Signed-off-by: Tom Rini <trini@konsulko.com>

- micrel, ti PHY fixes
- rtl8169, mtk-eth fixes

STM32 MCUs update:
_ Add MPU region for SPI NOR memory mapped region
_ Add missing QSPI flash compatible for STM32 F7 boards
_ Update spi-tx-bus-width and spi-rx-bus-width properties
_ Add QSPI support for STM32F469 Discovery board

In mt7629-rfb.dts, the phy-handle is a reference to the node phy0, not the
node itself:

	phy-handle = <&phy0>;

	phy0: ethernet-phy@0 {
		reg = <0>;
	}

However the driver used ofnode_find_subnode("phy-handle") to read the node.
It will always fail.

This patch replaces ofnode_find_subnode with dev_read_phandle_with_args to
make sure the node can be read correctly.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

This version of the RTL-8168 is present on some development boards and
is compatible with this driver. Add support for identifying this version
of the chip so that U-Boot won't complain about it being unknown.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Implement this callback that allows the MAC address to be set for the
Ethernet card. This is necessary in order for the device to be able to
receive packets for the MAC address that U-Boot advertises.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

There is a need to fill node before clk_output_sel is setup.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: <hannes.schmelzer@br-automation.com>

Commit d397f7c45b0b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.

Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

Pull request for UEFI sub-system for v2019.07-rc3

The development target for the UEFI sub-system is EBBR compliance. We have
already implemented some further protocols to enable running the UEFI Shell
and the UEFI SCT test suite.

As some boards are severely memory constrained make some of these extras
customizable.

Provide bug fixes. The most prominent ones let us pass the UEFI SCT memory
allocation tests.

- A10 FPGA programming support, Gen5 livetree conversion