u-boot.git/arch/arm/cpu/armv7m/cpu.c, branch master

arm: Add ARMv8-M aarch32 support

2026-04-13T23:34:02+00:00

Add configuration for ARMv8-M aarch32 core, which are currently
Cortex-M23/M33 cores. These cores are treated similar to ARMv7-M
cores, except the code has to be compiled with matching compiler
-march=armv8-m.main flag . These cores have no MMU, they have MPU,
which is currently not configured.

Unlike ARMv7-M, these cores have 512 interrupt vectors. While the
SYS_ARM_ARCH should be set to 8, it is set to 7 because all of the
initialization code is built from arch/arm/cpu/armv7m and not armv8.
Furthermore, CONFIG_ARM64 must be disabled, although DTs for devices
using these cores do come from arch/arm64/boot/dts.

To avoid excess duplication in Makefiles, introduce one new Kconfig
symbol, CPU_V7M_V8M. The CPU_V7M_V8M cover both ARMv7-M and ARMv8-M
cores.

Signed-off-by: Marek Vasut 
Acked-by: Udit Kumar

spl: split spl_board_fixups to arch/board specific

2025-10-22T18:05:52+00:00

The current spl_board_fixups API allows for modification of spl_image
before the SPL jumps to it. This can be used to modify the DT for the
next boot stage, however the current API only allows either the machine
arch or the board to use it.

This limits the utility of the API as there might be certain fixups that
should be applied to all boards sharing the same machine architecture
with others being board specific.

For TI's K3 specifically, this prevents us from performing architecture
level fixups since a lot of TI boards are already making use of the
spl_board_fixups API.

Therefore this patch splits the API into two to allow both board and the
architecture specific fixups. The order is kept as arch then board to
give board specific fixups the precedence.

Reviewed-by: Dhruva Gole 
Signed-off-by: Anshul Dalal 
Tested-by: Wadim Egorov

Restore patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet"

2024-05-20T19:35:03+00:00

As part of bringing the master branch back in to next, we need to allow
for all of these changes to exist here.

Reported-by: Jonas Karlman 
Signed-off-by: Tom Rini

Revert "Merge patch series "arm: dts: am62-beagleplay: Fix Beagleplay Ethernet""

2024-05-19T14:16:36+00:00

When bringing in the series 'arm: dts: am62-beagleplay: Fix Beagleplay
Ethernet"' I failed to notice that b4 noticed it was based on next and
so took that as the base commit and merged that part of next to master.

This reverts commit c8ffd1356d42223cbb8c86280a083cc3c93e6426, reversing
changes made to 2ee6f3a5f7550de3599faef9704e166e5dcace35.

Reported-by: Jonas Karlman 
Signed-off-by: Tom Rini

arm: Remove and add needed includes

2024-05-06T21:06:34+00:00

Remove  from the remainder of the files under arch/arm and
when needed add missing include files directly.

Signed-off-by: Tom Rini

common: spl: move armv7m-specific code to spl_perform_fixups()

2022-01-18T13:31:02+00:00

Factor out armv7m fragment to spl_perform_fixups(), which is an arch/board
specific function designed for this purpose.

Reviewed-by: Simon Glass 
Signed-off-by: Ovidiu Panait

reset: Remove addr parameter from reset_cpu()

2021-03-02T19:03:02+00:00

Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to.  This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value.  Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.

Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g.  COLD vs WARM resets).  As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).

To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely.  Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.

This transformation was done with the following coccinelle patch:

    @@
    expression argvalue;
    @@
    - reset_cpu(argvalue)
    + reset_cpu()

    @@
    identifier argname;
    type argtype;
    @@
    - reset_cpu(argtype argname)
    + reset_cpu(void)
    { ... }

Signed-off-by: Harald Seiler 
Reviewed-by: Simon Glass

common: Move enable/disable_interrupts out of common.h

2019-12-02T23:25:01+00:00

Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.

Signed-off-by: Simon Glass 
Reviewed-by: Tom Rini

common: Move some cache and MMU functions out of common.h

2019-12-02T23:23:55+00:00

These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.

Move them over.

Signed-off-by: Simon Glass 
Reviewed-by: Tom Rini

SPDX: Convert all of our single license tags to Linux Kernel style

2018-05-07T13:34:12+00:00

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini