM_Msk /*!< BNA interrupt mask */ -#define USB_OTG_DOEPMSK_BERRM_Pos (12U) -#define USB_OTG_DOEPMSK_BERRM_Msk (0x1UL << USB_OTG_DOEPMSK_BERRM_Pos) /*!< 0x00001000 */ -#define USB_OTG_DOEPMSK_BERRM USB_OTG_DOEPMSK_BERRM_Msk /*!< Babble error interrupt mask */ -#define USB_OTG_DOEPMSK_NAKM_Pos (13U) -#define USB_OTG_DOEPMSK_NAKM_Msk (0x1UL << USB_OTG_DOEPMSK_NAKM_Pos) /*!< 0x00002000 */ -#define USB_OTG_DOEPMSK_NAKM USB_OTG_DOEPMSK_NAKM_Msk /*!< OUT Packet NAK interrupt mask */ -#define USB_OTG_DOEPMSK_NYETM_Pos (14U) -#define USB_OTG_DOEPMSK_NYETM_Msk (0x1UL << USB_OTG_DOEPMSK_NYETM_Pos) /*!< 0x00004000 */ -#define USB_OTG_DOEPMSK_NYETM USB_OTG_DOEPMSK_NYETM_Msk /*!< NYET interrupt mask */ -/******************** Bit definition for USB_OTG_GINTSTS register ********************/ -#define USB_OTG_GINTSTS_CMOD_Pos (0U) -#define USB_OTG_GINTSTS_CMOD_Msk (0x1UL << USB_OTG_GINTSTS_CMOD_Pos) /*!< 0x00000001 */ -#define USB_OTG_GINTSTS_CMOD USB_OTG_GINTSTS_CMOD_Msk /*!< Current mode of operation */ -#define USB_OTG_GINTSTS_MMIS_Pos (1U) -#define USB_OTG_GINTSTS_MMIS_Msk (0x1UL << USB_OTG_GINTSTS_MMIS_Pos) /*!< 0x00000002 */ -#define USB_OTG_GINTSTS_MMIS USB_OTG_GINTSTS_MMIS_Msk /*!< Mode mismatch interrupt */ -#define USB_OTG_GINTSTS_OTGINT_Pos (2U) -#define USB_OTG_GINTSTS_OTGINT_Msk (0x1UL << USB_OTG_GINTSTS_OTGINT_Pos) /*!< 0x00000004 */ -#define USB_OTG_GINTSTS_OTGINT USB_OTG_GINTSTS_OTGINT_Msk /*!< OTG interrupt */ -#define USB_OTG_GINTSTS_SOF_Pos (3U) -#define USB_OTG_GINTSTS_SOF_Msk (0x1UL << USB_OTG_GINTSTS_SOF_Pos) /*!< 0x00000008 */ -#define USB_OTG_GINTSTS_SOF USB_OTG_GINTSTS_SOF_Msk /*!< Start of frame */ -#define USB_OTG_GINTSTS_RXFLVL_Pos (4U) -#define USB_OTG_GINTSTS_RXFLVL_Msk (0x1UL << USB_OTG_GINTSTS_RXFLVL_Pos) /*!< 0x00000010 */ -#define USB_OTG_GINTSTS_RXFLVL USB_OTG_GINTSTS_RXFLVL_Msk /*!< RxFIFO nonempty */ -#define USB_OTG_GINTSTS_NPTXFE_Pos (5U) -#define USB_OTG_GINTSTS_NPTXFE_Msk (0x1UL << USB_OTG_GINTSTS_NPTXFE_Pos) /*!< 0x00000020 */ -#define USB_OTG_GINTSTS_NPTXFE USB_OTG_GINTSTS_NPTXFE_Msk /*!< Nonperiodic TxFIFO empty */ -#define USB_OTG_GINTSTS_GINAKEFF_Pos (6U) -#define USB_OTG_GINTSTS_GINAKEFF_Msk (0x1UL << USB_OTG_GINTSTS_GINAKEFF_Pos) /*!< 0x00000040 */ -#define USB_OTG_GINTSTS_GINAKEFF USB_OTG_GINTSTS_GINAKEFF_Msk /*!< Global IN nonperiodic NAK effective */ -#define USB_OTG_GINTSTS_BOUTNAKEFF_Pos (7U) -#define USB_OTG_GINTSTS_BOUTNAKEFF_Msk (0x1UL << USB_OTG_GINTSTS_BOUTNAKEFF_Pos) /*!< 0x00000080 */ -#define USB_OTG_GINTSTS_BOUTNAKEFF USB_OTG_GINTSTS_BOUTNAKEFF_Msk /*!< Global OUT NAK effective */ -#define USB_OTG_GINTSTS_ESUSP_Pos (10U) -#define USB_OTG_GINTSTS_ESUSP_Msk (0x1UL << USB_OTG_GINTSTS_ESUSP_Pos) /*!< 0x00000400 */ -#define USB_OTG_GINTSTS_ESUSP USB_OTG_GINTSTS_ESUSP_Msk /*!< Early suspend */ -#define USB_OTG_GINTSTS_USBSUSP_Pos (11U) -#define USB_OTG_GINTSTS_USBSUSP_Msk (0x1UL << USB_OTG_GINTSTS_USBSUSP_Pos) /*!< 0x00000800 */ -#define USB_OTG_GINTSTS_USBSUSP USB_OTG_GINTSTS_USBSUSP_Msk /*!< USB suspend */ -#define USB_OTG_GINTSTS_USBRST_Pos (12U) -#define USB_OTG_GINTSTS_USBRST_Msk (0x1UL << USB_OTG_GINTSTS_USBRST_Pos) /*!< 0x00001000 */ -#define USB_OTG_GINTSTS_USBRST USB_OTG_GINTSTS_USBRST_Msk /*!< USB reset */ -#define USB_OTG_GINTSTS_ENUMDNE_Pos (13U) -#define USB_OTG_GINTSTS_ENUMDNE_Msk (0x1UL << USB_OTG_GINTSTS_ENUMDNE_Pos) /*!< 0x00002000 */ -#define USB_OTG_GINTSTS_ENUMDNE USB_OTG_GINTSTS_ENUMDNE_Msk /*!< Enumeration done */ -#define USB_OTG_GINTSTS_ISOODRP_Pos (14U) -#define USB_OTG_GINTSTS_ISOODRP_Msk (0x1UL << USB_OTG_GINTSTS_ISOODRP_Pos) /*!< 0x00004000 */ -#define USB_OTG_GINTSTS_ISOODRP USB_OTG_GINTSTS_ISOODRP_Msk /*!< Isochronous OUT packet dropped interrupt */ -#define USB_OTG_GINTSTS_EOPF_Pos (15U) -#define USB_OTG_GINTSTS_EOPF_Msk (0x1UL << USB_OTG_GINTSTS_EOPF_Pos) /*!< 0x00008000 */ -#define USB_OTG_GINTSTS_EOPF USB_OTG_GINTSTS_EOPF_Msk /*!< End of periodic frame interrupt */ -#define USB_OTG_GINTSTS_IEPINT_Pos (18U) -#define USB_OTG_GINTSTS_IEPINT_Msk (0x1UL << USB_OTG_GINTSTS_IEPINT_Pos) /*!< 0x00040000 */ -#define USB_OTG_GINTSTS_IEPINT USB_OTG_GINTSTS_IEPINT_Msk /*!< IN endpoint interrupt */ -#define USB_OTG_GINTSTS_OEPINT_Pos (19U) -#define USB_OTG_GINTSTS_OEPINT_Msk (0x1UL << USB_OTG_GINTSTS_OEPINT_Pos) /*!< 0x00080000 */ -#define USB_OTG_GINTSTS_OEPINT USB_OTG_GINTSTS_OEPINT_Msk /*!< OUT endpoint interrupt */ -#define USB_OTG_GINTSTS_IISOIXFR_Pos (20U) -#define USB_OTG_GINTSTS_IISOIXFR_Msk (0x1UL << USB_OTG_GINTSTS_IISOIXFR_Pos) /*!< 0x00100000 */ -#define USB_OTG_GINTSTS_IISOIXFR USB_OTG_GINTSTS_IISOIXFR_Msk /*!< Incomplete isochronous IN transfer */ -#define USB_OTG_GINTSTS_PXFR_INCOMPISOOUT_Pos (21U) -#define USB_OTG_GINTSTS_PXFR_INCOMPISOOUT_Msk (0x1UL << USB_OTG_GINTSTS_PXFR_INCOMPISOOUT_Pos) /*!< 0x00200000 */ -#define USB_OTG_GINTSTS_PXFR_INCOMPISOOUT USB_OTG_GINTSTS_PXFR_INCOMPISOOUT_Msk /*!< Incomplete periodic transfer */ -#define USB_OTG_GINTSTS_DATAFSUSP_Pos (22U) -#define USB_OTG_GINTSTS_DATAFSUSP_Msk (0x1UL << USB_OTG_GINTSTS_DATAFSUSP_Pos) /*!< 0x00400000 */ -#define USB_OTG_GINTSTS_DATAFSUSP USB_OTG_GINTSTS_DATAFSUSP_Msk /*!< Data fetch suspended */ -#define USB_OTG_GINTSTS_HPRTINT_Pos (24U) -#define USB_OTG_GINTSTS_HPRTINT_Msk (0x1UL << USB_OTG_GINTSTS_HPRTINT_Pos) /*!< 0x01000000 */ -#define USB_OTG_GINTSTS_HPRTINT USB_OTG_GINTSTS_HPRTINT_Msk /*!< Host port interrupt */ -#define USB_OTG_GINTSTS_HCINT_Pos (25U) -#define USB_OTG_GINTSTS_HCINT_Msk (0x1UL << USB_OTG_GINTSTS_HCINT_Pos) /*!< 0x02000000 */ -#define USB_OTG_GINTSTS_HCINT USB_OTG_GINTSTS_HCINT_Msk /*!< Host channels interrupt */ -#define USB_OTG_GINTSTS_PTXFE_Pos (26U) -#define USB_OTG_GINTSTS_PTXFE_Msk (0x1UL << USB_OTG_GINTSTS_PTXFE_Pos) /*!< 0x04000000 */ -#define USB_OTG_GINTSTS_PTXFE USB_OTG_GINTSTS_PTXFE_Msk /*!< Periodic TxFIFO empty */ -#define USB_OTG_GINTSTS_CIDSCHG_Pos (28U) -#define USB_OTG_GINTSTS_CIDSCHG_Msk (0x1UL << USB_OTG_GINTSTS_CIDSCHG_Pos) /*!< 0x10000000 */ -#define USB_OTG_GINTSTS_CIDSCHG USB_OTG_GINTSTS_CIDSCHG_Msk /*!< Connector ID status change */ -#define USB_OTG_GINTSTS_DISCINT_Pos (29U) -#define USB_OTG_GINTSTS_DISCINT_Msk (0x1UL << USB_OTG_GINTSTS_DISCINT_Pos) /*!< 0x20000000 */ -#define USB_OTG_GINTSTS_DISCINT USB_OTG_GINTSTS_DISCINT_Msk /*!< Disconnect detected interrupt */ -#define USB_OTG_GINTSTS_SRQINT_Pos (30U) -#define USB_OTG_GINTSTS_SRQINT_Msk (0x1UL << USB_OTG_GINTSTS_SRQINT_Pos) /*!< 0x40000000 */ -#define USB_OTG_GINTSTS_SRQINT USB_OTG_GINTSTS_SRQINT_Msk /*!< Session request/new session detected interrupt */ -#define USB_OTG_GINTSTS_WKUINT_Pos (31U) -#define USB_OTG_GINTSTS_WKUINT_Msk (0x1UL << USB_OTG_GINTSTS_WKUINT_Pos) /*!< 0x80000000 */ -#define USB_OTG_GINTSTS_WKUINT USB_OTG_GINTSTS_WKUINT_Msk /*!< Resume/remote wakeup detected interrupt */ - -/******************** Bit definition for USB_OTG_GINTMSK register ********************/ -#define USB_OTG_GINTMSK_MMISM_Pos (1U) -#define USB_OTG_GINTMSK_MMISM_Msk (0x1UL << USB_OTG_GINTMSK_MMISM_Pos) /*!< 0x00000002 */ -#define USB_OTG_GINTMSK_MMISM USB_OTG_GINTMSK_MMISM_Msk /*!< Mode mismatch interrupt mask */ -#define USB_OTG_GINTMSK_OTGINT_Pos (2U) -#define USB_OTG_GINTMSK_OTGINT_Msk (0x1UL << USB_OTG_GINTMSK_OTGINT_Pos) /*!< 0x00000004 */ -#define USB_OTG_GINTMSK_OTGINT USB_OTG_GINTMSK_OTGINT_Msk /*!< OTG interrupt mask */ -#define USB_OTG_GINTMSK_SOFM_Pos (3U) -#define USB_OTG_GINTMSK_SOFM_Msk (0x1UL << USB_OTG_GINTMSK_SOFM_Pos) /*!< 0x00000008 */ -#define USB_OTG_GINTMSK_SOFM USB_OTG_GINTMSK_SOFM_Msk /*!< Start of frame mask */ -#define USB_OTG_GINTMSK_RXFLVLM_Pos (4U) -#define USB_OTG_GINTMSK_RXFLVLM_Msk (0x1UL << USB_OTG_GINTMSK_RXFLVLM_Pos) /*!< 0x00000010 */ -#define USB_OTG_GINTMSK_RXFLVLM USB_OTG_GINTMSK_RXFLVLM_Msk /*!< Receive FIFO nonempty mask */ -#define USB_OTG_GINTMSK_NPTXFEM_Pos (5U) -#define USB_OTG_GINTMSK_NPTXFEM_Msk (0x1UL << USB_OTG_GINTMSK_NPTXFEM_Pos) /*!< 0x00000020 */ -#define USB_OTG_GINTMSK_NPTXFEM USB_OTG_GINTMSK_NPTXFEM_Msk /*!< Nonperiodic TxFIFO empty mask */ -#define USB_OTG_GINTMSK_GINAKEFFM_Pos (6U) -#define USB_OTG_GINTMSK_GINAKEFFM_Msk (0x1UL << USB_OTG_GINTMSK_GINAKEFFM_Pos) /*!< 0x00000040 */ -#define USB_OTG_GINTMSK_GINAKEFFM USB_OTG_GINTMSK_GINAKEFFM_Msk /*!< Global nonperiodic IN NAK effective mask */ -#define USB_OTG_GINTMSK_GONAKEFFM_Pos (7U) -#define USB_OTG_GINTMSK_GONAKEFFM_Msk (0x1UL << USB_OTG_GINTMSK_GONAKEFFM_Pos) /*!< 0x00000080 */ -#define USB_OTG_GINTMSK_GONAKEFFM USB_OTG_GINTMSK_GONAKEFFM_Msk /*!< Global OUT NAK effective mask */ -#define USB_OTG_GINTMSK_ESUSPM_Pos (10U) -#define USB_OTG_GINTMSK_ESUSPM_Msk (0x1UL << USB_OTG_GINTMSK_ESUSPM_Pos) /*!< 0x00000400 */ -#define USB_OTG_GINTMSK_ESUSPM USB_OTG_GINTMSK_ESUSPM_Msk /*!< Early suspend mask */ -#define USB_OTG_GINTMSK_USBSUSPM_Pos (11U) -#define USB_OTG_GINTMSK_USBSUSPM_Msk (0x1UL << USB_OTG_GINTMSK_USBSUSPM_Pos) /*!< 0x00000800 */ -#define USB_OTG_GINTMSK_USBSUSPM USB_OTG_GINTMSK_USBSUSPM_Msk /*!< USB suspend mask */ -#define USB_OTG_GINTMSK_USBRST_Pos (12U) -#define USB_OTG_GINTMSK_USBRST_Msk (0x1UL << USB_OTG_GINTMSK_USBRST_Pos) /*!< 0x00001000 */ -#define USB_OTG_GINTMSK_USBRST USB_OTG_GINTMSK_USBRST_Msk /*!< USB reset mask */ -#define USB_OTG_GINTMSK_ENUMDNEM_Pos (13U) -#define USB_OTG_GINTMSK_ENUMDNEM_Msk (0x1UL << USB_OTG_GINTMSK_ENUMDNEM_Pos) /*!< 0x00002000 */ -#define USB_OTG_GINTMSK_ENUMDNEM USB_OTG_GINTMSK_ENUMDNEM_Msk /*!< Enumeration done mask */ -#define USB_OTG_GINTMSK_ISOODRPM_Pos (14U) -#define USB_OTG_GINTMSK_ISOODRPM_Msk (0x1UL << USB_OTG_GINTMSK_ISOODRPM_Pos) /*!< 0x00004000 */ -#define USB_OTG_GINTMSK_ISOODRPM USB_OTG_GINTMSK_ISOODRPM_Msk /*!< Isochronous OUT packet dropped interrupt mask */ -#define USB_OTG_GINTMSK_EOPFM_Pos (15U) -#define USB_OTG_GINTMSK_EOPFM_Msk (0x1UL << USB_OTG_GINTMSK_EOPFM_Pos) /*!< 0x00008000 */ -#define USB_OTG_GINTMSK_EOPFM USB_OTG_GINTMSK_EOPFM_Msk /*!< End of periodic frame interrupt mask */ -#define USB_OTG_GINTMSK_EPMISM_Pos (17U) -#define USB_OTG_GINTMSK_EPMISM_Msk (0x1UL << USB_OTG_GINTMSK_EPMISM_Pos) /*!< 0x00020000 */ -#define USB_OTG_GINTMSK_EPMISM USB_OTG_GINTMSK_EPMISM_Msk /*!< Endpoint mismatch interrupt mask */ -#define USB_OTG_GINTMSK_IEPINT_Pos (18U) -#define USB_OTG_GINTMSK_IEPINT_Msk (0x1UL << USB_OTG_GINTMSK_IEPINT_Pos) /*!< 0x00040000 */ -#define USB_OTG_GINTMSK_IEPINT USB_OTG_GINTMSK_IEPINT_Msk /*!< IN endpoints interrupt mask */ -#define USB_OTG_GINTMSK_OEPINT_Pos (19U) -#define USB_OTG_GINTMSK_OEPINT_Msk (0x1UL << USB_OTG_GINTMSK_OEPINT_Pos) /*!< 0x00080000 */ -#define USB_OTG_GINTMSK_OEPINT USB_OTG_GINTMSK_OEPINT_Msk /*!< OUT endpoints interrupt mask */ -#define USB_OTG_GINTMSK_IISOIXFRM_Pos (20U) -#define USB_OTG_GINTMSK_IISOIXFRM_Msk (0x1UL << USB_OTG_GINTMSK_IISOIXFRM_Pos) /*!< 0x00100000 */ -#define USB_OTG_GINTMSK_IISOIXFRM USB_OTG_GINTMSK_IISOIXFRM_Msk /*!< Incomplete isochronous IN transfer mask */ -#define USB_OTG_GINTMSK_PXFRM_IISOOXFRM_Pos (21U) -#define USB_OTG_GINTMSK_PXFRM_IISOOXFRM_Msk (0x1UL << USB_OTG_GINTMSK_PXFRM_IISOOXFRM_Pos) /*!< 0x00200000 */ -#define USB_OTG_GINTMSK_PXFRM_IISOOXFRM USB_OTG_GINTMSK_PXFRM_IISOOXFRM_Msk /*!< Incomplete periodic transfer mask */ -#define USB_OTG_GINTMSK_FSUSPM_Pos (22U) -#define USB_OTG_GINTMSK_FSUSPM_Msk (0x1UL << USB_OTG_GINTMSK_FSUSPM_Pos) /*!< 0x00400000 */ -#define USB_OTG_GINTMSK_FSUSPM USB_OTG_GINTMSK_FSUSPM_Msk /*!< Data fetch suspended mask */ -#define USB_OTG_GINTMSK_PRTIM_Pos (24U) -#define USB_OTG_GINTMSK_PRTIM_Msk (0x1UL << USB_OTG_GINTMSK_PRTIM_Pos) /*!< 0x01000000 */ -#define USB_OTG_GINTMSK_PRTIM USB_OTG_GINTMSK_PRTIM_Msk /*!< Host port interrupt mask */ -#define USB_OTG_GINTMSK_HCIM_Pos (25U) -#define USB_OTG_GINTMSK_HCIM_Msk (0x1UL << USB_OTG_GINTMSK_HCIM_Pos) /*!< 0x02000000 */ -#define USB_OTG_GINTMSK_HCIM USB_OTG_GINTMSK_HCIM_Msk /*!< Host channels interrupt mask */ -#define USB_OTG_GINTMSK_PTXFEM_Pos (26U) -#define USB_OTG_GINTMSK_PTXFEM_Msk (0x1UL << USB_OTG_GINTMSK_PTXFEM_Pos) /*!< 0x04000000 */ -#define USB_OTG_GINTMSK_PTXFEM USB_OTG_GINTMSK_PTXFEM_Msk /*!< Periodic TxFIFO empty mask */ -#define USB_OTG_GINTMSK_CIDSCHGM_Pos (28U) -#define USB_OTG_GINTMSK_CIDSCHGM_Msk (0x1UL << USB_OTG_GINTMSK_CIDSCHGM_Pos) /*!< 0x10000000 */ -#define USB_OTG_GINTMSK_CIDSCHGM USB_OTG_GINTMSK_CIDSCHGM_Msk /*!< Connector ID status change mask */ -#define USB_OTG_GINTMSK_DISCINT_Pos (29U) -#define USB_OTG_GINTMSK_DISCINT_Msk (0x1UL << USB_OTG_GINTMSK_DISCINT_Pos) /*!< 0x20000000 */ -#define USB_OTG_GINTMSK_DISCINT USB_OTG_GINTMSK_DISCINT_Msk /*!< Disconnect detected interrupt mask */ -#define USB_OTG_GINTMSK_SRQIM_Pos (30U) -#define USB_OTG_GINTMSK_SRQIM_Msk (0x1UL << USB_OTG_GINTMSK_SRQIM_Pos) /*!< 0x40000000 */ -#define USB_OTG_GINTMSK_SRQIM USB_OTG_GINTMSK_SRQIM_Msk /*!< Session request/new session detected interrupt mask */ -#define USB_OTG_GINTMSK_WUIM_Pos (31U) -#define USB_OTG_GINTMSK_WUIM_Msk (0x1UL << USB_OTG_GINTMSK_WUIM_Pos) /*!< 0x80000000 */ -#define USB_OTG_GINTMSK_WUIM USB_OTG_GINTMSK_WUIM_Msk /*!< Resume/remote wakeup detected interrupt mask */ - -/******************** Bit definition for USB_OTG_DAINT register ********************/ -#define USB_OTG_DAINT_IEPINT_Pos (0U) -#define USB_OTG_DAINT_IEPINT_Msk (0xFFFFUL << USB_OTG_DAINT_IEPINT_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_DAINT_IEPINT USB_OTG_DAINT_IEPINT_Msk /*!< IN endpoint interrupt bits */ -#define USB_OTG_DAINT_OEPINT_Pos (16U) -#define USB_OTG_DAINT_OEPINT_Msk (0xFFFFUL << USB_OTG_DAINT_OEPINT_Pos) /*!< 0xFFFF0000 */ -#define USB_OTG_DAINT_OEPINT USB_OTG_DAINT_OEPINT_Msk /*!< OUT endpoint interrupt bits */ - -/******************** Bit definition for USB_OTG_HAINTMSK register ********************/ -#define USB_OTG_HAINTMSK_HAINTM_Pos (0U) -#define USB_OTG_HAINTMSK_HAINTM_Msk (0xFFFFUL << USB_OTG_HAINTMSK_HAINTM_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_HAINTMSK_HAINTM USB_OTG_HAINTMSK_HAINTM_Msk /*!< Channel interrupt mask */ - -/******************** Bit definition for USB_OTG_GRXSTSP register ********************/ -#define USB_OTG_GRXSTSP_EPNUM_Pos (0U) -#define USB_OTG_GRXSTSP_EPNUM_Msk (0xFUL << USB_OTG_GRXSTSP_EPNUM_Pos) /*!< 0x0000000F */ -#define USB_OTG_GRXSTSP_EPNUM USB_OTG_GRXSTSP_EPNUM_Msk /*!< IN EP interrupt mask bits */ -#define USB_OTG_GRXSTSP_BCNT_Pos (4U) -#define USB_OTG_GRXSTSP_BCNT_Msk (0x7FFUL << USB_OTG_GRXSTSP_BCNT_Pos) /*!< 0x00007FF0 */ -#define USB_OTG_GRXSTSP_BCNT USB_OTG_GRXSTSP_BCNT_Msk /*!< OUT EP interrupt mask bits */ -#define USB_OTG_GRXSTSP_DPID_Pos (15U) -#define USB_OTG_GRXSTSP_DPID_Msk (0x3UL << USB_OTG_GRXSTSP_DPID_Pos) /*!< 0x00018000 */ -#define USB_OTG_GRXSTSP_DPID USB_OTG_GRXSTSP_DPID_Msk /*!< OUT EP interrupt mask bits */ -#define USB_OTG_GRXSTSP_PKTSTS_Pos (17U) -#define USB_OTG_GRXSTSP_PKTSTS_Msk (0xFUL << USB_OTG_GRXSTSP_PKTSTS_Pos) /*!< 0x001E0000 */ -#define USB_OTG_GRXSTSP_PKTSTS USB_OTG_GRXSTSP_PKTSTS_Msk /*!< OUT EP interrupt mask bits */ - -/******************** Bit definition for USB_OTG_DAINTMSK register ********************/ -#define USB_OTG_DAINTMSK_IEPM_Pos (0U) -#define USB_OTG_DAINTMSK_IEPM_Msk (0xFFFFUL << USB_OTG_DAINTMSK_IEPM_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_DAINTMSK_IEPM USB_OTG_DAINTMSK_IEPM_Msk /*!< IN EP interrupt mask bits */ -#define USB_OTG_DAINTMSK_OEPM_Pos (16U) -#define USB_OTG_DAINTMSK_OEPM_Msk (0xFFFFUL << USB_OTG_DAINTMSK_OEPM_Pos) /*!< 0xFFFF0000 */ -#define USB_OTG_DAINTMSK_OEPM USB_OTG_DAINTMSK_OEPM_Msk /*!< OUT EP interrupt mask bits */ - -/******************** Bit definition for USB_OTG_GRXFSIZ register ********************/ -#define USB_OTG_GRXFSIZ_RXFD_Pos (0U) -#define USB_OTG_GRXFSIZ_RXFD_Msk (0xFFFFUL << USB_OTG_GRXFSIZ_RXFD_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_GRXFSIZ_RXFD USB_OTG_GRXFSIZ_RXFD_Msk /*!< RxFIFO depth */ - -/******************** Bit definition for USB_OTG_DVBUSDIS register ********************/ -#define USB_OTG_DVBUSDIS_VBUSDT_Pos (0U) -#define USB_OTG_DVBUSDIS_VBUSDT_Msk (0xFFFFUL << USB_OTG_DVBUSDIS_VBUSDT_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_DVBUSDIS_VBUSDT USB_OTG_DVBUSDIS_VBUSDT_Msk /*!< Device VBUS discharge time */ - -/******************** Bit definition for OTG register ********************/ -#define USB_OTG_NPTXFSA_Pos (0U) -#define USB_OTG_NPTXFSA_Msk (0xFFFFUL << USB_OTG_NPTXFSA_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_NPTXFSA USB_OTG_NPTXFSA_Msk /*!< Nonperiodic transmit RAM start address */ -#define USB_OTG_NPTXFD_Pos (16U) -#define USB_OTG_NPTXFD_Msk (0xFFFFUL << USB_OTG_NPTXFD_Pos) /*!< 0xFFFF0000 */ -#define USB_OTG_NPTXFD USB_OTG_NPTXFD_Msk /*!< Nonperiodic TxFIFO depth */ -#define USB_OTG_TX0FSA_Pos (0U) -#define USB_OTG_TX0FSA_Msk (0xFFFFUL << USB_OTG_TX0FSA_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_TX0FSA USB_OTG_TX0FSA_Msk /*!< Endpoint 0 transmit RAM start address */ -#define USB_OTG_TX0FD_Pos (16U) -#define USB_OTG_TX0FD_Msk (0xFFFFUL << USB_OTG_TX0FD_Pos) /*!< 0xFFFF0000 */ -#define USB_OTG_TX0FD USB_OTG_TX0FD_Msk /*!< Endpoint 0 TxFIFO depth */ - -/******************** Bit definition for USB_OTG_DVBUSPULSE register ********************/ -#define USB_OTG_DVBUSPULSE_DVBUSP_Pos (0U) -#define USB_OTG_DVBUSPULSE_DVBUSP_Msk (0xFFFUL << USB_OTG_DVBUSPULSE_DVBUSP_Pos) /*!< 0x00000FFF */ -#define USB_OTG_DVBUSPULSE_DVBUSP USB_OTG_DVBUSPULSE_DVBUSP_Msk /*!< Device VBUS pulsing time */ - -/******************** Bit definition for USB_OTG_GNPTXSTS register ********************/ -#define USB_OTG_GNPTXSTS_NPTXFSAV_Pos (0U) -#define USB_OTG_GNPTXSTS_NPTXFSAV_Msk (0xFFFFUL << USB_OTG_GNPTXSTS_NPTXFSAV_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_GNPTXSTS_NPTXFSAV USB_OTG_GNPTXSTS_NPTXFSAV_Msk /*!< Nonperiodic TxFIFO space available */ - -#define USB_OTG_GNPTXSTS_NPTQXSAV_Pos (16U) -#define USB_OTG_GNPTXSTS_NPTQXSAV_Msk (0xFFUL << USB_OTG_GNPTXSTS_NPTQXSAV_Pos) /*!< 0x00FF0000 */ -#define USB_OTG_GNPTXSTS_NPTQXSAV USB_OTG_GNPTXSTS_NPTQXSAV_Msk /*!< Nonperiodic transmit request queue space available */ -#define USB_OTG_GNPTXSTS_NPTQXSAV_0 (0x01UL << USB_OTG_GNPTXSTS_NPTQXSAV_Pos) /*!< 0x00010000 */ -#define USB_OTG_GNPTXSTS_NPTQXSAV_1 (0x02UL << USB_OTG_GNPTXSTS_NPTQXSAV_Pos) /*!< 0x00020000 */ -#define USB_OTG_GNPTXSTS_NPTQXSAV_2 (0x04UL << USB_OTG_GNPTXSTS_NPTQXSAV_Pos) /*!< 0x00040000 */ -#define USB_OTG_GNPTXSTS_NPTQXSAV_3 (0x08UL << USB_OTG_GNPTXSTS_NPTQXSAV_Pos) /*!< 0x00080000 */ -#define USB_OTG_GNPTXSTS_NPTQXSAV_4 (0x10UL << USB_OTG_GNPTXSTS_NPTQXSAV_Pos) /*!< 0x00100000 */ -#define USB_OTG_GNPTXSTS_NPTQXSAV_5 (0x20UL << USB_OTG_GNPTXSTS_NPTQXSAV_Pos) /*!< 0x00200000 */ -#define USB_OTG_GNPTXSTS_NPTQXSAV_6 (0x40UL << USB_OTG_GNPTXSTS_NPTQXSAV_Pos) /*!< 0x00400000 */ -#define USB_OTG_GNPTXSTS_NPTQXSAV_7 (0x80UL << USB_OTG_GNPTXSTS_NPTQXSAV_Pos) /*!< 0x00800000 */ - -#define USB_OTG_GNPTXSTS_NPTXQTOP_Pos (24U) -#define USB_OTG_GNPTXSTS_NPTXQTOP_Msk (0x7FUL << USB_OTG_GNPTXSTS_NPTXQTOP_Pos) /*!< 0x7F000000 */ -#define USB_OTG_GNPTXSTS_NPTXQTOP USB_OTG_GNPTXSTS_NPTXQTOP_Msk /*!< Top of the nonperiodic transmit request queue */ -#define USB_OTG_GNPTXSTS_NPTXQTOP_0 (0x01UL << USB_OTG_GNPTXSTS_NPTXQTOP_Pos) /*!< 0x01000000 */ -#define USB_OTG_GNPTXSTS_NPTXQTOP_1 (0x02UL << USB_OTG_GNPTXSTS_NPTXQTOP_Pos) /*!< 0x02000000 */ -#define USB_OTG_GNPTXSTS_NPTXQTOP_2 (0x04UL << USB_OTG_GNPTXSTS_NPTXQTOP_Pos) /*!< 0x04000000 */ -#define USB_OTG_GNPTXSTS_NPTXQTOP_3 (0x08UL << USB_OTG_GNPTXSTS_NPTXQTOP_Pos) /*!< 0x08000000 */ -#define USB_OTG_GNPTXSTS_NPTXQTOP_4 (0x10UL << USB_OTG_GNPTXSTS_NPTXQTOP_Pos) /*!< 0x10000000 */ -#define USB_OTG_GNPTXSTS_NPTXQTOP_5 (0x20UL << USB_OTG_GNPTXSTS_NPTXQTOP_Pos) /*!< 0x20000000 */ -#define USB_OTG_GNPTXSTS_NPTXQTOP_6 (0x40UL << USB_OTG_GNPTXSTS_NPTXQTOP_Pos) /*!< 0x40000000 */ - -/******************** Bit definition for USB_OTG_DTHRCTL register ********************/ -#define USB_OTG_DTHRCTL_NONISOTHREN_Pos (0U) -#define USB_OTG_DTHRCTL_NONISOTHREN_Msk (0x1UL << USB_OTG_DTHRCTL_NONISOTHREN_Pos) /*!< 0x00000001 */ -#define USB_OTG_DTHRCTL_NONISOTHREN USB_OTG_DTHRCTL_NONISOTHREN_Msk /*!< Nonisochronous IN endpoints threshold enable */ -#define USB_OTG_DTHRCTL_ISOTHREN_Pos (1U) -#define USB_OTG_DTHRCTL_ISOTHREN_Msk (0x1UL << USB_OTG_DTHRCTL_ISOTHREN_Pos) /*!< 0x00000002 */ -#define USB_OTG_DTHRCTL_ISOTHREN USB_OTG_DTHRCTL_ISOTHREN_Msk /*!< ISO IN endpoint threshold enable */ - -#define USB_OTG_DTHRCTL_TXTHRLEN_Pos (2U) -#define USB_OTG_DTHRCTL_TXTHRLEN_Msk (0x1FFUL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x000007FC */ -#define USB_OTG_DTHRCTL_TXTHRLEN USB_OTG_DTHRCTL_TXTHRLEN_Msk /*!< Transmit threshold length */ -#define USB_OTG_DTHRCTL_TXTHRLEN_0 (0x001UL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x00000004 */ -#define USB_OTG_DTHRCTL_TXTHRLEN_1 (0x002UL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x00000008 */ -#define USB_OTG_DTHRCTL_TXTHRLEN_2 (0x004UL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x00000010 */ -#define USB_OTG_DTHRCTL_TXTHRLEN_3 (0x008UL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x00000020 */ -#define USB_OTG_DTHRCTL_TXTHRLEN_4 (0x010UL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x00000040 */ -#define USB_OTG_DTHRCTL_TXTHRLEN_5 (0x020UL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x00000080 */ -#define USB_OTG_DTHRCTL_TXTHRLEN_6 (0x040UL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x00000100 */ -#define USB_OTG_DTHRCTL_TXTHRLEN_7 (0x080UL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x00000200 */ -#define USB_OTG_DTHRCTL_TXTHRLEN_8 (0x100UL << USB_OTG_DTHRCTL_TXTHRLEN_Pos) /*!< 0x00000400 */ -#define USB_OTG_DTHRCTL_RXTHREN_Pos (16U) -#define USB_OTG_DTHRCTL_RXTHREN_Msk (0x1UL << USB_OTG_DTHRCTL_RXTHREN_Pos) /*!< 0x00010000 */ -#define USB_OTG_DTHRCTL_RXTHREN USB_OTG_DTHRCTL_RXTHREN_Msk /*!< Receive threshold enable */ - -#define USB_OTG_DTHRCTL_RXTHRLEN_Pos (17U) -#define USB_OTG_DTHRCTL_RXTHRLEN_Msk (0x1FFUL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x03FE0000 */ -#define USB_OTG_DTHRCTL_RXTHRLEN USB_OTG_DTHRCTL_RXTHRLEN_Msk /*!< Receive threshold length */ -#define USB_OTG_DTHRCTL_RXTHRLEN_0 (0x001UL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x00020000 */ -#define USB_OTG_DTHRCTL_RXTHRLEN_1 (0x002UL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x00040000 */ -#define USB_OTG_DTHRCTL_RXTHRLEN_2 (0x004UL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x00080000 */ -#define USB_OTG_DTHRCTL_RXTHRLEN_3 (0x008UL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x00100000 */ -#define USB_OTG_DTHRCTL_RXTHRLEN_4 (0x010UL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x00200000 */ -#define USB_OTG_DTHRCTL_RXTHRLEN_5 (0x020UL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x00400000 */ -#define USB_OTG_DTHRCTL_RXTHRLEN_6 (0x040UL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x00800000 */ -#define USB_OTG_DTHRCTL_RXTHRLEN_7 (0x080UL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x01000000 */ -#define USB_OTG_DTHRCTL_RXTHRLEN_8 (0x100UL << USB_OTG_DTHRCTL_RXTHRLEN_Pos) /*!< 0x02000000 */ -#define USB_OTG_DTHRCTL_ARPEN_Pos (27U) -#define USB_OTG_DTHRCTL_ARPEN_Msk (0x1UL << USB_OTG_DTHRCTL_ARPEN_Pos) /*!< 0x08000000 */ -#define USB_OTG_DTHRCTL_ARPEN USB_OTG_DTHRCTL_ARPEN_Msk /*!< Arbiter parking enable */ - -/******************** Bit definition for USB_OTG_DIEPEMPMSK register ********************/ -#define USB_OTG_DIEPEMPMSK_INEPTXFEM_Pos (0U) -#define USB_OTG_DIEPEMPMSK_INEPTXFEM_Msk (0xFFFFUL << USB_OTG_DIEPEMPMSK_INEPTXFEM_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_DIEPEMPMSK_INEPTXFEM USB_OTG_DIEPEMPMSK_INEPTXFEM_Msk /*!< IN EP Tx FIFO empty interrupt mask bits */ - -/******************** Bit definition for USB_OTG_DEACHINT register ********************/ -#define USB_OTG_DEACHINT_IEP1INT_Pos (1U) -#define USB_OTG_DEACHINT_IEP1INT_Msk (0x1UL << USB_OTG_DEACHINT_IEP1INT_Pos) /*!< 0x00000002 */ -#define USB_OTG_DEACHINT_IEP1INT USB_OTG_DEACHINT_IEP1INT_Msk /*!< IN endpoint 1interrupt bit */ -#define USB_OTG_DEACHINT_OEP1INT_Pos (17U) -#define USB_OTG_DEACHINT_OEP1INT_Msk (0x1UL << USB_OTG_DEACHINT_OEP1INT_Pos) /*!< 0x00020000 */ -#define USB_OTG_DEACHINT_OEP1INT USB_OTG_DEACHINT_OEP1INT_Msk /*!< OUT endpoint 1 interrupt bit */ - -/******************** Bit definition for USB_OTG_GCCFG register ********************/ -#define USB_OTG_GCCFG_PWRDWN_Pos (16U) -#define USB_OTG_GCCFG_PWRDWN_Msk (0x1UL << USB_OTG_GCCFG_PWRDWN_Pos) /*!< 0x00010000 */ -#define USB_OTG_GCCFG_PWRDWN USB_OTG_GCCFG_PWRDWN_Msk /*!< Power down */ -#define USB_OTG_GCCFG_VBUSASEN_Pos (18U) -#define USB_OTG_GCCFG_VBUSASEN_Msk (0x1UL << USB_OTG_GCCFG_VBUSASEN_Pos) /*!< 0x00040000 */ -#define USB_OTG_GCCFG_VBUSASEN USB_OTG_GCCFG_VBUSASEN_Msk /*!< Enable the VBUS sensing device */ -#define USB_OTG_GCCFG_VBUSBSEN_Pos (19U) -#define USB_OTG_GCCFG_VBUSBSEN_Msk (0x1UL << USB_OTG_GCCFG_VBUSBSEN_Pos) /*!< 0x00080000 */ -#define USB_OTG_GCCFG_VBUSBSEN USB_OTG_GCCFG_VBUSBSEN_Msk /*!< Enable the VBUS sensing device */ -#define USB_OTG_GCCFG_SOFOUTEN_Pos (20U) -#define USB_OTG_GCCFG_SOFOUTEN_Msk (0x1UL << USB_OTG_GCCFG_SOFOUTEN_Pos) /*!< 0x00100000 */ -#define USB_OTG_GCCFG_SOFOUTEN USB_OTG_GCCFG_SOFOUTEN_Msk /*!< SOF output enable */ - -/******************** Bit definition for USB_OTG_DEACHINTMSK register ********************/ -#define USB_OTG_DEACHINTMSK_IEP1INTM_Pos (1U) -#define USB_OTG_DEACHINTMSK_IEP1INTM_Msk (0x1UL << USB_OTG_DEACHINTMSK_IEP1INTM_Pos) /*!< 0x00000002 */ -#define USB_OTG_DEACHINTMSK_IEP1INTM USB_OTG_DEACHINTMSK_IEP1INTM_Msk /*!< IN Endpoint 1 interrupt mask bit */ -#define USB_OTG_DEACHINTMSK_OEP1INTM_Pos (17U) -#define USB_OTG_DEACHINTMSK_OEP1INTM_Msk (0x1UL << USB_OTG_DEACHINTMSK_OEP1INTM_Pos) /*!< 0x00020000 */ -#define USB_OTG_DEACHINTMSK_OEP1INTM USB_OTG_DEACHINTMSK_OEP1INTM_Msk /*!< OUT Endpoint 1 interrupt mask bit */ - -/******************** Bit definition for USB_OTG_CID register ********************/ -#define USB_OTG_CID_PRODUCT_ID_Pos (0U) -#define USB_OTG_CID_PRODUCT_ID_Msk (0xFFFFFFFFUL << USB_OTG_CID_PRODUCT_ID_Pos) /*!< 0xFFFFFFFF */ -#define USB_OTG_CID_PRODUCT_ID USB_OTG_CID_PRODUCT_ID_Msk /*!< Product ID field */ - -/******************** Bit definition for USB_OTG_DIEPEACHMSK1 register ********************/ -#define USB_OTG_DIEPEACHMSK1_XFRCM_Pos (0U) -#define USB_OTG_DIEPEACHMSK1_XFRCM_Msk (0x1UL << USB_OTG_DIEPEACHMSK1_XFRCM_Pos) /*!< 0x00000001 */ -#define USB_OTG_DIEPEACHMSK1_XFRCM USB_OTG_DIEPEACHMSK1_XFRCM_Msk /*!< Transfer completed interrupt mask */ -#define USB_OTG_DIEPEACHMSK1_EPDM_Pos (1U) -#define USB_OTG_DIEPEACHMSK1_EPDM_Msk (0x1UL << USB_OTG_DIEPEACHMSK1_EPDM_Pos) /*!< 0x00000002 */ -#define USB_OTG_DIEPEACHMSK1_EPDM USB_OTG_DIEPEACHMSK1_EPDM_Msk /*!< Endpoint disabled interrupt mask */ -#define USB_OTG_DIEPEACHMSK1_TOM_Pos (3U) -#define USB_OTG_DIEPEACHMSK1_TOM_Msk (0x1UL << USB_OTG_DIEPEACHMSK1_TOM_Pos) /*!< 0x00000008 */ -#define USB_OTG_DIEPEACHMSK1_TOM USB_OTG_DIEPEACHMSK1_TOM_Msk /*!< Timeout condition mask (nonisochronous endpoints) */ -#define USB_OTG_DIEPEACHMSK1_ITTXFEMSK_Pos (4U) -#define USB_OTG_DIEPEACHMSK1_ITTXFEMSK_Msk (0x1UL << USB_OTG_DIEPEACHMSK1_ITTXFEMSK_Pos) /*!< 0x00000010 */ -#define USB_OTG_DIEPEACHMSK1_ITTXFEMSK USB_OTG_DIEPEACHMSK1_ITTXFEMSK_Msk /*!< IN token received when TxFIFO empty mask */ -#define USB_OTG_DIEPEACHMSK1_INEPNMM_Pos (5U) -#define USB_OTG_DIEPEACHMSK1_INEPNMM_Msk (0x1UL << USB_OTG_DIEPEACHMSK1_INEPNMM_Pos) /*!< 0x00000020 */ -#define USB_OTG_DIEPEACHMSK1_INEPNMM USB_OTG_DIEPEACHMSK1_INEPNMM_Msk /*!< IN token received with EP mismatch mask */ -#define USB_OTG_DIEPEACHMSK1_INEPNEM_Pos (6U) -#define USB_OTG_DIEPEACHMSK1_INEPNEM_Msk (0x1UL << USB_OTG_DIEPEACHMSK1_INEPNEM_Pos) /*!< 0x00000040 */ -#define USB_OTG_DIEPEACHMSK1_INEPNEM USB_OTG_DIEPEACHMSK1_INEPNEM_Msk /*!< IN endpoint NAK effective mask */ -#define USB_OTG_DIEPEACHMSK1_TXFURM_Pos (8U) -#define USB_OTG_DIEPEACHMSK1_TXFURM_Msk (0x1UL << USB_OTG_DIEPEACHMSK1_TXFURM_Pos) /*!< 0x00000100 */ -#define USB_OTG_DIEPEACHMSK1_TXFURM USB_OTG_DIEPEACHMSK1_TXFURM_Msk /*!< FIFO underrun mask */ -#define USB_OTG_DIEPEACHMSK1_BIM_Pos (9U) -#define USB_OTG_DIEPEACHMSK1_BIM_Msk (0x1UL << USB_OTG_DIEPEACHMSK1_BIM_Pos) /*!< 0x00000200 */ -#define USB_OTG_DIEPEACHMSK1_BIM USB_OTG_DIEPEACHMSK1_BIM_Msk /*!< BNA interrupt mask */ -#define USB_OTG_DIEPEACHMSK1_NAKM_Pos (13U) -#define USB_OTG_DIEPEACHMSK1_NAKM_Msk (0x1UL << USB_OTG_DIEPEACHMSK1_NAKM_Pos) /*!< 0x00002000 */ -#define USB_OTG_DIEPEACHMSK1_NAKM USB_OTG_DIEPEACHMSK1_NAKM_Msk /*!< NAK interrupt mask */ - -/******************** Bit definition for USB_OTG_HPRT register ********************/ -#define USB_OTG_HPRT_PCSTS_Pos (0U) -#define USB_OTG_HPRT_PCSTS_Msk (0x1UL << USB_OTG_HPRT_PCSTS_Pos) /*!< 0x00000001 */ -#define USB_OTG_HPRT_PCSTS USB_OTG_HPRT_PCSTS_Msk /*!< Port connect status */ -#define USB_OTG_HPRT_PCDET_Pos (1U) -#define USB_OTG_HPRT_PCDET_Msk (0x1UL << USB_OTG_HPRT_PCDET_Pos) /*!< 0x00000002 */ -#define USB_OTG_HPRT_PCDET USB_OTG_HPRT_PCDET_Msk /*!< Port connect detected */ -#define USB_OTG_HPRT_PENA_Pos (2U) -#define USB_OTG_HPRT_PENA_Msk (0x1UL << USB_OTG_HPRT_PENA_Pos) /*!< 0x00000004 */ -#define USB_OTG_HPRT_PENA USB_OTG_HPRT_PENA_Msk /*!< Port enable */ -#define USB_OTG_HPRT_PENCHNG_Pos (3U) -#define USB_OTG_HPRT_PENCHNG_Msk (0x1UL << USB_OTG_HPRT_PENCHNG_Pos) /*!< 0x00000008 */ -#define USB_OTG_HPRT_PENCHNG USB_OTG_HPRT_PENCHNG_Msk /*!< Port enable/disable change */ -#define USB_OTG_HPRT_POCA_Pos (4U) -#define USB_OTG_HPRT_POCA_Msk (0x1UL << USB_OTG_HPRT_POCA_Pos) /*!< 0x00000010 */ -#define USB_OTG_HPRT_POCA USB_OTG_HPRT_POCA_Msk /*!< Port overcurrent active */ -#define USB_OTG_HPRT_POCCHNG_Pos (5U) -#define USB_OTG_HPRT_POCCHNG_Msk (0x1UL << USB_OTG_HPRT_POCCHNG_Pos) /*!< 0x00000020 */ -#define USB_OTG_HPRT_POCCHNG USB_OTG_HPRT_POCCHNG_Msk /*!< Port overcurrent change */ -#define USB_OTG_HPRT_PRES_Pos (6U) -#define USB_OTG_HPRT_PRES_Msk (0x1UL << USB_OTG_HPRT_PRES_Pos) /*!< 0x00000040 */ -#define USB_OTG_HPRT_PRES USB_OTG_HPRT_PRES_Msk /*!< Port resume */ -#define USB_OTG_HPRT_PSUSP_Pos (7U) -#define USB_OTG_HPRT_PSUSP_Msk (0x1UL << USB_OTG_HPRT_PSUSP_Pos) /*!< 0x00000080 */ -#define USB_OTG_HPRT_PSUSP USB_OTG_HPRT_PSUSP_Msk /*!< Port suspend */ -#define USB_OTG_HPRT_PRST_Pos (8U) -#define USB_OTG_HPRT_PRST_Msk (0x1UL << USB_OTG_HPRT_PRST_Pos) /*!< 0x00000100 */ -#define USB_OTG_HPRT_PRST USB_OTG_HPRT_PRST_Msk /*!< Port reset */ - -#define USB_OTG_HPRT_PLSTS_Pos (10U) -#define USB_OTG_HPRT_PLSTS_Msk (0x3UL << USB_OTG_HPRT_PLSTS_Pos) /*!< 0x00000C00 */ -#define USB_OTG_HPRT_PLSTS USB_OTG_HPRT_PLSTS_Msk /*!< Port line status */ -#define USB_OTG_HPRT_PLSTS_0 (0x1UL << USB_OTG_HPRT_PLSTS_Pos) /*!< 0x00000400 */ -#define USB_OTG_HPRT_PLSTS_1 (0x2UL << USB_OTG_HPRT_PLSTS_Pos) /*!< 0x00000800 */ -#define USB_OTG_HPRT_PPWR_Pos (12U) -#define USB_OTG_HPRT_PPWR_Msk (0x1UL << USB_OTG_HPRT_PPWR_Pos) /*!< 0x00001000 */ -#define USB_OTG_HPRT_PPWR USB_OTG_HPRT_PPWR_Msk /*!< Port power */ - -#define USB_OTG_HPRT_PTCTL_Pos (13U) -#define USB_OTG_HPRT_PTCTL_Msk (0xFUL << USB_OTG_HPRT_PTCTL_Pos) /*!< 0x0001E000 */ -#define USB_OTG_HPRT_PTCTL USB_OTG_HPRT_PTCTL_Msk /*!< Port test control */ -#define USB_OTG_HPRT_PTCTL_0 (0x1UL << USB_OTG_HPRT_PTCTL_Pos) /*!< 0x00002000 */ -#define USB_OTG_HPRT_PTCTL_1 (0x2UL << USB_OTG_HPRT_PTCTL_Pos) /*!< 0x00004000 */ -#define USB_OTG_HPRT_PTCTL_2 (0x4UL << USB_OTG_HPRT_PTCTL_Pos) /*!< 0x00008000 */ -#define USB_OTG_HPRT_PTCTL_3 (0x8UL << USB_OTG_HPRT_PTCTL_Pos) /*!< 0x00010000 */ - -#define USB_OTG_HPRT_PSPD_Pos (17U) -#define USB_OTG_HPRT_PSPD_Msk (0x3UL << USB_OTG_HPRT_PSPD_Pos) /*!< 0x00060000 */ -#define USB_OTG_HPRT_PSPD USB_OTG_HPRT_PSPD_Msk /*!< Port speed */ -#define USB_OTG_HPRT_PSPD_0 (0x1UL << USB_OTG_HPRT_PSPD_Pos) /*!< 0x00020000 */ -#define USB_OTG_HPRT_PSPD_1 (0x2UL << USB_OTG_HPRT_PSPD_Pos) /*!< 0x00040000 */ - -/******************** Bit definition for USB_OTG_DOEPEACHMSK1 register ********************/ -#define USB_OTG_DOEPEACHMSK1_XFRCM_Pos (0U) -#define USB_OTG_DOEPEACHMSK1_XFRCM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_XFRCM_Pos) /*!< 0x00000001 */ -#define USB_OTG_DOEPEACHMSK1_XFRCM USB_OTG_DOEPEACHMSK1_XFRCM_Msk /*!< Transfer completed interrupt mask */ -#define USB_OTG_DOEPEACHMSK1_EPDM_Pos (1U) -#define USB_OTG_DOEPEACHMSK1_EPDM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_EPDM_Pos) /*!< 0x00000002 */ -#define USB_OTG_DOEPEACHMSK1_EPDM USB_OTG_DOEPEACHMSK1_EPDM_Msk /*!< Endpoint disabled interrupt mask */ -#define USB_OTG_DOEPEACHMSK1_TOM_Pos (3U) -#define USB_OTG_DOEPEACHMSK1_TOM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_TOM_Pos) /*!< 0x00000008 */ -#define USB_OTG_DOEPEACHMSK1_TOM USB_OTG_DOEPEACHMSK1_TOM_Msk /*!< Timeout condition mask */ -#define USB_OTG_DOEPEACHMSK1_ITTXFEMSK_Pos (4U) -#define USB_OTG_DOEPEACHMSK1_ITTXFEMSK_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_ITTXFEMSK_Pos) /*!< 0x00000010 */ -#define USB_OTG_DOEPEACHMSK1_ITTXFEMSK USB_OTG_DOEPEACHMSK1_ITTXFEMSK_Msk /*!< IN token received when TxFIFO empty mask */ -#define USB_OTG_DOEPEACHMSK1_INEPNMM_Pos (5U) -#define USB_OTG_DOEPEACHMSK1_INEPNMM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_INEPNMM_Pos) /*!< 0x00000020 */ -#define USB_OTG_DOEPEACHMSK1_INEPNMM USB_OTG_DOEPEACHMSK1_INEPNMM_Msk /*!< IN token received with EP mismatch mask */ -#define USB_OTG_DOEPEACHMSK1_INEPNEM_Pos (6U) -#define USB_OTG_DOEPEACHMSK1_INEPNEM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_INEPNEM_Pos) /*!< 0x00000040 */ -#define USB_OTG_DOEPEACHMSK1_INEPNEM USB_OTG_DOEPEACHMSK1_INEPNEM_Msk /*!< IN endpoint NAK effective mask */ -#define USB_OTG_DOEPEACHMSK1_TXFURM_Pos (8U) -#define USB_OTG_DOEPEACHMSK1_TXFURM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_TXFURM_Pos) /*!< 0x00000100 */ -#define USB_OTG_DOEPEACHMSK1_TXFURM USB_OTG_DOEPEACHMSK1_TXFURM_Msk /*!< OUT packet error mask */ -#define USB_OTG_DOEPEACHMSK1_BIM_Pos (9U) -#define USB_OTG_DOEPEACHMSK1_BIM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_BIM_Pos) /*!< 0x00000200 */ -#define USB_OTG_DOEPEACHMSK1_BIM USB_OTG_DOEPEACHMSK1_BIM_Msk /*!< BNA interrupt mask */ -#define USB_OTG_DOEPEACHMSK1_BERRM_Pos (12U) -#define USB_OTG_DOEPEACHMSK1_BERRM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_BERRM_Pos) /*!< 0x00001000 */ -#define USB_OTG_DOEPEACHMSK1_BERRM USB_OTG_DOEPEACHMSK1_BERRM_Msk /*!< Bubble error interrupt mask */ -#define USB_OTG_DOEPEACHMSK1_NAKM_Pos (13U) -#define USB_OTG_DOEPEACHMSK1_NAKM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_NAKM_Pos) /*!< 0x00002000 */ -#define USB_OTG_DOEPEACHMSK1_NAKM USB_OTG_DOEPEACHMSK1_NAKM_Msk /*!< NAK interrupt mask */ -#define USB_OTG_DOEPEACHMSK1_NYETM_Pos (14U) -#define USB_OTG_DOEPEACHMSK1_NYETM_Msk (0x1UL << USB_OTG_DOEPEACHMSK1_NYETM_Pos) /*!< 0x00004000 */ -#define USB_OTG_DOEPEACHMSK1_NYETM USB_OTG_DOEPEACHMSK1_NYETM_Msk /*!< NYET interrupt mask */ - -/******************** Bit definition for USB_OTG_HPTXFSIZ register ********************/ -#define USB_OTG_HPTXFSIZ_PTXSA_Pos (0U) -#define USB_OTG_HPTXFSIZ_PTXSA_Msk (0xFFFFUL << USB_OTG_HPTXFSIZ_PTXSA_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_HPTXFSIZ_PTXSA USB_OTG_HPTXFSIZ_PTXSA_Msk /*!< Host periodic TxFIFO start address */ -#define USB_OTG_HPTXFSIZ_PTXFD_Pos (16U) -#define USB_OTG_HPTXFSIZ_PTXFD_Msk (0xFFFFUL << USB_OTG_HPTXFSIZ_PTXFD_Pos) /*!< 0xFFFF0000 */ -#define USB_OTG_HPTXFSIZ_PTXFD USB_OTG_HPTXFSIZ_PTXFD_Msk /*!< Host periodic TxFIFO depth */ - -/******************** Bit definition for USB_OTG_DIEPCTL register ********************/ -#define USB_OTG_DIEPCTL_MPSIZ_Pos (0U) -#define USB_OTG_DIEPCTL_MPSIZ_Msk (0x7FFUL << USB_OTG_DIEPCTL_MPSIZ_Pos) /*!< 0x000007FF */ -#define USB_OTG_DIEPCTL_MPSIZ USB_OTG_DIEPCTL_MPSIZ_Msk /*!< Maximum packet size */ -#define USB_OTG_DIEPCTL_USBAEP_Pos (15U) -#define USB_OTG_DIEPCTL_USBAEP_Msk (0x1UL << USB_OTG_DIEPCTL_USBAEP_Pos) /*!< 0x00008000 */ -#define USB_OTG_DIEPCTL_USBAEP USB_OTG_DIEPCTL_USBAEP_Msk /*!< USB active endpoint */ -#define USB_OTG_DIEPCTL_EONUM_DPID_Pos (16U) -#define USB_OTG_DIEPCTL_EONUM_DPID_Msk (0x1UL << USB_OTG_DIEPCTL_EONUM_DPID_Pos) /*!< 0x00010000 */ -#define USB_OTG_DIEPCTL_EONUM_DPID USB_OTG_DIEPCTL_EONUM_DPID_Msk /*!< Even/odd frame */ -#define USB_OTG_DIEPCTL_NAKSTS_Pos (17U) -#define USB_OTG_DIEPCTL_NAKSTS_Msk (0x1UL << USB_OTG_DIEPCTL_NAKSTS_Pos) /*!< 0x00020000 */ -#define USB_OTG_DIEPCTL_NAKSTS USB_OTG_DIEPCTL_NAKSTS_Msk /*!< NAK status */ - -#define USB_OTG_DIEPCTL_EPTYP_Pos (18U) -#define USB_OTG_DIEPCTL_EPTYP_Msk (0x3UL << USB_OTG_DIEPCTL_EPTYP_Pos) /*!< 0x000C0000 */ -#define USB_OTG_DIEPCTL_EPTYP USB_OTG_DIEPCTL_EPTYP_Msk /*!< Endpoint type */ -#define USB_OTG_DIEPCTL_EPTYP_0 (0x1UL << USB_OTG_DIEPCTL_EPTYP_Pos) /*!< 0x00040000 */ -#define USB_OTG_DIEPCTL_EPTYP_1 (0x2UL << USB_OTG_DIEPCTL_EPTYP_Pos) /*!< 0x00080000 */ -#define USB_OTG_DIEPCTL_STALL_Pos (21U) -#define USB_OTG_DIEPCTL_STALL_Msk (0x1UL << USB_OTG_DIEPCTL_STALL_Pos) /*!< 0x00200000 */ -#define USB_OTG_DIEPCTL_STALL USB_OTG_DIEPCTL_STALL_Msk /*!< STALL handshake */ - -#define USB_OTG_DIEPCTL_TXFNUM_Pos (22U) -#define USB_OTG_DIEPCTL_TXFNUM_Msk (0xFUL << USB_OTG_DIEPCTL_TXFNUM_Pos) /*!< 0x03C00000 */ -#define USB_OTG_DIEPCTL_TXFNUM USB_OTG_DIEPCTL_TXFNUM_Msk /*!< TxFIFO number */ -#define USB_OTG_DIEPCTL_TXFNUM_0 (0x1UL << USB_OTG_DIEPCTL_TXFNUM_Pos) /*!< 0x00400000 */ -#define USB_OTG_DIEPCTL_TXFNUM_1 (0x2UL << USB_OTG_DIEPCTL_TXFNUM_Pos) /*!< 0x00800000 */ -#define USB_OTG_DIEPCTL_TXFNUM_2 (0x4UL << USB_OTG_DIEPCTL_TXFNUM_Pos) /*!< 0x01000000 */ -#define USB_OTG_DIEPCTL_TXFNUM_3 (0x8UL << USB_OTG_DIEPCTL_TXFNUM_Pos) /*!< 0x02000000 */ -#define USB_OTG_DIEPCTL_CNAK_Pos (26U) -#define USB_OTG_DIEPCTL_CNAK_Msk (0x1UL << USB_OTG_DIEPCTL_CNAK_Pos) /*!< 0x04000000 */ -#define USB_OTG_DIEPCTL_CNAK USB_OTG_DIEPCTL_CNAK_Msk /*!< Clear NAK */ -#define USB_OTG_DIEPCTL_SNAK_Pos (27U) -#define USB_OTG_DIEPCTL_SNAK_Msk (0x1UL << USB_OTG_DIEPCTL_SNAK_Pos) /*!< 0x08000000 */ -#define USB_OTG_DIEPCTL_SNAK USB_OTG_DIEPCTL_SNAK_Msk /*!< Set NAK */ -#define USB_OTG_DIEPCTL_SD0PID_SEVNFRM_Pos (28U) -#define USB_OTG_DIEPCTL_SD0PID_SEVNFRM_Msk (0x1UL << USB_OTG_DIEPCTL_SD0PID_SEVNFRM_Pos) /*!< 0x10000000 */ -#define USB_OTG_DIEPCTL_SD0PID_SEVNFRM USB_OTG_DIEPCTL_SD0PID_SEVNFRM_Msk /*!< Set DATA0 PID */ -#define USB_OTG_DIEPCTL_SODDFRM_Pos (29U) -#define USB_OTG_DIEPCTL_SODDFRM_Msk (0x1UL << USB_OTG_DIEPCTL_SODDFRM_Pos) /*!< 0x20000000 */ -#define USB_OTG_DIEPCTL_SODDFRM USB_OTG_DIEPCTL_SODDFRM_Msk /*!< Set odd frame */ -#define USB_OTG_DIEPCTL_EPDIS_Pos (30U) -#define USB_OTG_DIEPCTL_EPDIS_Msk (0x1UL << USB_OTG_DIEPCTL_EPDIS_Pos) /*!< 0x40000000 */ -#define USB_OTG_DIEPCTL_EPDIS USB_OTG_DIEPCTL_EPDIS_Msk /*!< Endpoint disable */ -#define USB_OTG_DIEPCTL_EPENA_Pos (31U) -#define USB_OTG_DIEPCTL_EPENA_Msk (0x1UL << USB_OTG_DIEPCTL_EPENA_Pos) /*!< 0x80000000 */ -#define USB_OTG_DIEPCTL_EPENA USB_OTG_DIEPCTL_EPENA_Msk /*!< Endpoint enable */ - -/******************** Bit definition for USB_OTG_HCCHAR register ********************/ -#define USB_OTG_HCCHAR_MPSIZ_Pos (0U) -#define USB_OTG_HCCHAR_MPSIZ_Msk (0x7FFUL << USB_OTG_HCCHAR_MPSIZ_Pos) /*!< 0x000007FF */ -#define USB_OTG_HCCHAR_MPSIZ USB_OTG_HCCHAR_MPSIZ_Msk /*!< Maximum packet size */ - -#define USB_OTG_HCCHAR_EPNUM_Pos (11U) -#define USB_OTG_HCCHAR_EPNUM_Msk (0xFUL << USB_OTG_HCCHAR_EPNUM_Pos) /*!< 0x00007800 */ -#define USB_OTG_HCCHAR_EPNUM USB_OTG_HCCHAR_EPNUM_Msk /*!< Endpoint number */ -#define USB_OTG_HCCHAR_EPNUM_0 (0x1UL << USB_OTG_HCCHAR_EPNUM_Pos) /*!< 0x00000800 */ -#define USB_OTG_HCCHAR_EPNUM_1 (0x2UL << USB_OTG_HCCHAR_EPNUM_Pos) /*!< 0x00001000 */ -#define USB_OTG_HCCHAR_EPNUM_2 (0x4UL << USB_OTG_HCCHAR_EPNUM_Pos) /*!< 0x00002000 */ -#define USB_OTG_HCCHAR_EPNUM_3 (0x8UL << USB_OTG_HCCHAR_EPNUM_Pos) /*!< 0x00004000 */ -#define USB_OTG_HCCHAR_EPDIR_Pos (15U) -#define USB_OTG_HCCHAR_EPDIR_Msk (0x1UL << USB_OTG_HCCHAR_EPDIR_Pos) /*!< 0x00008000 */ -#define USB_OTG_HCCHAR_EPDIR USB_OTG_HCCHAR_EPDIR_Msk /*!< Endpoint direction */ -#define USB_OTG_HCCHAR_LSDEV_Pos (17U) -#define USB_OTG_HCCHAR_LSDEV_Msk (0x1UL << USB_OTG_HCCHAR_LSDEV_Pos) /*!< 0x00020000 */ -#define USB_OTG_HCCHAR_LSDEV USB_OTG_HCCHAR_LSDEV_Msk /*!< Low-speed device */ - -#define USB_OTG_HCCHAR_EPTYP_Pos (18U) -#define USB_OTG_HCCHAR_EPTYP_Msk (0x3UL << USB_OTG_HCCHAR_EPTYP_Pos) /*!< 0x000C0000 */ -#define USB_OTG_HCCHAR_EPTYP USB_OTG_HCCHAR_EPTYP_Msk /*!< Endpoint type */ -#define USB_OTG_HCCHAR_EPTYP_0 (0x1UL << USB_OTG_HCCHAR_EPTYP_Pos) /*!< 0x00040000 */ -#define USB_OTG_HCCHAR_EPTYP_1 (0x2UL << USB_OTG_HCCHAR_EPTYP_Pos) /*!< 0x00080000 */ - -#define USB_OTG_HCCHAR_MC_Pos (20U) -#define USB_OTG_HCCHAR_MC_Msk (0x3UL << USB_OTG_HCCHAR_MC_Pos) /*!< 0x00300000 */ -#define USB_OTG_HCCHAR_MC USB_OTG_HCCHAR_MC_Msk /*!< Multi Count (MC) / Error Count (EC) */ -#define USB_OTG_HCCHAR_MC_0 (0x1UL << USB_OTG_HCCHAR_MC_Pos) /*!< 0x00100000 */ -#define USB_OTG_HCCHAR_MC_1 (0x2UL << USB_OTG_HCCHAR_MC_Pos) /*!< 0x00200000 */ - -#define USB_OTG_HCCHAR_DAD_Pos (22U) -#define USB_OTG_HCCHAR_DAD_Msk (0x7FUL << USB_OTG_HCCHAR_DAD_Pos) /*!< 0x1FC00000 */ -#define USB_OTG_HCCHAR_DAD USB_OTG_HCCHAR_DAD_Msk /*!< Device address */ -#define USB_OTG_HCCHAR_DAD_0 (0x01UL << USB_OTG_HCCHAR_DAD_Pos) /*!< 0x00400000 */ -#define USB_OTG_HCCHAR_DAD_1 (0x02UL << USB_OTG_HCCHAR_DAD_Pos) /*!< 0x00800000 */ -#define USB_OTG_HCCHAR_DAD_2 (0x04UL << USB_OTG_HCCHAR_DAD_Pos) /*!< 0x01000000 */ -#define USB_OTG_HCCHAR_DAD_3 (0x08UL << USB_OTG_HCCHAR_DAD_Pos) /*!< 0x02000000 */ -#define USB_OTG_HCCHAR_DAD_4 (0x10UL << USB_OTG_HCCHAR_DAD_Pos) /*!< 0x04000000 */ -#define USB_OTG_HCCHAR_DAD_5 (0x20UL << USB_OTG_HCCHAR_DAD_Pos) /*!< 0x08000000 */ -#define USB_OTG_HCCHAR_DAD_6 (0x40UL << USB_OTG_HCCHAR_DAD_Pos) /*!< 0x10000000 */ -#define USB_OTG_HCCHAR_ODDFRM_Pos (29U) -#define USB_OTG_HCCHAR_ODDFRM_Msk (0x1UL << USB_OTG_HCCHAR_ODDFRM_Pos) /*!< 0x20000000 */ -#define USB_OTG_HCCHAR_ODDFRM USB_OTG_HCCHAR_ODDFRM_Msk /*!< Odd frame */ -#define USB_OTG_HCCHAR_CHDIS_Pos (30U) -#define USB_OTG_HCCHAR_CHDIS_Msk (0x1UL << USB_OTG_HCCHAR_CHDIS_Pos) /*!< 0x40000000 */ -#define USB_OTG_HCCHAR_CHDIS USB_OTG_HCCHAR_CHDIS_Msk /*!< Channel disable */ -#define USB_OTG_HCCHAR_CHENA_Pos (31U) -#define USB_OTG_HCCHAR_CHENA_Msk (0x1UL << USB_OTG_HCCHAR_CHENA_Pos) /*!< 0x80000000 */ -#define USB_OTG_HCCHAR_CHENA USB_OTG_HCCHAR_CHENA_Msk /*!< Channel enable */ - -/******************** Bit definition for USB_OTG_HCSPLT register ********************/ - -#define USB_OTG_HCSPLT_PRTADDR_Pos (0U) -#define USB_OTG_HCSPLT_PRTADDR_Msk (0x7FUL << USB_OTG_HCSPLT_PRTADDR_Pos) /*!< 0x0000007F */ -#define USB_OTG_HCSPLT_PRTADDR USB_OTG_HCSPLT_PRTADDR_Msk /*!< Port address */ -#define USB_OTG_HCSPLT_PRTADDR_0 (0x01UL << USB_OTG_HCSPLT_PRTADDR_Pos) /*!< 0x00000001 */ -#define USB_OTG_HCSPLT_PRTADDR_1 (0x02UL << USB_OTG_HCSPLT_PRTADDR_Pos) /*!< 0x00000002 */ -#define USB_OTG_HCSPLT_PRTADDR_2 (0x04UL << USB_OTG_HCSPLT_PRTADDR_Pos) /*!< 0x00000004 */ -#define USB_OTG_HCSPLT_PRTADDR_3 (0x08UL << USB_OTG_HCSPLT_PRTADDR_Pos) /*!< 0x00000008 */ -#define USB_OTG_HCSPLT_PRTADDR_4 (0x10UL << USB_OTG_HCSPLT_PRTADDR_Pos) /*!< 0x00000010 */ -#define USB_OTG_HCSPLT_PRTADDR_5 (0x20UL << USB_OTG_HCSPLT_PRTADDR_Pos) /*!< 0x00000020 */ -#define USB_OTG_HCSPLT_PRTADDR_6 (0x40UL << USB_OTG_HCSPLT_PRTADDR_Pos) /*!< 0x00000040 */ - -#define USB_OTG_HCSPLT_HUBADDR_Pos (7U) -#define USB_OTG_HCSPLT_HUBADDR_Msk (0x7FUL << USB_OTG_HCSPLT_HUBADDR_Pos) /*!< 0x00003F80 */ -#define USB_OTG_HCSPLT_HUBADDR USB_OTG_HCSPLT_HUBADDR_Msk /*!< Hub address */ -#define USB_OTG_HCSPLT_HUBADDR_0 (0x01UL << USB_OTG_HCSPLT_HUBADDR_Pos) /*!< 0x00000080 */ -#define USB_OTG_HCSPLT_HUBADDR_1 (0x02UL << USB_OTG_HCSPLT_HUBADDR_Pos) /*!< 0x00000100 */ -#define USB_OTG_HCSPLT_HUBADDR_2 (0x04UL << USB_OTG_HCSPLT_HUBADDR_Pos) /*!< 0x00000200 */ -#define USB_OTG_HCSPLT_HUBADDR_3 (0x08UL << USB_OTG_HCSPLT_HUBADDR_Pos) /*!< 0x00000400 */ -#define USB_OTG_HCSPLT_HUBADDR_4 (0x10UL << USB_OTG_HCSPLT_HUBADDR_Pos) /*!< 0x00000800 */ -#define USB_OTG_HCSPLT_HUBADDR_5 (0x20UL << USB_OTG_HCSPLT_HUBADDR_Pos) /*!< 0x00001000 */ -#define USB_OTG_HCSPLT_HUBADDR_6 (0x40UL << USB_OTG_HCSPLT_HUBADDR_Pos) /*!< 0x00002000 */ - -#define USB_OTG_HCSPLT_XACTPOS_Pos (14U) -#define USB_OTG_HCSPLT_XACTPOS_Msk (0x3UL << USB_OTG_HCSPLT_XACTPOS_Pos) /*!< 0x0000C000 */ -#define USB_OTG_HCSPLT_XACTPOS USB_OTG_HCSPLT_XACTPOS_Msk /*!< XACTPOS */ -#define USB_OTG_HCSPLT_XACTPOS_0 (0x1UL << USB_OTG_HCSPLT_XACTPOS_Pos) /*!< 0x00004000 */ -#define USB_OTG_HCSPLT_XACTPOS_1 (0x2UL << USB_OTG_HCSPLT_XACTPOS_Pos) /*!< 0x00008000 */ -#define USB_OTG_HCSPLT_COMPLSPLT_Pos (16U) -#define USB_OTG_HCSPLT_COMPLSPLT_Msk (0x1UL << USB_OTG_HCSPLT_COMPLSPLT_Pos) /*!< 0x00010000 */ -#define USB_OTG_HCSPLT_COMPLSPLT USB_OTG_HCSPLT_COMPLSPLT_Msk /*!< Do complete split */ -#define USB_OTG_HCSPLT_SPLITEN_Pos (31U) -#define USB_OTG_HCSPLT_SPLITEN_Msk (0x1UL << USB_OTG_HCSPLT_SPLITEN_Pos) /*!< 0x80000000 */ -#define USB_OTG_HCSPLT_SPLITEN USB_OTG_HCSPLT_SPLITEN_Msk /*!< Split enable */ - -/******************** Bit definition for USB_OTG_HCINT register ********************/ -#define USB_OTG_HCINT_XFRC_Pos (0U) -#define USB_OTG_HCINT_XFRC_Msk (0x1UL << USB_OTG_HCINT_XFRC_Pos) /*!< 0x00000001 */ -#define USB_OTG_HCINT_XFRC USB_OTG_HCINT_XFRC_Msk /*!< Transfer completed */ -#define USB_OTG_HCINT_CHH_Pos (1U) -#define USB_OTG_HCINT_CHH_Msk (0x1UL << USB_OTG_HCINT_CHH_Pos) /*!< 0x00000002 */ -#define USB_OTG_HCINT_CHH USB_OTG_HCINT_CHH_Msk /*!< Channel halted */ -#define USB_OTG_HCINT_AHBERR_Pos (2U) -#define USB_OTG_HCINT_AHBERR_Msk (0x1UL << USB_OTG_HCINT_AHBERR_Pos) /*!< 0x00000004 */ -#define USB_OTG_HCINT_AHBERR USB_OTG_HCINT_AHBERR_Msk /*!< AHB error */ -#define USB_OTG_HCINT_STALL_Pos (3U) -#define USB_OTG_HCINT_STALL_Msk (0x1UL << USB_OTG_HCINT_STALL_Pos) /*!< 0x00000008 */ -#define USB_OTG_HCINT_STALL USB_OTG_HCINT_STALL_Msk /*!< STALL response received interrupt */ -#define USB_OTG_HCINT_NAK_Pos (4U) -#define USB_OTG_HCINT_NAK_Msk (0x1UL << USB_OTG_HCINT_NAK_Pos) /*!< 0x00000010 */ -#define USB_OTG_HCINT_NAK USB_OTG_HCINT_NAK_Msk /*!< NAK response received interrupt */ -#define USB_OTG_HCINT_ACK_Pos (5U) -#define USB_OTG_HCINT_ACK_Msk (0x1UL << USB_OTG_HCINT_ACK_Pos) /*!< 0x00000020 */ -#define USB_OTG_HCINT_ACK USB_OTG_HCINT_ACK_Msk /*!< ACK response received/transmitted interrupt */ -#define USB_OTG_HCINT_NYET_Pos (6U) -#define USB_OTG_HCINT_NYET_Msk (0x1UL << USB_OTG_HCINT_NYET_Pos) /*!< 0x00000040 */ -#define USB_OTG_HCINT_NYET USB_OTG_HCINT_NYET_Msk /*!< Response received interrupt */ -#define USB_OTG_HCINT_TXERR_Pos (7U) -#define USB_OTG_HCINT_TXERR_Msk (0x1UL << USB_OTG_HCINT_TXERR_Pos) /*!< 0x00000080 */ -#define USB_OTG_HCINT_TXERR USB_OTG_HCINT_TXERR_Msk /*!< Transaction error */ -#define USB_OTG_HCINT_BBERR_Pos (8U) -#define USB_OTG_HCINT_BBERR_Msk (0x1UL << USB_OTG_HCINT_BBERR_Pos) /*!< 0x00000100 */ -#define USB_OTG_HCINT_BBERR USB_OTG_HCINT_BBERR_Msk /*!< Babble error */ -#define USB_OTG_HCINT_FRMOR_Pos (9U) -#define USB_OTG_HCINT_FRMOR_Msk (0x1UL << USB_OTG_HCINT_FRMOR_Pos) /*!< 0x00000200 */ -#define USB_OTG_HCINT_FRMOR USB_OTG_HCINT_FRMOR_Msk /*!< Frame overrun */ -#define USB_OTG_HCINT_DTERR_Pos (10U) -#define USB_OTG_HCINT_DTERR_Msk (0x1UL << USB_OTG_HCINT_DTERR_Pos) /*!< 0x00000400 */ -#define USB_OTG_HCINT_DTERR USB_OTG_HCINT_DTERR_Msk /*!< Data toggle error */ - -/******************** Bit definition for USB_OTG_DIEPINT register ********************/ -#define USB_OTG_DIEPINT_XFRC_Pos (0U) -#define USB_OTG_DIEPINT_XFRC_Msk (0x1UL << USB_OTG_DIEPINT_XFRC_Pos) /*!< 0x00000001 */ -#define USB_OTG_DIEPINT_XFRC USB_OTG_DIEPINT_XFRC_Msk /*!< Transfer completed interrupt */ -#define USB_OTG_DIEPINT_EPDISD_Pos (1U) -#define USB_OTG_DIEPINT_EPDISD_Msk (0x1UL << USB_OTG_DIEPINT_EPDISD_Pos) /*!< 0x00000002 */ -#define USB_OTG_DIEPINT_EPDISD USB_OTG_DIEPINT_EPDISD_Msk /*!< Endpoint disabled interrupt */ -#define USB_OTG_DIEPINT_AHBERR_Pos (2U) -#define USB_OTG_DIEPINT_AHBERR_Msk (0x1UL << USB_OTG_DIEPINT_AHBERR_Pos) /*!< 0x00000004 */ -#define USB_OTG_DIEPINT_AHBERR USB_OTG_DIEPINT_AHBERR_Msk /*!< AHB Error (AHBErr) during an IN transaction */ -#define USB_OTG_DIEPINT_TOC_Pos (3U) -#define USB_OTG_DIEPINT_TOC_Msk (0x1UL << USB_OTG_DIEPINT_TOC_Pos) /*!< 0x00000008 */ -#define USB_OTG_DIEPINT_TOC USB_OTG_DIEPINT_TOC_Msk /*!< Timeout condition */ -#define USB_OTG_DIEPINT_ITTXFE_Pos (4U) -#define USB_OTG_DIEPINT_ITTXFE_Msk (0x1UL << USB_OTG_DIEPINT_ITTXFE_Pos) /*!< 0x00000010 */ -#define USB_OTG_DIEPINT_ITTXFE USB_OTG_DIEPINT_ITTXFE_Msk /*!< IN token received when TxFIFO is empty */ -#define USB_OTG_DIEPINT_INEPNM_Pos (5U) -#define USB_OTG_DIEPINT_INEPNM_Msk (0x1UL << USB_OTG_DIEPINT_INEPNM_Pos) /*!< 0x00000004 */ -#define USB_OTG_DIEPINT_INEPNM USB_OTG_DIEPINT_INEPNM_Msk /*!< IN token received with EP mismatch */ -#define USB_OTG_DIEPINT_INEPNE_Pos (6U) -#define USB_OTG_DIEPINT_INEPNE_Msk (0x1UL << USB_OTG_DIEPINT_INEPNE_Pos) /*!< 0x00000040 */ -#define USB_OTG_DIEPINT_INEPNE USB_OTG_DIEPINT_INEPNE_Msk /*!< IN endpoint NAK effective */ -#define USB_OTG_DIEPINT_TXFE_Pos (7U) -#define USB_OTG_DIEPINT_TXFE_Msk (0x1UL << USB_OTG_DIEPINT_TXFE_Pos) /*!< 0x00000080 */ -#define USB_OTG_DIEPINT_TXFE USB_OTG_DIEPINT_TXFE_Msk /*!< Transmit FIFO empty */ -#define USB_OTG_DIEPINT_TXFIFOUDRN_Pos (8U) -#define USB_OTG_DIEPINT_TXFIFOUDRN_Msk (0x1UL << USB_OTG_DIEPINT_TXFIFOUDRN_Pos) /*!< 0x00000100 */ -#define USB_OTG_DIEPINT_TXFIFOUDRN USB_OTG_DIEPINT_TXFIFOUDRN_Msk /*!< Transmit Fifo Underrun */ -#define USB_OTG_DIEPINT_BNA_Pos (9U) -#define USB_OTG_DIEPINT_BNA_Msk (0x1UL << USB_OTG_DIEPINT_BNA_Pos) /*!< 0x00000200 */ -#define USB_OTG_DIEPINT_BNA USB_OTG_DIEPINT_BNA_Msk /*!< Buffer not available interrupt */ -#define USB_OTG_DIEPINT_PKTDRPSTS_Pos (11U) -#define USB_OTG_DIEPINT_PKTDRPSTS_Msk (0x1UL << USB_OTG_DIEPINT_PKTDRPSTS_Pos) /*!< 0x00000800 */ -#define USB_OTG_DIEPINT_PKTDRPSTS USB_OTG_DIEPINT_PKTDRPSTS_Msk /*!< Packet dropped status */ -#define USB_OTG_DIEPINT_BERR_Pos (12U) -#define USB_OTG_DIEPINT_BERR_Msk (0x1UL << USB_OTG_DIEPINT_BERR_Pos) /*!< 0x00001000 */ -#define USB_OTG_DIEPINT_BERR USB_OTG_DIEPINT_BERR_Msk /*!< Babble error interrupt */ -#define USB_OTG_DIEPINT_NAK_Pos (13U) -#define USB_OTG_DIEPINT_NAK_Msk (0x1UL << USB_OTG_DIEPINT_NAK_Pos) /*!< 0x00002000 */ -#define USB_OTG_DIEPINT_NAK USB_OTG_DIEPINT_NAK_Msk /*!< NAK interrupt */ - -/******************** Bit definition for USB_OTG_HCINTMSK register ********************/ -#define USB_OTG_HCINTMSK_XFRCM_Pos (0U) -#define USB_OTG_HCINTMSK_XFRCM_Msk (0x1UL << USB_OTG_HCINTMSK_XFRCM_Pos) /*!< 0x00000001 */ -#define USB_OTG_HCINTMSK_XFRCM USB_OTG_HCINTMSK_XFRCM_Msk /*!< Transfer completed mask */ -#define USB_OTG_HCINTMSK_CHHM_Pos (1U) -#define USB_OTG_HCINTMSK_CHHM_Msk (0x1UL << USB_OTG_HCINTMSK_CHHM_Pos) /*!< 0x00000002 */ -#define USB_OTG_HCINTMSK_CHHM USB_OTG_HCINTMSK_CHHM_Msk /*!< Channel halted mask */ -#define USB_OTG_HCINTMSK_AHBERR_Pos (2U) -#define USB_OTG_HCINTMSK_AHBERR_Msk (0x1UL << USB_OTG_HCINTMSK_AHBERR_Pos) /*!< 0x00000004 */ -#define USB_OTG_HCINTMSK_AHBERR USB_OTG_HCINTMSK_AHBERR_Msk /*!< AHB error */ -#define USB_OTG_HCINTMSK_STALLM_Pos (3U) -#define USB_OTG_HCINTMSK_STALLM_Msk (0x1UL << USB_OTG_HCINTMSK_STALLM_Pos) /*!< 0x00000008 */ -#define USB_OTG_HCINTMSK_STALLM USB_OTG_HCINTMSK_STALLM_Msk /*!< STALL response received interrupt mask */ -#define USB_OTG_HCINTMSK_NAKM_Pos (4U) -#define USB_OTG_HCINTMSK_NAKM_Msk (0x1UL << USB_OTG_HCINTMSK_NAKM_Pos) /*!< 0x00000010 */ -#define USB_OTG_HCINTMSK_NAKM USB_OTG_HCINTMSK_NAKM_Msk /*!< NAK response received interrupt mask */ -#define USB_OTG_HCINTMSK_ACKM_Pos (5U) -#define USB_OTG_HCINTMSK_ACKM_Msk (0x1UL << USB_OTG_HCINTMSK_ACKM_Pos) /*!< 0x00000020 */ -#define USB_OTG_HCINTMSK_ACKM USB_OTG_HCINTMSK_ACKM_Msk /*!< ACK response received/transmitted interrupt mask */ -#define USB_OTG_HCINTMSK_NYET_Pos (6U) -#define USB_OTG_HCINTMSK_NYET_Msk (0x1UL << USB_OTG_HCINTMSK_NYET_Pos) /*!< 0x00000040 */ -#define USB_OTG_HCINTMSK_NYET USB_OTG_HCINTMSK_NYET_Msk /*!< response received interrupt mask */ -#define USB_OTG_HCINTMSK_TXERRM_Pos (7U) -#define USB_OTG_HCINTMSK_TXERRM_Msk (0x1UL << USB_OTG_HCINTMSK_TXERRM_Pos) /*!< 0x00000080 */ -#define USB_OTG_HCINTMSK_TXERRM USB_OTG_HCINTMSK_TXERRM_Msk /*!< Transaction error mask */ -#define USB_OTG_HCINTMSK_BBERRM_Pos (8U) -#define USB_OTG_HCINTMSK_BBERRM_Msk (0x1UL << USB_OTG_HCINTMSK_BBERRM_Pos) /*!< 0x00000100 */ -#define USB_OTG_HCINTMSK_BBERRM USB_OTG_HCINTMSK_BBERRM_Msk /*!< Babble error mask */ -#define USB_OTG_HCINTMSK_FRMORM_Pos (9U) -#define USB_OTG_HCINTMSK_FRMORM_Msk (0x1UL << USB_OTG_HCINTMSK_FRMORM_Pos) /*!< 0x00000200 */ -#define USB_OTG_HCINTMSK_FRMORM USB_OTG_HCINTMSK_FRMORM_Msk /*!< Frame overrun mask */ -#define USB_OTG_HCINTMSK_DTERRM_Pos (10U) -#define USB_OTG_HCINTMSK_DTERRM_Msk (0x1UL << USB_OTG_HCINTMSK_DTERRM_Pos) /*!< 0x00000400 */ -#define USB_OTG_HCINTMSK_DTERRM USB_OTG_HCINTMSK_DTERRM_Msk /*!< Data toggle error mask */ - -/******************** Bit definition for USB_OTG_DIEPTSIZ register ********************/ - -#define USB_OTG_DIEPTSIZ_XFRSIZ_Pos (0U) -#define USB_OTG_DIEPTSIZ_XFRSIZ_Msk (0x7FFFFUL << USB_OTG_DIEPTSIZ_XFRSIZ_Pos) /*!< 0x0007FFFF */ -#define USB_OTG_DIEPTSIZ_XFRSIZ USB_OTG_DIEPTSIZ_XFRSIZ_Msk /*!< Transfer size */ -#define USB_OTG_DIEPTSIZ_PKTCNT_Pos (19U) -#define USB_OTG_DIEPTSIZ_PKTCNT_Msk (0x3FFUL << USB_OTG_DIEPTSIZ_PKTCNT_Pos) /*!< 0x1FF80000 */ -#define USB_OTG_DIEPTSIZ_PKTCNT USB_OTG_DIEPTSIZ_PKTCNT_Msk /*!< Packet count */ -#define USB_OTG_DIEPTSIZ_MULCNT_Pos (29U) -#define USB_OTG_DIEPTSIZ_MULCNT_Msk (0x3UL << USB_OTG_DIEPTSIZ_MULCNT_Pos) /*!< 0x60000000 */ -#define USB_OTG_DIEPTSIZ_MULCNT USB_OTG_DIEPTSIZ_MULCNT_Msk /*!< Packet count */ -/******************** Bit definition for USB_OTG_HCTSIZ register ********************/ -#define USB_OTG_HCTSIZ_XFRSIZ_Pos (0U) -#define USB_OTG_HCTSIZ_XFRSIZ_Msk (0x7FFFFUL << USB_OTG_HCTSIZ_XFRSIZ_Pos) /*!< 0x0007FFFF */ -#define USB_OTG_HCTSIZ_XFRSIZ USB_OTG_HCTSIZ_XFRSIZ_Msk /*!< Transfer size */ -#define USB_OTG_HCTSIZ_PKTCNT_Pos (19U) -#define USB_OTG_HCTSIZ_PKTCNT_Msk (0x3FFUL << USB_OTG_HCTSIZ_PKTCNT_Pos) /*!< 0x1FF80000 */ -#define USB_OTG_HCTSIZ_PKTCNT USB_OTG_HCTSIZ_PKTCNT_Msk /*!< Packet count */ -#define USB_OTG_HCTSIZ_DOPING_Pos (31U) -#define USB_OTG_HCTSIZ_DOPING_Msk (0x1UL << USB_OTG_HCTSIZ_DOPING_Pos) /*!< 0x80000000 */ -#define USB_OTG_HCTSIZ_DOPING USB_OTG_HCTSIZ_DOPING_Msk /*!< Do PING */ -#define USB_OTG_HCTSIZ_DPID_Pos (29U) -#define USB_OTG_HCTSIZ_DPID_Msk (0x3UL << USB_OTG_HCTSIZ_DPID_Pos) /*!< 0x60000000 */ -#define USB_OTG_HCTSIZ_DPID USB_OTG_HCTSIZ_DPID_Msk /*!< Data PID */ -#define USB_OTG_HCTSIZ_DPID_0 (0x1UL << USB_OTG_HCTSIZ_DPID_Pos) /*!< 0x20000000 */ -#define USB_OTG_HCTSIZ_DPID_1 (0x2UL << USB_OTG_HCTSIZ_DPID_Pos) /*!< 0x40000000 */ - -/******************** Bit definition for USB_OTG_DIEPDMA register ********************/ -#define USB_OTG_DIEPDMA_DMAADDR_Pos (0U) -#define USB_OTG_DIEPDMA_DMAADDR_Msk (0xFFFFFFFFUL << USB_OTG_DIEPDMA_DMAADDR_Pos) /*!< 0xFFFFFFFF */ -#define USB_OTG_DIEPDMA_DMAADDR USB_OTG_DIEPDMA_DMAADDR_Msk /*!< DMA address */ - -/******************** Bit definition for USB_OTG_HCDMA register ********************/ -#define USB_OTG_HCDMA_DMAADDR_Pos (0U) -#define USB_OTG_HCDMA_DMAADDR_Msk (0xFFFFFFFFUL << USB_OTG_HCDMA_DMAADDR_Pos) /*!< 0xFFFFFFFF */ -#define USB_OTG_HCDMA_DMAADDR USB_OTG_HCDMA_DMAADDR_Msk /*!< DMA address */ - -/******************** Bit definition for USB_OTG_DTXFSTS register ********************/ -#define USB_OTG_DTXFSTS_INEPTFSAV_Pos (0U) -#define USB_OTG_DTXFSTS_INEPTFSAV_Msk (0xFFFFUL << USB_OTG_DTXFSTS_INEPTFSAV_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_DTXFSTS_INEPTFSAV USB_OTG_DTXFSTS_INEPTFSAV_Msk /*!< IN endpoint TxFIFO space available */ - -/******************** Bit definition for USB_OTG_DIEPTXF register ********************/ -#define USB_OTG_DIEPTXF_INEPTXSA_Pos (0U) -#define USB_OTG_DIEPTXF_INEPTXSA_Msk (0xFFFFUL << USB_OTG_DIEPTXF_INEPTXSA_Pos) /*!< 0x0000FFFF */ -#define USB_OTG_DIEPTXF_INEPTXSA USB_OTG_DIEPTXF_INEPTXSA_Msk /*!< IN endpoint FIFOx transmit RAM start address */ -#define USB_OTG_DIEPTXF_INEPTXFD_Pos (16U) -#define USB_OTG_DIEPTXF_INEPTXFD_Msk (0xFFFFUL << USB_OTG_DIEPTXF_INEPTXFD_Pos) /*!< 0xFFFF0000 */ -#define USB_OTG_DIEPTXF_INEPTXFD USB_OTG_DIEPTXF_INEPTXFD_Msk /*!< IN endpoint TxFIFO depth */ - -/******************** Bit definition for USB_OTG_DOEPCTL register ********************/ - -#define USB_OTG_DOEPCTL_MPSIZ_Pos (0U) -#define USB_OTG_DOEPCTL_MPSIZ_Msk (0x7FFUL << USB_OTG_DOEPCTL_MPSIZ_Pos) /*!< 0x000007FF */ -#define USB_OTG_DOEPCTL_MPSIZ USB_OTG_DOEPCTL_MPSIZ_Msk /*!< Maximum packet size */ /*! Date: Thu, 2 Nov 2023 15:22:02 +0700 Subject: skip tuh_max3421_spi_cs_api() in hcd_init() only call tuh_max3421_spi_cs_api() in SPI start/end transfer since Arduino port use this to call begin/endTransaction() --- src/portable/analog/max3421/hcd_max3421.c | 1 - 1 file changed, 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 4665c1b06..65f87f7c6 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -417,7 +417,6 @@ bool hcd_init(uint8_t rhport) { (void) rhport; tuh_max3421_int_api(rhport, false); - tuh_max3421_spi_cs_api(rhport, false); TU_LOG2_INT(sizeof(max3421_ep_t)); TU_LOG2_INT(sizeof(max3421_data_t)); -- cgit v1.3.1 From 4b9320e40ea65ca023925d0a644b116b7066e06f Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 3 Nov 2023 22:22:13 +0700 Subject: fix race condition when dev0 is removed while enumerating --- src/host/usbh.c | 70 +++++++++++++------------- src/portable/raspberrypi/pio_usb/hcd_pio_usb.c | 16 +++--- 2 files changed, 44 insertions(+), 42 deletions(-) (limited to 'src/portable') diff --git a/src/host/usbh.c b/src/host/usbh.c index 8d75c9726..fb4fbe3cb 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -55,16 +55,12 @@ typedef struct uint8_t rhport; uint8_t hub_addr; uint8_t hub_port; - uint8_t speed; - - // enumeration is in progress, done when all interfaces are configured - volatile uint8_t enumerating; -// struct TU_ATTR_PACKED { -// uint8_t speed : 4; // packed speed to save footprint -// volatile uint8_t enumerating : 1; -// uint8_t TU_RESERVED : 3; -// }; + struct TU_ATTR_PACKED { + uint8_t speed : 4; // packed speed to save footprint + volatile uint8_t enumerating : 1; // enumeration is in progress, false if not connected or all interfaces are configured + uint8_t TU_RESERVED : 3; + }; } usbh_dev0_t; typedef struct { @@ -431,8 +427,8 @@ void tuh_task_ext(uint32_t timeout_ms, bool in_isr) { switch (event.event_id) { case HCD_EVENT_DEVICE_ATTACH: - // due to the shared _usbh_ctrl_buf, we must complete enumerating - // one device before enumerating another one. + // due to the shared _usbh_ctrl_buf, we must complete enumerating one device before enumerating another one. + // TODO better to have an separated queue for newly attached devices if ( _dev0.enumerating ) { TU_LOG_USBH("[%u:] USBH Defer Attach until current enumeration complete\r\n", event.rhport); @@ -556,11 +552,13 @@ bool tuh_control_xfer (tuh_xfer_t* xfer) { // EP0 with setup packet TU_VERIFY(xfer->ep_addr == 0 && xfer->setup); - // pre-check to help reducing mutex lock - TU_VERIFY(_ctrl_xfer.stage == CONTROL_STAGE_IDLE); - + // Check if device is still connected (enumerating for dev0) uint8_t const daddr = xfer->daddr; + if ( daddr == 0 && !_dev0.enumerating) return false; + if ( daddr != 0 && get_device(daddr)->connected == 0) return false; + // pre-check to help reducing mutex lock + TU_VERIFY(_ctrl_xfer.stage == CONTROL_STAGE_IDLE); (void) osal_mutex_lock(_usbh_mutex, OSAL_TIMEOUT_WAIT_FOREVER); bool const is_idle = (_ctrl_xfer.stage == CONTROL_STAGE_IDLE); @@ -917,19 +915,23 @@ void hcd_devtree_get_info(uint8_t dev_addr, hcd_devtree_info_t* devtree_info) } } -TU_ATTR_FAST_FUNC void hcd_event_handler(hcd_event_t const* event, bool in_isr) -{ - switch (event->event_id) - { -// case HCD_EVENT_DEVICE_REMOVE: -// // FIXME device remove from a hub need an HCD API for hcd to free up endpoint -// // mark device as removing to prevent further xfer before the event is processed in usbh task -// break; +TU_ATTR_FAST_FUNC void hcd_event_handler(hcd_event_t const* event, bool in_isr) { + switch (event->event_id) { + case HCD_EVENT_DEVICE_REMOVE: + // FIXME device remove from a hub need an HCD API for hcd to free up endpoint + // mark device as removing to prevent further xfer before the event is processed in usbh task - default: - osal_queue_send(_usbh_q, event, in_isr); - break; + // Check if dev0 is removed + if ((event->rhport == _dev0.rhport) && (event->connection.hub_addr == _dev0.hub_addr) && + (event->connection.hub_port == _dev0.hub_port)) { + _dev0.enumerating = 0; + } + break; + + default: break; } + + osal_queue_send(_usbh_q, event, in_isr); } //--------------------------------------------------------------------+ @@ -1294,8 +1296,7 @@ static bool _parse_configuration_descriptor (uint8_t dev_addr, tusb_desc_configu static void enum_full_complete(void); // process device enumeration -static void process_enumeration(tuh_xfer_t* xfer) -{ +static void process_enumeration(tuh_xfer_t* xfer) { // Retry a few times with transfers in enumeration since device can be unstable when starting up enum { ATTEMPT_COUNT_MAX = 3, @@ -1303,19 +1304,20 @@ static void process_enumeration(tuh_xfer_t* xfer) }; static uint8_t failed_count = 0; - if (XFER_RESULT_SUCCESS != xfer->result) - { + if (XFER_RESULT_SUCCESS != xfer->result) { // retry if not reaching max attempt - if ( failed_count < ATTEMPT_COUNT_MAX ) - { + bool retry = _dev0.enumerating && (failed_count < ATTEMPT_COUNT_MAX); + if ( retry ) { failed_count++; osal_task_delay(ATTEMPT_DELAY_MS); // delay a bit TU_LOG1("Enumeration attempt %u\r\n", failed_count); - TU_ASSERT(tuh_control_xfer(xfer), ); - }else - { + retry = tuh_control_xfer(xfer); + } + + if (!retry) { enum_full_complete(); } + return; } failed_count = 0; diff --git a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c index 93bc1bf43..f4de3c51d 100644 --- a/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c +++ b/src/portable/raspberrypi/pio_usb/hcd_pio_usb.c @@ -182,14 +182,6 @@ void __no_inline_not_in_flash_func(pio_usb_host_irq_handler)(uint8_t root_id) { root_port_t *rport = PIO_USB_ROOT_PORT(root_id); uint32_t const ints = rport->ints; - if ( ints & PIO_USB_INTS_CONNECT_BITS ) { - hcd_event_device_attach(tu_rhport, true); - } - - if ( ints & PIO_USB_INTS_DISCONNECT_BITS ) { - hcd_event_device_remove(tu_rhport, true); - } - if ( ints & PIO_USB_INTS_ENDPOINT_COMPLETE_BITS ) { handle_endpoint_irq(rport, XFER_RESULT_SUCCESS, &rport->ep_complete); } @@ -202,6 +194,14 @@ void __no_inline_not_in_flash_func(pio_usb_host_irq_handler)(uint8_t root_id) { handle_endpoint_irq(rport, XFER_RESULT_FAILED, &rport->ep_error); } + if ( ints & PIO_USB_INTS_CONNECT_BITS ) { + hcd_event_device_attach(tu_rhport, true); + } + + if ( ints & PIO_USB_INTS_DISCONNECT_BITS ) { + hcd_event_device_remove(tu_rhport, true); + } + // clear all rport->ints &= ~ints; } -- cgit v1.3.1 From b5b34e73d6cbce1a1d85999ef92712fb98a73a84 Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Sun, 19 Nov 2023 16:10:16 +0100 Subject: Add dwc2 info of F429. --- src/portable/synopsys/dwc2/dwc2_info.md | 108 ++++++++++++++++---------------- src/portable/synopsys/dwc2/dwc2_info.py | 2 + 2 files changed, 56 insertions(+), 54 deletions(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dwc2_info.md b/src/portable/synopsys/dwc2/dwc2_info.md index 2d8ab067f..f298f6656 100644 --- a/src/portable/synopsys/dwc2/dwc2_info.md +++ b/src/portable/synopsys/dwc2/dwc2_info.md @@ -1,54 +1,54 @@ -| | BCM2711 (Pi4) | EFM32GG FullSpeed | ESP32-S2 | STM32F407 Fullspeed | STM32F407 Highspeed | STM32F411 Fullspeed | STM32F412 Fullspeed | STM32F723 Fullspeed | STM32F723 HighSpeed | STM32F767 Fullspeed | STM32H743 Highspeed | STM32L476 Fullspeed | STM32U5A5 Highspeed | GD32VF103 Fullspeed | XMC4500 | -|:----------------------------|:----------------|:--------------------|:-----------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:-----------| -| guid | 0x2708A000 | 0x00000000 | 0x00000000 | 0x00001200 | 0x00001100 | 0x00001200 | 0x00002000 | 0x00003000 | 0x00003100 | 0x00002000 | 0x00002300 | 0x00002000 | 0x00005000 | 0x00001000 | 0x00AEC000 | -| gsnpsid | 0x4F54280A | 0x4F54330A | 0x4F54400A | 0x4F54281A | 0x4F54281A | 0x4F54281A | 0x4F54320A | 0x4F54330A | 0x4F54330A | 0x4F54320A | 0x4F54330A | 0x4F54310A | 0x4F54411A | 0x00000000 | 0x4F54292A | -| ghwcfg1 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | -| ghwcfg2 | 0x228DDD50 | 0x228F5910 | 0x224DD930 | 0x229DCD20 | 0x229ED590 | 0x229DCD20 | 0x229ED520 | 0x229ED520 | 0x229FE1D0 | 0x229ED520 | 0x229FE190 | 0x229ED520 | 0x228FE052 | 0x00000000 | 0x228F5930 | -| - op_mode | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 2 | 0 | 0 | -| - arch | 2 | 2 | 2 | 0 | 2 | 0 | 0 | 0 | 2 | 0 | 2 | 0 | 2 | 0 | 2 | -| - point2point | 0 | 0 | 1 | 1 | 0 | 1 | 1 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | 1 | -| - hs_phy_type | 1 | 0 | 0 | 0 | 2 | 0 | 0 | 0 | 3 | 0 | 2 | 0 | 1 | 0 | 0 | -| - fs_phy_type | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | -| - num_dev_ep | 7 | 6 | 6 | 3 | 5 | 3 | 5 | 5 | 8 | 5 | 8 | 5 | 8 | 0 | 6 | -| - num_host_ch | 7 | 13 | 7 | 7 | 11 | 7 | 11 | 11 | 15 | 11 | 15 | 11 | 15 | 0 | 13 | -| - period_channel_support | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | -| - enable_dynamic_fifo | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | -| - mul_cpu_int | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | -| - reserved21 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | -| - nperiod_tx_q_depth | 2 | 2 | 1 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 0 | 2 | -| - host_period_tx_q_depth | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 0 | 2 | -| - dev_token_q_depth | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 0 | 8 | -| - otg_enable_ic_usb | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | -| ghwcfg3 | 0x0FF000E8 | 0x01F204E8 | 0x00C804B5 | 0x020001E8 | 0x03F403E8 | 0x020001E8 | 0x0200D1E8 | 0x0200D1E8 | 0x03EED2E8 | 0x0200D1E8 | 0x03B8D2E8 | 0x0200D1E8 | 0x03B882E8 | 0x00000000 | 0x027A01E5 | -| - xfer_size_width | 8 | 8 | 5 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 0 | 5 | -| - packet_size_width | 6 | 6 | 3 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 0 | 6 | -| - otg_enable | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | -| - i2c_enable | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | 1 | -| - vendor_ctrl_itf | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | -| - optional_feature_removed | 0 | 1 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | -| - synch_reset | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | -| - otg_adp_support | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | -| - otg_enable_hsic | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | -| - battery_charger_support | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | -| - lpm_mode | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | -| - total_fifo_size | 4080 | 498 | 200 | 512 | 1012 | 512 | 512 | 512 | 1006 | 512 | 952 | 512 | 952 | 0 | 634 | -| ghwcfg4 | 0x1FF00020 | 0x1BF08030 | 0xD3F0A030 | 0x0FF08030 | 0x17F00030 | 0x0FF08030 | 0x17F08030 | 0x17F08030 | 0x23F00030 | 0x17F08030 | 0xE3F00030 | 0x17F08030 | 0xE2103E30 | 0x00000000 | 0xDBF08030 | -| - num_dev_period_in_ep | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | -| - power_optimized | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | -| - ahb_freq_min | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | -| - hibernation | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | -| - reserved7 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 4 | 0 | 0 | -| - service_interval_mode | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | -| - ipg_isoc_en | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | -| - acg_enable | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | -| - reserved13 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | -| - utmi_phy_data_width | 0 | 2 | 2 | 2 | 0 | 2 | 2 | 2 | 0 | 2 | 0 | 2 | 0 | 0 | 2 | -| - dev_ctrl_ep_num | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | -| - iddg_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | -| - vbus_valid_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | -| - a_valid_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | -| - b_valid_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | -| - dedicated_fifos | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | -| - num_dev_in_eps | 15 | 13 | 9 | 7 | 11 | 7 | 11 | 11 | 1 | 11 | 1 | 11 | 1 | 0 | 13 | -| - dma_desc_enable | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | -| - dma_dynamic | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | +| | BCM2711 (Pi4) | EFM32GG FullSpeed | ESP32-S2 | STM32F407 Fullspeed | STM32F407 Highspeed | STM32F411 Fullspeed | STM32F412 Fullspeed | STM32F429 Fullspeed | STM32F429 Highspeed | STM32F723 Fullspeed | STM32F723 HighSpeed | STM32F767 Fullspeed | STM32H743 Highspeed | STM32L476 Fullspeed | STM32U5A5 Highspeed | GD32VF103 Fullspeed | XMC4500 | +|:----------------------------|:----------------|:--------------------|:-----------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:-----------| +| guid | 0x2708A000 | 0x00000000 | 0x00000000 | 0x00001200 | 0x00001100 | 0x00001200 | 0x00002000 | 0x00001200 | 0x00001100 | 0x00003000 | 0x00003100 | 0x00002000 | 0x00002300 | 0x00002000 | 0x00005000 | 0x00001000 | 0x00AEC000 | +| gsnpsid | 0x4F54280A | 0x4F54330A | 0x4F54400A | 0x4F54281A | 0x4F54281A | 0x4F54281A | 0x4F54320A | 0x4F54281A | 0x4F54281A | 0x4F54330A | 0x4F54330A | 0x4F54320A | 0x4F54330A | 0x4F54310A | 0x4F54411A | 0x00000000 | 0x4F54292A | +| ghwcfg1 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | +| ghwcfg2 | 0x228DDD50 | 0x228F5910 | 0x224DD930 | 0x229DCD20 | 0x229ED590 | 0x229DCD20 | 0x229ED520 | 0x229DCD20 | 0x229ED590 | 0x229ED520 | 0x229FE1D0 | 0x229ED520 | 0x229FE190 | 0x229ED520 | 0x228FE052 | 0x00000000 | 0x228F5930 | +| - op_mode | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 2 | 0 | 0 | +| - arch | 2 | 2 | 2 | 0 | 2 | 0 | 0 | 0 | 2 | 0 | 2 | 0 | 2 | 0 | 2 | 0 | 2 | +| - point2point | 0 | 0 | 1 | 1 | 0 | 1 | 1 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | 1 | +| - hs_phy_type | 1 | 0 | 0 | 0 | 2 | 0 | 0 | 0 | 2 | 0 | 3 | 0 | 2 | 0 | 1 | 0 | 0 | +| - fs_phy_type | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - num_dev_ep | 7 | 6 | 6 | 3 | 5 | 3 | 5 | 3 | 5 | 5 | 8 | 5 | 8 | 5 | 8 | 0 | 6 | +| - num_host_ch | 7 | 13 | 7 | 7 | 11 | 7 | 11 | 7 | 11 | 11 | 15 | 11 | 15 | 11 | 15 | 0 | 13 | +| - period_channel_support | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - enable_dynamic_fifo | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - mul_cpu_int | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | +| - reserved21 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - nperiod_tx_q_depth | 2 | 2 | 1 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 0 | 2 | +| - host_period_tx_q_depth | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 2 | 0 | 2 | +| - dev_token_q_depth | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 0 | 8 | +| - otg_enable_ic_usb | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| ghwcfg3 | 0x0FF000E8 | 0x01F204E8 | 0x00C804B5 | 0x020001E8 | 0x03F403E8 | 0x020001E8 | 0x0200D1E8 | 0x020001E8 | 0x03F403E8 | 0x0200D1E8 | 0x03EED2E8 | 0x0200D1E8 | 0x03B8D2E8 | 0x0200D1E8 | 0x03B882E8 | 0x00000000 | 0x027A01E5 | +| - xfer_size_width | 8 | 8 | 5 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 8 | 0 | 5 | +| - packet_size_width | 6 | 6 | 3 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 6 | 0 | 6 | +| - otg_enable | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - i2c_enable | 0 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | 1 | +| - vendor_ctrl_itf | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | +| - optional_feature_removed | 0 | 1 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - synch_reset | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - otg_adp_support | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | +| - otg_enable_hsic | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - battery_charger_support | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 0 | +| - lpm_mode | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | +| - total_fifo_size | 4080 | 498 | 200 | 512 | 1012 | 512 | 512 | 512 | 1012 | 512 | 1006 | 512 | 952 | 512 | 952 | 0 | 634 | +| ghwcfg4 | 0x1FF00020 | 0x1BF08030 | 0xD3F0A030 | 0x0FF08030 | 0x17F00030 | 0x0FF08030 | 0x17F08030 | 0x0FF08030 | 0x17F00030 | 0x17F08030 | 0x23F00030 | 0x17F08030 | 0xE3F00030 | 0x17F08030 | 0xE2103E30 | 0x00000000 | 0xDBF08030 | +| - num_dev_period_in_ep | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - power_optimized | 0 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - ahb_freq_min | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - hibernation | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - reserved7 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 4 | 0 | 0 | +| - service_interval_mode | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | +| - ipg_isoc_en | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | +| - acg_enable | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | +| - reserved13 | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 0 | +| - utmi_phy_data_width | 0 | 2 | 2 | 2 | 0 | 2 | 2 | 2 | 0 | 2 | 0 | 2 | 0 | 2 | 0 | 0 | 2 | +| - dev_ctrl_ep_num | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | +| - iddg_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 1 | +| - vbus_valid_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - a_valid_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - b_valid_filter_enabled | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - dedicated_fifos | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | +| - num_dev_in_eps | 15 | 13 | 9 | 7 | 11 | 7 | 11 | 7 | 11 | 11 | 1 | 11 | 1 | 11 | 1 | 0 | 13 | +| - dma_desc_enable | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | +| - dma_dynamic | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | \ No newline at end of file diff --git a/src/portable/synopsys/dwc2/dwc2_info.py b/src/portable/synopsys/dwc2/dwc2_info.py index 0af6c4c77..4bcdb4fe5 100644 --- a/src/portable/synopsys/dwc2/dwc2_info.py +++ b/src/portable/synopsys/dwc2/dwc2_info.py @@ -12,6 +12,8 @@ dwc2_reg_value = { 'STM32F407 Highspeed': [0x1100, 0x4F54281A, 0, 0x229ED590, 0x3F403E8, 0x17F00030], 'STM32F411 Fullspeed': [0x1200, 0x4F54281A, 0, 0x229DCD20, 0x20001E8, 0xFF08030], 'STM32F412 Fullspeed': [0x2000, 0x4F54320A, 0, 0x229ED520, 0x200D1E8, 0x17F08030], + 'STM32F429 Fullspeed': [0x1200, 0x4F54281A, 0, 0x229DCD20, 0x20001E8, 0xFF08030], + 'STM32F429 Highspeed': [0x1100, 0x4F54281A, 0, 0x229ED590, 0x3F403E8, 0x17F00030], 'STM32F723 Fullspeed': [0x3000, 0x4F54330A, 0, 0x229ED520, 0x200D1E8, 0x17F08030], 'STM32F723 HighSpeed': [0x3100, 0x4F54330A, 0, 0x229FE1D0, 0x3EED2E8, 0x23F00030], 'STM32F767 Fullspeed': [0x2000, 0x4F54320A, 0, 0x229ED520, 0x200D1E8, 0x17F08030], -- cgit v1.3.1 From 8af470e06d032d1b9731d817741318883c0b8fa0 Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Sun, 19 Nov 2023 16:19:11 +0100 Subject: Fix CI --- src/portable/synopsys/dwc2/dwc2_info.md | 2 +- src/portable/synopsys/dwc2/dwc2_info.py | 1 + 2 files changed, 2 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dwc2_info.md b/src/portable/synopsys/dwc2/dwc2_info.md index f298f6656..d093502b0 100644 --- a/src/portable/synopsys/dwc2/dwc2_info.md +++ b/src/portable/synopsys/dwc2/dwc2_info.md @@ -51,4 +51,4 @@ | - dedicated_fifos | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 1 | 0 | 0 | 1 | | - num_dev_in_eps | 15 | 13 | 9 | 7 | 11 | 7 | 11 | 7 | 11 | 11 | 1 | 11 | 1 | 11 | 1 | 0 | 13 | | - dma_desc_enable | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 0 | -| - dma_dynamic | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | \ No newline at end of file +| - dma_dynamic | 0 | 0 | 1 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 1 | 0 | 1 | 0 | 1 | diff --git a/src/portable/synopsys/dwc2/dwc2_info.py b/src/portable/synopsys/dwc2/dwc2_info.py index 4bcdb4fe5..03c095655 100644 --- a/src/portable/synopsys/dwc2/dwc2_info.py +++ b/src/portable/synopsys/dwc2/dwc2_info.py @@ -154,6 +154,7 @@ def render_md(): # Write the Markdown table to a file with open('dwc2_info.md', 'w') as md_file: md_file.write(df.to_markdown()) + md_file.write('\n') if __name__ == '__main__': -- cgit v1.3.1 From 1f71625a32a77d5fe243f71f9e8be03c9bbc41d1 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 20 Nov 2023 21:31:06 +0700 Subject: add tuh_max3421_reg_read(), tuh_max3421_reg_read() for application usage added max3241 for feather m4 and tested --- hw/bsp/samd51/boards/feather_m4_express/board.h | 17 ++++++ hw/bsp/samd51/family.c | 28 +++++++-- src/portable/analog/max3421/hcd_max3421.c | 78 +++++++++++++++---------- 3 files changed, 86 insertions(+), 37 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/samd51/boards/feather_m4_express/board.h b/hw/bsp/samd51/boards/feather_m4_express/board.h index 4629643fd..474163c06 100644 --- a/hw/bsp/samd51/boards/feather_m4_express/board.h +++ b/hw/bsp/samd51/boards/feather_m4_express/board.h @@ -31,6 +31,8 @@ extern "C" { #endif +#define _PINNUM(port, pin) ((port)*32 + (pin)) + // LED #define LED_PIN 23 #define LED_STATE_ON 1 @@ -43,6 +45,21 @@ #define UART_TX_PIN (32 + 17) #define UART_RX_PIN (32 + 16) +// SPI for USB host shield +#define MAX3421_SERCOM_ID 1 // SERCOM2 +#define MAX3421_SERCOM_FUNCTION 2 // function C + +#define MAX3421_SCK_PIN _PINNUM(0, 17) +#define MAX3421_MOSI_PIN _PINNUM(1, 23) +#define MAX3421_MISO_PIN _PINNUM(1, 22) +#define MAX3421_TX_PAD 2 // MOSI = PAD_3, SCK = PAD_1 +#define MAX3421_RX_PAD 2 // MISO = PAD_2 + +#define MAX3421_CS_PIN 21 // D11 + +#define MAX3421_INTR_PIN 20 // D10 +#define MAX3421_INTR_EIC_ID 4 // EIC4 + #ifdef __cplusplus } #endif diff --git a/hw/bsp/samd51/family.c b/hw/bsp/samd51/family.c index bca18e1a2..2a2aee982 100644 --- a/hw/bsp/samd51/family.c +++ b/hw/bsp/samd51/family.c @@ -76,12 +76,18 @@ void USB_3_Handler(void) { // Implementation //--------------------------------------------------------------------+ -#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 +#if CFG_TUH_ENABLED && CFG_TUH_MAX3421 + +// API to read MAX3421's register. Implemented by TinyUSB +extern uint8_t tuh_max3421_reg_read(uint8_t rhport, uint8_t reg, bool in_isr); + +// API to write MAX3421's register. Implemented by TinyUSB +extern bool tuh_max3421_reg_write(uint8_t rhport, uint8_t reg, uint8_t data, bool in_isr); + #define MAX3421_SERCOM TU_XSTRCAT(SERCOM, MAX3421_SERCOM_ID) #define MAX3421_EIC_Handler TU_XSTRCAT3(EIC_, MAX3421_INTR_EIC_ID, _Handler) static void max3421_init(void); - #endif void board_init(void) { @@ -136,11 +142,23 @@ void board_init(void) { gpio_set_pin_function(PIN_PA24, PINMUX_PA24H_USB_DM); gpio_set_pin_function(PIN_PA25, PINMUX_PA25H_USB_DP); -#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 +#if CFG_TUH_ENABLED && CFG_TUH_MAX3421 max3421_init(); #endif } +void board_init_after_tusb(void) { +#if CFG_TUH_ENABLED && CFG_TUH_MAX3421 + // FeatherWing MAX3421E use MAX3421E's GPIO0 for VBUS enable + enum { + IOPINS1_ADDR = 20u << 3, // 0xA0 + }; + + uint8_t rhport = 1; + tuh_max3421_reg_write(rhport, IOPINS1_ADDR, 0x01, false); +#endif +} + //--------------------------------------------------------------------+ // Board porting API //--------------------------------------------------------------------+ @@ -182,7 +200,7 @@ uint32_t board_millis(void) { //--------------------------------------------------------------------+ // API: SPI transfer with MAX3421E, must be implemented by application //--------------------------------------------------------------------+ -#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 +#if CFG_TUH_ENABLED && CFG_TUH_MAX3421 static void max3421_init(void) { //------------- SPI Init -------------// @@ -262,7 +280,7 @@ static void max3421_init(void) { // Enable the SPI module sercom->SPI.CTRLA.bit.ENABLE = 1; - while (sercom->SPI.SYNCBUSY.bit.ENABLE); + while (sercom->SPI.SYNCBUSY.bit.ENABLE) {} //------------- External Interrupt -------------// diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 65f87f7c6..2abd74d51 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -54,6 +54,12 @@ enum { CPUCTL_ADDR = 16u << 3, // 0x80 PINCTL_ADDR = 17u << 3, // 0x88 REVISION_ADDR = 18u << 3, // 0x90 + // 19 is not used + IOPINS1_ADDR = 20u << 3, // 0xA0 + IOPINS2_ADDR = 21u << 3, // 0xA8 + GPINIRQ_ADDR = 22u << 3, // 0xB0 + GPINIEN_ADDR = 23u << 3, // 0xB8 + GPINPOL_ADDR = 24u << 3, // 0xC0 HIRQ_ADDR = 25u << 3, // 0xC8 HIEN_ADDR = 26u << 3, // 0xD0 MODE_ADDR = 27u << 3, // 0xD8 @@ -207,7 +213,9 @@ typedef struct { static max3421_data_t _hcd_data; //--------------------------------------------------------------------+ -// API: SPI transfer with MAX3421E, must be implemented by application +// API: SPI transfer with MAX3421E +// - spi_cs_api(), spi_xfer_api(), int_api(): must be implemented by application +// - reg_read(), reg_write(): is implemented by this driver, can be used by application //--------------------------------------------------------------------+ // API to control MAX3421 SPI CS @@ -220,11 +228,18 @@ extern bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const* tx_buf, uint // API to enable/disable MAX3421 INTR pin interrupt extern void tuh_max3421_int_api(uint8_t rhport, bool enabled); +// API to read MAX3421's register. Implemented by TinyUSB +uint8_t tuh_max3421_reg_read(uint8_t rhport, uint8_t reg, bool in_isr); + +// API to write MAX3421's register. Implemented by TinyUSB +bool tuh_max3421_reg_write(uint8_t rhport, uint8_t reg, uint8_t data, bool in_isr); + //--------------------------------------------------------------------+ -// SPI Helper +// SPI Commands and Helper //--------------------------------------------------------------------+ -static void handle_connect_irq(uint8_t rhport, bool in_isr); -static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr); + +#define reg_read tuh_max3421_reg_read +#define reg_write tuh_max3421_reg_write static void max3421_spi_lock(uint8_t rhport, bool in_isr) { // disable interrupt and mutex lock (for pre-emptive RTOS) if not in_isr @@ -248,61 +263,60 @@ static void max3421_spi_unlock(uint8_t rhport, bool in_isr) { } } -static void fifo_write(uint8_t rhport, uint8_t reg, uint8_t const * buffer, uint16_t len, bool in_isr) { - uint8_t hirq; - reg |= CMDBYTE_WRITE; +uint8_t tuh_max3421_reg_read(uint8_t rhport, uint8_t reg, bool in_isr) { + uint8_t tx_buf[2] = {reg, 0}; + uint8_t rx_buf[2] = {0, 0}; max3421_spi_lock(rhport, in_isr); - - tuh_max3421_spi_xfer_api(rhport, ®, &hirq, 1); - _hcd_data.hirq = hirq; - tuh_max3421_spi_xfer_api(rhport, buffer, NULL, len); - + bool ret = tuh_max3421_spi_xfer_api(rhport, tx_buf, rx_buf, 2); max3421_spi_unlock(rhport, in_isr); + _hcd_data.hirq = rx_buf[0]; + return ret ? rx_buf[1] : 0; } -static void fifo_read(uint8_t rhport, uint8_t * buffer, uint16_t len, bool in_isr) { - uint8_t hirq; - uint8_t const reg = RCVVFIFO_ADDR; +bool tuh_max3421_reg_write(uint8_t rhport, uint8_t reg, uint8_t data, bool in_isr) { + uint8_t tx_buf[2] = {reg | CMDBYTE_WRITE, data}; + uint8_t rx_buf[2] = {0, 0}; max3421_spi_lock(rhport, in_isr); + bool ret = tuh_max3421_spi_xfer_api(rhport, tx_buf, rx_buf, 2); + max3421_spi_unlock(rhport, in_isr); - tuh_max3421_spi_xfer_api(rhport, ®, &hirq, 1); - _hcd_data.hirq = hirq; - tuh_max3421_spi_xfer_api(rhport, NULL, buffer, len); + // HIRQ register since we are in full-duplex mode + _hcd_data.hirq = rx_buf[0]; - max3421_spi_unlock(rhport, in_isr); + return ret; } -static void reg_write(uint8_t rhport, uint8_t reg, uint8_t data, bool in_isr) { - uint8_t tx_buf[2] = {reg | CMDBYTE_WRITE, data}; - uint8_t rx_buf[2] = {0, 0}; +static void fifo_write(uint8_t rhport, uint8_t reg, uint8_t const * buffer, uint16_t len, bool in_isr) { + uint8_t hirq; + reg |= CMDBYTE_WRITE; max3421_spi_lock(rhport, in_isr); - tuh_max3421_spi_xfer_api(rhport, tx_buf, rx_buf, 2); + tuh_max3421_spi_xfer_api(rhport, ®, &hirq, 1); + _hcd_data.hirq = hirq; + tuh_max3421_spi_xfer_api(rhport, buffer, NULL, len); max3421_spi_unlock(rhport, in_isr); - // HIRQ register since we are in full-duplex mode - _hcd_data.hirq = rx_buf[0]; } -static uint8_t reg_read(uint8_t rhport, uint8_t reg, bool in_isr) { - uint8_t tx_buf[2] = {reg, 0}; - uint8_t rx_buf[2] = {0, 0}; +static void fifo_read(uint8_t rhport, uint8_t * buffer, uint16_t len, bool in_isr) { + uint8_t hirq; + uint8_t const reg = RCVVFIFO_ADDR; max3421_spi_lock(rhport, in_isr); - bool ret = tuh_max3421_spi_xfer_api(rhport, tx_buf, rx_buf, 2); + tuh_max3421_spi_xfer_api(rhport, ®, &hirq, 1); + _hcd_data.hirq = hirq; + tuh_max3421_spi_xfer_api(rhport, NULL, buffer, len); max3421_spi_unlock(rhport, in_isr); - - _hcd_data.hirq = rx_buf[0]; - return ret ? rx_buf[1] : 0; } +//------------- register write helper -------------// static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr) { reg_write(rhport, HIRQ_ADDR, data, in_isr); // HIRQ write 1 is clear -- cgit v1.3.1 From 025ffa200c5508c23e76316045792af4f7728da5 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 22 Nov 2023 17:36:52 +0700 Subject: add spec version to dwc2 info --- src/portable/synopsys/dwc2/dwc2_info.md | 1 + src/portable/synopsys/dwc2/dwc2_info.py | 14 +- src/portable/synopsys/dwc2/hwcfg_list.md | 777 ------------------------------- 3 files changed, 12 insertions(+), 780 deletions(-) delete mode 100644 src/portable/synopsys/dwc2/hwcfg_list.md (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dwc2_info.md b/src/portable/synopsys/dwc2/dwc2_info.md index d093502b0..8690a0755 100644 --- a/src/portable/synopsys/dwc2/dwc2_info.md +++ b/src/portable/synopsys/dwc2/dwc2_info.md @@ -2,6 +2,7 @@ |:----------------------------|:----------------|:--------------------|:-----------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:----------------------|:-----------| | guid | 0x2708A000 | 0x00000000 | 0x00000000 | 0x00001200 | 0x00001100 | 0x00001200 | 0x00002000 | 0x00001200 | 0x00001100 | 0x00003000 | 0x00003100 | 0x00002000 | 0x00002300 | 0x00002000 | 0x00005000 | 0x00001000 | 0x00AEC000 | | gsnpsid | 0x4F54280A | 0x4F54330A | 0x4F54400A | 0x4F54281A | 0x4F54281A | 0x4F54281A | 0x4F54320A | 0x4F54281A | 0x4F54281A | 0x4F54330A | 0x4F54330A | 0x4F54320A | 0x4F54330A | 0x4F54310A | 0x4F54411A | 0x00000000 | 0x4F54292A | +| - specs version | 2.80a | 3.30a | 4.00a | 2.81a | 2.81a | 2.81a | 3.20a | 2.81a | 2.81a | 3.30a | 3.30a | 3.20a | 3.30a | 3.10a | 4.11a | 0.00W | 2.92a | | ghwcfg1 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | 0x00000000 | | ghwcfg2 | 0x228DDD50 | 0x228F5910 | 0x224DD930 | 0x229DCD20 | 0x229ED590 | 0x229DCD20 | 0x229ED520 | 0x229DCD20 | 0x229ED590 | 0x229ED520 | 0x229FE1D0 | 0x229ED520 | 0x229FE190 | 0x229ED520 | 0x228FE052 | 0x00000000 | 0x228F5930 | | - op_mode | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 0 | 2 | 0 | 0 | diff --git a/src/portable/synopsys/dwc2/dwc2_info.py b/src/portable/synopsys/dwc2/dwc2_info.py index 03c095655..55bec3d23 100644 --- a/src/portable/synopsys/dwc2/dwc2_info.py +++ b/src/portable/synopsys/dwc2/dwc2_info.py @@ -36,6 +36,7 @@ dwc2_reg_value = { # }, dwc2_info = {key: {field: value for field, value in zip(dwc2_reg_list, values)} for key, values in dwc2_reg_value.items()} + class GHWCFG2(ctypes.LittleEndianStructure): _fields_ = [ ("op_mode", ctypes.c_uint32, 3), @@ -130,13 +131,20 @@ def render_md(): # Create an empty list to hold the dictionaries dwc2_info_list = [] - #Iterate over the dwc2_info dictionary and extract fields + # Iterate over the dwc2_info dictionary and extract fields for device, reg_values in dwc2_info.items(): entry_dict = {"Device": device} for r_name, r_value in reg_values.items(): entry_dict[r_name] = f"0x{r_value:08X}" - # Print bit-field values - if r_name.upper() in globals(): + + if r_name == 'gsnpsid': + # Get dwc2 specs version + major = ((r_value >> 8) >> 4) & 0x0F + minor = (r_value >> 4) & 0xFF + patch = chr((r_value & 0x0F) + ord('a') - 0xA) + entry_dict[f' - specs version'] = f"{major:X}.{minor:02X}{patch}" + elif r_name.upper() in globals(): + # Get bit-field values which exist as ctypes structures class_name = globals()[r_name.upper()] ghwcfg = class_name.from_buffer_copy(r_value.to_bytes(4, byteorder='little')) for field_name, field_type, _ in class_name._fields_: diff --git a/src/portable/synopsys/dwc2/hwcfg_list.md b/src/portable/synopsys/dwc2/hwcfg_list.md deleted file mode 100644 index b5590da00..000000000 --- a/src/portable/synopsys/dwc2/hwcfg_list.md +++ /dev/null @@ -1,777 +0,0 @@ -# DWC2 Hardware Configuration Registers - -## Broadcom BCM2711 (Pi4) - -dwc2->guid = 2708A000 -dwc2->gsnpsid = 4F54280A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 228DDD50 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 2 -hw_cfg2->point2point = 0 -hw_cfg2->hs_phy_type = 1 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 7 -hw_cfg2->num_host_ch = 7 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 0 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = FF000E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 0 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 0 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 0 -hw_cfg3->lpm_mode = 0 -hw_cfg3->total_fifo_size = 4080 - -dwc2->ghwcfg4 = 1FF00020 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 0 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 0 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 15 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -## EFM32GG FS - -dwc2->guid = 0 -dwc2->gsnpsid = 4F54330A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 228F5910 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 2 -hw_cfg2->point2point = 0 -hw_cfg2->hs_phy_type = 0 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 6 -hw_cfg2->num_host_ch = 13 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 0 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 1F204E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 0 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 1 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 0 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 0 -hw_cfg3->lpm_mode = 0 -hw_cfg3->total_fifo_size = 498 - -dwc2->ghwcfg4 = 1BF08030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 2 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 13 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -## ESP32-S2 Fullspeed - -dwc2->guid = 0 -dwc2->gsnpsid = 4F54400A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 224DD930 -hw_cfg2->op_mode = 2 -hw_cfg2->arch = 3 -hw_cfg2->point2point = 0 -hw_cfg2->hs_phy_type = 1 -hw_cfg2->fs_phy_type = 2 -hw_cfg2->num_dev_ep = 6 -hw_cfg2->num_host_ch = 9 -hw_cfg2->period_channel_support = 0 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 1 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 22 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = C804B5 -hw_cfg3->xfer_size_width = 10 -hw_cfg3->packet_size_width = 5 -hw_cfg3->otg_enable = 0 -hw_cfg3->i2c_enable = 0 -hw_cfg3->vendor_ctrl_itf = 1 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 1 -hw_cfg3->otg_adp_support = 1 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 1 -hw_cfg3->lpm_mode = 0 -hw_cfg3->total_fifo_size = 23130 - -dwc2->ghwcfg4 = D3F0A030 -hw_cfg4->num_dev_period_in_ep = 10 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 0 -hw_cfg4->hibernation = 1 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 1 -hw_cfg4->acg_enable = 1 -hw_cfg4->utmi_phy_data_width = 1 -hw_cfg4->dev_ctrl_ep_num = 10 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 0 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 0 -hw_cfg4->dedicated_fifos = 0 -hw_cfg4->num_dev_in_eps = 13 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 1 - -## STM32F407 and STM32F207 - -STM32F407 and STM32F207 are exactly the same - -### STM32F407 Fullspeed - -dwc2->guid = 1200 -dwc2->gsnpsid = 4F54281A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 229DCD20 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 0 -hw_cfg2->point2point = 1 -hw_cfg2->hs_phy_type = 0 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 3 -hw_cfg2->num_host_ch = 7 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 20001E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 1 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 0 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 0 -hw_cfg3->lpm_mode = 0 -hw_cfg3->total_fifo_size = 512 - -dwc2->ghwcfg4 = FF08030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 2 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 7 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -### STM32F407 Highspeed - -dwc2->guid = 1100 -dwc2->gsnpsid = 4F54281A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 229ED590 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 2 -hw_cfg2->point2point = 0 -hw_cfg2->hs_phy_type = 2 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 5 -hw_cfg2->num_host_ch = 11 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 3F403E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 1 -hw_cfg3->vendor_ctrl_itf = 1 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 0 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 0 -hw_cfg3->lpm_mode = 0 -hw_cfg3->total_fifo_size = 1012 - -dwc2->ghwcfg4 = 17F00030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 0 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 11 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -## STM32F411 Fullspeed - -dwc2->guid = 1200 -dwc2->gsnpsid = 4F54281A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 229DCD20 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 0 -hw_cfg2->point2point = 1 -hw_cfg2->hs_phy_type = 0 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 3 -hw_cfg2->num_host_ch = 7 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 20001E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 1 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 0 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 0 -hw_cfg3->lpm_mode = 0 -hw_cfg3->total_fifo_size = 512 - -dwc2->ghwcfg4 = FF08030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 2 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 7 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -## STM32F412 FS - -dwc2->guid = 2000 -dwc2->gsnpsid = 4F54320A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 229ED520 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 0 -hw_cfg2->point2point = 1 -hw_cfg2->hs_phy_type = 0 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 5 -hw_cfg2->num_host_ch = 11 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 200D1E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 1 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 1 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 1 -hw_cfg3->lpm_mode = 1 -hw_cfg3->total_fifo_size = 512 - -dwc2->ghwcfg4 = 17F08030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 2 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 11 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -## STM32F723 - -### STM32F723 HighSpeed - -dwc2->guid = 3100 -dwc2->gsnpsid = 4F54330A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 229FE1D0 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 2 -hw_cfg2->point2point = 0 -hw_cfg2->hs_phy_type = 3 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 8 -hw_cfg2->num_host_ch = 15 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 3EED2E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 0 -hw_cfg3->vendor_ctrl_itf = 1 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 1 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 1 -hw_cfg3->lpm_mode = 1 -hw_cfg3->total_fifo_size = 1006 - -dwc2->ghwcfg4 = 23F00030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 0 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 1 -hw_cfg4->dma_desc_enable = 1 -hw_cfg4->dma_dynamic = 0 - -### STM32F723 Fullspeed - -dwc2->guid = 3000 -dwc2->gsnpsid = 4F54330A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 229ED520 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 0 -hw_cfg2->point2point = 1 -hw_cfg2->hs_phy_type = 0 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 5 -hw_cfg2->num_host_ch = 11 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 200D1E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 1 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 1 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 1 -hw_cfg3->lpm_mode = 1 -hw_cfg3->total_fifo_size = 512 - -dwc2->ghwcfg4 = 17F08030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 2 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 11 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -## STM32F767 FS - -dwc2->guid = 2000 -dwc2->gsnpsid = 4F54320A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 229ED520 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 0 -hw_cfg2->point2point = 1 -hw_cfg2->hs_phy_type = 0 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 5 -hw_cfg2->num_host_ch = 11 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 200D1E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 1 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 1 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 1 -hw_cfg3->lpm_mode = 1 -hw_cfg3->total_fifo_size = 512 - -dwc2->ghwcfg4 = 17F08030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 2 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 11 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -## STM32H743 (both cores HS) - -dwc2->guid = 2300 -dwc2->gsnpsid = 4F54330A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 229FE190 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 2 -hw_cfg2->point2point = 0 -hw_cfg2->hs_phy_type = 2 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 8 -hw_cfg2->num_host_ch = 15 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 3B8D2E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 0 -hw_cfg3->vendor_ctrl_itf = 1 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 1 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 1 -hw_cfg3->lpm_mode = 1 -hw_cfg3->total_fifo_size = 952 - -dwc2->ghwcfg4 = E3F00030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 0 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 1 -hw_cfg4->dma_desc_enable = 1 -hw_cfg4->dma_dynamic = 1 - -## STM32L476 FS - -dwc2->guid = 2000 -dwc2->gsnpsid = 4F54310A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 229ED520 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 0 -hw_cfg2->point2point = 1 -hw_cfg2->hs_phy_type = 0 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 5 -hw_cfg2->num_host_ch = 11 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 1 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 200D1E8 -hw_cfg3->xfer_size_width = 8 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 1 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 1 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 1 -hw_cfg3->lpm_mode = 1 -hw_cfg3->total_fifo_size = 512 - -dwc2->ghwcfg4 = 17F08030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 2 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 11 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -## GD32VF103 Fullspeed - -dwc2->guid = 1000 -dwc2->gsnpsid = 0 -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 0 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 0 -hw_cfg2->point2point = 0 -hw_cfg2->hs_phy_type = 0 -hw_cfg2->fs_phy_type = 0 -hw_cfg2->num_dev_ep = 0 -hw_cfg2->num_host_ch = 0 -hw_cfg2->period_channel_support = 0 -hw_cfg2->enable_dynamic_fifo = 0 -hw_cfg2->mul_cpu_int = 0 -hw_cfg2->nperiod_tx_q_depth = 0 -hw_cfg2->host_period_tx_q_depth = 0 -hw_cfg2->dev_token_q_depth = 0 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 0 -hw_cfg3->xfer_size_width = 0 -hw_cfg3->packet_size_width = 0 -hw_cfg3->otg_enable = 0 -hw_cfg3->i2c_enable = 0 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 0 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 0 -hw_cfg3->lpm_mode = 0 -hw_cfg3->total_fifo_size = 0 - -dwc2->ghwcfg4 = 0 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 0 -hw_cfg4->ahb_freq_min = 0 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 0 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 0 -hw_cfg4->vbus_valid_filter_enabled = 0 -hw_cfg4->a_valid_filter_enabled = 0 -hw_cfg4->b_valid_filter_enabled = 0 -hw_cfg4->dedicated_fifos = 0 -hw_cfg4->num_dev_in_eps = 0 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 0 - -## XMC4500 - -dwc2->guid = AEC000 -dwc2->gsnpsid = 4F54292A -dwc2->ghwcfg1 = 0 - -dwc2->ghwcfg2 = 228F5930 -hw_cfg2->op_mode = 0 -hw_cfg2->arch = 2 -hw_cfg2->point2point = 1 -hw_cfg2->hs_phy_type = 0 -hw_cfg2->fs_phy_type = 1 -hw_cfg2->num_dev_ep = 6 -hw_cfg2->num_host_ch = 13 -hw_cfg2->period_channel_support = 1 -hw_cfg2->enable_dynamic_fifo = 1 -hw_cfg2->mul_cpu_int = 0 -hw_cfg2->nperiod_tx_q_depth = 2 -hw_cfg2->host_period_tx_q_depth = 2 -hw_cfg2->dev_token_q_depth = 8 -hw_cfg2->otg_enable_ic_usb = 0 - -dwc2->ghwcfg3 = 27A01E5 -hw_cfg3->xfer_size_width = 5 -hw_cfg3->packet_size_width = 6 -hw_cfg3->otg_enable = 1 -hw_cfg3->i2c_enable = 1 -hw_cfg3->vendor_ctrl_itf = 0 -hw_cfg3->optional_feature_removed = 0 -hw_cfg3->synch_reset = 0 -hw_cfg3->otg_adp_support = 0 -hw_cfg3->otg_enable_hsic = 0 -hw_cfg3->battery_charger_support = 0 -hw_cfg3->lpm_mode = 0 -hw_cfg3->total_fifo_size = 634 - -dwc2->ghwcfg4 = DBF08030 -hw_cfg4->num_dev_period_in_ep = 0 -hw_cfg4->power_optimized = 1 -hw_cfg4->ahb_freq_min = 1 -hw_cfg4->hibernation = 0 -hw_cfg4->service_interval_mode = 0 -hw_cfg4->ipg_isoc_en = 0 -hw_cfg4->acg_enable = 0 -hw_cfg4->utmi_phy_data_width = 2 -hw_cfg4->dev_ctrl_ep_num = 0 -hw_cfg4->iddg_filter_enabled = 1 -hw_cfg4->vbus_valid_filter_enabled = 1 -hw_cfg4->a_valid_filter_enabled = 1 -hw_cfg4->b_valid_filter_enabled = 1 -hw_cfg4->dedicated_fifos = 1 -hw_cfg4->num_dev_in_eps = 13 -hw_cfg4->dma_desc_enable = 0 -hw_cfg4->dma_dynamic = 1 -- cgit v1.3.1 From 01f22a9e25c9581c1a38559737a7ca7d1fc22c15 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 22 Nov 2023 22:50:10 +0700 Subject: fix h7 running on fullspeed phy has issue with WFI if not disable ULPI clock --- src/portable/synopsys/dwc2/dwc2_stm32.h | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dwc2_stm32.h b/src/portable/synopsys/dwc2/dwc2_stm32.h index 2070c3943..dd78ccd06 100644 --- a/src/portable/synopsys/dwc2/dwc2_stm32.h +++ b/src/portable/synopsys/dwc2/dwc2_stm32.h @@ -145,6 +145,22 @@ static inline void dwc2_phy_init(dwc2_regs_t* dwc2, uint8_t hs_phy_type) { if (hs_phy_type == HS_PHY_TYPE_NONE) { // Enable on-chip FS PHY dwc2->stm32_gccfg |= STM32_GCCFG_PWRDWN; + + // https://community.st.com/t5/stm32cubemx-mcus/why-stm32h743-usb-fs-doesn-t-work-if-freertos-tickless-idle/m-p/349480#M18867 + // H7 running on full-speed phy need to disable ULPI clock in sleep mode. + // Otherwise, USB won't work when mcu executing WFI/WFE instruction i.e tick-less RTOS. + // Note: there may be other family that is affected by this, but only H7 is tested so far + #if defined(USB_OTG_FS_PERIPH_BASE) && defined(RCC_AHB1LPENR_USB2OTGFSULPILPEN) + if ( USB_OTG_FS_PERIPH_BASE == (uint32_t) dwc2 ) { + RCC->AHB1LPENR &= ~RCC_AHB1LPENR_USB2OTGFSULPILPEN; + } + #endif + + #if defined(USB_OTG_HS_PERIPH_BASE) && defined(RCC_AHB1LPENR_USB1OTGHSULPILPEN) + if ( USB_OTG_HS_PERIPH_BASE == (uint32_t) dwc2 ) { + RCC->AHB1LPENR &= ~RCC_AHB1LPENR_USB1OTGHSULPILPEN; + } + #endif } else { #if CFG_TUSB_MCU != OPT_MCU_STM32U5 // Disable FS PHY, TODO on U5A5 (dwc2 4.11a) 16th bit is 'Host CDP behavior enable' -- cgit v1.3.1 From 7e1fe2ff83e1089a1e75e4fdc03af4b0aa6048ea Mon Sep 17 00:00:00 2001 From: IngHK Date: Fri, 24 Nov 2023 22:02:58 +0100 Subject: made log line end consistent \r\n --- examples/device/cdc_uac2/src/main.c | 2 +- src/portable/analog/max3421/hcd_max3421.c | 8 ++++---- src/portable/ehci/ehci.c | 4 ++-- src/portable/mentor/musb/dcd_musb.c | 4 ++-- 4 files changed, 9 insertions(+), 9 deletions(-) (limited to 'src/portable') diff --git a/examples/device/cdc_uac2/src/main.c b/examples/device/cdc_uac2/src/main.c index 7afa96c1a..25b2cd9a5 100644 --- a/examples/device/cdc_uac2/src/main.c +++ b/examples/device/cdc_uac2/src/main.c @@ -60,7 +60,7 @@ int main(void) led_blinking_task(); #if (CFG_TUSB_MCU == OPT_MCU_RP2040) - // printf("Hello, world!\n"); + // printf("Hello, world!\r\n"); #endif } diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 65f87f7c6..d7ce5a92f 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -382,7 +382,7 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; if (ep->xfer_pending && ep->packet_size) { -// TU_LOG3("next pending i = %u\n", i); +// TU_LOG3("next pending i = %u\r\n", i); return ep; } } @@ -391,7 +391,7 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { for (size_t i = 0; i <= idx; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; if (ep->xfer_pending && ep->packet_size) { -// TU_LOG3("next pending i = %u\n", i); +// TU_LOG3("next pending i = %u\r\n", i); return ep; } } @@ -712,9 +712,9 @@ static void handle_connect_irq(uint8_t rhport, bool in_isr) { // However, since we are always in full speed mode, we can just check J-state if (jk == HRSL_KSTATUS) { new_mode |= MODE_LOWSPEED; - TU_LOG3("Low speed\n"); + TU_LOG3("Low speed\r\n"); }else { - TU_LOG3("Full speed\n"); + TU_LOG3("Full speed\r\n"); } new_mode |= MODE_SOFKAENAB; mode_write(rhport, new_mode, in_isr); diff --git a/src/portable/ehci/ehci.c b/src/portable/ehci/ehci.c index 572b9826c..e145cbb1b 100644 --- a/src/portable/ehci/ehci.c +++ b/src/portable/ehci/ehci.c @@ -581,7 +581,7 @@ void qhd_xfer_complete_isr(ehci_qhd_t * qhd) { // clear halted bit if not caused by STALL to allow more transfer xfer_result = XFER_RESULT_FAILED; qtd_overlay->halted = false; - TU_LOG3(" QHD xfer err count: %d\n", qtd_overlay->err_count); + TU_LOG3(" QHD xfer err count: %d\r\n", qtd_overlay->err_count); // TU_BREAKPOINT(); // TODO skip unplugged device }else { // no error bits are set, endpoint is halted due to STALL @@ -664,7 +664,7 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { if (int_status & EHCI_INT_MASK_HC_HALTED) { // something seriously wrong, maybe forget to flush/invalidate cache TU_BREAKPOINT(); - TU_LOG1(" HC halted\n"); + TU_LOG1(" HC halted\r\n"); return; } diff --git a/src/portable/mentor/musb/dcd_musb.c b/src/portable/mentor/musb/dcd_musb.c index 3c0114e41..a817c5d6e 100644 --- a/src/portable/mentor/musb/dcd_musb.c +++ b/src/portable/mentor/musb/dcd_musb.c @@ -158,9 +158,9 @@ static inline unsigned free_block_size(free_block_t const *blk) #if 0 static inline void print_block_list(free_block_t const *blk, unsigned num) { - TU_LOG1("*************\n"); + TU_LOG1("*************\r\n"); for (unsigned i = 0; i < num; ++i) { - TU_LOG1(" Blk%u %u %u\n", i, blk->beg, blk->end); + TU_LOG1(" Blk%u %u %u\r\n", i, blk->beg, blk->end); ++blk; } } -- cgit v1.3.1 From 93c40b6966db53ce70f4bea6b8a72bf2986ac180 Mon Sep 17 00:00:00 2001 From: henneboi Date: Fri, 8 Dec 2023 13:34:42 +0100 Subject: Add Support stm32h5 for stm32h573i based on stm32_fsdev G0 implementation Tested on Windows with IAR and gcc toolchain ( via cubeide) Tested only with audio examples, but sould be ok for other examples Cmake pacthed : but not tested Linux build : not tested Added a temporary workaround in make file to support H5 HAL repo ( ARMCC_VERSION=0) --- hw/bsp/board_mcu.h | 11 +- hw/bsp/stm32h5/FreeRTOSConfig/FreeRTOSConfig.h | 165 ++++++++++ .../boards/stm32h573i-dk/STM32H573I-DK_FLASH.ld | 187 +++++++++++ hw/bsp/stm32h5/boards/stm32h573i-dk/board.cmake | 10 + hw/bsp/stm32h5/boards/stm32h573i-dk/board.h | 125 ++++++++ hw/bsp/stm32h5/boards/stm32h573i-dk/board.mk | 13 + hw/bsp/stm32h5/family.c | 206 ++++++++++++ hw/bsp/stm32h5/family.cmake | 116 +++++++ hw/bsp/stm32h5/family.mk | 57 ++++ hw/bsp/stm32h5/stm32h5xx_hal_conf.h | 355 +++++++++++++++++++++ src/common/tusb_mcu.h | 6 + src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 11 +- .../st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 29 ++ src/tusb_option.h | 1 + tools/get_deps.py | 9 +- 15 files changed, 1295 insertions(+), 6 deletions(-) create mode 100644 hw/bsp/stm32h5/FreeRTOSConfig/FreeRTOSConfig.h create mode 100644 hw/bsp/stm32h5/boards/stm32h573i-dk/STM32H573I-DK_FLASH.ld create mode 100644 hw/bsp/stm32h5/boards/stm32h573i-dk/board.cmake create mode 100644 hw/bsp/stm32h5/boards/stm32h573i-dk/board.h create mode 100644 hw/bsp/stm32h5/boards/stm32h573i-dk/board.mk create mode 100644 hw/bsp/stm32h5/family.c create mode 100644 hw/bsp/stm32h5/family.cmake create mode 100644 hw/bsp/stm32h5/family.mk create mode 100644 hw/bsp/stm32h5/stm32h5xx_hal_conf.h (limited to 'src/portable') diff --git a/hw/bsp/board_mcu.h b/hw/bsp/board_mcu.h index 4ce5c4139..d40f33bbe 100644 --- a/hw/bsp/board_mcu.h +++ b/hw/bsp/board_mcu.h @@ -40,8 +40,8 @@ // Include order follows OPT_MCU_ number #if TU_CHECK_MCU(OPT_MCU_LPC11UXX, OPT_MCU_LPC13XX, OPT_MCU_LPC15XX) || \ - TU_CHECK_MCU(OPT_MCU_LPC175X_6X, OPT_MCU_LPC177X_8X, OPT_MCU_LPC18XX) || \ - TU_CHECK_MCU(OPT_MCU_LPC40XX, OPT_MCU_LPC43XX) + TU_CHECK_MCU(OPT_MCU_LPC175X_6X, OPT_MCU_LPC177X_8X, OPT_MCU_LPC18XX) || \ + TU_CHECK_MCU(OPT_MCU_LPC40XX, OPT_MCU_LPC43XX) #include "chip.h" #elif TU_CHECK_MCU(OPT_MCU_LPC51UXX, OPT_MCU_LPC54XXX, OPT_MCU_LPC55XX, OPT_MCU_MCXN9) @@ -54,8 +54,8 @@ #include "nrf.h" #elif CFG_TUSB_MCU == OPT_MCU_SAMD11 || CFG_TUSB_MCU == OPT_MCU_SAMD21 || \ - CFG_TUSB_MCU == OPT_MCU_SAMD51 || CFG_TUSB_MCU == OPT_MCU_SAME5X || \ - CFG_TUSB_MCU == OPT_MCU_SAML22 || CFG_TUSB_MCU == OPT_MCU_SAML21 + CFG_TUSB_MCU == OPT_MCU_SAMD51 || CFG_TUSB_MCU == OPT_MCU_SAME5X || \ + CFG_TUSB_MCU == OPT_MCU_SAML22 || CFG_TUSB_MCU == OPT_MCU_SAML21 #include "sam.h" #elif CFG_TUSB_MCU == OPT_MCU_SAMG @@ -83,6 +83,9 @@ #elif CFG_TUSB_MCU == OPT_MCU_STM32G4 #include "stm32g4xx.h" +#elif CFG_TUSB_MCU == OPT_MCU_STM32H5 + #include "stm32h5xx.h" + #elif CFG_TUSB_MCU == OPT_MCU_STM32H7 #include "stm32h7xx.h" diff --git a/hw/bsp/stm32h5/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/stm32h5/FreeRTOSConfig/FreeRTOSConfig.h new file mode 100644 index 000000000..52dfa095f --- /dev/null +++ b/hw/bsp/stm32h5/FreeRTOSConfig/FreeRTOSConfig.h @@ -0,0 +1,165 @@ +/* + * FreeRTOS Kernel V10.0.0 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. If you wish to use our Amazon + * FreeRTOS name, please do so in a fair use way that does not cause confusion. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + + +#ifndef FREERTOS_CONFIG_H +#define FREERTOS_CONFIG_H + +/*----------------------------------------------------------- + * Application specific definitions. + * + * These definitions should be adjusted for your particular hardware and + * application requirements. + * + * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE + * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. + * + * See http://www.freertos.org/a00110.html. + *----------------------------------------------------------*/ + +// skip if included from IAR assembler +#ifndef __IASMARM__ + #include "stm32g0xx.h" +#endif + +/* Cortex M23/M33 port configuration. */ +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) + +#define configUSE_PREEMPTION 1 +#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 +#define configCPU_CLOCK_HZ SystemCoreClock +#define configTICK_RATE_HZ ( 1000 ) +#define configMAX_PRIORITIES ( 5 ) +#define configMINIMAL_STACK_SIZE ( 128 ) +#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) +#define configMAX_TASK_NAME_LEN 16 +#define configUSE_16_BIT_TICKS 0 +#define configIDLE_SHOULD_YIELD 1 +#define configUSE_MUTEXES 1 +#define configUSE_RECURSIVE_MUTEXES 1 +#define configUSE_COUNTING_SEMAPHORES 1 +#define configQUEUE_REGISTRY_SIZE 4 +#define configUSE_QUEUE_SETS 0 +#define configUSE_TIME_SLICING 0 +#define configUSE_NEWLIB_REENTRANT 0 +#define configENABLE_BACKWARD_COMPATIBILITY 1 +#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 + +#define configSUPPORT_STATIC_ALLOCATION 1 +#define configSUPPORT_DYNAMIC_ALLOCATION 0 + +/* Hook function related definitions. */ +#define configUSE_IDLE_HOOK 0 +#define configUSE_TICK_HOOK 0 +#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning +#define configCHECK_FOR_STACK_OVERFLOW 2 + +/* Run time and task stats gathering related definitions. */ +#define configGENERATE_RUN_TIME_STATS 0 +#define configRECORD_STACK_HIGH_ADDRESS 1 +#define configUSE_TRACE_FACILITY 1 // legacy trace +#define configUSE_STATS_FORMATTING_FUNCTIONS 0 + +/* Co-routine definitions. */ +#define configUSE_CO_ROUTINES 0 +#define configMAX_CO_ROUTINE_PRIORITIES 2 + +/* Software timer related definitions. */ +#define configUSE_TIMERS 1 +#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) +#define configTIMER_QUEUE_LENGTH 32 +#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE + +/* Optional functions - most linkers will remove unused functions anyway. */ +#define INCLUDE_vTaskPrioritySet 0 +#define INCLUDE_uxTaskPriorityGet 0 +#define INCLUDE_vTaskDelete 0 +#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY +#define INCLUDE_xResumeFromISR 0 +#define INCLUDE_vTaskDelayUntil 1 +#define INCLUDE_vTaskDelay 1 +#define INCLUDE_xTaskGetSchedulerState 0 +#define INCLUDE_xTaskGetCurrentTaskHandle 1 +#define INCLUDE_uxTaskGetStackHighWaterMark 0 +#define INCLUDE_xTaskGetIdleTaskHandle 0 +#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 +#define INCLUDE_pcTaskGetTaskName 0 +#define INCLUDE_eTaskGetState 0 +#define INCLUDE_xEventGroupSetBitFromISR 0 +#define INCLUDE_xTimerPendFunctionCall 0 + +/* Define to trap errors during development. */ +// Halt CPU (breakpoint) when hitting error, only apply for Cortex M3, M4, M7 +#if defined(__ARM_ARCH_7M__) || defined (__ARM_ARCH_7EM__) +#define configASSERT(_exp) \ + do {\ + if ( !(_exp) ) { \ + volatile uint32_t* ARM_CM_DHCSR = ((volatile uint32_t*) 0xE000EDF0UL); /* Cortex M CoreDebug->DHCSR */ \ + if ( (*ARM_CM_DHCSR) & 1UL ) { /* Only halt mcu if debugger is attached */ \ + taskDISABLE_INTERRUPTS(); \ + __asm("BKPT #0\n"); \ + }\ + }\ + } while(0) +#else +#define configASSERT( x ) +#endif + +/* FreeRTOS hooks to NVIC vectors */ +#define xPortPendSVHandler PendSV_Handler +#define xPortSysTickHandler SysTick_Handler +#define vPortSVCHandler SVC_Handler + +//--------------------------------------------------------------------+ +// Interrupt nesting behavior configuration. +//--------------------------------------------------------------------+ + +// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header +#define configPRIO_BITS 2 + +/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1<
© COPYRIGHT(c) 2019 STMicroelectronics
