u-boot.git/arch/arm/cpu/armv7/mx6, branch master

imx: reorganize IMX code as other SOCs

2017-07-12T08:17:44+00:00

Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic 

CC: Fabio Estevam 
CC: Akshay Bhat 
CC: Ken Lin 
CC: Marek Vasut 
CC: Heiko Schocher 
CC: "Sébastien Szymanski" 
CC: Christian Gmeiner 
CC: Stefan Roese 
CC: Patrick Bruenn 
CC: Troy Kisky 
CC: Nikita Kiryanov 
CC: Otavio Salvador 
CC: "Eric Bénard" 
CC: Jagan Teki 
CC: Ye Li 
CC: Peng Fan 
CC: Adrian Alonso 
CC: Alison Wang 
CC: Tim Harvey 
CC: Martin Donnelly 
CC: Marcin Niestroj 
CC: Lukasz Majewski 
CC: Adam Ford 
CC: "Albert ARIBAUD (3ADEV)" 
CC: Boris Brezillon 
CC: Soeren Moch 
CC: Richard Hu 
CC: Wig Cheng 
CC: Vanessa Maegima 
CC: Max Krummenacher 
CC: Stefan Agner 
CC: Markus Niebel 
CC: Breno Lima 
CC: Francesco Montefoschi 
CC: Jaehoon Chung 
CC: Scott Wood 
CC: Joe Hershberger 
CC: Anatolij Gustschin 
CC: Simon Glass 
CC: "Andrew F. Davis" 
CC: "Łukasz Majewski" 
CC: Patrice Chotard 
CC: Nobuhiro Iwamatsu 
CC: Hans de Goede 
CC: Masahiro Yamada 
CC: Stephen Warren 
CC: Andre Przywara 
CC: "Álvaro Fernández Rojas" 
CC: York Sun 
CC: Xiaoliang Yang 
CC: Chen-Yu Tsai 
CC: George McCollister 
CC: Sven Ebenfeld 
CC: Filip Brozovic 
CC: Petr Kulhavy 
CC: Eric Nelson 
CC: Bai Ping 
CC: Anson Huang 
CC: Sanchayan Maity 
CC: Lokesh Vutla 
CC: Patrick Delaunay 
CC: Gary Bisson 
CC: Alexander Graf 
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam 
Reviewed-by: Christian Gmeiner

mx6sabreauto: Update to SPL only mode

2017-07-12T07:44:22+00:00

As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.

This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.

Signed-off-by: Vanessa Maegima 
Reviewed-by: Fabio Estevam 
Reviewed-by: Stefano Babic

mx6qsabreauto: Add SPL support

2017-07-12T07:44:22+00:00

Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.

Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg

Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg

Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg

Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.

Signed-off-by: Vanessa Maegima 
Reviewed-by: Fabio Estevam 
Reviewed-by: Stefano Babic

mx6: soc: Move mxs_dma_init() into the mxs nand driver

2017-07-12T07:44:22+00:00

Currently the following build error is seen when a board using MMC SPL
is built and the MXS nand driver is also selected:

arch/arm/cpu/armv7/built-in.o: In function `arch_cpu_init':
arch/arm/cpu/armv7/mx6/soc.c:432: undefined reference to 'mxs_dma_init'

On mx6 the only user of mxs_dma_init() is the mxs nand driver, so
move it there.

Signed-off-by: Fabio Estevam

imx: mx6ull: fix USB bmode for i.MX 6UL and 6ULL

2017-07-12T07:42:33+00:00

i.MX 6UL and 6ULL have different boot device capabilities and
use therefor use a different boot device selection table than
other i.MX 6 devices. Particularly, the value which has been
used so far (b0001) is assigned to QSPI boot for these two
devices.

There is no common reserved value for all i.MX 6devices. Use
b0010 for i.MX 6UL and 6ULL via compile time ifdef.

Reported-by: Joël Esponde 
Signed-off-by: Stefan Agner 
Reviewed-by: Fabio Estevam 
Tested-by: Joël Esponde

Kconfig: Add CONFIG_SATA to enable SATA

2017-07-11T16:08:19+00:00

At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng

Convert CONFIG_CMD_SATA to Kconfig

2017-07-11T16:08:19+00:00

This converts the following to Kconfig:
   CONFIG_CMD_SATA

Signed-off-by: Simon Glass 
Reviewed-by: Bin Meng

mx6: soc: Fix typo in temperature unit name

2017-06-27T07:06:09+00:00

The correct name is 'Celsius', so fix it accordingly.

Signed-off-by: Fabio Estevam

Convert CONFIG_CMD_FUSE to Kconfig

2017-05-22T13:33:58+00:00

This converts the following to Kconfig:
   CONFIG_CMD_FUSE

Signed-off-by: Simon Glass

icorem6: Make SPL to pick suitable fdt

2017-05-18T09:23:31+00:00

SPL FIT is able to pick the suitable fdt file for u-boot,
so add that function through board_fit_config_name_match.

Cc: Stefano Babic 
Cc: Matteo Lisi 
Cc: Michael Trimarchi 
Signed-off-by: Jagan Teki