Previously MAKEALL would always return a value of 0, even if 1 or more
boards did not compile.  This change causes MAKEALL to return 0 if all
boards were able to build, otherwise 1.

This change also requires changing the script interpreter from sh to
bash to support bash's PIPESTATUS variable.

Signed-off-by: Peter Tyser <ptyser@xes-inc.com>

Start of support of
Texas Instruments Software Development Platform(SDP)
for OMAP3430 - SDP3430

Highlights of this platform are:
Flash Memory devices:
	Sibley NOR, Micron 8bit NAND and OneNAND
Connectivity:
	3 UARTs and expanded 4 UART ports + IrDA
	Ethernet, USB
Other peripherals:
	TWL5030 PMIC+Audio+Keypad
	VGA display
Expansion ports:
	Memory devices plugin boards (PISMO)
	Connectivity board for GPS,WLAN etc.
Completely configurable boot sequence and device mapping
etc.

Support default jumpering and:
 - UART1/ttyS0 console(legacy sdp3430 u-boot)
 - UART3/ttyS2 console (matching other boards,
		 and SDP HW docs)
 - Ethernet
 - mmc0
 - NOR boot

Currently the UART1 is enabled by default.  for
compatibility with other OMAP3 u-boot platforms,
enable the #define of CONSOLE_J9.

Conflicts:

	Makefile

Fixed the conflict with smdkc100_config by moving omap_sdp3430_config
to it is alphabetically sorted location above zoom1.

Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>

This patch adds support for the leopard board which is
based on the DM355 SOC.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

This patch adds the initial support for DM6467 EVM.
Other features like NET and NAND support will be added as follow up patches.

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>

On Chip BootROM support for P1 and P2 series RDB platforms.

This patch is derived from latest On Chip BootROM support on MPC8536DS

Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

NAND Boot support for P1 and P2 series RDB platforms.

This patch is derived from NAND Boot support on MPC8536DS.

Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

Adds new board SMDKC100 that uses s5pc100 SoC

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>

The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.

Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>

these boards are built around Atmel's AT91SAM9260/9G20 and have
up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND
and include a 10/100 Ethernet PHY in RMII mode.

Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>