+** +** Redistribution and use in source and binary forms, with or without modification, +** are permitted provided that the following conditions are met: +** 1. Redistributions of source code must retain the above copyright notice, +** this list of conditions and the following disclaimer. +** 2. Redistributions in binary form must reproduce the above copyright notice, +** this list of conditions and the following disclaimer in the documentation +** and/or other materials provided with the distribution. +** 3. Neither the name of STMicroelectronics nor the names of its contributors +** may be used to endorse or promote products derived from this software +** without specific prior written permission. +** +** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE +** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE +** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL +** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR +** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER +** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, +** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE +** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 640K +FLASH (rx) : ORIGIN = 0x8000000, LENGTH = 2048K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss section */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/hw/bsp/stm32h5/boards/stm32h573i-dk/board.cmake b/hw/bsp/stm32h5/boards/stm32h573i-dk/board.cmake new file mode 100644 index 000000000..82d4474af --- /dev/null +++ b/hw/bsp/stm32h5/boards/stm32h573i-dk/board.cmake @@ -0,0 +1,10 @@ +set(MCU_VARIANT stm32h573i-dk) +set(JLINK_DEVICE stm32h573i-dk) + +set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32H573I-DK_FLASH.ld) + +function(update_board TARGET) + target_compile_definitions(${TARGET} PUBLIC + STM32H573xx + ) +endfunction() diff --git a/hw/bsp/stm32h5/boards/stm32h573i-dk/board.h b/hw/bsp/stm32h5/boards/stm32h573i-dk/board.h new file mode 100644 index 000000000..01834f151 --- /dev/null +++ b/hw/bsp/stm32h5/boards/stm32h573i-dk/board.h @@ -0,0 +1,125 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020, Ha Thach (tinyusb.org) + * Copyright (c) 2034, HiFiPhile + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +// LED +#define LED_PORT GPIOI +#define LED_PIN GPIO_PIN_9 +#define LED_STATE_ON 0 + +// Button +#define BUTTON_PORT GPIOC +#define BUTTON_PIN GPIO_PIN_13 +#define BUTTON_STATE_ACTIVE 0 + +// UART Enable for STLink VCOM +#define UART_DEV USART1 +#define UART_CLK_EN __USART1_CLK_ENABLE +#define UART_GPIO_PORT GPIOA +#define UART_GPIO_AF GPIO_AF7_USART1 + +#define UART_TX_PIN GPIO_PIN_9 +#define UART_RX_PIN GPIO_PIN_10 + + + + +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +// Clock configure for STM32stm32h573i-dk +static inline void board_clock_init(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {0}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; + + /** Configure the main internal regulator output voltage */ + HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1); + + /** Initializes the RCC Oscillators according to the specified parameters + * in the RCC_OscInitTypeDef structure. + Freq 250MHZ */ + + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48 | RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS_DIGITAL; + RCC_OscInitStruct.HSI48State = RCC_HSI48_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLL1_SOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = 5; + RCC_OscInitStruct.PLL.PLLN = 100; + RCC_OscInitStruct.PLL.PLLP = 2; + RCC_OscInitStruct.PLL.PLLQ = 10; + RCC_OscInitStruct.PLL.PLLR = 2; + RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1_VCIRANGE_2; + RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1_VCORANGE_WIDE; + RCC_OscInitStruct.PLL.PLLFRACN = 0; + HAL_RCC_OscConfig(&RCC_OscInitStruct); + + /** Initializes the CPU, AHB and APB buses clocks */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5); + + // Configure CRS clock source + __HAL_RCC_CRS_CLK_ENABLE(); + RCC_CRSInitTypeDef RCC_CRSInitStruct = {0}; + RCC_CRSInitStruct.Prescaler = RCC_CRS_SYNC_DIV1; + RCC_CRSInitStruct.Source = RCC_CRS_SYNC_SOURCE_USB; + RCC_CRSInitStruct.Polarity = RCC_CRS_SYNC_POLARITY_RISING; + RCC_CRSInitStruct.ReloadValue = __HAL_RCC_CRS_RELOADVALUE_CALCULATE(48000000, 1000); + RCC_CRSInitStruct.ErrorLimitValue = 34; + RCC_CRSInitStruct.HSI48CalibrationValue = 32; + HAL_RCCEx_CRSConfig(&RCC_CRSInitStruct); + + + /* Select HSI48 as USB clock source */ + RCC_PeriphCLKInitTypeDef usb_clk = {0 }; + usb_clk.PeriphClockSelection = RCC_PERIPHCLK_USB; + usb_clk.UsbClockSelection = RCC_USBCLKSOURCE_HSI48; + HAL_RCCEx_PeriphCLKConfig(&usb_clk); + + /* Peripheral clock enable */ + __HAL_RCC_USB_CLK_ENABLE(); + + SystemCoreClockUpdate(); + + +} + +#ifdef __cplusplus +} +#endif + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/stm32h5/boards/stm32h573i-dk/board.mk b/hw/bsp/stm32h5/boards/stm32h573i-dk/board.mk new file mode 100644 index 000000000..66b299886 --- /dev/null +++ b/hw/bsp/stm32h5/boards/stm32h573i-dk/board.mk @@ -0,0 +1,13 @@ +CFLAGS += \ + -DSTM32H573xx + +# GCC +SRC_S_GCC += $(ST_CMSIS)/Source/Templates/gcc/startup_stm32h573xx.s +LD_FILE_GCC = $(BOARD_PATH)/STM32H573I-DK_FLASH.ld + +# IAR +SRC_S_IAR += $(ST_CMSIS)/Source/Templates/iar/startup_stm32h573xx.s +LD_FILE_IAR = $(ST_CMSIS)/Source/Templates/iar/linker/stm32h573xx_flash.icf + +# For flash-jlink target +JLINK_DEVICE = stm32h573i-dk diff --git a/hw/bsp/stm32h5/family.c b/hw/bsp/stm32h5/family.c new file mode 100644 index 000000000..d035b791c --- /dev/null +++ b/hw/bsp/stm32h5/family.c @@ -0,0 +1,206 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * Copyright (c) 2023 HiFiPhile + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "stm32h5xx_hal.h" +#include "bsp/board_api.h" +#include "board.h" + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB_DRD_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ +UART_HandleTypeDef UartHandle; + +void board_init(void) +{ + HAL_Init(); // required for HAL_RCC_Osc TODO check with freeRTOS + board_clock_init(); + + // Enable All GPIOs clocks + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); + __HAL_RCC_GPIOE_CLK_ENABLE(); + __HAL_RCC_GPIOI_CLK_ENABLE(); + + //__HAL_RCC_SYSCFG_CLK_ENABLE(); + //__HAL_RCC_PWR_CLK_ENABLE(); + + UART_CLK_EN(); + + #if CFG_TUSB_OS == OPT_OS_NONE + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + #elif CFG_TUSB_OS == OPT_OS_FREERTOS + // Explicitly disable systick to prevent its ISR runs before scheduler start + SysTick->CTRL &= ~1U; + + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(USB_DRD_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + #endif + + GPIO_InitTypeDef GPIO_InitStruct; + + // LED + GPIO_InitStruct.Pin = LED_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(LED_PORT, &GPIO_InitStruct); + + board_led_write(false); + + // Button + GPIO_InitStruct.Pin = BUTTON_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = BUTTON_STATE_ACTIVE ? GPIO_PULLDOWN : GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(BUTTON_PORT, &GPIO_InitStruct); + + #ifdef UART_DEV + // UART + GPIO_InitStruct.Pin = UART_TX_PIN | UART_RX_PIN; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_PULLUP; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + GPIO_InitStruct.Alternate = UART_GPIO_AF; + HAL_GPIO_Init(UART_GPIO_PORT, &GPIO_InitStruct); + + UartHandle = (UART_HandleTypeDef) + { + .Instance = UART_DEV, + .Init.BaudRate = CFG_BOARD_UART_BAUDRATE, + .Init.WordLength = UART_WORDLENGTH_8B, + .Init.StopBits = UART_STOPBITS_1, + .Init.Parity = UART_PARITY_NONE, + .Init.HwFlowCtl = UART_HWCONTROL_NONE, + .Init.Mode = UART_MODE_TX_RX, + .Init.OverSampling = UART_OVERSAMPLING_16, + .AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT + }; + HAL_UART_Init(&UartHandle); + #endif + + // USB Pins TODO double check USB clock and pin setup + // Configure USB DM and DP pins. This is optional, and maintained only for user guidance. + GPIO_InitStruct.Pin = (GPIO_PIN_11 | GPIO_PIN_12); + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /* Peripheral clock enable */ + __HAL_RCC_USB_CLK_ENABLE(); + + /* Enable VDDUSB */ + HAL_PWREx_EnableVddUSB(); +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + GPIO_PinState pin_state = (GPIO_PinState)(state ? LED_STATE_ON : (1 - LED_STATE_ON)); + HAL_GPIO_WritePin(LED_PORT, LED_PIN, pin_state); +} + +uint32_t board_button_read(void) +{ + return BUTTON_STATE_ACTIVE == HAL_GPIO_ReadPin(BUTTON_PORT, BUTTON_PIN); +} + +size_t board_get_unique_id(uint8_t id[], size_t max_len) +{ + (void) max_len; + volatile uint32_t *stm32_uuid = (volatile uint32_t *) UID_BASE; + uint32_t *id32 = (uint32_t *)(uintptr_t) id; + uint8_t const len = 12; + + id32[0] = stm32_uuid[0]; + id32[1] = stm32_uuid[1]; + id32[2] = stm32_uuid[2]; + + return len; +} + +int board_uart_read(uint8_t *buf, int len) +{ + (void) buf; + (void) len; + return 0; +} + +int board_uart_write(void const *buf, int len) +{ + #ifdef UART_DEV + HAL_UART_Transmit(&UartHandle, (uint8_t *)(uintptr_t) buf, len, 0xffff); + return len; + #else + (void) buf; + (void) len; + (void) UartHandle; + return 0; + #endif +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; + +void SysTick_Handler(void) +{ + system_ticks++; + HAL_IncTick(); +} + +uint32_t board_millis(void) +{ + return system_ticks; +} + +#endif + +void HardFault_Handler(void) +{ + __asm("BKPT #0\n"); +} + +// Required by __libc_init_array in startup code if we are compiling using +// -nostdlib/-nostartfiles. +void _init(void) +{ + +} diff --git a/hw/bsp/stm32h5/family.cmake b/hw/bsp/stm32h5/family.cmake new file mode 100644 index 000000000..8edee1887 --- /dev/null +++ b/hw/bsp/stm32h5/family.cmake @@ -0,0 +1,116 @@ +include_guard() + +if (NOT BOARD) + message(FATAL_ERROR "BOARD not specified") +endif () + +set(ST_FAMILY h5) +set(ST_PREFIX stm32${ST_FAMILY}xx) + +set(ST_HAL_DRIVER ${TOP}/hw/mcu/st/stm32${ST_FAMILY}xx_hal_driver) +set(ST_CMSIS ${TOP}/hw/mcu/st/cmsis_device_${ST_FAMILY}) +set(CMSIS_5 ${TOP}/lib/CMSIS_5) + +# include board specific +include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) + +# toolchain set up +set(CMAKE_SYSTEM_PROCESSOR cortex-m0plus CACHE INTERNAL "System Processor") +set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOLCHAIN}.cmake) + +set(FAMILY_MCUS STM32H5 CACHE INTERNAL "") + + +#------------------------------------ +# BOARD_TARGET +#------------------------------------ +# only need to be built ONCE for all examples +function(add_board_target BOARD_TARGET) + if (NOT TARGET ${BOARD_TARGET}) + # Startup & Linker script + set(STARTUP_FILE_GNU ${ST_CMSIS}/Source/Templates/gcc/startup_${MCU_VARIANT}.s) + set(STARTUP_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/startup_${MCU_VARIANT}.s) + set(LD_FILE_IAR ${ST_CMSIS}/Source/Templates/iar/linker/${MCU_VARIANT}_flash.icf) + + add_library(${BOARD_TARGET} STATIC + ${ST_CMSIS}/Source/Templates/system_${ST_PREFIX}.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_cortex.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_pwr.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_pwr_ex.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_rcc_ex.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_gpio.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_uart.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_uart_ex.c + ${ST_HAL_DRIVER}/Src/${ST_PREFIX}_hal_dma.c + ${STARTUP_FILE_${CMAKE_C_COMPILER_ID}} + ) + target_include_directories(${BOARD_TARGET} PUBLIC + ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + ${CMSIS_5}/CMSIS/Core/Include + ${ST_CMSIS}/Include + ${ST_HAL_DRIVER}/Inc + ) + target_compile_options(${BOARD_TARGET} PUBLIC + ) + target_compile_definitions(${BOARD_TARGET} PUBLIC + ) + + update_board(${BOARD_TARGET}) + + if (CMAKE_C_COMPILER_ID STREQUAL "GNU") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--script=${LD_FILE_GNU}" + -nostartfiles + # nanolib + --specs=nosys.specs + --specs=nano.specs + ) + elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--config=${LD_FILE_IAR}" + ) + endif () + endif () +endfunction() + + +#------------------------------------ +# Functions +#------------------------------------ +function(family_configure_example TARGET RTOS) + family_configure_common(${TARGET} ${RTOS}) + + # Board target + add_board_target(board_${BOARD}) + + #---------- Port Specific ---------- + # These files are built for each example since it depends on example's tusb_config.h + target_sources(${TARGET} PUBLIC + # BSP + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c + ) + target_include_directories(${TARGET} PUBLIC + # family, hw, board + ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../ + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} + ) + + # Add TinyUSB target and port source + family_add_tinyusb(${TARGET} OPT_MCU_STM32H5 ${RTOS}) + target_sources(${TARGET}-tinyusb PUBLIC + ${TOP}/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c + ${TOP}/src/portable/st/typec/typec_stm32.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) + + # Link dependencies + target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) + + # Flashing + family_flash_stlink(${TARGET}) + #family_flash_jlink(${TARGET}) +endfunction() diff --git a/hw/bsp/stm32h5/family.mk b/hw/bsp/stm32h5/family.mk new file mode 100644 index 000000000..e04e08d80 --- /dev/null +++ b/hw/bsp/stm32h5/family.mk @@ -0,0 +1,57 @@ +ST_FAMILY = h5 +DEPS_SUBMODULES += lib/CMSIS_5 hw/mcu/st/cmsis_device_$(ST_FAMILY) hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver + +ST_CMSIS = hw/mcu/st/cmsis_device_$(ST_FAMILY) +ST_HAL_DRIVER = hw/mcu/st/stm32$(ST_FAMILY)xx_hal_driver + +include $(TOP)/$(BOARD_PATH)/board.mk +CPU_CORE ?= cortex-m33 + +# -------------- +# Compiler Flags +# -------------- +CFLAGS += \ + -DCFG_TUSB_MCU=OPT_MCU_STM32H5 + +# workaround to fix a build issue due to a wrong define check in hal, this define must be removed as soon as the repo is fixed +CFLAGS += \ + -D__ARMCC_VERSION=0 + +# GCC Flags +CFLAGS_GCC += \ + -flto \ + -nostdlib -nostartfiles \ + -Wno-unused-parameter \ + -Wno-cast-align + +# suppress warning caused by vendor mcu driver +CFLAGS_GCC += -Wno-error=cast-align + +#LDFLAGS_GCC += -specs=nosys.specs -specs=nano.specs + +# ----------------- +# Sources & Include +# ----------------- + +SRC_C += \ + src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c \ + $(ST_CMSIS)/Source/Templates/system_stm32$(ST_FAMILY)xx.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_cortex.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_pwr_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_rcc_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_uart_ex.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_gpio.c \ + $(ST_HAL_DRIVER)/Src/stm32$(ST_FAMILY)xx_hal_dma.c + +INC += \ + $(TOP)/$(BOARD_PATH) \ + $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ + $(TOP)/$(ST_CMSIS)/Include \ + $(TOP)/$(ST_HAL_DRIVER)/Inc + +# flash target using on-board stlink +flash: flash-stlink diff --git a/hw/bsp/stm32h5/stm32h5xx_hal_conf.h b/hw/bsp/stm32h5/stm32h5xx_hal_conf.h new file mode 100644 index 000000000..d017bb06b --- /dev/null +++ b/hw/bsp/stm32h5/stm32h5xx_hal_conf.h @@ -0,0 +1,355 @@ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * @file stm32h5xx_hal_conf.h + * @author MCD Application Team + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + * Copyright (c) 2018-2021 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + */ +/* USER CODE END Header */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef STM32h5xx_HAL_CONF_H +#define STM32h5xx_HAL_CONF_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +/* #define HAL_ADC_MODULE_ENABLED */ +/* #define HAL_CEC_MODULE_ENABLED */ +/* #define HAL_COMP_MODULE_ENABLED */ +/* #define HAL_CRC_MODULE_ENABLED */ +/* #define HAL_CRYP_MODULE_ENABLED */ +/* #define HAL_DAC_MODULE_ENABLED */ +/* #define HAL_EXTI_MODULE_ENABLED */ +/* #define HAL_FDCAN_MODULE_ENABLED */ +/* #define HAL_HCD_MODULE_ENABLED */ +/* #define HAL_I2C_MODULE_ENABLED */ +/* #define HAL_I2S_MODULE_ENABLED */ +/* #define HAL_IWDG_MODULE_ENABLED */ +/* #define HAL_IRDA_MODULE_ENABLED */ +/* #define HAL_LPTIM_MODULE_ENABLED */ +/* #define HAL_PCD_MODULE_ENABLED */ +/* #define HAL_RNG_MODULE_ENABLED */ +/* #define HAL_RTC_MODULE_ENABLED */ +/* #define HAL_SMARTCARD_MODULE_ENABLED */ +/* #define HAL_SMBUS_MODULE_ENABLED */ +/* #define HAL_SPI_MODULE_ENABLED */ +/* #define HAL_TIM_MODULE_ENABLED */ +/* #define HAL_USART_MODULE_ENABLED */ +/* #define HAL_WWDG_MODULE_ENABLED */ +#define HAL_GPIO_MODULE_ENABLED +#define HAL_EXTI_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_CORTEX_MODULE_ENABLED +#define HAL_UART_MODULE_ENABLED + +/* ########################## Register Callbacks selection ############################## */ +/** + * @brief This is the list of modules where register callback can be used + */ +#define USE_HAL_ADC_REGISTER_CALLBACKS 0u +#define USE_HAL_CEC_REGISTER_CALLBACKS 0u +#define USE_HAL_COMP_REGISTER_CALLBACKS 0u +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0u +#define USE_HAL_DAC_REGISTER_CALLBACKS 0u +#define USE_HAL_FDCAN_REGISTER_CALLBACKS 0u +#define USE_HAL_HCD_REGISTER_CALLBACKS 0u +#define USE_HAL_I2C_REGISTER_CALLBACKS 0u +#define USE_HAL_I2S_REGISTER_CALLBACKS 0u +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0u +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0u +#define USE_HAL_PCD_REGISTER_CALLBACKS 0u +#define USE_HAL_RNG_REGISTER_CALLBACKS 0u +#define USE_HAL_RTC_REGISTER_CALLBACKS 0u +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0u +#define USE_HAL_SPI_REGISTER_CALLBACKS 0u +#define USE_HAL_TIM_REGISTER_CALLBACKS 0u +#define USE_HAL_UART_REGISTER_CALLBACKS 0u +#define USE_HAL_USART_REGISTER_CALLBACKS 0u +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0u + + +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#if !defined (HSE_VALUE) +#define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#if !defined (HSE_STARTUP_TIMEOUT) +#define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal Core Speed oscillator (CSI) default value. + * This value is the default CSI range value after Reset. + */ +#if !defined (CSI_VALUE) +#define CSI_VALUE 4000000UL /*!< Value of the Internal oscillator in Hz*/ +#endif /* CSI_VALUE */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#if !defined (HSI_VALUE) +#define HSI_VALUE 64000000UL /*!< Value of the Internal oscillator in Hz*/ +#endif /* HSI_VALUE */ + +/** + * @brief Internal High Speed oscillator (HSI48) value for USB FS, SDMMC and RNG. + * This internal oscillator is mainly dedicated to provide a high precision clock to + * the USB peripheral by means of a special Clock Recovery System (CRS) circuitry. + * When the CRS is not used, the HSI48 RC oscillator runs on it default frequency + * which is subject to manufacturing process variations. + */ +#if !defined (HSI48_VALUE) +#define HSI48_VALUE 48000000UL /*!< Value of the Internal High Speed oscillator for USB FS/SDMMC/RNG in Hz. + The real value my vary depending on manufacturing process variations.*/ +#endif /* HSI48_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#if !defined (LSI_VALUE) +#define LSI_VALUE 32000UL /*!< LSI Typical Value in Hz*/ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz +The real value may vary depending on the variations +in voltage and temperature.*/ + +#if !defined (LSI_STARTUP_TIME) +#define LSI_STARTUP_TIME 130UL /*!< Time out for LSI start up, in ms */ +#endif /* LSI_STARTUP_TIME */ + +/** + * @brief External Low Speed oscillator (LSE) value. + * This value is used by the UART, RTC HAL module to compute the system frequency + */ +#if !defined (LSE_VALUE) +#define LSE_VALUE 32768UL /*!< Value of the External oscillator in Hz*/ +#endif /* LSE_VALUE */ + +#if !defined (LSE_STARTUP_TIMEOUT) +#define LSE_STARTUP_TIMEOUT 5000UL /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for SPI/SAI peripheral + * This value is used by the SPI/SAI HAL module to compute the SPI/SAI clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + + */ +#if !defined (EXTERNAL_CLOCK_VALUE) +#define EXTERNAL_CLOCK_VALUE 12288000UL /*!< Value of the External clock in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ############################################ System Configuration ################################################ */ + +/** + * @brief This is the HAL system configuration section + */ + +#define VDD_VALUE 3300UL /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY (15UL) /*!< tick interrupt priority (lowest by default) */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 0U /*!< Enable prefetch */ + + + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 0U + +/* ################## CRYP peripheral configuration ########################## */ + +#define USE_HAL_CRYP_SUSPEND_RESUME 1U + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1U */ + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include modules header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED +#include "stm32h5xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED +#include "stm32h5xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED +#include "stm32h5xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED +#include "stm32h5xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED +#include "stm32h5xx_hal_adc.h" +#include "stm32h5xx_hal_adc_ex.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED +#include "stm32h5xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_COMP_MODULE_ENABLED +#include "stm32h5xx_hal_comp.h" +#endif /* HAL_COMP_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED +#include "stm32h5xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED +#include "stm32h5xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED +#include "stm32h5xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED +#include "stm32h5xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED +#include "stm32h5xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_FDCAN_MODULE_ENABLED +#include "stm32h5xx_hal_fdcan.h" +#endif /* HAL_FDCAN_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED +#include "stm32h5xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED +#include "stm32h5xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED +#include "stm32h5xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED +#include "stm32h5xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED +#include "stm32h5xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32h5xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED +#include "stm32h5xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED +#include "stm32h5xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED +#include "stm32h5xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED +#include "stm32h5xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED +#include "stm32h5xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED +#include "stm32h5xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED +#include "stm32h5xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED +#include "stm32h5xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED +#include "stm32h5xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED +#include "stm32h5xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED +#include "stm32h5xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for functions parameters check. + * @param expr If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ +#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ +void assert_failed(uint8_t *file, uint32_t line); +#else +#define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* STM32h5xx_HAL_CONF_H */ diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 6fab190ea..9c4083031 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -210,6 +210,12 @@ #define TUP_DCD_ENDPOINT_MAX 9 +#elif TU_CHECK_MCU(OPT_MCU_STM32H5) + #define TUP_USBIP_FSDEV + #define TUP_USBIP_FSDEV_STM32 + #define TUP_DCD_ENDPOINT_MAX 8 + + #elif TU_CHECK_MCU(OPT_MCU_STM32G4) // Device controller #define TUP_USBIP_FSDEV diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 14cabaf8d..b0a00b7ee 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -242,7 +242,7 @@ void dcd_init (uint8_t rhport) } USB->CNTR = 0; // Enable USB -#ifndef STM32G0 // BTABLE register does not exist any more on STM32G0, it is fixed to USB SRAM base address +#if !defined(STM32G0) && !defined(STM32H5) // BTABLE register does not exist any more on STM32G0, it is fixed to USB SRAM base address USB->BTABLE = DCD_STM32_BTABLE_BASE; #endif USB->ISTR = 0; // Clear pending interrupts @@ -357,6 +357,11 @@ void dcd_int_enable (uint8_t rhport) #else NVIC_EnableIRQ(USB_UCPD1_2_IRQn); #endif + + +#elif CFG_TUSB_MCU == OPT_MCU_STM32H5 + NVIC_EnableIRQ(USB_DRD_FS_IRQn); + #elif CFG_TUSB_MCU == OPT_MCU_STM32WB NVIC_EnableIRQ(USB_HP_IRQn); @@ -414,6 +419,10 @@ void dcd_int_disable(uint8_t rhport) #else NVIC_DisableIRQ(USB_UCPD1_2_IRQn); #endif + +#elif CFG_TUSB_MCU == OPT_MCU_STM32H5 + NVIC_DisableIRQ(USB_DRD_FS_IRQn); + #elif CFG_TUSB_MCU == OPT_MCU_STM32WB NVIC_DisableIRQ(USB_HP_IRQn); diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index e6649de5a..0db426e50 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -110,6 +110,35 @@ #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY #define USB_CNTR_FSUSP USB_CNTR_SUSPEN +#elif CFG_TUSB_MCU == OPT_MCU_STM32H5 + #include "stm32h5xx.h" + #define PMA_32BIT_ACCESS + #define PMA_LENGTH (2048u) + #undef USB_PMAADDR + #define USB_PMAADDR USB_DRD_PMAADDR + #define USB_TypeDef USB_DRD_TypeDef + #define EP0R CHEP0R + #define USB_EP_CTR_RX USB_EP_VTRX + #define USB_EP_CTR_TX USB_EP_VTTX + #define USB_EP_T_FIELD USB_CHEP_UTYPE + #define USB_EPREG_MASK USB_CHEP_REG_MASK + #define USB_EPTX_DTOGMASK USB_CHEP_TX_DTOGMASK + #define USB_EPRX_DTOGMASK USB_CHEP_RX_DTOGMASK + #define USB_EPTX_DTOG1 USB_CHEP_TX_DTOG1 + #define USB_EPTX_DTOG2 USB_CHEP_TX_DTOG2 + #define USB_EPRX_DTOG1 USB_CHEP_RX_DTOG1 + #define USB_EPRX_DTOG2 USB_CHEP_RX_DTOG2 + #define USB_EPRX_STAT USB_CH_RX_VALID + #define USB_EPKIND_MASK USB_EP_KIND_MASK + #define USB USB_DRD_FS + #define USB_CNTR_FRES USB_CNTR_USBRST + #define USB_CNTR_RESUME USB_CNTR_L2RES + #define USB_ISTR_EP_ID USB_ISTR_IDN + #define USB_EPADDR_FIELD USB_CHEP_ADDR + #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY + #define USB_CNTR_FSUSP USB_CNTR_SUSPEN + + #elif CFG_TUSB_MCU == OPT_MCU_STM32WB #include "stm32wbxx.h" #define PMA_LENGTH (1024u) diff --git a/src/tusb_option.h b/src/tusb_option.h index 7597392d6..699691b53 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -86,6 +86,7 @@ #define OPT_MCU_STM32WB 312 ///< ST WB #define OPT_MCU_STM32U5 313 ///< ST U5 #define OPT_MCU_STM32L5 314 ///< ST L5 +#define OPT_MCU_STM32H5 315 ///< ST H5 // Sony #define OPT_MCU_CXD56 400 ///< SONY CXD56 diff --git a/tools/get_deps.py b/tools/get_deps.py index 79c272c07..cda4fc8da 100644 --- a/tools/get_deps.py +++ b/tools/get_deps.py @@ -95,6 +95,10 @@ deps_optional = { 'hw/mcu/st/cmsis_device_h7': ['https://github.com/STMicroelectronics/cmsis_device_h7.git', '60dc2c913203dc8629dc233d4384dcc41c91e77f', 'stm32h7'], + 'hw/mcu/st/cmsis_device_h5': ['https://github.com/STMicroelectronics/cmsis_device_h5.git', + '62b2cb0fbfe10c5791ee469bbde7b397c2fea8f5', + 'stm32h5'], + 'hw/mcu/st/cmsis_device_l0': ['https://github.com/STMicroelectronics/cmsis_device_l0.git', '06748ca1f93827befdb8b794402320d94d02004f', 'stm32l0'], @@ -140,6 +144,9 @@ deps_optional = { 'hw/mcu/st/stm32h7xx_hal_driver': ['https://github.com/STMicroelectronics/stm32h7xx_hal_driver.git', 'd8461b980b59b1625207d8c4f2ce0a9c2a7a3b04', 'stm32h7'], + 'hw/mcu/st/stm32h5xx_hal_driver': ['https://github.com/STMicroelectronics/stm32h5xx_hal_driver.git', + '2cf77de584196d619cec1b4586c3b9e2820a254e', + 'stm32h5'], 'hw/mcu/st/stm32l0xx_hal_driver': ['https://github.com/STMicroelectronics/stm32l0xx_hal_driver.git', 'fbdacaf6f8c82a4e1eb9bd74ba650b491e97e17b', 'stm32l0'], @@ -170,7 +177,7 @@ deps_optional = { 'lib/CMSIS_5': ['https://github.com/ARM-software/CMSIS_5.git', '20285262657d1b482d132d20d755c8c330d55c1f', 'imxrt kinetis_k32l2 kinetis_kl lpc51 lpc54 lpc55 mcx mm32 msp432e4 nrf ra saml2x' - 'stm32f0 stm32f1 stm32f2 stm32f3 stm32f4 stm32f7 stm32g0 stm32g4 ' + 'stm32f0 stm32f1 stm32f2 stm32f3 stm32f4 stm32f7 stm32g0 stm32g4 stm32h5' 'stm32h7 stm32l0 stm32l1 stm32l4 stm32l5 stm32u5 stm32wb'], 'lib/sct_neopixel': ['https://github.com/gsteiert/sct_neopixel.git', 'e73e04ca63495672d955f9268e003cffe168fcd8', -- cgit v1.3.1 From f3d713ac7336913a68326eae5a7e146ec2cd22c3 Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Tue, 12 Dec 2023 22:35:05 +0100 Subject: Fix CI & typo. --- hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h | 2 +- hw/bsp/stm32h5/boards/stm32h573i-dk/board.h | 2 +- hw/bsp/stm32h5/family.mk | 4 ++-- src/common/tusb_mcu.h | 1 - src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 7 ++----- src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 4 ++-- tools/get_deps.py | 1 - 7 files changed, 8 insertions(+), 13 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h b/hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h index ae0820529..9ebaf73f0 100644 --- a/hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h +++ b/hw/bsp/stm32g0/boards/stm32g0b1nucleo/board.h @@ -2,7 +2,7 @@ * The MIT License (MIT) * * Copyright (c) 2020, Ha Thach (tinyusb.org) - * Copyright (c) 2034, HiFiPhile + * Copyright (c) 2023, HiFiPhile * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal diff --git a/hw/bsp/stm32h5/boards/stm32h573i-dk/board.h b/hw/bsp/stm32h5/boards/stm32h573i-dk/board.h index 01834f151..a8808e32b 100644 --- a/hw/bsp/stm32h5/boards/stm32h573i-dk/board.h +++ b/hw/bsp/stm32h5/boards/stm32h573i-dk/board.h @@ -2,7 +2,7 @@ * The MIT License (MIT) * * Copyright (c) 2020, Ha Thach (tinyusb.org) - * Copyright (c) 2034, HiFiPhile + * Copyright (c) 2023, HiFiPhile * * Permission is hereby granted, free of charge, to any person obtaining a copy * of this software and associated documentation files (the "Software"), to deal diff --git a/hw/bsp/stm32h5/family.mk b/hw/bsp/stm32h5/family.mk index e04e08d80..2fd95ecec 100644 --- a/hw/bsp/stm32h5/family.mk +++ b/hw/bsp/stm32h5/family.mk @@ -11,9 +11,9 @@ CPU_CORE ?= cortex-m33 # Compiler Flags # -------------- CFLAGS += \ - -DCFG_TUSB_MCU=OPT_MCU_STM32H5 + -DCFG_TUSB_MCU=OPT_MCU_STM32H5 -# workaround to fix a build issue due to a wrong define check in hal, this define must be removed as soon as the repo is fixed +# workaround to fix a build issue due to a wrong define check in hal, this define must be removed as soon as the repo is fixed CFLAGS += \ -D__ARMCC_VERSION=0 diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 9c4083031..e589c4c86 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -214,7 +214,6 @@ #define TUP_USBIP_FSDEV #define TUP_USBIP_FSDEV_STM32 #define TUP_DCD_ENDPOINT_MAX 8 - #elif TU_CHECK_MCU(OPT_MCU_STM32G4) // Device controller diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index b0a00b7ee..21cd3da26 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -357,11 +357,9 @@ void dcd_int_enable (uint8_t rhport) #else NVIC_EnableIRQ(USB_UCPD1_2_IRQn); #endif - - + #elif CFG_TUSB_MCU == OPT_MCU_STM32H5 NVIC_EnableIRQ(USB_DRD_FS_IRQn); - #elif CFG_TUSB_MCU == OPT_MCU_STM32WB NVIC_EnableIRQ(USB_HP_IRQn); @@ -419,10 +417,9 @@ void dcd_int_disable(uint8_t rhport) #else NVIC_DisableIRQ(USB_UCPD1_2_IRQn); #endif - + #elif CFG_TUSB_MCU == OPT_MCU_STM32H5 NVIC_DisableIRQ(USB_DRD_FS_IRQn); - #elif CFG_TUSB_MCU == OPT_MCU_STM32WB NVIC_DisableIRQ(USB_HP_IRQn); diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index 0db426e50..b71e4f498 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -137,8 +137,8 @@ #define USB_EPADDR_FIELD USB_CHEP_ADDR #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY #define USB_CNTR_FSUSP USB_CNTR_SUSPEN - - + + #elif CFG_TUSB_MCU == OPT_MCU_STM32WB #include "stm32wbxx.h" #define PMA_LENGTH (1024u) diff --git a/tools/get_deps.py b/tools/get_deps.py index cda4fc8da..38ff81412 100644 --- a/tools/get_deps.py +++ b/tools/get_deps.py @@ -98,7 +98,6 @@ deps_optional = { 'hw/mcu/st/cmsis_device_h5': ['https://github.com/STMicroelectronics/cmsis_device_h5.git', '62b2cb0fbfe10c5791ee469bbde7b397c2fea8f5', 'stm32h5'], - 'hw/mcu/st/cmsis_device_l0': ['https://github.com/STMicroelectronics/cmsis_device_l0.git', '06748ca1f93827befdb8b794402320d94d02004f', 'stm32l0'], -- cgit v1.3.1 From 7f84fe9bdad2b3d7e2fc48b7dedb8bbdf305bf57 Mon Sep 17 00:00:00 2001 From: Jerzy Kasenberg Date: Thu, 21 Dec 2023 08:48:59 +0100 Subject: dcd_nrf5x: Fix dcd_edpt_open for iso endpoint When ISO endpoint handling was introduced two lines that clear stall and data toggle bit were left unchanged and they were effective for ISO enadpoint as well. This is incorrect behavior since EPSTALL and DTOGGLE registers have only 3 bits for address. Leaving code that clears toggle bit results in endpoint 0 toggle bit being reset when iso endpoint (8) is opened. Now code that clears stall and toggle bit is applied to non-iso endpoint only as it was done before iso handling was introduced. --- src/portable/nordic/nrf5x/dcd_nrf5x.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'src/portable') diff --git a/src/portable/nordic/nrf5x/dcd_nrf5x.c b/src/portable/nordic/nrf5x/dcd_nrf5x.c index acc967bb3..4e702aed4 100644 --- a/src/portable/nordic/nrf5x/dcd_nrf5x.c +++ b/src/portable/nordic/nrf5x/dcd_nrf5x.c @@ -340,6 +340,9 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) NRF_USBD->INTENSET = TU_BIT(USBD_INTEN_ENDEPIN0_Pos + epnum); NRF_USBD->EPINEN |= TU_BIT(epnum); } + // clear stall and reset DataToggle + NRF_USBD->EPSTALL = (USBD_EPSTALL_STALL_UnStall << USBD_EPSTALL_STALL_Pos) | ep_addr; + NRF_USBD->DTOGGLE = (USBD_DTOGGLE_VALUE_Data0 << USBD_DTOGGLE_VALUE_Pos) | ep_addr; } else { @@ -375,10 +378,6 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) } } - // clear stall and reset DataToggle - NRF_USBD->EPSTALL = (USBD_EPSTALL_STALL_UnStall << USBD_EPSTALL_STALL_Pos) | ep_addr; - NRF_USBD->DTOGGLE = (USBD_DTOGGLE_VALUE_Data0 << USBD_DTOGGLE_VALUE_Pos) | ep_addr; - __ISB(); __DSB(); return true; -- cgit v1.3.1 From 551e47a464f55e1e36e2812e79902f4ef2955a17 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 26 Dec 2023 22:50:01 +0700 Subject: allow rp2040 to use max3421e as host controller - fix warnings build hcd max3421 with rp2040 - add tinyusb_host_max3421 target for rp2040 cmake, -DMAX3421_HOST=1 will enable this - add max3421 driver implementation for rp2040 family - update tusb_config for host to allow easy enable host selection for rp2040 (default/pio-usb/max3421) --- .idea/cmake.xml | 15 +-- examples/host/bare_api/src/tusb_config.h | 64 +++++----- examples/host/cdc_msc_hid/src/tusb_config.h | 64 +++++----- .../host/cdc_msc_hid_freertos/src/tusb_config.h | 64 +++++----- examples/host/hid_controller/src/tusb_config.h | 64 +++++----- examples/host/msc_file_explorer/src/tusb_config.h | 65 +++++----- hw/bsp/rp2040/board.h | 11 ++ hw/bsp/rp2040/family.c | 140 +++++++++++++++------ hw/bsp/rp2040/family.cmake | 22 +++- src/portable/analog/max3421/hcd_max3421.c | 36 +++--- src/portable/raspberrypi/rp2040/hcd_rp2040.c | 2 +- 11 files changed, 341 insertions(+), 206 deletions(-) (limited to 'src/portable') diff --git a/.idea/cmake.xml b/.idea/cmake.xml index d12e44789..d3917c1f7 100644 --- a/.idea/cmake.xml +++ b/.idea/cmake.xml @@ -2,16 +2,17 @@ - - - + + + + - + @@ -25,7 +26,7 @@ - + @@ -39,10 +40,10 @@ - - + + diff --git a/examples/host/bare_api/src/tusb_config.h b/examples/host/bare_api/src/tusb_config.h index ede9618d3..05ffbdf75 100644 --- a/examples/host/bare_api/src/tusb_config.h +++ b/examples/host/bare_api/src/tusb_config.h @@ -30,28 +30,8 @@ extern "C" { #endif -//--------------------------------------------------------------------+ -// Board Specific Configuration -//--------------------------------------------------------------------+ - -#if CFG_TUSB_MCU == OPT_MCU_RP2040 -// change to 1 if using pico-pio-usb as host controller for raspberry rp2040 -#define CFG_TUH_RPI_PIO_USB 0 -#define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB -#endif - -// RHPort number used for host can be defined by board.mk, default to port 0 -#ifndef BOARD_TUH_RHPORT -#define BOARD_TUH_RHPORT 0 -#endif - -// RHPort max operational speed can defined by board.mk -#ifndef BOARD_TUH_MAX_SPEED -#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED -#endif - //-------------------------------------------------------------------- -// COMMON CONFIGURATION +// Common Configuration //-------------------------------------------------------------------- // defined by compiler flags for flexibility @@ -67,12 +47,6 @@ #define CFG_TUSB_DEBUG 0 #endif -// Enable Host stack -#define CFG_TUH_ENABLED 1 - -// Default is max speed that hardware controller could support with on-chip PHY -#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED - /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put * into those specific section. @@ -85,11 +59,43 @@ #endif #ifndef CFG_TUH_MEM_ALIGN -#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#endif + +//-------------------------------------------------------------------- +// Host Configuration +//-------------------------------------------------------------------- + +// Enable Host stack +#define CFG_TUH_ENABLED 1 + +#if CFG_TUSB_MCU == OPT_MCU_RP2040 + // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller + // #define CFG_TUH_RPI_PIO_USB 1 // use max3421 as host controller + + // host roothub port is 1 if using either pio-usb or max3421 + #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) + #define BOARD_TUH_RHPORT 1 + #endif +#endif + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED + +//------------------------- Board Specific -------------------------- + +// RHPort number used for host can be defined by board.mk, default to port 0 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif //-------------------------------------------------------------------- -// CONFIGURATION +// Driver Configuration //-------------------------------------------------------------------- // Size of buffer to hold descriptors and other data used for enumeration diff --git a/examples/host/cdc_msc_hid/src/tusb_config.h b/examples/host/cdc_msc_hid/src/tusb_config.h index a53000a11..61abb85eb 100644 --- a/examples/host/cdc_msc_hid/src/tusb_config.h +++ b/examples/host/cdc_msc_hid/src/tusb_config.h @@ -30,28 +30,8 @@ extern "C" { #endif -//--------------------------------------------------------------------+ -// Board Specific Configuration -//--------------------------------------------------------------------+ - -#if CFG_TUSB_MCU == OPT_MCU_RP2040 - // change to 1 if using pico-pio-usb as host controller for raspberry rp2040 - #define CFG_TUH_RPI_PIO_USB 0 - #define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB -#endif - -// RHPort number used for host can be defined by board.mk, default to port 0 -#ifndef BOARD_TUH_RHPORT -#define BOARD_TUH_RHPORT 0 -#endif - -// RHPort max operational speed can defined by board.mk -#ifndef BOARD_TUH_MAX_SPEED -#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED -#endif - //-------------------------------------------------------------------- -// COMMON CONFIGURATION +// Common Configuration //-------------------------------------------------------------------- // defined by compiler flags for flexibility @@ -67,12 +47,6 @@ #define CFG_TUSB_DEBUG 0 #endif -// Enable Host stack -#define CFG_TUH_ENABLED 1 - -// Default is max speed that hardware controller could support with on-chip PHY -#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED - /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put * into those specific section. @@ -85,11 +59,43 @@ #endif #ifndef CFG_TUH_MEM_ALIGN -#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#endif + +//-------------------------------------------------------------------- +// Host Configuration +//-------------------------------------------------------------------- + +// Enable Host stack +#define CFG_TUH_ENABLED 1 + +#if CFG_TUSB_MCU == OPT_MCU_RP2040 + // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller + // #define CFG_TUH_RPI_PIO_USB 1 // use max3421 as host controller + + // host roothub port is 1 if using either pio-usb or max3421 + #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) + #define BOARD_TUH_RHPORT 1 + #endif +#endif + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED + +//------------------------- Board Specific -------------------------- + +// RHPort number used for host can be defined by board.mk, default to port 0 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif //-------------------------------------------------------------------- -// CONFIGURATION +// Driver Configuration //-------------------------------------------------------------------- // Size of buffer to hold descriptors and other data used for enumeration diff --git a/examples/host/cdc_msc_hid_freertos/src/tusb_config.h b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h index ba23301ed..c661f47be 100644 --- a/examples/host/cdc_msc_hid_freertos/src/tusb_config.h +++ b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h @@ -30,28 +30,8 @@ extern "C" { #endif -//--------------------------------------------------------------------+ -// Board Specific Configuration -//--------------------------------------------------------------------+ - -#if CFG_TUSB_MCU == OPT_MCU_RP2040 - // change to 1 if using pico-pio-usb as host controller for raspberry rp2040 - #define CFG_TUH_RPI_PIO_USB 0 - #define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB -#endif - -// RHPort number used for host can be defined by board.mk, default to port 0 -#ifndef BOARD_TUH_RHPORT -#define BOARD_TUH_RHPORT 0 -#endif - -// RHPort max operational speed can defined by board.mk -#ifndef BOARD_TUH_MAX_SPEED -#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED -#endif - //-------------------------------------------------------------------- -// COMMON CONFIGURATION +// Common Configuration //-------------------------------------------------------------------- // defined by compiler flags for flexibility @@ -72,12 +52,6 @@ #define CFG_TUSB_DEBUG 0 #endif -// Enable Host stack -#define CFG_TUH_ENABLED 1 - -// Default is max speed that hardware controller could support with on-chip PHY -#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED - /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put * into those specific section. @@ -90,11 +64,43 @@ #endif #ifndef CFG_TUH_MEM_ALIGN -#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#endif + +//-------------------------------------------------------------------- +// Host Configuration +//-------------------------------------------------------------------- + +// Enable Host stack +#define CFG_TUH_ENABLED 1 + +#if CFG_TUSB_MCU == OPT_MCU_RP2040 + // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller + // #define CFG_TUH_RPI_PIO_USB 1 // use max3421 as host controller + + // host roothub port is 1 if using either pio-usb or max3421 + #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) + #define BOARD_TUH_RHPORT 1 + #endif +#endif + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED + +//------------------------- Board Specific -------------------------- + +// RHPort number used for host can be defined by board.mk, default to port 0 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif //-------------------------------------------------------------------- -// CONFIGURATION +// Driver Configuration //-------------------------------------------------------------------- // Size of buffer to hold descriptors and other data used for enumeration diff --git a/examples/host/hid_controller/src/tusb_config.h b/examples/host/hid_controller/src/tusb_config.h index d37fc02d2..8ddaddda7 100644 --- a/examples/host/hid_controller/src/tusb_config.h +++ b/examples/host/hid_controller/src/tusb_config.h @@ -30,28 +30,8 @@ extern "C" { #endif -//--------------------------------------------------------------------+ -// Board Specific Configuration -//--------------------------------------------------------------------+ - - #if CFG_TUSB_MCU == OPT_MCU_RP2040 -// change to 1 if using pico-pio-usb as host controller for raspberry rp2040 -#define CFG_TUH_RPI_PIO_USB 0 -#define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB -#endif - -// RHPort number used for host can be defined by board.mk, default to port 0 -#ifndef BOARD_TUH_RHPORT -#define BOARD_TUH_RHPORT 0 -#endif - -// RHPort max operational speed can defined by board.mk -#ifndef BOARD_TUH_MAX_SPEED -#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED -#endif - //-------------------------------------------------------------------- -// COMMON CONFIGURATION +// Common Configuration //-------------------------------------------------------------------- // defined by compiler flags for flexibility @@ -67,12 +47,6 @@ #define CFG_TUSB_DEBUG 0 #endif -// Enable Host stack -#define CFG_TUH_ENABLED 1 - -// Default is max speed that hardware controller could support with on-chip PHY -#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED - /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put * into those specific section. @@ -85,11 +59,43 @@ #endif #ifndef CFG_TUH_MEM_ALIGN -#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#endif + +//-------------------------------------------------------------------- +// Host Configuration +//-------------------------------------------------------------------- + +// Enable Host stack +#define CFG_TUH_ENABLED 1 + +#if CFG_TUSB_MCU == OPT_MCU_RP2040 + // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller + // #define CFG_TUH_RPI_PIO_USB 1 // use max3421 as host controller + + // host roothub port is 1 if using either pio-usb or max3421 + #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) + #define BOARD_TUH_RHPORT 1 + #endif +#endif + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED + +//------------------------- Board Specific -------------------------- + +// RHPort number used for host can be defined by board.mk, default to port 0 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif //-------------------------------------------------------------------- -// CONFIGURATION +// Driver Configuration //-------------------------------------------------------------------- // Size of buffer to hold descriptors and other data used for enumeration diff --git a/examples/host/msc_file_explorer/src/tusb_config.h b/examples/host/msc_file_explorer/src/tusb_config.h index b4ccd8223..1703761a4 100644 --- a/examples/host/msc_file_explorer/src/tusb_config.h +++ b/examples/host/msc_file_explorer/src/tusb_config.h @@ -30,29 +30,8 @@ extern "C" { #endif -//--------------------------------------------------------------------+ -// Board Specific Configuration -//--------------------------------------------------------------------+ - -#if CFG_TUSB_MCU == OPT_MCU_RP2040 - // change to 1 if using pico-pio-usb as host controller for raspberry rp2040 - #define CFG_TUH_RPI_PIO_USB 0 - #define BOARD_TUH_RHPORT CFG_TUH_RPI_PIO_USB -#endif - - -// RHPort number used for host can be defined by board.mk, default to port 0 -#ifndef BOARD_TUH_RHPORT -#define BOARD_TUH_RHPORT 0 -#endif - -// RHPort max operational speed can defined by board.mk -#ifndef BOARD_TUH_MAX_SPEED -#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED -#endif - //-------------------------------------------------------------------- -// COMMON CONFIGURATION +// Common Configuration //-------------------------------------------------------------------- // defined by compiler flags for flexibility @@ -68,12 +47,6 @@ #define CFG_TUSB_DEBUG 0 #endif -// Enable Host stack -#define CFG_TUH_ENABLED 1 - -// Default is max speed that hardware controller could support with on-chip PHY -#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED - /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment. * Tinyusb use follows macros to declare transferring memory so that they can be put * into those specific section. @@ -86,11 +59,43 @@ #endif #ifndef CFG_TUH_MEM_ALIGN -#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#define CFG_TUH_MEM_ALIGN __attribute__ ((aligned(4))) +#endif + +//-------------------------------------------------------------------- +// Host Configuration +//-------------------------------------------------------------------- + +// Enable Host stack +#define CFG_TUH_ENABLED 1 + +#if CFG_TUSB_MCU == OPT_MCU_RP2040 + // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller + // #define CFG_TUH_RPI_PIO_USB 1 // use max3421 as host controller + + // host roothub port is 1 if using either pio-usb or max3421 + #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) + #define BOARD_TUH_RHPORT 1 + #endif +#endif + +// Default is max speed that hardware controller could support with on-chip PHY +#define CFG_TUH_MAX_SPEED BOARD_TUH_MAX_SPEED + +//------------------------- Board Specific -------------------------- + +// RHPort number used for host can be defined by board.mk, default to port 0 +#ifndef BOARD_TUH_RHPORT +#define BOARD_TUH_RHPORT 0 +#endif + +// RHPort max operational speed can defined by board.mk +#ifndef BOARD_TUH_MAX_SPEED +#define BOARD_TUH_MAX_SPEED OPT_MODE_DEFAULT_SPEED #endif //-------------------------------------------------------------------- -// CONFIGURATION +// Driver Configuration //-------------------------------------------------------------------- // Size of buffer to hold descriptors and other data used for enumeration diff --git a/hw/bsp/rp2040/board.h b/hw/bsp/rp2040/board.h index 063c9580e..3849894ce 100644 --- a/hw/bsp/rp2040/board.h +++ b/hw/bsp/rp2040/board.h @@ -74,6 +74,17 @@ #define PICO_DEFAULT_PIO_USB_VBUSEN_STATE 1 #endif +//-------------------------------------------------------------------- +// USB Host MAX3421E +//-------------------------------------------------------------------- + +#define MAX3421_SPI PICO_DEFAULT_SPI_INSTANCE +#define MAX3421_SCK_PIN PICO_DEFAULT_SPI_SCK_PIN +#define MAX3421_MOSI_PIN PICO_DEFAULT_SPI_TX_PIN +#define MAX3421_MISO_PIN PICO_DEFAULT_SPI_RX_PIN +#define MAX3421_CS_PIN 10 +#define MAX3421_INTR_PIN 9 + #ifdef __cplusplus } #endif diff --git a/hw/bsp/rp2040/family.c b/hw/bsp/rp2040/family.c index 5ac104688..cffb632f3 100644 --- a/hw/bsp/rp2040/family.c +++ b/hw/bsp/rp2040/family.c @@ -37,10 +37,19 @@ #include "bsp/board_api.h" #include "board.h" +#ifdef UART_DEV +static uart_inst_t *uart_inst; +#endif + #if CFG_TUH_RPI_PIO_USB || CFG_TUD_RPI_PIO_USB #include "pio_usb.h" #endif +#if CFG_TUH_ENABLED && CFG_TUH_MAX3421 +#include "hardware/spi.h" +static void max3421_init(void); +#endif + #ifdef BUTTON_BOOTSEL // This example blinks the Picoboard LED when the BOOTSEL button is pressed. // @@ -53,73 +62,66 @@ // This doesn't work if others are trying to access flash at the same time, // e.g. XIP streamer, or the other core. bool __no_inline_not_in_flash_func(get_bootsel_button)(void) { - const uint CS_PIN_INDEX = 1; + const uint CS_PIN_INDEX = 1; - // Must disable interrupts, as interrupt handlers may be in flash, and we - // are about to temporarily disable flash access! - uint32_t flags = save_and_disable_interrupts(); + // Must disable interrupts, as interrupt handlers may be in flash, and we + // are about to temporarily disable flash access! + uint32_t flags = save_and_disable_interrupts(); - // Set chip select to Hi-Z - hw_write_masked(&ioqspi_hw->io[CS_PIN_INDEX].ctrl, - GPIO_OVERRIDE_LOW << IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_LSB, - IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_BITS); + // Set chip select to Hi-Z + hw_write_masked(&ioqspi_hw->io[CS_PIN_INDEX].ctrl, + GPIO_OVERRIDE_LOW << IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_LSB, + IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_BITS); - // Note we can't call into any sleep functions in flash right now - for (volatile int i = 0; i < 1000; ++i); + // Note we can't call into any sleep functions in flash right now + for (volatile int i = 0; i < 1000; ++i); - // The HI GPIO registers in SIO can observe and control the 6 QSPI pins. - // Note the button pulls the pin *low* when pressed. - bool button_state = (sio_hw->gpio_hi_in & (1u << CS_PIN_INDEX)); + // The HI GPIO registers in SIO can observe and control the 6 QSPI pins. + // Note the button pulls the pin *low* when pressed. + bool button_state = (sio_hw->gpio_hi_in & (1u << CS_PIN_INDEX)); - // Need to restore the state of chip select, else we are going to have a - // bad time when we return to code in flash! - hw_write_masked(&ioqspi_hw->io[CS_PIN_INDEX].ctrl, - GPIO_OVERRIDE_NORMAL << IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_LSB, - IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_BITS); + // Need to restore the state of chip select, else we are going to have a + // bad time when we return to code in flash! + hw_write_masked(&ioqspi_hw->io[CS_PIN_INDEX].ctrl, + GPIO_OVERRIDE_NORMAL << IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_LSB, + IO_QSPI_GPIO_QSPI_SS_CTRL_OEOVER_BITS); - restore_interrupts(flags); + restore_interrupts(flags); - return button_state; + return button_state; } #endif //------------- Segger RTT retarget -------------// #if defined(LOGGER_RTT) - // Logging with RTT // - If RTT Control Block is not found by 'Auto Detection` try to use 'Search Range` with '0x20000000 0x10000' // - SWD speed is rather slow around 1000Khz - #include "pico/stdio/driver.h" #include "SEGGER_RTT.h" -static void stdio_rtt_write (const char *buf, int length) -{ +static void stdio_rtt_write (const char *buf, int length) { SEGGER_RTT_Write(0, buf, (unsigned) length); } -static int stdio_rtt_read (char *buf, int len) -{ +static int stdio_rtt_read (char *buf, int len) { return (int) SEGGER_RTT_Read(0, buf, (unsigned) len); } -static stdio_driver_t stdio_rtt = -{ +static stdio_driver_t stdio_rtt = { .out_chars = stdio_rtt_write, .out_flush = NULL, .in_chars = stdio_rtt_read }; -void stdio_rtt_init(void) -{ +void stdio_rtt_init(void) { stdio_set_driver_enabled(&stdio_rtt, true); } - #endif -#ifdef UART_DEV -static uart_inst_t *uart_inst; -#endif +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ void board_init(void) { @@ -165,7 +167,9 @@ void board_init(void) #endif #if CFG_TUH_ENABLED - // set portfunc to host !!! + #if CFG_TUH_MAX3421 + max3421_init(); + #endif #endif #if !CFG_TUD_ENABLED && !CFG_TUH_ENABLED @@ -242,3 +246,69 @@ int board_getchar(void) { // rp2040 implementation will install appropriate handler when initializing // tinyusb. There is no need to forward IRQ from application //--------------------------------------------------------------------+ + +//--------------------------------------------------------------------+ +// API: SPI transfer with MAX3421E, must be implemented by application +//--------------------------------------------------------------------+ +#if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 + +void max3421_int_handler(uint gpio, uint32_t event_mask) { + if (!(gpio == MAX3421_INTR_PIN && event_mask & GPIO_IRQ_EDGE_FALL)) return; + tuh_int_handler(BOARD_TUH_RHPORT, true); +} + +static void max3421_init(void) { + // CS pin + gpio_init(MAX3421_CS_PIN); + gpio_set_dir(MAX3421_CS_PIN, GPIO_OUT); + gpio_put(MAX3421_CS_PIN, true); + + // Interrupt pin + gpio_init(MAX3421_INTR_PIN); + gpio_set_dir(MAX3421_INTR_PIN, GPIO_IN); + gpio_pull_up(MAX3421_INTR_PIN); + gpio_set_irq_enabled_with_callback(MAX3421_INTR_PIN, GPIO_IRQ_EDGE_FALL, true, max3421_int_handler); + + // SPI init + spi_init(MAX3421_SPI, 4*1000000ul); + gpio_set_function(MAX3421_SCK_PIN, GPIO_FUNC_SPI); + gpio_set_function(MAX3421_MOSI_PIN, GPIO_FUNC_SPI); + gpio_set_function(MAX3421_MISO_PIN, GPIO_FUNC_SPI); + spi_set_format(MAX3421_SPI, 8, SPI_CPOL_0, SPI_CPHA_0, SPI_MSB_FIRST); +} + +//// API to enable/disable MAX3421 INTR pin interrupt +void tuh_max3421_int_api(uint8_t rhport, bool enabled) { + (void) rhport; + irq_set_enabled(IO_IRQ_BANK0, enabled); +} + +// API to control MAX3421 SPI CS +void tuh_max3421_spi_cs_api(uint8_t rhport, bool active) { + (void) rhport; + gpio_put(MAX3421_CS_PIN, !active); +} + +// API to transfer data with MAX3421 SPI +// Either tx_buf or rx_buf can be NULL, which means transfer is write or read only +bool tuh_max3421_spi_xfer_api(uint8_t rhport, uint8_t const* tx_buf, uint8_t* rx_buf, size_t xfer_bytes) { + (void) rhport; + + if (tx_buf == NULL && rx_buf == NULL) { + return false; + } + + int ret; + + if (tx_buf == NULL) { + ret = spi_read_blocking(MAX3421_SPI, 0, rx_buf, xfer_bytes); + }else if (rx_buf == NULL) { + ret = spi_write_blocking(MAX3421_SPI, tx_buf, xfer_bytes); + }else { + ret = spi_write_read_blocking(spi0, tx_buf, rx_buf, xfer_bytes); + } + + return ret == (int) xfer_bytes; +} + +#endif diff --git a/hw/bsp/rp2040/family.cmake b/hw/bsp/rp2040/family.cmake index 77d8029d9..ec40806fd 100644 --- a/hw/bsp/rp2040/family.cmake +++ b/hw/bsp/rp2040/family.cmake @@ -103,6 +103,20 @@ target_compile_definitions(tinyusb_host_base INTERFACE RP2040_USB_HOST_MODE=1 ) +#------------------------------------ +# Host MAX3421 +#------------------------------------ +add_library(tinyusb_host_max3421 INTERFACE) +target_sources(tinyusb_host_max3421 INTERFACE + ${TOP}/src/portable/analog/max3421/hcd_max3421.c + ) +target_compile_definitions(tinyusb_host_max3421 INTERFACE + CFG_TUH_MAX3421=1 + ) +target_link_libraries(tinyusb_host_max3421 INTERFACE + hardware_spi + ) + #------------------------------------ # BSP & Additions #------------------------------------ @@ -126,7 +140,7 @@ target_compile_definitions(tinyusb_additions INTERFACE if(LOGGER STREQUAL "RTT" OR LOGGER STREQUAL "rtt") target_compile_definitions(tinyusb_additions INTERFACE LOGGER_RTT - SEGGER_RTT_MODE_DEFAULT=SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL + #SEGGER_RTT_MODE_DEFAULT=SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL ) target_sources(tinyusb_additions INTERFACE @@ -186,6 +200,7 @@ function(family_add_pico_pio_usb TARGET) target_link_libraries(${TARGET} PUBLIC tinyusb_pico_pio_usb) endfunction() + # since Pico-PIO_USB compiler support may lag, and change from version to version, add a function that pico-sdk/pico-examples # can check (if present) in case the user has updated their TinyUSB function(is_compiler_supported_by_pico_pio_usb OUTVAR) @@ -209,6 +224,11 @@ function(family_configure_host_example TARGET RTOS) family_add_pico_pio_usb(${PROJECT}) endif() endif() + + # for max3421 host + if (MAX3421_HOST STREQUAL "1") + target_link_libraries(${TARGET} PUBLIC tinyusb_host_max3421) + endif() endfunction() diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 051b7eaa8..cc4799dd6 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -171,6 +171,8 @@ enum { //--------------------------------------------------------------------+ typedef struct { + uint8_t daddr; + struct TU_ATTR_PACKED { uint8_t ep_dir : 1; uint8_t is_iso : 1; @@ -179,17 +181,19 @@ typedef struct { uint8_t xfer_pending : 1; uint8_t xfer_complete : 1; }; + struct TU_ATTR_PACKED { - uint8_t daddr : 4; uint8_t ep_num : 4; + uint16_t packet_size : 12; }; - uint16_t packet_size; uint16_t total_len; uint16_t xferred_len; uint8_t* buf; } max3421_ep_t; +TU_VERIFY_STATIC(sizeof(max3421_ep_t) == 12, "size is not correct"); + typedef struct { // cached register uint8_t sndbc; @@ -320,7 +324,7 @@ static void fifo_read(uint8_t rhport, uint8_t * buffer, uint16_t len, bool in_is static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr) { reg_write(rhport, HIRQ_ADDR, data, in_isr); // HIRQ write 1 is clear - _hcd_data.hirq &= ~data; + _hcd_data.hirq &= (uint8_t) ~data; } static inline void hien_write(uint8_t rhport, uint8_t data, bool in_isr) { @@ -390,7 +394,7 @@ static void free_ep(uint8_t daddr) { } static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { - size_t const idx = cur_ep - _hcd_data.ep; + size_t const idx = (size_t) (cur_ep - _hcd_data.ep); // starting from next endpoint for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { @@ -537,8 +541,8 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * e (void) rhport; (void) daddr; - uint8_t ep_num = tu_edpt_number(ep_desc->bEndpointAddress); - uint8_t ep_dir = tu_edpt_dir(ep_desc->bEndpointAddress); + uint8_t const ep_num = tu_edpt_number(ep_desc->bEndpointAddress); + tusb_dir_t const ep_dir = tu_edpt_dir(ep_desc->bEndpointAddress); max3421_ep_t * ep; if (daddr == 0 && ep_num == 0) { @@ -547,15 +551,15 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * e ep = allocate_ep(); TU_ASSERT(ep); ep->daddr = daddr; - ep->ep_num = ep_num; - ep->ep_dir = ep_dir; + ep->ep_num = (uint8_t) (ep_num & 0x0f); + ep->ep_dir = (ep_dir == TUSB_DIR_IN) ? 1 : 0; } if ( TUSB_XFER_ISOCHRONOUS == ep_desc->bmAttributes.xfer ) { ep->is_iso = 1; } - ep->packet_size = tu_edpt_packet_size(ep_desc); + ep->packet_size = (uint16_t) (tu_edpt_packet_size(ep_desc) & 0x7ff); return true; } @@ -577,7 +581,7 @@ void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { } sndbc_write(rhport, xact_len, in_isr); - uint8_t hxfr = ep->ep_num | HXFR_OUT_NIN | (ep->is_iso ? HXFR_ISO : 0); + uint8_t const hxfr = (uint8_t ) (ep->ep_num | HXFR_OUT_NIN | (ep->is_iso ? HXFR_ISO : 0)); hxfr_write(rhport, hxfr, in_isr); } @@ -590,7 +594,7 @@ void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { reg_write(rhport, HCTL_ADDR, hctl, in_isr); } - uint8_t hxfr = ep->ep_num | (ep->is_iso ? HXFR_ISO : 0); + uint8_t const hxfr = (uint8_t) (ep->ep_num | (ep->is_iso ? HXFR_ISO : 0)); hxfr_write(rhport, hxfr, in_isr); } @@ -623,13 +627,13 @@ TU_ATTR_ALWAYS_INLINE static inline void xact_inout(uint8_t rhport, max3421_ep_t // Submit a transfer, when complete hcd_event_xfer_complete() must be invoked bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buffer, uint16_t buflen) { uint8_t const ep_num = tu_edpt_number(ep_addr); - uint8_t const ep_dir = tu_edpt_dir(ep_addr); + uint8_t const ep_dir = (uint8_t) tu_edpt_dir(ep_addr); max3421_ep_t* ep = find_opened_ep(daddr, ep_num, ep_dir); TU_VERIFY(ep); // control transfer can switch direction - ep->ep_dir = ep_dir; + ep->ep_dir = ep_dir ? 1u : 0u; ep->buf = buffer; ep->total_len = buflen; @@ -748,9 +752,9 @@ static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t re // save data toggle if (ep->ep_dir) { - ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1 : 0; + ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1u : 0u; }else { - ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1 : 0; + ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1u : 0u; } ep->xfer_pending = 0; @@ -929,7 +933,7 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { } // clear all interrupt except SNDBAV_IRQ (never clear by us). Note RCVDAV_IRQ, HXFRDN_IRQ already clear while processing - hirq &= ~HIRQ_SNDBAV_IRQ; + hirq &= (uint8_t) ~HIRQ_SNDBAV_IRQ; if ( hirq ) { hirq_write(rhport, hirq, in_isr); } diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 4ed6d36bb..08aef9314 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -27,7 +27,7 @@ #include "tusb_option.h" -#if CFG_TUH_ENABLED && (CFG_TUSB_MCU == OPT_MCU_RP2040) && !CFG_TUH_RPI_PIO_USB +#if CFG_TUH_ENABLED && (CFG_TUSB_MCU == OPT_MCU_RP2040) && !CFG_TUH_RPI_PIO_USB && !CFG_TUH_MAX3421 #include "pico.h" #include "rp2040_usb.h" -- cgit v1.3.1 From 0d4b24e56cf11e79b46f88f0d8b8656c0444a149 Mon Sep 17 00:00:00 2001 From: Okarss <104319900+Okarss@users.noreply.github.com> Date: Sun, 7 Jan 2024 20:18:33 +0200 Subject: [STM32 FSDEV] Fix ISR race conditions --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 21cd3da26..5f7944d1f 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -673,13 +673,13 @@ void dcd_int_handler(uint8_t rhport) { /* Put SOF flag at the beginning of ISR in case to get least amount of jitter if it is used for timing purposes */ if(int_status & USB_ISTR_SOF) { - USB->ISTR &=~USB_ISTR_SOF; + USB->ISTR = ~USB_ISTR_SOF; dcd_event_sof(0, USB->FNR & USB_FNR_FN, true); } if(int_status & USB_ISTR_RESET) { // USBRST is start of reset. - USB->ISTR &=~USB_ISTR_RESET; + USB->ISTR = ~USB_ISTR_RESET; dcd_handle_bus_reset(); dcd_event_bus_reset(0, TUSB_SPEED_FULL, true); return; // Don't do the rest of the things here; perhaps they've been cleared? @@ -697,7 +697,7 @@ void dcd_int_handler(uint8_t rhport) { USB->CNTR &= ~USB_CNTR_LPMODE; USB->CNTR &= ~USB_CNTR_FSUSP; - USB->ISTR &=~USB_ISTR_WKUP; + USB->ISTR = ~USB_ISTR_WKUP; dcd_event_bus_signal(0, DCD_EVENT_RESUME, true); } @@ -711,7 +711,7 @@ void dcd_int_handler(uint8_t rhport) { USB->CNTR |= USB_CNTR_LPMODE; /* clear of the ISTR bit must be done after setting of CNTR_FSUSP */ - USB->ISTR &=~USB_ISTR_SUSP; + USB->ISTR = ~USB_ISTR_SUSP; dcd_event_bus_signal(0, DCD_EVENT_SUSPEND, true); } @@ -724,7 +724,7 @@ void dcd_int_handler(uint8_t rhport) { { remoteWakeCountdown--; } - USB->ISTR &=~USB_ISTR_ESOF; + USB->ISTR = ~USB_ISTR_ESOF; } } -- cgit v1.3.1 From e7e19f562765999ed76b25b93649e80d9652b088 Mon Sep 17 00:00:00 2001 From: Ryzee119 Date: Sun, 7 Jan 2024 08:30:33 +1030 Subject: [OHCI] Allow more than 16 devices --- src/portable/ohci/ohci.c | 16 +++++++++++++--- src/portable/ohci/ohci.h | 16 +++++++++++++--- 2 files changed, 26 insertions(+), 6 deletions(-) (limited to 'src/portable') diff --git a/src/portable/ohci/ohci.c b/src/portable/ohci/ohci.c index f978b0965..c7f4c04ad 100644 --- a/src/portable/ohci/ohci.c +++ b/src/portable/ohci/ohci.c @@ -157,6 +157,7 @@ static ohci_ed_t * const p_ed_head[] = static void ed_list_insert(ohci_ed_t * p_pre, ohci_ed_t * p_ed); static void ed_list_remove_by_addr(ohci_ed_t * p_head, uint8_t dev_addr); +static gtd_extra_data_t *gtd_get_extra_data(ohci_gtd_t const * const gtd); //--------------------------------------------------------------------+ // USBH-HCD API @@ -345,7 +346,7 @@ static void gtd_init(ohci_gtd_t *p_td, uint8_t *data_ptr, uint16_t total_bytes) tu_memclr(p_td, sizeof(ohci_gtd_t)); p_td->used = 1; - p_td->expected_bytes = total_bytes; + gtd_get_extra_data(p_td)->expected_bytes = total_bytes; p_td->buffer_rounding = 1; // less than queued length is not a error p_td->delay_interrupt = OHCI_INT_ON_COMPLETE_NO; @@ -610,6 +611,16 @@ static inline ohci_ed_t* gtd_get_ed(ohci_gtd_t const * const p_qtd) } } +static gtd_extra_data_t *gtd_get_extra_data(ohci_gtd_t const * const gtd) { + if ( gtd_is_control(gtd) ) + { + return &ohci_data.control[((intptr_t)gtd - (intptr_t)&ohci_data.control->gtd) / sizeof(ohci_data.control[0])].gtd_data; + }else + { + return &ohci_data.gtd_data[gtd - ohci_data.gtd_pool]; + } +} + static inline uint32_t gtd_xfer_byte_left(uint32_t buffer_end, uint32_t current_buffer) { // 5.2.9 OHCI sample code @@ -641,8 +652,7 @@ static void done_queue_isr(uint8_t hostid) if ( (qtd->delay_interrupt == OHCI_INT_ON_COMPLETE_YES) || (event != XFER_RESULT_SUCCESS) ) { ohci_ed_t * const ed = gtd_get_ed(qtd); - - uint32_t const xferred_bytes = qtd->expected_bytes - gtd_xfer_byte_left((uint32_t) qtd->buffer_end, (uint32_t) qtd->current_buffer_pointer); + uint32_t const xferred_bytes = gtd_get_extra_data(qtd)->expected_bytes - gtd_xfer_byte_left((uint32_t) qtd->buffer_end, (uint32_t) qtd->current_buffer_pointer); // NOTE Assuming the current list is BULK and there is no other EDs in the list has queued TDs. // When there is a error resulting this ED is halted, and this EP still has other queued TD diff --git a/src/portable/ohci/ohci.h b/src/portable/ohci/ohci.h index 2081ffabb..cb23396bc 100644 --- a/src/portable/ohci/ohci.h +++ b/src/portable/ohci/ohci.h @@ -45,6 +45,9 @@ enum { #define ED_MAX (CFG_TUH_DEVICE_MAX*CFG_TUH_ENDPOINT_MAX) #define GTD_MAX ED_MAX +// tinyUSB's OHCI implementation caps number of EDs to 8 bits +TU_VERIFY_STATIC (ED_MAX <= 256, "Reduce CFG_TUH_DEVICE_MAX or CFG_TUH_ENDPOINT_MAX"); + //--------------------------------------------------------------------+ // OHCI Data Structure //--------------------------------------------------------------------+ @@ -70,9 +73,8 @@ typedef struct TU_ATTR_ALIGNED(16) { // Word 0 uint32_t used : 1; - uint32_t index : 4; // endpoint index the td belongs to, or device address in case of control xfer - uint32_t expected_bytes : 13; // TODO available for hcd - + uint32_t index : 8; // endpoint index the gtd belongs to, or device address in case of control xfer + uint32_t : 9; // can be used uint32_t buffer_rounding : 1; uint32_t pid : 2; uint32_t delay_interrupt : 3; @@ -152,6 +154,12 @@ typedef struct TU_ATTR_ALIGNED(32) TU_VERIFY_STATIC( sizeof(ochi_itd_t) == 32, "size is not correct" ); +typedef struct +{ + uint16_t expected_bytes : 13; // can be up to 8192 bytes long so use 13 bits + uint16_t : 3; // can be used +} gtd_extra_data_t; + // structure with member alignment required from large to small typedef struct TU_ATTR_ALIGNED(256) { @@ -164,11 +172,13 @@ typedef struct TU_ATTR_ALIGNED(256) struct { ohci_ed_t ed; ohci_gtd_t gtd; + gtd_extra_data_t gtd_data; }control[CFG_TUH_DEVICE_MAX+CFG_TUH_HUB+1]; // ochi_itd_t itd[OHCI_MAX_ITD]; // itd requires alignment of 32 ohci_ed_t ed_pool[ED_MAX]; ohci_gtd_t gtd_pool[GTD_MAX]; + gtd_extra_data_t gtd_data[GTD_MAX]; // extra data needed by TDs that can't fit in the TD struct volatile uint16_t frame_number_hi; -- cgit v1.3.1 From 3bf6826451536f1afc6eb4e7f088ac65d9b8c707 Mon Sep 17 00:00:00 2001 From: Alex Voinea Date: Wed, 10 Jan 2024 10:27:21 +0100 Subject: Disable ULPI clock during sleep on stm32f7 when using internal phy --- src/portable/synopsys/dwc2/dwc2_stm32.h | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dwc2_stm32.h b/src/portable/synopsys/dwc2/dwc2_stm32.h index dd78ccd06..3237a50f6 100644 --- a/src/portable/synopsys/dwc2/dwc2_stm32.h +++ b/src/portable/synopsys/dwc2/dwc2_stm32.h @@ -149,7 +149,7 @@ static inline void dwc2_phy_init(dwc2_regs_t* dwc2, uint8_t hs_phy_type) { // https://community.st.com/t5/stm32cubemx-mcus/why-stm32h743-usb-fs-doesn-t-work-if-freertos-tickless-idle/m-p/349480#M18867 // H7 running on full-speed phy need to disable ULPI clock in sleep mode. // Otherwise, USB won't work when mcu executing WFI/WFE instruction i.e tick-less RTOS. - // Note: there may be other family that is affected by this, but only H7 is tested so far + // Note: there may be other family that is affected by this, but only H7 and F7 is tested so far #if defined(USB_OTG_FS_PERIPH_BASE) && defined(RCC_AHB1LPENR_USB2OTGFSULPILPEN) if ( USB_OTG_FS_PERIPH_BASE == (uint32_t) dwc2 ) { RCC->AHB1LPENR &= ~RCC_AHB1LPENR_USB2OTGFSULPILPEN; @@ -161,6 +161,13 @@ static inline void dwc2_phy_init(dwc2_regs_t* dwc2, uint8_t hs_phy_type) { RCC->AHB1LPENR &= ~RCC_AHB1LPENR_USB1OTGHSULPILPEN; } #endif + + #if defined(USB_OTG_HS_PERIPH_BASE) && defined(RCC_AHB1LPENR_OTGHSULPILPEN) + if ( USB_OTG_HS_PERIPH_BASE == (uint32_t) dwc2 ) { + RCC->AHB1LPENR &= ~RCC_AHB1LPENR_OTGHSULPILPEN; + } + #endif + } else { #if CFG_TUSB_MCU != OPT_MCU_STM32U5 // Disable FS PHY, TODO on U5A5 (dwc2 4.11a) 16th bit is 'Host CDP behavior enable' -- cgit v1.3.1 From 545821399b10243f84509a543ae8c6457e9da803 Mon Sep 17 00:00:00 2001 From: Okarss <104319900+Okarss@users.noreply.github.com> Date: Thu, 11 Jan 2024 00:59:39 +0200 Subject: [STM32 FSDEV] Introduce a typedef for bus access width --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 10 +++++----- src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 3 +++ 2 files changed, 8 insertions(+), 5 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 5f7944d1f..91f90352e 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -673,13 +673,13 @@ void dcd_int_handler(uint8_t rhport) { /* Put SOF flag at the beginning of ISR in case to get least amount of jitter if it is used for timing purposes */ if(int_status & USB_ISTR_SOF) { - USB->ISTR = ~USB_ISTR_SOF; + USB->ISTR = (fsdev_bus_t)~USB_ISTR_SOF; dcd_event_sof(0, USB->FNR & USB_FNR_FN, true); } if(int_status & USB_ISTR_RESET) { // USBRST is start of reset. - USB->ISTR = ~USB_ISTR_RESET; + USB->ISTR = (fsdev_bus_t)~USB_ISTR_RESET; dcd_handle_bus_reset(); dcd_event_bus_reset(0, TUSB_SPEED_FULL, true); return; // Don't do the rest of the things here; perhaps they've been cleared? @@ -697,7 +697,7 @@ void dcd_int_handler(uint8_t rhport) { USB->CNTR &= ~USB_CNTR_LPMODE; USB->CNTR &= ~USB_CNTR_FSUSP; - USB->ISTR = ~USB_ISTR_WKUP; + USB->ISTR = (fsdev_bus_t)~USB_ISTR_WKUP; dcd_event_bus_signal(0, DCD_EVENT_RESUME, true); } @@ -711,7 +711,7 @@ void dcd_int_handler(uint8_t rhport) { USB->CNTR |= USB_CNTR_LPMODE; /* clear of the ISTR bit must be done after setting of CNTR_FSUSP */ - USB->ISTR = ~USB_ISTR_SUSP; + USB->ISTR = (fsdev_bus_t)~USB_ISTR_SUSP; dcd_event_bus_signal(0, DCD_EVENT_SUSPEND, true); } @@ -724,7 +724,7 @@ void dcd_int_handler(uint8_t rhport) { { remoteWakeCountdown--; } - USB->ISTR = ~USB_ISTR_ESOF; + USB->ISTR = (fsdev_bus_t)~USB_ISTR_ESOF; } } diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index b71e4f498..d28eb0d9a 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -173,8 +173,11 @@ // For type-safety create a new macro for the volatile address of PMAADDR // The compiler should warn us if we cast it to a non-volatile type? #ifdef PMA_32BIT_ACCESS +typedef uint32_t fsdev_bus_t; static __IO uint32_t * const pma32 = (__IO uint32_t*)USB_PMAADDR; + #else +typedef uint16_t fsdev_bus_t; // Volatile is also needed to prevent the optimizer from changing access to 32-bit (as 32-bit access is forbidden) static __IO uint16_t * const pma = (__IO uint16_t*)USB_PMAADDR; -- cgit v1.3.1 From e68c6658c954d0c5daed2952d500c230b7dfb30d Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 11 Jan 2024 17:35:05 +0700 Subject: move gtd extra out of control struct to save sram also rename gtd_data to gtd_extra --- src/portable/ohci/ohci.c | 13 ++++++------- src/portable/ohci/ohci.h | 18 ++++++++---------- 2 files changed, 14 insertions(+), 17 deletions(-) (limited to 'src/portable') diff --git a/src/portable/ohci/ohci.c b/src/portable/ohci/ohci.c index c7f4c04ad..c59d4755e 100644 --- a/src/portable/ohci/ohci.c +++ b/src/portable/ohci/ohci.c @@ -612,12 +612,11 @@ static inline ohci_ed_t* gtd_get_ed(ohci_gtd_t const * const p_qtd) } static gtd_extra_data_t *gtd_get_extra_data(ohci_gtd_t const * const gtd) { - if ( gtd_is_control(gtd) ) - { - return &ohci_data.control[((intptr_t)gtd - (intptr_t)&ohci_data.control->gtd) / sizeof(ohci_data.control[0])].gtd_data; - }else - { - return &ohci_data.gtd_data[gtd - ohci_data.gtd_pool]; + if ( gtd_is_control(gtd) ) { + uint8_t idx = ((uintptr_t)gtd - (uintptr_t)&ohci_data.control->gtd) / sizeof(ohci_data.control[0]); + return &ohci_data.gtd_extra_control[idx]; + }else { + return &ohci_data.gtd_extra[gtd - ohci_data.gtd_pool]; } } @@ -661,7 +660,7 @@ static void done_queue_isr(uint8_t hostid) // --> HC will not process Control list (due to service ratio when Bulk list not empty) // To walk-around this, the halted ED will have TailP = HeadP (empty list condition), when clearing halt // the TailP must be set back to NULL for processing remaining TDs - if ((event != XFER_RESULT_SUCCESS)) + if (event != XFER_RESULT_SUCCESS) { ed->td_tail &= 0x0Ful; ed->td_tail |= tu_align16(ed->td_head.address); // mark halted EP as empty queue diff --git a/src/portable/ohci/ohci.h b/src/portable/ohci/ohci.h index cb23396bc..4feefd771 100644 --- a/src/portable/ohci/ohci.h +++ b/src/portable/ohci/ohci.h @@ -154,15 +154,12 @@ typedef struct TU_ATTR_ALIGNED(32) TU_VERIFY_STATIC( sizeof(ochi_itd_t) == 32, "size is not correct" ); -typedef struct -{ - uint16_t expected_bytes : 13; // can be up to 8192 bytes long so use 13 bits - uint16_t : 3; // can be used +typedef struct { + uint16_t expected_bytes; // up to 8192 bytes so max is 13 bits } gtd_extra_data_t; // structure with member alignment required from large to small -typedef struct TU_ATTR_ALIGNED(256) -{ +typedef struct TU_ATTR_ALIGNED(256) { ohci_hcca_t hcca; ohci_ed_t bulk_head_ed; // static bulk head (dummy) @@ -172,16 +169,17 @@ typedef struct TU_ATTR_ALIGNED(256) struct { ohci_ed_t ed; ohci_gtd_t gtd; - gtd_extra_data_t gtd_data; - }control[CFG_TUH_DEVICE_MAX+CFG_TUH_HUB+1]; + } control[CFG_TUH_DEVICE_MAX + CFG_TUH_HUB + 1]; // ochi_itd_t itd[OHCI_MAX_ITD]; // itd requires alignment of 32 ohci_ed_t ed_pool[ED_MAX]; ohci_gtd_t gtd_pool[GTD_MAX]; - gtd_extra_data_t gtd_data[GTD_MAX]; // extra data needed by TDs that can't fit in the TD struct - volatile uint16_t frame_number_hi; + // extra data needed by TDs that can't fit in the TD struct + gtd_extra_data_t gtd_extra_control[CFG_TUH_DEVICE_MAX + CFG_TUH_HUB + 1]; + gtd_extra_data_t gtd_extra[GTD_MAX]; + volatile uint16_t frame_number_hi; } ohci_data_t; //--------------------------------------------------------------------+ -- cgit v1.3.1 From 2d3d14891251baedfc965810c650615bdee128cf Mon Sep 17 00:00:00 2001 From: Okarss <104319900+Okarss@users.noreply.github.com> Date: Thu, 11 Jan 2024 21:02:14 +0200 Subject: [STM32 FSDEV] Align names for consistency --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 30 +++++----- .../st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 65 +++++++++++----------- 2 files changed, 48 insertions(+), 47 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 91f90352e..9c37f1f98 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -128,8 +128,8 @@ # define DCD_STM32_BTABLE_BASE 0U #endif -#ifndef DCD_STM32_BTABLE_LENGTH -# define DCD_STM32_BTABLE_LENGTH (PMA_LENGTH - DCD_STM32_BTABLE_BASE) +#ifndef DCD_STM32_BTABLE_SIZE +# define DCD_STM32_BTABLE_SIZE (FSDEV_PMA_SIZE - DCD_STM32_BTABLE_BASE) #endif /*************************************************** @@ -137,7 +137,7 @@ */ TU_VERIFY_STATIC((MAX_EP_COUNT) <= STFSDEV_EP_COUNT, "Only 8 endpoints supported on the hardware"); -TU_VERIFY_STATIC(((DCD_STM32_BTABLE_BASE) + (DCD_STM32_BTABLE_LENGTH))<=(PMA_LENGTH), "BTABLE does not fit in PMA RAM"); +TU_VERIFY_STATIC(((DCD_STM32_BTABLE_BASE) + (DCD_STM32_BTABLE_SIZE)) <= (FSDEV_PMA_SIZE), "BTABLE does not fit in PMA RAM"); TU_VERIFY_STATIC(((DCD_STM32_BTABLE_BASE) % 8) == 0, "BTABLE base must be aligned to 8 bytes"); //--------------------------------------------------------------------+ @@ -559,7 +559,7 @@ static void dcd_ep_ctr_rx_handler(uint32_t wIstr) // Must reset EP to NAK (in case it had been stalling) (though, maybe too late here) pcd_set_ep_rx_status(USB,0u,USB_EP_RX_NAK); pcd_set_ep_tx_status(USB,0u,USB_EP_TX_NAK); -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT dcd_event_setup_received(0, (uint8_t*)(USB_PMAADDR + pcd_get_ep_rx_address(USB, EPindex)), true); #else // The setup_received function uses memcpy, so this must first copy the setup data into @@ -786,7 +786,7 @@ static uint16_t dcd_pma_alloc(uint8_t ep_addr, uint16_t length) } // Ensure allocated buffer is aligned -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT length = (length + 3) & ~0x03; #else length = (length + 1) & ~0x01; @@ -798,7 +798,7 @@ static uint16_t dcd_pma_alloc(uint8_t ep_addr, uint16_t length) ep_buf_ptr = (uint16_t)(ep_buf_ptr + length); // increment buffer pointer // Verify no overflow - TU_ASSERT(ep_buf_ptr <= PMA_LENGTH, 0xFFFF); + TU_ASSERT(ep_buf_ptr <= FSDEV_PMA_SIZE, 0xFFFF); epXferCtl->pma_ptr = addr; epXferCtl->pma_alloc_size = length; @@ -1227,7 +1227,7 @@ void dcd_edpt_clear_stall (uint8_t rhport, uint8_t ep_addr) } } -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, uint16_t wNBytes) { const uint8_t* srcVal = src; @@ -1283,7 +1283,7 @@ static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, ui __IO uint16_t *pdwVal; srcVal = src; - pdwVal = &pma[PMA_STRIDE*(dst>>1)]; + pdwVal = &pma[FSDEV_PMA_STRIDE * (dst >> 1)]; while (n--) { @@ -1291,7 +1291,7 @@ static bool dcd_write_packet_memory(uint16_t dst, const void *__restrict src, ui srcVal++; temp2 = temp1 | ((uint16_t)(((uint16_t)(*srcVal)) << 8U)) ; *pdwVal = temp2; - pdwVal += PMA_STRIDE; + pdwVal += FSDEV_PMA_STRIDE; srcVal++; } @@ -1323,7 +1323,7 @@ static bool dcd_write_packet_memory_ff(tu_fifo_t * ff, uint16_t dst, uint16_t wN // We want to read from the FIFO and write it into the PMA, if LIN part is ODD and has WRAPPED part, // last lin byte will be combined with wrapped part // To ensure PMA is always access aligned (dst aligned to 16 or 32 bit) -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT if((cnt_lin & 0x03) && cnt_wrap) { // Copy first linear part @@ -1386,7 +1386,7 @@ static bool dcd_write_packet_memory_ff(tu_fifo_t * ff, uint16_t dst, uint16_t wN return true; } -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, uint16_t wNBytes) { uint8_t* dstVal = dst; @@ -1434,13 +1434,13 @@ static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, uint16_t __IO const uint16_t *pdwVal; uint32_t temp; - pdwVal = &pma[PMA_STRIDE*(src>>1)]; + pdwVal = &pma[FSDEV_PMA_STRIDE * (src >> 1)]; uint8_t *dstVal = (uint8_t*)dst; while (n--) { temp = *pdwVal; - pdwVal += PMA_STRIDE; + pdwVal += FSDEV_PMA_STRIDE; *dstVal++ = ((temp >> 0) & 0xFF); *dstVal++ = ((temp >> 8) & 0xFF); } @@ -1448,7 +1448,7 @@ static bool dcd_read_packet_memory(void *__restrict dst, uint16_t src, uint16_t if (wNBytes & 0x01) { temp = *pdwVal; - pdwVal += PMA_STRIDE; + pdwVal += FSDEV_PMA_STRIDE; *dstVal++ = ((temp >> 0) & 0xFF); } return true; @@ -1475,7 +1475,7 @@ static bool dcd_read_packet_memory_ff(tu_fifo_t * ff, uint16_t src, uint16_t wNB // We want to read from PMA and write it into the FIFO, if LIN part is ODD and has WRAPPED part, // last lin byte will be combined with wrapped part // To ensure PMA is always access aligned (src aligned to 16 or 32 bit) -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT if((cnt_lin & 0x03) && cnt_wrap) { // Copy first linear part diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index d28eb0d9a..3f4db985d 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -28,7 +28,7 @@ // This file contains source copied from ST's HAL, and thus should have their copyright statement. -// PMA_LENGTH is PMA buffer size in bytes. +// FSDEV_PMA_SIZE is PMA buffer size in bytes. // On 512-byte devices, access with a stride of two words (use every other 16-bit address) // On 1024-byte devices, access with a stride of one word (use every 16-bit address) @@ -37,7 +37,7 @@ #if CFG_TUSB_MCU == OPT_MCU_STM32F0 #include "stm32f0xx.h" - #define PMA_LENGTH (1024u) + #define FSDEV_PMA_SIZE (1024u) // F0x2 models are crystal-less // All have internal D+ pull-up // 070RB: 2 x 16 bits/word memory LPM Support, BCD Support @@ -45,7 +45,7 @@ #elif CFG_TUSB_MCU == OPT_MCU_STM32F1 #include "stm32f1xx.h" - #define PMA_LENGTH (512u) + #define FSDEV_PMA_SIZE (512u) // NO internal Pull-ups // *B, and *C: 2 x 16 bits/word @@ -56,7 +56,7 @@ defined(STM32F303xB) || defined(STM32F303xC) || \ defined(STM32F373xC) #include "stm32f3xx.h" - #define PMA_LENGTH (512u) + #define FSDEV_PMA_SIZE (512u) // NO internal Pull-ups // *B, and *C: 1 x 16 bits/word // PMA dedicated to USB (no sharing with CAN) @@ -65,27 +65,27 @@ defined(STM32F302xD) || defined(STM32F302xE) || \ defined(STM32F303xD) || defined(STM32F303xE) #include "stm32f3xx.h" - #define PMA_LENGTH (1024u) + #define FSDEV_PMA_SIZE (1024u) // NO internal Pull-ups // *6, *8, *D, and *E: 2 x 16 bits/word LPM Support // When CAN clock is enabled, USB can use first 768 bytes ONLY. #elif CFG_TUSB_MCU == OPT_MCU_STM32L0 #include "stm32l0xx.h" - #define PMA_LENGTH (1024u) + #define FSDEV_PMA_SIZE (1024u) #elif CFG_TUSB_MCU == OPT_MCU_STM32L1 #include "stm32l1xx.h" - #define PMA_LENGTH (512u) + #define FSDEV_PMA_SIZE (512u) #elif CFG_TUSB_MCU == OPT_MCU_STM32G4 #include "stm32g4xx.h" - #define PMA_LENGTH (1024u) + #define FSDEV_PMA_SIZE (1024u) #elif CFG_TUSB_MCU == OPT_MCU_STM32G0 #include "stm32g0xx.h" - #define PMA_32BIT_ACCESS - #define PMA_LENGTH (2048u) + #define FSDEV_BUS_32BIT + #define FSDEV_PMA_SIZE (2048u) #undef USB_PMAADDR #define USB_PMAADDR USB_DRD_PMAADDR #define USB_TypeDef USB_DRD_TypeDef @@ -112,8 +112,8 @@ #elif CFG_TUSB_MCU == OPT_MCU_STM32H5 #include "stm32h5xx.h" - #define PMA_32BIT_ACCESS - #define PMA_LENGTH (2048u) + #define FSDEV_BUS_32BIT + #define FSDEV_PMA_SIZE (2048u) #undef USB_PMAADDR #define USB_PMAADDR USB_DRD_PMAADDR #define USB_TypeDef USB_DRD_TypeDef @@ -141,18 +141,18 @@ #elif CFG_TUSB_MCU == OPT_MCU_STM32WB #include "stm32wbxx.h" - #define PMA_LENGTH (1024u) + #define FSDEV_PMA_SIZE (1024u) /* ST provided header has incorrect value */ #undef USB_PMAADDR #define USB_PMAADDR USB1_PMAADDR #elif CFG_TUSB_MCU == OPT_MCU_STM32L4 #include "stm32l4xx.h" - #define PMA_LENGTH (1024u) + #define FSDEV_PMA_SIZE (1024u) #elif CFG_TUSB_MCU == OPT_MCU_STM32L5 #include "stm32l5xx.h" - #define PMA_LENGTH (1024u) + #define FSDEV_PMA_SIZE (1024u) #ifndef USB_PMAADDR #define USB_PMAADDR (USB_BASE + (USB_PMAADDR_NS - USB_BASE_NS)) @@ -164,15 +164,16 @@ #endif // For purposes of accessing the packet -#if ((PMA_LENGTH) == 512u) - #define PMA_STRIDE (2u) -#elif ((PMA_LENGTH) == 1024u) - #define PMA_STRIDE (1u) +#if ((FSDEV_PMA_SIZE) == 512u) + #define FSDEV_PMA_STRIDE (2u) +#elif ((FSDEV_PMA_SIZE) == 1024u) + #define FSDEV_PMA_STRIDE (1u) #endif +// The fsdev_bus_t type can be used for both register and PMA access necessities // For type-safety create a new macro for the volatile address of PMAADDR // The compiler should warn us if we cast it to a non-volatile type? -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT typedef uint32_t fsdev_bus_t; static __IO uint32_t * const pma32 = (__IO uint32_t*)USB_PMAADDR; @@ -184,7 +185,7 @@ static __IO uint16_t * const pma = (__IO uint16_t*)USB_PMAADDR; TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t * pcd_btable_word_ptr(USB_TypeDef * USBx, size_t x) { size_t total_word_offset = (((USBx)->BTABLE)>>1) + x; - total_word_offset *= PMA_STRIDE; + total_word_offset *= FSDEV_PMA_STRIDE; return &(pma[total_word_offset]); } @@ -215,7 +216,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_aligned_buffer_size(uint16_t si /* SetENDPOINT */ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wRegValue) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; __O uint32_t *reg = (__O uint32_t *)(USB_DRD_BASE + bEpIdx*4); *reg = wRegValue; @@ -227,7 +228,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, ui /* GetENDPOINT */ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; __I uint32_t *reg = (__I uint32_t *)(USB_DRD_BASE + bEpIdx*4); #else @@ -282,7 +283,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_ep_ctr(USB_TypeDef * USBx, */ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; return (pma32[2*bEpIdx] & 0x03FF0000) >> 16; #else @@ -293,7 +294,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USB TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; return (pma32[2*bEpIdx + 1] & 0x03FF0000) >> 16; #else @@ -320,7 +321,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_address(USB_TypeDef * USBx, TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; return pma32[2*bEpIdx] & 0x0000FFFFu ; #else @@ -330,7 +331,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; return pma32[2*bEpIdx + 1] & 0x0000FFFFu; #else @@ -340,7 +341,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; pma32[2*bEpIdx] = (pma32[2*bEpIdx] & 0xFFFF0000u) | (addr & 0x0000FFFCu); #else @@ -350,7 +351,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USB TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & 0xFFFF0000u) | (addr & 0x0000FFFCu); #else @@ -360,7 +361,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USB TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; pma32[2*bEpIdx] = (pma32[2*bEpIdx] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); #else @@ -371,7 +372,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, u TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); #else @@ -383,7 +384,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, u TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_blsize_num_blocks(USB_TypeDef * USBx, uint32_t rxtx_idx, uint32_t blocksize, uint32_t numblocks) { /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ -#ifdef PMA_32BIT_ACCESS +#ifdef FSDEV_BUS_32BIT (void) USBx; pma32[rxtx_idx] = (pma32[rxtx_idx] & 0x0000FFFFu) | (blocksize << 31) | ((numblocks - blocksize) << 26); #else -- cgit v1.3.1 From 6c4a5292a6a59dec1b7f37be42725ea85205f3c9 Mon Sep 17 00:00:00 2001 From: Jerry Palacios Date: Wed, 7 Feb 2024 17:03:13 -0600 Subject: Back to original --- .github/workflows/build_aarch64.yml | 2 +- .github/workflows/build_arm.yml | 2 +- .github/workflows/build_esp.yml | 6 +- .github/workflows/build_iar.yml | 2 + .github/workflows/build_msp430.yml | 2 +- .github/workflows/build_renesas.yml | 2 +- .github/workflows/build_riscv.yml | 2 +- .github/workflows/build_win_mac.yml | 2 +- .github/workflows/cmake_arm.yml | 4 +- .github/workflows/pre-commit.yml | 2 +- examples/device/video_capture/src/CMakeLists.txt | 4 + examples/device/video_capture/src/images.h | 3 + examples/device/video_capture/src/main.c | 228 +++-- examples/device/video_capture/src/tusb_config.h | 12 +- .../device/video_capture/src/usb_descriptors.c | 450 +++++++--- .../device/video_capture/src/usb_descriptors.h | 87 +- examples/host/cdc_msc_hid/src/cdc_app.c | 76 +- examples/host/cdc_msc_hid/src/tusb_config.h | 1 + .../host/cdc_msc_hid_freertos/src/tusb_config.h | 1 + hw/bsp/board_api.h | 19 +- hw/bsp/espressif/boards/family.c | 30 +- hw/bsp/espressif/components/led_strip/CHANGELOG.md | 38 + .../espressif/components/led_strip/CMakeLists.txt | 27 +- hw/bsp/espressif/components/led_strip/LICENSE | 202 +++++ hw/bsp/espressif/components/led_strip/README.md | 97 +++ hw/bsp/espressif/components/led_strip/api.md | 454 ++++++++++ .../examples/led_strip_rmt_ws2812/CMakeLists.txt | 9 + .../examples/led_strip_rmt_ws2812/README.md | 31 + .../led_strip_rmt_ws2812/dependencies.lock | 15 + .../led_strip_rmt_ws2812/main/CMakeLists.txt | 2 + .../led_strip_rmt_ws2812/main/idf_component.yml | 5 + .../main/led_strip_rmt_ws2812_main.c | 75 ++ .../components/led_strip/idf_component.yml | 5 + .../components/led_strip/include/led_strip.h | 191 ++--- .../components/led_strip/include/led_strip_rmt.h | 53 ++ .../components/led_strip/include/led_strip_spi.h | 46 ++ .../components/led_strip/include/led_strip_types.h | 54 ++ .../led_strip/interface/led_strip_interface.h | 95 +++ .../components/led_strip/src/led_strip_api.c | 94 +++ .../components/led_strip/src/led_strip_rmt_dev.c | 164 ++++ .../led_strip/src/led_strip_rmt_dev_idf4.c | 194 +++++ .../led_strip/src/led_strip_rmt_encoder.c | 146 ++++ .../led_strip/src/led_strip_rmt_encoder.h | 38 + .../led_strip/src/led_strip_rmt_ws2812.c | 171 ---- .../components/led_strip/src/led_strip_spi_dev.c | 209 +++++ hw/bsp/family_support.cmake | 1 - hw/bsp/mcx/boards/bunny-brain/board.cmake | 21 - hw/bsp/mcx/boards/bunny-brain/board.h | 66 -- hw/bsp/mcx/boards/bunny-brain/board.mk | 11 - hw/bsp/mcx/boards/bunny-brain/clock_config.c | 338 -------- hw/bsp/mcx/boards/bunny-brain/clock_config.h | 177 ---- hw/bsp/mcx/boards/bunny-brain/pin_mux.c | 141 ---- hw/bsp/mcx/boards/bunny-brain/pin_mux.h | 51 -- hw/bsp/mcx/boards/frdm-mcxn947/board.cmake | 21 - hw/bsp/mcx/boards/frdm-mcxn947/board.h | 66 -- hw/bsp/mcx/boards/frdm-mcxn947/board.mk | 11 - hw/bsp/mcx/boards/frdm-mcxn947/clock_config.c | 338 -------- hw/bsp/mcx/boards/frdm-mcxn947/clock_config.h | 177 ---- hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.c | 143 ---- hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.h | 51 -- src/class/audio/audio_device.c | 2 +- src/class/cdc/cdc.h | 20 +- src/class/cdc/cdc_host.c | 916 ++++++++++++++++----- src/class/cdc/cdc_host.h | 13 +- src/class/cdc/serial/ch34x.h | 84 ++ src/class/hid/hid_host.c | 6 +- src/class/vendor/vendor_device.c | 8 +- src/class/video/video.h | 236 ++++-- src/class/video/video_device.c | 26 +- src/common/tusb_common.h | 1 + src/common/tusb_types.h | 157 ++-- src/portable/synopsys/dwc2/dcd_dwc2.c | 4 +- src/tusb_option.h | 17 + test/hil/hil_test.py | 11 +- 74 files changed, 3839 insertions(+), 2627 deletions(-) create mode 100644 examples/device/video_capture/src/CMakeLists.txt create mode 100644 hw/bsp/espressif/components/led_strip/CHANGELOG.md create mode 100644 hw/bsp/espressif/components/led_strip/LICENSE create mode 100644 hw/bsp/espressif/components/led_strip/README.md create mode 100644 hw/bsp/espressif/components/led_strip/api.md create mode 100644 hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/CMakeLists.txt create mode 100644 hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/README.md create mode 100644 hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/dependencies.lock create mode 100644 hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/CMakeLists.txt create mode 100644 hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/idf_component.yml create mode 100644 hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/led_strip_rmt_ws2812_main.c create mode 100644 hw/bsp/espressif/components/led_strip/idf_component.yml create mode 100644 hw/bsp/espressif/components/led_strip/include/led_strip_rmt.h create mode 100644 hw/bsp/espressif/components/led_strip/include/led_strip_spi.h create mode 100644 hw/bsp/espressif/components/led_strip/include/led_strip_types.h create mode 100644 hw/bsp/espressif/components/led_strip/interface/led_strip_interface.h create mode 100644 hw/bsp/espressif/components/led_strip/src/led_strip_api.c create mode 100644 hw/bsp/espressif/components/led_strip/src/led_strip_rmt_dev.c create mode 100644 hw/bsp/espressif/components/led_strip/src/led_strip_rmt_dev_idf4.c create mode 100644 hw/bsp/espressif/components/led_strip/src/led_strip_rmt_encoder.c create mode 100644 hw/bsp/espressif/components/led_strip/src/led_strip_rmt_encoder.h delete mode 100644 hw/bsp/espressif/components/led_strip/src/led_strip_rmt_ws2812.c create mode 100644 hw/bsp/espressif/components/led_strip/src/led_strip_spi_dev.c delete mode 100644 hw/bsp/mcx/boards/bunny-brain/board.cmake delete mode 100644 hw/bsp/mcx/boards/bunny-brain/board.h delete mode 100644 hw/bsp/mcx/boards/bunny-brain/board.mk delete mode 100644 hw/bsp/mcx/boards/bunny-brain/clock_config.c delete mode 100644 hw/bsp/mcx/boards/bunny-brain/clock_config.h delete mode 100644 hw/bsp/mcx/boards/bunny-brain/pin_mux.c delete mode 100644 hw/bsp/mcx/boards/bunny-brain/pin_mux.h delete mode 100644 hw/bsp/mcx/boards/frdm-mcxn947/board.cmake delete mode 100644 hw/bsp/mcx/boards/frdm-mcxn947/board.h delete mode 100644 hw/bsp/mcx/boards/frdm-mcxn947/board.mk delete mode 100644 hw/bsp/mcx/boards/frdm-mcxn947/clock_config.c delete mode 100644 hw/bsp/mcx/boards/frdm-mcxn947/clock_config.h delete mode 100644 hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.c delete mode 100644 hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.h create mode 100644 src/class/cdc/serial/ch34x.h (limited to 'src/portable') diff --git a/.github/workflows/build_aarch64.yml b/.github/workflows/build_aarch64.yml index 40fc8d63a..e5dbf9494 100644 --- a/.github/workflows/build_aarch64.yml +++ b/.github/workflows/build_aarch64.yml @@ -36,7 +36,7 @@ jobs: - 'broadcom_64bit' steps: - name: Setup Python - uses: actions/setup-python@v4 + uses: actions/setup-python@v5 with: python-version: '3.x' diff --git a/.github/workflows/build_arm.yml b/.github/workflows/build_arm.yml index 4127db5bf..9f3270c91 100644 --- a/.github/workflows/build_arm.yml +++ b/.github/workflows/build_arm.yml @@ -46,7 +46,7 @@ jobs: - 'tm4c123 xmc4000' steps: - name: Setup Python - uses: actions/setup-python@v4 + uses: actions/setup-python@v5 with: python-version: '3.x' diff --git a/.github/workflows/build_esp.yml b/.github/workflows/build_esp.yml index 33caa0edb..8fbdb31ff 100644 --- a/.github/workflows/build_esp.yml +++ b/.github/workflows/build_esp.yml @@ -8,6 +8,7 @@ on: - 'examples/**' - 'lib/**' - 'hw/**' + - 'test/hil/**' - '.github/workflows/build_esp.yml' pull_request: branches: [ master ] @@ -16,6 +17,7 @@ on: - 'examples/**' - 'lib/**' - 'hw/**' + - 'test/hil/**' - '.github/workflows/build_esp.yml' concurrency: @@ -35,7 +37,7 @@ jobs: - 'espressif_s3_devkitc' steps: - name: Setup Python - uses: actions/setup-python@v4 + uses: actions/setup-python@v5 with: python-version: '3.x' @@ -46,7 +48,7 @@ jobs: uses: actions/checkout@v4 - name: Build - run: docker run --rm -v $PWD:/project -w /project espressif/idf:latest python3 tools/build_esp32.py ${{ matrix.board }} + run: docker run --rm -v $PWD:/project -w /project espressif/idf:v5.1.1 python3 tools/build_esp32.py ${{ matrix.board }} - name: Upload Artifacts for Hardware Testing if: matrix.board == 'espressif_s3_devkitc' && github.repository_owner == 'hathach' diff --git a/.github/workflows/build_iar.yml b/.github/workflows/build_iar.yml index 9f2cc0351..a0a022ecc 100644 --- a/.github/workflows/build_iar.yml +++ b/.github/workflows/build_iar.yml @@ -9,6 +9,7 @@ on: - 'lib/**' - 'hw/**' - 'tools/get_deps.py' + - 'test/hil/**' - '.github/workflows/build_iar.yml' pull_request: branches: [ master ] @@ -18,6 +19,7 @@ on: - 'lib/**' - 'hw/**' - 'tools/get_deps.py' + - 'test/hil/**' - '.github/workflows/build_iar.yml' concurrency: diff --git a/.github/workflows/build_msp430.yml b/.github/workflows/build_msp430.yml index 296dbb766..f913df913 100644 --- a/.github/workflows/build_msp430.yml +++ b/.github/workflows/build_msp430.yml @@ -36,7 +36,7 @@ jobs: steps: - name: Setup Python - uses: actions/setup-python@v4 + uses: actions/setup-python@v5 with: python-version: '3.x' diff --git a/.github/workflows/build_renesas.yml b/.github/workflows/build_renesas.yml index 017a29eee..ec06c9426 100644 --- a/.github/workflows/build_renesas.yml +++ b/.github/workflows/build_renesas.yml @@ -35,7 +35,7 @@ jobs: - 'rx' steps: - name: Setup Python - uses: actions/setup-python@v4 + uses: actions/setup-python@v5 with: python-version: '3.x' diff --git a/.github/workflows/build_riscv.yml b/.github/workflows/build_riscv.yml index e030bb77f..e891a3a51 100644 --- a/.github/workflows/build_riscv.yml +++ b/.github/workflows/build_riscv.yml @@ -37,7 +37,7 @@ jobs: - 'gd32vf103' steps: - name: Setup Python - uses: actions/setup-python@v4 + uses: actions/setup-python@v5 with: python-version: '3.x' diff --git a/.github/workflows/build_win_mac.yml b/.github/workflows/build_win_mac.yml index 7fa1a6943..b33b5b593 100644 --- a/.github/workflows/build_win_mac.yml +++ b/.github/workflows/build_win_mac.yml @@ -35,7 +35,7 @@ jobs: steps: - name: Setup Python - uses: actions/setup-python@v4 + uses: actions/setup-python@v5 with: python-version: '3.x' diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index 8b87fef21..f97645ad1 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -8,6 +8,7 @@ on: - 'examples/**' - 'lib/**' - 'hw/**' + - 'test/hil/**' - 'tools/get_deps.py' - '.github/workflows/cmake_arm.yml' pull_request: @@ -17,6 +18,7 @@ on: - 'examples/**' - 'lib/**' - 'hw/**' + - 'test/hil/**' - 'tools/get_deps.py' - '.github/workflows/cmake_arm.yml' @@ -57,7 +59,7 @@ jobs: - 'stm32u5' steps: - name: Setup Python - uses: actions/setup-python@v4 + uses: actions/setup-python@v5 with: python-version: '3.x' diff --git a/.github/workflows/pre-commit.yml b/.github/workflows/pre-commit.yml index 2e9ae9264..e36259daa 100644 --- a/.github/workflows/pre-commit.yml +++ b/.github/workflows/pre-commit.yml @@ -15,7 +15,7 @@ jobs: runs-on: ubuntu-latest steps: - name: Setup Python - uses: actions/setup-python@v4 + uses: actions/setup-python@v5 with: python-version: '3.x' diff --git a/examples/device/video_capture/src/CMakeLists.txt b/examples/device/video_capture/src/CMakeLists.txt new file mode 100644 index 000000000..cef2b46ee --- /dev/null +++ b/examples/device/video_capture/src/CMakeLists.txt @@ -0,0 +1,4 @@ +# This file is for ESP-IDF only +idf_component_register(SRCS "main.c" "usb_descriptors.c" + INCLUDE_DIRS "." + REQUIRES boards tinyusb_src) diff --git a/examples/device/video_capture/src/images.h b/examples/device/video_capture/src/images.h index 784e7754c..ac372cb16 100644 --- a/examples/device/video_capture/src/images.h +++ b/examples/device/video_capture/src/images.h @@ -1,4 +1,5 @@ #if defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) +// uncopmressed frame static const unsigned char frame_buffer[128 * (96 + 1) * 2] = { /* 0 */ 0xeb, 0x80, 0xeb, 0x80, 0xeb, 0x80, 0xeb, 0x80, 0xeb, 0x80, 0xeb, 0x80, 0xeb, 0x80, 0xeb, 0x80, @@ -1650,8 +1651,10 @@ static const unsigned char frame_buffer[128 * (96 + 1) * 2] = { 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, 0x10, 0x80, }; + #else +// mpeg compressed data (not CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) #define color_bar_0_jpg_len 511 #define color_bar_1_jpg_len 512 #define color_bar_2_jpg_len 511 diff --git a/examples/device/video_capture/src/main.c b/examples/device/video_capture/src/main.c index 711d4710a..2a2b0961f 100644 --- a/examples/device/video_capture/src/main.c +++ b/examples/device/video_capture/src/main.c @@ -40,7 +40,7 @@ * - 1000 ms : device mounted * - 2500 ms : device is suspended */ -enum { +enum { BLINK_NOT_MOUNTED = 250, BLINK_MOUNTED = 1000, BLINK_SUSPENDED = 2500, @@ -48,14 +48,25 @@ enum { static uint32_t blink_interval_ms = BLINK_NOT_MOUNTED; -void led_blinking_task(void); -void video_task(void); +void led_blinking_task(void* param); +void usb_device_task(void *param); +void video_task(void* param); -/*------------- MAIN -------------*/ -int main(void) -{ +#if CFG_TUSB_OS == OPT_OS_FREERTOS +void freertos_init_task(void); +#endif + + +//--------------------------------------------------------------------+ +// Main +//--------------------------------------------------------------------+ +int main(void) { board_init(); + // If using FreeRTOS: create blinky, tinyusb device, video task +#if CFG_TUSB_OS == OPT_OS_FREERTOS + freertos_init_task(); +#else // init device stack on configured roothub port tud_init(BOARD_TUD_RHPORT); @@ -63,13 +74,12 @@ int main(void) board_init_after_tusb(); } - while (1) - { + while (1) { tud_task(); // tinyusb device task - led_blinking_task(); - - video_task(); + led_blinking_task(NULL); + video_task(NULL); } +#endif } //--------------------------------------------------------------------+ @@ -77,33 +87,28 @@ int main(void) //--------------------------------------------------------------------+ // Invoked when device is mounted -void tud_mount_cb(void) -{ +void tud_mount_cb(void) { blink_interval_ms = BLINK_MOUNTED; } // Invoked when device is unmounted -void tud_umount_cb(void) -{ +void tud_umount_cb(void) { blink_interval_ms = BLINK_NOT_MOUNTED; } // Invoked when usb bus is suspended // remote_wakeup_en : if host allow us to perform remote wakeup // Within 7ms, device must draw an average of current less than 2.5 mA from bus -void tud_suspend_cb(bool remote_wakeup_en) -{ +void tud_suspend_cb(bool remote_wakeup_en) { (void) remote_wakeup_en; blink_interval_ms = BLINK_SUSPENDED; } // Invoked when usb bus is resumed -void tud_resume_cb(void) -{ +void tud_resume_cb(void) { blink_interval_ms = tud_mounted() ? BLINK_MOUNTED : BLINK_NOT_MOUNTED; } - //--------------------------------------------------------------------+ // USB Video //--------------------------------------------------------------------+ @@ -111,11 +116,12 @@ static unsigned frame_num = 0; static unsigned tx_busy = 0; static unsigned interval_ms = 1000 / FRAME_RATE; -/* YUY2 frame buffer */ #ifdef CFG_EXAMPLE_VIDEO_READONLY +// For mcus that does not have enough SRAM for frame buffer, we use fixed frame data. +// To further reduce the size, we use MJPEG format instead of YUY2. #include "images.h" -# if !defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) +#if !defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) static struct { uint32_t size; uint8_t const *buffer; @@ -129,29 +135,30 @@ static struct { {color_bar_6_jpg_len, color_bar_6_jpg}, {color_bar_7_jpg_len, color_bar_7_jpg}, }; -# endif +#endif #else + +// YUY2 frame buffer static uint8_t frame_buffer[FRAME_WIDTH * FRAME_HEIGHT * 16 / 8]; -static void fill_color_bar(uint8_t *buffer, unsigned start_position) -{ - /* EBU color bars - * See also https://stackoverflow.com/questions/6939422 */ + +static void fill_color_bar(uint8_t* buffer, unsigned start_position) { + /* EBU color bars: https://stackoverflow.com/questions/6939422 */ static uint8_t const bar_color[8][4] = { - /* Y, U, Y, V */ - { 235, 128, 235, 128}, /* 100% White */ - { 219, 16, 219, 138}, /* Yellow */ - { 188, 154, 188, 16}, /* Cyan */ - { 173, 42, 173, 26}, /* Green */ - { 78, 214, 78, 230}, /* Magenta */ - { 63, 102, 63, 240}, /* Red */ - { 32, 240, 32, 118}, /* Blue */ - { 16, 128, 16, 128}, /* Black */ + /* Y, U, Y, V */ + { 235, 128, 235, 128}, /* 100% White */ + { 219, 16, 219, 138}, /* Yellow */ + { 188, 154, 188, 16}, /* Cyan */ + { 173, 42, 173, 26}, /* Green */ + { 78, 214, 78, 230}, /* Magenta */ + { 63, 102, 63, 240}, /* Red */ + { 32, 240, 32, 118}, /* Blue */ + { 16, 128, 16, 128}, /* Black */ }; - uint8_t *p; + uint8_t* p; /* Generate the 1st line */ - uint8_t *end = &buffer[FRAME_WIDTH * 2]; + uint8_t* end = &buffer[FRAME_WIDTH * 2]; unsigned idx = (FRAME_WIDTH / 2 - 1) - (start_position % (FRAME_WIDTH / 2)); p = &buffer[idx * 4]; for (unsigned i = 0; i < 8; ++i) { @@ -163,6 +170,7 @@ static void fill_color_bar(uint8_t *buffer, unsigned start_position) } } } + /* Duplicate the 1st line to the others */ p = &buffer[FRAME_WIDTH * 2]; for (unsigned i = 1; i < FRAME_HEIGHT; ++i) { @@ -170,32 +178,33 @@ static void fill_color_bar(uint8_t *buffer, unsigned start_position) p += FRAME_WIDTH * 2; } } + #endif -void video_task(void) -{ +void video_send_frame(void) { static unsigned start_ms = 0; static unsigned already_sent = 0; if (!tud_video_n_streaming(0, 0)) { - already_sent = 0; - frame_num = 0; + already_sent = 0; + frame_num = 0; return; } if (!already_sent) { already_sent = 1; + tx_busy = 1; start_ms = board_millis(); #ifdef CFG_EXAMPLE_VIDEO_READONLY -# if defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) + #if defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) tud_video_n_frame_xfer(0, 0, (void*)(uintptr_t)&frame_buffer[(frame_num % (FRAME_WIDTH / 2)) * 4], FRAME_WIDTH * FRAME_HEIGHT * 16/8); -# else + #else tud_video_n_frame_xfer(0, 0, (void*)(uintptr_t)frames[frame_num % 8].buffer, frames[frame_num % 8].size); -# endif + #endif #else fill_color_bar(frame_buffer, frame_num); - tud_video_n_frame_xfer(0, 0, (void*)frame_buffer, FRAME_WIDTH * FRAME_HEIGHT * 16/8); + tud_video_n_frame_xfer(0, 0, (void*) frame_buffer, FRAME_WIDTH * FRAME_HEIGHT * 16 / 8); #endif } @@ -203,49 +212,140 @@ void video_task(void) if (cur - start_ms < interval_ms) return; // not enough time if (tx_busy) return; start_ms += interval_ms; + tx_busy = 1; #ifdef CFG_EXAMPLE_VIDEO_READONLY -# if defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) + #if defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) tud_video_n_frame_xfer(0, 0, (void*)(uintptr_t)&frame_buffer[(frame_num % (FRAME_WIDTH / 2)) * 4], FRAME_WIDTH * FRAME_HEIGHT * 16/8); -# else + #else tud_video_n_frame_xfer(0, 0, (void*)(uintptr_t)frames[frame_num % 8].buffer, frames[frame_num % 8].size); -# endif + #endif #else fill_color_bar(frame_buffer, frame_num); - tud_video_n_frame_xfer(0, 0, (void*)frame_buffer, FRAME_WIDTH * FRAME_HEIGHT * 16/8); + tud_video_n_frame_xfer(0, 0, (void*) frame_buffer, FRAME_WIDTH * FRAME_HEIGHT * 16 / 8); #endif } -void tud_video_frame_xfer_complete_cb(uint_fast8_t ctl_idx, uint_fast8_t stm_idx) -{ - (void)ctl_idx; (void)stm_idx; + +void video_task(void* param) { + (void) param; + + while(1) { + video_send_frame(); + + #if CFG_TUSB_OS == OPT_OS_FREERTOS + vTaskDelay(interval_ms / portTICK_PERIOD_MS); + #else + return; + #endif + } +} + +void tud_video_frame_xfer_complete_cb(uint_fast8_t ctl_idx, uint_fast8_t stm_idx) { + (void) ctl_idx; + (void) stm_idx; tx_busy = 0; /* flip buffer */ ++frame_num; } int tud_video_commit_cb(uint_fast8_t ctl_idx, uint_fast8_t stm_idx, - video_probe_and_commit_control_t const *parameters) -{ - (void)ctl_idx; (void)stm_idx; + video_probe_and_commit_control_t const* parameters) { + (void) ctl_idx; + (void) stm_idx; /* convert unit to ms from 100 ns */ interval_ms = parameters->dwFrameInterval / 10000; return VIDEO_ERROR_NONE; } //--------------------------------------------------------------------+ -// BLINKING TASK +// Blinking Task //--------------------------------------------------------------------+ -void led_blinking_task(void) -{ +void led_blinking_task(void* param) { + (void) param; static uint32_t start_ms = 0; static bool led_state = false; - // Blink every interval ms - if ( board_millis() - start_ms < blink_interval_ms) return; // not enough time - start_ms += blink_interval_ms; + while (1) { + #if CFG_TUSB_OS == OPT_OS_FREERTOS + vTaskDelay(blink_interval_ms / portTICK_PERIOD_MS); + #else + if (board_millis() - start_ms < blink_interval_ms) return; // not enough time + #endif + + start_ms += blink_interval_ms; + board_led_write(led_state); + led_state = 1 - led_state; // toggle + } +} + +//--------------------------------------------------------------------+ +// FreeRTOS +//--------------------------------------------------------------------+ +#if CFG_TUSB_OS == OPT_OS_FREERTOS + +#define BLINKY_STACK_SIZE configMINIMAL_STACK_SIZE +#define VIDEO_STACK_SIZE (configMINIMAL_STACK_SIZE*4) + +#if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) + #define USBD_STACK_SIZE 4096 + int main(void); + void app_main(void) { + main(); + } +#else + // Increase stack size when debug log is enabled + #define USBD_STACK_SIZE (3*configMINIMAL_STACK_SIZE/2) * (CFG_TUSB_DEBUG ? 2 : 1) +#endif + +// static task +#if configSUPPORT_STATIC_ALLOCATION +StackType_t blinky_stack[BLINKY_STACK_SIZE]; +StaticTask_t blinky_taskdef; + +StackType_t usb_device_stack[USBD_STACK_SIZE]; +StaticTask_t usb_device_taskdef; + +StackType_t video_stack[VIDEO_STACK_SIZE]; +StaticTask_t video_taskdef; +#endif + +// USB Device Driver task +// This top level thread process all usb events and invoke callbacks +void usb_device_task(void *param) { + (void) param; + + // init device stack on configured roothub port + // This should be called after scheduler/kernel is started. + // Otherwise, it could cause kernel issue since USB IRQ handler does use RTOS queue API. + tud_init(BOARD_TUD_RHPORT); + + if (board_init_after_tusb) { + board_init_after_tusb(); + } + + // RTOS forever loop + while (1) { + // put this thread to waiting state until there is new events + tud_task(); + } +} - board_led_write(led_state); - led_state = 1 - led_state; // toggle +void freertos_init_task(void) { + #if configSUPPORT_STATIC_ALLOCATION + xTaskCreateStatic(led_blinking_task, "blinky", BLINKY_STACK_SIZE, NULL, 1, blinky_stack, &blinky_taskdef); + xTaskCreateStatic(usb_device_task, "usbd", USBD_STACK_SIZE, NULL, configMAX_PRIORITIES-1, usb_device_stack, &usb_device_taskdef); + xTaskCreateStatic(video_task, "cdc", VIDEO_STACK_SIZE, NULL, configMAX_PRIORITIES - 2, video_stack, &video_taskdef); + #else + xTaskCreate(led_blinking_task, "blinky", BLINKY_STACK_SIZE, NULL, 1, NULL); + xTaskCreate(usb_device_task, "usbd", USBD_STACK_SIZE, NULL, configMAX_PRIORITIES - 1, NULL); + xTaskCreate(video_task, "video", VIDEO_STACK_SZIE, NULL, configMAX_PRIORITIES - 2, NULL); + #endif + + // skip starting scheduler (and return) for ESP32-S2 or ESP32-S3 + #if !TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) + vTaskStartScheduler(); + #endif } +#endif diff --git a/examples/device/video_capture/src/tusb_config.h b/examples/device/video_capture/src/tusb_config.h index 274bf2b9c..bdfc37d87 100644 --- a/examples/device/video_capture/src/tusb_config.h +++ b/examples/device/video_capture/src/tusb_config.h @@ -57,6 +57,11 @@ #define CFG_TUSB_OS OPT_OS_NONE #endif +// Espressif IDF requires "freertos/" prefix in include path +#if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) +#define CFG_TUSB_OS_INC_PATH freertos/ +#endif + #ifndef CFG_TUSB_DEBUG #define CFG_TUSB_DEBUG 0 #endif @@ -97,11 +102,14 @@ // The number of video streaming interfaces #define CFG_TUD_VIDEO_STREAMING 1 -// video streaming endpoint size +// video streaming endpoint buffer size #define CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE 256 // use bulk endpoint for streaming interface -#define CFG_TUD_VIDEO_STREAMING_BULK 0 +#define CFG_TUD_VIDEO_STREAMING_BULK 1 + +//#define CFG_EXAMPLE_VIDEO_READONLY +//#define CFG_EXAMPLE_VIDEO_DISABLE_MJPEG #ifdef __cplusplus } diff --git a/examples/device/video_capture/src/usb_descriptors.c b/examples/device/video_capture/src/usb_descriptors.c index 49919fc58..f308c75a7 100644 --- a/examples/device/video_capture/src/usb_descriptors.c +++ b/examples/device/video_capture/src/usb_descriptors.c @@ -40,11 +40,30 @@ #define USB_VID 0xCafe #define USB_BCD 0x0200 +// String Descriptor Index +enum { + STRID_LANGID = 0, + STRID_MANUFACTURER, + STRID_PRODUCT, + STRID_SERIAL, + STRID_UVC_CONTROL, + STRID_UVC_STREAMING, +}; + +// array of pointer to string descriptors +char const* string_desc_arr[] = { + (const char[]) {0x09, 0x04}, // 0: is supported language is English (0x0409) + "TinyUSB", // 1: Manufacturer + "TinyUSB Device", // 2: Product + NULL, // 3: Serials will use unique ID if possible + "TinyUSB UVC Control", // 4: UVC Interface + "TinyUSB UVC Streaming", // 5: UVC Interface +}; + //--------------------------------------------------------------------+ // Device Descriptors //--------------------------------------------------------------------+ -tusb_desc_device_t const desc_device = -{ +tusb_desc_device_t const desc_device = { .bLength = sizeof(tusb_desc_device_t), .bDescriptorType = TUSB_DESC_DEVICE, .bcdUSB = USB_BCD, @@ -61,201 +80,374 @@ tusb_desc_device_t const desc_device = .idProduct = USB_PID, .bcdDevice = 0x0100, - .iManufacturer = 0x01, - .iProduct = 0x02, - .iSerialNumber = 0x03, + .iManufacturer = STRID_MANUFACTURER, + .iProduct = STRID_PRODUCT, + .iSerialNumber = STRID_SERIAL, .bNumConfigurations = 0x01 }; // Invoked when received GET DEVICE DESCRIPTOR // Application return pointer to descriptor -uint8_t const * tud_descriptor_device_cb(void) -{ - return (uint8_t const *) &desc_device; +uint8_t const* tud_descriptor_device_cb(void) { + return (uint8_t const*) &desc_device; } //--------------------------------------------------------------------+ // Configuration Descriptor //--------------------------------------------------------------------+ -#if defined(CFG_EXAMPLE_VIDEO_READONLY) && !defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) -# if 1 == CFG_TUD_VIDEO_STREAMING_BULK -# define CONFIG_TOTAL_LEN (TUD_CONFIG_DESC_LEN + TUD_VIDEO_CAPTURE_DESC_MJPEG_BULK_LEN) -# else -# define CONFIG_TOTAL_LEN (TUD_CONFIG_DESC_LEN + TUD_VIDEO_CAPTURE_DESC_MJPEG_LEN) -# endif -#else -# if 1 == CFG_TUD_VIDEO_STREAMING_BULK -# define CONFIG_TOTAL_LEN (TUD_CONFIG_DESC_LEN + TUD_VIDEO_CAPTURE_DESC_UNCOMPR_BULK_LEN) -# else -# define CONFIG_TOTAL_LEN (TUD_CONFIG_DESC_LEN + TUD_VIDEO_CAPTURE_DESC_UNCOMPR_LEN) -# endif -#endif +/* Time stamp base clock. It is a deprecated parameter. */ +#define UVC_CLOCK_FREQUENCY 27000000 + +/* video capture path */ +#define UVC_ENTITY_CAP_INPUT_TERMINAL 0x01 +#define UVC_ENTITY_CAP_OUTPUT_TERMINAL 0x02 + +enum { + ITF_NUM_VIDEO_CONTROL, + ITF_NUM_VIDEO_STREAMING, + ITF_NUM_TOTAL +}; +// Select appropriate endpoint number #if TU_CHECK_MCU(OPT_MCU_LPC175X_6X, OPT_MCU_LPC177X_8X, OPT_MCU_LPC40XX) // LPC 17xx and 40xx endpoint type (bulk/interrupt/iso) are fixed by its number // 0 control, 1 In, 2 Bulk, 3 Iso, 4 In, 5 Bulk etc ... -#if 1 == CFG_TUD_VIDEO_STREAMING_BULK - #define EPNUM_VIDEO_IN 0x82 -#else - #define EPNUM_VIDEO_IN 0x83 -#endif - + #define EPNUM_VIDEO_IN (CFG_TUD_VIDEO_STREAMING_BULK ? 0x82 : 0x83) #elif TU_CHECK_MCU(OPT_MCU_NRF5X) // nRF5x ISO can only be endpoint 8 - #define EPNUM_VIDEO_IN 0x88 - + #define EPNUM_VIDEO_IN (CFG_TUD_VIDEO_STREAMING_BULK ? 0x81 : 0x88) #else #define EPNUM_VIDEO_IN 0x81 +#endif +#if defined(CFG_EXAMPLE_VIDEO_READONLY) && !defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) + #define USE_MJPEG 1 +#else + #define USE_MJPEG 0 #endif -uint8_t const desc_fs_configuration[] = -{ - // Config number, interface count, string index, total length, attribute, power in mA - TUD_CONFIG_DESCRIPTOR(1, ITF_NUM_TOTAL, 0, CONFIG_TOTAL_LEN, 0, 500), +#define USE_ISO_STREAMING (!CFG_TUD_VIDEO_STREAMING_BULK) - // IAD for Video Control -#if defined(CFG_EXAMPLE_VIDEO_READONLY) && !defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) -# if 1 == CFG_TUD_VIDEO_STREAMING_BULK - TUD_VIDEO_CAPTURE_DESCRIPTOR_MJPEG_BULK(4, EPNUM_VIDEO_IN, - FRAME_WIDTH, FRAME_HEIGHT, FRAME_RATE, - 64) -# else - TUD_VIDEO_CAPTURE_DESCRIPTOR_MJPEG(4, EPNUM_VIDEO_IN, - FRAME_WIDTH, FRAME_HEIGHT, FRAME_RATE, - CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE) -# endif +typedef struct TU_ATTR_PACKED { + tusb_desc_interface_t itf; + tusb_desc_video_control_header_1itf_t header; + tusb_desc_video_control_camera_terminal_t camera_terminal; + tusb_desc_video_control_output_terminal_t output_terminal; +} uvc_control_desc_t; + +/* Windows support YUY2 and NV12 + * https://docs.microsoft.com/en-us/windows-hardware/drivers/stream/usb-video-class-driver-overview */ + +typedef struct TU_ATTR_PACKED { + tusb_desc_interface_t itf; + tusb_desc_video_streaming_input_header_1byte_t header; + +#if USE_MJPEG + tusb_desc_video_format_mjpeg_t format; + tusb_desc_video_frame_mjpeg_continuous_t frame; #else -# if 1 == CFG_TUD_VIDEO_STREAMING_BULK - TUD_VIDEO_CAPTURE_DESCRIPTOR_UNCOMPR_BULK(4, EPNUM_VIDEO_IN, - FRAME_WIDTH, FRAME_HEIGHT, FRAME_RATE, - 64) -# else - TUD_VIDEO_CAPTURE_DESCRIPTOR_UNCOMPR(4, EPNUM_VIDEO_IN, - FRAME_WIDTH, FRAME_HEIGHT, FRAME_RATE, - CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE) -# endif + tusb_desc_video_format_uncompressed_t format; + tusb_desc_video_frame_uncompressed_continuous_t frame; #endif -}; -#if TUD_OPT_HIGH_SPEED -// Per USB specs: high speed capable device must report device_qualifier and other_speed_configuration + tusb_desc_video_streaming_color_matching_t color; -uint8_t const desc_hs_configuration[] = -{ - // Config number, interface count, string index, total length, attribute, power in mA - TUD_CONFIG_DESCRIPTOR(1, ITF_NUM_TOTAL, 0, CONFIG_TOTAL_LEN, 0, 500), +#if USE_ISO_STREAMING + // For ISO streaming, USB spec requires to alternate interface + tusb_desc_interface_t itf_alt; +#endif - // IAD for Video Control -#if defined(CFG_EXAMPLE_VIDEO_READONLY) && !defined(CFG_EXAMPLE_VIDEO_DISABLE_MJPEG) -# if 1 == CFG_TUD_VIDEO_STREAMING_BULK - TUD_VIDEO_CAPTURE_DESCRIPTOR_MJPEG_BULK(4, EPNUM_VIDEO_IN, - FRAME_WIDTH, FRAME_HEIGHT, FRAME_RATE, - 512) -# else - TUD_VIDEO_CAPTURE_DESCRIPTOR_MJPEG(4, EPNUM_VIDEO_IN, - FRAME_WIDTH, FRAME_HEIGHT, FRAME_RATE, - CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE) -# endif + tusb_desc_endpoint_t ep; +} uvc_streaming_desc_t; + +typedef struct TU_ATTR_PACKED { + tusb_desc_configuration_t config; + tusb_desc_interface_assoc_t iad; + uvc_control_desc_t video_control; + uvc_streaming_desc_t video_streaming; +} uvc_cfg_desc_t; + +const uvc_cfg_desc_t desc_fs_configuration = { + .config = { + .bLength = sizeof(tusb_desc_configuration_t), + .bDescriptorType = TUSB_DESC_CONFIGURATION, + + .wTotalLength = sizeof(uvc_cfg_desc_t), + .bNumInterfaces = ITF_NUM_TOTAL, + .bConfigurationValue = 1, + .iConfiguration = 0, + .bmAttributes = TU_BIT(7), + .bMaxPower = 100 / 2 + }, + .iad = { + .bLength = sizeof(tusb_desc_interface_assoc_t), + .bDescriptorType = TUSB_DESC_INTERFACE_ASSOCIATION, + + .bFirstInterface = ITF_NUM_VIDEO_CONTROL, + .bInterfaceCount = 2, + .bFunctionClass = TUSB_CLASS_VIDEO, + .bFunctionSubClass = VIDEO_SUBCLASS_INTERFACE_COLLECTION, + .bFunctionProtocol = VIDEO_ITF_PROTOCOL_UNDEFINED, + .iFunction = 0 + }, + + .video_control = { + .itf = { + .bLength = sizeof(tusb_desc_interface_t), + .bDescriptorType = TUSB_DESC_INTERFACE, + + .bInterfaceNumber = ITF_NUM_VIDEO_CONTROL, + .bAlternateSetting = 0, + .bNumEndpoints = 0, + .bInterfaceClass = TUSB_CLASS_VIDEO, + .bInterfaceSubClass = VIDEO_SUBCLASS_CONTROL, + .bInterfaceProtocol = VIDEO_ITF_PROTOCOL_15, + .iInterface = STRID_UVC_CONTROL + }, + .header = { + .bLength = sizeof(tusb_desc_video_control_header_1itf_t), + .bDescriptorType = TUSB_DESC_CS_INTERFACE, + .bDescriptorSubType = VIDEO_CS_ITF_VC_HEADER, + + .bcdUVC = VIDEO_BCD_1_50, + .wTotalLength = sizeof(uvc_control_desc_t) - sizeof(tusb_desc_interface_t), // CS VC descriptors only + .dwClockFrequency = UVC_CLOCK_FREQUENCY, + .bInCollection = 1, + .baInterfaceNr = { ITF_NUM_VIDEO_STREAMING } + }, + .camera_terminal = { + .bLength = sizeof(tusb_desc_video_control_camera_terminal_t), + .bDescriptorType = TUSB_DESC_CS_INTERFACE, + .bDescriptorSubType = VIDEO_CS_ITF_VC_INPUT_TERMINAL, + + .bTerminalID = UVC_ENTITY_CAP_INPUT_TERMINAL, + .wTerminalType = VIDEO_ITT_CAMERA, + .bAssocTerminal = 0, + .iTerminal = 0, + .wObjectiveFocalLengthMin = 0, + .wObjectiveFocalLengthMax = 0, + .wOcularFocalLength = 0, + .bControlSize = 3, + .bmControls = { 0, 0, 0 } + }, + .output_terminal = { + .bLength = sizeof(tusb_desc_video_control_output_terminal_t), + .bDescriptorType = TUSB_DESC_CS_INTERFACE, + .bDescriptorSubType = VIDEO_CS_ITF_VC_OUTPUT_TERMINAL, + + .bTerminalID = UVC_ENTITY_CAP_OUTPUT_TERMINAL, + .wTerminalType = VIDEO_TT_STREAMING, + .bAssocTerminal = 0, + .bSourceID = UVC_ENTITY_CAP_INPUT_TERMINAL, + .iTerminal = 0 + } + }, + + .video_streaming = { + .itf = { + .bLength = sizeof(tusb_desc_interface_t), + .bDescriptorType = TUSB_DESC_INTERFACE, + + .bInterfaceNumber = ITF_NUM_VIDEO_STREAMING, + .bAlternateSetting = 0, + .bNumEndpoints = CFG_TUD_VIDEO_STREAMING_BULK, // bulk 1, iso 0 + .bInterfaceClass = TUSB_CLASS_VIDEO, + .bInterfaceSubClass = VIDEO_SUBCLASS_STREAMING, + .bInterfaceProtocol = VIDEO_ITF_PROTOCOL_15, + .iInterface = STRID_UVC_STREAMING + }, + .header = { + .bLength = sizeof(tusb_desc_video_streaming_input_header_1byte_t), + .bDescriptorType = TUSB_DESC_CS_INTERFACE, + .bDescriptorSubType = VIDEO_CS_ITF_VS_INPUT_HEADER, + + .bNumFormats = 1, + .wTotalLength = sizeof(uvc_streaming_desc_t) - sizeof(tusb_desc_interface_t) + - sizeof(tusb_desc_endpoint_t) - (USE_ISO_STREAMING ? sizeof(tusb_desc_interface_t) : 0) , // CS VS descriptors only + .bEndpointAddress = EPNUM_VIDEO_IN, + .bmInfo = 0, + .bTerminalLink = UVC_ENTITY_CAP_OUTPUT_TERMINAL, + .bStillCaptureMethod = 0, + .bTriggerSupport = 0, + .bTriggerUsage = 0, + .bControlSize = 1, + .bmaControls = { 0 } + }, + .format = { +#if USE_MJPEG + .bLength = sizeof(tusb_desc_video_format_mjpeg_t), + .bDescriptorType = TUSB_DESC_CS_INTERFACE, + .bDescriptorSubType = VIDEO_CS_ITF_VS_FORMAT_MJPEG, + .bFormatIndex = 1, // 1-based index + .bNumFrameDescriptors = 1, + .bmFlags = 0, +#else + .bLength = sizeof(tusb_desc_video_format_uncompressed_t), + .bDescriptorType = TUSB_DESC_CS_INTERFACE, + .bDescriptorSubType = VIDEO_CS_ITF_VS_FORMAT_UNCOMPRESSED, + .bFormatIndex = 1, // 1-based index + .bNumFrameDescriptors = 1, + .guidFormat = { TUD_VIDEO_GUID_YUY2 }, + .bBitsPerPixel = 16, +#endif + .bDefaultFrameIndex = 1, + .bAspectRatioX = 0, + .bAspectRatioY = 0, + .bmInterlaceFlags = 0, + .bCopyProtect = 0 + }, + .frame = { +#if USE_MJPEG + .bLength = sizeof(tusb_desc_video_frame_mjpeg_continuous_t), + .bDescriptorType = TUSB_DESC_CS_INTERFACE, + .bDescriptorSubType = VIDEO_CS_ITF_VS_FRAME_MJPEG, #else -# if 1 == CFG_TUD_VIDEO_STREAMING_BULK - TUD_VIDEO_CAPTURE_DESCRIPTOR_UNCOMPR_BULK(4, EPNUM_VIDEO_IN, - FRAME_WIDTH, FRAME_HEIGHT, FRAME_RATE, - 512) -# else - TUD_VIDEO_CAPTURE_DESCRIPTOR_UNCOMPR(4, EPNUM_VIDEO_IN, - FRAME_WIDTH, FRAME_HEIGHT, FRAME_RATE, - CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE) -# endif + .bLength = sizeof(tusb_desc_video_frame_uncompressed_continuous_t), + .bDescriptorType = TUSB_DESC_CS_INTERFACE, + .bDescriptorSubType = VIDEO_CS_ITF_VS_FRAME_UNCOMPRESSED, #endif + .bFrameIndex = 1, // 1-based index + .bmCapabilities = 0, + .wWidth = FRAME_WIDTH, + .wHeight = FRAME_HEIGHT, + .dwMinBitRate = FRAME_WIDTH * FRAME_HEIGHT * 16 * 1, + .dwMaxBitRate = FRAME_WIDTH * FRAME_HEIGHT * 16 * FRAME_RATE, + .dwMaxVideoFrameBufferSize = FRAME_WIDTH * FRAME_HEIGHT * 16 / 8, + .dwDefaultFrameInterval = 10000000 / FRAME_RATE, + .bFrameIntervalType = 0, // continuous + .dwFrameInterval = { + 10000000 / FRAME_RATE, // min + 10000000, // max + 10000000 / FRAME_RATE // step + } + }, + .color = { + .bLength = sizeof(tusb_desc_video_streaming_color_matching_t), + .bDescriptorType = TUSB_DESC_CS_INTERFACE, + .bDescriptorSubType = VIDEO_CS_ITF_VS_COLORFORMAT, + + .bColorPrimaries = VIDEO_COLOR_PRIMARIES_BT709, + .bTransferCharacteristics = VIDEO_COLOR_XFER_CH_BT709, + .bMatrixCoefficients = VIDEO_COLOR_COEF_SMPTE170M + }, + +#if USE_ISO_STREAMING + .itf_alt = { + .bLength = sizeof(tusb_desc_interface_t), + .bDescriptorType = TUSB_DESC_INTERFACE, + + .bInterfaceNumber = ITF_NUM_VIDEO_STREAMING, + .bAlternateSetting = 1, + .bNumEndpoints = 1, + .bInterfaceClass = TUSB_CLASS_VIDEO, + .bInterfaceSubClass = VIDEO_SUBCLASS_STREAMING, + .bInterfaceProtocol = VIDEO_ITF_PROTOCOL_15, + .iInterface = STRID_UVC_STREAMING + }, +#endif + + .ep = { + .bLength = sizeof(tusb_desc_endpoint_t), + .bDescriptorType = TUSB_DESC_ENDPOINT, + + .bEndpointAddress = EPNUM_VIDEO_IN, + .bmAttributes = { + .xfer = CFG_TUD_VIDEO_STREAMING_BULK ? TUSB_XFER_BULK : TUSB_XFER_ISOCHRONOUS, + .sync = CFG_TUD_VIDEO_STREAMING_BULK ? 0 : 1 // asynchronous + }, + .wMaxPacketSize = CFG_TUD_VIDEO_STREAMING_BULK ? 64 : CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE, + .bInterval = 1 + } + } }; +#if TUD_OPT_HIGH_SPEED +uvc_cfg_desc_t desc_hs_configuration; + +static uint8_t * get_hs_configuration_desc(void) { + static bool init = false; + + if (!init) { + desc_hs_configuration = desc_fs_configuration; + // change endpoint bulk size to 512 if bulk streaming + if (CFG_TUD_VIDEO_STREAMING_BULK) { + desc_hs_configuration.video_streaming.ep.wMaxPacketSize = 512; + } + } + init = true; + + return (uint8_t *) &desc_hs_configuration; +} + // device qualifier is mostly similar to device descriptor since we don't change configuration based on speed -tusb_desc_device_qualifier_t const desc_device_qualifier = -{ - .bLength = sizeof(tusb_desc_device_t), - .bDescriptorType = TUSB_DESC_DEVICE, - .bcdUSB = USB_BCD, - - .bDeviceClass = TUSB_CLASS_MISC, - .bDeviceSubClass = MISC_SUBCLASS_COMMON, - .bDeviceProtocol = MISC_PROTOCOL_IAD, - - .bMaxPacketSize0 = CFG_TUD_ENDPOINT0_SIZE, - .bNumConfigurations = 0x01, - .bReserved = 0x00 +tusb_desc_device_qualifier_t const desc_device_qualifier = { + .bLength = sizeof(tusb_desc_device_t), + .bDescriptorType = TUSB_DESC_DEVICE, + .bcdUSB = USB_BCD, + + .bDeviceClass = TUSB_CLASS_MISC, + .bDeviceSubClass = MISC_SUBCLASS_COMMON, + .bDeviceProtocol = MISC_PROTOCOL_IAD, + + .bMaxPacketSize0 = CFG_TUD_ENDPOINT0_SIZE, + .bNumConfigurations = 0x01, + .bReserved = 0x00 }; // Invoked when received GET DEVICE QUALIFIER DESCRIPTOR request // Application return pointer to descriptor, whose contents must exist long enough for transfer to complete. // device_qualifier descriptor describes information about a high-speed capable device that would // change if the device were operating at the other speed. If not highspeed capable stall this request. -uint8_t const* tud_descriptor_device_qualifier_cb(void) -{ +uint8_t const* tud_descriptor_device_qualifier_cb(void) { return (uint8_t const*) &desc_device_qualifier; } // Invoked when received GET OTHER SEED CONFIGURATION DESCRIPTOR request // Application return pointer to descriptor, whose contents must exist long enough for transfer to complete // Configuration descriptor in the other speed e.g if high speed then this is for full speed and vice versa -uint8_t const* tud_descriptor_other_speed_configuration_cb(uint8_t index) -{ +uint8_t const* tud_descriptor_other_speed_configuration_cb(uint8_t index) { (void) index; // for multiple configurations - // if link speed is high return fullspeed config, and vice versa - return (tud_speed_get() == TUSB_SPEED_HIGH) ? desc_fs_configuration : desc_hs_configuration; + if (tud_speed_get() == TUSB_SPEED_HIGH) { + return (uint8_t const*) &desc_fs_configuration; + } else { + return get_hs_configuration_desc(); + } } - #endif // highspeed // Invoked when received GET CONFIGURATION DESCRIPTOR // Application return pointer to descriptor // Descriptor contents must exist long enough for transfer to complete -uint8_t const * tud_descriptor_configuration_cb(uint8_t index) -{ +uint8_t const* tud_descriptor_configuration_cb(uint8_t index) { (void) index; // for multiple configurations #if TUD_OPT_HIGH_SPEED // Although we are highspeed, host may be fullspeed. - return (tud_speed_get() == TUSB_SPEED_HIGH) ? desc_hs_configuration : desc_fs_configuration; -#else - return desc_fs_configuration; + if (tud_speed_get() == TUSB_SPEED_HIGH) { + return get_hs_configuration_desc(); + } else #endif + { + return (uint8_t const*) &desc_fs_configuration; + } } //--------------------------------------------------------------------+ // String Descriptors //--------------------------------------------------------------------+ -// String Descriptor Index -enum { - STRID_LANGID = 0, - STRID_MANUFACTURER, - STRID_PRODUCT, - STRID_SERIAL, -}; - -// array of pointer to string descriptors -char const *string_desc_arr[] = -{ - (const char[]) { 0x09, 0x04 }, // 0: is supported language is English (0x0409) - "TinyUSB", // 1: Manufacturer - "TinyUSB Device", // 2: Product - NULL, // 3: Serials will use unique ID if possible - "TinyUSB UVC", // 4: UVC Interface -}; - static uint16_t _desc_str[32 + 1]; // Invoked when received GET STRING DESCRIPTOR request // Application return pointer to descriptor, whose contents must exist long enough for transfer to complete -uint16_t const *tud_descriptor_string_cb(uint8_t index, uint16_t langid) { +uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) { (void) langid; size_t chr_count; - switch ( index ) { + switch (index) { case STRID_LANGID: memcpy(&_desc_str[1], string_desc_arr[0], 2); chr_count = 1; @@ -269,17 +461,17 @@ uint16_t const *tud_descriptor_string_cb(uint8_t index, uint16_t langid) { // Note: the 0xEE index string is a Microsoft OS 1.0 Descriptors. // https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/microsoft-defined-usb-descriptors - if ( !(index < sizeof(string_desc_arr) / sizeof(string_desc_arr[0])) ) return NULL; + if (index >= sizeof(string_desc_arr) / sizeof(string_desc_arr[0])) return NULL; - const char *str = string_desc_arr[index]; + const char* str = string_desc_arr[index]; // Cap at max char chr_count = strlen(str); size_t const max_count = sizeof(_desc_str) / sizeof(_desc_str[0]) - 1; // -1 for string type - if ( chr_count > max_count ) chr_count = max_count; + if (chr_count > max_count) chr_count = max_count; // Convert ASCII string into UTF-16 - for ( size_t i = 0; i < chr_count; i++ ) { + for (size_t i = 0; i < chr_count; i++) { _desc_str[1 + i] = str[i]; } break; diff --git a/examples/device/video_capture/src/usb_descriptors.h b/examples/device/video_capture/src/usb_descriptors.h index b924c8dbe..12d41b2f3 100644 --- a/examples/device/video_capture/src/usb_descriptors.h +++ b/examples/device/video_capture/src/usb_descriptors.h @@ -27,21 +27,11 @@ #ifndef _USB_DESCRIPTORS_H_ #define _USB_DESCRIPTORS_H_ -/* Time stamp base clock. It is a deprecated parameter. */ -#define UVC_CLOCK_FREQUENCY 27000000 -/* video capture path */ -#define UVC_ENTITY_CAP_INPUT_TERMINAL 0x01 -#define UVC_ENTITY_CAP_OUTPUT_TERMINAL 0x02 - #define FRAME_WIDTH 128 #define FRAME_HEIGHT 96 #define FRAME_RATE 10 -enum { - ITF_NUM_VIDEO_CONTROL, - ITF_NUM_VIDEO_STREAMING, - ITF_NUM_TOTAL -}; +// NOTE: descriptor template is not used but leave here as reference #define TUD_VIDEO_CAPTURE_DESC_UNCOMPR_LEN (\ TUD_VIDEO_DESC_IAD_LEN\ @@ -126,23 +116,17 @@ enum { #define TUD_VIDEO_CAPTURE_DESCRIPTOR_UNCOMPR(_stridx, _epin, _width, _height, _fps, _epsize) \ TUD_VIDEO_DESC_IAD(ITF_NUM_VIDEO_CONTROL, /* 2 Interfaces */ 0x02, _stridx), \ /* Video control 0 */ \ - TUD_VIDEO_DESC_STD_VC(ITF_NUM_VIDEO_CONTROL, 0, _stridx), \ - TUD_VIDEO_DESC_CS_VC( /* UVC 1.5*/ 0x0150, \ - /* wTotalLength - bLength */ \ - TUD_VIDEO_DESC_CAMERA_TERM_LEN + TUD_VIDEO_DESC_OUTPUT_TERM_LEN, \ - UVC_CLOCK_FREQUENCY, ITF_NUM_VIDEO_STREAMING), \ - TUD_VIDEO_DESC_CAMERA_TERM(UVC_ENTITY_CAP_INPUT_TERMINAL, 0, 0,\ - /*wObjectiveFocalLengthMin*/0, /*wObjectiveFocalLengthMax*/0,\ - /*wObjectiveFocalLength*/0, /*bmControls*/0), \ + TUD_VIDEO_DESC_STD_VC(ITF_NUM_VIDEO_CONTROL, 0, _stridx), \ + /* Header: UVC 1.5, length of followed descs, clock (deprecated), streaming interfaces */ \ + TUD_VIDEO_DESC_CS_VC(0x0150, TUD_VIDEO_DESC_CAMERA_TERM_LEN + TUD_VIDEO_DESC_OUTPUT_TERM_LEN, UVC_CLOCK_FREQUENCY, ITF_NUM_VIDEO_STREAMING), \ + /* Camera Terminal: ID, bAssocTerminal, iTerminal, focal min, max, length, bmControl */ \ + TUD_VIDEO_DESC_CAMERA_TERM(UVC_ENTITY_CAP_INPUT_TERMINAL, 0, 0, 0, 0, 0, 0), \ TUD_VIDEO_DESC_OUTPUT_TERM(UVC_ENTITY_CAP_OUTPUT_TERMINAL, VIDEO_TT_STREAMING, 0, 1, 0), \ /* Video stream alt. 0 */ \ TUD_VIDEO_DESC_STD_VS(ITF_NUM_VIDEO_STREAMING, 0, 0, _stridx), \ /* Video stream header for without still image capture */ \ TUD_VIDEO_DESC_CS_VS_INPUT( /*bNumFormats*/1, \ - /*wTotalLength - bLength */\ - TUD_VIDEO_DESC_CS_VS_FMT_UNCOMPR_LEN\ - + TUD_VIDEO_DESC_CS_VS_FRM_UNCOMPR_CONT_LEN\ - + TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING_LEN,\ + /*wTotalLength - bLength */ TUD_VIDEO_DESC_CS_VS_FMT_UNCOMPR_LEN + TUD_VIDEO_DESC_CS_VS_FRM_UNCOMPR_CONT_LEN + TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING_LEN,\ _epin, /*bmInfo*/0, /*bTerminalLink*/UVC_ENTITY_CAP_OUTPUT_TERMINAL, \ /*bStillCaptureMethod*/0, /*bTriggerSupport*/0, /*bTriggerUsage*/0, \ /*bmaControls(1)*/0), \ @@ -152,7 +136,7 @@ enum { /* Video stream frame format */ \ TUD_VIDEO_DESC_CS_VS_FRM_UNCOMPR_CONT(/*bFrameIndex */1, 0, _width, _height, \ _width * _height * 16, _width * _height * 16 * _fps, \ - _width * _height * 16, \ + _width * _height * 16 / 8, \ (10000000/_fps), (10000000/_fps), (10000000/_fps)*_fps, (10000000/_fps)), \ TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING(VIDEO_COLOR_PRIMARIES_BT709, VIDEO_COLOR_XFER_CH_BT709, VIDEO_COLOR_COEF_SMPTE170M), \ /* VS alt 1 */\ @@ -163,23 +147,17 @@ enum { #define TUD_VIDEO_CAPTURE_DESCRIPTOR_MJPEG(_stridx, _epin, _width, _height, _fps, _epsize) \ TUD_VIDEO_DESC_IAD(ITF_NUM_VIDEO_CONTROL, /* 2 Interfaces */ 0x02, _stridx), \ /* Video control 0 */ \ - TUD_VIDEO_DESC_STD_VC(ITF_NUM_VIDEO_CONTROL, 0, _stridx), \ - TUD_VIDEO_DESC_CS_VC( /* UVC 1.5*/ 0x0150, \ - /* wTotalLength - bLength */ \ - TUD_VIDEO_DESC_CAMERA_TERM_LEN + TUD_VIDEO_DESC_OUTPUT_TERM_LEN, \ - UVC_CLOCK_FREQUENCY, ITF_NUM_VIDEO_STREAMING), \ - TUD_VIDEO_DESC_CAMERA_TERM(UVC_ENTITY_CAP_INPUT_TERMINAL, 0, 0,\ - /*wObjectiveFocalLengthMin*/0, /*wObjectiveFocalLengthMax*/0,\ - /*wObjectiveFocalLength*/0, /*bmControls*/0), \ + TUD_VIDEO_DESC_STD_VC(ITF_NUM_VIDEO_CONTROL, 0, _stridx), \ + /* Header: UVC 1.5, length of followed descs, clock (deprecated), streaming interfaces */ \ + TUD_VIDEO_DESC_CS_VC(0x0150, TUD_VIDEO_DESC_CAMERA_TERM_LEN + TUD_VIDEO_DESC_OUTPUT_TERM_LEN, UVC_CLOCK_FREQUENCY, ITF_NUM_VIDEO_STREAMING), \ + /* Camera Terminal: ID, bAssocTerminal, iTerminal, focal min, max, length, bmControl */ \ + TUD_VIDEO_DESC_CAMERA_TERM(UVC_ENTITY_CAP_INPUT_TERMINAL, 0, 0, 0, 0, 0, 0), \ TUD_VIDEO_DESC_OUTPUT_TERM(UVC_ENTITY_CAP_OUTPUT_TERMINAL, VIDEO_TT_STREAMING, 0, 1, 0), \ /* Video stream alt. 0 */ \ TUD_VIDEO_DESC_STD_VS(ITF_NUM_VIDEO_STREAMING, 0, 0, _stridx), \ /* Video stream header for without still image capture */ \ TUD_VIDEO_DESC_CS_VS_INPUT( /*bNumFormats*/1, \ - /*wTotalLength - bLength */\ - TUD_VIDEO_DESC_CS_VS_FMT_MJPEG_LEN\ - + TUD_VIDEO_DESC_CS_VS_FRM_MJPEG_CONT_LEN\ - + TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING_LEN,\ + /*wTotalLength - bLength */ TUD_VIDEO_DESC_CS_VS_FMT_MJPEG_LEN + TUD_VIDEO_DESC_CS_VS_FRM_MJPEG_CONT_LEN + TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING_LEN,\ _epin, /*bmInfo*/0, /*bTerminalLink*/UVC_ENTITY_CAP_OUTPUT_TERMINAL, \ /*bStillCaptureMethod*/0, /*bTriggerSupport*/0, /*bTriggerUsage*/0, \ /*bmaControls(1)*/0), \ @@ -202,22 +180,17 @@ enum { TUD_VIDEO_DESC_IAD(ITF_NUM_VIDEO_CONTROL, /* 2 Interfaces */ 0x02, _stridx), \ /* Video control 0 */ \ TUD_VIDEO_DESC_STD_VC(ITF_NUM_VIDEO_CONTROL, 0, _stridx), \ - TUD_VIDEO_DESC_CS_VC( /* UVC 1.5*/ 0x0150, \ - /* wTotalLength - bLength */ \ - TUD_VIDEO_DESC_CAMERA_TERM_LEN + TUD_VIDEO_DESC_OUTPUT_TERM_LEN, \ - UVC_CLOCK_FREQUENCY, ITF_NUM_VIDEO_STREAMING), \ - TUD_VIDEO_DESC_CAMERA_TERM(UVC_ENTITY_CAP_INPUT_TERMINAL, 0, 0,\ - /*wObjectiveFocalLengthMin*/0, /*wObjectiveFocalLengthMax*/0,\ - /*wObjectiveFocalLength*/0, /*bmControls*/0), \ + /* Header: UVC 1.5, length of followed descs, clock (deprecated), streaming interfaces */ \ + TUD_VIDEO_DESC_CS_VC(0x0150, TUD_VIDEO_DESC_CAMERA_TERM_LEN + TUD_VIDEO_DESC_OUTPUT_TERM_LEN, UVC_CLOCK_FREQUENCY, ITF_NUM_VIDEO_STREAMING), \ + /* Camera Terminal: ID, bAssocTerminal, iTerminal, focal min, max, length, bmControl */ \ + TUD_VIDEO_DESC_CAMERA_TERM(UVC_ENTITY_CAP_INPUT_TERMINAL, 0, 0, 0, 0, 0, 0), \ TUD_VIDEO_DESC_OUTPUT_TERM(UVC_ENTITY_CAP_OUTPUT_TERMINAL, VIDEO_TT_STREAMING, 0, 1, 0), \ /* Video stream alt. 0 */ \ TUD_VIDEO_DESC_STD_VS(ITF_NUM_VIDEO_STREAMING, 0, 1, _stridx), \ /* Video stream header for without still image capture */ \ TUD_VIDEO_DESC_CS_VS_INPUT( /*bNumFormats*/1, \ /*wTotalLength - bLength */\ - TUD_VIDEO_DESC_CS_VS_FMT_UNCOMPR_LEN\ - + TUD_VIDEO_DESC_CS_VS_FRM_UNCOMPR_CONT_LEN\ - + TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING_LEN,\ + TUD_VIDEO_DESC_CS_VS_FMT_UNCOMPR_LEN + TUD_VIDEO_DESC_CS_VS_FRM_UNCOMPR_CONT_LEN + TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING_LEN,\ _epin, /*bmInfo*/0, /*bTerminalLink*/UVC_ENTITY_CAP_OUTPUT_TERMINAL, \ /*bStillCaptureMethod*/0, /*bTriggerSupport*/0, /*bTriggerUsage*/0, \ /*bmaControls(1)*/0), \ @@ -227,7 +200,7 @@ enum { /* Video stream frame format */ \ TUD_VIDEO_DESC_CS_VS_FRM_UNCOMPR_CONT(/*bFrameIndex */1, 0, _width, _height, \ _width * _height * 16, _width * _height * 16 * _fps, \ - _width * _height * 16, \ + _width * _height * 16 / 8, \ (10000000/_fps), (10000000/_fps), (10000000/_fps)*_fps, (10000000/_fps)), \ TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING(VIDEO_COLOR_PRIMARIES_BT709, VIDEO_COLOR_XFER_CH_BT709, VIDEO_COLOR_COEF_SMPTE170M), \ TUD_VIDEO_DESC_EP_BULK(_epin, _epsize, 1) @@ -235,23 +208,17 @@ enum { #define TUD_VIDEO_CAPTURE_DESCRIPTOR_MJPEG_BULK(_stridx, _epin, _width, _height, _fps, _epsize) \ TUD_VIDEO_DESC_IAD(ITF_NUM_VIDEO_CONTROL, /* 2 Interfaces */ 0x02, _stridx), \ /* Video control 0 */ \ - TUD_VIDEO_DESC_STD_VC(ITF_NUM_VIDEO_CONTROL, 0, _stridx), \ - TUD_VIDEO_DESC_CS_VC( /* UVC 1.5*/ 0x0150, \ - /* wTotalLength - bLength */ \ - TUD_VIDEO_DESC_CAMERA_TERM_LEN + TUD_VIDEO_DESC_OUTPUT_TERM_LEN, \ - UVC_CLOCK_FREQUENCY, ITF_NUM_VIDEO_STREAMING), \ - TUD_VIDEO_DESC_CAMERA_TERM(UVC_ENTITY_CAP_INPUT_TERMINAL, 0, 0,\ - /*wObjectiveFocalLengthMin*/0, /*wObjectiveFocalLengthMax*/0,\ - /*wObjectiveFocalLength*/0, /*bmControls*/0), \ - TUD_VIDEO_DESC_OUTPUT_TERM(UVC_ENTITY_CAP_OUTPUT_TERMINAL, VIDEO_TT_STREAMING, 0, 1, 0), \ + TUD_VIDEO_DESC_STD_VC(ITF_NUM_VIDEO_CONTROL, 0, _stridx), \ + /* Header: UVC 1.5, length of followed descs, clock (deprecated), streaming interfaces */ \ + TUD_VIDEO_DESC_CS_VC(0x0150, TUD_VIDEO_DESC_CAMERA_TERM_LEN + TUD_VIDEO_DESC_OUTPUT_TERM_LEN, UVC_CLOCK_FREQUENCY, ITF_NUM_VIDEO_STREAMING), \ + /* Camera Terminal: ID, bAssocTerminal, iTerminal, focal min, max, length, bmControl */ \ + TUD_VIDEO_DESC_CAMERA_TERM(UVC_ENTITY_CAP_INPUT_TERMINAL, 0, 0, 0, 0, 0, 0), \ + TUD_VIDEO_DESC_OUTPUT_TERM(UVC_ENTITY_CAP_OUTPUT_TERMINAL, VIDEO_TT_STREAMING, 0, UVC_ENTITY_CAP_INPUT_TERMINAL, 0), \ /* Video stream alt. 0 */ \ TUD_VIDEO_DESC_STD_VS(ITF_NUM_VIDEO_STREAMING, 0, 1, _stridx), \ /* Video stream header for without still image capture */ \ TUD_VIDEO_DESC_CS_VS_INPUT( /*bNumFormats*/1, \ - /*wTotalLength - bLength */\ - TUD_VIDEO_DESC_CS_VS_FMT_MJPEG_LEN\ - + TUD_VIDEO_DESC_CS_VS_FRM_MJPEG_CONT_LEN\ - + TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING_LEN,\ + /*wTotalLength - bLength */ TUD_VIDEO_DESC_CS_VS_FMT_MJPEG_LEN + TUD_VIDEO_DESC_CS_VS_FRM_MJPEG_CONT_LEN + TUD_VIDEO_DESC_CS_VS_COLOR_MATCHING_LEN,\ _epin, /*bmInfo*/0, /*bTerminalLink*/UVC_ENTITY_CAP_OUTPUT_TERMINAL, \ /*bStillCaptureMethod*/0, /*bTriggerSupport*/0, /*bTriggerUsage*/0, \ /*bmaControls(1)*/0), \ diff --git a/examples/host/cdc_msc_hid/src/cdc_app.c b/examples/host/cdc_msc_hid/src/cdc_app.c index a1b26e49c..e275e7943 100644 --- a/examples/host/cdc_msc_hid/src/cdc_app.c +++ b/examples/host/cdc_msc_hid/src/cdc_app.c @@ -27,20 +27,11 @@ #include "tusb.h" #include "bsp/board_api.h" -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM DECLARATION -//--------------------------------------------------------------------+ - - -//------------- IMPLEMENTATION -------------// - -size_t get_console_inputs(uint8_t* buf, size_t bufsize) -{ +size_t get_console_inputs(uint8_t* buf, size_t bufsize) { size_t count = 0; - while (count < bufsize) - { + while (count < bufsize) { int ch = board_getchar(); - if ( ch <= 0 ) break; + if (ch <= 0) break; buf[count] = (uint8_t) ch; count++; @@ -49,22 +40,18 @@ size_t get_console_inputs(uint8_t* buf, size_t bufsize) return count; } -void cdc_app_task(void) -{ - uint8_t buf[64+1]; // +1 for extra null character - uint32_t const bufsize = sizeof(buf)-1; +void cdc_app_task(void) { + uint8_t buf[64 + 1]; // +1 for extra null character + uint32_t const bufsize = sizeof(buf) - 1; uint32_t count = get_console_inputs(buf, bufsize); buf[count] = 0; // loop over all mounted interfaces - for(uint8_t idx=0; idx cdc interfaces - if (count) - { + if (count) { tuh_cdc_write(idx, buf, count); tuh_cdc_write_flush(idx); } @@ -72,11 +59,14 @@ void cdc_app_task(void) } } +//--------------------------------------------------------------------+ +// TinyUSB callbacks +//--------------------------------------------------------------------+ + // Invoked when received new data -void tuh_cdc_rx_cb(uint8_t idx) -{ - uint8_t buf[64+1]; // +1 for extra null character - uint32_t const bufsize = sizeof(buf)-1; +void tuh_cdc_rx_cb(uint8_t idx) { + uint8_t buf[64 + 1]; // +1 for extra null character + uint32_t const bufsize = sizeof(buf) - 1; // forward cdc interfaces -> console uint32_t count = tuh_cdc_read(idx, buf, bufsize); @@ -85,29 +75,35 @@ void tuh_cdc_rx_cb(uint8_t idx) printf((char*) buf); } -void tuh_cdc_mount_cb(uint8_t idx) -{ - tuh_itf_info_t itf_info = { 0 }; +// Invoked when a device with CDC interface is mounted +// idx is index of cdc interface in the internal pool. +void tuh_cdc_mount_cb(uint8_t idx) { + tuh_itf_info_t itf_info = {0}; tuh_cdc_itf_get_info(idx, &itf_info); - printf("CDC Interface is mounted: address = %u, itf_num = %u\r\n", itf_info.daddr, itf_info.desc.bInterfaceNumber); + printf("CDC Interface is mounted: address = %u, itf_num = %u\r\n", itf_info.daddr, + itf_info.desc.bInterfaceNumber); #ifdef CFG_TUH_CDC_LINE_CODING_ON_ENUM - // CFG_TUH_CDC_LINE_CODING_ON_ENUM must be defined for line coding is set by tinyusb in enumeration - // otherwise you need to call tuh_cdc_set_line_coding() first - cdc_line_coding_t line_coding = { 0 }; - if ( tuh_cdc_get_local_line_coding(idx, &line_coding) ) - { + // If CFG_TUH_CDC_LINE_CODING_ON_ENUM is defined, line coding will be set by tinyusb stack + // while eneumerating new cdc device + cdc_line_coding_t line_coding = {0}; + if (tuh_cdc_get_local_line_coding(idx, &line_coding)) { printf(" Baudrate: %lu, Stop Bits : %u\r\n", line_coding.bit_rate, line_coding.stop_bits); - printf(" Parity : %u, Data Width: %u\r\n", line_coding.parity , line_coding.data_bits); + printf(" Parity : %u, Data Width: %u\r\n", line_coding.parity, line_coding.data_bits); } +#else + // Set Line Coding upon mounted + cdc_line_coding_t new_line_coding = { 115200, CDC_LINE_CODING_STOP_BITS_1, CDC_LINE_CODING_PARITY_NONE, 8 }; + tuh_cdc_set_line_coding(idx, &new_line_coding, NULL, 0); #endif } -void tuh_cdc_umount_cb(uint8_t idx) -{ - tuh_itf_info_t itf_info = { 0 }; +// Invoked when a device with CDC interface is unmounted +void tuh_cdc_umount_cb(uint8_t idx) { + tuh_itf_info_t itf_info = {0}; tuh_cdc_itf_get_info(idx, &itf_info); - printf("CDC Interface is unmounted: address = %u, itf_num = %u\r\n", itf_info.daddr, itf_info.desc.bInterfaceNumber); + printf("CDC Interface is unmounted: address = %u, itf_num = %u\r\n", itf_info.daddr, + itf_info.desc.bInterfaceNumber); } diff --git a/examples/host/cdc_msc_hid/src/tusb_config.h b/examples/host/cdc_msc_hid/src/tusb_config.h index 61abb85eb..76d59c316 100644 --- a/examples/host/cdc_msc_hid/src/tusb_config.h +++ b/examples/host/cdc_msc_hid/src/tusb_config.h @@ -105,6 +105,7 @@ #define CFG_TUH_CDC 1 // CDC ACM #define CFG_TUH_CDC_FTDI 1 // FTDI Serial. FTDI is not part of CDC class, only to re-use CDC driver API #define CFG_TUH_CDC_CP210X 1 // CP210x Serial. CP210X is not part of CDC class, only to re-use CDC driver API +#define CFG_TUH_CDC_CH34X 1 // CH340 or CH341 Serial. CH34X is not part of CDC class, only to re-use CDC driver API #define CFG_TUH_HID (3*CFG_TUH_DEVICE_MAX) // typical keyboard + mouse device can have 3-4 HID interfaces #define CFG_TUH_MSC 1 #define CFG_TUH_VENDOR 0 diff --git a/examples/host/cdc_msc_hid_freertos/src/tusb_config.h b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h index c661f47be..bb7c3388d 100644 --- a/examples/host/cdc_msc_hid_freertos/src/tusb_config.h +++ b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h @@ -110,6 +110,7 @@ #define CFG_TUH_CDC 1 // CDC ACM #define CFG_TUH_CDC_FTDI 1 // FTDI Serial. FTDI is not part of CDC class, only to re-use CDC driver API #define CFG_TUH_CDC_CP210X 1 // CP210x Serial. CP210X is not part of CDC class, only to re-use CDC driver API +#define CFG_TUH_CDC_CH34X 1 // CH340 or CH341 Serial. CH34X is not part of CDC class, only to re-use CDC driver API #define CFG_TUH_HID (3*CFG_TUH_DEVICE_MAX) // typical keyboard + mouse device can have 3-4 HID interfaces #define CFG_TUH_MSC 1 #define CFG_TUH_VENDOR 0 diff --git a/hw/bsp/board_api.h b/hw/bsp/board_api.h index 404509a28..0c8a35924 100644 --- a/hw/bsp/board_api.h +++ b/hw/bsp/board_api.h @@ -33,9 +33,26 @@ extern "C" { #include #include - #include "tusb.h" +#if CFG_TUSB_OS == OPT_OS_FREERTOS +#if TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) + // ESP-IDF need "freertos/" prefix in include path. + // CFG_TUSB_OS_INC_PATH should be defined accordingly. + #include "freertos/FreeRTOS.h" + #include "freertos/semphr.h" + #include "freertos/queue.h" + #include "freertos/task.h" + #include "freertos/timers.h" +#else + #include "FreeRTOS.h" + #include "semphr.h" + #include "queue.h" + #include "task.h" + #include "timers.h" +#endif +#endif + // Define the default baudrate #ifndef CFG_BOARD_UART_BAUDRATE #define CFG_BOARD_UART_BAUDRATE 115200 ///< Default baud rate diff --git a/hw/bsp/espressif/boards/family.c b/hw/bsp/espressif/boards/family.c index 325e9ab0f..5599d1504 100644 --- a/hw/bsp/espressif/boards/family.c +++ b/hw/bsp/espressif/boards/family.c @@ -33,7 +33,7 @@ #include "hal/usb_hal.h" #include "soc/usb_periph.h" -#include "driver/rmt.h" +#include "driver/gpio.h" #include "driver/uart.h" #if ESP_IDF_VERSION_MAJOR > 4 @@ -48,7 +48,7 @@ #ifdef NEOPIXEL_PIN #include "led_strip.h" -static led_strip_t* strip; +static led_strip_handle_t led_strip; #endif #if CFG_TUH_ENABLED && CFG_TUH_MAX3421 @@ -85,15 +85,23 @@ void board_init(void) { #endif // WS2812 Neopixel driver with RMT peripheral - rmt_config_t config = RMT_DEFAULT_CONFIG_TX(NEOPIXEL_PIN, RMT_CHANNEL_0); - config.clk_div = 2; // set counter clock to 40MHz + led_strip_rmt_config_t rmt_config = { + .clk_src = RMT_CLK_SRC_DEFAULT, // different clock source can lead to different power consumption + .resolution_hz = 10 * 1000 * 1000, // RMT counter clock frequency, default = 10 Mhz + .flags.with_dma = false, // DMA feature is available on ESP target like ESP32-S3 + }; + + led_strip_config_t strip_config = { + .strip_gpio_num = NEOPIXEL_PIN, // The GPIO that connected to the LED strip's data line + .max_leds = 1, // The number of LEDs in the strip, + .led_pixel_format = LED_PIXEL_FORMAT_GRB, // Pixel format of your LED strip + .led_model = LED_MODEL_WS2812, // LED strip model + .flags.invert_out = false, // whether to invert the output signal + }; - rmt_config(&config); - rmt_driver_install(config.channel, 0, 0); + ESP_ERROR_CHECK(led_strip_new_rmt_device(&strip_config, &rmt_config, &led_strip)); - led_strip_config_t strip_config = LED_STRIP_DEFAULT_CONFIG(1, (led_strip_dev_t) config.channel); - strip = led_strip_new_rmt_ws2812(&strip_config); - strip->clear(strip, 100); // off led + led_strip_clear(led_strip); // off #endif // Button @@ -158,8 +166,8 @@ size_t board_get_unique_id(uint8_t id[], size_t max_len) { void board_led_write(bool state) { #ifdef NEOPIXEL_PIN - strip->set_pixel(strip, 0, state ? 0x08 : 0x00, 0x00, 0x00); - strip->refresh(strip, 100); + led_strip_set_pixel(led_strip, 0, state ? 0x08 : 0x00, 0x00, 0x00); + led_strip_refresh(led_strip); #endif } diff --git a/hw/bsp/espressif/components/led_strip/CHANGELOG.md b/hw/bsp/espressif/components/led_strip/CHANGELOG.md new file mode 100644 index 000000000..51c0cd30c --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/CHANGELOG.md @@ -0,0 +1,38 @@ +## 2.5.0 + +- Enabled support for IDF4.4 and above + - with RMT backend only +- Added API `led_strip_set_pixel_hsv` + +## 2.4.0 + +- Support configurable SPI mode to control leds + - recommend enabling DMA when using SPI mode + +## 2.3.0 + +- Support configurable RMT channel size by setting `mem_block_symbols` + +## 2.2.0 + +- Support for 4 components RGBW leds (SK6812): + - in led_strip_config_t new fields + led_pixel_format, controlling byte format (LED_PIXEL_FORMAT_GRB, LED_PIXEL_FORMAT_GRBW) + led_model, used to configure bit timing (LED_MODEL_WS2812, LED_MODEL_SK6812) + - new API led_strip_set_pixel_rgbw + - new interface type set_pixel_rgbw + +## 2.1.0 + +- Support DMA feature, which offloads the CPU by a lot when it comes to drive a bunch of LEDs +- Support various RMT clock sources +- Acquire and release the power management lock before and after each refresh +- New driver flag: `invert_out` which can invert the led control signal by hardware + +## 2.0.0 + +- Reimplemented the driver using the new RMT driver (`driver/rmt_tx.h`) + +## 1.0.0 + +- Initial driver version, based on the legacy RMT driver (`driver/rmt.h`) diff --git a/hw/bsp/espressif/components/led_strip/CMakeLists.txt b/hw/bsp/espressif/components/led_strip/CMakeLists.txt index 8266c5a1c..15de610cc 100644 --- a/hw/bsp/espressif/components/led_strip/CMakeLists.txt +++ b/hw/bsp/espressif/components/led_strip/CMakeLists.txt @@ -1,7 +1,22 @@ -set(component_srcs "src/led_strip_rmt_ws2812.c") +include($ENV{IDF_PATH}/tools/cmake/version.cmake) -idf_component_register(SRCS "${component_srcs}" - INCLUDE_DIRS "include" - PRIV_INCLUDE_DIRS "" - PRIV_REQUIRES "driver" - REQUIRES "") +set(srcs "src/led_strip_api.c") + +if("${IDF_VERSION_MAJOR}.${IDF_VERSION_MINOR}" VERSION_GREATER_EQUAL "5.0") + if(CONFIG_SOC_RMT_SUPPORTED) + list(APPEND srcs "src/led_strip_rmt_dev.c" "src/led_strip_rmt_encoder.c") + endif() +else() + list(APPEND srcs "src/led_strip_rmt_dev_idf4.c") +endif() + +# the SPI backend driver relies on something that was added in IDF 5.1 +if("${IDF_VERSION_MAJOR}.${IDF_VERSION_MINOR}" VERSION_GREATER_EQUAL "5.1") + if(CONFIG_SOC_GPSPI_SUPPORTED) + list(APPEND srcs "src/led_strip_spi_dev.c") + endif() +endif() + +idf_component_register(SRCS ${srcs} + INCLUDE_DIRS "include" "interface" + REQUIRES "driver") diff --git a/hw/bsp/espressif/components/led_strip/LICENSE b/hw/bsp/espressif/components/led_strip/LICENSE new file mode 100644 index 000000000..d64569567 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/LICENSE @@ -0,0 +1,202 @@ + + Apache License + Version 2.0, January 2004 + http://www.apache.org/licenses/ + + TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION + + 1. Definitions. + + "License" shall mean the terms and conditions for use, reproduction, + and distribution as defined by Sections 1 through 9 of this document. + + "Licensor" shall mean the copyright owner or entity authorized by + the copyright owner that is granting the License. + + "Legal Entity" shall mean the union of the acting entity and all + other entities that control, are controlled by, or are under common + control with that entity. For the purposes of this definition, + "control" means (i) the power, direct or indirect, to cause the + direction or management of such entity, whether by contract or + otherwise, or (ii) ownership of fifty percent (50%) or more of the + outstanding shares, or (iii) beneficial ownership of such entity. + + "You" (or "Your") shall mean an individual or Legal Entity + exercising permissions granted by this License. + + "Source" form shall mean the preferred form for making modifications, + including but not limited to software source code, documentation + source, and configuration files. + + "Object" form shall mean any form resulting from mechanical + transformation or translation of a Source form, including but + not limited to compiled object code, generated documentation, + and conversions to other media types. + + "Work" shall mean the work of authorship, whether in Source or + Object form, made available under the License, as indicated by a + copyright notice that is included in or attached to the work + (an example is provided in the Appendix below). + + "Derivative Works" shall mean any work, whether in Source or Object + form, that is based on (or derived from) the Work and for which the + editorial revisions, annotations, elaborations, or other modifications + represent, as a whole, an original work of authorship. For the purposes + of this License, Derivative Works shall not include works that remain + separable from, or merely link (or bind by name) to the interfaces of, + the Work and Derivative Works thereof. + + "Contribution" shall mean any work of authorship, including + the original version of the Work and any modifications or additions + to that Work or Derivative Works thereof, that is intentionally + submitted to Licensor for inclusion in the Work by the copyright owner + or by an individual or Legal Entity authorized to submit on behalf of + the copyright owner. For the purposes of this definition, "submitted" + means any form of electronic, verbal, or written communication sent + to the Licensor or its representatives, including but not limited to + communication on electronic mailing lists, source code control systems, + and issue tracking systems that are managed by, or on behalf of, the + Licensor for the purpose of discussing and improving the Work, but + excluding communication that is conspicuously marked or otherwise + designated in writing by the copyright owner as "Not a Contribution." + + "Contributor" shall mean Licensor and any individual or Legal Entity + on behalf of whom a Contribution has been received by Licensor and + subsequently incorporated within the Work. + + 2. Grant of Copyright License. Subject to the terms and conditions of + this License, each Contributor hereby grants to You a perpetual, + worldwide, non-exclusive, no-charge, royalty-free, irrevocable + copyright license to reproduce, prepare Derivative Works of, + publicly display, publicly perform, sublicense, and distribute the + Work and such Derivative Works in Source or Object form. + + 3. Grant of Patent License. Subject to the terms and conditions of + this License, each Contributor hereby grants to You a perpetual, + worldwide, non-exclusive, no-charge, royalty-free, irrevocable + (except as stated in this section) patent license to make, have made, + use, offer to sell, sell, import, and otherwise transfer the Work, + where such license applies only to those patent claims licensable + by such Contributor that are necessarily infringed by their + Contribution(s) alone or by combination of their Contribution(s) + with the Work to which such Contribution(s) was submitted. If You + institute patent litigation against any entity (including a + cross-claim or counterclaim in a lawsuit) alleging that the Work + or a Contribution incorporated within the Work constitutes direct + or contributory patent infringement, then any patent licenses + granted to You under this License for that Work shall terminate + as of the date such litigation is filed. + + 4. Redistribution. You may reproduce and distribute copies of the + Work or Derivative Works thereof in any medium, with or without + modifications, and in Source or Object form, provided that You + meet the following conditions: + + (a) You must give any other recipients of the Work or + Derivative Works a copy of this License; and + + (b) You must cause any modified files to carry prominent notices + stating that You changed the files; and + + (c) You must retain, in the Source form of any Derivative Works + that You distribute, all copyright, patent, trademark, and + attribution notices from the Source form of the Work, + excluding those notices that do not pertain to any part of + the Derivative Works; and + + (d) If the Work includes a "NOTICE" text file as part of its + distribution, then any Derivative Works that You distribute must + include a readable copy of the attribution notices contained + within such NOTICE file, excluding those notices that do not + pertain to any part of the Derivative Works, in at least one + of the following places: within a NOTICE text file distributed + as part of the Derivative Works; within the Source form or + documentation, if provided along with the Derivative Works; or, + within a display generated by the Derivative Works, if and + wherever such third-party notices normally appear. The contents + of the NOTICE file are for informational purposes only and + do not modify the License. You may add Your own attribution + notices within Derivative Works that You distribute, alongside + or as an addendum to the NOTICE text from the Work, provided + that such additional attribution notices cannot be construed + as modifying the License. + + You may add Your own copyright statement to Your modifications and + may provide additional or different license terms and conditions + for use, reproduction, or distribution of Your modifications, or + for any such Derivative Works as a whole, provided Your use, + reproduction, and distribution of the Work otherwise complies with + the conditions stated in this License. + + 5. Submission of Contributions. Unless You explicitly state otherwise, + any Contribution intentionally submitted for inclusion in the Work + by You to the Licensor shall be under the terms and conditions of + this License, without any additional terms or conditions. + Notwithstanding the above, nothing herein shall supersede or modify + the terms of any separate license agreement you may have executed + with Licensor regarding such Contributions. + + 6. Trademarks. This License does not grant permission to use the trade + names, trademarks, service marks, or product names of the Licensor, + except as required for reasonable and customary use in describing the + origin of the Work and reproducing the content of the NOTICE file. + + 7. Disclaimer of Warranty. Unless required by applicable law or + agreed to in writing, Licensor provides the Work (and each + Contributor provides its Contributions) on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or + implied, including, without limitation, any warranties or conditions + of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or FITNESS FOR A + PARTICULAR PURPOSE. You are solely responsible for determining the + appropriateness of using or redistributing the Work and assume any + risks associated with Your exercise of permissions under this License. + + 8. Limitation of Liability. In no event and under no legal theory, + whether in tort (including negligence), contract, or otherwise, + unless required by applicable law (such as deliberate and grossly + negligent acts) or agreed to in writing, shall any Contributor be + liable to You for damages, including any direct, indirect, special, + incidental, or consequential damages of any character arising as a + result of this License or out of the use or inability to use the + Work (including but not limited to damages for loss of goodwill, + work stoppage, computer failure or malfunction, or any and all + other commercial damages or losses), even if such Contributor + has been advised of the possibility of such damages. + + 9. Accepting Warranty or Additional Liability. While redistributing + the Work or Derivative Works thereof, You may choose to offer, + and charge a fee for, acceptance of support, warranty, indemnity, + or other liability obligations and/or rights consistent with this + License. However, in accepting such obligations, You may act only + on Your own behalf and on Your sole responsibility, not on behalf + of any other Contributor, and only if You agree to indemnify, + defend, and hold each Contributor harmless for any liability + incurred by, or claims asserted against, such Contributor by reason + of your accepting any such warranty or additional liability. + + END OF TERMS AND CONDITIONS + + APPENDIX: How to apply the Apache License to your work. + + To apply the Apache License to your work, attach the following + boilerplate notice, with the fields enclosed by brackets "[]" + replaced with your own identifying information. (Don't include + the brackets!) The text should be enclosed in the appropriate + comment syntax for the file format. We also recommend that a + file or class name and description of purpose be included on the + same "printed page" as the copyright notice for easier + identification within third-party archives. + + Copyright [yyyy] [name of copyright owner] + + Licensed under the Apache License, Version 2.0 (the "License"); + you may not use this file except in compliance with the License. + You may obtain a copy of the License at + + http://www.apache.org/licenses/LICENSE-2.0 + + Unless required by applicable law or agreed to in writing, software + distributed under the License is distributed on an "AS IS" BASIS, + WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. + See the License for the specific language governing permissions and + limitations under the License. diff --git a/hw/bsp/espressif/components/led_strip/README.md b/hw/bsp/espressif/components/led_strip/README.md new file mode 100644 index 000000000..543d29642 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/README.md @@ -0,0 +1,97 @@ +# LED Strip Driver + +[![Component Registry](https://components.espressif.com/components/espressif/led_strip/badge.svg)](https://components.espressif.com/components/espressif/led_strip) + +This driver is designed for addressable LEDs like [WS2812](http://www.world-semi.com/Certifications/WS2812B.html), where each LED is controlled by a single data line. + +## Backend Controllers + +### The [RMT](https://docs.espressif.com/projects/esp-idf/en/latest/esp32/api-reference/peripherals/rmt.html) Peripheral + +This is the most economical way to drive the LEDs because it only consumes one RMT channel, leaving other channels free to use. However, the memory usage increases dramatically with the number of LEDs. If the RMT hardware can't be assist by DMA, the driver will going into interrupt very frequently, thus result in a high CPU usage. What's worse, if the RMT interrupt is delayed or not serviced in time (e.g. if Wi-Fi interrupt happens on the same CPU core), the RMT transaction will be corrupted and the LEDs will display incorrect colors. If you want to use RMT to drive a large number of LEDs, you'd better to enable the DMA feature if possible [^1]. + +#### Allocate LED Strip Object with RMT Backend + +```c +#define BLINK_GPIO 0 + +led_strip_handle_t led_strip; + +/* LED strip initialization with the GPIO and pixels number*/ +led_strip_config_t strip_config = { + .strip_gpio_num = BLINK_GPIO, // The GPIO that connected to the LED strip's data line + .max_leds = 1, // The number of LEDs in the strip, + .led_pixel_format = LED_PIXEL_FORMAT_GRB, // Pixel format of your LED strip + .led_model = LED_MODEL_WS2812, // LED strip model + .flags.invert_out = false, // whether to invert the output signal (useful when your hardware has a level inverter) +}; + +led_strip_rmt_config_t rmt_config = { +#if ESP_IDF_VERSION < ESP_IDF_VERSION_VAL(5, 0, 0) + .rmt_channel = 0, +#else + .clk_src = RMT_CLK_SRC_DEFAULT, // different clock source can lead to different power consumption + .resolution_hz = 10 * 1000 * 1000, // 10MHz + .flags.with_dma = false, // whether to enable the DMA feature +#endif +}; +ESP_ERROR_CHECK(led_strip_new_rmt_device(&strip_config, &rmt_config, &led_strip)); +``` + +You can create multiple LED strip objects with different GPIOs and pixel numbers. The backend driver will automatically allocate the RMT channel for you if there is more available. + +### The [SPI](https://docs.espressif.com/projects/esp-idf/en/latest/esp32/api-reference/peripherals/spi_master.html) Peripheral + +SPI peripheral can also be used to generate the timing required by the LED strip. However this backend is not as economical as the RMT one, because it will take up the whole **bus**, unlike the RMT just takes one **channel**. You **CAN'T** connect other devices to the same SPI bus if it's been used by the led_strip, because the led_strip doesn't have the concept of "Chip Select". + +Please note, the SPI backend has a dependency of **ESP-IDF >= 5.1** + +#### Allocate LED Strip Object with SPI Backend + +```c +#define BLINK_GPIO 0 + +led_strip_handle_t led_strip; + +/* LED strip initialization with the GPIO and pixels number*/ +led_strip_config_t strip_config = { + .strip_gpio_num = BLINK_GPIO, // The GPIO that connected to the LED strip's data line + .max_leds = 1, // The number of LEDs in the strip, + .led_pixel_format = LED_PIXEL_FORMAT_GRB, // Pixel format of your LED strip + .led_model = LED_MODEL_WS2812, // LED strip model + .flags.invert_out = false, // whether to invert the output signal (useful when your hardware has a level inverter) +}; + +led_strip_spi_config_t spi_config = { + .clk_src = SPI_CLK_SRC_DEFAULT, // different clock source can lead to different power consumption + .flags.with_dma = true, // Using DMA can improve performance and help drive more LEDs + .spi_bus = SPI2_HOST, // SPI bus ID +}; +ESP_ERROR_CHECK(led_strip_new_spi_device(&strip_config, &spi_config, &led_strip)); +``` + +The number of LED strip objects can be created depends on how many free SPI buses are free to use in your project. + +## FAQ + +* Which led_strip backend should I choose? + * It depends on your application requirement and target chip's ability. + + ```mermaid + flowchart LR + A{Is RMT supported?} + A --> |No| B[SPI backend] + B --> C{Does the led strip has \n a larger number of LEDs?} + C --> |No| D[Don't have to enable the DMA of the backend] + C --> |Yes| E[Enable the DMA of the backend] + A --> |Yes| F{Does the led strip has \n a larger number of LEDs?} + F --> |Yes| G{Does RMT support DMA?} + G --> |Yes| E + G --> |No| B + F --> |No| H[RMT backend] --> D + ``` + +* How to set the brightness of the LED strip? + * You can tune the brightness by scaling the value of each R-G-B element with a **same** factor. But pay attention to the overflow of the value. + +[^1]: The RMT DMA feature is not available on all ESP chips. Please check the data sheet before using it. diff --git a/hw/bsp/espressif/components/led_strip/api.md b/hw/bsp/espressif/components/led_strip/api.md new file mode 100644 index 000000000..6581d6604 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/api.md @@ -0,0 +1,454 @@ +# API Reference + +## Header files + +- [include/led_strip.h](#file-includeled_striph) +- [include/led_strip_rmt.h](#file-includeled_strip_rmth) +- [include/led_strip_spi.h](#file-includeled_strip_spih) +- [include/led_strip_types.h](#file-includeled_strip_typesh) +- [interface/led_strip_interface.h](#file-interfaceled_strip_interfaceh) + +## File include/led_strip.h + +## Functions + +| Type | Name | +| ---: | :--- | +| esp\_err\_t | [**led\_strip\_clear**](#function-led_strip_clear) ([**led\_strip\_handle\_t**](#struct-led_strip_t) strip)
