Signed-off-by: Tom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

With recent update in u-boot gitattributes all files are treated as regular
text files. This creates problems with special files and repo always
shows uncommitted files like below.

Your branch is up-to-date with 'origin/master'.
Changes not staged for commit:
  (use "git add <file>..." to update what will be committed)
  (use "git checkout -- <file>..." to discard changes in working directory)

	modified:   tools/logos/compulab.bmp
	modified:   tools/logos/denx-comp.bmp
	modified:   tools/logos/toradex.bmp

To fix above problem special files bmp/ttf files are treated as binary
files in the gitattributes.

Signed-off-by: Vignesh Rajendran <vignesh.rajendran@in.bosch.com>
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>

The generated idbloader.img file that rockchip uses should
be not included in git status report

Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>

A recent change adjusted the symbol calculation to work on x86 but broke
it for Tegra. In fact this is because they have different needs.

On x86 devices the code is linked to a ROM address and the end-at-4gb
property is used for the image. In this case there is no need to add the
base address of the image, since the base address is already built into
the offset and image-pos properties.

On other devices we must add the base address since the offsets start at
zero.

In addition the base address is currently added to the 'offset' and 'size'
values. It should in fact only be added to 'image-pos', since 'offset' is
relative to its parent and 'size' is not actually an address. This code
should have been adjusted when support for 'image-pos' and 'size' was
added, but it was not.

To correct these problems:
- move the code that handles adding the base address to section.py, which
  can check the end-at-4gb property and which property
  (offset/size/image-pos) is being read
- add the base address only when needed (only for image-pos and not if the
  image uses end-at-4gb)
- add a note to the documentation
- add a separate test to cover x86 behaviour

Fixes: 15c981cc (binman: Correct symbol calculation with non-zero image base)

Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>

- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.

- Rename CONFIG_SECURE_BOOT to CONFIG_NXP_ESBC.
- Few bug fixes and updates related to SPI, hwconfig, ethernet,
  fsl-layerscape, pci, icid, PSCI

This patch enable TPL support for firefly-rk3288 board, which works ths
same way with other RK3288 board like Tinker, evb.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>

Without the prefix, "same-as-spl" in `u-boot,spl-boot-order` will not work
as expected. When board_boot_order() `spl-boot-order.c` meets
"same-as-spl", it gets the conf by looking the boot_devices table by boot
source, and parse the node by the conf with:

   node = fdt_path_offset(blob, conf);

which will failed without the "/" indicating the path.

Currently only entries of boot_devices in rk3399 have the "/" prefix.
Therefore add the missing ones in other boards.

Signed-off-by: Levin Du <djw@t-chip.com.cn>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

Since we move the ATF bl31 entry for 64bit CPUs to 0x40000, we need to
limit the SPL size in 0x40000(start from 0) so that we don't need to do
the relocate for ATF loading.
Note that there will be separate BSS, STACK and MALLOC heap, so the size
0x40000(256KB) should be enough for SPL text.

Signed-off-by: Kever Yang <kever.yang@rock-chips.com>