u-boot.git/README, branch v2009.03

8xx, icache: enabling ICache not before running from RAM

2009-03-18T19:48:29+00:00

with the new CONFIG_SYS_DELAYED_ICACHE config option, ICache
is not enabled before code runs from RAM.

Signed-off-by: Heiko Schocher

README: remove duplicate entry

2009-02-19T00:01:25+00:00

it's been around since the original commit (2ad6b513) that added two
identical entries.

Signed-off-by: Kim Phillips

Create configuration option for restricted ns16550 functions

2009-02-18T23:34:51+00:00

This patch will create a configuration option for a minimum configuration for
the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new
configuration option to the SIMPC8313.h config file in order to fix the NAND
bootstrap build error.  This option will exclude all functions with exception of
NS16550_putc and NS16550_init.  This will be used primarily to save space and
remove unused code from builds in which space is limited.

Signed-off-by: Ron Madrid

rename CONFIG_CMD_ENV to CONFIG_CMD_SAVEENV

2009-02-17T23:47:43+00:00

The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment.  So, let's make sure the define is named accordingly.

Signed-off-by: Mike Frysinger

ppc4xx: Add README entry for CONFIG_PCI_DISABLE_PCIE

2009-02-12T05:18:20+00:00

Signed-off-by: Dirk Eibach 
Signed-off-by: Stefan Roese

8xx serial, smc: add configurable SMC Rx buffer len

2009-02-11T22:18:13+00:00

This patch adds the configuration option CONFIG_SYS_SMC_RXBUFLEN.
With this option it is possible to allow the receive
buffer for the SMC on 8xx to be greater then 1. In case
CONFIG_SYS_SMC_RXBUFLEN == 1 this driver works as the
old version.

When defining CONFIG_SYS_SMC_RXBUFLEN also
CONFIG_SYS_MAXIDLE must be defined to setup the maximum
idle timeout for the SMC.

Signed-off-by: Heiko Schocher

82xx serial, smc: add configurable SMC Rx buffer len

2009-02-09T23:54:42+00:00

This patch adds the configuration option CONFIG_SYS_SMC_RXBUFLEN.
With this option it is possible to allow the receive
buffer for the SMC on 82xx to be greater then 1. In case
CONFIG_SYS_SMC_RXBUFLEN == 1 this driver works as the
old version.

When defining CONFIG_SYS_SMC_RXBUFLEN also
CONFIG_SYS_MAXIDLE must be defined to setup the maximum
idle timeout for the SMC.

Signed-off-by: Heiko Schocher

ixp: remove the option to include the Microcode

2009-01-31T08:53:39+00:00

instead the board will have to load it from flash or ram
which will be specified by npe_ucode env var

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD

Command usage cleanup

2009-01-28T07:49:52+00:00

Remove command name from all command "usage" fields and update
common/command.c to display "name - usage" instead of
just "usage". Also remove newlines from command usage fields.

Signed-off-by: Peter Tyser

soft_i2c.c add option for repeated start in i2c_read()

2009-01-27T21:26:31+00:00

This patch adds a #define to optionally change the behaviour of
i2c_read() in soft_i2c.c to send an I2C repeated start instead of a
stop-start between sending the device address pointer write and
reading back the data.  The current behaviour is retained as the
default.

While most devices will work either way, I have a smart battery(*)
that requires repeated start, and someone at some point found a
device that required a stop-start.

(*) http://www.inspired-energy.com/Standard_Products/NL2054/NL2054%20Rev1.0%20Data%20Sheet.pdf

Signed-off-by: Andrew Dyer