_Clear LED strip (turn off all LEDs)_ | +| esp\_err\_t | [**led\_strip\_del**](#function-led_strip_del) ([**led\_strip\_handle\_t**](#struct-led_strip_t) strip)
_Free LED strip resources._ | +| esp\_err\_t | [**led\_strip\_refresh**](#function-led_strip_refresh) ([**led\_strip\_handle\_t**](#struct-led_strip_t) strip)
_Refresh memory colors to LEDs._ | +| esp\_err\_t | [**led\_strip\_set\_pixel**](#function-led_strip_set_pixel) ([**led\_strip\_handle\_t**](#struct-led_strip_t) strip, uint32\_t index, uint32\_t red, uint32\_t green, uint32\_t blue)
_Set RGB for a specific pixel._ | +| esp\_err\_t | [**led\_strip\_set\_pixel\_hsv**](#function-led_strip_set_pixel_hsv) ([**led\_strip\_handle\_t**](#struct-led_strip_t) strip, uint32\_t index, uint16\_t hue, uint8\_t saturation, uint8\_t value)
_Set HSV for a specific pixel._ | +| esp\_err\_t | [**led\_strip\_set\_pixel\_rgbw**](#function-led_strip_set_pixel_rgbw) ([**led\_strip\_handle\_t**](#struct-led_strip_t) strip, uint32\_t index, uint32\_t red, uint32\_t green, uint32\_t blue, uint32\_t white)
_Set RGBW for a specific pixel._ | + +## Functions Documentation + +### function `led_strip_clear` + +_Clear LED strip (turn off all LEDs)_ + +```c +esp_err_t led_strip_clear ( + led_strip_handle_t strip +) +``` + +**Parameters:** + +- `strip` LED strip + +**Returns:** + +- ESP\_OK: Clear LEDs successfully +- ESP\_FAIL: Clear LEDs failed because some other error occurred + +### function `led_strip_del` + +_Free LED strip resources._ + +```c +esp_err_t led_strip_del ( + led_strip_handle_t strip +) +``` + +**Parameters:** + +- `strip` LED strip + +**Returns:** + +- ESP\_OK: Free resources successfully +- ESP\_FAIL: Free resources failed because error occurred + +### function `led_strip_refresh` + +_Refresh memory colors to LEDs._ + +```c +esp_err_t led_strip_refresh ( + led_strip_handle_t strip +) +``` + +**Parameters:** + +- `strip` LED strip + +**Returns:** + +- ESP\_OK: Refresh successfully +- ESP\_FAIL: Refresh failed because some other error occurred + +**Note:** + +: After updating the LED colors in the memory, a following invocation of this API is needed to flush colors to strip. + +### function `led_strip_set_pixel` + +_Set RGB for a specific pixel._ + +```c +esp_err_t led_strip_set_pixel ( + led_strip_handle_t strip, + uint32_t index, + uint32_t red, + uint32_t green, + uint32_t blue +) +``` + +**Parameters:** + +- `strip` LED strip +- `index` index of pixel to set +- `red` red part of color +- `green` green part of color +- `blue` blue part of color + +**Returns:** + +- ESP\_OK: Set RGB for a specific pixel successfully +- ESP\_ERR\_INVALID\_ARG: Set RGB for a specific pixel failed because of invalid parameters +- ESP\_FAIL: Set RGB for a specific pixel failed because other error occurred + +### function `led_strip_set_pixel_hsv` + +_Set HSV for a specific pixel._ + +```c +esp_err_t led_strip_set_pixel_hsv ( + led_strip_handle_t strip, + uint32_t index, + uint16_t hue, + uint8_t saturation, + uint8_t value +) +``` + +**Parameters:** + +- `strip` LED strip +- `index` index of pixel to set +- `hue` hue part of color (0 - 360) +- `saturation` saturation part of color (0 - 255) +- `value` value part of color (0 - 255) + +**Returns:** + +- ESP\_OK: Set HSV color for a specific pixel successfully +- ESP\_ERR\_INVALID\_ARG: Set HSV color for a specific pixel failed because of an invalid argument +- ESP\_FAIL: Set HSV color for a specific pixel failed because other error occurred + +### function `led_strip_set_pixel_rgbw` + +_Set RGBW for a specific pixel._ + +```c +esp_err_t led_strip_set_pixel_rgbw ( + led_strip_handle_t strip, + uint32_t index, + uint32_t red, + uint32_t green, + uint32_t blue, + uint32_t white +) +``` + +**Note:** + +Only call this function if your led strip does have the white component (e.g. SK6812-RGBW) + +**Note:** + +Also see `led_strip_set_pixel` if you only want to specify the RGB part of the color and bypass the white component + +**Parameters:** + +- `strip` LED strip +- `index` index of pixel to set +- `red` red part of color +- `green` green part of color +- `blue` blue part of color +- `white` separate white component + +**Returns:** + +- ESP\_OK: Set RGBW color for a specific pixel successfully +- ESP\_ERR\_INVALID\_ARG: Set RGBW color for a specific pixel failed because of an invalid argument +- ESP\_FAIL: Set RGBW color for a specific pixel failed because other error occurred + +## File include/led_strip_rmt.h + +## Structures and Types + +| Type | Name | +| ---: | :--- | +| struct | [**led\_strip\_rmt\_config\_t**](#struct-led_strip_rmt_config_t)
_LED Strip RMT specific configuration._ | + +## Functions + +| Type | Name | +| ---: | :--- | +| esp\_err\_t | [**led\_strip\_new\_rmt\_device**](#function-led_strip_new_rmt_device) (const [**led\_strip\_config\_t**](#struct-led_strip_config_t) \*led\_config, const [**led\_strip\_rmt\_config\_t**](#struct-led_strip_rmt_config_t) \*rmt\_config, [**led\_strip\_handle\_t**](#struct-led_strip_t) \*ret\_strip)
_Create LED strip based on RMT TX channel._ | + +## Structures and Types Documentation + +### struct `led_strip_rmt_config_t` + +_LED Strip RMT specific configuration._ + +Variables: + +- rmt\_clock\_source\_t clk_src
RMT clock source + +- struct [**led\_strip\_rmt\_config\_t**](#struct-led_strip_rmt_config_t) flags
Extra driver flags + +- size\_t mem_block_symbols
How many RMT symbols can one RMT channel hold at one time. Set to 0 will fallback to use the default size. + +- uint32\_t resolution_hz
RMT tick resolution, if set to zero, a default resolution (10MHz) will be applied + +- uint32\_t with_dma
Use DMA to transmit data + +## Functions Documentation + +### function `led_strip_new_rmt_device` + +_Create LED strip based on RMT TX channel._ + +```c +esp_err_t led_strip_new_rmt_device ( + const led_strip_config_t *led_config, + const led_strip_rmt_config_t *rmt_config, + led_strip_handle_t *ret_strip +) +``` + +**Parameters:** + +- `led_config` LED strip configuration +- `rmt_config` RMT specific configuration +- `ret_strip` Returned LED strip handle + +**Returns:** + +- ESP\_OK: create LED strip handle successfully +- ESP\_ERR\_INVALID\_ARG: create LED strip handle failed because of invalid argument +- ESP\_ERR\_NO\_MEM: create LED strip handle failed because of out of memory +- ESP\_FAIL: create LED strip handle failed because some other error + +## File include/led_strip_spi.h + +## Structures and Types + +| Type | Name | +| ---: | :--- | +| struct | [**led\_strip\_spi\_config\_t**](#struct-led_strip_spi_config_t)
_LED Strip SPI specific configuration._ | + +## Functions + +| Type | Name | +| ---: | :--- | +| esp\_err\_t | [**led\_strip\_new\_spi\_device**](#function-led_strip_new_spi_device) (const [**led\_strip\_config\_t**](#struct-led_strip_config_t) \*led\_config, const [**led\_strip\_spi\_config\_t**](#struct-led_strip_spi_config_t) \*spi\_config, [**led\_strip\_handle\_t**](#struct-led_strip_t) \*ret\_strip)
_Create LED strip based on SPI MOSI channel._ | + +## Structures and Types Documentation + +### struct `led_strip_spi_config_t` + +_LED Strip SPI specific configuration._ + +Variables: + +- spi\_clock\_source\_t clk_src
SPI clock source + +- struct [**led\_strip\_spi\_config\_t**](#struct-led_strip_spi_config_t) flags
Extra driver flags + +- spi\_host\_device\_t spi_bus
SPI bus ID. Which buses are available depends on the specific chip + +- uint32\_t with_dma
Use DMA to transmit data + +## Functions Documentation + +### function `led_strip_new_spi_device` + +_Create LED strip based on SPI MOSI channel._ + +```c +esp_err_t led_strip_new_spi_device ( + const led_strip_config_t *led_config, + const led_strip_spi_config_t *spi_config, + led_strip_handle_t *ret_strip +) +``` + +**Note:** + +Although only the MOSI line is used for generating the signal, the whole SPI bus can't be used for other purposes. + +**Parameters:** + +- `led_config` LED strip configuration +- `spi_config` SPI specific configuration +- `ret_strip` Returned LED strip handle + +**Returns:** + +- ESP\_OK: create LED strip handle successfully +- ESP\_ERR\_INVALID\_ARG: create LED strip handle failed because of invalid argument +- ESP\_ERR\_NOT\_SUPPORTED: create LED strip handle failed because of unsupported configuration +- ESP\_ERR\_NO\_MEM: create LED strip handle failed because of out of memory +- ESP\_FAIL: create LED strip handle failed because some other error + +## File include/led_strip_types.h + +## Structures and Types + +| Type | Name | +| ---: | :--- | +| enum | [**led\_model\_t**](#enum-led_model_t)
_LED strip model._ | +| enum | [**led\_pixel\_format\_t**](#enum-led_pixel_format_t)
_LED strip pixel format._ | +| struct | [**led\_strip\_config\_t**](#struct-led_strip_config_t)
_LED Strip Configuration._ | +| typedef struct [**led\_strip\_t**](#struct-led_strip_t) \* | [**led\_strip\_handle\_t**](#typedef-led_strip_handle_t)
_LED strip handle._ | + +## Structures and Types Documentation + +### enum `led_model_t` + +_LED strip model._ + +```c +enum led_model_t { + LED_MODEL_WS2812, + LED_MODEL_SK6812, + LED_MODEL_INVALID +}; +``` + +**Note:** + +Different led model may have different timing parameters, so we need to distinguish them. + +### enum `led_pixel_format_t` + +_LED strip pixel format._ + +```c +enum led_pixel_format_t { + LED_PIXEL_FORMAT_GRB, + LED_PIXEL_FORMAT_GRBW, + LED_PIXEL_FORMAT_INVALID +}; +``` + +### struct `led_strip_config_t` + +_LED Strip Configuration._ + +Variables: + +- struct [**led\_strip\_config\_t**](#struct-led_strip_config_t) flags
Extra driver flags + +- uint32\_t invert_out
Invert output signal + +- led\_model\_t led_model
LED model + +- led\_pixel\_format\_t led_pixel_format
LED pixel format + +- uint32\_t max_leds
Maximum LEDs in a single strip + +- int strip_gpio_num
GPIO number that used by LED strip + +### typedef `led_strip_handle_t` + +_LED strip handle._ + +```c +typedef struct led_strip_t* led_strip_handle_t; +``` + +## File interface/led_strip_interface.h + +## Structures and Types + +| Type | Name | +| ---: | :--- | +| struct | [**led\_strip\_t**](#struct-led_strip_t)
_LED strip interface definition._ | +| typedef struct [**led\_strip\_t**](#struct-led_strip_t) | [**led\_strip\_t**](#typedef-led_strip_t)
| + +## Structures and Types Documentation + +### struct `led_strip_t` + +_LED strip interface definition._ + +Variables: + +- esp\_err\_t(\* clear
_Clear LED strip (turn off all LEDs)_
**Parameters:** + +- `strip` LED strip +- `timeout_ms` timeout value for clearing task + +**Returns:** + +- ESP\_OK: Clear LEDs successfully +- ESP\_FAIL: Clear LEDs failed because some other error occurred + +- esp\_err\_t(\* del
_Free LED strip resources._
**Parameters:** + +- `strip` LED strip + +**Returns:** + +- ESP\_OK: Free resources successfully +- ESP\_FAIL: Free resources failed because error occurred + +- esp\_err\_t(\* refresh
_Refresh memory colors to LEDs._
**Parameters:** + +- `strip` LED strip +- `timeout_ms` timeout value for refreshing task + +**Returns:** + +- ESP\_OK: Refresh successfully +- ESP\_FAIL: Refresh failed because some other error occurred + +**Note:** + +: After updating the LED colors in the memory, a following invocation of this API is needed to flush colors to strip. + +- esp\_err\_t(\* set_pixel
_Set RGB for a specific pixel._
**Parameters:** + +- `strip` LED strip +- `index` index of pixel to set +- `red` red part of color +- `green` green part of color +- `blue` blue part of color + +**Returns:** + +- ESP\_OK: Set RGB for a specific pixel successfully +- ESP\_ERR\_INVALID\_ARG: Set RGB for a specific pixel failed because of invalid parameters +- ESP\_FAIL: Set RGB for a specific pixel failed because other error occurred + +- esp\_err\_t(\* set_pixel_rgbw
_Set RGBW for a specific pixel. Similar to_ `set_pixel`_but also set the white component._
**Parameters:** + +- `strip` LED strip +- `index` index of pixel to set +- `red` red part of color +- `green` green part of color +- `blue` blue part of color +- `white` separate white component + +**Returns:** + +- ESP\_OK: Set RGBW color for a specific pixel successfully +- ESP\_ERR\_INVALID\_ARG: Set RGBW color for a specific pixel failed because of an invalid argument +- ESP\_FAIL: Set RGBW color for a specific pixel failed because other error occurred + +### typedef `led_strip_t` + +```c +typedef struct led_strip_t led_strip_t; +``` + +Type of LED strip diff --git a/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/CMakeLists.txt b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/CMakeLists.txt new file mode 100644 index 000000000..923c46310 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/CMakeLists.txt @@ -0,0 +1,9 @@ +# For more information about build system see +# https://docs.espressif.com/projects/esp-idf/en/latest/api-guides/build-system.html +# The following five lines of boilerplate have to be in your project's +# CMakeLists in this exact order for cmake to work correctly +cmake_minimum_required(VERSION 3.16) + +set(IDF_TARGET "esp32s3") +include($ENV{IDF_PATH}/tools/cmake/project.cmake) +project(led_strip_rmt_ws2812) diff --git a/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/README.md b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/README.md new file mode 100644 index 000000000..ad52235d5 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/README.md @@ -0,0 +1,31 @@ +# LED Strip Example (RMT backend + WS2812) + +This example demonstrates how to blink the WS2812 LED using the [led_strip](https://components.espressif.com/component/espressif/led_strip) component. + +## How to Use Example + +### Hardware Required + +* A development board with Espressif SoC +* A USB cable for Power supply and programming +* WS2812 LED strip + +### Configure the Example + +Before project configuration and build, be sure to set the correct chip target using `idf.py set-target `. Then assign the proper GPIO in the [source file](main/led_strip_rmt_ws2812_main.c). If your led strip has multiple LEDs, don't forget update the number. + +### Build and Flash + +Run `idf.py -p PORT build flash monitor` to build, flash and monitor the project. + +(To exit the serial monitor, type ``Ctrl-]``.) + +See the [Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects. + +## Example Output + +```text +I (299) gpio: GPIO[8]| InputEn: 0| OutputEn: 1| OpenDrain: 0| Pullup: 1| Pulldown: 0| Intr:0 +I (309) example: Created LED strip object with RMT backend +I (309) example: Start blinking LED strip +``` diff --git a/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/dependencies.lock b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/dependencies.lock new file mode 100644 index 000000000..97840a153 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/dependencies.lock @@ -0,0 +1,15 @@ +dependencies: + espressif/led_strip: + component_hash: null + source: + path: /home/hathach/code/idf-extra-components/led_strip + type: local + version: 2.5.2 + idf: + component_hash: null + source: + type: idf + version: 5.1.1 +manifest_hash: 47d47762be26168b388cb0e6cbfee6b22c68d630ebf4b27a49c47c4c54191590 +target: esp32s3 +version: 1.0.0 diff --git a/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/CMakeLists.txt b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/CMakeLists.txt new file mode 100644 index 000000000..37b9c1458 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/CMakeLists.txt @@ -0,0 +1,2 @@ +idf_component_register(SRCS "led_strip_rmt_ws2812_main.c" + INCLUDE_DIRS ".") diff --git a/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/idf_component.yml b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/idf_component.yml new file mode 100644 index 000000000..916c366c7 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/idf_component.yml @@ -0,0 +1,5 @@ +## IDF Component Manager Manifest File +dependencies: + espressif/led_strip: + version: '^2' + override_path: '../../../' diff --git a/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/led_strip_rmt_ws2812_main.c b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/led_strip_rmt_ws2812_main.c new file mode 100644 index 000000000..4b20a5958 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/examples/led_strip_rmt_ws2812/main/led_strip_rmt_ws2812_main.c @@ -0,0 +1,75 @@ +/* + * SPDX-FileCopyrightText: 2023 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Unlicense OR CC0-1.0 + */ +#include +#include "freertos/FreeRTOS.h" +#include "freertos/task.h" +#include "led_strip.h" +#include "esp_log.h" +#include "esp_err.h" + +// GPIO assignment +#define LED_STRIP_BLINK_GPIO 48 +// Numbers of the LED in the strip +#define LED_STRIP_LED_NUMBERS 1 +// 10MHz resolution, 1 tick = 0.1us (led strip needs a high resolution) +#define LED_STRIP_RMT_RES_HZ (10 * 1000 * 1000) + +static const char *TAG = "example"; + +led_strip_handle_t configure_led(void) +{ + // LED strip general initialization, according to your led board design + led_strip_config_t strip_config = { + .strip_gpio_num = LED_STRIP_BLINK_GPIO, // The GPIO that connected to the LED strip's data line + .max_leds = LED_STRIP_LED_NUMBERS, // The number of LEDs in the strip, + .led_pixel_format = LED_PIXEL_FORMAT_GRB, // Pixel format of your LED strip + .led_model = LED_MODEL_WS2812, // LED strip model + .flags.invert_out = false, // whether to invert the output signal + }; + + // LED strip backend configuration: RMT + led_strip_rmt_config_t rmt_config = { +#if ESP_IDF_VERSION < ESP_IDF_VERSION_VAL(5, 0, 0) + .rmt_channel = 0, +#else + .clk_src = RMT_CLK_SRC_DEFAULT, // different clock source can lead to different power consumption + .resolution_hz = LED_STRIP_RMT_RES_HZ, // RMT counter clock frequency + .flags.with_dma = false, // DMA feature is available on ESP target like ESP32-S3 +#endif + }; + + // LED Strip object handle + led_strip_handle_t led_strip; + ESP_ERROR_CHECK(led_strip_new_rmt_device(&strip_config, &rmt_config, &led_strip)); + ESP_LOGI(TAG, "Created LED strip object with RMT backend"); + return led_strip; +} + +void app_main(void) +{ + led_strip_handle_t led_strip = configure_led(); + bool led_on_off = false; + + ESP_LOGI(TAG, "Start blinking LED strip"); + while (1) { + if (led_on_off) { + /* Set the LED pixel using RGB from 0 (0%) to 255 (100%) for each color */ + for (int i = 0; i < LED_STRIP_LED_NUMBERS; i++) { + ESP_ERROR_CHECK(led_strip_set_pixel(led_strip, i, 5, 5, 5)); + } + /* Refresh the strip to send data */ + ESP_ERROR_CHECK(led_strip_refresh(led_strip)); + ESP_LOGI(TAG, "LED ON!"); + } else { + /* Set all LED off to clear all pixels */ + ESP_ERROR_CHECK(led_strip_clear(led_strip)); + ESP_LOGI(TAG, "LED OFF!"); + } + + led_on_off = !led_on_off; + vTaskDelay(pdMS_TO_TICKS(500)); + } +} diff --git a/hw/bsp/espressif/components/led_strip/idf_component.yml b/hw/bsp/espressif/components/led_strip/idf_component.yml new file mode 100644 index 000000000..1fd9b83ee --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/idf_component.yml @@ -0,0 +1,5 @@ +version: "2.5.2" +description: Driver for Addressable LED Strip (WS2812, etc) +url: https://github.com/espressif/idf-extra-components/tree/master/led_strip +dependencies: + idf: ">=4.4" diff --git a/hw/bsp/espressif/components/led_strip/include/led_strip.h b/hw/bsp/espressif/components/led_strip/include/led_strip.h index a9dffc325..38711744a 100644 --- a/hw/bsp/espressif/components/led_strip/include/led_strip.h +++ b/hw/bsp/espressif/components/led_strip/include/led_strip.h @@ -1,125 +1,110 @@ -// Copyright 2019 Espressif Systems (Shanghai) PTE LTD -// -// Licensed under the Apache License, Version 2.0 (the "License"); -// you may not use this file except in compliance with the License. -// You may obtain a copy of the License at -// -// http://www.apache.org/licenses/LICENSE-2.0 -// -// Unless required by applicable law or agreed to in writing, software -// distributed under the License is distributed on an "AS IS" BASIS, -// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -// See the License for the specific language governing permissions and -// limitations under the License. +/* + * SPDX-FileCopyrightText: 2022-2023 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ #pragma once +#include +#include "esp_err.h" +#include "led_strip_rmt.h" +#include "esp_idf_version.h" + +#if ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 1, 0) +#include "led_strip_spi.h" +#endif + #ifdef __cplusplus extern "C" { #endif -#include "esp_err.h" - /** -* @brief LED Strip Type -* -*/ -typedef struct led_strip_s led_strip_t; + * @brief Set RGB for a specific pixel + * + * @param strip: LED strip + * @param index: index of pixel to set + * @param red: red part of color + * @param green: green part of color + * @param blue: blue part of color + * + * @return + * - ESP_OK: Set RGB for a specific pixel successfully + * - ESP_ERR_INVALID_ARG: Set RGB for a specific pixel failed because of invalid parameters + * - ESP_FAIL: Set RGB for a specific pixel failed because other error occurred + */ +esp_err_t led_strip_set_pixel(led_strip_handle_t strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue); /** -* @brief LED Strip Device Type -* -*/ -typedef void *led_strip_dev_t; + * @brief Set RGBW for a specific pixel + * + * @note Only call this function if your led strip does have the white component (e.g. SK6812-RGBW) + * @note Also see `led_strip_set_pixel` if you only want to specify the RGB part of the color and bypass the white component + * + * @param strip: LED strip + * @param index: index of pixel to set + * @param red: red part of color + * @param green: green part of color + * @param blue: blue part of color + * @param white: separate white component + * + * @return + * - ESP_OK: Set RGBW color for a specific pixel successfully + * - ESP_ERR_INVALID_ARG: Set RGBW color for a specific pixel failed because of an invalid argument + * - ESP_FAIL: Set RGBW color for a specific pixel failed because other error occurred + */ +esp_err_t led_strip_set_pixel_rgbw(led_strip_handle_t strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue, uint32_t white); /** -* @brief Declare of LED Strip Type -* -*/ -struct led_strip_s { - /** - * @brief Set RGB for a specific pixel - * - * @param strip: LED strip - * @param index: index of pixel to set - * @param red: red part of color - * @param green: green part of color - * @param blue: blue part of color - * - * @return - * - ESP_OK: Set RGB for a specific pixel successfully - * - ESP_ERR_INVALID_ARG: Set RGB for a specific pixel failed because of invalid parameters - * - ESP_FAIL: Set RGB for a specific pixel failed because other error occurred - */ - esp_err_t (*set_pixel)(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue); - - /** - * @brief Refresh memory colors to LEDs - * - * @param strip: LED strip - * @param timeout_ms: timeout value for refreshing task - * - * @return - * - ESP_OK: Refresh successfully - * - ESP_ERR_TIMEOUT: Refresh failed because of timeout - * - ESP_FAIL: Refresh failed because some other error occurred - * - * @note: - * After updating the LED colors in the memory, a following invocation of this API is needed to flush colors to strip. - */ - esp_err_t (*refresh)(led_strip_t *strip, uint32_t timeout_ms); - - /** - * @brief Clear LED strip (turn off all LEDs) - * - * @param strip: LED strip - * @param timeout_ms: timeout value for clearing task - * - * @return - * - ESP_OK: Clear LEDs successfully - * - ESP_ERR_TIMEOUT: Clear LEDs failed because of timeout - * - ESP_FAIL: Clear LEDs failed because some other error occurred - */ - esp_err_t (*clear)(led_strip_t *strip, uint32_t timeout_ms); - - /** - * @brief Free LED strip resources - * - * @param strip: LED strip - * - * @return - * - ESP_OK: Free resources successfully - * - ESP_FAIL: Free resources failed because error occurred - */ - esp_err_t (*del)(led_strip_t *strip); -}; + * @brief Set HSV for a specific pixel + * + * @param strip: LED strip + * @param index: index of pixel to set + * @param hue: hue part of color (0 - 360) + * @param saturation: saturation part of color (0 - 255) + * @param value: value part of color (0 - 255) + * + * @return + * - ESP_OK: Set HSV color for a specific pixel successfully + * - ESP_ERR_INVALID_ARG: Set HSV color for a specific pixel failed because of an invalid argument + * - ESP_FAIL: Set HSV color for a specific pixel failed because other error occurred + */ +esp_err_t led_strip_set_pixel_hsv(led_strip_handle_t strip, uint32_t index, uint16_t hue, uint8_t saturation, uint8_t value); /** -* @brief LED Strip Configuration Type -* -*/ -typedef struct { - uint32_t max_leds; /*!< Maximum LEDs in a single strip */ - led_strip_dev_t dev; /*!< LED strip device (e.g. RMT channel, PWM channel, etc) */ -} led_strip_config_t; + * @brief Refresh memory colors to LEDs + * + * @param strip: LED strip + * + * @return + * - ESP_OK: Refresh successfully + * - ESP_FAIL: Refresh failed because some other error occurred + * + * @note: + * After updating the LED colors in the memory, a following invocation of this API is needed to flush colors to strip. + */ +esp_err_t led_strip_refresh(led_strip_handle_t strip); /** - * @brief Default configuration for LED strip + * @brief Clear LED strip (turn off all LEDs) + * + * @param strip: LED strip * + * @return + * - ESP_OK: Clear LEDs successfully + * - ESP_FAIL: Clear LEDs failed because some other error occurred */ -#define LED_STRIP_DEFAULT_CONFIG(number, dev_hdl) \ - { \ - .max_leds = number, \ - .dev = dev_hdl, \ - } +esp_err_t led_strip_clear(led_strip_handle_t strip); /** -* @brief Install a new ws2812 driver (based on RMT peripheral) -* -* @param config: LED strip configuration -* @return -* LED strip instance or NULL -*/ -led_strip_t *led_strip_new_rmt_ws2812(const led_strip_config_t *config); + * @brief Free LED strip resources + * + * @param strip: LED strip + * + * @return + * - ESP_OK: Free resources successfully + * - ESP_FAIL: Free resources failed because error occurred + */ +esp_err_t led_strip_del(led_strip_handle_t strip); #ifdef __cplusplus } diff --git a/hw/bsp/espressif/components/led_strip/include/led_strip_rmt.h b/hw/bsp/espressif/components/led_strip/include/led_strip_rmt.h new file mode 100644 index 000000000..b575aeaba --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/include/led_strip_rmt.h @@ -0,0 +1,53 @@ +/* + * SPDX-FileCopyrightText: 2022-2023 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ +#pragma once + +#include +#include "esp_err.h" +#include "led_strip_types.h" +#include "esp_idf_version.h" + +#if ESP_IDF_VERSION >= ESP_IDF_VERSION_VAL(5, 0, 0) +#include "driver/rmt_types.h" +#endif + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * @brief LED Strip RMT specific configuration + */ +typedef struct { +#if ESP_IDF_VERSION < ESP_IDF_VERSION_VAL(5, 0, 0) + uint8_t rmt_channel; /*!< Specify the channel number, the legacy RMT driver doesn't support channel allocator */ +#else // new driver supports specify the clock source and clock resolution + rmt_clock_source_t clk_src; /*!< RMT clock source */ + uint32_t resolution_hz; /*!< RMT tick resolution, if set to zero, a default resolution (10MHz) will be applied */ +#endif + size_t mem_block_symbols; /*!< How many RMT symbols can one RMT channel hold at one time. Set to 0 will fallback to use the default size. */ + struct { + uint32_t with_dma: 1; /*!< Use DMA to transmit data */ + } flags; /*!< Extra driver flags */ +} led_strip_rmt_config_t; + +/** + * @brief Create LED strip based on RMT TX channel + * + * @param led_config LED strip configuration + * @param rmt_config RMT specific configuration + * @param ret_strip Returned LED strip handle + * @return + * - ESP_OK: create LED strip handle successfully + * - ESP_ERR_INVALID_ARG: create LED strip handle failed because of invalid argument + * - ESP_ERR_NO_MEM: create LED strip handle failed because of out of memory + * - ESP_FAIL: create LED strip handle failed because some other error + */ +esp_err_t led_strip_new_rmt_device(const led_strip_config_t *led_config, const led_strip_rmt_config_t *rmt_config, led_strip_handle_t *ret_strip); + +#ifdef __cplusplus +} +#endif diff --git a/hw/bsp/espressif/components/led_strip/include/led_strip_spi.h b/hw/bsp/espressif/components/led_strip/include/led_strip_spi.h new file mode 100644 index 000000000..eb3524936 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/include/led_strip_spi.h @@ -0,0 +1,46 @@ +/* + * SPDX-FileCopyrightText: 2022-2023 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ +#pragma once + +#include +#include "esp_err.h" +#include "driver/spi_master.h" +#include "led_strip_types.h" + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * @brief LED Strip SPI specific configuration + */ +typedef struct { + spi_clock_source_t clk_src; /*!< SPI clock source */ + spi_host_device_t spi_bus; /*!< SPI bus ID. Which buses are available depends on the specific chip */ + struct { + uint32_t with_dma: 1; /*!< Use DMA to transmit data */ + } flags; /*!< Extra driver flags */ +} led_strip_spi_config_t; + +/** + * @brief Create LED strip based on SPI MOSI channel + * @note Although only the MOSI line is used for generating the signal, the whole SPI bus can't be used for other purposes. + * + * @param led_config LED strip configuration + * @param spi_config SPI specific configuration + * @param ret_strip Returned LED strip handle + * @return + * - ESP_OK: create LED strip handle successfully + * - ESP_ERR_INVALID_ARG: create LED strip handle failed because of invalid argument + * - ESP_ERR_NOT_SUPPORTED: create LED strip handle failed because of unsupported configuration + * - ESP_ERR_NO_MEM: create LED strip handle failed because of out of memory + * - ESP_FAIL: create LED strip handle failed because some other error + */ +esp_err_t led_strip_new_spi_device(const led_strip_config_t *led_config, const led_strip_spi_config_t *spi_config, led_strip_handle_t *ret_strip); + +#ifdef __cplusplus +} +#endif diff --git a/hw/bsp/espressif/components/led_strip/include/led_strip_types.h b/hw/bsp/espressif/components/led_strip/include/led_strip_types.h new file mode 100644 index 000000000..691f0bc39 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/include/led_strip_types.h @@ -0,0 +1,54 @@ +/* + * SPDX-FileCopyrightText: 2022-2023 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ +#pragma once + +#include + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * @brief LED strip pixel format + */ +typedef enum { + LED_PIXEL_FORMAT_GRB, /*!< Pixel format: GRB */ + LED_PIXEL_FORMAT_GRBW, /*!< Pixel format: GRBW */ + LED_PIXEL_FORMAT_INVALID /*!< Invalid pixel format */ +} led_pixel_format_t; + +/** + * @brief LED strip model + * @note Different led model may have different timing parameters, so we need to distinguish them. + */ +typedef enum { + LED_MODEL_WS2812, /*!< LED strip model: WS2812 */ + LED_MODEL_SK6812, /*!< LED strip model: SK6812 */ + LED_MODEL_INVALID /*!< Invalid LED strip model */ +} led_model_t; + +/** + * @brief LED strip handle + */ +typedef struct led_strip_t *led_strip_handle_t; + +/** + * @brief LED Strip Configuration + */ +typedef struct { + int strip_gpio_num; /*!< GPIO number that used by LED strip */ + uint32_t max_leds; /*!< Maximum LEDs in a single strip */ + led_pixel_format_t led_pixel_format; /*!< LED pixel format */ + led_model_t led_model; /*!< LED model */ + + struct { + uint32_t invert_out: 1; /*!< Invert output signal */ + } flags; /*!< Extra driver flags */ +} led_strip_config_t; + +#ifdef __cplusplus +} +#endif diff --git a/hw/bsp/espressif/components/led_strip/interface/led_strip_interface.h b/hw/bsp/espressif/components/led_strip/interface/led_strip_interface.h new file mode 100644 index 000000000..3de4c2715 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/interface/led_strip_interface.h @@ -0,0 +1,95 @@ +/* + * SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ +#pragma once + +#include +#include "esp_err.h" + +#ifdef __cplusplus +extern "C" { +#endif + +typedef struct led_strip_t led_strip_t; /*!< Type of LED strip */ + +/** + * @brief LED strip interface definition + */ +struct led_strip_t { + /** + * @brief Set RGB for a specific pixel + * + * @param strip: LED strip + * @param index: index of pixel to set + * @param red: red part of color + * @param green: green part of color + * @param blue: blue part of color + * + * @return + * - ESP_OK: Set RGB for a specific pixel successfully + * - ESP_ERR_INVALID_ARG: Set RGB for a specific pixel failed because of invalid parameters + * - ESP_FAIL: Set RGB for a specific pixel failed because other error occurred + */ + esp_err_t (*set_pixel)(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue); + + /** + * @brief Set RGBW for a specific pixel. Similar to `set_pixel` but also set the white component + * + * @param strip: LED strip + * @param index: index of pixel to set + * @param red: red part of color + * @param green: green part of color + * @param blue: blue part of color + * @param white: separate white component + * + * @return + * - ESP_OK: Set RGBW color for a specific pixel successfully + * - ESP_ERR_INVALID_ARG: Set RGBW color for a specific pixel failed because of an invalid argument + * - ESP_FAIL: Set RGBW color for a specific pixel failed because other error occurred + */ + esp_err_t (*set_pixel_rgbw)(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue, uint32_t white); + + /** + * @brief Refresh memory colors to LEDs + * + * @param strip: LED strip + * @param timeout_ms: timeout value for refreshing task + * + * @return + * - ESP_OK: Refresh successfully + * - ESP_FAIL: Refresh failed because some other error occurred + * + * @note: + * After updating the LED colors in the memory, a following invocation of this API is needed to flush colors to strip. + */ + esp_err_t (*refresh)(led_strip_t *strip); + + /** + * @brief Clear LED strip (turn off all LEDs) + * + * @param strip: LED strip + * @param timeout_ms: timeout value for clearing task + * + * @return + * - ESP_OK: Clear LEDs successfully + * - ESP_FAIL: Clear LEDs failed because some other error occurred + */ + esp_err_t (*clear)(led_strip_t *strip); + + /** + * @brief Free LED strip resources + * + * @param strip: LED strip + * + * @return + * - ESP_OK: Free resources successfully + * - ESP_FAIL: Free resources failed because error occurred + */ + esp_err_t (*del)(led_strip_t *strip); +}; + +#ifdef __cplusplus +} +#endif diff --git a/hw/bsp/espressif/components/led_strip/src/led_strip_api.c b/hw/bsp/espressif/components/led_strip/src/led_strip_api.c new file mode 100644 index 000000000..6eb86b8f1 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/src/led_strip_api.c @@ -0,0 +1,94 @@ +/* + * SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ +#include "esp_log.h" +#include "esp_check.h" +#include "led_strip.h" +#include "led_strip_interface.h" + +static const char *TAG = "led_strip"; + +esp_err_t led_strip_set_pixel(led_strip_handle_t strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue) +{ + ESP_RETURN_ON_FALSE(strip, ESP_ERR_INVALID_ARG, TAG, "invalid argument"); + return strip->set_pixel(strip, index, red, green, blue); +} + +esp_err_t led_strip_set_pixel_hsv(led_strip_handle_t strip, uint32_t index, uint16_t hue, uint8_t saturation, uint8_t value) +{ + ESP_RETURN_ON_FALSE(strip, ESP_ERR_INVALID_ARG, TAG, "invalid argument"); + + uint32_t red = 0; + uint32_t green = 0; + uint32_t blue = 0; + + uint32_t rgb_max = value; + uint32_t rgb_min = rgb_max * (255 - saturation) / 255.0f; + + uint32_t i = hue / 60; + uint32_t diff = hue % 60; + + // RGB adjustment amount by hue + uint32_t rgb_adj = (rgb_max - rgb_min) * diff / 60; + + switch (i) { + case 0: + red = rgb_max; + green = rgb_min + rgb_adj; + blue = rgb_min; + break; + case 1: + red = rgb_max - rgb_adj; + green = rgb_max; + blue = rgb_min; + break; + case 2: + red = rgb_min; + green = rgb_max; + blue = rgb_min + rgb_adj; + break; + case 3: + red = rgb_min; + green = rgb_max - rgb_adj; + blue = rgb_max; + break; + case 4: + red = rgb_min + rgb_adj; + green = rgb_min; + blue = rgb_max; + break; + default: + red = rgb_max; + green = rgb_min; + blue = rgb_max - rgb_adj; + break; + } + + return strip->set_pixel(strip, index, red, green, blue); +} + +esp_err_t led_strip_set_pixel_rgbw(led_strip_handle_t strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue, uint32_t white) +{ + ESP_RETURN_ON_FALSE(strip, ESP_ERR_INVALID_ARG, TAG, "invalid argument"); + return strip->set_pixel_rgbw(strip, index, red, green, blue, white); +} + +esp_err_t led_strip_refresh(led_strip_handle_t strip) +{ + ESP_RETURN_ON_FALSE(strip, ESP_ERR_INVALID_ARG, TAG, "invalid argument"); + return strip->refresh(strip); +} + +esp_err_t led_strip_clear(led_strip_handle_t strip) +{ + ESP_RETURN_ON_FALSE(strip, ESP_ERR_INVALID_ARG, TAG, "invalid argument"); + return strip->clear(strip); +} + +esp_err_t led_strip_del(led_strip_handle_t strip) +{ + ESP_RETURN_ON_FALSE(strip, ESP_ERR_INVALID_ARG, TAG, "invalid argument"); + return strip->del(strip); +} diff --git a/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_dev.c b/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_dev.c new file mode 100644 index 000000000..1cbf0e45a --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_dev.c @@ -0,0 +1,164 @@ +/* + * SPDX-FileCopyrightText: 2022-2023 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ +#include +#include +#include +#include "esp_log.h" +#include "esp_check.h" +#include "driver/rmt_tx.h" +#include "led_strip.h" +#include "led_strip_interface.h" +#include "led_strip_rmt_encoder.h" + +#define LED_STRIP_RMT_DEFAULT_RESOLUTION 10000000 // 10MHz resolution +#define LED_STRIP_RMT_DEFAULT_TRANS_QUEUE_SIZE 4 +// the memory size of each RMT channel, in words (4 bytes) +#if CONFIG_IDF_TARGET_ESP32 || CONFIG_IDF_TARGET_ESP32S2 +#define LED_STRIP_RMT_DEFAULT_MEM_BLOCK_SYMBOLS 64 +#else +#define LED_STRIP_RMT_DEFAULT_MEM_BLOCK_SYMBOLS 48 +#endif + +static const char *TAG = "led_strip_rmt"; + +typedef struct { + led_strip_t base; + rmt_channel_handle_t rmt_chan; + rmt_encoder_handle_t strip_encoder; + uint32_t strip_len; + uint8_t bytes_per_pixel; + uint8_t pixel_buf[]; +} led_strip_rmt_obj; + +static esp_err_t led_strip_rmt_set_pixel(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue) +{ + led_strip_rmt_obj *rmt_strip = __containerof(strip, led_strip_rmt_obj, base); + ESP_RETURN_ON_FALSE(index < rmt_strip->strip_len, ESP_ERR_INVALID_ARG, TAG, "index out of maximum number of LEDs"); + uint32_t start = index * rmt_strip->bytes_per_pixel; + // In thr order of GRB, as LED strip like WS2812 sends out pixels in this order + rmt_strip->pixel_buf[start + 0] = green & 0xFF; + rmt_strip->pixel_buf[start + 1] = red & 0xFF; + rmt_strip->pixel_buf[start + 2] = blue & 0xFF; + if (rmt_strip->bytes_per_pixel > 3) { + rmt_strip->pixel_buf[start + 3] = 0; + } + return ESP_OK; +} + +static esp_err_t led_strip_rmt_set_pixel_rgbw(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue, uint32_t white) +{ + led_strip_rmt_obj *rmt_strip = __containerof(strip, led_strip_rmt_obj, base); + ESP_RETURN_ON_FALSE(index < rmt_strip->strip_len, ESP_ERR_INVALID_ARG, TAG, "index out of maximum number of LEDs"); + ESP_RETURN_ON_FALSE(rmt_strip->bytes_per_pixel == 4, ESP_ERR_INVALID_ARG, TAG, "wrong LED pixel format, expected 4 bytes per pixel"); + uint8_t *buf_start = rmt_strip->pixel_buf + index * 4; + // SK6812 component order is GRBW + *buf_start = green & 0xFF; + *++buf_start = red & 0xFF; + *++buf_start = blue & 0xFF; + *++buf_start = white & 0xFF; + return ESP_OK; +} + +static esp_err_t led_strip_rmt_refresh(led_strip_t *strip) +{ + led_strip_rmt_obj *rmt_strip = __containerof(strip, led_strip_rmt_obj, base); + rmt_transmit_config_t tx_conf = { + .loop_count = 0, + }; + + ESP_RETURN_ON_ERROR(rmt_enable(rmt_strip->rmt_chan), TAG, "enable RMT channel failed"); + ESP_RETURN_ON_ERROR(rmt_transmit(rmt_strip->rmt_chan, rmt_strip->strip_encoder, rmt_strip->pixel_buf, + rmt_strip->strip_len * rmt_strip->bytes_per_pixel, &tx_conf), TAG, "transmit pixels by RMT failed"); + ESP_RETURN_ON_ERROR(rmt_tx_wait_all_done(rmt_strip->rmt_chan, -1), TAG, "flush RMT channel failed"); + ESP_RETURN_ON_ERROR(rmt_disable(rmt_strip->rmt_chan), TAG, "disable RMT channel failed"); + return ESP_OK; +} + +static esp_err_t led_strip_rmt_clear(led_strip_t *strip) +{ + led_strip_rmt_obj *rmt_strip = __containerof(strip, led_strip_rmt_obj, base); + // Write zero to turn off all leds + memset(rmt_strip->pixel_buf, 0, rmt_strip->strip_len * rmt_strip->bytes_per_pixel); + return led_strip_rmt_refresh(strip); +} + +static esp_err_t led_strip_rmt_del(led_strip_t *strip) +{ + led_strip_rmt_obj *rmt_strip = __containerof(strip, led_strip_rmt_obj, base); + ESP_RETURN_ON_ERROR(rmt_del_channel(rmt_strip->rmt_chan), TAG, "delete RMT channel failed"); + ESP_RETURN_ON_ERROR(rmt_del_encoder(rmt_strip->strip_encoder), TAG, "delete strip encoder failed"); + free(rmt_strip); + return ESP_OK; +} + +esp_err_t led_strip_new_rmt_device(const led_strip_config_t *led_config, const led_strip_rmt_config_t *rmt_config, led_strip_handle_t *ret_strip) +{ + led_strip_rmt_obj *rmt_strip = NULL; + esp_err_t ret = ESP_OK; + ESP_GOTO_ON_FALSE(led_config && rmt_config && ret_strip, ESP_ERR_INVALID_ARG, err, TAG, "invalid argument"); + ESP_GOTO_ON_FALSE(led_config->led_pixel_format < LED_PIXEL_FORMAT_INVALID, ESP_ERR_INVALID_ARG, err, TAG, "invalid led_pixel_format"); + uint8_t bytes_per_pixel = 3; + if (led_config->led_pixel_format == LED_PIXEL_FORMAT_GRBW) { + bytes_per_pixel = 4; + } else if (led_config->led_pixel_format == LED_PIXEL_FORMAT_GRB) { + bytes_per_pixel = 3; + } else { + assert(false); + } + rmt_strip = calloc(1, sizeof(led_strip_rmt_obj) + led_config->max_leds * bytes_per_pixel); + ESP_GOTO_ON_FALSE(rmt_strip, ESP_ERR_NO_MEM, err, TAG, "no mem for rmt strip"); + uint32_t resolution = rmt_config->resolution_hz ? rmt_config->resolution_hz : LED_STRIP_RMT_DEFAULT_RESOLUTION; + + // for backward compatibility, if the user does not set the clk_src, use the default value + rmt_clock_source_t clk_src = RMT_CLK_SRC_DEFAULT; + if (rmt_config->clk_src) { + clk_src = rmt_config->clk_src; + } + size_t mem_block_symbols = LED_STRIP_RMT_DEFAULT_MEM_BLOCK_SYMBOLS; + // override the default value if the user sets it + if (rmt_config->mem_block_symbols) { + mem_block_symbols = rmt_config->mem_block_symbols; + } + rmt_tx_channel_config_t rmt_chan_config = { + .clk_src = clk_src, + .gpio_num = led_config->strip_gpio_num, + .mem_block_symbols = mem_block_symbols, + .resolution_hz = resolution, + .trans_queue_depth = LED_STRIP_RMT_DEFAULT_TRANS_QUEUE_SIZE, + .flags.with_dma = rmt_config->flags.with_dma, + .flags.invert_out = led_config->flags.invert_out, + }; + ESP_GOTO_ON_ERROR(rmt_new_tx_channel(&rmt_chan_config, &rmt_strip->rmt_chan), err, TAG, "create RMT TX channel failed"); + + led_strip_encoder_config_t strip_encoder_conf = { + .resolution = resolution, + .led_model = led_config->led_model + }; + ESP_GOTO_ON_ERROR(rmt_new_led_strip_encoder(&strip_encoder_conf, &rmt_strip->strip_encoder), err, TAG, "create LED strip encoder failed"); + + + rmt_strip->bytes_per_pixel = bytes_per_pixel; + rmt_strip->strip_len = led_config->max_leds; + rmt_strip->base.set_pixel = led_strip_rmt_set_pixel; + rmt_strip->base.set_pixel_rgbw = led_strip_rmt_set_pixel_rgbw; + rmt_strip->base.refresh = led_strip_rmt_refresh; + rmt_strip->base.clear = led_strip_rmt_clear; + rmt_strip->base.del = led_strip_rmt_del; + + *ret_strip = &rmt_strip->base; + return ESP_OK; +err: + if (rmt_strip) { + if (rmt_strip->rmt_chan) { + rmt_del_channel(rmt_strip->rmt_chan); + } + if (rmt_strip->strip_encoder) { + rmt_del_encoder(rmt_strip->strip_encoder); + } + free(rmt_strip); + } + return ret; +} diff --git a/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_dev_idf4.c b/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_dev_idf4.c new file mode 100644 index 000000000..a1067cd7c --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_dev_idf4.c @@ -0,0 +1,194 @@ +/* + * SPDX-FileCopyrightText: 2022-2023 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ +#include +#include +#include +#include "esp_log.h" +#include "esp_check.h" +#include "driver/rmt.h" +#include "led_strip.h" +#include "led_strip_interface.h" + +static const char *TAG = "led_strip_rmt"; + +#define WS2812_T0H_NS (300) +#define WS2812_T0L_NS (900) +#define WS2812_T1H_NS (900) +#define WS2812_T1L_NS (300) + +#define SK6812_T0H_NS (300) +#define SK6812_T0L_NS (900) +#define SK6812_T1H_NS (600) +#define SK6812_T1L_NS (600) + +#define LED_STRIP_RESET_MS (10) + +// the memory size of each RMT channel, in words (4 bytes) +#if CONFIG_IDF_TARGET_ESP32 || CONFIG_IDF_TARGET_ESP32S2 +#define LED_STRIP_RMT_DEFAULT_MEM_BLOCK_SYMBOLS 64 +#else +#define LED_STRIP_RMT_DEFAULT_MEM_BLOCK_SYMBOLS 48 +#endif + +static uint32_t led_t0h_ticks = 0; +static uint32_t led_t1h_ticks = 0; +static uint32_t led_t0l_ticks = 0; +static uint32_t led_t1l_ticks = 0; + +typedef struct { + led_strip_t base; + rmt_channel_t rmt_channel; + uint32_t strip_len; + uint8_t bytes_per_pixel; + uint8_t buffer[0]; +} led_strip_rmt_obj; + +static void IRAM_ATTR ws2812_rmt_adapter(const void *src, rmt_item32_t *dest, size_t src_size, + size_t wanted_num, size_t *translated_size, size_t *item_num) +{ + if (src == NULL || dest == NULL) { + *translated_size = 0; + *item_num = 0; + return; + } + const rmt_item32_t bit0 = {{{ led_t0h_ticks, 1, led_t0l_ticks, 0 }}}; //Logical 0 + const rmt_item32_t bit1 = {{{ led_t1h_ticks, 1, led_t1l_ticks, 0 }}}; //Logical 1 + size_t size = 0; + size_t num = 0; + uint8_t *psrc = (uint8_t *)src; + rmt_item32_t *pdest = dest; + while (size < src_size && num < wanted_num) { + for (int i = 0; i < 8; i++) { + // MSB first + if (*psrc & (1 << (7 - i))) { + pdest->val = bit1.val; + } else { + pdest->val = bit0.val; + } + num++; + pdest++; + } + size++; + psrc++; + } + *translated_size = size; + *item_num = num; +} + +static esp_err_t led_strip_rmt_set_pixel(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue) +{ + led_strip_rmt_obj *rmt_strip = __containerof(strip, led_strip_rmt_obj, base); + ESP_RETURN_ON_FALSE(index < rmt_strip->strip_len, ESP_ERR_INVALID_ARG, TAG, "index out of the maximum number of leds"); + uint32_t start = index * rmt_strip->bytes_per_pixel; + // In thr order of GRB + rmt_strip->buffer[start + 0] = green & 0xFF; + rmt_strip->buffer[start + 1] = red & 0xFF; + rmt_strip->buffer[start + 2] = blue & 0xFF; + if (rmt_strip->bytes_per_pixel > 3) { + rmt_strip->buffer[start + 3] = 0; + } + return ESP_OK; +} + +static esp_err_t led_strip_rmt_refresh(led_strip_t *strip) +{ + led_strip_rmt_obj *rmt_strip = __containerof(strip, led_strip_rmt_obj, base); + ESP_RETURN_ON_ERROR(rmt_write_sample(rmt_strip->rmt_channel, rmt_strip->buffer, rmt_strip->strip_len * rmt_strip->bytes_per_pixel, true), TAG, + "transmit RMT samples failed"); + vTaskDelay(pdMS_TO_TICKS(LED_STRIP_RESET_MS)); + return ESP_OK; +} + +static esp_err_t led_strip_rmt_clear(led_strip_t *strip) +{ + led_strip_rmt_obj *rmt_strip = __containerof(strip, led_strip_rmt_obj, base); + // Write zero to turn off all LEDs + memset(rmt_strip->buffer, 0, rmt_strip->strip_len * rmt_strip->bytes_per_pixel); + return led_strip_rmt_refresh(strip); +} + +static esp_err_t led_strip_rmt_del(led_strip_t *strip) +{ + led_strip_rmt_obj *rmt_strip = __containerof(strip, led_strip_rmt_obj, base); + ESP_RETURN_ON_ERROR(rmt_driver_uninstall(rmt_strip->rmt_channel), TAG, "uninstall RMT driver failed"); + free(rmt_strip); + return ESP_OK; +} + +esp_err_t led_strip_new_rmt_device(const led_strip_config_t *led_config, const led_strip_rmt_config_t *dev_config, led_strip_handle_t *ret_strip) +{ + led_strip_rmt_obj *rmt_strip = NULL; + esp_err_t ret = ESP_OK; + ESP_RETURN_ON_FALSE(led_config && dev_config && ret_strip, ESP_ERR_INVALID_ARG, TAG, "invalid argument"); + ESP_RETURN_ON_FALSE(led_config->led_pixel_format < LED_PIXEL_FORMAT_INVALID, ESP_ERR_INVALID_ARG, TAG, "invalid led_pixel_format"); + ESP_RETURN_ON_FALSE(dev_config->flags.with_dma == 0, ESP_ERR_NOT_SUPPORTED, TAG, "DMA is not supported"); + + uint8_t bytes_per_pixel = 3; + if (led_config->led_pixel_format == LED_PIXEL_FORMAT_GRBW) { + bytes_per_pixel = 4; + } else if (led_config->led_pixel_format == LED_PIXEL_FORMAT_GRB) { + bytes_per_pixel = 3; + } else { + assert(false); + } + + // allocate memory for led_strip object + rmt_strip = calloc(1, sizeof(led_strip_rmt_obj) + led_config->max_leds * bytes_per_pixel); + ESP_RETURN_ON_FALSE(rmt_strip, ESP_ERR_NO_MEM, TAG, "request memory for les_strip failed"); + + // install RMT channel driver + rmt_config_t config = RMT_DEFAULT_CONFIG_TX(led_config->strip_gpio_num, dev_config->rmt_channel); + // set the minimal clock division because the LED strip needs a high clock resolution + config.clk_div = 2; + + uint8_t mem_block_num = 2; + // override the default value if the user specify the mem block size + if (dev_config->mem_block_symbols) { + mem_block_num = (dev_config->mem_block_symbols + LED_STRIP_RMT_DEFAULT_MEM_BLOCK_SYMBOLS / 2) / LED_STRIP_RMT_DEFAULT_MEM_BLOCK_SYMBOLS; + } + config.mem_block_num = mem_block_num; + + ESP_GOTO_ON_ERROR(rmt_config(&config), err, TAG, "RMT config failed"); + ESP_GOTO_ON_ERROR(rmt_driver_install(config.channel, 0, 0), err, TAG, "RMT install failed"); + + uint32_t counter_clk_hz = 0; + rmt_get_counter_clock((rmt_channel_t)dev_config->rmt_channel, &counter_clk_hz); + // ns -> ticks + float ratio = (float)counter_clk_hz / 1e9; + if (led_config->led_model == LED_MODEL_WS2812) { + led_t0h_ticks = (uint32_t)(ratio * WS2812_T0H_NS); + led_t0l_ticks = (uint32_t)(ratio * WS2812_T0L_NS); + led_t1h_ticks = (uint32_t)(ratio * WS2812_T1H_NS); + led_t1l_ticks = (uint32_t)(ratio * WS2812_T1L_NS); + } else if (led_config->led_model == LED_MODEL_SK6812) { + led_t0h_ticks = (uint32_t)(ratio * SK6812_T0H_NS); + led_t0l_ticks = (uint32_t)(ratio * SK6812_T0L_NS); + led_t1h_ticks = (uint32_t)(ratio * SK6812_T1H_NS); + led_t1l_ticks = (uint32_t)(ratio * SK6812_T1L_NS); + } else { + assert(false); + } + + // adapter to translates the LES strip date frame into RMT symbols + rmt_translator_init((rmt_channel_t)dev_config->rmt_channel, ws2812_rmt_adapter); + + rmt_strip->bytes_per_pixel = bytes_per_pixel; + rmt_strip->rmt_channel = (rmt_channel_t)dev_config->rmt_channel; + rmt_strip->strip_len = led_config->max_leds; + rmt_strip->base.set_pixel = led_strip_rmt_set_pixel; + rmt_strip->base.refresh = led_strip_rmt_refresh; + rmt_strip->base.clear = led_strip_rmt_clear; + rmt_strip->base.del = led_strip_rmt_del; + + *ret_strip = &rmt_strip->base; + return ESP_OK; + +err: + if (rmt_strip) { + free(rmt_strip); + } + return ret; +} diff --git a/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_encoder.c b/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_encoder.c new file mode 100644 index 000000000..d352ac07f --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_encoder.c @@ -0,0 +1,146 @@ +/* + * SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ + +#include "esp_check.h" +#include "led_strip_rmt_encoder.h" + +static const char *TAG = "led_rmt_encoder"; + +typedef struct { + rmt_encoder_t base; + rmt_encoder_t *bytes_encoder; + rmt_encoder_t *copy_encoder; + int state; + rmt_symbol_word_t reset_code; +} rmt_led_strip_encoder_t; + +static size_t rmt_encode_led_strip(rmt_encoder_t *encoder, rmt_channel_handle_t channel, const void *primary_data, size_t data_size, rmt_encode_state_t *ret_state) +{ + rmt_led_strip_encoder_t *led_encoder = __containerof(encoder, rmt_led_strip_encoder_t, base); + rmt_encoder_handle_t bytes_encoder = led_encoder->bytes_encoder; + rmt_encoder_handle_t copy_encoder = led_encoder->copy_encoder; + rmt_encode_state_t session_state = 0; + rmt_encode_state_t state = 0; + size_t encoded_symbols = 0; + switch (led_encoder->state) { + case 0: // send RGB data + encoded_symbols += bytes_encoder->encode(bytes_encoder, channel, primary_data, data_size, &session_state); + if (session_state & RMT_ENCODING_COMPLETE) { + led_encoder->state = 1; // switch to next state when current encoding session finished + } + if (session_state & RMT_ENCODING_MEM_FULL) { + state |= RMT_ENCODING_MEM_FULL; + goto out; // yield if there's no free space for encoding artifacts + } + // fall-through + case 1: // send reset code + encoded_symbols += copy_encoder->encode(copy_encoder, channel, &led_encoder->reset_code, + sizeof(led_encoder->reset_code), &session_state); + if (session_state & RMT_ENCODING_COMPLETE) { + led_encoder->state = 0; // back to the initial encoding session + state |= RMT_ENCODING_COMPLETE; + } + if (session_state & RMT_ENCODING_MEM_FULL) { + state |= RMT_ENCODING_MEM_FULL; + goto out; // yield if there's no free space for encoding artifacts + } + } +out: + *ret_state = state; + return encoded_symbols; +} + +static esp_err_t rmt_del_led_strip_encoder(rmt_encoder_t *encoder) +{ + rmt_led_strip_encoder_t *led_encoder = __containerof(encoder, rmt_led_strip_encoder_t, base); + rmt_del_encoder(led_encoder->bytes_encoder); + rmt_del_encoder(led_encoder->copy_encoder); + free(led_encoder); + return ESP_OK; +} + +static esp_err_t rmt_led_strip_encoder_reset(rmt_encoder_t *encoder) +{ + rmt_led_strip_encoder_t *led_encoder = __containerof(encoder, rmt_led_strip_encoder_t, base); + rmt_encoder_reset(led_encoder->bytes_encoder); + rmt_encoder_reset(led_encoder->copy_encoder); + led_encoder->state = 0; + return ESP_OK; +} + +esp_err_t rmt_new_led_strip_encoder(const led_strip_encoder_config_t *config, rmt_encoder_handle_t *ret_encoder) +{ + esp_err_t ret = ESP_OK; + rmt_led_strip_encoder_t *led_encoder = NULL; + ESP_GOTO_ON_FALSE(config && ret_encoder, ESP_ERR_INVALID_ARG, err, TAG, "invalid argument"); + ESP_GOTO_ON_FALSE(config->led_model < LED_MODEL_INVALID, ESP_ERR_INVALID_ARG, err, TAG, "invalid led model"); + led_encoder = calloc(1, sizeof(rmt_led_strip_encoder_t)); + ESP_GOTO_ON_FALSE(led_encoder, ESP_ERR_NO_MEM, err, TAG, "no mem for led strip encoder"); + led_encoder->base.encode = rmt_encode_led_strip; + led_encoder->base.del = rmt_del_led_strip_encoder; + led_encoder->base.reset = rmt_led_strip_encoder_reset; + rmt_bytes_encoder_config_t bytes_encoder_config; + if (config->led_model == LED_MODEL_SK6812) { + bytes_encoder_config = (rmt_bytes_encoder_config_t) { + .bit0 = { + .level0 = 1, + .duration0 = 0.3 * config->resolution / 1000000, // T0H=0.3us + .level1 = 0, + .duration1 = 0.9 * config->resolution / 1000000, // T0L=0.9us + }, + .bit1 = { + .level0 = 1, + .duration0 = 0.6 * config->resolution / 1000000, // T1H=0.6us + .level1 = 0, + .duration1 = 0.6 * config->resolution / 1000000, // T1L=0.6us + }, + .flags.msb_first = 1 // SK6812 transfer bit order: G7...G0R7...R0B7...B0(W7...W0) + }; + } else if (config->led_model == LED_MODEL_WS2812) { + // different led strip might have its own timing requirements, following parameter is for WS2812 + bytes_encoder_config = (rmt_bytes_encoder_config_t) { + .bit0 = { + .level0 = 1, + .duration0 = 0.3 * config->resolution / 1000000, // T0H=0.3us + .level1 = 0, + .duration1 = 0.9 * config->resolution / 1000000, // T0L=0.9us + }, + .bit1 = { + .level0 = 1, + .duration0 = 0.9 * config->resolution / 1000000, // T1H=0.9us + .level1 = 0, + .duration1 = 0.3 * config->resolution / 1000000, // T1L=0.3us + }, + .flags.msb_first = 1 // WS2812 transfer bit order: G7...G0R7...R0B7...B0 + }; + } else { + assert(false); + } + ESP_GOTO_ON_ERROR(rmt_new_bytes_encoder(&bytes_encoder_config, &led_encoder->bytes_encoder), err, TAG, "create bytes encoder failed"); + rmt_copy_encoder_config_t copy_encoder_config = {}; + ESP_GOTO_ON_ERROR(rmt_new_copy_encoder(©_encoder_config, &led_encoder->copy_encoder), err, TAG, "create copy encoder failed"); + + uint32_t reset_ticks = config->resolution / 1000000 * 50 / 2; // reset code duration defaults to 50us + led_encoder->reset_code = (rmt_symbol_word_t) { + .level0 = 0, + .duration0 = reset_ticks, + .level1 = 0, + .duration1 = reset_ticks, + }; + *ret_encoder = &led_encoder->base; + return ESP_OK; +err: + if (led_encoder) { + if (led_encoder->bytes_encoder) { + rmt_del_encoder(led_encoder->bytes_encoder); + } + if (led_encoder->copy_encoder) { + rmt_del_encoder(led_encoder->copy_encoder); + } + free(led_encoder); + } + return ret; +} diff --git a/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_encoder.h b/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_encoder.h new file mode 100644 index 000000000..ba71e60ab --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_encoder.h @@ -0,0 +1,38 @@ +/* + * SPDX-FileCopyrightText: 2022 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ +#pragma once + +#include +#include "driver/rmt_encoder.h" +#include "led_strip_types.h" + +#ifdef __cplusplus +extern "C" { +#endif + +/** + * @brief Type of led strip encoder configuration + */ +typedef struct { + uint32_t resolution; /*!< Encoder resolution, in Hz */ + led_model_t led_model; /*!< LED model */ +} led_strip_encoder_config_t; + +/** + * @brief Create RMT encoder for encoding LED strip pixels into RMT symbols + * + * @param[in] config Encoder configuration + * @param[out] ret_encoder Returned encoder handle + * @return + * - ESP_ERR_INVALID_ARG for any invalid arguments + * - ESP_ERR_NO_MEM out of memory when creating led strip encoder + * - ESP_OK if creating encoder successfully + */ +esp_err_t rmt_new_led_strip_encoder(const led_strip_encoder_config_t *config, rmt_encoder_handle_t *ret_encoder); + +#ifdef __cplusplus +} +#endif diff --git a/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_ws2812.c b/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_ws2812.c deleted file mode 100644 index fd1746cad..000000000 --- a/hw/bsp/espressif/components/led_strip/src/led_strip_rmt_ws2812.c +++ /dev/null @@ -1,171 +0,0 @@ -// Copyright 2019 Espressif Systems (Shanghai) PTE LTD -// -// Licensed under the Apache License, Version 2.0 (the "License"); -// you may not use this file except in compliance with the License. -// You may obtain a copy of the License at -// -// http://www.apache.org/licenses/LICENSE-2.0 -// -// Unless required by applicable law or agreed to in writing, software -// distributed under the License is distributed on an "AS IS" BASIS, -// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. -// See the License for the specific language governing permissions and -// limitations under the License. -#include -#include -#include -#include "esp_log.h" -#include "esp_attr.h" -#include "led_strip.h" -#include "driver/rmt.h" - -static const char *TAG = "ws2812"; -#define STRIP_CHECK(a, str, goto_tag, ret_value, ...) \ - do \ - { \ - if (!(a)) \ - { \ - ESP_LOGE(TAG, "%s(%d): " str, __FUNCTION__, __LINE__, ##__VA_ARGS__); \ - ret = ret_value; \ - goto goto_tag; \ - } \ - } while (0) - -#define WS2812_T0H_NS (350) -#define WS2812_T0L_NS (1000) -#define WS2812_T1H_NS (1000) -#define WS2812_T1L_NS (350) -#define WS2812_RESET_US (280) - -static uint32_t ws2812_t0h_ticks = 0; -static uint32_t ws2812_t1h_ticks = 0; -static uint32_t ws2812_t0l_ticks = 0; -static uint32_t ws2812_t1l_ticks = 0; - -typedef struct { - led_strip_t parent; - rmt_channel_t rmt_channel; - uint32_t strip_len; - uint8_t buffer[0]; -} ws2812_t; - -/** - * @brief Convert RGB data to RMT format. - * - * @note For WS2812, R,G,B each contains 256 different choices (i.e. uint8_t) - * - * @param[in] src: source data, to converted to RMT format - * @param[in] dest: place where to store the convert result - * @param[in] src_size: size of source data - * @param[in] wanted_num: number of RMT items that want to get - * @param[out] translated_size: number of source data that got converted - * @param[out] item_num: number of RMT items which are converted from source data - */ -static void IRAM_ATTR ws2812_rmt_adapter(const void *src, rmt_item32_t *dest, size_t src_size, - size_t wanted_num, size_t *translated_size, size_t *item_num) -{ - if (src == NULL || dest == NULL) { - *translated_size = 0; - *item_num = 0; - return; - } - const rmt_item32_t bit0 = {{{ ws2812_t0h_ticks, 1, ws2812_t0l_ticks, 0 }}}; //Logical 0 - const rmt_item32_t bit1 = {{{ ws2812_t1h_ticks, 1, ws2812_t1l_ticks, 0 }}}; //Logical 1 - size_t size = 0; - size_t num = 0; - uint8_t *psrc = (uint8_t *)src; - rmt_item32_t *pdest = dest; - while (size < src_size && num < wanted_num) { - for (int i = 0; i < 8; i++) { - // MSB first - if (*psrc & (1 << (7 - i))) { - pdest->val = bit1.val; - } else { - pdest->val = bit0.val; - } - num++; - pdest++; - } - size++; - psrc++; - } - *translated_size = size; - *item_num = num; -} - -static esp_err_t ws2812_set_pixel(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue) -{ - esp_err_t ret = ESP_OK; - ws2812_t *ws2812 = __containerof(strip, ws2812_t, parent); - STRIP_CHECK(index < ws2812->strip_len, "index out of the maximum number of leds", err, ESP_ERR_INVALID_ARG); - uint32_t start = index * 3; - // In thr order of GRB - ws2812->buffer[start + 0] = green & 0xFF; - ws2812->buffer[start + 1] = red & 0xFF; - ws2812->buffer[start + 2] = blue & 0xFF; - return ESP_OK; -err: - return ret; -} - -static esp_err_t ws2812_refresh(led_strip_t *strip, uint32_t timeout_ms) -{ - esp_err_t ret = ESP_OK; - ws2812_t *ws2812 = __containerof(strip, ws2812_t, parent); - STRIP_CHECK(rmt_write_sample(ws2812->rmt_channel, ws2812->buffer, ws2812->strip_len * 3, true) == ESP_OK, - "transmit RMT samples failed", err, ESP_FAIL); - return rmt_wait_tx_done(ws2812->rmt_channel, pdMS_TO_TICKS(timeout_ms)); -err: - return ret; -} - -static esp_err_t ws2812_clear(led_strip_t *strip, uint32_t timeout_ms) -{ - ws2812_t *ws2812 = __containerof(strip, ws2812_t, parent); - // Write zero to turn off all leds - memset(ws2812->buffer, 0, ws2812->strip_len * 3); - return ws2812_refresh(strip, timeout_ms); -} - -static esp_err_t ws2812_del(led_strip_t *strip) -{ - ws2812_t *ws2812 = __containerof(strip, ws2812_t, parent); - free(ws2812); - return ESP_OK; -} - -led_strip_t *led_strip_new_rmt_ws2812(const led_strip_config_t *config) -{ - led_strip_t *ret = NULL; - STRIP_CHECK(config, "configuration can't be null", err, NULL); - - // 24 bits per led - uint32_t ws2812_size = sizeof(ws2812_t) + config->max_leds * 3; - ws2812_t *ws2812 = calloc(1, ws2812_size); - STRIP_CHECK(ws2812, "request memory for ws2812 failed", err, NULL); - - uint32_t counter_clk_hz = 0; - STRIP_CHECK(rmt_get_counter_clock((rmt_channel_t)config->dev, &counter_clk_hz) == ESP_OK, - "get rmt counter clock failed", err, NULL); - // ns -> ticks - float ratio = (float)counter_clk_hz / 1e9; - ws2812_t0h_ticks = (uint32_t)(ratio * WS2812_T0H_NS); - ws2812_t0l_ticks = (uint32_t)(ratio * WS2812_T0L_NS); - ws2812_t1h_ticks = (uint32_t)(ratio * WS2812_T1H_NS); - ws2812_t1l_ticks = (uint32_t)(ratio * WS2812_T1L_NS); - - // set ws2812 to rmt adapter - rmt_translator_init((rmt_channel_t)config->dev, ws2812_rmt_adapter); - - ws2812->rmt_channel = (rmt_channel_t)config->dev; - ws2812->strip_len = config->max_leds; - - ws2812->parent.set_pixel = ws2812_set_pixel; - ws2812->parent.refresh = ws2812_refresh; - ws2812->parent.clear = ws2812_clear; - ws2812->parent.del = ws2812_del; - - return &ws2812->parent; -err: - return ret; -} diff --git a/hw/bsp/espressif/components/led_strip/src/led_strip_spi_dev.c b/hw/bsp/espressif/components/led_strip/src/led_strip_spi_dev.c new file mode 100644 index 000000000..12ea8fbf3 --- /dev/null +++ b/hw/bsp/espressif/components/led_strip/src/led_strip_spi_dev.c @@ -0,0 +1,209 @@ +/* + * SPDX-FileCopyrightText: 2022-2023 Espressif Systems (Shanghai) CO LTD + * + * SPDX-License-Identifier: Apache-2.0 + */ +#include +#include +#include +#include "esp_log.h" +#include "esp_check.h" +#include "esp_rom_gpio.h" +#include "soc/spi_periph.h" +#include "led_strip.h" +#include "led_strip_interface.h" +#include "hal/spi_hal.h" + +#define LED_STRIP_SPI_DEFAULT_RESOLUTION (2.5 * 1000 * 1000) // 2.5MHz resolution +#define LED_STRIP_SPI_DEFAULT_TRANS_QUEUE_SIZE 4 + +#define SPI_BYTES_PER_COLOR_BYTE 3 +#define SPI_BITS_PER_COLOR_BYTE (SPI_BYTES_PER_COLOR_BYTE * 8) + +static const char *TAG = "led_strip_spi"; + +typedef struct { + led_strip_t base; + spi_host_device_t spi_host; + spi_device_handle_t spi_device; + uint32_t strip_len; + uint8_t bytes_per_pixel; + uint8_t pixel_buf[]; +} led_strip_spi_obj; + +// please make sure to zero-initialize the buf before calling this function +static void __led_strip_spi_bit(uint8_t data, uint8_t *buf) +{ + // Each color of 1 bit is represented by 3 bits of SPI, low_level:100 ,high_level:110 + // So a color byte occupies 3 bytes of SPI. + *(buf + 2) |= data & BIT(0) ? BIT(2) | BIT(1) : BIT(2); + *(buf + 2) |= data & BIT(1) ? BIT(5) | BIT(4) : BIT(5); + *(buf + 2) |= data & BIT(2) ? BIT(7) : 0x00; + *(buf + 1) |= BIT(0); + *(buf + 1) |= data & BIT(3) ? BIT(3) | BIT(2) : BIT(3); + *(buf + 1) |= data & BIT(4) ? BIT(6) | BIT(5) : BIT(6); + *(buf + 0) |= data & BIT(5) ? BIT(1) | BIT(0) : BIT(1); + *(buf + 0) |= data & BIT(6) ? BIT(4) | BIT(3) : BIT(4); + *(buf + 0) |= data & BIT(7) ? BIT(7) | BIT(6) : BIT(7); +} + +static esp_err_t led_strip_spi_set_pixel(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue) +{ + led_strip_spi_obj *spi_strip = __containerof(strip, led_strip_spi_obj, base); + ESP_RETURN_ON_FALSE(index < spi_strip->strip_len, ESP_ERR_INVALID_ARG, TAG, "index out of maximum number of LEDs"); + // LED_PIXEL_FORMAT_GRB takes 72bits(9bytes) + uint32_t start = index * spi_strip->bytes_per_pixel * SPI_BYTES_PER_COLOR_BYTE; + memset(spi_strip->pixel_buf + start, 0, spi_strip->bytes_per_pixel * SPI_BYTES_PER_COLOR_BYTE); + __led_strip_spi_bit(green, &spi_strip->pixel_buf[start]); + __led_strip_spi_bit(red, &spi_strip->pixel_buf[start + SPI_BYTES_PER_COLOR_BYTE]); + __led_strip_spi_bit(blue, &spi_strip->pixel_buf[start + SPI_BYTES_PER_COLOR_BYTE * 2]); + if (spi_strip->bytes_per_pixel > 3) { + __led_strip_spi_bit(0, &spi_strip->pixel_buf[start + SPI_BYTES_PER_COLOR_BYTE * 3]); + } + return ESP_OK; +} + +static esp_err_t led_strip_spi_set_pixel_rgbw(led_strip_t *strip, uint32_t index, uint32_t red, uint32_t green, uint32_t blue, uint32_t white) +{ + led_strip_spi_obj *spi_strip = __containerof(strip, led_strip_spi_obj, base); + ESP_RETURN_ON_FALSE(index < spi_strip->strip_len, ESP_ERR_INVALID_ARG, TAG, "index out of maximum number of LEDs"); + ESP_RETURN_ON_FALSE(spi_strip->bytes_per_pixel == 4, ESP_ERR_INVALID_ARG, TAG, "wrong LED pixel format, expected 4 bytes per pixel"); + // LED_PIXEL_FORMAT_GRBW takes 96bits(12bytes) + uint32_t start = index * spi_strip->bytes_per_pixel * SPI_BYTES_PER_COLOR_BYTE; + // SK6812 component order is GRBW + memset(spi_strip->pixel_buf + start, 0, spi_strip->bytes_per_pixel * SPI_BYTES_PER_COLOR_BYTE); + __led_strip_spi_bit(green, &spi_strip->pixel_buf[start]); + __led_strip_spi_bit(red, &spi_strip->pixel_buf[start + SPI_BYTES_PER_COLOR_BYTE]); + __led_strip_spi_bit(blue, &spi_strip->pixel_buf[start + SPI_BYTES_PER_COLOR_BYTE * 2]); + __led_strip_spi_bit(white, &spi_strip->pixel_buf[start + SPI_BYTES_PER_COLOR_BYTE * 3]); + + return ESP_OK; +} + +static esp_err_t led_strip_spi_refresh(led_strip_t *strip) +{ + led_strip_spi_obj *spi_strip = __containerof(strip, led_strip_spi_obj, base); + spi_transaction_t tx_conf; + memset(&tx_conf, 0, sizeof(tx_conf)); + + tx_conf.length = spi_strip->strip_len * spi_strip->bytes_per_pixel * SPI_BITS_PER_COLOR_BYTE; + tx_conf.tx_buffer = spi_strip->pixel_buf; + tx_conf.rx_buffer = NULL; + ESP_RETURN_ON_ERROR(spi_device_transmit(spi_strip->spi_device, &tx_conf), TAG, "transmit pixels by SPI failed"); + + return ESP_OK; +} + +static esp_err_t led_strip_spi_clear(led_strip_t *strip) +{ + led_strip_spi_obj *spi_strip = __containerof(strip, led_strip_spi_obj, base); + //Write zero to turn off all leds + memset(spi_strip->pixel_buf, 0, spi_strip->strip_len * spi_strip->bytes_per_pixel * SPI_BYTES_PER_COLOR_BYTE); + uint8_t *buf = spi_strip->pixel_buf; + for (int index = 0; index < spi_strip->strip_len * spi_strip->bytes_per_pixel; index++) { + __led_strip_spi_bit(0, buf); + buf += SPI_BYTES_PER_COLOR_BYTE; + } + + return led_strip_spi_refresh(strip); +} + +static esp_err_t led_strip_spi_del(led_strip_t *strip) +{ + led_strip_spi_obj *spi_strip = __containerof(strip, led_strip_spi_obj, base); + + ESP_RETURN_ON_ERROR(spi_bus_remove_device(spi_strip->spi_device), TAG, "delete spi device failed"); + ESP_RETURN_ON_ERROR(spi_bus_free(spi_strip->spi_host), TAG, "free spi bus failed"); + + free(spi_strip); + return ESP_OK; +} + +esp_err_t led_strip_new_spi_device(const led_strip_config_t *led_config, const led_strip_spi_config_t *spi_config, led_strip_handle_t *ret_strip) +{ + led_strip_spi_obj *spi_strip = NULL; + esp_err_t ret = ESP_OK; + ESP_GOTO_ON_FALSE(led_config && spi_config && ret_strip, ESP_ERR_INVALID_ARG, err, TAG, "invalid argument"); + ESP_GOTO_ON_FALSE(led_config->led_pixel_format < LED_PIXEL_FORMAT_INVALID, ESP_ERR_INVALID_ARG, err, TAG, "invalid led_pixel_format"); + uint8_t bytes_per_pixel = 3; + if (led_config->led_pixel_format == LED_PIXEL_FORMAT_GRBW) { + bytes_per_pixel = 4; + } else if (led_config->led_pixel_format == LED_PIXEL_FORMAT_GRB) { + bytes_per_pixel = 3; + } else { + assert(false); + } + uint32_t mem_caps = MALLOC_CAP_DEFAULT; + if (spi_config->flags.with_dma) { + // DMA buffer must be placed in internal SRAM + mem_caps |= MALLOC_CAP_INTERNAL | MALLOC_CAP_DMA; + } + spi_strip = heap_caps_calloc(1, sizeof(led_strip_spi_obj) + led_config->max_leds * bytes_per_pixel * SPI_BYTES_PER_COLOR_BYTE, mem_caps); + + ESP_GOTO_ON_FALSE(spi_strip, ESP_ERR_NO_MEM, err, TAG, "no mem for spi strip"); + + spi_strip->spi_host = spi_config->spi_bus; + // for backward compatibility, if the user does not set the clk_src, use the default value + spi_clock_source_t clk_src = SPI_CLK_SRC_DEFAULT; + if (spi_config->clk_src) { + clk_src = spi_config->clk_src; + } + + spi_bus_config_t spi_bus_cfg = { + .mosi_io_num = led_config->strip_gpio_num, + //Only use MOSI to generate the signal, set -1 when other pins are not used. + .miso_io_num = -1, + .sclk_io_num = -1, + .quadwp_io_num = -1, + .quadhd_io_num = -1, + .max_transfer_sz = led_config->max_leds * bytes_per_pixel * SPI_BYTES_PER_COLOR_BYTE, + }; + ESP_GOTO_ON_ERROR(spi_bus_initialize(spi_strip->spi_host, &spi_bus_cfg, spi_config->flags.with_dma ? SPI_DMA_CH_AUTO : SPI_DMA_DISABLED), err, TAG, "create SPI bus failed"); + + if (led_config->flags.invert_out == true) { + esp_rom_gpio_connect_out_signal(led_config->strip_gpio_num, spi_periph_signal[spi_strip->spi_host].spid_out, true, false); + } + + spi_device_interface_config_t spi_dev_cfg = { + .clock_source = clk_src, + .command_bits = 0, + .address_bits = 0, + .dummy_bits = 0, + .clock_speed_hz = LED_STRIP_SPI_DEFAULT_RESOLUTION, + .mode = 0, + //set -1 when CS is not used + .spics_io_num = -1, + .queue_size = LED_STRIP_SPI_DEFAULT_TRANS_QUEUE_SIZE, + }; + + ESP_GOTO_ON_ERROR(spi_bus_add_device(spi_strip->spi_host, &spi_dev_cfg, &spi_strip->spi_device), err, TAG, "Failed to add spi device"); + + int clock_resolution_khz = 0; + spi_device_get_actual_freq(spi_strip->spi_device, &clock_resolution_khz); + // TODO: ideally we should decide the SPI_BYTES_PER_COLOR_BYTE by the real clock resolution + // But now, let's fixed the resolution, the downside is, we don't support a clock source whose frequency is not multiple of LED_STRIP_SPI_DEFAULT_RESOLUTION + ESP_GOTO_ON_FALSE(clock_resolution_khz == LED_STRIP_SPI_DEFAULT_RESOLUTION / 1000, ESP_ERR_NOT_SUPPORTED, err, + TAG, "unsupported clock resolution:%dKHz", clock_resolution_khz); + + spi_strip->bytes_per_pixel = bytes_per_pixel; + spi_strip->strip_len = led_config->max_leds; + spi_strip->base.set_pixel = led_strip_spi_set_pixel; + spi_strip->base.set_pixel_rgbw = led_strip_spi_set_pixel_rgbw; + spi_strip->base.refresh = led_strip_spi_refresh; + spi_strip->base.clear = led_strip_spi_clear; + spi_strip->base.del = led_strip_spi_del; + + *ret_strip = &spi_strip->base; + return ESP_OK; +err: + if (spi_strip) { + if (spi_strip->spi_device) { + spi_bus_remove_device(spi_strip->spi_device); + } + if (spi_strip->spi_host) { + spi_bus_free(spi_strip->spi_host); + } + free(spi_strip); + } + return ret; +} diff --git a/hw/bsp/family_support.cmake b/hw/bsp/family_support.cmake index 539a776a6..ff3393cfd 100644 --- a/hw/bsp/family_support.cmake +++ b/hw/bsp/family_support.cmake @@ -211,7 +211,6 @@ function(family_configure_common TARGET RTOS) target_link_options(${TARGET} PUBLIC "LINKER:--map=$.map") endif() - # ETM Trace option if (TRACE_ETM STREQUAL "1") target_compile_definitions(${TARGET} PUBLIC TRACE_ETM) diff --git a/hw/bsp/mcx/boards/bunny-brain/board.cmake b/hw/bsp/mcx/boards/bunny-brain/board.cmake deleted file mode 100644 index 8c3280743..000000000 --- a/hw/bsp/mcx/boards/bunny-brain/board.cmake +++ /dev/null @@ -1,21 +0,0 @@ -set(MCU_VARIANT MCXN947) -set(MCU_CORE MCXN947_cm33_core0) - -set(JLINK_DEVICE MCXN947_M33_0) -set(PYOCD_TARGET MCXN947) -set(NXPLINK_DEVICE MCXN947:MCXN947) - -set(PORT 1) - -function(update_board TARGET) - target_compile_definitions(${TARGET} PUBLIC - CPU_MCXN947VDF_cm33_core0 - BOARD_TUD_RHPORT=${PORT} - # port 0 is fullspeed, port 1 is highspeed - BOARD_TUD_MAX_SPEED=$ - ) - target_sources(${TARGET} PUBLIC - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/clock_config.c - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/pin_mux.c - ) -endfunction() diff --git a/hw/bsp/mcx/boards/bunny-brain/board.h b/hw/bsp/mcx/boards/bunny-brain/board.h deleted file mode 100644 index eae98bfa7..000000000 --- a/hw/bsp/mcx/boards/bunny-brain/board.h +++ /dev/null @@ -1,66 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#ifndef BOARD_H_ -#define BOARD_H_ - -#ifdef __cplusplus - extern "C" { -#endif - -// LED -#define LED_GPIO GPIO3 -#define LED_CLK kCLOCK_Gpio3 -#define LED_PIN 4 // red -#define LED_STATE_ON 0 - -// WAKE button (Dummy, use unused pin -#define BUTTON_GPIO GPIO0 -#define BUTTON_CLK kCLOCK_Gpio0 -#define BUTTON_PIN 6 -#define BUTTON_STATE_ACTIVE 0 - -// UART -#define UART_DEV LPUART4 - -static inline void board_uart_init_clock(void) { - /* attach FRO 12M to FLEXCOMM4 */ - CLOCK_SetClkDiv(kCLOCK_DivFlexcom4Clk, 1u); - CLOCK_AttachClk(kFRO12M_to_FLEXCOMM4); - RESET_ClearPeripheralReset(kFC4_RST_SHIFT_RSTn); -} - -//#define UART_RX_PINMUX 0, 24, IOCON_PIO_DIG_FUNC1_EN -//#define UART_TX_PINMUX 0, 25, IOCON_PIO_DIG_FUNC1_EN - -// XTAL -#define XTAL0_CLK_HZ (24 * 1000 * 1000U) - -#ifdef __cplusplus - } -#endif - -#endif diff --git a/hw/bsp/mcx/boards/bunny-brain/board.mk b/hw/bsp/mcx/boards/bunny-brain/board.mk deleted file mode 100644 index aaad5e73e..000000000 --- a/hw/bsp/mcx/boards/bunny-brain/board.mk +++ /dev/null @@ -1,11 +0,0 @@ -MCU_VARIANT = MCXN947 -MCU_CORE = MCXN947_cm33_core0 -PORT ?= 1 - -CFLAGS += -DCPU_MCXN947VDF_cm33_core0 - -JLINK_DEVICE = MCXN947_M33_0 -PYOCD_TARGET = MCXN947 - -# flash using pyocd -flash: flash-jlink diff --git a/hw/bsp/mcx/boards/bunny-brain/clock_config.c b/hw/bsp/mcx/boards/bunny-brain/clock_config.c deleted file mode 100644 index 37d2b4dfc..000000000 --- a/hw/bsp/mcx/boards/bunny-brain/clock_config.c +++ /dev/null @@ -1,338 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ -/* - * How to setup clock using clock driver functions: - * - * 1. Setup clock sources. - * - * 2. Set up wait states of the flash. - * - * 3. Set up all dividers. - * - * 4. Set up all selectors to provide selected clocks. - * - */ - -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Clocks v10.0 -processor: MCXN947 -package_id: MCXN947VDF -mcu_data: ksdk2_0 -processor_version: 0.12.3 -board: MCX-N9XX-EVK - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -#include "clock_config.h" -#include "fsl_clock.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ - -/******************************************************************************* - * Variables - ******************************************************************************/ -/* System clock frequency. */ -// extern uint32_t SystemCoreClock; - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ -void BOARD_InitBootClocks(void) -{ - BOARD_BootClockPLL150M(); -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO12M ********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFRO12M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: MAIN_clock.outFreq, value: 12 MHz} -- {id: Slow_clock.outFreq, value: 3 MHz} -- {id: System_clock.outFreq, value: 12 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SCGMode, value: SIRC} -- {id: SCG.SCSSEL.sel, value: SCG.SIRC} -- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -void BOARD_BootClockFRO12M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO12M */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK; -} - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF48M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFROHF48M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 48 MHz} -- {id: Slow_clock.outFreq, value: 12 MHz} -- {id: System_clock.outFreq, value: 48 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -void BOARD_BootClockFROHF48M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK; -} - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF144M ******************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFROHF144M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 144 MHz} -- {id: MAIN_clock.outFreq, value: 144 MHz} -- {id: Slow_clock.outFreq, value: 18 MHz} -- {id: System_clock.outFreq, value: 72 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true} -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} -sources: -- {id: SCG.FIRC.outFreq, value: 144 MHz} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -void BOARD_BootClockFROHF144M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(144000000U); /*!< Enable FRO HF(144MHz) output */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 2U); /*!< Set AHBCLKDIV divider to value 2 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK; -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL150M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockPLL150M -called_from_default_init: true -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 150 MHz} -- {id: PLL0_CLK_clock.outFreq, value: 150 MHz} -- {id: Slow_clock.outFreq, value: 37.5 MHz} -- {id: System_clock.outFreq, value: 150 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: PLL0_Mode, value: Normal} -- {id: RunPowerMode, value: OD} -- {id: SCGMode, value: PLL0} -- {id: SCG.PLL0M_MULT.scale, value: '50', locked: true} -- {id: SCG.PLL0SRCSEL.sel, value: SCG.FIRC_48M} -- {id: SCG.PLL0_NDIV.scale, value: '8', locked: true} -- {id: SCG.SCSSEL.sel, value: SCG.PLL0_CLK} -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -void BOARD_BootClockPLL150M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - /*!< Set up PLL0 */ - const pll_setup_t pll0Setup = { - .pllctrl = SCG_APLLCTRL_SOURCE(1U) | SCG_APLLCTRL_SELI(27U) | SCG_APLLCTRL_SELP(13U), - .pllndiv = SCG_APLLNDIV_NDIV(8U), - .pllpdiv = SCG_APLLPDIV_PDIV(1U), - .pllmdiv = SCG_APLLMDIV_MDIV(50U), - .pllRate = 150000000U - }; - CLOCK_SetPLL0Freq(&pll0Setup); /*!< Configure PLL0 to the desired values */ - CLOCK_SetPll0MonitorMode(kSCG_Pll0MonitorDisable); /* Pll0 Monitor is disabled */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kPLL0_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL0 */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKPLL150M_CORE_CLOCK; -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL100M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockPLL100M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: CLK_IN_clock.outFreq, value: 24 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: MAIN_clock.outFreq, value: 100 MHz} -- {id: PLL1_CLK_clock.outFreq, value: 100 MHz} -- {id: Slow_clock.outFreq, value: 25 MHz} -- {id: System_clock.outFreq, value: 100 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: PLL1_Mode, value: Normal} -- {id: SCGMode, value: PLL1} -- {id: SCG.PLL1M_MULT.scale, value: '100', locked: true} -- {id: SCG.PLL1_NDIV.scale, value: '6', locked: true} -- {id: SCG.PLL1_PDIV.scale, value: '4', locked: true} -- {id: SCG.SCSSEL.sel, value: SCG.PLL1_CLK} -- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} -- {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} -sources: -- {id: SCG.SOSC.outFreq, value: 24 MHz, enabled: true} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -void BOARD_BootClockPLL100M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupExtClocking(24000000U); - CLOCK_SetSysOscMonitorMode(kSCG_SysOscMonitorDisable); /* System OSC Clock Monitor is disabled */ - - /*!< Set up PLL1 */ - const pll_setup_t pll1Setup = { - .pllctrl = SCG_SPLLCTRL_SOURCE(0U) | SCG_SPLLCTRL_SELI(53U) | SCG_SPLLCTRL_SELP(26U), - .pllndiv = SCG_SPLLNDIV_NDIV(6U), - .pllpdiv = SCG_SPLLPDIV_PDIV(2U), - .pllmdiv = SCG_SPLLMDIV_MDIV(100U), - .pllRate = 100000000U - }; - CLOCK_SetPLL1Freq(&pll1Setup); /*!< Configure PLL1 to the desired values */ - CLOCK_SetPll1MonitorMode(kSCG_Pll1MonitorDisable); /* Pll1 Monitor is disabled */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kPLL1_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL1 */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKPLL100M_CORE_CLOCK; -} diff --git a/hw/bsp/mcx/boards/bunny-brain/clock_config.h b/hw/bsp/mcx/boards/bunny-brain/clock_config.h deleted file mode 100644 index c238a0423..000000000 --- a/hw/bsp/mcx/boards/bunny-brain/clock_config.h +++ /dev/null @@ -1,177 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _CLOCK_CONFIG_H_ -#define _CLOCK_CONFIG_H_ - -#include "fsl_common.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ -#define BOARD_XTAL0_CLK_HZ 24000000U /*!< Board xtal frequency in Hz */ -#define BOARD_XTAL32K_CLK_HZ 32768U /*!< Board xtal32K frequency in Hz */ - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes default configuration of clocks. - * - */ -void BOARD_InitBootClocks(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO12M ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK 12000000U /*!< Core clock frequency: 12000000Hz */ -#define BOARD_BOOTCLOCKFRO12M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFRO12M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF48M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ -#define BOARD_BOOTCLOCKFROHF48M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFROHF48M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF144M ******************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK 144000000U /*!< Core clock frequency: 144000000Hz */ -#define BOARD_BOOTCLOCKFROHF144M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFROHF144M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL150M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKPLL150M_CORE_CLOCK 150000000U /*!< Core clock frequency: 150000000Hz */ -#define BOARD_BOOTCLOCKPLL150M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockPLL150M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL100M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKPLL100M_CORE_CLOCK 100000000U /*!< Core clock frequency: 100000000Hz */ -#define BOARD_BOOTCLOCKPLL100M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockPLL100M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/mcx/boards/bunny-brain/pin_mux.c b/hw/bsp/mcx/boards/bunny-brain/pin_mux.c deleted file mode 100644 index acc2f3e45..000000000 --- a/hw/bsp/mcx/boards/bunny-brain/pin_mux.c +++ /dev/null @@ -1,141 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Pins v12.0 -processor: MCXN947 -package_id: MCXN947VDF -mcu_data: ksdk2_0 -processor_version: 0.12.3 - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -#include "fsl_common.h" -#include "fsl_port.h" -#include "pin_mux.h" - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitBootPins - * Description : Calls initialization functions. - * - * END ****************************************************************************************************************/ -void BOARD_InitBootPins(void) -{ - BOARD_InitPins(); -} - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -BOARD_InitPins: -- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'} -- pin_list: - - {pin_num: A1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P0, pin_signal: PIO1_8/WUU0_IN10/LPTMR1_ALT3/TRACE_DATA0/FC4_P0/FC5_P4/CT_INP8/SCT0_OUT2/FLEXIO0_D16/PLU_OUT0/ENET0_TXD2/I3C1_SDA/TSI0_CH17/ADC1_A8, - slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, pull_value: low, input_buffer: enable, - invert_input: normal} - - {pin_num: B1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P1, pin_signal: PIO1_9/TRACE_DATA1/FC4_P1/FC5_P5/CT_INP9/SCT0_OUT3/FLEXIO0_D17/PLU_OUT1/ENET0_TXD3/I3C1_SCL/TSI0_CH18/ADC1_A9, - slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, input_buffer: enable, invert_input: normal} - - {pin_num: F14, peripheral: GPIO3, signal: 'GPIO, 4', pin_signal: PIO3_4/FC7_P2/CT_INP18/PWM0_X2/FLEXIO0_D12/SIM1_CLK, slew_rate: fast, open_drain: disable, drive_strength: low, - pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitPins - * Description : Configures pin routing and optionally pin electrical features. - * - * END ****************************************************************************************************************/ -void BOARD_InitPins(void) -{ - /* Enables the clock for PORT1: Enables clock */ - CLOCK_EnableClock(kCLOCK_Port1); - /* Enables the clock for PORT3: Enables clock */ - CLOCK_EnableClock(kCLOCK_Port3); - - const port_pin_config_t port1_8_pinA1_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as FC4_P0 */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT1_8 (pin A1) is configured as FC4_P0 */ - PORT_SetPinConfig(PORT1, 8U, &port1_8_pinA1_config); - - const port_pin_config_t port1_9_pinB1_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as FC4_P1 */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT1_9 (pin B1) is configured as FC4_P1 */ - PORT_SetPinConfig(PORT1, 9U, &port1_9_pinB1_config); - - const port_pin_config_t port3_4_pinF14_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as PIO3_4 */ - kPORT_MuxAlt0, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT3_4 (pin F14) is configured as PIO3_4 */ - PORT_SetPinConfig(PORT3, 4U, &port3_4_pinF14_config); -} -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/hw/bsp/mcx/boards/bunny-brain/pin_mux.h b/hw/bsp/mcx/boards/bunny-brain/pin_mux.h deleted file mode 100644 index 40968c275..000000000 --- a/hw/bsp/mcx/boards/bunny-brain/pin_mux.h +++ /dev/null @@ -1,51 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _PIN_MUX_H_ -#define _PIN_MUX_H_ - -/*! - * @addtogroup pin_mux - * @{ - */ - -/*********************************************************************************************************************** - * API - **********************************************************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif - -/*! - * @brief Calls initialization functions. - * - */ -void BOARD_InitBootPins(void); - -/*! - * @brief Configures pin routing and optionally pin electrical features. - * - */ -void BOARD_InitPins(void); - -#if defined(__cplusplus) -} -#endif - -/*! - * @} - */ -#endif /* _PIN_MUX_H_ */ - -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/hw/bsp/mcx/boards/frdm-mcxn947/board.cmake b/hw/bsp/mcx/boards/frdm-mcxn947/board.cmake deleted file mode 100644 index 8c3280743..000000000 --- a/hw/bsp/mcx/boards/frdm-mcxn947/board.cmake +++ /dev/null @@ -1,21 +0,0 @@ -set(MCU_VARIANT MCXN947) -set(MCU_CORE MCXN947_cm33_core0) - -set(JLINK_DEVICE MCXN947_M33_0) -set(PYOCD_TARGET MCXN947) -set(NXPLINK_DEVICE MCXN947:MCXN947) - -set(PORT 1) - -function(update_board TARGET) - target_compile_definitions(${TARGET} PUBLIC - CPU_MCXN947VDF_cm33_core0 - BOARD_TUD_RHPORT=${PORT} - # port 0 is fullspeed, port 1 is highspeed - BOARD_TUD_MAX_SPEED=$ - ) - target_sources(${TARGET} PUBLIC - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/clock_config.c - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/pin_mux.c - ) -endfunction() diff --git a/hw/bsp/mcx/boards/frdm-mcxn947/board.h b/hw/bsp/mcx/boards/frdm-mcxn947/board.h deleted file mode 100644 index acb73363f..000000000 --- a/hw/bsp/mcx/boards/frdm-mcxn947/board.h +++ /dev/null @@ -1,66 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#ifndef BOARD_H_ -#define BOARD_H_ - -#ifdef __cplusplus - extern "C" { -#endif - -// LED -#define LED_GPIO GPIO0 -#define LED_CLK kCLOCK_Gpio0 -#define LED_PIN 10 // red -#define LED_STATE_ON 0 - -// WAKE button (Dummy, use unused pin -#define BUTTON_GPIO GPIO0 -#define BUTTON_CLK kCLOCK_Gpio0 -#define BUTTON_PIN 23 -#define BUTTON_STATE_ACTIVE 0 - -// UART -#define UART_DEV LPUART4 - -static inline void board_uart_init_clock(void) { - /* attach FRO 12M to FLEXCOMM4 */ - CLOCK_SetClkDiv(kCLOCK_DivFlexcom4Clk, 1u); - CLOCK_AttachClk(kFRO12M_to_FLEXCOMM4); - RESET_ClearPeripheralReset(kFC4_RST_SHIFT_RSTn); -} - -//#define UART_RX_PINMUX 0, 24, IOCON_PIO_DIG_FUNC1_EN -//#define UART_TX_PINMUX 0, 25, IOCON_PIO_DIG_FUNC1_EN - -// XTAL -#define XTAL0_CLK_HZ (24 * 1000 * 1000U) - -#ifdef __cplusplus - } -#endif - -#endif diff --git a/hw/bsp/mcx/boards/frdm-mcxn947/board.mk b/hw/bsp/mcx/boards/frdm-mcxn947/board.mk deleted file mode 100644 index aaad5e73e..000000000 --- a/hw/bsp/mcx/boards/frdm-mcxn947/board.mk +++ /dev/null @@ -1,11 +0,0 @@ -MCU_VARIANT = MCXN947 -MCU_CORE = MCXN947_cm33_core0 -PORT ?= 1 - -CFLAGS += -DCPU_MCXN947VDF_cm33_core0 - -JLINK_DEVICE = MCXN947_M33_0 -PYOCD_TARGET = MCXN947 - -# flash using pyocd -flash: flash-jlink diff --git a/hw/bsp/mcx/boards/frdm-mcxn947/clock_config.c b/hw/bsp/mcx/boards/frdm-mcxn947/clock_config.c deleted file mode 100644 index 37d2b4dfc..000000000 --- a/hw/bsp/mcx/boards/frdm-mcxn947/clock_config.c +++ /dev/null @@ -1,338 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ -/* - * How to setup clock using clock driver functions: - * - * 1. Setup clock sources. - * - * 2. Set up wait states of the flash. - * - * 3. Set up all dividers. - * - * 4. Set up all selectors to provide selected clocks. - * - */ - -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Clocks v10.0 -processor: MCXN947 -package_id: MCXN947VDF -mcu_data: ksdk2_0 -processor_version: 0.12.3 -board: MCX-N9XX-EVK - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -#include "clock_config.h" -#include "fsl_clock.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ - -/******************************************************************************* - * Variables - ******************************************************************************/ -/* System clock frequency. */ -// extern uint32_t SystemCoreClock; - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ -void BOARD_InitBootClocks(void) -{ - BOARD_BootClockPLL150M(); -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO12M ********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFRO12M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: MAIN_clock.outFreq, value: 12 MHz} -- {id: Slow_clock.outFreq, value: 3 MHz} -- {id: System_clock.outFreq, value: 12 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SCGMode, value: SIRC} -- {id: SCG.SCSSEL.sel, value: SCG.SIRC} -- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -void BOARD_BootClockFRO12M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO12M */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK; -} - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF48M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFROHF48M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 48 MHz} -- {id: Slow_clock.outFreq, value: 12 MHz} -- {id: System_clock.outFreq, value: 48 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -void BOARD_BootClockFROHF48M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK; -} - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF144M ******************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFROHF144M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 144 MHz} -- {id: MAIN_clock.outFreq, value: 144 MHz} -- {id: Slow_clock.outFreq, value: 18 MHz} -- {id: System_clock.outFreq, value: 72 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true} -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} -sources: -- {id: SCG.FIRC.outFreq, value: 144 MHz} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -void BOARD_BootClockFROHF144M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(144000000U); /*!< Enable FRO HF(144MHz) output */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 2U); /*!< Set AHBCLKDIV divider to value 2 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK; -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL150M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockPLL150M -called_from_default_init: true -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 150 MHz} -- {id: PLL0_CLK_clock.outFreq, value: 150 MHz} -- {id: Slow_clock.outFreq, value: 37.5 MHz} -- {id: System_clock.outFreq, value: 150 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: PLL0_Mode, value: Normal} -- {id: RunPowerMode, value: OD} -- {id: SCGMode, value: PLL0} -- {id: SCG.PLL0M_MULT.scale, value: '50', locked: true} -- {id: SCG.PLL0SRCSEL.sel, value: SCG.FIRC_48M} -- {id: SCG.PLL0_NDIV.scale, value: '8', locked: true} -- {id: SCG.SCSSEL.sel, value: SCG.PLL0_CLK} -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -void BOARD_BootClockPLL150M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - /*!< Set up PLL0 */ - const pll_setup_t pll0Setup = { - .pllctrl = SCG_APLLCTRL_SOURCE(1U) | SCG_APLLCTRL_SELI(27U) | SCG_APLLCTRL_SELP(13U), - .pllndiv = SCG_APLLNDIV_NDIV(8U), - .pllpdiv = SCG_APLLPDIV_PDIV(1U), - .pllmdiv = SCG_APLLMDIV_MDIV(50U), - .pllRate = 150000000U - }; - CLOCK_SetPLL0Freq(&pll0Setup); /*!< Configure PLL0 to the desired values */ - CLOCK_SetPll0MonitorMode(kSCG_Pll0MonitorDisable); /* Pll0 Monitor is disabled */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kPLL0_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL0 */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKPLL150M_CORE_CLOCK; -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL100M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockPLL100M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: CLK_IN_clock.outFreq, value: 24 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: MAIN_clock.outFreq, value: 100 MHz} -- {id: PLL1_CLK_clock.outFreq, value: 100 MHz} -- {id: Slow_clock.outFreq, value: 25 MHz} -- {id: System_clock.outFreq, value: 100 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: PLL1_Mode, value: Normal} -- {id: SCGMode, value: PLL1} -- {id: SCG.PLL1M_MULT.scale, value: '100', locked: true} -- {id: SCG.PLL1_NDIV.scale, value: '6', locked: true} -- {id: SCG.PLL1_PDIV.scale, value: '4', locked: true} -- {id: SCG.SCSSEL.sel, value: SCG.PLL1_CLK} -- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} -- {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} -sources: -- {id: SCG.SOSC.outFreq, value: 24 MHz, enabled: true} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -void BOARD_BootClockPLL100M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupExtClocking(24000000U); - CLOCK_SetSysOscMonitorMode(kSCG_SysOscMonitorDisable); /* System OSC Clock Monitor is disabled */ - - /*!< Set up PLL1 */ - const pll_setup_t pll1Setup = { - .pllctrl = SCG_SPLLCTRL_SOURCE(0U) | SCG_SPLLCTRL_SELI(53U) | SCG_SPLLCTRL_SELP(26U), - .pllndiv = SCG_SPLLNDIV_NDIV(6U), - .pllpdiv = SCG_SPLLPDIV_PDIV(2U), - .pllmdiv = SCG_SPLLMDIV_MDIV(100U), - .pllRate = 100000000U - }; - CLOCK_SetPLL1Freq(&pll1Setup); /*!< Configure PLL1 to the desired values */ - CLOCK_SetPll1MonitorMode(kSCG_Pll1MonitorDisable); /* Pll1 Monitor is disabled */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kPLL1_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL1 */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKPLL100M_CORE_CLOCK; -} diff --git a/hw/bsp/mcx/boards/frdm-mcxn947/clock_config.h b/hw/bsp/mcx/boards/frdm-mcxn947/clock_config.h deleted file mode 100644 index c238a0423..000000000 --- a/hw/bsp/mcx/boards/frdm-mcxn947/clock_config.h +++ /dev/null @@ -1,177 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _CLOCK_CONFIG_H_ -#define _CLOCK_CONFIG_H_ - -#include "fsl_common.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ -#define BOARD_XTAL0_CLK_HZ 24000000U /*!< Board xtal frequency in Hz */ -#define BOARD_XTAL32K_CLK_HZ 32768U /*!< Board xtal32K frequency in Hz */ - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes default configuration of clocks. - * - */ -void BOARD_InitBootClocks(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO12M ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK 12000000U /*!< Core clock frequency: 12000000Hz */ -#define BOARD_BOOTCLOCKFRO12M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFRO12M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF48M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ -#define BOARD_BOOTCLOCKFROHF48M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFROHF48M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF144M ******************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK 144000000U /*!< Core clock frequency: 144000000Hz */ -#define BOARD_BOOTCLOCKFROHF144M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFROHF144M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL150M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKPLL150M_CORE_CLOCK 150000000U /*!< Core clock frequency: 150000000Hz */ -#define BOARD_BOOTCLOCKPLL150M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockPLL150M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL100M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKPLL100M_CORE_CLOCK 100000000U /*!< Core clock frequency: 100000000Hz */ -#define BOARD_BOOTCLOCKPLL100M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockPLL100M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.c b/hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.c deleted file mode 100644 index 30a5ae456..000000000 --- a/hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.c +++ /dev/null @@ -1,143 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Pins v12.0 -processor: MCXN947 -package_id: MCXN947VDF -mcu_data: ksdk2_0 -processor_version: 0.12.3 - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -#include "fsl_common.h" -#include "fsl_port.h" -#include "pin_mux.h" - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitBootPins - * Description : Calls initialization functions. - * - * END ****************************************************************************************************************/ -void BOARD_InitBootPins(void) -{ - BOARD_InitPins(); -} - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -BOARD_InitPins: -- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'} -- pin_list: - - {pin_num: A1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P0, pin_signal: PIO1_8/WUU0_IN10/LPTMR1_ALT3/TRACE_DATA0/FC4_P0/FC5_P4/CT_INP8/SCT0_OUT2/FLEXIO0_D16/PLU_OUT0/ENET0_TXD2/I3C1_SDA/TSI0_CH17/ADC1_A8, - slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, pull_value: low, input_buffer: enable, - invert_input: normal} - - {pin_num: B1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P1, pin_signal: PIO1_9/TRACE_DATA1/FC4_P1/FC5_P5/CT_INP9/SCT0_OUT3/FLEXIO0_D17/PLU_OUT1/ENET0_TXD3/I3C1_SCL/TSI0_CH18/ADC1_A9, - slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, input_buffer: enable, invert_input: normal} - - {pin_num: B12, peripheral: GPIO0, signal: 'GPIO, 10', pin_signal: PIO0_12/ADC0_B10/FC0_P6/CT0O_MAT0/FLEXIO0_D2, slew_rate: fast, open_drain: disable, drive_strength: low, - pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitPins - * Description : Configures pin routing and optionally pin electrical features. - * - * END ****************************************************************************************************************/ -void BOARD_InitPins(void) -{ - /* Enables the clock for PORT0: Enables clock */ - CLOCK_EnableClock(kCLOCK_Port0); - - /* Enables the clock for PORT1: Enables clock */ - CLOCK_EnableClock(kCLOCK_Port1); - - - const port_pin_config_t port1_8_pinA1_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as FC4_P0 */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT1_8 (pin A1) is configured as FC4_P0 */ - PORT_SetPinConfig(PORT1, 8U, &port1_8_pinA1_config); - - const port_pin_config_t port1_9_pinB1_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as FC4_P1 */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT1_9 (pin B1) is configured as FC4_P1 */ - PORT_SetPinConfig(PORT1, 9U, &port1_9_pinB1_config); - - const port_pin_config_t port0_10_pinB12_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as PIO0_10 */ - kPORT_MuxAlt0, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT0_10 (pin B12) is configured as PIO0_10 */ - PORT_SetPinConfig(PORT0, 10U, &port0_10_pinB12_config); -} -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.h b/hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.h deleted file mode 100644 index 40968c275..000000000 --- a/hw/bsp/mcx/boards/frdm-mcxn947/pin_mux.h +++ /dev/null @@ -1,51 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _PIN_MUX_H_ -#define _PIN_MUX_H_ - -/*! - * @addtogroup pin_mux - * @{ - */ - -/*********************************************************************************************************************** - * API - **********************************************************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif - -/*! - * @brief Calls initialization functions. - * - */ -void BOARD_InitBootPins(void); - -/*! - * @brief Configures pin routing and optionally pin electrical features. - * - */ -void BOARD_InitPins(void); - -#if defined(__cplusplus) -} -#endif - -/*! - * @} - */ -#endif /* _PIN_MUX_H_ */ - -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/src/class/audio/audio_device.c b/src/class/audio/audio_device.c index d438d0715..4adc558a6 100644 --- a/src/class/audio/audio_device.c +++ b/src/class/audio/audio_device.c @@ -1729,7 +1729,7 @@ static bool audiod_set_interface(uint8_t rhport, tusb_control_request_t const * // Find correct interface if (tu_desc_type(p_desc) == TUSB_DESC_INTERFACE && ((tusb_desc_interface_t const * )p_desc)->bInterfaceNumber == itf && ((tusb_desc_interface_t const * )p_desc)->bAlternateSetting == alt) { -#if CFG_TUD_AUDIO_ENABLE_ENCODING || CFG_TUD_AUDIO_ENABLE_DECODING || CFG_TUD_AUDIO_EP_IN_FLOW_CONTROL +#if (CFG_TUD_AUDIO_ENABLE_EP_IN && (CFG_TUD_AUDIO_EP_IN_FLOW_CONTROL || CFG_TUD_AUDIO_ENABLE_ENCODING)) || (CFG_TUD_AUDIO_ENABLE_EP_OUT && CFG_TUD_AUDIO_ENABLE_DECODING) uint8_t const * p_desc_parse_for_params = p_desc; #endif // From this point forward follow the EP descriptors associated to the current alternate setting interface - Open EPs if necessary diff --git a/src/class/cdc/cdc.h b/src/class/cdc/cdc.h index deec32ae4..5cbd658fe 100644 --- a/src/class/cdc/cdc.h +++ b/src/class/cdc/cdc.h @@ -136,8 +136,7 @@ typedef enum{ //--------------------------------------------------------------------+ /// Communication Interface Management Element Request Codes -typedef enum -{ +typedef enum { CDC_REQUEST_SEND_ENCAPSULATED_COMMAND = 0x00, ///< is used to issue a command in the format of the supported control protocol of the Communications Class interface CDC_REQUEST_GET_ENCAPSULATED_RESPONSE = 0x01, ///< is used to request a response in the format of the supported control protocol of the Communications Class interface. CDC_REQUEST_SET_COMM_FEATURE = 0x02, @@ -180,39 +179,38 @@ typedef enum CDC_REQUEST_GET_ATM_VC_STATISTICS = 0x53, CDC_REQUEST_MDLM_SEMANTIC_MODEL = 0x60, -}cdc_management_request_t; +} cdc_management_request_t; -enum { +typedef enum { CDC_CONTROL_LINE_STATE_DTR = 0x01, CDC_CONTROL_LINE_STATE_RTS = 0x02, -}; +} cdc_control_line_state_t; -enum { +typedef enum { CDC_LINE_CODING_STOP_BITS_1 = 0, // 1 bit CDC_LINE_CODING_STOP_BITS_1_5 = 1, // 1.5 bits CDC_LINE_CODING_STOP_BITS_2 = 2, // 2 bits -}; +} cdc_line_coding_stopbits_t; // TODO Backward compatible for typos. Maybe removed in the future release #define CDC_LINE_CONDING_STOP_BITS_1 CDC_LINE_CODING_STOP_BITS_1 #define CDC_LINE_CONDING_STOP_BITS_1_5 CDC_LINE_CODING_STOP_BITS_1_5 #define CDC_LINE_CONDING_STOP_BITS_2 CDC_LINE_CODING_STOP_BITS_2 -enum { +typedef enum { CDC_LINE_CODING_PARITY_NONE = 0, CDC_LINE_CODING_PARITY_ODD = 1, CDC_LINE_CODING_PARITY_EVEN = 2, CDC_LINE_CODING_PARITY_MARK = 3, CDC_LINE_CODING_PARITY_SPACE = 4, -}; +} cdc_line_coding_parity_t; //--------------------------------------------------------------------+ // Management Element Notification (Notification Endpoint) //--------------------------------------------------------------------+ /// 6.3 Notification Codes -typedef enum -{ +typedef enum { CDC_NOTIF_NETWORK_CONNECTION = 0x00, ///< This notification allows the device to notify the host about network connection status. CDC_NOTIF_RESPONSE_AVAILABLE = 0x01, ///< This notification allows the device to notify the hostthat a response is available. This response can be retrieved with a subsequent \ref CDC_REQUEST_GET_ENCAPSULATED_RESPONSE request. CDC_NOTIF_AUX_JACK_HOOK_STATE = 0x08, diff --git a/src/class/cdc/cdc_host.c b/src/class/cdc/cdc_host.c index 2463671c6..2fb37d835 100644 --- a/src/class/cdc/cdc_host.c +++ b/src/class/cdc/cdc_host.c @@ -22,6 +22,9 @@ * THE SOFTWARE. * * This file is part of the TinyUSB stack. + * + * Contribution + * - Heiko Kuester: CH34x support */ #include "tusb_option.h" @@ -50,12 +53,18 @@ typedef struct { uint8_t bInterfaceSubClass; uint8_t bInterfaceProtocol; + uint8_t ep_notif; uint8_t serial_drid; // Serial Driver ID + bool mounted; // Enumeration is complete cdc_acm_capability_t acm_capability; - uint8_t ep_notif; - uint8_t line_state; // DTR (bit0), RTS (bit1) TU_ATTR_ALIGNED(4) cdc_line_coding_t line_coding; // Baudrate, stop bits, parity, data width + uint8_t line_state; // DTR (bit0), RTS (bit1) + + #if CFG_TUH_CDC_FTDI || CFG_TUH_CDC_CP210X || CFG_TUH_CDC_CH34X + cdc_line_coding_t requested_line_coding; + // 1 byte padding + #endif tuh_xfer_cb_t user_control_cb; @@ -69,7 +78,6 @@ typedef struct { uint8_t rx_ff_buf[CFG_TUH_CDC_TX_BUFSIZE]; CFG_TUH_MEM_ALIGN uint8_t rx_ep_buf[CFG_TUH_CDC_TX_EPSIZE]; } stream; - } cdch_interface_t; CFG_TUH_MEM_SECTION @@ -83,45 +91,57 @@ static cdch_interface_t cdch_data[CFG_TUH_CDC]; static bool acm_open(uint8_t daddr, tusb_desc_interface_t const *itf_desc, uint16_t max_len); static void acm_process_config(tuh_xfer_t* xfer); +static bool acm_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool acm_set_data_format(cdch_interface_t* p_cdc, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, tuh_xfer_cb_t complete_cb, uintptr_t user_data); static bool acm_set_line_coding(cdch_interface_t* p_cdc, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data); static bool acm_set_control_line_state(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data); -static bool acm_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data); //------------- FTDI prototypes -------------// #if CFG_TUH_CDC_FTDI #include "serial/ftdi_sio.h" -static uint16_t const ftdi_vid_pid_list[][2] = {CFG_TUH_CDC_FTDI_VID_PID_LIST }; -enum { - FTDI_PID_COUNT = sizeof(ftdi_vid_pid_list) / sizeof(ftdi_vid_pid_list[0]) -}; - -// Store last request baudrate since divisor to baudrate is not easy -static uint32_t _ftdi_requested_baud; +static uint16_t const ftdi_vid_pid_list[][2] = {CFG_TUH_CDC_FTDI_VID_PID_LIST}; static bool ftdi_open(uint8_t daddr, const tusb_desc_interface_t *itf_desc, uint16_t max_len); static void ftdi_process_config(tuh_xfer_t* xfer); -static bool ftdi_sio_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data); static bool ftdi_sio_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool ftdi_set_data_format(cdch_interface_t* p_cdc, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool ftdi_set_line_coding(cdch_interface_t* p_cdc, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool ftdi_sio_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data); #endif //------------- CP210X prototypes -------------// #if CFG_TUH_CDC_CP210X #include "serial/cp210x.h" -static uint16_t const cp210x_vid_pid_list[][2] = {CFG_TUH_CDC_CP210X_VID_PID_LIST }; -enum { - CP210X_PID_COUNT = sizeof(cp210x_vid_pid_list) / sizeof(cp210x_vid_pid_list[0]) -}; +static uint16_t const cp210x_vid_pid_list[][2] = {CFG_TUH_CDC_CP210X_VID_PID_LIST}; static bool cp210x_open(uint8_t daddr, tusb_desc_interface_t const *itf_desc, uint16_t max_len); static void cp210x_process_config(tuh_xfer_t* xfer); -static bool cp210x_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data); static bool cp210x_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool cp210x_set_data_format(cdch_interface_t* p_cdc, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool cp210x_set_line_coding(cdch_interface_t* p_cdc, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool cp210x_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data); #endif +//------------- CH34x prototypes -------------// +#if CFG_TUH_CDC_CH34X +#include "serial/ch34x.h" + +static uint16_t const ch34x_vid_pid_list[][2] = {CFG_TUH_CDC_CH34X_VID_PID_LIST}; + +static bool ch34x_open(uint8_t daddr, tusb_desc_interface_t const* itf_desc, uint16_t max_len); +static void ch34x_process_config(tuh_xfer_t* xfer); + +static bool ch34x_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool ch34x_set_data_format(cdch_interface_t* p_cdc, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool ch34x_set_line_coding(cdch_interface_t* p_cdc, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +static bool ch34x_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data); +#endif + +//------------- Common -------------// enum { SERIAL_DRIVER_ACM = 0, @@ -132,60 +152,96 @@ enum { #if CFG_TUH_CDC_CP210X SERIAL_DRIVER_CP210X, #endif + +#if CFG_TUH_CDC_CH34X + SERIAL_DRIVER_CH34X, +#endif + + SERIAL_DRIVER_COUNT }; typedef struct { + uint16_t const (*vid_pid_list)[2]; + uint16_t const vid_pid_count; + bool (*const open)(uint8_t daddr, const tusb_desc_interface_t *itf_desc, uint16_t max_len); void (*const process_set_config)(tuh_xfer_t* xfer); bool (*const set_control_line_state)(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data); bool (*const set_baudrate)(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data); + bool (*const set_data_format)(cdch_interface_t* p_cdc, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, tuh_xfer_cb_t complete_cb, uintptr_t user_data); + bool (*const set_line_coding)(cdch_interface_t* p_cdc, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data); } cdch_serial_driver_t; // Note driver list must be in the same order as SERIAL_DRIVER enum static const cdch_serial_driver_t serial_drivers[] = { - { .process_set_config = acm_process_config, - .set_control_line_state = acm_set_control_line_state, - .set_baudrate = acm_set_baudrate + { + .vid_pid_list = NULL, + .vid_pid_count = 0, + .open = acm_open, + .process_set_config = acm_process_config, + .set_control_line_state = acm_set_control_line_state, + .set_baudrate = acm_set_baudrate, + .set_data_format = acm_set_data_format, + .set_line_coding = acm_set_line_coding }, #if CFG_TUH_CDC_FTDI - { .process_set_config = ftdi_process_config, - .set_control_line_state = ftdi_sio_set_modem_ctrl, - .set_baudrate = ftdi_sio_set_baudrate + { + .vid_pid_list = ftdi_vid_pid_list, + .vid_pid_count = TU_ARRAY_SIZE(ftdi_vid_pid_list), + .open = ftdi_open, + .process_set_config = ftdi_process_config, + .set_control_line_state = ftdi_sio_set_modem_ctrl, + .set_baudrate = ftdi_sio_set_baudrate, + .set_data_format = ftdi_set_data_format, + .set_line_coding = ftdi_set_line_coding }, #endif #if CFG_TUH_CDC_CP210X - { .process_set_config = cp210x_process_config, - .set_control_line_state = cp210x_set_modem_ctrl, - .set_baudrate = cp210x_set_baudrate + { + .vid_pid_list = cp210x_vid_pid_list, + .vid_pid_count = TU_ARRAY_SIZE(cp210x_vid_pid_list), + .open = cp210x_open, + .process_set_config = cp210x_process_config, + .set_control_line_state = cp210x_set_modem_ctrl, + .set_baudrate = cp210x_set_baudrate, + .set_data_format = cp210x_set_data_format, + .set_line_coding = cp210x_set_line_coding }, #endif -}; -enum { - SERIAL_DRIVER_COUNT = sizeof(serial_drivers) / sizeof(serial_drivers[0]) + #if CFG_TUH_CDC_CH34X + { + .vid_pid_list = ch34x_vid_pid_list, + .vid_pid_count = TU_ARRAY_SIZE(ch34x_vid_pid_list), + .open = ch34x_open, + .process_set_config = ch34x_process_config, + .set_control_line_state = ch34x_set_modem_ctrl, + .set_baudrate = ch34x_set_baudrate, + .set_data_format = ch34x_set_data_format, + .set_line_coding = ch34x_set_line_coding + }, + #endif }; +TU_VERIFY_STATIC(TU_ARRAY_SIZE(serial_drivers) == SERIAL_DRIVER_COUNT, "Serial driver count mismatch"); + //--------------------------------------------------------------------+ // INTERNAL OBJECT & FUNCTION DECLARATION //--------------------------------------------------------------------+ -static inline cdch_interface_t* get_itf(uint8_t idx) -{ +static inline cdch_interface_t* get_itf(uint8_t idx) { TU_ASSERT(idx < CFG_TUH_CDC, NULL); cdch_interface_t* p_cdc = &cdch_data[idx]; return (p_cdc->daddr != 0) ? p_cdc : NULL; } -static inline uint8_t get_idx_by_ep_addr(uint8_t daddr, uint8_t ep_addr) -{ - for(uint8_t i=0; idaddr == daddr) && - (ep_addr == p_cdc->ep_notif || ep_addr == p_cdc->stream.rx.ep_addr || ep_addr == p_cdc->stream.tx.ep_addr)) - { + (ep_addr == p_cdc->ep_notif || ep_addr == p_cdc->stream.rx.ep_addr || ep_addr == p_cdc->stream.tx.ep_addr)) { return i; } } @@ -193,14 +249,10 @@ static inline uint8_t get_idx_by_ep_addr(uint8_t daddr, uint8_t ep_addr) return TUSB_INDEX_INVALID_8; } - -static cdch_interface_t* make_new_itf(uint8_t daddr, tusb_desc_interface_t const *itf_desc) -{ - for(uint8_t i=0; idaddr = daddr; p_cdc->bInterfaceNumber = itf_desc->bInterfaceNumber; p_cdc->bInterfaceSubClass = itf_desc->bInterfaceSubClass; @@ -221,20 +273,16 @@ static void cdch_internal_control_complete(tuh_xfer_t* xfer); // APPLICATION API //--------------------------------------------------------------------+ -uint8_t tuh_cdc_itf_get_index(uint8_t daddr, uint8_t itf_num) -{ - for(uint8_t i=0; idaddr == daddr && p_cdc->bInterfaceNumber == itf_num) return i; } return TUSB_INDEX_INVALID_8; } -bool tuh_cdc_itf_get_info(uint8_t idx, tuh_itf_info_t* info) -{ +bool tuh_cdc_itf_get_info(uint8_t idx, tuh_itf_info_t* info) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc && info); @@ -256,30 +304,27 @@ bool tuh_cdc_itf_get_info(uint8_t idx, tuh_itf_info_t* info) return true; } -bool tuh_cdc_mounted(uint8_t idx) -{ +bool tuh_cdc_mounted(uint8_t idx) { cdch_interface_t* p_cdc = get_itf(idx); - return p_cdc != NULL; + TU_VERIFY(p_cdc); + return p_cdc->mounted; } -bool tuh_cdc_get_dtr(uint8_t idx) -{ +bool tuh_cdc_get_dtr(uint8_t idx) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); return (p_cdc->line_state & CDC_CONTROL_LINE_STATE_DTR) ? true : false; } -bool tuh_cdc_get_rts(uint8_t idx) -{ +bool tuh_cdc_get_rts(uint8_t idx) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); return (p_cdc->line_state & CDC_CONTROL_LINE_STATE_RTS) ? true : false; } -bool tuh_cdc_get_local_line_coding(uint8_t idx, cdc_line_coding_t* line_coding) -{ +bool tuh_cdc_get_local_line_coding(uint8_t idx, cdc_line_coding_t* line_coding) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); @@ -292,32 +337,28 @@ bool tuh_cdc_get_local_line_coding(uint8_t idx, cdc_line_coding_t* line_coding) // Write //--------------------------------------------------------------------+ -uint32_t tuh_cdc_write(uint8_t idx, void const* buffer, uint32_t bufsize) -{ +uint32_t tuh_cdc_write(uint8_t idx, void const* buffer, uint32_t bufsize) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); return tu_edpt_stream_write(&p_cdc->stream.tx, buffer, bufsize); } -uint32_t tuh_cdc_write_flush(uint8_t idx) -{ +uint32_t tuh_cdc_write_flush(uint8_t idx) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); return tu_edpt_stream_write_xfer(&p_cdc->stream.tx); } -bool tuh_cdc_write_clear(uint8_t idx) -{ +bool tuh_cdc_write_clear(uint8_t idx) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); return tu_edpt_stream_clear(&p_cdc->stream.tx); } -uint32_t tuh_cdc_write_available(uint8_t idx) -{ +uint32_t tuh_cdc_write_available(uint8_t idx) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); @@ -328,32 +369,28 @@ uint32_t tuh_cdc_write_available(uint8_t idx) // Read //--------------------------------------------------------------------+ -uint32_t tuh_cdc_read (uint8_t idx, void* buffer, uint32_t bufsize) -{ +uint32_t tuh_cdc_read (uint8_t idx, void* buffer, uint32_t bufsize) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); return tu_edpt_stream_read(&p_cdc->stream.rx, buffer, bufsize); } -uint32_t tuh_cdc_read_available(uint8_t idx) -{ +uint32_t tuh_cdc_read_available(uint8_t idx) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); return tu_edpt_stream_read_available(&p_cdc->stream.rx); } -bool tuh_cdc_peek(uint8_t idx, uint8_t* ch) -{ +bool tuh_cdc_peek(uint8_t idx, uint8_t* ch) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); return tu_edpt_stream_peek(&p_cdc->stream.rx, ch); } -bool tuh_cdc_read_clear (uint8_t idx) -{ +bool tuh_cdc_read_clear (uint8_t idx) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc); @@ -366,28 +403,25 @@ bool tuh_cdc_read_clear (uint8_t idx) // Control Endpoint API //--------------------------------------------------------------------+ -// internal control complete to update state such as line state, encoding -static void cdch_internal_control_complete(tuh_xfer_t* xfer) -{ - uint8_t const itf_num = (uint8_t) tu_le16toh(xfer->setup->wIndex); +static void process_internal_control_complete(tuh_xfer_t* xfer, uint8_t itf_num) { uint8_t idx = tuh_cdc_itf_get_index(xfer->daddr, itf_num); cdch_interface_t* p_cdc = get_itf(idx); TU_ASSERT(p_cdc, ); + uint16_t const value = tu_le16toh(xfer->setup->wValue); - if (xfer->result == XFER_RESULT_SUCCESS) - { + if (xfer->result == XFER_RESULT_SUCCESS) { switch (p_cdc->serial_drid) { case SERIAL_DRIVER_ACM: switch (xfer->setup->bRequest) { case CDC_REQUEST_SET_CONTROL_LINE_STATE: - p_cdc->line_state = (uint8_t) tu_le16toh(xfer->setup->wValue); + p_cdc->line_state = (uint8_t) value; break; case CDC_REQUEST_SET_LINE_CODING: { uint16_t const len = tu_min16(sizeof(cdc_line_coding_t), tu_le16toh(xfer->setup->wLength)); memcpy(&p_cdc->line_coding, xfer->buffer, len); - } break; + } default: break; } @@ -397,12 +431,11 @@ static void cdch_internal_control_complete(tuh_xfer_t* xfer) case SERIAL_DRIVER_FTDI: switch (xfer->setup->bRequest) { case FTDI_SIO_MODEM_CTRL: - p_cdc->line_state = (uint8_t) (tu_le16toh(xfer->setup->wValue) & 0x00ff); + p_cdc->line_state = (uint8_t) value; break; case FTDI_SIO_SET_BAUD_RATE: - // convert from divisor to baudrate is not supported - p_cdc->line_coding.bit_rate = _ftdi_requested_baud; + p_cdc->line_coding.bit_rate = p_cdc->requested_line_coding.bit_rate; break; default: break; @@ -414,15 +447,61 @@ static void cdch_internal_control_complete(tuh_xfer_t* xfer) case SERIAL_DRIVER_CP210X: switch(xfer->setup->bRequest) { case CP210X_SET_MHS: - p_cdc->line_state = (uint8_t) (tu_le16toh(xfer->setup->wValue) & 0x00ff); + p_cdc->line_state = (uint8_t) value; break; case CP210X_SET_BAUDRATE: { uint32_t baudrate; memcpy(&baudrate, xfer->buffer, sizeof(uint32_t)); p_cdc->line_coding.bit_rate = tu_le32toh(baudrate); + break; } + + default: break; + } + break; + #endif + + #if CFG_TUH_CDC_CH34X + case SERIAL_DRIVER_CH34X: + switch (xfer->setup->bRequest) { + case CH34X_REQ_WRITE_REG: + // register write request + switch (value) { + case CH34X_REG16_DIVISOR_PRESCALER: + // baudrate + p_cdc->line_coding.bit_rate = p_cdc->requested_line_coding.bit_rate; + break; + + case CH32X_REG16_LCR2_LCR: + // data format + p_cdc->line_coding.stop_bits = p_cdc->requested_line_coding.stop_bits; + p_cdc->line_coding.parity = p_cdc->requested_line_coding.parity; + p_cdc->line_coding.data_bits = p_cdc->requested_line_coding.data_bits; + break; + + default: break; + } + break; + + case CH34X_REQ_MODEM_CTRL: { + // set modem controls RTS/DTR request. Note: signals are inverted + uint16_t const modem_signal = ~value; + if (modem_signal & CH34X_BIT_RTS) { + p_cdc->line_state |= CDC_CONTROL_LINE_STATE_RTS; + } else { + p_cdc->line_state &= (uint8_t) ~CDC_CONTROL_LINE_STATE_RTS; + } + + if (modem_signal & CH34X_BIT_DTR) { + p_cdc->line_state |= CDC_CONTROL_LINE_STATE_DTR; + } else { + p_cdc->line_state &= (uint8_t) ~CDC_CONTROL_LINE_STATE_DTR; + } break; + } + + default: break; } break; #endif @@ -437,14 +516,20 @@ static void cdch_internal_control_complete(tuh_xfer_t* xfer) } } +// internal control complete to update state such as line state, encoding +static void cdch_internal_control_complete(tuh_xfer_t* xfer) { + uint8_t const itf_num = (uint8_t) tu_le16toh(xfer->setup->wIndex); + process_internal_control_complete(xfer, itf_num); +} + bool tuh_cdc_set_control_line_state(uint8_t idx, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { cdch_interface_t* p_cdc = get_itf(idx); TU_VERIFY(p_cdc && p_cdc->serial_drid < SERIAL_DRIVER_COUNT); cdch_serial_driver_t const* driver = &serial_drivers[p_cdc->serial_drid]; - if ( complete_cb ) { + if (complete_cb) { return driver->set_control_line_state(p_cdc, line_state, complete_cb, user_data); - }else { + } else { // blocking xfer_result_t result = XFER_RESULT_INVALID; bool ret = driver->set_control_line_state(p_cdc, line_state, complete_cb, (uintptr_t) &result); @@ -455,7 +540,6 @@ bool tuh_cdc_set_control_line_state(uint8_t idx, uint16_t line_state, tuh_xfer_c } TU_VERIFY(ret && result == XFER_RESULT_SUCCESS); - p_cdc->line_state = (uint8_t) line_state; return true; } @@ -466,9 +550,9 @@ bool tuh_cdc_set_baudrate(uint8_t idx, uint32_t baudrate, tuh_xfer_cb_t complete TU_VERIFY(p_cdc && p_cdc->serial_drid < SERIAL_DRIVER_COUNT); cdch_serial_driver_t const* driver = &serial_drivers[p_cdc->serial_drid]; - if ( complete_cb ) { + if (complete_cb) { return driver->set_baudrate(p_cdc, baudrate, complete_cb, user_data); - }else { + } else { // blocking xfer_result_t result = XFER_RESULT_INVALID; bool ret = driver->set_baudrate(p_cdc, baudrate, complete_cb, (uintptr_t) &result); @@ -479,25 +563,23 @@ bool tuh_cdc_set_baudrate(uint8_t idx, uint32_t baudrate, tuh_xfer_cb_t complete } TU_VERIFY(ret && result == XFER_RESULT_SUCCESS); - p_cdc->line_coding.bit_rate = baudrate; return true; } } -bool tuh_cdc_set_line_coding(uint8_t idx, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data) -{ +bool tuh_cdc_set_data_format(uint8_t idx, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { cdch_interface_t* p_cdc = get_itf(idx); - // only ACM support this set line coding request - TU_VERIFY(p_cdc && p_cdc->serial_drid == SERIAL_DRIVER_ACM); - TU_VERIFY(p_cdc->acm_capability.support_line_request); + TU_VERIFY(p_cdc && p_cdc->serial_drid < SERIAL_DRIVER_COUNT); + cdch_serial_driver_t const* driver = &serial_drivers[p_cdc->serial_drid]; - if ( complete_cb ) { - return acm_set_line_coding(p_cdc, line_coding, complete_cb, user_data); - }else { + if (complete_cb) { + return driver->set_data_format(p_cdc, stop_bits, parity, data_bits, complete_cb, user_data); + } else { // blocking xfer_result_t result = XFER_RESULT_INVALID; - bool ret = acm_set_line_coding(p_cdc, line_coding, complete_cb, (uintptr_t) &result); + bool ret = driver->set_data_format(p_cdc, stop_bits, parity, data_bits, complete_cb, (uintptr_t) &result); if (user_data) { // user_data is not NULL, return result via user_data @@ -505,7 +587,31 @@ bool tuh_cdc_set_line_coding(uint8_t idx, cdc_line_coding_t const* line_coding, } TU_VERIFY(ret && result == XFER_RESULT_SUCCESS); + p_cdc->line_coding.stop_bits = stop_bits; + p_cdc->line_coding.parity = parity; + p_cdc->line_coding.data_bits = data_bits; + return true; + } +} + +bool tuh_cdc_set_line_coding(uint8_t idx, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + cdch_interface_t* p_cdc = get_itf(idx); + TU_VERIFY(p_cdc && p_cdc->serial_drid < SERIAL_DRIVER_COUNT); + cdch_serial_driver_t const* driver = &serial_drivers[p_cdc->serial_drid]; + + if ( complete_cb ) { + return driver->set_line_coding(p_cdc, line_coding, complete_cb, user_data); + } else { + // blocking + xfer_result_t result = XFER_RESULT_INVALID; + bool ret = driver->set_line_coding(p_cdc, line_coding, complete_cb, (uintptr_t) &result); + + if (user_data) { + // user_data is not NULL, return result via user_data + *((xfer_result_t*) user_data) = result; + } + TU_VERIFY(ret && result == XFER_RESULT_SUCCESS); p_cdc->line_coding = *line_coding; return true; } @@ -515,39 +621,34 @@ bool tuh_cdc_set_line_coding(uint8_t idx, cdc_line_coding_t const* line_coding, // CLASS-USBH API //--------------------------------------------------------------------+ -void cdch_init(void) -{ +void cdch_init(void) { tu_memclr(cdch_data, sizeof(cdch_data)); - for(size_t i=0; istream.tx, true, true, false, - p_cdc->stream.tx_ff_buf, CFG_TUH_CDC_TX_BUFSIZE, - p_cdc->stream.tx_ep_buf, CFG_TUH_CDC_TX_EPSIZE); + p_cdc->stream.tx_ff_buf, CFG_TUH_CDC_TX_BUFSIZE, + p_cdc->stream.tx_ep_buf, CFG_TUH_CDC_TX_EPSIZE); tu_edpt_stream_init(&p_cdc->stream.rx, true, false, false, - p_cdc->stream.rx_ff_buf, CFG_TUH_CDC_RX_BUFSIZE, - p_cdc->stream.rx_ep_buf, CFG_TUH_CDC_RX_EPSIZE); + p_cdc->stream.rx_ff_buf, CFG_TUH_CDC_RX_BUFSIZE, + p_cdc->stream.rx_ep_buf, CFG_TUH_CDC_RX_EPSIZE); } } -void cdch_close(uint8_t daddr) -{ - for(uint8_t idx=0; idxdaddr == daddr) - { + if (p_cdc->daddr == daddr) { TU_LOG_DRV(" CDCh close addr = %u index = %u\r\n", daddr, idx); // Invoke application callback if (tuh_cdc_umount_cb) tuh_cdc_umount_cb(idx); - //tu_memclr(p_cdc, sizeof(cdch_interface_t)); p_cdc->daddr = 0; p_cdc->bInterfaceNumber = 0; + p_cdc->mounted = false; tu_edpt_stream_close(&p_cdc->stream.tx); tu_edpt_stream_close(&p_cdc->stream.rx); } @@ -571,16 +672,11 @@ bool cdch_xfer_cb(uint8_t daddr, uint8_t ep_addr, xfer_result_t event, uint32_t // - xferred_bytes is multiple of EP Packet size and not zero tu_edpt_stream_write_zlp_if_needed(&p_cdc->stream.tx, xferred_bytes); } - } - else if ( ep_addr == p_cdc->stream.rx.ep_addr ) { + } else if ( ep_addr == p_cdc->stream.rx.ep_addr ) { #if CFG_TUH_CDC_FTDI if (p_cdc->serial_drid == SERIAL_DRIVER_FTDI) { // FTDI reserve 2 bytes for status - // FTDI status -// uint8_t status[2] = { -// p_cdc->stream.rx.ep_buf[0], -// p_cdc->stream.rx.ep_buf[1] -// }; + // uint8_t status[2] = {p_cdc->stream.rx.ep_buf[0], p_cdc->stream.rx.ep_buf[1]}; tu_edpt_stream_read_xfer_complete_offset(&p_cdc->stream.rx, xferred_bytes, 2); }else #endif @@ -606,20 +702,15 @@ bool cdch_xfer_cb(uint8_t daddr, uint8_t ep_addr, xfer_result_t event, uint32_t // Enumeration //--------------------------------------------------------------------+ -static bool open_ep_stream_pair(cdch_interface_t* p_cdc, tusb_desc_endpoint_t const *desc_ep) -{ - for(size_t i=0; i<2; i++) - { +static bool open_ep_stream_pair(cdch_interface_t* p_cdc, tusb_desc_endpoint_t const* desc_ep) { + for (size_t i = 0; i < 2; i++) { TU_ASSERT(TUSB_DESC_ENDPOINT == desc_ep->bDescriptorType && - TUSB_XFER_BULK == desc_ep->bmAttributes.xfer); - + TUSB_XFER_BULK == desc_ep->bmAttributes.xfer); TU_ASSERT(tuh_edpt_open(p_cdc->daddr, desc_ep)); - if ( tu_edpt_dir(desc_ep->bEndpointAddress) == TUSB_DIR_IN ) - { + if (tu_edpt_dir(desc_ep->bEndpointAddress) == TUSB_DIR_IN) { tu_edpt_stream_open(&p_cdc->stream.rx, p_cdc->daddr, desc_ep); - }else - { + } else { tu_edpt_stream_open(&p_cdc->stream.tx, p_cdc->daddr, desc_ep); } @@ -629,45 +720,36 @@ static bool open_ep_stream_pair(cdch_interface_t* p_cdc, tusb_desc_endpoint_t co return true; } -bool cdch_open(uint8_t rhport, uint8_t daddr, tusb_desc_interface_t const *itf_desc, uint16_t max_len) -{ +bool cdch_open(uint8_t rhport, uint8_t daddr, tusb_desc_interface_t const *itf_desc, uint16_t max_len) { (void) rhport; - // Only support ACM subclass + // For CDC: only support ACM subclass // Note: Protocol 0xFF can be RNDIS device - if ( TUSB_CLASS_CDC == itf_desc->bInterfaceClass && - CDC_COMM_SUBCLASS_ABSTRACT_CONTROL_MODEL == itf_desc->bInterfaceSubClass) - { + if (TUSB_CLASS_CDC == itf_desc->bInterfaceClass && + CDC_COMM_SUBCLASS_ABSTRACT_CONTROL_MODEL == itf_desc->bInterfaceSubClass) { return acm_open(daddr, itf_desc, max_len); } - #if CFG_TUH_CDC_FTDI || CFG_TUH_CDC_CP210X - else if ( TUSB_CLASS_VENDOR_SPECIFIC == itf_desc->bInterfaceClass ) - { + else if (SERIAL_DRIVER_COUNT > 1 && + TUSB_CLASS_VENDOR_SPECIFIC == itf_desc->bInterfaceClass) { uint16_t vid, pid; TU_VERIFY(tuh_vid_pid_get(daddr, &vid, &pid)); - #if CFG_TUH_CDC_FTDI - for (size_t i = 0; i < FTDI_PID_COUNT; i++) { - if (ftdi_vid_pid_list[i][0] == vid && ftdi_vid_pid_list[i][1] == pid) { - return ftdi_open(daddr, itf_desc, max_len); - } - } - #endif - - #if CFG_TUH_CDC_CP210X - for (size_t i = 0; i < CP210X_PID_COUNT; i++) { - if (cp210x_vid_pid_list[i][0] == vid && cp210x_vid_pid_list[i][1] == pid) { - return cp210x_open(daddr, itf_desc, max_len); + for (size_t dr = 1; dr < SERIAL_DRIVER_COUNT; dr++) { + cdch_serial_driver_t const* driver = &serial_drivers[dr]; + for (size_t i = 0; i < driver->vid_pid_count; i++) { + if (driver->vid_pid_list[i][0] == vid && driver->vid_pid_list[i][1] == pid) { + return driver->open(daddr, itf_desc, max_len); + } } } - #endif } - #endif return false; } static void set_config_complete(cdch_interface_t * p_cdc, uint8_t idx, uint8_t itf_num) { + TU_LOG_DRV("CDCh Set Configure complete\r\n"); + p_cdc->mounted = true; if (tuh_cdc_mount_cb) tuh_cdc_mount_cb(idx); // Prepare for incoming data @@ -677,9 +759,7 @@ static void set_config_complete(cdch_interface_t * p_cdc, uint8_t idx, uint8_t i usbh_driver_set_config_complete(p_cdc->daddr, itf_num); } - -bool cdch_set_config(uint8_t daddr, uint8_t itf_num) -{ +bool cdch_set_config(uint8_t daddr, uint8_t itf_num) { tusb_control_request_t request; request.wIndex = tu_htole16((uint16_t) itf_num); @@ -708,94 +788,84 @@ enum { CONFIG_ACM_COMPLETE, }; -static bool acm_open(uint8_t daddr, tusb_desc_interface_t const *itf_desc, uint16_t max_len) -{ - uint8_t const * p_desc_end = ((uint8_t const*) itf_desc) + max_len; +static bool acm_open(uint8_t daddr, tusb_desc_interface_t const* itf_desc, uint16_t max_len) { + uint8_t const* p_desc_end = ((uint8_t const*) itf_desc) + max_len; - cdch_interface_t * p_cdc = make_new_itf(daddr, itf_desc); + cdch_interface_t* p_cdc = make_new_itf(daddr, itf_desc); TU_VERIFY(p_cdc); - p_cdc->serial_drid = SERIAL_DRIVER_ACM; //------------- Control Interface -------------// - uint8_t const * p_desc = tu_desc_next(itf_desc); + uint8_t const* p_desc = tu_desc_next(itf_desc); // Communication Functional Descriptors - while( (p_desc < p_desc_end) && (TUSB_DESC_CS_INTERFACE == tu_desc_type(p_desc)) ) - { - if ( CDC_FUNC_DESC_ABSTRACT_CONTROL_MANAGEMENT == cdc_functional_desc_typeof(p_desc) ) - { + while ((p_desc < p_desc_end) && (TUSB_DESC_CS_INTERFACE == tu_desc_type(p_desc))) { + if (CDC_FUNC_DESC_ABSTRACT_CONTROL_MANAGEMENT == cdc_functional_desc_typeof(p_desc)) { // save ACM bmCapabilities - p_cdc->acm_capability = ((cdc_desc_func_acm_t const *) p_desc)->bmCapabilities; + p_cdc->acm_capability = ((cdc_desc_func_acm_t const*) p_desc)->bmCapabilities; } p_desc = tu_desc_next(p_desc); } // Open notification endpoint of control interface if any - if (itf_desc->bNumEndpoints == 1) - { + if (itf_desc->bNumEndpoints == 1) { TU_ASSERT(TUSB_DESC_ENDPOINT == tu_desc_type(p_desc)); - tusb_desc_endpoint_t const * desc_ep = (tusb_desc_endpoint_t const *) p_desc; + tusb_desc_endpoint_t const* desc_ep = (tusb_desc_endpoint_t const*) p_desc; - TU_ASSERT( tuh_edpt_open(daddr, desc_ep) ); + TU_ASSERT(tuh_edpt_open(daddr, desc_ep)); p_cdc->ep_notif = desc_ep->bEndpointAddress; p_desc = tu_desc_next(p_desc); } //------------- Data Interface (if any) -------------// - if ( (TUSB_DESC_INTERFACE == tu_desc_type(p_desc)) && - (TUSB_CLASS_CDC_DATA == ((tusb_desc_interface_t const *) p_desc)->bInterfaceClass) ) - { + if ((TUSB_DESC_INTERFACE == tu_desc_type(p_desc)) && + (TUSB_CLASS_CDC_DATA == ((tusb_desc_interface_t const*) p_desc)->bInterfaceClass)) { // next to endpoint descriptor p_desc = tu_desc_next(p_desc); // data endpoints expected to be in pairs - TU_ASSERT(open_ep_stream_pair(p_cdc, (tusb_desc_endpoint_t const *) p_desc)); + TU_ASSERT(open_ep_stream_pair(p_cdc, (tusb_desc_endpoint_t const*) p_desc)); } return true; } -static void acm_process_config(tuh_xfer_t* xfer) -{ +static void acm_process_config(tuh_xfer_t* xfer) { uintptr_t const state = xfer->user_data; uint8_t const itf_num = (uint8_t) tu_le16toh(xfer->setup->wIndex); uint8_t const idx = tuh_cdc_itf_get_index(xfer->daddr, itf_num); - cdch_interface_t * p_cdc = get_itf(idx); - TU_ASSERT(p_cdc, ); + cdch_interface_t* p_cdc = get_itf(idx); + TU_ASSERT(p_cdc,); - switch(state) - { + switch (state) { case CONFIG_ACM_SET_CONTROL_LINE_STATE: #if CFG_TUH_CDC_LINE_CONTROL_ON_ENUM - if (p_cdc->acm_capability.support_line_request) - { - TU_ASSERT(acm_set_control_line_state(p_cdc, CFG_TUH_CDC_LINE_CONTROL_ON_ENUM, acm_process_config, - CONFIG_ACM_SET_LINE_CODING), ); + if (p_cdc->acm_capability.support_line_request) { + TU_ASSERT(acm_set_control_line_state(p_cdc, CFG_TUH_CDC_LINE_CONTROL_ON_ENUM, acm_process_config, CONFIG_ACM_SET_LINE_CODING),); break; } - #endif + #endif TU_ATTR_FALLTHROUGH; case CONFIG_ACM_SET_LINE_CODING: - #ifdef CFG_TUH_CDC_LINE_CODING_ON_ENUM - if (p_cdc->acm_capability.support_line_request) - { + #ifdef CFG_TUH_CDC_LINE_CODING_ON_ENUM + if (p_cdc->acm_capability.support_line_request) { cdc_line_coding_t line_coding = CFG_TUH_CDC_LINE_CODING_ON_ENUM; - TU_ASSERT(acm_set_line_coding(p_cdc, &line_coding, acm_process_config, CONFIG_ACM_COMPLETE), ); + TU_ASSERT(acm_set_line_coding(p_cdc, &line_coding, acm_process_config, CONFIG_ACM_COMPLETE),); break; } - #endif + #endif TU_ATTR_FALLTHROUGH; case CONFIG_ACM_COMPLETE: // itf_num+1 to account for data interface as well - set_config_complete(p_cdc, idx, itf_num+1); + set_config_complete(p_cdc, idx, itf_num + 1); break; - default: break; + default: + break; } } @@ -863,6 +933,19 @@ static bool acm_set_line_coding(cdch_interface_t* p_cdc, cdc_line_coding_t const return true; } +static bool acm_set_data_format(cdch_interface_t* p_cdc, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + TU_LOG_DRV("CDC ACM Set Data Format\r\n"); + + cdc_line_coding_t line_coding; + line_coding.bit_rate = p_cdc->line_coding.bit_rate; + line_coding.stop_bits = stop_bits; + line_coding.parity = parity; + line_coding.data_bits = data_bits; + + return acm_set_line_coding(p_cdc, &line_coding, complete_cb, user_data); +} + static bool acm_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { TU_VERIFY(p_cdc->acm_capability.support_line_request); cdc_line_coding_t line_coding = p_cdc->line_coding; @@ -892,7 +975,6 @@ static bool ftdi_open(uint8_t daddr, const tusb_desc_interface_t *itf_desc, uint TU_VERIFY(p_cdc); TU_LOG_DRV("FTDI opened\r\n"); - p_cdc->serial_drid = SERIAL_DRIVER_FTDI; // endpoint pair @@ -928,13 +1010,32 @@ static bool ftdi_sio_set_request(cdch_interface_t* p_cdc, uint8_t command, uint1 return tuh_control_xfer(&xfer); } -static bool ftdi_sio_reset(cdch_interface_t* p_cdc, tuh_xfer_cb_t complete_cb, uintptr_t user_data) -{ +static bool ftdi_sio_reset(cdch_interface_t* p_cdc, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { return ftdi_sio_set_request(p_cdc, FTDI_SIO_RESET, FTDI_SIO_RESET_SIO, complete_cb, user_data); } -static bool ftdi_sio_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data) -{ +static bool ftdi_set_data_format(cdch_interface_t* p_cdc, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + (void) p_cdc; + (void) stop_bits; + (void) parity; + (void) data_bits; + (void) complete_cb; + (void) user_data; + // TODO not implemented yet + return false; +} + +static bool ftdi_set_line_coding(cdch_interface_t* p_cdc, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + (void) p_cdc; + (void) line_coding; + (void) complete_cb; + (void) user_data; + // TODO not implemented yet + return false; +} + +static bool ftdi_sio_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { TU_LOG_DRV("CDC FTDI Set Control Line State\r\n"); p_cdc->user_control_cb = complete_cb; TU_ASSERT(ftdi_sio_set_request(p_cdc, FTDI_SIO_MODEM_CTRL, 0x0300 | line_state, @@ -942,8 +1043,7 @@ static bool ftdi_sio_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state return true; } -static uint32_t ftdi_232bm_baud_base_to_divisor(uint32_t baud, uint32_t base) -{ +static uint32_t ftdi_232bm_baud_base_to_divisor(uint32_t baud, uint32_t base) { const uint8_t divfrac[8] = { 0, 3, 2, 4, 1, 5, 6, 7 }; uint32_t divisor; @@ -963,18 +1063,16 @@ static uint32_t ftdi_232bm_baud_base_to_divisor(uint32_t baud, uint32_t base) return divisor; } -static uint32_t ftdi_232bm_baud_to_divisor(uint32_t baud) -{ +static uint32_t ftdi_232bm_baud_to_divisor(uint32_t baud) { return ftdi_232bm_baud_base_to_divisor(baud, 48000000u); } -static bool ftdi_sio_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data) -{ +static bool ftdi_sio_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { uint16_t const divisor = (uint16_t) ftdi_232bm_baud_to_divisor(baudrate); TU_LOG_DRV("CDC FTDI Set BaudRate = %lu, divisor = 0x%04x\r\n", baudrate, divisor); p_cdc->user_control_cb = complete_cb; - _ftdi_requested_baud = baudrate; + p_cdc->requested_line_coding.bit_rate = baudrate; TU_ASSERT(ftdi_sio_set_request(p_cdc, FTDI_SIO_SET_BAUD_RATE, divisor, complete_cb ? cdch_internal_control_complete : NULL, user_data)); @@ -996,8 +1094,7 @@ static void ftdi_process_config(tuh_xfer_t* xfer) { case CONFIG_FTDI_MODEM_CTRL: #if CFG_TUH_CDC_LINE_CONTROL_ON_ENUM - TU_ASSERT( - ftdi_sio_set_modem_ctrl(p_cdc, CFG_TUH_CDC_LINE_CONTROL_ON_ENUM, ftdi_process_config, CONFIG_FTDI_SET_BAUDRATE),); + TU_ASSERT(ftdi_sio_set_modem_ctrl(p_cdc, CFG_TUH_CDC_LINE_CONTROL_ON_ENUM, ftdi_process_config, CONFIG_FTDI_SET_BAUDRATE),); break; #else TU_ATTR_FALLTHROUGH; @@ -1105,6 +1202,15 @@ static bool cp210x_ifc_enable(cdch_interface_t* p_cdc, uint16_t enabled, tuh_xfe return cp210x_set_request(p_cdc, CP210X_IFC_ENABLE, enabled, NULL, 0, complete_cb, user_data); } +static bool cp210x_set_line_coding(cdch_interface_t* p_cdc, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + // TODO implement later + (void) p_cdc; + (void) line_coding; + (void) complete_cb; + (void) user_data; + return false; +} + static bool cp210x_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { TU_LOG_DRV("CDC CP210x Set BaudRate = %lu\r\n", baudrate); uint32_t baud_le = tu_htole32(baudrate); @@ -1113,8 +1219,19 @@ static bool cp210x_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, tuh_ complete_cb ? cdch_internal_control_complete : NULL, user_data); } -static bool cp210x_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data) -{ +static bool cp210x_set_data_format(cdch_interface_t* p_cdc, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + (void) p_cdc; + (void) stop_bits; + (void) parity; + (void) data_bits; + (void) complete_cb; + (void) user_data; + // TODO not implemented yet + return false; +} + +static bool cp210x_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { TU_LOG_DRV("CDC CP210x Set Control Line State\r\n"); p_cdc->user_control_cb = complete_cb; return cp210x_set_request(p_cdc, CP210X_SET_MHS, 0x0300 | line_state, NULL, 0, @@ -1154,8 +1271,7 @@ static void cp210x_process_config(tuh_xfer_t* xfer) { case CONFIG_CP210X_SET_DTR_RTS: #if CFG_TUH_CDC_LINE_CONTROL_ON_ENUM - TU_ASSERT( - cp210x_set_modem_ctrl(p_cdc, CFG_TUH_CDC_LINE_CONTROL_ON_ENUM, cp210x_process_config, CONFIG_CP210X_COMPLETE),); + TU_ASSERT(cp210x_set_modem_ctrl(p_cdc, CFG_TUH_CDC_LINE_CONTROL_ON_ENUM, cp210x_process_config, CONFIG_CP210X_COMPLETE),); break; #else TU_ATTR_FALLTHROUGH; @@ -1171,4 +1287,374 @@ static void cp210x_process_config(tuh_xfer_t* xfer) { #endif +//--------------------------------------------------------------------+ +// CH34x (CH340 & CH341) +//--------------------------------------------------------------------+ + +#if CFG_TUH_CDC_CH34X + +static uint8_t ch34x_get_lcr(uint8_t stop_bits, uint8_t parity, uint8_t data_bits); +static uint16_t ch34x_get_divisor_prescaler(uint32_t baval); + +//------------- control request -------------// + +static bool ch34x_set_request(cdch_interface_t* p_cdc, uint8_t direction, uint8_t request, uint16_t value, + uint16_t index, uint8_t* buffer, uint16_t length, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + tusb_control_request_t const request_setup = { + .bmRequestType_bit = { + .recipient = TUSB_REQ_RCPT_DEVICE, + .type = TUSB_REQ_TYPE_VENDOR, + .direction = direction & 0x01u + }, + .bRequest = request, + .wValue = tu_htole16 (value), + .wIndex = tu_htole16 (index), + .wLength = tu_htole16 (length) + }; + + // use usbh enum buf since application variable does not live long enough + uint8_t* enum_buf = NULL; + + if (buffer && length > 0) { + enum_buf = usbh_get_enum_buf(); + if (direction == TUSB_DIR_OUT) { + tu_memcpy_s(enum_buf, CFG_TUH_ENUMERATION_BUFSIZE, buffer, length); + } + } + + tuh_xfer_t xfer = { + .daddr = p_cdc->daddr, + .ep_addr = 0, + .setup = &request_setup, + .buffer = enum_buf, + .complete_cb = complete_cb, + .user_data = user_data + }; + + return tuh_control_xfer(&xfer); +} + +static inline bool ch34x_control_out(cdch_interface_t* p_cdc, uint8_t request, uint16_t value, uint16_t index, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + return ch34x_set_request(p_cdc, TUSB_DIR_OUT, request, value, index, NULL, 0, complete_cb, user_data); +} + +static inline bool ch34x_control_in(cdch_interface_t* p_cdc, uint8_t request, uint16_t value, uint16_t index, + uint8_t* buffer, uint16_t buffersize, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + return ch34x_set_request(p_cdc, TUSB_DIR_IN, request, value, index, buffer, buffersize, + complete_cb, user_data); +} + +static inline bool ch34x_write_reg(cdch_interface_t* p_cdc, uint16_t reg, uint16_t reg_value, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + return ch34x_control_out(p_cdc, CH34X_REQ_WRITE_REG, reg, reg_value, complete_cb, user_data); +} + +//static bool ch34x_read_reg_request ( cdch_interface_t* p_cdc, uint16_t reg, +// uint8_t *buffer, uint16_t buffersize, tuh_xfer_cb_t complete_cb, uintptr_t user_data ) +//{ +// return ch34x_control_in ( p_cdc, CH34X_REQ_READ_REG, reg, 0, buffer, buffersize, complete_cb, user_data ); +//} + +static bool ch34x_write_reg_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + uint16_t const div_ps = ch34x_get_divisor_prescaler(baudrate); + TU_VERIFY(div_ps); + TU_ASSERT(ch34x_write_reg(p_cdc, CH34X_REG16_DIVISOR_PRESCALER, div_ps, + complete_cb, user_data)); + return true; +} + +//------------- Driver API -------------// + +// internal control complete to update state such as line state, encoding +static void ch34x_control_complete(tuh_xfer_t* xfer) { + // CH34x only has 1 interface and use wIndex as payload and not for bInterfaceNumber + process_internal_control_complete(xfer, 0); +} + +static bool ch34x_set_data_format(cdch_interface_t* p_cdc, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + p_cdc->requested_line_coding.stop_bits = stop_bits; + p_cdc->requested_line_coding.parity = parity; + p_cdc->requested_line_coding.data_bits = data_bits; + + uint8_t const lcr = ch34x_get_lcr(stop_bits, parity, data_bits); + TU_VERIFY(lcr); + TU_ASSERT (ch34x_control_out(p_cdc, CH34X_REQ_WRITE_REG, CH32X_REG16_LCR2_LCR, lcr, + complete_cb ? ch34x_control_complete : NULL, user_data)); + return true; +} + +static bool ch34x_set_baudrate(cdch_interface_t* p_cdc, uint32_t baudrate, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + p_cdc->requested_line_coding.bit_rate = baudrate; + p_cdc->user_control_cb = complete_cb; + TU_ASSERT(ch34x_write_reg_baudrate(p_cdc, baudrate, + complete_cb ? ch34x_control_complete : NULL, user_data)); + return true; +} + +static void ch34x_set_line_coding_stage1_complete(tuh_xfer_t* xfer) { + // CH34x only has 1 interface and use wIndex as payload and not for bInterfaceNumber + uint8_t const itf_num = 0; + uint8_t const idx = tuh_cdc_itf_get_index(xfer->daddr, itf_num); + cdch_interface_t* p_cdc = get_itf(idx); + TU_ASSERT(p_cdc, ); + + if (xfer->result == XFER_RESULT_SUCCESS) { + // stage 1 success, continue to stage 2 + p_cdc->line_coding.bit_rate = p_cdc->requested_line_coding.bit_rate; + TU_ASSERT(ch34x_set_data_format(p_cdc, p_cdc->requested_line_coding.stop_bits, p_cdc->requested_line_coding.parity, + p_cdc->requested_line_coding.data_bits, ch34x_control_complete, xfer->user_data), ); + } else { + // stage 1 failed, notify user + xfer->complete_cb = p_cdc->user_control_cb; + if (xfer->complete_cb) { + xfer->complete_cb(xfer); + } + } +} + +// 2 stages: set baudrate (stage1) + set data format (stage2) +static bool ch34x_set_line_coding(cdch_interface_t* p_cdc, cdc_line_coding_t const* line_coding, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + p_cdc->requested_line_coding = *line_coding; + p_cdc->user_control_cb = complete_cb; + + if (complete_cb) { + // stage 1 set baudrate + TU_ASSERT(ch34x_write_reg_baudrate(p_cdc, line_coding->bit_rate, + ch34x_set_line_coding_stage1_complete, user_data)); + } else { + // sync call + xfer_result_t result; + + // stage 1 set baudrate + TU_ASSERT(ch34x_write_reg_baudrate(p_cdc, line_coding->bit_rate, NULL, (uintptr_t) &result)); + TU_VERIFY(result == XFER_RESULT_SUCCESS); + p_cdc->line_coding.bit_rate = line_coding->bit_rate; + + // stage 2 set data format + TU_ASSERT(ch34x_set_data_format(p_cdc, line_coding->stop_bits, line_coding->parity, line_coding->data_bits, + NULL, (uintptr_t) &result)); + TU_VERIFY(result == XFER_RESULT_SUCCESS); + p_cdc->line_coding.stop_bits = line_coding->stop_bits; + p_cdc->line_coding.parity = line_coding->parity; + p_cdc->line_coding.data_bits = line_coding->data_bits; + + // update transfer result, user_data is expected to point to xfer_result_t + if (user_data) { + *((xfer_result_t*) user_data) = result; + } + } + + return true; +} + +static bool ch34x_set_modem_ctrl(cdch_interface_t* p_cdc, uint16_t line_state, + tuh_xfer_cb_t complete_cb, uintptr_t user_data) { + uint8_t control = 0; + if (line_state & CDC_CONTROL_LINE_STATE_RTS) { + control |= CH34X_BIT_RTS; + } + if (line_state & CDC_CONTROL_LINE_STATE_DTR) { + control |= CH34X_BIT_DTR; + } + + // CH34x signals are inverted + control = ~control; + + p_cdc->user_control_cb = complete_cb; + TU_ASSERT (ch34x_control_out(p_cdc, CH34X_REQ_MODEM_CTRL, control, 0, + complete_cb ? ch34x_control_complete : NULL, user_data)); + return true; +} + +//------------- Enumeration -------------// +enum { + CONFIG_CH34X_READ_VERSION = 0, + CONFIG_CH34X_SERIAL_INIT, + CONFIG_CH34X_SPECIAL_REG_WRITE, + CONFIG_CH34X_FLOW_CONTROL, + CONFIG_CH34X_MODEM_CONTROL, + CONFIG_CH34X_COMPLETE +}; + +static bool ch34x_open(uint8_t daddr, tusb_desc_interface_t const* itf_desc, uint16_t max_len) { + // CH34x Interface includes 1 vendor interface + 2 bulk + 1 interrupt endpoints + TU_VERIFY (itf_desc->bNumEndpoints == 3); + TU_VERIFY (sizeof(tusb_desc_interface_t) + 3 * sizeof(tusb_desc_endpoint_t) <= max_len); + + cdch_interface_t* p_cdc = make_new_itf(daddr, itf_desc); + TU_VERIFY (p_cdc); + + TU_LOG_DRV ("CH34x opened\r\n"); + p_cdc->serial_drid = SERIAL_DRIVER_CH34X; + + tusb_desc_endpoint_t const* desc_ep = (tusb_desc_endpoint_t const*) tu_desc_next(itf_desc); + + // data endpoints expected to be in pairs + TU_ASSERT(open_ep_stream_pair(p_cdc, desc_ep)); + desc_ep += 2; + + // Interrupt endpoint: not used for now + TU_ASSERT(TUSB_DESC_ENDPOINT == tu_desc_type(desc_ep) && + TUSB_XFER_INTERRUPT == desc_ep->bmAttributes.xfer); + TU_ASSERT(tuh_edpt_open(daddr, desc_ep)); + p_cdc->ep_notif = desc_ep->bEndpointAddress; + + return true; +} + +static void ch34x_process_config(tuh_xfer_t* xfer) { + // CH34x only has 1 interface and use wIndex as payload and not for bInterfaceNumber + uint8_t const itf_num = 0; + uint8_t const idx = tuh_cdc_itf_get_index(xfer->daddr, itf_num); + cdch_interface_t* p_cdc = get_itf(idx); + uintptr_t const state = xfer->user_data; + uint8_t buffer[2]; // TODO remove + TU_ASSERT (p_cdc,); + TU_ASSERT (xfer->result == XFER_RESULT_SUCCESS,); + + switch (state) { + case CONFIG_CH34X_READ_VERSION: + TU_LOG_DRV("[%u] CDCh CH34x attempt to read Chip Version\r\n", p_cdc->daddr); + TU_ASSERT (ch34x_control_in(p_cdc, CH34X_REQ_READ_VERSION, 0, 0, buffer, 2, ch34x_process_config, CONFIG_CH34X_SERIAL_INIT),); + break; + + case CONFIG_CH34X_SERIAL_INIT: { + // handle version read data, set CH34x line coding (incl. baudrate) + uint8_t const version = xfer->buffer[0]; + TU_LOG_DRV("[%u] CDCh CH34x Chip Version = %02x\r\n", p_cdc->daddr, version); + // only versions >= 0x30 are tested, below 0x30 seems having other programming, see drivers from WCH vendor, Linux kernel and FreeBSD + TU_ASSERT (version >= 0x30,); + // init CH34x with line coding + cdc_line_coding_t const line_coding = CFG_TUH_CDC_LINE_CODING_ON_ENUM_CH34X; + uint16_t const div_ps = ch34x_get_divisor_prescaler(line_coding.bit_rate); + TU_ASSERT(div_ps, ); + uint8_t const lcr = ch34x_get_lcr(line_coding.stop_bits, line_coding.parity, line_coding.data_bits); + TU_ASSERT(lcr, ); + TU_ASSERT (ch34x_control_out(p_cdc, CH34X_REQ_SERIAL_INIT, tu_u16(lcr, 0x9c), div_ps, + ch34x_process_config, CONFIG_CH34X_SPECIAL_REG_WRITE),); + break; + } + + case CONFIG_CH34X_SPECIAL_REG_WRITE: + // overtake line coding and do special reg write, purpose unknown, overtaken from WCH driver + p_cdc->line_coding = ((cdc_line_coding_t) CFG_TUH_CDC_LINE_CODING_ON_ENUM_CH34X); + TU_ASSERT (ch34x_write_reg(p_cdc, TU_U16(CH341_REG_0x0F, CH341_REG_0x2C), 0x0007, ch34x_process_config, CONFIG_CH34X_FLOW_CONTROL),); + break; + + case CONFIG_CH34X_FLOW_CONTROL: + // no hardware flow control + TU_ASSERT (ch34x_write_reg(p_cdc, TU_U16(CH341_REG_0x27, CH341_REG_0x27), 0x0000, ch34x_process_config, CONFIG_CH34X_MODEM_CONTROL),); + break; + + case CONFIG_CH34X_MODEM_CONTROL: + // !always! set modem controls RTS/DTR (CH34x has no reset state after CH34X_REQ_SERIAL_INIT) + TU_ASSERT (ch34x_set_modem_ctrl(p_cdc, CFG_TUH_CDC_LINE_CONTROL_ON_ENUM, ch34x_process_config, CONFIG_CH34X_COMPLETE),); + break; + + case CONFIG_CH34X_COMPLETE: + set_config_complete(p_cdc, idx, itf_num); + break; + + default: + TU_ASSERT (false,); + break; + } +} + +//------------- CH34x helper -------------// + +// calculate divisor and prescaler for baudrate, return it as 16-bit combined value +static uint16_t ch34x_get_divisor_prescaler(uint32_t baval) { + uint8_t a; + uint8_t b; + uint32_t c; + + TU_VERIFY(baval != 0 && baval <= 2000000, 0); + switch (baval) { + case 921600: + a = 0xf3; + b = 7; + break; + + case 307200: + a = 0xd9; + b = 7; + break; + + default: + if (baval > 6000000 / 255) { + b = 3; + c = 6000000; + } else if (baval > 750000 / 255) { + b = 2; + c = 750000; + } else if (baval > 93750 / 255) { + b = 1; + c = 93750; + } else { + b = 0; + c = 11719; + } + a = (uint8_t) (c / baval); + if (a == 0 || a == 0xFF) { + return 0; + } + if ((c / a - baval) > (baval - c / (a + 1))) { + a++; + } + a = (uint8_t) (256 - a); + break; + } + + // reg divisor = a, reg prescaler = b + // According to linux code we need to set bit 7 of UCHCOM_REG_BPS_PRE, + // otherwise the chip will buffer data. + return (uint16_t) ((uint16_t)a << 8 | 0x80 | b); +} + +// calculate lcr value from data coding +static uint8_t ch34x_get_lcr(uint8_t stop_bits, uint8_t parity, uint8_t data_bits) { + uint8_t lcr = CH34X_LCR_ENABLE_RX | CH34X_LCR_ENABLE_TX; + TU_VERIFY(data_bits >= 5 && data_bits <= 8, 0); + lcr |= (uint8_t) (data_bits - 5); + + switch(parity) { + case CDC_LINE_CODING_PARITY_NONE: + break; + + case CDC_LINE_CODING_PARITY_ODD: + lcr |= CH34X_LCR_ENABLE_PAR; + break; + + case CDC_LINE_CODING_PARITY_EVEN: + lcr |= CH34X_LCR_ENABLE_PAR | CH34X_LCR_PAR_EVEN; + break; + + case CDC_LINE_CODING_PARITY_MARK: + lcr |= CH34X_LCR_ENABLE_PAR | CH34X_LCR_MARK_SPACE; + break; + + case CDC_LINE_CODING_PARITY_SPACE: + lcr |= CH34X_LCR_ENABLE_PAR | CH34X_LCR_MARK_SPACE | CH34X_LCR_PAR_EVEN; + break; + + default: break; + } + + // 1.5 stop bits not supported + TU_VERIFY(stop_bits != CDC_LINE_CODING_STOP_BITS_1_5, 0); + if (stop_bits == CDC_LINE_CODING_STOP_BITS_2) { + lcr |= CH34X_LCR_STOP_BITS_2; + } + + return lcr; +} + + +#endif // CFG_TUH_CDC_CH34X + #endif diff --git a/src/class/cdc/cdc_host.h b/src/class/cdc/cdc_host.h index 9e5edd94e..d512a23a5 100644 --- a/src/class/cdc/cdc_host.h +++ b/src/class/cdc/cdc_host.h @@ -148,8 +148,11 @@ bool tuh_cdc_set_control_line_state(uint8_t idx, uint16_t line_state, tuh_xfer_c // Request to set baudrate bool tuh_cdc_set_baudrate(uint8_t idx, uint32_t baudrate, tuh_xfer_cb_t complete_cb, uintptr_t user_data); -// Request to Set Line Coding (ACM only) -// Should only use if you don't work with serial devices such as FTDI/CP210x +// Request to set data format +bool tuh_cdc_set_data_format(uint8_t idx, uint8_t stop_bits, uint8_t parity, uint8_t data_bits, tuh_xfer_cb_t complete_cb, uintptr_t user_data); + +// Request to Set Line Coding = baudrate + data format +// Note: only implemented by ACM and CH34x, not supported by FTDI and CP210x yet bool tuh_cdc_set_line_coding(uint8_t idx, cdc_line_coding_t const* line_coding, tuh_xfer_cb_t complete_cb, uintptr_t user_data); // Request to Get Line Coding (ACM only) @@ -159,15 +162,13 @@ bool tuh_cdc_set_line_coding(uint8_t idx, cdc_line_coding_t const* line_coding, // Connect by set both DTR, RTS TU_ATTR_ALWAYS_INLINE static inline -bool tuh_cdc_connect(uint8_t idx, tuh_xfer_cb_t complete_cb, uintptr_t user_data) -{ +bool tuh_cdc_connect(uint8_t idx, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { return tuh_cdc_set_control_line_state(idx, CDC_CONTROL_LINE_STATE_DTR | CDC_CONTROL_LINE_STATE_RTS, complete_cb, user_data); } // Disconnect by clear both DTR, RTS TU_ATTR_ALWAYS_INLINE static inline -bool tuh_cdc_disconnect(uint8_t idx, tuh_xfer_cb_t complete_cb, uintptr_t user_data) -{ +bool tuh_cdc_disconnect(uint8_t idx, tuh_xfer_cb_t complete_cb, uintptr_t user_data) { return tuh_cdc_set_control_line_state(idx, 0x00, complete_cb, user_data); } diff --git a/src/class/cdc/serial/ch34x.h b/src/class/cdc/serial/ch34x.h new file mode 100644 index 000000000..c18066f57 --- /dev/null +++ b/src/class/cdc/serial/ch34x.h @@ -0,0 +1,84 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Heiko Kuester + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _CH34X_H_ +#define _CH34X_H_ + +// There is no official documentation for the CH34x (CH340, CH341) chips. Reference can be found +// - https://github.com/WCHSoftGroup/ch341ser_linux +// - https://github.com/torvalds/linux/blob/master/drivers/usb/serial/ch341.c +// - https://github.com/freebsd/freebsd-src/blob/main/sys/dev/usb/serial/uchcom.c + +// set line_coding @ enumeration +#ifdef CFG_TUH_CDC_LINE_CODING_ON_ENUM +#define CFG_TUH_CDC_LINE_CODING_ON_ENUM_CH34X CFG_TUH_CDC_LINE_CODING_ON_ENUM +#else // this default is necessary to work properly +#define CFG_TUH_CDC_LINE_CODING_ON_ENUM_CH34X { 9600, CDC_LINE_CONDING_STOP_BITS_1, CDC_LINE_CODING_PARITY_NONE, 8 } +#endif + +// USB requests +#define CH34X_REQ_READ_VERSION 0x5F // dec 95 +#define CH34X_REQ_WRITE_REG 0x9A // dec 154 +#define CH34X_REQ_READ_REG 0x95 // dec 149 +#define CH34X_REQ_SERIAL_INIT 0xA1 // dec 161 +#define CH34X_REQ_MODEM_CTRL 0xA4 // dev 164 + +// registers +#define CH34X_REG_BREAK 0x05 +#define CH34X_REG_PRESCALER 0x12 +#define CH34X_REG_DIVISOR 0x13 +#define CH34X_REG_LCR 0x18 +#define CH34X_REG_LCR2 0x25 +#define CH34X_REG_MCR_MSR 0x06 +#define CH34X_REG_MCR_MSR2 0x07 +#define CH34X_NBREAK_BITS 0x01 + +#define CH341_REG_0x0F 0x0F // undocumented register +#define CH341_REG_0x2C 0x2C // undocumented register +#define CH341_REG_0x27 0x27 // hardware flow control (cts/rts) + +#define CH34X_REG16_DIVISOR_PRESCALER TU_U16(CH34X_REG_DIVISOR, CH34X_REG_PRESCALER) +#define CH32X_REG16_LCR2_LCR TU_U16(CH34X_REG_LCR2, CH34X_REG_LCR) + +// modem control bits +#define CH34X_BIT_RTS ( 1 << 6 ) +#define CH34X_BIT_DTR ( 1 << 5 ) + +// line control bits +#define CH34X_LCR_ENABLE_RX 0x80 +#define CH34X_LCR_ENABLE_TX 0x40 +#define CH34X_LCR_MARK_SPACE 0x20 +#define CH34X_LCR_PAR_EVEN 0x10 +#define CH34X_LCR_ENABLE_PAR 0x08 +#define CH34X_LCR_PAR_MASK 0x38 // all parity bits +#define CH34X_LCR_STOP_BITS_2 0x04 +#define CH34X_LCR_CS8 0x03 +#define CH34X_LCR_CS7 0x02 +#define CH34X_LCR_CS6 0x01 +#define CH34X_LCR_CS5 0x00 +#define CH34X_LCR_CS_MASK 0x03 // all CSx bits + +#endif /* _CH34X_H_ */ diff --git a/src/class/hid/hid_host.c b/src/class/hid/hid_host.c index db52b503f..709fa3dd8 100644 --- a/src/class/hid/hid_host.c +++ b/src/class/hid/hid_host.c @@ -50,6 +50,7 @@ typedef struct uint8_t itf_num; uint8_t ep_in; uint8_t ep_out; + bool mounted; // Enumeration is complete uint8_t itf_protocol; // None, Keyboard, Mouse uint8_t protocol_mode; // Boot (0) or Report protocol (1) @@ -139,7 +140,8 @@ uint8_t tuh_hid_itf_get_total_count(void) bool tuh_hid_mounted(uint8_t daddr, uint8_t idx) { hidh_interface_t* p_hid = get_hid_itf(daddr, idx); - return p_hid != NULL; + TU_VERIFY(p_hid); + return p_hid->mounted; } bool tuh_hid_itf_get_info(uint8_t daddr, uint8_t idx, tuh_itf_info_t* info) @@ -463,6 +465,7 @@ void hidh_close(uint8_t daddr) TU_LOG_DRV(" HIDh close addr = %u index = %u\r\n", daddr, i); if(tuh_hid_umount_cb) tuh_hid_umount_cb(daddr, i); p_hid->daddr = 0; + p_hid->mounted = false; } } } @@ -632,6 +635,7 @@ static void config_driver_mount_complete(uint8_t daddr, uint8_t idx, uint8_t con { hidh_interface_t* p_hid = get_hid_itf(daddr, idx); TU_VERIFY(p_hid, ); + p_hid->mounted = true; // enumeration is complete if (tuh_hid_mount_cb) tuh_hid_mount_cb(daddr, idx, desc_report, desc_len); diff --git a/src/class/vendor/vendor_device.c b/src/class/vendor/vendor_device.c index 389a29696..a68cb2156 100644 --- a/src/class/vendor/vendor_device.c +++ b/src/class/vendor/vendor_device.c @@ -49,10 +49,8 @@ typedef struct uint8_t rx_ff_buf[CFG_TUD_VENDOR_RX_BUFSIZE]; uint8_t tx_ff_buf[CFG_TUD_VENDOR_TX_BUFSIZE]; -#if CFG_FIFO_MUTEX - osal_mutex_def_t rx_ff_mutex; - osal_mutex_def_t tx_ff_mutex; -#endif + OSAL_MUTEX_DEF(rx_ff_mutex); + OSAL_MUTEX_DEF(tx_ff_mutex); // Endpoint Transfer buffer CFG_TUSB_MEM_ALIGN uint8_t epout_buf[CFG_TUD_VENDOR_EPSIZE]; @@ -183,10 +181,8 @@ void vendord_init(void) tu_fifo_config(&p_itf->rx_ff, p_itf->rx_ff_buf, CFG_TUD_VENDOR_RX_BUFSIZE, 1, false); tu_fifo_config(&p_itf->tx_ff, p_itf->tx_ff_buf, CFG_TUD_VENDOR_TX_BUFSIZE, 1, false); -#if CFG_FIFO_MUTEX tu_fifo_config_mutex(&p_itf->rx_ff, NULL, osal_mutex_create(&p_itf->rx_ff_mutex)); tu_fifo_config_mutex(&p_itf->tx_ff, osal_mutex_create(&p_itf->tx_ff_mutex), NULL); -#endif } } diff --git a/src/class/video/video.h b/src/class/video/video.h index d9880c291..6319c6536 100644 --- a/src/class/video/video.h +++ b/src/class/video/video.h @@ -29,6 +29,10 @@ #include "common/tusb_common.h" +enum { + VIDEO_BCD_1_50 = 0x0150, +}; + // Table 3-19 Color Matching Descriptor typedef enum { VIDEO_COLOR_PRIMARIES_UNDEFINED = 0x00, @@ -198,55 +202,98 @@ typedef enum { } video_terminal_type_t; //--------------------------------------------------------------------+ -// Descriptors +// Video Control (VC) Descriptors //--------------------------------------------------------------------+ /* 2.3.4.2 */ +#define tusb_desc_video_control_header_nitf_t(_nitf) \ + struct TU_ATTR_PACKED { \ + uint8_t bLength; \ + uint8_t bDescriptorType; \ + uint8_t bDescriptorSubType; \ + uint16_t bcdUVC; \ + uint16_t wTotalLength; \ + uint32_t dwClockFrequency; /* deprecated */ \ + uint8_t bInCollection; \ + uint8_t baInterfaceNr[_nitf]; \ + } + +typedef tusb_desc_video_control_header_nitf_t() tusb_desc_video_control_header_t; +typedef tusb_desc_video_control_header_nitf_t(1) tusb_desc_video_control_header_1itf_t; +typedef tusb_desc_video_control_header_nitf_t(2) tusb_desc_video_control_header_2itf_t; +typedef tusb_desc_video_control_header_nitf_t(3) tusb_desc_video_control_header_3itf_t; +typedef tusb_desc_video_control_header_nitf_t(4) tusb_desc_video_control_header_4itf_t; + typedef struct TU_ATTR_PACKED { uint8_t bLength; uint8_t bDescriptorType; uint8_t bDescriptorSubType; - uint16_t bcdUVC; - uint16_t wTotalLength; - uint32_t dwClockFrequency; - uint8_t bInCollection; - uint8_t baInterfaceNr[]; -} tusb_desc_cs_video_ctl_itf_hdr_t; + uint8_t bTerminalID; + uint16_t wTerminalType; + uint8_t bAssocTerminal; + uint8_t iTerminal; +} tusb_desc_video_control_input_terminal_t; + +TU_VERIFY_STATIC(sizeof(tusb_desc_video_control_input_terminal_t) == 8, "size is not correct"); -/* 2.4.3.3 */ typedef struct TU_ATTR_PACKED { - uint8_t bHeaderLength; - union { - uint8_t bmHeaderInfo; - struct { - uint8_t FrameID: 1; - uint8_t EndOfFrame: 1; - uint8_t PresentationTime: 1; - uint8_t SourceClockReference: 1; - uint8_t PayloadSpecific: 1; - uint8_t StillImage: 1; - uint8_t Error: 1; - uint8_t EndOfHeader: 1; - }; - }; -} tusb_video_payload_header_t; + uint8_t bLength; + uint8_t bDescriptorType; + uint8_t bDescriptorSubType; + uint8_t bTerminalID; + uint16_t wTerminalType; + uint8_t bAssocTerminal; + uint8_t bSourceID; + uint8_t iTerminal; +} tusb_desc_video_control_output_terminal_t; + +TU_VERIFY_STATIC(sizeof(tusb_desc_video_control_output_terminal_t) == 9, "size is not correct"); -/* 3.9.2.1 */ typedef struct TU_ATTR_PACKED { uint8_t bLength; uint8_t bDescriptorType; uint8_t bDescriptorSubType; - uint8_t bNumFormats; - uint16_t wTotalLength; - uint8_t bEndpointAddress; - uint8_t bmInfo; - uint8_t bTerminalLink; - uint8_t bStillCaptureMethod; - uint8_t bTriggerSupport; - uint8_t bTriggerUsage; + uint8_t bTerminalID; + uint16_t wTerminalType; + uint8_t bAssocTerminal; + uint8_t iTerminal; + + uint16_t wObjectiveFocalLengthMin; + uint16_t wObjectiveFocalLengthMax; + uint16_t wOcularFocalLength; uint8_t bControlSize; - uint8_t bmaControls[]; -} tusb_desc_cs_video_stm_itf_in_hdr_t; + uint8_t bmControls[3]; +} tusb_desc_video_control_camera_terminal_t; + +TU_VERIFY_STATIC(sizeof(tusb_desc_video_control_camera_terminal_t) == 18, "size is not correct"); + +//--------------------------------------------------------------------+ +// Video Streaming (VS) Descriptors +//--------------------------------------------------------------------+ + +/* 3.9.2.1 */ +#define tusb_desc_video_streaming_input_header_nbyte_t(_nb) \ + struct TU_ATTR_PACKED { \ + uint8_t bLength; \ + uint8_t bDescriptorType; \ + uint8_t bDescriptorSubType; \ + uint8_t bNumFormats; /* Number of video payload Format descriptors for this interface */ \ + uint16_t wTotalLength; \ + uint8_t bEndpointAddress; \ + uint8_t bmInfo; /* Bit 0: dynamic format change supported */ \ + uint8_t bTerminalLink; \ + uint8_t bStillCaptureMethod; \ + uint8_t bTriggerSupport; /* Hardware trigger supported */ \ + uint8_t bTriggerUsage; \ + uint8_t bControlSize; /* sizeof of each control item */ \ + uint8_t bmaControls[_nb]; \ + } + +typedef tusb_desc_video_streaming_input_header_nbyte_t() tusb_desc_video_streaming_input_header_t; +typedef tusb_desc_video_streaming_input_header_nbyte_t(1) tusb_desc_video_streaming_input_header_1byte_t; +typedef tusb_desc_video_streaming_input_header_nbyte_t(2) tusb_desc_video_streaming_input_header_2byte_t; +typedef tusb_desc_video_streaming_input_header_nbyte_t(3) tusb_desc_video_streaming_input_header_3byte_t; +typedef tusb_desc_video_streaming_input_header_nbyte_t(4) tusb_desc_video_streaming_input_header_4byte_t; /* 3.9.2.2 */ typedef struct TU_ATTR_PACKED { @@ -259,7 +306,7 @@ typedef struct TU_ATTR_PACKED { uint8_t bTerminalLink; uint8_t bControlSize; uint8_t bmaControls[]; -} tusb_desc_cs_video_stm_itf_out_hdr_t; +} tusb_desc_video_streaming_output_header_t; typedef struct TU_ATTR_PACKED { uint8_t bLength; @@ -285,14 +332,33 @@ typedef struct TU_ATTR_PACKED { uint8_t bmaControls[]; } output; }; -} tusb_desc_cs_video_stm_itf_hdr_t; +} tusb_desc_video_streaming_inout_header_t; + +// 3.9.2.6 Color Matching Descriptor +typedef struct TU_ATTR_PACKED { + uint8_t bLength; + uint8_t bDescriptorType; + uint8_t bDescriptorSubType; + uint8_t bColorPrimaries; + uint8_t bTransferCharacteristics; + uint8_t bMatrixCoefficients; +} tusb_desc_video_streaming_color_matching_t; +TU_VERIFY_STATIC(sizeof(tusb_desc_video_streaming_color_matching_t) == 6, "size is not correct"); + +//--------------------------------------------------------------------+ +// Format and Frame Descriptor +// Note: bFormatIndex & bFrameIndex are 1-based index +//--------------------------------------------------------------------+ + +//------------- Uncompressed -------------// +// Uncompressed payload specs: 3.1.1 format descriptor typedef struct TU_ATTR_PACKED { uint8_t bLength; uint8_t bDescriptorType; uint8_t bDescriptorSubType; uint8_t bFormatIndex; - uint8_t bNumFrameDescriptors; + uint8_t bNumFrameDescriptors; // Number of frame descriptors for this format uint8_t guidFormat[16]; uint8_t bBitsPerPixel; uint8_t bDefaultFrameIndex; @@ -300,22 +366,65 @@ typedef struct TU_ATTR_PACKED { uint8_t bAspectRatioY; uint8_t bmInterlaceFlags; uint8_t bCopyProtect; -} tusb_desc_cs_video_fmt_uncompressed_t; - +} tusb_desc_video_format_uncompressed_t; + +// Uncompressed payload specs: 3.1.2 frame descriptor +#define tusb_desc_video_frame_uncompressed_nint_t(_nint) \ + struct TU_ATTR_PACKED { \ + uint8_t bLength; \ + uint8_t bDescriptorType; \ + uint8_t bDescriptorSubType; \ + uint8_t bFrameIndex; \ + uint8_t bmCapabilities; \ + uint16_t wWidth; \ + uint16_t wHeight; \ + uint32_t dwMinBitRate; \ + uint32_t dwMaxBitRate; \ + uint32_t dwMaxVideoFrameBufferSize; /* deprecated in 1.5 */ \ + uint32_t dwDefaultFrameInterval; \ + uint8_t bFrameIntervalType; \ + uint32_t dwFrameInterval[_nint]; \ + } + +typedef tusb_desc_video_frame_uncompressed_nint_t() tusb_desc_video_frame_uncompressed_t; +typedef tusb_desc_video_frame_uncompressed_nint_t(1) tusb_desc_video_frame_uncompressed_1int_t; +typedef tusb_desc_video_frame_uncompressed_nint_t(2) tusb_desc_video_frame_uncompressed_2int_t; +typedef tusb_desc_video_frame_uncompressed_nint_t(3) tusb_desc_video_frame_uncompressed_3int_t; +typedef tusb_desc_video_frame_uncompressed_nint_t(4) tusb_desc_video_frame_uncompressed_4int_t; + +// continuous = 3 intervals: min, max, step +typedef tusb_desc_video_frame_uncompressed_3int_t tusb_desc_video_frame_uncompressed_continuous_t; + +TU_VERIFY_STATIC(sizeof(tusb_desc_video_frame_uncompressed_continuous_t) == 38, "size is not correct"); + +//------------- MJPEG -------------// +// MJPEG payload specs: 3.1.1 format descriptor typedef struct TU_ATTR_PACKED { uint8_t bLength; uint8_t bDescriptorType; uint8_t bDescriptorSubType; uint8_t bFormatIndex; uint8_t bNumFrameDescriptors; - uint8_t bmFlags; + uint8_t bmFlags; // Bit 0: fixed size samples (1 = yes) uint8_t bDefaultFrameIndex; uint8_t bAspectRatioX; uint8_t bAspectRatioY; uint8_t bmInterlaceFlags; uint8_t bCopyProtect; -} tusb_desc_cs_video_fmt_mjpeg_t; +} tusb_desc_video_format_mjpeg_t; +// MJPEG payload specs: 3.1.2 frame descriptor (same as uncompressed) +typedef tusb_desc_video_frame_uncompressed_t tusb_desc_video_frame_mjpeg_t; +typedef tusb_desc_video_frame_uncompressed_1int_t tusb_desc_video_frame_mjpeg_1int_t; +typedef tusb_desc_video_frame_uncompressed_2int_t tusb_desc_video_frame_mjpeg_2int_t; +typedef tusb_desc_video_frame_uncompressed_3int_t tusb_desc_video_frame_mjpeg_3int_t; +typedef tusb_desc_video_frame_uncompressed_4int_t tusb_desc_video_frame_mjpeg_4int_t; + +// continuous = 3 intervals: min, max, step +typedef tusb_desc_video_frame_mjpeg_3int_t tusb_desc_video_frame_mjpeg_continuous_t; + +//------------- DV -------------// +// DV payload specs: 3.1.1 typedef struct TU_ATTR_PACKED { uint8_t bLength; uint8_t bDescriptorType; @@ -323,8 +432,9 @@ typedef struct TU_ATTR_PACKED { uint8_t bFormatIndex; uint32_t dwMaxVideoFrameBufferSize; /* deprecated */ uint8_t bFormatType; -} tusb_desc_cs_video_fmt_dv_t; +} tusb_desc_video_format_dv_t; +// Frame Based payload specs: 3.1.1 typedef struct TU_ATTR_PACKED { uint8_t bLength; uint8_t bDescriptorType; @@ -339,25 +449,7 @@ typedef struct TU_ATTR_PACKED { uint8_t bmInterlaceFlags; uint8_t bCopyProtect; uint8_t bVaribaleSize; -} tusb_desc_cs_video_fmt_frame_based_t; - -typedef struct TU_ATTR_PACKED { - uint8_t bLength; - uint8_t bDescriptorType; - uint8_t bDescriptorSubType; - uint8_t bFrameIndex; - uint8_t bmCapabilities; - uint16_t wWidth; - uint16_t wHeight; - uint32_t dwMinBitRate; - uint32_t dwMaxBitRate; - uint32_t dwMaxVideoFrameBufferSize; /* deprecated */ - uint32_t dwDefaultFrameInterval; - uint8_t bFrameIntervalType; - uint32_t dwFrameInterval[]; -} tusb_desc_cs_video_frm_uncompressed_t; - -typedef tusb_desc_cs_video_frm_uncompressed_t tusb_desc_cs_video_frm_mjpeg_t; +} tusb_desc_video_format_framebased_t; typedef struct TU_ATTR_PACKED { uint8_t bLength; @@ -373,12 +465,30 @@ typedef struct TU_ATTR_PACKED { uint8_t bFrameIntervalType; uint32_t dwBytesPerLine; uint32_t dwFrameInterval[]; -} tusb_desc_cs_video_frm_frame_based_t; +} tusb_desc_video_frame_framebased_t; //--------------------------------------------------------------------+ // Requests //--------------------------------------------------------------------+ +/* 2.4.3.3 */ +typedef struct TU_ATTR_PACKED { + uint8_t bHeaderLength; + union { + uint8_t bmHeaderInfo; + struct { + uint8_t FrameID: 1; + uint8_t EndOfFrame: 1; + uint8_t PresentationTime: 1; + uint8_t SourceClockReference: 1; + uint8_t PayloadSpecific: 1; + uint8_t StillImage: 1; + uint8_t Error: 1; + uint8_t EndOfHeader: 1; + }; + }; +} tusb_video_payload_header_t; + /* 4.3.1.1 */ typedef struct TU_ATTR_PACKED { union { @@ -537,7 +647,7 @@ TU_VERIFY_STATIC( sizeof(video_probe_and_commit_control_t) == 48, "size is not c /* Motion-JPEG 3.1.1 Table 3-2 and 3-4 */ #define TUD_VIDEO_DESC_CS_VS_FRM_MJPEG_DISC(_frmidx, _cap, _width, _height, _minbr, _maxbr, _maxfrmbufsz, _frminterval, ...) \ TUD_VIDEO_DESC_CS_VS_FRM_MJPEG_DISC_LEN + (TU_ARGS_NUM(__VA_ARGS__)) * 4, \ - TUSB_DESC_CS_INTERFACE, VIDEO_CS_VS_INTERFACE_FRAME_MJPEG, \ + TUSB_DESC_CS_INTERFACE, VIDEO_CS_ITF_VS_FRAME_MJPEG, \ _frmidx, _cap, U16_TO_U8S_LE(_width), U16_TO_U8S_LE(_height), U32_TO_U8S_LE(_minbr), U32_TO_U8S_LE(_maxbr), \ U32_TO_U8S_LE(_maxfrmbufsz), U32_TO_U8S_LE(_frminterval), (TU_ARGS_NUM(__VA_ARGS__)), __VA_ARGS__ diff --git a/src/class/video/video_device.c b/src/class/video/video_device.c index 3b29454a3..1affd615e 100644 --- a/src/class/video/video_device.c +++ b/src/class/video/video_device.c @@ -50,17 +50,17 @@ typedef struct { tusb_desc_interface_t std; - tusb_desc_cs_video_ctl_itf_hdr_t ctl; + tusb_desc_video_control_header_t ctl; } tusb_desc_vc_itf_t; typedef struct { tusb_desc_interface_t std; - tusb_desc_cs_video_stm_itf_hdr_t stm; + tusb_desc_video_streaming_inout_header_t stm; } tusb_desc_vs_itf_t; typedef union { - tusb_desc_cs_video_ctl_itf_hdr_t ctl; - tusb_desc_cs_video_stm_itf_hdr_t stm; + tusb_desc_video_control_header_t ctl; + tusb_desc_video_streaming_inout_header_t stm; } tusb_desc_video_itf_hdr_t; typedef struct TU_ATTR_PACKED { @@ -78,9 +78,9 @@ typedef union { uint8_t bFormatIndex; uint8_t bNumFrameDescriptors; }; - tusb_desc_cs_video_fmt_uncompressed_t uncompressed; - tusb_desc_cs_video_fmt_mjpeg_t mjpeg; - tusb_desc_cs_video_fmt_frame_based_t frame_based; + tusb_desc_video_format_uncompressed_t uncompressed; + tusb_desc_video_format_mjpeg_t mjpeg; + tusb_desc_video_format_framebased_t frame_based; } tusb_desc_cs_video_fmt_t; typedef union { @@ -93,9 +93,9 @@ typedef union { uint16_t wWidth; uint16_t wHeight; }; - tusb_desc_cs_video_frm_uncompressed_t uncompressed; - tusb_desc_cs_video_frm_mjpeg_t mjpeg; - tusb_desc_cs_video_frm_frame_based_t frame_based; + tusb_desc_video_frame_uncompressed_t uncompressed; + tusb_desc_video_frame_mjpeg_t mjpeg; + tusb_desc_video_frame_framebased_t frame_based; } tusb_desc_cs_video_frm_t; /* video streaming interface */ @@ -434,8 +434,9 @@ static bool _update_streaming_parameters(videod_streaming_interface_t const *stm uint_fast32_t interval_ms = interval / 10000; TU_ASSERT(interval_ms); uint_fast32_t payload_size = (frame_size + interval_ms - 1) / interval_ms + 2; - if (CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE < payload_size) + if (CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE < payload_size) { payload_size = CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE; + } param->dwMaxPayloadTransferSize = payload_size; return true; } @@ -577,8 +578,9 @@ static bool _negotiate_streaming_parameters(videod_streaming_interface_t const * } else { payload_size = (frame_size + interval_ms - 1) / interval_ms + 2; } - if (CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE < payload_size) + if (CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE < payload_size) { payload_size = CFG_TUD_VIDEO_STREAMING_EP_BUFSIZE; + } param->dwMaxPayloadTransferSize = payload_size; } return true; diff --git a/src/common/tusb_common.h b/src/common/tusb_common.h index caeb5f2ef..1f08ce4ed 100644 --- a/src/common/tusb_common.h +++ b/src/common/tusb_common.h @@ -37,6 +37,7 @@ #define TU_ARRAY_SIZE(_arr) ( sizeof(_arr) / sizeof(_arr[0]) ) #define TU_MIN(_x, _y) ( ( (_x) < (_y) ) ? (_x) : (_y) ) #define TU_MAX(_x, _y) ( ( (_x) > (_y) ) ? (_x) : (_y) ) +#define TU_DIV_CEIL(n, d) (((n) + (d) - 1) / (d)) #define TU_U16(_high, _low) ((uint16_t) (((_high) << 8) | (_low))) #define TU_U16_HIGH(_u16) ((uint8_t) (((_u16) >> 8) & 0x00ff)) diff --git a/src/common/tusb_types.h b/src/common/tusb_types.h index fab680989..2c5dce723 100644 --- a/src/common/tusb_types.h +++ b/src/common/tusb_types.h @@ -44,43 +44,38 @@ *------------------------------------------------------------------*/ /// defined base on EHCI specs value for Endpoint Speed -typedef enum -{ +typedef enum { TUSB_SPEED_FULL = 0, TUSB_SPEED_LOW = 1, TUSB_SPEED_HIGH = 2, TUSB_SPEED_INVALID = 0xff, -}tusb_speed_t; +} tusb_speed_t; /// defined base on USB Specs Endpoint's bmAttributes -typedef enum -{ +typedef enum { TUSB_XFER_CONTROL = 0 , TUSB_XFER_ISOCHRONOUS , TUSB_XFER_BULK , TUSB_XFER_INTERRUPT -}tusb_xfer_type_t; +} tusb_xfer_type_t; -typedef enum -{ +typedef enum { TUSB_DIR_OUT = 0, TUSB_DIR_IN = 1, TUSB_DIR_IN_MASK = 0x80 -}tusb_dir_t; +} tusb_dir_t; -enum -{ +enum { TUSB_EPSIZE_BULK_FS = 64, - TUSB_EPSIZE_BULK_HS= 512, + TUSB_EPSIZE_BULK_HS = 512, TUSB_EPSIZE_ISO_FS_MAX = 1023, TUSB_EPSIZE_ISO_HS_MAX = 1024, }; -/// Isochronous End Point Attributes -typedef enum -{ +/// Isochronous Endpoint Attributes +typedef enum { TUSB_ISO_EP_ATT_NO_SYNC = 0x00, TUSB_ISO_EP_ATT_ASYNCHRONOUS = 0x04, TUSB_ISO_EP_ATT_ADAPTIVE = 0x08, @@ -88,11 +83,10 @@ typedef enum TUSB_ISO_EP_ATT_DATA = 0x00, ///< Data End Point TUSB_ISO_EP_ATT_EXPLICIT_FB = 0x10, ///< Feedback End Point TUSB_ISO_EP_ATT_IMPLICIT_FB = 0x20, ///< Data endpoint that also serves as an implicit feedback -}tusb_iso_ep_attribute_t; +} tusb_iso_ep_attribute_t; /// USB Descriptor Types -typedef enum -{ +typedef enum { TUSB_DESC_DEVICE = 0x01, TUSB_DESC_CONFIGURATION = 0x02, TUSB_DESC_STRING = 0x03, @@ -119,10 +113,9 @@ typedef enum TUSB_DESC_SUPERSPEED_ENDPOINT_COMPANION = 0x30, TUSB_DESC_SUPERSPEED_ISO_ENDPOINT_COMPANION = 0x31 -}tusb_desc_type_t; +} tusb_desc_type_t; -typedef enum -{ +typedef enum { TUSB_REQ_GET_STATUS = 0 , TUSB_REQ_CLEAR_FEATURE = 1 , TUSB_REQ_RESERVED = 2 , @@ -136,25 +129,22 @@ typedef enum TUSB_REQ_GET_INTERFACE = 10 , TUSB_REQ_SET_INTERFACE = 11 , TUSB_REQ_SYNCH_FRAME = 12 -}tusb_request_code_t; +} tusb_request_code_t; -typedef enum -{ +typedef enum { TUSB_REQ_FEATURE_EDPT_HALT = 0, TUSB_REQ_FEATURE_REMOTE_WAKEUP = 1, TUSB_REQ_FEATURE_TEST_MODE = 2 -}tusb_request_feature_selector_t; +} tusb_request_feature_selector_t; -typedef enum -{ +typedef enum { TUSB_REQ_TYPE_STANDARD = 0, TUSB_REQ_TYPE_CLASS, TUSB_REQ_TYPE_VENDOR, TUSB_REQ_TYPE_INVALID } tusb_request_type_t; -typedef enum -{ +typedef enum { TUSB_REQ_RCPT_DEVICE =0, TUSB_REQ_RCPT_INTERFACE, TUSB_REQ_RCPT_ENDPOINT, @@ -162,8 +152,7 @@ typedef enum } tusb_request_recipient_t; // https://www.usb.org/defined-class-codes -typedef enum -{ +typedef enum { TUSB_CLASS_UNSPECIFIED = 0 , TUSB_CLASS_AUDIO = 1 , TUSB_CLASS_CDC = 2 , @@ -187,26 +176,23 @@ typedef enum TUSB_CLASS_MISC = 0xEF , TUSB_CLASS_APPLICATION_SPECIFIC = 0xFE , TUSB_CLASS_VENDOR_SPECIFIC = 0xFF -}tusb_class_code_t; +} tusb_class_code_t; typedef enum { MISC_SUBCLASS_COMMON = 2 }misc_subclass_type_t; -typedef enum -{ +typedef enum { MISC_PROTOCOL_IAD = 1 -}misc_protocol_type_t; +} misc_protocol_type_t; -typedef enum -{ +typedef enum { APP_SUBCLASS_USBTMC = 0x03, APP_SUBCLASS_DFU_RUNTIME = 0x01 } app_subclass_type_t; -typedef enum -{ +typedef enum { DEVICE_CAPABILITY_WIRELESS_USB = 0x01, DEVICE_CAPABILITY_USB20_EXTENSION = 0x02, DEVICE_CAPABILITY_SUPERSPEED_USB = 0x03, @@ -223,7 +209,7 @@ typedef enum DEVICE_CAPABILITY_AUTHENTICATION = 0x0E, DEVICE_CAPABILITY_BILLBOARD_EX = 0x0F, DEVICE_CAPABILITY_CONFIGURATION_SUMMARY = 0x10 -}device_capability_type_t; +} device_capability_type_t; enum { TUSB_DESC_CONFIG_ATT_REMOTE_WAKEUP = TU_BIT(5), @@ -235,28 +221,25 @@ enum { //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ -typedef enum -{ +typedef enum { XFER_RESULT_SUCCESS = 0, XFER_RESULT_FAILED, XFER_RESULT_STALLED, XFER_RESULT_TIMEOUT, XFER_RESULT_INVALID -}xfer_result_t; +} xfer_result_t; -enum // TODO remove -{ +// TODO remove +enum { DESC_OFFSET_LEN = 0, DESC_OFFSET_TYPE = 1 }; -enum -{ +enum { INTERFACE_INVALID_NUMBER = 0xff }; -typedef enum -{ +typedef enum { MS_OS_20_SET_HEADER_DESCRIPTOR = 0x00, MS_OS_20_SUBSET_HEADER_CONFIGURATION = 0x01, MS_OS_20_SUBSET_HEADER_FUNCTION = 0x02, @@ -268,16 +251,14 @@ typedef enum MS_OS_20_FEATURE_VENDOR_REVISION = 0x08 } microsoft_os_20_type_t; -enum -{ +enum { CONTROL_STAGE_IDLE, CONTROL_STAGE_SETUP, CONTROL_STAGE_DATA, CONTROL_STAGE_ACK }; -enum -{ +enum { TUSB_INDEX_INVALID_8 = 0xFFu }; @@ -290,8 +271,7 @@ TU_ATTR_PACKED_BEGIN TU_ATTR_BIT_FIELD_ORDER_BEGIN /// USB Device Descriptor -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength ; ///< Size of this descriptor in bytes. uint8_t bDescriptorType ; ///< DEVICE Descriptor Type. uint16_t bcdUSB ; ///< BUSB Specification Release Number in Binary-Coded Decimal (i.e., 2.10 is 210H). This field identifies the release of the USB Specification with which the device and its descriptors are compliant. @@ -314,8 +294,7 @@ typedef struct TU_ATTR_PACKED TU_VERIFY_STATIC( sizeof(tusb_desc_device_t) == 18, "size is not correct"); // USB Binary Device Object Store (BOS) Descriptor -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength ; ///< Size of this descriptor in bytes uint8_t bDescriptorType ; ///< CONFIGURATION Descriptor Type uint16_t wTotalLength ; ///< Total length of data returned for this descriptor @@ -325,8 +304,7 @@ typedef struct TU_ATTR_PACKED TU_VERIFY_STATIC( sizeof(tusb_desc_bos_t) == 5, "size is not correct"); /// USB Configuration Descriptor -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength ; ///< Size of this descriptor in bytes uint8_t bDescriptorType ; ///< CONFIGURATION Descriptor Type uint16_t wTotalLength ; ///< Total length of data returned for this configuration. Includes the combined length of all descriptors (configuration, interface, endpoint, and class- or vendor-specific) returned for this configuration. @@ -341,8 +319,7 @@ typedef struct TU_ATTR_PACKED TU_VERIFY_STATIC( sizeof(tusb_desc_configuration_t) == 9, "size is not correct"); /// USB Interface Descriptor -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength ; ///< Size of this descriptor in bytes uint8_t bDescriptorType ; ///< INTERFACE Descriptor Type @@ -358,8 +335,7 @@ typedef struct TU_ATTR_PACKED TU_VERIFY_STATIC( sizeof(tusb_desc_interface_t) == 9, "size is not correct"); /// USB Endpoint Descriptor -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength ; // Size of this descriptor in bytes uint8_t bDescriptorType ; // ENDPOINT Descriptor Type @@ -379,8 +355,7 @@ typedef struct TU_ATTR_PACKED TU_VERIFY_STATIC( sizeof(tusb_desc_endpoint_t) == 7, "size is not correct"); /// USB Other Speed Configuration Descriptor -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength ; ///< Size of descriptor uint8_t bDescriptorType ; ///< Other_speed_Configuration Type uint16_t wTotalLength ; ///< Total length of data returned @@ -393,8 +368,7 @@ typedef struct TU_ATTR_PACKED } tusb_desc_other_speed_t; /// USB Device Qualifier Descriptor -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength ; ///< Size of descriptor uint8_t bDescriptorType ; ///< Device Qualifier Type uint16_t bcdUSB ; ///< USB specification version number (e.g., 0200H for V2.00) @@ -411,8 +385,7 @@ typedef struct TU_ATTR_PACKED TU_VERIFY_STATIC( sizeof(tusb_desc_device_qualifier_t) == 10, "size is not correct"); /// USB Interface Association Descriptor (IAD ECN) -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength ; ///< Size of descriptor uint8_t bDescriptorType ; ///< Other_speed_Configuration Type @@ -426,17 +399,17 @@ typedef struct TU_ATTR_PACKED uint8_t iFunction ; ///< Index of the string descriptor describing the interface association. } tusb_desc_interface_assoc_t; +TU_VERIFY_STATIC( sizeof(tusb_desc_interface_assoc_t) == 8, "size is not correct"); + // USB String Descriptor -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength ; ///< Size of this descriptor in bytes uint8_t bDescriptorType ; ///< Descriptor Type uint16_t unicode_string[]; } tusb_desc_string_t; // USB Binary Device Object Store (BOS) -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength; uint8_t bDescriptorType ; uint8_t bDevCapabilityType; @@ -445,9 +418,8 @@ typedef struct TU_ATTR_PACKED uint8_t CapabilityData[]; } tusb_desc_bos_platform_t; -// USB WebuSB URL Descriptor -typedef struct TU_ATTR_PACKED -{ +// USB WebUSB URL Descriptor +typedef struct TU_ATTR_PACKED { uint8_t bLength; uint8_t bDescriptorType; uint8_t bScheme; @@ -455,8 +427,7 @@ typedef struct TU_ATTR_PACKED } tusb_desc_webusb_url_t; // DFU Functional Descriptor -typedef struct TU_ATTR_PACKED -{ +typedef struct TU_ATTR_PACKED { uint8_t bLength; uint8_t bDescriptorType; @@ -481,7 +452,7 @@ typedef struct TU_ATTR_PACKED // //--------------------------------------------------------------------+ -typedef struct TU_ATTR_PACKED{ +typedef struct TU_ATTR_PACKED { union { struct TU_ATTR_PACKED { uint8_t recipient : 5; ///< Recipient type tusb_request_recipient_t. @@ -500,7 +471,6 @@ typedef struct TU_ATTR_PACKED{ TU_VERIFY_STATIC( sizeof(tusb_control_request_t) == 8, "size is not correct"); - TU_ATTR_PACKED_END // End of all packed definitions TU_ATTR_BIT_FIELD_ORDER_END @@ -509,36 +479,30 @@ TU_ATTR_BIT_FIELD_ORDER_END //--------------------------------------------------------------------+ // Get direction from Endpoint address -TU_ATTR_ALWAYS_INLINE static inline tusb_dir_t tu_edpt_dir(uint8_t addr) -{ +TU_ATTR_ALWAYS_INLINE static inline tusb_dir_t tu_edpt_dir(uint8_t addr) { return (addr & TUSB_DIR_IN_MASK) ? TUSB_DIR_IN : TUSB_DIR_OUT; } // Get Endpoint number from address -TU_ATTR_ALWAYS_INLINE static inline uint8_t tu_edpt_number(uint8_t addr) -{ +TU_ATTR_ALWAYS_INLINE static inline uint8_t tu_edpt_number(uint8_t addr) { return (uint8_t)(addr & (~TUSB_DIR_IN_MASK)); } -TU_ATTR_ALWAYS_INLINE static inline uint8_t tu_edpt_addr(uint8_t num, uint8_t dir) -{ +TU_ATTR_ALWAYS_INLINE static inline uint8_t tu_edpt_addr(uint8_t num, uint8_t dir) { return (uint8_t)(num | (dir ? TUSB_DIR_IN_MASK : 0)); } -TU_ATTR_ALWAYS_INLINE static inline uint16_t tu_edpt_packet_size(tusb_desc_endpoint_t const* desc_ep) -{ +TU_ATTR_ALWAYS_INLINE static inline uint16_t tu_edpt_packet_size(tusb_desc_endpoint_t const* desc_ep) { return tu_le16toh(desc_ep->wMaxPacketSize) & TU_GENMASK(10, 0); } #if CFG_TUSB_DEBUG -TU_ATTR_ALWAYS_INLINE static inline const char *tu_edpt_dir_str(tusb_dir_t dir) -{ +TU_ATTR_ALWAYS_INLINE static inline const char *tu_edpt_dir_str(tusb_dir_t dir) { tu_static const char *str[] = {"out", "in"}; return str[dir]; } -TU_ATTR_ALWAYS_INLINE static inline const char *tu_edpt_type_str(tusb_xfer_type_t t) -{ +TU_ATTR_ALWAYS_INLINE static inline const char *tu_edpt_type_str(tusb_xfer_type_t t) { tu_static const char *str[] = {"control", "isochronous", "bulk", "interrupt"}; return str[t]; } @@ -549,21 +513,18 @@ TU_ATTR_ALWAYS_INLINE static inline const char *tu_edpt_type_str(tusb_xfer_type_ //--------------------------------------------------------------------+ // return next descriptor -TU_ATTR_ALWAYS_INLINE static inline uint8_t const * tu_desc_next(void const* desc) -{ +TU_ATTR_ALWAYS_INLINE static inline uint8_t const * tu_desc_next(void const* desc) { uint8_t const* desc8 = (uint8_t const*) desc; return desc8 + desc8[DESC_OFFSET_LEN]; } // get descriptor type -TU_ATTR_ALWAYS_INLINE static inline uint8_t tu_desc_type(void const* desc) -{ +TU_ATTR_ALWAYS_INLINE static inline uint8_t tu_desc_type(void const* desc) { return ((uint8_t const*) desc)[DESC_OFFSET_TYPE]; } // get descriptor length -TU_ATTR_ALWAYS_INLINE static inline uint8_t tu_desc_len(void const* desc) -{ +TU_ATTR_ALWAYS_INLINE static inline uint8_t tu_desc_len(void const* desc) { return ((uint8_t const*) desc)[DESC_OFFSET_LEN]; } diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index ac93632be..3e15d51c6 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -1130,8 +1130,8 @@ void dcd_int_handler(uint8_t rhport) { dwc2->gotgint = otg_int; } - if (int_status & GINTSTS_SOF) { - dwc2->gotgint = GINTSTS_SOF; + if(int_status & GINTSTS_SOF) { + dwc2->gintsts = GINTSTS_SOF; if (_sof_en) { uint32_t frame = (dwc2->dsts & (DSTS_FNSOF)) >> 8; diff --git a/src/tusb_option.h b/src/tusb_option.h index 57f026312..767323bdd 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -472,6 +472,23 @@ {0x10C4, 0xEA60}, {0x10C4, 0xEA70} #endif +#ifndef CFG_TUH_CDC_CH34X + // CH34X is not part of CDC class, only to re-use CDC driver API + #define CFG_TUH_CDC_CH34X 0 +#endif + +#ifndef CFG_TUH_CDC_CH34X_VID_PID_LIST + // List of product IDs that can use the CH34X CDC driver + #define CFG_TUH_CDC_CH34X_VID_PID_LIST \ + { 0x1a86, 0x5523 }, /* ch341 chip */ \ + { 0x1a86, 0x7522 }, /* ch340k chip */ \ + { 0x1a86, 0x7523 }, /* ch340 chip */ \ + { 0x1a86, 0xe523 }, /* ch330 chip */ \ + { 0x4348, 0x5523 }, /* ch340 custom chip */ \ + { 0x2184, 0x0057 }, /* overtaken from Linux Kernel driver /drivers/usb/serial/ch341.c */ \ + { 0x9986, 0x7523 } /* overtaken from Linux Kernel driver /drivers/usb/serial/ch341.c */ +#endif + #ifndef CFG_TUH_HID #define CFG_TUH_HID 0 #endif diff --git a/test/hil/hil_test.py b/test/hil/hil_test.py index 7c662aeea..7f03ce43f 100644 --- a/test/hil/hil_test.py +++ b/test/hil/hil_test.py @@ -364,8 +364,15 @@ def main(config_file, board): print(f' {test} ...', end='') - # flash firmware - ret = globals()[f'flash_{flasher}'](item, fw) + # flash firmware. It may fail randomly, retry a few times + for i in range(3): + ret = globals()[f'flash_{flasher}'](item, fw) + if ret.returncode == 0: + break + else: + print(f'Flashing failed, retry {i+1}') + time.sleep(1) + assert ret.returncode == 0, 'Flash failed\n' + ret.stdout.decode() # run test -- cgit v1.3.1 From 45454c53f1d429a314115701ba2360591b811f50 Mon Sep 17 00:00:00 2001 From: Jerry Palacios Date: Wed, 7 Feb 2024 18:33:19 -0600 Subject: frdmmcxa153 files added --- hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h | 149 ++++++++ hw/bsp/mcxa/boards/frdmmcxa153/board.cmake | 18 + hw/bsp/mcxa/boards/frdmmcxa153/board.h | 66 ++++ hw/bsp/mcxa/boards/frdmmcxa153/board.mk | 26 ++ hw/bsp/mcxa/boards/frdmmcxa153/clock_config.c | 468 ++++++++++++++++++++++++++ hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h | 170 ++++++++++ hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c | 159 +++++++++ hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h | 47 +++ hw/bsp/mcxa/debug.jlinkscript | 5 + hw/bsp/mcxa/family.c | 163 +++++++++ hw/bsp/mcxa/family.cmake | 110 ++++++ hw/bsp/mcxa/family.mk | 42 +++ src/common/tusb_mcu.h | 7 + src/portable/chipidea/ci_fs/ci_fs_mcxa.h | 47 +++ src/portable/chipidea/ci_fs/dcd_ci_fs.c | 2 + src/tusb_option.h | 1 + 16 files changed, 1480 insertions(+) create mode 100644 hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h create mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/board.cmake create mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/board.h create mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/board.mk create mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/clock_config.c create mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h create mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c create mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h create mode 100644 hw/bsp/mcxa/debug.jlinkscript create mode 100644 hw/bsp/mcxa/family.c create mode 100644 hw/bsp/mcxa/family.cmake create mode 100644 hw/bsp/mcxa/family.mk create mode 100644 src/portable/chipidea/ci_fs/ci_fs_mcxa.h (limited to 'src/portable') diff --git a/hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h new file mode 100644 index 000000000..6f10a7ab0 --- /dev/null +++ b/hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h @@ -0,0 +1,149 @@ +/* + * FreeRTOS Kernel V10.0.0 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. If you wish to use our Amazon + * FreeRTOS name, please do so in a fair use way that does not cause confusion. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + + +#ifndef FREERTOS_CONFIG_H +#define FREERTOS_CONFIG_H + +/*----------------------------------------------------------- + * Application specific definitions. + * + * These definitions should be adjusted for your particular hardware and + * application requirements. + * + * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE + * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. + * + * See http://www.freertos.org/a00110.html. + *----------------------------------------------------------*/ + +// skip if included from IAR assembler +#ifndef __IASMARM__ + #include "fsl_device_registers.h" +#endif + +/* Cortex M23/M33 port configuration. */ +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) + +#define configUSE_PREEMPTION 1 +#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 +#define configCPU_CLOCK_HZ SystemCoreClock +#define configTICK_RATE_HZ ( 1000 ) +#define configMAX_PRIORITIES ( 5 ) +#define configMINIMAL_STACK_SIZE ( 128 ) +#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) +#define configMAX_TASK_NAME_LEN 16 +#define configUSE_16_BIT_TICKS 0 +#define configIDLE_SHOULD_YIELD 1 +#define configUSE_MUTEXES 1 +#define configUSE_RECURSIVE_MUTEXES 1 +#define configUSE_COUNTING_SEMAPHORES 1 +#define configQUEUE_REGISTRY_SIZE 4 +#define configUSE_QUEUE_SETS 0 +#define configUSE_TIME_SLICING 0 +#define configUSE_NEWLIB_REENTRANT 0 +#define configENABLE_BACKWARD_COMPATIBILITY 1 +#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 + +#define configSUPPORT_STATIC_ALLOCATION 1 +#define configSUPPORT_DYNAMIC_ALLOCATION 0 + +/* Hook function related definitions. */ +#define configUSE_IDLE_HOOK 0 +#define configUSE_TICK_HOOK 0 +#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning +#define configCHECK_FOR_STACK_OVERFLOW 2 +#define configCHECK_HANDLER_INSTALLATION 0 + +/* Run time and task stats gathering related definitions. */ +#define configGENERATE_RUN_TIME_STATS 0 +#define configRECORD_STACK_HIGH_ADDRESS 1 +#define configUSE_TRACE_FACILITY 1 // legacy trace +#define configUSE_STATS_FORMATTING_FUNCTIONS 0 + +/* Co-routine definitions. */ +#define configUSE_CO_ROUTINES 0 +#define configMAX_CO_ROUTINE_PRIORITIES 2 + +/* Software timer related definitions. */ +#define configUSE_TIMERS 1 +#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) +#define configTIMER_QUEUE_LENGTH 32 +#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE + +/* Optional functions - most linkers will remove unused functions anyway. */ +#define INCLUDE_vTaskPrioritySet 0 +#define INCLUDE_uxTaskPriorityGet 0 +#define INCLUDE_vTaskDelete 0 +#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY +#define INCLUDE_xResumeFromISR 0 +#define INCLUDE_vTaskDelayUntil 1 +#define INCLUDE_vTaskDelay 1 +#define INCLUDE_xTaskGetSchedulerState 0 +#define INCLUDE_xTaskGetCurrentTaskHandle 1 +#define INCLUDE_uxTaskGetStackHighWaterMark 0 +#define INCLUDE_xTaskGetIdleTaskHandle 0 +#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 +#define INCLUDE_pcTaskGetTaskName 0 +#define INCLUDE_eTaskGetState 0 +#define INCLUDE_xEventGroupSetBitFromISR 0 +#define INCLUDE_xTimerPendFunctionCall 0 + +/* FreeRTOS hooks to NVIC vectors */ +#define xPortPendSVHandler PendSV_Handler +#define xPortSysTickHandler SysTick_Handler +#define vPortSVCHandler SVC_Handler + +//--------------------------------------------------------------------+ +// Interrupt nesting behavior configuration. +//--------------------------------------------------------------------+ + +// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header +#define configPRIO_BITS 3 + +/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1<FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO12M */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO12M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK; +} +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO24M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO24M +outputs: +- {id: CLK_1M_clock.outFreq, value: 1 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CPU_clock.outFreq, value: 24 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_DIV_clock.outFreq, value: 48 MHz} +- {id: FRO_HF_clock.outFreq, value: 48 MHz} +- {id: MAIN_clock.outFreq, value: 48 MHz} +- {id: Slow_clock.outFreq, value: 6 MHz} +- {id: System_clock.outFreq, value: 24 MHz} +settings: +- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} +- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO24M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO24M configuration + ******************************************************************************/ +void BOARD_BootClockFRO24M(void) +{ + uint32_t coreFreq; + spc_active_mode_core_ldo_option_t ldoOption; + spc_sram_voltage_config_t sramOption; + + /* Get the CPU Core frequency */ + coreFreq = CLOCK_GetCoreSysClkFreq(); + + /* The flow of increasing voltage and frequency */ + if (coreFreq <= BOARD_BOOTCLOCKFRO24M_CORE_CLOCK) { + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO24M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 2U); /* !< Set AHBCLKDIV divider to value 2 */ + CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO24M_CORE_CLOCK; +} +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO48M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO48M +outputs: +- {id: CLK_1M_clock.outFreq, value: 1 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CPU_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_DIV_clock.outFreq, value: 48 MHz} +- {id: FRO_HF_clock.outFreq, value: 48 MHz} +- {id: MAIN_clock.outFreq, value: 48 MHz} +- {id: Slow_clock.outFreq, value: 12 MHz} +- {id: System_clock.outFreq, value: 48 MHz} +settings: +- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO48M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO48M configuration + ******************************************************************************/ +void BOARD_BootClockFRO48M(void) +{ + uint32_t coreFreq; + spc_active_mode_core_ldo_option_t ldoOption; + spc_sram_voltage_config_t sramOption; + + /* Get the CPU Core frequency */ + coreFreq = CLOCK_GetCoreSysClkFreq(); + + /* The flow of increasing voltage and frequency */ + if (coreFreq <= BOARD_BOOTCLOCKFRO48M_CORE_CLOCK) { + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO48M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ + CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO48M_CORE_CLOCK; +} +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO64M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO64M +outputs: +- {id: CLK_1M_clock.outFreq, value: 1 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CPU_clock.outFreq, value: 64 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_DIV_clock.outFreq, value: 64 MHz} +- {id: FRO_HF_clock.outFreq, value: 64 MHz} +- {id: MAIN_clock.outFreq, value: 64 MHz} +- {id: Slow_clock.outFreq, value: 16 MHz} +- {id: System_clock.outFreq, value: 64 MHz} +settings: +- {id: VDD_CORE, value: voltage_1v1} +- {id: MRCC.FROHFDIV.scale, value: '1', locked: true} +- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} +- {id: SYSCON.AHBCLKDIV.scale, value: '1', locked: true} +sources: +- {id: SCG.FIRC.outFreq, value: 64 MHz} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO64M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO64M configuration + ******************************************************************************/ +void BOARD_BootClockFRO64M(void) +{ + uint32_t coreFreq; + spc_active_mode_core_ldo_option_t ldoOption; + spc_sram_voltage_config_t sramOption; + + /* Get the CPU Core frequency */ + coreFreq = CLOCK_GetCoreSysClkFreq(); + + /* The flow of increasing voltage and frequency */ + if (coreFreq <= BOARD_BOOTCLOCKFRO64M_CORE_CLOCK) { + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P1V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFROHFClocking(64000000U); /*!< Enable FRO HF(64MHz) output */ + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO64M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P1V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ + CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO64M_CORE_CLOCK; +} +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO96M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO96M +called_from_default_init: true +outputs: +- {id: CLK_1M_clock.outFreq, value: 1 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CPU_clock.outFreq, value: 96 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_DIV_clock.outFreq, value: 96 MHz} +- {id: FRO_HF_clock.outFreq, value: 96 MHz} +- {id: MAIN_clock.outFreq, value: 96 MHz} +- {id: Slow_clock.outFreq, value: 24 MHz} +- {id: System_clock.outFreq, value: 96 MHz} +settings: +- {id: VDD_CORE, value: voltage_1v1} +- {id: CLKOUTDIV_HALT, value: Enable} +- {id: MRCC.FROHFDIV.scale, value: '1', locked: true} +- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} +- {id: SYSCON.AHBCLKDIV.scale, value: '1', locked: true} +sources: +- {id: SCG.FIRC.outFreq, value: 96 MHz} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO96M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO96M configuration + ******************************************************************************/ +void BOARD_BootClockFRO96M(void) +{ + uint32_t coreFreq; + spc_active_mode_core_ldo_option_t ldoOption; + spc_sram_voltage_config_t sramOption; + + /* Get the CPU Core frequency */ + coreFreq = CLOCK_GetCoreSysClkFreq(); + + /* The flow of increasing voltage and frequency */ + if (coreFreq <= BOARD_BOOTCLOCKFRO96M_CORE_CLOCK) { + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x2U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P1V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFROHFClocking(96000000U); /*!< Enable FRO HF(96MHz) output */ + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO96M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x2U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P1V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ + CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO96M_CORE_CLOCK; +} diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h b/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h new file mode 100644 index 000000000..079d0d312 --- /dev/null +++ b/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h @@ -0,0 +1,170 @@ +/* + * Copyright 2023 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +#ifndef _CLOCK_CONFIG_H_ +#define _CLOCK_CONFIG_H_ + +#include "fsl_common.h" + +/******************************************************************************* + * Definitions + ******************************************************************************/ + +/******************************************************************************* + ************************ BOARD_InitBootClocks function ************************ + ******************************************************************************/ + +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes default configuration of clocks. + * + */ +void BOARD_InitBootClocks(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO12M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK 12000000U /*!< Core clock frequency: 12000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO12M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO24M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO24M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO24M_CORE_CLOCK 24000000U /*!< Core clock frequency: 24000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO24M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO24M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO48M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO48M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO48M_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO48M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO48M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO64M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO64M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO64M_CORE_CLOCK 64000000U /*!< Core clock frequency: 64000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO64M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO64M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO96M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO96M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO96M_CORE_CLOCK 96000000U /*!< Core clock frequency: 96000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO96M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO96M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c new file mode 100644 index 000000000..b0e6de560 --- /dev/null +++ b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c @@ -0,0 +1,159 @@ +/* + * Copyright 2023 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +/* clang-format off */ +/* + * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!GlobalInfo +product: Pins v14.0 +processor: MCXA153 +package_id: MCXA153VLH +mcu_data: ksdk2_0 +processor_version: 0.14.3 +pin_labels: +- {pin_num: '38', pin_signal: P3_12/LPUART2_RTS_B/CT1_MAT2/PWM0_X0, label: LED_RED, identifier: LED_RED} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** + */ +/* clang-format on */ + +#include "fsl_common.h" +#include "fsl_port.h" +#include "fsl_gpio.h" +#include "pin_mux.h" + +/* FUNCTION ************************************************************************************************************ + * + * Function Name : BOARD_InitBootPins + * Description : Calls initialization functions. + * + * END ****************************************************************************************************************/ +void BOARD_InitBootPins(void) +{ + BOARD_InitPins(); +} + +/* clang-format off */ +/* + * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +BOARD_InitPins: +- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'} +- pin_list: + - {pin_num: '38', peripheral: GPIO3, signal: 'GPIO, 12', pin_signal: P3_12/LPUART2_RTS_B/CT1_MAT2/PWM0_X0, direction: OUTPUT, gpio_init_state: 'false', slew_rate: fast, + open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** + */ +/* clang-format on */ + +/* FUNCTION ************************************************************************************************************ + * + * Function Name : BOARD_InitPins + * Description : Configures pin routing and optionally pin electrical features. + * + * END ****************************************************************************************************************/ +void BOARD_InitPins(void) +{ + RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn); + RESET_PeripheralReset(kPORT0_RST_SHIFT_RSTn); + CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u); + CLOCK_AttachClk(kFRO12M_to_LPUART0); + + /* write to PORT0: Peripheral clock is enabled */ + CLOCK_EnableClock(kCLOCK_GatePORT0); + + /* Write to GPIO3: Peripheral clock is enabled */ + CLOCK_EnableClock(kCLOCK_GateGPIO3); + /* Write to PORT3: Peripheral clock is enabled */ + CLOCK_EnableClock(kCLOCK_GatePORT3); + /* GPIO3 peripheral is released from reset */ + RESET_ReleasePeripheralReset(kGPIO3_RST_SHIFT_RSTn); + /* PORT3 peripheral is released from reset */ + RESET_ReleasePeripheralReset(kPORT3_RST_SHIFT_RSTn); + + const port_pin_config_t port3_12_pin38_config = {/* Internal pull-up/down resistor is disabled */ + kPORT_PullDisable, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Normal drive strength is configured */ + kPORT_NormalDriveStrength, + /* Pin is configured as P3_12 */ + kPORT_MuxAlt0, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT3_12 (pin 38) is configured as P3_12 */ + PORT_SetPinConfig(PORT3, 12U, &port3_12_pin38_config); + + const port_pin_config_t port0_2_pin51_config = {/* Internal pull-up resistor is enabled */ + kPORT_PullUp, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Normal drive strength is configured */ + kPORT_NormalDriveStrength, + /* Pin is configured as LPUART0_RXD */ + kPORT_MuxAlt2, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT0_2 (pin 51) is configured as LPUART0_RXD */ + PORT_SetPinConfig(PORT0, 2U, &port0_2_pin51_config); + + const port_pin_config_t port0_3_pin52_config = {/* Internal pull-up resistor is enabled */ + kPORT_PullUp, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Normal drive strength is configured */ + kPORT_NormalDriveStrength, + /* Pin is configured as LPUART0_TXD */ + kPORT_MuxAlt2, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT0_3 (pin 52) is configured as LPUART0_TXD */ + PORT_SetPinConfig(PORT0, 3U, &port0_3_pin52_config); + +} +/*********************************************************************************************************************** + * EOF + **********************************************************************************************************************/ diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h new file mode 100644 index 000000000..06b6fdee9 --- /dev/null +++ b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h @@ -0,0 +1,47 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#ifndef _PIN_MUX_H_ +#define _PIN_MUX_H_ + +/*! + * @addtogroup pin_mux + * @{ + */ + +/*********************************************************************************************************************** + * API + **********************************************************************************************************************/ + +#if defined(__cplusplus) +extern "C" { +#endif + +/*! + * @brief Calls initialization functions. + * + */ +void BOARD_InitBootPins(void); + +/*! + * @brief Configures pin routing and optionally pin electrical features. + * + */ +void BOARD_InitPins(void); + +#if defined(__cplusplus) +} +#endif + +/*! + * @} + */ +#endif /* _PIN_MUX_H_ */ + +/*********************************************************************************************************************** + * EOF + **********************************************************************************************************************/ diff --git a/hw/bsp/mcxa/debug.jlinkscript b/hw/bsp/mcxa/debug.jlinkscript new file mode 100644 index 000000000..fd8bcffef --- /dev/null +++ b/hw/bsp/mcxa/debug.jlinkscript @@ -0,0 +1,5 @@ +int SetupTarget(void) { + JLINK_ExecCommand("SetRTTSearchRanges 0x20000000 0x40000"); + + return 0; +} diff --git a/hw/bsp/mcxa/family.c b/hw/bsp/mcxa/family.c new file mode 100644 index 000000000..97abc1bc3 --- /dev/null +++ b/hw/bsp/mcxa/family.c @@ -0,0 +1,163 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2018, hathach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board_api.h" +#include "fsl_device_registers.h" +#include "fsl_gpio.h" +#include "fsl_lpuart.h" +#include "board.h" + +#include "pin_mux.h" +#include "clock_config.h" +#include "fsl_common.h" + + +#ifdef BOARD_TUD_RHPORT + #define PORT_SUPPORT_DEVICE(_n) (BOARD_TUD_RHPORT == _n) +#else + #define PORT_SUPPORT_DEVICE(_n) 0 +#endif + +#ifdef BOARD_TUH_RHPORT + #define PORT_SUPPORT_HOST(_n) (BOARD_TUH_RHPORT == _n) +#else + #define PORT_SUPPORT_HOST(_n) 0 +#endif + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ +void USB0_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +void board_init(void) +{ + BOARD_InitPins(); + BOARD_InitBootClocks(); + CLOCK_SetupExtClocking(XTAL0_CLK_HZ); + + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + + // LED + CLOCK_EnableClock(LED_CLK); + gpio_pin_config_t LED_RED_config = { + .pinDirection = kGPIO_DigitalOutput, + .outputLogic = 0U + }; + + /* Initialize GPIO functionality on pin PIO3_12 (pin 38) */ + GPIO_PinInit(LED_GPIO, LED_PIN, &LED_RED_config); + board_led_write(1); + + // Button +#ifdef BUTTON_GPIO + CLOCK_EnableClock(BUTTON_CLK); + gpio_pin_config_t const button_config = { kGPIO_DigitalInput, 0}; + GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); +#endif + +#ifdef UART_DEV + + CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u); + CLOCK_AttachClk(kFRO12M_to_LPUART0); + RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn); + + lpuart_config_t uart_config; + LPUART_GetDefaultConfig(&uart_config); + uart_config.baudRate_Bps = 115200; + uart_config.enableTx = true; + uart_config.enableRx = true; + LPUART_Init(UART_DEV, &uart_config, 12000000u); + + +#endif + + // USB VBUS + /* PORT0 PIN22 configured as USB0_VBUS */ + +#if PORT_SUPPORT_DEVICE(0) + // Port0 is Full Speed + + RESET_PeripheralReset(kUSB0_RST_SHIFT_RSTn); + CLOCK_EnableUsbfsClock(); +#endif + +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +} + +uint32_t board_button_read(void) +{ +#ifdef BUTTON_GPIO + return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); +#else + return 1; +#endif +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ +#ifdef UART_DEV + LPUART_WriteBlocking(UART_DEV, (uint8_t const *) buf, len); + return len; +#else + (void) buf; (void) len; + return 0; +#endif +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif diff --git a/hw/bsp/mcxa/family.cmake b/hw/bsp/mcxa/family.cmake new file mode 100644 index 000000000..0aa690afc --- /dev/null +++ b/hw/bsp/mcxa/family.cmake @@ -0,0 +1,110 @@ +include_guard() + +if (NOT BOARD) + message(FATAL_ERROR "BOARD not specified") +endif () + +set(SDK_DIR ${TOP}/hw/mcu/nxp/mcux-sdk) +set(CMSIS_DIR ${TOP}/lib/CMSIS_5) + +# include board specific +include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) + +# toolchain set up +set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor") +set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOLCHAIN}.cmake) + +set(FAMILY_MCUS MCXA CACHE INTERNAL "") + + +#------------------------------------ +# BOARD_TARGET +#------------------------------------ +# only need to be built ONCE for all examples +function(add_board_target BOARD_TARGET) + if (NOT TARGET ${BOARD_TARGET}) + add_library(${BOARD_TARGET} STATIC + # external driver + #lib/sct_neopixel/sct_neopixel.c + + # driver + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_gpio.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_common_arm.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpuart.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpflexcomm.c + # mcu + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_reset.c + ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_CORE}.c + ) + # target_compile_definitions(${BOARD_TARGET} PUBLIC + # ) + target_include_directories(${BOARD_TARGET} PUBLIC + # driver + # mcu + ${CMSIS_DIR}/CMSIS/Core/Include + ${SDK_DIR}/devices/${MCU_VARIANT} + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers + ) + + update_board(${BOARD_TARGET}) + + if (CMAKE_C_COMPILER_ID STREQUAL "GNU") + target_sources(${BOARD_TARGET} PUBLIC + ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_CORE}.S + ) + target_link_options(${BOARD_TARGET} PUBLIC + # linker file + "LINKER:--script=${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_CORE}_flash.ld" + # nanolib + --specs=nosys.specs + --specs=nano.specs + ) + elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--config=${LD_FILE_IAR}" + ) + endif () + endif () +endfunction() + + +#------------------------------------ +# Functions +#------------------------------------ +function(family_configure_example TARGET RTOS) + family_configure_common(${TARGET} ${RTOS}) + + # Board target + add_board_target(board_${BOARD}) + + #---------- Port Specific ---------- + # These files are built for each example since it depends on example's tusb_config.h + target_sources(${TARGET} PUBLIC + # BSP + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c + ) + target_include_directories(${TARGET} PUBLIC + # family, hw, board + ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../ + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} + ) + + # Add TinyUSB target and port source + family_add_tinyusb(${TARGET} OPT_MCU_MCXA ${RTOS}) + target_sources(${TARGET}-tinyusb PUBLIC + # TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS + ${TOP}/src/portable/chipidea/ci_fs/dcd_ci_fs.c + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) + + # Link dependencies + target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) + + # Flashing + family_flash_jlink(${TARGET}) + #family_flash_nxplink(${TARGET}) + #family_flash_pyocd(${TARGET}) +endfunction() diff --git a/hw/bsp/mcxa/family.mk b/hw/bsp/mcxa/family.mk new file mode 100644 index 000000000..b32282d04 --- /dev/null +++ b/hw/bsp/mcxa/family.mk @@ -0,0 +1,42 @@ +UF2_FAMILY_ID = 0x2abc77ec +SDK_DIR = hw/mcu/nxp/mcux-sdk + +DEPS_SUBMODULES += $(SDK_DIR) lib/CMSIS_5 #not found + +include $(TOP)/$(BOARD_PATH)/board.mk +CPU_CORE ?= cortex-m33 + +CFLAGS += \ + -flto \ + -DCFG_TUSB_MCU=OPT_MCU_MCXA \ + -DBOARD_TUD_RHPORT=0 + +# mcu driver cause following warnings +CFLAGS += -Wno-error=unused-parameter -Wno-error=old-style-declaration + +LDFLAGS_GCC += -specs=nosys.specs -specs=nano.specs + +# All source paths should be relative to the top level. +LD_FILE ?= $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/$(MCU_CORE)_flash.ld + +# TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS +$(info "PORT0 Full Speed") +CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED +SRC_C += src/portable/chipidea/ci_fs/dcd_ci_fs.c + +SRC_C += \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/system_$(MCU_CORE).c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_clock.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_reset.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_gpio.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpuart.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_common_arm.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_spc.c +INC += \ + $(TOP)/$(BOARD_PATH) \ + $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ + $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT) \ + $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers + + +SRC_S += $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/startup_$(MCU_CORE).S diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index e589c4c86..21ae3a71e 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -100,6 +100,13 @@ #define TUP_DCD_ENDPOINT_MAX 8 #define TUP_RHPORT_HIGHSPEED 1 +#elif TU_CHECK_MCU(OPT_MCU_MCXA) + // USB0 is chipidea FS + #define TUP_USBIP_CHIPIDEA_FS + #define TUP_USBIP_CHIPIDEA_FS_MCXA + + #define TUP_DCD_ENDPOINT_MAX 16 + #elif TU_CHECK_MCU(OPT_MCU_MIMXRT1XXX) #define TUP_USBIP_CHIPIDEA_HS #define TUP_USBIP_EHCI diff --git a/src/portable/chipidea/ci_fs/ci_fs_mcxa.h b/src/portable/chipidea/ci_fs/ci_fs_mcxa.h new file mode 100644 index 000000000..81786efdf --- /dev/null +++ b/src/portable/chipidea/ci_fs/ci_fs_mcxa.h @@ -0,0 +1,47 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2023 Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef _CI_FS_MCXA_H +#define _CI_FS_MCXA_H + +#include "fsl_device_registers.h" + +#define CI_FS_REG(_port) ((ci_fs_regs_t*) USB0_BASE) +#define CI_REG CI_FS_REG(0) + +void dcd_int_enable(uint8_t rhport) +{ + (void) rhport; + NVIC_EnableIRQ(USB0_IRQn); +} + +void dcd_int_disable(uint8_t rhport) +{ + (void) rhport; + NVIC_DisableIRQ(USB0_IRQn); +} + +#endif diff --git a/src/portable/chipidea/ci_fs/dcd_ci_fs.c b/src/portable/chipidea/ci_fs/dcd_ci_fs.c index 9327e09d8..08e73711f 100644 --- a/src/portable/chipidea/ci_fs/dcd_ci_fs.c +++ b/src/portable/chipidea/ci_fs/dcd_ci_fs.c @@ -35,6 +35,8 @@ #include "ci_fs_kinetis.h" #elif defined(TUP_USBIP_CHIPIDEA_FS_MCX) #include "ci_fs_mcx.h" +#elif defined(TUP_USBIP_CHIPIDEA_FS_MCXA) + #include "ci_fs_mcxa.h" #else #error "MCU is not supported" #endif diff --git a/src/tusb_option.h b/src/tusb_option.h index 767323bdd..fe9c44e96 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -175,6 +175,7 @@ // NXP LPC MCX #define OPT_MCU_MCXN9 2300 ///< NXP MCX N9 Series +#define OPT_MCU_MCXA 2301 ///< NXP MCX A Series // Check if configured MCU is one of listed // Apply _TU_CHECK_MCU with || as separator to list of input -- cgit v1.3.1 From 68bb85840639b2a3d8c4ad51e31245bd039e5b9f Mon Sep 17 00:00:00 2001 From: Jerzy Kasenberg Date: Mon, 12 Feb 2024 16:12:32 +0100 Subject: nrf5x: Handle ISOOUT CRC errors NRF5x USB controller can detect ISO OUT CRC errors. In such case USBEVENT is signaled with EVENTCAUSE_ISOOUTCRC set. Even if controller detects corrupted ISO OUT packet it allows to data transfer from ednpoint to RAM however packet is corrupted and code could just as well drop packet altogether. With current implementation incoming ISO OUT packets were put in FIFO and exact information how much data already in FIFO is correct was hard to keep track of. If was observed that on certain configurations HS hub when FS device was connected occasionally sent invalid (short) packet. In such case if packet length was reported odd audio stream was not recognizable any more. With this change corrupted packets are not passed to upper layers and are silently dropped. --- src/portable/nordic/nrf5x/dcd_nrf5x.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'src/portable') diff --git a/src/portable/nordic/nrf5x/dcd_nrf5x.c b/src/portable/nordic/nrf5x/dcd_nrf5x.c index 4e702aed4..841cda752 100644 --- a/src/portable/nordic/nrf5x/dcd_nrf5x.c +++ b/src/portable/nordic/nrf5x/dcd_nrf5x.c @@ -653,7 +653,11 @@ void dcd_int_handler(uint8_t rhport) if (NRF_USBD->EPOUTEN & USBD_EPOUTEN_ISOOUT_Msk) { iso_enabled = true; - xact_out_dma(EP_ISO_NUM); + // Transfer from endpoint to RAM only if data is not corrupted + if ((int_status & USBD_INTEN_USBEVENT_Msk) == 0 || + (NRF_USBD->EVENTCAUSE & USBD_EVENTCAUSE_ISOOUTCRC_Msk) == 0) { + xact_out_dma(EP_ISO_NUM); + } } // ISOIN: Notify client that data was transferred @@ -683,7 +687,7 @@ void dcd_int_handler(uint8_t rhport) { TU_LOG(2, "EVENTCAUSE = 0x%04lX\r\n", NRF_USBD->EVENTCAUSE); - enum { EVT_CAUSE_MASK = USBD_EVENTCAUSE_SUSPEND_Msk | USBD_EVENTCAUSE_RESUME_Msk | USBD_EVENTCAUSE_USBWUALLOWED_Msk }; + enum { EVT_CAUSE_MASK = USBD_EVENTCAUSE_SUSPEND_Msk | USBD_EVENTCAUSE_RESUME_Msk | USBD_EVENTCAUSE_USBWUALLOWED_Msk | USBD_EVENTCAUSE_ISOOUTCRC_Msk }; uint32_t const evt_cause = NRF_USBD->EVENTCAUSE & EVT_CAUSE_MASK; NRF_USBD->EVENTCAUSE = evt_cause; // clear interrupt -- cgit v1.3.1 From 5ca99800604ec3ed9d45bf4660db04101aa737ce Mon Sep 17 00:00:00 2001 From: Chris Desjardins Date: Thu, 15 Feb 2024 16:27:49 +0100 Subject: Do not enable the Mode mismatch interrupt source, it is not cleared If this interrupt ever hits it will result in an infinite interrupt loop as it is never cleared. --- src/portable/synopsys/dwc2/dcd_dwc2.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index 3e15d51c6..3f00243e5 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -462,9 +462,7 @@ void dcd_init(uint8_t rhport) { dwc2->gotgint |= int_mask; // Required as part of core initialization. - // TODO: How should mode mismatch be handled? It will cause - // the core to stop working/require reset. - dwc2->gintmsk = GINTMSK_OTGINT | GINTMSK_MMISM | GINTMSK_RXFLVLM | + dwc2->gintmsk = GINTMSK_OTGINT | GINTMSK_RXFLVLM | GINTMSK_USBSUSPM | GINTMSK_USBRST | GINTMSK_ENUMDNEM | GINTMSK_WUIM; // Enable global interrupt -- cgit v1.3.1 From e9dc8f3e7dc6799ad674139df97e253acc71f4d7 Mon Sep 17 00:00:00 2001 From: Ha Thach Date: Mon, 19 Feb 2024 18:12:03 +0700 Subject: fix wrong volatile usage in ohci gtd --- src/portable/ohci/ohci.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/ohci/ohci.h b/src/portable/ohci/ohci.h index 4feefd771..94bad5df7 100644 --- a/src/portable/ohci/ohci.h +++ b/src/portable/ohci/ohci.h @@ -83,7 +83,7 @@ typedef struct TU_ATTR_ALIGNED(16) volatile uint32_t condition_code : 4; // Word 1 - volatile uint8_t* current_buffer_pointer; + uint8_t* volatile current_buffer_pointer; // Word 2 : next TD volatile uint32_t next; -- cgit v1.3.1 From 5c14bd13da211ff2679115b0dba96ac80c1a516c Mon Sep 17 00:00:00 2001 From: Jerry Palacios Date: Tue, 20 Feb 2024 18:02:42 -0600 Subject: MCX A and MCX N merged to MCX family --- README.rst | 4 +- hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h | 149 ++++++++ hw/bsp/mcx/boards/frdmmcxa153/board.cmake | 23 ++ hw/bsp/mcx/boards/frdmmcxa153/board.h | 66 ++++ hw/bsp/mcx/boards/frdmmcxa153/board.mk | 14 + hw/bsp/mcx/boards/frdmmcxa153/clock_config.c | 468 ++++++++++++++++++++++++++ hw/bsp/mcx/boards/frdmmcxa153/clock_config.h | 170 ++++++++++ hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c | 159 +++++++++ hw/bsp/mcx/boards/frdmmcxa153/pin_mux.h | 47 +++ hw/bsp/mcx/boards/frdmmcxn947/board.cmake | 24 ++ hw/bsp/mcx/boards/frdmmcxn947/board.h | 66 ++++ hw/bsp/mcx/boards/frdmmcxn947/board.mk | 14 + hw/bsp/mcx/boards/frdmmcxn947/clock_config.c | 338 +++++++++++++++++++ hw/bsp/mcx/boards/frdmmcxn947/clock_config.h | 177 ++++++++++ hw/bsp/mcx/boards/frdmmcxn947/pin_mux.c | 143 ++++++++ hw/bsp/mcx/boards/frdmmcxn947/pin_mux.h | 51 +++ hw/bsp/mcx/boards/mcxn947brk/board.cmake | 24 ++ hw/bsp/mcx/boards/mcxn947brk/board.h | 66 ++++ hw/bsp/mcx/boards/mcxn947brk/board.mk | 14 + hw/bsp/mcx/boards/mcxn947brk/clock_config.c | 338 +++++++++++++++++++ hw/bsp/mcx/boards/mcxn947brk/clock_config.h | 177 ++++++++++ hw/bsp/mcx/boards/mcxn947brk/pin_mux.c | 141 ++++++++ hw/bsp/mcx/boards/mcxn947brk/pin_mux.h | 51 +++ hw/bsp/mcx/debug.jlinkscript | 5 + hw/bsp/mcx/family.c | 267 +++++++++++++++ hw/bsp/mcx/family.cmake | 122 +++++++ hw/bsp/mcx/family.mk | 65 ++++ hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h | 149 -------- hw/bsp/mcxa/boards/frdmmcxa153/board.cmake | 18 - hw/bsp/mcxa/boards/frdmmcxa153/board.h | 66 ---- hw/bsp/mcxa/boards/frdmmcxa153/board.mk | 13 - hw/bsp/mcxa/boards/frdmmcxa153/clock_config.c | 468 -------------------------- hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h | 170 ---------- hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c | 159 --------- hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h | 47 --- hw/bsp/mcxa/debug.jlinkscript | 5 - hw/bsp/mcxa/family.c | 161 --------- hw/bsp/mcxa/family.cmake | 110 ------ hw/bsp/mcxa/family.mk | 42 --- hw/bsp/mcxn/FreeRTOSConfig/FreeRTOSConfig.h | 149 -------- hw/bsp/mcxn/boards/frdmmcxn947/board.cmake | 21 -- hw/bsp/mcxn/boards/frdmmcxn947/board.h | 66 ---- hw/bsp/mcxn/boards/frdmmcxn947/board.mk | 11 - hw/bsp/mcxn/boards/frdmmcxn947/clock_config.c | 338 ------------------- hw/bsp/mcxn/boards/frdmmcxn947/clock_config.h | 177 ---------- hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.c | 143 -------- hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.h | 51 --- hw/bsp/mcxn/boards/mcxn947brk/board.cmake | 21 -- hw/bsp/mcxn/boards/mcxn947brk/board.h | 66 ---- hw/bsp/mcxn/boards/mcxn947brk/board.mk | 11 - hw/bsp/mcxn/boards/mcxn947brk/clock_config.c | 338 ------------------- hw/bsp/mcxn/boards/mcxn947brk/clock_config.h | 177 ---------- hw/bsp/mcxn/boards/mcxn947brk/pin_mux.c | 141 -------- hw/bsp/mcxn/boards/mcxn947brk/pin_mux.h | 51 --- hw/bsp/mcxn/debug.jlinkscript | 5 - hw/bsp/mcxn/family.c | 245 -------------- hw/bsp/mcxn/family.cmake | 110 ------ hw/bsp/mcxn/family.mk | 51 --- src/common/tusb_mcu.h | 4 +- src/portable/chipidea/ci_fs/ci_fs_mcx.h | 17 +- src/portable/chipidea/ci_fs/ci_fs_mcxa.h | 47 --- src/portable/chipidea/ci_fs/dcd_ci_fs.c | 2 - src/tusb_option.h | 2 +- 63 files changed, 3197 insertions(+), 3638 deletions(-) create mode 100644 hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h create mode 100644 hw/bsp/mcx/boards/frdmmcxa153/board.cmake create mode 100644 hw/bsp/mcx/boards/frdmmcxa153/board.h create mode 100644 hw/bsp/mcx/boards/frdmmcxa153/board.mk create mode 100644 hw/bsp/mcx/boards/frdmmcxa153/clock_config.c create mode 100644 hw/bsp/mcx/boards/frdmmcxa153/clock_config.h create mode 100644 hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c create mode 100644 hw/bsp/mcx/boards/frdmmcxa153/pin_mux.h create mode 100644 hw/bsp/mcx/boards/frdmmcxn947/board.cmake create mode 100644 hw/bsp/mcx/boards/frdmmcxn947/board.h create mode 100644 hw/bsp/mcx/boards/frdmmcxn947/board.mk create mode 100644 hw/bsp/mcx/boards/frdmmcxn947/clock_config.c create mode 100644 hw/bsp/mcx/boards/frdmmcxn947/clock_config.h create mode 100644 hw/bsp/mcx/boards/frdmmcxn947/pin_mux.c create mode 100644 hw/bsp/mcx/boards/frdmmcxn947/pin_mux.h create mode 100644 hw/bsp/mcx/boards/mcxn947brk/board.cmake create mode 100644 hw/bsp/mcx/boards/mcxn947brk/board.h create mode 100644 hw/bsp/mcx/boards/mcxn947brk/board.mk create mode 100644 hw/bsp/mcx/boards/mcxn947brk/clock_config.c create mode 100644 hw/bsp/mcx/boards/mcxn947brk/clock_config.h create mode 100644 hw/bsp/mcx/boards/mcxn947brk/pin_mux.c create mode 100644 hw/bsp/mcx/boards/mcxn947brk/pin_mux.h create mode 100644 hw/bsp/mcx/debug.jlinkscript create mode 100644 hw/bsp/mcx/family.c create mode 100644 hw/bsp/mcx/family.cmake create mode 100644 hw/bsp/mcx/family.mk delete mode 100644 hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h delete mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/board.cmake delete mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/board.h delete mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/board.mk delete mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/clock_config.c delete mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h delete mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c delete mode 100644 hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h delete mode 100644 hw/bsp/mcxa/debug.jlinkscript delete mode 100644 hw/bsp/mcxa/family.c delete mode 100644 hw/bsp/mcxa/family.cmake delete mode 100644 hw/bsp/mcxa/family.mk delete mode 100644 hw/bsp/mcxn/FreeRTOSConfig/FreeRTOSConfig.h delete mode 100644 hw/bsp/mcxn/boards/frdmmcxn947/board.cmake delete mode 100644 hw/bsp/mcxn/boards/frdmmcxn947/board.h delete mode 100644 hw/bsp/mcxn/boards/frdmmcxn947/board.mk delete mode 100644 hw/bsp/mcxn/boards/frdmmcxn947/clock_config.c delete mode 100644 hw/bsp/mcxn/boards/frdmmcxn947/clock_config.h delete mode 100644 hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.c delete mode 100644 hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.h delete mode 100644 hw/bsp/mcxn/boards/mcxn947brk/board.cmake delete mode 100644 hw/bsp/mcxn/boards/mcxn947brk/board.h delete mode 100644 hw/bsp/mcxn/boards/mcxn947brk/board.mk delete mode 100644 hw/bsp/mcxn/boards/mcxn947brk/clock_config.c delete mode 100644 hw/bsp/mcxn/boards/mcxn947brk/clock_config.h delete mode 100644 hw/bsp/mcxn/boards/mcxn947brk/pin_mux.c delete mode 100644 hw/bsp/mcxn/boards/mcxn947brk/pin_mux.h delete mode 100644 hw/bsp/mcxn/debug.jlinkscript delete mode 100644 hw/bsp/mcxn/family.c delete mode 100644 hw/bsp/mcxn/family.cmake delete mode 100644 hw/bsp/mcxn/family.mk delete mode 100644 src/portable/chipidea/ci_fs/ci_fs_mcxa.h (limited to 'src/portable') diff --git a/README.rst b/README.rst index c48007c23..8c3145d33 100644 --- a/README.rst +++ b/README.rst @@ -139,9 +139,7 @@ Following CPUs are supported, check out `Supported Devices`_ for comprehensive l | +---------+--------------------------------------------------+ | | LPC | 11u, 13, 15, 17, 18, 40, 43, 51u, 54, 55 | | +---------+--------------------------------------------------+ -| | MCXA | A153 | -| +---------+--------------------------------------------------+ -| | MCXN | N9 | +| | MCX | A15, N9 | +--------------+---------+--------------------------------------------------+ | Raspberry Pi | RP2040 | +--------------+-----+------------------------------------------------------+ diff --git a/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h new file mode 100644 index 000000000..6f10a7ab0 --- /dev/null +++ b/hw/bsp/mcx/FreeRTOSConfig/FreeRTOSConfig.h @@ -0,0 +1,149 @@ +/* + * FreeRTOS Kernel V10.0.0 + * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. + * + * Permission is hereby granted, free of charge, to any person obtaining a copy of + * this software and associated documentation files (the "Software"), to deal in + * the Software without restriction, including without limitation the rights to + * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of + * the Software, and to permit persons to whom the Software is furnished to do so, + * subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in all + * copies or substantial portions of the Software. If you wish to use our Amazon + * FreeRTOS name, please do so in a fair use way that does not cause confusion. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS + * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR + * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER + * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN + * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. + * + * http://www.FreeRTOS.org + * http://aws.amazon.com/freertos + * + * 1 tab == 4 spaces! + */ + + +#ifndef FREERTOS_CONFIG_H +#define FREERTOS_CONFIG_H + +/*----------------------------------------------------------- + * Application specific definitions. + * + * These definitions should be adjusted for your particular hardware and + * application requirements. + * + * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE + * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. + * + * See http://www.freertos.org/a00110.html. + *----------------------------------------------------------*/ + +// skip if included from IAR assembler +#ifndef __IASMARM__ + #include "fsl_device_registers.h" +#endif + +/* Cortex M23/M33 port configuration. */ +#define configENABLE_MPU 0 +#define configENABLE_FPU 1 +#define configENABLE_TRUSTZONE 0 +#define configMINIMAL_SECURE_STACK_SIZE (1024) + +#define configUSE_PREEMPTION 1 +#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 +#define configCPU_CLOCK_HZ SystemCoreClock +#define configTICK_RATE_HZ ( 1000 ) +#define configMAX_PRIORITIES ( 5 ) +#define configMINIMAL_STACK_SIZE ( 128 ) +#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) +#define configMAX_TASK_NAME_LEN 16 +#define configUSE_16_BIT_TICKS 0 +#define configIDLE_SHOULD_YIELD 1 +#define configUSE_MUTEXES 1 +#define configUSE_RECURSIVE_MUTEXES 1 +#define configUSE_COUNTING_SEMAPHORES 1 +#define configQUEUE_REGISTRY_SIZE 4 +#define configUSE_QUEUE_SETS 0 +#define configUSE_TIME_SLICING 0 +#define configUSE_NEWLIB_REENTRANT 0 +#define configENABLE_BACKWARD_COMPATIBILITY 1 +#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 + +#define configSUPPORT_STATIC_ALLOCATION 1 +#define configSUPPORT_DYNAMIC_ALLOCATION 0 + +/* Hook function related definitions. */ +#define configUSE_IDLE_HOOK 0 +#define configUSE_TICK_HOOK 0 +#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning +#define configCHECK_FOR_STACK_OVERFLOW 2 +#define configCHECK_HANDLER_INSTALLATION 0 + +/* Run time and task stats gathering related definitions. */ +#define configGENERATE_RUN_TIME_STATS 0 +#define configRECORD_STACK_HIGH_ADDRESS 1 +#define configUSE_TRACE_FACILITY 1 // legacy trace +#define configUSE_STATS_FORMATTING_FUNCTIONS 0 + +/* Co-routine definitions. */ +#define configUSE_CO_ROUTINES 0 +#define configMAX_CO_ROUTINE_PRIORITIES 2 + +/* Software timer related definitions. */ +#define configUSE_TIMERS 1 +#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) +#define configTIMER_QUEUE_LENGTH 32 +#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE + +/* Optional functions - most linkers will remove unused functions anyway. */ +#define INCLUDE_vTaskPrioritySet 0 +#define INCLUDE_uxTaskPriorityGet 0 +#define INCLUDE_vTaskDelete 0 +#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY +#define INCLUDE_xResumeFromISR 0 +#define INCLUDE_vTaskDelayUntil 1 +#define INCLUDE_vTaskDelay 1 +#define INCLUDE_xTaskGetSchedulerState 0 +#define INCLUDE_xTaskGetCurrentTaskHandle 1 +#define INCLUDE_uxTaskGetStackHighWaterMark 0 +#define INCLUDE_xTaskGetIdleTaskHandle 0 +#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 +#define INCLUDE_pcTaskGetTaskName 0 +#define INCLUDE_eTaskGetState 0 +#define INCLUDE_xEventGroupSetBitFromISR 0 +#define INCLUDE_xTimerPendFunctionCall 0 + +/* FreeRTOS hooks to NVIC vectors */ +#define xPortPendSVHandler PendSV_Handler +#define xPortSysTickHandler SysTick_Handler +#define vPortSVCHandler SVC_Handler + +//--------------------------------------------------------------------+ +// Interrupt nesting behavior configuration. +//--------------------------------------------------------------------+ + +// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header +#define configPRIO_BITS 3 + +/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ +#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1<FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO12M */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO12M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK; +} +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO24M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO24M +outputs: +- {id: CLK_1M_clock.outFreq, value: 1 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CPU_clock.outFreq, value: 24 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_DIV_clock.outFreq, value: 48 MHz} +- {id: FRO_HF_clock.outFreq, value: 48 MHz} +- {id: MAIN_clock.outFreq, value: 48 MHz} +- {id: Slow_clock.outFreq, value: 6 MHz} +- {id: System_clock.outFreq, value: 24 MHz} +settings: +- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} +- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO24M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO24M configuration + ******************************************************************************/ +void BOARD_BootClockFRO24M(void) +{ + uint32_t coreFreq; + spc_active_mode_core_ldo_option_t ldoOption; + spc_sram_voltage_config_t sramOption; + + /* Get the CPU Core frequency */ + coreFreq = CLOCK_GetCoreSysClkFreq(); + + /* The flow of increasing voltage and frequency */ + if (coreFreq <= BOARD_BOOTCLOCKFRO24M_CORE_CLOCK) { + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO24M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 2U); /* !< Set AHBCLKDIV divider to value 2 */ + CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO24M_CORE_CLOCK; +} +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO48M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO48M +outputs: +- {id: CLK_1M_clock.outFreq, value: 1 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CPU_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_DIV_clock.outFreq, value: 48 MHz} +- {id: FRO_HF_clock.outFreq, value: 48 MHz} +- {id: MAIN_clock.outFreq, value: 48 MHz} +- {id: Slow_clock.outFreq, value: 12 MHz} +- {id: System_clock.outFreq, value: 48 MHz} +settings: +- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO48M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO48M configuration + ******************************************************************************/ +void BOARD_BootClockFRO48M(void) +{ + uint32_t coreFreq; + spc_active_mode_core_ldo_option_t ldoOption; + spc_sram_voltage_config_t sramOption; + + /* Get the CPU Core frequency */ + coreFreq = CLOCK_GetCoreSysClkFreq(); + + /* The flow of increasing voltage and frequency */ + if (coreFreq <= BOARD_BOOTCLOCKFRO48M_CORE_CLOCK) { + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO48M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P0V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ + CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO48M_CORE_CLOCK; +} +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO64M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO64M +outputs: +- {id: CLK_1M_clock.outFreq, value: 1 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CPU_clock.outFreq, value: 64 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_DIV_clock.outFreq, value: 64 MHz} +- {id: FRO_HF_clock.outFreq, value: 64 MHz} +- {id: MAIN_clock.outFreq, value: 64 MHz} +- {id: Slow_clock.outFreq, value: 16 MHz} +- {id: System_clock.outFreq, value: 64 MHz} +settings: +- {id: VDD_CORE, value: voltage_1v1} +- {id: MRCC.FROHFDIV.scale, value: '1', locked: true} +- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} +- {id: SYSCON.AHBCLKDIV.scale, value: '1', locked: true} +sources: +- {id: SCG.FIRC.outFreq, value: 64 MHz} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO64M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO64M configuration + ******************************************************************************/ +void BOARD_BootClockFRO64M(void) +{ + uint32_t coreFreq; + spc_active_mode_core_ldo_option_t ldoOption; + spc_sram_voltage_config_t sramOption; + + /* Get the CPU Core frequency */ + coreFreq = CLOCK_GetCoreSysClkFreq(); + + /* The flow of increasing voltage and frequency */ + if (coreFreq <= BOARD_BOOTCLOCKFRO64M_CORE_CLOCK) { + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P1V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFROHFClocking(64000000U); /*!< Enable FRO HF(64MHz) output */ + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO64M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P1V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ + CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO64M_CORE_CLOCK; +} +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO96M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO96M +called_from_default_init: true +outputs: +- {id: CLK_1M_clock.outFreq, value: 1 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CPU_clock.outFreq, value: 96 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_DIV_clock.outFreq, value: 96 MHz} +- {id: FRO_HF_clock.outFreq, value: 96 MHz} +- {id: MAIN_clock.outFreq, value: 96 MHz} +- {id: Slow_clock.outFreq, value: 24 MHz} +- {id: System_clock.outFreq, value: 96 MHz} +settings: +- {id: VDD_CORE, value: voltage_1v1} +- {id: CLKOUTDIV_HALT, value: Enable} +- {id: MRCC.FROHFDIV.scale, value: '1', locked: true} +- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} +- {id: SYSCON.AHBCLKDIV.scale, value: '1', locked: true} +sources: +- {id: SCG.FIRC.outFreq, value: 96 MHz} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO96M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO96M configuration + ******************************************************************************/ +void BOARD_BootClockFRO96M(void) +{ + uint32_t coreFreq; + spc_active_mode_core_ldo_option_t ldoOption; + spc_sram_voltage_config_t sramOption; + + /* Get the CPU Core frequency */ + coreFreq = CLOCK_GetCoreSysClkFreq(); + + /* The flow of increasing voltage and frequency */ + if (coreFreq <= BOARD_BOOTCLOCKFRO96M_CORE_CLOCK) { + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x2U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P1V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + } + + CLOCK_SetupFROHFClocking(96000000U); /*!< Enable FRO HF(96MHz) output */ + + CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ + + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ + + /* The flow of decreasing voltage and frequency */ + if (coreFreq > BOARD_BOOTCLOCKFRO96M_CORE_CLOCK) { + /* Configure Flash to support different voltage level and frequency */ + FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x2U)); + /* Specifies the operating voltage for the SRAM's read/write timing margin */ + sramOption.operateVoltage = kSPC_sramOperateAt1P1V; + sramOption.requestVoltageUpdate = true; + (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); + /* Set the LDO_CORE VDD regulator level */ + ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; + ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; + (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); + } + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + + /*!< Set up dividers */ + CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ + CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO96M_CORE_CLOCK; +} diff --git a/hw/bsp/mcx/boards/frdmmcxa153/clock_config.h b/hw/bsp/mcx/boards/frdmmcxa153/clock_config.h new file mode 100644 index 000000000..079d0d312 --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxa153/clock_config.h @@ -0,0 +1,170 @@ +/* + * Copyright 2023 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +#ifndef _CLOCK_CONFIG_H_ +#define _CLOCK_CONFIG_H_ + +#include "fsl_common.h" + +/******************************************************************************* + * Definitions + ******************************************************************************/ + +/******************************************************************************* + ************************ BOARD_InitBootClocks function ************************ + ******************************************************************************/ + +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes default configuration of clocks. + * + */ +void BOARD_InitBootClocks(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO12M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK 12000000U /*!< Core clock frequency: 12000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO12M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO24M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO24M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO24M_CORE_CLOCK 24000000U /*!< Core clock frequency: 24000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO24M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO24M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO48M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO48M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO48M_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO48M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO48M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO64M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO64M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO64M_CORE_CLOCK 64000000U /*!< Core clock frequency: 64000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO64M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO64M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO96M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO96M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO96M_CORE_CLOCK 96000000U /*!< Core clock frequency: 96000000Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO96M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO96M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c b/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c new file mode 100644 index 000000000..b0e6de560 --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c @@ -0,0 +1,159 @@ +/* + * Copyright 2023 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +/* clang-format off */ +/* + * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!GlobalInfo +product: Pins v14.0 +processor: MCXA153 +package_id: MCXA153VLH +mcu_data: ksdk2_0 +processor_version: 0.14.3 +pin_labels: +- {pin_num: '38', pin_signal: P3_12/LPUART2_RTS_B/CT1_MAT2/PWM0_X0, label: LED_RED, identifier: LED_RED} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** + */ +/* clang-format on */ + +#include "fsl_common.h" +#include "fsl_port.h" +#include "fsl_gpio.h" +#include "pin_mux.h" + +/* FUNCTION ************************************************************************************************************ + * + * Function Name : BOARD_InitBootPins + * Description : Calls initialization functions. + * + * END ****************************************************************************************************************/ +void BOARD_InitBootPins(void) +{ + BOARD_InitPins(); +} + +/* clang-format off */ +/* + * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +BOARD_InitPins: +- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'} +- pin_list: + - {pin_num: '38', peripheral: GPIO3, signal: 'GPIO, 12', pin_signal: P3_12/LPUART2_RTS_B/CT1_MAT2/PWM0_X0, direction: OUTPUT, gpio_init_state: 'false', slew_rate: fast, + open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** + */ +/* clang-format on */ + +/* FUNCTION ************************************************************************************************************ + * + * Function Name : BOARD_InitPins + * Description : Configures pin routing and optionally pin electrical features. + * + * END ****************************************************************************************************************/ +void BOARD_InitPins(void) +{ + RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn); + RESET_PeripheralReset(kPORT0_RST_SHIFT_RSTn); + CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u); + CLOCK_AttachClk(kFRO12M_to_LPUART0); + + /* write to PORT0: Peripheral clock is enabled */ + CLOCK_EnableClock(kCLOCK_GatePORT0); + + /* Write to GPIO3: Peripheral clock is enabled */ + CLOCK_EnableClock(kCLOCK_GateGPIO3); + /* Write to PORT3: Peripheral clock is enabled */ + CLOCK_EnableClock(kCLOCK_GatePORT3); + /* GPIO3 peripheral is released from reset */ + RESET_ReleasePeripheralReset(kGPIO3_RST_SHIFT_RSTn); + /* PORT3 peripheral is released from reset */ + RESET_ReleasePeripheralReset(kPORT3_RST_SHIFT_RSTn); + + const port_pin_config_t port3_12_pin38_config = {/* Internal pull-up/down resistor is disabled */ + kPORT_PullDisable, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Normal drive strength is configured */ + kPORT_NormalDriveStrength, + /* Pin is configured as P3_12 */ + kPORT_MuxAlt0, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT3_12 (pin 38) is configured as P3_12 */ + PORT_SetPinConfig(PORT3, 12U, &port3_12_pin38_config); + + const port_pin_config_t port0_2_pin51_config = {/* Internal pull-up resistor is enabled */ + kPORT_PullUp, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Normal drive strength is configured */ + kPORT_NormalDriveStrength, + /* Pin is configured as LPUART0_RXD */ + kPORT_MuxAlt2, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT0_2 (pin 51) is configured as LPUART0_RXD */ + PORT_SetPinConfig(PORT0, 2U, &port0_2_pin51_config); + + const port_pin_config_t port0_3_pin52_config = {/* Internal pull-up resistor is enabled */ + kPORT_PullUp, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Normal drive strength is configured */ + kPORT_NormalDriveStrength, + /* Pin is configured as LPUART0_TXD */ + kPORT_MuxAlt2, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT0_3 (pin 52) is configured as LPUART0_TXD */ + PORT_SetPinConfig(PORT0, 3U, &port0_3_pin52_config); + +} +/*********************************************************************************************************************** + * EOF + **********************************************************************************************************************/ diff --git a/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.h b/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.h new file mode 100644 index 000000000..06b6fdee9 --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.h @@ -0,0 +1,47 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +#ifndef _PIN_MUX_H_ +#define _PIN_MUX_H_ + +/*! + * @addtogroup pin_mux + * @{ + */ + +/*********************************************************************************************************************** + * API + **********************************************************************************************************************/ + +#if defined(__cplusplus) +extern "C" { +#endif + +/*! + * @brief Calls initialization functions. + * + */ +void BOARD_InitBootPins(void); + +/*! + * @brief Configures pin routing and optionally pin electrical features. + * + */ +void BOARD_InitPins(void); + +#if defined(__cplusplus) +} +#endif + +/*! + * @} + */ +#endif /* _PIN_MUX_H_ */ + +/*********************************************************************************************************************** + * EOF + **********************************************************************************************************************/ diff --git a/hw/bsp/mcx/boards/frdmmcxn947/board.cmake b/hw/bsp/mcx/boards/frdmmcxn947/board.cmake new file mode 100644 index 000000000..a08d248f5 --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxn947/board.cmake @@ -0,0 +1,24 @@ +set(MCU_VARIANT MCXN947) +set(MCU_CORE MCXN947_cm33_core0) + +set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor") +set(FAMILY_MCUS MCXN9 CACHE INTERNAL "") + +set(JLINK_DEVICE MCXN947_M33_0) +set(PYOCD_TARGET MCXN947) +set(NXPLINK_DEVICE MCXN947:MCXN947) + +set(PORT 1) + +function(update_board TARGET) + target_compile_definitions(${TARGET} PUBLIC + CPU_MCXN947VDF_cm33_core0 + BOARD_TUD_RHPORT=${PORT} + # port 0 is fullspeed, port 1 is highspeed + BOARD_TUD_MAX_SPEED=$ + ) + target_sources(${TARGET} PUBLIC + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/clock_config.c + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/pin_mux.c + ) +endfunction() diff --git a/hw/bsp/mcx/boards/frdmmcxn947/board.h b/hw/bsp/mcx/boards/frdmmcxn947/board.h new file mode 100644 index 000000000..acb73363f --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxn947/board.h @@ -0,0 +1,66 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2021, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +// LED +#define LED_GPIO GPIO0 +#define LED_CLK kCLOCK_Gpio0 +#define LED_PIN 10 // red +#define LED_STATE_ON 0 + +// WAKE button (Dummy, use unused pin +#define BUTTON_GPIO GPIO0 +#define BUTTON_CLK kCLOCK_Gpio0 +#define BUTTON_PIN 23 +#define BUTTON_STATE_ACTIVE 0 + +// UART +#define UART_DEV LPUART4 + +static inline void board_uart_init_clock(void) { + /* attach FRO 12M to FLEXCOMM4 */ + CLOCK_SetClkDiv(kCLOCK_DivFlexcom4Clk, 1u); + CLOCK_AttachClk(kFRO12M_to_FLEXCOMM4); + RESET_ClearPeripheralReset(kFC4_RST_SHIFT_RSTn); +} + +//#define UART_RX_PINMUX 0, 24, IOCON_PIO_DIG_FUNC1_EN +//#define UART_TX_PINMUX 0, 25, IOCON_PIO_DIG_FUNC1_EN + +// XTAL +#define XTAL0_CLK_HZ (24 * 1000 * 1000U) + +#ifdef __cplusplus + } +#endif + +#endif diff --git a/hw/bsp/mcx/boards/frdmmcxn947/board.mk b/hw/bsp/mcx/boards/frdmmcxn947/board.mk new file mode 100644 index 000000000..d90780996 --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxn947/board.mk @@ -0,0 +1,14 @@ +MCU_VARIANT = MCXN947 +MCU_CORE = MCXN947_cm33_core0 +PORT ?= 1 + +CPU_CORE ?= cortex-m33 +CFLAGS += \ + -DCPU_MCXN947VDF_cm33_core0 \ + -DCFG_TUSB_MCU=OPT_MCU_MCXN9 \ + +JLINK_DEVICE = MCXN947_M33_0 +PYOCD_TARGET = MCXN947 + +# flash using pyocd +flash: flash-jlink diff --git a/hw/bsp/mcx/boards/frdmmcxn947/clock_config.c b/hw/bsp/mcx/boards/frdmmcxn947/clock_config.c new file mode 100644 index 000000000..37d2b4dfc --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxn947/clock_config.c @@ -0,0 +1,338 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ +/* + * How to setup clock using clock driver functions: + * + * 1. Setup clock sources. + * + * 2. Set up wait states of the flash. + * + * 3. Set up all dividers. + * + * 4. Set up all selectors to provide selected clocks. + * + */ + +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!GlobalInfo +product: Clocks v10.0 +processor: MCXN947 +package_id: MCXN947VDF +mcu_data: ksdk2_0 +processor_version: 0.12.3 +board: MCX-N9XX-EVK + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +#include "clock_config.h" +#include "fsl_clock.h" + +/******************************************************************************* + * Definitions + ******************************************************************************/ + +/******************************************************************************* + * Variables + ******************************************************************************/ +/* System clock frequency. */ +// extern uint32_t SystemCoreClock; + +/******************************************************************************* + ************************ BOARD_InitBootClocks function ************************ + ******************************************************************************/ +void BOARD_InitBootClocks(void) +{ + BOARD_BootClockPLL150M(); +} + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO12M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO12M +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: MAIN_clock.outFreq, value: 12 MHz} +- {id: Slow_clock.outFreq, value: 3 MHz} +- {id: System_clock.outFreq, value: 12 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: SCGMode, value: SIRC} +- {id: SCG.SCSSEL.sel, value: SCG.SIRC} +- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +void BOARD_BootClockFRO12M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO12M */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK; +} + +/******************************************************************************* + ******************* Configuration BOARD_BootClockFROHF48M ********************* + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFROHF48M +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_clock.outFreq, value: 48 MHz} +- {id: MAIN_clock.outFreq, value: 48 MHz} +- {id: Slow_clock.outFreq, value: 12 MHz} +- {id: System_clock.outFreq, value: 48 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFROHF48M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFROHF48M configuration + ******************************************************************************/ +void BOARD_BootClockFROHF48M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK; +} + +/******************************************************************************* + ******************* Configuration BOARD_BootClockFROHF144M ******************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFROHF144M +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_clock.outFreq, value: 144 MHz} +- {id: MAIN_clock.outFreq, value: 144 MHz} +- {id: Slow_clock.outFreq, value: 18 MHz} +- {id: System_clock.outFreq, value: 72 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true} +- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} +sources: +- {id: SCG.FIRC.outFreq, value: 144 MHz} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFROHF144M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFROHF144M configuration + ******************************************************************************/ +void BOARD_BootClockFROHF144M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + CLOCK_SetupFROHFClocking(144000000U); /*!