Signed-off-by: Tom Rini <trini@konsulko.com>

Both dummy.nbytes and dummy.buswidth may be zero. By not checking
the later, it is possible to trigger division by zero and a crash.
This does happen with tiny SPI NOR framework in SPL. Fix this by
adding the check and returning zero dummy bytes in such a case.

Fixes: 38b0852b0ea ("spi: cadence-qspi: Add support for octal DTR flashes")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
[trini: Drop Pratyush's RB as his requested changes weren't made as
        Marek disagreed]

Rebuild our current docker image so that ca-certificates will be updated
and Let's Encrypt issued certificates will work again.

Signed-off-by: Tom Rini <trini@konsulko.com>

- fix usb stopt; usb start; bug
- update Nicolas email address

- Armada8k: Fix CP0 eMMC/SDIO support (Robert)

XHCI firmware upload must be performed only once after initializing the
PCI bridge. This fixes USB stack initialization after calling "usb stop;
usb start" on Raspberry Pi 4B.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>

The @suse.de address doesn't exist anymore. Update it to something not
dependent on my workplace.

Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>

During the migration to a single DTSI for the CP110-s specific pinctrl
compatibles were moved to the SoC DTSI as CP0 and CP1 have some specifics.
Namely, CP0 eMMC/SDIO support depends on the mvebu-pinctrl driver setting
the BIT(0) in eMMC PHY IO Control 0 Register to 0 in order for the connect
the eMMC/SDIO PHY to the controller and not use it as a MPP pin multiplexor.

So, the mvebu-pinctrl driver check specifically for the
"marvell,armada-8k-cpm-pinctrl" compatible to clear the that bit.

Issue is that compatibles in the 8040 DTSI were set to "marvell,8k-cpm-pinctrl"
for CP0 and "marvell,8k-cps-pinctrl" for the CP1.
This is obviously incorrect as the pinctrl driver does not know about these.

So fix the regression by applying correct compatibles to the DTSI.
Regression found and tested on the Puzzle M801 board.

Fixes: a0ba97e5 ("arm: armada: dts: Use a single dtsi for cp110 die description")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>

- Reintroduce creating internally the "nor%d" style names, in order to
  fix some use U-Boot use-cases involving the "mtd" command.
- Fix a regression over the default SPI bus mode shown by having the
  compiled default actually start being used.  The correct default here
  is 0.
- Fix ethernet on imx7d-sdb
- Fix a regression with MTD NAND devices when OF_LIVE is enabled

Commit 0d52bab46 (mx7dsabre: Enable DM_ETH) changed these flags from 0
(aka GPIO_ACTIVE_HIGH) to GPIO_ACTIVE_LOW. It claimed to "Also sync
device tree with v5.5-rc1", but in the linux tree, these gpios have
always been GPIO_ACTIVE_HIGH ever since this node was introduced
around v4.13 (linux commit 184f39b5).

I'm guessing that the reason for the GPIO_ACTIVE_LOW was to work
around the behaviour of the soft-spi driver back then, which
effectively defaulted to spi-mode 3 and not 0. That was arguably a bug
in the soft-spi driver, which then got fixed in 0e146993bb3 (spi: add
support for all spi modes with soft spi), but that commit then broke
ethernet on this board.

Fix it by setting the gpios as active high, which as a bonus actually
brings us in sync with the .dts in the linux source tree.

Without this, one gets

    Net:   Could not get PHY for FEC0: addr 0
    No ethernet found.

With this, ethernet (at least ping and tftp) works as expected from
the U-Boot shell.

Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joris Offouga <offougajoris@gmail.com>
Cc: "Christian Bräuner Sørensen" <yocto@bsorensen.net>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>