u-boot.git, branch v2015.10-rc4

Prepare v2015.10-rc4

2015-09-28T20:57:42+00:00

Signed-off-by: Tom Rini

mmc: dw_mmc: Increase timeout to 4 minutes (as in Linux kernel)

2015-09-28T15:03:56+00:00

The commit: d9dbb97be0e4a550457aec5f11afefb446169c90
"mmc: dw_mmc: Zap endless timeout" removed endless loop waiting for end
of dw mmc transfer.

For some workloads - dfu test @ Odroid XU3 (sending 8MiB file) -
and SD cards (e.g. MicroSD Kingston 4GiB, Adata 4GiB)
the default timeout is to short.

The new value - 4 minutes (240 seconds) - is the same as the one used in
Linux kernel driver. Such fix should be good enough until we come up
with better fix for this issue.

Signed-off-by: Lukasz Majewski 
Cc: Marek Vasut 
Cc: Pantelis Antoniou 
Cc: Tom Rini 
Tested-by: Przemyslaw Marczak

tools: moveconfig: Update the URL for nds32 toolchain

2015-09-28T15:03:55+00:00

Give a full URL for a working nds32 toolchain for U-Boot.

Signed-off-by: Bin Meng 
Reviewed-by: Masahiro Yamada

tools: gen_eth_addr: add getpid() to time(0) to avoid duplicated seed

2015-09-28T14:48:25+00:00

As 'time(0) | getpid()' will have a lot of duplicated value. It is not a
expected behavior. We expect different value for the seed when when run
it in many times.

So this patch will left shift the getpid() and add to time(0). That
avoid duplicated value.

Test command is like:
  % RUN=0; while [ $RUN -lt 10000 ]; do
  tools/gen_eth_addr; RUN=$(($RUN+1)); done | sort | uniq | wc -l
  10000

This patch is incorporated with suggestions made by Wolfgang Denk and Andreas
Bießmann. Thanks them a lot.

Signed-off-by: Josh Wu 
Acked-by: Andreas Bießmann 
Acked-by: Wolfgang Denk 
Tested-by: Wolfgang Denk

arm: Drop old non-generic-board code

2015-09-28T14:48:24+00:00

This code is no-longer used. Drop it.

Signed-off-by: Simon Glass 
Acked-by: Andreas Bießmann

arm: Remove wireless_space board

2015-09-28T14:48:24+00:00

This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass

arm: Remove da830evm board

2015-09-28T14:48:23+00:00

This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass

ARM: hikey: Adjust SDRAM_1_SIZE to 0x3EFFFFFF

2015-09-28T14:48:23+00:00

DRAM region 0x3f000000 - 0x3fffffff is reserved for OP-TEE. Touching
0x3f000000 memory location from unsecure world causes the board
to hang.

Signed-off-by: Peter Griffin 
Reviewed-by: Simon Glass

ARM: hikey: hi6220: Migrate over to DM_SERIAL and use UART3 by default.

2015-09-28T14:48:22+00:00

Use DM for the pl01x serial driver on hikey. Also allow UART0 or
UART3 to be chosen via Kconfig.

By default we now output to UART3 as the latest version of ATF outputs
to this UART. Also UART3 comes out on the LS connector, as opposed to
UART0 which goes to a unpopulated header.

As part of this change we also enable CONFIG_BOARD_EARLY_INIT_F and
call the pinmux configuration code for the UART. Before we were
relying on ATF having already configured the pin configuration.

NB: Upstream Linux kernel doesn't yet support UART3, so serial console
will still be output on UART0 when booting a upstream kernel.

Signed-off-by: Peter Griffin 
Reviewed-by: Simon Glass

ARM: hikey: Select DM, DM_GPIO from Kconfig

2015-09-28T14:48:22+00:00

Most platforms enable these options from Kconfig rather
than the configs header file.

Signed-off-by: Peter Griffin 
Reviewed-by: Simon Glass