From 19d054f7892beda36c7f6fe5f07d84a13db7df16 Mon Sep 17 00:00:00 2001 From: Liam Fraser Date: Thu, 13 Jan 2022 11:17:08 +0000 Subject: hcd_rp2040 improvements: - Stall now has priority over other interrupt responses - Delete eunused hcd_edpt_busy - Assert !ep->active when trying to start a new xfer - Assert !ep->active when handling buff_status bits - Set ep->xferred_len to 8 once a setup packet is finished so the data structure is accurate --- src/portable/raspberrypi/rp2040/hcd_rp2040.c | 46 +++++++++++++--------------- 1 file changed, 22 insertions(+), 24 deletions(-) (limited to 'src') diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 063a8acd0..dddb9cd90 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -104,6 +104,8 @@ static void __no_inline_not_in_flash_func(hw_xfer_complete)(struct hw_endpoint * static void __no_inline_not_in_flash_func(_handle_buff_status_bit)(uint bit, struct hw_endpoint *ep) { usb_hw_clear->buf_status = bit; + // EP may have been stalled? + assert(ep->active); bool done = hw_endpoint_xfer_continue(ep); if (done) { @@ -166,6 +168,8 @@ static void __no_inline_not_in_flash_func(hw_trans_complete)(void) pico_trace("Sent setup packet\n"); struct hw_endpoint *ep = &epx; assert(ep->active); + // Set transferred length to 8 for a setup packet + ep->xferred_len = 8; hw_xfer_complete(ep, XFER_RESULT_SUCCESS); } else @@ -197,6 +201,18 @@ static void __no_inline_not_in_flash_func(hcd_rp2040_irq)(void) usb_hw_clear->sie_status = USB_SIE_STATUS_SPEED_BITS; } + if (status & USB_INTS_STALL_BITS) + { + // We have rx'd a stall from the device + // NOTE THIS SHOULD HAVE PRIORITY OVER BUFF_STATUS + // AND TRANS_COMPLETE as the stall is an alternative response + // to one of those events + pico_trace("Stall REC\n"); + handled |= USB_INTS_STALL_BITS; + usb_hw_clear->sie_status = USB_SIE_STATUS_STALL_REC_BITS; + hw_xfer_complete(&epx, XFER_RESULT_STALLED); + } + if (status & USB_INTS_BUFF_STATUS_BITS) { handled |= USB_INTS_BUFF_STATUS_BITS; @@ -212,15 +228,6 @@ static void __no_inline_not_in_flash_func(hcd_rp2040_irq)(void) hw_trans_complete(); } - if (status & USB_INTS_STALL_BITS) - { - // We have rx'd a stall from the device - pico_trace("Stall REC\n"); - handled |= USB_INTS_STALL_BITS; - usb_hw_clear->sie_status = USB_SIE_STATUS_STALL_REC_BITS; - hw_xfer_complete(&epx, XFER_RESULT_STALLED); - } - if (status & USB_INTS_ERROR_RX_TIMEOUT_BITS) { handled |= USB_INTS_ERROR_RX_TIMEOUT_BITS; @@ -505,6 +512,9 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * struct hw_endpoint *ep = get_dev_ep(dev_addr, ep_addr); assert(ep); + // EP should be inactive + assert(!ep->active); + // Control endpoint can change direction 0x00 <-> 0x80 if ( ep_addr != ep->ep_addr ) { @@ -552,6 +562,9 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet // Configure EP0 struct with setup info for the trans complete struct hw_endpoint *ep = _hw_endpoint_allocate(0); + // EPX should be inactive + assert(!ep->active); + // EP0 out _hw_endpoint_init(ep, dev_addr, 0x00, ep->wMaxPacketSize, 0, 0); assert(ep->configured); @@ -571,21 +584,6 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet return true; } - -//bool hcd_edpt_busy(uint8_t dev_addr, uint8_t ep_addr) -//{ -// // EPX is shared, so multiple device addresses and endpoint addresses share that -// // so if any transfer is active on epx, we are busy. Interrupt endpoints have their own -// // EPX so ep->active will only be busy if there is a pending transfer on that interrupt endpoint -// // on that device -// pico_trace("hcd_edpt_busy dev addr %d ep_addr 0x%x\n", dev_addr, ep_addr); -// struct hw_endpoint *ep = get_dev_ep(dev_addr, ep_addr); -// assert(ep); -// bool busy = ep->active; -// pico_trace("busy == %d\n", busy); -// return busy; -//} - bool hcd_edpt_clear_stall(uint8_t dev_addr, uint8_t ep_addr) { (void) dev_addr; -- cgit v1.3.1 From 05fc2fa7a64c32aa748c8c0f1fe119f417fed074 Mon Sep 17 00:00:00 2001 From: maddyaby <32046405+maddyaby@users.noreply.github.com> Date: Thu, 16 Jun 2022 16:57:20 -0700 Subject: Stub out dcd_edpt_close for samd Not having this prevents the device from finishing the mounting process. Tested on a SAMD51 and didn't seem to need to actually do anything in the close function. --- src/portable/microchip/samd/dcd_samd.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'src') diff --git a/src/portable/microchip/samd/dcd_samd.c b/src/portable/microchip/samd/dcd_samd.c index 5ae5a554b..20dbde0f4 100644 --- a/src/portable/microchip/samd/dcd_samd.c +++ b/src/portable/microchip/samd/dcd_samd.c @@ -250,6 +250,13 @@ bool dcd_edpt_open (uint8_t rhport, tusb_desc_endpoint_t const * desc_edpt) return true; } +void dcd_edpt_close (uint8_t rhport, uint8_t ep_addr) { + (void) rhport; + (void) ep_addr; + + // TODO: implement if necessary? +} + void dcd_edpt_close_all (uint8_t rhport) { (void) rhport; -- cgit v1.3.1 From 1001d2da401bc9abb98207d8f4be239ac62d5c33 Mon Sep 17 00:00:00 2001 From: mingpepe Date: Fri, 17 Jun 2022 16:50:24 +0800 Subject: Fix typo for log format --- src/portable/raspberrypi/rp2040/rp2040_usb.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'src') diff --git a/src/portable/raspberrypi/rp2040/rp2040_usb.c b/src/portable/raspberrypi/rp2040/rp2040_usb.c index f93568f0c..49be90167 100644 --- a/src/portable/raspberrypi/rp2040/rp2040_usb.c +++ b/src/portable/raspberrypi/rp2040/rp2040_usb.c @@ -174,7 +174,7 @@ static void __tusb_irq_path_func(_hw_endpoint_start_next_buffer)(struct hw_endpo *ep->endpoint_control = ep_ctrl; - TU_LOG(3, " Prepare BufCtrl: [0] = 0x%04u [1] = 0x%04x\r\n", tu_u32_low16(buf_ctrl), tu_u32_high16(buf_ctrl)); + TU_LOG(3, " Prepare BufCtrl: [0] = 0x%04x [1] = 0x%04x\r\n", tu_u32_low16(buf_ctrl), tu_u32_high16(buf_ctrl)); // Finally, write to buffer_control which will trigger the transfer // the next time the controller polls this dpram address @@ -247,7 +247,7 @@ static void __tusb_irq_path_func(_hw_endpoint_xfer_sync) (struct hw_endpoint *ep // after a buff status interrupt uint32_t __unused buf_ctrl = _hw_endpoint_buffer_control_get_value32(ep); - TU_LOG(3, " Sync BufCtrl: [0] = 0x%04u [1] = 0x%04x\r\n", tu_u32_low16(buf_ctrl), tu_u32_high16(buf_ctrl)); + TU_LOG(3, " Sync BufCtrl: [0] = 0x%04x [1] = 0x%04x\r\n", tu_u32_low16(buf_ctrl), tu_u32_high16(buf_ctrl)); // always sync buffer 0 uint16_t buf0_bytes = sync_ep_buffer(ep, 0); @@ -285,7 +285,7 @@ static void __tusb_irq_path_func(_hw_endpoint_xfer_sync) (struct hw_endpoint *ep usb_hw->abort &= ~TU_BIT(ep_id); TU_LOG(3, "----SHORT PACKET buffer0 on EP %02X:\r\n", ep->ep_addr); - TU_LOG(3, " BufCtrl: [0] = 0x%04u [1] = 0x%04x\r\n", tu_u32_low16(buf_ctrl), tu_u32_high16(buf_ctrl)); + TU_LOG(3, " BufCtrl: [0] = 0x%04x [1] = 0x%04x\r\n", tu_u32_low16(buf_ctrl), tu_u32_high16(buf_ctrl)); #endif } } -- cgit v1.3.1 From 4f6e770eda9f8c605b238f35def1edaff93a8fb8 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 24 Jun 2022 19:45:49 +0700 Subject: add more warning option, also fix -Wconversion with rp2040 -Wuninitialized, -Wunused, -Wredundant-decls --- examples/device/cdc_msc/src/usb_descriptors.c | 2 +- examples/make.mk | 7 ++++- hw/bsp/broadcom_32bit/family.mk | 2 +- hw/bsp/broadcom_64bit/family.mk | 2 +- hw/bsp/imxrt/family.mk | 2 +- hw/bsp/mm32/boards/mm32f327x_mb39/mm32f327x_mb39.c | 1 - hw/bsp/nrf/family.mk | 3 ++ hw/bsp/rx/family.mk | 3 ++ hw/bsp/samd21/family.mk | 2 +- hw/bsp/saml2x/family.mk | 2 +- hw/mcu/raspberry_pi/Pico-PIO-USB | 2 +- src/class/cdc/cdc_device.c | 6 ++-- src/class/msc/msc_device.c | 33 +++++++++++----------- src/common/tusb_fifo.c | 12 ++++---- src/device/usbd.c | 16 +++++++---- src/device/usbd_control.c | 2 +- src/portable/synopsys/dwc2/dwc2_stm32.h | 3 +- 17 files changed, 58 insertions(+), 42 deletions(-) (limited to 'src') diff --git a/examples/device/cdc_msc/src/usb_descriptors.c b/examples/device/cdc_msc/src/usb_descriptors.c index 09894cf1b..6b59ed50f 100644 --- a/examples/device/cdc_msc/src/usb_descriptors.c +++ b/examples/device/cdc_msc/src/usb_descriptors.c @@ -282,7 +282,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/make.mk b/examples/make.mk index bed46d02b..26065c027 100644 --- a/examples/make.mk +++ b/examples/make.mk @@ -108,8 +108,13 @@ CFLAGS += \ -Wcast-align \ -Wcast-function-type \ -Wcast-qual \ - -Wnull-dereference + -Wnull-dereference \ + -Wuninitialized \ + -Wunused \ + -Wredundant-decls +# -Wconversion \ + # Debugging/Optimization ifeq ($(DEBUG), 1) CFLAGS += -Og diff --git a/hw/bsp/broadcom_32bit/family.mk b/hw/bsp/broadcom_32bit/family.mk index 98744c5d0..cf68e21ee 100644 --- a/hw/bsp/broadcom_32bit/family.mk +++ b/hw/bsp/broadcom_32bit/family.mk @@ -16,7 +16,7 @@ CFLAGS += \ CROSS_COMPILE = arm-none-eabi- # mcu driver cause following warnings -CFLAGS += -Wno-error=cast-qual +CFLAGS += -Wno-error=cast-qual -Wno-error=redundant-decls SRC_C += \ src/portable/synopsys/dwc2/dcd_dwc2.c \ diff --git a/hw/bsp/broadcom_64bit/family.mk b/hw/bsp/broadcom_64bit/family.mk index 723926734..97af6d64a 100644 --- a/hw/bsp/broadcom_64bit/family.mk +++ b/hw/bsp/broadcom_64bit/family.mk @@ -15,7 +15,7 @@ CFLAGS += \ CROSS_COMPILE = aarch64-none-elf- # mcu driver cause following warnings -CFLAGS += -Wno-error=cast-qual +CFLAGS += -Wno-error=cast-qual -Wno-error=redundant-decls SRC_C += \ src/portable/synopsys/dwc2/dcd_dwc2.c \ diff --git a/hw/bsp/imxrt/family.mk b/hw/bsp/imxrt/family.mk index c81e67eb6..0a55b740b 100644 --- a/hw/bsp/imxrt/family.mk +++ b/hw/bsp/imxrt/family.mk @@ -23,7 +23,7 @@ CFLAGS += -DBOARD_TUH_RHPORT=$(BOARD_TUH_RHPORT) endif # mcu driver cause following warnings -CFLAGS += -Wno-error=unused-parameter -Wno-error=implicit-fallthrough= +CFLAGS += -Wno-error=unused-parameter -Wno-error=implicit-fallthrough -Wno-error=redundant-decls MCU_DIR = $(SDK_DIR)/devices/$(MCU_VARIANT) diff --git a/hw/bsp/mm32/boards/mm32f327x_mb39/mm32f327x_mb39.c b/hw/bsp/mm32/boards/mm32f327x_mb39/mm32f327x_mb39.c index cff7bc15e..9793ba241 100644 --- a/hw/bsp/mm32/boards/mm32f327x_mb39/mm32f327x_mb39.c +++ b/hw/bsp/mm32/boards/mm32f327x_mb39/mm32f327x_mb39.c @@ -52,7 +52,6 @@ void USB_DeviceClockInit (void) //--------------------------------------------------------------------+ // LED -void board_led_write (bool state); extern u32 SystemCoreClock; const int baudrate = 115200; diff --git a/hw/bsp/nrf/family.mk b/hw/bsp/nrf/family.mk index d8283a9e6..609e2da0b 100644 --- a/hw/bsp/nrf/family.mk +++ b/hw/bsp/nrf/family.mk @@ -16,6 +16,9 @@ CFLAGS += \ # suppress warning caused by vendor mcu driver CFLAGS += -Wno-error=undef -Wno-error=unused-parameter -Wno-error=cast-align -Wno-error=cast-qual +# warning caused by dcd_nrf5x.c due to include of usbd.h and re-declare of dcd_int_handler() +CFLAGS += -Wno-error=redundant-decls + # All source paths should be relative to the top level. LD_FILE ?= hw/bsp/nrf/boards/$(BOARD)/nrf52840_s140_v6.ld diff --git a/hw/bsp/rx/family.mk b/hw/bsp/rx/family.mk index aba05812d..f4f8ae088 100644 --- a/hw/bsp/rx/family.mk +++ b/hw/bsp/rx/family.mk @@ -13,6 +13,9 @@ CFLAGS += \ -mlittle-endian-data \ -DSSIZE_MAX=__INT_MAX__ +# suppress warning caused by vendor mcu driver +CFLAGS += -Wno-error=redundant-decls + SRC_C += \ src/portable/renesas/usba/dcd_usba.c \ src/portable/renesas/usba/hcd_usba.c \ diff --git a/hw/bsp/samd21/family.mk b/hw/bsp/samd21/family.mk index 208f23789..95421e753 100644 --- a/hw/bsp/samd21/family.mk +++ b/hw/bsp/samd21/family.mk @@ -13,7 +13,7 @@ CFLAGS += \ -DCFG_TUSB_MCU=OPT_MCU_SAMD21 # suppress warning caused by vendor mcu driver -CFLAGS += -Wno-error=cast-qual +CFLAGS += -Wno-error=cast-qual -Wno-error=redundant-decls SRC_C += \ src/portable/microchip/samd/dcd_samd.c \ diff --git a/hw/bsp/saml2x/family.mk b/hw/bsp/saml2x/family.mk index bb1faeb7f..afb0afc03 100644 --- a/hw/bsp/saml2x/family.mk +++ b/hw/bsp/saml2x/family.mk @@ -14,7 +14,7 @@ CFLAGS += \ -DCFG_TUSB_MCU=OPT_MCU_SAML22 # suppress warning caused by vendor mcu driver -CFLAGS += -Wno-error=cast-qual +CFLAGS += -Wno-error=cast-qual -Wno-error=redundant-decls SRC_C += \ src/portable/microchip/samd/dcd_samd.c \ diff --git a/hw/mcu/raspberry_pi/Pico-PIO-USB b/hw/mcu/raspberry_pi/Pico-PIO-USB index 2a9fefd6c..92bd3b4c3 160000 --- a/hw/mcu/raspberry_pi/Pico-PIO-USB +++ b/hw/mcu/raspberry_pi/Pico-PIO-USB @@ -1 +1 @@ -Subproject commit 2a9fefd6ccf42e5d8570ae83fdc54c9c875ebdd1 +Subproject commit 92bd3b4c3ad2fce36166e4a357749b6d4fe9013b diff --git a/src/class/cdc/cdc_device.c b/src/class/cdc/cdc_device.c index 7aa7a4860..fab6f0035 100644 --- a/src/class/cdc/cdc_device.c +++ b/src/class/cdc/cdc_device.c @@ -145,7 +145,7 @@ uint32_t tud_cdc_n_available(uint8_t itf) uint32_t tud_cdc_n_read(uint8_t itf, void* buffer, uint32_t bufsize) { cdcd_interface_t* p_cdc = &_cdcd_itf[itf]; - uint32_t num_read = tu_fifo_read_n(&p_cdc->rx_ff, buffer, bufsize); + uint32_t num_read = tu_fifo_read_n(&p_cdc->rx_ff, buffer, (uint16_t) bufsize); _prep_out_transaction(p_cdc); return num_read; } @@ -168,7 +168,7 @@ void tud_cdc_n_read_flush (uint8_t itf) uint32_t tud_cdc_n_write(uint8_t itf, void const* buffer, uint32_t bufsize) { cdcd_interface_t* p_cdc = &_cdcd_itf[itf]; - uint16_t ret = tu_fifo_write_n(&p_cdc->tx_ff, buffer, bufsize); + uint16_t ret = tu_fifo_write_n(&p_cdc->tx_ff, buffer, (uint16_t) bufsize); // flush if queue more than packet size if ( tu_fifo_count(&p_cdc->tx_ff) >= BULK_PACKET_SIZE ) @@ -435,7 +435,7 @@ bool cdcd_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t result, uint32_ // Received new data if ( ep_addr == p_cdc->ep_out ) { - tu_fifo_write_n(&p_cdc->rx_ff, &p_cdc->epout_buf, xferred_bytes); + tu_fifo_write_n(&p_cdc->rx_ff, &p_cdc->epout_buf, (uint16_t) xferred_bytes); // Check for wanted char and invoke callback if needed if ( tud_cdc_rx_wanted_cb && (((signed char) p_cdc->wanted_char) != -1) ) diff --git a/src/class/msc/msc_device.c b/src/class/msc/msc_device.c index 3facb76d6..33dd4ac37 100644 --- a/src/class/msc/msc_device.c +++ b/src/class/msc/msc_device.c @@ -463,7 +463,7 @@ bool mscd_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t event, uint32_t { // Didn't check for case 9 (Ho > Dn), which requires examining scsi command first // but it is OK to just receive data then responded with failed status - TU_ASSERT( usbd_edpt_xfer(rhport, p_msc->ep_out, _mscd_buf, p_msc->total_len) ); + TU_ASSERT( usbd_edpt_xfer(rhport, p_msc->ep_out, _mscd_buf, (uint16_t) p_msc->total_len) ); } }else { @@ -473,7 +473,7 @@ bool mscd_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t event, uint32_t // Invoke user callback if not built-in if ( (resplen < 0) && (p_msc->sense_key == 0) ) { - resplen = tud_msc_scsi_cb(p_cbw->lun, p_cbw->command, _mscd_buf, p_msc->total_len); + resplen = tud_msc_scsi_cb(p_cbw->lun, p_cbw->command, _mscd_buf, (uint16_t) p_msc->total_len); } if ( resplen < 0 ) @@ -506,7 +506,7 @@ bool mscd_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t event, uint32_t { // cannot return more than host expect p_msc->total_len = tu_min32((uint32_t) resplen, p_cbw->total_bytes); - TU_ASSERT( usbd_edpt_xfer(rhport, p_msc->ep_in, _mscd_buf, p_msc->total_len) ); + TU_ASSERT( usbd_edpt_xfer(rhport, p_msc->ep_in, _mscd_buf, (uint16_t) p_msc->total_len) ); } } } @@ -541,7 +541,7 @@ bool mscd_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t event, uint32_t // OUT transfer, invoke callback if needed if ( !is_data_in(p_cbw->dir) ) { - int32_t cb_result = tud_msc_scsi_cb(p_cbw->lun, p_cbw->command, _mscd_buf, p_msc->total_len); + int32_t cb_result = tud_msc_scsi_cb(p_cbw->lun, p_cbw->command, _mscd_buf, (uint16_t) p_msc->total_len); if ( cb_result < 0 ) { @@ -707,7 +707,7 @@ static int32_t proc_builtin_scsi(uint8_t lun, uint8_t const scsi_cmd[16], uint8_ read_capa10.block_size = tu_htonl(block_size); resplen = sizeof(read_capa10); - memcpy(buffer, &read_capa10, resplen); + memcpy(buffer, &read_capa10, (size_t) resplen); } } break; @@ -741,7 +741,7 @@ static int32_t proc_builtin_scsi(uint8_t lun, uint8_t const scsi_cmd[16], uint8_ read_fmt_capa.block_size_u16 = tu_htons(block_size); resplen = sizeof(read_fmt_capa); - memcpy(buffer, &read_fmt_capa, resplen); + memcpy(buffer, &read_fmt_capa, (size_t) resplen); } } break; @@ -764,7 +764,7 @@ static int32_t proc_builtin_scsi(uint8_t lun, uint8_t const scsi_cmd[16], uint8_ tud_msc_inquiry_cb(lun, inquiry_rsp.vendor_id, inquiry_rsp.product_id, inquiry_rsp.product_rev); resplen = sizeof(inquiry_rsp); - memcpy(buffer, &inquiry_rsp, resplen); + memcpy(buffer, &inquiry_rsp, (size_t) resplen); } break; @@ -788,7 +788,7 @@ static int32_t proc_builtin_scsi(uint8_t lun, uint8_t const scsi_cmd[16], uint8_ mode_resp.write_protected = !writable; resplen = sizeof(mode_resp); - memcpy(buffer, &mode_resp, resplen); + memcpy(buffer, &mode_resp, (size_t) resplen); } break; @@ -801,17 +801,17 @@ static int32_t proc_builtin_scsi(uint8_t lun, uint8_t const scsi_cmd[16], uint8_ }; sense_rsp.add_sense_len = sizeof(scsi_sense_fixed_resp_t) - 8; - sense_rsp.sense_key = p_msc->sense_key; + sense_rsp.sense_key = (uint8_t) (p_msc->sense_key & 0x0F); sense_rsp.add_sense_code = p_msc->add_sense_code; sense_rsp.add_sense_qualifier = p_msc->add_sense_qualifier; resplen = sizeof(sense_rsp); - memcpy(buffer, &sense_rsp, resplen); + memcpy(buffer, &sense_rsp, (size_t) resplen); // request sense callback could overwrite the sense data if (tud_msc_request_sense_cb) { - resplen = tud_msc_request_sense_cb(lun, buffer, bufsize); + resplen = tud_msc_request_sense_cb(lun, buffer, (uint16_t) bufsize); } // Clear sense data after copy @@ -859,7 +859,7 @@ static void proc_read10_cmd(uint8_t rhport, mscd_interface_t* p_msc) } else { - TU_ASSERT( usbd_edpt_xfer(rhport, p_msc->ep_in, _mscd_buf, nbytes), ); + TU_ASSERT( usbd_edpt_xfer(rhport, p_msc->ep_in, _mscd_buf, (uint16_t) nbytes), ); } } @@ -883,7 +883,7 @@ static void proc_write10_cmd(uint8_t rhport, mscd_interface_t* p_msc) } // remaining bytes capped at class buffer - int32_t nbytes = (int32_t) tu_min32(sizeof(_mscd_buf), p_cbw->total_bytes-p_msc->xferred_len); + uint16_t nbytes = (uint16_t) tu_min32(sizeof(_mscd_buf), p_cbw->total_bytes-p_msc->xferred_len); // Write10 callback will be called later when usb transfer complete TU_ASSERT( usbd_edpt_xfer(rhport, p_msc->ep_out, _mscd_buf, nbytes), ); @@ -921,14 +921,15 @@ static void proc_write10_new_data(uint8_t rhport, mscd_interface_t* p_msc, uint3 // Application consume less than what we got (including zero) if ( (uint32_t) nbytes < xferred_bytes ) { + uint32_t const left_over = xferred_bytes - (uint32_t) nbytes; if ( nbytes > 0 ) { - p_msc->xferred_len += nbytes; - memmove(_mscd_buf, _mscd_buf+nbytes, xferred_bytes-nbytes); + p_msc->xferred_len += (uint16_t) nbytes; + memmove(_mscd_buf, _mscd_buf+nbytes, left_over); } // simulate an transfer complete with adjusted parameters --> callback will be invoked with adjusted parameter - dcd_event_xfer_complete(rhport, p_msc->ep_out, xferred_bytes-nbytes, XFER_RESULT_SUCCESS, false); + dcd_event_xfer_complete(rhport, p_msc->ep_out, left_over, XFER_RESULT_SUCCESS, false); } else { diff --git a/src/common/tusb_fifo.c b/src/common/tusb_fifo.c index 183c9c6fc..895b9208b 100644 --- a/src/common/tusb_fifo.c +++ b/src/common/tusb_fifo.c @@ -79,7 +79,7 @@ bool tu_fifo_config(tu_fifo_t *f, void* buffer, uint16_t depth, uint16_t item_si // Limit index space to 2*depth - this allows for a fast "modulo" calculation // but limits the maximum depth to 2^16/2 = 2^15 and buffer overflows are detectable // only if overflow happens once (important for unsupervised DMA applications) - f->max_pointer_idx = 2*depth - 1; + f->max_pointer_idx = (uint16_t) (2*depth - 1); f->non_used_index_space = UINT16_MAX - f->max_pointer_idx; f->rd_idx = f->wr_idx = 0; @@ -205,7 +205,7 @@ static void _ff_push_n(tu_fifo_t* f, void const * app_buf, uint16_t n, uint16_t uint8_t rem = nLin_bytes & 0x03; if (rem > 0) { - uint8_t remrem = tu_min16(nWrap_bytes, 4-rem); + uint8_t remrem = (uint8_t) tu_min16(nWrap_bytes, 4-rem); nWrap_bytes -= remrem; uint32_t tmp32 = *rx_fifo; @@ -288,7 +288,7 @@ static void _ff_pull_n(tu_fifo_t* f, void* app_buf, uint16_t n, uint16_t rel, tu uint8_t rem = nLin_bytes & 0x03; if (rem > 0) { - uint8_t remrem = tu_min16(nWrap_bytes, 4-rem); + uint8_t remrem = (uint8_t) tu_min16(nWrap_bytes, 4-rem); nWrap_bytes -= remrem; uint32_t tmp32=0; @@ -325,7 +325,7 @@ static uint16_t advance_pointer(tu_fifo_t* f, uint16_t p, uint16_t offset) // We are exploiting the wrap around to the correct index if ((p > (uint16_t)(p + offset)) || ((uint16_t)(p + offset) > f->max_pointer_idx)) { - p = (p + offset) + f->non_used_index_space; + p = (uint16_t) ((p + offset) + f->non_used_index_space); } else { @@ -342,7 +342,7 @@ static uint16_t backward_pointer(tu_fifo_t* f, uint16_t p, uint16_t offset) // We are exploiting the wrap around to the correct index if ((p < (uint16_t)(p - offset)) || ((uint16_t)(p - offset) > f->max_pointer_idx)) { - p = (p - offset) - f->non_used_index_space; + p = (uint16_t) ((p - offset) - f->non_used_index_space); } else { @@ -818,7 +818,7 @@ bool tu_fifo_clear(tu_fifo_t *f) _ff_lock(f->mutex_rd); f->rd_idx = f->wr_idx = 0; - f->max_pointer_idx = 2*f->depth-1; + f->max_pointer_idx = (uint16_t) (2*f->depth-1); f->non_used_index_space = UINT16_MAX - f->max_pointer_idx; _ff_unlock(f->mutex_wr); diff --git a/src/device/usbd.c b/src/device/usbd.c index 1806281ff..fa894accc 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -409,6 +409,7 @@ bool tud_init (uint8_t rhport) for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) { usbd_class_driver_t const * driver = get_driver(i); + TU_ASSERT(driver); TU_LOG2("%s init\r\n", driver->name); driver->init(); } @@ -426,7 +427,9 @@ static void configuration_reset(uint8_t rhport) { for ( uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++ ) { - get_driver(i)->reset(rhport); + usbd_class_driver_t const * driver = get_driver(i); + TU_ASSERT(driver, ); + driver->reset(rhport); } tu_varclr(&_usbd_dev); @@ -735,7 +738,7 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const // Device status bit mask // - Bit 0: Self Powered // - Bit 1: Remote Wakeup enabled - uint16_t status = (_usbd_dev.self_powered ? 1 : 0) | (_usbd_dev.remote_wakeup_en ? 2 : 0); + uint16_t status = (uint16_t) ((_usbd_dev.self_powered ? 1u : 0u) | (_usbd_dev.remote_wakeup_en ? 2u : 0u)); tud_control_xfer(rhport, p_request, &status, 2); } break; @@ -867,8 +870,8 @@ static bool process_set_config(uint8_t rhport, uint8_t cfg_num) TU_ASSERT(desc_cfg != NULL && desc_cfg->bDescriptorType == TUSB_DESC_CONFIGURATION); // Parse configuration descriptor - _usbd_dev.remote_wakeup_support = (desc_cfg->bmAttributes & TUSB_DESC_CONFIG_ATT_REMOTE_WAKEUP) ? 1 : 0; - _usbd_dev.self_powered = (desc_cfg->bmAttributes & TUSB_DESC_CONFIG_ATT_SELF_POWERED ) ? 1 : 0; + _usbd_dev.remote_wakeup_support = (desc_cfg->bmAttributes & TUSB_DESC_CONFIG_ATT_REMOTE_WAKEUP) ? 1u : 0u; + _usbd_dev.self_powered = (desc_cfg->bmAttributes & TUSB_DESC_CONFIG_ATT_SELF_POWERED ) ? 1u : 0u; // Parse interface descriptor uint8_t const * p_desc = ((uint8_t const*) desc_cfg) + sizeof(tusb_desc_configuration_t); @@ -895,11 +898,12 @@ static bool process_set_config(uint8_t rhport, uint8_t cfg_num) tusb_desc_interface_t const * desc_itf = (tusb_desc_interface_t const*) p_desc; // Find driver for this interface - uint16_t const remaining_len = desc_end-p_desc; + uint16_t const remaining_len = (uint16_t) (desc_end-p_desc); uint8_t drv_id; for (drv_id = 0; drv_id < TOTAL_DRIVER_COUNT; drv_id++) { usbd_class_driver_t const *driver = get_driver(drv_id); + TU_ASSERT(driver); uint16_t const drv_len = driver->open(rhport, desc_itf, remaining_len); if ( (sizeof(tusb_desc_interface_t) <= drv_len) && (drv_len <= remaining_len) ) @@ -1101,7 +1105,7 @@ TU_ATTR_FAST_FUNC void dcd_event_handler(dcd_event_t const * event, bool in_isr) for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) { usbd_class_driver_t const * driver = get_driver(i); - if (driver->sof) + if (driver && driver->sof) { driver->sof(event->rhport, event->sof.frame_count); } diff --git a/src/device/usbd_control.c b/src/device/usbd_control.c index 4f4108090..94a952df7 100644 --- a/src/device/usbd_control.c +++ b/src/device/usbd_control.c @@ -189,7 +189,7 @@ bool usbd_control_xfer_cb (uint8_t rhport, uint8_t ep_addr, xfer_result_t result TU_LOG_MEM(2, _usbd_ctrl_buf, xferred_bytes, 2); } - _ctrl_xfer.total_xferred += xferred_bytes; + _ctrl_xfer.total_xferred += (uint16_t) xferred_bytes; _ctrl_xfer.buffer += xferred_bytes; // Data Stage is complete when all request's length are transferred or diff --git a/src/portable/synopsys/dwc2/dwc2_stm32.h b/src/portable/synopsys/dwc2/dwc2_stm32.h index b500ddc46..1d849541e 100644 --- a/src/portable/synopsys/dwc2/dwc2_stm32.h +++ b/src/portable/synopsys/dwc2/dwc2_stm32.h @@ -103,7 +103,8 @@ static const dwc2_controller_t _dwc2_controller[] = // //--------------------------------------------------------------------+ -extern uint32_t SystemCoreClock; +// SystemCoreClock is alrady included by family header +// extern uint32_t SystemCoreClock; TU_ATTR_ALWAYS_INLINE static inline void dwc2_dcd_int_enable(uint8_t rhport) -- cgit v1.3.1 From 0042eccb3b2ff0f980f3a927a271364a2089ada5 Mon Sep 17 00:00:00 2001 From: hathach Date: Fri, 24 Jun 2022 22:22:52 +0700 Subject: fix redundant-decls warnings by usbd/usbh --- examples/make.mk | 6 +++--- hw/bsp/nrf/family.mk | 3 --- src/class/msc/msc_device.c | 2 +- src/device/dcd.h | 7 ------- src/device/usbd.c | 2 +- src/device/usbd.h | 5 ++++- src/device/usbd_control.c | 2 +- src/host/hub.c | 1 + src/host/usbh.c | 3 +-- src/host/usbh.h | 6 ++++-- 10 files changed, 16 insertions(+), 21 deletions(-) (limited to 'src') diff --git a/examples/make.mk b/examples/make.mk index 26065c027..fa909ddca 100644 --- a/examples/make.mk +++ b/examples/make.mk @@ -90,13 +90,13 @@ CFLAGS += \ -ffunction-sections \ -fsingle-precision-constant \ -fno-strict-aliasing \ - -Wdouble-promotion \ - -Wstrict-prototypes \ - -Wstrict-overflow \ -Wall \ -Wextra \ -Werror \ -Wfatal-errors \ + -Wdouble-promotion \ + -Wstrict-prototypes \ + -Wstrict-overflow \ -Werror-implicit-function-declaration \ -Wfloat-equal \ -Wundef \ diff --git a/hw/bsp/nrf/family.mk b/hw/bsp/nrf/family.mk index 609e2da0b..d8283a9e6 100644 --- a/hw/bsp/nrf/family.mk +++ b/hw/bsp/nrf/family.mk @@ -16,9 +16,6 @@ CFLAGS += \ # suppress warning caused by vendor mcu driver CFLAGS += -Wno-error=undef -Wno-error=unused-parameter -Wno-error=cast-align -Wno-error=cast-qual -# warning caused by dcd_nrf5x.c due to include of usbd.h and re-declare of dcd_int_handler() -CFLAGS += -Wno-error=redundant-decls - # All source paths should be relative to the top level. LD_FILE ?