< Enable FRO HF(144MHz) output */ + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 2U); /*!< Set AHBCLKDIV divider to value 2 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK; +} + +/******************************************************************************* + ******************** Configuration BOARD_BootClockPLL150M ********************* + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockPLL150M +called_from_default_init: true +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_clock.outFreq, value: 48 MHz} +- {id: MAIN_clock.outFreq, value: 150 MHz} +- {id: PLL0_CLK_clock.outFreq, value: 150 MHz} +- {id: Slow_clock.outFreq, value: 37.5 MHz} +- {id: System_clock.outFreq, value: 150 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: PLL0_Mode, value: Normal} +- {id: RunPowerMode, value: OD} +- {id: SCGMode, value: PLL0} +- {id: SCG.PLL0M_MULT.scale, value: '50', locked: true} +- {id: SCG.PLL0SRCSEL.sel, value: SCG.FIRC_48M} +- {id: SCG.PLL0_NDIV.scale, value: '8', locked: true} +- {id: SCG.SCSSEL.sel, value: SCG.PLL0_CLK} +- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockPLL150M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockPLL150M configuration + ******************************************************************************/ +void BOARD_BootClockPLL150M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ + + /*!< Set up PLL0 */ + const pll_setup_t pll0Setup = { + .pllctrl = SCG_APLLCTRL_SOURCE(1U) | SCG_APLLCTRL_SELI(27U) | SCG_APLLCTRL_SELP(13U), + .pllndiv = SCG_APLLNDIV_NDIV(8U), + .pllpdiv = SCG_APLLPDIV_PDIV(1U), + .pllmdiv = SCG_APLLMDIV_MDIV(50U), + .pllRate = 150000000U + }; + CLOCK_SetPLL0Freq(&pll0Setup); /*!< Configure PLL0 to the desired values */ + CLOCK_SetPll0MonitorMode(kSCG_Pll0MonitorDisable); /* Pll0 Monitor is disabled */ + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kPLL0_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL0 */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKPLL150M_CORE_CLOCK; +} + +/******************************************************************************* + ******************** Configuration BOARD_BootClockPLL100M ********************* + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockPLL100M +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CLK_IN_clock.outFreq, value: 24 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: MAIN_clock.outFreq, value: 100 MHz} +- {id: PLL1_CLK_clock.outFreq, value: 100 MHz} +- {id: Slow_clock.outFreq, value: 25 MHz} +- {id: System_clock.outFreq, value: 100 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: PLL1_Mode, value: Normal} +- {id: SCGMode, value: PLL1} +- {id: SCG.PLL1M_MULT.scale, value: '100', locked: true} +- {id: SCG.PLL1_NDIV.scale, value: '6', locked: true} +- {id: SCG.PLL1_PDIV.scale, value: '4', locked: true} +- {id: SCG.SCSSEL.sel, value: SCG.PLL1_CLK} +- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} +- {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} +sources: +- {id: SCG.SOSC.outFreq, value: 24 MHz, enabled: true} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockPLL100M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockPLL100M configuration + ******************************************************************************/ +void BOARD_BootClockPLL100M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + CLOCK_SetupExtClocking(24000000U); + CLOCK_SetSysOscMonitorMode(kSCG_SysOscMonitorDisable); /* System OSC Clock Monitor is disabled */ + + /*!< Set up PLL1 */ + const pll_setup_t pll1Setup = { + .pllctrl = SCG_SPLLCTRL_SOURCE(0U) | SCG_SPLLCTRL_SELI(53U) | SCG_SPLLCTRL_SELP(26U), + .pllndiv = SCG_SPLLNDIV_NDIV(6U), + .pllpdiv = SCG_SPLLPDIV_PDIV(2U), + .pllmdiv = SCG_SPLLMDIV_MDIV(100U), + .pllRate = 100000000U + }; + CLOCK_SetPLL1Freq(&pll1Setup); /*!< Configure PLL1 to the desired values */ + CLOCK_SetPll1MonitorMode(kSCG_Pll1MonitorDisable); /* Pll1 Monitor is disabled */ + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kPLL1_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL1 */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKPLL100M_CORE_CLOCK; +} diff --git a/hw/bsp/mcx/boards/frdmmcxn947/clock_config.h b/hw/bsp/mcx/boards/frdmmcxn947/clock_config.h new file mode 100644 index 000000000..c238a0423 --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxn947/clock_config.h @@ -0,0 +1,177 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +#ifndef _CLOCK_CONFIG_H_ +#define _CLOCK_CONFIG_H_ + +#include "fsl_common.h" + +/******************************************************************************* + * Definitions + ******************************************************************************/ +#define BOARD_XTAL0_CLK_HZ 24000000U /*!< Board xtal frequency in Hz */ +#define BOARD_XTAL32K_CLK_HZ 32768U /*!< Board xtal32K frequency in Hz */ + +/******************************************************************************* + ************************ BOARD_InitBootClocks function ************************ + ******************************************************************************/ + +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes default configuration of clocks. + * + */ +void BOARD_InitBootClocks(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO12M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK 12000000U /*!< Core clock frequency: 12000000Hz */ +#define BOARD_BOOTCLOCKFRO12M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO12M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************* Configuration BOARD_BootClockFROHF48M ********************* + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFROHF48M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ +#define BOARD_BOOTCLOCKFROHF48M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFROHF48M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFROHF48M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************* Configuration BOARD_BootClockFROHF144M ******************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFROHF144M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK 144000000U /*!< Core clock frequency: 144000000Hz */ +#define BOARD_BOOTCLOCKFROHF144M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFROHF144M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFROHF144M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockPLL150M ********************* + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockPLL150M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKPLL150M_CORE_CLOCK 150000000U /*!< Core clock frequency: 150000000Hz */ +#define BOARD_BOOTCLOCKPLL150M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockPLL150M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockPLL150M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockPLL100M ********************* + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockPLL100M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKPLL100M_CORE_CLOCK 100000000U /*!< Core clock frequency: 100000000Hz */ +#define BOARD_BOOTCLOCKPLL100M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockPLL100M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockPLL100M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/mcx/boards/frdmmcxn947/pin_mux.c b/hw/bsp/mcx/boards/frdmmcxn947/pin_mux.c new file mode 100644 index 000000000..c33790ac5 --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxn947/pin_mux.c @@ -0,0 +1,143 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +/* clang-format off */ +/* + * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!GlobalInfo +product: Pins v12.0 +processor: MCXN947 +package_id: MCXN947VDF +mcu_data: ksdk2_0 +processor_version: 0.12.3 + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** + */ +/* clang-format on */ + +#include "fsl_common.h" +#include "fsl_port.h" +#include "pin_mux.h" + +/* FUNCTION ************************************************************************************************************ + * + * Function Name : BOARD_InitBootPins + * Description : Calls initialization functions. + * + * END ****************************************************************************************************************/ +void BOARD_InitBootPins(void) +{ + BOARD_InitPins(); +} + +/* clang-format off */ +/* + * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +BOARD_InitPins: +- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'} +- pin_list: + - {pin_num: A1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P0, pin_signal: PIO1_8/WUU0_IN10/LPTMR1_ALT3/TRACE_DATA0/FC4_P0/FC5_P4/CT_INP8/SCT0_OUT2/FLEXIO0_D16/PLU_OUT0/ENET0_TXD2/I3C1_SDA/TSI0_CH17/ADC1_A8, + slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, pull_value: low, input_buffer: enable, + invert_input: normal} + - {pin_num: B1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P1, pin_signal: PIO1_9/TRACE_DATA1/FC4_P1/FC5_P5/CT_INP9/SCT0_OUT3/FLEXIO0_D17/PLU_OUT1/ENET0_TXD3/I3C1_SCL/TSI0_CH18/ADC1_A9, + slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, input_buffer: enable, invert_input: normal} + - {pin_num: B7, peripheral: GPIO0, signal: 'GPIO, 23', pin_signal: PIO0_23/WUU0_IN5/EWM0_OUT_b/FC1_P3/CT_INP3/FLEXIO0_D7/ADC0_A15/CMP2_IN2, direction: INPUT, slew_rate: fast, + open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** + */ +/* clang-format on */ + +/* FUNCTION ************************************************************************************************************ + * + * Function Name : BOARD_InitPins + * Description : Configures pin routing and optionally pin electrical features. + * + * END ****************************************************************************************************************/ +void BOARD_InitPins(void) +{ + /* Enables the clock for PORT0: Enables clock */ + CLOCK_EnableClock(kCLOCK_Port0); + + /* Enables the clock for PORT1: Enables clock */ + CLOCK_EnableClock(kCLOCK_Port1); + + + const port_pin_config_t port1_8_pinA1_config = {/* Internal pull-up/down resistor is disabled */ + kPORT_PullDisable, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Pin is configured as FC4_P0 */ + kPORT_MuxAlt2, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT1_8 (pin A1) is configured as FC4_P0 */ + PORT_SetPinConfig(PORT1, 8U, &port1_8_pinA1_config); + + const port_pin_config_t port1_9_pinB1_config = {/* Internal pull-up/down resistor is disabled */ + kPORT_PullDisable, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Pin is configured as FC4_P1 */ + kPORT_MuxAlt2, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT1_9 (pin B1) is configured as FC4_P1 */ + PORT_SetPinConfig(PORT1, 9U, &port1_9_pinB1_config); + + const port_pin_config_t SW2 = {/* Internal pull-up/down resistor is disabled */ + kPORT_PullDisable, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Pin is configured as PIO0_23 */ + kPORT_MuxAlt0, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT0_23 (pin B7) is configured as PIO0_23 */ + PORT_SetPinConfig(PORT0, 23U, &SW2); +} +/*********************************************************************************************************************** + * EOF + **********************************************************************************************************************/ diff --git a/hw/bsp/mcx/boards/frdmmcxn947/pin_mux.h b/hw/bsp/mcx/boards/frdmmcxn947/pin_mux.h new file mode 100644 index 000000000..40968c275 --- /dev/null +++ b/hw/bsp/mcx/boards/frdmmcxn947/pin_mux.h @@ -0,0 +1,51 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +#ifndef _PIN_MUX_H_ +#define _PIN_MUX_H_ + +/*! + * @addtogroup pin_mux + * @{ + */ + +/*********************************************************************************************************************** + * API + **********************************************************************************************************************/ + +#if defined(__cplusplus) +extern "C" { +#endif + +/*! + * @brief Calls initialization functions. + * + */ +void BOARD_InitBootPins(void); + +/*! + * @brief Configures pin routing and optionally pin electrical features. + * + */ +void BOARD_InitPins(void); + +#if defined(__cplusplus) +} +#endif + +/*! + * @} + */ +#endif /* _PIN_MUX_H_ */ + +/*********************************************************************************************************************** + * EOF + **********************************************************************************************************************/ diff --git a/hw/bsp/mcx/boards/mcxn947brk/board.cmake b/hw/bsp/mcx/boards/mcxn947brk/board.cmake new file mode 100644 index 000000000..a08d248f5 --- /dev/null +++ b/hw/bsp/mcx/boards/mcxn947brk/board.cmake @@ -0,0 +1,24 @@ +set(MCU_VARIANT MCXN947) +set(MCU_CORE MCXN947_cm33_core0) + +set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor") +set(FAMILY_MCUS MCXN9 CACHE INTERNAL "") + +set(JLINK_DEVICE MCXN947_M33_0) +set(PYOCD_TARGET MCXN947) +set(NXPLINK_DEVICE MCXN947:MCXN947) + +set(PORT 1) + +function(update_board TARGET) + target_compile_definitions(${TARGET} PUBLIC + CPU_MCXN947VDF_cm33_core0 + BOARD_TUD_RHPORT=${PORT} + # port 0 is fullspeed, port 1 is highspeed + BOARD_TUD_MAX_SPEED=$ + ) + target_sources(${TARGET} PUBLIC + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/clock_config.c + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/pin_mux.c + ) +endfunction() diff --git a/hw/bsp/mcx/boards/mcxn947brk/board.h b/hw/bsp/mcx/boards/mcxn947brk/board.h new file mode 100644 index 000000000..eae98bfa7 --- /dev/null +++ b/hw/bsp/mcx/boards/mcxn947brk/board.h @@ -0,0 +1,66 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2021, Ha Thach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus + extern "C" { +#endif + +// LED +#define LED_GPIO GPIO3 +#define LED_CLK kCLOCK_Gpio3 +#define LED_PIN 4 // red +#define LED_STATE_ON 0 + +// WAKE button (Dummy, use unused pin +#define BUTTON_GPIO GPIO0 +#define BUTTON_CLK kCLOCK_Gpio0 +#define BUTTON_PIN 6 +#define BUTTON_STATE_ACTIVE 0 + +// UART +#define UART_DEV LPUART4 + +static inline void board_uart_init_clock(void) { + /* attach FRO 12M to FLEXCOMM4 */ + CLOCK_SetClkDiv(kCLOCK_DivFlexcom4Clk, 1u); + CLOCK_AttachClk(kFRO12M_to_FLEXCOMM4); + RESET_ClearPeripheralReset(kFC4_RST_SHIFT_RSTn); +} + +//#define UART_RX_PINMUX 0, 24, IOCON_PIO_DIG_FUNC1_EN +//#define UART_TX_PINMUX 0, 25, IOCON_PIO_DIG_FUNC1_EN + +// XTAL +#define XTAL0_CLK_HZ (24 * 1000 * 1000U) + +#ifdef __cplusplus + } +#endif + +#endif diff --git a/hw/bsp/mcx/boards/mcxn947brk/board.mk b/hw/bsp/mcx/boards/mcxn947brk/board.mk new file mode 100644 index 000000000..d90780996 --- /dev/null +++ b/hw/bsp/mcx/boards/mcxn947brk/board.mk @@ -0,0 +1,14 @@ +MCU_VARIANT = MCXN947 +MCU_CORE = MCXN947_cm33_core0 +PORT ?= 1 + +CPU_CORE ?= cortex-m33 +CFLAGS += \ + -DCPU_MCXN947VDF_cm33_core0 \ + -DCFG_TUSB_MCU=OPT_MCU_MCXN9 \ + +JLINK_DEVICE = MCXN947_M33_0 +PYOCD_TARGET = MCXN947 + +# flash using pyocd +flash: flash-jlink diff --git a/hw/bsp/mcx/boards/mcxn947brk/clock_config.c b/hw/bsp/mcx/boards/mcxn947brk/clock_config.c new file mode 100644 index 000000000..37d2b4dfc --- /dev/null +++ b/hw/bsp/mcx/boards/mcxn947brk/clock_config.c @@ -0,0 +1,338 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ +/* + * How to setup clock using clock driver functions: + * + * 1. Setup clock sources. + * + * 2. Set up wait states of the flash. + * + * 3. Set up all dividers. + * + * 4. Set up all selectors to provide selected clocks. + * + */ + +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!GlobalInfo +product: Clocks v10.0 +processor: MCXN947 +package_id: MCXN947VDF +mcu_data: ksdk2_0 +processor_version: 0.12.3 +board: MCX-N9XX-EVK + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +#include "clock_config.h" +#include "fsl_clock.h" + +/******************************************************************************* + * Definitions + ******************************************************************************/ + +/******************************************************************************* + * Variables + ******************************************************************************/ +/* System clock frequency. */ +// extern uint32_t SystemCoreClock; + +/******************************************************************************* + ************************ BOARD_InitBootClocks function ************************ + ******************************************************************************/ +void BOARD_InitBootClocks(void) +{ + BOARD_BootClockPLL150M(); +} + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO12M ********************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFRO12M +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: MAIN_clock.outFreq, value: 12 MHz} +- {id: Slow_clock.outFreq, value: 3 MHz} +- {id: System_clock.outFreq, value: 12 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: SCGMode, value: SIRC} +- {id: SCG.SCSSEL.sel, value: SCG.SIRC} +- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +void BOARD_BootClockFRO12M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO12M */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK; +} + +/******************************************************************************* + ******************* Configuration BOARD_BootClockFROHF48M ********************* + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFROHF48M +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_clock.outFreq, value: 48 MHz} +- {id: MAIN_clock.outFreq, value: 48 MHz} +- {id: Slow_clock.outFreq, value: 12 MHz} +- {id: System_clock.outFreq, value: 48 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFROHF48M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFROHF48M configuration + ******************************************************************************/ +void BOARD_BootClockFROHF48M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK; +} + +/******************************************************************************* + ******************* Configuration BOARD_BootClockFROHF144M ******************** + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockFROHF144M +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_clock.outFreq, value: 144 MHz} +- {id: MAIN_clock.outFreq, value: 144 MHz} +- {id: Slow_clock.outFreq, value: 18 MHz} +- {id: System_clock.outFreq, value: 72 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true} +- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} +sources: +- {id: SCG.FIRC.outFreq, value: 144 MHz} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockFROHF144M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockFROHF144M configuration + ******************************************************************************/ +void BOARD_BootClockFROHF144M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + CLOCK_SetupFROHFClocking(144000000U); /*!< Enable FRO HF(144MHz) output */ + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 2U); /*!< Set AHBCLKDIV divider to value 2 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK; +} + +/******************************************************************************* + ******************** Configuration BOARD_BootClockPLL150M ********************* + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockPLL150M +called_from_default_init: true +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: FRO_HF_clock.outFreq, value: 48 MHz} +- {id: MAIN_clock.outFreq, value: 150 MHz} +- {id: PLL0_CLK_clock.outFreq, value: 150 MHz} +- {id: Slow_clock.outFreq, value: 37.5 MHz} +- {id: System_clock.outFreq, value: 150 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: PLL0_Mode, value: Normal} +- {id: RunPowerMode, value: OD} +- {id: SCGMode, value: PLL0} +- {id: SCG.PLL0M_MULT.scale, value: '50', locked: true} +- {id: SCG.PLL0SRCSEL.sel, value: SCG.FIRC_48M} +- {id: SCG.PLL0_NDIV.scale, value: '8', locked: true} +- {id: SCG.SCSSEL.sel, value: SCG.PLL0_CLK} +- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockPLL150M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockPLL150M configuration + ******************************************************************************/ +void BOARD_BootClockPLL150M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ + + /*!< Set up PLL0 */ + const pll_setup_t pll0Setup = { + .pllctrl = SCG_APLLCTRL_SOURCE(1U) | SCG_APLLCTRL_SELI(27U) | SCG_APLLCTRL_SELP(13U), + .pllndiv = SCG_APLLNDIV_NDIV(8U), + .pllpdiv = SCG_APLLPDIV_PDIV(1U), + .pllmdiv = SCG_APLLMDIV_MDIV(50U), + .pllRate = 150000000U + }; + CLOCK_SetPLL0Freq(&pll0Setup); /*!< Configure PLL0 to the desired values */ + CLOCK_SetPll0MonitorMode(kSCG_Pll0MonitorDisable); /* Pll0 Monitor is disabled */ + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kPLL0_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL0 */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKPLL150M_CORE_CLOCK; +} + +/******************************************************************************* + ******************** Configuration BOARD_BootClockPLL100M ********************* + ******************************************************************************/ +/* clang-format off */ +/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!Configuration +name: BOARD_BootClockPLL100M +outputs: +- {id: CLK_144M_clock.outFreq, value: 144 MHz} +- {id: CLK_48M_clock.outFreq, value: 48 MHz} +- {id: CLK_IN_clock.outFreq, value: 24 MHz} +- {id: FRO_12M_clock.outFreq, value: 12 MHz} +- {id: MAIN_clock.outFreq, value: 100 MHz} +- {id: PLL1_CLK_clock.outFreq, value: 100 MHz} +- {id: Slow_clock.outFreq, value: 25 MHz} +- {id: System_clock.outFreq, value: 100 MHz} +- {id: gdet_clock.outFreq, value: 48 MHz} +- {id: trng_clock.outFreq, value: 48 MHz} +settings: +- {id: PLL1_Mode, value: Normal} +- {id: SCGMode, value: PLL1} +- {id: SCG.PLL1M_MULT.scale, value: '100', locked: true} +- {id: SCG.PLL1_NDIV.scale, value: '6', locked: true} +- {id: SCG.PLL1_PDIV.scale, value: '4', locked: true} +- {id: SCG.SCSSEL.sel, value: SCG.PLL1_CLK} +- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} +- {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled} +- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} +- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} +sources: +- {id: SCG.SOSC.outFreq, value: 24 MHz, enabled: true} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ +/* clang-format on */ + +/******************************************************************************* + * Variables for BOARD_BootClockPLL100M configuration + ******************************************************************************/ +/******************************************************************************* + * Code for BOARD_BootClockPLL100M configuration + ******************************************************************************/ +void BOARD_BootClockPLL100M(void) +{ + /*!< Enable SCG clock */ + CLOCK_EnableClock(kCLOCK_Scg); + + CLOCK_SetupExtClocking(24000000U); + CLOCK_SetSysOscMonitorMode(kSCG_SysOscMonitorDisable); /* System OSC Clock Monitor is disabled */ + + /*!< Set up PLL1 */ + const pll_setup_t pll1Setup = { + .pllctrl = SCG_SPLLCTRL_SOURCE(0U) | SCG_SPLLCTRL_SELI(53U) | SCG_SPLLCTRL_SELP(26U), + .pllndiv = SCG_SPLLNDIV_NDIV(6U), + .pllpdiv = SCG_SPLLPDIV_PDIV(2U), + .pllmdiv = SCG_SPLLMDIV_MDIV(100U), + .pllRate = 100000000U + }; + CLOCK_SetPLL1Freq(&pll1Setup); /*!< Configure PLL1 to the desired values */ + CLOCK_SetPll1MonitorMode(kSCG_Pll1MonitorDisable); /* Pll1 Monitor is disabled */ + + /*!< Set up clock selectors - Attach clocks to the peripheries */ + CLOCK_AttachClk(kPLL1_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL1 */ + + /*!< Set up dividers */ + CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ + + /* Set SystemCoreClock variable */ + SystemCoreClock = BOARD_BOOTCLOCKPLL100M_CORE_CLOCK; +} diff --git a/hw/bsp/mcx/boards/mcxn947brk/clock_config.h b/hw/bsp/mcx/boards/mcxn947brk/clock_config.h new file mode 100644 index 000000000..c238a0423 --- /dev/null +++ b/hw/bsp/mcx/boards/mcxn947brk/clock_config.h @@ -0,0 +1,177 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ + +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +#ifndef _CLOCK_CONFIG_H_ +#define _CLOCK_CONFIG_H_ + +#include "fsl_common.h" + +/******************************************************************************* + * Definitions + ******************************************************************************/ +#define BOARD_XTAL0_CLK_HZ 24000000U /*!< Board xtal frequency in Hz */ +#define BOARD_XTAL32K_CLK_HZ 32768U /*!< Board xtal32K frequency in Hz */ + +/******************************************************************************* + ************************ BOARD_InitBootClocks function ************************ + ******************************************************************************/ + +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes default configuration of clocks. + * + */ +void BOARD_InitBootClocks(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockFRO12M ********************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK 12000000U /*!< Core clock frequency: 12000000Hz */ +#define BOARD_BOOTCLOCKFRO12M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFRO12M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFRO12M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************* Configuration BOARD_BootClockFROHF48M ********************* + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFROHF48M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ +#define BOARD_BOOTCLOCKFROHF48M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFROHF48M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFROHF48M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************* Configuration BOARD_BootClockFROHF144M ******************** + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockFROHF144M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK 144000000U /*!< Core clock frequency: 144000000Hz */ +#define BOARD_BOOTCLOCKFROHF144M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockFROHF144M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockFROHF144M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockPLL150M ********************* + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockPLL150M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKPLL150M_CORE_CLOCK 150000000U /*!< Core clock frequency: 150000000Hz */ +#define BOARD_BOOTCLOCKPLL150M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockPLL150M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockPLL150M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +/******************************************************************************* + ******************** Configuration BOARD_BootClockPLL100M ********************* + ******************************************************************************/ +/******************************************************************************* + * Definitions for BOARD_BootClockPLL100M configuration + ******************************************************************************/ +#define BOARD_BOOTCLOCKPLL100M_CORE_CLOCK 100000000U /*!< Core clock frequency: 100000000Hz */ +#define BOARD_BOOTCLOCKPLL100M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ + + +/******************************************************************************* + * API for BOARD_BootClockPLL100M configuration + ******************************************************************************/ +#if defined(__cplusplus) +extern "C" { +#endif /* __cplusplus*/ + +/*! + * @brief This function executes configuration of clocks. + * + */ +void BOARD_BootClockPLL100M(void); + +#if defined(__cplusplus) +} +#endif /* __cplusplus*/ + +#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/mcx/boards/mcxn947brk/pin_mux.c b/hw/bsp/mcx/boards/mcxn947brk/pin_mux.c new file mode 100644 index 000000000..acc2f3e45 --- /dev/null +++ b/hw/bsp/mcx/boards/mcxn947brk/pin_mux.c @@ -0,0 +1,141 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +/* clang-format off */ +/* + * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +!!GlobalInfo +product: Pins v12.0 +processor: MCXN947 +package_id: MCXN947VDF +mcu_data: ksdk2_0 +processor_version: 0.12.3 + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** + */ +/* clang-format on */ + +#include "fsl_common.h" +#include "fsl_port.h" +#include "pin_mux.h" + +/* FUNCTION ************************************************************************************************************ + * + * Function Name : BOARD_InitBootPins + * Description : Calls initialization functions. + * + * END ****************************************************************************************************************/ +void BOARD_InitBootPins(void) +{ + BOARD_InitPins(); +} + +/* clang-format off */ +/* + * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* +BOARD_InitPins: +- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'} +- pin_list: + - {pin_num: A1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P0, pin_signal: PIO1_8/WUU0_IN10/LPTMR1_ALT3/TRACE_DATA0/FC4_P0/FC5_P4/CT_INP8/SCT0_OUT2/FLEXIO0_D16/PLU_OUT0/ENET0_TXD2/I3C1_SDA/TSI0_CH17/ADC1_A8, + slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, pull_value: low, input_buffer: enable, + invert_input: normal} + - {pin_num: B1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P1, pin_signal: PIO1_9/TRACE_DATA1/FC4_P1/FC5_P5/CT_INP9/SCT0_OUT3/FLEXIO0_D17/PLU_OUT1/ENET0_TXD3/I3C1_SCL/TSI0_CH18/ADC1_A9, + slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, input_buffer: enable, invert_input: normal} + - {pin_num: F14, peripheral: GPIO3, signal: 'GPIO, 4', pin_signal: PIO3_4/FC7_P2/CT_INP18/PWM0_X2/FLEXIO0_D12/SIM1_CLK, slew_rate: fast, open_drain: disable, drive_strength: low, + pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal} + * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** + */ +/* clang-format on */ + +/* FUNCTION ************************************************************************************************************ + * + * Function Name : BOARD_InitPins + * Description : Configures pin routing and optionally pin electrical features. + * + * END ****************************************************************************************************************/ +void BOARD_InitPins(void) +{ + /* Enables the clock for PORT1: Enables clock */ + CLOCK_EnableClock(kCLOCK_Port1); + /* Enables the clock for PORT3: Enables clock */ + CLOCK_EnableClock(kCLOCK_Port3); + + const port_pin_config_t port1_8_pinA1_config = {/* Internal pull-up/down resistor is disabled */ + kPORT_PullDisable, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Pin is configured as FC4_P0 */ + kPORT_MuxAlt2, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT1_8 (pin A1) is configured as FC4_P0 */ + PORT_SetPinConfig(PORT1, 8U, &port1_8_pinA1_config); + + const port_pin_config_t port1_9_pinB1_config = {/* Internal pull-up/down resistor is disabled */ + kPORT_PullDisable, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Pin is configured as FC4_P1 */ + kPORT_MuxAlt2, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT1_9 (pin B1) is configured as FC4_P1 */ + PORT_SetPinConfig(PORT1, 9U, &port1_9_pinB1_config); + + const port_pin_config_t port3_4_pinF14_config = {/* Internal pull-up/down resistor is disabled */ + kPORT_PullDisable, + /* Low internal pull resistor value is selected. */ + kPORT_LowPullResistor, + /* Fast slew rate is configured */ + kPORT_FastSlewRate, + /* Passive input filter is disabled */ + kPORT_PassiveFilterDisable, + /* Open drain output is disabled */ + kPORT_OpenDrainDisable, + /* Low drive strength is configured */ + kPORT_LowDriveStrength, + /* Pin is configured as PIO3_4 */ + kPORT_MuxAlt0, + /* Digital input enabled */ + kPORT_InputBufferEnable, + /* Digital input is not inverted */ + kPORT_InputNormal, + /* Pin Control Register fields [15:0] are not locked */ + kPORT_UnlockRegister}; + /* PORT3_4 (pin F14) is configured as PIO3_4 */ + PORT_SetPinConfig(PORT3, 4U, &port3_4_pinF14_config); +} +/*********************************************************************************************************************** + * EOF + **********************************************************************************************************************/ diff --git a/hw/bsp/mcx/boards/mcxn947brk/pin_mux.h b/hw/bsp/mcx/boards/mcxn947brk/pin_mux.h new file mode 100644 index 000000000..40968c275 --- /dev/null +++ b/hw/bsp/mcx/boards/mcxn947brk/pin_mux.h @@ -0,0 +1,51 @@ +/* + * Copyright 2022 NXP + * All rights reserved. + * + * SPDX-License-Identifier: BSD-3-Clause + */ +/*********************************************************************************************************************** + * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file + * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. + **********************************************************************************************************************/ + +#ifndef _PIN_MUX_H_ +#define _PIN_MUX_H_ + +/*! + * @addtogroup pin_mux + * @{ + */ + +/*********************************************************************************************************************** + * API + **********************************************************************************************************************/ + +#if defined(__cplusplus) +extern "C" { +#endif + +/*! + * @brief Calls initialization functions. + * + */ +void BOARD_InitBootPins(void); + +/*! + * @brief Configures pin routing and optionally pin electrical features. + * + */ +void BOARD_InitPins(void); + +#if defined(__cplusplus) +} +#endif + +/*! + * @} + */ +#endif /* _PIN_MUX_H_ */ + +/*********************************************************************************************************************** + * EOF + **********************************************************************************************************************/ diff --git a/hw/bsp/mcx/debug.jlinkscript b/hw/bsp/mcx/debug.jlinkscript new file mode 100644 index 000000000..fd8bcffef --- /dev/null +++ b/hw/bsp/mcx/debug.jlinkscript @@ -0,0 +1,5 @@ +int SetupTarget(void) { + JLINK_ExecCommand("SetRTTSearchRanges 0x20000000 0x40000"); + + return 0; +} diff --git a/hw/bsp/mcx/family.c b/hw/bsp/mcx/family.c new file mode 100644 index 000000000..74b84773d --- /dev/null +++ b/hw/bsp/mcx/family.c @@ -0,0 +1,267 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2018, hathach (tinyusb.org) + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#include "bsp/board_api.h" +#include "fsl_device_registers.h" +#include "fsl_gpio.h" +#include "fsl_lpuart.h" +#include "board.h" + +#include "pin_mux.h" +#include "clock_config.h" + +#ifdef BOARD_TUD_RHPORT + #define PORT_SUPPORT_DEVICE(_n) (BOARD_TUD_RHPORT == _n) +#else + #define PORT_SUPPORT_DEVICE(_n) 0 +#endif + +#ifdef BOARD_TUH_RHPORT + #define PORT_SUPPORT_HOST(_n) (BOARD_TUH_RHPORT == _n) +#else + #define PORT_SUPPORT_HOST(_n) 0 +#endif + +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + +//--------------------------------------------------------------------+ +// Forward USB interrupt events to TinyUSB IRQ Handler +//--------------------------------------------------------------------+ + +#if CFG_TUSB_MCU == OPT_MCU_MCXN9 +void USB0_FS_IRQHandler(void) +{ + tud_int_handler(0); +} + +void USB1_HS_IRQHandler(void) +{ + tud_int_handler(1); +} + +#elif CFG_TUSB_MCU == OPT_MCU_MCXA15 +void USB0_IRQHandler(void) +{ + tud_int_handler(0); +} +#endif + + +void board_init(void) +{ + BOARD_InitPins(); + BOARD_InitBootClocks(); + CLOCK_SetupExtClocking(XTAL0_CLK_HZ); + + // 1ms tick timer + SysTick_Config(SystemCoreClock / 1000); + +#if CFG_TUSB_OS == OPT_OS_FREERTOS + // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) + NVIC_SetPriority(USB1_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); +#endif + + // LED + CLOCK_EnableClock(LED_CLK); + gpio_pin_config_t led_config = { + kGPIO_DigitalOutput, + 0, + }; + GPIO_PinInit(LED_GPIO,LED_PIN, &led_config); + board_led_write(0); + +#ifdef NEOPIXEL_PIN + // Neopixel + static uint32_t pixelData[NEOPIXEL_NUMBER]; + IOCON_PinMuxSet(IOCON, NEOPIXEL_PORT, NEOPIXEL_PIN, IOCON_PIO_DIG_FUNC4_EN); + + sctpix_init(NEOPIXEL_TYPE); + sctpix_addCh(NEOPIXEL_CH, pixelData, NEOPIXEL_NUMBER); + sctpix_setPixel(NEOPIXEL_CH, 0, 0x100010); + sctpix_setPixel(NEOPIXEL_CH, 1, 0x100010); + sctpix_show(); +#endif + + // Button +#ifdef BUTTON_GPIO + CLOCK_EnableClock(BUTTON_CLK); + gpio_pin_config_t const button_config = { kGPIO_DigitalInput, 0}; + GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); +#endif + +#ifdef UART_DEV + // UART +// IOCON_PinMuxSet(IOCON, UART_RX_PINMUX); +// IOCON_PinMuxSet(IOCON, UART_TX_PINMUX); + + // Enable UART when debug log is on + board_uart_init_clock(); + + lpuart_config_t uart_config; + LPUART_GetDefaultConfig(&uart_config); + uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE; + uart_config.enableTx = true; + uart_config.enableRx = true; + LPUART_Init(UART_DEV, &uart_config, 12000000u); +#endif + + // USB VBUS + /* PORT0 PIN22 configured as USB0_VBUS */ + + + /* MCXA15 USB configurations */ +#if PORT_SUPPORT_DEVICE(0) && (CFG_TUSB_MCU == OPT_MCU_MCXA15) + + RESET_PeripheralReset(kUSB0_RST_SHIFT_RSTn); + CLOCK_EnableUsbfsClock(); + +#endif + + + /* MCXN9 USB configurations */ +#if PORT_SUPPORT_DEVICE(0) && (CFG_TUSB_MCU == OPT_MCU_MCXN9) + // Port0 is Full Speed + + CLOCK_AttachClk(kCLK_48M_to_USB0); + CLOCK_EnableClock(kCLOCK_Usb0Ram); + CLOCK_EnableClock(kCLOCK_Usb0Fs); + CLOCK_EnableUsbfsClock(); + +#endif + +#if PORT_SUPPORT_DEVICE(1) && (CFG_TUSB_MCU == OPT_MCU_MCXN9) + // Port1 is High Speed + + // Power + SPC0->ACTIVE_VDELAY = 0x0500; + /* Change the power DCDC to 1.8v (By default, DCDC is 1.8V), CORELDO to 1.1v (By default, CORELDO is 1.0V) */ + SPC0->ACTIVE_CFG &= ~SPC_ACTIVE_CFG_CORELDO_VDD_DS_MASK; + SPC0->ACTIVE_CFG |= SPC_ACTIVE_CFG_DCDC_VDD_LVL(0x3) | SPC_ACTIVE_CFG_CORELDO_VDD_LVL(0x3) | + SPC_ACTIVE_CFG_SYSLDO_VDD_DS_MASK | SPC_ACTIVE_CFG_DCDC_VDD_DS(0x2u); + /* Wait until it is done */ + while (SPC0->SC & SPC_SC_BUSY_MASK) {} + if (0u == (SCG0->LDOCSR & SCG_LDOCSR_LDOEN_MASK)) { + SCG0->TRIM_LOCK = 0x5a5a0001U; + SCG0->LDOCSR |= SCG_LDOCSR_LDOEN_MASK; + /* wait LDO ready */ + while (0U == (SCG0->LDOCSR & SCG_LDOCSR_VOUT_OK_MASK)); + } + SYSCON->AHBCLKCTRLSET[2] |= SYSCON_AHBCLKCTRL2_USB_HS_MASK | SYSCON_AHBCLKCTRL2_USB_HS_PHY_MASK; + SCG0->SOSCCFG &= ~(SCG_SOSCCFG_RANGE_MASK | SCG_SOSCCFG_EREFS_MASK); + /* xtal = 20 ~ 30MHz */ + SCG0->SOSCCFG = (1U << SCG_SOSCCFG_RANGE_SHIFT) | (1U << SCG_SOSCCFG_EREFS_SHIFT); + SCG0->SOSCCSR |= SCG_SOSCCSR_SOSCEN_MASK; + while (1) { + if (SCG0->SOSCCSR & SCG_SOSCCSR_SOSCVLD_MASK) { + break; + } + } + + // Clock + SYSCON->CLOCK_CTRL |= SYSCON_CLOCK_CTRL_CLKIN_ENA_MASK | SYSCON_CLOCK_CTRL_CLKIN_ENA_FM_USBH_LPT_MASK; + CLOCK_EnableClock(kCLOCK_UsbHs); + CLOCK_EnableClock(kCLOCK_UsbHsPhy); + CLOCK_EnableUsbhsPhyPllClock(kCLOCK_Usbphy480M, 24000000U); + CLOCK_EnableUsbhsClock(); + + // USB PHY +#if ((!(defined FSL_FEATURE_SOC_CCM_ANALOG_COUNT)) && (!(defined FSL_FEATURE_SOC_ANATOP_COUNT))) + USBPHY->TRIM_OVERRIDE_EN = 0x001fU; /* override IFR value */ +#endif + + // Enable PHY support for Low speed device + LS via FS Hub + USBPHY->CTRL |= USBPHY_CTRL_SET_ENUTMILEVEL2_MASK | USBPHY_CTRL_SET_ENUTMILEVEL3_MASK; + + // Enable all power for normal operation + USBPHY->PWD = 0; + + // TX Timing + uint32_t phytx = USBPHY->TX; + phytx &= ~(USBPHY_TX_D_CAL_MASK | USBPHY_TX_TXCAL45DM_MASK | USBPHY_TX_TXCAL45DP_MASK); + phytx |= USBPHY_TX_D_CAL(0x04) | USBPHY_TX_TXCAL45DP(0x07) | USBPHY_TX_TXCAL45DM(0x07); + //phytx |= USBPHY_TX_D_CAL(0x0C) | USBPHY_TX_TXCAL45DP(0x06) | USBPHY_TX_TXCAL45DM(0x06); + USBPHY->TX = phytx; +#endif +} + +//--------------------------------------------------------------------+ +// Board porting API +//--------------------------------------------------------------------+ + +void board_led_write(bool state) +{ + GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); + +#ifdef NEOPIXEL_PIN + if (state) { + sctpix_setPixel(NEOPIXEL_CH, 0, 0x100000); + sctpix_setPixel(NEOPIXEL_CH, 1, 0x101010); + } else { + sctpix_setPixel(NEOPIXEL_CH, 0, 0x001000); + sctpix_setPixel(NEOPIXEL_CH, 1, 0x000010); + } + sctpix_show(); +#endif +} + +uint32_t board_button_read(void) +{ +#ifdef BUTTON_GPIO + return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); +#endif +} + +int board_uart_read(uint8_t* buf, int len) +{ + (void) buf; (void) len; + return 0; +} + +int board_uart_write(void const * buf, int len) +{ +#ifdef UART_DEV + LPUART_WriteBlocking(UART_DEV, (uint8_t const *) buf, len); + return len; +#else + (void) buf; (void) len; + return 0; +#endif +} + +#if CFG_TUSB_OS == OPT_OS_NONE +volatile uint32_t system_ticks = 0; +void SysTick_Handler(void) +{ + system_ticks++; +} + +uint32_t board_millis(void) +{ + return system_ticks; +} +#endif diff --git a/hw/bsp/mcx/family.cmake b/hw/bsp/mcx/family.cmake new file mode 100644 index 000000000..078d13b9f --- /dev/null +++ b/hw/bsp/mcx/family.cmake @@ -0,0 +1,122 @@ +include_guard() + +if (NOT BOARD) + message(FATAL_ERROR "BOARD not specified") +endif () + +set(SDK_DIR ${TOP}/hw/mcu/nxp/mcux-sdk) +set(CMSIS_DIR ${TOP}/lib/CMSIS_5) + +# include board specific +include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) + +# toolchain set up +set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOLCHAIN}.cmake) + +#------------------------------------ +# BOARD_TARGET +#------------------------------------ +# only need to be built ONCE for all examples +function(add_board_target BOARD_TARGET) + if (NOT TARGET ${BOARD_TARGET}) + add_library(${BOARD_TARGET} STATIC + # external driver + #lib/sct_neopixel/sct_neopixel.c + + # driver + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_gpio.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_common_arm.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpuart.c + + # mcu + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_reset.c + ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_CORE}.c + ) + + if (${FAMILY_MCUS} STREQUAL "MCXN9") + target_sources(${BOARD_TARGET} PRIVATE + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpflexcomm.c + ) + elseif(${FAMILY_MCUS} STREQUAL "MCXA15") + target_sources(${BOARD_TARGET} PRIVATE + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_spc.c + ) + endif() + + # target_compile_definitions(${BOARD_TARGET} PUBLIC + # ) + target_include_directories(${BOARD_TARGET} PUBLIC + # driver + # mcu + ${CMSIS_DIR}/CMSIS/Core/Include + ${SDK_DIR}/devices/${MCU_VARIANT} + ${SDK_DIR}/devices/${MCU_VARIANT}/drivers + ) + + update_board(${BOARD_TARGET}) + + if (CMAKE_C_COMPILER_ID STREQUAL "GNU") + target_sources(${BOARD_TARGET} PUBLIC + ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_CORE}.S + ) + target_link_options(${BOARD_TARGET} PUBLIC + # linker file + "LINKER:--script=${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_CORE}_flash.ld" + # nanolib + --specs=nosys.specs + --specs=nano.specs + ) + elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") + target_link_options(${BOARD_TARGET} PUBLIC + "LINKER:--config=${LD_FILE_IAR}" + ) + endif () + endif () +endfunction() + + +#------------------------------------ +# Functions +#------------------------------------ +function(family_configure_example TARGET RTOS) + family_configure_common(${TARGET} ${RTOS}) + + # Board target + add_board_target(board_${BOARD}) + + #---------- Port Specific ---------- + # These files are built for each example since it depends on example's tusb_config.h + target_sources(${TARGET} PUBLIC + # BSP + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c + ) + target_include_directories(${TARGET} PUBLIC + # family, hw, board + ${CMAKE_CURRENT_FUNCTION_LIST_DIR} + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../ + ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} + ) + + # Add TinyUSB target and port source + if (${FAMILY_MCUS} STREQUAL "MCXN9") + family_add_tinyusb(${TARGET} OPT_MCU_MCXN9 ${RTOS}) + elseif(${FAMILY_MCUS} STREQUAL "MCXA15") + family_add_tinyusb(${TARGET} OPT_MCU_MCXA15 ${RTOS}) + endif() + + target_sources(${TARGET}-tinyusb PUBLIC + # TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS + ${TOP}/src/portable/chipidea/$ + ) + target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) + + # Link dependencies + target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) + + # Flashing + family_flash_jlink(${TARGET}) + #family_flash_nxplink(${TARGET}) + #family_flash_pyocd(${TARGET}) +endfunction() diff --git a/hw/bsp/mcx/family.mk b/hw/bsp/mcx/family.mk new file mode 100644 index 000000000..59170271c --- /dev/null +++ b/hw/bsp/mcx/family.mk @@ -0,0 +1,65 @@ +UF2_FAMILY_ID = 0x2abc77ec +SDK_DIR = hw/mcu/nxp/mcux-sdk + +DEPS_SUBMODULES += $(SDK_DIR) lib/CMSIS_5 + +include $(TOP)/$(BOARD_PATH)/board.mk + +# Default to Highspeed PORT1 +PORT ?= 1 + +CFLAGS += \ + -flto \ + -DBOARD_TUD_RHPORT=$(PORT) \ + +# mcu driver cause following warnings +CFLAGS += -Wno-error=unused-parameter -Wno-error=old-style-declaration + +LDFLAGS_GCC += -specs=nosys.specs -specs=nano.specs + +# All source paths should be relative to the top level. +LD_FILE ?= $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/$(MCU_CORE)_flash.ld + +# TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS +ifeq ($(PORT), 1) + $(info "PORT1 High Speed") + CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED + SRC_C += src/portable/chipidea/ci_hs/dcd_ci_hs.c +else + $(info "PORT0 Full Speed") + CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED + SRC_C += src/portable/chipidea/ci_fs/dcd_ci_fs.c +endif + +SRC_C += \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/system_$(MCU_CORE).c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_clock.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_reset.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_gpio.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpuart.c \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_common_arm.c \ + + +# fsl_lpflexcomm just needed for MCXN9 +ifeq ($(MCU_VARIANT), MCXN947) + SRC_C += \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpflexcomm.c \ + +endif + +# fsl_spc just needed for MCXNA15 +ifeq ($(MCU_VARIANT), MCXA153) + SRC_C += \ + $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_spc.c \ + +endif + + + +INC += \ + $(TOP)/$(BOARD_PATH) \ + $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ + $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT) \ + $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers \ + +SRC_S += $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/startup_$(MCU_CORE).S diff --git a/hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h deleted file mode 100644 index 6f10a7ab0..000000000 --- a/hw/bsp/mcxa/FreeRTOSConfig/FreeRTOSConfig.h +++ /dev/null @@ -1,149 +0,0 @@ -/* - * FreeRTOS Kernel V10.0.0 - * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. - * - * Permission is hereby granted, free of charge, to any person obtaining a copy of - * this software and associated documentation files (the "Software"), to deal in - * the Software without restriction, including without limitation the rights to - * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of - * the Software, and to permit persons to whom the Software is furnished to do so, - * subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in all - * copies or substantial portions of the Software. If you wish to use our Amazon - * FreeRTOS name, please do so in a fair use way that does not cause confusion. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS - * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR - * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER - * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN - * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. - * - * http://www.FreeRTOS.org - * http://aws.amazon.com/freertos - * - * 1 tab == 4 spaces! - */ - - -#ifndef FREERTOS_CONFIG_H -#define FREERTOS_CONFIG_H - -/*----------------------------------------------------------- - * Application specific definitions. - * - * These definitions should be adjusted for your particular hardware and - * application requirements. - * - * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE - * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. - * - * See http://www.freertos.org/a00110.html. - *----------------------------------------------------------*/ - -// skip if included from IAR assembler -#ifndef __IASMARM__ - #include "fsl_device_registers.h" -#endif - -/* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 1 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) - -#define configUSE_PREEMPTION 1 -#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 -#define configCPU_CLOCK_HZ SystemCoreClock -#define configTICK_RATE_HZ ( 1000 ) -#define configMAX_PRIORITIES ( 5 ) -#define configMINIMAL_STACK_SIZE ( 128 ) -#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) -#define configMAX_TASK_NAME_LEN 16 -#define configUSE_16_BIT_TICKS 0 -#define configIDLE_SHOULD_YIELD 1 -#define configUSE_MUTEXES 1 -#define configUSE_RECURSIVE_MUTEXES 1 -#define configUSE_COUNTING_SEMAPHORES 1 -#define configQUEUE_REGISTRY_SIZE 4 -#define configUSE_QUEUE_SETS 0 -#define configUSE_TIME_SLICING 0 -#define configUSE_NEWLIB_REENTRANT 0 -#define configENABLE_BACKWARD_COMPATIBILITY 1 -#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 - -#define configSUPPORT_STATIC_ALLOCATION 1 -#define configSUPPORT_DYNAMIC_ALLOCATION 0 - -/* Hook function related definitions. */ -#define configUSE_IDLE_HOOK 0 -#define configUSE_TICK_HOOK 0 -#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning -#define configCHECK_FOR_STACK_OVERFLOW 2 -#define configCHECK_HANDLER_INSTALLATION 0 - -/* Run time and task stats gathering related definitions. */ -#define configGENERATE_RUN_TIME_STATS 0 -#define configRECORD_STACK_HIGH_ADDRESS 1 -#define configUSE_TRACE_FACILITY 1 // legacy trace -#define configUSE_STATS_FORMATTING_FUNCTIONS 0 - -/* Co-routine definitions. */ -#define configUSE_CO_ROUTINES 0 -#define configMAX_CO_ROUTINE_PRIORITIES 2 - -/* Software timer related definitions. */ -#define configUSE_TIMERS 1 -#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) -#define configTIMER_QUEUE_LENGTH 32 -#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE - -/* Optional functions - most linkers will remove unused functions anyway. */ -#define INCLUDE_vTaskPrioritySet 0 -#define INCLUDE_uxTaskPriorityGet 0 -#define INCLUDE_vTaskDelete 0 -#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY -#define INCLUDE_xResumeFromISR 0 -#define INCLUDE_vTaskDelayUntil 1 -#define INCLUDE_vTaskDelay 1 -#define INCLUDE_xTaskGetSchedulerState 0 -#define INCLUDE_xTaskGetCurrentTaskHandle 1 -#define INCLUDE_uxTaskGetStackHighWaterMark 0 -#define INCLUDE_xTaskGetIdleTaskHandle 0 -#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 -#define INCLUDE_pcTaskGetTaskName 0 -#define INCLUDE_eTaskGetState 0 -#define INCLUDE_xEventGroupSetBitFromISR 0 -#define INCLUDE_xTimerPendFunctionCall 0 - -/* FreeRTOS hooks to NVIC vectors */ -#define xPortPendSVHandler PendSV_Handler -#define xPortSysTickHandler SysTick_Handler -#define vPortSVCHandler SVC_Handler - -//--------------------------------------------------------------------+ -// Interrupt nesting behavior configuration. -//--------------------------------------------------------------------+ - -// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header -#define configPRIO_BITS 3 - -/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ -#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1<FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P0V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - } - - CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ - - CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO12M */ - - /* The flow of decreasing voltage and frequency */ - if (coreFreq > BOARD_BOOTCLOCKFRO12M_CORE_CLOCK) { - /* Configure Flash to support different voltage level and frequency */ - FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P0V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - /* Set the LDO_CORE VDD regulator level */ - ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; - ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; - (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); - } - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - - /*!< Set up dividers */ - CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK; -} -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO24M ********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFRO24M -outputs: -- {id: CLK_1M_clock.outFreq, value: 1 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: CPU_clock.outFreq, value: 24 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_DIV_clock.outFreq, value: 48 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 48 MHz} -- {id: Slow_clock.outFreq, value: 6 MHz} -- {id: System_clock.outFreq, value: 24 MHz} -settings: -- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} -- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFRO24M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFRO24M configuration - ******************************************************************************/ -void BOARD_BootClockFRO24M(void) -{ - uint32_t coreFreq; - spc_active_mode_core_ldo_option_t ldoOption; - spc_sram_voltage_config_t sramOption; - - /* Get the CPU Core frequency */ - coreFreq = CLOCK_GetCoreSysClkFreq(); - - /* The flow of increasing voltage and frequency */ - if (coreFreq <= BOARD_BOOTCLOCKFRO24M_CORE_CLOCK) { - /* Set the LDO_CORE VDD regulator level */ - ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; - ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; - (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); - /* Configure Flash to support different voltage level and frequency */ - FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P0V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - } - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ - - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ - - /* The flow of decreasing voltage and frequency */ - if (coreFreq > BOARD_BOOTCLOCKFRO24M_CORE_CLOCK) { - /* Configure Flash to support different voltage level and frequency */ - FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x0U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P0V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - /* Set the LDO_CORE VDD regulator level */ - ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; - ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; - (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); - } - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - - /*!< Set up dividers */ - CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 2U); /* !< Set AHBCLKDIV divider to value 2 */ - CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFRO24M_CORE_CLOCK; -} -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO48M ********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFRO48M -outputs: -- {id: CLK_1M_clock.outFreq, value: 1 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: CPU_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_DIV_clock.outFreq, value: 48 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 48 MHz} -- {id: Slow_clock.outFreq, value: 12 MHz} -- {id: System_clock.outFreq, value: 48 MHz} -settings: -- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFRO48M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFRO48M configuration - ******************************************************************************/ -void BOARD_BootClockFRO48M(void) -{ - uint32_t coreFreq; - spc_active_mode_core_ldo_option_t ldoOption; - spc_sram_voltage_config_t sramOption; - - /* Get the CPU Core frequency */ - coreFreq = CLOCK_GetCoreSysClkFreq(); - - /* The flow of increasing voltage and frequency */ - if (coreFreq <= BOARD_BOOTCLOCKFRO48M_CORE_CLOCK) { - /* Set the LDO_CORE VDD regulator level */ - ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; - ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; - (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); - /* Configure Flash to support different voltage level and frequency */ - FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P0V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - } - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ - - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ - - /* The flow of decreasing voltage and frequency */ - if (coreFreq > BOARD_BOOTCLOCKFRO48M_CORE_CLOCK) { - /* Configure Flash to support different voltage level and frequency */ - FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P0V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - /* Set the LDO_CORE VDD regulator level */ - ldoOption.CoreLDOVoltage = kSPC_CoreLDO_MidDriveVoltage; - ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; - (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); - } - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - - /*!< Set up dividers */ - CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ - CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFRO48M_CORE_CLOCK; -} -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO64M ********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFRO64M -outputs: -- {id: CLK_1M_clock.outFreq, value: 1 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: CPU_clock.outFreq, value: 64 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_DIV_clock.outFreq, value: 64 MHz} -- {id: FRO_HF_clock.outFreq, value: 64 MHz} -- {id: MAIN_clock.outFreq, value: 64 MHz} -- {id: Slow_clock.outFreq, value: 16 MHz} -- {id: System_clock.outFreq, value: 64 MHz} -settings: -- {id: VDD_CORE, value: voltage_1v1} -- {id: MRCC.FROHFDIV.scale, value: '1', locked: true} -- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} -- {id: SYSCON.AHBCLKDIV.scale, value: '1', locked: true} -sources: -- {id: SCG.FIRC.outFreq, value: 64 MHz} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFRO64M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFRO64M configuration - ******************************************************************************/ -void BOARD_BootClockFRO64M(void) -{ - uint32_t coreFreq; - spc_active_mode_core_ldo_option_t ldoOption; - spc_sram_voltage_config_t sramOption; - - /* Get the CPU Core frequency */ - coreFreq = CLOCK_GetCoreSysClkFreq(); - - /* The flow of increasing voltage and frequency */ - if (coreFreq <= BOARD_BOOTCLOCKFRO64M_CORE_CLOCK) { - /* Set the LDO_CORE VDD regulator level */ - ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; - ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; - (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); - /* Configure Flash to support different voltage level and frequency */ - FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P1V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - } - - CLOCK_SetupFROHFClocking(64000000U); /*!< Enable FRO HF(64MHz) output */ - - CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ - - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ - - /* The flow of decreasing voltage and frequency */ - if (coreFreq > BOARD_BOOTCLOCKFRO64M_CORE_CLOCK) { - /* Configure Flash to support different voltage level and frequency */ - FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x1U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P1V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - /* Set the LDO_CORE VDD regulator level */ - ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; - ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; - (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); - } - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - - /*!< Set up dividers */ - CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ - CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFRO64M_CORE_CLOCK; -} -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO96M ********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFRO96M -called_from_default_init: true -outputs: -- {id: CLK_1M_clock.outFreq, value: 1 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: CPU_clock.outFreq, value: 96 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_DIV_clock.outFreq, value: 96 MHz} -- {id: FRO_HF_clock.outFreq, value: 96 MHz} -- {id: MAIN_clock.outFreq, value: 96 MHz} -- {id: Slow_clock.outFreq, value: 24 MHz} -- {id: System_clock.outFreq, value: 96 MHz} -settings: -- {id: VDD_CORE, value: voltage_1v1} -- {id: CLKOUTDIV_HALT, value: Enable} -- {id: MRCC.FROHFDIV.scale, value: '1', locked: true} -- {id: MRCC.OSTIMERCLKSEL.sel, value: VBAT.CLK16K_1} -- {id: SYSCON.AHBCLKDIV.scale, value: '1', locked: true} -sources: -- {id: SCG.FIRC.outFreq, value: 96 MHz} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFRO96M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFRO96M configuration - ******************************************************************************/ -void BOARD_BootClockFRO96M(void) -{ - uint32_t coreFreq; - spc_active_mode_core_ldo_option_t ldoOption; - spc_sram_voltage_config_t sramOption; - - /* Get the CPU Core frequency */ - coreFreq = CLOCK_GetCoreSysClkFreq(); - - /* The flow of increasing voltage and frequency */ - if (coreFreq <= BOARD_BOOTCLOCKFRO96M_CORE_CLOCK) { - /* Set the LDO_CORE VDD regulator level */ - ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; - ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; - (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); - /* Configure Flash to support different voltage level and frequency */ - FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x2U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P1V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - } - - CLOCK_SetupFROHFClocking(96000000U); /*!< Enable FRO HF(96MHz) output */ - - CLOCK_SetupFRO12MClocking(); /*!< Setup FRO12M clock */ - - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /* !< Switch MAIN_CLK to FRO_HF */ - - /* The flow of decreasing voltage and frequency */ - if (coreFreq > BOARD_BOOTCLOCKFRO96M_CORE_CLOCK) { - /* Configure Flash to support different voltage level and frequency */ - FMU0->FCTRL = (FMU0->FCTRL & ~((uint32_t)FMU_FCTRL_RWSC_MASK)) | (FMU_FCTRL_RWSC(0x2U)); - /* Specifies the operating voltage for the SRAM's read/write timing margin */ - sramOption.operateVoltage = kSPC_sramOperateAt1P1V; - sramOption.requestVoltageUpdate = true; - (void)SPC_SetSRAMOperateVoltage(SPC0, &sramOption); - /* Set the LDO_CORE VDD regulator level */ - ldoOption.CoreLDOVoltage = kSPC_CoreLDO_NormalVoltage; - ldoOption.CoreLDODriveStrength = kSPC_CoreLDO_NormalDriveStrength; - (void)SPC_SetActiveModeCoreLDORegulatorConfig(SPC0, &ldoOption); - } - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - - /*!< Set up dividers */ - CLOCK_SetClockDiv(kCLOCK_DivAHBCLK, 1U); /* !< Set AHBCLKDIV divider to value 1 */ - CLOCK_SetClockDiv(kCLOCK_DivFRO_HF_DIV, 1U); /* !< Set FROHFDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFRO96M_CORE_CLOCK; -} diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h b/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h deleted file mode 100644 index 079d0d312..000000000 --- a/hw/bsp/mcxa/boards/frdmmcxa153/clock_config.h +++ /dev/null @@ -1,170 +0,0 @@ -/* - * Copyright 2023 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _CLOCK_CONFIG_H_ -#define _CLOCK_CONFIG_H_ - -#include "fsl_common.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes default configuration of clocks. - * - */ -void BOARD_InitBootClocks(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO12M ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK 12000000U /*!< Core clock frequency: 12000000Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFRO12M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO24M ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFRO24M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFRO24M_CORE_CLOCK 24000000U /*!< Core clock frequency: 24000000Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFRO24M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFRO24M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO48M ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFRO48M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFRO48M_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFRO48M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFRO48M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO64M ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFRO64M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFRO64M_CORE_CLOCK 64000000U /*!< Core clock frequency: 64000000Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFRO64M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFRO64M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO96M ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFRO96M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFRO96M_CORE_CLOCK 96000000U /*!< Core clock frequency: 96000000Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFRO96M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFRO96M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c deleted file mode 100644 index b0e6de560..000000000 --- a/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.c +++ /dev/null @@ -1,159 +0,0 @@ -/* - * Copyright 2023 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Pins v14.0 -processor: MCXA153 -package_id: MCXA153VLH -mcu_data: ksdk2_0 -processor_version: 0.14.3 -pin_labels: -- {pin_num: '38', pin_signal: P3_12/LPUART2_RTS_B/CT1_MAT2/PWM0_X0, label: LED_RED, identifier: LED_RED} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -#include "fsl_common.h" -#include "fsl_port.h" -#include "fsl_gpio.h" -#include "pin_mux.h" - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitBootPins - * Description : Calls initialization functions. - * - * END ****************************************************************************************************************/ -void BOARD_InitBootPins(void) -{ - BOARD_InitPins(); -} - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -BOARD_InitPins: -- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'} -- pin_list: - - {pin_num: '38', peripheral: GPIO3, signal: 'GPIO, 12', pin_signal: P3_12/LPUART2_RTS_B/CT1_MAT2/PWM0_X0, direction: OUTPUT, gpio_init_state: 'false', slew_rate: fast, - open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitPins - * Description : Configures pin routing and optionally pin electrical features. - * - * END ****************************************************************************************************************/ -void BOARD_InitPins(void) -{ - RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn); - RESET_PeripheralReset(kPORT0_RST_SHIFT_RSTn); - CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u); - CLOCK_AttachClk(kFRO12M_to_LPUART0); - - /* write to PORT0: Peripheral clock is enabled */ - CLOCK_EnableClock(kCLOCK_GatePORT0); - - /* Write to GPIO3: Peripheral clock is enabled */ - CLOCK_EnableClock(kCLOCK_GateGPIO3); - /* Write to PORT3: Peripheral clock is enabled */ - CLOCK_EnableClock(kCLOCK_GatePORT3); - /* GPIO3 peripheral is released from reset */ - RESET_ReleasePeripheralReset(kGPIO3_RST_SHIFT_RSTn); - /* PORT3 peripheral is released from reset */ - RESET_ReleasePeripheralReset(kPORT3_RST_SHIFT_RSTn); - - const port_pin_config_t port3_12_pin38_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Normal drive strength is configured */ - kPORT_NormalDriveStrength, - /* Pin is configured as P3_12 */ - kPORT_MuxAlt0, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT3_12 (pin 38) is configured as P3_12 */ - PORT_SetPinConfig(PORT3, 12U, &port3_12_pin38_config); - - const port_pin_config_t port0_2_pin51_config = {/* Internal pull-up resistor is enabled */ - kPORT_PullUp, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Normal drive strength is configured */ - kPORT_NormalDriveStrength, - /* Pin is configured as LPUART0_RXD */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT0_2 (pin 51) is configured as LPUART0_RXD */ - PORT_SetPinConfig(PORT0, 2U, &port0_2_pin51_config); - - const port_pin_config_t port0_3_pin52_config = {/* Internal pull-up resistor is enabled */ - kPORT_PullUp, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Normal drive strength is configured */ - kPORT_NormalDriveStrength, - /* Pin is configured as LPUART0_TXD */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT0_3 (pin 52) is configured as LPUART0_TXD */ - PORT_SetPinConfig(PORT0, 3U, &port0_3_pin52_config); - -} -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h b/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h deleted file mode 100644 index 06b6fdee9..000000000 --- a/hw/bsp/mcxa/boards/frdmmcxa153/pin_mux.h +++ /dev/null @@ -1,47 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -#ifndef _PIN_MUX_H_ -#define _PIN_MUX_H_ - -/*! - * @addtogroup pin_mux - * @{ - */ - -/*********************************************************************************************************************** - * API - **********************************************************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif - -/*! - * @brief Calls initialization functions. - * - */ -void BOARD_InitBootPins(void); - -/*! - * @brief Configures pin routing and optionally pin electrical features. - * - */ -void BOARD_InitPins(void); - -#if defined(__cplusplus) -} -#endif - -/*! - * @} - */ -#endif /* _PIN_MUX_H_ */ - -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/hw/bsp/mcxa/debug.jlinkscript b/hw/bsp/mcxa/debug.jlinkscript deleted file mode 100644 index fd8bcffef..000000000 --- a/hw/bsp/mcxa/debug.jlinkscript +++ /dev/null @@ -1,5 +0,0 @@ -int SetupTarget(void) { - JLINK_ExecCommand("SetRTTSearchRanges 0x20000000 0x40000"); - - return 0; -} diff --git a/hw/bsp/mcxa/family.c b/hw/bsp/mcxa/family.c deleted file mode 100644 index d2bc35f8c..000000000 --- a/hw/bsp/mcxa/family.c +++ /dev/null @@ -1,161 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2018, hathach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "bsp/board_api.h" -#include "fsl_device_registers.h" -#include "fsl_gpio.h" -#include "fsl_lpuart.h" -#include "board.h" - -#include "pin_mux.h" -#include "clock_config.h" - - -#ifdef BOARD_TUD_RHPORT - #define PORT_SUPPORT_DEVICE(_n) (BOARD_TUD_RHPORT == _n) -#else - #define PORT_SUPPORT_DEVICE(_n) 0 -#endif - -#ifdef BOARD_TUH_RHPORT - #define PORT_SUPPORT_HOST(_n) (BOARD_TUH_RHPORT == _n) -#else - #define PORT_SUPPORT_HOST(_n) 0 -#endif - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void USB0_IRQHandler(void) -{ - tud_int_handler(0); -} - -void board_init(void) -{ - BOARD_InitPins(); - BOARD_InitBootClocks(); - CLOCK_SetupExtClocking(XTAL0_CLK_HZ); - - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); - - // LED - CLOCK_EnableClock(LED_CLK); - gpio_pin_config_t LED_RED_config = { - .pinDirection = kGPIO_DigitalOutput, - .outputLogic = 0U - }; - - /* Initialize GPIO functionality on pin PIO3_12 (pin 38) */ - GPIO_PinInit(LED_GPIO, LED_PIN, &LED_RED_config); - board_led_write(1); - - // Button -#ifdef BUTTON_GPIO - CLOCK_EnableClock(BUTTON_CLK); - gpio_pin_config_t const button_config = { kGPIO_DigitalInput, 0}; - GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); -#endif - -#ifdef UART_DEV - - CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u); - CLOCK_AttachClk(kFRO12M_to_LPUART0); - RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn); - - lpuart_config_t uart_config; - LPUART_GetDefaultConfig(&uart_config); - uart_config.baudRate_Bps = 115200; - uart_config.enableTx = true; - uart_config.enableRx = false; - LPUART_Init(UART_DEV, &uart_config, 12000000u); - - -#endif - - // USB VBUS - /* PORT0 PIN22 configured as USB0_VBUS */ - -#if PORT_SUPPORT_DEVICE(0) - RESET_PeripheralReset(kUSB0_RST_SHIFT_RSTn); - CLOCK_EnableUsbfsClock(); -#endif - -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); -} - -uint32_t board_button_read(void) -{ -#ifdef BUTTON_GPIO - return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); -#else - return 1; -#endif -} - -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; - return 0; -} - -int board_uart_write(void const * buf, int len) -{ -#ifdef UART_DEV - LPUART_WriteBlocking(UART_DEV, (uint8_t const *) buf, len); - return len; -#else - (void) buf; (void) len; - return 0; -#endif -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif - \ No newline at end of file diff --git a/hw/bsp/mcxa/family.cmake b/hw/bsp/mcxa/family.cmake deleted file mode 100644 index d2b2321d6..000000000 --- a/hw/bsp/mcxa/family.cmake +++ /dev/null @@ -1,110 +0,0 @@ -include_guard() - -if (NOT BOARD) - message(FATAL_ERROR "BOARD not specified") -endif () - -set(SDK_DIR ${TOP}/hw/mcu/nxp/mcux-sdk) -set(CMSIS_DIR ${TOP}/lib/CMSIS_5) - -# include board specific -include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) - -# toolchain set up -set(CMAKE_SYSTEM_PROCESSOR cortex-m33-nodsp-nofp CACHE INTERNAL "System Processor") -set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOLCHAIN}.cmake) - -set(FAMILY_MCUS MCXA CACHE INTERNAL "") - - -#------------------------------------ -# BOARD_TARGET -#------------------------------------ -# only need to be built ONCE for all examples -function(add_board_target BOARD_TARGET) - if (NOT TARGET ${BOARD_TARGET}) - add_library(${BOARD_TARGET} STATIC - # external driver - #lib/sct_neopixel/sct_neopixel.c - - # driver - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_gpio.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_common_arm.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpuart.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_spc.c - # mcu - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_reset.c - ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_CORE}.c - ) - # target_compile_definitions(${BOARD_TARGET} PUBLIC - # ) - target_include_directories(${BOARD_TARGET} PUBLIC - # driver - # mcu - ${CMSIS_DIR}/CMSIS/Core/Include - ${SDK_DIR}/devices/${MCU_VARIANT} - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers - ) - - update_board(${BOARD_TARGET}) - - if (CMAKE_C_COMPILER_ID STREQUAL "GNU") - target_sources(${BOARD_TARGET} PUBLIC - ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_CORE}.S - ) - target_link_options(${BOARD_TARGET} PUBLIC - # linker file - "LINKER:--script=${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_CORE}_flash.ld" - # nanolib - --specs=nosys.specs - --specs=nano.specs - ) - elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") - target_link_options(${BOARD_TARGET} PUBLIC - "LINKER:--config=${LD_FILE_IAR}" - ) - endif () - endif () -endfunction() - - -#------------------------------------ -# Functions -#------------------------------------ -function(family_configure_example TARGET RTOS) - family_configure_common(${TARGET} ${RTOS}) - - # Board target - add_board_target(board_${BOARD}) - - #---------- Port Specific ---------- - # These files are built for each example since it depends on example's tusb_config.h - target_sources(${TARGET} PUBLIC - # BSP - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c - ) - target_include_directories(${TARGET} PUBLIC - # family, hw, board - ${CMAKE_CURRENT_FUNCTION_LIST_DIR} - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../ - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} - ) - - # Add TinyUSB target and port source - family_add_tinyusb(${TARGET} OPT_MCU_MCXA ${RTOS}) - target_sources(${TARGET}-tinyusb PUBLIC - # TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS - ${TOP}/src/portable/chipidea/ci_fs/dcd_ci_fs.c - ) - target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) - - # Link dependencies - target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) - - # Flashing - family_flash_jlink(${TARGET}) - #family_flash_nxplink(${TARGET}) - #family_flash_pyocd(${TARGET}) -endfunction() diff --git a/hw/bsp/mcxa/family.mk b/hw/bsp/mcxa/family.mk deleted file mode 100644 index 87ae92fab..000000000 --- a/hw/bsp/mcxa/family.mk +++ /dev/null @@ -1,42 +0,0 @@ -UF2_FAMILY_ID = 0x2abc77ec -SDK_DIR = hw/mcu/nxp/mcux-sdk - -DEPS_SUBMODULES += $(SDK_DIR) lib/CMSIS_5 #not found - -include $(TOP)/$(BOARD_PATH)/board.mk -CPU_CORE ?= cortex-m33-nodsp-nofp - -CFLAGS += \ - -flto \ - -DCFG_TUSB_MCU=OPT_MCU_MCXA \ - -DBOARD_TUD_RHPORT=0 - -# mcu driver cause following warnings -CFLAGS += -Wno-error=unused-parameter -Wno-error=old-style-declaration - -LDFLAGS_GCC += -specs=nosys.specs -specs=nano.specs - -# All source paths should be relative to the top level. -LD_FILE ?= $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/$(MCU_CORE)_flash.ld - -# TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS -$(info "PORT0 Full Speed") -CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED -SRC_C += src/portable/chipidea/ci_fs/dcd_ci_fs.c - -SRC_C += \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/system_$(MCU_CORE).c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_clock.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_reset.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_gpio.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpuart.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_common_arm.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_spc.c -INC += \ - $(TOP)/$(BOARD_PATH) \ - $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ - $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT) \ - $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers - - -SRC_S += $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/startup_$(MCU_CORE).S diff --git a/hw/bsp/mcxn/FreeRTOSConfig/FreeRTOSConfig.h b/hw/bsp/mcxn/FreeRTOSConfig/FreeRTOSConfig.h deleted file mode 100644 index 6f10a7ab0..000000000 --- a/hw/bsp/mcxn/FreeRTOSConfig/FreeRTOSConfig.h +++ /dev/null @@ -1,149 +0,0 @@ -/* - * FreeRTOS Kernel V10.0.0 - * Copyright (C) 2017 Amazon.com, Inc. or its affiliates. All Rights Reserved. - * - * Permission is hereby granted, free of charge, to any person obtaining a copy of - * this software and associated documentation files (the "Software"), to deal in - * the Software without restriction, including without limitation the rights to - * use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of - * the Software, and to permit persons to whom the Software is furnished to do so, - * subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in all - * copies or substantial portions of the Software. If you wish to use our Amazon - * FreeRTOS name, please do so in a fair use way that does not cause confusion. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS - * FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR - * COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER - * IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN - * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. - * - * http://www.FreeRTOS.org - * http://aws.amazon.com/freertos - * - * 1 tab == 4 spaces! - */ - - -#ifndef FREERTOS_CONFIG_H -#define FREERTOS_CONFIG_H - -/*----------------------------------------------------------- - * Application specific definitions. - * - * These definitions should be adjusted for your particular hardware and - * application requirements. - * - * THESE PARAMETERS ARE DESCRIBED WITHIN THE 'CONFIGURATION' SECTION OF THE - * FreeRTOS API DOCUMENTATION AVAILABLE ON THE FreeRTOS.org WEB SITE. - * - * See http://www.freertos.org/a00110.html. - *----------------------------------------------------------*/ - -// skip if included from IAR assembler -#ifndef __IASMARM__ - #include "fsl_device_registers.h" -#endif - -/* Cortex M23/M33 port configuration. */ -#define configENABLE_MPU 0 -#define configENABLE_FPU 1 -#define configENABLE_TRUSTZONE 0 -#define configMINIMAL_SECURE_STACK_SIZE (1024) - -#define configUSE_PREEMPTION 1 -#define configUSE_PORT_OPTIMISED_TASK_SELECTION 0 -#define configCPU_CLOCK_HZ SystemCoreClock -#define configTICK_RATE_HZ ( 1000 ) -#define configMAX_PRIORITIES ( 5 ) -#define configMINIMAL_STACK_SIZE ( 128 ) -#define configTOTAL_HEAP_SIZE ( configSUPPORT_DYNAMIC_ALLOCATION*4*1024 ) -#define configMAX_TASK_NAME_LEN 16 -#define configUSE_16_BIT_TICKS 0 -#define configIDLE_SHOULD_YIELD 1 -#define configUSE_MUTEXES 1 -#define configUSE_RECURSIVE_MUTEXES 1 -#define configUSE_COUNTING_SEMAPHORES 1 -#define configQUEUE_REGISTRY_SIZE 4 -#define configUSE_QUEUE_SETS 0 -#define configUSE_TIME_SLICING 0 -#define configUSE_NEWLIB_REENTRANT 0 -#define configENABLE_BACKWARD_COMPATIBILITY 1 -#define configSTACK_ALLOCATION_FROM_SEPARATE_HEAP 0 - -#define configSUPPORT_STATIC_ALLOCATION 1 -#define configSUPPORT_DYNAMIC_ALLOCATION 0 - -/* Hook function related definitions. */ -#define configUSE_IDLE_HOOK 0 -#define configUSE_TICK_HOOK 0 -#define configUSE_MALLOC_FAILED_HOOK 0 // cause nested extern warning -#define configCHECK_FOR_STACK_OVERFLOW 2 -#define configCHECK_HANDLER_INSTALLATION 0 - -/* Run time and task stats gathering related definitions. */ -#define configGENERATE_RUN_TIME_STATS 0 -#define configRECORD_STACK_HIGH_ADDRESS 1 -#define configUSE_TRACE_FACILITY 1 // legacy trace -#define configUSE_STATS_FORMATTING_FUNCTIONS 0 - -/* Co-routine definitions. */ -#define configUSE_CO_ROUTINES 0 -#define configMAX_CO_ROUTINE_PRIORITIES 2 - -/* Software timer related definitions. */ -#define configUSE_TIMERS 1 -#define configTIMER_TASK_PRIORITY (configMAX_PRIORITIES-2) -#define configTIMER_QUEUE_LENGTH 32 -#define configTIMER_TASK_STACK_DEPTH configMINIMAL_STACK_SIZE - -/* Optional functions - most linkers will remove unused functions anyway. */ -#define INCLUDE_vTaskPrioritySet 0 -#define INCLUDE_uxTaskPriorityGet 0 -#define INCLUDE_vTaskDelete 0 -#define INCLUDE_vTaskSuspend 1 // required for queue, semaphore, mutex to be blocked indefinitely with portMAX_DELAY -#define INCLUDE_xResumeFromISR 0 -#define INCLUDE_vTaskDelayUntil 1 -#define INCLUDE_vTaskDelay 1 -#define INCLUDE_xTaskGetSchedulerState 0 -#define INCLUDE_xTaskGetCurrentTaskHandle 1 -#define INCLUDE_uxTaskGetStackHighWaterMark 0 -#define INCLUDE_xTaskGetIdleTaskHandle 0 -#define INCLUDE_xTimerGetTimerDaemonTaskHandle 0 -#define INCLUDE_pcTaskGetTaskName 0 -#define INCLUDE_eTaskGetState 0 -#define INCLUDE_xEventGroupSetBitFromISR 0 -#define INCLUDE_xTimerPendFunctionCall 0 - -/* FreeRTOS hooks to NVIC vectors */ -#define xPortPendSVHandler PendSV_Handler -#define xPortSysTickHandler SysTick_Handler -#define vPortSVCHandler SVC_Handler - -//--------------------------------------------------------------------+ -// Interrupt nesting behavior configuration. -//--------------------------------------------------------------------+ - -// For Cortex-M specific: __NVIC_PRIO_BITS is defined in mcu header -#define configPRIO_BITS 3 - -/* The lowest interrupt priority that can be used in a call to a "set priority" function. */ -#define configLIBRARY_LOWEST_INTERRUPT_PRIORITY ((1< - ) - target_sources(${TARGET} PUBLIC - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/clock_config.c - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/pin_mux.c - ) -endfunction() diff --git a/hw/bsp/mcxn/boards/frdmmcxn947/board.h b/hw/bsp/mcxn/boards/frdmmcxn947/board.h deleted file mode 100644 index acb73363f..000000000 --- a/hw/bsp/mcxn/boards/frdmmcxn947/board.h +++ /dev/null @@ -1,66 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#ifndef BOARD_H_ -#define BOARD_H_ - -#ifdef __cplusplus - extern "C" { -#endif - -// LED -#define LED_GPIO GPIO0 -#define LED_CLK kCLOCK_Gpio0 -#define LED_PIN 10 // red -#define LED_STATE_ON 0 - -// WAKE button (Dummy, use unused pin -#define BUTTON_GPIO GPIO0 -#define BUTTON_CLK kCLOCK_Gpio0 -#define BUTTON_PIN 23 -#define BUTTON_STATE_ACTIVE 0 - -// UART -#define UART_DEV LPUART4 - -static inline void board_uart_init_clock(void) { - /* attach FRO 12M to FLEXCOMM4 */ - CLOCK_SetClkDiv(kCLOCK_DivFlexcom4Clk, 1u); - CLOCK_AttachClk(kFRO12M_to_FLEXCOMM4); - RESET_ClearPeripheralReset(kFC4_RST_SHIFT_RSTn); -} - -//#define UART_RX_PINMUX 0, 24, IOCON_PIO_DIG_FUNC1_EN -//#define UART_TX_PINMUX 0, 25, IOCON_PIO_DIG_FUNC1_EN - -// XTAL -#define XTAL0_CLK_HZ (24 * 1000 * 1000U) - -#ifdef __cplusplus - } -#endif - -#endif diff --git a/hw/bsp/mcxn/boards/frdmmcxn947/board.mk b/hw/bsp/mcxn/boards/frdmmcxn947/board.mk deleted file mode 100644 index aaad5e73e..000000000 --- a/hw/bsp/mcxn/boards/frdmmcxn947/board.mk +++ /dev/null @@ -1,11 +0,0 @@ -MCU_VARIANT = MCXN947 -MCU_CORE = MCXN947_cm33_core0 -PORT ?= 1 - -CFLAGS += -DCPU_MCXN947VDF_cm33_core0 - -JLINK_DEVICE = MCXN947_M33_0 -PYOCD_TARGET = MCXN947 - -# flash using pyocd -flash: flash-jlink diff --git a/hw/bsp/mcxn/boards/frdmmcxn947/clock_config.c b/hw/bsp/mcxn/boards/frdmmcxn947/clock_config.c deleted file mode 100644 index 37d2b4dfc..000000000 --- a/hw/bsp/mcxn/boards/frdmmcxn947/clock_config.c +++ /dev/null @@ -1,338 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ -/* - * How to setup clock using clock driver functions: - * - * 1. Setup clock sources. - * - * 2. Set up wait states of the flash. - * - * 3. Set up all dividers. - * - * 4. Set up all selectors to provide selected clocks. - * - */ - -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Clocks v10.0 -processor: MCXN947 -package_id: MCXN947VDF -mcu_data: ksdk2_0 -processor_version: 0.12.3 -board: MCX-N9XX-EVK - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -#include "clock_config.h" -#include "fsl_clock.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ - -/******************************************************************************* - * Variables - ******************************************************************************/ -/* System clock frequency. */ -// extern uint32_t SystemCoreClock; - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ -void BOARD_InitBootClocks(void) -{ - BOARD_BootClockPLL150M(); -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO12M ********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFRO12M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: MAIN_clock.outFreq, value: 12 MHz} -- {id: Slow_clock.outFreq, value: 3 MHz} -- {id: System_clock.outFreq, value: 12 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SCGMode, value: SIRC} -- {id: SCG.SCSSEL.sel, value: SCG.SIRC} -- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -void BOARD_BootClockFRO12M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO12M */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK; -} - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF48M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFROHF48M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 48 MHz} -- {id: Slow_clock.outFreq, value: 12 MHz} -- {id: System_clock.outFreq, value: 48 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -void BOARD_BootClockFROHF48M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK; -} - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF144M ******************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFROHF144M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 144 MHz} -- {id: MAIN_clock.outFreq, value: 144 MHz} -- {id: Slow_clock.outFreq, value: 18 MHz} -- {id: System_clock.outFreq, value: 72 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true} -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} -sources: -- {id: SCG.FIRC.outFreq, value: 144 MHz} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -void BOARD_BootClockFROHF144M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(144000000U); /*!< Enable FRO HF(144MHz) output */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 2U); /*!< Set AHBCLKDIV divider to value 2 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK; -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL150M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockPLL150M -called_from_default_init: true -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 150 MHz} -- {id: PLL0_CLK_clock.outFreq, value: 150 MHz} -- {id: Slow_clock.outFreq, value: 37.5 MHz} -- {id: System_clock.outFreq, value: 150 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: PLL0_Mode, value: Normal} -- {id: RunPowerMode, value: OD} -- {id: SCGMode, value: PLL0} -- {id: SCG.PLL0M_MULT.scale, value: '50', locked: true} -- {id: SCG.PLL0SRCSEL.sel, value: SCG.FIRC_48M} -- {id: SCG.PLL0_NDIV.scale, value: '8', locked: true} -- {id: SCG.SCSSEL.sel, value: SCG.PLL0_CLK} -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -void BOARD_BootClockPLL150M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - /*!< Set up PLL0 */ - const pll_setup_t pll0Setup = { - .pllctrl = SCG_APLLCTRL_SOURCE(1U) | SCG_APLLCTRL_SELI(27U) | SCG_APLLCTRL_SELP(13U), - .pllndiv = SCG_APLLNDIV_NDIV(8U), - .pllpdiv = SCG_APLLPDIV_PDIV(1U), - .pllmdiv = SCG_APLLMDIV_MDIV(50U), - .pllRate = 150000000U - }; - CLOCK_SetPLL0Freq(&pll0Setup); /*!< Configure PLL0 to the desired values */ - CLOCK_SetPll0MonitorMode(kSCG_Pll0MonitorDisable); /* Pll0 Monitor is disabled */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kPLL0_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL0 */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKPLL150M_CORE_CLOCK; -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL100M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockPLL100M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: CLK_IN_clock.outFreq, value: 24 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: MAIN_clock.outFreq, value: 100 MHz} -- {id: PLL1_CLK_clock.outFreq, value: 100 MHz} -- {id: Slow_clock.outFreq, value: 25 MHz} -- {id: System_clock.outFreq, value: 100 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: PLL1_Mode, value: Normal} -- {id: SCGMode, value: PLL1} -- {id: SCG.PLL1M_MULT.scale, value: '100', locked: true} -- {id: SCG.PLL1_NDIV.scale, value: '6', locked: true} -- {id: SCG.PLL1_PDIV.scale, value: '4', locked: true} -- {id: SCG.SCSSEL.sel, value: SCG.PLL1_CLK} -- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} -- {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} -sources: -- {id: SCG.SOSC.outFreq, value: 24 MHz, enabled: true} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -void BOARD_BootClockPLL100M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupExtClocking(24000000U); - CLOCK_SetSysOscMonitorMode(kSCG_SysOscMonitorDisable); /* System OSC Clock Monitor is disabled */ - - /*!< Set up PLL1 */ - const pll_setup_t pll1Setup = { - .pllctrl = SCG_SPLLCTRL_SOURCE(0U) | SCG_SPLLCTRL_SELI(53U) | SCG_SPLLCTRL_SELP(26U), - .pllndiv = SCG_SPLLNDIV_NDIV(6U), - .pllpdiv = SCG_SPLLPDIV_PDIV(2U), - .pllmdiv = SCG_SPLLMDIV_MDIV(100U), - .pllRate = 100000000U - }; - CLOCK_SetPLL1Freq(&pll1Setup); /*!< Configure PLL1 to the desired values */ - CLOCK_SetPll1MonitorMode(kSCG_Pll1MonitorDisable); /* Pll1 Monitor is disabled */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kPLL1_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL1 */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKPLL100M_CORE_CLOCK; -} diff --git a/hw/bsp/mcxn/boards/frdmmcxn947/clock_config.h b/hw/bsp/mcxn/boards/frdmmcxn947/clock_config.h deleted file mode 100644 index c238a0423..000000000 --- a/hw/bsp/mcxn/boards/frdmmcxn947/clock_config.h +++ /dev/null @@ -1,177 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _CLOCK_CONFIG_H_ -#define _CLOCK_CONFIG_H_ - -#include "fsl_common.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ -#define BOARD_XTAL0_CLK_HZ 24000000U /*!< Board xtal frequency in Hz */ -#define BOARD_XTAL32K_CLK_HZ 32768U /*!< Board xtal32K frequency in Hz */ - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes default configuration of clocks. - * - */ -void BOARD_InitBootClocks(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO12M ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK 12000000U /*!< Core clock frequency: 12000000Hz */ -#define BOARD_BOOTCLOCKFRO12M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFRO12M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF48M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ -#define BOARD_BOOTCLOCKFROHF48M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFROHF48M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF144M ******************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK 144000000U /*!< Core clock frequency: 144000000Hz */ -#define BOARD_BOOTCLOCKFROHF144M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFROHF144M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL150M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKPLL150M_CORE_CLOCK 150000000U /*!< Core clock frequency: 150000000Hz */ -#define BOARD_BOOTCLOCKPLL150M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockPLL150M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL100M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKPLL100M_CORE_CLOCK 100000000U /*!< Core clock frequency: 100000000Hz */ -#define BOARD_BOOTCLOCKPLL100M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockPLL100M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.c b/hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.c deleted file mode 100644 index c33790ac5..000000000 --- a/hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.c +++ /dev/null @@ -1,143 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Pins v12.0 -processor: MCXN947 -package_id: MCXN947VDF -mcu_data: ksdk2_0 -processor_version: 0.12.3 - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -#include "fsl_common.h" -#include "fsl_port.h" -#include "pin_mux.h" - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitBootPins - * Description : Calls initialization functions. - * - * END ****************************************************************************************************************/ -void BOARD_InitBootPins(void) -{ - BOARD_InitPins(); -} - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -BOARD_InitPins: -- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'} -- pin_list: - - {pin_num: A1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P0, pin_signal: PIO1_8/WUU0_IN10/LPTMR1_ALT3/TRACE_DATA0/FC4_P0/FC5_P4/CT_INP8/SCT0_OUT2/FLEXIO0_D16/PLU_OUT0/ENET0_TXD2/I3C1_SDA/TSI0_CH17/ADC1_A8, - slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, pull_value: low, input_buffer: enable, - invert_input: normal} - - {pin_num: B1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P1, pin_signal: PIO1_9/TRACE_DATA1/FC4_P1/FC5_P5/CT_INP9/SCT0_OUT3/FLEXIO0_D17/PLU_OUT1/ENET0_TXD3/I3C1_SCL/TSI0_CH18/ADC1_A9, - slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, input_buffer: enable, invert_input: normal} - - {pin_num: B7, peripheral: GPIO0, signal: 'GPIO, 23', pin_signal: PIO0_23/WUU0_IN5/EWM0_OUT_b/FC1_P3/CT_INP3/FLEXIO0_D7/ADC0_A15/CMP2_IN2, direction: INPUT, slew_rate: fast, - open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitPins - * Description : Configures pin routing and optionally pin electrical features. - * - * END ****************************************************************************************************************/ -void BOARD_InitPins(void) -{ - /* Enables the clock for PORT0: Enables clock */ - CLOCK_EnableClock(kCLOCK_Port0); - - /* Enables the clock for PORT1: Enables clock */ - CLOCK_EnableClock(kCLOCK_Port1); - - - const port_pin_config_t port1_8_pinA1_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as FC4_P0 */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT1_8 (pin A1) is configured as FC4_P0 */ - PORT_SetPinConfig(PORT1, 8U, &port1_8_pinA1_config); - - const port_pin_config_t port1_9_pinB1_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as FC4_P1 */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT1_9 (pin B1) is configured as FC4_P1 */ - PORT_SetPinConfig(PORT1, 9U, &port1_9_pinB1_config); - - const port_pin_config_t SW2 = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as PIO0_23 */ - kPORT_MuxAlt0, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT0_23 (pin B7) is configured as PIO0_23 */ - PORT_SetPinConfig(PORT0, 23U, &SW2); -} -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.h b/hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.h deleted file mode 100644 index 40968c275..000000000 --- a/hw/bsp/mcxn/boards/frdmmcxn947/pin_mux.h +++ /dev/null @@ -1,51 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _PIN_MUX_H_ -#define _PIN_MUX_H_ - -/*! - * @addtogroup pin_mux - * @{ - */ - -/*********************************************************************************************************************** - * API - **********************************************************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif - -/*! - * @brief Calls initialization functions. - * - */ -void BOARD_InitBootPins(void); - -/*! - * @brief Configures pin routing and optionally pin electrical features. - * - */ -void BOARD_InitPins(void); - -#if defined(__cplusplus) -} -#endif - -/*! - * @} - */ -#endif /* _PIN_MUX_H_ */ - -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/hw/bsp/mcxn/boards/mcxn947brk/board.cmake b/hw/bsp/mcxn/boards/mcxn947brk/board.cmake deleted file mode 100644 index 8c3280743..000000000 --- a/hw/bsp/mcxn/boards/mcxn947brk/board.cmake +++ /dev/null @@ -1,21 +0,0 @@ -set(MCU_VARIANT MCXN947) -set(MCU_CORE MCXN947_cm33_core0) - -set(JLINK_DEVICE MCXN947_M33_0) -set(PYOCD_TARGET MCXN947) -set(NXPLINK_DEVICE MCXN947:MCXN947) - -set(PORT 1) - -function(update_board TARGET) - target_compile_definitions(${TARGET} PUBLIC - CPU_MCXN947VDF_cm33_core0 - BOARD_TUD_RHPORT=${PORT} - # port 0 is fullspeed, port 1 is highspeed - BOARD_TUD_MAX_SPEED=$ - ) - target_sources(${TARGET} PUBLIC - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/clock_config.c - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/pin_mux.c - ) -endfunction() diff --git a/hw/bsp/mcxn/boards/mcxn947brk/board.h b/hw/bsp/mcxn/boards/mcxn947brk/board.h deleted file mode 100644 index eae98bfa7..000000000 --- a/hw/bsp/mcxn/boards/mcxn947brk/board.h +++ /dev/null @@ -1,66 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2021, Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#ifndef BOARD_H_ -#define BOARD_H_ - -#ifdef __cplusplus - extern "C" { -#endif - -// LED -#define LED_GPIO GPIO3 -#define LED_CLK kCLOCK_Gpio3 -#define LED_PIN 4 // red -#define LED_STATE_ON 0 - -// WAKE button (Dummy, use unused pin -#define BUTTON_GPIO GPIO0 -#define BUTTON_CLK kCLOCK_Gpio0 -#define BUTTON_PIN 6 -#define BUTTON_STATE_ACTIVE 0 - -// UART -#define UART_DEV LPUART4 - -static inline void board_uart_init_clock(void) { - /* attach FRO 12M to FLEXCOMM4 */ - CLOCK_SetClkDiv(kCLOCK_DivFlexcom4Clk, 1u); - CLOCK_AttachClk(kFRO12M_to_FLEXCOMM4); - RESET_ClearPeripheralReset(kFC4_RST_SHIFT_RSTn); -} - -//#define UART_RX_PINMUX 0, 24, IOCON_PIO_DIG_FUNC1_EN -//#define UART_TX_PINMUX 0, 25, IOCON_PIO_DIG_FUNC1_EN - -// XTAL -#define XTAL0_CLK_HZ (24 * 1000 * 1000U) - -#ifdef __cplusplus - } -#endif - -#endif diff --git a/hw/bsp/mcxn/boards/mcxn947brk/board.mk b/hw/bsp/mcxn/boards/mcxn947brk/board.mk deleted file mode 100644 index aaad5e73e..000000000 --- a/hw/bsp/mcxn/boards/mcxn947brk/board.mk +++ /dev/null @@ -1,11 +0,0 @@ -MCU_VARIANT = MCXN947 -MCU_CORE = MCXN947_cm33_core0 -PORT ?= 1 - -CFLAGS += -DCPU_MCXN947VDF_cm33_core0 - -JLINK_DEVICE = MCXN947_M33_0 -PYOCD_TARGET = MCXN947 - -# flash using pyocd -flash: flash-jlink diff --git a/hw/bsp/mcxn/boards/mcxn947brk/clock_config.c b/hw/bsp/mcxn/boards/mcxn947brk/clock_config.c deleted file mode 100644 index 37d2b4dfc..000000000 --- a/hw/bsp/mcxn/boards/mcxn947brk/clock_config.c +++ /dev/null @@ -1,338 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ -/* - * How to setup clock using clock driver functions: - * - * 1. Setup clock sources. - * - * 2. Set up wait states of the flash. - * - * 3. Set up all dividers. - * - * 4. Set up all selectors to provide selected clocks. - * - */ - -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Clocks v10.0 -processor: MCXN947 -package_id: MCXN947VDF -mcu_data: ksdk2_0 -processor_version: 0.12.3 -board: MCX-N9XX-EVK - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -#include "clock_config.h" -#include "fsl_clock.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ - -/******************************************************************************* - * Variables - ******************************************************************************/ -/* System clock frequency. */ -// extern uint32_t SystemCoreClock; - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ -void BOARD_InitBootClocks(void) -{ - BOARD_BootClockPLL150M(); -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO12M ********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFRO12M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: MAIN_clock.outFreq, value: 12 MHz} -- {id: Slow_clock.outFreq, value: 3 MHz} -- {id: System_clock.outFreq, value: 12 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SCGMode, value: SIRC} -- {id: SCG.SCSSEL.sel, value: SCG.SIRC} -- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -void BOARD_BootClockFRO12M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO12M_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO12M */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFRO12M_CORE_CLOCK; -} - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF48M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFROHF48M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 48 MHz} -- {id: Slow_clock.outFreq, value: 12 MHz} -- {id: System_clock.outFreq, value: 48 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -void BOARD_BootClockFROHF48M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK; -} - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF144M ******************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockFROHF144M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 144 MHz} -- {id: MAIN_clock.outFreq, value: 144 MHz} -- {id: Slow_clock.outFreq, value: 18 MHz} -- {id: System_clock.outFreq, value: 72 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: SYSCON.AHBCLKDIV.scale, value: '2', locked: true} -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} -sources: -- {id: SCG.FIRC.outFreq, value: 144 MHz} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -void BOARD_BootClockFROHF144M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(144000000U); /*!< Enable FRO HF(144MHz) output */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kFRO_HF_to_MAIN_CLK); /*!< Switch MAIN_CLK to FRO_HF */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 2U); /*!< Set AHBCLKDIV divider to value 2 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK; -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL150M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockPLL150M -called_from_default_init: true -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: FRO_HF_clock.outFreq, value: 48 MHz} -- {id: MAIN_clock.outFreq, value: 150 MHz} -- {id: PLL0_CLK_clock.outFreq, value: 150 MHz} -- {id: Slow_clock.outFreq, value: 37.5 MHz} -- {id: System_clock.outFreq, value: 150 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: PLL0_Mode, value: Normal} -- {id: RunPowerMode, value: OD} -- {id: SCGMode, value: PLL0} -- {id: SCG.PLL0M_MULT.scale, value: '50', locked: true} -- {id: SCG.PLL0SRCSEL.sel, value: SCG.FIRC_48M} -- {id: SCG.PLL0_NDIV.scale, value: '8', locked: true} -- {id: SCG.SCSSEL.sel, value: SCG.PLL0_CLK} -- {id: SYSCON.FLEXCAN0CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FLEXCAN1CLKSEL.sel, value: NO_CLOCK} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -void BOARD_BootClockPLL150M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupFROHFClocking(48000000U); /*!< Enable FRO HF(48MHz) output */ - - /*!< Set up PLL0 */ - const pll_setup_t pll0Setup = { - .pllctrl = SCG_APLLCTRL_SOURCE(1U) | SCG_APLLCTRL_SELI(27U) | SCG_APLLCTRL_SELP(13U), - .pllndiv = SCG_APLLNDIV_NDIV(8U), - .pllpdiv = SCG_APLLPDIV_PDIV(1U), - .pllmdiv = SCG_APLLMDIV_MDIV(50U), - .pllRate = 150000000U - }; - CLOCK_SetPLL0Freq(&pll0Setup); /*!< Configure PLL0 to the desired values */ - CLOCK_SetPll0MonitorMode(kSCG_Pll0MonitorDisable); /* Pll0 Monitor is disabled */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kPLL0_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL0 */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKPLL150M_CORE_CLOCK; -} - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL100M ********************* - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockPLL100M -outputs: -- {id: CLK_144M_clock.outFreq, value: 144 MHz} -- {id: CLK_48M_clock.outFreq, value: 48 MHz} -- {id: CLK_IN_clock.outFreq, value: 24 MHz} -- {id: FRO_12M_clock.outFreq, value: 12 MHz} -- {id: MAIN_clock.outFreq, value: 100 MHz} -- {id: PLL1_CLK_clock.outFreq, value: 100 MHz} -- {id: Slow_clock.outFreq, value: 25 MHz} -- {id: System_clock.outFreq, value: 100 MHz} -- {id: gdet_clock.outFreq, value: 48 MHz} -- {id: trng_clock.outFreq, value: 48 MHz} -settings: -- {id: PLL1_Mode, value: Normal} -- {id: SCGMode, value: PLL1} -- {id: SCG.PLL1M_MULT.scale, value: '100', locked: true} -- {id: SCG.PLL1_NDIV.scale, value: '6', locked: true} -- {id: SCG.PLL1_PDIV.scale, value: '4', locked: true} -- {id: SCG.SCSSEL.sel, value: SCG.PLL1_CLK} -- {id: SCG_FIRCCSR_FIRCEN_CFG, value: Disabled} -- {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled} -- {id: SYSCON.FREQMEREFCLKSEL.sel, value: SYSCON.evtg_out0a} -- {id: SYSCON.FREQMETARGETCLKSEL.sel, value: SYSCON.evtg_out0a} -sources: -- {id: SCG.SOSC.outFreq, value: 24 MHz, enabled: true} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -/******************************************************************************* - * Code for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -void BOARD_BootClockPLL100M(void) -{ - /*!< Enable SCG clock */ - CLOCK_EnableClock(kCLOCK_Scg); - - CLOCK_SetupExtClocking(24000000U); - CLOCK_SetSysOscMonitorMode(kSCG_SysOscMonitorDisable); /* System OSC Clock Monitor is disabled */ - - /*!< Set up PLL1 */ - const pll_setup_t pll1Setup = { - .pllctrl = SCG_SPLLCTRL_SOURCE(0U) | SCG_SPLLCTRL_SELI(53U) | SCG_SPLLCTRL_SELP(26U), - .pllndiv = SCG_SPLLNDIV_NDIV(6U), - .pllpdiv = SCG_SPLLPDIV_PDIV(2U), - .pllmdiv = SCG_SPLLMDIV_MDIV(100U), - .pllRate = 100000000U - }; - CLOCK_SetPLL1Freq(&pll1Setup); /*!< Configure PLL1 to the desired values */ - CLOCK_SetPll1MonitorMode(kSCG_Pll1MonitorDisable); /* Pll1 Monitor is disabled */ - - /*!< Set up clock selectors - Attach clocks to the peripheries */ - CLOCK_AttachClk(kPLL1_to_MAIN_CLK); /*!< Switch MAIN_CLK to PLL1 */ - - /*!< Set up dividers */ - CLOCK_SetClkDiv(kCLOCK_DivAhbClk, 1U); /*!< Set AHBCLKDIV divider to value 1 */ - - /* Set SystemCoreClock variable */ - SystemCoreClock = BOARD_BOOTCLOCKPLL100M_CORE_CLOCK; -} diff --git a/hw/bsp/mcxn/boards/mcxn947brk/clock_config.h b/hw/bsp/mcxn/boards/mcxn947brk/clock_config.h deleted file mode 100644 index c238a0423..000000000 --- a/hw/bsp/mcxn/boards/mcxn947brk/clock_config.h +++ /dev/null @@ -1,177 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _CLOCK_CONFIG_H_ -#define _CLOCK_CONFIG_H_ - -#include "fsl_common.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ -#define BOARD_XTAL0_CLK_HZ 24000000U /*!< Board xtal frequency in Hz */ -#define BOARD_XTAL32K_CLK_HZ 32768U /*!< Board xtal32K frequency in Hz */ - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes default configuration of clocks. - * - */ -void BOARD_InitBootClocks(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockFRO12M ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFRO12M_CORE_CLOCK 12000000U /*!< Core clock frequency: 12000000Hz */ -#define BOARD_BOOTCLOCKFRO12M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFRO12M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFRO12M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF48M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFROHF48M_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ -#define BOARD_BOOTCLOCKFROHF48M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFROHF48M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFROHF48M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************* Configuration BOARD_BootClockFROHF144M ******************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKFROHF144M_CORE_CLOCK 144000000U /*!< Core clock frequency: 144000000Hz */ -#define BOARD_BOOTCLOCKFROHF144M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockFROHF144M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockFROHF144M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL150M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKPLL150M_CORE_CLOCK 150000000U /*!< Core clock frequency: 150000000Hz */ -#define BOARD_BOOTCLOCKPLL150M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockPLL150M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockPLL150M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ******************** Configuration BOARD_BootClockPLL100M ********************* - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKPLL100M_CORE_CLOCK 100000000U /*!< Core clock frequency: 100000000Hz */ -#define BOARD_BOOTCLOCKPLL100M_ROSC_CLOCK 0U /*!< ROSC clock frequency: 0Hz */ - - -/******************************************************************************* - * API for BOARD_BootClockPLL100M configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockPLL100M(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/mcxn/boards/mcxn947brk/pin_mux.c b/hw/bsp/mcxn/boards/mcxn947brk/pin_mux.c deleted file mode 100644 index acc2f3e45..000000000 --- a/hw/bsp/mcxn/boards/mcxn947brk/pin_mux.c +++ /dev/null @@ -1,141 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Pins v12.0 -processor: MCXN947 -package_id: MCXN947VDF -mcu_data: ksdk2_0 -processor_version: 0.12.3 - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -#include "fsl_common.h" -#include "fsl_port.h" -#include "pin_mux.h" - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitBootPins - * Description : Calls initialization functions. - * - * END ****************************************************************************************************************/ -void BOARD_InitBootPins(void) -{ - BOARD_InitPins(); -} - -/* clang-format off */ -/* - * TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -BOARD_InitPins: -- options: {callFromInitBoot: 'true', coreID: cm33_core0, enableClock: 'true'} -- pin_list: - - {pin_num: A1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P0, pin_signal: PIO1_8/WUU0_IN10/LPTMR1_ALT3/TRACE_DATA0/FC4_P0/FC5_P4/CT_INP8/SCT0_OUT2/FLEXIO0_D16/PLU_OUT0/ENET0_TXD2/I3C1_SDA/TSI0_CH17/ADC1_A8, - slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, pull_value: low, input_buffer: enable, - invert_input: normal} - - {pin_num: B1, peripheral: LPFlexcomm4, signal: LPFLEXCOMM_P1, pin_signal: PIO1_9/TRACE_DATA1/FC4_P1/FC5_P5/CT_INP9/SCT0_OUT3/FLEXIO0_D17/PLU_OUT1/ENET0_TXD3/I3C1_SCL/TSI0_CH18/ADC1_A9, - slew_rate: fast, open_drain: disable, drive_strength: low, pull_select: down, pull_enable: disable, passive_filter: disable, input_buffer: enable, invert_input: normal} - - {pin_num: F14, peripheral: GPIO3, signal: 'GPIO, 4', pin_signal: PIO3_4/FC7_P2/CT_INP18/PWM0_X2/FLEXIO0_D12/SIM1_CLK, slew_rate: fast, open_drain: disable, drive_strength: low, - pull_select: down, pull_enable: disable, input_buffer: enable, invert_input: normal} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS *********** - */ -/* clang-format on */ - -/* FUNCTION ************************************************************************************************************ - * - * Function Name : BOARD_InitPins - * Description : Configures pin routing and optionally pin electrical features. - * - * END ****************************************************************************************************************/ -void BOARD_InitPins(void) -{ - /* Enables the clock for PORT1: Enables clock */ - CLOCK_EnableClock(kCLOCK_Port1); - /* Enables the clock for PORT3: Enables clock */ - CLOCK_EnableClock(kCLOCK_Port3); - - const port_pin_config_t port1_8_pinA1_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as FC4_P0 */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT1_8 (pin A1) is configured as FC4_P0 */ - PORT_SetPinConfig(PORT1, 8U, &port1_8_pinA1_config); - - const port_pin_config_t port1_9_pinB1_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as FC4_P1 */ - kPORT_MuxAlt2, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT1_9 (pin B1) is configured as FC4_P1 */ - PORT_SetPinConfig(PORT1, 9U, &port1_9_pinB1_config); - - const port_pin_config_t port3_4_pinF14_config = {/* Internal pull-up/down resistor is disabled */ - kPORT_PullDisable, - /* Low internal pull resistor value is selected. */ - kPORT_LowPullResistor, - /* Fast slew rate is configured */ - kPORT_FastSlewRate, - /* Passive input filter is disabled */ - kPORT_PassiveFilterDisable, - /* Open drain output is disabled */ - kPORT_OpenDrainDisable, - /* Low drive strength is configured */ - kPORT_LowDriveStrength, - /* Pin is configured as PIO3_4 */ - kPORT_MuxAlt0, - /* Digital input enabled */ - kPORT_InputBufferEnable, - /* Digital input is not inverted */ - kPORT_InputNormal, - /* Pin Control Register fields [15:0] are not locked */ - kPORT_UnlockRegister}; - /* PORT3_4 (pin F14) is configured as PIO3_4 */ - PORT_SetPinConfig(PORT3, 4U, &port3_4_pinF14_config); -} -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/hw/bsp/mcxn/boards/mcxn947brk/pin_mux.h b/hw/bsp/mcxn/boards/mcxn947brk/pin_mux.h deleted file mode 100644 index 40968c275..000000000 --- a/hw/bsp/mcxn/boards/mcxn947brk/pin_mux.h +++ /dev/null @@ -1,51 +0,0 @@ -/* - * Copyright 2022 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _PIN_MUX_H_ -#define _PIN_MUX_H_ - -/*! - * @addtogroup pin_mux - * @{ - */ - -/*********************************************************************************************************************** - * API - **********************************************************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif - -/*! - * @brief Calls initialization functions. - * - */ -void BOARD_InitBootPins(void); - -/*! - * @brief Configures pin routing and optionally pin electrical features. - * - */ -void BOARD_InitPins(void); - -#if defined(__cplusplus) -} -#endif - -/*! - * @} - */ -#endif /* _PIN_MUX_H_ */ - -/*********************************************************************************************************************** - * EOF - **********************************************************************************************************************/ diff --git a/hw/bsp/mcxn/debug.jlinkscript b/hw/bsp/mcxn/debug.jlinkscript deleted file mode 100644 index fd8bcffef..000000000 --- a/hw/bsp/mcxn/debug.jlinkscript +++ /dev/null @@ -1,5 +0,0 @@ -int SetupTarget(void) { - JLINK_ExecCommand("SetRTTSearchRanges 0x20000000 0x40000"); - - return 0; -} diff --git a/hw/bsp/mcxn/family.c b/hw/bsp/mcxn/family.c deleted file mode 100644 index 8672ca63f..000000000 --- a/hw/bsp/mcxn/family.c +++ /dev/null @@ -1,245 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2018, hathach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#include "bsp/board_api.h" -#include "fsl_device_registers.h" -#include "fsl_gpio.h" -#include "fsl_lpuart.h" -#include "board.h" - -#include "pin_mux.h" -#include "clock_config.h" - -#ifdef BOARD_TUD_RHPORT - #define PORT_SUPPORT_DEVICE(_n) (BOARD_TUD_RHPORT == _n) -#else - #define PORT_SUPPORT_DEVICE(_n) 0 -#endif - -#ifdef BOARD_TUH_RHPORT - #define PORT_SUPPORT_HOST(_n) (BOARD_TUH_RHPORT == _n) -#else - #define PORT_SUPPORT_HOST(_n) 0 -#endif - -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ - -//--------------------------------------------------------------------+ -// Forward USB interrupt events to TinyUSB IRQ Handler -//--------------------------------------------------------------------+ -void USB0_FS_IRQHandler(void) -{ - tud_int_handler(0); -} - -void USB1_HS_IRQHandler(void) -{ - tud_int_handler(1); -} - -void board_init(void) -{ - BOARD_InitPins(); - BOARD_InitBootClocks(); - CLOCK_SetupExtClocking(XTAL0_CLK_HZ); - - // 1ms tick timer - SysTick_Config(SystemCoreClock / 1000); - -#if CFG_TUSB_OS == OPT_OS_FREERTOS - // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(USB1_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); -#endif - - // LED - CLOCK_EnableClock(LED_CLK); - gpio_pin_config_t led_config = { - kGPIO_DigitalOutput, - 0, - }; - GPIO_PinInit(LED_GPIO,LED_PIN, &led_config); - board_led_write(0); - -#ifdef NEOPIXEL_PIN - // Neopixel - static uint32_t pixelData[NEOPIXEL_NUMBER]; - IOCON_PinMuxSet(IOCON, NEOPIXEL_PORT, NEOPIXEL_PIN, IOCON_PIO_DIG_FUNC4_EN); - - sctpix_init(NEOPIXEL_TYPE); - sctpix_addCh(NEOPIXEL_CH, pixelData, NEOPIXEL_NUMBER); - sctpix_setPixel(NEOPIXEL_CH, 0, 0x100010); - sctpix_setPixel(NEOPIXEL_CH, 1, 0x100010); - sctpix_show(); -#endif - - // Button -#ifdef BUTTON_GPIO - CLOCK_EnableClock(BUTTON_CLK); - gpio_pin_config_t const button_config = { kGPIO_DigitalInput, 0}; - GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); -#endif - -#ifdef UART_DEV - // UART -// IOCON_PinMuxSet(IOCON, UART_RX_PINMUX); -// IOCON_PinMuxSet(IOCON, UART_TX_PINMUX); - - // Enable UART when debug log is on - board_uart_init_clock(); - - lpuart_config_t uart_config; - LPUART_GetDefaultConfig(&uart_config); - uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE; - uart_config.enableTx = true; - uart_config.enableRx = true; - LPUART_Init(UART_DEV, &uart_config, 12000000u); -#endif - - // USB VBUS - /* PORT0 PIN22 configured as USB0_VBUS */ - -#if PORT_SUPPORT_DEVICE(0) - // Port0 is Full Speed - - CLOCK_AttachClk(kCLK_48M_to_USB0); - CLOCK_EnableClock(kCLOCK_Usb0Ram); - CLOCK_EnableClock(kCLOCK_Usb0Fs); - CLOCK_EnableUsbfsClock(); -#endif - -#if PORT_SUPPORT_DEVICE(1) - // Port1 is High Speed - - // Power - SPC0->ACTIVE_VDELAY = 0x0500; - /* Change the power DCDC to 1.8v (By default, DCDC is 1.8V), CORELDO to 1.1v (By default, CORELDO is 1.0V) */ - SPC0->ACTIVE_CFG &= ~SPC_ACTIVE_CFG_CORELDO_VDD_DS_MASK; - SPC0->ACTIVE_CFG |= SPC_ACTIVE_CFG_DCDC_VDD_LVL(0x3) | SPC_ACTIVE_CFG_CORELDO_VDD_LVL(0x3) | - SPC_ACTIVE_CFG_SYSLDO_VDD_DS_MASK | SPC_ACTIVE_CFG_DCDC_VDD_DS(0x2u); - /* Wait until it is done */ - while (SPC0->SC & SPC_SC_BUSY_MASK) {} - if (0u == (SCG0->LDOCSR & SCG_LDOCSR_LDOEN_MASK)) { - SCG0->TRIM_LOCK = 0x5a5a0001U; - SCG0->LDOCSR |= SCG_LDOCSR_LDOEN_MASK; - /* wait LDO ready */ - while (0U == (SCG0->LDOCSR & SCG_LDOCSR_VOUT_OK_MASK)); - } - SYSCON->AHBCLKCTRLSET[2] |= SYSCON_AHBCLKCTRL2_USB_HS_MASK | SYSCON_AHBCLKCTRL2_USB_HS_PHY_MASK; - SCG0->SOSCCFG &= ~(SCG_SOSCCFG_RANGE_MASK | SCG_SOSCCFG_EREFS_MASK); - /* xtal = 20 ~ 30MHz */ - SCG0->SOSCCFG = (1U << SCG_SOSCCFG_RANGE_SHIFT) | (1U << SCG_SOSCCFG_EREFS_SHIFT); - SCG0->SOSCCSR |= SCG_SOSCCSR_SOSCEN_MASK; - while (1) { - if (SCG0->SOSCCSR & SCG_SOSCCSR_SOSCVLD_MASK) { - break; - } - } - - // Clock - SYSCON->CLOCK_CTRL |= SYSCON_CLOCK_CTRL_CLKIN_ENA_MASK | SYSCON_CLOCK_CTRL_CLKIN_ENA_FM_USBH_LPT_MASK; - CLOCK_EnableClock(kCLOCK_UsbHs); - CLOCK_EnableClock(kCLOCK_UsbHsPhy); - CLOCK_EnableUsbhsPhyPllClock(kCLOCK_Usbphy480M, 24000000U); - CLOCK_EnableUsbhsClock(); - - // USB PHY -#if ((!(defined FSL_FEATURE_SOC_CCM_ANALOG_COUNT)) && (!(defined FSL_FEATURE_SOC_ANATOP_COUNT))) - USBPHY->TRIM_OVERRIDE_EN = 0x001fU; /* override IFR value */ -#endif - - // Enable PHY support for Low speed device + LS via FS Hub - USBPHY->CTRL |= USBPHY_CTRL_SET_ENUTMILEVEL2_MASK | USBPHY_CTRL_SET_ENUTMILEVEL3_MASK; - - // Enable all power for normal operation - USBPHY->PWD = 0; - - // TX Timing - uint32_t phytx = USBPHY->TX; - phytx &= ~(USBPHY_TX_D_CAL_MASK | USBPHY_TX_TXCAL45DM_MASK | USBPHY_TX_TXCAL45DP_MASK); - phytx |= USBPHY_TX_D_CAL(0x04) | USBPHY_TX_TXCAL45DP(0x07) | USBPHY_TX_TXCAL45DM(0x07); - //phytx |= USBPHY_TX_D_CAL(0x0C) | USBPHY_TX_TXCAL45DP(0x06) | USBPHY_TX_TXCAL45DM(0x06); - USBPHY->TX = phytx; -#endif -} - -//--------------------------------------------------------------------+ -// Board porting API -//--------------------------------------------------------------------+ - -void board_led_write(bool state) -{ - GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); - -#ifdef NEOPIXEL_PIN - if (state) { - sctpix_setPixel(NEOPIXEL_CH, 0, 0x100000); - sctpix_setPixel(NEOPIXEL_CH, 1, 0x101010); - } else { - sctpix_setPixel(NEOPIXEL_CH, 0, 0x001000); - sctpix_setPixel(NEOPIXEL_CH, 1, 0x000010); - } - sctpix_show(); -#endif -} - -uint32_t board_button_read(void) -{ -#ifdef BUTTON_GPIO - return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); -#endif -} - -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; - return 0; -} - -int board_uart_write(void const * buf, int len) -{ -#ifdef UART_DEV - LPUART_WriteBlocking(UART_DEV, (uint8_t const *) buf, len); - return len; -#else - (void) buf; (void) len; - return 0; -#endif -} - -#if CFG_TUSB_OS == OPT_OS_NONE -volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ - system_ticks++; -} - -uint32_t board_millis(void) -{ - return system_ticks; -} -#endif diff --git a/hw/bsp/mcxn/family.cmake b/hw/bsp/mcxn/family.cmake deleted file mode 100644 index 13d1d44ef..000000000 --- a/hw/bsp/mcxn/family.cmake +++ /dev/null @@ -1,110 +0,0 @@ -include_guard() - -if (NOT BOARD) - message(FATAL_ERROR "BOARD not specified") -endif () - -set(SDK_DIR ${TOP}/hw/mcu/nxp/mcux-sdk) -set(CMSIS_DIR ${TOP}/lib/CMSIS_5) - -# include board specific -include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) - -# toolchain set up -set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor") -set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOLCHAIN}.cmake) - -set(FAMILY_MCUS MCXN9 CACHE INTERNAL "") - - -#------------------------------------ -# BOARD_TARGET -#------------------------------------ -# only need to be built ONCE for all examples -function(add_board_target BOARD_TARGET) - if (NOT TARGET ${BOARD_TARGET}) - add_library(${BOARD_TARGET} STATIC - # external driver - #lib/sct_neopixel/sct_neopixel.c - - # driver - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_gpio.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_common_arm.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpuart.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpflexcomm.c - # mcu - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_reset.c - ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_CORE}.c - ) - # target_compile_definitions(${BOARD_TARGET} PUBLIC - # ) - target_include_directories(${BOARD_TARGET} PUBLIC - # driver - # mcu - ${CMSIS_DIR}/CMSIS/Core/Include - ${SDK_DIR}/devices/${MCU_VARIANT} - ${SDK_DIR}/devices/${MCU_VARIANT}/drivers - ) - - update_board(${BOARD_TARGET}) - - if (CMAKE_C_COMPILER_ID STREQUAL "GNU") - target_sources(${BOARD_TARGET} PUBLIC - ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_CORE}.S - ) - target_link_options(${BOARD_TARGET} PUBLIC - # linker file - "LINKER:--script=${SDK_DIR}/devices/${MCU_VARIANT}/gcc/${MCU_CORE}_flash.ld" - # nanolib - --specs=nosys.specs - --specs=nano.specs - ) - elseif (CMAKE_C_COMPILER_ID STREQUAL "IAR") - target_link_options(${BOARD_TARGET} PUBLIC - "LINKER:--config=${LD_FILE_IAR}" - ) - endif () - endif () -endfunction() - - -#------------------------------------ -# Functions -#------------------------------------ -function(family_configure_example TARGET RTOS) - family_configure_common(${TARGET} ${RTOS}) - - # Board target - add_board_target(board_${BOARD}) - - #---------- Port Specific ---------- - # These files are built for each example since it depends on example's tusb_config.h - target_sources(${TARGET} PUBLIC - # BSP - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/family.c - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../board.c - ) - target_include_directories(${TARGET} PUBLIC - # family, hw, board - ${CMAKE_CURRENT_FUNCTION_LIST_DIR} - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/../../ - ${CMAKE_CURRENT_FUNCTION_LIST_DIR}/boards/${BOARD} - ) - - # Add TinyUSB target and port source - family_add_tinyusb(${TARGET} OPT_MCU_MCXN9 ${RTOS}) - target_sources(${TARGET}-tinyusb PUBLIC - # TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS - ${TOP}/src/portable/chipidea/$ - ) - target_link_libraries(${TARGET}-tinyusb PUBLIC board_${BOARD}) - - # Link dependencies - target_link_libraries(${TARGET} PUBLIC board_${BOARD} ${TARGET}-tinyusb) - - # Flashing - family_flash_jlink(${TARGET}) - #family_flash_nxplink(${TARGET}) - #family_flash_pyocd(${TARGET}) -endfunction() diff --git a/hw/bsp/mcxn/family.mk b/hw/bsp/mcxn/family.mk deleted file mode 100644 index 526effdfb..000000000 --- a/hw/bsp/mcxn/family.mk +++ /dev/null @@ -1,51 +0,0 @@ -UF2_FAMILY_ID = 0x2abc77ec -SDK_DIR = hw/mcu/nxp/mcux-sdk - -DEPS_SUBMODULES += $(SDK_DIR) lib/CMSIS_5 - -include $(TOP)/$(BOARD_PATH)/board.mk -CPU_CORE ?= cortex-m33 - -# Default to Highspeed PORT1 -PORT ?= 1 - -CFLAGS += \ - -flto \ - -DCFG_TUSB_MCU=OPT_MCU_MCXN9 \ - -DBOARD_TUD_RHPORT=$(PORT) \ - -# mcu driver cause following warnings -CFLAGS += -Wno-error=unused-parameter -Wno-error=old-style-declaration - -LDFLAGS_GCC += -specs=nosys.specs -specs=nano.specs - -# All source paths should be relative to the top level. -LD_FILE ?= $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/$(MCU_CORE)_flash.ld - -# TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS -ifeq ($(PORT), 1) - $(info "PORT1 High Speed") - CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_HIGH_SPEED - SRC_C += src/portable/chipidea/ci_hs/dcd_ci_hs.c -else - $(info "PORT0 Full Speed") - CFLAGS += -DBOARD_TUD_MAX_SPEED=OPT_MODE_FULL_SPEED - SRC_C += src/portable/chipidea/ci_fs/dcd_ci_fs.c -endif - -SRC_C += \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/system_$(MCU_CORE).c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_clock.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_reset.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_gpio.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_common_arm.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpflexcomm.c \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpuart.c \ - -INC += \ - $(TOP)/$(BOARD_PATH) \ - $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ - $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT) \ - $(TOP)/$(SDK_DIR)/devices/$(MCU_VARIANT)/drivers \ - -SRC_S += $(SDK_DIR)/devices/$(MCU_VARIANT)/gcc/startup_$(MCU_CORE).S diff --git a/src/common/tusb_mcu.h b/src/common/tusb_mcu.h index 21ae3a71e..7b6da5f59 100644 --- a/src/common/tusb_mcu.h +++ b/src/common/tusb_mcu.h @@ -100,10 +100,10 @@ #define TUP_DCD_ENDPOINT_MAX 8 #define TUP_RHPORT_HIGHSPEED 1 -#elif TU_CHECK_MCU(OPT_MCU_MCXA) +#elif TU_CHECK_MCU(OPT_MCU_MCXA15) // USB0 is chipidea FS #define TUP_USBIP_CHIPIDEA_FS - #define TUP_USBIP_CHIPIDEA_FS_MCXA + #define TUP_USBIP_CHIPIDEA_FS_MCX #define TUP_DCD_ENDPOINT_MAX 16 diff --git a/src/portable/chipidea/ci_fs/ci_fs_mcx.h b/src/portable/chipidea/ci_fs/ci_fs_mcx.h index 3bfcd398e..bf88df0f4 100644 --- a/src/portable/chipidea/ci_fs/ci_fs_mcx.h +++ b/src/portable/chipidea/ci_fs/ci_fs_mcx.h @@ -29,19 +29,30 @@ #include "fsl_device_registers.h" -#define CI_FS_REG(_port) ((ci_fs_regs_t*) USBFS0_BASE) +#if CFG_TUSB_MCU == OPT_MCU_MCXN9 + #define CI_FS_REG(_port) ((ci_fs_regs_t*) USBFS0_BASE) + #define USB0_IRQN USB0_FS_IRQn + +#elif CFG_TUSB_MCU == OPT_MCU_MCXA15 + #define CI_FS_REG(_port) ((ci_fs_regs_t*) USB0_BASE) + #define USB0_IRQN USB0_IRQn + +#else + #error "MCU is not supported" +#endif + #define CI_REG CI_FS_REG(0) void dcd_int_enable(uint8_t rhport) { (void) rhport; - NVIC_EnableIRQ(USB0_FS_IRQn); + NVIC_EnableIRQ(USB0_IRQN); } void dcd_int_disable(uint8_t rhport) { (void) rhport; - NVIC_DisableIRQ(USB0_FS_IRQn); + NVIC_DisableIRQ(USB0_IRQN); } #endif diff --git a/src/portable/chipidea/ci_fs/ci_fs_mcxa.h b/src/portable/chipidea/ci_fs/ci_fs_mcxa.h deleted file mode 100644 index 81786efdf..000000000 --- a/src/portable/chipidea/ci_fs/ci_fs_mcxa.h +++ /dev/null @@ -1,47 +0,0 @@ -/* - * The MIT License (MIT) - * - * Copyright (c) 2023 Ha Thach (tinyusb.org) - * - * Permission is hereby granted, free of charge, to any person obtaining a copy - * of this software and associated documentation files (the "Software"), to deal - * in the Software without restriction, including without limitation the rights - * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell - * copies of the Software, and to permit persons to whom the Software is - * furnished to do so, subject to the following conditions: - * - * The above copyright notice and this permission notice shall be included in - * all copies or substantial portions of the Software. - * - * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR - * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, - * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE - * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER - * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, - * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN - * THE SOFTWARE. - * - * This file is part of the TinyUSB stack. - */ - -#ifndef _CI_FS_MCXA_H -#define _CI_FS_MCXA_H - -#include "fsl_device_registers.h" - -#define CI_FS_REG(_port) ((ci_fs_regs_t*) USB0_BASE) -#define CI_REG CI_FS_REG(0) - -void dcd_int_enable(uint8_t rhport) -{ - (void) rhport; - NVIC_EnableIRQ(USB0_IRQn); -} - -void dcd_int_disable(uint8_t rhport) -{ - (void) rhport; - NVIC_DisableIRQ(USB0_IRQn); -} - -#endif diff --git a/src/portable/chipidea/ci_fs/dcd_ci_fs.c b/src/portable/chipidea/ci_fs/dcd_ci_fs.c index 08e73711f..9327e09d8 100644 --- a/src/portable/chipidea/ci_fs/dcd_ci_fs.c +++ b/src/portable/chipidea/ci_fs/dcd_ci_fs.c @@ -35,8 +35,6 @@ #include "ci_fs_kinetis.h" #elif defined(TUP_USBIP_CHIPIDEA_FS_MCX) #include "ci_fs_mcx.h" -#elif defined(TUP_USBIP_CHIPIDEA_FS_MCXA) - #include "ci_fs_mcxa.h" #else #error "MCU is not supported" #endif diff --git a/src/tusb_option.h b/src/tusb_option.h index fe9c44e96..e46e641f3 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -175,7 +175,7 @@ // NXP LPC MCX #define OPT_MCU_MCXN9 2300 ///< NXP MCX N9 Series -#define OPT_MCU_MCXA 2301 ///< NXP MCX A Series +#define OPT_MCU_MCXA15 2301 ///< NXP MCX A15 Series // Check if configured MCU is one of listed // Apply _TU_CHECK_MCU with || as separator to list of input -- cgit v1.3.1 From ec91660119c6ce4ccc6aa011f2c6cc9869ab9410 Mon Sep 17 00:00:00 2001 From: Jerry Palacios Date: Thu, 22 Feb 2024 16:11:23 -0600 Subject: Revert "Merge branch 'hathach:master' into MCX" This reverts commit 6afd4a57896f9c9e794de3ab6eabc73d18be4bd0, reversing changes made to 5c14bd13da211ff2679115b0dba96ac80c1a516c. --- examples/device/cdc_msc_freertos/src/main.c | 51 +-- hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk | 3 + .../boards/frdm_k32l2a4s/clock_config.c | 491 --------------------- .../boards/frdm_k32l2a4s/clock_config.h | 164 ------- hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk | 3 + .../boards/frdm_k32l2b/clock_config.c | 220 --------- .../boards/frdm_k32l2b/clock_config.h | 110 ----- hw/bsp/nrf/boards/pca10095/board.cmake | 3 - hw/bsp/nrf/boards/pca10095/board.h | 4 +- hw/bsp/nrf/boards/pca10095/board.mk | 3 - hw/bsp/nrf/family.c | 1 - src/class/msc/msc_device.c | 2 +- src/class/video/video.h | 6 +- src/class/video/video_device.c | 1 - src/common/tusb_debug.h | 3 +- src/common/tusb_fifo.c | 1 - src/device/usbd.c | 1 + src/host/usbh.c | 22 +- src/host/usbh_pvt.h | 6 +- src/portable/nordic/nrf5x/dcd_nrf5x.c | 8 +- src/portable/ohci/ohci.h | 2 +- 21 files changed, 52 insertions(+), 1053 deletions(-) delete mode 100644 hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/clock_config.c delete mode 100644 hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/clock_config.h delete mode 100644 hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/clock_config.c delete mode 100644 hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/clock_config.h (limited to 'src/portable') diff --git a/examples/device/cdc_msc_freertos/src/main.c b/examples/device/cdc_msc_freertos/src/main.c index e94e8eaec..1dadc4513 100644 --- a/examples/device/cdc_msc_freertos/src/main.c +++ b/examples/device/cdc_msc_freertos/src/main.c @@ -52,8 +52,7 @@ #define USBD_STACK_SIZE (3*configMINIMAL_STACK_SIZE/2) * (CFG_TUSB_DEBUG ? 