Signed-off-by: Wolfgang Denk <wd@denx.de>

* 'master' of git://git.denx.de/u-boot-sh:
  sh: ecovec: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  sh: Fix rsk7264 pin setup for on-board ethernet

When calling board_late_init, we need to define CONFIG_BOARD_LATE_INIT.
The latest ecovec config defines BOARD_LATE_INIT, board_late_init is not called.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This sets up the external ethernet IRQ pin.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Do the same AXI cache and Qos settings done already in the
SabreLite imximage.cfg for the ARM2 board, too.

It fixes a display flash issue caused by low priority of
the display IDMA channel.

Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
CC: Jason Chen <b02280@freescale.com>
CC: Jason Liu <r64343@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
Acked-by: Jason Liu <r64343@freescale.com>

Signed-off-by: Wolfgang Denk <wd@denx.de>

* 'master' of git://git.denx.de/u-boot-arm:
  ARM926EJS: Fix cache.c to comply with checkpatch.pl
  ARM926EJS: Make asm routines volatile in cache ops
  MX35: mx35pdk: wrong board revision
  ARM1136: MX35: Make asm routines volatile in cache ops
  ARM: add u-boot.imx as target for i.MX SOCs
  M28: Pull out CONFIG_APBH_DMA so it's always enabled
  DMA: Split the APBH DMA init into block and channel init
  imx: Return gpio_set_value in gpio_direction_output
  imx: Use GPIO_TO_PORT macro in the gpio driver instead of (gpio >> 5)
  imx: Add GPIO_TO_PORT macro in the mxc_gpio driver
  imx: Remove unneeded/repititive definitions from imx headers
  i.MX28: Allow coexistence of PIO and DMA mode for SD/MMC
  MX31: mx31pdk: drop enable_caches from board file
  i.MX28: Fix initial stack pointer position
  mx35: mx35pdk: fix when cache functions are linked
  mx35: flea3: fix when cache functions are linked
  ARM: 926ejs: use debug() for misaligned addresses
  ARM1136: add cache flush and invalidate operations
  mx6qsabrelite: Fix the serial console port
  mx6qsabrelite: Add boot switch setting information into the README
  i.MX6: mx6qsabrelite: add cache commands if cache is enabled
  i.MX6: implement enable_caches()
  i.MX6: define CACHELINE_SIZE
  MX53: DDR: Fix ZQHWCTRL field TZQ_CS
  mx28evk: Add a README file
  mx28: Split the README into a common part and a m28 specific part
  tricorder: Load kernel from ubifs
  tricorder: Add UBIFS
  cm-t35: fix Ethernet reset timing
  hawkboard: Add CONFIG_SPL_LIBGENERIC_SUPPORT
  BeagleBoard: Remove userbutton command and use gpio command instead
  OMAP: Move omap1510inn to Unmaintained / Orphaned

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>

We certainly don't want the compiler to reorganise the code for dcache flushing.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Stefano Babic <sbabic@denx.de>

The board revision is detected accessing to the pmic,
that is not available before relocation (I2C).
This generates the following error:

CPU:   Freescale i.MX35 rev 2.0 at 532 MHz.
Reset cause: WDOG
<reg num> = 7 is invalid. Should be less than 0
Board: MX35 PDK 1.0

The revision number is wrong, as a default value is printed
(tested on a mx35pdk Rev. 2.0).

Move the output in the board_late_init(), when
pmic can be accessed.

Signed-off-by: Stefano Babic <sbabic@denx.de>