= hw/bsp/nrf/boards/$(BOARD)/nrf52840_s140_v6.ld diff --git a/src/class/msc/msc_device.c b/src/class/msc/msc_device.c index 33dd4ac37..00b0a1d06 100644 --- a/src/class/msc/msc_device.c +++ b/src/class/msc/msc_device.c @@ -28,9 +28,9 @@ #if (CFG_TUD_ENABLED && CFG_TUD_MSC) +#include "device/dcd.h" // for faking dcd_event_xfer_complete #include "device/usbd.h" #include "device/usbd_pvt.h" -#include "device/dcd.h" // for faking dcd_event_xfer_complete #include "msc_device.h" diff --git a/src/device/dcd.h b/src/device/dcd.h index 6b99734fe..c1780f656 100644 --- a/src/device/dcd.h +++ b/src/device/dcd.h @@ -110,14 +110,7 @@ typedef struct TU_ATTR_ALIGNED(4) void dcd_init (uint8_t rhport); // Interrupt Handler -#if __GNUC__ && !defined(__ARMCC_VERSION) -#pragma GCC diagnostic push -#pragma GCC diagnostic ignored "-Wredundant-decls" -#endif void dcd_int_handler(uint8_t rhport); -#if __GNUC__ && !defined(__ARMCC_VERSION) -#pragma GCC diagnostic pop -#endif // Enable device interrupt void dcd_int_enable (uint8_t rhport); diff --git a/src/device/usbd.c b/src/device/usbd.c index fa894accc..b2053174e 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -28,12 +28,12 @@ #if CFG_TUD_ENABLED +#include "device/dcd.h" #include "tusb.h" #include "common/tusb_private.h" #include "device/usbd.h" #include "device/usbd_pvt.h" -#include "device/dcd.h" //--------------------------------------------------------------------+ // USBD Configuration diff --git a/src/device/usbd.h b/src/device/usbd.h index 964cfb992..17b4d927b 100644 --- a/src/device/usbd.h +++ b/src/device/usbd.h @@ -58,8 +58,11 @@ void tud_task (void) // Check if there is pending events need processing by tud_task() bool tud_task_event_ready(void); -// Interrupt handler, name alias to DCD +#ifndef _TUSB_DCD_H_ extern void dcd_int_handler(uint8_t rhport); +#endif + +// Interrupt handler, name alias to DCD #define tud_int_handler dcd_int_handler // Get current bus speed diff --git a/src/device/usbd_control.c b/src/device/usbd_control.c index 94a952df7..0995ef669 100644 --- a/src/device/usbd_control.c +++ b/src/device/usbd_control.c @@ -28,9 +28,9 @@ #if CFG_TUD_ENABLED +#include "dcd.h" #include "tusb.h" #include "device/usbd_pvt.h" -#include "dcd.h" #if CFG_TUSB_DEBUG >= 2 extern void usbd_driver_print_control_complete_name(usbd_control_xfer_cb_t callback); diff --git a/src/host/hub.c b/src/host/hub.c index 5c0fd9166..3400b154a 100644 --- a/src/host/hub.c +++ b/src/host/hub.c @@ -28,6 +28,7 @@ #if (CFG_TUH_ENABLED && CFG_TUH_HUB) +#include "hcd.h" #include "usbh.h" #include "usbh_classdriver.h" #include "hub.h" diff --git a/src/host/usbh.c b/src/host/usbh.c index 4807d20b8..4c9b0b1ba 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -28,10 +28,9 @@ #if CFG_TUH_ENABLED +#include "host/hcd.h" #include "tusb.h" #include "common/tusb_private.h" - -#include "host/usbh.h" #include "host/usbh_classdriver.h" #include "hub.h" diff --git a/src/host/usbh.h b/src/host/usbh.h index 347c75b8c..560a1ea23 100644 --- a/src/host/usbh.h +++ b/src/host/usbh.h @@ -32,7 +32,6 @@ #endif #include "common/tusb_common.h" -#include "hcd.h" //--------------------------------------------------------------------+ // MACRO CONSTANT TYPEDEF @@ -115,8 +114,11 @@ void tuh_task(void) tuh_task_ext(UINT32_MAX, false); } -// Interrupt handler, name alias to HCD +#ifndef _TUSB_HCD_H_ extern void hcd_int_handler(uint8_t rhport); +#endif + +// Interrupt handler, name alias to HCD #define tuh_int_handler hcd_int_handler bool tuh_vid_pid_get(uint8_t daddr, uint16_t* vid, uint16_t* pid); -- cgit v1.3.1 From b9dc9dbd78ee1890342429502d585f323c480fc2 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 27 Jun 2022 11:50:17 +0700 Subject: fix most warnings with rp2040 -wconversion --- examples/device/audio_4_channel_mic/CMakeLists.txt | 3 +++ examples/device/audio_4_channel_mic/src/main.c | 2 +- .../audio_4_channel_mic/src/usb_descriptors.c | 4 ++-- examples/device/audio_test/CMakeLists.txt | 3 +++ examples/device/audio_test/src/main.c | 2 +- examples/device/audio_test/src/usb_descriptors.c | 4 ++-- examples/device/board_test/CMakeLists.txt | 3 +++ examples/device/cdc_dual_ports/CMakeLists.txt | 3 +++ .../device/cdc_dual_ports/src/usb_descriptors.c | 4 ++-- examples/device/cdc_msc/CMakeLists.txt | 3 +++ .../device/cdc_msc_freertos/src/usb_descriptors.c | 4 ++-- examples/device/dfu/CMakeLists.txt | 5 ++++- examples/device/dfu/src/usb_descriptors.c | 2 +- examples/device/dfu_runtime/CMakeLists.txt | 3 +++ examples/device/dfu_runtime/src/usb_descriptors.c | 4 ++-- .../device/dynamic_configuration/CMakeLists.txt | 3 +++ examples/device/dynamic_configuration/src/main.c | 2 +- .../device/dynamic_configuration/src/msc_disk.c | 6 +++--- .../dynamic_configuration/src/usb_descriptors.c | 4 ++-- examples/device/hid_boot_interface/CMakeLists.txt | 3 +++ .../hid_boot_interface/src/usb_descriptors.c | 4 ++-- examples/device/hid_composite/CMakeLists.txt | 3 +++ .../device/hid_composite/src/usb_descriptors.c | 4 ++-- .../hid_composite_freertos/src/usb_descriptors.c | 4 ++-- examples/device/hid_generic_inout/CMakeLists.txt | 3 +++ .../device/hid_generic_inout/src/usb_descriptors.c | 4 ++-- .../device/hid_multiple_interface/CMakeLists.txt | 3 +++ .../hid_multiple_interface/src/usb_descriptors.c | 4 ++-- examples/device/midi_test/CMakeLists.txt | 3 +++ examples/device/midi_test/src/usb_descriptors.c | 4 ++-- examples/device/msc_dual_lun/CMakeLists.txt | 3 +++ examples/device/msc_dual_lun/src/usb_descriptors.c | 4 ++-- examples/device/net_lwip_webserver/CMakeLists.txt | 3 +++ .../net_lwip_webserver/src/usb_descriptors.c | 4 ++-- examples/device/uac2_headset/CMakeLists.txt | 3 +++ examples/device/uac2_headset/src/usb_descriptors.c | 2 +- examples/device/usbtmc/CMakeLists.txt | 3 +++ examples/device/usbtmc/src/usb_descriptors.c | 2 +- examples/device/video_capture/CMakeLists.txt | 3 +++ .../device/video_capture/src/usb_descriptors.c | 4 ++-- examples/device/webusb_serial/CMakeLists.txt | 3 +++ .../device/webusb_serial/src/usb_descriptors.c | 4 ++-- .../host_hid_to_device_cdc/src/usb_descriptors.c | 2 +- examples/example.cmake | 25 ++++++++++++++++++++++ hw/bsp/rp2040/family.c | 6 +++++- src/class/audio/audio_device.c | 2 +- src/class/hid/hid_device.c | 5 +++-- src/class/midi/midi_device.c | 12 +++++------ 48 files changed, 140 insertions(+), 53 deletions(-) create mode 100644 examples/example.cmake (limited to 'src') diff --git a/examples/device/audio_4_channel_mic/CMakeLists.txt b/examples/device/audio_4_channel_mic/CMakeLists.txt index f6e10e2ea..e6ce2813e 100644 --- a/examples/device/audio_4_channel_mic/CMakeLists.txt +++ b/examples/device/audio_4_channel_mic/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) diff --git a/examples/device/audio_4_channel_mic/src/main.c b/examples/device/audio_4_channel_mic/src/main.c index 9c94edd49..a6af5fd19 100644 --- a/examples/device/audio_4_channel_mic/src/main.c +++ b/examples/device/audio_4_channel_mic/src/main.c @@ -221,7 +221,7 @@ bool tud_audio_set_req_entity_cb(uint8_t rhport, tusb_control_request_t const * // Request uses format layout 2 TU_VERIFY(p_request->wLength == sizeof(audio_control_cur_2_t)); - volume[channelNum] = ((audio_control_cur_2_t*) pBuff)->bCur; + volume[channelNum] = (uint16_t) ((audio_control_cur_2_t*) pBuff)->bCur; TU_LOG2(" Set Volume: %d dB of channel: %u\r\n", volume[channelNum], channelNum); return true; diff --git a/examples/device/audio_4_channel_mic/src/usb_descriptors.c b/examples/device/audio_4_channel_mic/src/usb_descriptors.c index 93ae2ea47..8929f3057 100644 --- a/examples/device/audio_4_channel_mic/src/usb_descriptors.c +++ b/examples/device/audio_4_channel_mic/src/usb_descriptors.c @@ -149,7 +149,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; for(uint8_t i=0; iwLength == sizeof(audio_control_cur_2_t)); - volume[channelNum] = ((audio_control_cur_2_t*) pBuff)->bCur; + volume[channelNum] = (uint16_t) ((audio_control_cur_2_t*) pBuff)->bCur; TU_LOG2(" Set Volume: %d dB of channel: %u\r\n", volume[channelNum], channelNum); return true; diff --git a/examples/device/audio_test/src/usb_descriptors.c b/examples/device/audio_test/src/usb_descriptors.c index 09b2a2d45..da3e203d7 100644 --- a/examples/device/audio_test/src/usb_descriptors.c +++ b/examples/device/audio_test/src/usb_descriptors.c @@ -149,7 +149,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; for(uint8_t i=0; i 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -247,7 +247,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/cdc_msc/CMakeLists.txt b/examples/device/cdc_msc/CMakeLists.txt index fa6e83b7e..04c7c1b26 100644 --- a/examples/device/cdc_msc/CMakeLists.txt +++ b/examples/device/cdc_msc/CMakeLists.txt @@ -24,6 +24,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/cdc_msc_freertos/src/usb_descriptors.c b/examples/device/cdc_msc_freertos/src/usb_descriptors.c index 9585822a3..30a712275 100644 --- a/examples/device/cdc_msc_freertos/src/usb_descriptors.c +++ b/examples/device/cdc_msc_freertos/src/usb_descriptors.c @@ -247,7 +247,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -258,7 +258,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/dfu/CMakeLists.txt b/examples/device/dfu/CMakeLists.txt index abc4d91da..121ab3852 100644 --- a/examples/device/dfu/CMakeLists.txt +++ b/examples/device/dfu/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. -family_configure_device_example(${PROJECT}) \ No newline at end of file +family_configure_device_example(${PROJECT}) diff --git a/examples/device/dfu/src/usb_descriptors.c b/examples/device/dfu/src/usb_descriptors.c index 350334aa5..51a0d09f5 100644 --- a/examples/device/dfu/src/usb_descriptors.c +++ b/examples/device/dfu/src/usb_descriptors.c @@ -152,7 +152,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) { chr_count = 31; } diff --git a/examples/device/dfu_runtime/CMakeLists.txt b/examples/device/dfu_runtime/CMakeLists.txt index abc4d91da..438635958 100644 --- a/examples/device/dfu_runtime/CMakeLists.txt +++ b/examples/device/dfu_runtime/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/dfu_runtime/src/usb_descriptors.c b/examples/device/dfu_runtime/src/usb_descriptors.c index 060943289..1b0a60551 100644 --- a/examples/device/dfu_runtime/src/usb_descriptors.c +++ b/examples/device/dfu_runtime/src/usb_descriptors.c @@ -147,7 +147,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) { chr_count = 31; } @@ -160,7 +160,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (uint16_t)((((uint16_t)TUSB_DESC_STRING) << 8 ) | (2u*chr_count + 2u)); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/dynamic_configuration/CMakeLists.txt b/examples/device/dynamic_configuration/CMakeLists.txt index fa6e83b7e..04c7c1b26 100644 --- a/examples/device/dynamic_configuration/CMakeLists.txt +++ b/examples/device/dynamic_configuration/CMakeLists.txt @@ -24,6 +24,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/dynamic_configuration/src/main.c b/examples/device/dynamic_configuration/src/main.c index 95f8b8286..33a603343 100644 --- a/examples/device/dynamic_configuration/src/main.c +++ b/examples/device/dynamic_configuration/src/main.c @@ -181,7 +181,7 @@ void midi_task(void) start_ms += 286; // Previous positions in the note sequence. - int previous = note_pos - 1; + int previous = (int) (note_pos - 1); // If we currently are at position 0, set the // previous position to the last note in the sequence. diff --git a/examples/device/dynamic_configuration/src/msc_disk.c b/examples/device/dynamic_configuration/src/msc_disk.c index a895f4738..e8cb03fdd 100644 --- a/examples/device/dynamic_configuration/src/msc_disk.c +++ b/examples/device/dynamic_configuration/src/msc_disk.c @@ -184,7 +184,7 @@ int32_t tud_msc_read10_cb(uint8_t lun, uint32_t lba, uint32_t offset, void* buff uint8_t const* addr = msc_disk[lba] + offset; memcpy(buffer, addr, bufsize); - return bufsize; + return (int32_t) bufsize; } // Callback invoked when received WRITE10 command. @@ -203,7 +203,7 @@ int32_t tud_msc_write10_cb(uint8_t lun, uint32_t lba, uint32_t offset, uint8_t* (void) lba; (void) offset; (void) buffer; #endif - return bufsize; + return (int32_t) bufsize; } // Callback invoked when received an SCSI command not in built-in list below @@ -237,7 +237,7 @@ int32_t tud_msc_scsi_cb (uint8_t lun, uint8_t const scsi_cmd[16], void* buffer, { if(in_xfer) { - memcpy(buffer, response, resplen); + memcpy(buffer, response, (size_t) resplen); }else { // SCSI output diff --git a/examples/device/dynamic_configuration/src/usb_descriptors.c b/examples/device/dynamic_configuration/src/usb_descriptors.c index b88f20163..457f774d0 100644 --- a/examples/device/dynamic_configuration/src/usb_descriptors.c +++ b/examples/device/dynamic_configuration/src/usb_descriptors.c @@ -226,7 +226,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -237,7 +237,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/hid_boot_interface/CMakeLists.txt b/examples/device/hid_boot_interface/CMakeLists.txt index abc4d91da..438635958 100644 --- a/examples/device/hid_boot_interface/CMakeLists.txt +++ b/examples/device/hid_boot_interface/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/hid_boot_interface/src/usb_descriptors.c b/examples/device/hid_boot_interface/src/usb_descriptors.c index 3fa48d98d..a0d7e9f15 100644 --- a/examples/device/hid_boot_interface/src/usb_descriptors.c +++ b/examples/device/hid_boot_interface/src/usb_descriptors.c @@ -163,7 +163,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -174,7 +174,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/hid_composite/CMakeLists.txt b/examples/device/hid_composite/CMakeLists.txt index abc4d91da..438635958 100644 --- a/examples/device/hid_composite/CMakeLists.txt +++ b/examples/device/hid_composite/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/hid_composite/src/usb_descriptors.c b/examples/device/hid_composite/src/usb_descriptors.c index e760b20ba..2988baee2 100644 --- a/examples/device/hid_composite/src/usb_descriptors.c +++ b/examples/device/hid_composite/src/usb_descriptors.c @@ -210,7 +210,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -221,7 +221,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/hid_composite_freertos/src/usb_descriptors.c b/examples/device/hid_composite_freertos/src/usb_descriptors.c index 791813fdf..4df12d3db 100644 --- a/examples/device/hid_composite_freertos/src/usb_descriptors.c +++ b/examples/device/hid_composite_freertos/src/usb_descriptors.c @@ -208,7 +208,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -219,7 +219,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/hid_generic_inout/CMakeLists.txt b/examples/device/hid_generic_inout/CMakeLists.txt