2 : 1) #endif -#define CDC_STACK_SIZE configMINIMAL_STACK_SIZE -#define BLINKY_STACK_SIZE configMINIMAL_STACK_SIZE +#define CDC_STACK_SZIE configMINIMAL_STACK_SIZE //--------------------------------------------------------------------+ // MACRO CONSTANT TYPEDEF PROTOTYPES @@ -70,22 +69,21 @@ enum { BLINK_SUSPENDED = 2500, }; -// static task +// static timer & task #if configSUPPORT_STATIC_ALLOCATION -StackType_t blinky_stack[BLINKY_STACK_SIZE]; -StaticTask_t blinky_taskdef; +StaticTimer_t blinky_tmdef; StackType_t usb_device_stack[USBD_STACK_SIZE]; StaticTask_t usb_device_taskdef; -StackType_t cdc_stack[CDC_STACK_SIZE]; +StackType_t cdc_stack[CDC_STACK_SZIE]; StaticTask_t cdc_taskdef; #endif -static uint32_t blink_interval_ms = BLINK_NOT_MOUNTED; +TimerHandle_t blinky_tm; +static void led_blinky_cb(TimerHandle_t xTimer); static void usb_device_task(void *param); -void led_blinking_task(void* param); void cdc_task(void *params); //--------------------------------------------------------------------+ @@ -96,20 +94,22 @@ int main(void) { board_init(); #if configSUPPORT_STATIC_ALLOCATION - // blinky task - xTaskCreateStatic(led_blinking_task, "blinky", BLINKY_STACK_SIZE, NULL, 1, blinky_stack, &blinky_taskdef); + // soft timer for blinky + blinky_tm = xTimerCreateStatic(NULL, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), true, NULL, led_blinky_cb, &blinky_tmdef); // Create a task for tinyusb device stack xTaskCreateStatic(usb_device_task, "usbd", USBD_STACK_SIZE, NULL, configMAX_PRIORITIES-1, usb_device_stack, &usb_device_taskdef); // Create CDC task - xTaskCreateStatic(cdc_task, "cdc", CDC_STACK_SIZE, NULL, configMAX_PRIORITIES - 2, cdc_stack, &cdc_taskdef); + xTaskCreateStatic(cdc_task, "cdc", CDC_STACK_SZIE, NULL, configMAX_PRIORITIES-2, cdc_stack, &cdc_taskdef); #else - xTaskCreate(led_blinking_task, "blinky", BLINKY_STACK_SIZE, NULL, 1, NULL); + blinky_tm = xTimerCreate(NULL, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), true, NULL, led_blinky_cb); xTaskCreate(usb_device_task, "usbd", USBD_STACK_SIZE, NULL, configMAX_PRIORITIES - 1, NULL); xTaskCreate(cdc_task, "cdc", CDC_STACK_SZIE, NULL, configMAX_PRIORITIES - 2, NULL); #endif + xTimerStart(blinky_tm, 0); + // skip starting scheduler (and return) for ESP32-S2 or ESP32-S3 #if !TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) vTaskStartScheduler(); @@ -154,12 +154,12 @@ static void usb_device_task(void *param) { // Invoked when device is mounted void tud_mount_cb(void) { - blink_interval_ms = BLINK_MOUNTED; + xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_MOUNTED), 0); } // Invoked when device is unmounted void tud_umount_cb(void) { - blink_interval_ms = BLINK_NOT_MOUNTED; + xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), 0); } // Invoked when usb bus is suspended @@ -167,12 +167,16 @@ void tud_umount_cb(void) { // Within 7ms, device must draw an average of current less than 2.5 mA from bus void tud_suspend_cb(bool remote_wakeup_en) { (void) remote_wakeup_en; - blink_interval_ms = BLINK_SUSPENDED; + xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_SUSPENDED), 0); } // Invoked when usb bus is resumed void tud_resume_cb(void) { - blink_interval_ms = tud_mounted() ? BLINK_MOUNTED : BLINK_NOT_MOUNTED; + if (tud_mounted()) { + xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_MOUNTED), 0); + } else { + xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), 0); + } } //--------------------------------------------------------------------+ @@ -231,17 +235,10 @@ void tud_cdc_rx_cb(uint8_t itf) { //--------------------------------------------------------------------+ // BLINKING TASK //--------------------------------------------------------------------+ -void led_blinking_task(void* param) { - (void) param; - static uint32_t start_ms = 0; +static void led_blinky_cb(TimerHandle_t xTimer) { + (void) xTimer; static bool led_state = false; - while (1) { - // Blink every interval ms - vTaskDelay(blink_interval_ms / portTICK_PERIOD_MS); - start_ms += blink_interval_ms; - - board_led_write(led_state); - led_state = 1 - led_state; // toggle - } + board_led_write(led_state); + led_state = 1 - led_state; // toggle } diff --git a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk index c4dc65b63..f69700139 100644 --- a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk +++ b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk @@ -8,6 +8,9 @@ CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls -Wno-error=cast # All source paths should be relative to the top level. LD_FILE = $(MCU_DIR)/gcc/K32L2A41xxxxA_flash.ld +SRC_C += \ + $(MCU_DIR)/project_template/clock_config.c \ + # For flash-jlink target JLINK_DEVICE = K32L2A41xxxxA diff --git a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/clock_config.c b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/clock_config.c deleted file mode 100644 index 2814efc86..000000000 --- a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/clock_config.c +++ /dev/null @@ -1,491 +0,0 @@ -/* - * Copyright 2019 ,2021 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ -/* - * How to setup clock using clock driver functions: - * - * 1. Call CLOCK_InitXXX() to configure corresponding SCG clock source. - * Note: The clock could not be set when it is being used as system clock. - * In default out of reset, the CPU is clocked from FIRC(IRC48M), - * so before setting FIRC, change to use another available clock source. - * - * 2. Call CLOCK_SetXtal0Freq() to set XTAL0 frequency based on board settings. - * - * 3. Call CLOCK_SetXxxModeSysClkConfig() to set SCG mode for Xxx run mode. - * Wait until the system clock source is changed to target source. - * - * 4. If power mode change is needed, call SMC_SetPowerModeProtection() to allow - * corresponding power mode and SMC_SetPowerModeXxx() to change to Xxx mode. - * Supported run mode and clock restrictions could be found in Reference Manual. - */ - -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Clocks v7.0 -processor: K32L2A41xxxxA -package_id: K32L2A41VLL1A -mcu_data: ksdk2_0 -processor_version: 9.0.0 - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -#include "fsl_smc.h" -#include "clock_config.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ -#define SCG_CLKOUTCNFG_SIRC 2U /*!< SCG CLKOUT clock select: Slow IRC */ -#define SCG_SOSC_DISABLE 0U /*!< System OSC disabled */ -#define SCG_SPLL_DISABLE 0U /*!< System PLL disabled */ -#define SCG_SYS_OSC_CAP_0P 0U /*!< Oscillator 0pF capacitor load */ - -/******************************************************************************* - * Variables - ******************************************************************************/ -/* System clock frequency. */ -extern uint32_t SystemCoreClock; - -/******************************************************************************* - * Code - ******************************************************************************/ -/*FUNCTION********************************************************************** - * - * Function Name : CLOCK_CONFIG_SetScgOutSel - * Description : Set the SCG clock out select (CLKOUTSEL). - * Param setting : The selected clock source. - * - *END**************************************************************************/ -static void CLOCK_CONFIG_SetScgOutSel(uint8_t setting) -{ - SCG->CLKOUTCNFG = SCG_CLKOUTCNFG_CLKOUTSEL(setting); -} - -/*FUNCTION********************************************************************** - * - * Function Name : CLOCK_CONFIG_FircSafeConfig - * Description : This function is used to safely configure FIRC clock. - * In default out of reset, the CPU is clocked from FIRC(IRC48M). - * Before setting FIRC, change to use SIRC as system clock, - * then configure FIRC. After FIRC is set, change back to use FIRC - * in case SIRC need to be configured. - * Param fircConfig : FIRC configuration. - * - *END**************************************************************************/ -static void CLOCK_CONFIG_FircSafeConfig(const scg_firc_config_t *fircConfig) -{ - scg_sys_clk_config_t curConfig; - const scg_sirc_config_t scgSircConfig = {.enableMode = kSCG_SircEnable, - .div1 = kSCG_AsyncClkDisable, - .div3 = kSCG_AsyncClkDivBy2, - .range = kSCG_SircRangeHigh}; - scg_sys_clk_config_t sysClkSafeConfigSource = { - .divSlow = kSCG_SysClkDivBy4, /* Slow clock divider */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved1 = 0, - .reserved2 = 0, - .reserved3 = 0, -#endif - .divCore = kSCG_SysClkDivBy1, /* Core clock divider */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved4 = 0, -#endif - .src = kSCG_SysClkSrcSirc, /* System clock source */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved5 = 0, -#endif - }; - /* Init Sirc. */ - CLOCK_InitSirc(&scgSircConfig); - /* Change to use SIRC as system clock source to prepare to change FIRCCFG register. */ - CLOCK_SetRunModeSysClkConfig(&sysClkSafeConfigSource); - /* Wait for clock source switch finished. */ - do - { - CLOCK_GetCurSysClkConfig(&curConfig); - } while (curConfig.src != sysClkSafeConfigSource.src); - - /* Init Firc. */ - CLOCK_InitFirc(fircConfig); - /* Change back to use FIRC as system clock source in order to configure SIRC if needed. */ - sysClkSafeConfigSource.src = kSCG_SysClkSrcFirc; - CLOCK_SetRunModeSysClkConfig(&sysClkSafeConfigSource); - /* Wait for clock source switch finished. */ - do - { - CLOCK_GetCurSysClkConfig(&curConfig); - } while (curConfig.src != sysClkSafeConfigSource.src); -} - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ -void BOARD_InitBootClocks(void) -{ - BOARD_BootClockRUN(); -} - -/******************************************************************************* - ********************** Configuration BOARD_BootClockRUN *********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockRUN -called_from_default_init: true -outputs: -- {id: Core_clock.outFreq, value: 48 MHz} -- {id: FIRCDIV1_CLK.outFreq, value: 48 MHz} -- {id: FIRCDIV3_CLK.outFreq, value: 48 MHz} -- {id: LPO_clock.outFreq, value: 1 kHz} -- {id: OSC32KCLK.outFreq, value: 32.768 kHz} -- {id: SIRCDIV3_CLK.outFreq, value: 4 MHz} -- {id: SIRC_CLK.outFreq, value: 8 MHz} -- {id: SOSCDIV3_CLK.outFreq, value: 32.768 kHz} -- {id: SOSCER_CLK.outFreq, value: 32.768 kHz} -- {id: SOSC_CLK.outFreq, value: 32.768 kHz} -- {id: Slow_clock.outFreq, value: 24 MHz} -- {id: System_clock.outFreq, value: 48 MHz} -settings: -- {id: SCG.FIRCDIV1.scale, value: '1', locked: true} -- {id: SCG.FIRCDIV3.scale, value: '1', locked: true} -- {id: SCG.SIRCDIV3.scale, value: '2', locked: true} -- {id: SCG.SOSCDIV3.scale, value: '1', locked: true} -- {id: SCG_SOSCCFG_OSC_MODE_CFG, value: ModeOscLowPower} -- {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled} -- {id: SCG_SOSCCSR_SOSCERCLKEN_CFG, value: Enabled} -sources: -- {id: SCG.SOSC.outFreq, value: 32.768 kHz, enabled: true} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockRUN configuration - ******************************************************************************/ -const scg_sys_clk_config_t g_sysClkConfig_BOARD_BootClockRUN = - { - .divSlow = kSCG_SysClkDivBy2, /* Slow Clock Divider: divided by 2 */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved1 = 0, - .reserved2 = 0, - .reserved3 = 0, -#endif - .divCore = kSCG_SysClkDivBy1, /* Core Clock Divider: divided by 1 */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved4 = 0, -#endif - .src = kSCG_SysClkSrcFirc, /* Fast IRC is selected as System Clock Source */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved5 = 0, -#endif - }; -const scg_sosc_config_t g_scgSysOscConfig_BOARD_BootClockRUN = - { - .freq = 32768U, /* System Oscillator frequency: 32768Hz */ - .enableMode = kSCG_SysOscEnable | kSCG_SysOscEnableErClk,/* Enable System OSC clock, Enable OSCERCLK */ - .monitorMode = kSCG_SysOscMonitorDisable, /* Monitor disabled */ - .div1 = kSCG_AsyncClkDisable, /* System OSC Clock Divider 1: Clock output is disabled */ - .div3 = kSCG_AsyncClkDivBy1, /* System OSC Clock Divider 3: divided by 1 */ - .capLoad = SCG_SYS_OSC_CAP_0P, /* Oscillator capacity load: 0pF */ - .workMode = kSCG_SysOscModeOscLowPower, /* Oscillator low power */ - }; -const scg_sirc_config_t g_scgSircConfig_BOARD_BootClockRUN = - { - .enableMode = kSCG_SircEnable | kSCG_SircEnableInLowPower,/* Enable SIRC clock, Enable SIRC in low power mode */ - .div1 = kSCG_AsyncClkDisable, /* Slow IRC Clock Divider 1: Clock output is disabled */ - .div3 = kSCG_AsyncClkDivBy2, /* Slow IRC Clock Divider 3: divided by 2 */ - .range = kSCG_SircRangeHigh, /* Slow IRC high range clock (8 MHz) */ - }; -const scg_firc_config_t g_scgFircConfig_BOARD_BootClockRUN = - { - .enableMode = kSCG_FircEnable, /* Enable FIRC clock */ - .div1 = kSCG_AsyncClkDivBy1, /* Fast IRC Clock Divider 1: divided by 1 */ - .div3 = kSCG_AsyncClkDivBy1, /* Fast IRC Clock Divider 3: divided by 1 */ - .range = kSCG_FircRange48M, /* Fast IRC is trimmed to 48MHz */ - .trimConfig = NULL, /* Fast IRC Trim disabled */ - }; -const scg_spll_config_t g_scgSysPllConfig_BOARD_BootClockRUN = - { - .enableMode = SCG_SPLL_DISABLE, /* System PLL disabled */ - .monitorMode = kSCG_SysPllMonitorDisable, /* Monitor disabled */ - .div1 = kSCG_AsyncClkDisable, /* System PLL Clock Divider 1: Clock output is disabled */ - .div3 = kSCG_AsyncClkDisable, /* System PLL Clock Divider 3: Clock output is disabled */ - .src = kSCG_SysPllSrcSysOsc, /* System PLL clock source is System OSC */ - .prediv = 0, /* Divided by 1 */ - .mult = 0, /* Multiply Factor is 16 */ - }; -/******************************************************************************* - * Code for BOARD_BootClockRUN configuration - ******************************************************************************/ -void BOARD_BootClockRUN(void) -{ - scg_sys_clk_config_t curConfig; - - /* Init SOSC according to board configuration. */ - CLOCK_InitSysOsc(&g_scgSysOscConfig_BOARD_BootClockRUN); - /* Set the XTAL0 frequency based on board settings. */ - CLOCK_SetXtal0Freq(g_scgSysOscConfig_BOARD_BootClockRUN.freq); - /* Init FIRC. */ - CLOCK_CONFIG_FircSafeConfig(&g_scgFircConfig_BOARD_BootClockRUN); - /* Init SIRC. */ - CLOCK_InitSirc(&g_scgSircConfig_BOARD_BootClockRUN); - /* Set SCG to FIRC mode. */ - CLOCK_SetRunModeSysClkConfig(&g_sysClkConfig_BOARD_BootClockRUN); - /* Wait for clock source switch finished. */ - do - { - CLOCK_GetCurSysClkConfig(&curConfig); - } while (curConfig.src != g_sysClkConfig_BOARD_BootClockRUN.src); - /* Set SystemCoreClock variable. */ - SystemCoreClock = BOARD_BOOTCLOCKRUN_CORE_CLOCK; -} - -/******************************************************************************* - ********************* Configuration BOARD_BootClockHSRUN ********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockHSRUN -outputs: -- {id: CLKOUT.outFreq, value: 8 MHz} -- {id: Core_clock.outFreq, value: 96 MHz, locked: true, accuracy: '0.001'} -- {id: FIRCDIV1_CLK.outFreq, value: 48 MHz} -- {id: FIRCDIV3_CLK.outFreq, value: 48 MHz} -- {id: LPO_clock.outFreq, value: 1 kHz} -- {id: OSC32KCLK.outFreq, value: 32.768 kHz} -- {id: PLLDIV1_CLK.outFreq, value: 96 MHz} -- {id: PLLDIV3_CLK.outFreq, value: 96 MHz} -- {id: SIRCDIV1_CLK.outFreq, value: 8 MHz} -- {id: SIRCDIV3_CLK.outFreq, value: 8 MHz} -- {id: SIRC_CLK.outFreq, value: 8 MHz} -- {id: SOSCDIV1_CLK.outFreq, value: 32.768 kHz} -- {id: SOSCDIV3_CLK.outFreq, value: 32.768 kHz} -- {id: SOSCER_CLK.outFreq, value: 32.768 kHz} -- {id: SOSC_CLK.outFreq, value: 32.768 kHz} -- {id: Slow_clock.outFreq, value: 24 MHz, locked: true, accuracy: '0.001'} -- {id: System_clock.outFreq, value: 96 MHz} -settings: -- {id: SCGMode, value: SPLL} -- {id: powerMode, value: HSRUN} -- {id: CLKOUTConfig, value: 'yes'} -- {id: SCG.DIVSLOW.scale, value: '4'} -- {id: SCG.FIRCDIV1.scale, value: '1', locked: true} -- {id: SCG.FIRCDIV3.scale, value: '1', locked: true} -- {id: SCG.PREDIV.scale, value: '4'} -- {id: SCG.SCSSEL.sel, value: SCG.SPLL_DIV2_CLK} -- {id: SCG.SIRCDIV1.scale, value: '1', locked: true} -- {id: SCG.SIRCDIV3.scale, value: '1', locked: true} -- {id: SCG.SOSCDIV1.scale, value: '1', locked: true} -- {id: SCG.SOSCDIV3.scale, value: '1', locked: true} -- {id: SCG.SPLLDIV1.scale, value: '1', locked: true} -- {id: SCG.SPLLDIV3.scale, value: '1', locked: true} -- {id: SCG.SPLLSRCSEL.sel, value: SCG.FIRC} -- {id: SCG_SOSCCFG_OSC_MODE_CFG, value: ModeOscLowPower} -- {id: SCG_SOSCCSR_SOSCEN_CFG, value: Enabled} -- {id: SCG_SOSCCSR_SOSCERCLKEN_CFG, value: Enabled} -- {id: SCG_SPLLCSR_SPLLEN_CFG, value: Enabled} -sources: -- {id: SCG.SOSC.outFreq, value: 32.768 kHz, enabled: true} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockHSRUN configuration - ******************************************************************************/ -const scg_sys_clk_config_t g_sysClkConfig_BOARD_BootClockHSRUN = - { - .divSlow = kSCG_SysClkDivBy4, /* Slow Clock Divider: divided by 4 */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved1 = 0, - .reserved2 = 0, - .reserved3 = 0, -#endif - .divCore = kSCG_SysClkDivBy1, /* Core Clock Divider: divided by 1 */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved4 = 0, -#endif - .src = kSCG_SysClkSrcSysPll, /* System PLL is selected as System Clock Source */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved5 = 0, -#endif - }; -const scg_sosc_config_t g_scgSysOscConfig_BOARD_BootClockHSRUN = - { - .freq = 32768U, /* System Oscillator frequency: 32768Hz */ - .enableMode = kSCG_SysOscEnable | kSCG_SysOscEnableErClk,/* Enable System OSC clock, Enable OSCERCLK */ - .monitorMode = kSCG_SysOscMonitorDisable, /* Monitor disabled */ - .div1 = kSCG_AsyncClkDivBy1, /* System OSC Clock Divider 1: divided by 1 */ - .div3 = kSCG_AsyncClkDivBy1, /* System OSC Clock Divider 3: divided by 1 */ - .capLoad = SCG_SYS_OSC_CAP_0P, /* Oscillator capacity load: 0pF */ - .workMode = kSCG_SysOscModeOscLowPower, /* Oscillator low power */ - }; -const scg_sirc_config_t g_scgSircConfig_BOARD_BootClockHSRUN = - { - .enableMode = kSCG_SircEnable | kSCG_SircEnableInLowPower,/* Enable SIRC clock, Enable SIRC in low power mode */ - .div1 = kSCG_AsyncClkDivBy1, /* Slow IRC Clock Divider 1: divided by 1 */ - .div3 = kSCG_AsyncClkDivBy1, /* Slow IRC Clock Divider 3: divided by 1 */ - .range = kSCG_SircRangeHigh, /* Slow IRC high range clock (8 MHz) */ - }; -const scg_firc_config_t g_scgFircConfig_BOARD_BootClockHSRUN = - { - .enableMode = kSCG_FircEnable, /* Enable FIRC clock */ - .div1 = kSCG_AsyncClkDivBy1, /* Fast IRC Clock Divider 1: divided by 1 */ - .div3 = kSCG_AsyncClkDivBy1, /* Fast IRC Clock Divider 3: divided by 1 */ - .range = kSCG_FircRange48M, /* Fast IRC is trimmed to 48MHz */ - .trimConfig = NULL, /* Fast IRC Trim disabled */ - }; -const scg_spll_config_t g_scgSysPllConfig_BOARD_BootClockHSRUN = - { - .enableMode = kSCG_SysPllEnable, /* Enable SPLL clock */ - .monitorMode = kSCG_SysPllMonitorDisable, /* Monitor disabled */ - .div1 = kSCG_AsyncClkDivBy1, /* System PLL Clock Divider 1: divided by 1 */ - .div3 = kSCG_AsyncClkDivBy1, /* System PLL Clock Divider 3: divided by 1 */ - .src = kSCG_SysPllSrcFirc, /* System PLL clock source is Fast IRC */ - .prediv = 3, /* Divided by 4 */ - .mult = 0, /* Multiply Factor is 16 */ - }; -/******************************************************************************* - * Code for BOARD_BootClockHSRUN configuration - ******************************************************************************/ -void BOARD_BootClockHSRUN(void) -{ - scg_sys_clk_config_t curConfig; - - /* Init SOSC according to board configuration. */ - CLOCK_InitSysOsc(&g_scgSysOscConfig_BOARD_BootClockHSRUN); - /* Set the XTAL0 frequency based on board settings. */ - CLOCK_SetXtal0Freq(g_scgSysOscConfig_BOARD_BootClockHSRUN.freq); - /* Init FIRC. */ - CLOCK_CONFIG_FircSafeConfig(&g_scgFircConfig_BOARD_BootClockHSRUN); - /* Init SIRC. */ - CLOCK_InitSirc(&g_scgSircConfig_BOARD_BootClockHSRUN); - /* Init SysPll. */ - CLOCK_InitSysPll(&g_scgSysPllConfig_BOARD_BootClockHSRUN); - /* Set HSRUN power mode. */ - SMC_SetPowerModeProtection(SMC, kSMC_AllowPowerModeAll); - SMC_SetPowerModeHsrun(SMC); - while (SMC_GetPowerModeState(SMC) != kSMC_PowerStateHsrun) - { - } - - /* Set SCG to SPLL mode. */ - CLOCK_SetHsrunModeSysClkConfig(&g_sysClkConfig_BOARD_BootClockHSRUN); - /* Wait for clock source switch finished. */ - do - { - CLOCK_GetCurSysClkConfig(&curConfig); - } while (curConfig.src != g_sysClkConfig_BOARD_BootClockHSRUN.src); - /* Set SystemCoreClock variable. */ - SystemCoreClock = BOARD_BOOTCLOCKHSRUN_CORE_CLOCK; - /* Set SCG CLKOUT selection. */ - CLOCK_CONFIG_SetScgOutSel(SCG_CLKOUTCNFG_SIRC); -} - -/******************************************************************************* - ********************* Configuration BOARD_BootClockVLPR *********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockVLPR -outputs: -- {id: Core_clock.outFreq, value: 8 MHz, locked: true, accuracy: '0.001'} -- {id: LPO_clock.outFreq, value: 1 kHz} -- {id: SIRC_CLK.outFreq, value: 8 MHz} -- {id: Slow_clock.outFreq, value: 1 MHz, locked: true, accuracy: '0.001'} -- {id: System_clock.outFreq, value: 8 MHz} -settings: -- {id: SCGMode, value: SIRC} -- {id: powerMode, value: VLPR} -- {id: SCG.DIVSLOW.scale, value: '8'} -- {id: SCG.SCSSEL.sel, value: SCG.SIRC} -- {id: SCG_FIRCCSR_FIRCLPEN_CFG, value: Enabled} -sources: -- {id: SCG.SOSC.outFreq, value: 32.768 kHz, enabled: true} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockVLPR configuration - ******************************************************************************/ -const scg_sys_clk_config_t g_sysClkConfig_BOARD_BootClockVLPR = - { - .divSlow = kSCG_SysClkDivBy8, /* Slow Clock Divider: divided by 8 */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved1 = 0, - .reserved2 = 0, - .reserved3 = 0, -#endif - .divCore = kSCG_SysClkDivBy1, /* Core Clock Divider: divided by 1 */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved4 = 0, -#endif - .src = kSCG_SysClkSrcSirc, /* Slow IRC is selected as System Clock Source */ -#if FSL_CLOCK_DRIVER_VERSION < MAKE_VERSION(2, 1, 1) - .reserved5 = 0, -#endif - }; -const scg_sosc_config_t g_scgSysOscConfig_BOARD_BootClockVLPR = - { - .freq = 0U, /* System Oscillator frequency: 0Hz */ - .enableMode = SCG_SOSC_DISABLE, /* System OSC disabled */ - .monitorMode = kSCG_SysOscMonitorDisable, /* Monitor disabled */ - .div1 = kSCG_AsyncClkDisable, /* System OSC Clock Divider 1: Clock output is disabled */ - .div3 = kSCG_AsyncClkDisable, /* System OSC Clock Divider 3: Clock output is disabled */ - .capLoad = SCG_SYS_OSC_CAP_0P, /* Oscillator capacity load: 0pF */ - .workMode = kSCG_SysOscModeExt, /* Use external clock */ - }; -const scg_sirc_config_t g_scgSircConfig_BOARD_BootClockVLPR = - { - .enableMode = kSCG_SircEnable | kSCG_SircEnableInLowPower,/* Enable SIRC clock, Enable SIRC in low power mode */ - .div1 = kSCG_AsyncClkDisable, /* Slow IRC Clock Divider 1: Clock output is disabled */ - .div3 = kSCG_AsyncClkDisable, /* Slow IRC Clock Divider 3: Clock output is disabled */ - .range = kSCG_SircRangeHigh, /* Slow IRC high range clock (8 MHz) */ - }; -const scg_firc_config_t g_scgFircConfig_BOARD_BootClockVLPR = - { - .enableMode = kSCG_FircEnable | kSCG_FircEnableInLowPower,/* Enable FIRC clock, Enable FIRC in low power mode */ - .div1 = kSCG_AsyncClkDisable, /* Fast IRC Clock Divider 1: Clock output is disabled */ - .div3 = kSCG_AsyncClkDisable, /* Fast IRC Clock Divider 3: Clock output is disabled */ - .range = kSCG_FircRange48M, /* Fast IRC is trimmed to 48MHz */ - .trimConfig = NULL, /* Fast IRC Trim disabled */ - }; -const scg_spll_config_t g_scgSysPllConfig_BOARD_BootClockVLPR = - { - .enableMode = SCG_SPLL_DISABLE, /* System PLL disabled */ - .monitorMode = kSCG_SysPllMonitorDisable, /* Monitor disabled */ - .div1 = kSCG_AsyncClkDisable, /* System PLL Clock Divider 1: Clock output is disabled */ - .div3 = kSCG_AsyncClkDisable, /* System PLL Clock Divider 3: Clock output is disabled */ - .src = kSCG_SysPllSrcSysOsc, /* System PLL clock source is System OSC */ - .prediv = 0, /* Divided by 1 */ - .mult = 0, /* Multiply Factor is 16 */ - }; -/******************************************************************************* - * Code for BOARD_BootClockVLPR configuration - ******************************************************************************/ -void BOARD_BootClockVLPR(void) -{ - /* Init FIRC. */ - CLOCK_CONFIG_FircSafeConfig(&g_scgFircConfig_BOARD_BootClockVLPR); - /* Init SIRC. */ - CLOCK_InitSirc(&g_scgSircConfig_BOARD_BootClockVLPR); - /* Allow SMC all power modes. */ - SMC_SetPowerModeProtection(SMC, kSMC_AllowPowerModeAll); - /* Set VLPR power mode. */ - SMC_SetPowerModeVlpr(SMC); - while (SMC_GetPowerModeState(SMC) != kSMC_PowerStateVlpr) - { - } - /* Set SystemCoreClock variable. */ - SystemCoreClock = BOARD_BOOTCLOCKVLPR_CORE_CLOCK; -} diff --git a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/clock_config.h b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/clock_config.h deleted file mode 100644 index c01d5e03c..000000000 --- a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/clock_config.h +++ /dev/null @@ -1,164 +0,0 @@ -/* - * Copyright 2019 ,2021 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _CLOCK_CONFIG_H_ -#define _CLOCK_CONFIG_H_ - -#include "fsl_common.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ -#define BOARD_XTAL0_CLK_HZ 32768U /*!< Board xtal0 frequency in Hz */ - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes default configuration of clocks. - * - */ -void BOARD_InitBootClocks(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ********************** Configuration BOARD_BootClockRUN *********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockRUN configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKRUN_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ - -/*! @brief SCG set for BOARD_BootClockRUN configuration. - */ -extern const scg_sys_clk_config_t g_sysClkConfig_BOARD_BootClockRUN; -/*! @brief System OSC set for BOARD_BootClockRUN configuration. - */ -extern const scg_sosc_config_t g_scgSysOscConfig_BOARD_BootClockRUN; -/*! @brief SIRC set for BOARD_BootClockRUN configuration. - */ -extern const scg_sirc_config_t g_scgSircConfig_BOARD_BootClockRUN; -/*! @brief FIRC set for BOARD_BootClockRUN configuration. - */ -extern const scg_firc_config_t g_scgFircConfigBOARD_BootClockRUN; -extern const scg_spll_config_t g_scgSysPllConfigBOARD_BootClockRUN; -/*! @brief Low Power FLL set for BOARD_BootClockRUN configuration. - */ - -/******************************************************************************* - * API for BOARD_BootClockRUN configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockRUN(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ********************* Configuration BOARD_BootClockHSRUN ********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockHSRUN configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKHSRUN_CORE_CLOCK 96000000U /*!< Core clock frequency: 96000000Hz */ - -/*! @brief SCG set for BOARD_BootClockHSRUN configuration. - */ -extern const scg_sys_clk_config_t g_sysClkConfig_BOARD_BootClockHSRUN; -/*! @brief System OSC set for BOARD_BootClockHSRUN configuration. - */ -extern const scg_sosc_config_t g_scgSysOscConfig_BOARD_BootClockHSRUN; -/*! @brief SIRC set for BOARD_BootClockHSRUN configuration. - */ -extern const scg_sirc_config_t g_scgSircConfig_BOARD_BootClockHSRUN; -/*! @brief FIRC set for BOARD_BootClockHSRUN configuration. - */ -extern const scg_firc_config_t g_scgFircConfigBOARD_BootClockHSRUN; -extern const scg_spll_config_t g_scgSysPllConfigBOARD_BootClockHSRUN; -/*! @brief Low Power FLL set for BOARD_BootClockHSRUN configuration. - */ - -/******************************************************************************* - * API for BOARD_BootClockHSRUN configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockHSRUN(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ********************* Configuration BOARD_BootClockVLPR *********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockVLPR configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKVLPR_CORE_CLOCK 8000000U /*!< Core clock frequency: 8000000Hz */ - -/*! @brief SCG set for BOARD_BootClockVLPR configuration. - */ -extern const scg_sys_clk_config_t g_sysClkConfig_BOARD_BootClockVLPR; -/*! @brief System OSC set for BOARD_BootClockVLPR configuration. - */ -extern const scg_sosc_config_t g_scgSysOscConfig_BOARD_BootClockVLPR; -/*! @brief SIRC set for BOARD_BootClockVLPR configuration. - */ -extern const scg_sirc_config_t g_scgSircConfig_BOARD_BootClockVLPR; -/*! @brief FIRC set for BOARD_BootClockVLPR configuration. - */ -extern const scg_firc_config_t g_scgFircConfigBOARD_BootClockVLPR; -extern const scg_spll_config_t g_scgSysPllConfigBOARD_BootClockVLPR; -/*! @brief Low Power FLL set for BOARD_BootClockVLPR configuration. - */ - -/******************************************************************************* - * API for BOARD_BootClockVLPR configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockVLPR(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk index 9cf36c500..82456b721 100644 --- a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk +++ b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk @@ -8,6 +8,9 @@ CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls # All source paths should be relative to the top level. LD_FILE = $(MCU_DIR)/gcc/K32L2B31xxxxA_flash.ld +SRC_C += \ + $(MCU_DIR)/project_template/clock_config.c \ + # For flash-jlink target JLINK_DEVICE = K32L2B31xxxxA diff --git a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/clock_config.c b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/clock_config.c deleted file mode 100644 index e74000827..000000000 --- a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/clock_config.c +++ /dev/null @@ -1,220 +0,0 @@ -/* - * Copyright 2019 ,2021 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ -/* - * How to setup clock using clock driver functions: - * - * 1. CLOCK_SetSimSafeDivs, to make sure core clock, bus clock, flexbus clock - * and flash clock are in allowed range during clock mode switch. - * - * 2. Call CLOCK_Osc0Init to setup OSC clock, if it is used in target mode. - * - * 3. Call CLOCK_SetMcgliteConfig to set MCG_Lite configuration. - * - * 4. Call CLOCK_SetSimConfig to set the clock configuration in SIM. - */ - -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!GlobalInfo -product: Clocks v7.0 -processor: K32L2B31xxxxA -package_id: K32L2B31VLH0A -mcu_data: ksdk2_0 -processor_version: 9.0.0 -board: FRDM-K32L2B - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -#include "fsl_smc.h" -#include "clock_config.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ -#define OSC_CAP0P 0U /*!< Oscillator 0pF capacitor load */ -#define OSC_ER_CLK_DISABLE 0U /*!< Disable external reference clock */ -#define SIM_OSC32KSEL_OSC32KCLK_CLK 0U /*!< OSC32KSEL select: OSC32KCLK clock */ - -/******************************************************************************* - * Variables - ******************************************************************************/ -/* System clock frequency. */ -extern uint32_t SystemCoreClock; - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ -void BOARD_InitBootClocks(void) -{ - BOARD_BootClockRUN(); -} - -/******************************************************************************* - ********************** Configuration BOARD_BootClockRUN *********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockRUN -called_from_default_init: true -outputs: -- {id: Bus_clock.outFreq, value: 24 MHz} -- {id: Core_clock.outFreq, value: 48 MHz} -- {id: Flash_clock.outFreq, value: 24 MHz} -- {id: LPO_clock.outFreq, value: 1 kHz} -- {id: MCGIRCLK.outFreq, value: 8 MHz} -- {id: MCGPCLK.outFreq, value: 48 MHz} -- {id: System_clock.outFreq, value: 48 MHz} -settings: -- {id: MCGMode, value: HIRC} -- {id: MCG.CLKS.sel, value: MCG.HIRC} -- {id: MCG_C2_OSC_MODE_CFG, value: ModeOscLowPower} -- {id: MCG_C2_RANGE0_CFG, value: Very_high} -- {id: MCG_MC_HIRCEN_CFG, value: Enabled} -- {id: OSC0_CR_ERCLKEN_CFG, value: Enabled} -- {id: OSC_CR_ERCLKEN_CFG, value: Enabled} -- {id: SIM.CLKOUTSEL.sel, value: MCG.MCGPCLK} -- {id: SIM.COPCLKSEL.sel, value: OSC.OSCERCLK} -- {id: SIM.FLEXIOSRCSEL.sel, value: MCG.MCGPCLK} -- {id: SIM.LPUART0SRCSEL.sel, value: MCG.MCGPCLK} -- {id: SIM.LPUART1SRCSEL.sel, value: MCG.MCGPCLK} -- {id: SIM.RTCCLKOUTSEL.sel, value: OSC.OSCERCLK} -- {id: SIM.TPMSRCSEL.sel, value: MCG.MCGPCLK} -- {id: SIM.USBSRCSEL.sel, value: MCG.MCGPCLK} -sources: -- {id: MCG.HIRC.outFreq, value: 48 MHz} -- {id: OSC.OSC.outFreq, value: 32 MHz} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockRUN configuration - ******************************************************************************/ -const mcglite_config_t mcgliteConfig_BOARD_BootClockRUN = - { - .outSrc = kMCGLITE_ClkSrcHirc, /* MCGOUTCLK source is HIRC */ - .irclkEnableMode = kMCGLITE_IrclkEnable, /* MCGIRCLK enabled, MCGIRCLK disabled in STOP mode */ - .ircs = kMCGLITE_Lirc8M, /* Slow internal reference (LIRC) 8 MHz clock selected */ - .fcrdiv = kMCGLITE_LircDivBy1, /* Low-frequency Internal Reference Clock Divider: divided by 1 */ - .lircDiv2 = kMCGLITE_LircDivBy1, /* Second Low-frequency Internal Reference Clock Divider: divided by 1 */ - .hircEnableInNotHircMode = true, /* HIRC source is enabled */ - }; -const sim_clock_config_t simConfig_BOARD_BootClockRUN = - { - .er32kSrc = SIM_OSC32KSEL_OSC32KCLK_CLK, /* OSC32KSEL select: OSC32KCLK clock */ - .clkdiv1 = 0x10000U, /* SIM_CLKDIV1 - OUTDIV1: /1, OUTDIV4: /2 */ - }; -const osc_config_t oscConfig_BOARD_BootClockRUN = - { - .freq = 0U, /* Oscillator frequency: 0Hz */ - .capLoad = (OSC_CAP0P), /* Oscillator capacity load: 0pF */ - .workMode = kOSC_ModeOscLowPower, /* Oscillator low power */ - .oscerConfig = - { - .enableMode = kOSC_ErClkEnable, /* Enable external reference clock, disable external reference clock in STOP mode */ - } - }; - -/******************************************************************************* - * Code for BOARD_BootClockRUN configuration - ******************************************************************************/ -void BOARD_BootClockRUN(void) -{ - /* Set the system clock dividers in SIM to safe value. */ - CLOCK_SetSimSafeDivs(); - /* Set MCG to HIRC mode. */ - CLOCK_SetMcgliteConfig(&mcgliteConfig_BOARD_BootClockRUN); - /* Set the clock configuration in SIM module. */ - CLOCK_SetSimConfig(&simConfig_BOARD_BootClockRUN); - /* Set SystemCoreClock variable. */ - SystemCoreClock = BOARD_BOOTCLOCKRUN_CORE_CLOCK; -} - -/******************************************************************************* - ********************* Configuration BOARD_BootClockVLPR *********************** - ******************************************************************************/ -/* clang-format off */ -/* TEXT BELOW IS USED AS SETTING FOR TOOLS ************************************* -!!Configuration -name: BOARD_BootClockVLPR -outputs: -- {id: Bus_clock.outFreq, value: 1 MHz} -- {id: Core_clock.outFreq, value: 2 MHz} -- {id: Flash_clock.outFreq, value: 1 MHz} -- {id: LPO_clock.outFreq, value: 1 kHz} -- {id: MCGIRCLK.outFreq, value: 2 MHz} -- {id: System_clock.outFreq, value: 2 MHz} -settings: -- {id: MCGMode, value: LIRC2M} -- {id: powerMode, value: VLPR} -- {id: MCG_C2_OSC_MODE_CFG, value: ModeOscLowPower} -- {id: RTCCLKOUTConfig, value: 'yes'} -- {id: SIM.OUTDIV4.scale, value: '2', locked: true} -- {id: SIM.RTCCLKOUTSEL.sel, value: OSC.OSCERCLK} -sources: -- {id: MCG.LIRC.outFreq, value: 2 MHz} -- {id: OSC.OSC.outFreq, value: 32.768 kHz} - * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS **********/ -/* clang-format on */ - -/******************************************************************************* - * Variables for BOARD_BootClockVLPR configuration - ******************************************************************************/ -const mcglite_config_t mcgliteConfig_BOARD_BootClockVLPR = - { - .outSrc = kMCGLITE_ClkSrcLirc, /* MCGOUTCLK source is LIRC */ - .irclkEnableMode = kMCGLITE_IrclkEnable, /* MCGIRCLK enabled, MCGIRCLK disabled in STOP mode */ - .ircs = kMCGLITE_Lirc2M, /* Slow internal reference (LIRC) 2 MHz clock selected */ - .fcrdiv = kMCGLITE_LircDivBy1, /* Low-frequency Internal Reference Clock Divider: divided by 1 */ - .lircDiv2 = kMCGLITE_LircDivBy1, /* Second Low-frequency Internal Reference Clock Divider: divided by 1 */ - .hircEnableInNotHircMode = false, /* HIRC source is not enabled */ - }; -const sim_clock_config_t simConfig_BOARD_BootClockVLPR = - { - .er32kSrc = SIM_OSC32KSEL_OSC32KCLK_CLK, /* OSC32KSEL select: OSC32KCLK clock */ - .clkdiv1 = 0x10000U, /* SIM_CLKDIV1 - OUTDIV1: /1, OUTDIV4: /2 */ - }; -const osc_config_t oscConfig_BOARD_BootClockVLPR = - { - .freq = 0U, /* Oscillator frequency: 0Hz */ - .capLoad = (OSC_CAP0P), /* Oscillator capacity load: 0pF */ - .workMode = kOSC_ModeOscLowPower, /* Oscillator low power */ - .oscerConfig = - { - .enableMode = OSC_ER_CLK_DISABLE, /* Disable external reference clock */ - } - }; - -/******************************************************************************* - * Code for BOARD_BootClockVLPR configuration - ******************************************************************************/ -void BOARD_BootClockVLPR(void) -{ - /* Set the system clock dividers in SIM to safe value. */ - CLOCK_SetSimSafeDivs(); - /* Set MCG to LIRC2M mode. */ - CLOCK_SetMcgliteConfig(&mcgliteConfig_BOARD_BootClockVLPR); - /* Set the clock configuration in SIM module. */ - CLOCK_SetSimConfig(&simConfig_BOARD_BootClockVLPR); - /* Set VLPR power mode. */ - SMC_SetPowerModeProtection(SMC, kSMC_AllowPowerModeAll); -#if (defined(FSL_FEATURE_SMC_HAS_LPWUI) && FSL_FEATURE_SMC_HAS_LPWUI) - SMC_SetPowerModeVlpr(SMC, false); -#else - SMC_SetPowerModeVlpr(SMC); -#endif - while (SMC_GetPowerModeState(SMC) != kSMC_PowerStateVlpr) - { - } - /* Set SystemCoreClock variable. */ - SystemCoreClock = BOARD_BOOTCLOCKVLPR_CORE_CLOCK; -} diff --git a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/clock_config.h b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/clock_config.h deleted file mode 100644 index 37328e7d8..000000000 --- a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/clock_config.h +++ /dev/null @@ -1,110 +0,0 @@ -/* - * Copyright 2019 ,2021 NXP - * All rights reserved. - * - * SPDX-License-Identifier: BSD-3-Clause - */ - -/*********************************************************************************************************************** - * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file - * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. - **********************************************************************************************************************/ - -#ifndef _CLOCK_CONFIG_H_ -#define _CLOCK_CONFIG_H_ - -#include "fsl_common.h" - -/******************************************************************************* - * Definitions - ******************************************************************************/ - -/******************************************************************************* - ************************ BOARD_InitBootClocks function ************************ - ******************************************************************************/ - -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes default configuration of clocks. - * - */ -void BOARD_InitBootClocks(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ********************** Configuration BOARD_BootClockRUN *********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockRUN configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKRUN_CORE_CLOCK 48000000U /*!< Core clock frequency: 48000000Hz */ - -/*! @brief MCG lite set for BOARD_BootClockRUN configuration. - */ -extern const mcglite_config_t mcgliteConfig_BOARD_BootClockRUN; -/*! @brief SIM module set for BOARD_BootClockRUN configuration. - */ -extern const sim_clock_config_t simConfig_BOARD_BootClockRUN; -/*! @brief OSC set for BOARD_BootClockRUN configuration. - */ -extern const osc_config_t oscConfig_BOARD_BootClockRUN; - -/******************************************************************************* - * API for BOARD_BootClockRUN configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockRUN(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -/******************************************************************************* - ********************* Configuration BOARD_BootClockVLPR *********************** - ******************************************************************************/ -/******************************************************************************* - * Definitions for BOARD_BootClockVLPR configuration - ******************************************************************************/ -#define BOARD_BOOTCLOCKVLPR_CORE_CLOCK 2000000U /*!< Core clock frequency: 2000000Hz */ - -/*! @brief MCG lite set for BOARD_BootClockVLPR configuration. - */ -extern const mcglite_config_t mcgliteConfig_BOARD_BootClockVLPR; -/*! @brief SIM module set for BOARD_BootClockVLPR configuration. - */ -extern const sim_clock_config_t simConfig_BOARD_BootClockVLPR; -/*! @brief OSC set for BOARD_BootClockVLPR configuration. - */ -extern const osc_config_t oscConfig_BOARD_BootClockVLPR; - -/******************************************************************************* - * API for BOARD_BootClockVLPR configuration - ******************************************************************************/ -#if defined(__cplusplus) -extern "C" { -#endif /* __cplusplus*/ - -/*! - * @brief This function executes configuration of clocks. - * - */ -void BOARD_BootClockVLPR(void); - -#if defined(__cplusplus) -} -#endif /* __cplusplus*/ - -#endif /* _CLOCK_CONFIG_H_ */ diff --git a/hw/bsp/nrf/boards/pca10095/board.cmake b/hw/bsp/nrf/boards/pca10095/board.cmake index 0fbc1d31f..ca5399a3a 100644 --- a/hw/bsp/nrf/boards/pca10095/board.cmake +++ b/hw/bsp/nrf/boards/pca10095/board.cmake @@ -1,9 +1,6 @@ set(MCU_VARIANT nrf5340_application) set(LD_FILE_GNU ${NRFX_DIR}/mdk/nrf5340_xxaa_application.ld) -# enable max3421 host driver for this board -set(MAX3421_HOST 1) - function(update_board TARGET) target_sources(${TARGET} PRIVATE ${NRFX_DIR}/drivers/src/nrfx_usbreg.c diff --git a/hw/bsp/nrf/boards/pca10095/board.h b/hw/bsp/nrf/boards/pca10095/board.h index 7437dad48..ad3379bf6 100644 --- a/hw/bsp/nrf/boards/pca10095/board.h +++ b/hw/bsp/nrf/boards/pca10095/board.h @@ -42,8 +42,8 @@ #define BUTTON_STATE_ACTIVE 0 // UART -#define UART_RX_PIN 22 -#define UART_TX_PIN 20 +#define UART_RX_PIN 32 +#define UART_TX_PIN 33 // SPI for USB host shield #define MAX3421_SCK_PIN _PINNUM(1, 15) diff --git a/hw/bsp/nrf/boards/pca10095/board.mk b/hw/bsp/nrf/boards/pca10095/board.mk index 20580d619..9c4edbafc 100644 --- a/hw/bsp/nrf/boards/pca10095/board.mk +++ b/hw/bsp/nrf/boards/pca10095/board.mk @@ -2,9 +2,6 @@ CPU_CORE = cortex-m33 MCU_VARIANT = nrf5340_application CFLAGS += -DNRF5340_XXAA -DNRF5340_XXAA_APPLICATION -# enable max3421 host driver for this board -MAX3421_HOST = 1 - LD_FILE = hw/mcu/nordic/nrfx/mdk/nrf5340_xxaa_application.ld SRC_C += hw/mcu/nordic/nrfx/drivers/src/nrfx_usbreg.c diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index 55119ef02..7a970f52e 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -76,7 +76,6 @@ enum { #define LFCLK_SRC_RC CLOCK_LFCLKSRC_SRC_LFRC #define VBUSDETECT_Msk USBREG_USBREGSTATUS_VBUSDETECT_Msk #define OUTPUTRDY_Msk USBREG_USBREGSTATUS_OUTPUTRDY_Msk - #define GPIOTE_IRQn GPIOTE1_IRQn #else #define LFCLK_SRC_RC CLOCK_LFCLKSRC_SRC_RC #define VBUSDETECT_Msk POWER_USBREGSTATUS_VBUSDETECT_Msk diff --git a/src/class/msc/msc_device.c b/src/class/msc/msc_device.c index c145d86a6..2589dcd2c 100644 --- a/src/class/msc/msc_device.c +++ b/src/class/msc/msc_device.c @@ -203,7 +203,7 @@ uint8_t rdwr10_validate_cmd(msc_cbw_t const* cbw) //--------------------------------------------------------------------+ // Debug //--------------------------------------------------------------------+ -#if CFG_TUSB_DEBUG >= CFG_TUD_MSC_LOG_LEVEL +#if CFG_TUSB_DEBUG >= 2 TU_ATTR_UNUSED tu_static tu_lookup_entry_t const _msc_scsi_cmd_lookup[] = { diff --git a/src/class/video/video.h b/src/class/video/video.h index abf1e34b9..6319c6536 100644 --- a/src/class/video/video.h +++ b/src/class/video/video.h @@ -368,8 +368,6 @@ typedef struct TU_ATTR_PACKED { uint8_t bCopyProtect; } tusb_desc_video_format_uncompressed_t; -TU_VERIFY_STATIC(sizeof(tusb_desc_video_format_uncompressed_t) == 27, "size is not correct"); - // Uncompressed payload specs: 3.1.2 frame descriptor #define tusb_desc_video_frame_uncompressed_nint_t(_nint) \ struct TU_ATTR_PACKED { \ @@ -383,7 +381,7 @@ TU_VERIFY_STATIC(sizeof(tusb_desc_video_format_uncompressed_t) == 27, "size is n uint32_t dwMinBitRate; \ uint32_t dwMaxBitRate; \ uint32_t dwMaxVideoFrameBufferSize; /* deprecated in 1.5 */ \ - uint32_t dwDefaultFrameInterval; /* 100ns unit */\ + uint32_t dwDefaultFrameInterval; \ uint8_t bFrameIntervalType; \ uint32_t dwFrameInterval[_nint]; \ } @@ -415,8 +413,6 @@ typedef struct TU_ATTR_PACKED { uint8_t bCopyProtect; } tusb_desc_video_format_mjpeg_t; -TU_VERIFY_STATIC(sizeof(tusb_desc_video_format_mjpeg_t) == 11, "size is not correct"); - // MJPEG payload specs: 3.1.2 frame descriptor (same as uncompressed) typedef tusb_desc_video_frame_uncompressed_t tusb_desc_video_frame_mjpeg_t; typedef tusb_desc_video_frame_uncompressed_1int_t tusb_desc_video_frame_mjpeg_1int_t; diff --git a/src/class/video/video_device.c b/src/class/video/video_device.c index c33dfa0b0..1affd615e 100644 --- a/src/class/video/video_device.c +++ b/src/class/video/video_device.c @@ -559,7 +559,6 @@ static bool _negotiate_streaming_parameters(videod_streaming_interface_t const * uint_fast8_t num_intervals = frm->uncompressed.bFrameIntervalType; if (num_intervals) { interval = 0; - interval_ms = 0; } else { interval = frm->uncompressed.dwFrameInterval[2]; interval_ms = interval / 10000; diff --git a/src/common/tusb_debug.h b/src/common/tusb_debug.h index 2e9f1d9cd..0f4dc93f3 100644 --- a/src/common/tusb_debug.h +++ b/src/common/tusb_debug.h @@ -60,7 +60,6 @@ void tu_print_mem(void const *buf, uint32_t count, uint8_t indent); static inline void tu_print_buf(uint8_t const* buf, uint32_t bufsize) { for(uint32_t i=0; i= 2 diff --git a/src/common/tusb_fifo.c b/src/common/tusb_fifo.c index 76696396b..d6c3db4ce 100644 --- a/src/common/tusb_fifo.c +++ b/src/common/tusb_fifo.c @@ -224,7 +224,6 @@ static void _ff_push_n(tu_fifo_t* f, void const * app_buf, uint16_t n, uint16_t if (wrap_bytes > 0) _ff_push_const_addr(ff_buf, app_buf, wrap_bytes); } break; - default: break; } } diff --git a/src/device/usbd.c b/src/device/usbd.c index be85d7769..5c94ebcc5 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -500,6 +500,7 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) case DCD_EVENT_SETUP_RECEIVED: TU_LOG_BUF(CFG_TUD_LOG_LEVEL, &event.setup_received, 8); + TU_LOG_USBD("\r\n"); // Mark as connected after receiving 1st setup packet. // But it is easier to set it every time instead of wasting time to check then set diff --git a/src/host/usbh.c b/src/host/usbh.c index f56290a0c..dfe6ddb42 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -343,12 +343,12 @@ bool tuh_init(uint8_t controller_id) { if ( tuh_inited() ) return true; TU_LOG_USBH("USBH init on controller %u\r\n", controller_id); - TU_LOG_INT_USBH(sizeof(usbh_device_t)); - TU_LOG_INT_USBH(sizeof(hcd_event_t)); - TU_LOG_INT_USBH(sizeof(_ctrl_xfer)); - TU_LOG_INT_USBH(sizeof(tuh_xfer_t)); - TU_LOG_INT_USBH(sizeof(tu_fifo_t)); - TU_LOG_INT_USBH(sizeof(tu_edpt_stream_t)); + TU_LOG_INT(CFG_TUH_LOG_LEVEL, sizeof(usbh_device_t)); + TU_LOG_INT(CFG_TUH_LOG_LEVEL, sizeof(hcd_event_t)); + TU_LOG_INT(CFG_TUH_LOG_LEVEL, sizeof(_ctrl_xfer)); + TU_LOG_INT(CFG_TUH_LOG_LEVEL, sizeof(tuh_xfer_t)); + TU_LOG_INT(CFG_TUH_LOG_LEVEL, sizeof(tu_fifo_t)); + TU_LOG_INT(CFG_TUH_LOG_LEVEL, sizeof(tu_edpt_stream_t)); // Event queue _usbh_q = osal_queue_create( &_usbh_qdef ); @@ -588,7 +588,8 @@ bool tuh_control_xfer (tuh_xfer_t* xfer) { TU_LOG_USBH("[%u:%u] %s: ", rhport, daddr, (xfer->setup->bmRequestType_bit.type == TUSB_REQ_TYPE_STANDARD && xfer->setup->bRequest <= TUSB_REQ_SYNCH_FRAME) ? tu_str_std_request[xfer->setup->bRequest] : "Class Request"); - TU_LOG_BUF_USBH(xfer->setup, 8); + TU_LOG_BUF(CFG_TUH_LOG_LEVEL, xfer->setup, 8); + TU_LOG_USBH("\r\n"); if (xfer->complete_cb) { TU_ASSERT( hcd_setup_send(rhport, daddr, (uint8_t const*) &_ctrl_xfer.request) ); @@ -659,8 +660,9 @@ static bool usbh_control_xfer_cb (uint8_t dev_addr, uint8_t ep_addr, xfer_result tusb_control_request_t const * request = &_ctrl_xfer.request; if (XFER_RESULT_SUCCESS != result) { - TU_LOG_USBH("[%u:%u] Control %s, xferred_bytes = %lu\r\n", rhport, dev_addr, result == XFER_RESULT_STALLED ? "STALLED" : "FAILED", xferred_bytes); - TU_LOG_BUF_USBH(request, 8); + TU_LOG1("[%u:%u] Control %s, xferred_bytes = %lu\r\n", rhport, dev_addr, result == XFER_RESULT_STALLED ? "STALLED" : "FAILED", xferred_bytes); + TU_LOG1_BUF(request, 8); + TU_LOG1("\r\n"); // terminate transfer if any stage failed _xfer_complete(dev_addr, result); @@ -678,7 +680,7 @@ static bool usbh_control_xfer_cb (uint8_t dev_addr, uint8_t ep_addr, xfer_result case CONTROL_STAGE_DATA: if (request->wLength) { TU_LOG_USBH("[%u:%u] Control data:\r\n", rhport, dev_addr); - TU_LOG_MEM_USBH(_ctrl_xfer.buffer, xferred_bytes, 2); + TU_LOG_MEM(CFG_TUH_LOG_LEVEL, _ctrl_xfer.buffer, xferred_bytes, 2); } _ctrl_xfer.actual_len = (uint16_t) xferred_bytes; diff --git a/src/host/usbh_pvt.h b/src/host/usbh_pvt.h index 4ed2a72b5..4a97a1c18 100644 --- a/src/host/usbh_pvt.h +++ b/src/host/usbh_pvt.h @@ -35,11 +35,7 @@ extern "C" { #endif -#define TU_LOG_USBH(...) TU_LOG(CFG_TUH_LOG_LEVEL, __VA_ARGS__) -#define TU_LOG_MEM_USBH(...) TU_LOG_MEM(CFG_TUH_LOG_LEVEL, __VA_ARGS__) -#define TU_LOG_BUF_USBH(...) TU_LOG_BUF(CFG_TUH_LOG_LEVEL, __VA_ARGS__) -#define TU_LOG_INT_USBH(...) TU_LOG_INT(CFG_TUH_LOG_LEVEL, __VA_ARGS__) -#define TU_LOG_HEX_USBH(...) TU_LOG_HEX(CFG_TUH_LOG_LEVEL, __VA_ARGS__) +#define TU_LOG_USBH(...) TU_LOG(CFG_TUH_LOG_LEVEL, __VA_ARGS__) enum { USBH_EPSIZE_BULK_MAX = (TUH_OPT_HIGH_SPEED ? TUSB_EPSIZE_BULK_HS : TUSB_EPSIZE_BULK_FS) diff --git a/src/portable/nordic/nrf5x/dcd_nrf5x.c b/src/portable/nordic/nrf5x/dcd_nrf5x.c index 841cda752..4e702aed4 100644 --- a/src/portable/nordic/nrf5x/dcd_nrf5x.c +++ b/src/portable/nordic/nrf5x/dcd_nrf5x.c @@ -653,11 +653,7 @@ void dcd_int_handler(uint8_t rhport) if (NRF_USBD->EPOUTEN & USBD_EPOUTEN_ISOOUT_Msk) { iso_enabled = true; - // Transfer from endpoint to RAM only if data is not corrupted - if ((int_status & USBD_INTEN_USBEVENT_Msk) == 0 || - (NRF_USBD->EVENTCAUSE & USBD_EVENTCAUSE_ISOOUTCRC_Msk) == 0) { - xact_out_dma(EP_ISO_NUM); - } + xact_out_dma(EP_ISO_NUM); } // ISOIN: Notify client that data was transferred @@ -687,7 +683,7 @@ void dcd_int_handler(uint8_t rhport) { TU_LOG(2, "EVENTCAUSE = 0x%04lX\r\n", NRF_USBD->EVENTCAUSE); - enum { EVT_CAUSE_MASK = USBD_EVENTCAUSE_SUSPEND_Msk | USBD_EVENTCAUSE_RESUME_Msk | USBD_EVENTCAUSE_USBWUALLOWED_Msk | USBD_EVENTCAUSE_ISOOUTCRC_Msk }; + enum { EVT_CAUSE_MASK = USBD_EVENTCAUSE_SUSPEND_Msk | USBD_EVENTCAUSE_RESUME_Msk | USBD_EVENTCAUSE_USBWUALLOWED_Msk }; uint32_t const evt_cause = NRF_USBD->EVENTCAUSE & EVT_CAUSE_MASK; NRF_USBD->EVENTCAUSE = evt_cause; // clear interrupt diff --git a/src/portable/ohci/ohci.h b/src/portable/ohci/ohci.h index 94bad5df7..4feefd771 100644 --- a/src/portable/ohci/ohci.h +++ b/src/portable/ohci/ohci.h @@ -83,7 +83,7 @@ typedef struct TU_ATTR_ALIGNED(16) volatile uint32_t condition_code : 4; // Word 1 - uint8_t* volatile current_buffer_pointer; + volatile uint8_t* current_buffer_pointer; // Word 2 : next TD volatile uint32_t next; -- cgit v1.3.1 From 3d3bf45102ded992fc10be09f3e9b9c981379ad1 Mon Sep 17 00:00:00 2001 From: hathach Date: Sat, 24 Feb 2024 00:36:07 +0700 Subject: frdm k64f usb work well, add kinetis_k to ci cmake --- .github/workflows/cmake_arm.yml | 2 +- hw/bsp/kinetis_k/boards/frdm_k64f/frdm_k64f.mex | 43 +++++++++++++++++++++++-- hw/bsp/kinetis_k/family.c | 4 ++- hw/bsp/kinetis_k/family.cmake | 1 + hw/bsp/kinetis_k/family.mk | 1 + src/portable/chipidea/ci_fs/ci_fs_kinetis.h | 6 ++-- src/portable/chipidea/ci_fs/dcd_ci_fs.c | 8 +++++ src/portable/nxp/khci/dcd_khci.c | 14 +++----- 8 files changed, 60 insertions(+), 19 deletions(-) (limited to 'src/portable') diff --git a/.github/workflows/cmake_arm.yml b/.github/workflows/cmake_arm.yml index f97645ad1..80ab1ea71 100644 --- a/.github/workflows/cmake_arm.yml +++ b/.github/workflows/cmake_arm.yml @@ -38,7 +38,7 @@ jobs: family: # Alphabetical order - 'imxrt' - - 'kinetis_kl' + - 'kinetis_k kinetis_kl' - 'lpc17 lpc18 lpc40 lpc43' - 'lpc54 lpc55' - 'mcx' diff --git a/hw/bsp/kinetis_k/boards/frdm_k64f/frdm_k64f.mex b/hw/bsp/kinetis_k/boards/frdm_k64f/frdm_k64f.mex index 28d1ea612..4a8c77f95 100644 --- a/hw/bsp/kinetis_k/boards/frdm_k64f/frdm_k64f.mex +++ b/hw/bsp/kinetis_k/boards/frdm_k64f/frdm_k64f.mex @@ -732,15 +732,27 @@ - + - true + true + + + + + 2.8.0 + + + + + + + 14.0.0 @@ -755,6 +767,31 @@ true + + + true + + + + + true + + + + + 0 + + + + + true + + + + + true + + @@ -789,7 +826,7 @@ - + diff --git a/hw/bsp/kinetis_k/family.c b/hw/bsp/kinetis_k/family.c index 38cfc45e3..6df29c1fc 100644 --- a/hw/bsp/kinetis_k/family.c +++ b/hw/bsp/kinetis_k/family.c @@ -30,6 +30,7 @@ #include "fsl_port.h" #include "fsl_clock.h" #include "fsl_uart.h" +#include "fsl_sysmpu.h" #include "board/clock_config.h" #include "board/pin_mux.h" @@ -50,6 +51,7 @@ void board_init(void) { BOARD_InitBootPins(); BOARD_BootClockRUN(); SystemCoreClockUpdate(); + SYSMPU_Enable(SYSMPU, 0); #if CFG_TUSB_OS == OPT_OS_NONE // 1ms tick timer @@ -84,7 +86,7 @@ void board_init(void) { #endif // USB - CLOCK_EnableUsbfs0Clock(kCLOCK_UsbSrcPll0, CLOCK_GetFreq(kCLOCK_PllFllSelClk)); + // USB clock is configured in BOARD_BootClockRUN() } //--------------------------------------------------------------------+ diff --git a/hw/bsp/kinetis_k/family.cmake b/hw/bsp/kinetis_k/family.cmake index 6d642c101..e0b5fcfc8 100644 --- a/hw/bsp/kinetis_k/family.cmake +++ b/hw/bsp/kinetis_k/family.cmake @@ -40,6 +40,7 @@ function(add_board_target BOARD_TARGET) ${SDK_DIR}/drivers/gpio ${SDK_DIR}/drivers/port ${SDK_DIR}/drivers/smc + ${SDK_DIR}/drivers/sysmpu ${SDK_DIR}/drivers/uart ) diff --git a/hw/bsp/kinetis_k/family.mk b/hw/bsp/kinetis_k/family.mk index de352a6a9..995873eec 100644 --- a/hw/bsp/kinetis_k/family.mk +++ b/hw/bsp/kinetis_k/family.mk @@ -29,6 +29,7 @@ INC += \ $(TOP)/$(SDK_DIR)/drivers/gpio \ $(TOP)/$(SDK_DIR)/drivers/port \ $(TOP)/$(SDK_DIR)/drivers/smc \ + $(TOP)/$(SDK_DIR)/drivers/sysmpu \ $(TOP)/$(SDK_DIR)/drivers/uart \ SRC_S += ${SDK_DIR}/devices/${MCU_VARIANT}/gcc/startup_${MCU_VARIANT}.S diff --git a/src/portable/chipidea/ci_fs/ci_fs_kinetis.h b/src/portable/chipidea/ci_fs/ci_fs_kinetis.h index cd21af1c7..31e14a546 100644 --- a/src/portable/chipidea/ci_fs/ci_fs_kinetis.h +++ b/src/portable/chipidea/ci_fs/ci_fs_kinetis.h @@ -36,14 +36,12 @@ #define CI_FS_REG(_port) ((ci_fs_regs_t*) USB0_BASE) #define CI_REG CI_FS_REG(0) -void dcd_int_enable(uint8_t rhport) -{ +void dcd_int_enable(uint8_t rhport) { (void) rhport; NVIC_EnableIRQ(USB0_IRQn); } -void dcd_int_disable(uint8_t rhport) -{ +void dcd_int_disable(uint8_t rhport) { (void) rhport; NVIC_DisableIRQ(USB0_IRQn); } diff --git a/src/portable/chipidea/ci_fs/dcd_ci_fs.c b/src/portable/chipidea/ci_fs/dcd_ci_fs.c index 9327e09d8..4b1d488b5 100644 --- a/src/portable/chipidea/ci_fs/dcd_ci_fs.c +++ b/src/portable/chipidea/ci_fs/dcd_ci_fs.c @@ -271,9 +271,17 @@ void dcd_init(uint8_t rhport) { (void) rhport; + // save crystal-less setting (recovery clock) + uint32_t clk_recover_irc_en = CI_REG->CLK_RECOVER_IRC_EN; + uint32_t clk_recover_ctrl = CI_REG->CLK_RECOVER_CTRL;; + CI_REG->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; while (CI_REG->USBTRC0 & USB_USBTRC0_USBRESET_MASK); + // restore crystal-less setting + CI_REG->CLK_RECOVER_IRC_EN = clk_recover_irc_en; + CI_REG->CLK_RECOVER_CTRL |= clk_recover_ctrl; + tu_memclr(&_dcd, sizeof(_dcd)); CI_REG->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ CI_REG->BDT_PAGE1 = (uint8_t)((uintptr_t)_dcd.bdt >> 8); diff --git a/src/portable/nxp/khci/dcd_khci.c b/src/portable/nxp/khci/dcd_khci.c index 5a2f768b3..5d04a524a 100644 --- a/src/portable/nxp/khci/dcd_khci.c +++ b/src/portable/nxp/khci/dcd_khci.c @@ -269,22 +269,16 @@ void dcd_init(uint8_t rhport) { (void) rhport; -#if (CFG_TUSB_MCU == OPT_MCU_KINETIS_K) - uint32_t clk_recover_irc_en; - uint32_t clk_recover_ctrl; - - clk_recover_irc_en = KHCI->CLK_RECOVER_IRC_EN; - clk_recover_ctrl = KHCI->CLK_RECOVER_CTRL; + // save crystal-less setting (recovery clock) + uint32_t clk_recover_irc_en = KHCI->CLK_RECOVER_IRC_EN; + uint32_t clk_recover_ctrl = KHCI->CLK_RECOVER_CTRL; KHCI->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; while (KHCI->USBTRC0 & USB_USBTRC0_USBRESET_MASK); + // restore crystal-less setting KHCI->CLK_RECOVER_IRC_EN = clk_recover_irc_en; KHCI->CLK_RECOVER_CTRL |= clk_recover_ctrl; -#else - KHCI->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; - while (KHCI->USBTRC0 & USB_USBTRC0_USBRESET_MASK); -#endif tu_memclr(&_dcd, sizeof(_dcd)); KHCI->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ -- cgit v1.3.1 From 65a2e5cdf8d708b88bb8edf7b718f698e5a18ffc Mon Sep 17 00:00:00 2001 From: hathach Date: Sat, 24 Feb 2024 00:53:05 +0700 Subject: fix build with cpu without USB_CLK_RECOVER using old dcd_khci driver --- .idea/cmake.xml | 2 +- src/portable/nxp/khci/dcd_khci.c | 4 ++++ 2 files changed, 5 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/.idea/cmake.xml b/.idea/cmake.xml index dbb34aaab..ebc6a0570 100644 --- a/.idea/cmake.xml +++ b/.idea/cmake.xml @@ -59,7 +59,7 @@ - + diff --git a/src/portable/nxp/khci/dcd_khci.c b/src/portable/nxp/khci/dcd_khci.c index 5d04a524a..3419c2565 100644 --- a/src/portable/nxp/khci/dcd_khci.c +++ b/src/portable/nxp/khci/dcd_khci.c @@ -270,15 +270,19 @@ void dcd_init(uint8_t rhport) (void) rhport; // save crystal-less setting (recovery clock) + #ifdef USB_CLK_RECOVER_IRC_EN_IRC_EN uint32_t clk_recover_irc_en = KHCI->CLK_RECOVER_IRC_EN; uint32_t clk_recover_ctrl = KHCI->CLK_RECOVER_CTRL; + #endif KHCI->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; while (KHCI->USBTRC0 & USB_USBTRC0_USBRESET_MASK); // restore crystal-less setting + #ifdef USB_CLK_RECOVER_IRC_EN_IRC_EN KHCI->CLK_RECOVER_IRC_EN = clk_recover_irc_en; KHCI->CLK_RECOVER_CTRL |= clk_recover_ctrl; + #endif tu_memclr(&_dcd, sizeof(_dcd)); KHCI->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ -- cgit v1.3.1 From a52b4647ec20414bbfde986c13a18598ffd426d6 Mon Sep 17 00:00:00 2001 From: hathach Date: Sat, 24 Feb 2024 17:18:30 +0700 Subject: only save/restore CLK_RECOVER_IRC_EN/CTRL if FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED is defined to 1 --- src/portable/chipidea/ci_fs/dcd_ci_fs.c | 10 +++++++--- src/portable/nxp/khci/dcd_khci.c | 8 ++++---- 2 files changed, 11 insertions(+), 7 deletions(-) (limited to 'src/portable') diff --git a/src/portable/chipidea/ci_fs/dcd_ci_fs.c b/src/portable/chipidea/ci_fs/dcd_ci_fs.c index 4b1d488b5..a68ecf8c9 100644 --- a/src/portable/chipidea/ci_fs/dcd_ci_fs.c +++ b/src/portable/chipidea/ci_fs/dcd_ci_fs.c @@ -271,16 +271,20 @@ void dcd_init(uint8_t rhport) { (void) rhport; - // save crystal-less setting (recovery clock) + // save crystal-less setting (if available) + #if defined(FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED) && FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED == 1 uint32_t clk_recover_irc_en = CI_REG->CLK_RECOVER_IRC_EN; - uint32_t clk_recover_ctrl = CI_REG->CLK_RECOVER_CTRL;; + uint32_t clk_recover_ctrl = CI_REG->CLK_RECOVER_CTRL; + #endif CI_REG->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; while (CI_REG->USBTRC0 & USB_USBTRC0_USBRESET_MASK); - // restore crystal-less setting + // restore crystal-less setting (if available) + #if defined(FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED) && FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED == 1 CI_REG->CLK_RECOVER_IRC_EN = clk_recover_irc_en; CI_REG->CLK_RECOVER_CTRL |= clk_recover_ctrl; + #endif tu_memclr(&_dcd, sizeof(_dcd)); CI_REG->USBTRC0 |= TU_BIT(6); /* software must set this bit to 1 */ diff --git a/src/portable/nxp/khci/dcd_khci.c b/src/portable/nxp/khci/dcd_khci.c index 3419c2565..dc71117b3 100644 --- a/src/portable/nxp/khci/dcd_khci.c +++ b/src/portable/nxp/khci/dcd_khci.c @@ -269,8 +269,8 @@ void dcd_init(uint8_t rhport) { (void) rhport; - // save crystal-less setting (recovery clock) - #ifdef USB_CLK_RECOVER_IRC_EN_IRC_EN + // save crystal-less setting (if available) + #if defined(FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED) && FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED == 1 uint32_t clk_recover_irc_en = KHCI->CLK_RECOVER_IRC_EN; uint32_t clk_recover_ctrl = KHCI->CLK_RECOVER_CTRL; #endif @@ -278,8 +278,8 @@ void dcd_init(uint8_t rhport) KHCI->USBTRC0 |= USB_USBTRC0_USBRESET_MASK; while (KHCI->USBTRC0 & USB_USBTRC0_USBRESET_MASK); - // restore crystal-less setting - #ifdef USB_CLK_RECOVER_IRC_EN_IRC_EN + // restore crystal-less setting (if available) + #if defined(FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED) && FSL_FEATURE_USB_KHCI_IRC48M_MODULE_CLOCK_ENABLED == 1 KHCI->CLK_RECOVER_IRC_EN = clk_recover_irc_en; KHCI->CLK_RECOVER_CTRL |= clk_recover_ctrl; #endif -- cgit v1.3.1 From 473d400cfde768e26fe8644bab3d655c81777b64 Mon Sep 17 00:00:00 2001 From: Taylor Yu Date: Sun, 25 Feb 2024 11:12:24 -0600 Subject: work around possible RP2040 erratum RP2040 device controller does not seem to clear pending transactions configured in EP0 buffer controls when the host aborts a control transfer. This causes assertion failures, including when a buffer AVAILABLE flag set for a previous transfer causes an unexpected transaction completion. --- src/portable/raspberrypi/rp2040/dcd_rp2040.c | 31 ++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) (limited to 'src/portable') diff --git a/src/portable/raspberrypi/rp2040/dcd_rp2040.c b/src/portable/raspberrypi/rp2040/dcd_rp2040.c index e8cee73fd..51174f709 100644 --- a/src/portable/raspberrypi/rp2040/dcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/dcd_rp2040.c @@ -217,6 +217,18 @@ static void __tusb_irq_path_func(hw_handle_buff_status)(void) TU_ATTR_ALWAYS_INLINE static inline void reset_ep0_pid(void) { + // Abort any transactions from a prior control transfer, because + // receiving SETUP doesn't reset buffer control state. This works around + // a possible USB hardware erratum. + + // With this workaround a race window still exists, but smaller. + // ABORT flag is unusable prior to hardware B2 (RP2040-E2), so a larger + // race window exists for B1 and earlier. + if (rp2040_chip_version() >= 2) { + usb_hw_set->abort = 0x3; + while ((usb_hw->abort_done & 0x3) != 0x3) + ; + } // If we have finished this transfer on EP0 set pid back to 1 for next // setup transfer. Also clear a stall in case uint8_t addrs[] = {0x0, 0x80}; @@ -224,6 +236,25 @@ TU_ATTR_ALWAYS_INLINE static inline void reset_ep0_pid(void) { struct hw_endpoint *ep = hw_endpoint_get_by_addr(addrs[i]); ep->next_pid = 1u; + // Reset the buffer control now to minimize race conditions + _hw_endpoint_buffer_control_set_value32(ep, USB_BUF_CTRL_DATA1_PID | USB_BUF_CTRL_SEL); + // Explicit delay, because the one in + // _hw_endpoint_buffer_control_set_value32 is only to set AVAILABLE + __asm volatile ( + "b 1f\n" + "1: b 1f\n" + "1: b 1f\n" + "1: b 1f\n" + "1: b 1f\n" + "1: b 1f\n" + "1:\n" + : : : "memory"); + // Make sure local ep state matches peripheral + hw_endpoint_reset_transfer(ep); + } + if (rp2040_chip_version() >= 2) { + usb_hw_clear->abort = 0x3; + usb_hw_clear->abort_done = 0x3; } } -- cgit v1.3.1 From eed37476612b6c2074cc3cdabbdef88c59822114 Mon Sep 17 00:00:00 2001 From: Camila Date: Mon, 11 Mar 2024 13:11:07 +0100 Subject: Changes required for SDK 3.2.0: - Define EP_ALLOCREQ - Define EP_FREEREQ - Define EP_ALLOCBUFFER - Define EP_FREEBUFFER Those were previously defined in spresense-exported-sdk, but now have been removed. --- src/portable/sony/cxd56/dcd_cxd56.c | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) (limited to 'src/portable') diff --git a/src/portable/sony/cxd56/dcd_cxd56.c b/src/portable/sony/cxd56/dcd_cxd56.c index 6677891a5..9a939bc6c 100644 --- a/src/portable/sony/cxd56/dcd_cxd56.c +++ b/src/portable/sony/cxd56/dcd_cxd56.c @@ -39,6 +39,25 @@ #define CXD56_SETUP_QUEUE_DEPTH (4) #define CXD56_MAX_DATA_OUT_SIZE (64) +/* Allocate/free I/O requests. + * Should not be called from interrupt processing! + */ + +#define EP_ALLOCREQ(ep) (ep)->ops->allocreq(ep) +#define EP_FREEREQ(ep,req) (ep)->ops->freereq(ep,req) + +/* Allocate/free an I/O buffer. + * Should not be called from interrupt processing! + */ + +#ifdef CONFIG_USBDEV_DMA +# define EP_ALLOCBUFFER(ep,nb) (ep)->ops->allocbuffer(ep,nb) +# define EP_FREEBUFFER(ep,buf) (ep)->ops->freebuffer(ep,buf) +#else +# define EP_ALLOCBUFFER(ep,nb) kmm_malloc(nb) +# define EP_FREEBUFFER(ep,buf) kmm_free(buf) +#endif + OSAL_QUEUE_DEF(usbd_int_set, _setup_queue_def, CXD56_SETUP_QUEUE_DEPTH, struct usb_ctrlreq_s); struct usbdcd_driver_s -- cgit v1.3.1 From 56532321443ed1ada8c2f33bd9eb6f075da66394 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 5 Mar 2024 19:43:37 +0700 Subject: reformat code --- src/device/usbd.c | 306 +++++++++---------------- src/portable/raspberrypi/rp2040/dcd_rp2040.c | 330 +++++++++++---------------- src/portable/raspberrypi/rp2040/rp2040_usb.c | 167 ++++++-------- 3 files changed, 316 insertions(+), 487 deletions(-) (limited to 'src/portable') diff --git a/src/device/usbd.c b/src/device/usbd.c index be85d7769..87542e9aa 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -372,10 +372,9 @@ bool tud_inited(void) { return _usbd_rhport != RHPORT_INVALID; } -bool tud_init (uint8_t rhport) -{ +bool tud_init(uint8_t rhport) { // skip if already initialized - if ( tud_inited() ) return true; + if (tud_inited()) return true; TU_LOG_USBD("USBD init on controller %u\r\n", rhport); TU_LOG_INT(CFG_TUD_LOG_LEVEL, sizeof(usbd_device_t)); @@ -395,15 +394,13 @@ bool tud_init (uint8_t rhport) TU_ASSERT(_usbd_q); // Get application driver if available - if ( usbd_app_driver_get_cb ) - { + if (usbd_app_driver_get_cb) { _app_driver = usbd_app_driver_get_cb(&_app_driver_count); } // Init class drivers - for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) - { - usbd_class_driver_t const * driver = get_driver(i); + for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) { + usbd_class_driver_t const* driver = get_driver(i); TU_ASSERT(driver); TU_LOG_USBD("%s init\r\n", driver->name); driver->init(); @@ -418,31 +415,26 @@ bool tud_init (uint8_t rhport) return true; } -static void configuration_reset(uint8_t rhport) -{ - for ( uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++ ) - { - usbd_class_driver_t const * driver = get_driver(i); - TU_ASSERT(driver, ); +static void configuration_reset(uint8_t rhport) { + for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) { + usbd_class_driver_t const* driver = get_driver(i); + TU_ASSERT(driver,); driver->reset(rhport); } tu_varclr(&_usbd_dev); memset(_usbd_dev.itf2drv, DRVID_INVALID, sizeof(_usbd_dev.itf2drv)); // invalid mapping - memset(_usbd_dev.ep2drv , DRVID_INVALID, sizeof(_usbd_dev.ep2drv )); // invalid mapping + memset(_usbd_dev.ep2drv, DRVID_INVALID, sizeof(_usbd_dev.ep2drv)); // invalid mapping } -static void usbd_reset(uint8_t rhport) -{ +static void usbd_reset(uint8_t rhport) { configuration_reset(rhport); usbd_control_reset(); } -bool tud_task_event_ready(void) -{ +bool tud_task_event_ready(void) { // Skip if stack is not initialized - if ( !tud_inited() ) return false; - + if (!tud_inited()) return false; return !osal_queue_empty(_usbd_q); } @@ -450,53 +442,44 @@ bool tud_task_event_ready(void) * This top level thread manages all device controller event and delegates events to class-specific drivers. * This should be called periodically within the mainloop or rtos thread. * - @code - int main(void) - { + int main(void) { application_init(); tusb_init(); - while(1) // the mainloop - { + while(1) { // the mainloop application_code(); tud_task(); // tinyusb device task } } - @endcode */ -void tud_task_ext(uint32_t timeout_ms, bool in_isr) -{ +void tud_task_ext(uint32_t timeout_ms, bool in_isr) { (void) in_isr; // not implemented yet // Skip if stack is not initialized - if ( !tud_inited() ) return; + if (!tud_inited()) return; // Loop until there is no more events in the queue - while (1) - { + while (1) { dcd_event_t event; - if ( !osal_queue_receive(_usbd_q, &event, timeout_ms) ) return; + if (!osal_queue_receive(_usbd_q, &event, timeout_ms)) return; #if CFG_TUSB_DEBUG >= CFG_TUD_LOG_LEVEL if (event.event_id == DCD_EVENT_SETUP_RECEIVED) TU_LOG_USBD("\r\n"); // extra line for setup TU_LOG_USBD("USBD %s ", event.event_id < DCD_EVENT_COUNT ? _usbd_event_str[event.event_id] : "CORRUPTED"); #endif - switch ( event.event_id ) - { + switch (event.event_id) { case DCD_EVENT_BUS_RESET: TU_LOG_USBD(": %s Speed\r\n", tu_str_speed[event.bus_reset.speed]); usbd_reset(event.rhport); _usbd_dev.speed = event.bus_reset.speed; - break; + break; case DCD_EVENT_UNPLUGGED: TU_LOG_USBD("\r\n"); usbd_reset(event.rhport); - - // invoke callback if (tud_umount_cb) tud_umount_cb(); - break; + break; case DCD_EVENT_SETUP_RECEIVED: TU_LOG_BUF(CFG_TUD_LOG_LEVEL, &event.setup_received, 8); @@ -508,81 +491,72 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) // mark both in & out control as free _usbd_dev.ep_status[0][TUSB_DIR_OUT].busy = 0; _usbd_dev.ep_status[0][TUSB_DIR_OUT].claimed = 0; - _usbd_dev.ep_status[0][TUSB_DIR_IN ].busy = 0; - _usbd_dev.ep_status[0][TUSB_DIR_IN ].claimed = 0; + _usbd_dev.ep_status[0][TUSB_DIR_IN].busy = 0; + _usbd_dev.ep_status[0][TUSB_DIR_IN].claimed = 0; // Process control request - if ( !process_control_request(event.rhport, &event.setup_received) ) - { + if (!process_control_request(event.rhport, &event.setup_received)) { TU_LOG_USBD(" Stall EP0\r\n"); // Failed -> stall both control endpoint IN and OUT dcd_edpt_stall(event.rhport, 0); dcd_edpt_stall(event.rhport, 0 | TUSB_DIR_IN_MASK); } - break; + break; - case DCD_EVENT_XFER_COMPLETE: - { + case DCD_EVENT_XFER_COMPLETE: { // Invoke the class callback associated with the endpoint address uint8_t const ep_addr = event.xfer_complete.ep_addr; - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const ep_dir = tu_edpt_dir(ep_addr); + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const ep_dir = tu_edpt_dir(ep_addr); TU_LOG_USBD("on EP %02X with %u bytes\r\n", ep_addr, (unsigned int) event.xfer_complete.len); _usbd_dev.ep_status[epnum][ep_dir].busy = 0; _usbd_dev.ep_status[epnum][ep_dir].claimed = 0; - if ( 0 == epnum ) - { - usbd_control_xfer_cb(event.rhport, ep_addr, (xfer_result_t) event.xfer_complete.result, event.xfer_complete - .len); - } - else - { - usbd_class_driver_t const * driver = get_driver( _usbd_dev.ep2drv[epnum][ep_dir] ); - TU_ASSERT(driver, ); + if (0 == epnum) { + usbd_control_xfer_cb(event.rhport, ep_addr, (xfer_result_t) event.xfer_complete.result, + event.xfer_complete.len); + } else { + usbd_class_driver_t const* driver = get_driver(_usbd_dev.ep2drv[epnum][ep_dir]); + TU_ASSERT(driver,); TU_LOG_USBD(" %s xfer callback\r\n", driver->name); driver->xfer_cb(event.rhport, ep_addr, (xfer_result_t) event.xfer_complete.result, event.xfer_complete.len); } + break; } - break; case DCD_EVENT_SUSPEND: // NOTE: When plugging/unplugging device, the D+/D- state are unstable and // can accidentally meet the SUSPEND condition ( Bus Idle for 3ms ), which result in a series of event // e.g suspend -> resume -> unplug/plug. Skip suspend/resume if not connected - if ( _usbd_dev.connected ) - { + if (_usbd_dev.connected) { TU_LOG_USBD(": Remote Wakeup = %u\r\n", _usbd_dev.remote_wakeup_en); if (tud_suspend_cb) tud_suspend_cb(_usbd_dev.remote_wakeup_en); - }else - { + } else { TU_LOG_USBD(" Skipped\r\n"); } - break; + break; case DCD_EVENT_RESUME: - if ( _usbd_dev.connected ) - { + if (_usbd_dev.connected) { TU_LOG_USBD("\r\n"); if (tud_resume_cb) tud_resume_cb(); - }else - { + } else { TU_LOG_USBD(" Skipped\r\n"); } - break; + break; case USBD_EVENT_FUNC_CALL: TU_LOG_USBD("\r\n"); - if ( event.func_call.func ) event.func_call.func(event.func_call.param); - break; + if (event.func_call.func) event.func_call.func(event.func_call.param); + break; case DCD_EVENT_SOF: default: TU_BREAKPOINT(); - break; + break; } #if CFG_TUSB_OS != OPT_OS_NONE && CFG_TUSB_OS != OPT_OS_PICO @@ -597,8 +571,7 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) //--------------------------------------------------------------------+ // Helper to invoke class driver control request handler -static bool invoke_class_control(uint8_t rhport, usbd_class_driver_t const * driver, tusb_control_request_t const * request) -{ +static bool invoke_class_control(uint8_t rhport, usbd_class_driver_t const * driver, tusb_control_request_t const * request) { usbd_control_set_complete_callback(driver->control_xfer_cb); TU_LOG_USBD(" %s control request\r\n", driver->name); return driver->control_xfer_cb(rhport, CONTROL_STAGE_SETUP, request); @@ -606,15 +579,12 @@ static bool invoke_class_control(uint8_t rhport, usbd_class_driver_t const * dri // This handles the actual request and its response. // return false will cause its caller to stall control endpoint -static bool process_control_request(uint8_t rhport, tusb_control_request_t const * p_request) -{ +static bool process_control_request(uint8_t rhport, tusb_control_request_t const * p_request) { usbd_control_set_complete_callback(NULL); - TU_ASSERT(p_request->bmRequestType_bit.type < TUSB_REQ_TYPE_INVALID); // Vendor request - if ( p_request->bmRequestType_bit.type == TUSB_REQ_TYPE_VENDOR ) - { + if ( p_request->bmRequestType_bit.type == TUSB_REQ_TYPE_VENDOR ) { TU_VERIFY(tud_vendor_control_xfer_cb); usbd_control_set_complete_callback(tud_vendor_control_xfer_cb); @@ -622,19 +592,16 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const } #if CFG_TUSB_DEBUG >= CFG_TUD_LOG_LEVEL - if (TUSB_REQ_TYPE_STANDARD == p_request->bmRequestType_bit.type && p_request->bRequest <= TUSB_REQ_SYNCH_FRAME) - { + if (TUSB_REQ_TYPE_STANDARD == p_request->bmRequestType_bit.type && p_request->bRequest <= TUSB_REQ_SYNCH_FRAME) { TU_LOG_USBD(" %s", tu_str_std_request[p_request->bRequest]); if (TUSB_REQ_GET_DESCRIPTOR != p_request->bRequest) TU_LOG_USBD("\r\n"); } #endif - switch ( p_request->bmRequestType_bit.recipient ) - { + switch ( p_request->bmRequestType_bit.recipient ) { //------------- Device Requests e.g in enumeration -------------// case TUSB_REQ_RCPT_DEVICE: - if ( TUSB_REQ_TYPE_CLASS == p_request->bmRequestType_bit.type ) - { + if ( TUSB_REQ_TYPE_CLASS == p_request->bmRequestType_bit.type ) { uint8_t const itf = tu_u16_low(p_request->wIndex); TU_VERIFY(itf < TU_ARRAY_SIZE(_usbd_dev.itf2drv)); @@ -645,15 +612,13 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const return invoke_class_control(rhport, driver, p_request); } - if ( TUSB_REQ_TYPE_STANDARD != p_request->bmRequestType_bit.type ) - { + if ( TUSB_REQ_TYPE_STANDARD != p_request->bmRequestType_bit.type ) { // Non standard request is not supported TU_BREAKPOINT(); return false; } - switch ( p_request->bRequest ) - { + switch ( p_request->bRequest ) { case TUSB_REQ_SET_ADDRESS: // Depending on mcu, status phase could be sent either before or after changing device address, // or even require stack to not response with status at all @@ -664,22 +629,18 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const _usbd_dev.addressed = 1; break; - case TUSB_REQ_GET_CONFIGURATION: - { + case TUSB_REQ_GET_CONFIGURATION: { uint8_t cfg_num = _usbd_dev.cfg_num; tud_control_xfer(rhport, p_request, &cfg_num, 1); } break; - case TUSB_REQ_SET_CONFIGURATION: - { + case TUSB_REQ_SET_CONFIGURATION: { uint8_t const cfg_num = (uint8_t) p_request->wValue; // Only process if new configure is different - if (_usbd_dev.cfg_num != cfg_num) - { - if ( _usbd_dev.cfg_num ) - { + if (_usbd_dev.cfg_num != cfg_num) { + if ( _usbd_dev.cfg_num ) { // already configured: need to clear all endpoints and driver first TU_LOG_USBD(" Clear current Configuration (%u) before switching\r\n", _usbd_dev.cfg_num); @@ -694,15 +655,11 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const } // Handle the new configuration and execute the corresponding callback - if ( cfg_num ) - { + if ( cfg_num ) { // switch to new configuration if not zero TU_ASSERT( process_set_config(rhport, cfg_num) ); - if ( tud_mount_cb ) tud_mount_cb(); - } - else - { + } else { if ( tud_umount_cb ) tud_umount_cb(); } } @@ -738,15 +695,14 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const tud_control_status(rhport, p_request); break; - case TUSB_REQ_GET_STATUS: - { + case TUSB_REQ_GET_STATUS: { // Device status bit mask // - Bit 0: Self Powered // - Bit 1: Remote Wakeup enabled uint16_t status = (uint16_t) ((_usbd_dev.self_powered ? 1u : 0u) | (_usbd_dev.remote_wakeup_en ? 2u : 0u)); tud_control_xfer(rhport, p_request, &status, 2); + break; } - break; // Unknown/Unsupported request default: TU_BREAKPOINT(); return false; @@ -754,8 +710,7 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const break; //------------- Class/Interface Specific Request -------------// - case TUSB_REQ_RCPT_INTERFACE: - { + case TUSB_REQ_RCPT_INTERFACE: { uint8_t const itf = tu_u16_low(p_request->wIndex); TU_VERIFY(itf < TU_ARRAY_SIZE(_usbd_dev.itf2drv)); @@ -764,25 +719,21 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const // all requests to Interface (STD or Class) is forwarded to class driver. // notable requests are: GET HID REPORT DESCRIPTOR, SET_INTERFACE, GET_INTERFACE - if ( !invoke_class_control(rhport, driver, p_request) ) - { + if ( !invoke_class_control(rhport, driver, p_request) ) { // For GET_INTERFACE and SET_INTERFACE, it is mandatory to respond even if the class // driver doesn't use alternate settings or implement this TU_VERIFY(TUSB_REQ_TYPE_STANDARD == p_request->bmRequestType_bit.type); - switch(p_request->bRequest) - { + switch(p_request->bRequest) { case TUSB_REQ_GET_INTERFACE: case TUSB_REQ_SET_INTERFACE: // Clear complete callback if driver set since it can also stall the request. usbd_control_set_complete_callback(NULL); - if (TUSB_REQ_GET_INTERFACE == p_request->bRequest) - { + if (TUSB_REQ_GET_INTERFACE == p_request->bRequest) { uint8_t alternate = 0; tud_control_xfer(rhport, p_request, &alternate, 1); - }else - { + }else { tud_control_status(rhport, p_request); } break; @@ -790,54 +741,42 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const default: return false; } } + break; } - break; //------------- Endpoint Request -------------// - case TUSB_REQ_RCPT_ENDPOINT: - { + case TUSB_REQ_RCPT_ENDPOINT: { uint8_t const ep_addr = tu_u16_low(p_request->wIndex); uint8_t const ep_num = tu_edpt_number(ep_addr); uint8_t const ep_dir = tu_edpt_dir(ep_addr); TU_ASSERT(ep_num < TU_ARRAY_SIZE(_usbd_dev.ep2drv) ); - usbd_class_driver_t const * driver = get_driver(_usbd_dev.ep2drv[ep_num][ep_dir]); - if ( TUSB_REQ_TYPE_STANDARD != p_request->bmRequestType_bit.type ) - { + if ( TUSB_REQ_TYPE_STANDARD != p_request->bmRequestType_bit.type ) { // Forward class request to its driver TU_VERIFY(driver); return invoke_class_control(rhport, driver, p_request); - } - else - { + } else { // Handle STD request to endpoint - switch ( p_request->bRequest ) - { - case TUSB_REQ_GET_STATUS: - { + switch ( p_request->bRequest ) { + case TUSB_REQ_GET_STATUS: { uint16_t status = usbd_edpt_stalled(rhport, ep_addr) ? 0x0001 : 0x0000; tud_control_xfer(rhport, p_request, &status, 2); } break; case TUSB_REQ_CLEAR_FEATURE: - case TUSB_REQ_SET_FEATURE: - { - if ( TUSB_REQ_FEATURE_EDPT_HALT == p_request->wValue ) - { - if ( TUSB_REQ_CLEAR_FEATURE == p_request->bRequest ) - { + case TUSB_REQ_SET_FEATURE: { + if ( TUSB_REQ_FEATURE_EDPT_HALT == p_request->wValue ) { + if ( TUSB_REQ_CLEAR_FEATURE == p_request->bRequest ) { usbd_edpt_clear_stall(rhport, ep_addr); - }else - { + }else { usbd_edpt_stall(rhport, ep_addr); } } - if (driver) - { + if (driver) { // Some classes such as USBTMC needs to clear/re-init its buffer when receiving CLEAR_FEATURE request // We will also forward std request targeted endpoint to class drivers as well @@ -853,14 +792,18 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const break; // Unknown/Unsupported request - default: TU_BREAKPOINT(); return false; + default: + TU_BREAKPOINT(); + return false; } } } break; // Unknown recipient - default: TU_BREAKPOINT(); return false; + default: + TU_BREAKPOINT(); + return false; } return true; @@ -1185,8 +1128,7 @@ void usbd_defer_func(osal_task_func_t func, void* param, bool in_isr) { // USBD Endpoint API //--------------------------------------------------------------------+ -bool usbd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * desc_ep) -{ +bool usbd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const* desc_ep) { rhport = _usbd_rhport; TU_ASSERT(tu_edpt_number(desc_ep->bEndpointAddress) < CFG_TUD_ENDPPOINT_MAX); @@ -1195,37 +1137,34 @@ bool usbd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const * desc_ep) return dcd_edpt_open(rhport, desc_ep); } -bool usbd_edpt_claim(uint8_t rhport, uint8_t ep_addr) -{ +bool usbd_edpt_claim(uint8_t rhport, uint8_t ep_addr) { (void) rhport; // TODO add this check later, also make sure we don't starve an out endpoint while suspending // TU_VERIFY(tud_ready()); - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); tu_edpt_state_t* ep_state = &_usbd_dev.ep_status[epnum][dir]; return tu_edpt_claim(ep_state, _usbd_mutex); } -bool usbd_edpt_release(uint8_t rhport, uint8_t ep_addr) -{ +bool usbd_edpt_release(uint8_t rhport, uint8_t ep_addr) { (void) rhport; - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); tu_edpt_state_t* ep_state = &_usbd_dev.ep_status[epnum][dir]; return tu_edpt_release(ep_state, _usbd_mutex); } -bool usbd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes) -{ +bool usbd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes) { rhport = _usbd_rhport; uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); // TODO skip ready() check for now since enumeration also use this API // TU_VERIFY(tud_ready()); @@ -1239,11 +1178,9 @@ bool usbd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t // could return and USBD task can preempt and clear the busy _usbd_dev.ep_status[epnum][dir].busy = 1; - if ( dcd_edpt_xfer(rhport, ep_addr, buffer, total_bytes) ) - { + if (dcd_edpt_xfer(rhport, ep_addr, buffer, total_bytes)) { return true; - }else - { + } else { // DCD error, mark endpoint as ready to allow next transfer _usbd_dev.ep_status[epnum][dir].busy = 0; _usbd_dev.ep_status[epnum][dir].claimed = 0; @@ -1257,12 +1194,11 @@ bool usbd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t // bytes should be written and second to keep the return value free to give back a boolean // success message. If total_bytes is too big, the FIFO will copy only what is available // into the USB buffer! -bool usbd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16_t total_bytes) -{ +bool usbd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t* ff, uint16_t total_bytes) { rhport = _usbd_rhport; uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); TU_LOG_USBD(" Queue ISO EP %02X with %u bytes ... ", ep_addr, total_bytes); @@ -1273,12 +1209,10 @@ bool usbd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16 // and usbd task can preempt and clear the busy _usbd_dev.ep_status[epnum][dir].busy = 1; - if (dcd_edpt_xfer_fifo(rhport, ep_addr, ff, total_bytes)) - { + if (dcd_edpt_xfer_fifo(rhport, ep_addr, ff, total_bytes)) { TU_LOG_USBD("OK\r\n"); return true; - }else - { + } else { // DCD error, mark endpoint as ready to allow next transfer _usbd_dev.ep_status[epnum][dir].busy = 0; _usbd_dev.ep_status[epnum][dir].claimed = 0; @@ -1288,26 +1222,23 @@ bool usbd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16 } } -bool usbd_edpt_busy(uint8_t rhport, uint8_t ep_addr) -{ +bool usbd_edpt_busy(uint8_t rhport, uint8_t ep_addr) { (void) rhport; uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); return _usbd_dev.ep_status[epnum][dir].busy; } -void usbd_edpt_stall(uint8_t rhport, uint8_t ep_addr) -{ +void usbd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { rhport = _usbd_rhport; uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); // only stalled if currently cleared - if ( !_usbd_dev.ep_status[epnum][dir].stalled ) - { + if (!_usbd_dev.ep_status[epnum][dir].stalled) { TU_LOG_USBD(" Stall EP %02X\r\n", ep_addr); dcd_edpt_stall(rhport, ep_addr); _usbd_dev.ep_status[epnum][dir].stalled = 1; @@ -1315,16 +1246,14 @@ void usbd_edpt_stall(uint8_t rhport, uint8_t ep_addr) } } -void usbd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) -{ +void usbd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { rhport = _usbd_rhport; uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); // only clear if currently stalled - if ( _usbd_dev.ep_status[epnum][dir].stalled ) - { + if (_usbd_dev.ep_status[epnum][dir].stalled) { TU_LOG_USBD(" Clear Stall EP %02X\r\n", ep_addr); dcd_edpt_clear_stall(rhport, ep_addr); _usbd_dev.ep_status[epnum][dir].stalled = 0; @@ -1332,31 +1261,27 @@ void usbd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) } } -bool usbd_edpt_stalled(uint8_t rhport, uint8_t ep_addr) -{ +bool usbd_edpt_stalled(uint8_t rhport, uint8_t ep_addr) { (void) rhport; uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); return _usbd_dev.ep_status[epnum][dir].stalled; } /** * usbd_edpt_close will disable an endpoint. - * * In progress transfers on this EP may be delivered after this call. - * */ -void usbd_edpt_close(uint8_t rhport, uint8_t ep_addr) -{ +void usbd_edpt_close(uint8_t rhport, uint8_t ep_addr) { rhport = _usbd_rhport; TU_ASSERT(dcd_edpt_close, /**/); TU_LOG_USBD(" CLOSING Endpoint: 0x%02X\r\n", ep_addr); uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); dcd_edpt_close(rhport, ep_addr); _usbd_dev.ep_status[epnum][dir].stalled = 0; @@ -1366,8 +1291,7 @@ void usbd_edpt_close(uint8_t rhport, uint8_t ep_addr) return; } -void usbd_sof_enable(uint8_t rhport, bool en) -{ +void usbd_sof_enable(uint8_t rhport, bool en) { rhport = _usbd_rhport; // TODO: Check needed if all drivers including the user sof_cb does not need an active SOF ISR any more. @@ -1375,8 +1299,7 @@ void usbd_sof_enable(uint8_t rhport, bool en) dcd_sof_enable(rhport, en); } -bool usbd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) -{ +bool usbd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { rhport = _usbd_rhport; TU_ASSERT(dcd_edpt_iso_alloc); @@ -1385,12 +1308,11 @@ bool usbd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packe return dcd_edpt_iso_alloc(rhport, ep_addr, largest_packet_size); } -bool usbd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const * desc_ep) -{ +bool usbd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const* desc_ep) { rhport = _usbd_rhport; uint8_t const epnum = tu_edpt_number(desc_ep->bEndpointAddress); - uint8_t const dir = tu_edpt_dir(desc_ep->bEndpointAddress); + uint8_t const dir = tu_edpt_dir(desc_ep->bEndpointAddress); TU_ASSERT(dcd_edpt_iso_activate); TU_ASSERT(epnum < CFG_TUD_ENDPPOINT_MAX); diff --git a/src/portable/raspberrypi/rp2040/dcd_rp2040.c b/src/portable/raspberrypi/rp2040/dcd_rp2040.c index e8cee73fd..ba7e9f912 100644 --- a/src/portable/raspberrypi/rp2040/dcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/dcd_rp2040.c @@ -48,7 +48,7 @@ *------------------------------------------------------------------*/ // Init these in dcd_init -static uint8_t *next_buffer_ptr; +static uint8_t* next_buffer_ptr; // USB_MAX_ENDPOINTS Endpoints, direction TUSB_DIR_OUT for out and TUSB_DIR_IN for in. static struct hw_endpoint hw_endpoints[USB_MAX_ENDPOINTS][2]; @@ -56,79 +56,70 @@ static struct hw_endpoint hw_endpoints[USB_MAX_ENDPOINTS][2]; // SOF may be used by remote wakeup as RESUME, this indicate whether SOF is actually used by usbd static bool _sof_enable = false; -TU_ATTR_ALWAYS_INLINE static inline struct hw_endpoint *hw_endpoint_get_by_num(uint8_t num, tusb_dir_t dir) -{ +TU_ATTR_ALWAYS_INLINE static inline struct hw_endpoint* hw_endpoint_get_by_num(uint8_t num, tusb_dir_t dir) { return &hw_endpoints[num][dir]; } -static struct hw_endpoint *hw_endpoint_get_by_addr(uint8_t ep_addr) -{ +static struct hw_endpoint* hw_endpoint_get_by_addr(uint8_t ep_addr) { uint8_t num = tu_edpt_number(ep_addr); tusb_dir_t dir = tu_edpt_dir(ep_addr); return hw_endpoint_get_by_num(num, dir); } -static void _hw_endpoint_alloc(struct hw_endpoint *ep, uint8_t transfer_type) -{ +static void _hw_endpoint_alloc(struct hw_endpoint* ep, uint8_t transfer_type) { // size must be multiple of 64 uint size = tu_div_ceil(ep->wMaxPacketSize, 64) * 64u; // double buffered Bulk endpoint - if ( transfer_type == TUSB_XFER_BULK ) - { + if (transfer_type == TUSB_XFER_BULK) { size *= 2u; } ep->hw_data_buf = next_buffer_ptr; next_buffer_ptr += size; - assert(((uintptr_t )next_buffer_ptr & 0b111111u) == 0); + assert(((uintptr_t) next_buffer_ptr & 0b111111u) == 0); uint dpram_offset = hw_data_offset(ep->hw_data_buf); hard_assert(hw_data_offset(next_buffer_ptr) <= USB_DPRAM_MAX); pico_info(" Allocated %d bytes at offset 0x%x (0x%p)\r\n", size, dpram_offset, ep->hw_data_buf); // Fill in endpoint control register with buffer offset - uint32_t const reg = EP_CTRL_ENABLE_BITS | ((uint)transfer_type << EP_CTRL_BUFFER_TYPE_LSB) | dpram_offset; + uint32_t const reg = EP_CTRL_ENABLE_BITS | ((uint) transfer_type << EP_CTRL_BUFFER_TYPE_LSB) | dpram_offset; *ep->endpoint_control = reg; } -static void _hw_endpoint_close(struct hw_endpoint *ep) -{ - // Clear hardware registers and then zero the struct - // Clears endpoint enable - *ep->endpoint_control = 0; - // Clears buffer available, etc - *ep->buffer_control = 0; - // Clear any endpoint state - memset(ep, 0, sizeof(struct hw_endpoint)); - - // Reclaim buffer space if all endpoints are closed - bool reclaim_buffers = true; - for ( uint8_t i = 1; i < USB_MAX_ENDPOINTS; i++ ) - { - if (hw_endpoint_get_by_num(i, TUSB_DIR_OUT)->hw_data_buf != NULL || hw_endpoint_get_by_num(i, TUSB_DIR_IN)->hw_data_buf != NULL) - { - reclaim_buffers = false; - break; - } - } - if (reclaim_buffers) - { - next_buffer_ptr = &usb_dpram->epx_data[0]; +static void _hw_endpoint_close(struct hw_endpoint* ep) { + // Clear hardware registers and then zero the struct + // Clears endpoint enable + *ep->endpoint_control = 0; + // Clears buffer available, etc + *ep->buffer_control = 0; + // Clear any endpoint state + memset(ep, 0, sizeof(struct hw_endpoint)); + + // Reclaim buffer space if all endpoints are closed + bool reclaim_buffers = true; + for (uint8_t i = 1; i < USB_MAX_ENDPOINTS; i++) { + if (hw_endpoint_get_by_num(i, TUSB_DIR_OUT)->hw_data_buf != NULL || + hw_endpoint_get_by_num(i, TUSB_DIR_IN)->hw_data_buf != NULL) { + reclaim_buffers = false; + break; } + } + if (reclaim_buffers) { + next_buffer_ptr = &usb_dpram->epx_data[0]; + } } -static void hw_endpoint_close(uint8_t ep_addr) -{ - struct hw_endpoint *ep = hw_endpoint_get_by_addr(ep_addr); - _hw_endpoint_close(ep); +static void hw_endpoint_close(uint8_t ep_addr) { + struct hw_endpoint* ep = hw_endpoint_get_by_addr(ep_addr); + _hw_endpoint_close(ep); } -static void hw_endpoint_init(uint8_t ep_addr, uint16_t wMaxPacketSize, uint8_t transfer_type) -{ - struct hw_endpoint *ep = hw_endpoint_get_by_addr(ep_addr); +static void hw_endpoint_init(uint8_t ep_addr, uint16_t wMaxPacketSize, uint8_t transfer_type) { + struct hw_endpoint* ep = hw_endpoint_get_by_addr(ep_addr); const uint8_t num = tu_edpt_number(ep_addr); const tusb_dir_t dir = tu_edpt_dir(ep_addr); @@ -143,35 +134,26 @@ static void hw_endpoint_init(uint8_t ep_addr, uint16_t wMaxPacketSize, uint8_t t ep->transfer_type = transfer_type; // Every endpoint has a buffer control register in dpram - if ( dir == TUSB_DIR_IN ) - { + if (dir == TUSB_DIR_IN) { ep->buffer_control = &usb_dpram->ep_buf_ctrl[num].in; - } - else - { + } else { ep->buffer_control = &usb_dpram->ep_buf_ctrl[num].out; } // Clear existing buffer control state *ep->buffer_control = 0; - if ( num == 0 ) - { + if (num == 0) { // EP0 has no endpoint control register because the buffer offsets are fixed ep->endpoint_control = NULL; // Buffer offset is fixed (also double buffered) ep->hw_data_buf = (uint8_t*) &usb_dpram->ep0_buf_a[0]; - } - else - { + } else { // Set the endpoint control register (starts at EP1, hence num-1) - if ( dir == TUSB_DIR_IN ) - { + if (dir == TUSB_DIR_IN) { ep->endpoint_control = &usb_dpram->ep_ctrl[num - 1].in; - } - else - { + } else { ep->endpoint_control = &usb_dpram->ep_ctrl[num - 1].out; } @@ -180,76 +162,65 @@ static void hw_endpoint_init(uint8_t ep_addr, uint16_t wMaxPacketSize, uint8_t t } } -static void hw_endpoint_xfer(uint8_t ep_addr, uint8_t *buffer, uint16_t total_bytes) -{ - struct hw_endpoint *ep = hw_endpoint_get_by_addr(ep_addr); - hw_endpoint_xfer_start(ep, buffer, total_bytes); +static void hw_endpoint_xfer(uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes) { + struct hw_endpoint* ep = hw_endpoint_get_by_addr(ep_addr); + hw_endpoint_xfer_start(ep, buffer, total_bytes); } -static void __tusb_irq_path_func(hw_handle_buff_status)(void) -{ - uint32_t remaining_buffers = usb_hw->buf_status; - pico_trace("buf_status = 0x%08lx\r\n", remaining_buffers); - uint bit = 1u; - for (uint8_t i = 0; remaining_buffers && i < USB_MAX_ENDPOINTS * 2; i++) - { - if (remaining_buffers & bit) - { - // clear this in advance - usb_hw_clear->buf_status = bit; - - // IN transfer for even i, OUT transfer for odd i - struct hw_endpoint *ep = hw_endpoint_get_by_num(i >> 1u, (i & 1u) ? TUSB_DIR_OUT : TUSB_DIR_IN); - - // Continue xfer - bool done = hw_endpoint_xfer_continue(ep); - if (done) - { - // Notify - dcd_event_xfer_complete(0, ep->ep_addr, ep->xferred_len, XFER_RESULT_SUCCESS, true); - hw_endpoint_reset_transfer(ep); - } - remaining_buffers &= ~bit; - } - bit <<= 1u; +static void __tusb_irq_path_func(hw_handle_buff_status)(void) { + uint32_t remaining_buffers = usb_hw->buf_status; + pico_trace("buf_status = 0x%08lx\r\n", remaining_buffers); + uint bit = 1u; + for (uint8_t i = 0; remaining_buffers && i < USB_MAX_ENDPOINTS * 2; i++) { + if (remaining_buffers & bit) { + // clear this in advance + usb_hw_clear->buf_status = bit; + + // IN transfer for even i, OUT transfer for odd i + struct hw_endpoint* ep = hw_endpoint_get_by_num(i >> 1u, (i & 1u) ? TUSB_DIR_OUT : TUSB_DIR_IN); + + // Continue xfer + bool done = hw_endpoint_xfer_continue(ep); + if (done) { + // Notify + dcd_event_xfer_complete(0, ep->ep_addr, ep->xferred_len, XFER_RESULT_SUCCESS, true); + hw_endpoint_reset_transfer(ep); + } + remaining_buffers &= ~bit; } + bit <<= 1u; + } } -TU_ATTR_ALWAYS_INLINE static inline void reset_ep0_pid(void) -{ - // If we have finished this transfer on EP0 set pid back to 1 for next - // setup transfer. Also clear a stall in case - uint8_t addrs[] = {0x0, 0x80}; - for (uint i = 0 ; i < TU_ARRAY_SIZE(addrs); i++) - { - struct hw_endpoint *ep = hw_endpoint_get_by_addr(addrs[i]); - ep->next_pid = 1u; - } +TU_ATTR_ALWAYS_INLINE static inline void reset_ep0_pid(void) { + // If we have finished this transfer on EP0 set pid back to 1 for next + // setup transfer. Also clear a stall in case + uint8_t addrs[] = {0x0, 0x80}; + for (uint i = 0; i < TU_ARRAY_SIZE(addrs); i++) { + struct hw_endpoint* ep = hw_endpoint_get_by_addr(addrs[i]); + ep->next_pid = 1u; + } } -static void __tusb_irq_path_func(reset_non_control_endpoints)(void) -{ +static void __tusb_irq_path_func(reset_non_control_endpoints)(void) { // Disable all non-control - for ( uint8_t i = 0; i < USB_MAX_ENDPOINTS-1; i++ ) - { + for (uint8_t i = 0; i < USB_MAX_ENDPOINTS - 1; i++) { usb_dpram->ep_ctrl[i].in = 0; usb_dpram->ep_ctrl[i].out = 0; } // clear non-control hw endpoints - tu_memclr(hw_endpoints[1], sizeof(hw_endpoints) - 2*sizeof(hw_endpoint_t)); + tu_memclr(hw_endpoints[1], sizeof(hw_endpoints) - 2 * sizeof(hw_endpoint_t)); // reclaim buffer space next_buffer_ptr = &usb_dpram->epx_data[0]; } -static void __tusb_irq_path_func(dcd_rp2040_irq)(void) -{ +static void __tusb_irq_path_func(dcd_rp2040_irq)(void) { uint32_t const status = usb_hw->ints; uint32_t handled = 0; - if ( status & USB_INTF_DEV_SOF_BITS ) - { + if (status & USB_INTF_DEV_SOF_BITS) { bool keep_sof_alive = false; handled |= USB_INTF_DEV_SOF_BITS; @@ -258,20 +229,17 @@ static void __tusb_irq_path_func(dcd_rp2040_irq)(void) // Errata 15 workaround for Device Bulk-In endpoint e15_last_sof = time_us_32(); - for ( uint8_t i = 0; i < USB_MAX_ENDPOINTS; i++ ) - { - struct hw_endpoint * ep = hw_endpoint_get_by_num(i, TUSB_DIR_IN); + for (uint8_t i = 0; i < USB_MAX_ENDPOINTS; i++) { + struct hw_endpoint* ep = hw_endpoint_get_by_num(i, TUSB_DIR_IN); // Active Bulk IN endpoint requires SOF - if ( (ep->transfer_type == TUSB_XFER_BULK) && ep->active ) - { + if ((ep->transfer_type == TUSB_XFER_BULK) && ep->active) { keep_sof_alive = true; hw_endpoint_lock_update(ep, 1); // Deferred enable? - if ( ep->pending ) - { + if (ep->pending) { ep->pending = 0; hw_endpoint_start_next_buffer(ep); } @@ -282,23 +250,21 @@ static void __tusb_irq_path_func(dcd_rp2040_irq)(void) #endif // disable SOF interrupt if it is used for RESUME in remote wakeup - if ( !keep_sof_alive && !_sof_enable ) usb_hw_clear->inte = USB_INTS_DEV_SOF_BITS; + if (!keep_sof_alive && !_sof_enable) usb_hw_clear->inte = USB_INTS_DEV_SOF_BITS; dcd_event_sof(0, usb_hw->sof_rd & USB_SOF_RD_BITS, true); } // xfer events are handled before setup req. So if a transfer completes immediately // before closing the EP, the events will be delivered in same order. - if ( status & USB_INTS_BUFF_STATUS_BITS ) - { + if (status & USB_INTS_BUFF_STATUS_BITS) { handled |= USB_INTS_BUFF_STATUS_BITS; hw_handle_buff_status(); } - if ( status & USB_INTS_SETUP_REQ_BITS ) - { + if (status & USB_INTS_SETUP_REQ_BITS) { handled |= USB_INTS_SETUP_REQ_BITS; - uint8_t const * setup = remove_volatile_cast(uint8_t const*, &usb_dpram->setup_packet); + uint8_t const* setup = remove_volatile_cast(uint8_t const*, &usb_dpram->setup_packet); // reset pid to both 1 (data and ack) reset_ep0_pid(); @@ -329,8 +295,7 @@ static void __tusb_irq_path_func(dcd_rp2040_irq)(void) #endif // SE0 for 2.5 us or more (will last at least 10ms) - if ( status & USB_INTS_BUS_RESET_BITS ) - { + if (status & USB_INTS_BUS_RESET_BITS) { pico_trace("BUS RESET\r\n"); handled |= USB_INTS_BUS_RESET_BITS; @@ -342,7 +307,7 @@ static void __tusb_irq_path_func(dcd_rp2040_irq)(void) #if TUD_OPT_RP2040_USB_DEVICE_ENUMERATION_FIX // Only run enumeration workaround if pull up is enabled - if ( usb_hw->sie_ctrl & USB_SIE_CTRL_PULLUP_EN_BITS ) rp2040_usb_device_enumeration_fix(); + if (usb_hw->sie_ctrl & USB_SIE_CTRL_PULLUP_EN_BITS) rp2040_usb_device_enumeration_fix(); #endif } @@ -354,22 +319,19 @@ static void __tusb_irq_path_func(dcd_rp2040_irq)(void) * because without VBUS detection, it is impossible to tell the difference between * being disconnected and suspended. */ - if ( status & USB_INTS_DEV_SUSPEND_BITS ) - { + if (status & USB_INTS_DEV_SUSPEND_BITS) { handled |= USB_INTS_DEV_SUSPEND_BITS; dcd_event_bus_signal(0, DCD_EVENT_SUSPEND, true); usb_hw_clear->sie_status = USB_SIE_STATUS_SUSPENDED_BITS; } - if ( status & USB_INTS_DEV_RESUME_FROM_HOST_BITS ) - { + if (status & USB_INTS_DEV_RESUME_FROM_HOST_BITS) { handled |= USB_INTS_DEV_RESUME_FROM_HOST_BITS; dcd_event_bus_signal(0, DCD_EVENT_RESUME, true); usb_hw_clear->sie_status = USB_SIE_STATUS_RESUME_BITS; } - if ( status ^ handled ) - { + if (status ^ handled) { panic("Unhandled IRQ 0x%x\n", (uint) (status ^ handled)); } } @@ -390,8 +352,7 @@ static void __tusb_irq_path_func(dcd_rp2040_irq)(void) #define PICO_SHARED_IRQ_HANDLER_HIGHEST_ORDER_PRIORITY 0xff #endif -void dcd_init (uint8_t rhport) -{ +void dcd_init(uint8_t rhport) { assert(rhport == 0); // Reset hardware to default state @@ -405,7 +366,7 @@ void dcd_init (uint8_t rhport) irq_add_shared_handler(USBCTRL_IRQ, dcd_rp2040_irq, PICO_SHARED_IRQ_HANDLER_HIGHEST_ORDER_PRIORITY); // Init control endpoints - tu_memclr(hw_endpoints[0], 2*sizeof(hw_endpoint_t)); + tu_memclr(hw_endpoints[0], 2 * sizeof(hw_endpoint_t)); hw_endpoint_init(0x0, 64, TUSB_XFER_CONTROL); hw_endpoint_init(0x80, 64, TUSB_XFER_CONTROL); @@ -420,27 +381,24 @@ void dcd_init (uint8_t rhport) // for the global interrupt enable... // Note: Force VBUS detect cause disconnection not detectable usb_hw->sie_ctrl = USB_SIE_CTRL_EP0_INT_1BUF_BITS; - usb_hw->inte = USB_INTS_BUFF_STATUS_BITS | USB_INTS_BUS_RESET_BITS | USB_INTS_SETUP_REQ_BITS | - USB_INTS_DEV_SUSPEND_BITS | USB_INTS_DEV_RESUME_FROM_HOST_BITS | - (FORCE_VBUS_DETECT ? 0 : USB_INTS_DEV_CONN_DIS_BITS); + usb_hw->inte = USB_INTS_BUFF_STATUS_BITS | USB_INTS_BUS_RESET_BITS | USB_INTS_SETUP_REQ_BITS | + USB_INTS_DEV_SUSPEND_BITS | USB_INTS_DEV_RESUME_FROM_HOST_BITS | + (FORCE_VBUS_DETECT ? 0 : USB_INTS_DEV_CONN_DIS_BITS); dcd_connect(rhport); } -void dcd_int_enable(__unused uint8_t rhport) -{ - assert(rhport == 0); - irq_set_enabled(USBCTRL_IRQ, true); +void dcd_int_enable(__unused uint8_t rhport) { + assert(rhport == 0); + irq_set_enabled(USBCTRL_IRQ, true); } -void dcd_int_disable(__unused uint8_t rhport) -{ - assert(rhport == 0); - irq_set_enabled(USBCTRL_IRQ, false); +void dcd_int_disable(__unused uint8_t rhport) { + assert(rhport == 0); + irq_set_enabled(USBCTRL_IRQ, false); } -void dcd_set_address (__unused uint8_t rhport, __unused uint8_t dev_addr) -{ +void dcd_set_address(__unused uint8_t rhport, __unused uint8_t dev_addr) { assert(rhport == 0); // Can't set device address in hardware until status xfer has complete @@ -448,8 +406,7 @@ void dcd_set_address (__unused uint8_t rhport, __unused uint8_t dev_addr) hw_endpoint_xfer(0x80, NULL, 0); } -void dcd_remote_wakeup(__unused uint8_t rhport) -{ +void dcd_remote_wakeup(__unused uint8_t rhport) { pico_info("dcd_remote_wakeup %d\n", rhport); assert(rhport == 0); @@ -460,100 +417,88 @@ void dcd_remote_wakeup(__unused uint8_t rhport) } // disconnect by disabling internal pull-up resistor on D+/D- -void dcd_disconnect(__unused uint8_t rhport) -{ +void dcd_disconnect(__unused uint8_t rhport) { (void) rhport; usb_hw_clear->sie_ctrl = USB_SIE_CTRL_PULLUP_EN_BITS; } // connect by enabling internal pull-up resistor on D+/D- -void dcd_connect(__unused uint8_t rhport) -{ +void dcd_connect(__unused uint8_t rhport) { (void) rhport; usb_hw_set->sie_ctrl = USB_SIE_CTRL_PULLUP_EN_BITS; } -void dcd_sof_enable(uint8_t rhport, bool en) -{ +void dcd_sof_enable(uint8_t rhport, bool en) { (void) rhport; _sof_enable = en; - if (en) - { + if (en) { usb_hw_set->inte = USB_INTS_DEV_SOF_BITS; - }else - { + } +#if !TUD_OPT_RP2040_USB_DEVICE_UFRAME_FIX + else { // Don't clear immediately if the SOF workaround is in use. // The SOF handler will conditionally disable the interrupt. -#if !TUD_OPT_RP2040_USB_DEVICE_UFRAME_FIX usb_hw_clear->inte = USB_INTS_DEV_SOF_BITS; -#endif } +#endif } /*------------------------------------------------------------------*/ /* DCD Endpoint port *------------------------------------------------------------------*/ -void dcd_edpt0_status_complete(uint8_t rhport, tusb_control_request_t const * request) -{ +void dcd_edpt0_status_complete(uint8_t rhport, tusb_control_request_t const* request) { (void) rhport; - if ( request->bmRequestType_bit.recipient == TUSB_REQ_RCPT_DEVICE && - request->bmRequestType_bit.type == TUSB_REQ_TYPE_STANDARD && - request->bRequest == TUSB_REQ_SET_ADDRESS ) - { + if (request->bmRequestType_bit.recipient == TUSB_REQ_RCPT_DEVICE && + request->bmRequestType_bit.type == TUSB_REQ_TYPE_STANDARD && + request->bRequest == TUSB_REQ_SET_ADDRESS) { usb_hw->dev_addr_ctrl = (uint8_t) request->wValue; } } -bool dcd_edpt_open (__unused uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) -{ - assert(rhport == 0); - hw_endpoint_init(desc_edpt->bEndpointAddress, tu_edpt_packet_size(desc_edpt), desc_edpt->bmAttributes.xfer); - return true; +bool dcd_edpt_open(__unused uint8_t rhport, tusb_desc_endpoint_t const* desc_edpt) { + assert(rhport == 0); + hw_endpoint_init(desc_edpt->bEndpointAddress, tu_edpt_packet_size(desc_edpt), desc_edpt->bmAttributes.xfer); + return true; } -void dcd_edpt_close_all (uint8_t rhport) -{ +void dcd_edpt_close_all(uint8_t rhport) { (void) rhport; // may need to use EP Abort reset_non_control_endpoints(); } -bool dcd_edpt_xfer(__unused uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t total_bytes) -{ - assert(rhport == 0); - hw_endpoint_xfer(ep_addr, buffer, total_bytes); - return true; +bool dcd_edpt_xfer(__unused uint8_t rhport, uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes) { + assert(rhport == 0); + hw_endpoint_xfer(ep_addr, buffer, total_bytes); + return true; } -void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) -{ +void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { (void) rhport; - if ( tu_edpt_number(ep_addr) == 0 ) - { + if (tu_edpt_number(ep_addr) == 0) { // A stall on EP0 has to be armed so it can be cleared on the next setup packet - usb_hw_set->ep_stall_arm = (tu_edpt_dir(ep_addr) == TUSB_DIR_IN) ? USB_EP_STALL_ARM_EP0_IN_BITS : USB_EP_STALL_ARM_EP0_OUT_BITS; + usb_hw_set->ep_stall_arm = (tu_edpt_dir(ep_addr) == TUSB_DIR_IN) ? USB_EP_STALL_ARM_EP0_IN_BITS + : USB_EP_STALL_ARM_EP0_OUT_BITS; } - struct hw_endpoint *ep = hw_endpoint_get_by_addr(ep_addr); + struct hw_endpoint* ep = hw_endpoint_get_by_addr(ep_addr); // stall and clear current pending buffer // may need to use EP_ABORT _hw_endpoint_buffer_control_set_value32(ep, USB_BUF_CTRL_STALL); } -void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) -{ +void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { (void) rhport; - if (tu_edpt_number(ep_addr)) - { - struct hw_endpoint *ep = hw_endpoint_get_by_addr(ep_addr); + if (tu_edpt_number(ep_addr)) { + struct hw_endpoint* ep = hw_endpoint_get_by_addr(ep_addr); // clear stall also reset toggle to DATA0, ready for next transfer ep->next_pid = 0; @@ -561,16 +506,13 @@ void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) } } -void dcd_edpt_close (uint8_t rhport, uint8_t ep_addr) -{ - (void) rhport; - - pico_trace("dcd_edpt_close %02x\r\n", ep_addr); - hw_endpoint_close(ep_addr); +void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) { + (void) rhport; + pico_trace("dcd_edpt_close %02x\r\n", ep_addr); + hw_endpoint_close(ep_addr); } -void __tusb_irq_path_func(dcd_int_handler)(uint8_t rhport) -{ +void __tusb_irq_path_func(dcd_int_handler)(uint8_t rhport) { (void) rhport; dcd_rp2040_irq(); } diff --git a/src/portable/raspberrypi/rp2040/rp2040_usb.c b/src/portable/raspberrypi/rp2040/rp2040_usb.c index a512dc34f..b5bace972 100644 --- a/src/portable/raspberrypi/rp2040/rp2040_usb.c +++ b/src/portable/raspberrypi/rp2040/rp2040_usb.c @@ -37,24 +37,23 @@ //--------------------------------------------------------------------+ // Direction strings for debug -const char *ep_dir_string[] = { - "out", - "in", +const char* ep_dir_string[] = { + "out", + "in", }; -static void _hw_endpoint_xfer_sync(struct hw_endpoint *ep); +static void _hw_endpoint_xfer_sync(struct hw_endpoint* ep); #if TUD_OPT_RP2040_USB_DEVICE_UFRAME_FIX - static bool e15_is_bulkin_ep(struct hw_endpoint *ep); - static bool e15_is_critical_frame_period(struct hw_endpoint *ep); + static bool e15_is_bulkin_ep(struct hw_endpoint* ep); + static bool e15_is_critical_frame_period(struct hw_endpoint* ep); #else #define e15_is_bulkin_ep(x) (false) #define e15_is_critical_frame_period(x) (false) #endif // if usb hardware is in host mode -TU_ATTR_ALWAYS_INLINE static inline bool is_host_mode(void) -{ +TU_ATTR_ALWAYS_INLINE static inline bool is_host_mode(void) { return (usb_hw->main_ctrl & USB_MAIN_CTRL_HOST_NDEVICE_BITS) ? true : false; } @@ -62,8 +61,7 @@ TU_ATTR_ALWAYS_INLINE static inline bool is_host_mode(void) // Implementation //--------------------------------------------------------------------+ -void rp2040_usb_init(void) -{ +void rp2040_usb_init(void) { // Reset usb controller reset_block(RESETS_RESET_USBCTRL_BITS); unreset_block_wait(RESETS_RESET_USBCTRL_BITS); @@ -88,45 +86,40 @@ void rp2040_usb_init(void) TU_LOG2_INT(sizeof(hw_endpoint_t)); } -void __tusb_irq_path_func(hw_endpoint_reset_transfer)(struct hw_endpoint *ep) -{ +void __tusb_irq_path_func(hw_endpoint_reset_transfer)(struct hw_endpoint* ep) { ep->active = false; ep->remaining_len = 0; ep->xferred_len = 0; ep->user_buf = 0; } -void __tusb_irq_path_func(_hw_endpoint_buffer_control_update32)(struct hw_endpoint *ep, uint32_t and_mask, uint32_t or_mask) -{ +void __tusb_irq_path_func(_hw_endpoint_buffer_control_update32)(struct hw_endpoint* ep, uint32_t and_mask, + uint32_t or_mask) { uint32_t value = 0; - if ( and_mask ) - { + if (and_mask) { value = *ep->buffer_control & and_mask; } - if ( or_mask ) - { + if (or_mask) { value |= or_mask; - if ( or_mask & USB_BUF_CTRL_AVAIL ) - { - if ( *ep->buffer_control & USB_BUF_CTRL_AVAIL ) - { + if (or_mask & USB_BUF_CTRL_AVAIL) { + if (*ep->buffer_control & USB_BUF_CTRL_AVAIL) { panic("ep %d %s was already available", tu_edpt_number(ep->ep_addr), ep_dir_string[tu_edpt_dir(ep->ep_addr)]); } *ep->buffer_control = value & ~USB_BUF_CTRL_AVAIL; // 12 cycle delay.. (should be good for 48*12Mhz = 576Mhz) // Don't need delay in host mode as host is in charge #if !CFG_TUH_ENABLED - __asm volatile ( - "b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1:\n" - : : : "memory"); + __asm volatile ( + "b 1f\n" + "1: b 1f\n" + "1: b 1f\n" + "1: b 1f\n" + "1: b 1f\n" + "1: b 1f\n" + "1:\n" + : : : "memory"); #endif } } @@ -135,10 +128,9 @@ void __tusb_irq_path_func(_hw_endpoint_buffer_control_update32)(struct hw_endpoi } // prepare buffer, return buffer control -static uint32_t __tusb_irq_path_func(prepare_ep_buffer)(struct hw_endpoint *ep, uint8_t buf_id) -{ +static uint32_t __tusb_irq_path_func(prepare_ep_buffer)(struct hw_endpoint* ep, uint8_t buf_id) { uint16_t const buflen = tu_min16(ep->remaining_len, ep->wMaxPacketSize); - ep->remaining_len = (uint16_t)(ep->remaining_len - buflen); + ep->remaining_len = (uint16_t) (ep->remaining_len - buflen); uint32_t buf_ctrl = buflen | USB_BUF_CTRL_AVAIL; @@ -146,10 +138,9 @@ static uint32_t __tusb_irq_path_func(prepare_ep_buffer)(struct hw_endpoint *ep, buf_ctrl |= ep->next_pid ? USB_BUF_CTRL_DATA1_PID : USB_BUF_CTRL_DATA0_PID; ep->next_pid ^= 1u; - if ( !ep->rx ) - { + if (!ep->rx) { // Copy data from user buffer to hw buffer - memcpy(ep->hw_data_buf + buf_id*64, ep->user_buf, buflen); + memcpy(ep->hw_data_buf + buf_id * 64, ep->user_buf, buflen); ep->user_buf += buflen; // Mark as full @@ -159,8 +150,7 @@ static uint32_t __tusb_irq_path_func(prepare_ep_buffer)(struct hw_endpoint *ep, // Is this the last buffer? Only really matters for host mode. Will trigger // the trans complete irq but also stop it polling. We only really care about // trans complete for setup packets being sent - if (ep->remaining_len == 0) - { + if (ep->remaining_len == 0) { buf_ctrl |= USB_BUF_CTRL_LAST; } @@ -170,8 +160,7 @@ static uint32_t __tusb_irq_path_func(prepare_ep_buffer)(struct hw_endpoint *ep, } // Prepare buffer control register value -void __tusb_irq_path_func(hw_endpoint_start_next_buffer)(struct hw_endpoint *ep) -{ +void __tusb_irq_path_func(hw_endpoint_start_next_buffer)(struct hw_endpoint* ep) { uint32_t ep_ctrl = *ep->endpoint_control; // always compute and start with buffer 0 @@ -186,8 +175,7 @@ void __tusb_irq_path_func(hw_endpoint_start_next_buffer)(struct hw_endpoint *ep) bool const force_single = (!is_host && !tu_edpt_dir(ep->ep_addr)) || (is_host && tu_edpt_number(ep->ep_addr) != 0); - if(ep->remaining_len && !force_single) - { + if (ep->remaining_len && !force_single) { // Use buffer 1 (double buffered) if there is still data // TODO: Isochronous for buffer1 bit-field is different than CBI (control bulk, interrupt) @@ -196,8 +184,7 @@ void __tusb_irq_path_func(hw_endpoint_start_next_buffer)(struct hw_endpoint *ep) // Set endpoint control double buffered bit if needed ep_ctrl &= ~EP_CTRL_INTERRUPT_PER_BUFFER; ep_ctrl |= EP_CTRL_DOUBLE_BUFFERED_BITS | EP_CTRL_INTERRUPT_PER_DOUBLE_BUFFER; - }else - { + } else { // Single buffered since 1 is enough ep_ctrl &= ~(EP_CTRL_DOUBLE_BUFFERED_BITS | EP_CTRL_INTERRUPT_PER_DOUBLE_BUFFER); ep_ctrl |= EP_CTRL_INTERRUPT_PER_BUFFER; @@ -212,35 +199,30 @@ void __tusb_irq_path_func(hw_endpoint_start_next_buffer)(struct hw_endpoint *ep) _hw_endpoint_buffer_control_set_value32(ep, buf_ctrl); } -void hw_endpoint_xfer_start(struct hw_endpoint *ep, uint8_t *buffer, uint16_t total_len) -{ +void hw_endpoint_xfer_start(struct hw_endpoint* ep, uint8_t* buffer, uint16_t total_len) { hw_endpoint_lock_update(ep, 1); - if ( ep->active ) - { + if (ep->active) { // TODO: Is this acceptable for interrupt packets? TU_LOG(1, "WARN: starting new transfer on already active ep %d %s\r\n", tu_edpt_number(ep->ep_addr), - ep_dir_string[tu_edpt_dir(ep->ep_addr)]); + ep_dir_string[tu_edpt_dir(ep->ep_addr)]); hw_endpoint_reset_transfer(ep); } // Fill in info now that we're kicking off the hw ep->remaining_len = total_len; - ep->xferred_len = 0; - ep->active = true; - ep->user_buf = buffer; + ep->xferred_len = 0; + ep->active = true; + ep->user_buf = buffer; - if ( e15_is_bulkin_ep(ep) ) - { + if (e15_is_bulkin_ep(ep)) { usb_hw_set->inte = USB_INTS_DEV_SOF_BITS; } - if ( e15_is_critical_frame_period(ep) ) - { + if (e15_is_critical_frame_period(ep)) { ep->pending = 1; - } else - { + } else { hw_endpoint_start_next_buffer(ep); } @@ -248,34 +230,30 @@ void hw_endpoint_xfer_start(struct hw_endpoint *ep, uint8_t *buffer, uint16_t to } // sync endpoint buffer and return transferred bytes -static uint16_t __tusb_irq_path_func(sync_ep_buffer)(struct hw_endpoint *ep, uint8_t buf_id) -{ +static uint16_t __tusb_irq_path_func(sync_ep_buffer)(struct hw_endpoint* ep, uint8_t buf_id) { uint32_t buf_ctrl = _hw_endpoint_buffer_control_get_value32(ep); - if (buf_id) buf_ctrl = buf_ctrl >> 16; + if (buf_id) buf_ctrl = buf_ctrl >> 16; uint16_t xferred_bytes = buf_ctrl & USB_BUF_CTRL_LEN_MASK; - if ( !ep->rx ) - { + if (!ep->rx) { // We are continuing a transfer here. If we are TX, we have successfully // sent some data can increase the length we have sent assert(!(buf_ctrl & USB_BUF_CTRL_FULL)); - ep->xferred_len = (uint16_t)(ep->xferred_len + xferred_bytes); - }else - { + ep->xferred_len = (uint16_t) (ep->xferred_len + xferred_bytes); + } else { // If we have received some data, so can increase the length // we have received AFTER we have copied it to the user buffer at the appropriate offset assert(buf_ctrl & USB_BUF_CTRL_FULL); - memcpy(ep->user_buf, ep->hw_data_buf + buf_id*64, xferred_bytes); - ep->xferred_len = (uint16_t)(ep->xferred_len + xferred_bytes); + memcpy(ep->user_buf, ep->hw_data_buf + buf_id * 64, xferred_bytes); + ep->xferred_len = (uint16_t) (ep->xferred_len + xferred_bytes); ep->user_buf += xferred_bytes; } // Short packet - if (xferred_bytes < ep->wMaxPacketSize) - { + if (xferred_bytes < ep->wMaxPacketSize) { pico_trace(" Short packet on buffer %d with %u bytes\r\n", buf_id, xferred_bytes); // Reduce total length as this is last packet ep->remaining_len = 0; @@ -284,8 +262,7 @@ static uint16_t __tusb_irq_path_func(sync_ep_buffer)(struct hw_endpoint *ep, uin return xferred_bytes; } -static void __tusb_irq_path_func(_hw_endpoint_xfer_sync) (struct hw_endpoint *ep) -{ +static void __tusb_irq_path_func(_hw_endpoint_xfer_sync)(struct hw_endpoint* ep) { // Update hw endpoint struct with info from hardware // after a buff status interrupt @@ -296,14 +273,11 @@ static void __tusb_irq_path_func(_hw_endpoint_xfer_sync) (struct hw_endpoint *ep uint16_t buf0_bytes = sync_ep_buffer(ep, 0); // sync buffer 1 if double buffered - if ( (*ep->endpoint_control) & EP_CTRL_DOUBLE_BUFFERED_BITS ) - { - if (buf0_bytes == ep->wMaxPacketSize) - { + if ((*ep->endpoint_control) & EP_CTRL_DOUBLE_BUFFERED_BITS) { + if (buf0_bytes == ep->wMaxPacketSize) { // sync buffer 1 if not short packet sync_ep_buffer(ep, 1); - }else - { + } else { // short packet on buffer 0 // TODO couldn't figure out how to handle this case which happen with net_lwip_webserver example // At this time (currently trigger per 2 buffer), the buffer1 is probably filled with data from @@ -335,14 +309,13 @@ static void __tusb_irq_path_func(_hw_endpoint_xfer_sync) (struct hw_endpoint *ep } // Returns true if transfer is complete -bool __tusb_irq_path_func(hw_endpoint_xfer_continue)(struct hw_endpoint *ep) -{ +bool __tusb_irq_path_func(hw_endpoint_xfer_continue)(struct hw_endpoint* ep) { hw_endpoint_lock_update(ep, 1); // Part way through a transfer - if (!ep->active) - { - panic("Can't continue xfer on inactive ep %d %s", tu_edpt_number(ep->ep_addr), ep_dir_string[tu_edpt_dir(ep->ep_addr)]); + if (!ep->active) { + panic("Can't continue xfer on inactive ep %d %s", tu_edpt_number(ep->ep_addr), + ep_dir_string[tu_edpt_dir(ep->ep_addr)]); } // Update EP struct from hardware state @@ -350,21 +323,16 @@ bool __tusb_irq_path_func(hw_endpoint_xfer_continue)(struct hw_endpoint *ep) // Now we have synced our state with the hardware. Is there more data to transfer? // If we are done then notify tinyusb - if (ep->remaining_len == 0) - { + if (ep->remaining_len == 0) { pico_trace("Completed transfer of %d bytes on ep %d %s\r\n", ep->xferred_len, tu_edpt_number(ep->ep_addr), ep_dir_string[tu_edpt_dir(ep->ep_addr)]); // Notify caller we are done so it can notify the tinyusb stack hw_endpoint_lock_update(ep, -1); return true; - } - else - { - if ( e15_is_critical_frame_period(ep) ) - { + } else { + if (e15_is_critical_frame_period(ep)) { ep->pending = 1; - } else - { + } else { hw_endpoint_start_next_buffer(ep); } } @@ -399,16 +367,14 @@ bool __tusb_irq_path_func(hw_endpoint_xfer_continue)(struct hw_endpoint *ep) volatile uint32_t e15_last_sof = 0; // check if Errata 15 is needed for this endpoint i.e device bulk-in -static bool __tusb_irq_path_func(e15_is_bulkin_ep) (struct hw_endpoint *ep) -{ +static bool __tusb_irq_path_func(e15_is_bulkin_ep)(struct hw_endpoint* ep) { return (!is_host_mode() && tu_edpt_dir(ep->ep_addr) == TUSB_DIR_IN && ep->transfer_type == TUSB_XFER_BULK); } // check if we need to apply Errata 15 workaround : i.e // Endpoint is BULK IN and is currently in critical frame period i.e 20% of last usb frame -static bool __tusb_irq_path_func(e15_is_critical_frame_period) (struct hw_endpoint *ep) -{ +static bool __tusb_irq_path_func(e15_is_critical_frame_period)(struct hw_endpoint* ep) { TU_VERIFY(e15_is_bulkin_ep(ep)); /* Avoid the last 200us (uframe 6.5-7) of a frame, up to the EOF2 point. @@ -419,11 +385,10 @@ static bool __tusb_irq_path_func(e15_is_critical_frame_period) (struct hw_endpoi if (delta < 800 || delta > 998) { return false; } - TU_LOG(3, "Avoiding sof %lu now %lu last %lu\r\n", (usb_hw->sof_rd + 1) & USB_SOF_RD_BITS, time_us_32(), e15_last_sof); + TU_LOG(3, "Avoiding sof %lu now %lu last %lu\r\n", (usb_hw->sof_rd + 1) & USB_SOF_RD_BITS, time_us_32(), + e15_last_sof); return true; } -#endif - - +#endif // TUD_OPT_RP2040_USB_DEVICE_UFRAME_FIX #endif -- cgit v1.3.1 From 6dc714b6de8eaa58e4239f831786d383b7f9bb86 Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 13 Mar 2024 11:41:58 +0700 Subject: - only abort ep0 if it is active - rename reset_ep0_pid() to reset_ep0() - minor update log message --- src/portable/raspberrypi/rp2040/dcd_rp2040.c | 70 +++++++++++----------------- src/portable/raspberrypi/rp2040/rp2040_usb.c | 35 ++++---------- 2 files changed, 36 insertions(+), 69 deletions(-) (limited to 'src/portable') diff --git a/src/portable/raspberrypi/rp2040/dcd_rp2040.c b/src/portable/raspberrypi/rp2040/dcd_rp2040.c index 0e9dd84e5..5c564cb1c 100644 --- a/src/portable/raspberrypi/rp2040/dcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/dcd_rp2040.c @@ -60,7 +60,7 @@ TU_ATTR_ALWAYS_INLINE static inline struct hw_endpoint* hw_endpoint_get_by_num(u return &hw_endpoints[num][dir]; } -static struct hw_endpoint* hw_endpoint_get_by_addr(uint8_t ep_addr) { +TU_ATTR_ALWAYS_INLINE static inline struct hw_endpoint* hw_endpoint_get_by_addr(uint8_t ep_addr) { uint8_t num = tu_edpt_number(ep_addr); tusb_dir_t dir = tu_edpt_dir(ep_addr); return hw_endpoint_get_by_num(num, dir); @@ -192,47 +192,31 @@ static void __tusb_irq_path_func(hw_handle_buff_status)(void) { } } -TU_ATTR_ALWAYS_INLINE static inline void reset_ep0_pid(void) -{ - // Abort any transactions from a prior control transfer, because - // receiving SETUP doesn't reset buffer control state. This works around - // a possible USB hardware erratum. - - // With this workaround a race window still exists, but smaller. - // ABORT flag is unusable prior to hardware B2 (RP2040-E2), so a larger - // race window exists for B1 and earlier. - if (rp2040_chip_version() >= 2) { - usb_hw_set->abort = 0x3; - while ((usb_hw->abort_done & 0x3) != 0x3) - ; - } - // If we have finished this transfer on EP0 set pid back to 1 for next - // setup transfer. Also clear a stall in case - uint8_t addrs[] = {0x0, 0x80}; - for (uint i = 0 ; i < TU_ARRAY_SIZE(addrs); i++) - { - struct hw_endpoint *ep = hw_endpoint_get_by_addr(addrs[i]); - ep->next_pid = 1u; - // Reset the buffer control now to minimize race conditions - _hw_endpoint_buffer_control_set_value32(ep, USB_BUF_CTRL_DATA1_PID | USB_BUF_CTRL_SEL); - // Explicit delay, because the one in - // _hw_endpoint_buffer_control_set_value32 is only to set AVAILABLE - __asm volatile ( - "b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1:\n" - : : : "memory"); - // Make sure local ep state matches peripheral - hw_endpoint_reset_transfer(ep); - } - if (rp2040_chip_version() >= 2) { - usb_hw_clear->abort = 0x3; - usb_hw_clear->abort_done = 0x3; +TU_ATTR_ALWAYS_INLINE static inline void reset_ep0(void) { + // If we have finished this transfer on EP0 set pid back to 1 for next + // setup transfer. Also clear a stall in case + for (uint8_t dir = 0; dir < 2; dir++) { + struct hw_endpoint* ep = hw_endpoint_get_by_num(0, dir); + if (ep->active) { + // Abort any pending transfer from a prior control transfer per USB specs + // Due to Errata RP2040-E2: ABORT flag is only applicable for B2 and later (unusable for B0, B1). + // Which means we are not guaranteed to safely abort pending transfer on B0 and B1. + uint32_t const abort_mask = (dir ? USB_EP_ABORT_EP0_IN_BITS : USB_EP_ABORT_EP0_OUT_BITS); + if (rp2040_chip_version() >= 2) { + usb_hw_set->abort = abort_mask; + while ((usb_hw->abort_done & abort_mask) != abort_mask) {} + } + + _hw_endpoint_buffer_control_set_value32(ep, USB_BUF_CTRL_DATA1_PID | USB_BUF_CTRL_SEL); + hw_endpoint_reset_transfer(ep); + + if (rp2040_chip_version() >= 2) { + usb_hw_clear->abort_done = abort_mask; + usb_hw_clear->abort = abort_mask; + } } + ep->next_pid = 1u; + } } static void __tusb_irq_path_func(reset_non_control_endpoints)(void) { @@ -300,7 +284,7 @@ static void __tusb_irq_path_func(dcd_rp2040_irq)(void) { uint8_t const* setup = remove_volatile_cast(uint8_t const*, &usb_dpram->setup_packet); // reset pid to both 1 (data and ack) - reset_ep0_pid(); + reset_ep0(); // Pass setup packet to tiny usb dcd_event_setup_received(0, setup, true); @@ -388,6 +372,8 @@ static void __tusb_irq_path_func(dcd_rp2040_irq)(void) { void dcd_init(uint8_t rhport) { assert(rhport == 0); + TU_LOG(2, "Chip Version B%u\r\n", rp2040_chip_version()); + // Reset hardware to default state rp2040_usb_init(); diff --git a/src/portable/raspberrypi/rp2040/rp2040_usb.c b/src/portable/raspberrypi/rp2040/rp2040_usb.c index b5bace972..1ca711c77 100644 --- a/src/portable/raspberrypi/rp2040/rp2040_usb.c +++ b/src/portable/raspberrypi/rp2040/rp2040_usb.c @@ -35,13 +35,6 @@ //--------------------------------------------------------------------+ // MACRO CONSTANT TYPEDEF PROTOTYPE //--------------------------------------------------------------------+ - -// Direction strings for debug -const char* ep_dir_string[] = { - "out", - "in", -}; - static void _hw_endpoint_xfer_sync(struct hw_endpoint* ep); #if TUD_OPT_RP2040_USB_DEVICE_UFRAME_FIX @@ -105,22 +98,14 @@ void __tusb_irq_path_func(_hw_endpoint_buffer_control_update32)(struct hw_endpoi value |= or_mask; if (or_mask & USB_BUF_CTRL_AVAIL) { if (*ep->buffer_control & USB_BUF_CTRL_AVAIL) { - panic("ep %d %s was already available", tu_edpt_number(ep->ep_addr), ep_dir_string[tu_edpt_dir(ep->ep_addr)]); + panic("ep %02X was already available", ep->ep_addr); } *ep->buffer_control = value & ~USB_BUF_CTRL_AVAIL; - // 12 cycle delay.. (should be good for 48*12Mhz = 576Mhz) + // 4.1.2.5.1 Con-current access: 12 cycles (should be good for 48*12Mhz = 576Mhz) after write to buffer control // Don't need delay in host mode as host is in charge -#if !CFG_TUH_ENABLED - __asm volatile ( - "b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1: b 1f\n" - "1:\n" - : : : "memory"); -#endif + if ( !is_host_mode()) { + busy_wait_at_least_cycles(12); + } } } @@ -204,9 +189,7 @@ void hw_endpoint_xfer_start(struct hw_endpoint* ep, uint8_t* buffer, uint16_t to if (ep->active) { // TODO: Is this acceptable for interrupt packets? - TU_LOG(1, "WARN: starting new transfer on already active ep %d %s\r\n", tu_edpt_number(ep->ep_addr), - ep_dir_string[tu_edpt_dir(ep->ep_addr)]); - + TU_LOG(1, "WARN: starting new transfer on already active ep %02X\r\n", ep->ep_addr); hw_endpoint_reset_transfer(ep); } @@ -314,8 +297,7 @@ bool __tusb_irq_path_func(hw_endpoint_xfer_continue)(struct hw_endpoint* ep) { // Part way through a transfer if (!ep->active) { - panic("Can't continue xfer on inactive ep %d %s", tu_edpt_number(ep->ep_addr), - ep_dir_string[tu_edpt_dir(ep->ep_addr)]); + panic("Can't continue xfer on inactive ep %02X", ep->ep_addr); } // Update EP struct from hardware state @@ -324,8 +306,7 @@ bool __tusb_irq_path_func(hw_endpoint_xfer_continue)(struct hw_endpoint* ep) { // Now we have synced our state with the hardware. Is there more data to transfer? // If we are done then notify tinyusb if (ep->remaining_len == 0) { - pico_trace("Completed transfer of %d bytes on ep %d %s\r\n", - ep->xferred_len, tu_edpt_number(ep->ep_addr), ep_dir_string[tu_edpt_dir(ep->ep_addr)]); + pico_trace("Completed transfer of %d bytes on ep %02X\r\n", ep->xferred_len, ep->ep_addr); // Notify caller we are done so it can notify the tinyusb stack hw_endpoint_lock_update(ep, -1); return true; -- cgit v1.3.1 From 5a854ef2dc03373f125b48e93accf302c2fbdd66 Mon Sep 17 00:00:00 2001 From: henneboi Date: Mon, 11 Mar 2024 13:36:25 +0100 Subject: dcd_stm32_fsdev.c: Fix a bug seend with stm32h5xxx when the driver is compiled with cubeide O1/O2/O3 --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 13 +++++++++++++ 1 file changed, 13 insertions(+) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index 3f4db985d..e0df21860 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -296,6 +296,19 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USB { #ifdef FSDEV_BUS_32BIT (void) USBx; + volatile uint32_t count = 10; + /* + WA: few cycles for RX PMA descriptor to update + This workaround is ported from stm32h5xx_hal_pcd.h : PCD_GET_EP_RX_CNT H5 + This code fixes an issue when the code is compiled in GCC with a fast optimization(O2/O3) and device with an high frequency. + The function doesn't return the correct value. + Issue observed on Windows 10 and stm32h573i_dk and tud_task() scheduled by IT, the device is not migrated the USB device is not visible . + */ + while (count > 0U) + { + asm("NOP"); + count--; + } return (pma32[2*bEpIdx + 1] & 0x03FF0000) >> 16; #else __I uint16_t *regPtr = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); -- cgit v1.3.1 From 5630030a22cc850672c62bfe3a12c0054a7f84a2 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 15 Mar 2024 20:39:45 +0700 Subject: improve uvc debug message --- src/class/video/video.h | 23 ++-- src/class/video/video_device.c | 223 ++++++++++++++++++++++------------ src/device/usbd.c | 2 +- src/portable/nordic/nrf5x/dcd_nrf5x.c | 4 +- 4 files changed, 157 insertions(+), 95 deletions(-) (limited to 'src/portable') diff --git a/src/class/video/video.h b/src/class/video/video.h index abf1e34b9..b8a9b6369 100644 --- a/src/class/video/video.h +++ b/src/class/video/video.h @@ -160,22 +160,23 @@ typedef enum { /* A.9.1 VideoControl Interface Control Selectors */ typedef enum { VIDEO_VC_CTL_UNDEFINED = 0x00, - VIDEO_VC_CTL_VIDEO_POWER_MODE, - VIDEO_VC_CTL_REQUEST_ERROR_CODE, + VIDEO_VC_CTL_VIDEO_POWER_MODE, // 0x01 + VIDEO_VC_CTL_REQUEST_ERROR_CODE, // 0x02 } video_interface_control_selector_t; /* A.9.8 VideoStreaming Interface Control Selectors */ typedef enum { VIDEO_VS_CTL_UNDEFINED = 0x00, - VIDEO_VS_CTL_PROBE, - VIDEO_VS_CTL_COMMIT, - VIDEO_VS_CTL_STILL_PROBE, - VIDEO_VS_CTL_STILL_COMMIT, - VIDEO_VS_CTL_STILL_IMAGE_TRIGGER, - VIDEO_VS_CTL_STREAM_ERROR_CODE, - VIDEO_VS_CTL_GENERATE_KEY_FRAME, - VIDEO_VS_CTL_UPDATE_FRAME_SEGMENT, - VIDEO_VS_CTL_SYNCH_DELAY_CONTROL, + VIDEO_VS_CTL_PROBE, // 0x01 + VIDEO_VS_CTL_COMMIT, // 0x02 + VIDEO_VS_CTL_STILL_PROBE, // 0x03 + VIDEO_VS_CTL_STILL_COMMIT, // 0x04 + VIDEO_VS_CTL_STILL_IMAGE_TRIGGER, // 0x05 + VIDEO_VS_CTL_STREAM_ERROR_CODE, // 0x06 + VIDEO_VS_CTL_GENERATE_KEY_FRAME, // 0x07 + VIDEO_VS_CTL_UPDATE_FRAME_SEGMENT, // 0x08 + VIDEO_VS_CTL_SYNCH_DELAY_CONTROL, // 0x09 + } video_interface_streaming_selector_t; /* B. Terminal Types */ diff --git a/src/class/video/video_device.c b/src/class/video/video_device.c index 249ced83d..dc3f8d897 100644 --- a/src/class/video/video_device.c +++ b/src/class/video/video_device.c @@ -143,13 +143,65 @@ CFG_TUD_MEM_SECTION tu_static videod_streaming_interface_t _videod_streaming_itf tu_static uint8_t const _cap_get = 0x1u; /* support for GET */ tu_static uint8_t const _cap_get_set = 0x3u; /* support for GET and SET */ +//--------------------------------------------------------------------+ +// Debug +//--------------------------------------------------------------------+ +#if CFG_TUSB_DEBUG >= CFG_TUD_VIDEO_LOG_LEVEL + +static tu_lookup_entry_t const tu_lookup_video_request[] = { + {.key = VIDEO_REQUEST_UNDEFINED, .data = "Undefined"}, + {.key = VIDEO_REQUEST_SET_CUR, .data = "SetCur"}, + {.key = VIDEO_REQUEST_SET_CUR_ALL, .data = "SetCurAll"}, + {.key = VIDEO_REQUEST_GET_CUR, .data = "GetCur"}, + {.key = VIDEO_REQUEST_GET_MIN, .data = "GetMin"}, + {.key = VIDEO_REQUEST_GET_MAX, .data = "GetMax"}, + {.key = VIDEO_REQUEST_GET_RES, .data = "GetRes"}, + {.key = VIDEO_REQUEST_GET_LEN, .data = "GetLen"}, + {.key = VIDEO_REQUEST_GET_INFO, .data = "GetInfo"}, + {.key = VIDEO_REQUEST_GET_DEF, .data = "GetDef"}, + {.key = VIDEO_REQUEST_GET_CUR_ALL, .data = "GetCurAll"}, + {.key = VIDEO_REQUEST_GET_MIN_ALL, .data = "GetMinAll"}, + {.key = VIDEO_REQUEST_GET_MAX_ALL, .data = "GetMaxAll"}, + {.key = VIDEO_REQUEST_GET_RES_ALL, .data = "GetResAll"}, + {.key = VIDEO_REQUEST_GET_DEF_ALL, .data = "GetDefAll"}, +}; + +static tu_lookup_table_t const tu_table_video_request = { + .count = TU_ARRAY_SIZE(tu_lookup_video_request), + .items = tu_lookup_video_request +}; + +static char const* const tu_str_video_vc_control_selector[] = { + "Undefined", + "Video Power Mode", + "Request Error Code", +}; + +static char const* const tu_str_video_vs_control_selector[] = { + "Undefined", + "Probe", + "Commit", + "Still Probe", + "Still Commit", + "Still Image Trigger", + "Stream Error Code", + "Generate Key Frame", + "Update Frame Segment", + "Sync Delay", +}; + +#endif + +//--------------------------------------------------------------------+ +// +//--------------------------------------------------------------------+ + /** Get interface number from the interface descriptor * * @param[in] desc interface descriptor * * @return bInterfaceNumber */ -static inline uint8_t _desc_itfnum(void const *desc) -{ +static inline uint8_t _desc_itfnum(void const *desc) { return ((uint8_t const*)desc)[2]; } @@ -158,8 +210,7 @@ static inline uint8_t _desc_itfnum(void const *desc) * @param[in] desc endpoint descriptor * * @return bEndpointAddress */ -static inline uint8_t _desc_ep_addr(void const *desc) -{ +static inline uint8_t _desc_ep_addr(void const *desc) { return ((uint8_t const*)desc)[2]; } @@ -169,8 +220,7 @@ static inline uint8_t _desc_ep_addr(void const *desc) * @param[in] stm_idx index number of streaming interface * * @return instance */ -static videod_streaming_interface_t* _get_instance_streaming(uint_fast8_t ctl_idx, uint_fast8_t stm_idx) -{ +static videod_streaming_interface_t* _get_instance_streaming(uint_fast8_t ctl_idx, uint_fast8_t stm_idx) { videod_interface_t *ctl = &_videod_itf[ctl_idx]; if (!ctl->beg) return NULL; videod_streaming_interface_t *stm = &_videod_streaming_itf[ctl->stm[stm_idx]]; @@ -178,13 +228,11 @@ static videod_streaming_interface_t* _get_instance_streaming(uint_fast8_t ctl_id return stm; } -static tusb_desc_vc_itf_t const* _get_desc_vc(videod_interface_t const *self) -{ +static tusb_desc_vc_itf_t const* _get_desc_vc(videod_interface_t const *self) { return (tusb_desc_vc_itf_t const *)(self->beg + self->cur); } -static tusb_desc_vs_itf_t const* _get_desc_vs(videod_streaming_interface_t const *self) -{ +static tusb_desc_vs_itf_t const* _get_desc_vs(videod_streaming_interface_t const *self) { if (!self->desc.cur) return NULL; uint8_t const *desc = _videod_itf[self->index_vc].beg; return (tusb_desc_vs_itf_t const*)(desc + self->desc.cur); @@ -198,8 +246,7 @@ static tusb_desc_vs_itf_t const* _get_desc_vs(videod_streaming_interface_t const * * @return The pointer for interface descriptor. * @retval end did not found interface descriptor */ -static void const* _find_desc(void const *beg, void const *end, uint_fast8_t desc_type) -{ +static void const* _find_desc(void const *beg, void const *end, uint_fast8_t desc_type) { void const *cur = beg; while ((cur < end) && (desc_type != tu_desc_type(cur))) { cur = tu_desc_next(cur); @@ -238,8 +285,7 @@ static void const* _find_desc_2_type(void const *beg, void const *end, uint_fast static void const* _find_desc_3(void const *beg, void const *end, uint_fast8_t desc_type, uint_fast8_t element_0, - uint_fast8_t element_1) -{ + uint_fast8_t element_1) { for (void const *cur = beg; cur < end; cur = _find_desc(cur, end, desc_type)) { uint8_t const *p = (uint8_t const *)cur; if ((p[2] == element_0) && (p[3] == element_1)) { @@ -261,8 +307,7 @@ static void const* _find_desc_3(void const *beg, void const *end, * * @return The pointer for interface descriptor. * @retval end did not found interface descriptor */ -static void const* _next_desc_itf(void const *beg, void const *end) -{ +static void const* _next_desc_itf(void const *beg, void const *end) { void const *cur = beg; uint_fast8_t itfnum = ((tusb_desc_interface_t const*)cur)->bInterfaceNumber; while ((cur < end) && @@ -413,8 +458,10 @@ static bool _update_streaming_parameters(videod_streaming_interface_t const *stm case VIDEO_CS_ITF_VS_FORMAT_UNCOMPRESSED: param->wCompQuality = 1; /* 1 to 10000 */ break; - case VIDEO_CS_ITF_VS_FORMAT_MJPEG: + + case VIDEO_CS_ITF_VS_FORMAT_MJPEG: break; + default: return false; } @@ -435,9 +482,11 @@ static bool _update_streaming_parameters(videod_streaming_interface_t const *stm case VIDEO_CS_ITF_VS_FORMAT_UNCOMPRESSED: frame_size = (uint_fast32_t)frm->wWidth * frm->wHeight * fmt->uncompressed.bBitsPerPixel / 8; break; + case VIDEO_CS_ITF_VS_FORMAT_MJPEG: frame_size = (uint_fast32_t)frm->wWidth * frm->wHeight * 16 / 