u-boot.git, branch v2013.07

Prepare v2013.07

2013-07-23T11:58:13+00:00

Signed-off-by: Tom Rini

fs/ext4: fix log2blksz un-initialized error, by cacaulating its value from blksz

2013-07-22T14:09:56+00:00

The problem here is that uboot can't mount ext4 filesystem with
commit "50ce4c07df1" applied. We use hard-coded "SECTOR_SIZE"(512)
before this commit, now we introduce (block_dev_desc_t *)->log2blksz
to replace this macro. And after we calling do_ls()->fs_set_blk_dev(),
the variable log2blksz is not initialized, which it's not correct.

And this patch try to solve the problem by caculating the value of
log2blksz from variable blksz.

ext4fs: le32_to_cpu() used on a 16-bit field

2013-07-22T14:09:30+00:00

Fix reading ext4_extent_header struture on BE machines.  Some 16 bit
fields where converted to 32 bit fields, due to the byte swap on BE
machines the containing value was corrupted. Therefore reading ext4
filesystems on BE machines where broken before.

Signed-off-by: Rommel Custodio 
[sent via git-send-email; rework commit message]
Signed-off-by: Andreas Bießmann 
Reviewed-by: Simon Glass 
Tested-by: Simon Glass 
Tested-by: Lukasz Majewski

arm: at91sam9n12: change EBI IO to high drive mode

2013-07-22T12:20:14+00:00

As both the DDR SDRAM and NAND flash connect to EBI on at91sam9n12
and share the lower 8 bits data line. If use low drive of the data
line, it will cause DDR data access corrupt in lower address, so
change the data line to high drive mode

This will fix the Linux kernel boot issue when use Lower address

Signed-off-by: Bo Shen 
Acked-by: Andreas Bießmann

ddr cfg: DRAM_RESET needs 0x00020030

2013-07-20T16:14:09+00:00

The old value of 0x000e0030 will cause ethernet
timeout issues on the sabrelite and possibly other
boards using the KSZ9021.
I have no explanation as to why.

But this is a correct change, the TRM will be updated
to show that 00b is the only valid setting for bits
19-18 of DRAM_RESET.

My thanks go to Liu Hui(Jason) for this information.

Acked-by: Fabio Estevam 
Acked-by: Stefano Babic 
Signed-off-by: Troy Kisky

net: phy: Set SUPPORTED_1000baseX_Half flag in ESTATUS_1000_XHALF case

2013-07-19T21:12:20+00:00

Commit de1d786e (add support for Xilinx 1000BASE-X phy (GTX)) introduced the
checking for ESTATUS_1000_XHALF, but it incorrectly sets the
SUPPORTED_1000baseX_Full flag in this case.

Set the SUPPORTED_1000baseX_Half flag instead.

Acked-by: Charles Coldwell 
Reviewed-By: Sascha Silbe 
Reviewed-by: Joe Hershberger 
Signed-off-by: Fabio Estevam

phy: fix 10/100Mbps operation on 1Gbps-capable links

2013-07-19T21:12:16+00:00

de1d786 [add support for Xilinx 1000BASE-X phy (GTX)] introduced a
check for the extended status register in order to support
1Gbps-capable PHYs that don't have the 1000BASE-T registers. Since
Extended Status only indicates what the PHY (i.e. the local side) is
capable of, this broke communication with non-1Gbps peers.

Only check the extended status if the 1000BASE-T registers are
actually missing so we don't end up setting speed to 1Gbps even though
the previous test (for the combination of local and peer support for
1Gbps) already indicated we can't do 1Gbps with the current peer.

Signed-off-by: Sascha Silbe 
Tested-by: Fabio Estevam 
Reviewed-by: Joe Hershberger

mkimage: Use board config to get CONFIG_FIT_SIGNATURE value

2013-07-19T13:45:19+00:00

The value of this config variable is not available to image.h on the host,
since the board config is not actually included. Bring this in so that
mkimage will be built with image-signing support for sandbox at least.

Signed-off-by: Simon Glass

arm:trats:fix: Correction of loaddtb environment variable.

2013-07-19T12:30:10+00:00

Missing space for loaddtb command has been added. When missing, ext4load
fails with wrong number of passed parameters.

Acked-by: Minkyu Kang 
Signed-off-by: Lukasz Majewski

bootm: Move fixup_silent_linux() earlier in the bootm stages

2013-07-17T14:37:11+00:00

Before the bootm refactor, fixup_silent_linux() was done only in the
monolithic bootm case, not in the subcommand case. With the refactor, it
is done always, which is good. Unfortunately it is done too late, since it
is the PREP or CMDLINE stages that set up the command line for Linux.

Move fixup_silent_linux() into the LOADOS stage, which is where we find
out the OS being used, and can thus decide whether to perform this step.

Signed-off-by: Simon Glass