index abc4d91da..438635958 100644 --- a/examples/device/hid_generic_inout/CMakeLists.txt +++ b/examples/device/hid_generic_inout/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/hid_generic_inout/src/usb_descriptors.c b/examples/device/hid_generic_inout/src/usb_descriptors.c index 5dabf42a3..c2b4792c8 100644 --- a/examples/device/hid_generic_inout/src/usb_descriptors.c +++ b/examples/device/hid_generic_inout/src/usb_descriptors.c @@ -153,7 +153,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -164,7 +164,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/hid_multiple_interface/CMakeLists.txt b/examples/device/hid_multiple_interface/CMakeLists.txt index abc4d91da..438635958 100644 --- a/examples/device/hid_multiple_interface/CMakeLists.txt +++ b/examples/device/hid_multiple_interface/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/hid_multiple_interface/src/usb_descriptors.c b/examples/device/hid_multiple_interface/src/usb_descriptors.c index 9eef21504..42471a961 100644 --- a/examples/device/hid_multiple_interface/src/usb_descriptors.c +++ b/examples/device/hid_multiple_interface/src/usb_descriptors.c @@ -171,7 +171,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -182,7 +182,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/midi_test/CMakeLists.txt b/examples/device/midi_test/CMakeLists.txt index abc4d91da..438635958 100644 --- a/examples/device/midi_test/CMakeLists.txt +++ b/examples/device/midi_test/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/midi_test/src/usb_descriptors.c b/examples/device/midi_test/src/usb_descriptors.c index 8444237c6..c84a873b1 100644 --- a/examples/device/midi_test/src/usb_descriptors.c +++ b/examples/device/midi_test/src/usb_descriptors.c @@ -166,7 +166,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -177,7 +177,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/msc_dual_lun/CMakeLists.txt b/examples/device/msc_dual_lun/CMakeLists.txt index 9e834ae21..518eac3ad 100644 --- a/examples/device/msc_dual_lun/CMakeLists.txt +++ b/examples/device/msc_dual_lun/CMakeLists.txt @@ -24,6 +24,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/msc_dual_lun/src/usb_descriptors.c b/examples/device/msc_dual_lun/src/usb_descriptors.c index 2afd391af..68a671c91 100644 --- a/examples/device/msc_dual_lun/src/usb_descriptors.c +++ b/examples/device/msc_dual_lun/src/usb_descriptors.c @@ -168,7 +168,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -179,7 +179,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/net_lwip_webserver/CMakeLists.txt b/examples/device/net_lwip_webserver/CMakeLists.txt index 8e3f0f5a8..5bb091a4f 100644 --- a/examples/device/net_lwip_webserver/CMakeLists.txt +++ b/examples/device/net_lwip_webserver/CMakeLists.txt @@ -69,6 +69,9 @@ if (EXISTS ${TOP}/lib/lwip/src) ${TOP}/lib/networking/rndis_reports.c ) + # Example common such as compiler warnings + include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) diff --git a/examples/device/net_lwip_webserver/src/usb_descriptors.c b/examples/device/net_lwip_webserver/src/usb_descriptors.c index 2b4b2a0c3..bee51790a 100644 --- a/examples/device/net_lwip_webserver/src/usb_descriptors.c +++ b/examples/device/net_lwip_webserver/src/usb_descriptors.c @@ -231,7 +231,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > (TU_ARRAY_SIZE(_desc_str) - 1)) chr_count = TU_ARRAY_SIZE(_desc_str) - 1; // Convert ASCII string into UTF-16 @@ -242,7 +242,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/uac2_headset/CMakeLists.txt b/examples/device/uac2_headset/CMakeLists.txt index abc4d91da..438635958 100644 --- a/examples/device/uac2_headset/CMakeLists.txt +++ b/examples/device/uac2_headset/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/uac2_headset/src/usb_descriptors.c b/examples/device/uac2_headset/src/usb_descriptors.c index 9e97845b8..a2d6368bf 100644 --- a/examples/device/uac2_headset/src/usb_descriptors.c +++ b/examples/device/uac2_headset/src/usb_descriptors.c @@ -155,7 +155,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if (chr_count > 31) chr_count = 31; for (uint8_t i = 0; i < chr_count; i++) diff --git a/examples/device/usbtmc/CMakeLists.txt b/examples/device/usbtmc/CMakeLists.txt index c49603c26..74f81b24f 100644 --- a/examples/device/usbtmc/CMakeLists.txt +++ b/examples/device/usbtmc/CMakeLists.txt @@ -24,6 +24,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/usbtmc/src/usb_descriptors.c b/examples/device/usbtmc/src/usb_descriptors.c index 423482634..770a97436 100644 --- a/examples/device/usbtmc/src/usb_descriptors.c +++ b/examples/device/usbtmc/src/usb_descriptors.c @@ -175,7 +175,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) { chr_count = 31; } diff --git a/examples/device/video_capture/CMakeLists.txt b/examples/device/video_capture/CMakeLists.txt index cb321f9a8..416b91665 100644 --- a/examples/device/video_capture/CMakeLists.txt +++ b/examples/device/video_capture/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/video_capture/src/usb_descriptors.c b/examples/device/video_capture/src/usb_descriptors.c index da8ec8e89..5c97f4fe1 100644 --- a/examples/device/video_capture/src/usb_descriptors.c +++ b/examples/device/video_capture/src/usb_descriptors.c @@ -149,7 +149,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -160,7 +160,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/device/webusb_serial/CMakeLists.txt b/examples/device/webusb_serial/CMakeLists.txt index abc4d91da..438635958 100644 --- a/examples/device/webusb_serial/CMakeLists.txt +++ b/examples/device/webusb_serial/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_device_example(${PROJECT}) \ No newline at end of file diff --git a/examples/device/webusb_serial/src/usb_descriptors.c b/examples/device/webusb_serial/src/usb_descriptors.c index 93e802a90..cafe2c22b 100644 --- a/examples/device/webusb_serial/src/usb_descriptors.c +++ b/examples/device/webusb_serial/src/usb_descriptors.c @@ -235,7 +235,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) const char* str = string_desc_arr[index]; // Cap at max char - chr_count = strlen(str); + chr_count = (uint8_t) strlen(str); if ( chr_count > 31 ) chr_count = 31; // Convert ASCII string into UTF-16 @@ -246,7 +246,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/dual/host_hid_to_device_cdc/src/usb_descriptors.c b/examples/dual/host_hid_to_device_cdc/src/usb_descriptors.c index e55899f65..6b0a89127 100644 --- a/examples/dual/host_hid_to_device_cdc/src/usb_descriptors.c +++ b/examples/dual/host_hid_to_device_cdc/src/usb_descriptors.c @@ -259,7 +259,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2*chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/examples/example.cmake b/examples/example.cmake new file mode 100644 index 000000000..6bb82a56d --- /dev/null +++ b/examples/example.cmake @@ -0,0 +1,25 @@ +target_compile_options(${PROJECT} PUBLIC + -Wall + -Wextra + -Werror + -Wfatal-errors + -Wdouble-promotion + #-Wstrict-prototypes + -Wstrict-overflow + #-Werror-implicit-function-declaration + -Wfloat-equal + #-Wundef + -Wshadow + -Wwrite-strings + -Wsign-compare + -Wmissing-format-attribute + -Wunreachable-code + -Wcast-align + -Wcast-function-type + -Wcast-qual + -Wnull-dereference + -Wuninitialized + -Wunused + -Wredundant-decls + -Wconversion + ) diff --git a/hw/bsp/rp2040/family.c b/hw/bsp/rp2040/family.c index 68c9e2d52..90e2192c0 100644 --- a/hw/bsp/rp2040/family.c +++ b/hw/bsp/rp2040/family.c @@ -53,7 +53,7 @@ // // This doesn't work if others are trying to access flash at the same time, // e.g. XIP streamer, or the other core. -bool __no_inline_not_in_flash_func(get_bootsel_button)() { +bool __no_inline_not_in_flash_func(get_bootsel_button)(void) { const uint CS_PIN_INDEX = 1; // Must disable interrupts, as interrupt handlers may be in flash, and we @@ -170,6 +170,8 @@ void board_init(void) void board_led_write(bool state) { + (void) state; + #ifdef LED_PIN gpio_put(LED_PIN, state ? LED_STATE_ON : (1-LED_STATE_ON)); #endif @@ -192,6 +194,7 @@ int board_uart_read(uint8_t* buf, int len) } return len; #else + (void) buf; (void) len; return 0; #endif } @@ -205,6 +208,7 @@ int board_uart_write(void const * buf, int len) } return len; #else + (void) buf; (void) len; return 0; #endif } diff --git a/src/class/audio/audio_device.c b/src/class/audio/audio_device.c index dbd8ab54b..e13e4a46c 100644 --- a/src/class/audio/audio_device.c +++ b/src/class/audio/audio_device.c @@ -1619,7 +1619,7 @@ static bool audiod_set_interface(uint8_t rhport, tusb_control_request_t const * // Reconfigure size of support FIFOs - this is necessary to avoid samples to get split in case of a wrap #if CFG_TUD_AUDIO_ENABLE_TYPE_I_ENCODING - const uint16_t active_fifo_depth = (audio->tx_supp_ff_sz_max / audio->n_bytes_per_sampe_tx) * audio->n_bytes_per_sampe_tx; + const uint16_t active_fifo_depth = (uint16_t) ((audio->tx_supp_ff_sz_max / audio->n_bytes_per_sampe_tx) * audio->n_bytes_per_sampe_tx); for (uint8_t cnt = 0; cnt < audio->n_tx_supp_ff; cnt++) { tu_fifo_config(&audio->tx_supp_ff[cnt], audio->tx_supp_ff[cnt].buffer, active_fifo_depth, 1, true); diff --git a/src/class/hid/hid_device.c b/src/class/hid/hid_device.c index cdf155e1c..d15d44838 100644 --- a/src/class/hid/hid_device.c +++ b/src/class/hid/hid_device.c @@ -187,7 +187,8 @@ uint16_t hidd_open(uint8_t rhport, tusb_desc_interface_t const * desc_itf, uint1 TU_VERIFY(TUSB_CLASS_HID == desc_itf->bInterfaceClass, 0); // len = interface + hid + n*endpoints - uint16_t const drv_len = sizeof(tusb_desc_interface_t) + sizeof(tusb_hid_descriptor_hid_t) + desc_itf->bNumEndpoints*sizeof(tusb_desc_endpoint_t); + uint16_t const drv_len = (uint16_t) (sizeof(tusb_desc_interface_t) + sizeof(tusb_hid_descriptor_hid_t) + + desc_itf->bNumEndpoints * sizeof(tusb_desc_endpoint_t)); TU_ASSERT(max_len >= drv_len, 0); // Find available interface @@ -408,7 +409,7 @@ bool hidd_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t result, uint32_ // Received report else if (ep_addr == p_hid->ep_out) { - tud_hid_set_report_cb(instance, 0, HID_REPORT_TYPE_INVALID, p_hid->epout_buf, xferred_bytes); + tud_hid_set_report_cb(instance, 0, HID_REPORT_TYPE_INVALID, p_hid->epout_buf, (uint16_t) xferred_bytes); TU_ASSERT(usbd_edpt_xfer(rhport, p_hid->ep_out, p_hid->epout_buf, sizeof(p_hid->epout_buf))); } diff --git a/src/class/midi/midi_device.c b/src/class/midi/midi_device.c index 28e6a92d2..de41706e8 100644 --- a/src/class/midi/midi_device.c +++ b/src/class/midi/midi_device.c @@ -127,7 +127,7 @@ uint32_t tud_midi_n_available(uint8_t itf, uint8_t cable_num) midid_stream_t const* stream = &midi->stream_read; // when using with packet API stream total & index are both zero - return tu_fifo_count(&midi->rx_ff) + (stream->total - stream->index); + return tu_fifo_count(&midi->rx_ff) + (uint8_t) (stream->total - stream->index); } uint32_t tud_midi_n_stream_read(uint8_t itf, uint8_t cable_num, void* buffer, uint32_t bufsize) @@ -179,7 +179,7 @@ uint32_t tud_midi_n_stream_read(uint8_t itf, uint8_t cable_num, void* buffer, ui } // Copy data up to bufsize - uint32_t const count = tu_min32(stream->total - stream->index, bufsize); + uint8_t const count = (uint8_t) tu_min32(stream->total - stream->index, bufsize); // Skip the header (1st byte) in the buffer memcpy(buf8, stream->buffer + 1 + stream->index, count); @@ -276,13 +276,13 @@ uint32_t tud_midi_n_stream_write(uint8_t itf, uint8_t cable_num, uint8_t const* else if ( (msg >= 0x8 && msg <= 0xB) || msg == 0xE ) { // Channel Voice Messages - stream->buffer[0] = (cable_num << 4) | msg; + stream->buffer[0] = (uint8_t) ((cable_num << 4) | msg); stream->total = 4; } else if ( msg == 0xC || msg == 0xD) { // Channel Voice Messages, two-byte variants (Program Change and Channel Pressure) - stream->buffer[0] = (cable_num << 4) | msg; + stream->buffer[0] = (uint8_t) ((cable_num << 4) | msg); stream->total = 3; } else if ( msg == 0xf ) @@ -312,7 +312,7 @@ uint32_t tud_midi_n_stream_write(uint8_t itf, uint8_t cable_num, uint8_t const* else { // Pack individual bytes if we don't support packing them into words. - stream->buffer[0] = cable_num << 4 | 0xf; + stream->buffer[0] = (uint8_t) (cable_num << 4 | 0xf); stream->buffer[2] = 0; stream->buffer[3] = 0; stream->index = 2; @@ -513,7 +513,7 @@ bool midid_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t result, uint32 // receive new data if ( ep_addr == p_midi->ep_out ) { - tu_fifo_write_n(&p_midi->rx_ff, p_midi->epout_buf, xferred_bytes); + tu_fifo_write_n(&p_midi->rx_ff, p_midi->epout_buf, (uint16_t) xferred_bytes); // invoke receive callback if available if (tud_midi_rx_cb) tud_midi_rx_cb(itf); -- cgit v1.3.1 From 0b3503cb33e6a269e573a75b6ed67d69aee12dbb Mon Sep 17 00:00:00 2001 From: hathach Date: Thu, 16 Jun 2022 12:01:19 +0700 Subject: clean up usbd log level --- examples/host/bare_api/src/main.c | 4 +-- src/device/usbd.c | 68 +++++++++++++++++++-------------------- 2 files changed, 36 insertions(+), 36 deletions(-) (limited to 'src') diff --git a/examples/host/bare_api/src/main.c b/examples/host/bare_api/src/main.c index 2cc05d34d..9ccd856d4 100644 --- a/examples/host/bare_api/src/main.c +++ b/examples/host/bare_api/src/main.c @@ -84,8 +84,8 @@ void tuh_mount_cb (uint8_t daddr) { printf("Device attached, address = %d\r\n", daddr); - // Get Device Descriptor sync API - // TODO: invoking control trannsfer now has issue with mounting hub with multiple devices attached, fix later + // Get Device Descriptor + // TODO: invoking control transfer now has issue with mounting hub with multiple devices attached, fix later tuh_descriptor_get_device(daddr, &desc_device, 18, print_device_descriptor, 0); } diff --git a/src/device/usbd.c b/src/device/usbd.c index 1806281ff..59d0e86e3 100644 --- a/src/device/usbd.c +++ b/src/device/usbd.c @@ -318,7 +318,7 @@ void usbd_driver_print_control_complete_name(usbd_control_xfer_cb_t callback) usbd_class_driver_t const * driver = get_driver(i); if ( driver->control_xfer_cb == callback ) { - TU_LOG2(" %s control complete\r\n", driver->name); + TU_LOG(USBD_DBG, " %s control complete\r\n", driver->name); return; } } @@ -384,8 +384,8 @@ bool tud_init (uint8_t rhport) // skip if already initialized if ( tud_inited() ) return true; - TU_LOG2("USBD init on controller %u\r\n", rhport); - TU_LOG2_INT(sizeof(usbd_device_t)); + TU_LOG(USBD_DBG, "USBD init on controller %u\r\n", rhport); + TU_LOG_INT(USBD_DBG, sizeof(usbd_device_t)); tu_varclr(&_usbd_dev); @@ -409,7 +409,7 @@ bool tud_init (uint8_t rhport) for (uint8_t i = 0; i < TOTAL_DRIVER_COUNT; i++) { usbd_class_driver_t const * driver = get_driver(i); - TU_LOG2("%s init\r\n", driver->name); + TU_LOG(USBD_DBG, "%s init\r\n", driver->name); driver->init(); } @@ -480,20 +480,20 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) if ( !osal_queue_receive(_usbd_q, &event, timeout_ms) ) return; #if CFG_TUSB_DEBUG >= 2 - if (event.event_id == DCD_EVENT_SETUP_RECEIVED) TU_LOG2("\r\n"); // extra line for setup - TU_LOG2("USBD %s ", event.event_id < DCD_EVENT_COUNT ? _usbd_event_str[event.event_id] : "CORRUPTED"); + if (event.event_id == DCD_EVENT_SETUP_RECEIVED) TU_LOG(USBD_DBG, "\r\n"); // extra line for setup + TU_LOG(USBD_DBG, "USBD %s ", event.event_id < DCD_EVENT_COUNT ? _usbd_event_str[event.event_id] : "CORRUPTED"); #endif switch ( event.event_id ) { case DCD_EVENT_BUS_RESET: - TU_LOG2(": %s Speed\r\n", tu_str_speed[event.bus_reset.speed]); + TU_LOG(USBD_DBG, ": %s Speed\r\n", tu_str_speed[event.bus_reset.speed]); usbd_reset(event.rhport); _usbd_dev.speed = event.bus_reset.speed; break; case DCD_EVENT_UNPLUGGED: - TU_LOG2("\r\n"); + TU_LOG(USBD_DBG, "\r\n"); usbd_reset(event.rhport); // invoke callback @@ -501,8 +501,8 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) break; case DCD_EVENT_SETUP_RECEIVED: - TU_LOG2_VAR(&event.setup_received); - TU_LOG2("\r\n"); + TU_LOG_VAR(USBD_DBG, &event.setup_received); + TU_LOG(USBD_DBG, "\r\n"); // Mark as connected after receiving 1st setup packet. // But it is easier to set it every time instead of wasting time to check then set @@ -517,7 +517,7 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) // Process control request if ( !process_control_request(event.rhport, &event.setup_received) ) { - TU_LOG2(" Stall EP0\r\n"); + TU_LOG(USBD_DBG, " Stall EP0\r\n"); // Failed -> stall both control endpoint IN and OUT dcd_edpt_stall(event.rhport, 0); dcd_edpt_stall(event.rhport, 0 | TUSB_DIR_IN_MASK); @@ -531,7 +531,7 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const ep_dir = tu_edpt_dir(ep_addr); - TU_LOG2("on EP %02X with %u bytes\r\n", ep_addr, (unsigned int) event.xfer_complete.len); + TU_LOG(USBD_DBG, "on EP %02X with %u bytes\r\n", ep_addr, (unsigned int) event.xfer_complete.len); _usbd_dev.ep_status[epnum][ep_dir].busy = false; _usbd_dev.ep_status[epnum][ep_dir].claimed = 0; @@ -545,7 +545,7 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) usbd_class_driver_t const * driver = get_driver( _usbd_dev.ep2drv[epnum][ep_dir] ); TU_ASSERT(driver, ); - TU_LOG2(" %s xfer callback\r\n", driver->name); + TU_LOG(USBD_DBG, " %s xfer callback\r\n", driver->name); driver->xfer_cb(event.rhport, ep_addr, (xfer_result_t)event.xfer_complete.result, event.xfer_complete.len); } } @@ -557,27 +557,27 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) // e.g suspend -> resume -> unplug/plug. Skip suspend/resume if not connected if ( _usbd_dev.connected ) { - TU_LOG2(": Remote Wakeup = %u\r\n", _usbd_dev.remote_wakeup_en); + TU_LOG(USBD_DBG, ": Remote Wakeup = %u\r\n", _usbd_dev.remote_wakeup_en); if (tud_suspend_cb) tud_suspend_cb(_usbd_dev.remote_wakeup_en); }else { - TU_LOG2(" Skipped\r\n"); + TU_LOG(USBD_DBG, " Skipped\r\n"); } break; case DCD_EVENT_RESUME: if ( _usbd_dev.connected ) { - TU_LOG2("\r\n"); + TU_LOG(USBD_DBG, "\r\n"); if (tud_resume_cb) tud_resume_cb(); }else { - TU_LOG2(" Skipped\r\n"); + TU_LOG(USBD_DBG, " Skipped\r\n"); } break; case USBD_EVENT_FUNC_CALL: - TU_LOG2("\r\n"); + TU_LOG(USBD_DBG, "\r\n"); if ( event.func_call.func ) event.func_call.func(event.func_call.param); break; @@ -602,7 +602,7 @@ void tud_task_ext(uint32_t timeout_ms, bool in_isr) static bool invoke_class_control(uint8_t rhport, usbd_class_driver_t const * driver, tusb_control_request_t const * request) { usbd_control_set_complete_callback(driver->control_xfer_cb); - TU_LOG2(" %s control request\r\n", driver->name); + TU_LOG(USBD_DBG, " %s control request\r\n", driver->name); return driver->control_xfer_cb(rhport, CONTROL_STAGE_SETUP, request); } @@ -626,8 +626,8 @@ static bool process_control_request(uint8_t rhport, tusb_control_request_t const #if CFG_TUSB_DEBUG >= 2 if (TUSB_REQ_TYPE_STANDARD == p_request->bmRequestType_bit.type && p_request->bRequest <= TUSB_REQ_SYNCH_FRAME) { - TU_LOG2(" %s", tu_str_std_request[p_request->bRequest]); - if (TUSB_REQ_GET_DESCRIPTOR != p_request->bRequest) TU_LOG2("\r\n"); + TU_LOG(USBD_DBG, " %s", tu_str_std_request[p_request->bRequest]); + if (TUSB_REQ_GET_DESCRIPTOR != p_request->bRequest) TU_LOG(USBD_DBG, "\r\n"); } #endif @@ -905,7 +905,7 @@ static bool process_set_config(uint8_t rhport, uint8_t cfg_num) if ( (sizeof(tusb_desc_interface_t) <= drv_len) && (drv_len <= remaining_len) ) { // Open successfully - TU_LOG2(" %s opened\r\n", driver->name); + TU_LOG(USBD_DBG, " %s opened\r\n", driver->name); // Some drivers use 2 or more interfaces but may not have IAD e.g MIDI (always) or // BTH (even CDC) with class in device descriptor (single interface) @@ -964,7 +964,7 @@ static bool process_get_descriptor(uint8_t rhport, tusb_control_request_t const { case TUSB_DESC_DEVICE: { - TU_LOG2(" Device\r\n"); + TU_LOG(USBD_DBG, " Device\r\n"); void* desc_device = (void*) (uintptr_t) tud_descriptor_device_cb(); @@ -988,7 +988,7 @@ static bool process_get_descriptor(uint8_t rhport, tusb_control_request_t const case TUSB_DESC_BOS: { - TU_LOG2(" BOS\r\n"); + TU_LOG(USBD_DBG, " BOS\r\n"); // requested by host if USB > 2.0 ( i.e 2.1 or 3.x ) if (!tud_descriptor_bos_cb) return false; @@ -1010,12 +1010,12 @@ static bool process_get_descriptor(uint8_t rhport, tusb_control_request_t const if ( desc_type == TUSB_DESC_CONFIGURATION ) { - TU_LOG2(" Configuration[%u]\r\n", desc_index); + TU_LOG(USBD_DBG, " Configuration[%u]\r\n", desc_index); desc_config = (uintptr_t) tud_descriptor_configuration_cb(desc_index); }else { // Host only request this after getting Device Qualifier descriptor - TU_LOG2(" Other Speed Configuration\r\n"); + TU_LOG(USBD_DBG, " Other Speed Configuration\r\n"); TU_VERIFY( tud_descriptor_other_speed_configuration_cb ); desc_config = (uintptr_t) tud_descriptor_other_speed_configuration_cb(desc_index); } @@ -1031,7 +1031,7 @@ static bool process_get_descriptor(uint8_t rhport, tusb_control_request_t const case TUSB_DESC_STRING: { - TU_LOG2(" String[%u]\r\n", desc_index); + TU_LOG(USBD_DBG, " String[%u]\r\n", desc_index); // String Descriptor always uses the desc set from user uint8_t const* desc_str = (uint8_t const*) tud_descriptor_string_cb(desc_index, tu_le16toh(p_request->wIndex)); @@ -1044,7 +1044,7 @@ static bool process_get_descriptor(uint8_t rhport, tusb_control_request_t const case TUSB_DESC_DEVICE_QUALIFIER: { - TU_LOG2(" Device Qualifier\r\n"); + TU_LOG(USBD_DBG, " Device Qualifier\r\n"); TU_VERIFY( tud_descriptor_device_qualifier_cb ); @@ -1237,7 +1237,7 @@ bool usbd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t // TODO skip ready() check for now since enumeration also use this API // TU_VERIFY(tud_ready()); - TU_LOG2(" Queue EP %02X with %u bytes ...\r\n", ep_addr, total_bytes); + TU_LOG(USBD_DBG, " Queue EP %02X with %u bytes ...\r\n", ep_addr, total_bytes); // Attempt to transfer on a busy endpoint, sound like an race condition ! TU_ASSERT(_usbd_dev.ep_status[epnum][dir].busy == 0); @@ -1254,7 +1254,7 @@ bool usbd_edpt_xfer(uint8_t rhport, uint8_t ep_addr, uint8_t * buffer, uint16_t // DCD error, mark endpoint as ready to allow next transfer _usbd_dev.ep_status[epnum][dir].busy = false; _usbd_dev.ep_status[epnum][dir].claimed = 0; - TU_LOG2("FAILED\r\n"); + TU_LOG(USBD_DBG, "FAILED\r\n"); TU_BREAKPOINT(); return false; } @@ -1271,7 +1271,7 @@ bool usbd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16 uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); - TU_LOG2(" Queue ISO EP %02X with %u bytes ... ", ep_addr, total_bytes); + TU_LOG(USBD_DBG, " Queue ISO EP %02X with %u bytes ... ", ep_addr, total_bytes); // Attempt to transfer on a busy endpoint, sound like an race condition ! TU_ASSERT(_usbd_dev.ep_status[epnum][dir].busy == 0); @@ -1282,14 +1282,14 @@ bool usbd_edpt_xfer_fifo(uint8_t rhport, uint8_t ep_addr, tu_fifo_t * ff, uint16 if (dcd_edpt_xfer_fifo(rhport, ep_addr, ff, total_bytes)) { - TU_LOG2("OK\r\n"); + TU_LOG(USBD_DBG, "OK\r\n"); return true; }else { // DCD error, mark endpoint as ready to allow next transfer _usbd_dev.ep_status[epnum][dir].busy = false; _usbd_dev.ep_status[epnum][dir].claimed = 0; - TU_LOG2("failed\r\n"); + TU_LOG(USBD_DBG, "failed\r\n"); TU_BREAKPOINT(); return false; } @@ -1360,7 +1360,7 @@ void usbd_edpt_close(uint8_t rhport, uint8_t ep_addr) rhport = _usbd_rhport; TU_ASSERT(dcd_edpt_close, /**/); - TU_LOG2(" CLOSING Endpoint: 0x%02X\r\n", ep_addr); + TU_LOG(USBD_DBG, " CLOSING Endpoint: 0x%02X\r\n", ep_addr); uint8_t const epnum = tu_edpt_number(ep_addr); uint8_t const dir = tu_edpt_dir(ep_addr); -- cgit v1.3.1 From 556b5d5044bd02e89d6b6c6f21e95d46f5fcdfc1 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 27 Jun 2022 12:22:36 +0700 Subject: change report len in hid API from uint8_t to uint16_t since HS interrupt endpoint can be up to 1024, 8-bit is not enough. affected APIs are: - tud_hid_n_report() / tud_hid_report() - tud_hid_report_complete_cb() --- examples/device/hid_boot_interface/src/main.c | 2 +- examples/device/hid_composite/src/main.c | 2 +- examples/device/hid_composite_freertos/src/main.c | 2 +- src/class/hid/hid_device.c | 8 ++++---- src/class/hid/hid_device.h | 8 ++++---- 5 files changed, 11 insertions(+), 11 deletions(-) (limited to 'src') diff --git a/examples/device/hid_boot_interface/src/main.c b/examples/device/hid_boot_interface/src/main.c index 21cdb383d..1958d614d 100644 --- a/examples/device/hid_boot_interface/src/main.c +++ b/examples/device/hid_boot_interface/src/main.c @@ -181,7 +181,7 @@ void tud_hid_set_protocol_cb(uint8_t instance, uint8_t protocol) // Invoked when sent REPORT successfully to host // Application can use this to send the next report // Note: For composite reports, report[0] is report ID -void tud_hid_report_complete_cb(uint8_t instance, uint8_t const* report, uint8_t len) +void tud_hid_report_complete_cb(uint8_t instance, uint8_t const* report, uint16_t len) { (void) instance; (void) report; diff --git a/examples/device/hid_composite/src/main.c b/examples/device/hid_composite/src/main.c index bc2347ab8..3c088b7c2 100644 --- a/examples/device/hid_composite/src/main.c +++ b/examples/device/hid_composite/src/main.c @@ -225,7 +225,7 @@ void hid_task(void) // Invoked when sent REPORT successfully to host // Application can use this to send the next report // Note: For composite reports, report[0] is report ID -void tud_hid_report_complete_cb(uint8_t instance, uint8_t const* report, uint8_t len) +void tud_hid_report_complete_cb(uint8_t instance, uint8_t const* report, uint16_t len) { (void) instance; (void) len; diff --git a/examples/device/hid_composite_freertos/src/main.c b/examples/device/hid_composite_freertos/src/main.c index 1030f3d05..ea8d917fe 100644 --- a/examples/device/hid_composite_freertos/src/main.c +++ b/examples/device/hid_composite_freertos/src/main.c @@ -294,7 +294,7 @@ void hid_task(void* param) // Invoked when sent REPORT successfully to host // Application can use this to send the next report // Note: For composite reports, report[0] is report ID -void tud_hid_report_complete_cb(uint8_t instance, uint8_t const* report, uint8_t len) +void tud_hid_report_complete_cb(uint8_t instance, uint8_t const* report, uint16_t len) { (void) instance; (void) len; diff --git a/src/class/hid/hid_device.c b/src/class/hid/hid_device.c index cdf155e1c..210050858 100644 --- a/src/class/hid/hid_device.c +++ b/src/class/hid/hid_device.c @@ -81,7 +81,7 @@ bool tud_hid_n_ready(uint8_t instance) return tud_ready() && (ep_in != 0) && !usbd_edpt_busy(rhport, ep_in); } -bool tud_hid_n_report(uint8_t instance, uint8_t report_id, void const* report, uint8_t len) +bool tud_hid_n_report(uint8_t instance, uint8_t report_id, void const* report, uint16_t len) { uint8_t const rhport = 0; hidd_interface_t * p_hid = &_hidd_itf[instance]; @@ -92,7 +92,7 @@ bool tud_hid_n_report(uint8_t instance, uint8_t report_id, void const* report, u // prepare data if (report_id) { - len = tu_min8(len, CFG_TUD_HID_EP_BUFSIZE-1); + len = tu_min16(len, CFG_TUD_HID_EP_BUFSIZE-1); p_hid->epin_buf[0] = report_id; memcpy(p_hid->epin_buf+1, report, len); @@ -100,7 +100,7 @@ bool tud_hid_n_report(uint8_t instance, uint8_t report_id, void const* report, u }else { // If report id = 0, skip ID field - len = tu_min8(len, CFG_TUD_HID_EP_BUFSIZE); + len = tu_min16(len, CFG_TUD_HID_EP_BUFSIZE); memcpy(p_hid->epin_buf, report, len); } @@ -402,7 +402,7 @@ bool hidd_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t result, uint32_ { if (tud_hid_report_complete_cb) { - tud_hid_report_complete_cb(instance, p_hid->epin_buf, (uint8_t) xferred_bytes); + tud_hid_report_complete_cb(instance, p_hid->epin_buf, (uint16_t) xferred_bytes); } } // Received report diff --git a/src/class/hid/hid_device.h b/src/class/hid/hid_device.h index 078b67349..3714d2769 