8; /* YUV422 */ break; + default: break; } param->dwMaxVideoFrameSize = frame_size; @@ -478,10 +527,12 @@ static bool _negotiate_streaming_parameters(videod_streaming_interface_t const * if (_get_desc_vs(stm)) param->bFormatIndex = _get_desc_vs(stm)->stm.bNumFormats; break; + case VIDEO_REQUEST_GET_MIN: case VIDEO_REQUEST_GET_DEF: param->bFormatIndex = 1; break; + default: return false; } /* Set the parameters determined by the format */ @@ -510,18 +561,22 @@ static bool _negotiate_streaming_parameters(videod_streaming_interface_t const * case VIDEO_REQUEST_GET_MAX: frmnum = fmt->bNumFrameDescriptors; break; + case VIDEO_REQUEST_GET_MIN: frmnum = 1; break; + case VIDEO_REQUEST_GET_DEF: switch (fmt->bDescriptorSubType) { - case VIDEO_CS_ITF_VS_FORMAT_UNCOMPRESSED: - frmnum = fmt->uncompressed.bDefaultFrameIndex; - break; - case VIDEO_CS_ITF_VS_FORMAT_MJPEG: - frmnum = fmt->mjpeg.bDefaultFrameIndex; - break; - default: return false; + case VIDEO_CS_ITF_VS_FORMAT_UNCOMPRESSED: + frmnum = fmt->uncompressed.bDefaultFrameIndex; + break; + + case VIDEO_CS_ITF_VS_FORMAT_MJPEG: + frmnum = fmt->mjpeg.bDefaultFrameIndex; + break; + + default: return false; } break; default: return false; @@ -534,9 +589,11 @@ static bool _negotiate_streaming_parameters(videod_streaming_interface_t const * case VIDEO_CS_ITF_VS_FORMAT_UNCOMPRESSED: frame_size = (uint_fast32_t)frm->wWidth * frm->wHeight * fmt->uncompressed.bBitsPerPixel / 8; break; + case VIDEO_CS_ITF_VS_FORMAT_MJPEG: frame_size = (uint_fast32_t)frm->wWidth * frm->wHeight * 16 / 8; /* YUV422 */ break; + default: return false; } param->dwMaxVideoFrameSize = frame_size; @@ -552,42 +609,43 @@ static bool _negotiate_streaming_parameters(videod_streaming_interface_t const * uint_fast32_t interval, interval_ms; switch (request) { - case VIDEO_REQUEST_GET_MAX: - { - uint_fast32_t min_interval, max_interval; - uint_fast8_t num_intervals = frm->uncompressed.bFrameIntervalType; - max_interval = num_intervals ? frm->uncompressed.dwFrameInterval[num_intervals - 1]: frm->uncompressed.dwFrameInterval[1]; - min_interval = frm->uncompressed.dwFrameInterval[0]; - interval = max_interval; - interval_ms = min_interval / 10000; - } + case VIDEO_REQUEST_GET_MAX: { + uint_fast32_t min_interval, max_interval; + uint_fast8_t num_intervals = frm->uncompressed.bFrameIntervalType; + max_interval = num_intervals ? frm->uncompressed.dwFrameInterval[num_intervals - 1]: frm->uncompressed.dwFrameInterval[1]; + min_interval = frm->uncompressed.dwFrameInterval[0]; + interval = max_interval; + interval_ms = min_interval / 10000; break; - case VIDEO_REQUEST_GET_MIN: - { - uint_fast32_t min_interval, max_interval; - uint_fast8_t num_intervals = frm->uncompressed.bFrameIntervalType; - max_interval = num_intervals ? frm->uncompressed.dwFrameInterval[num_intervals - 1]: frm->uncompressed.dwFrameInterval[1]; - min_interval = frm->uncompressed.dwFrameInterval[0]; - interval = min_interval; - interval_ms = max_interval / 10000; - } + } + + case VIDEO_REQUEST_GET_MIN: { + uint_fast32_t min_interval, max_interval; + uint_fast8_t num_intervals = frm->uncompressed.bFrameIntervalType; + max_interval = num_intervals ? frm->uncompressed.dwFrameInterval[num_intervals - 1]: frm->uncompressed.dwFrameInterval[1]; + min_interval = frm->uncompressed.dwFrameInterval[0]; + interval = min_interval; + interval_ms = max_interval / 10000; break; + } + case VIDEO_REQUEST_GET_DEF: interval = frm->uncompressed.dwDefaultFrameInterval; interval_ms = interval / 10000; break; - case VIDEO_REQUEST_GET_RES: - { - uint_fast8_t num_intervals = frm->uncompressed.bFrameIntervalType; - if (num_intervals) { - interval = 0; - interval_ms = 0; - } else { - interval = frm->uncompressed.dwFrameInterval[2]; - interval_ms = interval / 10000; - } + + case VIDEO_REQUEST_GET_RES: { + uint_fast8_t num_intervals = frm->uncompressed.bFrameIntervalType; + if (num_intervals) { + interval = 0; + interval_ms = 0; + } else { + interval = frm->uncompressed.dwFrameInterval[2]; + interval_ms = interval / 10000; } break; + } + default: return false; } param->dwFrameInterval = interval; @@ -681,8 +739,7 @@ static bool _init_vs_configuration(videod_streaming_interface_t *stm) /* initialize streaming settings */ stm->state = VS_STATE_PROBING; stm->max_payload_transfer_size = 0; - video_probe_and_commit_control_t *param = - (video_probe_and_commit_control_t *)&stm->ep_buf; + video_probe_and_commit_control_t *param = (video_probe_and_commit_control_t *)&stm->ep_buf; tu_memclr(param, sizeof(*param)); return _update_streaming_parameters(stm, param); } @@ -760,6 +817,10 @@ static uint_fast16_t _prepare_in_payload(videod_streaming_interface_t *stm) pkt_len = hdr_len + remaining; } uint_fast16_t data_len = pkt_len - hdr_len; + TU_LOG2(" prepare remain = %u, hdr_len = %u, pkt_len = %u, offset = %lu, data_len = %u\r\n", remaining, hdr_len, pkt_len, stm->offset, data_len); + if ( data_len > sizeof(stm->ep_buf) ) { + TU_BREAKPOINT(); + } memcpy(&stm->ep_buf[hdr_len], stm->buffer + stm->offset, data_len); stm->offset += data_len; remaining -= data_len; @@ -775,6 +836,7 @@ static int handle_video_ctl_std_req(uint8_t rhport, uint8_t stage, tusb_control_request_t const *request, uint_fast8_t ctl_idx) { + TU_LOG_DRV("\r\n"); switch (request->bRequest) { case TUSB_REQ_GET_INTERFACE: if (stage == CONTROL_STAGE_SETUP) @@ -812,7 +874,10 @@ static int handle_video_ctl_cs_req(uint8_t rhport, uint8_t stage, videod_interface_t *self = &_videod_itf[ctl_idx]; /* 4.2.1 Interface Control Request */ - switch (TU_U16_HIGH(request->wValue)) { + uint8_t const ctrl_sel = TU_U16_HIGH(request->wValue); + TU_LOG_DRV("%s_Control(%s)\r\n", tu_str_video_vc_control_selector[ctrl_sel], tu_lookup_find(&tu_table_video_request, request->bRequest)); + + switch (ctrl_sel) { case VIDEO_VC_CTL_VIDEO_POWER_MODE: switch (request->bRequest) { case VIDEO_REQUEST_SET_CUR: @@ -876,19 +941,19 @@ static int handle_video_ctl_req(uint8_t rhport, uint8_t stage, tusb_control_request_t const *request, uint_fast8_t ctl_idx) { - uint_fast8_t entity_id; switch (request->bmRequestType_bit.type) { case TUSB_REQ_TYPE_STANDARD: return handle_video_ctl_std_req(rhport, stage, request, ctl_idx); - case TUSB_REQ_TYPE_CLASS: - entity_id = TU_U16_HIGH(request->wIndex); + case TUSB_REQ_TYPE_CLASS: { + uint_fast8_t entity_id = TU_U16_HIGH(request->wIndex); if (!entity_id) { return handle_video_ctl_cs_req(rhport, stage, request, ctl_idx); } else { TU_VERIFY(_find_desc_entity(_get_desc_vc(&_videod_itf[ctl_idx]), entity_id), VIDEO_ERROR_INVALID_REQUEST); return VIDEO_ERROR_NONE; } + } default: return VIDEO_ERROR_INVALID_REQUEST; @@ -899,6 +964,7 @@ static int handle_video_stm_std_req(uint8_t rhport, uint8_t stage, tusb_control_request_t const *request, uint_fast8_t stm_idx) { + TU_LOG_DRV("\r\n"); videod_streaming_interface_t *self = &_videod_streaming_itf[stm_idx]; switch (request->bRequest) { case TUSB_REQ_GET_INTERFACE: @@ -914,8 +980,7 @@ static int handle_video_stm_std_req(uint8_t rhport, uint8_t stage, return VIDEO_ERROR_NONE; case TUSB_REQ_SET_INTERFACE: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { TU_VERIFY(_open_vs_itf(rhport, self, request->wValue), VIDEO_ERROR_UNKNOWN); tud_control_status(rhport, request); } @@ -929,26 +994,26 @@ static int handle_video_stm_std_req(uint8_t rhport, uint8_t stage, static int handle_video_stm_cs_req(uint8_t rhport, uint8_t stage, tusb_control_request_t const *request, - uint_fast8_t stm_idx) -{ + uint_fast8_t stm_idx) { (void)rhport; videod_streaming_interface_t *self = &_videod_streaming_itf[stm_idx]; + uint8_t const ctrl_sel = TU_U16_HIGH(request->wValue); + TU_LOG_DRV("%s_Control(%s)\r\n", tu_str_video_vs_control_selector[ctrl_sel], tu_lookup_find(&tu_table_video_request, request->bRequest)); + /* 4.2.1 Interface Control Request */ - switch (TU_U16_HIGH(request->wValue)) { + switch (ctrl_sel) { case VIDEO_VS_CTL_STREAM_ERROR_CODE: switch (request->bRequest) { case VIDEO_REQUEST_GET_CUR: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { /* TODO */ TU_VERIFY(tud_control_xfer(rhport, request, &self->error_code, sizeof(uint8_t)), VIDEO_ERROR_UNKNOWN); } return VIDEO_ERROR_NONE; case VIDEO_REQUEST_GET_INFO: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { TU_VERIFY(tud_control_xfer(rhport, request, (uint8_t*)(uintptr_t) &_cap_get, sizeof(_cap_get)), VIDEO_ERROR_UNKNOWN); } return VIDEO_ERROR_NONE; @@ -962,6 +1027,7 @@ static int handle_video_stm_cs_req(uint8_t rhport, uint8_t stage, self->state = VS_STATE_PROBING; _init_vs_configuration(self); } + switch (request->bRequest) { case VIDEO_REQUEST_SET_CUR: if (stage == CONTROL_STAGE_SETUP) { @@ -975,8 +1041,7 @@ static int handle_video_stm_cs_req(uint8_t rhport, uint8_t stage, return VIDEO_ERROR_NONE; case VIDEO_REQUEST_GET_CUR: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { TU_VERIFY(request->wLength, VIDEO_ERROR_UNKNOWN); TU_VERIFY(tud_control_xfer(rhport, request, self->ep_buf, sizeof(video_probe_and_commit_control_t)), VIDEO_ERROR_UNKNOWN); } @@ -986,8 +1051,7 @@ static int handle_video_stm_cs_req(uint8_t rhport, uint8_t stage, case VIDEO_REQUEST_GET_MAX: case VIDEO_REQUEST_GET_RES: case VIDEO_REQUEST_GET_DEF: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { TU_VERIFY(request->wLength, VIDEO_ERROR_UNKNOWN); video_probe_and_commit_control_t tmp; tmp = *(video_probe_and_commit_control_t*)&self->ep_buf; @@ -997,8 +1061,7 @@ static int handle_video_stm_cs_req(uint8_t rhport, uint8_t stage, return VIDEO_ERROR_NONE; case VIDEO_REQUEST_GET_LEN: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { TU_VERIFY(2 == request->wLength, VIDEO_ERROR_UNKNOWN); uint16_t len = sizeof(video_probe_and_commit_control_t); TU_VERIFY(tud_control_xfer(rhport, request, (uint8_t*)&len, sizeof(len)), VIDEO_ERROR_UNKNOWN); @@ -1006,8 +1069,7 @@ static int handle_video_stm_cs_req(uint8_t rhport, uint8_t stage, return VIDEO_ERROR_NONE; case VIDEO_REQUEST_GET_INFO: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { TU_VERIFY(1 == request->wLength, VIDEO_ERROR_UNKNOWN); TU_VERIFY(tud_control_xfer(rhport, request, (uint8_t*)(uintptr_t)&_cap_get_set, sizeof(_cap_get_set)), VIDEO_ERROR_UNKNOWN); } @@ -1046,16 +1108,14 @@ static int handle_video_stm_cs_req(uint8_t rhport, uint8_t stage, return VIDEO_ERROR_NONE; case VIDEO_REQUEST_GET_CUR: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { TU_VERIFY(request->wLength, VIDEO_ERROR_UNKNOWN); TU_VERIFY(tud_control_xfer(rhport, request, self->ep_buf, sizeof(video_probe_and_commit_control_t)), VIDEO_ERROR_UNKNOWN); } return VIDEO_ERROR_NONE; case VIDEO_REQUEST_GET_LEN: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { TU_VERIFY(2 == request->wLength, VIDEO_ERROR_UNKNOWN); uint16_t len = sizeof(video_probe_and_commit_control_t); TU_VERIFY(tud_control_xfer(rhport, request, (uint8_t*)&len, sizeof(len)), VIDEO_ERROR_UNKNOWN); @@ -1063,8 +1123,7 @@ static int handle_video_stm_cs_req(uint8_t rhport, uint8_t stage, return VIDEO_ERROR_NONE; case VIDEO_REQUEST_GET_INFO: - if (stage == CONTROL_STAGE_SETUP) - { + if (stage == CONTROL_STAGE_SETUP) { TU_VERIFY(1 == request->wLength, VIDEO_ERROR_UNKNOWN); TU_VERIFY(tud_control_xfer(rhport, request, (uint8_t*)(uintptr_t) &_cap_get_set, sizeof(_cap_get_set)), VIDEO_ERROR_UNKNOWN); } @@ -1264,6 +1323,7 @@ bool videod_control_xfer_cb(uint8_t rhport, uint8_t stage, tusb_control_request_ } if (itf < CFG_TUD_VIDEO) { + TU_LOG_DRV(" VC[%d]: ", itf); err = handle_video_ctl_req(rhport, stage, request, itf); _videod_itf[itf].error_code = (uint8_t)err; if (err) return false; @@ -1279,6 +1339,7 @@ bool videod_control_xfer_cb(uint8_t rhport, uint8_t stage, tusb_control_request_ } if (itf < CFG_TUD_VIDEO_STREAMING) { + TU_LOG_DRV(" VS[%d]: ", itf); err = handle_video_stm_req(rhport, stage, request, itf); _videod_streaming_itf[itf].error_code = (uint8_t)err; if (err) return false; diff --git a/src/device/usbd.c b/src/device/usbd.c index ab572e095..96d0b698b 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -319,7 +319,7 @@ void usbd_driver_print_control_complete_name(usbd_control_xfer_cb_t callback) { for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) { usbd_class_driver_t const* driver = get_driver(i); if (driver && driver->control_xfer_cb == callback) { - TU_LOG_USBD(" %s control complete\r\n", driver->name); + TU_LOG_USBD("%s control complete\r\n", driver->name); return; } } diff --git a/src/portable/nordic/nrf5x/dcd_nrf5x.c b/src/portable/nordic/nrf5x/dcd_nrf5x.c index 841cda752..80a285ef0 100644 --- a/src/portable/nordic/nrf5x/dcd_nrf5x.c +++ b/src/portable/nordic/nrf5x/dcd_nrf5x.c @@ -246,7 +246,7 @@ static void xact_in_dma(uint8_t epnum) //--------------------------------------------------------------------+ void dcd_init (uint8_t rhport) { - TU_LOG1("dcd init\r\n"); + TU_LOG2("dcd init\r\n"); (void) rhport; } @@ -685,7 +685,7 @@ void dcd_int_handler(uint8_t rhport) if ( int_status & USBD_INTEN_USBEVENT_Msk ) { - TU_LOG(2, "EVENTCAUSE = 0x%04lX\r\n", NRF_USBD->EVENTCAUSE); + TU_LOG(3, "EVENTCAUSE = 0x%04lX\r\n", NRF_USBD->EVENTCAUSE); enum { EVT_CAUSE_MASK = USBD_EVENTCAUSE_SUSPEND_Msk | USBD_EVENTCAUSE_RESUME_Msk | USBD_EVENTCAUSE_USBWUALLOWED_Msk | USBD_EVENTCAUSE_ISOOUTCRC_Msk }; uint32_t const evt_cause = NRF_USBD->EVENTCAUSE & EVT_CAUSE_MASK; -- cgit v1.3.1 From 61a31db8ecf66460e4888aef7915da66d98964d0 Mon Sep 17 00:00:00 2001 From: Scott Shawcroft Date: Wed, 20 Mar 2024 15:20:24 -0700 Subject: Tweaks for ESP-IDF 5.2.1 --- src/portable/espressif/esp32sx/dcd_esp32sx.c | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/espressif/esp32sx/dcd_esp32sx.c b/src/portable/espressif/esp32sx/dcd_esp32sx.c index 1fcfb6241..bfc0baa56 100644 --- a/src/portable/espressif/esp32sx/dcd_esp32sx.c +++ b/src/portable/espressif/esp32sx/dcd_esp32sx.c @@ -31,16 +31,26 @@ #if (((CFG_TUSB_MCU == OPT_MCU_ESP32S2) || (CFG_TUSB_MCU == OPT_MCU_ESP32S3)) && CFG_TUD_ENABLED) // Espressif -#include "freertos/xtensa_api.h" +#include "xtensa_api.h" #include "esp_intr_alloc.h" #include "esp_log.h" #include "soc/dport_reg.h" #include "soc/gpio_sig_map.h" #include "soc/usb_periph.h" +#include "soc/usb_reg.h" +#include "soc/usb_struct.h" #include "soc/periph_defs.h" // for interrupt source #include "device/dcd.h" +#ifndef USB_OUT_EP_NUM +#define USB_OUT_EP_NUM ((int) (sizeof(USB0.out_ep_reg) / sizeof(USB0.out_ep_reg[0]))) +#endif + +#ifndef USB_IN_EP_NUM +#define USB_IN_EP_NUM ((int) (sizeof(USB0.in_ep_reg) / sizeof(USB0.in_ep_reg[0]))) +#endif + // Max number of bi-directional endpoints including EP0 // Note: ESP32S2 specs say there are only up to 5 IN active endpoints include EP0 // We should probably prohibit enabling Endpoint IN > 4 (not done yet) -- cgit v1.3.1 From 0610070d07babf3623016603325afa938d4fc9f7 Mon Sep 17 00:00:00 2001 From: Ha Thach Date: Mon, 25 Mar 2024 18:44:51 +0700 Subject: Update dcd_stm32_fsdev_pvt_st.h --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 17 +++++++---------- 1 file changed, 7 insertions(+), 10 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index e0df21860..5a129ecf8 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -296,17 +296,14 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USB { #ifdef FSDEV_BUS_32BIT (void) USBx; - volatile uint32_t count = 10; - /* - WA: few cycles for RX PMA descriptor to update - This workaround is ported from stm32h5xx_hal_pcd.h : PCD_GET_EP_RX_CNT H5 - This code fixes an issue when the code is compiled in GCC with a fast optimization(O2/O3) and device with an high frequency. - The function doesn't return the correct value. - Issue observed on Windows 10 and stm32h573i_dk and tud_task() scheduled by IT, the device is not migrated the USB device is not visible . + /* WA: few cycles for RX PMA descriptor to update, otherwise doesn't return the correct value. + Note: required for G0, U5, H5 etc. + This workaround is ported from stm32h5xx_hal_pcd.h and fixes the issue when calling this function fast enough. + Reproduced with GCC ast optimization(O2/O3) and stm32h573i_dk with an high frequency. + Observed on Windows 10 where tud_task() is scheduled by interrupt handler. */ - while (count > 0U) - { - asm("NOP"); + volatile uint32_t count = 10; // defined as PCD_RX_PMA_CNT in stm32 hal_driver + while (count > 0U) { count--; } return (pma32[2*bEpIdx + 1] & 0x03FF0000) >> 16; -- cgit v1.3.1 From 29f016ae15eb94654748bf29b81557f6ab611384 Mon Sep 17 00:00:00 2001 From: Ha Thach Date: Mon, 25 Mar 2024 18:59:05 +0700 Subject: fix pre-commit --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index 5a129ecf8..ade64b4fb 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -297,9 +297,9 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USB #ifdef FSDEV_BUS_32BIT (void) USBx; /* WA: few cycles for RX PMA descriptor to update, otherwise doesn't return the correct value. - Note: required for G0, U5, H5 etc. + Note: required for G0, U5, H5 etc. This workaround is ported from stm32h5xx_hal_pcd.h and fixes the issue when calling this function fast enough. - Reproduced with GCC ast optimization(O2/O3) and stm32h573i_dk with an high frequency. + Reproduced with GCC ast optimization(O2/O3) and stm32h573i_dk with an high frequency. Observed on Windows 10 where tud_task() is scheduled by interrupt handler. */ volatile uint32_t count = 10; // defined as PCD_RX_PMA_CNT in stm32 hal_driver -- cgit v1.3.1 From fbb20373c1b22c8eb1aed4fa95972c851be819f3 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 26 Mar 2024 10:26:42 +0700 Subject: implement hcd_deinit() for max3421 --- src/portable/analog/max3421/hcd_max3421.c | 35 ++++++++++++++++++++++++------- 1 file changed, 27 insertions(+), 8 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index cc4799dd6..d70cf7208 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -321,35 +321,35 @@ static void fifo_read(uint8_t rhport, uint8_t * buffer, uint16_t len, bool in_is } //------------- register write helper -------------// -static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr) { +TU_ATTR_ALWAYS_INLINE static inline void hirq_write(uint8_t rhport, uint8_t data, bool in_isr) { reg_write(rhport, HIRQ_ADDR, data, in_isr); // HIRQ write 1 is clear _hcd_data.hirq &= (uint8_t) ~data; } -static inline void hien_write(uint8_t rhport, uint8_t data, bool in_isr) { +TU_ATTR_ALWAYS_INLINE static inline void hien_write(uint8_t rhport, uint8_t data, bool in_isr) { _hcd_data.hien = data; reg_write(rhport, HIEN_ADDR, data, in_isr); } -static inline void mode_write(uint8_t rhport, uint8_t data, bool in_isr) { +TU_ATTR_ALWAYS_INLINE static inline void mode_write(uint8_t rhport, uint8_t data, bool in_isr) { _hcd_data.mode = data; reg_write(rhport, MODE_ADDR, data, in_isr); } -static inline void peraddr_write(uint8_t rhport, uint8_t data, bool in_isr) { +TU_ATTR_ALWAYS_INLINE static inline void peraddr_write(uint8_t rhport, uint8_t data, bool in_isr) { if ( _hcd_data.peraddr == data ) return; // no need to change address _hcd_data.peraddr = data; reg_write(rhport, PERADDR_ADDR, data, in_isr); } -static inline void hxfr_write(uint8_t rhport, uint8_t data, bool in_isr) { +TU_ATTR_ALWAYS_INLINE static inline void hxfr_write(uint8_t rhport, uint8_t data, bool in_isr) { _hcd_data.hxfr = data; reg_write(rhport, HXFR_ADDR, data, in_isr); } -static inline void sndbc_write(uint8_t rhport, uint8_t data, bool in_isr) { +TU_ATTR_ALWAYS_INLINE static inline void sndbc_write(uint8_t rhport, uint8_t data, bool in_isr) { _hcd_data.sndbc = data; reg_write(rhport, SNDBC_ADDR, data, in_isr); } @@ -449,7 +449,7 @@ bool hcd_init(uint8_t rhport) { // full duplex, interrupt negative edge reg_write(rhport, PINCTL_ADDR, PINCTL_FDUPSPI, false); - // V1 is 0x01, V2 is 0x12, V3 is 0x13 + // v1 is 0x01, v2 is 0x12, v3 is 0x13 uint8_t const revision = reg_read(rhport, REVISION_ADDR, false); TU_ASSERT(revision == 0x01 || revision == 0x12 || revision == 0x13, false); TU_LOG2_HEX(revision); @@ -481,6 +481,24 @@ bool hcd_init(uint8_t rhport) { return true; } +bool hcd_deinit(uint8_t rhport) { + (void) rhport; + + // disable interrupt + tuh_max3421_int_api(rhport, false); + + // reset max3421 + reg_write(rhport, USBCTL_ADDR, USBCTL_CHIPRES, false); + reg_write(rhport, USBCTL_ADDR, 0, false); + + #if OSAL_MUTEX_REQUIRED + osal_mutex_delete(_hcd_data.spi_mutex); + _hcd_data.spi_mutex = NULL; + #endif + + return true; +} + // Enable USB interrupt // Not actually enable GPIO interrupt, just set variable to prevent handler to process void hcd_int_enable (uint8_t rhport) { @@ -598,7 +616,8 @@ void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { hxfr_write(rhport, hxfr, in_isr); } -TU_ATTR_ALWAYS_INLINE static inline void xact_inout(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { +TU_ATTR_ALWAYS_INLINE static inline +void xact_inout(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { if (ep->ep_num == 0 ) { // setup if (ep->is_setup) { -- cgit v1.3.1 From 9fdb1c1684c653426d4f616d788b329ee528110a Mon Sep 17 00:00:00 2001 From: IngHK Date: Tue, 26 Mar 2024 08:10:32 +0100 Subject: draft MAX3421E NAK retry handling next frame --- src/portable/analog/max3421/hcd_max3421.c | 45 ++++++++++++++++++++++++++++++- 1 file changed, 44 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index d70cf7208..d366298ea 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -28,6 +28,8 @@ #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 +#define NAK_RETRY_HANDLING 1 + #include #include "host/hcd.h" @@ -180,6 +182,9 @@ typedef struct { uint8_t data_toggle : 1; uint8_t xfer_pending : 1; uint8_t xfer_complete : 1; +#if NAK_RETRY_HANDLING + uint8_t retry_pending : 1; +#endif }; struct TU_ATTR_PACKED { @@ -593,7 +598,7 @@ void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { } uint8_t const xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); - TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ,); +// TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ,); if (xact_len) { fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, in_isr); } @@ -803,6 +808,7 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { xfer_result_t xfer_result; switch(hresult) { case HRSL_SUCCESS: +// putchar('S'); xfer_result = XFER_RESULT_SUCCESS; break; @@ -811,6 +817,19 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { break; case HRSL_NAK: +// putchar('N'); +#if NAK_RETRY_HANDLING + ep->retry_pending = 1; + ep->xfer_pending = 0; + max3421_ep_t * next_ep = find_next_pending_ep(ep); + if (next_ep) { + // switch to next pending TODO could have issue with double buffered if not clear previously out data + xact_inout(rhport, next_ep, true, in_isr); + } else { + // no more pending + atomic_flag_clear(&_hcd_data.busy); + } +#else if (ep_num == 0) { // NAK on control, retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); @@ -828,6 +847,7 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { TU_ASSERT(false,); } } +#endif return; case HRSL_BAD_REQ: @@ -909,6 +929,29 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { if (hirq & HIRQ_FRAME_IRQ) { _hcd_data.frame_count++; + +#if NAK_RETRY_HANDLING + // retry EPs + max3421_ep_t * next_ep = NULL; + for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { + max3421_ep_t * ep = &_hcd_data.ep[i]; + // set retryable EPs to pending + if (ep->retry_pending) { +// putchar('R'); + ep->xfer_pending = 1; + ep->retry_pending = 0; + if (next_ep == NULL) { + next_ep = &_hcd_data.ep[i]; + } + } + } + // trigger 1st retryable EP + if (next_ep) { + if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { + xact_inout(rhport, next_ep, true, in_isr); + } + } +#endif } if (hirq & HIRQ_CONDET_IRQ) { -- cgit v1.3.1 From 307cce92c4f630ab988e6eb1e77685bc1e82d85a Mon Sep 17 00:00:00 2001 From: Camila Date: Tue, 26 Mar 2024 18:40:22 +0100 Subject: Improved SDK 3.2.0 compatibility - Used usbdev_allocreq for compatibility with SDK 3.2.0 - Wrapped previous code in #ifdef for legacy compatibility --- src/portable/sony/cxd56/dcd_cxd56.c | 29 ++++++++++------------------- 1 file changed, 10 insertions(+), 19 deletions(-) (limited to 'src/portable') diff --git a/src/portable/sony/cxd56/dcd_cxd56.c b/src/portable/sony/cxd56/dcd_cxd56.c index 9a939bc6c..83cd0718c 100644 --- a/src/portable/sony/cxd56/dcd_cxd56.c +++ b/src/portable/sony/cxd56/dcd_cxd56.c @@ -39,25 +39,6 @@ #define CXD56_SETUP_QUEUE_DEPTH (4) #define CXD56_MAX_DATA_OUT_SIZE (64) -/* Allocate/free I/O requests. - * Should not be called from interrupt processing! - */ - -#define EP_ALLOCREQ(ep) (ep)->ops->allocreq(ep) -#define EP_FREEREQ(ep,req) (ep)->ops->freereq(ep,req) - -/* Allocate/free an I/O buffer. - * Should not be called from interrupt processing! - */ - -#ifdef CONFIG_USBDEV_DMA -# define EP_ALLOCBUFFER(ep,nb) (ep)->ops->allocbuffer(ep,nb) -# define EP_FREEBUFFER(ep,buf) (ep)->ops->freebuffer(ep,buf) -#else -# define EP_ALLOCBUFFER(ep,nb) kmm_malloc(nb) -# define EP_FREEBUFFER(ep,buf) kmm_free(buf) -#endif - OSAL_QUEUE_DEF(usbd_int_set, _setup_queue_def, CXD56_SETUP_QUEUE_DEPTH, struct usb_ctrlreq_s); struct usbdcd_driver_s @@ -121,6 +102,7 @@ static int _dcd_bind(FAR struct usbdevclass_driver_s *driver, FAR struct usbdev_ usbdev = dev; usbdcd_driver.ep[0] = dev->ep0; + #ifdef EP_ALLOCREQ usbdcd_driver.req[0] = EP_ALLOCREQ(usbdcd_driver.ep[0]); if (usbdcd_driver.req[0] != NULL) { @@ -132,6 +114,9 @@ static int _dcd_bind(FAR struct usbdevclass_driver_s *driver, FAR struct usbdev_ usbdcd_driver.req[0] = NULL; } } + #else + usbdcd_driver.req[0] = usbdev_allocreq(usbdcd_driver.ep[0],64); + #endif usbdcd_driver.req[0]->callback = usbdcd_ep0incomplete; @@ -314,12 +299,18 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const *p_endpoint_desc) } usbdcd_driver.req[epnum] = NULL; + + #ifdef EP_ALLOCREQ usbdcd_driver.req[epnum] = EP_ALLOCREQ(usbdcd_driver.ep[epnum]); if (usbdcd_driver.req[epnum] != NULL) { usbdcd_driver.req[epnum]->len = ep_mps; } else + #else + usbdcd_driver.req[epnum] = usbdev_allocreq(usbdcd_driver.ep[epnum], ep_mps); + if(usbdcd_driver.req[epnum] == NULL) + #endif { return false; } -- cgit v1.3.1 From b9400df4c8bd49f1dd1e3047ca2a2c0284fa785e Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 29 Mar 2024 11:23:36 +0700 Subject: fix rp2 debug build with level 3 --- src/portable/raspberrypi/rp2040/hcd_rp2040.c | 10 ++++------ 1 file changed, 4 insertions(+), 6 deletions(-) (limited to 'src/portable') diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 08aef9314..b351a9a07 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -113,7 +113,7 @@ static void __tusb_irq_path_func(_handle_buff_status_bit)(uint bit, struct hw_en static void __tusb_irq_path_func(hw_handle_buff_status)(void) { uint32_t remaining_buffers = usb_hw->buf_status; - pico_trace("buf_status 0x%08x\n", remaining_buffers); + pico_trace("buf_status 0x%08lx\n", remaining_buffers); // Check EPX first uint bit = 0b1; @@ -325,10 +325,8 @@ static void _hw_endpoint_init(struct hw_endpoint *ep, uint8_t dev_addr, uint8_t ep->wMaxPacketSize = wMaxPacketSize; ep->transfer_type = transfer_type; - pico_trace("hw_endpoint_init dev %d ep %d %s xfer %d\n", ep->dev_addr, tu_edpt_number(ep->ep_addr), - ep_dir_string[tu_edpt_dir(ep->ep_addr)], ep->transfer_type); - pico_trace("dev %d ep %d %s setup buffer @ 0x%p\n", ep->dev_addr, tu_edpt_number(ep->ep_addr), - ep_dir_string[tu_edpt_dir(ep->ep_addr)], ep->hw_data_buf); + pico_trace("hw_endpoint_init dev %d ep %02X xfer %d\n", ep->dev_addr, ep->ep_addr, ep->transfer_type); + pico_trace("dev %d ep %02X setup buffer @ 0x%p\n", ep->dev_addr, ep->ep_addr, ep->hw_data_buf); uint dpram_offset = hw_data_offset(ep->hw_data_buf); // Bits 0-5 should be 0 assert(!(dpram_offset & 0b111111)); @@ -343,7 +341,7 @@ static void _hw_endpoint_init(struct hw_endpoint *ep, uint8_t dev_addr, uint8_t ep_reg |= (uint32_t) ((bmInterval - 1) << EP_CTRL_HOST_INTERRUPT_INTERVAL_LSB); } *ep->endpoint_control = ep_reg; - pico_trace("endpoint control (0x%p) <- 0x%x\n", ep->endpoint_control, ep_reg); + pico_trace("endpoint control (0x%p) <- 0x%lx\n", ep->endpoint_control, ep_reg); ep->configured = true; if ( ep != &epx ) -- cgit v1.3.1 From cab11064160deab42af654cd766bbfaca7f688cd Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Tue, 21 Nov 2023 18:06:57 +0100 Subject: dwc2: add endpoint allocation support. --- src/class/audio/audio_device.c | 4 +- src/portable/synopsys/dwc2/dcd_dwc2.c | 102 ++++++++++++++++++++++++++++++++++ 2 files changed, 104 insertions(+), 2 deletions(-) (limited to 'src/portable') diff --git a/src/class/audio/audio_device.c b/src/class/audio/audio_device.c index 4adc558a6..293defd96 100644 --- a/src/class/audio/audio_device.c +++ b/src/class/audio/audio_device.c @@ -96,8 +96,8 @@ #define USE_LINEAR_BUFFER 1 #endif -// Temporarily put the check here for stm32_fsdev -#ifdef TUP_USBIP_FSDEV +// Temporarily put the check here +#if defined(TUP_USBIP_FSDEV) || defined(TUP_USBIP_DWC2) #define USE_ISO_EP_ALLOCATION 1 #else #define USE_ISO_EP_ALLOCATION 0 diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index 3f00243e5..b0149a9a9 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -648,6 +648,108 @@ void dcd_edpt_close_all(uint8_t rhport) { _allocated_fifo_words_tx = 16; } +bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) +{ + (void)rhport; + + TU_ASSERT(largest_packet_size <= 1024); + + dwc2_regs_t* dwc2 = DWC2_REG(rhport); + uint8_t const ep_count = _dwc2_controller[rhport].ep_count; + + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); + + TU_ASSERT(epnum < ep_count); + + uint16_t const fifo_size = tu_div_ceil(largest_packet_size, 4); + + if (dir == TUSB_DIR_OUT) { + // Calculate required size of RX FIFO + uint16_t const sz = calc_grxfsiz(4 * fifo_size, ep_count); + + // If size_rx needs to be extended check if possible and if so enlarge it + if (dwc2->grxfsiz < sz) { + TU_ASSERT(sz + _allocated_fifo_words_tx <= _dwc2_controller[rhport].ep_fifo_size / 4); + + // Enlarge RX FIFO + dwc2->grxfsiz = sz; + } + + } else + { + // "USB Data FIFOs" section in reference manual + // Peripheral FIFO architecture + // + // --------------- 320 or 1024 ( 1280 or 4096 bytes ) + // | IN FIFO 0 | + // --------------- (320 or 1024) - 16 + // | IN FIFO 1 | + // --------------- (320 or 1024) - 16 - x + // | . . . . | + // --------------- (320 or 1024) - 16 - x - y - ... - z + // | IN FIFO MAX | + // --------------- + // | FREE | + // --------------- GRXFSIZ + // | OUT FIFO | + // | ( Shared ) | + // --------------- 0 + // + // In FIFO is allocated by following rules: + // - IN EP 1 gets FIFO 1, IN EP "n" gets FIFO "n". + + // Check if free space is available + TU_ASSERT(_allocated_fifo_words_tx + fifo_size + dwc2->grxfsiz <= _dwc2_controller[rhport].ep_fifo_size / 4); + + _allocated_fifo_words_tx += fifo_size; + + TU_LOG(DWC2_DEBUG, " Allocated %u bytes at offset %lu", fifo_size * 4, + _dwc2_controller[rhport].ep_fifo_size - _allocated_fifo_words_tx * 4); + + // DIEPTXF starts at FIFO #1. + // Both TXFD and TXSA are in unit of 32-bit words. + dwc2->dieptxf[epnum - 1] = (fifo_size << DIEPTXF_INEPTXFD_Pos) | + (_dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx); + } + + return true; +} + +bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) +{ + (void)rhport; + + dwc2_regs_t* dwc2 = DWC2_REG(rhport); + + uint8_t const epnum = tu_edpt_number(p_endpoint_desc->bEndpointAddress); + uint8_t const dir = tu_edpt_dir(p_endpoint_desc->bEndpointAddress); + + xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, dir); + xfer->max_size = tu_edpt_packet_size(p_endpoint_desc); + xfer->interval = p_endpoint_desc->bInterval; + + if (dir == TUSB_DIR_OUT) { + dwc2->epout[epnum].doepctl |= (1 << DOEPCTL_USBAEP_Pos) | + (p_endpoint_desc->bmAttributes.xfer << DOEPCTL_EPTYP_Pos) | + (p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DOEPCTL_SD0PID_SEVNFRM : 0) | + (xfer->max_size << DOEPCTL_MPSIZ_Pos); + + dwc2->daintmsk |= TU_BIT(DAINTMSK_OEPM_Pos + epnum); + } else + { + dwc2->epin[epnum].diepctl |= (1 << DIEPCTL_USBAEP_Pos) | + (epnum << DIEPCTL_TXFNUM_Pos) | + (p_endpoint_desc->bmAttributes.xfer << DIEPCTL_EPTYP_Pos) | + (p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DIEPCTL_SD0PID_SEVNFRM : 0) | + (xfer->max_size << DIEPCTL_MPSIZ_Pos); + + dwc2->daintmsk |= (1 << (DAINTMSK_IEPM_Pos + epnum)); + } + + return true; +} + bool dcd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t* buffer, uint16_t total_bytes) { uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); -- cgit v1.3.1 From 4116a962a6c3073e6c617797e3d87643eafc4375 Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Thu, 23 Nov 2023 19:20:03 +0100 Subject: Flush FIFO on bus reset. --- src/portable/synopsys/dwc2/dcd_dwc2.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index b0149a9a9..a411b54f4 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -139,6 +139,14 @@ static void bus_reset(uint8_t rhport) { dwc2->epout[n].doepctl |= DOEPCTL_SNAK; } + // flush all TX fifo and wait for it cleared + dwc2->grstctl = GRSTCTL_TXFFLSH | (0x10u << GRSTCTL_TXFNUM_Pos); + while (dwc2->grstctl & GRSTCTL_TXFFLSH_Msk) {} + + // flush RX fifo and wait for it cleared + dwc2->grstctl = GRSTCTL_RXFFLSH; + while (dwc2->grstctl & GRSTCTL_RXFFLSH_Msk) {} + // 2. Set up interrupt mask dwc2->daintmsk = TU_BIT(DAINTMSK_OEPM_Pos) | TU_BIT(DAINTMSK_IEPM_Pos); dwc2->doepmsk = DOEPMSK_STUPM | DOEPMSK_XFRCM; -- cgit v1.3.1 From 8055bc88d8f606c1f69d669a1c022d1a7bca44a2 Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Fri, 12 Jan 2024 15:59:51 +0100 Subject: Code refactor. --- src/portable/synopsys/dwc2/dcd_dwc2.c | 375 ++++++++++++++-------------------- 1 file changed, 157 insertions(+), 218 deletions(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index a411b54f4..f302b29b3 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -121,6 +121,155 @@ static void update_grxfsiz(uint8_t rhport) { dwc2->grxfsiz = calc_grxfsiz(max_epsize, ep_count); } +static bool fifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) +{ + dwc2_regs_t* dwc2 = DWC2_REG(rhport); + uint8_t const ep_count = _dwc2_controller[rhport].ep_count; + + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); + + TU_ASSERT(epnum < ep_count); + + uint16_t const fifo_size = tu_div_ceil(packet_size, 4); + + if (dir == TUSB_DIR_OUT) { + // Calculate required size of RX FIFO + uint16_t const sz = calc_grxfsiz(4 * fifo_size, ep_count); + + // If size_rx needs to be extended check if possible and if so enlarge it + if (dwc2->grxfsiz < sz) { + TU_ASSERT(sz + _allocated_fifo_words_tx <= _dwc2_controller[rhport].ep_fifo_size / 4); + + // Enlarge RX FIFO + dwc2->grxfsiz = sz; + } + + } else + { + // "USB Data FIFOs" section in reference manual + // Peripheral FIFO architecture + // + // --------------- 320 or 1024 ( 1280 or 4096 bytes ) + // | IN FIFO 0 | + // --------------- (320 or 1024) - 16 + // | IN FIFO 1 | + // --------------- (320 or 1024) - 16 - x + // | . . . . | + // --------------- (320 or 1024) - 16 - x - y - ... - z + // | IN FIFO MAX | + // --------------- + // | FREE | + // --------------- GRXFSIZ + // | OUT FIFO | + // | ( Shared ) | + // --------------- 0 + // + // In FIFO is allocated by following rules: + // - IN EP 1 gets FIFO 1, IN EP "n" gets FIFO "n". + + // Check if free space is available + TU_ASSERT(_allocated_fifo_words_tx + fifo_size + dwc2->grxfsiz <= _dwc2_controller[rhport].ep_fifo_size / 4); + + _allocated_fifo_words_tx += fifo_size; + + TU_LOG(DWC2_DEBUG, " Allocated %u bytes at offset %lu", fifo_size * 4, + _dwc2_controller[rhport].ep_fifo_size - _allocated_fifo_words_tx * 4); + + // DIEPTXF starts at FIFO #1. + // Both TXFD and TXSA are in unit of 32-bit words. + dwc2->dieptxf[epnum - 1] = (fifo_size << DIEPTXF_INEPTXFD_Pos) | + (_dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx); + } + + return true; +} + +static void edpt_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) +{ + dwc2_regs_t* dwc2 = DWC2_REG(rhport); + + uint8_t const epnum = tu_edpt_number(p_endpoint_desc->bEndpointAddress); + uint8_t const dir = tu_edpt_dir(p_endpoint_desc->bEndpointAddress); + + xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, dir); + xfer->max_size = tu_edpt_packet_size(p_endpoint_desc); + xfer->interval = p_endpoint_desc->bInterval; + + if (dir == TUSB_DIR_OUT) { + dwc2->epout[epnum].doepctl |= (1 << DOEPCTL_USBAEP_Pos) | + (p_endpoint_desc->bmAttributes.xfer << DOEPCTL_EPTYP_Pos) | + (p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DOEPCTL_SD0PID_SEVNFRM : 0) | + (xfer->max_size << DOEPCTL_MPSIZ_Pos); + + dwc2->daintmsk |= TU_BIT(DAINTMSK_OEPM_Pos + epnum); + } else + { + dwc2->epin[epnum].diepctl |= (1 << DIEPCTL_USBAEP_Pos) | + (epnum << DIEPCTL_TXFNUM_Pos) | + (p_endpoint_desc->bmAttributes.xfer << DIEPCTL_EPTYP_Pos) | + (p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DIEPCTL_SD0PID_SEVNFRM : 0) | + (xfer->max_size << DIEPCTL_MPSIZ_Pos); + + dwc2->daintmsk |= (1 << (DAINTMSK_IEPM_Pos + epnum)); + } +} + +static void edpt_disable(uint8_t rhport, uint8_t ep_addr, bool stall) { + (void) rhport; + + dwc2_regs_t* dwc2 = DWC2_REG(rhport); + + uint8_t const epnum = tu_edpt_number(ep_addr); + uint8_t const dir = tu_edpt_dir(ep_addr); + + if (dir == TUSB_DIR_IN) { + dwc2_epin_t* epin = dwc2->epin; + + // Only disable currently enabled non-control endpoint + if ((epnum == 0) || !(epin[epnum].diepctl & DIEPCTL_EPENA)) { + epin[epnum].diepctl |= DIEPCTL_SNAK | (stall ? DIEPCTL_STALL : 0); + } else { + // Stop transmitting packets and NAK IN xfers. + epin[epnum].diepctl |= DIEPCTL_SNAK; + while ((epin[epnum].diepint & DIEPINT_INEPNE) == 0) {} + + // Disable the endpoint. + epin[epnum].diepctl |= DIEPCTL_EPDIS | (stall ? DIEPCTL_STALL : 0); + while ((epin[epnum].diepint & DIEPINT_EPDISD_Msk) == 0) {} + + epin[epnum].diepint = DIEPINT_EPDISD; + } + + // Flush the FIFO, and wait until we have confirmed it cleared. + dwc2->grstctl = ((epnum << GRSTCTL_TXFNUM_Pos) | GRSTCTL_TXFFLSH); + while ((dwc2->grstctl & GRSTCTL_TXFFLSH_Msk) != 0) {} + } else { + dwc2_epout_t* epout = dwc2->epout; + + // Only disable currently enabled non-control endpoint + if ((epnum == 0) || !(epout[epnum].doepctl & DOEPCTL_EPENA)) { + epout[epnum].doepctl |= stall ? DOEPCTL_STALL : 0; + } else { + // Asserting GONAK is required to STALL an OUT endpoint. + // Simpler to use polling here, we don't use the "B"OUTNAKEFF interrupt + // anyway, and it can't be cleared by user code. If this while loop never + // finishes, we have bigger problems than just the stack. + dwc2->dctl |= DCTL_SGONAK; + while ((dwc2->gintsts & GINTSTS_BOUTNAKEFF_Msk) == 0) {} + + // Ditto here- disable the endpoint. + epout[epnum].doepctl |= DOEPCTL_EPDIS | (stall ? DOEPCTL_STALL : 0); + while ((epout[epnum].doepint & DOEPINT_EPDISD_Msk) == 0) {} + + epout[epnum].doepint = DOEPINT_EPDISD; + + // Allow other OUT endpoints to keep receiving. + dwc2->dctl |= DCTL_CGONAK; + } + } +} + // Start of Bus Reset static void bus_reset(uint8_t rhport) { dwc2_regs_t* dwc2 = DWC2_REG(rhport); @@ -555,81 +704,9 @@ void dcd_sof_enable(uint8_t rhport, bool en) { bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const* desc_edpt) { (void) rhport; - dwc2_regs_t* dwc2 = DWC2_REG(rhport); - uint8_t const ep_count = _dwc2_controller[rhport].ep_count; + TU_ASSERT(fifo_alloc(rhport, desc_edpt->bEndpointAddress, tu_edpt_packet_size(desc_edpt))); - uint8_t const epnum = tu_edpt_number(desc_edpt->bEndpointAddress); - uint8_t const dir = tu_edpt_dir(desc_edpt->bEndpointAddress); - - TU_ASSERT(epnum < ep_count); - - xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, dir); - xfer->max_size = tu_edpt_packet_size(desc_edpt); - xfer->interval = desc_edpt->bInterval; - - uint16_t const fifo_size = tu_div_ceil(xfer->max_size, 4); - - if (dir == TUSB_DIR_OUT) { - // Calculate required size of RX FIFO - uint16_t const sz = calc_grxfsiz(4 * fifo_size, ep_count); - - // If size_rx needs to be extended check if possible and if so enlarge it - if (dwc2->grxfsiz < sz) { - TU_ASSERT(sz + _allocated_fifo_words_tx <= _dwc2_controller[rhport].ep_fifo_size / 4); - - // Enlarge RX FIFO - dwc2->grxfsiz = sz; - } - - dwc2->epout[epnum].doepctl |= (1 << DOEPCTL_USBAEP_Pos) | - (desc_edpt->bmAttributes.xfer << DOEPCTL_EPTYP_Pos) | - (desc_edpt->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DOEPCTL_SD0PID_SEVNFRM : 0) | - (xfer->max_size << DOEPCTL_MPSIZ_Pos); - - dwc2->daintmsk |= TU_BIT(DAINTMSK_OEPM_Pos + epnum); - } else { - // "USB Data FIFOs" section in reference manual - // Peripheral FIFO architecture - // - // --------------- 320 or 1024 ( 1280 or 4096 bytes ) - // | IN FIFO 0 | - // --------------- (320 or 1024) - 16 - // | IN FIFO 1 | - // --------------- (320 or 1024) - 16 - x - // | . . . . | - // --------------- (320 or 1024) - 16 - x - y - ... - z - // | IN FIFO MAX | - // --------------- - // | FREE | - // --------------- GRXFSIZ - // | OUT FIFO | - // | ( Shared ) | - // --------------- 0 - // - // In FIFO is allocated by following rules: - // - IN EP 1 gets FIFO 1, IN EP "n" gets FIFO "n". - - // Check if free space is available - TU_ASSERT(_allocated_fifo_words_tx + fifo_size + dwc2->grxfsiz <= _dwc2_controller[rhport].ep_fifo_size / 4); - - _allocated_fifo_words_tx += fifo_size; - - TU_LOG(DWC2_DEBUG, " Allocated %u bytes at offset %lu", fifo_size * 4, - _dwc2_controller[rhport].ep_fifo_size - _allocated_fifo_words_tx * 4); - - // DIEPTXF starts at FIFO #1. - // Both TXFD and TXSA are in unit of 32-bit words. - dwc2->dieptxf[epnum - 1] = (fifo_size << DIEPTXF_INEPTXFD_Pos) | - (_dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx); - - dwc2->epin[epnum].diepctl |= (1 << DIEPCTL_USBAEP_Pos) | - (epnum << DIEPCTL_TXFNUM_Pos) | - (desc_edpt->bmAttributes.xfer << DIEPCTL_EPTYP_Pos) | - (desc_edpt->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DIEPCTL_SD0PID_SEVNFRM : 0) | - (xfer->max_size << DIEPCTL_MPSIZ_Pos); - - dwc2->daintmsk |= (1 << (DAINTMSK_IEPM_Pos + epnum)); - } + edpt_activate(rhport, desc_edpt); return true; } @@ -658,102 +735,17 @@ void dcd_edpt_close_all(uint8_t rhport) { bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { - (void)rhport; - - TU_ASSERT(largest_packet_size <= 1024); - - dwc2_regs_t* dwc2 = DWC2_REG(rhport); - uint8_t const ep_count = _dwc2_controller[rhport].ep_count; - - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - TU_ASSERT(epnum < ep_count); - - uint16_t const fifo_size = tu_div_ceil(largest_packet_size, 4); - - if (dir == TUSB_DIR_OUT) { - // Calculate required size of RX FIFO - uint16_t const sz = calc_grxfsiz(4 * fifo_size, ep_count); - - // If size_rx needs to be extended check if possible and if so enlarge it - if (dwc2->grxfsiz < sz) { - TU_ASSERT(sz + _allocated_fifo_words_tx <= _dwc2_controller[rhport].ep_fifo_size / 4); - - // Enlarge RX FIFO - dwc2->grxfsiz = sz; - } - - } else - { - // "USB Data FIFOs" section in reference manual - // Peripheral FIFO architecture - // - // --------------- 320 or 1024 ( 1280 or 4096 bytes ) - // | IN FIFO 0 | - // --------------- (320 or 1024) - 16 - // | IN FIFO 1 | - // --------------- (320 or 1024) - 16 - x - // | . . . . | - // --------------- (320 or 1024) - 16 - x - y - ... - z - // | IN FIFO MAX | - // --------------- - // | FREE | - // --------------- GRXFSIZ - // | OUT FIFO | - // | ( Shared ) | - // --------------- 0 - // - // In FIFO is allocated by following rules: - // - IN EP 1 gets FIFO 1, IN EP "n" gets FIFO "n". - - // Check if free space is available - TU_ASSERT(_allocated_fifo_words_tx + fifo_size + dwc2->grxfsiz <= _dwc2_controller[rhport].ep_fifo_size / 4); - - _allocated_fifo_words_tx += fifo_size; - - TU_LOG(DWC2_DEBUG, " Allocated %u bytes at offset %lu", fifo_size * 4, - _dwc2_controller[rhport].ep_fifo_size - _allocated_fifo_words_tx * 4); - - // DIEPTXF starts at FIFO #1. - // Both TXFD and TXSA are in unit of 32-bit words. - dwc2->dieptxf[epnum - 1] = (fifo_size << DIEPTXF_INEPTXFD_Pos) | - (_dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx); - } + TU_ASSERT(fifo_alloc(rhport, ep_addr, largest_packet_size)); return true; } bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) { - (void)rhport; - - dwc2_regs_t* dwc2 = DWC2_REG(rhport); - - uint8_t const epnum = tu_edpt_number(p_endpoint_desc->bEndpointAddress); - uint8_t const dir = tu_edpt_dir(p_endpoint_desc->bEndpointAddress); - - xfer_ctl_t* xfer = XFER_CTL_BASE(epnum, dir); - xfer->max_size = tu_edpt_packet_size(p_endpoint_desc); - xfer->interval = p_endpoint_desc->bInterval; + // Disable EP to clear potential incomplete transfers + edpt_disable(rhport, p_endpoint_desc->bEndpointAddress, false); - if (dir == TUSB_DIR_OUT) { - dwc2->epout[epnum].doepctl |= (1 << DOEPCTL_USBAEP_Pos) | - (p_endpoint_desc->bmAttributes.xfer << DOEPCTL_EPTYP_Pos) | - (p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DOEPCTL_SD0PID_SEVNFRM : 0) | - (xfer->max_size << DOEPCTL_MPSIZ_Pos); - - dwc2->daintmsk |= TU_BIT(DAINTMSK_OEPM_Pos + epnum); - } else - { - dwc2->epin[epnum].diepctl |= (1 << DIEPCTL_USBAEP_Pos) | - (epnum << DIEPCTL_TXFNUM_Pos) | - (p_endpoint_desc->bmAttributes.xfer << DIEPCTL_EPTYP_Pos) | - (p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DIEPCTL_SD0PID_SEVNFRM : 0) | - (xfer->max_size << DIEPCTL_MPSIZ_Pos); - - dwc2->daintmsk |= (1 << (DAINTMSK_IEPM_Pos + epnum)); - } + edpt_activate(rhport, p_endpoint_desc); return true; } @@ -815,60 +807,7 @@ bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t* ff, uint16_t return true; } -static void dcd_edpt_disable(uint8_t rhport, uint8_t ep_addr, bool stall) { - (void) rhport; - - dwc2_regs_t* dwc2 = DWC2_REG(rhport); - - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - - if (dir == TUSB_DIR_IN) { - dwc2_epin_t* epin = dwc2->epin; - - // Only disable currently enabled non-control endpoint - if ((epnum == 0) || !(epin[epnum].diepctl & DIEPCTL_EPENA)) { - epin[epnum].diepctl |= DIEPCTL_SNAK | (stall ? DIEPCTL_STALL : 0); - } else { - // Stop transmitting packets and NAK IN xfers. - epin[epnum].diepctl |= DIEPCTL_SNAK; - while ((epin[epnum].diepint & DIEPINT_INEPNE) == 0) {} - - // Disable the endpoint. - epin[epnum].diepctl |= DIEPCTL_EPDIS | (stall ? DIEPCTL_STALL : 0); - while ((epin[epnum].diepint & DIEPINT_EPDISD_Msk) == 0) {} - - epin[epnum].diepint = DIEPINT_EPDISD; - } - // Flush the FIFO, and wait until we have confirmed it cleared. - dwc2->grstctl = ((epnum << GRSTCTL_TXFNUM_Pos) | GRSTCTL_TXFFLSH); - while ((dwc2->grstctl & GRSTCTL_TXFFLSH_Msk) != 0) {} - } else { - dwc2_epout_t* epout = dwc2->epout; - - // Only disable currently enabled non-control endpoint - if ((epnum == 0) || !(epout[epnum].doepctl & DOEPCTL_EPENA)) { - epout[epnum].doepctl |= stall ? DOEPCTL_STALL : 0; - } else { - // Asserting GONAK is required to STALL an OUT endpoint. - // Simpler to use polling here, we don't use the "B"OUTNAKEFF interrupt - // anyway, and it can't be cleared by user code. If this while loop never - // finishes, we have bigger problems than just the stack. - dwc2->dctl |= DCTL_SGONAK; - while ((dwc2->gintsts & GINTSTS_BOUTNAKEFF_Msk) == 0) {} - - // Ditto here- disable the endpoint. - epout[epnum].doepctl |= DOEPCTL_EPDIS | (stall ? DOEPCTL_STALL : 0); - while ((epout[epnum].doepint & DOEPINT_EPDISD_Msk) == 0) {} - - epout[epnum].doepint = DOEPINT_EPDISD; - - // Allow other OUT endpoints to keep receiving. - dwc2->dctl |= DCTL_CGONAK; - } - } -} /** * Close an endpoint. @@ -879,7 +818,7 @@ void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) { uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); - dcd_edpt_disable(rhport, ep_addr, false); + edpt_disable(rhport, ep_addr, false); // Update max_size xfer_status[epnum][dir].max_size = 0; // max_size = 0 marks a disabled EP - required for changing FIFO allocation @@ -897,7 +836,7 @@ void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) { } void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { - dcd_edpt_disable(rhport, ep_addr, true); + edpt_disable(rhport, ep_addr, true); } void dcd_edpt_clear_stall(uint8_t rhport, uint8_t ep_addr) { -- cgit v1.3.1 From 85420c61c780e260d0afd21de4a39c17ceba5d87 Mon Sep 17 00:00:00 2001 From: hathach Date: Sun, 31 Mar 2024 13:49:41 +0700 Subject: minor clean up --- src/portable/synopsys/dwc2/dcd_dwc2.c | 104 ++++++++++++++-------------------- 1 file changed, 41 insertions(+), 63 deletions(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index f302b29b3..cf8f3be50 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -102,7 +102,13 @@ static bool _out_ep_closed; // Flag to check if RX FIFO size n // SOF enabling flag - required for SOF to not get disabled in ISR when SOF was enabled by static bool _sof_en; -// Calculate the RX FIFO size according to recommendations from reference manual +// Calculate the RX FIFO size according to minimum recommendations from reference manual +// RxFIFO = (5 * number of control endpoints + 8) + +// ((largest USB packet used / 4) + 1 for status information) + +// (2 * number of OUT endpoints) + 1 for Global NAK +// with number of control endpoints = 1 we have +// RxFIFO = 15 + (largest USB packet used / 4) + 2 * number of OUT endpoints +// we double the largest USB packet size to be able to hold up to 2 packets static inline uint16_t calc_grxfsiz(uint16_t max_ep_size, uint8_t ep_count) { return 15 + 2 * (max_ep_size / 4) + 2 * ep_count; } @@ -121,11 +127,9 @@ static void update_grxfsiz(uint8_t rhport) { dwc2->grxfsiz = calc_grxfsiz(max_epsize, ep_count); } -static bool fifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) -{ +static bool fifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) { dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const ep_count = _dwc2_controller[rhport].ep_count; - uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); @@ -133,6 +137,26 @@ static bool fifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) uint16_t const fifo_size = tu_div_ceil(packet_size, 4); + // "USB Data FIFOs" section in reference manual + // Peripheral FIFO architecture + // + // --------------- 320 or 1024 ( 1280 or 4096 bytes ) + // | IN FIFO 0 | + // --------------- (320 or 1024) - 16 + // | IN FIFO 1 | + // --------------- (320 or 1024) - 16 - x + // | . . . . | + // --------------- (320 or 1024) - 16 - x - y - ... - z + // | IN FIFO MAX | + // --------------- + // | FREE | + // --------------- GRXFSIZ + // | OUT FIFO | + // | ( Shared ) | + // --------------- 0 + // + // In FIFO is allocated by following rules: + // - IN EP 1 gets FIFO 1, IN EP "n" gets FIFO "n". if (dir == TUSB_DIR_OUT) { // Calculate required size of RX FIFO uint16_t const sz = calc_grxfsiz(4 * fifo_size, ep_count); @@ -144,35 +168,10 @@ static bool fifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) // Enlarge RX FIFO dwc2->grxfsiz = sz; } - - } else - { - // "USB Data FIFOs" section in reference manual - // Peripheral FIFO architecture - // - // --------------- 320 or 1024 ( 1280 or 4096 bytes ) - // | IN FIFO 0 | - // --------------- (320 or 1024) - 16 - // | IN FIFO 1 | - // --------------- (320 or 1024) - 16 - x - // | . . . . | - // --------------- (320 or 1024) - 16 - x - y - ... - z - // | IN FIFO MAX | - // --------------- - // | FREE | - // --------------- GRXFSIZ - // | OUT FIFO | - // | ( Shared ) | - // --------------- 0 - // - // In FIFO is allocated by following rules: - // - IN EP 1 gets FIFO 1, IN EP "n" gets FIFO "n". - + } else { // Check if free space is available TU_ASSERT(_allocated_fifo_words_tx + fifo_size + dwc2->grxfsiz <= _dwc2_controller[rhport].ep_fifo_size / 4); - _allocated_fifo_words_tx += fifo_size; - TU_LOG(DWC2_DEBUG, " Allocated %u bytes at offset %lu", fifo_size * 4, _dwc2_controller[rhport].ep_fifo_size - _allocated_fifo_words_tx * 4); @@ -185,10 +184,8 @@ static bool fifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) return true; } -static void edpt_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) -{ +static void edpt_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) { dwc2_regs_t* dwc2 = DWC2_REG(rhport); - uint8_t const epnum = tu_edpt_number(p_endpoint_desc->bEndpointAddress); uint8_t const dir = tu_edpt_dir(p_endpoint_desc->bEndpointAddress); @@ -196,21 +193,17 @@ static void edpt_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoi xfer->max_size = tu_edpt_packet_size(p_endpoint_desc); xfer->interval = p_endpoint_desc->bInterval; - if (dir == TUSB_DIR_OUT) { - dwc2->epout[epnum].doepctl |= (1 << DOEPCTL_USBAEP_Pos) | - (p_endpoint_desc->bmAttributes.xfer << DOEPCTL_EPTYP_Pos) | - (p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DOEPCTL_SD0PID_SEVNFRM : 0) | - (xfer->max_size << DOEPCTL_MPSIZ_Pos); + // USBAEP, EPTYP, SD0PID_SEVNFRM, MPSIZ are the same for IN and OUT endpoints. + uint32_t const dxepctl = (1 << DOEPCTL_USBAEP_Pos) | + (p_endpoint_desc->bmAttributes.xfer << DOEPCTL_EPTYP_Pos) | + (p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DOEPCTL_SD0PID_SEVNFRM : 0) | + (xfer->max_size << DOEPCTL_MPSIZ_Pos); + if (dir == TUSB_DIR_OUT) { + dwc2->epout[epnum].doepctl |= dxepctl; dwc2->daintmsk |= TU_BIT(DAINTMSK_OEPM_Pos + epnum); - } else - { - dwc2->epin[epnum].diepctl |= (1 << DIEPCTL_USBAEP_Pos) | - (epnum << DIEPCTL_TXFNUM_Pos) | - (p_endpoint_desc->bmAttributes.xfer << DIEPCTL_EPTYP_Pos) | - (p_endpoint_desc->bmAttributes.xfer != TUSB_XFER_ISOCHRONOUS ? DIEPCTL_SD0PID_SEVNFRM : 0) | - (xfer->max_size << DIEPCTL_MPSIZ_Pos); - + } else { + dwc2->epin[epnum].diepctl |= dxepctl | (epnum << DIEPCTL_TXFNUM_Pos); dwc2->daintmsk |= (1 << (DAINTMSK_IEPM_Pos + epnum)); } } @@ -219,7 +212,6 @@ static void edpt_disable(uint8_t rhport, uint8_t ep_addr, bool stall) { (void) rhport; dwc2_regs_t* dwc2 = DWC2_REG(rhport); - uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); @@ -426,7 +418,6 @@ static void edpt_schedule_packets(uint8_t rhport, uint8_t const epnum, uint8_t c /* Controller API *------------------------------------------------------------------*/ #if CFG_TUSB_DEBUG >= DWC2_DEBUG - void print_dwc2_info(dwc2_regs_t* dwc2) { // print guid, gsnpsid, ghwcfg1, ghwcfg2, ghwcfg3, ghwcfg4 // use dwc2_info.py/md for bit-field value and comparison with other ports @@ -437,7 +428,6 @@ void print_dwc2_info(dwc2_regs_t* dwc2) { } TU_LOG(DWC2_DEBUG, "0x%08lX\r\n", p[5]); } - #endif static void reset_core(dwc2_regs_t* dwc2) { @@ -702,12 +692,8 @@ void dcd_sof_enable(uint8_t rhport, bool en) { *------------------------------------------------------------------*/ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const* desc_edpt) { - (void) rhport; - TU_ASSERT(fifo_alloc(rhport, desc_edpt->bEndpointAddress, tu_edpt_packet_size(desc_edpt))); - edpt_activate(rhport, desc_edpt); - return true; } @@ -733,15 +719,12 @@ void dcd_edpt_close_all(uint8_t rhport) { _allocated_fifo_words_tx = 16; } -bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) -{ +bool dcd_edpt_iso_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t largest_packet_size) { TU_ASSERT(fifo_alloc(rhport, ep_addr, largest_packet_size)); - return true; } -bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) -{ +bool dcd_edpt_iso_activate(uint8_t rhport, tusb_desc_endpoint_t const * p_endpoint_desc) { // Disable EP to clear potential incomplete transfers edpt_disable(rhport, p_endpoint_desc->bEndpointAddress, false); @@ -807,11 +790,6 @@ bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t* ff, uint16_t return true; } - - -/** - * Close an endpoint. - */ void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) { dwc2_regs_t* dwc2 = DWC2_REG(rhport); -- cgit v1.3.1 From 998090d1a7f914c04f0bb3e6ac85634d432d88fc Mon Sep 17 00:00:00 2001 From: IngHK Date: Fri, 29 Mar 2024 15:59:11 +0100 Subject: added further debug log outputs --- src/portable/analog/max3421/hcd_max3421.c | 32 ++++++++++++++++++++++++++++--- 1 file changed, 29 insertions(+), 3 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index d366298ea..93d12fc64 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -29,6 +29,7 @@ #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 #define NAK_RETRY_HANDLING 1 +#define PUTCHAR_LOGS 0 // TODO to be deleted later #include #include "host/hcd.h" @@ -808,7 +809,11 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { xfer_result_t xfer_result; switch(hresult) { case HRSL_SUCCESS: -// putchar('S'); +#if PUTCHAR_LOGS // TODO to be deleted later + putchar(ep->ep_dir ? 's' : 'S'); + putchar('0' + ep->daddr); +// putchar('0' + ep->ep_num); +#endif xfer_result = XFER_RESULT_SUCCESS; break; @@ -817,7 +822,12 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { break; case HRSL_NAK: -// putchar('N'); +#if PUTCHAR_LOGS // TODO to be deleted later + putchar(ep->ep_dir ? 'n' : 'N'); + putchar('0' + ep->daddr); +// putchar('0' + ep->ep_num); +// putchar('0' + ep->xfer_attemp); +#endif #if NAK_RETRY_HANDLING ep->retry_pending = 1; ep->xfer_pending = 0; @@ -928,6 +938,12 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { // print_hirq(hirq); if (hirq & HIRQ_FRAME_IRQ) { + LL_GPIO_SetOutputPin ( D2_GPIO_Port, D2_Pin ); // TODO to be deleted later +#if PUTCHAR_LOGS // TODO to be deleted later + putchar(13); + putchar(10); + putchar('F'); +#endif _hcd_data.frame_count++; #if NAK_RETRY_HANDLING @@ -937,7 +953,11 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { max3421_ep_t * ep = &_hcd_data.ep[i]; // set retryable EPs to pending if (ep->retry_pending) { -// putchar('R'); +#if PUTCHAR_LOGS // TODO to be deleted later + putchar(ep->ep_dir ? 'r' : 'R'); + putchar('0' + ep->daddr); +// putchar('0' + ep->ep_num); +#endif ep->xfer_pending = 1; ep->retry_pending = 0; if (next_ep == NULL) { @@ -948,10 +968,16 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { // trigger 1st retryable EP if (next_ep) { if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { +#if PUTCHAR_LOGS // TODO to be deleted later + putchar(next_ep->ep_dir ? 't' : 'T'); + putchar('0' + next_ep->daddr); +// putchar('0' + next_ep->ep_num); +#endif xact_inout(rhport, next_ep, true, in_isr); } } #endif + LL_GPIO_SetOutputPin ( D2_GPIO_Port, D2_Pin << 16 ); } if (hirq & HIRQ_CONDET_IRQ) { -- cgit v1.3.1 From 818c64efecfb70d8abfee6b90d53f4af8c452dcf Mon Sep 17 00:00:00 2001 From: IngHK Date: Sat, 30 Mar 2024 14:11:02 +0100 Subject: fixed EP0 control handling --- src/portable/analog/max3421/hcd_max3421.c | 32 +++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 93d12fc64..9209865d4 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -828,36 +828,36 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { // putchar('0' + ep->ep_num); // putchar('0' + ep->xfer_attemp); #endif -#if NAK_RETRY_HANDLING - ep->retry_pending = 1; - ep->xfer_pending = 0; - max3421_ep_t * next_ep = find_next_pending_ep(ep); - if (next_ep) { - // switch to next pending TODO could have issue with double buffered if not clear previously out data - xact_inout(rhport, next_ep, true, in_isr); - } else { - // no more pending - atomic_flag_clear(&_hcd_data.busy); - } -#else if (ep_num == 0) { // NAK on control, retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); - }else { + } else { + #if NAK_RETRY_HANDLING + ep->retry_pending = 1; + ep->xfer_pending = 0; + max3421_ep_t * next_ep = find_next_pending_ep(ep); + if (next_ep) { + // switch to next pending TODO could have issue with double buffered if not clear previously out data + xact_inout(rhport, next_ep, true, in_isr); + } else { + // no more pending + atomic_flag_clear(&_hcd_data.busy); + } + #else // NAK on non-control, find next pending to switch max3421_ep_t *next_ep = find_next_pending_ep(ep); if (ep == next_ep) { // this endpoint is only one pending, retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); - }else if (next_ep) { + } else if (next_ep) { // switch to next pending TODO could have issue with double buffered if not clear previously out data xact_inout(rhport, next_ep, true, in_isr); - }else { + } else { TU_ASSERT(false,); } + #endif } -#endif return; case HRSL_BAD_REQ: -- cgit v1.3.1 From 11a54bc8e185c58fa5c72b6913ac07e3a3060be6 Mon Sep 17 00:00:00 2001 From: IngHK Date: Sat, 30 Mar 2024 14:16:13 +0100 Subject: renamed define NAK_RETRY_HANDLING to CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME as official option --- src/portable/analog/max3421/hcd_max3421.c | 9 +++++---- src/tusb_option.h | 9 +++++++++ 2 files changed, 14 insertions(+), 4 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 9209865d4..09de1bc5a 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -28,7 +28,6 @@ #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 -#define NAK_RETRY_HANDLING 1 #define PUTCHAR_LOGS 0 // TODO to be deleted later #include @@ -169,6 +168,8 @@ enum { DEFAULT_HIEN = HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ | HIRQ_HXFRDN_IRQ | HIRQ_RCVDAV_IRQ }; +TU_VERIFY_STATIC(CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME >= 0 && CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME <= 1, "unsupported attemp quantity"); + //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ @@ -183,7 +184,7 @@ typedef struct { uint8_t data_toggle : 1; uint8_t xfer_pending : 1; uint8_t xfer_complete : 1; -#if NAK_RETRY_HANDLING +#if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME uint8_t retry_pending : 1; #endif }; @@ -832,7 +833,7 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { // NAK on control, retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); } else { - #if NAK_RETRY_HANDLING + #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME ep->retry_pending = 1; ep->xfer_pending = 0; max3421_ep_t * next_ep = find_next_pending_ep(ep); @@ -946,7 +947,7 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { #endif _hcd_data.frame_count++; -#if NAK_RETRY_HANDLING +#if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME // retry EPs max3421_ep_t * next_ep = NULL; for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { diff --git a/src/tusb_option.h b/src/tusb_option.h index 22f27e9e1..68eb4882c 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -529,6 +529,15 @@ #define CFG_TUH_MAX3421 0 #endif +// MAX3421 Host max. transfer attemps per frame (except control and iso) +// temporary only one attemp (no retry) per frame allowed (more in work) +// retry quantity = (CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - 1) +// 0 = endless retries in current frame. is default to keep compatibility +#ifndef CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME + #define CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME 0 +#endif + + //--------------------------------------------------------------------+ // TypeC Options (Default) //--------------------------------------------------------------------+ -- cgit v1.3.1 From 009d85722bbfae41f057cfbb69c63716a5fb2c5f Mon Sep 17 00:00:00 2001 From: IngHK Date: Sat, 30 Mar 2024 15:17:34 +0100 Subject: replaced bits xfer_pending, xfer_complete and retry_pending by common 4 bits state --- src/portable/analog/max3421/hcd_max3421.c | 47 ++++++++++++++++--------------- 1 file changed, 24 insertions(+), 23 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 09de1bc5a..2b3c625dc 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -168,6 +168,15 @@ enum { DEFAULT_HIEN = HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ | HIRQ_HXFRDN_IRQ | HIRQ_RCVDAV_IRQ }; +enum { + EP_STATE_IDLE = 0, + EP_STATE_PENDING, +#if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME + EP_STATE_SUSPENDED, +#endif + EP_STATE_COMPLETE +}; + TU_VERIFY_STATIC(CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME >= 0 && CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME <= 1, "unsupported attemp quantity"); //--------------------------------------------------------------------+ @@ -178,15 +187,11 @@ typedef struct { uint8_t daddr; struct TU_ATTR_PACKED { - uint8_t ep_dir : 1; - uint8_t is_iso : 1; - uint8_t is_setup : 1; + uint8_t state : 4; + uint8_t is_setup : 1; // also bit 4 in HXFR reg (smaller code, no shift necessary) + uint8_t ep_dir : 1; // also bit 5 in HXFR reg (smaller code, no shift necessary) + uint8_t is_iso : 1; // also bit 6 in HXFR reg (smaller code, no shift necessary) uint8_t data_toggle : 1; - uint8_t xfer_pending : 1; - uint8_t xfer_complete : 1; -#if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - uint8_t retry_pending : 1; -#endif }; struct TU_ATTR_PACKED { @@ -406,7 +411,7 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // starting from next endpoint for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->xfer_pending && ep->packet_size) { + if (ep->state == EP_STATE_PENDING && ep->packet_size) { // TU_LOG3("next pending i = %u\r\n", i); return ep; } @@ -415,7 +420,7 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // wrap around including current endpoint for (size_t i = 0; i <= idx; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->xfer_pending && ep->packet_size) { + if (ep->state == EP_STATE_PENDING && ep->packet_size) { // TU_LOG3("next pending i = %u\r\n", i); return ep; } @@ -664,8 +669,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->buf = buffer; ep->total_len = buflen; ep->xferred_len = 0; - ep->xfer_complete = 0; - ep->xfer_pending = 1; + ep->state = EP_STATE_PENDING; if ( ep_num == 0 ) { ep->is_setup = 0; @@ -704,8 +708,7 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] ep->buf = (uint8_t*)(uintptr_t) setup_packet; ep->total_len = 8; ep->xferred_len = 0; - ep->xfer_complete = 0; - ep->xfer_pending = 1; + ep->state = EP_STATE_PENDING; // carry out transfer if not busy if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { @@ -783,7 +786,7 @@ static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t re ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1u : 0u; } - ep->xfer_pending = 0; + ep->state = EP_STATE_IDLE; hcd_event_xfer_complete(ep->daddr, ep_addr, ep->xferred_len, result, in_isr); // Find next pending endpoint @@ -834,8 +837,7 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { hxfr_write(rhport, _hcd_data.hxfr, in_isr); } else { #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - ep->retry_pending = 1; - ep->xfer_pending = 0; + ep->state = EP_STATE_SUSPENDED; max3421_ep_t * next_ep = find_next_pending_ep(ep); if (next_ep) { // switch to next pending TODO could have issue with double buffered if not clear previously out data @@ -879,11 +881,11 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { if (ep_dir) { // IN transfer: fifo data is already received in RCVDAV IRQ if ( hxfr_type & HXFR_HS ) { - ep->xfer_complete = 1; + ep->state = EP_STATE_COMPLETE; } // short packet or all bytes transferred - if ( ep->xfer_complete ) { + if (ep->state == EP_STATE_COMPLETE) { xfer_complete_isr(rhport, ep, xfer_result, hrsl, in_isr); }else { // more to transfer @@ -953,14 +955,13 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t * ep = &_hcd_data.ep[i]; // set retryable EPs to pending - if (ep->retry_pending) { + if (ep->state == EP_STATE_SUSPENDED) { #if PUTCHAR_LOGS // TODO to be deleted later putchar(ep->ep_dir ? 'r' : 'R'); putchar('0' + ep->daddr); // putchar('0' + ep->ep_num); #endif - ep->xfer_pending = 1; - ep->retry_pending = 0; + ep->state = EP_STATE_PENDING; if (next_ep == NULL) { next_ep = &_hcd_data.ep[i]; } @@ -1009,7 +1010,7 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { } if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { - ep->xfer_complete = 1; + ep->state = EP_STATE_COMPLETE; } } -- cgit v1.3.1 From 0bb26c97c316cbf3dc0b6e70234c958cf361da73 Mon Sep 17 00:00:00 2001 From: IngHK Date: Sat, 30 Mar 2024 14:49:00 +0100 Subject: removed redundant return true; --- src/portable/analog/max3421/hcd_max3421.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 2b3c625dc..335d78481 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -679,8 +679,6 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf // carry out transfer if not busy if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { xact_inout(rhport, ep, true, false); - } else { - return true; } return true; -- cgit v1.3.1 From f3fccaad2657fae7957523aee5ec1698b55470c4 Mon Sep 17 00:00:00 2001 From: IngHK Date: Sat, 30 Mar 2024 14:57:22 +0100 Subject: improved/fixed trigger 1st retryable EP --- src/portable/analog/max3421/hcd_max3421.c | 22 +++++++++------------- 1 file changed, 9 insertions(+), 13 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 335d78481..2dc8f2e18 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -949,7 +949,6 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME // retry EPs - max3421_ep_t * next_ep = NULL; for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t * ep = &_hcd_data.ep[i]; // set retryable EPs to pending @@ -960,20 +959,17 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { // putchar('0' + ep->ep_num); #endif ep->state = EP_STATE_PENDING; - if (next_ep == NULL) { - next_ep = &_hcd_data.ep[i]; - } - } - } - // trigger 1st retryable EP - if (next_ep) { - if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { + // trigger 1st retryable EP + if (ep->packet_size) { // first test packet_size before atomic_flag_test_and_set() + if (!atomic_flag_test_and_set(&_hcd_data.busy) ) { #if PUTCHAR_LOGS // TODO to be deleted later - putchar(next_ep->ep_dir ? 't' : 'T'); - putchar('0' + next_ep->daddr); -// putchar('0' + next_ep->ep_num); + putchar(ep->ep_dir ? 't' : 'T'); + putchar('0' + ep->daddr); +// putchar('0' + ep->ep_num); #endif - xact_inout(rhport, next_ep, true, in_isr); + xact_inout(rhport, ep, true, in_isr); + } + } } } #endif -- cgit v1.3.1 From 79bc09a68ce07224983bf597b29e7fb1084617f3 Mon Sep 17 00:00:00 2001 From: IngHK Date: Sat, 30 Mar 2024 15:15:05 +0100 Subject: improved code readability --- src/portable/analog/max3421/hcd_max3421.c | 75 +++++++++++++++---------------- 1 file changed, 35 insertions(+), 40 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 2dc8f2e18..dbdd2d127 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -788,7 +788,7 @@ static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t re hcd_event_xfer_complete(ep->daddr, ep_addr, ep->xferred_len, result, in_isr); // Find next pending endpoint - max3421_ep_t *next_ep = find_next_pending_ep(ep); + max3421_ep_t * next_ep = find_next_pending_ep(ep); if (next_ep) { xact_inout(rhport, next_ep, true, in_isr); }else { @@ -811,11 +811,11 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { xfer_result_t xfer_result; switch(hresult) { case HRSL_SUCCESS: -#if PUTCHAR_LOGS // TODO to be deleted later - putchar(ep->ep_dir ? 's' : 'S'); - putchar('0' + ep->daddr); -// putchar('0' + ep->ep_num); -#endif + #if PUTCHAR_LOGS // TODO to be deleted later + putchar(ep->ep_dir ? 's' : 'S'); + putchar('0' + ep->daddr); +// putchar('0' + ep->ep_num); + #endif xfer_result = XFER_RESULT_SUCCESS; break; @@ -824,12 +824,12 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { break; case HRSL_NAK: -#if PUTCHAR_LOGS // TODO to be deleted later - putchar(ep->ep_dir ? 'n' : 'N'); - putchar('0' + ep->daddr); -// putchar('0' + ep->ep_num); -// putchar('0' + ep->xfer_attemp); -#endif + #if PUTCHAR_LOGS // TODO to be deleted later + putchar(ep->ep_dir ? 'n' : 'N'); + putchar('0' + ep->daddr); +// putchar('0' + ep->ep_num); + putchar('0' + ep->state); + #endif if (ep_num == 0) { // NAK on control, retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); @@ -917,13 +917,13 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { void print_hirq(uint8_t hirq) { TU_LOG3_HEX(hirq); - if (hirq & HIRQ_HXFRDN_IRQ) TU_LOG3(" HXFRDN"); - if (hirq & HIRQ_FRAME_IRQ) TU_LOG3(" FRAME"); - if (hirq & HIRQ_CONDET_IRQ) TU_LOG3(" CONDET"); - if (hirq & HIRQ_SUSDN_IRQ) TU_LOG3(" SUSDN"); - if (hirq & HIRQ_SNDBAV_IRQ) TU_LOG3(" SNDBAV"); - if (hirq & HIRQ_RCVDAV_IRQ) TU_LOG3(" RCVDAV"); - if (hirq & HIRQ_RWU_IRQ) TU_LOG3(" RWU"); + if (hirq & HIRQ_HXFRDN_IRQ) TU_LOG3(" HXFRDN"); + if (hirq & HIRQ_FRAME_IRQ) TU_LOG3(" FRAME"); + if (hirq & HIRQ_CONDET_IRQ) TU_LOG3(" CONDET"); + if (hirq & HIRQ_SUSDN_IRQ) TU_LOG3(" SUSDN"); + if (hirq & HIRQ_SNDBAV_IRQ) TU_LOG3(" SNDBAV"); + if (hirq & HIRQ_RCVDAV_IRQ) TU_LOG3(" RCVDAV"); + if (hirq & HIRQ_RWU_IRQ) TU_LOG3(" RWU"); if (hirq & HIRQ_BUSEVENT_IRQ) TU_LOG3(" BUSEVENT"); TU_LOG3("\r\n"); @@ -940,33 +940,28 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { if (hirq & HIRQ_FRAME_IRQ) { LL_GPIO_SetOutputPin ( D2_GPIO_Port, D2_Pin ); // TODO to be deleted later -#if PUTCHAR_LOGS // TODO to be deleted later - putchar(13); - putchar(10); - putchar('F'); -#endif + #if PUTCHAR_LOGS // TODO to be deleted later + putchar(13); + putchar(10); + putchar('F'); + #endif _hcd_data.frame_count++; -#if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - // retry EPs - for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { - max3421_ep_t * ep = &_hcd_data.ep[i]; - // set retryable EPs to pending - if (ep->state == EP_STATE_SUSPENDED) { -#if PUTCHAR_LOGS // TODO to be deleted later - putchar(ep->ep_dir ? 'r' : 'R'); - putchar('0' + ep->daddr); -// putchar('0' + ep->ep_num); -#endif + #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME + // retry EPs + for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { + max3421_ep_t * ep = &_hcd_data.ep[i]; + // set retryable EPs to pending + if (ep->state == EP_STATE_SUSPENDED) { ep->state = EP_STATE_PENDING; // trigger 1st retryable EP if (ep->packet_size) { // first test packet_size before atomic_flag_test_and_set() if (!atomic_flag_test_and_set(&_hcd_data.busy) ) { -#if PUTCHAR_LOGS // TODO to be deleted later - putchar(ep->ep_dir ? 't' : 'T'); - putchar('0' + ep->daddr); -// putchar('0' + ep->ep_num); -#endif + #if PUTCHAR_LOGS // TODO to be deleted later + putchar(ep->ep_dir ? 't' : 'T'); + putchar('0' + ep->daddr); +// putchar('0' + ep->ep_num); + #endif xact_inout(rhport, ep, true, in_isr); } } -- cgit v1.3.1 From fbb2818864d70e7e11879bf1c2daf2c22011f78b Mon Sep 17 00:00:00 2001 From: IngHK Date: Sun, 31 Mar 2024 09:25:51 +0200 Subject: added multiple attemp counting per frame --- src/portable/analog/max3421/hcd_max3421.c | 100 +++++++++++++++++++++--------- 1 file changed, 70 insertions(+), 30 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index dbdd2d127..6a38302b1 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -169,15 +169,33 @@ enum { }; enum { - EP_STATE_IDLE = 0, - EP_STATE_PENDING, -#if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - EP_STATE_SUSPENDED, -#endif - EP_STATE_COMPLETE + EP_STATE_IDLE = 0, + EP_STATE_ATTEMP1 = 1, // pending 1st attemp + #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME + EP_STATE_ATTEMP2 = 2, // don't change order + EP_STATE_ATTEMP3 = 3, // need to be incrementable + EP_STATE_ATTEMP4 = 4, + EP_STATE_ATTEMP5 = 5, + EP_STATE_ATTEMP6 = 6, + EP_STATE_ATTEMP7 = 7, + EP_STATE_ATTEMP8 = 8, + EP_STATE_ATTEMP9 = 9, + EP_STATE_ATTEMP10 = 10, + EP_STATE_SUSPENDED, // keep next behind last attemp + #endif + EP_STATE_COMPLETE, + EP_STATE_QUANTITY // not used. only to get quantity. keep last }; -TU_VERIFY_STATIC(CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME >= 0 && CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME <= 1, "unsupported attemp quantity"); +TU_VERIFY_STATIC(EP_STATE_QUANTITY <= 16, "no more than 16 states possible. ep->state has 4 bits"); + +#if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME + #define EP_STATE_ATTEMP_QUANTITY (EP_STATE_SUSPENDED - 1) + TU_VERIFY_STATIC(CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME >= 1 && + CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME <= EP_STATE_ATTEMP_QUANTITY, "unsupported attemp quantity"); +#else + #define EP_STATE_ATTEMP_QUANTITY 1 +#endif //--------------------------------------------------------------------+ // @@ -406,12 +424,16 @@ static void free_ep(uint8_t daddr) { } static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { + // search for next pending endpoint using round-robin scheduling + // if no other endpoint is pending and current endpoint is still pending, the current endpoint will be returned + // if no other endpoint is pending and current endpoint is not pending, NULL will be returned + // TODO maybe priorization control/interrupt/bulk/iso size_t const idx = (size_t) (cur_ep - _hcd_data.ep); // starting from next endpoint for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->state == EP_STATE_PENDING && ep->packet_size) { + if (ep->state >= EP_STATE_ATTEMP1 && ep->state <= EP_STATE_ATTEMP_QUANTITY && ep->packet_size) { // TU_LOG3("next pending i = %u\r\n", i); return ep; } @@ -420,7 +442,7 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // wrap around including current endpoint for (size_t i = 0; i <= idx; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->state == EP_STATE_PENDING && ep->packet_size) { + if (ep->state >= EP_STATE_ATTEMP1 && ep->state <= EP_STATE_ATTEMP_QUANTITY && ep->packet_size) { // TU_LOG3("next pending i = %u\r\n", i); return ep; } @@ -669,7 +691,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->buf = buffer; ep->total_len = buflen; ep->xferred_len = 0; - ep->state = EP_STATE_PENDING; + ep->state = EP_STATE_ATTEMP1; if ( ep_num == 0 ) { ep->is_setup = 0; @@ -706,7 +728,7 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] ep->buf = (uint8_t*)(uintptr_t) setup_packet; ep->total_len = 8; ep->xferred_len = 0; - ep->state = EP_STATE_PENDING; + ep->state = EP_STATE_ATTEMP1; // carry out transfer if not busy if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { @@ -824,6 +846,8 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { break; case HRSL_NAK: + // TODO no retry for iso in current frame + // TODO retry limitation over all (not only per frame) #if PUTCHAR_LOGS // TODO to be deleted later putchar(ep->ep_dir ? 'n' : 'N'); putchar('0' + ep->daddr); @@ -831,33 +855,38 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { putchar('0' + ep->state); #endif if (ep_num == 0) { - // NAK on control, retry immediately + // setup/control => retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); - } else { #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME + } else if (ep->state == CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME) { + // no more retry this frame if max. attemps are reached => suspend and retry it next frame ep->state = EP_STATE_SUSPENDED; + max3421_ep_t * next_ep = find_next_pending_ep(ep); if (next_ep) { - // switch to next pending TODO could have issue with double buffered if not clear previously out data + // switch to next pending endpoint TODO could have issue with double buffered if not clear previously out data xact_inout(rhport, next_ep, true, in_isr); } else { - // no more pending + // no more pending => clear busy atomic_flag_clear(&_hcd_data.busy); } - #else - // NAK on non-control, find next pending to switch - max3421_ep_t *next_ep = find_next_pending_ep(ep); + #endif + } else { + // another attemp + #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME + ep->state++; + #endif + max3421_ep_t * next_ep = find_next_pending_ep(ep); if (ep == next_ep) { - // this endpoint is only one pending, retry immediately + // this endpoint is only one pending => retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); } else if (next_ep) { - // switch to next pending TODO could have issue with double buffered if not clear previously out data + // switch to next pending endpoint TODO could have issue with double buffered if not clear previously out data xact_inout(rhport, next_ep, true, in_isr); } else { TU_ASSERT(false,); } - #endif } return; @@ -948,26 +977,37 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { _hcd_data.frame_count++; #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - // retry EPs + // endpoints retry or restart attemp next frame for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t * ep = &_hcd_data.ep[i]; - // set retryable EPs to pending + + // retry the endpoints that are suspended (NAK) last frame if (ep->state == EP_STATE_SUSPENDED) { - ep->state = EP_STATE_PENDING; - // trigger 1st retryable EP - if (ep->packet_size) { // first test packet_size before atomic_flag_test_and_set() - if (!atomic_flag_test_and_set(&_hcd_data.busy) ) { + // resume and retry suspended endpoint with attemp 1 + ep->state = EP_STATE_ATTEMP1; + + if (ep->packet_size) { // first test packet_size before atomic_flag_test_and_set() + if (!atomic_flag_test_and_set(&_hcd_data.busy) ) { + // trigger endpoint to be retried #if PUTCHAR_LOGS // TODO to be deleted later putchar(ep->ep_dir ? 't' : 'T'); putchar('0' + ep->daddr); // putchar('0' + ep->ep_num); #endif - xact_inout(rhport, ep, true, in_isr); + xact_inout(rhport, ep, true, in_isr); + } } + } else if (ep->state > EP_STATE_ATTEMP1 && ep->state <= CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME) { + // restart all other running/pending endpoints + #if PUTCHAR_LOGS // TODO to be deleted later + putchar(ep->ep_dir ? 'r' : 'R'); + putchar('0' + ep->daddr); +// putchar('0' + ep->ep_num); + #endif + ep->state = EP_STATE_ATTEMP1; } } - } -#endif + #endif LL_GPIO_SetOutputPin ( D2_GPIO_Port, D2_Pin << 16 ); } -- cgit v1.3.1 From c1a17a7369e326fad83b28d2abdef35d61d1f1ab Mon Sep 17 00:00:00 2001 From: IngHK Date: Sun, 31 Mar 2024 09:32:41 +0200 Subject: removed debug code --- src/portable/analog/max3421/hcd_max3421.c | 30 ------------------------------ 1 file changed, 30 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 6a38302b1..17d144c07 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -28,8 +28,6 @@ #if CFG_TUH_ENABLED && defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421 -#define PUTCHAR_LOGS 0 // TODO to be deleted later - #include #include "host/hcd.h" @@ -833,11 +831,6 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { xfer_result_t xfer_result; switch(hresult) { case HRSL_SUCCESS: - #if PUTCHAR_LOGS // TODO to be deleted later - putchar(ep->ep_dir ? 's' : 'S'); - putchar('0' + ep->daddr); -// putchar('0' + ep->ep_num); - #endif xfer_result = XFER_RESULT_SUCCESS; break; @@ -848,12 +841,6 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { case HRSL_NAK: // TODO no retry for iso in current frame // TODO retry limitation over all (not only per frame) - #if PUTCHAR_LOGS // TODO to be deleted later - putchar(ep->ep_dir ? 'n' : 'N'); - putchar('0' + ep->daddr); -// putchar('0' + ep->ep_num); - putchar('0' + ep->state); - #endif if (ep_num == 0) { // setup/control => retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); @@ -968,12 +955,6 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { // print_hirq(hirq); if (hirq & HIRQ_FRAME_IRQ) { - LL_GPIO_SetOutputPin ( D2_GPIO_Port, D2_Pin ); // TODO to be deleted later - #if PUTCHAR_LOGS // TODO to be deleted later - putchar(13); - putchar(10); - putchar('F'); - #endif _hcd_data.frame_count++; #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME @@ -989,26 +970,15 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { if (ep->packet_size) { // first test packet_size before atomic_flag_test_and_set() if (!atomic_flag_test_and_set(&_hcd_data.busy) ) { // trigger endpoint to be retried - #if PUTCHAR_LOGS // TODO to be deleted later - putchar(ep->ep_dir ? 't' : 'T'); - putchar('0' + ep->daddr); -// putchar('0' + ep->ep_num); - #endif xact_inout(rhport, ep, true, in_isr); } } } else if (ep->state > EP_STATE_ATTEMP1 && ep->state <= CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME) { // restart all other running/pending endpoints - #if PUTCHAR_LOGS // TODO to be deleted later - putchar(ep->ep_dir ? 'r' : 'R'); - putchar('0' + ep->daddr); -// putchar('0' + ep->ep_num); - #endif ep->state = EP_STATE_ATTEMP1; } } #endif - LL_GPIO_SetOutputPin ( D2_GPIO_Port, D2_Pin << 16 ); } if (hirq & HIRQ_CONDET_IRQ) { -- cgit v1.3.1 From fe304576d0875646a07ab56493f27a7a249ded35 Mon Sep 17 00:00:00 2001 From: IngHK Date: Sun, 31 Mar 2024 09:35:38 +0200 Subject: reactivated TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ,); --- src/portable/analog/max3421/hcd_max3421.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 17d144c07..84ea39d20 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -625,7 +625,7 @@ void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { } uint8_t const xact_len = (uint8_t) tu_min16(ep->total_len - ep->xferred_len, ep->packet_size); -// TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ,); + TU_ASSERT(_hcd_data.hirq & HIRQ_SNDBAV_IRQ,); if (xact_len) { fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, in_isr); } -- cgit v1.3.1 From b644e4d95582748dfc9ab947bbb32fd994f34448 Mon Sep 17 00:00:00 2001 From: IngHK Date: Sun, 31 Mar 2024 09:58:59 +0200 Subject: fixed spelling --- examples/host/bare_api/src/tusb_config.h | 2 +- examples/host/cdc_msc_hid/src/tusb_config.h | 2 +- .../host/cdc_msc_hid_freertos/src/tusb_config.h | 2 +- examples/host/hid_controller/src/tusb_config.h | 2 +- examples/host/msc_file_explorer/src/tusb_config.h | 2 +- src/portable/analog/max3421/hcd_max3421.c | 68 +++++++++++----------- src/tusb_option.h | 8 +-- 7 files changed, 43 insertions(+), 43 deletions(-) (limited to 'src/portable') diff --git a/examples/host/bare_api/src/tusb_config.h b/examples/host/bare_api/src/tusb_config.h index 8bdcb4fba..d8e81aa82 100644 --- a/examples/host/bare_api/src/tusb_config.h +++ b/examples/host/bare_api/src/tusb_config.h @@ -72,7 +72,7 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME 3 // max. transfer attemps per frame + // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/examples/host/cdc_msc_hid/src/tusb_config.h b/examples/host/cdc_msc_hid/src/tusb_config.h index 371ed807e..8a56ebc2b 100644 --- a/examples/host/cdc_msc_hid/src/tusb_config.h +++ b/examples/host/cdc_msc_hid/src/tusb_config.h @@ -72,7 +72,7 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME 3 // max. transfer attemps per frame + // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/examples/host/cdc_msc_hid_freertos/src/tusb_config.h b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h index 621b97865..7705be5c8 100644 --- a/examples/host/cdc_msc_hid_freertos/src/tusb_config.h +++ b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h @@ -77,7 +77,7 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME 3 // max. transfer attemps per frame + // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/examples/host/hid_controller/src/tusb_config.h b/examples/host/hid_controller/src/tusb_config.h index 8036e9f66..f087a93cf 100644 --- a/examples/host/hid_controller/src/tusb_config.h +++ b/examples/host/hid_controller/src/tusb_config.h @@ -72,7 +72,7 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME 3 // max. transfer attemps per frame + // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/examples/host/msc_file_explorer/src/tusb_config.h b/examples/host/msc_file_explorer/src/tusb_config.h index 3ac3f3cdf..05b9fa174 100644 --- a/examples/host/msc_file_explorer/src/tusb_config.h +++ b/examples/host/msc_file_explorer/src/tusb_config.h @@ -72,7 +72,7 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME 3 // max. transfer attemps per frame + // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 84ea39d20..324638cb8 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -167,19 +167,19 @@ enum { }; enum { - EP_STATE_IDLE = 0, - EP_STATE_ATTEMP1 = 1, // pending 1st attemp - #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - EP_STATE_ATTEMP2 = 2, // don't change order - EP_STATE_ATTEMP3 = 3, // need to be incrementable - EP_STATE_ATTEMP4 = 4, - EP_STATE_ATTEMP5 = 5, - EP_STATE_ATTEMP6 = 6, - EP_STATE_ATTEMP7 = 7, - EP_STATE_ATTEMP8 = 8, - EP_STATE_ATTEMP9 = 9, - EP_STATE_ATTEMP10 = 10, - EP_STATE_SUSPENDED, // keep next behind last attemp + EP_STATE_IDLE = 0, + EP_STATE_ATTEMPT1 = 1, // pending 1st attempt + #if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME + EP_STATE_ATTEMPT2 = 2, // don't change order + EP_STATE_ATTEMPT3 = 3, // need to be incrementable + EP_STATE_ATTEMPT4 = 4, + EP_STATE_ATTEMPT5 = 5, + EP_STATE_ATTEMPT6 = 6, + EP_STATE_ATTEMPT7 = 7, + EP_STATE_ATTEMPT8 = 8, + EP_STATE_ATTEMPT9 = 9, + EP_STATE_ATTEMPT10 = 10, + EP_STATE_SUSPENDED, // keep next behind last attempt #endif EP_STATE_COMPLETE, EP_STATE_QUANTITY // not used. only to get quantity. keep last @@ -187,12 +187,12 @@ enum { TU_VERIFY_STATIC(EP_STATE_QUANTITY <= 16, "no more than 16 states possible. ep->state has 4 bits"); -#if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - #define EP_STATE_ATTEMP_QUANTITY (EP_STATE_SUSPENDED - 1) - TU_VERIFY_STATIC(CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME >= 1 && - CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME <= EP_STATE_ATTEMP_QUANTITY, "unsupported attemp quantity"); +#if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME + #define EP_STATE_ATTEMPT_QUANTITY (EP_STATE_SUSPENDED - 1) + TU_VERIFY_STATIC(CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME >= 1 && + CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME <= EP_STATE_ATTEMPT_QUANTITY, "unsupported attempt quantity"); #else - #define EP_STATE_ATTEMP_QUANTITY 1 + #define EP_STATE_ATTEMPT_QUANTITY 1 #endif //--------------------------------------------------------------------+ @@ -425,13 +425,13 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // search for next pending endpoint using round-robin scheduling // if no other endpoint is pending and current endpoint is still pending, the current endpoint will be returned // if no other endpoint is pending and current endpoint is not pending, NULL will be returned - // TODO maybe priorization control/interrupt/bulk/iso + // TODO maybe prioritisation control/interrupt/bulk/iso size_t const idx = (size_t) (cur_ep - _hcd_data.ep); // starting from next endpoint for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->state >= EP_STATE_ATTEMP1 && ep->state <= EP_STATE_ATTEMP_QUANTITY && ep->packet_size) { + if (ep->state >= EP_STATE_ATTEMPT1 && ep->state <= EP_STATE_ATTEMPT_QUANTITY && ep->packet_size) { // TU_LOG3("next pending i = %u\r\n", i); return ep; } @@ -440,7 +440,7 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // wrap around including current endpoint for (size_t i = 0; i <= idx; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->state >= EP_STATE_ATTEMP1 && ep->state <= EP_STATE_ATTEMP_QUANTITY && ep->packet_size) { + if (ep->state >= EP_STATE_ATTEMPT1 && ep->state <= EP_STATE_ATTEMPT_QUANTITY && ep->packet_size) { // TU_LOG3("next pending i = %u\r\n", i); return ep; } @@ -689,7 +689,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->buf = buffer; ep->total_len = buflen; ep->xferred_len = 0; - ep->state = EP_STATE_ATTEMP1; + ep->state = EP_STATE_ATTEMPT1; if ( ep_num == 0 ) { ep->is_setup = 0; @@ -726,7 +726,7 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] ep->buf = (uint8_t*)(uintptr_t) setup_packet; ep->total_len = 8; ep->xferred_len = 0; - ep->state = EP_STATE_ATTEMP1; + ep->state = EP_STATE_ATTEMPT1; // carry out transfer if not busy if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { @@ -844,9 +844,9 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { if (ep_num == 0) { // setup/control => retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); - #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - } else if (ep->state == CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME) { - // no more retry this frame if max. attemps are reached => suspend and retry it next frame + #if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME + } else if (ep->state == CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME) { + // no more retry this frame if max. attempts are reached => suspend and retry it next frame ep->state = EP_STATE_SUSPENDED; max3421_ep_t * next_ep = find_next_pending_ep(ep); @@ -859,8 +859,8 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { } #endif } else { - // another attemp - #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME + // another attempt + #if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME ep->state++; #endif @@ -957,15 +957,15 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { if (hirq & HIRQ_FRAME_IRQ) { _hcd_data.frame_count++; - #if CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - // endpoints retry or restart attemp next frame + #if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME + // endpoints retry or restart attempt next frame for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t * ep = &_hcd_data.ep[i]; // retry the endpoints that are suspended (NAK) last frame if (ep->state == EP_STATE_SUSPENDED) { - // resume and retry suspended endpoint with attemp 1 - ep->state = EP_STATE_ATTEMP1; + // resume and retry suspended endpoint with attempt 1 + ep->state = EP_STATE_ATTEMPT1; if (ep->packet_size) { // first test packet_size before atomic_flag_test_and_set() if (!atomic_flag_test_and_set(&_hcd_data.busy) ) { @@ -973,9 +973,9 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { xact_inout(rhport, ep, true, in_isr); } } - } else if (ep->state > EP_STATE_ATTEMP1 && ep->state <= CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME) { + } else if (ep->state > EP_STATE_ATTEMPT1 && ep->state <= CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME) { // restart all other running/pending endpoints - ep->state = EP_STATE_ATTEMP1; + ep->state = EP_STATE_ATTEMPT1; } } #endif diff --git a/src/tusb_option.h b/src/tusb_option.h index 64915cf62..18cc8a82c 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -529,14 +529,14 @@ #define CFG_TUH_MAX3421 0 #endif -// MAX3421 Host max. transfer attemps per frame (except control and iso) +// MAX3421 Host max. transfer attempts per frame (except control and iso) // retry quantity = (CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - 1) // 0 = endless retries. is default to keep compatibility // => this may overload MCU with permanently repeating NAK interrupts // => possible increased USB traffic, increased latencies, reduced data throughput -// a usual attemp quantity is 3 (reference: the book "USB Complete" by Jan Axelson) -#ifndef CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - #define CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME 0 +// a usual attempt quantity is 3 (reference: the book "USB Complete" by Jan Axelson) +#ifndef CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME + #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 0 #endif -- cgit v1.3.1 From ac4e649e56b7ace537670d1cc261a64a4e650d02 Mon Sep 17 00:00:00 2001 From: hathach Date: Sun, 31 Mar 2024 18:41:59 +0700 Subject: code format --- .../st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 176 +++++++++------------ 1 file changed, 71 insertions(+), 105 deletions(-) (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h index ade64b4fb..15de95d23 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h @@ -1,30 +1,32 @@ -/** - * Copyright(c) 2016 STMicroelectronics - * Copyright(c) N Conrad - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - */ +/* + * Copyright(c) 2016 STMicroelectronics + * Copyright(c) N Conrad + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * This file is part of the TinyUSB stack. + */ // This file contains source copied from ST's HAL, and thus should have their copyright statement. @@ -138,7 +140,6 @@ #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY #define USB_CNTR_FSUSP USB_CNTR_SUSPEN - #elif CFG_TUSB_MCU == OPT_MCU_STM32WB #include "stm32wbxx.h" #define FSDEV_PMA_SIZE (1024u) @@ -182,27 +183,23 @@ typedef uint16_t fsdev_bus_t; // Volatile is also needed to prevent the optimizer from changing access to 32-bit (as 32-bit access is forbidden) static __IO uint16_t * const pma = (__IO uint16_t*)USB_PMAADDR; -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t * pcd_btable_word_ptr(USB_TypeDef * USBx, size_t x) -{ +TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t * pcd_btable_word_ptr(USB_TypeDef * USBx, size_t x) { size_t total_word_offset = (((USBx)->BTABLE)>>1) + x; total_word_offset *= FSDEV_PMA_STRIDE; return &(pma[total_word_offset]); } -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_tx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_tx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) { return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 1u); } -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_rx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_rx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) { return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 3u); } #endif /* Aligned buffer size according to hardware */ -TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_aligned_buffer_size(uint16_t size) -{ +TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_aligned_buffer_size(uint16_t size) { /* The STM32 full speed USB peripheral supports only a limited set of * buffer sizes given by the RX buffer entry format in the USB_BTABLE. */ uint16_t blocksize = (size > 62) ? 32 : 2; @@ -213,9 +210,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_aligned_buffer_size(uint16_t si return numblocks * blocksize; } -/* SetENDPOINT */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wRegValue) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wRegValue) { #ifdef FSDEV_BUS_32BIT (void) USBx; __O uint32_t *reg = (__O uint32_t *)(USB_DRD_BASE + bEpIdx*4); @@ -226,7 +221,6 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, ui #endif } -/* GetENDPOINT */ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef FSDEV_BUS_32BIT (void) USBx; @@ -237,8 +231,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_endpoint(USB_TypeDef * USBx return *reg; } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_eptype(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wType) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_eptype(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wType) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= (uint32_t)USB_EP_T_MASK; regVal |= wType; @@ -246,20 +239,19 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_eptype(USB_TypeDef * USBx, uint pcd_set_endpoint(USBx, bEpIdx, regVal); } -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_eptype(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_eptype(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= USB_EP_T_FIELD; return regVal; } + /** * @brief Clears bit CTR_RX / CTR_TX in the endpoint register. * @param USBx USB peripheral instance register address. * @param bEpIdx Endpoint Number. * @retval None */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_rx_ep_ctr(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_rx_ep_ctr(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= USB_EPREG_MASK; regVal &= ~USB_EP_CTR_RX; @@ -267,22 +259,21 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_rx_ep_ctr(USB_TypeDef * USBx, pcd_set_endpoint(USBx, bEpIdx, regVal); } -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_ep_ctr(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_ep_ctr(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= USB_EPREG_MASK; regVal &= ~USB_EP_CTR_TX; regVal |= USB_EP_CTR_RX; // preserve CTR_RX (clears on writing 0) pcd_set_endpoint(USBx, bEpIdx,regVal); } + /** * @brief gets counter of the tx buffer. * @param USBx USB peripheral instance register address. * @param bEpIdx Endpoint Number. * @retval Counter value */ -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef FSDEV_BUS_32BIT (void) USBx; return (pma32[2*bEpIdx] & 0x03FF0000) >> 16; @@ -292,8 +283,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USB #endif } -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef FSDEV_BUS_32BIT (void) USBx; /* WA: few cycles for RX PMA descriptor to update, otherwise doesn't return the correct value. @@ -320,8 +310,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USB * @param bAddr Address. * @retval None */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t bAddr) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t bAddr) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= USB_EPREG_MASK; regVal |= bAddr; @@ -329,8 +318,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_address(USB_TypeDef * USBx, pcd_set_endpoint(USBx, bEpIdx,regVal); } -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef FSDEV_BUS_32BIT (void) USBx; return pma32[2*bEpIdx] & 0x0000FFFFu ; @@ -339,8 +327,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * #endif } -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef FSDEV_BUS_32BIT (void) USBx; return pma32[2*bEpIdx + 1] & 0x0000FFFFu; @@ -349,8 +336,7 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * #endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { #ifdef FSDEV_BUS_32BIT (void) USBx; pma32[2*bEpIdx] = (pma32[2*bEpIdx] & 0xFFFF0000u) | (addr & 0x0000FFFCu); @@ -359,8 +345,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USB #endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { #ifdef FSDEV_BUS_32BIT (void) USBx; pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & 0xFFFF0000u) | (addr & 0x0000FFFCu); @@ -369,8 +354,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USB #endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { #ifdef FSDEV_BUS_32BIT (void) USBx; pma32[2*bEpIdx] = (pma32[2*bEpIdx] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); @@ -380,8 +364,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, u #endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { #ifdef FSDEV_BUS_32BIT (void) USBx; pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); @@ -391,8 +374,8 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, u #endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_blsize_num_blocks(USB_TypeDef * USBx, uint32_t rxtx_idx, uint32_t blocksize, uint32_t numblocks) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_blsize_num_blocks(USB_TypeDef * USBx, uint32_t rxtx_idx, + uint32_t blocksize, uint32_t numblocks) { /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ #ifdef FSDEV_BUS_32BIT (void) USBx; @@ -403,8 +386,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_blsize_num_blocks(USB_TypeDe #endif } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_bufsize(USB_TypeDef * USBx, uint32_t rxtx_idx, uint32_t wCount) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_bufsize(USB_TypeDef * USBx, uint32_t rxtx_idx, uint32_t wCount) { wCount = pcd_aligned_buffer_size(wCount); /* We assume that the buffer size is already aligned to hardware requirements. */ @@ -418,13 +400,11 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_bufsize(USB_TypeDef * USBx, pcd_set_ep_blsize_num_blocks(USBx, rxtx_idx, blocksize, numblocks); } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { pcd_set_ep_bufsize(USBx, 2*bEpIdx, wCount); } -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { pcd_set_ep_bufsize(USBx, 2*bEpIdx + 1, wCount); } @@ -435,8 +415,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_bufsize(USB_TypeDef * USB * @param wState new state * @retval None */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_status(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wState) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_status(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wState) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= USB_EPTX_DTOGMASK; @@ -453,7 +432,7 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_status(USB_TypeDef * USBx regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; pcd_set_endpoint(USBx, bEpIdx, regVal); -} /* pcd_set_ep_tx_status */ +} /** * @brief sets the status for rx transfer (bits STAT_TX[1:0]) @@ -463,31 +442,27 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_status(USB_TypeDef * USBx * @retval None */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_status(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wState) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_status(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wState) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= USB_EPRX_DTOGMASK; /* toggle first bit ? */ - if((USB_EPRX_DTOG1 & wState)!= 0U) - { + if((USB_EPRX_DTOG1 & wState)!= 0U) { regVal ^= USB_EPRX_DTOG1; } /* toggle second bit ? */ - if((USB_EPRX_DTOG2 & wState)!= 0U) - { + if((USB_EPRX_DTOG2 & wState)!= 0U) { regVal ^= USB_EPRX_DTOG2; } regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; pcd_set_endpoint(USBx, bEpIdx, regVal); -} /* pcd_set_ep_rx_status */ +} -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_status(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_status(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); return (regVal & USB_EPRX_STAT) >> (12u); -} /* pcd_get_ep_rx_status */ +} /** @@ -496,16 +471,14 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_status(USB_TypeDef * * @param bEpIdx Endpoint Number. * @retval None */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_rx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_rx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= USB_EPREG_MASK; regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX|USB_EP_DTOG_RX; pcd_set_endpoint(USBx, bEpIdx, regVal); } -TU_ATTR_ALWAYS_INLINE static inline void pcd_tx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_tx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= USB_EPREG_MASK; regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX|USB_EP_DTOG_TX; @@ -518,21 +491,16 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_tx_dtog(USB_TypeDef * USBx, uint32 * @param bEpIdx Endpoint Number. * @retval None */ - -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_rx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_rx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - if((regVal & USB_EP_DTOG_RX) != 0) - { + if((regVal & USB_EP_DTOG_RX) != 0) { pcd_rx_dtog(USBx,bEpIdx); } } -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - if((regVal & USB_EP_DTOG_TX) != 0) - { + if((regVal & USB_EP_DTOG_TX) != 0) { pcd_tx_dtog(USBx,bEpIdx); } } @@ -543,17 +511,15 @@ TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_dtog(USB_TypeDef * USBx, * @param bEpIdx Endpoint Number. * @retval None */ - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_kind(USB_TypeDef * USBx, uint32_t bEpIdx) -{ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_kind(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal |= USB_EP_KIND; regVal &= USB_EPREG_MASK; regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; pcd_set_endpoint(USBx, bEpIdx, regVal); } -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_ep_kind(USB_TypeDef * USBx, uint32_t bEpIdx) -{ + +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_ep_kind(USB_TypeDef * USBx, uint32_t bEpIdx) { uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); regVal &= USB_EPKIND_MASK; regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; -- cgit v1.3.1 From 27afa568445d193a075c6ca2b7bb1df76039d956 Mon Sep 17 00:00:00 2001 From: hathach Date: Sun, 31 Mar 2024 18:42:49 +0700 Subject: rename dcd_stm32_fsdev_pvt_st.h to simply dcd_stm32_fsdev.h --- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 2 +- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h | 543 +++++++++++++++++++++ .../st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h | 543 --------------------- 3 files changed, 544 insertions(+), 544 deletions(-) create mode 100644 src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h delete mode 100644 src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h (limited to 'src/portable') diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 9c37f1f98..5e54d0f56 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -109,7 +109,7 @@ #ifdef TUP_USBIP_FSDEV_STM32 // Undefine to reduce the dependence on HAL #undef USE_HAL_DRIVER - #include "portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h" + #include "portable/st/stm32_fsdev/dcd_stm32_fsdev.h" #endif /***************************************************** diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h new file mode 100644 index 000000000..15de95d23 --- /dev/null +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h @@ -0,0 +1,543 @@ +/* + * Copyright(c) 2016 STMicroelectronics + * Copyright(c) N Conrad + * Copyright (c) 2019 Ha Thach (tinyusb.org) + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + * This file is part of the TinyUSB stack. + */ + +// This file contains source copied from ST's HAL, and thus should have their copyright statement. + +// FSDEV_PMA_SIZE is PMA buffer size in bytes. +// On 512-byte devices, access with a stride of two words (use every other 16-bit address) +// On 1024-byte devices, access with a stride of one word (use every 16-bit address) + +#ifndef PORTABLE_ST_STM32F0_DCD_STM32F0_FSDEV_PVT_ST_H_ +#define PORTABLE_ST_STM32F0_DCD_STM32F0_FSDEV_PVT_ST_H_ + +#if CFG_TUSB_MCU == OPT_MCU_STM32F0 + #include "stm32f0xx.h" + #define FSDEV_PMA_SIZE (1024u) + // F0x2 models are crystal-less + // All have internal D+ pull-up + // 070RB: 2 x 16 bits/word memory LPM Support, BCD Support + // PMA dedicated to USB (no sharing with CAN) + +#elif CFG_TUSB_MCU == OPT_MCU_STM32F1 + #include "stm32f1xx.h" + #define FSDEV_PMA_SIZE (512u) + // NO internal Pull-ups + // *B, and *C: 2 x 16 bits/word + + // F1 names this differently from the rest + #define USB_CNTR_LPMODE USB_CNTR_LP_MODE + +#elif defined(STM32F302xB) || defined(STM32F302xC) || \ + defined(STM32F303xB) || defined(STM32F303xC) || \ + defined(STM32F373xC) + #include "stm32f3xx.h" + #define FSDEV_PMA_SIZE (512u) + // NO internal Pull-ups + // *B, and *C: 1 x 16 bits/word + // PMA dedicated to USB (no sharing with CAN) + +#elif defined(STM32F302x6) || defined(STM32F302x8) || \ + defined(STM32F302xD) || defined(STM32F302xE) || \ + defined(STM32F303xD) || defined(STM32F303xE) + #include "stm32f3xx.h" + #define FSDEV_PMA_SIZE (1024u) + // NO internal Pull-ups + // *6, *8, *D, and *E: 2 x 16 bits/word LPM Support + // When CAN clock is enabled, USB can use first 768 bytes ONLY. + +#elif CFG_TUSB_MCU == OPT_MCU_STM32L0 + #include "stm32l0xx.h" + #define FSDEV_PMA_SIZE (1024u) + +#elif CFG_TUSB_MCU == OPT_MCU_STM32L1 + #include "stm32l1xx.h" + #define FSDEV_PMA_SIZE (512u) + +#elif CFG_TUSB_MCU == OPT_MCU_STM32G4 + #include "stm32g4xx.h" + #define FSDEV_PMA_SIZE (1024u) + +#elif CFG_TUSB_MCU == OPT_MCU_STM32G0 + #include "stm32g0xx.h" + #define FSDEV_BUS_32BIT + #define FSDEV_PMA_SIZE (2048u) + #undef USB_PMAADDR + #define USB_PMAADDR USB_DRD_PMAADDR + #define USB_TypeDef USB_DRD_TypeDef + #define EP0R CHEP0R + #define USB_EP_CTR_RX USB_EP_VTRX + #define USB_EP_CTR_TX USB_EP_VTTX + #define USB_EP_T_FIELD USB_CHEP_UTYPE + #define USB_EPREG_MASK USB_CHEP_REG_MASK + #define USB_EPTX_DTOGMASK USB_CHEP_TX_DTOGMASK + #define USB_EPRX_DTOGMASK USB_CHEP_RX_DTOGMASK + #define USB_EPTX_DTOG1 USB_CHEP_TX_DTOG1 + #define USB_EPTX_DTOG2 USB_CHEP_TX_DTOG2 + #define USB_EPRX_DTOG1 USB_CHEP_RX_DTOG1 + #define USB_EPRX_DTOG2 USB_CHEP_RX_DTOG2 + #define USB_EPRX_STAT USB_CH_RX_VALID + #define USB_EPKIND_MASK USB_EP_KIND_MASK + #define USB USB_DRD_FS + #define USB_CNTR_FRES USB_CNTR_USBRST + #define USB_CNTR_RESUME USB_CNTR_L2RES + #define USB_ISTR_EP_ID USB_ISTR_IDN + #define USB_EPADDR_FIELD USB_CHEP_ADDR + #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY + #define USB_CNTR_FSUSP USB_CNTR_SUSPEN + +#elif CFG_TUSB_MCU == OPT_MCU_STM32H5 + #include "stm32h5xx.h" + #define FSDEV_BUS_32BIT + #define FSDEV_PMA_SIZE (2048u) + #undef USB_PMAADDR + #define USB_PMAADDR USB_DRD_PMAADDR + #define USB_TypeDef USB_DRD_TypeDef + #define EP0R CHEP0R + #define USB_EP_CTR_RX USB_EP_VTRX + #define USB_EP_CTR_TX USB_EP_VTTX + #define USB_EP_T_FIELD USB_CHEP_UTYPE + #define USB_EPREG_MASK USB_CHEP_REG_MASK + #define USB_EPTX_DTOGMASK USB_CHEP_TX_DTOGMASK + #define USB_EPRX_DTOGMASK USB_CHEP_RX_DTOGMASK + #define USB_EPTX_DTOG1 USB_CHEP_TX_DTOG1 + #define USB_EPTX_DTOG2 USB_CHEP_TX_DTOG2 + #define USB_EPRX_DTOG1 USB_CHEP_RX_DTOG1 + #define USB_EPRX_DTOG2 USB_CHEP_RX_DTOG2 + #define USB_EPRX_STAT USB_CH_RX_VALID + #define USB_EPKIND_MASK USB_EP_KIND_MASK + #define USB USB_DRD_FS + #define USB_CNTR_FRES USB_CNTR_USBRST + #define USB_CNTR_RESUME USB_CNTR_L2RES + #define USB_ISTR_EP_ID USB_ISTR_IDN + #define USB_EPADDR_FIELD USB_CHEP_ADDR + #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY + #define USB_CNTR_FSUSP USB_CNTR_SUSPEN + +#elif CFG_TUSB_MCU == OPT_MCU_STM32WB + #include "stm32wbxx.h" + #define FSDEV_PMA_SIZE (1024u) + /* ST provided header has incorrect value */ + #undef USB_PMAADDR + #define USB_PMAADDR USB1_PMAADDR + +#elif CFG_TUSB_MCU == OPT_MCU_STM32L4 + #include "stm32l4xx.h" + #define FSDEV_PMA_SIZE (1024u) + +#elif CFG_TUSB_MCU == OPT_MCU_STM32L5 + #include "stm32l5xx.h" + #define FSDEV_PMA_SIZE (1024u) + + #ifndef USB_PMAADDR + #define USB_PMAADDR (USB_BASE + (USB_PMAADDR_NS - USB_BASE_NS)) + #endif + +#else + #error You are using an untested or unimplemented STM32 variant. Please update the driver. + // This includes L1x0, L1x1, L1x2, L4x2 and L4x3, G1x1, G1x3, and G1x4 +#endif + +// For purposes of accessing the packet +#if ((FSDEV_PMA_SIZE) == 512u) + #define FSDEV_PMA_STRIDE (2u) +#elif ((FSDEV_PMA_SIZE) == 1024u) + #define FSDEV_PMA_STRIDE (1u) +#endif + +// The fsdev_bus_t type can be used for both register and PMA access necessities +// For type-safety create a new macro for the volatile address of PMAADDR +// The compiler should warn us if we cast it to a non-volatile type? +#ifdef FSDEV_BUS_32BIT +typedef uint32_t fsdev_bus_t; +static __IO uint32_t * const pma32 = (__IO uint32_t*)USB_PMAADDR; + +#else +typedef uint16_t fsdev_bus_t; +// Volatile is also needed to prevent the optimizer from changing access to 32-bit (as 32-bit access is forbidden) +static __IO uint16_t * const pma = (__IO uint16_t*)USB_PMAADDR; + +TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t * pcd_btable_word_ptr(USB_TypeDef * USBx, size_t x) { + size_t total_word_offset = (((USBx)->BTABLE)>>1) + x; + total_word_offset *= FSDEV_PMA_STRIDE; + return &(pma[total_word_offset]); +} + +TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_tx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) { + return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 1u); +} + +TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_rx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) { + return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 3u); +} +#endif + +/* Aligned buffer size according to hardware */ +TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_aligned_buffer_size(uint16_t size) { + /* The STM32 full speed USB peripheral supports only a limited set of + * buffer sizes given by the RX buffer entry format in the USB_BTABLE. */ + uint16_t blocksize = (size > 62) ? 32 : 2; + + // Round up while dividing requested size by blocksize + uint16_t numblocks = (size + blocksize - 1) / blocksize ; + + return numblocks * blocksize; +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wRegValue) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + __O uint32_t *reg = (__O uint32_t *)(USB_DRD_BASE + bEpIdx*4); + *reg = wRegValue; +#else + __O uint16_t *reg = (__O uint16_t *)((&USBx->EP0R) + bEpIdx*2u); + *reg = (uint16_t)wRegValue; +#endif +} + +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + __I uint32_t *reg = (__I uint32_t *)(USB_DRD_BASE + bEpIdx*4); +#else + __I uint16_t *reg = (__I uint16_t *)((&USBx->EP0R) + bEpIdx*2u); +#endif + return *reg; +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_eptype(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wType) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= (uint32_t)USB_EP_T_MASK; + regVal |= wType; + regVal |= USB_EP_CTR_RX | USB_EP_CTR_TX; // These clear on write0, so must set high + pcd_set_endpoint(USBx, bEpIdx, regVal); +} + +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_eptype(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= USB_EP_T_FIELD; + return regVal; +} + +/** + * @brief Clears bit CTR_RX / CTR_TX in the endpoint register. + * @param USBx USB peripheral instance register address. + * @param bEpIdx Endpoint Number. + * @retval None + */ +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_rx_ep_ctr(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= USB_EPREG_MASK; + regVal &= ~USB_EP_CTR_RX; + regVal |= USB_EP_CTR_TX; // preserve CTR_TX (clears on writing 0) + pcd_set_endpoint(USBx, bEpIdx, regVal); +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_ep_ctr(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= USB_EPREG_MASK; + regVal &= ~USB_EP_CTR_TX; + regVal |= USB_EP_CTR_RX; // preserve CTR_RX (clears on writing 0) + pcd_set_endpoint(USBx, bEpIdx,regVal); +} + +/** + * @brief gets counter of the tx buffer. + * @param USBx USB peripheral instance register address. + * @param bEpIdx Endpoint Number. + * @retval Counter value + */ +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + return (pma32[2*bEpIdx] & 0x03FF0000) >> 16; +#else + __I uint16_t *regPtr = pcd_ep_tx_cnt_ptr(USBx, bEpIdx); + return *regPtr & 0x3ffU; +#endif +} + +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + /* WA: few cycles for RX PMA descriptor to update, otherwise doesn't return the correct value. + Note: required for G0, U5, H5 etc. + This workaround is ported from stm32h5xx_hal_pcd.h and fixes the issue when calling this function fast enough. + Reproduced with GCC ast optimization(O2/O3) and stm32h573i_dk with an high frequency. + Observed on Windows 10 where tud_task() is scheduled by interrupt handler. + */ + volatile uint32_t count = 10; // defined as PCD_RX_PMA_CNT in stm32 hal_driver + while (count > 0U) { + count--; + } + return (pma32[2*bEpIdx + 1] & 0x03FF0000) >> 16; +#else + __I uint16_t *regPtr = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); + return *regPtr & 0x3ffU; +#endif +} + +/** + * @brief Sets address in an endpoint register. + * @param USBx USB peripheral instance register address. + * @param bEpIdx Endpoint Number. + * @param bAddr Address. + * @retval None + */ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t bAddr) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= USB_EPREG_MASK; + regVal |= bAddr; + regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; + pcd_set_endpoint(USBx, bEpIdx,regVal); +} + +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + return pma32[2*bEpIdx] & 0x0000FFFFu ; +#else + return *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 0u); +#endif +} + +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + return pma32[2*bEpIdx + 1] & 0x0000FFFFu; +#else + return *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 2u); +#endif +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + pma32[2*bEpIdx] = (pma32[2*bEpIdx] & 0xFFFF0000u) | (addr & 0x0000FFFCu); +#else + *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 0u) = addr; +#endif +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & 0xFFFF0000u) | (addr & 0x0000FFFCu); +#else + *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 2u) = addr; +#endif +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + pma32[2*bEpIdx] = (pma32[2*bEpIdx] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); +#else + __IO uint16_t * reg = pcd_ep_tx_cnt_ptr(USBx, bEpIdx); + *reg = (uint16_t) (*reg & (uint16_t) ~0x3FFU) | (wCount & 0x3FFU); +#endif +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { +#ifdef FSDEV_BUS_32BIT + (void) USBx; + pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); +#else + __IO uint16_t * reg = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); + *reg = (uint16_t) (*reg & (uint16_t) ~0x3FFU) | (wCount & 0x3FFU); +#endif +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_blsize_num_blocks(USB_TypeDef * USBx, uint32_t rxtx_idx, + uint32_t blocksize, uint32_t numblocks) { + /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ +#ifdef FSDEV_BUS_32BIT + (void) USBx; + pma32[rxtx_idx] = (pma32[rxtx_idx] & 0x0000FFFFu) | (blocksize << 31) | ((numblocks - blocksize) << 26); +#else + __IO uint16_t *pdwReg = pcd_btable_word_ptr(USBx, rxtx_idx*2u + 1u); + *pdwReg = (blocksize << 15) | ((numblocks - blocksize) << 10); +#endif +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_bufsize(USB_TypeDef * USBx, uint32_t rxtx_idx, uint32_t wCount) { + wCount = pcd_aligned_buffer_size(wCount); + + /* We assume that the buffer size is already aligned to hardware requirements. */ + uint16_t blocksize = (wCount > 62) ? 1 : 0; + uint16_t numblocks = wCount / (blocksize ? 32 : 2); + + /* There should be no remainder in the above calculation */ + TU_ASSERT((wCount - (numblocks * (blocksize ? 32 : 2))) == 0, /**/); + + /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ + pcd_set_ep_blsize_num_blocks(USBx, rxtx_idx, blocksize, numblocks); +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { + pcd_set_ep_bufsize(USBx, 2*bEpIdx, wCount); +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { + pcd_set_ep_bufsize(USBx, 2*bEpIdx + 1, wCount); +} + +/** + * @brief sets the status for tx transfer (bits STAT_TX[1:0]). + * @param USBx USB peripheral instance register address. + * @param bEpIdx Endpoint Number. + * @param wState new state + * @retval None + */ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_status(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wState) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= USB_EPTX_DTOGMASK; + + /* toggle first bit ? */ + if((USB_EPTX_DTOG1 & (wState))!= 0U) + { + regVal ^= USB_EPTX_DTOG1; + } + /* toggle second bit ? */ + if((USB_EPTX_DTOG2 & ((uint32_t)(wState)))!= 0U) + { + regVal ^= USB_EPTX_DTOG2; + } + + regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; + pcd_set_endpoint(USBx, bEpIdx, regVal); +} + +/** + * @brief sets the status for rx transfer (bits STAT_TX[1:0]) + * @param USBx USB peripheral instance register address. + * @param bEpIdx Endpoint Number. + * @param wState new state + * @retval None + */ + +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_status(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wState) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= USB_EPRX_DTOGMASK; + + /* toggle first bit ? */ + if((USB_EPRX_DTOG1 & wState)!= 0U) { + regVal ^= USB_EPRX_DTOG1; + } + /* toggle second bit ? */ + if((USB_EPRX_DTOG2 & wState)!= 0U) { + regVal ^= USB_EPRX_DTOG2; + } + + regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; + pcd_set_endpoint(USBx, bEpIdx, regVal); +} + +TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_status(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + return (regVal & USB_EPRX_STAT) >> (12u); +} + + +/** + * @brief Toggles DTOG_RX / DTOG_TX bit in the endpoint register. + * @param USBx USB peripheral instance register address. + * @param bEpIdx Endpoint Number. + * @retval None + */ +TU_ATTR_ALWAYS_INLINE static inline void pcd_rx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= USB_EPREG_MASK; + regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX|USB_EP_DTOG_RX; + pcd_set_endpoint(USBx, bEpIdx, regVal); +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_tx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= USB_EPREG_MASK; + regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX|USB_EP_DTOG_TX; + pcd_set_endpoint(USBx, bEpIdx, regVal); +} + +/** + * @brief Clears DTOG_RX / DTOG_TX bit in the endpoint register. + * @param USBx USB peripheral instance register address. + * @param bEpIdx Endpoint Number. + * @retval None + */ +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_rx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + if((regVal & USB_EP_DTOG_RX) != 0) { + pcd_rx_dtog(USBx,bEpIdx); + } +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + if((regVal & USB_EP_DTOG_TX) != 0) { + pcd_tx_dtog(USBx,bEpIdx); + } +} + +/** + * @brief set & clear EP_KIND bit. + * @param USBx USB peripheral instance register address. + * @param bEpIdx Endpoint Number. + * @retval None + */ +TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_kind(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal |= USB_EP_KIND; + regVal &= USB_EPREG_MASK; + regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; + pcd_set_endpoint(USBx, bEpIdx, regVal); +} + +TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_ep_kind(USB_TypeDef * USBx, uint32_t bEpIdx) { + uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); + regVal &= USB_EPKIND_MASK; + regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; + pcd_set_endpoint(USBx, bEpIdx, regVal); +} + +// This checks if the device has "LPM" +#if defined(USB_ISTR_L1REQ) +#define USB_ISTR_L1REQ_FORCED (USB_ISTR_L1REQ) +#else +#define USB_ISTR_L1REQ_FORCED ((uint16_t)0x0000U) +#endif + +#define USB_ISTR_ALL_EVENTS (USB_ISTR_PMAOVR | USB_ISTR_ERR | USB_ISTR_WKUP | USB_ISTR_SUSP | \ + USB_ISTR_RESET | USB_ISTR_SOF | USB_ISTR_ESOF | USB_ISTR_L1REQ_FORCED ) + +// Number of endpoints in hardware +// TODO should use TUP_DCD_ENDPOINT_MAX +#define STFSDEV_EP_COUNT (8u) + +#endif /* PORTABLE_ST_STM32F0_DCD_STM32F0_FSDEV_PVT_ST_H_ */ diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h deleted file mode 100644 index 15de95d23..000000000 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev_pvt_st.h +++ /dev/null @@ -1,543 +0,0 @@ -/* - * Copyright(c) 2016 STMicroelectronics - * Copyright(c) N Conrad - * Copyright (c) 2019 Ha Thach (tinyusb.org) - * - * Redistribution and use in source and binary forms, with or without modification, - * are permitted provided that the following conditions are met: - * 1. Redistributions of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of its contributors - * may be used to endorse or promote products derived from this software - * without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE - * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR - * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, - * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * This file is part of the TinyUSB stack. - */ - -// This file contains source copied from ST's HAL, and thus should have their copyright statement. - -// FSDEV_PMA_SIZE is PMA buffer size in bytes. -// On 512-byte devices, access with a stride of two words (use every other 16-bit address) -// On 1024-byte devices, access with a stride of one word (use every 16-bit address) - -#ifndef PORTABLE_ST_STM32F0_DCD_STM32F0_FSDEV_PVT_ST_H_ -#define PORTABLE_ST_STM32F0_DCD_STM32F0_FSDEV_PVT_ST_H_ - -#if CFG_TUSB_MCU == OPT_MCU_STM32F0 - #include "stm32f0xx.h" - #define FSDEV_PMA_SIZE (1024u) - // F0x2 models are crystal-less - // All have internal D+ pull-up - // 070RB: 2 x 16 bits/word memory LPM Support, BCD Support - // PMA dedicated to USB (no sharing with CAN) - -#elif CFG_TUSB_MCU == OPT_MCU_STM32F1 - #include "stm32f1xx.h" - #define FSDEV_PMA_SIZE (512u) - // NO internal Pull-ups - // *B, and *C: 2 x 16 bits/word - - // F1 names this differently from the rest - #define USB_CNTR_LPMODE USB_CNTR_LP_MODE - -#elif defined(STM32F302xB) || defined(STM32F302xC) || \ - defined(STM32F303xB) || defined(STM32F303xC) || \ - defined(STM32F373xC) - #include "stm32f3xx.h" - #define FSDEV_PMA_SIZE (512u) - // NO internal Pull-ups - // *B, and *C: 1 x 16 bits/word - // PMA dedicated to USB (no sharing with CAN) - -#elif defined(STM32F302x6) || defined(STM32F302x8) || \ - defined(STM32F302xD) || defined(STM32F302xE) || \ - defined(STM32F303xD) || defined(STM32F303xE) - #include "stm32f3xx.h" - #define FSDEV_PMA_SIZE (1024u) - // NO internal Pull-ups - // *6, *8, *D, and *E: 2 x 16 bits/word LPM Support - // When CAN clock is enabled, USB can use first 768 bytes ONLY. - -#elif CFG_TUSB_MCU == OPT_MCU_STM32L0 - #include "stm32l0xx.h" - #define FSDEV_PMA_SIZE (1024u) - -#elif CFG_TUSB_MCU == OPT_MCU_STM32L1 - #include "stm32l1xx.h" - #define FSDEV_PMA_SIZE (512u) - -#elif CFG_TUSB_MCU == OPT_MCU_STM32G4 - #include "stm32g4xx.h" - #define FSDEV_PMA_SIZE (1024u) - -#elif CFG_TUSB_MCU == OPT_MCU_STM32G0 - #include "stm32g0xx.h" - #define FSDEV_BUS_32BIT - #define FSDEV_PMA_SIZE (2048u) - #undef USB_PMAADDR - #define USB_PMAADDR USB_DRD_PMAADDR - #define USB_TypeDef USB_DRD_TypeDef - #define EP0R CHEP0R - #define USB_EP_CTR_RX USB_EP_VTRX - #define USB_EP_CTR_TX USB_EP_VTTX - #define USB_EP_T_FIELD USB_CHEP_UTYPE - #define USB_EPREG_MASK USB_CHEP_REG_MASK - #define USB_EPTX_DTOGMASK USB_CHEP_TX_DTOGMASK - #define USB_EPRX_DTOGMASK USB_CHEP_RX_DTOGMASK - #define USB_EPTX_DTOG1 USB_CHEP_TX_DTOG1 - #define USB_EPTX_DTOG2 USB_CHEP_TX_DTOG2 - #define USB_EPRX_DTOG1 USB_CHEP_RX_DTOG1 - #define USB_EPRX_DTOG2 USB_CHEP_RX_DTOG2 - #define USB_EPRX_STAT USB_CH_RX_VALID - #define USB_EPKIND_MASK USB_EP_KIND_MASK - #define USB USB_DRD_FS - #define USB_CNTR_FRES USB_CNTR_USBRST - #define USB_CNTR_RESUME USB_CNTR_L2RES - #define USB_ISTR_EP_ID USB_ISTR_IDN - #define USB_EPADDR_FIELD USB_CHEP_ADDR - #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY - #define USB_CNTR_FSUSP USB_CNTR_SUSPEN - -#elif CFG_TUSB_MCU == OPT_MCU_STM32H5 - #include "stm32h5xx.h" - #define FSDEV_BUS_32BIT - #define FSDEV_PMA_SIZE (2048u) - #undef USB_PMAADDR - #define USB_PMAADDR USB_DRD_PMAADDR - #define USB_TypeDef USB_DRD_TypeDef - #define EP0R CHEP0R - #define USB_EP_CTR_RX USB_EP_VTRX - #define USB_EP_CTR_TX USB_EP_VTTX - #define USB_EP_T_FIELD USB_CHEP_UTYPE - #define USB_EPREG_MASK USB_CHEP_REG_MASK - #define USB_EPTX_DTOGMASK USB_CHEP_TX_DTOGMASK - #define USB_EPRX_DTOGMASK USB_CHEP_RX_DTOGMASK - #define USB_EPTX_DTOG1 USB_CHEP_TX_DTOG1 - #define USB_EPTX_DTOG2 USB_CHEP_TX_DTOG2 - #define USB_EPRX_DTOG1 USB_CHEP_RX_DTOG1 - #define USB_EPRX_DTOG2 USB_CHEP_RX_DTOG2 - #define USB_EPRX_STAT USB_CH_RX_VALID - #define USB_EPKIND_MASK USB_EP_KIND_MASK - #define USB USB_DRD_FS - #define USB_CNTR_FRES USB_CNTR_USBRST - #define USB_CNTR_RESUME USB_CNTR_L2RES - #define USB_ISTR_EP_ID USB_ISTR_IDN - #define USB_EPADDR_FIELD USB_CHEP_ADDR - #define USB_CNTR_LPMODE USB_CNTR_SUSPRDY - #define USB_CNTR_FSUSP USB_CNTR_SUSPEN - -#elif CFG_TUSB_MCU == OPT_MCU_STM32WB - #include "stm32wbxx.h" - #define FSDEV_PMA_SIZE (1024u) - /* ST provided header has incorrect value */ - #undef USB_PMAADDR - #define USB_PMAADDR USB1_PMAADDR - -#elif CFG_TUSB_MCU == OPT_MCU_STM32L4 - #include "stm32l4xx.h" - #define FSDEV_PMA_SIZE (1024u) - -#elif CFG_TUSB_MCU == OPT_MCU_STM32L5 - #include "stm32l5xx.h" - #define FSDEV_PMA_SIZE (1024u) - - #ifndef USB_PMAADDR - #define USB_PMAADDR (USB_BASE + (USB_PMAADDR_NS - USB_BASE_NS)) - #endif - -#else - #error You are using an untested or unimplemented STM32 variant. Please update the driver. - // This includes L1x0, L1x1, L1x2, L4x2 and L4x3, G1x1, G1x3, and G1x4 -#endif - -// For purposes of accessing the packet -#if ((FSDEV_PMA_SIZE) == 512u) - #define FSDEV_PMA_STRIDE (2u) -#elif ((FSDEV_PMA_SIZE) == 1024u) - #define FSDEV_PMA_STRIDE (1u) -#endif - -// The fsdev_bus_t type can be used for both register and PMA access necessities -// For type-safety create a new macro for the volatile address of PMAADDR -// The compiler should warn us if we cast it to a non-volatile type? -#ifdef FSDEV_BUS_32BIT -typedef uint32_t fsdev_bus_t; -static __IO uint32_t * const pma32 = (__IO uint32_t*)USB_PMAADDR; - -#else -typedef uint16_t fsdev_bus_t; -// Volatile is also needed to prevent the optimizer from changing access to 32-bit (as 32-bit access is forbidden) -static __IO uint16_t * const pma = (__IO uint16_t*)USB_PMAADDR; - -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t * pcd_btable_word_ptr(USB_TypeDef * USBx, size_t x) { - size_t total_word_offset = (((USBx)->BTABLE)>>1) + x; - total_word_offset *= FSDEV_PMA_STRIDE; - return &(pma[total_word_offset]); -} - -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_tx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) { - return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 1u); -} - -TU_ATTR_ALWAYS_INLINE static inline __IO uint16_t* pcd_ep_rx_cnt_ptr(USB_TypeDef * USBx, uint32_t bEpIdx) { - return pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 3u); -} -#endif - -/* Aligned buffer size according to hardware */ -TU_ATTR_ALWAYS_INLINE static inline uint16_t pcd_aligned_buffer_size(uint16_t size) { - /* The STM32 full speed USB peripheral supports only a limited set of - * buffer sizes given by the RX buffer entry format in the USB_BTABLE. */ - uint16_t blocksize = (size > 62) ? 