u-boot.git/README, branch v2014.01

sf: Add CONFIG_SF_DUAL_FLASH

2014-01-12T16:10:22+00:00

This config will use for defining greater than single flash support.
currently - DUAL_STACKED and DUAL_PARALLEL.

Signed-off-by: Jagannadha Sutradharudu Teki

powerpc/mpc85xx: Add support for single source clocking

2014-01-02T22:10:13+00:00

Single-source clocking is new feature introduced in T1040.
In this mode, a single differential clock is supplied to the
DIFF_SYSCLK_P/N inputs to the processor, which in turn is
used to supply clocks to the sysclock, ddrclock and usbclock.

So, both ddrclock and syclock are driven by same differential
sysclock in single-source clocking mode whereas in normal clocking
mode, generally separate DDRCLK and SYSCLK pins provides
reference clock for sysclock and ddrclock

DDR_REFCLK_SEL rcw bit is used to determine DDR clock source
-If DDR_REFCLK_SEL rcw bit is 0, then DDR PLLs are driven in
 normal clocking mode by DDR_Reference clock

-If DDR_REFCLK_SEL rcw bit is 1, then DDR PLLs are driven in
 single source clocking mode by DIFF_SYSCLK

Add code to determine ddrclock based on DDR_REFCLK_SEL rcw bit.

Signed-off-by: Poonam Aggrwal 
Signed-off-by: Priyanka Jain

board/freescale:Remove use of CONFIG_SPL_NAND_MINIMAL

2014-01-02T22:10:13+00:00

CONFIG_SPL_NAND_MINIMAL should not be used as it was defined for temporary
review purpose.

So, use CONFIG_SPL_NAND_BOOT config.

Signed-off-by: Prabhakar Kushwaha

Add dumpimage, a tool to extract data from U-Boot images

2013-12-13T14:15:32+00:00

Given a multi-file image created through the mkimage's -d option:

  $ mkimage -A x86 -O linux -T multi -n x86 -d vmlinuz:initrd.img:System.map \
  multi.img

  Image Name:   x86
  Created:      Thu Jul 25 10:29:13 2013
  Image Type:   Intel x86 Linux Multi-File Image (gzip compressed)
  Data Size:    13722956 Bytes = 13401.32 kB = 13.09 MB
  Load Address: 00000000
  Entry Point:  00000000
  Contents:
     Image 0: 4040128 Bytes = 3945.44 kB = 3.85 MB
     Image 1: 7991719 Bytes = 7804.41 kB = 7.62 MB
     Image 2: 1691092 Bytes = 1651.46 kB = 1.61 MB

It is possible to perform the innverse operation -- extracting any file from
the image -- by using the dumpimage's -i option:

  $ dumpimage -i multi.img -p 2 System.map

Although it's feasible to retrieve "data files" from image through scripting,
the requirement to embed tools such 'dd', 'awk' and 'sed' for this sole purpose
is cumbersome and unreliable -- once you must keep track of file sizes inside
the image. Furthermore, extracting data files using "dumpimage" tool is faster
than through scripting.

Signed-off-by: Guilherme Maciel Ferreira 
Signed-off-by: Simon Glass

Merge branch 'master' of git://git.denx.de/u-boot-arm

2013-12-10T22:15:18+00:00

Conflicts:
	board/samsung/trats2/trats2.c
	include/configs/exynos5250-dt.h

Signed-off-by: Tom Rini

Merge branch 'u-boot/master' into 'u-boot-arm/master'

2013-12-10T21:23:59+00:00

Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds

i2c: samsung: register i2c busses for Exynso5420 and Exynos5250

2013-12-06T06:46:23+00:00

This patch adds the U_BOOT_I2C_ADAP_COMPLETE defines for channels
on Exynos5420 and Exynos5250 and also adds support for init function
for hsi2c channels

Signed-off-by: Naveen Krishna Chatradhi

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

2013-12-02T13:38:28+00:00

Driver/DDR: Add Freescale DDR driver for ARM

2013-11-25T19:43:46+00:00

Make PowerPC specific code conditional so ARM SoCs can reuse
this driver. Add DDR3 driver for ARM.

Signed-off-by: York Sun

Driver/DDR: Moving Freescale DDR driver to a common driver

2013-11-25T19:43:43+00:00

Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.

Signed-off-by: York Sun