100644 --- a/src/class/hid/hid_device.h +++ b/src/class/hid/hid_device.h @@ -62,7 +62,7 @@ uint8_t tud_hid_n_interface_protocol(uint8_t instance); uint8_t tud_hid_n_get_protocol(uint8_t instance); // Send report to host -bool tud_hid_n_report(uint8_t instance, uint8_t report_id, void const* report, uint8_t len); +bool tud_hid_n_report(uint8_t instance, uint8_t report_id, void const* report, uint16_t len); // KEYBOARD: convenient helper to send keyboard report if application // use template layout report as defined by hid_keyboard_report_t @@ -82,7 +82,7 @@ bool tud_hid_n_gamepad_report(uint8_t instance, uint8_t report_id, int8_t x, int static inline bool tud_hid_ready(void); static inline uint8_t tud_hid_interface_protocol(void); static inline uint8_t tud_hid_get_protocol(void); -static inline bool tud_hid_report(uint8_t report_id, void const* report, uint8_t len); +static inline bool tud_hid_report(uint8_t report_id, void const* report, uint16_t len); static inline bool tud_hid_keyboard_report(uint8_t report_id, uint8_t modifier, uint8_t keycode[6]); static inline bool tud_hid_mouse_report(uint8_t report_id, uint8_t buttons, int8_t x, int8_t y, int8_t vertical, int8_t horizontal); static inline bool tud_hid_gamepad_report(uint8_t report_id, int8_t x, int8_t y, int8_t z, int8_t rz, int8_t rx, int8_t ry, uint8_t hat, uint32_t buttons); @@ -116,7 +116,7 @@ TU_ATTR_WEAK bool tud_hid_set_idle_cb(uint8_t instance, uint8_t idle_rate); // Invoked when sent REPORT successfully to host // Application can use this to send the next report // Note: For composite reports, report[0] is report ID -TU_ATTR_WEAK void tud_hid_report_complete_cb(uint8_t instance, uint8_t const* report, uint8_t len); +TU_ATTR_WEAK void tud_hid_report_complete_cb(uint8_t instance, uint8_t const* report, uint16_t len); //--------------------------------------------------------------------+ @@ -137,7 +137,7 @@ static inline uint8_t tud_hid_get_protocol(void) return tud_hid_n_get_protocol(0); } -static inline bool tud_hid_report(uint8_t report_id, void const* report, uint8_t len) +static inline bool tud_hid_report(uint8_t report_id, void const* report, uint16_t len) { return tud_hid_n_report(0, report_id, report, len); } -- cgit v1.3.1 From 6522a8150e22d47bacabd2f1f027452db2254984 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 27 Jun 2022 13:48:47 +0700 Subject: fix all device examples warnings --- examples/device/midi_test/src/main.c | 2 +- examples/device/msc_dual_lun/src/msc_disk_dual.c | 6 ++-- examples/device/uac2_headset/src/main.c | 16 ++++----- examples/device/uac2_headset/src/usb_descriptors.c | 2 +- src/class/audio/audio_device.c | 12 +++++-- src/class/vendor/vendor_device.c | 10 +++--- src/class/video/video_device.c | 38 ++++++++++++---------- 7 files changed, 47 insertions(+), 39 deletions(-) (limited to 'src') diff --git a/examples/device/midi_test/src/main.c b/examples/device/midi_test/src/main.c index b47d1af76..3310348bd 100644 --- a/examples/device/midi_test/src/main.c +++ b/examples/device/midi_test/src/main.c @@ -140,7 +140,7 @@ void midi_task(void) start_ms += 286; // Previous positions in the note sequence. - int previous = note_pos - 1; + int previous = (int) (note_pos - 1); // If we currently are at position 0, set the // previous position to the last note in the sequence. diff --git a/examples/device/msc_dual_lun/src/msc_disk_dual.c b/examples/device/msc_dual_lun/src/msc_disk_dual.c index 37446ebc3..2b773b43b 100644 --- a/examples/device/msc_dual_lun/src/msc_disk_dual.c +++ b/examples/device/msc_dual_lun/src/msc_disk_dual.c @@ -277,7 +277,7 @@ int32_t tud_msc_read10_cb(uint8_t lun, uint32_t lba, uint32_t offset, void* buff uint8_t const* addr = (lun ? msc_disk1[lba] : msc_disk0[lba]) + offset; memcpy(buffer, addr, bufsize); - return bufsize; + return (int32_t) bufsize; } bool tud_msc_is_writable_cb (uint8_t lun) @@ -305,7 +305,7 @@ int32_t tud_msc_write10_cb(uint8_t lun, uint32_t lba, uint32_t offset, uint8_t* (void) lun; (void) lba; (void) offset; (void) buffer; #endif - return bufsize; + return (int32_t) bufsize; } // Callback invoked when received an SCSI command not in built-in list below @@ -339,7 +339,7 @@ int32_t tud_msc_scsi_cb (uint8_t lun, uint8_t const scsi_cmd[16], void* buffer, { if(in_xfer) { - memcpy(buffer, response, resplen); + memcpy(buffer, response, (size_t) resplen); }else { // SCSI output diff --git a/examples/device/uac2_headset/src/main.c b/examples/device/uac2_headset/src/main.c index a8d204eaa..003dc2a74 100644 --- a/examples/device/uac2_headset/src/main.c +++ b/examples/device/uac2_headset/src/main.c @@ -159,7 +159,7 @@ static bool tud_audio_clock_get_request(uint8_t rhport, audio_control_request_t { TU_LOG1("Clock get current freq %lu\r\n", current_sample_rate); - audio_control_cur_4_t curf = { tu_htole32(current_sample_rate) }; + audio_control_cur_4_t curf = { (int32_t) tu_htole32(current_sample_rate) }; return tud_audio_buffer_and_schedule_control_xfer(rhport, (tusb_control_request_t const *)request, &curf, sizeof(curf)); } else if (request->bRequest == AUDIO_CS_REQ_RANGE) @@ -171,8 +171,8 @@ static bool tud_audio_clock_get_request(uint8_t rhport, audio_control_request_t TU_LOG1("Clock get %d freq ranges\r\n", N_SAMPLE_RATES); for(uint8_t i = 0; i < N_SAMPLE_RATES; i++) { - rangef.subrange[i].bMin = sample_rates[i]; - rangef.subrange[i].bMax = sample_rates[i]; + rangef.subrange[i].bMin = (int32_t) sample_rates[i]; + rangef.subrange[i].bMax = (int32_t) sample_rates[i]; rangef.subrange[i].bRes = 0; TU_LOG1("Range %d (%d, %d, %d)\r\n", i, (int)rangef.subrange[i].bMin, (int)rangef.subrange[i].bMax, (int)rangef.subrange[i].bRes); } @@ -204,7 +204,7 @@ static bool tud_audio_clock_set_request(uint8_t rhport, audio_control_request_t { TU_VERIFY(request->wLength == sizeof(audio_control_cur_4_t)); - current_sample_rate = ((audio_control_cur_4_t const *)buf)->bCur; + current_sample_rate = (uint32_t) ((audio_control_cur_4_t const *)buf)->bCur; TU_LOG1("Clock set current freq: %ld\r\n", current_sample_rate); @@ -403,9 +403,9 @@ void audio_task(void) // Combine two channels into one int32_t left = *src++; int32_t right = *src++; - *dst++ = (left >> 1) + (right >> 1); + *dst++ = (int16_t) ((left >> 1) + (right >> 1)); } - tud_audio_write((uint8_t *)mic_buf, spk_data_size / 2); + tud_audio_write((uint8_t *)mic_buf, (uint16_t) (spk_data_size / 2)); spk_data_size = 0; } else if (current_resolution == 24) @@ -418,9 +418,9 @@ void audio_task(void) // Combine two channels into one int32_t left = *src++; int32_t right = *src++; - *dst++ = ((left >> 1) + (right >> 1)) & 0xffffff00; + *dst++ = (int32_t) ((uint32_t) ((left >> 1) + (right >> 1)) & 0xffffff00ul); } - tud_audio_write((uint8_t *)mic_buf, spk_data_size / 2); + tud_audio_write((uint8_t *)mic_buf, (uint16_t) (spk_data_size / 2)); spk_data_size = 0; } } diff --git a/examples/device/uac2_headset/src/usb_descriptors.c b/examples/device/uac2_headset/src/usb_descriptors.c index a2d6368bf..10f5cbd27 100644 --- a/examples/device/uac2_headset/src/usb_descriptors.c +++ b/examples/device/uac2_headset/src/usb_descriptors.c @@ -165,7 +165,7 @@ uint16_t const* tud_descriptor_string_cb(uint8_t index, uint16_t langid) } // first byte is length (including header), second byte is string type - _desc_str[0] = (TUSB_DESC_STRING << 8 ) | (2 * chr_count + 2); + _desc_str[0] = (uint16_t) ((TUSB_DESC_STRING << 8 ) | (2*chr_count + 2)); return _desc_str; } diff --git a/src/class/audio/audio_device.c b/src/class/audio/audio_device.c index e13e4a46c..6df68c559 100644 --- a/src/class/audio/audio_device.c +++ b/src/class/audio/audio_device.c @@ -537,7 +537,7 @@ tu_fifo_t* tud_audio_n_get_rx_support_ff(uint8_t func_id, uint8_t ff_idx) static bool audiod_rx_done_cb(uint8_t rhport, audiod_function_t* audio, uint16_t n_bytes_received) { - uint8_t idxItf; + uint8_t idxItf = 0; uint8_t const *dummy2; uint8_t idx_audio_fct = 0; @@ -548,7 +548,10 @@ static bool audiod_rx_done_cb(uint8_t rhport, audiod_function_t* audio, uint16_t } // Call a weak callback here - a possibility for user to get informed an audio packet was received and data gets now loaded into EP FIFO (or decoded into support RX software FIFO) - if (tud_audio_rx_done_pre_read_cb) TU_VERIFY(tud_audio_rx_done_pre_read_cb(rhport, n_bytes_received, idx_audio_fct, audio->ep_out, audio->alt_setting[idxItf])); + if (tud_audio_rx_done_pre_read_cb) + { + TU_VERIFY(tud_audio_rx_done_pre_read_cb(rhport, n_bytes_received, idx_audio_fct, audio->ep_out, audio->alt_setting[idxItf])); + } #if CFG_TUD_AUDIO_ENABLE_DECODING && CFG_TUD_AUDIO_ENABLE_EP_OUT @@ -602,7 +605,10 @@ static bool audiod_rx_done_cb(uint8_t rhport, audiod_function_t* audio, uint16_t #endif // Call a weak callback here - a possibility for user to get informed decoding was completed - if (tud_audio_rx_done_post_read_cb) TU_VERIFY(tud_audio_rx_done_post_read_cb(rhport, n_bytes_received, idx_audio_fct, audio->ep_out, audio->alt_setting[idxItf])); + if (tud_audio_rx_done_post_read_cb) + { + TU_VERIFY(tud_audio_rx_done_post_read_cb(rhport, n_bytes_received, idx_audio_fct, audio->ep_out, audio->alt_setting[idxItf])); + } return true; } diff --git a/src/class/vendor/vendor_device.c b/src/class/vendor/vendor_device.c index c7dfa0062..3b81a108f 100644 --- a/src/class/vendor/vendor_device.c +++ b/src/class/vendor/vendor_device.c @@ -100,7 +100,7 @@ static void _prep_out_transaction (vendord_interface_t* p_itf) uint32_t tud_vendor_n_read (uint8_t itf, void* buffer, uint32_t bufsize) { vendord_interface_t* p_itf = &_vendord_itf[itf]; - uint32_t num_read = tu_fifo_read_n(&p_itf->rx_ff, buffer, bufsize); + uint32_t num_read = tu_fifo_read_n(&p_itf->rx_ff, buffer, (uint16_t) bufsize); _prep_out_transaction(p_itf); return num_read; } @@ -133,7 +133,7 @@ static uint16_t maybe_transmit(vendord_interface_t* p_itf) uint32_t tud_vendor_n_write (uint8_t itf, void const* buffer, uint32_t bufsize) { vendord_interface_t* p_itf = &_vendord_itf[itf]; - uint16_t ret = tu_fifo_write_n(&p_itf->tx_ff, buffer, bufsize); + uint16_t ret = tu_fifo_write_n(&p_itf->tx_ff, buffer, (uint16_t) bufsize); if (tu_fifo_count(&p_itf->tx_ff) >= CFG_TUD_VENDOR_EPSIZE) { maybe_transmit(p_itf); } @@ -231,7 +231,7 @@ uint16_t vendord_open(uint8_t rhport, tusb_desc_interface_t const * desc_itf, ui if ( p_vendor->ep_in ) maybe_transmit(p_vendor); } - return (uintptr_t) p_desc - (uintptr_t) desc_itf; + return (uint16_t) ((uintptr_t) p_desc - (uintptr_t) desc_itf); } bool vendord_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t result, uint32_t xferred_bytes) @@ -252,7 +252,7 @@ bool vendord_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t result, uint if ( ep_addr == p_itf->ep_out ) { // Receive new data - tu_fifo_write_n(&p_itf->rx_ff, p_itf->epout_buf, xferred_bytes); + tu_fifo_write_n(&p_itf->rx_ff, p_itf->epout_buf, (uint16_t) xferred_bytes); // Invoked callback if any if (tud_vendor_rx_cb) tud_vendor_rx_cb(itf); @@ -261,7 +261,7 @@ bool vendord_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t result, uint } else if ( ep_addr == p_itf->ep_in ) { - if (tud_vendor_tx_cb) tud_vendor_tx_cb(itf, xferred_bytes); + if (tud_vendor_tx_cb) tud_vendor_tx_cb(itf, (uint16_t) xferred_bytes); // Send complete, try to send more if possible maybe_transmit(p_itf); } diff --git a/src/class/video/video_device.c b/src/class/video/video_device.c index 91718f205..7636db5fe 100644 --- a/src/class/video/video_device.c +++ b/src/class/video/video_device.c @@ -297,7 +297,7 @@ static bool _update_streaming_parameters(videod_streaming_interface_t const *stm { tusb_desc_vs_itf_t const *vs = _get_desc_vs(stm); uint_fast8_t fmtnum = param->bFormatIndex; - TU_ASSERT(fmtnum <= vs->stm.bNumFormats); + TU_ASSERT(vs && fmtnum <= vs->stm.bNumFormats); if (!fmtnum) { if (1 < vs->stm.bNumFormats) return true; /* Need to negotiate all variables. */ fmtnum = 1; @@ -393,6 +393,7 @@ static bool _negotiate_streaming_parameters(videod_streaming_interface_t const * uint_fast8_t frmnum = param->bFrameIndex; if (!frmnum) { tusb_desc_vs_itf_t const *vs = _get_desc_vs(stm); + TU_ASSERT(vs); void const *end = _end_of_streaming_descriptor(vs); tusb_desc_cs_video_fmt_uncompressed_t const *fmt = _find_desc_format(tu_desc_next(vs), end, fmtnum); switch (request) { @@ -407,15 +408,16 @@ static bool _negotiate_streaming_parameters(videod_streaming_interface_t const * break; default: return false; } - param->bFrameIndex = frmnum; + param->bFrameIndex = (uint8_t) frmnum; /* Set the parameters determined by the frame */ tusb_desc_cs_video_frm_uncompressed_t const *frm = _find_desc_frame(tu_desc_next(fmt), end, frmnum); - param->dwMaxVideoFrameSize = frm->wWidth * frm->wHeight * fmt->bBitsPerPixel / 8; + param->dwMaxVideoFrameSize = (uint32_t) (frm->wWidth * frm->wHeight * fmt->bBitsPerPixel / 8); return true; } if (!param->dwFrameInterval) { tusb_desc_vs_itf_t const *vs = _get_desc_vs(stm); + TU_ASSERT(vs); void const *end = _end_of_streaming_descriptor(vs); tusb_desc_cs_video_fmt_uncompressed_t const *fmt = _find_desc_format(tu_desc_next(vs), end, fmtnum); tusb_desc_cs_video_frm_uncompressed_t const *frm = _find_desc_frame(tu_desc_next(fmt), end, frmnum); @@ -532,7 +534,7 @@ static bool _open_vc_itf(uint8_t rhport, videod_interface_t *self, uint_fast8_t /* Open the notification endpoint */ TU_ASSERT(usbd_edpt_open(rhport, notif)); } - self->cur = (void const*)vc - beg; + self->cur = (uint16_t) ((void const*)vc - beg); return true; } @@ -550,7 +552,7 @@ static bool _open_vs_itf(uint8_t rhport, videod_streaming_interface_t *stm, uint for (i = 0; i < TU_ARRAY_SIZE(stm->desc.ep); ++i) { uint_fast16_t ofs_ep = stm->desc.ep[i]; if (!ofs_ep) break; - uint_fast8_t ep_adr = _desc_ep_addr(desc + ofs_ep); + uint8_t ep_adr = _desc_ep_addr(desc + ofs_ep); usbd_edpt_close(rhport, ep_adr); stm->desc.ep[i] = 0; TU_LOG2(" close EP%02x\n", ep_adr); @@ -567,7 +569,7 @@ static bool _open_vs_itf(uint8_t rhport, videod_streaming_interface_t *stm, uint TU_VERIFY(cur < end); uint_fast8_t numeps = ((tusb_desc_interface_t const *)cur)->bNumEndpoints; TU_ASSERT(numeps <= TU_ARRAY_SIZE(stm->desc.ep)); - stm->desc.cur = cur - desc; /* Save the offset of the new settings */ + stm->desc.cur = (uint16_t) (cur - desc); /* Save the offset of the new settings */ if (!altnum) { /* initialize streaming settings */ stm->max_payload_transfer_size = 0; @@ -594,7 +596,7 @@ static bool _open_vs_itf(uint8_t rhport, videod_streaming_interface_t *stm, uint stm->max_payload_transfer_size = max_size; } TU_ASSERT(usbd_edpt_open(rhport, ep)); - stm->desc.ep[i] = cur - desc; + stm->desc.ep[i] = (uint16_t) (cur - desc); TU_LOG2(" open EP%02x\n", _desc_ep_addr(cur)); } /* initialize payload header */ @@ -976,7 +978,7 @@ bool tud_video_n_frame_xfer(uint_fast8_t ctl_idx, uint_fast8_t stm_idx, void *bu /* Find EP address */ void const *desc = _videod_itf[stm->index_vc].beg; - uint_fast8_t ep_addr = 0; + uint8_t ep_addr = 0; for (uint_fast8_t i = 0; i < CFG_TUD_VIDEO_STREAMING; ++i) { uint_fast16_t ofs_ep = stm->desc.ep[i]; if (!ofs_ep) continue; @@ -985,7 +987,7 @@ bool tud_video_n_frame_xfer(uint_fast8_t ctl_idx, uint_fast8_t stm_idx, void *bu } if (!ep_addr) return false; - TU_VERIFY( usbd_edpt_claim(0, ep_addr)); + TU_VERIFY( usbd_edpt_claim(0, ep_addr) ); /* update the packet header */ tusb_video_payload_header_t *hdr = (tusb_video_payload_header_t*)stm->ep_buf; hdr->FrameID ^= 1; @@ -994,7 +996,7 @@ bool tud_video_n_frame_xfer(uint_fast8_t ctl_idx, uint_fast8_t stm_idx, void *bu stm->buffer = (uint8_t*)buffer; stm->bufsize = bufsize; uint_fast16_t pkt_len = _prepare_in_payload(stm); - TU_ASSERT( usbd_edpt_xfer(0, ep_addr, stm->ep_buf, pkt_len), 0); + TU_ASSERT( usbd_edpt_xfer(0, ep_addr, stm->ep_buf, (uint16_t) pkt_len), 0); return true; } @@ -1034,7 +1036,7 @@ uint16_t videod_open(uint8_t rhport, tusb_desc_interface_t const * itf_desc, uin /* Find available interface */ videod_interface_t *self = NULL; - uint_fast8_t ctl_idx; + uint8_t ctl_idx; for (ctl_idx = 0; ctl_idx < CFG_TUD_VIDEO; ++ctl_idx) { if (_videod_itf[ctl_idx].beg) continue; self = &_videod_itf[ctl_idx]; @@ -1051,10 +1053,10 @@ uint16_t videod_open(uint8_t rhport, tusb_desc_interface_t const * itf_desc, uin uint_fast8_t bInCollection = vc->ctl.bInCollection; /* Find the end of the video interface descriptor */ void const *cur = _next_desc_itf(itf_desc, end); - for (uint_fast8_t stm_idx = 0; stm_idx < bInCollection; ++stm_idx) { + for (uint8_t stm_idx = 0; stm_idx < bInCollection; ++stm_idx) { videod_streaming_interface_t *stm = NULL; /* find free streaming interface handle */ - for (uint_fast8_t i = 0; i < CFG_TUD_VIDEO_STREAMING; ++i) { + for (uint8_t i = 0; i < CFG_TUD_VIDEO_STREAMING; ++i) { if (_videod_streaming_itf[i].desc.beg) continue; stm = &_videod_streaming_itf[i]; self->stm[stm_idx] = i; @@ -1063,12 +1065,12 @@ uint16_t videod_open(uint8_t rhport, tusb_desc_interface_t const * itf_desc, uin TU_ASSERT(stm, 0); stm->index_vc = ctl_idx; stm->index_vs = stm_idx; - stm->desc.beg = (uintptr_t)cur - (uintptr_t)itf_desc; + stm->desc.beg = (uint16_t) ((uintptr_t)cur - (uintptr_t)itf_desc); cur = _next_desc_itf(cur, end); - stm->desc.end = (uintptr_t)cur - (uintptr_t)itf_desc; + stm->desc.end = (uint16_t) ((uintptr_t)cur - (uintptr_t)itf_desc); } - self->len = (uintptr_t)cur - (uintptr_t)itf_desc; - return (uintptr_t)cur - (uintptr_t)itf_desc; + self->len = (uint16_t) ((uintptr_t)cur - (uintptr_t)itf_desc); + return (uint16_t) ((uintptr_t)cur - (uintptr_t)itf_desc); } // Invoked when a control transfer occurred on an interface of this class @@ -1134,7 +1136,7 @@ bool videod_xfer_cb(uint8_t rhport, uint8_t ep_addr, xfer_result_t result, uint3 /* Claim the endpoint */ TU_VERIFY( usbd_edpt_claim(rhport, ep_addr), 0); uint_fast16_t pkt_len = _prepare_in_payload(stm); - TU_ASSERT( usbd_edpt_xfer(rhport, ep_addr, stm->ep_buf, pkt_len), 0); + TU_ASSERT( usbd_edpt_xfer(rhport, ep_addr, stm->ep_buf, (uint16_t) pkt_len), 0); } else { stm->buffer = NULL; stm->bufsize = 0; -- cgit v1.3.1 From a0ef4898906a5985deae11e5539a942885398ca1 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 27 Jun 2022 17:11:24 +0700 Subject: fix all warnings with host rp2040 --- .../dual/host_hid_to_device_cdc/CMakeLists.txt | 4 + examples/dual/host_hid_to_device_cdc/src/main.c | 6 +- examples/host/bare_api/CMakeLists.txt | 3 + examples/host/bare_api/src/main.c | 11 +- examples/host/cdc_msc_hid/CMakeLists.txt | 3 + examples/host/hid_controller/CMakeLists.txt | 3 + src/class/cdc/cdc_host.c | 8 +- src/class/hid/hid_host.c | 7 +- src/class/msc/msc_host.c | 8 +- src/host/usbh.c | 6 +- src/osal/osal_pico.h | 5 - src/portable/raspberrypi/rp2040/hcd_rp2040.c | 111 +++++++++++---------- 12 files changed, 98 insertions(+), 77 deletions(-) (limited to 'src') diff --git a/examples/dual/host_hid_to_device_cdc/CMakeLists.txt b/examples/dual/host_hid_to_device_cdc/CMakeLists.txt index ea4e087e3..cd6f16339 100644 --- a/examples/dual/host_hid_to_device_cdc/CMakeLists.txt +++ b/examples/dual/host_hid_to_device_cdc/CMakeLists.txt @@ -23,6 +23,10 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +# skip extra warnings since pio-usb still has some warnings to fix +#include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_dual_usb_example(${PROJECT}) diff --git a/examples/dual/host_hid_to_device_cdc/src/main.c b/examples/dual/host_hid_to_device_cdc/src/main.c index 6a25a28da..bd7870274 100644 --- a/examples/dual/host_hid_to_device_cdc/src/main.c +++ b/examples/dual/host_hid_to_device_cdc/src/main.c @@ -160,7 +160,7 @@ void tuh_hid_mount_cb(uint8_t dev_addr, uint8_t instance, uint8_t const* desc_re char tempbuf[256]; int count = sprintf(tempbuf, "[%04x:%04x][%u] HID Interface%u, Protocol = %s\r\n", vid, pid, dev_addr, instance, protocol_str[itf_protocol]); - tud_cdc_write(tempbuf, count); + tud_cdc_write(tempbuf, (uint32_t) count); tud_cdc_write_flush(); // Receive report from boot keyboard & mouse only @@ -179,7 +179,7 @@ void tuh_hid_umount_cb(uint8_t dev_addr, uint8_t instance) { char tempbuf[256]; int count = sprintf(tempbuf, "[%u] HID Interface%u is unmounted\r\n", dev_addr, instance); - tud_cdc_write(tempbuf, count); + tud_cdc_write(tempbuf, (uint32_t) count); tud_cdc_write_flush(); } @@ -251,7 +251,7 @@ static void process_mouse_report(uint8_t dev_addr, hid_mouse_report_t const * re char tempbuf[32]; int count = sprintf(tempbuf, "[%u] %c%c%c %d %d %d\r\n", dev_addr, l, m, r, report->x, report->y, report->wheel); - tud_cdc_write(tempbuf, count); + tud_cdc_write(tempbuf, (uint32_t) count); tud_cdc_write_flush(); } diff --git a/examples/host/bare_api/CMakeLists.txt b/examples/host/bare_api/CMakeLists.txt index bc04b01a7..98540ffb0 100644 --- a/examples/host/bare_api/CMakeLists.txt +++ b/examples/host/bare_api/CMakeLists.txt @@ -22,6 +22,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_host_example(${PROJECT}) diff --git a/examples/host/bare_api/src/main.c b/examples/host/bare_api/src/main.c index 9ccd856d4..51cab2de0 100644 --- a/examples/host/bare_api/src/main.c +++ b/examples/host/bare_api/src/main.c @@ -189,7 +189,7 @@ void parse_config_descriptor(uint8_t dev_addr, tusb_desc_configuration_t const* if( TUSB_DESC_INTERFACE != tu_desc_type(p_desc) ) return; tusb_desc_interface_t const* desc_itf = (tusb_desc_interface_t const*) p_desc; - uint16_t const drv_len = count_interface_total_len(desc_itf, assoc_itf_count, desc_end-p_desc); + uint16_t const drv_len = count_interface_total_len(desc_itf, assoc_itf_count, (uint16_t) (desc_end-p_desc)); // probably corrupted descriptor if(drv_len < sizeof(tusb_desc_interface_t)) return; @@ -244,7 +244,8 @@ void hid_report_received(tuh_xfer_t* xfer); void open_hid_interface(uint8_t daddr, tusb_desc_interface_t const *desc_itf, uint16_t max_len) { // len = interface + hid + n*endpoints - uint16_t const drv_len = sizeof(tusb_desc_interface_t) + sizeof(tusb_hid_descriptor_hid_t) + desc_itf->bNumEndpoints*sizeof(tusb_desc_endpoint_t); + uint16_t const drv_len = (uint16_t) (sizeof(tusb_desc_interface_t) + sizeof(tusb_hid_descriptor_hid_t) + + desc_itf->bNumEndpoints * sizeof(tusb_desc_endpoint_t)); // corrupted descriptor if (max_len < drv_len) return; @@ -377,7 +378,7 @@ static void _convert_utf16le_to_utf8(const uint16_t *utf16, size_t utf16_len, ui for (size_t i = 0; i < utf16_len; i++) { uint16_t chr = utf16[i]; if (chr < 0x80) { - *utf8++ = chr & 0xff; + *utf8++ = chr & 0xffu; } else if (chr < 0x800) { *utf8++ = (uint8_t)(0xC0 | (chr >> 6 & 0x1F)); *utf8++ = (uint8_t)(0x80 | (chr >> 0 & 0x3F)); @@ -405,12 +406,12 @@ static int _count_utf8_bytes(const uint16_t *buf, size_t len) { } // TODO: Handle UTF-16 code points that take two entries. } - return total_bytes; + return (int) total_bytes; } static void print_utf16(uint16_t *temp_buf, size_t buf_len) { size_t utf16_len = ((temp_buf[0] & 0xff) - 2) / sizeof(uint16_t); - size_t utf8_len = _count_utf8_bytes(temp_buf + 1, utf16_len); + size_t utf8_len = (size_t) _count_utf8_bytes(temp_buf + 1, utf16_len); _convert_utf16le_to_utf8(temp_buf + 1, utf16_len, (uint8_t *) temp_buf, sizeof(uint16_t) * buf_len); ((uint8_t*) temp_buf)[utf8_len] = '\0'; diff --git a/examples/host/cdc_msc_hid/CMakeLists.txt b/examples/host/cdc_msc_hid/CMakeLists.txt index c4a4d8e63..6990e957b 100644 --- a/examples/host/cdc_msc_hid/CMakeLists.txt +++ b/examples/host/cdc_msc_hid/CMakeLists.txt @@ -24,6 +24,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_host_example(${PROJECT}) diff --git a/examples/host/hid_controller/CMakeLists.txt b/examples/host/hid_controller/CMakeLists.txt index 6153d399a..eefeb4a49 100644 --- a/examples/host/hid_controller/CMakeLists.txt +++ b/examples/host/hid_controller/CMakeLists.txt @@ -23,6 +23,9 @@ target_include_directories(${PROJECT} PUBLIC ${CMAKE_CURRENT_SOURCE_DIR}/src ) +# Example common such as compiler warnings +include(${CMAKE_CURRENT_SOURCE_DIR}/../../example.cmake) + # Configure compilation flags and libraries for the example... see the corresponding function # in hw/bsp/FAMILY/family.cmake for details. family_configure_host_example(${PROJECT}) diff --git a/src/class/cdc/cdc_host.c b/src/class/cdc/cdc_host.c index 044085e81..ee824cb4e 100644 --- a/src/class/cdc/cdc_host.c +++ b/src/class/cdc/cdc_host.c @@ -105,7 +105,7 @@ bool tuh_cdc_send(uint8_t dev_addr, void const * p_data, uint32_t length, bool i uint8_t const ep_out = cdch_data[dev_addr-1].ep_out; if ( usbh_edpt_busy(dev_addr, ep_out) ) return false; - return usbh_edpt_xfer(dev_addr, ep_out, (void*)(uintptr_t) p_data, length); + return usbh_edpt_xfer(dev_addr, ep_out, (void*)(uintptr_t) p_data, (uint16_t) length); } bool tuh_cdc_receive(uint8_t dev_addr, void * p_buffer, uint32_t length, bool is_notify) @@ -117,7 +117,7 @@ bool tuh_cdc_receive(uint8_t dev_addr, void * p_buffer, uint32_t length, bool is uint8_t const ep_in = cdch_data[dev_addr-1].ep_in; if ( usbh_edpt_busy(dev_addr, ep_in) ) return false; - return usbh_edpt_xfer(dev_addr, ep_in, p_buffer, length); + return usbh_edpt_xfer(dev_addr, ep_in, p_buffer, (uint16_t) length); } bool tuh_cdc_set_control_line_state(uint8_t dev_addr, bool dtr, bool rts, tuh_xfer_cb_t complete_cb) @@ -133,8 +133,8 @@ bool tuh_cdc_set_control_line_state(uint8_t dev_addr, bool dtr, bool rts, tuh_xf .direction = TUSB_DIR_OUT }, .bRequest = CDC_REQUEST_SET_CONTROL_LINE_STATE, - .wValue = (rts ? 2 : 0) | (dtr ? 1 : 0), - .wIndex = p_cdc->itf_num, + .wValue = tu_htole16((uint16_t) ((dtr ? 1u : 0u) | (rts ? 2u : 0u))), + .wIndex = tu_htole16(p_cdc->itf_num), .wLength = 0 }; diff --git a/src/class/hid/hid_host.c b/src/class/hid/hid_host.c index 2573f5a6b..ca745464c 100644 --- a/src/class/hid/hid_host.c +++ b/src/class/hid/hid_host.c @@ -295,10 +295,10 @@ bool hidh_xfer_cb(uint8_t dev_addr, uint8_t ep_addr, xfer_result_t result, uint3 { TU_LOG2(" Get Report callback (%u, %u)\r\n", dev_addr, instance); TU_LOG3_MEM(hid_itf->epin_buf, xferred_bytes, 2); - tuh_hid_report_received_cb(dev_addr, instance, hid_itf->epin_buf, xferred_bytes); + tuh_hid_report_received_cb(dev_addr, instance, hid_itf->epin_buf, (uint16_t) xferred_bytes); }else { - if (tuh_hid_report_sent_cb) tuh_hid_report_sent_cb(dev_addr, instance, hid_itf->epout_buf, xferred_bytes); + if (tuh_hid_report_sent_cb) tuh_hid_report_sent_cb(dev_addr, instance, hid_itf->epout_buf, (uint16_t) xferred_bytes); } return true; @@ -332,7 +332,8 @@ bool hidh_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_interface_t const *de TU_LOG2("[%u] HID opening Interface %u\r\n", dev_addr, desc_itf->bInterfaceNumber); // len = interface + hid + n*endpoints - uint16_t const drv_len = sizeof(tusb_desc_interface_t) + sizeof(tusb_hid_descriptor_hid_t) + desc_itf->bNumEndpoints*sizeof(tusb_desc_endpoint_t); + uint16_t const drv_len = (uint16_t) (sizeof(tusb_desc_interface_t) + sizeof(tusb_hid_descriptor_hid_t) + + desc_itf->bNumEndpoints * sizeof(tusb_desc_endpoint_t)); TU_ASSERT(max_len >= drv_len); uint8_t const *p_desc = (uint8_t const *) desc_itf; diff --git a/src/class/msc/msc_host.c b/src/class/msc/msc_host.c index c54a63f37..934f79ff7 100644 --- a/src/class/msc/msc_host.c +++ b/src/class/msc/msc_host.c @@ -325,19 +325,19 @@ bool msch_xfer_cb(uint8_t dev_addr, uint8_t ep_addr, xfer_result_t event, uint32 p_msc->stage = MSC_STAGE_DATA; uint8_t const ep_data = (cbw->dir & TUSB_DIR_IN_MASK) ? p_msc->ep_in : p_msc->ep_out; - TU_ASSERT(usbh_edpt_xfer(dev_addr, ep_data, p_msc->buffer, cbw->total_bytes)); + TU_ASSERT(usbh_edpt_xfer(dev_addr, ep_data, p_msc->buffer, (uint16_t) cbw->total_bytes)); }else { // Status stage p_msc->stage = MSC_STAGE_STATUS; - TU_ASSERT(usbh_edpt_xfer(dev_addr, p_msc->ep_in, (uint8_t*) &p_msc->csw, sizeof(msc_csw_t))); + TU_ASSERT(usbh_edpt_xfer(dev_addr, p_msc->ep_in, (uint8_t*) &p_msc->csw, (uint16_t) sizeof(msc_csw_t))); } break; case MSC_STAGE_DATA: // Status stage p_msc->stage = MSC_STAGE_STATUS; - TU_ASSERT(usbh_edpt_xfer(dev_addr, p_msc->ep_in, (uint8_t*) &p_msc->csw, sizeof(msc_csw_t))); + TU_ASSERT(usbh_edpt_xfer(dev_addr, p_msc->ep_in, (uint8_t*) &p_msc->csw, (uint16_t) sizeof(msc_csw_t))); break; case MSC_STAGE_STATUS: @@ -370,7 +370,7 @@ bool msch_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_interface_t const *de MSC_PROTOCOL_BOT == desc_itf->bInterfaceProtocol); // msc driver length is fixed - uint16_t const drv_len = sizeof(tusb_desc_interface_t) + desc_itf->bNumEndpoints*sizeof(tusb_desc_endpoint_t); + uint16_t const drv_len = (uint16_t) (sizeof(tusb_desc_interface_t) + desc_itf->bNumEndpoints * sizeof(tusb_desc_endpoint_t)); TU_ASSERT(drv_len <= max_len); msch_interface_t* p_msc = get_itf(dev_addr); diff --git a/src/host/usbh.c b/src/host/usbh.c index 4c9b0b1ba..b6a03b82e 100644 --- a/src/host/usbh.c +++ b/src/host/usbh.c @@ -665,7 +665,7 @@ static bool usbh_control_xfer_cb (uint8_t dev_addr, uint8_t ep_addr, xfer_result TU_LOG2_MEM(_ctrl_xfer.buffer, xferred_bytes, 2); } - _ctrl_xfer.actual_len = xferred_bytes; + _ctrl_xfer.actual_len = (uint16_t) xferred_bytes; // ACK stage: toggle is always 1 _set_control_xfer_stage(CONTROL_STAGE_ACK); @@ -696,7 +696,7 @@ bool tuh_edpt_xfer(tuh_xfer_t* xfer) TU_VERIFY(usbh_edpt_claim(daddr, ep_addr)); - if ( !usbh_edpt_xfer_with_callback(daddr, ep_addr, xfer->buffer, xfer->buflen, xfer->complete_cb, xfer->user_data) ) + if ( !usbh_edpt_xfer_with_callback(daddr, ep_addr, xfer->buffer, (uint16_t) xfer->buflen, xfer->complete_cb, xfer->user_data) ) { usbh_edpt_release(daddr, ep_addr); return false; @@ -1525,7 +1525,7 @@ static bool _parse_configuration_descriptor(uint8_t dev_addr, tusb_desc_configur } #endif - uint16_t const drv_len = tu_desc_get_interface_total_len(desc_itf, assoc_itf_count, desc_end-p_desc); + uint16_t const drv_len = tu_desc_get_interface_total_len(desc_itf, assoc_itf_count, (uint16_t) (desc_end-p_desc)); TU_ASSERT(drv_len >= sizeof(tusb_desc_interface_t)); // Find driver for this interface diff --git a/src/osal/osal_pico.h b/src/osal/osal_pico.h index abef286b4..8b428d642 100644 --- a/src/osal/osal_pico.h +++ b/src/osal/osal_pico.h @@ -100,11 +100,6 @@ TU_ATTR_ALWAYS_INLINE static inline bool osal_mutex_unlock(osal_mutex_t mutex_hd //--------------------------------------------------------------------+ #include "common/tusb_fifo.h" -#if CFG_TUH_ENABLED -extern void hcd_int_disable(uint8_t rhport); -extern void hcd_int_enable(uint8_t rhport); -#endif - typedef struct { tu_fifo_t ff; diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 93c764caf..13e7778ea 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -262,7 +262,7 @@ static struct hw_endpoint *_next_free_interrupt_ep(void) if (!ep->configured) { // Will be configured by _hw_endpoint_init / _hw_endpoint_allocate - ep->interrupt_num = i - 1; + ep->interrupt_num = (uint8_t) (i - 1); return ep; } } @@ -297,7 +297,7 @@ static struct hw_endpoint *_hw_endpoint_allocate(uint8_t transfer_type) return ep; } -static void _hw_endpoint_init(struct hw_endpoint *ep, uint8_t dev_addr, uint8_t ep_addr, uint wMaxPacketSize, uint8_t transfer_type, uint8_t bmInterval) +static void _hw_endpoint_init(struct hw_endpoint *ep, uint8_t dev_addr, uint8_t ep_addr, uint16_t wMaxPacketSize, uint8_t transfer_type, uint8_t bmInterval) { // Already has data buffer, endpoint control, and buffer control allocated at this point assert(ep->endpoint_control); @@ -329,7 +329,10 @@ static void _hw_endpoint_init(struct hw_endpoint *ep, uint8_t dev_addr, uint8_t | EP_CTRL_INTERRUPT_PER_BUFFER | (ep->transfer_type << EP_CTRL_BUFFER_TYPE_LSB) | dpram_offset; - ep_reg |= bmInterval ? (bmInterval - 1) << EP_CTRL_HOST_INTERRUPT_INTERVAL_LSB : 0; + if (bmInterval) + { + ep_reg |= (uint32_t) ((bmInterval - 1) << EP_CTRL_HOST_INTERRUPT_INTERVAL_LSB); + } *ep->endpoint_control = ep_reg; pico_trace("endpoint control (0x%p) <- 0x%x\n", ep->endpoint_control, ep_reg); ep->configured = true; @@ -341,7 +344,7 @@ static void _hw_endpoint_init(struct hw_endpoint *ep, uint8_t dev_addr, uint8_t // device address // endpoint number / direction // preamble - uint32_t reg = dev_addr | (num << USB_ADDR_ENDP1_ENDPOINT_LSB); + uint32_t reg = (uint32_t) (dev_addr | (num << USB_ADDR_ENDP1_ENDPOINT_LSB)); if (dir == TUSB_DIR_OUT) { @@ -367,39 +370,41 @@ static void _hw_endpoint_init(struct hw_endpoint *ep, uint8_t dev_addr, uint8_t //--------------------------------------------------------------------+ bool hcd_init(uint8_t rhport) { - pico_trace("hcd_init %d\n", rhport); - assert(rhport == 0); + (void) rhport; + pico_trace("hcd_init %d\n", rhport); + assert(rhport == 0); - // Reset any previous state - rp2040_usb_init(); + // Reset any previous state + rp2040_usb_init(); - // Force VBUS detect to always present, for now we assume vbus is always provided (without using VBUS En) - usb_hw->pwr = USB_USB_PWR_VBUS_DETECT_BITS | USB_USB_PWR_VBUS_DETECT_OVERRIDE_EN_BITS; + // Force VBUS detect to always present, for now we assume vbus is always provided (without using VBUS En) + usb_hw->pwr = USB_USB_PWR_VBUS_DETECT_BITS | USB_USB_PWR_VBUS_DETECT_OVERRIDE_EN_BITS; - irq_add_shared_handler(USBCTRL_IRQ, hcd_rp2040_irq, PICO_SHARED_IRQ_HANDLER_HIGHEST_ORDER_PRIORITY); + irq_add_shared_handler(USBCTRL_IRQ, hcd_rp2040_irq, PICO_SHARED_IRQ_HANDLER_HIGHEST_ORDER_PRIORITY); - // clear epx and interrupt eps - memset(&ep_pool, 0, sizeof(ep_pool)); + // clear epx and interrupt eps + memset(&ep_pool, 0, sizeof(ep_pool)); - // Enable in host mode with SOF / Keep alive on - usb_hw->main_ctrl = USB_MAIN_CTRL_CONTROLLER_EN_BITS | USB_MAIN_CTRL_HOST_NDEVICE_BITS; - usb_hw->sie_ctrl = SIE_CTRL_BASE; - usb_hw->inte = USB_INTE_BUFF_STATUS_BITS | - USB_INTE_HOST_CONN_DIS_BITS | - USB_INTE_HOST_RESUME_BITS | - USB_INTE_STALL_BITS | - USB_INTE_TRANS_COMPLETE_BITS | - USB_INTE_ERROR_RX_TIMEOUT_BITS | - USB_INTE_ERROR_DATA_SEQ_BITS ; + // Enable in host mode with SOF / Keep alive on + usb_hw->main_ctrl = USB_MAIN_CTRL_CONTROLLER_EN_BITS | USB_MAIN_CTRL_HOST_NDEVICE_BITS; + usb_hw->sie_ctrl = SIE_CTRL_BASE; + usb_hw->inte = USB_INTE_BUFF_STATUS_BITS | + USB_INTE_HOST_CONN_DIS_BITS | + USB_INTE_HOST_RESUME_BITS | + USB_INTE_STALL_BITS | + USB_INTE_TRANS_COMPLETE_BITS | + USB_INTE_ERROR_RX_TIMEOUT_BITS | + USB_INTE_ERROR_DATA_SEQ_BITS ; - return true; + return true; } void hcd_port_reset(uint8_t rhport) { - pico_trace("hcd_port_reset\n"); - assert(rhport == 0); - // TODO: Nothing to do here yet. Perhaps need to reset some state? + (void) rhport; + pico_trace("hcd_port_reset\n"); + assert(rhport == 0); + // TODO: Nothing to do here yet. Perhaps need to reset some state? } void hcd_port_reset_end(uint8_t rhport) @@ -409,25 +414,27 @@ void hcd_port_reset_end(uint8_t rhport) bool hcd_port_connect_status(uint8_t rhport) { - pico_trace("hcd_port_connect_status\n"); - assert(rhport == 0); - return usb_hw->sie_status & USB_SIE_STATUS_SPEED_BITS; + (void) rhport; + pico_trace("hcd_port_connect_status\n"); + assert(rhport == 0); + return usb_hw->sie_status & USB_SIE_STATUS_SPEED_BITS; } tusb_speed_t hcd_port_speed_get(uint8_t rhport) { - assert(rhport == 0); - // TODO: Should enumval this register - switch (dev_speed()) - { - case 1: - return TUSB_SPEED_LOW; - case 2: - return TUSB_SPEED_FULL; - default: - panic("Invalid speed\n"); - return TUSB_SPEED_INVALID; - } + (void) rhport; + assert(rhport == 0); + // TODO: Should enumval this register + switch (dev_speed()) + { + case 1: + return TUSB_SPEED_LOW; + case 2: + return TUSB_SPEED_FULL; + default: + panic("Invalid speed\n"); + return TUSB_SPEED_INVALID; + } } // Close all opened endpoint belong to this device @@ -465,15 +472,17 @@ uint32_t hcd_frame_number(uint8_t rhport) void hcd_int_enable(uint8_t rhport) { - assert(rhport == 0); - irq_set_enabled(USBCTRL_IRQ, true); + (void) rhport; + assert(rhport == 0); + irq_set_enabled(USBCTRL_IRQ, true); } void hcd_int_disable(uint8_t rhport) { - // todo we should check this is disabling from the correct core; note currently this is never called - assert(rhport == 0); - irq_set_enabled(USBCTRL_IRQ, false); + (void) rhport; + // todo we should check this is disabling from the correct core; note currently this is never called + assert(rhport == 0); + irq_set_enabled(USBCTRL_IRQ, false); } //--------------------------------------------------------------------+ @@ -488,6 +497,7 @@ bool hcd_edpt_open(uint8_t rhport, uint8_t dev_addr, tusb_desc_endpoint_t const // Allocated differently based on if it's an interrupt endpoint or not struct hw_endpoint *ep = _hw_endpoint_allocate(ep_desc->bmAttributes.xfer); + TU_ASSERT(ep); _hw_endpoint_init(ep, dev_addr, @@ -510,7 +520,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * // Get appropriate ep. Either EPX or interrupt endpoint struct hw_endpoint *ep = get_dev_ep(dev_addr, ep_addr); - assert(ep); + TU_ASSERT(ep); // EP should be inactive assert(!ep->active); @@ -532,7 +542,7 @@ bool hcd_edpt_xfer(uint8_t rhport, uint8_t dev_addr, uint8_t ep_addr, uint8_t * // That has set up buffer control, endpoint control etc // for host we have to initiate the transfer - usb_hw->dev_addr_ctrl = dev_addr | (ep_num << USB_ADDR_ENDP_ENDPOINT_LSB); + usb_hw->dev_addr_ctrl = (uint32_t) (dev_addr | (ep_num << USB_ADDR_ENDP_ENDPOINT_LSB)); uint32_t flags = USB_SIE_CTRL_START_TRANS_BITS | SIE_CTRL_BASE | (ep_dir ? USB_SIE_CTRL_RECEIVE_DATA_BITS : USB_SIE_CTRL_SEND_DATA_BITS); @@ -556,11 +566,12 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet #pragma GCC diagnostic push #pragma GCC diagnostic ignored "-Warray-bounds" #pragma GCC diagnostic ignored "-Wstringop-overflow" - memcpy((void*)&usbh_dpram->setup_packet[0], setup_packet, 8); + memcpy((void*) (uintptr_t) &usbh_dpram->setup_packet[0], setup_packet, 8); #pragma GCC diagnostic pop // Configure EP0 struct with setup info for the trans complete struct hw_endpoint *ep = _hw_endpoint_allocate(0); + TU_ASSERT(ep); // EPX should be inactive assert(!ep->active); -- cgit v1.3.1 From 9c56f7011171ff649a821fe87a3ee477299fa860 Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 27 Jun 2022 20:30:47 +0700 Subject: suppress error with net example --- examples/device/net_lwip_webserver/CMakeLists.txt | 2 ++ examples/make.mk | 3 ++- src/class/net/ecm_rndis_device.c | 6 +++--- 3 files changed, 7 insertions(+), 4 deletions(-) (limited to 'src') diff --git a/examples/device/net_lwip_webserver/CMakeLists.txt b/examples/device/net_lwip_webserver/CMakeLists.txt index beaa9ad99..0f41b888a 100644 --- a/examples/device/net_lwip_webserver/CMakeLists.txt +++ b/examples/device/net_lwip_webserver/CMakeLists.txt @@ -76,6 +76,8 @@ if (EXISTS ${TOP}/lib/lwip/src) target_compile_options(${PROJECT} PUBLIC -Wno-error=null-dereference -Wno-error=conversion + -Wno-error=sign-conversion + -Wno-error=sign-compare ) # Configure compilation flags and libraries for the example... see the corresponding function diff --git a/examples/make.mk b/examples/make.mk index fa909ddca..27e1db38c 100644 --- a/examples/make.mk +++ b/examples/make.mk @@ -113,7 +113,8 @@ CFLAGS += \ -Wunused \ -Wredundant-decls -# -Wconversion \ +# conversion is too strict for most mcu driver, may be disable sign/int/arith-conversion +# -Wconversion # Debugging/Optimization ifeq ($(DEBUG), 1) diff --git a/src/class/net/ecm_rndis_device.c b/src/class/net/ecm_rndis_device.c index d85a3f778..5f316762f 100644 --- a/src/class/net/ecm_rndis_device.c +++ b/src/class/net/ecm_rndis_device.c @@ -318,11 +318,11 @@ bool netd_control_xfer_cb (uint8_t rhport, uint8_t stage, tusb_control_request_t rndis_generic_msg_t *rndis_msg = (rndis_generic_msg_t *) ((void*) notify.rndis_buf); uint32_t msglen = tu_le32toh(rndis_msg->MessageLength); TU_ASSERT(msglen <= sizeof(notify.rndis_buf)); - tud_control_xfer(rhport, request, notify.rndis_buf, msglen); + tud_control_xfer(rhport, request, notify.rndis_buf, (uint16_t) msglen); } else { - tud_control_xfer(rhport, request, notify.rndis_buf, sizeof(notify.rndis_buf)); + tud_control_xfer(rhport, request, notify.rndis_buf, (uint16_t) sizeof(notify.rndis_buf)); } } break; @@ -369,7 +369,7 @@ static void handle_incoming_packet(uint32_t len) } } - if (!tud_network_recv_cb(pnt, size)) + if (!tud_network_recv_cb(pnt, (uint16_t) size)) { /* if a buffer was never handled by user code, we must renew on the user's behalf */ tud_network_recv_renew(); -- cgit v1.3.1 From 25580b4fe9acd1d9f9f12cbfdd29037669376a8d Mon Sep 17 00:00:00 2001 From: hathach Date: Mon, 27 Jun 2022 21:05:41 +0700 Subject: use forloop to avoid -Warray-bounds with host setup packet --- src/portable/raspberrypi/rp2040/hcd_rp2040.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) (limited to 'src') diff --git a/src/portable/raspberrypi/rp2040/hcd_rp2040.c b/src/portable/raspberrypi/rp2040/hcd_rp2040.c index 13e7778ea..e9118c6a3 100644 --- a/src/portable/raspberrypi/rp2040/hcd_rp2040.c +++ b/src/portable/raspberrypi/rp2040/hcd_rp2040.c @@ -563,11 +563,10 @@ bool hcd_setup_send(uint8_t rhport, uint8_t dev_addr, uint8_t const setup_packet (void) rhport; // Copy data into setup packet buffer -#pragma GCC diagnostic push -#pragma GCC diagnostic ignored "-Warray-bounds" -#pragma GCC diagnostic ignored "-Wstringop-overflow" - memcpy((void*) (uintptr_t) &usbh_dpram->setup_packet[0], setup_packet, 8); -#pragma GCC diagnostic pop + for(uint8_t i=0; i<8; i++) + { + usbh_dpram->setup_packet[i] = setup_packet[i]; + } // Configure EP0 struct with setup info for the trans complete struct hw_endpoint *ep = _hw_endpoint_allocate(0); -- cgit v1.3.1