u-boot.git, branch v2019.04-rc3

Prepare v2019.04-rc4

2019-03-05T02:46:24+00:00

Signed-off-by: Tom Rini

Merge branch 'master' of git://git.denx.de/u-boot-sh

2019-03-04T21:35:40+00:00

- Assorted PFC fixes

Merge tag 'u-boot-atmel-2019.04-a' of git://git.denx.de/u-boot-atmel

2019-03-04T18:06:22+00:00

First set of u-boot-atmel fixes for 2019.04 cycle

Merge git://git.denx.de/u-boot-fsl-qoriq

2019-03-04T18:05:53+00:00

- Enable DHCP as boot-source in distro boot for NXP layerscape
  platforms
- fix register layout for SEC on Layerscape architectures
- fixes related to DPAA2 ethernet

configs: at91: remove SPL_GENERATE_ATMEL_PMECC_HEADER from non-nand configs

2019-03-04T07:13:04+00:00

SPL_GENERATE_ATMEL_PMECC_HEADER will generate a header for the SPL for NAND
information. The initial stage 1 bootloader will use this header in case the
NAND flash doesn't support commands to retrieve sector size, etc.
However this header is bad for different boot media, like MMC or SPI.
In case SD_BOOT or SPI_BOOT is used, remove the config for this.

Signed-off-by: Eugen Hristev

configs: sama5d27_som1_ek: Activate misc init for uSD variant

2019-03-04T07:13:04+00:00

This was already set for 'sama5d27_som1_ek_mmc_defconfig' (first SD
card, full size). Without this option set, the MAC address is not read
from the I²C EEPROM at boot, and remains unset:

    U-Boot 2019.01 (Jan 01 2019 - 00:00:00 +0000)

    CPU: SAMA5D27 1G bits DDR2 SDRAM
    Crystal frequency:       24 MHz
    CPU clock        :      492 MHz
    Master clock     :      164 MHz
    DRAM:  128 MiB
    MMC:   sdio-host@a0000000: 0, sdio-host@b0000000: 1
    Loading Environment from FAT... OK
    In:    serial
    Out:   serial
    Err:   serial
    Net:
    Error: ethernet@f8008000 address not set.
    eth-1: ethernet@f8008000
    Hit any key to stop autoboot:  0

Signed-off-by: Alexander Dahl

pinctrl: renesas: r8a77990: Reivse USB ID pin name

2019-03-04T00:46:05+00:00

Since the datasheet Rev.1.00 has an error about the USB ID pin name,
this patch revises it.

Signed-off-by: Hiroyuki Yokoyama 
Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu

pinctrl: renesas: r8a77990: Fix MOD_SEL0 bit3 when using TX0

2019-03-04T00:46:05+00:00

According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50,
the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is selected,
and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is
selected.

Signed-off-by: Hiroyuki Yokoyama 
Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu

pinctrl: renesas: r8a77990: Fix MOD_SEL0 bit16 when using NFALE and NFRB_N

2019-03-04T00:46:05+00:00

According to the R-Car Gen3 Hardware Manual Rev.1.50, the MOD_SEL0
bit16 is set to 0 when NFALE_A and NFRB_N_A pin functions are
selected.

Signed-off-by: Hiroyuki Yokoyama 
Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu

pinctrl: renesas: r8a77990: Fix MOD_SEL0 bit2 when using RX2,TX2 and SCK2

2019-03-04T00:46:05+00:00

According to the R-Car Gen3 Hardware Manual Rev 1.50, the MOD_SEL0
bit2 is set when RX2_{A,B}, TX2_{A,B} and SCK2_A pin functions are
selected.

Signed-off-by: Hiroyuki Yokoyama 
Signed-off-by: Marek Vasut 
Cc: Nobuhiro Iwamatsu