32 : 2; - - // Round up while dividing requested size by blocksize - uint16_t numblocks = (size + blocksize - 1) / blocksize ; - - return numblocks * blocksize; -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wRegValue) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - __O uint32_t *reg = (__O uint32_t *)(USB_DRD_BASE + bEpIdx*4); - *reg = wRegValue; -#else - __O uint16_t *reg = (__O uint16_t *)((&USBx->EP0R) + bEpIdx*2u); - *reg = (uint16_t)wRegValue; -#endif -} - -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_endpoint(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - __I uint32_t *reg = (__I uint32_t *)(USB_DRD_BASE + bEpIdx*4); -#else - __I uint16_t *reg = (__I uint16_t *)((&USBx->EP0R) + bEpIdx*2u); -#endif - return *reg; -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_eptype(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wType) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= (uint32_t)USB_EP_T_MASK; - regVal |= wType; - regVal |= USB_EP_CTR_RX | USB_EP_CTR_TX; // These clear on write0, so must set high - pcd_set_endpoint(USBx, bEpIdx, regVal); -} - -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_eptype(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= USB_EP_T_FIELD; - return regVal; -} - -/** - * @brief Clears bit CTR_RX / CTR_TX in the endpoint register. - * @param USBx USB peripheral instance register address. - * @param bEpIdx Endpoint Number. - * @retval None - */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_rx_ep_ctr(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= USB_EPREG_MASK; - regVal &= ~USB_EP_CTR_RX; - regVal |= USB_EP_CTR_TX; // preserve CTR_TX (clears on writing 0) - pcd_set_endpoint(USBx, bEpIdx, regVal); -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_ep_ctr(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= USB_EPREG_MASK; - regVal &= ~USB_EP_CTR_TX; - regVal |= USB_EP_CTR_RX; // preserve CTR_RX (clears on writing 0) - pcd_set_endpoint(USBx, bEpIdx,regVal); -} - -/** - * @brief gets counter of the tx buffer. - * @param USBx USB peripheral instance register address. - * @param bEpIdx Endpoint Number. - * @retval Counter value - */ -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - return (pma32[2*bEpIdx] & 0x03FF0000) >> 16; -#else - __I uint16_t *regPtr = pcd_ep_tx_cnt_ptr(USBx, bEpIdx); - return *regPtr & 0x3ffU; -#endif -} - -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - /* WA: few cycles for RX PMA descriptor to update, otherwise doesn't return the correct value. - Note: required for G0, U5, H5 etc. - This workaround is ported from stm32h5xx_hal_pcd.h and fixes the issue when calling this function fast enough. - Reproduced with GCC ast optimization(O2/O3) and stm32h573i_dk with an high frequency. - Observed on Windows 10 where tud_task() is scheduled by interrupt handler. - */ - volatile uint32_t count = 10; // defined as PCD_RX_PMA_CNT in stm32 hal_driver - while (count > 0U) { - count--; - } - return (pma32[2*bEpIdx + 1] & 0x03FF0000) >> 16; -#else - __I uint16_t *regPtr = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); - return *regPtr & 0x3ffU; -#endif -} - -/** - * @brief Sets address in an endpoint register. - * @param USBx USB peripheral instance register address. - * @param bEpIdx Endpoint Number. - * @param bAddr Address. - * @retval None - */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t bAddr) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= USB_EPREG_MASK; - regVal |= bAddr; - regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; - pcd_set_endpoint(USBx, bEpIdx,regVal); -} - -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - return pma32[2*bEpIdx] & 0x0000FFFFu ; -#else - return *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 0u); -#endif -} - -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - return pma32[2*bEpIdx + 1] & 0x0000FFFFu; -#else - return *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 2u); -#endif -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - pma32[2*bEpIdx] = (pma32[2*bEpIdx] & 0xFFFF0000u) | (addr & 0x0000FFFCu); -#else - *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 0u) = addr; -#endif -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_address(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t addr) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & 0xFFFF0000u) | (addr & 0x0000FFFCu); -#else - *pcd_btable_word_ptr(USBx,(bEpIdx)*4u + 2u) = addr; -#endif -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - pma32[2*bEpIdx] = (pma32[2*bEpIdx] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); -#else - __IO uint16_t * reg = pcd_ep_tx_cnt_ptr(USBx, bEpIdx); - *reg = (uint16_t) (*reg & (uint16_t) ~0x3FFU) | (wCount & 0x3FFU); -#endif -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { -#ifdef FSDEV_BUS_32BIT - (void) USBx; - pma32[2*bEpIdx + 1] = (pma32[2*bEpIdx + 1] & ~0x03FF0000u) | ((wCount & 0x3FFu) << 16); -#else - __IO uint16_t * reg = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); - *reg = (uint16_t) (*reg & (uint16_t) ~0x3FFU) | (wCount & 0x3FFU); -#endif -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_blsize_num_blocks(USB_TypeDef * USBx, uint32_t rxtx_idx, - uint32_t blocksize, uint32_t numblocks) { - /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ -#ifdef FSDEV_BUS_32BIT - (void) USBx; - pma32[rxtx_idx] = (pma32[rxtx_idx] & 0x0000FFFFu) | (blocksize << 31) | ((numblocks - blocksize) << 26); -#else - __IO uint16_t *pdwReg = pcd_btable_word_ptr(USBx, rxtx_idx*2u + 1u); - *pdwReg = (blocksize << 15) | ((numblocks - blocksize) << 10); -#endif -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_bufsize(USB_TypeDef * USBx, uint32_t rxtx_idx, uint32_t wCount) { - wCount = pcd_aligned_buffer_size(wCount); - - /* We assume that the buffer size is already aligned to hardware requirements. */ - uint16_t blocksize = (wCount > 62) ? 1 : 0; - uint16_t numblocks = wCount / (blocksize ? 32 : 2); - - /* There should be no remainder in the above calculation */ - TU_ASSERT((wCount - (numblocks * (blocksize ? 32 : 2))) == 0, /**/); - - /* Encode into register. When BLSIZE==1, we need to subtract 1 block count */ - pcd_set_ep_blsize_num_blocks(USBx, rxtx_idx, blocksize, numblocks); -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { - pcd_set_ep_bufsize(USBx, 2*bEpIdx, wCount); -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_bufsize(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wCount) { - pcd_set_ep_bufsize(USBx, 2*bEpIdx + 1, wCount); -} - -/** - * @brief sets the status for tx transfer (bits STAT_TX[1:0]). - * @param USBx USB peripheral instance register address. - * @param bEpIdx Endpoint Number. - * @param wState new state - * @retval None - */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_tx_status(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wState) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= USB_EPTX_DTOGMASK; - - /* toggle first bit ? */ - if((USB_EPTX_DTOG1 & (wState))!= 0U) - { - regVal ^= USB_EPTX_DTOG1; - } - /* toggle second bit ? */ - if((USB_EPTX_DTOG2 & ((uint32_t)(wState)))!= 0U) - { - regVal ^= USB_EPTX_DTOG2; - } - - regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; - pcd_set_endpoint(USBx, bEpIdx, regVal); -} - -/** - * @brief sets the status for rx transfer (bits STAT_TX[1:0]) - * @param USBx USB peripheral instance register address. - * @param bEpIdx Endpoint Number. - * @param wState new state - * @retval None - */ - -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_rx_status(USB_TypeDef * USBx, uint32_t bEpIdx, uint32_t wState) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= USB_EPRX_DTOGMASK; - - /* toggle first bit ? */ - if((USB_EPRX_DTOG1 & wState)!= 0U) { - regVal ^= USB_EPRX_DTOG1; - } - /* toggle second bit ? */ - if((USB_EPRX_DTOG2 & wState)!= 0U) { - regVal ^= USB_EPRX_DTOG2; - } - - regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; - pcd_set_endpoint(USBx, bEpIdx, regVal); -} - -TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_status(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - return (regVal & USB_EPRX_STAT) >> (12u); -} - - -/** - * @brief Toggles DTOG_RX / DTOG_TX bit in the endpoint register. - * @param USBx USB peripheral instance register address. - * @param bEpIdx Endpoint Number. - * @retval None - */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_rx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= USB_EPREG_MASK; - regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX|USB_EP_DTOG_RX; - pcd_set_endpoint(USBx, bEpIdx, regVal); -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_tx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= USB_EPREG_MASK; - regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX|USB_EP_DTOG_TX; - pcd_set_endpoint(USBx, bEpIdx, regVal); -} - -/** - * @brief Clears DTOG_RX / DTOG_TX bit in the endpoint register. - * @param USBx USB peripheral instance register address. - * @param bEpIdx Endpoint Number. - * @retval None - */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_rx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - if((regVal & USB_EP_DTOG_RX) != 0) { - pcd_rx_dtog(USBx,bEpIdx); - } -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_tx_dtog(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - if((regVal & USB_EP_DTOG_TX) != 0) { - pcd_tx_dtog(USBx,bEpIdx); - } -} - -/** - * @brief set & clear EP_KIND bit. - * @param USBx USB peripheral instance register address. - * @param bEpIdx Endpoint Number. - * @retval None - */ -TU_ATTR_ALWAYS_INLINE static inline void pcd_set_ep_kind(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal |= USB_EP_KIND; - regVal &= USB_EPREG_MASK; - regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; - pcd_set_endpoint(USBx, bEpIdx, regVal); -} - -TU_ATTR_ALWAYS_INLINE static inline void pcd_clear_ep_kind(USB_TypeDef * USBx, uint32_t bEpIdx) { - uint32_t regVal = pcd_get_endpoint(USBx, bEpIdx); - regVal &= USB_EPKIND_MASK; - regVal |= USB_EP_CTR_RX|USB_EP_CTR_TX; - pcd_set_endpoint(USBx, bEpIdx, regVal); -} - -// This checks if the device has "LPM" -#if defined(USB_ISTR_L1REQ) -#define USB_ISTR_L1REQ_FORCED (USB_ISTR_L1REQ) -#else -#define USB_ISTR_L1REQ_FORCED ((uint16_t)0x0000U) -#endif - -#define USB_ISTR_ALL_EVENTS (USB_ISTR_PMAOVR | USB_ISTR_ERR | USB_ISTR_WKUP | USB_ISTR_SUSP | \ - USB_ISTR_RESET | USB_ISTR_SOF | USB_ISTR_ESOF | USB_ISTR_L1REQ_FORCED ) - -// Number of endpoints in hardware -// TODO should use TUP_DCD_ENDPOINT_MAX -#define STFSDEV_EP_COUNT (8u) - -#endif /* PORTABLE_ST_STM32F0_DCD_STM32F0_FSDEV_PVT_ST_H_ */ -- cgit v1.3.1 From fc54ad43b1ac89efa8853d69e836b16ddfe156fa Mon Sep 17 00:00:00 2001 From: hathach Date: Sun, 31 Mar 2024 21:53:12 +0700 Subject: move walkaround to dcd_ep_ctr_rx_handler(), increase cycle_count from 10 to 20 (40 cycle) --- .idea/runConfigurations/stlink.xml | 4 +-- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c | 51 +++++++++++++++++---------- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h | 10 ------ 3 files changed, 34 insertions(+), 31 deletions(-) (limited to 'src/portable') diff --git a/.idea/runConfigurations/stlink.xml b/.idea/runConfigurations/stlink.xml index babb8b463..c82f37d59 100644 --- a/.idea/runConfigurations/stlink.xml +++ b/.idea/runConfigurations/stlink.xml @@ -1,6 +1,6 @@ - - + + diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c index 5e54d0f56..7bf726f3f 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.c @@ -200,8 +200,7 @@ static bool dcd_read_packet_memory_ff(tu_fifo_t * ff, uint16_t src, uint16_t wNB // Inline helper //--------------------------------------------------------------------+ -TU_ATTR_ALWAYS_INLINE static inline xfer_ctl_t* xfer_ctl_ptr(uint32_t ep_addr) -{ +TU_ATTR_ALWAYS_INLINE static inline xfer_ctl_t* xfer_ctl_ptr(uint32_t ep_addr) { uint8_t epnum = tu_edpt_number(ep_addr); uint8_t dir = tu_edpt_dir(ep_addr); // Fix -Werror=null-dereference @@ -524,7 +523,7 @@ static void dcd_ep_ctr_tx_handler(uint32_t wIstr) xfer_ctl_t * xfer = xfer_ctl_ptr(ep_addr); if((xfer->total_len != xfer->queued_len)) /* TX not complete */ { - dcd_transmit_packet(xfer, EPindex); + dcd_transmit_packet(xfer, EPindex); } else /* TX Complete */ { @@ -533,10 +532,29 @@ static void dcd_ep_ctr_tx_handler(uint32_t wIstr) } // Handle CTR interrupt for the RX/OUT direction -// // Upon call, (wIstr & USB_ISTR_DIR) == 0U -static void dcd_ep_ctr_rx_handler(uint32_t wIstr) -{ +static void dcd_ep_ctr_rx_handler(uint32_t wIstr) { + #ifdef FSDEV_BUS_32BIT + /* https://www.st.com/resource/en/errata_sheet/es0561-stm32h503cbebkbrb-device-errata-stmicroelectronics.pdf + * From STM32H503 errata 2.15.1: Buffer description table update completes after CTR interrupt triggers + * Description: + * - During OUT transfers, the correct transfer interrupt (CTR) is triggered a little before the last USB SRAM accesses + * have completed. If the software responds quickly to the interrupt, the full buffer contents may not be correct. + * Workaround: + * - Software should ensure that a small delay is included before accessing the SRAM contents. This delay + * should be 800 ns in Full Speed mode and 6.4 μs in Low Speed mode + * - Since H5 can run up to 250Mhz -> 1 cycle = 4ns. Per errata, we need to wait 200 cycles. Though executing code + * also takes time, so we'll wait 40 cycles (count = 20). + * - Since Low Speed mode is not supported/popular, we will ignore it for now. + * + * Note: this errata also seems to apply to G0, U5, H5 etc. + */ + volatile uint32_t cycle_count = 20; // defined as PCD_RX_PMA_CNT in stm32 hal_driver + while (cycle_count > 0U) { + cycle_count--; // each count take 2 cycle (1 cycle for sub, 1 cycle for compare/jump) + } + #endif + uint32_t EPindex = wIstr & USB_ISTR_EP_ID; uint32_t wEPRegVal = pcd_get_endpoint(USB, EPindex); uint8_t ep_addr = wEPRegVal & USB_EPADDR_FIELD; @@ -545,8 +563,7 @@ static void dcd_ep_ctr_rx_handler(uint32_t wIstr) // Verify the CTR_RX bit is set. This was in the ST Micro code, // but I'm not sure it's actually necessary? - if((wEPRegVal & USB_EP_CTR_RX) == 0U) - { + if((wEPRegVal & USB_EP_CTR_RX) == 0U) { return; } @@ -633,26 +650,22 @@ static void dcd_ep_ctr_rx_handler(uint32_t wIstr) // (Based on the docs, it seems SETUP will always be accepted after CTR is cleared) if(ep_addr == 0u) { - // Always be prepared for a status packet... + // Always be prepared for a status packet... pcd_set_ep_rx_bufsize(USB, EPindex, CFG_TUD_ENDPOINT0_SIZE); pcd_clear_rx_ep_ctr(USB, EPindex); } } -static void dcd_ep_ctr_handler(void) -{ +static void dcd_ep_ctr_handler(void) { uint32_t wIstr; /* stay in loop while pending interrupts */ - while (((wIstr = USB->ISTR) & USB_ISTR_CTR) != 0U) - { - - if ((wIstr & USB_ISTR_DIR) == 0U) /* TX/IN */ - { + while (((wIstr = USB->ISTR) & USB_ISTR_CTR) != 0U) { + if ((wIstr & USB_ISTR_DIR) == 0U) { + /* TX/IN */ dcd_ep_ctr_tx_handler(wIstr); - } - else /* RX/OUT*/ - { + } else { + /* RX/OUT*/ dcd_ep_ctr_rx_handler(wIstr); } } diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h index 15de95d23..5de25765d 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h @@ -286,16 +286,6 @@ TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_tx_cnt(USB_TypeDef * USB TU_ATTR_ALWAYS_INLINE static inline uint32_t pcd_get_ep_rx_cnt(USB_TypeDef * USBx, uint32_t bEpIdx) { #ifdef FSDEV_BUS_32BIT (void) USBx; - /* WA: few cycles for RX PMA descriptor to update, otherwise doesn't return the correct value. - Note: required for G0, U5, H5 etc. - This workaround is ported from stm32h5xx_hal_pcd.h and fixes the issue when calling this function fast enough. - Reproduced with GCC ast optimization(O2/O3) and stm32h573i_dk with an high frequency. - Observed on Windows 10 where tud_task() is scheduled by interrupt handler. - */ - volatile uint32_t count = 10; // defined as PCD_RX_PMA_CNT in stm32 hal_driver - while (count > 0U) { - count--; - } return (pma32[2*bEpIdx + 1] & 0x03FF0000) >> 16; #else __I uint16_t *regPtr = pcd_ep_rx_cnt_ptr(USBx, bEpIdx); -- cgit v1.3.1 From 943a2a6db335d98843b73246fcce9aead0d38886 Mon Sep 17 00:00:00 2001 From: Wojciech Klimek Date: Sun, 31 Mar 2024 23:11:49 +0200 Subject: Support for STM32H503 MCU - added support for STM32H503RB on H503RB-NUCLEO board - modified H5 family.c file to allow portability between H503 and H565/H573 - redefined USB_DRD_BASE to USB_DRD_FS_BASE if STM32H503xx is used --- hw/bsp/stm32h5/boards/stm32h503nucleo/board.cmake | 8 ++ hw/bsp/stm32h5/boards/stm32h503nucleo/board.h | 142 ++++++++++++++++++++++ hw/bsp/stm32h5/boards/stm32h503nucleo/board.mk | 7 ++ hw/bsp/stm32h5/boards/stm32h563nucleo/board.h | 18 ++- hw/bsp/stm32h5/boards/stm32h573i_dk/board.h | 18 ++- hw/bsp/stm32h5/family.c | 19 +-- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h | 5 + 7 files changed, 199 insertions(+), 18 deletions(-) create mode 100644 hw/bsp/stm32h5/boards/stm32h503nucleo/board.cmake create mode 100644 hw/bsp/stm32h5/boards/stm32h503nucleo/board.h create mode 100644 hw/bsp/stm32h5/boards/stm32h503nucleo/board.mk (limited to 'src/portable') diff --git a/hw/bsp/stm32h5/boards/stm32h503nucleo/board.cmake b/hw/bsp/stm32h5/boards/stm32h503nucleo/board.cmake new file mode 100644 index 000000000..f0fb1d809 --- /dev/null +++ b/hw/bsp/stm32h5/boards/stm32h503nucleo/board.cmake @@ -0,0 +1,8 @@ +set(MCU_VARIANT stm32h503xx) +set(JLINK_DEVICE stm32h503rb) + +function(update_board TARGET) + target_compile_definitions(${TARGET} PUBLIC + STM32H503xx + ) +endfunction() diff --git a/hw/bsp/stm32h5/boards/stm32h503nucleo/board.h b/hw/bsp/stm32h5/boards/stm32h503nucleo/board.h new file mode 100644 index 000000000..96c126ab8 --- /dev/null +++ b/hw/bsp/stm32h5/boards/stm32h503nucleo/board.h @@ -0,0 +1,142 @@ +/* + * The MIT License (MIT) + * + * Copyright (c) 2020, Ha Thach (tinyusb.org) + * Copyright (c) 2023, HiFiPhile + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE + * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + * + * This file is part of the TinyUSB stack. + */ + +#ifndef BOARD_H_ +#define BOARD_H_ + +#ifdef __cplusplus +extern "C" { +#endif + +// LED +#define LED_PORT GPIOA +#define LED_PIN GPIO_PIN_5 +#define LED_STATE_ON 1 + +// Button +#define BUTTON_PORT GPIOA +#define BUTTON_PIN GPIO_PIN_0 +#define BUTTON_STATE_ACTIVE 0 + +// UART Enable for STLink VCOM +#define UART_DEV USART3 +#define UART_CLK_EN __USART3_CLK_ENABLE +#define UART_GPIO_PORT GPIOA +#define UART_GPIO_AF GPIO_AF13_USART3 + +#define UART_TX_PIN GPIO_PIN_3 +#define UART_RX_PIN GPIO_PIN_4 + +// //--------------------------------------------------------------------+ +// // RCC Clock +// //--------------------------------------------------------------------+ +static inline void board_clock_init(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {0}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; + + // Enable All GPIOs clocks + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); + __HAL_RCC_GPIOH_CLK_ENABLE(); + + /** Configure the main internal regulator output voltage + */ + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0); + + while(!__HAL_PWR_GET_FLAG(PWR_FLAG_VOSRDY)) {} + + /** Initializes the RCC Oscillators according to the specified parameters + * in the RCC_OscInitTypeDef structure. + */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48|RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSEState = RCC_HSE_ON; + RCC_OscInitStruct.HSI48State = RCC_HSI48_ON; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLL1_SOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = 12; + RCC_OscInitStruct.PLL.PLLN = 250; + RCC_OscInitStruct.PLL.PLLP = 2; + RCC_OscInitStruct.PLL.PLLQ = 2; + RCC_OscInitStruct.PLL.PLLR = 2; + RCC_OscInitStruct.PLL.PLLRGE = RCC_PLL1_VCIRANGE_1; + RCC_OscInitStruct.PLL.PLLVCOSEL = RCC_PLL1_VCORANGE_WIDE; + RCC_OscInitStruct.PLL.PLLFRACN = 0; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) + { + Error_Handler(); + } + + /** Initializes the CPU, AHB and APB buses clocks + */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK + |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2 + |RCC_CLOCKTYPE_PCLK3; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; + RCC_ClkInitStruct.APB3CLKDivider = RCC_HCLK_DIV1; + + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) + { + Error_Handler(); + } + + // Configure CRS clock source + __HAL_RCC_CRS_CLK_ENABLE(); + RCC_CRSInitTypeDef RCC_CRSInitStruct = {0}; + RCC_CRSInitStruct.Prescaler = RCC_CRS_SYNC_DIV1; + RCC_CRSInitStruct.Source = RCC_CRS_SYNC_SOURCE_USB; + RCC_CRSInitStruct.Polarity = RCC_CRS_SYNC_POLARITY_RISING; + RCC_CRSInitStruct.ReloadValue = __HAL_RCC_CRS_RELOADVALUE_CALCULATE(48000000, 1000); + RCC_CRSInitStruct.ErrorLimitValue = 34; + RCC_CRSInitStruct.HSI48CalibrationValue = 32; + HAL_RCCEx_CRSConfig(&RCC_CRSInitStruct); + + /* Select HSI48 as USB clock source */ + RCC_PeriphCLKInitTypeDef usb_clk = {0 }; + usb_clk.PeriphClockSelection = RCC_PERIPHCLK_USB; + usb_clk.UsbClockSelection = RCC_USBCLKSOURCE_HSI48; + HAL_RCCEx_PeriphCLKConfig(&usb_clk); + + /* Peripheral clock enable */ + __HAL_RCC_USB_CLK_ENABLE(); +} + +static inline void board_enable_vdd_usb(void) +{ + // USB in STM32H503RB does not require enabling VDD +} + +#ifdef __cplusplus +} +#endif + +#endif /* BOARD_H_ */ diff --git a/hw/bsp/stm32h5/boards/stm32h503nucleo/board.mk b/hw/bsp/stm32h5/boards/stm32h503nucleo/board.mk new file mode 100644 index 000000000..cf60098af --- /dev/null +++ b/hw/bsp/stm32h5/boards/stm32h503nucleo/board.mk @@ -0,0 +1,7 @@ +MCU_VARIANT = stm32h503xx + +CFLAGS += \ + -DSTM32H503xx + +# For flash-jlink target +JLINK_DEVICE = stm32h503rb diff --git a/hw/bsp/stm32h5/boards/stm32h563nucleo/board.h b/hw/bsp/stm32h5/boards/stm32h563nucleo/board.h index 8e849f5c8..ccbcbd8e2 100644 --- a/hw/bsp/stm32h5/boards/stm32h563nucleo/board.h +++ b/hw/bsp/stm32h5/boards/stm32h563nucleo/board.h @@ -54,10 +54,21 @@ extern "C" { //--------------------------------------------------------------------+ // RCC Clock //--------------------------------------------------------------------+ -static inline void SystemClock_Config(void) { +static inline void board_clock_init(void) +{ RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; + // Enable All GPIOs clocks + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); + __HAL_RCC_GPIOE_CLK_ENABLE(); + __HAL_RCC_GPIOG_CLK_ENABLE(); + __HAL_RCC_GPIOH_CLK_ENABLE(); + __HAL_RCC_GPIOI_CLK_ENABLE(); + /** Configure the main internal regulator output voltage */ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0); @@ -122,6 +133,11 @@ static inline void SystemClock_Config(void) { __HAL_RCC_USB_CLK_ENABLE(); } +static inline void board_enable_vdd_usb(void) +{ + /* Enable VDDUSB to power on USB peripheral */ + HAL_PWREx_EnableVddUSB(); +} #ifdef __cplusplus } #endif diff --git a/hw/bsp/stm32h5/boards/stm32h573i_dk/board.h b/hw/bsp/stm32h5/boards/stm32h573i_dk/board.h index 674cf8e2a..87bf2ac1a 100644 --- a/hw/bsp/stm32h5/boards/stm32h573i_dk/board.h +++ b/hw/bsp/stm32h5/boards/stm32h573i_dk/board.h @@ -54,10 +54,20 @@ extern "C" { //--------------------------------------------------------------------+ // RCC Clock //--------------------------------------------------------------------+ -static inline void SystemClock_Config(void) { +static inline void board_clock_init(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; + // Enable All GPIOs clocks + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); + __HAL_RCC_GPIOE_CLK_ENABLE(); + __HAL_RCC_GPIOG_CLK_ENABLE(); + __HAL_RCC_GPIOH_CLK_ENABLE(); + __HAL_RCC_GPIOI_CLK_ENABLE(); + /** Configure the main internal regulator output voltage */ HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1); @@ -108,6 +118,12 @@ static inline void SystemClock_Config(void) { __HAL_RCC_USB_CLK_ENABLE(); } +static inline void board_enable_vdd_usb(void) +{ + /* Enable VDDUSB to power on USB peripheral */ + HAL_PWREx_EnableVddUSB(); +} + #ifdef __cplusplus } #endif diff --git a/hw/bsp/stm32h5/family.c b/hw/bsp/stm32h5/family.c index ed1389a12..0ff09a259 100644 --- a/hw/bsp/stm32h5/family.c +++ b/hw/bsp/stm32h5/family.c @@ -59,23 +59,10 @@ UART_HandleTypeDef UartHandle; void board_init(void) { HAL_Init(); // required for HAL_RCC_Osc TODO check with freeRTOS - SystemClock_Config(); // implemented in board.h + board_clock_init(); // implemented in board.h SystemCoreClockUpdate(); - // Enable All GPIOs clocks - __HAL_RCC_GPIOA_CLK_ENABLE(); - __HAL_RCC_GPIOB_CLK_ENABLE(); - __HAL_RCC_GPIOC_CLK_ENABLE(); - __HAL_RCC_GPIOD_CLK_ENABLE(); - __HAL_RCC_GPIOE_CLK_ENABLE(); - __HAL_RCC_GPIOG_CLK_ENABLE(); - __HAL_RCC_GPIOH_CLK_ENABLE(); - __HAL_RCC_GPIOI_CLK_ENABLE(); - - //__HAL_RCC_SYSCFG_CLK_ENABLE(); - //__HAL_RCC_PWR_CLK_ENABLE(); - - UART_CLK_EN(); + UART_CLK_EN(); #if CFG_TUSB_OS == OPT_OS_NONE // 1ms tick timer @@ -141,7 +128,7 @@ void board_init(void) { __HAL_RCC_USB_CLK_ENABLE(); /* Enable VDDUSB */ - HAL_PWREx_EnableVddUSB(); + board_enable_vdd_usb(); } //--------------------------------------------------------------------+ diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h index 5de25765d..8cedee5d1 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h @@ -115,6 +115,11 @@ #elif CFG_TUSB_MCU == OPT_MCU_STM32H5 #include "stm32h5xx.h" #define FSDEV_BUS_32BIT + + #ifdef STM32H503xx + #define USB_DRD_BASE USB_DRD_FS_BASE + #endif + #define FSDEV_PMA_SIZE (2048u) #undef USB_PMAADDR #define USB_PMAADDR USB_DRD_PMAADDR -- cgit v1.3.1 From 057278c0c6c159880e11f9b16de5735d8fc821ce Mon Sep 17 00:00:00 2001 From: Wojciech Klimek Date: Mon, 1 Apr 2024 14:51:46 +0200 Subject: Support for STM32H503 MCU - review changes Implemented changes suggested in the review: - restored original name of SystemClock_Config() function - some GPIO clocks are only enabled if macros are defined - moved GPIO clocks init back to family.c --- hw/bsp/stm32h5/boards/stm32h503nucleo/board.h | 15 ++++----------- hw/bsp/stm32h5/boards/stm32h563nucleo/board.h | 12 +----------- hw/bsp/stm32h5/boards/stm32h573i_dk/board.h | 12 +----------- hw/bsp/stm32h5/family.c | 19 ++++++++++++++++++- src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h | 2 +- 5 files changed, 25 insertions(+), 35 deletions(-) (limited to 'src/portable') diff --git a/hw/bsp/stm32h5/boards/stm32h503nucleo/board.h b/hw/bsp/stm32h5/boards/stm32h503nucleo/board.h index 96c126ab8..0651b2694 100644 --- a/hw/bsp/stm32h5/boards/stm32h503nucleo/board.h +++ b/hw/bsp/stm32h5/boards/stm32h503nucleo/board.h @@ -51,21 +51,14 @@ extern "C" { #define UART_TX_PIN GPIO_PIN_3 #define UART_RX_PIN GPIO_PIN_4 -// //--------------------------------------------------------------------+ -// // RCC Clock -// //--------------------------------------------------------------------+ -static inline void board_clock_init(void) +//--------------------------------------------------------------------+ +// RCC Clock +//--------------------------------------------------------------------+ +static inline void SystemClock_Config(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; - // Enable All GPIOs clocks - __HAL_RCC_GPIOA_CLK_ENABLE(); - __HAL_RCC_GPIOB_CLK_ENABLE(); - __HAL_RCC_GPIOC_CLK_ENABLE(); - __HAL_RCC_GPIOD_CLK_ENABLE(); - __HAL_RCC_GPIOH_CLK_ENABLE(); - /** Configure the main internal regulator output voltage */ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0); diff --git a/hw/bsp/stm32h5/boards/stm32h563nucleo/board.h b/hw/bsp/stm32h5/boards/stm32h563nucleo/board.h index ccbcbd8e2..df249242a 100644 --- a/hw/bsp/stm32h5/boards/stm32h563nucleo/board.h +++ b/hw/bsp/stm32h5/boards/stm32h563nucleo/board.h @@ -54,21 +54,11 @@ extern "C" { //--------------------------------------------------------------------+ // RCC Clock //--------------------------------------------------------------------+ -static inline void board_clock_init(void) +static inline void SystemClock_Config(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; - // Enable All GPIOs clocks - __HAL_RCC_GPIOA_CLK_ENABLE(); - __HAL_RCC_GPIOB_CLK_ENABLE(); - __HAL_RCC_GPIOC_CLK_ENABLE(); - __HAL_RCC_GPIOD_CLK_ENABLE(); - __HAL_RCC_GPIOE_CLK_ENABLE(); - __HAL_RCC_GPIOG_CLK_ENABLE(); - __HAL_RCC_GPIOH_CLK_ENABLE(); - __HAL_RCC_GPIOI_CLK_ENABLE(); - /** Configure the main internal regulator output voltage */ __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE0); diff --git a/hw/bsp/stm32h5/boards/stm32h573i_dk/board.h b/hw/bsp/stm32h5/boards/stm32h573i_dk/board.h index 87bf2ac1a..c58de13ee 100644 --- a/hw/bsp/stm32h5/boards/stm32h573i_dk/board.h +++ b/hw/bsp/stm32h5/boards/stm32h573i_dk/board.h @@ -54,20 +54,10 @@ extern "C" { //--------------------------------------------------------------------+ // RCC Clock //--------------------------------------------------------------------+ -static inline void board_clock_init(void) { +static inline void SystemClock_Config(void) { RCC_OscInitTypeDef RCC_OscInitStruct = {0}; RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; - // Enable All GPIOs clocks - __HAL_RCC_GPIOA_CLK_ENABLE(); - __HAL_RCC_GPIOB_CLK_ENABLE(); - __HAL_RCC_GPIOC_CLK_ENABLE(); - __HAL_RCC_GPIOD_CLK_ENABLE(); - __HAL_RCC_GPIOE_CLK_ENABLE(); - __HAL_RCC_GPIOG_CLK_ENABLE(); - __HAL_RCC_GPIOH_CLK_ENABLE(); - __HAL_RCC_GPIOI_CLK_ENABLE(); - /** Configure the main internal regulator output voltage */ HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1); diff --git a/hw/bsp/stm32h5/family.c b/hw/bsp/stm32h5/family.c index 0ff09a259..e4a9666b7 100644 --- a/hw/bsp/stm32h5/family.c +++ b/hw/bsp/stm32h5/family.c @@ -59,9 +59,26 @@ UART_HandleTypeDef UartHandle; void board_init(void) { HAL_Init(); // required for HAL_RCC_Osc TODO check with freeRTOS - board_clock_init(); // implemented in board.h + SystemClock_Config(); // implemented in board.h SystemCoreClockUpdate(); + // Enable All GPIOs clocks + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOD_CLK_ENABLE(); + __HAL_RCC_GPIOH_CLK_ENABLE(); + + #ifdef __HAL_RCC_GPIOE_CLK_ENABLE + __HAL_RCC_GPIOE_CLK_ENABLE(); + #endif + #ifdef __HAL_RCC_GPIOG_CLK_ENABLE + __HAL_RCC_GPIOE_CLK_ENABLE(); + #endif + #ifdef __HAL_RCC_GPIOI_CLK_ENABLE + __HAL_RCC_GPIOE_CLK_ENABLE(); + #endif + UART_CLK_EN(); #if CFG_TUSB_OS == OPT_OS_NONE diff --git a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h index 8cedee5d1..946ad2c7c 100644 --- a/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h +++ b/src/portable/st/stm32_fsdev/dcd_stm32_fsdev.h @@ -116,7 +116,7 @@ #include "stm32h5xx.h" #define FSDEV_BUS_32BIT - #ifdef STM32H503xx + #if !defined(USB_DRD_BASE) && defined(USB_DRD_FS_BASE) #define USB_DRD_BASE USB_DRD_FS_BASE #endif -- cgit v1.3.1 From bd2210b812cca0f56fc54ab9ebe3e48482baa653 Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 2 Apr 2024 12:36:00 +0700 Subject: always limit number of NAK per endpoint per usb frame to save cpu usage. Default to 1 NAK per endpoint --- examples/host/bare_api/src/tusb_config.h | 1 - examples/host/cdc_msc_hid/src/tusb_config.h | 1 - .../host/cdc_msc_hid_freertos/src/tusb_config.h | 1 - examples/host/hid_controller/src/tusb_config.h | 1 - examples/host/msc_file_explorer/src/tusb_config.h | 1 - src/portable/analog/max3421/hcd_max3421.c | 144 ++++++++------------- 6 files changed, 56 insertions(+), 93 deletions(-) (limited to 'src/portable') diff --git a/examples/host/bare_api/src/tusb_config.h b/examples/host/bare_api/src/tusb_config.h index d8e81aa82..432446e94 100644 --- a/examples/host/bare_api/src/tusb_config.h +++ b/examples/host/bare_api/src/tusb_config.h @@ -72,7 +72,6 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/examples/host/cdc_msc_hid/src/tusb_config.h b/examples/host/cdc_msc_hid/src/tusb_config.h index 8a56ebc2b..a59a0ffb9 100644 --- a/examples/host/cdc_msc_hid/src/tusb_config.h +++ b/examples/host/cdc_msc_hid/src/tusb_config.h @@ -72,7 +72,6 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/examples/host/cdc_msc_hid_freertos/src/tusb_config.h b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h index 7705be5c8..35de5ee50 100644 --- a/examples/host/cdc_msc_hid_freertos/src/tusb_config.h +++ b/examples/host/cdc_msc_hid_freertos/src/tusb_config.h @@ -77,7 +77,6 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/examples/host/hid_controller/src/tusb_config.h b/examples/host/hid_controller/src/tusb_config.h index f087a93cf..3ac591d8f 100644 --- a/examples/host/hid_controller/src/tusb_config.h +++ b/examples/host/hid_controller/src/tusb_config.h @@ -72,7 +72,6 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/examples/host/msc_file_explorer/src/tusb_config.h b/examples/host/msc_file_explorer/src/tusb_config.h index 05b9fa174..c798b4383 100644 --- a/examples/host/msc_file_explorer/src/tusb_config.h +++ b/examples/host/msc_file_explorer/src/tusb_config.h @@ -72,7 +72,6 @@ #if CFG_TUSB_MCU == OPT_MCU_RP2040 // #define CFG_TUH_RPI_PIO_USB 1 // use pio-usb as host controller // #define CFG_TUH_MAX3421 1 // use max3421 as host controller - // #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 3 // max. transfer attempts per frame // host roothub port is 1 if using either pio-usb or max3421 #if (defined(CFG_TUH_RPI_PIO_USB) && CFG_TUH_RPI_PIO_USB) || (defined(CFG_TUH_MAX3421) && CFG_TUH_MAX3421) diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 324638cb8..3eb3f796f 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -166,35 +166,17 @@ enum { DEFAULT_HIEN = HIRQ_CONDET_IRQ | HIRQ_FRAME_IRQ | HIRQ_HXFRDN_IRQ | HIRQ_RCVDAV_IRQ }; +enum { + MAX_NAK_DEFAULT = 1 // Number of NAK per endpoint per usb frame +}; + enum { EP_STATE_IDLE = 0, - EP_STATE_ATTEMPT1 = 1, // pending 1st attempt - #if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME - EP_STATE_ATTEMPT2 = 2, // don't change order - EP_STATE_ATTEMPT3 = 3, // need to be incrementable - EP_STATE_ATTEMPT4 = 4, - EP_STATE_ATTEMPT5 = 5, - EP_STATE_ATTEMPT6 = 6, - EP_STATE_ATTEMPT7 = 7, - EP_STATE_ATTEMPT8 = 8, - EP_STATE_ATTEMPT9 = 9, - EP_STATE_ATTEMPT10 = 10, - EP_STATE_SUSPENDED, // keep next behind last attempt - #endif EP_STATE_COMPLETE, - EP_STATE_QUANTITY // not used. only to get quantity. keep last + EP_STATE_ATTEMPT_1, // pending 1st attempt + EP_STATE_ATTEMPT_MAX = 15 }; -TU_VERIFY_STATIC(EP_STATE_QUANTITY <= 16, "no more than 16 states possible. ep->state has 4 bits"); - -#if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME - #define EP_STATE_ATTEMPT_QUANTITY (EP_STATE_SUSPENDED - 1) - TU_VERIFY_STATIC(CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME >= 1 && - CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME <= EP_STATE_ATTEMPT_QUANTITY, "unsupported attempt quantity"); -#else - #define EP_STATE_ATTEMPT_QUANTITY 1 -#endif - //--------------------------------------------------------------------+ // //--------------------------------------------------------------------+ @@ -223,6 +205,8 @@ typedef struct { TU_VERIFY_STATIC(sizeof(max3421_ep_t) == 12, "size is not correct"); typedef struct { + volatile uint16_t frame_count; + // cached register uint8_t sndbc; uint8_t hirq; @@ -232,17 +216,17 @@ typedef struct { uint8_t hxfr; atomic_flag busy; // busy transferring - volatile uint16_t frame_count; - - max3421_ep_t ep[CFG_TUH_MAX3421_ENDPOINT_TOTAL]; // [0] is reserved for addr0 - OSAL_MUTEX_DEF(spi_mutexdef); #if OSAL_MUTEX_REQUIRED + OSAL_MUTEX_DEF(spi_mutexdef); osal_mutex_t spi_mutex; #endif + + max3421_ep_t ep[CFG_TUH_MAX3421_ENDPOINT_TOTAL]; // [0] is reserved for addr0 } max3421_data_t; static max3421_data_t _hcd_data; +static uint8_t _max_nak = MAX_NAK_DEFAULT; // max NAK before giving up in a usb frame //--------------------------------------------------------------------+ // API: SPI transfer with MAX3421E @@ -332,7 +316,6 @@ static void fifo_write(uint8_t rhport, uint8_t reg, uint8_t const * buffer, uint tuh_max3421_spi_xfer_api(rhport, buffer, NULL, len); max3421_spi_unlock(rhport, in_isr); - } static void fifo_read(uint8_t rhport, uint8_t * buffer, uint16_t len, bool in_isr) { @@ -421,18 +404,22 @@ static void free_ep(uint8_t daddr) { } } +// Check if endpoint has an queued transfer +TU_ATTR_ALWAYS_INLINE static inline bool is_ep_pending(max3421_ep_t const * ep) { + uint8_t const state = ep->state; + return ep->packet_size && state >= EP_STATE_ATTEMPT_1 && state < EP_STATE_ATTEMPT_1 + _max_nak; +} + +// Find the next pending endpoint using round-robin scheduling, starting from next endpoint. +// return NULL if not found +// TODO respect interrupt endpoint's interval static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { - // search for next pending endpoint using round-robin scheduling - // if no other endpoint is pending and current endpoint is still pending, the current endpoint will be returned - // if no other endpoint is pending and current endpoint is not pending, NULL will be returned - // TODO maybe prioritisation control/interrupt/bulk/iso size_t const idx = (size_t) (cur_ep - _hcd_data.ep); // starting from next endpoint for (size_t i = idx + 1; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->state >= EP_STATE_ATTEMPT1 && ep->state <= EP_STATE_ATTEMPT_QUANTITY && ep->packet_size) { -// TU_LOG3("next pending i = %u\r\n", i); + if (is_ep_pending(ep)) { return ep; } } @@ -440,8 +427,7 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // wrap around including current endpoint for (size_t i = 0; i <= idx; i++) { max3421_ep_t* ep = &_hcd_data.ep[i]; - if (ep->state >= EP_STATE_ATTEMPT1 && ep->state <= EP_STATE_ATTEMPT_QUANTITY && ep->packet_size) { -// TU_LOG3("next pending i = %u\r\n", i); + if (is_ep_pending(ep)) { return ep; } } @@ -469,7 +455,9 @@ bool hcd_init(uint8_t rhport) { tuh_max3421_int_api(rhport, false); TU_LOG2_INT(sizeof(max3421_ep_t)); + TU_LOG2_INT(sizeof(atomic_flag)); TU_LOG2_INT(sizeof(max3421_data_t)); + TU_LOG2_INT(offsetof(max3421_data_t, ep)); tu_memclr(&_hcd_data, sizeof(_hcd_data)); _hcd_data.peraddr = 0xff; // invalid @@ -689,7 +677,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf ep->buf = buffer; ep->total_len = buflen; ep->xferred_len = 0; - ep->state = EP_STATE_ATTEMPT1; + ep->state = EP_STATE_ATTEMPT_1; if ( ep_num == 0 ) { ep->is_setup = 0; @@ -726,7 +714,7 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] ep->buf = (uint8_t*)(uintptr_t) setup_packet; ep->total_len = 8; ep->xferred_len = 0; - ep->state = EP_STATE_ATTEMPT1; + ep->state = EP_STATE_ATTEMPT_1; // carry out transfer if not busy if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { @@ -839,40 +827,24 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { break; case HRSL_NAK: - // TODO no retry for iso in current frame - // TODO retry limitation over all (not only per frame) if (ep_num == 0) { - // setup/control => retry immediately + // control endpoint -> retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); - #if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME - } else if (ep->state == CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME) { - // no more retry this frame if max. attempts are reached => suspend and retry it next frame - ep->state = EP_STATE_SUSPENDED; - - max3421_ep_t * next_ep = find_next_pending_ep(ep); - if (next_ep) { - // switch to next pending endpoint TODO could have issue with double buffered if not clear previously out data - xact_inout(rhport, next_ep, true, in_isr); - } else { - // no more pending => clear busy - atomic_flag_clear(&_hcd_data.busy); - } - #endif } else { - // another attempt - #if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME + if (ep->state < EP_STATE_ATTEMPT_MAX) { ep->state++; - #endif + } max3421_ep_t * next_ep = find_next_pending_ep(ep); if (ep == next_ep) { - // this endpoint is only one pending => retry immediately + // this endpoint is only one pending -> retry immediately hxfr_write(rhport, _hcd_data.hxfr, in_isr); } else if (next_ep) { // switch to next pending endpoint TODO could have issue with double buffered if not clear previously out data xact_inout(rhport, next_ep, true, in_isr); } else { - TU_ASSERT(false,); + // no more pending in this frame -> clear busy + atomic_flag_clear(&_hcd_data.busy); } } return; @@ -957,28 +929,24 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { if (hirq & HIRQ_FRAME_IRQ) { _hcd_data.frame_count++; - #if CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME - // endpoints retry or restart attempt next frame - for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { - max3421_ep_t * ep = &_hcd_data.ep[i]; - - // retry the endpoints that are suspended (NAK) last frame - if (ep->state == EP_STATE_SUSPENDED) { - // resume and retry suspended endpoint with attempt 1 - ep->state = EP_STATE_ATTEMPT1; - - if (ep->packet_size) { // first test packet_size before atomic_flag_test_and_set() - if (!atomic_flag_test_and_set(&_hcd_data.busy) ) { - // trigger endpoint to be retried - xact_inout(rhport, ep, true, in_isr); - } - } - } else if (ep->state > EP_STATE_ATTEMPT1 && ep->state <= CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME) { - // restart all other running/pending endpoints - ep->state = EP_STATE_ATTEMPT1; + max3421_ep_t* ep_retry = NULL; + + // reset all endpoints attempt counter + for (size_t i = 0; i < CFG_TUH_MAX3421_ENDPOINT_TOTAL; i++) { + max3421_ep_t* ep = &_hcd_data.ep[i]; + if (ep->packet_size && ep->state > EP_STATE_ATTEMPT_1) { + ep->state = EP_STATE_ATTEMPT_1; + + if (ep_retry == NULL) { + ep_retry = ep; } } - #endif + } + + // start usb transfer if not busy + if (ep_retry != NULL && !atomic_flag_test_and_set(&_hcd_data.busy)) { + xact_inout(rhport, ep_retry, true, in_isr); + } } if (hirq & HIRQ_CONDET_IRQ) { @@ -987,17 +955,17 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { // queue more transfer in handle_xfer_done() can cause hirq to be set again while external IRQ may not catch and/or // not call this handler again. So we need to loop until all IRQ are cleared - while ( hirq & (HIRQ_RCVDAV_IRQ | HIRQ_HXFRDN_IRQ) ) { - if ( hirq & HIRQ_RCVDAV_IRQ ) { + while (hirq & (HIRQ_RCVDAV_IRQ | HIRQ_HXFRDN_IRQ)) { + if (hirq & HIRQ_RCVDAV_IRQ) { uint8_t const ep_num = _hcd_data.hxfr & HXFR_EPNUM_MASK; - max3421_ep_t *ep = find_opened_ep(_hcd_data.peraddr, ep_num, 1); + max3421_ep_t* ep = find_opened_ep(_hcd_data.peraddr, ep_num, 1); uint8_t xact_len = 0; // RCVDAV_IRQ can trigger 2 times (dual buffered) - while ( hirq & HIRQ_RCVDAV_IRQ ) { + while (hirq & HIRQ_RCVDAV_IRQ) { uint8_t rcvbc = reg_read(rhport, RCVBC_ADDR, in_isr); xact_len = (uint8_t) tu_min16(rcvbc, ep->total_len - ep->xferred_len); - if ( xact_len ) { + if (xact_len) { fifo_read(rhport, ep->buf, xact_len, in_isr); ep->buf += xact_len; ep->xferred_len += xact_len; @@ -1008,12 +976,12 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { hirq = reg_read(rhport, HIRQ_ADDR, in_isr); } - if ( xact_len < ep->packet_size || ep->xferred_len >= ep->total_len ) { + if (xact_len < ep->packet_size || ep->xferred_len >= ep->total_len) { ep->state = EP_STATE_COMPLETE; } } - if ( hirq & HIRQ_HXFRDN_IRQ ) { + if (hirq & HIRQ_HXFRDN_IRQ) { hirq_write(rhport, HIRQ_HXFRDN_IRQ, in_isr); handle_xfer_done(rhport, in_isr); } -- cgit v1.3.1 From e802fe0677c901a444e7c9b5d67be2a1f400adee Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 2 Apr 2024 14:28:41 +0700 Subject: refactor: add hxfr per endpoint --- src/portable/analog/max3421/hcd_max3421.c | 100 +++++++++++++++--------------- src/tusb_option.h | 13 +--- 2 files changed, 52 insertions(+), 61 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 3eb3f796f..1b182e551 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -184,17 +184,21 @@ enum { typedef struct { uint8_t daddr; - struct TU_ATTR_PACKED { - uint8_t state : 4; - uint8_t is_setup : 1; // also bit 4 in HXFR reg (smaller code, no shift necessary) - uint8_t ep_dir : 1; // also bit 5 in HXFR reg (smaller code, no shift necessary) - uint8_t is_iso : 1; // also bit 6 in HXFR reg (smaller code, no shift necessary) - uint8_t data_toggle : 1; + union { ; + struct TU_ATTR_PACKED { + uint8_t ep_num : 4; + uint8_t is_setup : 1; + uint8_t is_out : 1; + uint8_t is_iso : 1; + }hxfr_bm; + + uint8_t hxfr; }; struct TU_ATTR_PACKED { - uint8_t ep_num : 4; - uint16_t packet_size : 12; + uint8_t state : 4; + uint8_t data_toggle : 1; + uint16_t packet_size : 11; }; uint16_t total_len; @@ -370,10 +374,11 @@ TU_ATTR_ALWAYS_INLINE static inline void sndbc_write(uint8_t rhport, uint8_t dat //--------------------------------------------------------------------+ static max3421_ep_t* find_ep_not_addr0(uint8_t daddr, uint8_t ep_num, uint8_t ep_dir) { + uint8_t const is_out = 1-ep_dir; for(size_t i=1; idaddr && ep_num == ep->ep_num && (ep_dir == ep->ep_dir || ep_num == 0)) { + // control endpoint is bi-direction (skip check) + if (daddr == ep->daddr && ep_num == ep->hxfr_bm.ep_num && (ep_num == 0 || is_out == ep->hxfr_bm.is_out)) { return ep; } } @@ -577,7 +582,6 @@ void hcd_device_close(uint8_t rhport, uint8_t dev_addr) { // Open an endpoint bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * ep_desc) { (void) rhport; - (void) daddr; uint8_t const ep_num = tu_edpt_number(ep_desc->bEndpointAddress); tusb_dir_t const ep_dir = tu_edpt_dir(ep_desc->bEndpointAddress); @@ -589,12 +593,9 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * e ep = allocate_ep(); TU_ASSERT(ep); ep->daddr = daddr; - ep->ep_num = (uint8_t) (ep_num & 0x0f); - ep->ep_dir = (ep_dir == TUSB_DIR_IN) ? 1 : 0; - } - - if ( TUSB_XFER_ISOCHRONOUS == ep_desc->bmAttributes.xfer ) { - ep->is_iso = 1; + ep->hxfr_bm.ep_num = (uint8_t) (ep_num & 0x0f); + ep->hxfr_bm.is_out = (ep_dir == TUSB_DIR_OUT) ? 1 : 0; + ep->hxfr_bm.is_iso = (TUSB_XFER_ISOCHRONOUS == ep_desc->bmAttributes.xfer) ? 1 : 0; } ep->packet_size = (uint16_t) (tu_edpt_packet_size(ep_desc) & 0x7ff); @@ -602,7 +603,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t daddr, tusb_desc_endpoint_t const * e return true; } -void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { +static void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { // Page 12: Programming BULK-OUT Transfers // TODO double buffered if (switch_ep) { @@ -618,12 +619,10 @@ void xact_out(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { fifo_write(rhport, SNDFIFO_ADDR, ep->buf, xact_len, in_isr); } sndbc_write(rhport, xact_len, in_isr); - - uint8_t const hxfr = (uint8_t ) (ep->ep_num | HXFR_OUT_NIN | (ep->is_iso ? HXFR_ISO : 0)); - hxfr_write(rhport, hxfr, in_isr); + hxfr_write(rhport, ep->hxfr, in_isr); } -void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { +static void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { // Page 13: Programming BULK-IN Transfers if (switch_ep) { peraddr_write(rhport, ep->daddr, in_isr); @@ -632,34 +631,36 @@ void xact_in(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { reg_write(rhport, HCTL_ADDR, hctl, in_isr); } - uint8_t const hxfr = (uint8_t) (ep->ep_num | (ep->is_iso ? HXFR_ISO : 0)); - hxfr_write(rhport, hxfr, in_isr); + hxfr_write(rhport, ep->hxfr, in_isr); +} + +static void xact_setup(uint8_t rhport, max3421_ep_t *ep, bool in_isr) { + peraddr_write(rhport, ep->daddr, in_isr); + fifo_write(rhport, SUDFIFO_ADDR, ep->buf, 8, in_isr); + hxfr_write(rhport, HXFR_SETUP, in_isr); } -TU_ATTR_ALWAYS_INLINE static inline -void xact_inout(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { - if (ep->ep_num == 0 ) { +static void xact_generic(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool in_isr) { + if (ep->hxfr_bm.ep_num == 0 ) { // setup - if (ep->is_setup) { - peraddr_write(rhport, ep->daddr, in_isr); - fifo_write(rhport, SUDFIFO_ADDR, ep->buf, 8, in_isr); - hxfr_write(rhport, HXFR_SETUP, in_isr); + if (ep->hxfr_bm.is_setup) { + xact_setup(rhport, ep, in_isr); return; } // status if (ep->buf == NULL || ep->total_len == 0) { - uint8_t const hxfr = HXFR_HS | (ep->ep_dir ? 0 : HXFR_OUT_NIN); + uint8_t const hxfr = HXFR_HS | (ep->hxfr_bm.is_out ? HXFR_OUT_NIN : 0); peraddr_write(rhport, ep->daddr, in_isr); hxfr_write(rhport, hxfr, in_isr); return; } } - if (ep->ep_dir) { - xact_in(rhport, ep, switch_ep, in_isr); - }else { + if (ep->hxfr_bm.is_out) { xact_out(rhport, ep, switch_ep, in_isr); + }else { + xact_in(rhport, ep, switch_ep, in_isr); } } @@ -672,21 +673,21 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf TU_VERIFY(ep); // control transfer can switch direction - ep->ep_dir = ep_dir ? 1u : 0u; + ep->hxfr_bm.is_out = ep_dir ? 0u : 1u; ep->buf = buffer; ep->total_len = buflen; ep->xferred_len = 0; ep->state = EP_STATE_ATTEMPT_1; - if ( ep_num == 0 ) { - ep->is_setup = 0; + if (ep_num == 0) { + ep->hxfr_bm.is_setup = 0; ep->data_toggle = 1; } // carry out transfer if not busy - if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { - xact_inout(rhport, ep, true, false); + if (!atomic_flag_test_and_set(&_hcd_data.busy)) { + xact_generic(rhport, ep, true, false); } return true; @@ -709,16 +710,16 @@ bool hcd_setup_send(uint8_t rhport, uint8_t daddr, uint8_t const setup_packet[8] max3421_ep_t* ep = find_opened_ep(daddr, 0, 0); TU_ASSERT(ep); - ep->ep_dir = 0; - ep->is_setup = 1; + ep->hxfr_bm.is_out = 1; + ep->hxfr_bm.is_setup = 1; ep->buf = (uint8_t*)(uintptr_t) setup_packet; ep->total_len = 8; ep->xferred_len = 0; ep->state = EP_STATE_ATTEMPT_1; // carry out transfer if not busy - if ( !atomic_flag_test_and_set(&_hcd_data.busy) ) { - xact_inout(rhport, ep, true, false); + if (!atomic_flag_test_and_set(&_hcd_data.busy)) { + xact_setup(rhport, ep, false); } return true; @@ -783,10 +784,11 @@ static void handle_connect_irq(uint8_t rhport, bool in_isr) { } static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t result, uint8_t hrsl, bool in_isr) { - uint8_t const ep_addr = tu_edpt_addr(ep->ep_num, ep->ep_dir); + uint8_t const ep_dir = 1-ep->hxfr_bm.is_out; + uint8_t const ep_addr = tu_edpt_addr(ep->hxfr_bm.ep_num, ep_dir); // save data toggle - if (ep->ep_dir) { + if (ep_dir) { ep->data_toggle = (hrsl & HRSL_RCVTOGRD) ? 1u : 0u; }else { ep->data_toggle = (hrsl & HRSL_SNDTOGRD) ? 1u : 0u; @@ -798,7 +800,7 @@ static void xfer_complete_isr(uint8_t rhport, max3421_ep_t *ep, xfer_result_t re // Find next pending endpoint max3421_ep_t * next_ep = find_next_pending_ep(ep); if (next_ep) { - xact_inout(rhport, next_ep, true, in_isr); + xact_generic(rhport, next_ep, true, in_isr); }else { // no more pending atomic_flag_clear(&_hcd_data.busy); @@ -841,7 +843,7 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { hxfr_write(rhport, _hcd_data.hxfr, in_isr); } else if (next_ep) { // switch to next pending endpoint TODO could have issue with double buffered if not clear previously out data - xact_inout(rhport, next_ep, true, in_isr); + xact_generic(rhport, next_ep, true, in_isr); } else { // no more pending in this frame -> clear busy atomic_flag_clear(&_hcd_data.busy); @@ -945,7 +947,7 @@ void hcd_int_handler(uint8_t rhport, bool in_isr) { // start usb transfer if not busy if (ep_retry != NULL && !atomic_flag_test_and_set(&_hcd_data.busy)) { - xact_inout(rhport, ep_retry, true, in_isr); + xact_generic(rhport, ep_retry, true, in_isr); } } diff --git a/src/tusb_option.h b/src/tusb_option.h index 18cc8a82c..f90fb7026 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -34,7 +34,7 @@ #define TUSB_VERSION_MAJOR 0 #define TUSB_VERSION_MINOR 16 #define TUSB_VERSION_REVISION 0 -#define TUSB_VERSION_BUILD 1 +#define TUSB_VERSION_BUILD 2 #define TUSB_VERSION_NUMBER (TUSB_VERSION_MAJOR << 24 | TUSB_VERSION_MINOR << 16 | TUSB_VERSION_REVISION << 8 | TUSB_VERSION_BUILD) #define TUSB_VERSION_STRING TU_STRING(TUSB_VERSION_MAJOR) "." TU_STRING(TUSB_VERSION_MINOR) "." TU_STRING(TUSB_VERSION_REVISION) @@ -529,17 +529,6 @@ #define CFG_TUH_MAX3421 0 #endif -// MAX3421 Host max. transfer attempts per frame (except control and iso) -// retry quantity = (CFG_TUH_MAX3421_MAX_ATTEMPS_PER_FRAME - 1) -// 0 = endless retries. is default to keep compatibility -// => this may overload MCU with permanently repeating NAK interrupts -// => possible increased USB traffic, increased latencies, reduced data throughput -// a usual attempt quantity is 3 (reference: the book "USB Complete" by Jan Axelson) -#ifndef CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME - #define CFG_TUH_MAX3421_MAX_ATTEMPTS_PER_FRAME 0 -#endif - - //--------------------------------------------------------------------+ // TypeC Options (Default) //--------------------------------------------------------------------+ -- cgit v1.3.1 From 7d3d60f96de3f6e15291c9302463c294e2dc98de Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 2 Apr 2024 16:38:40 +0700 Subject: add hcd_configure() to change max NAK dynamically --- src/host/hcd.h | 2 +- src/host/usbh.c | 13 ++++++++----- src/host/usbh.h | 14 ++++++++++++-- src/portable/analog/max3421/hcd_max3421.c | 17 +++++++++++------ src/tusb_option.h | 1 - 5 files changed, 32 insertions(+), 15 deletions(-) (limited to 'src/portable') diff --git a/src/host/hcd.h b/src/host/hcd.h index d5804c608..5547c7cc5 100644 --- a/src/host/hcd.h +++ b/src/host/hcd.h @@ -125,7 +125,7 @@ bool hcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) TU_ATTR_W //--------------------------------------------------------------------+ // optional hcd configuration, called by tuh_configure() -bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) TU_ATTR_WEAK; +bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param); // Initialize controller to host mode bool hcd_init(uint8_t rhport); diff --git a/src/host/usbh.c b/src/host/usbh.c index 05091736e..aa0603d47 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -52,6 +52,13 @@ TU_ATTR_WEAK bool hcd_deinit(uint8_t rhport) { return false; } +TU_ATTR_WEAK bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { + (void) rhport; + (void) cfg_id; + (void) cfg_param; + return false; +} + TU_ATTR_WEAK void tuh_event_hook_cb(uint8_t rhport, uint32_t eventid, bool in_isr) { (void) rhport; (void) eventid; @@ -332,11 +339,7 @@ bool tuh_rhport_reset_bus(uint8_t rhport, bool active) { //--------------------------------------------------------------------+ bool tuh_configure(uint8_t rhport, uint32_t cfg_id, const void *cfg_param) { - if ( hcd_configure ) { - return hcd_configure(rhport, cfg_id, cfg_param); - } else { - return false; - } + return hcd_configure(rhport, cfg_id, cfg_param); } static void clear_device(usbh_device_t* dev) { diff --git a/src/host/usbh.h b/src/host/usbh.h index 0e31e80a7..57362c778 100644 --- a/src/host/usbh.h +++ b/src/host/usbh.h @@ -73,11 +73,21 @@ typedef struct { tusb_desc_interface_t desc; } tuh_itf_info_t; -// ConfigID for tuh_config() +// ConfigID for tuh_configure() enum { - TUH_CFGID_RPI_PIO_USB_CONFIGURATION = OPT_MCU_RP2040 << 8 // cfg_param: pio_usb_configuration_t + TUH_CFGID_INVALID = 0, + TUH_CFGID_RPI_PIO_USB_CONFIGURATION = 100, // cfg_param: pio_usb_configuration_t + TUH_CFGID_MAX3421 = 200, }; +typedef union { + // For TUH_CFGID_RPI_PIO_USB_CONFIGURATION use pio_usb_configuration_t + + struct { + uint8_t max_nak; + } max3421; +} tuh_configure_param_t; + //--------------------------------------------------------------------+ // APPLICATION CALLBACK //--------------------------------------------------------------------+ diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 1b182e551..12d80e0b5 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -30,6 +30,7 @@ #include #include "host/hcd.h" +#include "host/usbh.h" //--------------------------------------------------------------------+ // @@ -230,7 +231,9 @@ typedef struct { } max3421_data_t; static max3421_data_t _hcd_data; -static uint8_t _max_nak = MAX_NAK_DEFAULT; // max NAK before giving up in a usb frame + +// max NAK before giving up in a frame. 0 means infinite NAKs +static uint8_t _max_nak = MAX_NAK_DEFAULT; //--------------------------------------------------------------------+ // API: SPI transfer with MAX3421E @@ -409,10 +412,11 @@ static void free_ep(uint8_t daddr) { } } -// Check if endpoint has an queued transfer +// Check if endpoint has an queued transfer and not reach max NAK TU_ATTR_ALWAYS_INLINE static inline bool is_ep_pending(max3421_ep_t const * ep) { uint8_t const state = ep->state; - return ep->packet_size && state >= EP_STATE_ATTEMPT_1 && state < EP_STATE_ATTEMPT_1 + _max_nak; + return ep->packet_size && (state >= EP_STATE_ATTEMPT_1) && + (_max_nak == 0 || state < EP_STATE_ATTEMPT_1 + _max_nak); } // Find the next pending endpoint using round-robin scheduling, starting from next endpoint. @@ -447,10 +451,11 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // optional hcd configuration, called by tuh_configure() bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { (void) rhport; - (void) cfg_id; - (void) cfg_param; + TU_VERIFY(cfg_id == TUH_CFGID_MAX3421); - return false; + tuh_configure_param_t const* cfg = (tuh_configure_param_t const*) cfg_param; + _max_nak = cfg->max3421.max_nak; + return true; } // Initialize controller to host mode diff --git a/src/tusb_option.h b/src/tusb_option.h index f90fb7026..812074c44 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -144,7 +144,6 @@ #define OPT_MCU_RX72N 1402 ///< Renesas RX72N #define OPT_MCU_RAXXX 1403 ///< Renesas RAxxx families - // Mind Motion #define OPT_MCU_MM32F327X 1500 ///< Mind Motion MM32F327 -- cgit v1.3.1 From 172c9f70c74c541892006ff2bbfea818f40a235a Mon Sep 17 00:00:00 2001 From: hathach Date: Tue, 2 Apr 2024 16:55:49 +0700 Subject: clean up --- src/portable/analog/max3421/hcd_max3421.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 12d80e0b5..61a7e2703 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -173,8 +173,8 @@ enum { enum { EP_STATE_IDLE = 0, - EP_STATE_COMPLETE, - EP_STATE_ATTEMPT_1, // pending 1st attempt + EP_STATE_COMPLETE = 1, + EP_STATE_ATTEMPT_1 = 2, // pending 1st attempt EP_STATE_ATTEMPT_MAX = 15 }; @@ -465,7 +465,6 @@ bool hcd_init(uint8_t rhport) { tuh_max3421_int_api(rhport, false); TU_LOG2_INT(sizeof(max3421_ep_t)); - TU_LOG2_INT(sizeof(atomic_flag)); TU_LOG2_INT(sizeof(max3421_data_t)); TU_LOG2_INT(offsetof(max3421_data_t, ep)); @@ -873,7 +872,9 @@ static void handle_xfer_done(uint8_t rhport, bool in_isr) { if (ep_dir) { // IN transfer: fifo data is already received in RCVDAV IRQ - if ( hxfr_type & HXFR_HS ) { + + // mark control handshake as complete + if (hxfr_type & HXFR_HS) { ep->state = EP_STATE_COMPLETE; } -- cgit v1.3.1 From 8936096846f3b4e0f6d2193b5f8be74a94d003f9 Mon Sep 17 00:00:00 2001 From: Ha Thach Date: Tue, 2 Apr 2024 19:56:39 +0700 Subject: max3421 limit max nak --- src/portable/analog/max3421/hcd_max3421.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 61a7e2703..9e363506c 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -454,7 +454,7 @@ bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { TU_VERIFY(cfg_id == TUH_CFGID_MAX3421); tuh_configure_param_t const* cfg = (tuh_configure_param_t const*) cfg_param; - _max_nak = cfg->max3421.max_nak; + _max_nak = tu_max8(cfg->max3421.max_nak, EP_STATE_ATTEMPT_MAX-EP_STATE_ATTEMPT_1); return true; } -- cgit v1.3.1 From 9fb1fb90447fbbfdc3ca33c39cbd75bb807a7907 Mon Sep 17 00:00:00 2001 From: Ha Thach Date: Tue, 2 Apr 2024 20:39:06 +0700 Subject: correct max nak --- src/portable/analog/max3421/hcd_max3421.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 9e363506c..fa6d45d3e 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -454,7 +454,7 @@ bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { TU_VERIFY(cfg_id == TUH_CFGID_MAX3421); tuh_configure_param_t const* cfg = (tuh_configure_param_t const*) cfg_param; - _max_nak = tu_max8(cfg->max3421.max_nak, EP_STATE_ATTEMPT_MAX-EP_STATE_ATTEMPT_1); + _max_nak = tu_min8(cfg->max3421.max_nak, EP_STATE_ATTEMPT_MAX-EP_STATE_ATTEMPT_1); return true; } -- cgit v1.3.1 From f8dc3b97beae611c0a68ab50b960dd1922a66f5d Mon Sep 17 00:00:00 2001 From: Ha Thach Date: Tue, 2 Apr 2024 22:47:50 +0700 Subject: check cfg_param pointer --- src/portable/analog/max3421/hcd_max3421.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index fa6d45d3e..242c65501 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -451,7 +451,7 @@ static max3421_ep_t * find_next_pending_ep(max3421_ep_t * cur_ep) { // optional hcd configuration, called by tuh_configure() bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { (void) rhport; - TU_VERIFY(cfg_id == TUH_CFGID_MAX3421); + TU_VERIFY(cfg_id == TUH_CFGID_MAX3421 && cfg_param != NULL); tuh_configure_param_t const* cfg = (tuh_configure_param_t const*) cfg_param; _max_nak = tu_min8(cfg->max3421.max_nak, EP_STATE_ATTEMPT_MAX-EP_STATE_ATTEMPT_1); -- cgit v1.3.1 From 11722cc53393dff71a97b45e63309cb98c463b4b Mon Sep 17 00:00:00 2001 From: hathach Date: Wed, 3 Apr 2024 23:08:15 +0700 Subject: add note for sdk v2 and v3, also add check if allocreq failed --- src/portable/sony/cxd56/dcd_cxd56.c | 24 ++++++++++++++---------- 1 file changed, 14 insertions(+), 10 deletions(-) (limited to 'src/portable') diff --git a/src/portable/sony/cxd56/dcd_cxd56.c b/src/portable/sony/cxd56/dcd_cxd56.c index 83cd0718c..41814370e 100644 --- a/src/portable/sony/cxd56/dcd_cxd56.c +++ b/src/portable/sony/cxd56/dcd_cxd56.c @@ -103,19 +103,23 @@ static int _dcd_bind(FAR struct usbdevclass_driver_s *driver, FAR struct usbdev_ usbdcd_driver.ep[0] = dev->ep0; #ifdef EP_ALLOCREQ + // SDK v2 usbdcd_driver.req[0] = EP_ALLOCREQ(usbdcd_driver.ep[0]); - if (usbdcd_driver.req[0] != NULL) - { + if (usbdcd_driver.req[0] != NULL) { usbdcd_driver.req[0]->len = 64; usbdcd_driver.req[0]->buf = EP_ALLOCBUFFER(usbdcd_driver.ep[0], 64); - if (!usbdcd_driver.req[0]->buf) - { + if (!usbdcd_driver.req[0]->buf) { EP_FREEREQ(usbdcd_driver.ep[0], usbdcd_driver.req[0]); usbdcd_driver.req[0] = NULL; + return ENOMEM; } } #else - usbdcd_driver.req[0] = usbdev_allocreq(usbdcd_driver.ep[0],64); + // SDK v3 + usbdcd_driver.req[0] = usbdev_allocreq(usbdcd_driver.ep[0], 64); + if (usbdcd_driver.req[0] == NULL) { + return ENOMEM; + } #endif usbdcd_driver.req[0]->callback = usbdcd_ep0incomplete; @@ -301,17 +305,17 @@ bool dcd_edpt_open(uint8_t rhport, tusb_desc_endpoint_t const *p_endpoint_desc) usbdcd_driver.req[epnum] = NULL; #ifdef EP_ALLOCREQ + // sdk v2 usbdcd_driver.req[epnum] = EP_ALLOCREQ(usbdcd_driver.ep[epnum]); - if (usbdcd_driver.req[epnum] != NULL) - { + if (usbdcd_driver.req[epnum] != NULL) { usbdcd_driver.req[epnum]->len = ep_mps; } - else #else + // sdk v3 usbdcd_driver.req[epnum] = usbdev_allocreq(usbdcd_driver.ep[epnum], ep_mps); - if(usbdcd_driver.req[epnum] == NULL) #endif - { + + if(usbdcd_driver.req[epnum] == NULL) { return false; } -- cgit v1.3.1 From 7910cc298187327e05c43770b58eac528a4fecfa Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 4 Apr 2024 10:55:14 +0700 Subject: fix build with rp2040 + max3421 - forward MAX3421_HOST=1 from makefile to cmake - add feather_rp2040_max3421 board to run with ci for rp2040 + max3421 --- examples/build_system/make/make.mk | 1 + hw/bsp/rp2040/boards/feather_rp2040_max3421/board.cmake | 4 ++++ src/portable/analog/max3421/hcd_max3421.c | 13 ++++++------- 3 files changed, 11 insertions(+), 7 deletions(-) create mode 100644 hw/bsp/rp2040/boards/feather_rp2040_max3421/board.cmake (limited to 'src/portable') diff --git a/examples/build_system/make/make.mk b/examples/build_system/make/make.mk index e1113aa52..772befca4 100644 --- a/examples/build_system/make/make.mk +++ b/examples/build_system/make/make.mk @@ -113,6 +113,7 @@ CFLAGS += -DBOARD_$(BOARD_UPPER) ifeq (${MAX3421_HOST},1) SRC_C += src/portable/analog/max3421/hcd_max3421.c CFLAGS += -DCFG_TUH_MAX3421=1 + CMAKE_DEFSYM += -DMAX3421_HOST=1 endif # Log level is mapped to TUSB DEBUG option diff --git a/hw/bsp/rp2040/boards/feather_rp2040_max3421/board.cmake b/hw/bsp/rp2040/boards/feather_rp2040_max3421/board.cmake new file mode 100644 index 000000000..b8e5890f3 --- /dev/null +++ b/hw/bsp/rp2040/boards/feather_rp2040_max3421/board.cmake @@ -0,0 +1,4 @@ +set(PICO_BOARD adafruit_feather_rp2040) + +# Enable MAX3421E USB Host +set(MAX3421_HOST 1) diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 242c65501..76c1a150b 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -676,19 +676,18 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t daddr, uint8_t ep_addr, uint8_t * buf max3421_ep_t* ep = find_opened_ep(daddr, ep_num, ep_dir); TU_VERIFY(ep); - // control transfer can switch direction - ep->hxfr_bm.is_out = ep_dir ? 0u : 1u; + if (ep_num == 0) { + // control transfer can switch direction + ep->hxfr_bm.is_out = ep_dir ? 0 : 1; + ep->hxfr_bm.is_setup = 0; + ep->data_toggle = 1; + } ep->buf = buffer; ep->total_len = buflen; ep->xferred_len = 0; ep->state = EP_STATE_ATTEMPT_1; - if (ep_num == 0) { - ep->hxfr_bm.is_setup = 0; - ep->data_toggle = 1; - } - // carry out transfer if not busy if (!atomic_flag_test_and_set(&_hcd_data.busy)) { xact_generic(rhport, ep, true, false); -- cgit v1.3.1 From 93fb3b00debc613f631cb6ec848bfcb9231a325c Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 4 Apr 2024 12:51:07 +0700 Subject: fix build with gcc 11 --- src/portable/analog/max3421/hcd_max3421.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 76c1a150b..059f674cd 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -654,7 +654,7 @@ static void xact_generic(uint8_t rhport, max3421_ep_t *ep, bool switch_ep, bool // status if (ep->buf == NULL || ep->total_len == 0) { - uint8_t const hxfr = HXFR_HS | (ep->hxfr_bm.is_out ? HXFR_OUT_NIN : 0); + uint8_t const hxfr = (uint8_t) (HXFR_HS | (ep->hxfr & HXFR_OUT_NIN)); peraddr_write(rhport, ep->daddr, in_isr); hxfr_write(rhport, hxfr, in_isr); return; -- cgit v1.3.1 From caf2c5e0b75b72c0b0357ca364a76d70b5846bde Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 5 Apr 2024 17:04:33 +0700 Subject: reverted un-related file changes --- examples/device/cdc_msc_freertos/src/main.c | 51 ++++++++++++---------- hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk | 3 -- hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk | 3 -- hw/bsp/nrf/boards/pca10095/board.h | 4 +- hw/bsp/nrf/boards/pca10095/board.mk | 3 ++ hw/bsp/nrf/family.c | 1 + src/class/msc/msc_device.c | 2 +- src/class/video/video.h | 6 ++- src/common/tusb_debug.h | 3 +- src/common/tusb_fifo.c | 1 + src/host/usbh_pvt.h | 6 ++- src/portable/nordic/nrf5x/dcd_nrf5x.c | 8 +++- src/portable/ohci/ohci.h | 2 +- 13 files changed, 54 insertions(+), 39 deletions(-) (limited to 'src/portable') diff --git a/examples/device/cdc_msc_freertos/src/main.c b/examples/device/cdc_msc_freertos/src/main.c index 1dadc4513..e94e8eaec 100644 --- a/examples/device/cdc_msc_freertos/src/main.c +++ b/examples/device/cdc_msc_freertos/src/main.c @@ -52,7 +52,8 @@ #define USBD_STACK_SIZE (3*configMINIMAL_STACK_SIZE/2) * (CFG_TUSB_DEBUG ? 2 : 1) #endif -#define CDC_STACK_SZIE configMINIMAL_STACK_SIZE +#define CDC_STACK_SIZE configMINIMAL_STACK_SIZE +#define BLINKY_STACK_SIZE configMINIMAL_STACK_SIZE //--------------------------------------------------------------------+ // MACRO CONSTANT TYPEDEF PROTOTYPES @@ -69,21 +70,22 @@ enum { BLINK_SUSPENDED = 2500, }; -// static timer & task +// static task #if configSUPPORT_STATIC_ALLOCATION -StaticTimer_t blinky_tmdef; +StackType_t blinky_stack[BLINKY_STACK_SIZE]; +StaticTask_t blinky_taskdef; StackType_t usb_device_stack[USBD_STACK_SIZE]; StaticTask_t usb_device_taskdef; -StackType_t cdc_stack[CDC_STACK_SZIE]; +StackType_t cdc_stack[CDC_STACK_SIZE]; StaticTask_t cdc_taskdef; #endif -TimerHandle_t blinky_tm; +static uint32_t blink_interval_ms = BLINK_NOT_MOUNTED; -static void led_blinky_cb(TimerHandle_t xTimer); static void usb_device_task(void *param); +void led_blinking_task(void* param); void cdc_task(void *params); //--------------------------------------------------------------------+ @@ -94,22 +96,20 @@ int main(void) { board_init(); #if configSUPPORT_STATIC_ALLOCATION - // soft timer for blinky - blinky_tm = xTimerCreateStatic(NULL, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), true, NULL, led_blinky_cb, &blinky_tmdef); + // blinky task + xTaskCreateStatic(led_blinking_task, "blinky", BLINKY_STACK_SIZE, NULL, 1, blinky_stack, &blinky_taskdef); // Create a task for tinyusb device stack xTaskCreateStatic(usb_device_task, "usbd", USBD_STACK_SIZE, NULL, configMAX_PRIORITIES-1, usb_device_stack, &usb_device_taskdef); // Create CDC task - xTaskCreateStatic(cdc_task, "cdc", CDC_STACK_SZIE, NULL, configMAX_PRIORITIES-2, cdc_stack, &cdc_taskdef); + xTaskCreateStatic(cdc_task, "cdc", CDC_STACK_SIZE, NULL, configMAX_PRIORITIES - 2, cdc_stack, &cdc_taskdef); #else - blinky_tm = xTimerCreate(NULL, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), true, NULL, led_blinky_cb); + xTaskCreate(led_blinking_task, "blinky", BLINKY_STACK_SIZE, NULL, 1, NULL); xTaskCreate(usb_device_task, "usbd", USBD_STACK_SIZE, NULL, configMAX_PRIORITIES - 1, NULL); xTaskCreate(cdc_task, "cdc", CDC_STACK_SZIE, NULL, configMAX_PRIORITIES - 2, NULL); #endif - xTimerStart(blinky_tm, 0); - // skip starting scheduler (and return) for ESP32-S2 or ESP32-S3 #if !TU_CHECK_MCU(OPT_MCU_ESP32S2, OPT_MCU_ESP32S3) vTaskStartScheduler(); @@ -154,12 +154,12 @@ static void usb_device_task(void *param) { // Invoked when device is mounted void tud_mount_cb(void) { - xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_MOUNTED), 0); + blink_interval_ms = BLINK_MOUNTED; } // Invoked when device is unmounted void tud_umount_cb(void) { - xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), 0); + blink_interval_ms = BLINK_NOT_MOUNTED; } // Invoked when usb bus is suspended @@ -167,16 +167,12 @@ void tud_umount_cb(void) { // Within 7ms, device must draw an average of current less than 2.5 mA from bus void tud_suspend_cb(bool remote_wakeup_en) { (void) remote_wakeup_en; - xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_SUSPENDED), 0); + blink_interval_ms = BLINK_SUSPENDED; } // Invoked when usb bus is resumed void tud_resume_cb(void) { - if (tud_mounted()) { - xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_MOUNTED), 0); - } else { - xTimerChangePeriod(blinky_tm, pdMS_TO_TICKS(BLINK_NOT_MOUNTED), 0); - } + blink_interval_ms = tud_mounted() ? BLINK_MOUNTED : BLINK_NOT_MOUNTED; } //--------------------------------------------------------------------+ @@ -235,10 +231,17 @@ void tud_cdc_rx_cb(uint8_t itf) { //--------------------------------------------------------------------+ // BLINKING TASK //--------------------------------------------------------------------+ -static void led_blinky_cb(TimerHandle_t xTimer) { - (void) xTimer; +void led_blinking_task(void* param) { + (void) param; + static uint32_t start_ms = 0; static bool led_state = false; - board_led_write(led_state); - led_state = 1 - led_state; // toggle + while (1) { + // Blink every interval ms + vTaskDelay(blink_interval_ms / portTICK_PERIOD_MS); + start_ms += blink_interval_ms; + + board_led_write(led_state); + led_state = 1 - led_state; // toggle + } } diff --git a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk index f69700139..c4dc65b63 100644 --- a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk +++ b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2a4s/board.mk @@ -8,9 +8,6 @@ CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls -Wno-error=cast # All source paths should be relative to the top level. LD_FILE = $(MCU_DIR)/gcc/K32L2A41xxxxA_flash.ld -SRC_C += \ - $(MCU_DIR)/project_template/clock_config.c \ - # For flash-jlink target JLINK_DEVICE = K32L2A41xxxxA diff --git a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk index 82456b721..9cf36c500 100644 --- a/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk +++ b/hw/bsp/kinetis_k32l2/boards/frdm_k32l2b/board.mk @@ -8,9 +8,6 @@ CFLAGS += -Wno-error=unused-parameter -Wno-error=redundant-decls # All source paths should be relative to the top level. LD_FILE = $(MCU_DIR)/gcc/K32L2B31xxxxA_flash.ld -SRC_C += \ - $(MCU_DIR)/project_template/clock_config.c \ - # For flash-jlink target JLINK_DEVICE = K32L2B31xxxxA diff --git a/hw/bsp/nrf/boards/pca10095/board.h b/hw/bsp/nrf/boards/pca10095/board.h index 2a46e5422..846c2ee5b 100644 --- a/hw/bsp/nrf/boards/pca10095/board.h +++ b/hw/bsp/nrf/boards/pca10095/board.h @@ -42,8 +42,8 @@ #define BUTTON_STATE_ACTIVE 0 // UART -#define UART_RX_PIN 32 -#define UART_TX_PIN 33 +#define UART_RX_PIN 22 +#define UART_TX_PIN 20 // SPI for USB host shield // Pin is correct but not working probably due to signal incompatible (1.8V 3v3) with MAC3421E !? diff --git a/hw/bsp/nrf/boards/pca10095/board.mk b/hw/bsp/nrf/boards/pca10095/board.mk index 9c4edbafc..20580d619 100644 --- a/hw/bsp/nrf/boards/pca10095/board.mk +++ b/hw/bsp/nrf/boards/pca10095/board.mk @@ -2,6 +2,9 @@ CPU_CORE = cortex-m33 MCU_VARIANT = nrf5340_application CFLAGS += -DNRF5340_XXAA -DNRF5340_XXAA_APPLICATION +# enable max3421 host driver for this board +MAX3421_HOST = 1 + LD_FILE = hw/mcu/nordic/nrfx/mdk/nrf5340_xxaa_application.ld SRC_C += hw/mcu/nordic/nrfx/drivers/src/nrfx_usbreg.c diff --git a/hw/bsp/nrf/family.c b/hw/bsp/nrf/family.c index d6bb2d868..71c651f5f 100644 --- a/hw/bsp/nrf/family.c +++ b/hw/bsp/nrf/family.c @@ -76,6 +76,7 @@ enum { #define LFCLK_SRC_RC CLOCK_LFCLKSRC_SRC_LFRC #define VBUSDETECT_Msk USBREG_USBREGSTATUS_VBUSDETECT_Msk #define OUTPUTRDY_Msk USBREG_USBREGSTATUS_OUTPUTRDY_Msk + #define GPIOTE_IRQn GPIOTE1_IRQn #else #define LFCLK_SRC_RC CLOCK_LFCLKSRC_SRC_RC #define VBUSDETECT_Msk POWER_USBREGSTATUS_VBUSDETECT_Msk diff --git a/src/class/msc/msc_device.c b/src/class/msc/msc_device.c index 2589dcd2c..c145d86a6 100644 --- a/src/class/msc/msc_device.c +++ b/src/class/msc/msc_device.c @@ -203,7 +203,7 @@ uint8_t rdwr10_validate_cmd(msc_cbw_t const* cbw) //--------------------------------------------------------------------+ // Debug //--------------------------------------------------------------------+ -#if CFG_TUSB_DEBUG >= 2 +#if CFG_TUSB_DEBUG >= CFG_TUD_MSC_LOG_LEVEL TU_ATTR_UNUSED tu_static tu_lookup_entry_t const _msc_scsi_cmd_lookup[] = { diff --git a/src/class/video/video.h b/src/class/video/video.h index 3b511af96..b8a9b6369 100644 --- a/src/class/video/video.h +++ b/src/class/video/video.h @@ -369,6 +369,8 @@ typedef struct TU_ATTR_PACKED { uint8_t bCopyProtect; } tusb_desc_video_format_uncompressed_t; +TU_VERIFY_STATIC(sizeof(tusb_desc_video_format_uncompressed_t) == 27, "size is not correct"); + // Uncompressed payload specs: 3.1.2 frame descriptor #define tusb_desc_video_frame_uncompressed_nint_t(_nint) \ struct TU_ATTR_PACKED { \ @@ -382,7 +384,7 @@ typedef struct TU_ATTR_PACKED { uint32_t dwMinBitRate; \ uint32_t dwMaxBitRate; \ uint32_t dwMaxVideoFrameBufferSize; /* deprecated in 1.5 */ \ - uint32_t dwDefaultFrameInterval; \ + uint32_t dwDefaultFrameInterval; /* 100ns unit */\ uint8_t bFrameIntervalType; \ uint32_t dwFrameInterval[_nint]; \ } @@ -414,6 +416,8 @@ typedef struct TU_ATTR_PACKED { uint8_t bCopyProtect; } tusb_desc_video_format_mjpeg_t; +TU_VERIFY_STATIC(sizeof(tusb_desc_video_format_mjpeg_t) == 11, "size is not correct"); + // MJPEG payload specs: 3.1.2 frame descriptor (same as uncompressed) typedef tusb_desc_video_frame_uncompressed_t tusb_desc_video_frame_mjpeg_t; typedef tusb_desc_video_frame_uncompressed_1int_t tusb_desc_video_frame_mjpeg_1int_t; diff --git a/src/common/tusb_debug.h b/src/common/tusb_debug.h index 0f4dc93f3..2e9f1d9cd 100644 --- a/src/common/tusb_debug.h +++ b/src/common/tusb_debug.h @@ -60,6 +60,7 @@ void tu_print_mem(void const *buf, uint32_t count, uint8_t indent); static inline void tu_print_buf(uint8_t const* buf, uint32_t bufsize) { for(uint32_t i=0; i= 2 diff --git a/src/common/tusb_fifo.c b/src/common/tusb_fifo.c index d6c3db4ce..76696396b 100644 --- a/src/common/tusb_fifo.c +++ b/src/common/tusb_fifo.c @@ -224,6 +224,7 @@ static void _ff_push_n(tu_fifo_t* f, void const * app_buf, uint16_t n, uint16_t if (wrap_bytes > 0) _ff_push_const_addr(ff_buf, app_buf, wrap_bytes); } break; + default: break; } } diff --git a/src/host/usbh_pvt.h b/src/host/usbh_pvt.h index 46d13a907..95de915e9 100644 --- a/src/host/usbh_pvt.h +++ b/src/host/usbh_pvt.h @@ -35,7 +35,11 @@ extern "C" { #endif -#define TU_LOG_USBH(...) TU_LOG(CFG_TUH_LOG_LEVEL, __VA_ARGS__) +#define TU_LOG_USBH(...) TU_LOG(CFG_TUH_LOG_LEVEL, __VA_ARGS__) +#define TU_LOG_MEM_USBH(...) TU_LOG_MEM(CFG_TUH_LOG_LEVEL, __VA_ARGS__) +#define TU_LOG_BUF_USBH(...) TU_LOG_BUF(CFG_TUH_LOG_LEVEL, __VA_ARGS__) +#define TU_LOG_INT_USBH(...) TU_LOG_INT(CFG_TUH_LOG_LEVEL, __VA_ARGS__) +#define TU_LOG_HEX_USBH(...) TU_LOG_HEX(CFG_TUH_LOG_LEVEL, __VA_ARGS__) enum { USBH_EPSIZE_BULK_MAX = (TUH_OPT_HIGH_SPEED ? TUSB_EPSIZE_BULK_HS : TUSB_EPSIZE_BULK_FS) diff --git a/src/portable/nordic/nrf5x/dcd_nrf5x.c b/src/portable/nordic/nrf5x/dcd_nrf5x.c index cf9e5923b..80a285ef0 100644 --- a/src/portable/nordic/nrf5x/dcd_nrf5x.c +++ b/src/portable/nordic/nrf5x/dcd_nrf5x.c @@ -653,7 +653,11 @@ void dcd_int_handler(uint8_t rhport) if (NRF_USBD->EPOUTEN & USBD_EPOUTEN_ISOOUT_Msk) { iso_enabled = true; - xact_out_dma(EP_ISO_NUM); + // Transfer from endpoint to RAM only if data is not corrupted + if ((int_status & USBD_INTEN_USBEVENT_Msk) == 0 || + (NRF_USBD->EVENTCAUSE & USBD_EVENTCAUSE_ISOOUTCRC_Msk) == 0) { + xact_out_dma(EP_ISO_NUM); + } } // ISOIN: Notify client that data was transferred @@ -683,7 +687,7 @@ void dcd_int_handler(uint8_t rhport) { TU_LOG(3, "EVENTCAUSE = 0x%04lX\r\n", NRF_USBD->EVENTCAUSE); - enum { EVT_CAUSE_MASK = USBD_EVENTCAUSE_SUSPEND_Msk | USBD_EVENTCAUSE_RESUME_Msk | USBD_EVENTCAUSE_USBWUALLOWED_Msk }; + enum { EVT_CAUSE_MASK = USBD_EVENTCAUSE_SUSPEND_Msk | USBD_EVENTCAUSE_RESUME_Msk | USBD_EVENTCAUSE_USBWUALLOWED_Msk | USBD_EVENTCAUSE_ISOOUTCRC_Msk }; uint32_t const evt_cause = NRF_USBD->EVENTCAUSE & EVT_CAUSE_MASK; NRF_USBD->EVENTCAUSE = evt_cause; // clear interrupt diff --git a/src/portable/ohci/ohci.h b/src/portable/ohci/ohci.h index 4feefd771..94bad5df7 100644 --- a/src/portable/ohci/ohci.h +++ b/src/portable/ohci/ohci.h @@ -83,7 +83,7 @@ typedef struct TU_ATTR_ALIGNED(16) volatile uint32_t condition_code : 4; // Word 1 - volatile uint8_t* current_buffer_pointer; + uint8_t* volatile current_buffer_pointer; // Word 2 : next TD volatile uint32_t next; -- cgit v1.3.1 From 5ce458588498090204cdc7c3977c0fd48e00d710 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 5 Apr 2024 17:14:51 +0700 Subject: fix pre-commit format --- examples/build_system/make/cpu/cortex-m33-nodsp-nofp.mk | 2 +- hw/bsp/mcx/boards/frdmmcxa153/board.mk | 2 +- hw/bsp/mcx/boards/frdmmcxa153/clock_config.h | 2 +- hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c | 2 +- hw/bsp/mcx/family.c | 2 +- hw/bsp/mcx/family.cmake | 6 +++--- hw/bsp/mcx/family.mk | 4 ++-- src/portable/chipidea/ci_fs/ci_fs_mcx.h | 2 +- 8 files changed, 11 insertions(+), 11 deletions(-) (limited to 'src/portable') diff --git a/examples/build_system/make/cpu/cortex-m33-nodsp-nofp.mk b/examples/build_system/make/cpu/cortex-m33-nodsp-nofp.mk index f74f46d54..c65f24376 100644 --- a/examples/build_system/make/cpu/cortex-m33-nodsp-nofp.mk +++ b/examples/build_system/make/cpu/cortex-m33-nodsp-nofp.mk @@ -13,4 +13,4 @@ else ifeq ($(TOOLCHAIN),iar) endif -FREERTOS_PORTABLE_SRC ?= $(FREERTOS_PORTABLE_PATH)/ARM_CM33_NTZ/non_secure \ No newline at end of file +FREERTOS_PORTABLE_SRC ?= $(FREERTOS_PORTABLE_PATH)/ARM_CM33_NTZ/non_secure diff --git a/hw/bsp/mcx/boards/frdmmcxa153/board.mk b/hw/bsp/mcx/boards/frdmmcxa153/board.mk index a70a7dcef..cf6d9c0eb 100644 --- a/hw/bsp/mcx/boards/frdmmcxa153/board.mk +++ b/hw/bsp/mcx/boards/frdmmcxa153/board.mk @@ -6,7 +6,7 @@ CPU_CORE ?= cortex-m33-nodsp-nofp CFLAGS += \ -DCPU_MCXA153VLH \ -DCFG_TUSB_MCU=OPT_MCU_MCXA15 \ - + JLINK_DEVICE = MCXA153 PYOCD_TARGET = MCXA153 diff --git a/hw/bsp/mcx/boards/frdmmcxa153/clock_config.h b/hw/bsp/mcx/boards/frdmmcxa153/clock_config.h index 079d0d312..aae811052 100644 --- a/hw/bsp/mcx/boards/frdmmcxa153/clock_config.h +++ b/hw/bsp/mcx/boards/frdmmcxa153/clock_config.h @@ -4,7 +4,7 @@ * * SPDX-License-Identifier: BSD-3-Clause */ - + /*********************************************************************************************************************** * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. diff --git a/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c b/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c index b0e6de560..cc8f56e63 100644 --- a/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c +++ b/hw/bsp/mcx/boards/frdmmcxa153/pin_mux.c @@ -4,7 +4,7 @@ * * SPDX-License-Identifier: BSD-3-Clause */ - + /*********************************************************************************************************************** * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file * will be overwritten if the respective MCUXpresso Config Tools is used to update this file. diff --git a/hw/bsp/mcx/family.c b/hw/bsp/mcx/family.c index 74b84773d..96ae2fde3 100644 --- a/hw/bsp/mcx/family.c +++ b/hw/bsp/mcx/family.c @@ -151,7 +151,7 @@ void board_init(void) CLOCK_EnableClock(kCLOCK_Usb0Ram); CLOCK_EnableClock(kCLOCK_Usb0Fs); CLOCK_EnableUsbfsClock(); - + #endif #if PORT_SUPPORT_DEVICE(1) && (CFG_TUSB_MCU == OPT_MCU_MCXN9) diff --git a/hw/bsp/mcx/family.cmake b/hw/bsp/mcx/family.cmake index 078d13b9f..78490ec57 100644 --- a/hw/bsp/mcx/family.cmake +++ b/hw/bsp/mcx/family.cmake @@ -27,13 +27,13 @@ function(add_board_target BOARD_TARGET) ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_gpio.c ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_common_arm.c ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpuart.c - + # mcu ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_clock.c ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_reset.c ${SDK_DIR}/devices/${MCU_VARIANT}/system_${MCU_CORE}.c ) - + if (${FAMILY_MCUS} STREQUAL "MCXN9") target_sources(${BOARD_TARGET} PRIVATE ${SDK_DIR}/devices/${MCU_VARIANT}/drivers/fsl_lpflexcomm.c @@ -105,7 +105,7 @@ function(family_configure_example TARGET RTOS) elseif(${FAMILY_MCUS} STREQUAL "MCXA15") family_add_tinyusb(${TARGET} OPT_MCU_MCXA15 ${RTOS}) endif() - + target_sources(${TARGET}-tinyusb PUBLIC # TinyUSB: Port0 is chipidea FS, Port1 is chipidea HS ${TOP}/src/portable/chipidea/$ diff --git a/hw/bsp/mcx/family.mk b/hw/bsp/mcx/family.mk index 59170271c..3ee0efaf6 100644 --- a/hw/bsp/mcx/family.mk +++ b/hw/bsp/mcx/family.mk @@ -38,7 +38,7 @@ SRC_C += \ $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_gpio.c \ $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpuart.c \ $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_common_arm.c \ - + # fsl_lpflexcomm just needed for MCXN9 ifeq ($(MCU_VARIANT), MCXN947) @@ -54,7 +54,7 @@ ifeq ($(MCU_VARIANT), MCXA153) endif - + INC += \ $(TOP)/$(BOARD_PATH) \ diff --git a/src/portable/chipidea/ci_fs/ci_fs_mcx.h b/src/portable/chipidea/ci_fs/ci_fs_mcx.h index bf88df0f4..3f2b13323 100644 --- a/src/portable/chipidea/ci_fs/ci_fs_mcx.h +++ b/src/portable/chipidea/ci_fs/ci_fs_mcx.h @@ -36,7 +36,7 @@ #elif CFG_TUSB_MCU == OPT_MCU_MCXA15 #define CI_FS_REG(_port) ((ci_fs_regs_t*) USB0_BASE) #define USB0_IRQN USB0_IRQn - + #else #error "MCU is not supported" #endif -- cgit v1.3.1 From c97c3418c741a26666942e184ca514f5dbdafcfa Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 5 Apr 2024 20:31:55 +0700 Subject: minor update bsp --- examples/build_system/cmake/cpu/cortex-m23.cmake | 4 +- .../cmake/cpu/cortex-m33-nodsp-nofp.cmake | 2 +- examples/build_system/cmake/cpu/cortex-m33.cmake | 2 +- hw/bsp/mcx/boards/frdm_mcxa153/board.cmake | 3 - hw/bsp/mcx/boards/frdm_mcxa153/board.h | 20 +++-- hw/bsp/mcx/boards/frdm_mcxa153/board.mk | 2 +- hw/bsp/mcx/boards/frdm_mcxn947/board.cmake | 3 - hw/bsp/mcx/boards/frdm_mcxn947/board.mk | 2 +- hw/bsp/mcx/boards/mcxn947brk/board.cmake | 3 - hw/bsp/mcx/boards/mcxn947brk/board.mk | 2 +- hw/bsp/mcx/family.c | 92 ++++++++++------------ hw/bsp/mcx/family.cmake | 10 +++ hw/bsp/mcx/family.mk | 15 +--- src/portable/chipidea/ci_fs/ci_fs_mcx.h | 20 +++-- src/portable/chipidea/ci_fs/dcd_ci_fs.c | 2 +- 15 files changed, 81 insertions(+), 101 deletions(-) (limited to 'src/portable') diff --git a/examples/build_system/cmake/cpu/cortex-m23.cmake b/examples/build_system/cmake/cpu/cortex-m23.cmake index 3093dc99a..c7ce1d242 100644 --- a/examples/build_system/cmake/cpu/cortex-m23.cmake +++ b/examples/build_system/cmake/cpu/cortex-m23.cmake @@ -5,13 +5,13 @@ if (TOOLCHAIN STREQUAL "gcc") -mfloat-abi=soft ) - set(FREERTOS_PORT GCC_ARM_CM0 CACHE INTERNAL "") + set(FREERTOS_PORT GCC_ARM_CM23_NTZ_NONSECURE CACHE INTERNAL "") elseif (TOOLCHAIN STREQUAL "iar") set(TOOLCHAIN_COMMON_FLAGS --cpu cortex-m23 ) - set(FREERTOS_PORT IAR_ARM_CM0 CACHE INTERNAL "") + set(FREERTOS_PORT IAR_ARM_CM23_NTZ_NONSECURE CACHE INTERNAL "") endif () diff --git a/examples/build_system/cmake/cpu/cortex-m33-nodsp-nofp.cmake b/examples/build_system/cmake/cpu/cortex-m33-nodsp-nofp.cmake index 7946affbe..01e6b979a 100644 --- a/examples/build_system/cmake/cpu/cortex-m33-nodsp-nofp.cmake +++ b/examples/build_system/cmake/cpu/cortex-m33-nodsp-nofp.cmake @@ -12,6 +12,6 @@ elseif (TOOLCHAIN STREQUAL "iar") --cpu cortex-m33+nodsp ) - set(FREERTOS_PORT IAR_ARM_CM4F CACHE INTERNAL "") + set(FREERTOS_PORT IAR_ARM_CM33_NTZ_NONSECURE CACHE INTERNAL "") endif () diff --git a/examples/build_system/cmake/cpu/cortex-m33.cmake b/examples/build_system/cmake/cpu/cortex-m33.cmake index 7ebaf1748..94c29099d 100644 --- a/examples/build_system/cmake/cpu/cortex-m33.cmake +++ b/examples/build_system/cmake/cpu/cortex-m33.cmake @@ -14,6 +14,6 @@ elseif (TOOLCHAIN STREQUAL "iar") --fpu VFPv5-SP ) - set(FREERTOS_PORT IAR_ARM_CM4F CACHE INTERNAL "") + set(FREERTOS_PORT IAR_ARM_CM33_NTZ_NONSECURE CACHE INTERNAL "") endif () diff --git a/hw/bsp/mcx/boards/frdm_mcxa153/board.cmake b/hw/bsp/mcx/boards/frdm_mcxa153/board.cmake index acde3f46f..6a9a20e21 100644 --- a/hw/bsp/mcx/boards/frdm_mcxa153/board.cmake +++ b/hw/bsp/mcx/boards/frdm_mcxa153/board.cmake @@ -1,9 +1,6 @@ set(MCU_VARIANT MCXA153) set(MCU_CORE MCXA153) -set(FAMILY_MCUS MCXA15 CACHE INTERNAL "") -set(CMAKE_SYSTEM_PROCESSOR cortex-m33-nodsp-nofp CACHE INTERNAL "System Processor") - set(JLINK_DEVICE MCXA153_M33) set(PYOCD_TARGET MCXA153) set(NXPLINK_DEVICE MCXA153:MCXA153) diff --git a/hw/bsp/mcx/boards/frdm_mcxa153/board.h b/hw/bsp/mcx/boards/frdm_mcxa153/board.h index 02a452da5..e207d89d9 100644 --- a/hw/bsp/mcx/boards/frdm_mcxa153/board.h +++ b/hw/bsp/mcx/boards/frdm_mcxa153/board.h @@ -28,7 +28,7 @@ #define BOARD_H_ #ifdef __cplusplus - extern "C" { +extern "C" { #endif // LED @@ -38,29 +38,27 @@ #define LED_STATE_ON 0 // ISP button (Dummy, use unused pin - #define BUTTON_GPIO GPIO3 - #define BUTTON_CLK kCLOCK_GateGPIO3 - #define BUTTON_PIN 29 //sw2 - #define BUTTON_STATE_ACTIVE 0 +#define BUTTON_GPIO GPIO3 +#define BUTTON_CLK kCLOCK_GateGPIO3 +#define BUTTON_PIN 29 //sw2 +#define BUTTON_STATE_ACTIVE 0 // UART #define UART_DEV LPUART0 static inline void board_uart_init_clock(void) { - /* attach 12 MHz clock to LPUART0 (debug console) */ - CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u); - CLOCK_AttachClk(kFRO12M_to_LPUART0); + CLOCK_SetClockDiv(kCLOCK_DivLPUART0, 1u); + CLOCK_AttachClk(kFRO12M_to_LPUART0); - RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn); + RESET_PeripheralReset(kLPUART0_RST_SHIFT_RSTn); } - // XTAL #define XTAL0_CLK_HZ (24 * 1000 * 1000U) #ifdef __cplusplus - } +} #endif #endif diff --git a/hw/bsp/mcx/boards/frdm_mcxa153/board.mk b/hw/bsp/mcx/boards/frdm_mcxa153/board.mk index cf6d9c0eb..af8416d8e 100644 --- a/hw/bsp/mcx/boards/frdm_mcxa153/board.mk +++ b/hw/bsp/mcx/boards/frdm_mcxa153/board.mk @@ -2,7 +2,7 @@ MCU_VARIANT = MCXA153 MCU_CORE = MCXA153 PORT = 0 -CPU_CORE ?= cortex-m33-nodsp-nofp +CPU_CORE = cortex-m33-nodsp-nofp CFLAGS += \ -DCPU_MCXA153VLH \ -DCFG_TUSB_MCU=OPT_MCU_MCXA15 \ diff --git a/hw/bsp/mcx/boards/frdm_mcxn947/board.cmake b/hw/bsp/mcx/boards/frdm_mcxn947/board.cmake index a08d248f5..8c3280743 100644 --- a/hw/bsp/mcx/boards/frdm_mcxn947/board.cmake +++ b/hw/bsp/mcx/boards/frdm_mcxn947/board.cmake @@ -1,9 +1,6 @@ set(MCU_VARIANT MCXN947) set(MCU_CORE MCXN947_cm33_core0) -set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor") -set(FAMILY_MCUS MCXN9 CACHE INTERNAL "") - set(JLINK_DEVICE MCXN947_M33_0) set(PYOCD_TARGET MCXN947) set(NXPLINK_DEVICE MCXN947:MCXN947) diff --git a/hw/bsp/mcx/boards/frdm_mcxn947/board.mk b/hw/bsp/mcx/boards/frdm_mcxn947/board.mk index d90780996..22fefd79b 100644 --- a/hw/bsp/mcx/boards/frdm_mcxn947/board.mk +++ b/hw/bsp/mcx/boards/frdm_mcxn947/board.mk @@ -2,7 +2,7 @@ MCU_VARIANT = MCXN947 MCU_CORE = MCXN947_cm33_core0 PORT ?= 1 -CPU_CORE ?= cortex-m33 +CPU_CORE = cortex-m33 CFLAGS += \ -DCPU_MCXN947VDF_cm33_core0 \ -DCFG_TUSB_MCU=OPT_MCU_MCXN9 \ diff --git a/hw/bsp/mcx/boards/mcxn947brk/board.cmake b/hw/bsp/mcx/boards/mcxn947brk/board.cmake index a08d248f5..8c3280743 100644 --- a/hw/bsp/mcx/boards/mcxn947brk/board.cmake +++ b/hw/bsp/mcx/boards/mcxn947brk/board.cmake @@ -1,9 +1,6 @@ set(MCU_VARIANT MCXN947) set(MCU_CORE MCXN947_cm33_core0) -set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor") -set(FAMILY_MCUS MCXN9 CACHE INTERNAL "") - set(JLINK_DEVICE MCXN947_M33_0) set(PYOCD_TARGET MCXN947) set(NXPLINK_DEVICE MCXN947:MCXN947) diff --git a/hw/bsp/mcx/boards/mcxn947brk/board.mk b/hw/bsp/mcx/boards/mcxn947brk/board.mk index d90780996..22fefd79b 100644 --- a/hw/bsp/mcx/boards/mcxn947brk/board.mk +++ b/hw/bsp/mcx/boards/mcxn947brk/board.mk @@ -2,7 +2,7 @@ MCU_VARIANT = MCXN947 MCU_CORE = MCXN947_cm33_core0 PORT ?= 1 -CPU_CORE ?= cortex-m33 +CPU_CORE = cortex-m33 CFLAGS += \ -DCPU_MCXN947VDF_cm33_core0 \ -DCFG_TUSB_MCU=OPT_MCU_MCXN9 \ diff --git a/hw/bsp/mcx/family.c b/hw/bsp/mcx/family.c index 96ae2fde3..cc675a49d 100644 --- a/hw/bsp/mcx/family.c +++ b/hw/bsp/mcx/family.c @@ -33,6 +33,10 @@ #include "pin_mux.h" #include "clock_config.h" +//--------------------------------------------------------------------+ +// MACRO TYPEDEF CONSTANT ENUM +//--------------------------------------------------------------------+ + #ifdef BOARD_TUD_RHPORT #define PORT_SUPPORT_DEVICE(_n) (BOARD_TUD_RHPORT == _n) #else @@ -45,54 +49,50 @@ #define PORT_SUPPORT_HOST(_n) 0 #endif -//--------------------------------------------------------------------+ -// MACRO TYPEDEF CONSTANT ENUM -//--------------------------------------------------------------------+ - //--------------------------------------------------------------------+ // Forward USB interrupt events to TinyUSB IRQ Handler //--------------------------------------------------------------------+ #if CFG_TUSB_MCU == OPT_MCU_MCXN9 -void USB0_FS_IRQHandler(void) -{ +void USB0_FS_IRQHandler(void) { tud_int_handler(0); } -void USB1_HS_IRQHandler(void) -{ +void USB1_HS_IRQHandler(void) { tud_int_handler(1); } #elif CFG_TUSB_MCU == OPT_MCU_MCXA15 -void USB0_IRQHandler(void) -{ + +void USB0_IRQHandler(void) { tud_int_handler(0); } + #endif -void board_init(void) -{ +void board_init(void) { BOARD_InitPins(); BOARD_InitBootClocks(); CLOCK_SetupExtClocking(XTAL0_CLK_HZ); +#if CFG_TUSB_OS == OPT_OS_NONE // 1ms tick timer SysTick_Config(SystemCoreClock / 1000); - -#if CFG_TUSB_OS == OPT_OS_FREERTOS +#elif CFG_TUSB_OS == OPT_OS_FREERTOS // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher ) - NVIC_SetPriority(USB1_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY ); + #if CFG_TUSB_MCU == OPT_MCU_MCXN9 + NVIC_SetPriority(USB0_FS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + NVIC_SetPriority(USB1_HS_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + #else + NVIC_SetPriority(USB0_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY); + #endif #endif // LED CLOCK_EnableClock(LED_CLK); - gpio_pin_config_t led_config = { - kGPIO_DigitalOutput, - 0, - }; - GPIO_PinInit(LED_GPIO,LED_PIN, &led_config); + gpio_pin_config_t led_config = {kGPIO_DigitalOutput, 0}; + GPIO_PinInit(LED_GPIO, LED_PIN, &led_config); board_led_write(0); #ifdef NEOPIXEL_PIN @@ -110,7 +110,7 @@ void board_init(void) // Button #ifdef BUTTON_GPIO CLOCK_EnableClock(BUTTON_CLK); - gpio_pin_config_t const button_config = { kGPIO_DigitalInput, 0}; + gpio_pin_config_t const button_config = {kGPIO_DigitalInput, 0}; GPIO_PinInit(BUTTON_GPIO, BUTTON_PIN, &button_config); #endif @@ -125,33 +125,26 @@ void board_init(void) lpuart_config_t uart_config; LPUART_GetDefaultConfig(&uart_config); uart_config.baudRate_Bps = CFG_BOARD_UART_BAUDRATE; - uart_config.enableTx = true; - uart_config.enableRx = true; + uart_config.enableTx = true; + uart_config.enableRx = true; LPUART_Init(UART_DEV, &uart_config, 12000000u); #endif // USB VBUS /* PORT0 PIN22 configured as USB0_VBUS */ - - /* MCXA15 USB configurations */ -#if PORT_SUPPORT_DEVICE(0) && (CFG_TUSB_MCU == OPT_MCU_MCXA15) - - RESET_PeripheralReset(kUSB0_RST_SHIFT_RSTn); - CLOCK_EnableUsbfsClock(); - -#endif - - - /* MCXN9 USB configurations */ -#if PORT_SUPPORT_DEVICE(0) && (CFG_TUSB_MCU == OPT_MCU_MCXN9) +#if PORT_SUPPORT_DEVICE(0) // Port0 is Full Speed + #if CFG_TUSB_MCU == OPT_MCU_MCXA15 + RESET_PeripheralReset(kUSB0_RST_SHIFT_RSTn); + #elif CFG_TUSB_MCU == OPT_MCU_MCXN9 CLOCK_AttachClk(kCLK_48M_to_USB0); CLOCK_EnableClock(kCLOCK_Usb0Ram); CLOCK_EnableClock(kCLOCK_Usb0Fs); - CLOCK_EnableUsbfsClock(); + #endif + CLOCK_EnableUsbfsClock(); #endif #if PORT_SUPPORT_DEVICE(1) && (CFG_TUSB_MCU == OPT_MCU_MCXN9) @@ -213,9 +206,8 @@ void board_init(void) // Board porting API //--------------------------------------------------------------------+ -void board_led_write(bool state) -{ - GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); +void board_led_write(bool state) { + GPIO_PinWrite(LED_GPIO, LED_PIN, state ? LED_STATE_ON : (1 - LED_STATE_ON)); #ifdef NEOPIXEL_PIN if (state) { @@ -229,23 +221,21 @@ void board_led_write(bool state) #endif } -uint32_t board_button_read(void) -{ +uint32_t board_button_read(void) { #ifdef BUTTON_GPIO return BUTTON_STATE_ACTIVE == GPIO_PinRead(BUTTON_GPIO, BUTTON_PIN); #endif } -int board_uart_read(uint8_t* buf, int len) -{ - (void) buf; (void) len; +int board_uart_read(uint8_t* buf, int len) { + (void) buf; + (void) len; return 0; } -int board_uart_write(void const * buf, int len) -{ +int board_uart_write(void const* buf, int len) { #ifdef UART_DEV - LPUART_WriteBlocking(UART_DEV, (uint8_t const *) buf, len); + LPUART_WriteBlocking(UART_DEV, (uint8_t const*) buf, len); return len; #else (void) buf; (void) len; @@ -255,13 +245,13 @@ int board_uart_write(void const * buf, int len) #if CFG_TUSB_OS == OPT_OS_NONE volatile uint32_t system_ticks = 0; -void SysTick_Handler(void) -{ + +void SysTick_Handler(void) { system_ticks++; } -uint32_t board_millis(void) -{ +uint32_t board_millis(void) { return system_ticks; } + #endif diff --git a/hw/bsp/mcx/family.cmake b/hw/bsp/mcx/family.cmake index 78490ec57..c8591b569 100644 --- a/hw/bsp/mcx/family.cmake +++ b/hw/bsp/mcx/family.cmake @@ -11,6 +11,16 @@ set(CMSIS_DIR ${TOP}/lib/CMSIS_5) include(${CMAKE_CURRENT_LIST_DIR}/boards/${BOARD}/board.cmake) # toolchain set up +if (MCU_VARIANT STREQUAL "MCXA153") + set(CMAKE_SYSTEM_PROCESSOR cortex-m33-nodsp-nofp CACHE INTERNAL "System Processor") + set(FAMILY_MCUS MCXA15 CACHE INTERNAL "") +elseif (MCU_VARIANT STREQUAL "MCXN947") + set(CMAKE_SYSTEM_PROCESSOR cortex-m33 CACHE INTERNAL "System Processor") + set(FAMILY_MCUS MCXN9 CACHE INTERNAL "") +else() + message(FATAL_ERROR "MCU_VARIANT not supported") +endif() + set(CMAKE_TOOLCHAIN_FILE ${TOP}/examples/build_system/cmake/toolchain/arm_${TOOLCHAIN}.cmake) #------------------------------------ diff --git a/hw/bsp/mcx/family.mk b/hw/bsp/mcx/family.mk index 3ee0efaf6..58149fb8d 100644 --- a/hw/bsp/mcx/family.mk +++ b/hw/bsp/mcx/family.mk @@ -39,23 +39,16 @@ SRC_C += \ $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpuart.c \ $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_common_arm.c \ - -# fsl_lpflexcomm just needed for MCXN9 +# fsl_lpflexcomm for MCXN9 ifeq ($(MCU_VARIANT), MCXN947) - SRC_C += \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpflexcomm.c \ - + SRC_C += $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_lpflexcomm.c endif -# fsl_spc just needed for MCXNA15 +# fsl_spc for MCXNA15 ifeq ($(MCU_VARIANT), MCXA153) - SRC_C += \ - $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_spc.c \ - + SRC_C += $(SDK_DIR)/devices/$(MCU_VARIANT)/drivers/fsl_spc.c endif - - INC += \ $(TOP)/$(BOARD_PATH) \ $(TOP)/lib/CMSIS_5/CMSIS/Core/Include \ diff --git a/src/portable/chipidea/ci_fs/ci_fs_mcx.h b/src/portable/chipidea/ci_fs/ci_fs_mcx.h index 3f2b13323..4b93a03a7 100644 --- a/src/portable/chipidea/ci_fs/ci_fs_mcx.h +++ b/src/portable/chipidea/ci_fs/ci_fs_mcx.h @@ -30,29 +30,27 @@ #include "fsl_device_registers.h" #if CFG_TUSB_MCU == OPT_MCU_MCXN9 - #define CI_FS_REG(_port) ((ci_fs_regs_t*) USBFS0_BASE) - #define USB0_IRQN USB0_FS_IRQn + #define CI_FS_REG(_port) ((ci_fs_regs_t*) USBFS0_BASE) + #define CIFS_IRQN USB0_FS_IRQn #elif CFG_TUSB_MCU == OPT_MCU_MCXA15 - #define CI_FS_REG(_port) ((ci_fs_regs_t*) USB0_BASE) - #define USB0_IRQN USB0_IRQn + #define CI_FS_REG(_port) ((ci_fs_regs_t*) USB0_BASE) + #define CIFS_IRQN USB0_IRQn #else #error "MCU is not supported" #endif -#define CI_REG CI_FS_REG(0) +#define CI_REG CI_FS_REG(0) -void dcd_int_enable(uint8_t rhport) -{ +void dcd_int_enable(uint8_t rhport) { (void) rhport; - NVIC_EnableIRQ(USB0_IRQN); + NVIC_EnableIRQ(CIFS_IRQN); } -void dcd_int_disable(uint8_t rhport) -{ +void dcd_int_disable(uint8_t rhport) { (void) rhport; - NVIC_DisableIRQ(USB0_IRQN); + NVIC_DisableIRQ(CIFS_IRQN); } #endif diff --git a/src/portable/chipidea/ci_fs/dcd_ci_fs.c b/src/portable/chipidea/ci_fs/dcd_ci_fs.c index a68ecf8c9..02f813ab5 100644 --- a/src/portable/chipidea/ci_fs/dcd_ci_fs.c +++ b/src/portable/chipidea/ci_fs/dcd_ci_fs.c @@ -295,7 +295,7 @@ void dcd_init(uint8_t rhport) CI_REG->INT_EN = USB_INTEN_USBRSTEN_MASK; dcd_connect(rhport); - // NVIC_ClearPendingIRQ(USB0_IRQn); + // NVIC_ClearPendingIRQ(CIFS_IRQN); } void dcd_set_address(uint8_t rhport, uint8_t dev_addr) -- cgit v1.3.1 From e160366a1e3fc26242daf0e31c0d0fafcc51b83c Mon Sep 17 00:00:00 2001 From: HiFiPhile Date: Fri, 5 Apr 2024 19:12:28 +0200 Subject: dwc2: remove fifo free code. --- src/portable/synopsys/dwc2/dcd_dwc2.c | 43 ----------------------------------- 1 file changed, 43 deletions(-) (limited to 'src/portable') diff --git a/src/portable/synopsys/dwc2/dcd_dwc2.c b/src/portable/synopsys/dwc2/dcd_dwc2.c index cf8f3be50..8b13b0753 100644 --- a/src/portable/synopsys/dwc2/dcd_dwc2.c +++ b/src/portable/synopsys/dwc2/dcd_dwc2.c @@ -97,7 +97,6 @@ static uint16_t ep0_pending[2]; // Index determines direction as t // TX FIFO RAM allocation so far in words - RX FIFO size is readily available from dwc2->grxfsiz static uint16_t _allocated_fifo_words_tx; // TX FIFO size in words (IN EPs) -static bool _out_ep_closed; // Flag to check if RX FIFO size needs an update (reduce its size) // SOF enabling flag - required for SOF to not get disabled in ISR when SOF was enabled by static bool _sof_en; @@ -113,20 +112,6 @@ static inline uint16_t calc_grxfsiz(uint16_t max_ep_size, uint8_t ep_count) { return 15 + 2 * (max_ep_size / 4) + 2 * ep_count; } -static void update_grxfsiz(uint8_t rhport) { - dwc2_regs_t* dwc2 = DWC2_REG(rhport); - uint8_t const ep_count = _dwc2_controller[rhport].ep_count; - - // Determine largest EP size for RX FIFO - uint16_t max_epsize = 0; - for (uint8_t epnum = 0; epnum < ep_count; epnum++) { - max_epsize = tu_max16(max_epsize, xfer_status[epnum][TUSB_DIR_OUT].max_size); - } - - // Update size of RX FIFO - dwc2->grxfsiz = calc_grxfsiz(max_epsize, ep_count); -} - static bool fifo_alloc(uint8_t rhport, uint8_t ep_addr, uint16_t packet_size) { dwc2_regs_t* dwc2 = DWC2_REG(rhport); uint8_t const ep_count = _dwc2_controller[rhport].ep_count; @@ -268,7 +253,6 @@ static void bus_reset(uint8_t rhport) { uint8_t const ep_count = _dwc2_controller[rhport].ep_count; tu_memclr(xfer_status, sizeof(xfer_status)); - _out_ep_closed = false; _sof_en = false; @@ -791,26 +775,7 @@ bool dcd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t* ff, uint16_t } void dcd_edpt_close(uint8_t rhport, uint8_t ep_addr) { - dwc2_regs_t* dwc2 = DWC2_REG(rhport); - - uint8_t const epnum = tu_edpt_number(ep_addr); - uint8_t const dir = tu_edpt_dir(ep_addr); - edpt_disable(rhport, ep_addr, false); - - // Update max_size - xfer_status[epnum][dir].max_size = 0; // max_size = 0 marks a disabled EP - required for changing FIFO allocation - - if (dir == TUSB_DIR_IN) { - uint16_t const fifo_size = (dwc2->dieptxf[epnum - 1] & DIEPTXF_INEPTXFD_Msk) >> DIEPTXF_INEPTXFD_Pos; - uint16_t const fifo_start = (dwc2->dieptxf[epnum - 1] & DIEPTXF_INEPTXSA_Msk) >> DIEPTXF_INEPTXSA_Pos; - - // For now only the last opened endpoint can be closed without fuss. - TU_ASSERT(fifo_start == _dwc2_controller[rhport].ep_fifo_size / 4 - _allocated_fifo_words_tx,); - _allocated_fifo_words_tx -= fifo_size; - } else { - _out_ep_closed = true; // Set flag such that RX FIFO gets reduced in size once RX FIFO is empty - } } void dcd_edpt_stall(uint8_t rhport, uint8_t ep_addr) { @@ -1181,14 +1146,6 @@ void dcd_int_handler(uint8_t rhport) { handle_rxflvl_irq(rhport); } while (dwc2->gotgint & GINTSTS_RXFLVL); - // Manage RX FIFO size - if (_out_ep_closed) { - update_grxfsiz(rhport); - - // Disable flag - _out_ep_closed = false; - } - dwc2->gintmsk |= GINTMSK_RXFLVLM; } -- cgit v1.3.1 From cbbfbbb57ea8b4ea97ce4f2e2d157da9c25019fe Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 8 Apr 2024 13:16:08 +0700 Subject: add cpuctl and pinctl to tuh_configure() option for max3421 --- .github/workflows/build_iar.yml | 1 + src/host/usbh.h | 10 +++++++--- src/portable/analog/max3421/hcd_max3421.c | 18 +++++++++++------- 3 files changed, 19 insertions(+), 10 deletions(-) (limited to 'src/portable') diff --git a/.github/workflows/build_iar.yml b/.github/workflows/build_iar.yml index a0a022ecc..499349904 100644 --- a/.github/workflows/build_iar.yml +++ b/.github/workflows/build_iar.yml @@ -28,6 +28,7 @@ concurrency: jobs: cmake: + if: github.repository_owner == 'hathach' runs-on: [self-hosted, Linux, X64, hifiphile] strategy: fail-fast: false diff --git a/src/host/usbh.h b/src/host/usbh.h index 57362c778..359684169 100644 --- a/src/host/usbh.h +++ b/src/host/usbh.h @@ -80,12 +80,16 @@ enum { TUH_CFGID_MAX3421 = 200, }; +typedef struct { + uint8_t max_nak; // max NAK per endpoint per frame + uint8_t cpuctl; // R16: CPU Control Register + uint8_t pinctl; // R17: Pin Control Register. FDUPSPI bit is ignored +} tuh_configure_max3421_t; + typedef union { // For TUH_CFGID_RPI_PIO_USB_CONFIGURATION use pio_usb_configuration_t - struct { - uint8_t max_nak; - } max3421; + tuh_configure_max3421_t max3421; } tuh_configure_param_t; //--------------------------------------------------------------------+ diff --git a/src/portable/analog/max3421/hcd_max3421.c b/src/portable/analog/max3421/hcd_max3421.c index 059f674cd..39afb7505 100644 --- a/src/portable/analog/max3421/hcd_max3421.c +++ b/src/portable/analog/max3421/hcd_max3421.c @@ -233,7 +233,11 @@ typedef struct { static max3421_data_t _hcd_data; // max NAK before giving up in a frame. 0 means infinite NAKs -static uint8_t _max_nak = MAX_NAK_DEFAULT; +static tuh_configure_max3421_t _tuh_cfg = { + .max_nak = MAX_NAK_DEFAULT, + .cpuctl = 0, // default: INT pulse width = 10.6 us + .pinctl = 0, // default: negative edge interrupt +}; //--------------------------------------------------------------------+ // API: SPI transfer with MAX3421E @@ -416,7 +420,7 @@ static void free_ep(uint8_t daddr) { TU_ATTR_ALWAYS_INLINE static inline bool is_ep_pending(max3421_ep_t const * ep) { uint8_t const state = ep->state; return ep->packet_size && (state >= EP_STATE_ATTEMPT_1) && - (_max_nak == 0 || state < EP_STATE_ATTEMPT_1 + _max_nak); + (_tuh_cfg.max_nak == 0 || state < EP_STATE_ATTEMPT_1 + _tuh_cfg.max_nak); } // Find the next pending endpoint using round-robin scheduling, starting from next endpoint. @@ -454,7 +458,7 @@ bool hcd_configure(uint8_t rhport, uint32_t cfg_id, const void* cfg_param) { TU_VERIFY(cfg_id == TUH_CFGID_MAX3421 && cfg_param != NULL); tuh_configure_param_t const* cfg = (tuh_configure_param_t const*) cfg_param; - _max_nak = tu_min8(cfg->max3421.max_nak, EP_STATE_ATTEMPT_MAX-EP_STATE_ATTEMPT_1); + _tuh_cfg = cfg->max3421; return true; } @@ -476,7 +480,7 @@ bool hcd_init(uint8_t rhport) { #endif // full duplex, interrupt negative edge - reg_write(rhport, PINCTL_ADDR, PINCTL_FDUPSPI, false); + reg_write(rhport, PINCTL_ADDR, _tuh_cfg.pinctl | PINCTL_FDUPSPI, false); // v1 is 0x01, v2 is 0x12, v3 is 0x13 uint8_t const revision = reg_read(rhport, REVISION_ADDR, false); @@ -505,7 +509,7 @@ bool hcd_init(uint8_t rhport) { tuh_max3421_int_api(rhport, true); // Enable Interrupt pin - reg_write(rhport, CPUCTL_ADDR, CPUCTL_IE, false); + reg_write(rhport, CPUCTL_ADDR, _tuh_cfg.cpuctl | CPUCTL_IE, false); return true; } @@ -516,9 +520,9 @@ bool hcd_deinit(uint8_t rhport) { // disable interrupt tuh_max3421_int_api(rhport, false); - // reset max3421 + // reset max3421 and power down reg_write(rhport, USBCTL_ADDR, USBCTL_CHIPRES, false); - reg_write(rhport, USBCTL_ADDR, 0, false); + reg_write(rhport, USBCTL_ADDR, USBCTL_PWRDOWN, false); #if OSAL_MUTEX_REQUIRED osal_mutex_delete(_hcd_data.spi_mutex); -- cgit v1.3.1 From 47c12a07f2edf927eaa685ee8c32b222271d770f Mon Sep 17 00:00:00 2001 From: "Felix \"xq\" Queißner" Date: Mon, 2 Jan 2023 17:09:45 +0100 Subject: Implements tuh_deinit() and tud_deinit() to uninitialize host/device mode. --- src/device/dcd.h | 3 +++ src/device/usbd.h | 5 ++++- src/portable/raspberrypi/rp2040/dcd_rp2040.c | 12 ++++++++++++ src/portable/raspberrypi/rp2040/hcd_rp2040.c | 8 ++++++++ 4 files changed, 27 insertions(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/device/dcd.h b/src/device/dcd.h index 69c26bcf4..21f404e4f 100644 --- a/src/device/dcd.h +++ b/src/device/dcd.h @@ -122,6 +122,9 @@ void dcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) TU_ATTR_W // Initialize controller to device mode void dcd_init(uint8_t rhport); +// Deinitialize controller, unset device mode. +void dcd_deinit(uint8_t rhport); + // Interrupt Handler void dcd_int_handler(uint8_t rhport); diff --git a/src/device/usbd.h b/src/device/usbd.h index 2e3987b99..a9350192b 100644 --- a/src/device/usbd.h +++ b/src/device/usbd.h @@ -37,9 +37,12 @@ extern "C" { // Application API //--------------------------------------------------------------------+ -// Init device stack +// Init device stack on roothub port bool tud_init (uint8_t rhport); +// Deinit device stack on roothub port +void tud_deinit(uint8_t rhport); + // Check if device stack is already initialized bool tud_inited(void); diff --git a/src/portable/raspberrypi/rp2040/dcd_rp2040.c b/src/portable/raspberrypi/rp2040/dcd_rp2040.c index 5c564cb1c..ccc7ee102 100644 --- a/src/portable/raspberrypi/rp2040/dcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/dcd_rp2040.c @@ -407,6 +407,18 @@ void dcd_init(uint8_t rhport) { dcd_connect(rhport); } +void dcd_deinit(uint8_t rhport) { + assert(rhport == 0); + + dcd_disconnect(rhport); + reset_non_control_endpoints(); + irq_remove_handler(USBCTRL_IRQ, dcd_rp2040_irq); + + // reset usb hardware into initial state + reset_block(RESETS_RESET_USBCTRL_BITS); + unreset_block_wait(RESETS_RESET_USBCTRL_BITS); +} + void dcd_int_enable(__unused uint8_t rhport) { assert(rhport == 0); irq_set_enabled(USBCTRL_IRQ, true); diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index b351a9a07..762753a25 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -409,6 +409,14 @@ bool hcd_init(uint8_t rhport) return true; } +void hcd_deinit(uint8_t rhport) { + (void) rhport; + + irq_remove_handler(USBCTRL_IRQ, hcd_rp2040_irq); + reset_block(RESETS_RESET_USBCTRL_BITS); + unreset_block_wait(RESETS_RESET_USBCTRL_BITS); +} + void hcd_port_reset(uint8_t rhport) { (void) rhport; -- cgit v1.3.1 From c3c06484560d0102366a3a1b1101c35301009f97 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 8 Apr 2024 22:07:56 +0700 Subject: add class driver deinit --- src/class/audio/audio_device.c | 4 + src/class/audio/audio_device.h | 1 + src/class/bth/bth_device.c | 7 +- src/class/bth/bth_device.h | 1 + src/class/cdc/cdc_device.c | 32 ++++- src/class/cdc/cdc_device.h | 1 + src/class/dfu/dfu_device.c | 7 +- src/class/dfu/dfu_device.h | 1 + src/class/dfu/dfu_rt_device.c | 7 +- src/class/dfu/dfu_rt_device.h | 1 + src/class/hid/hid_device.c | 7 +- src/class/hid/hid_device.h | 1 + src/class/midi/midi_device.c | 36 ++++- src/class/midi/midi_device.h | 1 + src/class/msc/msc_device.c | 8 +- src/class/msc/msc_device.h | 1 + src/class/net/ecm_rndis_device.c | 7 +- src/class/net/ncm_device.c | 4 + src/class/net/net_device.h | 1 + src/class/usbtmc/usbtmc_device.c | 5 + src/class/usbtmc/usbtmc_device.h | 3 +- src/class/vendor/vendor_device.c | 38 ++++- src/class/vendor/vendor_device.h | 1 + src/class/video/video_device.c | 4 + src/class/video/video_device.h | 1 + src/device/dcd.h | 2 +- src/device/usbd.c | 204 +++++++++++++++++---------- src/device/usbd.h | 2 +- src/device/usbd_pvt.h | 4 +- src/host/usbh.c | 2 +- src/portable/raspberrypi/rp2040/dcd_rp2040.c | 5 +- src/portable/raspberrypi/rp2040/hcd_rp2040.c | 4 +- src/tusb_option.h | 2 +- 33 files changed, 292 insertions(+), 113 deletions(-) (limited to 'src/portable') diff --git a/src/class/audio/audio_device.c b/src/class/audio/audio_device.c index 9a361419b..7077d66f8 100644 --- a/src/class/audio/audio_device.c +++ b/src/class/audio/audio_device.c @@ -1396,6 +1396,10 @@ void audiod_init(void) } } +bool audiod_deinit(void) { + return false; // TODO not implemented yet +} + void audiod_reset(uint8_t rhport) { (void) rhport; diff --git a/src/class/audio/audio_device.h b/src/class/audio/audio_device.h index 040a760d6..b16514fd4 100644 --- a/src/class/audio/audio_device.h +++ b/src/class/audio/audio_device.h @@ -685,6 +685,7 @@ static inline bool tud_audio_fb_set(uint32_t feedback) // Internal Class Driver API //--------------------------------------------------------------------+ void audiod_init (void); +bool audiod_deinit (void); void audiod_reset (uint8_t rhport); uint16_t audiod_open (uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool audiod_control_xfer_cb(uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); diff --git a/src/class/bth/bth_device.c b/src/class/bth/bth_device.c index f145e2ead..cbf6e1332 100755 --- a/src/class/bth/bth_device.c +++ b/src/class/bth/bth_device.c @@ -91,11 +91,14 @@ bool tud_bt_acl_data_send(void *event, uint16_t event_len) //--------------------------------------------------------------------+ // USBD Driver API //--------------------------------------------------------------------+ -void btd_init(void) -{ +void btd_init(void) { tu_memclr(&_btd_itf, sizeof(_btd_itf)); } +bool btd_deinit(void) { + return true; +} + void btd_reset(uint8_t rhport) { (void)rhport; diff --git a/src/class/bth/bth_device.h b/src/class/bth/bth_device.h index e782c532b..4f6350839 100755 --- a/src/class/bth/bth_device.h +++ b/src/class/bth/bth_device.h @@ -104,6 +104,7 @@ bool tud_bt_acl_data_send(void *acl_data, uint16_t data_len); // Internal Class Driver API //--------------------------------------------------------------------+ void btd_init (void); +bool btd_deinit (void); void btd_reset (uint8_t rhport); uint16_t btd_open (uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool btd_control_xfer_cb (uint8_t rhport, uint8_t stage, tusb_control_request_t const *request); diff --git a/src/class/cdc/cdc_device.c b/src/class/cdc/cdc_device.c index c26264e60..7ef0530ec 100644 --- a/src/class/cdc/cdc_device.c +++ b/src/class/cdc/cdc_device.c @@ -253,11 +253,39 @@ void cdcd_init(void) // In this way, the most current data is prioritized. tu_fifo_config(&p_cdc->tx_ff, p_cdc->tx_ff_buf, TU_ARRAY_SIZE(p_cdc->tx_ff_buf), 1, true); - tu_fifo_config_mutex(&p_cdc->rx_ff, NULL, osal_mutex_create(&p_cdc->rx_ff_mutex)); - tu_fifo_config_mutex(&p_cdc->tx_ff, osal_mutex_create(&p_cdc->tx_ff_mutex), NULL); + #if OSAL_MUTEX_REQUIRED + osal_mutex_t mutex_rd = osal_mutex_create(&p_cdc->rx_ff_mutex); + osal_mutex_t mutex_wr = osal_mutex_create(&p_cdc->tx_ff_mutex); + TU_ASSERT(mutex_rd != NULL && mutex_wr != NULL, ); + + tu_fifo_config_mutex(&p_cdc->rx_ff, NULL, mutex_rd); + tu_fifo_config_mutex(&p_cdc->tx_ff, mutex_wr, NULL); + #endif } } +bool cdcd_deinit(void) { + #if OSAL_MUTEX_REQUIRED + for(uint8_t i=0; irx_ff.mutex_rd; + osal_mutex_t mutex_wr = p_cdc->tx_ff.mutex_wr; + + if (mutex_rd) { + osal_mutex_delete(mutex_rd); + tu_fifo_config_mutex(&p_cdc->rx_ff, NULL, NULL); + } + + if (mutex_wr) { + osal_mutex_delete(mutex_wr); + tu_fifo_config_mutex(&p_cdc->tx_ff, NULL, NULL); + } + } + #endif + + return true; +} + void cdcd_reset(uint8_t rhport) { (void) rhport; diff --git a/src/class/cdc/cdc_device.h b/src/class/cdc/cdc_device.h index a6e07aa5c..20e908451 100644 --- a/src/class/cdc/cdc_device.h +++ b/src/class/cdc/cdc_device.h @@ -247,6 +247,7 @@ static inline bool tud_cdc_write_clear(void) // INTERNAL USBD-CLASS DRIVER API //--------------------------------------------------------------------+ void cdcd_init (void); +bool cdcd_deinit (void); void cdcd_reset (uint8_t rhport); uint16_t cdcd_open (uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool cdcd_control_xfer_cb (uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); diff --git a/src/class/dfu/dfu_device.c b/src/class/dfu/dfu_device.c index 3e7c13dea..71e7ac2b3 100644 --- a/src/class/dfu/dfu_device.c +++ b/src/class/dfu/dfu_device.c @@ -160,11 +160,14 @@ void dfu_moded_reset(uint8_t rhport) reset_state(); } -void dfu_moded_init(void) -{ +void dfu_moded_init(void) { dfu_moded_reset(0); } +bool dfu_moded_deinit(void) { + return true; +} + uint16_t dfu_moded_open(uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len) { (void) rhport; diff --git a/src/class/dfu/dfu_device.h b/src/class/dfu/dfu_device.h index fecf8596f..00c22ea8b 100644 --- a/src/class/dfu/dfu_device.h +++ b/src/class/dfu/dfu_device.h @@ -86,6 +86,7 @@ TU_ATTR_WEAK void tud_dfu_abort_cb(uint8_t alt); // Internal Class Driver API //--------------------------------------------------------------------+ void dfu_moded_init(void); +bool dfu_moded_deinit(void); void dfu_moded_reset(uint8_t rhport); uint16_t dfu_moded_open(uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool dfu_moded_control_xfer_cb(uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); diff --git a/src/class/dfu/dfu_rt_device.c b/src/class/dfu/dfu_rt_device.c index a940d8d62..3b801b787 100644 --- a/src/class/dfu/dfu_rt_device.c +++ b/src/class/dfu/dfu_rt_device.c @@ -51,8 +51,11 @@ //--------------------------------------------------------------------+ // USBD Driver API //--------------------------------------------------------------------+ -void dfu_rtd_init(void) -{ +void dfu_rtd_init(void) { +} + +bool dfu_rtd_deinit(void) { + return true; } void dfu_rtd_reset(uint8_t rhport) diff --git a/src/class/dfu/dfu_rt_device.h b/src/class/dfu/dfu_rt_device.h index babaa8214..67eb26d95 100644 --- a/src/class/dfu/dfu_rt_device.h +++ b/src/class/dfu/dfu_rt_device.h @@ -43,6 +43,7 @@ void tud_dfu_runtime_reboot_to_dfu_cb(void); // Internal Class Driver API //--------------------------------------------------------------------+ void dfu_rtd_init(void); +bool dfu_rtd_deinit(void); void dfu_rtd_reset(uint8_t rhport); uint16_t dfu_rtd_open(uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool dfu_rtd_control_xfer_cb(uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); diff --git a/src/class/hid/hid_device.c b/src/class/hid/hid_device.c index 5637ea6b4..e8eda1400 100644 --- a/src/class/hid/hid_device.c +++ b/src/class/hid/hid_device.c @@ -166,11 +166,14 @@ bool tud_hid_n_gamepad_report(uint8_t instance, uint8_t report_id, //--------------------------------------------------------------------+ // USBD-CLASS API //--------------------------------------------------------------------+ -void hidd_init(void) -{ +void hidd_init(void) { hidd_reset(0); } +bool hidd_deinit(void) { + return true; +} + void hidd_reset(uint8_t rhport) { (void) rhport; diff --git a/src/class/hid/hid_device.h b/src/class/hid/hid_device.h index 17b24def1..53ecf9c06 100644 --- a/src/class/hid/hid_device.h +++ b/src/class/hid/hid_device.h @@ -406,6 +406,7 @@ static inline bool tud_hid_gamepad_report(uint8_t report_id, int8_t x, int8_t y // Internal Class Driver API //--------------------------------------------------------------------+ void hidd_init (void); +bool hidd_deinit (void); void hidd_reset (uint8_t rhport); uint16_t hidd_open (uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool hidd_control_xfer_cb (uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); diff --git a/src/class/midi/midi_device.c b/src/class/midi/midi_device.c index 052372a93..42905ab0d 100644 --- a/src/class/midi/midi_device.c +++ b/src/class/midi/midi_device.c @@ -373,12 +373,10 @@ bool tud_midi_n_packet_write (uint8_t itf, uint8_t const packet[4]) //--------------------------------------------------------------------+ // USBD Driver API //--------------------------------------------------------------------+ -void midid_init(void) -{ +void midid_init(void) { tu_memclr(_midid_itf, sizeof(_midid_itf)); - for(uint8_t i=0; itx_ff, midi->tx_ff_buf, CFG_TUD_MIDI_TX_BUFSIZE, 1, false); // OBVS. #if CFG_FIFO_MUTEX - tu_fifo_config_mutex(&midi->rx_ff, NULL, osal_mutex_create(&midi->rx_ff_mutex)); - tu_fifo_config_mutex(&midi->tx_ff, osal_mutex_create(&midi->tx_ff_mutex), NULL); + osal_mutex_t mutex_rd = osal_mutex_create(&midi->rx_ff_mutex); + osal_mutex_t mutex_wr = osal_mutex_create(&midi->tx_ff_mutex); + TU_ASSERT(mutex_wr != NULL && mutex_wr != NULL, ); + + tu_fifo_config_mutex(&midi->rx_ff, NULL, mutex_rd); + tu_fifo_config_mutex(&midi->tx_ff, mutex_wr, NULL); #endif } } +bool midid_deinit(void) { + #if CFG_FIFO_MUTEX + for(uint8_t i=0; irx_ff.mutex_rd; + osal_mutex_t mutex_wr = midi->tx_ff.mutex_wr; + + if (mutex_rd) { + osal_mutex_delete(mutex_rd); + tu_fifo_config_mutex(&midi->rx_ff, NULL, NULL); + } + + if (mutex_wr) { + osal_mutex_delete(mutex_wr); + tu_fifo_config_mutex(&midi->tx_ff, NULL, NULL); + } + } + #endif + + return true; +} + void midid_reset(uint8_t rhport) { (void) rhport; diff --git a/src/class/midi/midi_device.h b/src/class/midi/midi_device.h index 1c6f996be..3e89cc0a3 100644 --- a/src/class/midi/midi_device.h +++ b/src/class/midi/midi_device.h @@ -158,6 +158,7 @@ static inline bool tud_midi_packet_write (uint8_t const packet[4]) // Internal Class Driver API //--------------------------------------------------------------------+ void midid_init (void); +bool midid_deinit (void); void midid_reset (uint8_t rhport); uint16_t midid_open (uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool midid_control_xfer_cb (uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); diff --git a/src/class/msc/msc_device.c b/src/class/msc/msc_device.c index c145d86a6..588fcaaca 100644 --- a/src/class/msc/msc_device.c +++ b/src/class/msc/msc_device.c @@ -251,11 +251,15 @@ static inline void set_sense_medium_not_present(uint8_t lun) //--------------------------------------------------------------------+ // USBD Driver API //--------------------------------------------------------------------+ -void mscd_init(void) -{ +void mscd_init(void) { tu_memclr(&_mscd_itf, sizeof(mscd_interface_t)); } +bool mscd_deinit(void) { + // nothing to do + return true; +} + void mscd_reset(uint8_t rhport) { (void) rhport; diff --git a/src/class/msc/msc_device.h b/src/class/msc/msc_device.h index 72f95be06..4247a40bd 100644 --- a/src/class/msc/msc_device.h +++ b/src/class/msc/msc_device.h @@ -150,6 +150,7 @@ TU_ATTR_WEAK bool tud_msc_is_writable_cb(uint8_t lun); // Internal Class Driver API //--------------------------------------------------------------------+ void mscd_init (void); +bool mscd_deinit (void); void mscd_reset (uint8_t rhport); uint16_t mscd_open (uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool mscd_control_xfer_cb (uint8_t rhport, uint8_t stage, tusb_control_request_t const * p_request); diff --git a/src/class/net/ecm_rndis_device.c b/src/class/net/ecm_rndis_device.c index 762425732..f7a5fd225 100644 --- a/src/class/net/ecm_rndis_device.c +++ b/src/class/net/ecm_rndis_device.c @@ -132,11 +132,14 @@ void netd_report(uint8_t *buf, uint16_t len) //--------------------------------------------------------------------+ // USBD Driver API //--------------------------------------------------------------------+ -void netd_init(void) -{ +void netd_init(void) { tu_memclr(&_netd_itf, sizeof(_netd_itf)); } +bool netd_deinit(void) { + return true; +} + void netd_reset(uint8_t rhport) { (void) rhport; diff --git a/src/class/net/ncm_device.c b/src/class/net/ncm_device.c index 226c42c4e..f84bd9f73 100644 --- a/src/class/net/ncm_device.c +++ b/src/class/net/ncm_device.c @@ -260,6 +260,10 @@ void netd_init(void) ncm_prepare_for_tx(); } +bool netd_deinit(void) { + return true; +} + void netd_reset(uint8_t rhport) { (void) rhport; diff --git a/src/class/net/net_device.h b/src/class/net/net_device.h index 399916355..da1a7b1e8 100644 --- a/src/class/net/net_device.h +++ b/src/class/net/net_device.h @@ -105,6 +105,7 @@ void tud_network_link_state_cb(bool state); // INTERNAL USBD-CLASS DRIVER API //--------------------------------------------------------------------+ void netd_init (void); +bool netd_deinit (void); void netd_reset (uint8_t rhport); uint16_t netd_open (uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool netd_control_xfer_cb (uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); diff --git a/src/class/usbtmc/usbtmc_device.c b/src/class/usbtmc/usbtmc_device.c index 573654d58..972a450e6 100644 --- a/src/class/usbtmc/usbtmc_device.c +++ b/src/class/usbtmc/usbtmc_device.c @@ -260,6 +260,11 @@ void usbtmcd_init_cb(void) usbtmcLock = osal_mutex_create(&usbtmcLockBuffer); } +bool usbtmcd_deinit(void) { + osal_mutex_delete(usbtmcLock); + return true; +} + uint16_t usbtmcd_open_cb(uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len) { (void)rhport; diff --git a/src/class/usbtmc/usbtmc_device.h b/src/class/usbtmc/usbtmc_device.h index c1298ddb8..3299a36eb 100644 --- a/src/class/usbtmc/usbtmc_device.h +++ b/src/class/usbtmc/usbtmc_device.h @@ -98,11 +98,12 @@ bool tud_usbtmc_start_bus_read(void); /* "callbacks" from USB device core */ +void usbtmcd_init_cb(void); +bool usbtmcd_deinit(void); uint16_t usbtmcd_open_cb(uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); void usbtmcd_reset_cb(uint8_t rhport); bool usbtmcd_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t result, uint32_t xferred_bytes); bool usbtmcd_control_xfer_cb(uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); -void usbtmcd_init_cb(void); /************************************************************ * USBTMC Descriptor Templates diff --git a/src/class/vendor/vendor_device.c b/src/class/vendor/vendor_device.c index a68cb2156..e87ce3997 100644 --- a/src/class/vendor/vendor_device.c +++ b/src/class/vendor/vendor_device.c @@ -169,21 +169,47 @@ uint32_t tud_vendor_n_write_available (uint8_t itf) //--------------------------------------------------------------------+ // USBD Driver API //--------------------------------------------------------------------+ -void vendord_init(void) -{ +void vendord_init(void) { tu_memclr(_vendord_itf, sizeof(_vendord_itf)); - for(uint8_t i=0; irx_ff, p_itf->rx_ff_buf, CFG_TUD_VENDOR_RX_BUFSIZE, 1, false); tu_fifo_config(&p_itf->tx_ff, p_itf->tx_ff_buf, CFG_TUD_VENDOR_TX_BUFSIZE, 1, false); - tu_fifo_config_mutex(&p_itf->rx_ff, NULL, osal_mutex_create(&p_itf->rx_ff_mutex)); - tu_fifo_config_mutex(&p_itf->tx_ff, osal_mutex_create(&p_itf->tx_ff_mutex), NULL); + #if OSAL_MUTEX_REQUIRED + osal_mutex_t mutex_rd = osal_mutex_create(&p_itf->rx_ff_mutex); + osal_mutex_t mutex_wr = osal_mutex_create(&p_itf->tx_ff_mutex); + TU_ASSERT(mutex_rd && mutex_wr,); + + tu_fifo_config_mutex(&p_itf->rx_ff, NULL, mutex_rd); + tu_fifo_config_mutex(&p_itf->tx_ff, mutex_wr, NULL); + #endif + } +} + +bool vendord_deinit(void) { + #if OSAL_MUTEX_REQUIRED + for(uint8_t i=0; irx_ff.mutex_rd; + osal_mutex_t mutex_wr = p_itf->tx_ff.mutex_wr; + + if (mutex_rd) { + osal_mutex_delete(mutex_rd); + tu_fifo_config_mutex(&p_itf->rx_ff, NULL, NULL); + } + + if (mutex_wr) { + osal_mutex_delete(mutex_wr); + tu_fifo_config_mutex(&p_itf->tx_ff, NULL, NULL); + } } + #endif + + return true; } void vendord_reset(uint8_t rhport) diff --git a/src/class/vendor/vendor_device.h b/src/class/vendor/vendor_device.h index d239406b4..cd69ec7c6 100644 --- a/src/class/vendor/vendor_device.h +++ b/src/class/vendor/vendor_device.h @@ -139,6 +139,7 @@ static inline uint32_t tud_vendor_write_available (void) // Internal Class Driver API //--------------------------------------------------------------------+ void vendord_init(void); +bool vendord_deinit(void); void vendord_reset(uint8_t rhport); uint16_t vendord_open(uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool vendord_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t event, uint32_t xferred_bytes); diff --git a/src/class/video/video_device.c b/src/class/video/video_device.c index 5306356ba..c30690232 100644 --- a/src/class/video/video_device.c +++ b/src/class/video/video_device.c @@ -1229,6 +1229,10 @@ void videod_init(void) { } } +bool videod_deinit(void) { + return true; +} + void videod_reset(uint8_t rhport) { (void) rhport; for (uint_fast8_t i = 0; i < CFG_TUD_VIDEO; ++i) { diff --git a/src/class/video/video_device.h b/src/class/video/video_device.h index ee2fcb9d5..92930c013 100644 --- a/src/class/video/video_device.h +++ b/src/class/video/video_device.h @@ -85,6 +85,7 @@ TU_ATTR_WEAK int tud_video_commit_cb(uint_fast8_t ctl_idx, uint_fast8_t stm_idx, // INTERNAL USBD-CLASS DRIVER API //--------------------------------------------------------------------+ void videod_init (void); +bool videod_deinit (void); void videod_reset (uint8_t rhport); uint16_t videod_open (uint8_t rhport, tusb_desc_interface_t const * itf_desc, uint16_t max_len); bool videod_control_xfer_cb(uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); diff --git a/src/device/dcd.h b/src/device/dcd.h index 21f404e4f..d4f105aa3 100644 --- a/src/device/dcd.h +++ b/src/device/dcd.h @@ -123,7 +123,7 @@ void dcd_dcache_clean_invalidate(void const* addr, uint32_t data_size) TU_ATTR_W void dcd_init(uint8_t rhport); // Deinitialize controller, unset device mode. -void dcd_deinit(uint8_t rhport); +bool dcd_deinit(uint8_t rhport); // Interrupt Handler void dcd_int_handler(uint8_t rhport); diff --git a/src/device/usbd.c b/src/device/usbd.c index 8f98862c6..439e071ff 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -43,8 +43,13 @@ #endif //--------------------------------------------------------------------+ -// Callback weak stubs (called if application does not provide) +// Weak stubs: invoked if no strong implementation is available //--------------------------------------------------------------------+ +TU_ATTR_WEAK bool dcd_deinit(uint8_t rhport) { + (void) rhport; + return false; +} + TU_ATTR_WEAK void tud_event_hook_cb(uint8_t rhport, uint32_t eventid, bool in_isr) { (void)rhport; (void)eventid; @@ -85,17 +90,18 @@ tu_static usbd_device_t _usbd_dev; // Class Driver //--------------------------------------------------------------------+ #if CFG_TUSB_DEBUG >= CFG_TUD_LOG_LEVEL - #define DRIVER_NAME(_name) .name = _name, + #define DRIVER_NAME(_name) _name #else - #define DRIVER_NAME(_name) + #define DRIVER_NAME(_name) NULL #endif // Built-in class drivers tu_static usbd_class_driver_t const _usbd_driver[] = { #if CFG_TUD_CDC { - DRIVER_NAME("CDC") + .name = DRIVER_NAME("CDC"), .init = cdcd_init, + .deinit = cdcd_deinit, .reset = cdcd_reset, .open = cdcd_open, .control_xfer_cb = cdcd_control_xfer_cb, @@ -106,8 +112,9 @@ tu_static usbd_class_driver_t const _usbd_driver[] = { #if CFG_TUD_MSC { - DRIVER_NAME("MSC") + .name = DRIVER_NAME("MSC"), .init = mscd_init, + .deinit = NULL, .reset = mscd_reset, .open = mscd_open, .control_xfer_cb = mscd_control_xfer_cb, @@ -118,121 +125,131 @@ tu_static usbd_class_driver_t const _usbd_driver[] = { #if CFG_TUD_HID { - DRIVER_NAME("HID") - .init = hidd_init, - .reset = hidd_reset, - .open = hidd_open, - .control_xfer_cb = hidd_control_xfer_cb, - .xfer_cb = hidd_xfer_cb, - .sof = NULL + .name = DRIVER_NAME("HID"), + .init = hidd_init, + .deinit = hidd_deinit, + .reset = hidd_reset, + .open = hidd_open, + .control_xfer_cb = hidd_control_xfer_cb, + .xfer_cb = hidd_xfer_cb, + .sof = NULL }, #endif #if CFG_TUD_AUDIO { - DRIVER_NAME("AUDIO") - .init = audiod_init, - .reset = audiod_reset, - .open = audiod_open, - .control_xfer_cb = audiod_control_xfer_cb, - .xfer_cb = audiod_xfer_cb, - .sof = audiod_sof_isr + .name = DRIVER_NAME("AUDIO"), + .init = audiod_init, + .deinit = audiod_deinit, + .reset = audiod_reset, + .open = audiod_open, + .control_xfer_cb = audiod_control_xfer_cb, + .xfer_cb = audiod_xfer_cb, + .sof = audiod_sof_isr }, #endif #if CFG_TUD_VIDEO { - DRIVER_NAME("VIDEO") - .init = videod_init, - .reset = videod_reset, - .open = videod_open, - .control_xfer_cb = videod_control_xfer_cb, - .xfer_cb = videod_xfer_cb, - .sof = NULL + .name = DRIVER_NAME("VIDEO"), + .init = videod_init, + .deinit = videod_deinit, + .reset = videod_reset, + .open = videod_open, + .control_xfer_cb = videod_control_xfer_cb, + .xfer_cb = videod_xfer_cb, + .sof = NULL }, #endif #if CFG_TUD_MIDI { - DRIVER_NAME("MIDI") - .init = midid_init, - .open = midid_open, - .reset = midid_reset, - .control_xfer_cb = midid_control_xfer_cb, - .xfer_cb = midid_xfer_cb, - .sof = NULL + .name = DRIVER_NAME("MIDI"), + .init = midid_init, + .deinit = midid_deinit, + .open = midid_open, + .reset = midid_reset, + .control_xfer_cb = midid_control_xfer_cb, + .xfer_cb = midid_xfer_cb, + .sof = NULL }, #endif #if CFG_TUD_VENDOR { - DRIVER_NAME("VENDOR") - .init = vendord_init, - .reset = vendord_reset, - .open = vendord_open, - .control_xfer_cb = tud_vendor_control_xfer_cb, - .xfer_cb = vendord_xfer_cb, - .sof = NULL + .name = DRIVER_NAME("VENDOR"), + .init = vendord_init, + .deinit = vendord_deinit, + .reset = vendord_reset, + .open = vendord_open, + .control_xfer_cb = tud_vendor_control_xfer_cb, + .xfer_cb = vendord_xfer_cb, + .sof = NULL }, #endif #if CFG_TUD_USBTMC { - DRIVER_NAME("TMC") - .init = usbtmcd_init_cb, - .reset = usbtmcd_reset_cb, - .open = usbtmcd_open_cb, - .control_xfer_cb = usbtmcd_control_xfer_cb, - .xfer_cb = usbtmcd_xfer_cb, - .sof = NULL + .name = DRIVER_NAME("TMC"), + .init = usbtmcd_init_cb, + .deinit = usbtmcd_deinit, + .reset = usbtmcd_reset_cb, + .open = usbtmcd_open_cb, + .control_xfer_cb = usbtmcd_control_xfer_cb, + .xfer_cb = usbtmcd_xfer_cb, + .sof = NULL }, #endif #if CFG_TUD_DFU_RUNTIME { - DRIVER_NAME("DFU-RUNTIME") - .init = dfu_rtd_init, - .reset = dfu_rtd_reset, - .open = dfu_rtd_open, - .control_xfer_cb = dfu_rtd_control_xfer_cb, - .xfer_cb = NULL, - .sof = NULL + .name = DRIVER_NAME("DFU-RUNTIME"), + .init = dfu_rtd_init, + .deinit = dfu_rtd_deinit, + .reset = dfu_rtd_reset, + .open = dfu_rtd_open, + .control_xfer_cb = dfu_rtd_control_xfer_cb, + .xfer_cb = NULL, + .sof = NULL }, #endif #if CFG_TUD_DFU { - DRIVER_NAME("DFU") - .init = dfu_moded_init, - .reset = dfu_moded_reset, - .open = dfu_moded_open, - .control_xfer_cb = dfu_moded_control_xfer_cb, - .xfer_cb = NULL, - .sof = NULL + .name = DRIVER_NAME("DFU"), + .init = dfu_moded_init, + .deinit = dfu_moded_deinit, + .reset = dfu_moded_reset, + .open = dfu_moded_open, + .control_xfer_cb = dfu_moded_control_xfer_cb, + .xfer_cb = NULL, + .sof = NULL }, #endif #if CFG_TUD_ECM_RNDIS || CFG_TUD_NCM { - DRIVER_NAME("NET") - .init = netd_init, - .reset = netd_reset, - .open = netd_open, - .control_xfer_cb = netd_control_xfer_cb, - .xfer_cb = netd_xfer_cb, - .sof = NULL, + .name = DRIVER_NAME("NET"), + .init = netd_init, + .deinit = netd_deinit, + .reset = netd_reset, + .open = netd_open, + .control_xfer_cb = netd_control_xfer_cb, + .xfer_cb = netd_xfer_cb, + .sof = NULL, }, #endif #if CFG_TUD_BTH { - DRIVER_NAME("BTH") - .init = btd_init, - .reset = btd_reset, - .open = btd_open, - .control_xfer_cb = btd_control_xfer_cb, - .xfer_cb = btd_xfer_cb, - .sof = NULL + .name = DRIVER_NAME("BTH"), + .init = btd_init, + .deinit = btd_deinit, + .reset = btd_reset, + .open = btd_open, + .control_xfer_cb = btd_control_xfer_cb, + .xfer_cb = btd_xfer_cb, + .sof = NULL }, #endif }; @@ -402,7 +419,7 @@ bool tud_init(uint8_t rhport) { // Init class drivers for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) { usbd_class_driver_t const* driver = get_driver(i); - TU_ASSERT(driver); + TU_ASSERT(driver && driver->init); TU_LOG_USBD("%s init\r\n", driver->name); driver->init(); } @@ -416,6 +433,41 @@ bool tud_init(uint8_t rhport) { return true; } +bool tud_deinit(uint8_t rhport) { + // skip if not initialized + if (!tud_inited()) return true; + + TU_LOG_USBD("USBD deinit on controller %u\r\n", rhport); + + // Deinit device controller driver + dcd_int_disable(rhport); + dcd_disconnect(rhport); + dcd_deinit(rhport); + + // Deinit class drivers + for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) { + usbd_class_driver_t const* driver = get_driver(i); + if(driver && driver->deinit) { + TU_LOG_USBD("%s deinit\r\n", driver->name); + driver->deinit(); + } + } + + // Deinit device queue & task + osal_queue_delete(_usbd_q); + _usbd_q = NULL; + +#if OSAL_MUTEX_REQUIRED + // TODO make sure there is no task waiting on this mutex + osal_mutex_delete(_usbd_mutex); + _usbd_mutex = NULL; +#endif + + _usbd_rhport = RHPORT_INVALID; + + return true; +} + static void configuration_reset(uint8_t rhport) { for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) { usbd_class_driver_t const* driver = get_driver(i); diff --git a/src/device/usbd.h b/src/device/usbd.h index a9350192b..0197628e2 100644 --- a/src/device/usbd.h +++ b/src/device/usbd.h @@ -41,7 +41,7 @@ extern "C" { bool tud_init (uint8_t rhport); // Deinit device stack on roothub port -void tud_deinit(uint8_t rhport); +bool tud_deinit(uint8_t rhport); // Check if device stack is already initialized bool tud_inited(void); diff --git a/src/device/usbd_pvt.h b/src/device/usbd_pvt.h index 9039bc9d6..5ae96e589 100644 --- a/src/device/usbd_pvt.h +++ b/src/device/usbd_pvt.h @@ -40,11 +40,9 @@ //--------------------------------------------------------------------+ typedef struct { - #if CFG_TUSB_DEBUG >= CFG_TUD_LOG_LEVEL char const* name; - #endif - void (* init ) (void); + bool (* deinit ) (void); void (* reset ) (uint8_t rhport); uint16_t (* open ) (uint8_t rhport, tusb_desc_interface_t const * desc_intf, uint16_t max_len); bool (* control_xfer_cb ) (uint8_t rhport, uint8_t stage, tusb_control_request_t const * request); diff --git a/src/host/usbh.c b/src/host/usbh.c index aa0603d47..6a5491998 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -425,7 +425,7 @@ bool tuh_deinit(uint8_t rhport) { // Class drivers for (uint8_t drv_id = 0; drv_id < TOTAL_DRIVER_COUNT; drv_id++) { usbh_class_driver_t const* driver = get_driver(drv_id); - if (driver) { + if (driver && driver->deinit) { TU_LOG_USBH("%s deinit\r\n", driver->name); driver->deinit(); } diff --git a/src/portable/raspberrypi/rp2040/dcd_rp2040.c b/src/portable/raspberrypi/rp2040/dcd_rp2040.c index ccc7ee102..a2b3375a3 100644 --- a/src/portable/raspberrypi/rp2040/dcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/dcd_rp2040.c @@ -407,16 +407,17 @@ void dcd_init(uint8_t rhport) { dcd_connect(rhport); } -void dcd_deinit(uint8_t rhport) { +bool dcd_deinit(uint8_t rhport) { assert(rhport == 0); - dcd_disconnect(rhport); reset_non_control_endpoints(); irq_remove_handler(USBCTRL_IRQ, dcd_rp2040_irq); // reset usb hardware into initial state reset_block(RESETS_RESET_USBCTRL_BITS); unreset_block_wait(RESETS_RESET_USBCTRL_BITS); + + return true; } void dcd_int_enable(__unused uint8_t rhport) { diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 762753a25..222dbbbf0 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -409,12 +409,14 @@ bool hcd_init(uint8_t rhport) return true; } -void hcd_deinit(uint8_t rhport) { +bool hcd_deinit(uint8_t rhport) { (void) rhport; irq_remove_handler(USBCTRL_IRQ, hcd_rp2040_irq); reset_block(RESETS_RESET_USBCTRL_BITS); unreset_block_wait(RESETS_RESET_USBCTRL_BITS); + + return true; } void hcd_port_reset(uint8_t rhport) diff --git a/src/tusb_option.h b/src/tusb_option.h index 2921d3ae0..cbcb69edd 100644 --- a/src/tusb_option.h +++ b/src/tusb_option.h @@ -34,7 +34,7 @@ #define TUSB_VERSION_MAJOR 0 #define TUSB_VERSION_MINOR 16 #define TUSB_VERSION_REVISION 0 -#define TUSB_VERSION_BUILD 2 +#define TUSB_VERSION_BUILD 3 #define TUSB_VERSION_NUMBER (TUSB_VERSION_MAJOR << 24 | TUSB_VERSION_MINOR << 16 | TUSB_VERSION_REVISION << 8 | TUSB_VERSION_BUILD) #define TUSB_VERSION_STRING TU_STRING(TUSB_VERSION_MAJOR) "." TU_STRING(TUSB_VERSION_MINOR) "." TU_STRING(TUSB_VERSION_REVISION) -- cgit v1.3.1 From 4bc6a5feb74e073824cf404916442311b7040c47 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 8 Apr 2024 22:22:00 +0700 Subject: fix unused warning --- src/portable/raspberrypi/rp2040/dcd_rp2040.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'src/portable') diff --git a/src/portable/raspberrypi/rp2040/dcd_rp2040.c b/src/portable/raspberrypi/rp2040/dcd_rp2040.c index a2b3375a3..bc0deee32 100644 --- a/src/portable/raspberrypi/rp2040/dcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/dcd_rp2040.c @@ -408,7 +408,7 @@ void dcd_init(uint8_t rhport) { } bool dcd_deinit(uint8_t rhport) { - assert(rhport == 0); + (void) rhport; reset_non_control_endpoints(); irq_remove_handler(USBCTRL_IRQ, dcd_rp2040_irq); -- cgit v1.3.1