u-boot.git, branch v2016.11

Prepare v2016.11

2016-11-14T16:27:11+00:00

Signed-off-by: Tom Rini

MAINTAINERS: mark sunxi status as Orphan

2016-11-14T16:24:44+00:00

Ian has not had any time for sunxi for some time now and I'm
in the same situation now, so I'm stepping down as sunxi
custodian and marking the sunxi support as Orphan.

Cc: Maxime Ripard 
Cc: Chen-Yu Tsai 
Cc: Ian Campbell 
Signed-off-by: Hans de Goede 
Acked-by: Ian Campbell

video: bmp: Fix compilation errors with CONFIG_BMP_xxBPP enabled

2016-11-13T20:54:38+00:00

Compiling the 'bmp' command with DM and having one of the following macros
enabled:

CONFIG_BMP_16BPP, CONFIG_BMP_24BPP ONFIG_BMP_32BPP

generates this error:

drivers/video/video_bmp.c: In function ‘video_bmp_display’:
drivers/video/video_bmp.c:315:22: error: ‘lcd_line_length’ undeclared (first use in this function)
    fb -= width * 2 + lcd_line_length;
                          ^

This patch moves to using the correct variable instead and enables the
'bmp' command for DM again.

Signed-off-by: Stefan Roese 
Cc: Simon Glass 
Cc: Anatolij Gustschin

net: write enetaddr down to hardware on env_callback

2016-11-13T20:54:38+00:00

If mac-address is changed using "setenv ethaddr ...." command the new
mac-adress also must be written into the responsible ethernet driver.
This fixes the legacy ethernet handling.

Signed-off-by: Marek Vasut 
Cc: Hannes Schmelzer 
Cc: Joe Hershberger 
Cc: Tom Rini 
Reviewed-by: Hannes Schmelzer

spi: ti_qspi: Fix baudrate divider calculation

2016-11-13T20:54:37+00:00

Fix the divider calculation logic to choose a value so that the
resulting baudrate is either equal to or closest possible baudrate less
than the requested value. While at that, cleanup ti_spi_set_speed().

Signed-off-by: Vignesh R 
Reviewed-by: Jagan Teki

ARM: dts: dra7xx: Update spi-max-frequency for qspi slave node

2016-11-13T20:54:37+00:00

Update the spi-max-frequency property of m25p80 flash slave to match
that of TI QSPI controller node, so that QSPI operations happen at
maximum supported frequency of 76.8MHz.

Signed-off-by: Vignesh R 
Reviewed-by: Jagan Teki

ARM: k2g: Update PLL Multiplier and divider values

2016-11-13T20:54:37+00:00

Only a certain set of PLLM/D values are recommended to configure the DDR
at the required speeds for a given clock input frequency. Updating these
values as specified in Data Sheet[1] Table 5-18

[1] http://www.ti.com/lit/ds/symlink/66ak2g02.pdf

Signed-off-by: Lokesh Vutla 
Reviewed-by: Tom Rini

ARM: keystone2: PLL: Enable glitch free initialization sequence

2016-11-13T20:54:36+00:00

Update the PLL initialization sequence to avoid glitches while
programming. User guide for the same is available at[1].

[1] http://www.ti.com/lit/ug/sprugv2h/sprugv2h.pdf

Signed-off-by: Lokesh Vutla 
Reviewed-by: Tom Rini

arm: Set TTB XN bit in case DCACHE_OFF for LPAE mode

2016-11-13T20:54:36+00:00

While we setup the mmu initially we mark set_section_dcache with
DCACHE_OFF flag. In case of non-LPAE mode the DCACHE_OFF macro
is rightly defined with TTB_SECT_XN_MASK set so as to mark all the
4GB XN. In case of LPAE mode  XN(Execute-never) bit is not set with
DCACHE_OFF. Hence XN bit is not set by default for DCACHE_OFF which
keeps all the regions execute okay and this leads to random speculative
fetches in random memory regions which was eventually caught by kernel
omap-l3-noc driver.

Fix this to mark the regions as XN by default.

Signed-off-by: Keerthy 
Reviewed-by: Alexander Graf 
Reviewed-by: Tom Rini

arm: print the cache config option in hex instead of decimal

2016-11-13T20:54:36+00:00

Printing the option value in hex makes it more comprehensible.

Signed-off-by: Keerthy 
Reviewed-by: Tom Rini